Synopsys HSDK clock controller generates and supplies clocks to various
controllers and peripherals within the SoC.
Each clock has assigned identifier and client device tree nodes can use
this identifier to specify the clock which they consume. All available
clocks are defined as preprocessor macros in the
dt-bindings/clock/snps,hsdk-cgu.h header and can be used in device
tree sources.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Add bits to support yet another SoC, the R8A77995 D3 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add bits to support yet another SoC, the R8A77970 V3M .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add dts binding header for rk3128, files origin from kernel.
Series-Changes: 2
- fix i2c address
- add saradc and usb phy node
- emmc using fifo mode for there is no dma support in rk3128 emmc
- add some clock id in cru.h
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
MMC block needs 48Mhz source clock, for that we choose
to select the SAI PLL.
Update also stm32_clock_get_rate() to retrieve the MMC
clock source needed in MMC driver.
STM32F4 uses a different RCC variant than STM32F7. For STM32F4
sdmmc clocks bit are located into dckcfgr register whereas there
are located into dckcfgr2 registers on STM32F7.
In both registers, bits CK48MSEL and SDMMC1SEL are located at
the same position.
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Zynq:
- Add support for Syzygy and cc108 boards
- Add support for mini u-boot configurations (cse)
- dts updates
- config/defconfig updates in connection to Kconfig changes
- Fix psu_init handling
ZynqMP:
- SPL fixes
- Remove slcr.c
- Fixing r5 startup sequence
- Add support for external pmufw
- Add support for new ZynqMP chips
- dts updates
- Add support for zcu102 rev1.0 board
Drivers:
- nand: Support external timing setting and board init
- ahci: Fix wording
- axi_emac: Wait for bit, non processor mode, readl/write conversion
- zynq_gem: Fix SGMII/PCS support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAloeqWoACgkQykllyylKDCHO1wCggsSgQqOPdCo207FqI3yj2p0E
MYkAoI1wKvQcjGJJY19YEC1r70Op8RNo
=BqNN
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2018.01' of git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2018.1
Zynq:
- Add support for Syzygy and cc108 boards
- Add support for mini u-boot configurations (cse)
- dts updates
- config/defconfig updates in connection to Kconfig changes
- Fix psu_init handling
ZynqMP:
- SPL fixes
- Remove slcr.c
- Fixing r5 startup sequence
- Add support for external pmufw
- Add support for new ZynqMP chips
- dts updates
- Add support for zcu102 rev1.0 board
Drivers:
- nand: Support external timing setting and board init
- ahci: Fix wording
- axi_emac: Wait for bit, non processor mode, readl/write conversion
- zynq_gem: Fix SGMII/PCS support
Added pin control support in device tree for zynqmp.
Signed-off-by: Chirag Parekh <chirag.parekh@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Synchronize the Amlogic ARM64 dts from mainline Linux 4.13.5
In the preparation of the support of the Amlogic P212 board,
import the corresponding meson-gxl-s905x-p212.dts file.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Beniamino Galvani <b.galvani@gmail.com>
Upstream Linux has received a few device tree updates to the RPi
which we should propagate into the builtin U-Boot one as well to
gain hardware support.
This patch bumps the dts files to their 4.14 Linux counterparts
with the exception of sdhost on 32bit RPi versions. There we stay
with iproc as the sdhost driver is missing in U-Boot.
Signed-off-by: Alexander Graf <agraf@suse.de>
The kernel DT of the SinA33 has evolved quite a bit. Make sure we sync it
and its upstream DTSI to be able to use the OTG. The DTs were taken from
the 4.13 kernel release.
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The clk_saradc is dividing from the 24M, clk_saradc=24MHz/(saradc_div_con+1).
SARADC integer divider control register is 10-bits width.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch adapts stm32h743 disco and eval dts files to match
with U-boot requirements or add features wich are not yet
upstreamed on kernel side :
_ Add RCC clock driver node and update all clocks phandle
accordingly.
By default, on kernel side, all clocks was temporarly
configured as a phandle to timer_clk waiting for a RCC
clock driver to be available.
On U-boot side, we now have a dedicated RCC clock driver, we
can configured all clocks as phandle to this driver.
All this binding update will be available soon in a kernel tag,
as all the bindings have been acked by Rob Herring [1].
[1] http://lkml.iu.edu/hypermail/linux/kernel/1704.0/00935.html
_ Align STM32H7 serial compatible string with the one which will be
available in next kernel tag. The bindings has been acked by
Rob Herring [2].
This compatible string will be usefull to add stm32h7 specific
feature for this serial driver.
[2] https://lkml.org/lkml/2017/7/17/739
_ Add gpio compatible and aliases for stm32h743
_ Add FMC sdram node with associated new bindings value to
manage second bank (ie bank 1).
_ Add missing HSI and CSI oscillators nodes needed
by STM32H7 RCC clock driver.
Clock sources could be:
_ HSE (High Speed External)
_ HSI (High Speed Internal)
_ CSI (Low Power Internal)
These clocks can be used as clocksource in some configuration.
By default, HSE is selected as clock source.
_ Set HSE to 25Mhz for stm32h743i-disco and eval board
By default, the external oscillator frequency is defined at
25 Mhz in SoC stm32h743.dtsi file.
It has been set at 125 Mhz in kernel DT temporarly waiting for
RCC clock driver becomes available.
As in U-boot we got a RCC clock driver, the real value of HSE
clock can be used.
_ Add "u-boot,dm-pre-reloc" for rcc, fmc, fixed-clock, pinctrl,
pwrcfg and gpio nodes.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
All these files are imported from linux kernel v4.13
Add device tree support for STM32H743 SoC and discovery
board. This board offers :
_ STM32H743XIH6 microcontroller with 2 Mbytes of
Flash memory and 1 Mbyte of RAM in TFBGA240+25 package
_ 5.7” 640x480 TFT color LCD with touch screen
_ Ethernet compliant with IEEE-802.3-2002
_ USB OTG HS
_ I2 C compatible serial interface
_ ST-MEMS digital microphones
_ 8-Gbyte (or more) SDIO3.0 interface microSD™ card
_ 8Mx32bit SDRAM
_ 1-Gbit Twin Quad-SPI NOR Flash
_ Reset, wakeup, or key buttons
_ Joystick with 4-direction control and selector
_ Board connectors :
1 USB with Micro-AB
Ethernet RJ45
Stereo headset jack including analog microphone input
microSD™ card
RCA connector
JTAG/SWD and ETM trace
_ Expansion connectors:
Arduino Uno compatible Connectors
2 x PIO connectors (PMOD and PMOD+)
_ On-board ST-LINK/V2-1 debugger/programmer with USB re-enumeration
capability: mass storage, virtual COM port and debug port
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver is adapted from linux drivers/reset/reset-stm32.c
It's compatible with STM32 F4/F7/H7 SoCs.
This driver doesn't implement .of_match as it's binded
by MFD RCC driver.
To add support for each SoC family, a SoC's specific
include/dt-binfings/mfd/stm32xx-rcc.h file must be added.
This patch only includes stm32h7-rcc.h dedicated for STM32H7 SoCs.
Other SoCs support will be added in the future.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver implements basic clock setup, only clock gating
is implemented.
This driver doesn't implement .of_match as it's binded
by MFD RCC driver.
Files include/dt-bindings/clock/stm32h7-clks.h and
doc/device-tree-bindings/clock/st,stm32h7-rcc.txt
will be available soon in a kernel tag, as all the
bindings have been acked by Rob Herring [1].
[1] http://lkml.iu.edu/hypermail/linux/kernel/1704.0/00935.html
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a DRAM controller driver for the RK3368 and places it in
drivers/ram/rockchip (where the other DM-enabled DRAM controller
drivers for rockchip devices should also be moved eventually).
At this stage, only the following feature-set is supported:
- DDR3
- 32-bit configuration (i.e. fully populated)
- dual-rank (i.e. no auto-detection of ranks)
- DDR3-1600K speed-bin
This driver expects to run from a TPL stage that will later return to
the RK3368 BROM. It communicates with later stages through the
os_reg2 in the pmugrf (i.e. using the same mechanism as Rockchip's DDR
init code).
Unlike other DMC drivers for RK32xx and RK33xx parts, the required
timings are calculated within the driver based on a target frequency
and a DDR3 speed-bin (only the DDR3-1600K speed-bin is support at this
time).
The RK3368 also has the DDRC0_CON0 (DDR ch. 0, control-register 0)
register for controlling the operation of its (single-channel) DRAM
controller in the GRF block. This provides for selecting DDR3, mobile
DDR modes, and control low-power operation.
As part of this change, DDRC0_CON0 is also added to the GRF structure
definition (at offset 0x600).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Import the RCar Gen3 DTS and headers from upstream Linux kernel v4.12-rc6,
commit 6f7da290413ba713f0cdd9ff1a2a9bb129ef4f6c . This includes both M3
and H3 ULCB and Salvator-X boards.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Use the same clocks macro than the one used by kernel DT.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Vikas MANOCHA <vikas.manocha@st.com>
Import Amlogic Meson DTS files from Linux kernel version 4.12
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The dts files are from kernel and with modify to adapt U-Boot.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The RK3368 is an octa-core Cortex-A53 SoC from Rockchip.
This adds basic support to chain-load U-Boot from Rockchip's
miniloader.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Linux device tree for the Allwinner A64 SoC has changed a lot since
the U-Boot version was merged.
Let's replace the current DT with a exact copy of the Linux one as of:
commit c6778ff813d2ca3e3c8733c87dc8b6831a64578b
Merge: 0ff4c01 3c0e3abd
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Tue May 9 10:07:33 2017 -0700
This is the DT used in Linux 4.12-rc1.
Since U-Boot has an Ethernet driver (while Linux does not yet), we
provide the required DT nodes for it in an ...-u-boot.dtsi file, to both
mark them as U-Boot specific and to allow easier upgrading once Linux gets
the driver and its own binding later.
Compared to the existing Ethernet DT nodes we just slightly tweak the clock
and reset nodes in there to match the new bindings used by Linux for those.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Sync with Linux commit 308ac756("Merge tag 'gpio-v4.11-3'").
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefan Agner <stefan.agner@toradex.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
This adds a new firefly-rk3399 board, MIPI support for rk3399 and
rk3288, rk818 pmic support, mkimage improvements for rockchip and a few
other things.
The kernel dts has update a lot since the first time we commit rk3399.dtsi,
sync with kernel for further development.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add device tree support to allow for CONFIG_OF_CONTROL in OMAP3630 boards.
DM3730 can use this same device tree.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
This patch adds the option to configure a comphy to 5G XFI mode.
In order to configure the comphy to 5G XFI, update
the comphy node in the device-tree:
phy2 {
phy-type = <PHY_TYPE_SFI>;
phy-speed = <PHY_SPEED_5_15625G>;
};
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This type tells u-boot to preserve the COMPHY settings as is
it is usefull in situations where the COMPHY was initialized by
earlier firmware.
Note that IGNORE is different from UNCONNECTED since setting
UNCONNECTED type will disconnect the COMPHY in the COMPHY MUX
which is a desired behaviour
Signed-off-by: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
UTMI_PHY_TO_USB_HOST was used in USB3 UTMI dts node only, but there will
be USB2 UTMI dts node for some SoCs that have got USB2 controller, so rename
TO_USB_HOST to TO_USB3_HOST to distinguish TO_USB2_HOST in later on patches.
Signed-off-by: zachary <zhangzg@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Use correct naming as done in the latest Marvell U-Boot version as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add support for clocks needed by MACs to ast2500 clock driver.
The clocks are D2-PLL, which is used by both MACs and PCLK_MAC1 and
PCLK_MAC2 for MAC1 and MAC2 respectively.
The rate of D2-PLL is hardcoded to 250MHz -- the value used in Aspeed
SDK. It is not entirely clear from the datasheet how this clock is used
by MACs, so not clear if the rate would ever need to be different. So,
for now, hardcoding it is probably safer.
The rate of PCLK_MAC{1,2} is chosen based on MAC speed selected through
hardware strapping.
So, the network driver would only need to enable these clocks, no need
to configure the rate.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add Reset Driver configuration to ast2500 SoC Device Tree and bindings
for various reset signals
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Actually the sdram memory on stm32f746 discovery board is micron part
MT48LC_4M32_B2B5_6A. This patch does the modification required in the
device tree node & driver for the same.
Also we are passing here all the timing parameters in terms of clock
cycles, so no need to convert time(ns or ms) to cycles.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
As we have now V3s support in board code, the V3s DTSI file should also
be added.
Add also some CCU include headers to satisfy the DTSI file.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As a prerequisite for adding a Meson GX MMC driver update the
Meson GXBB / Odroid-C2 device tree in Uboot with the latest
version from Linux.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
AT91 PIO controller is a combined gpio-controller, pin-mux and
pin-config module. The peripheral's pins are assigned through
per-pin based muxing logic.
Each SoC will have to describe the its limitation and pin
configuration via device tree. This will allow to do not need
to touch the C code when adding new SoC if the IP version is
supported.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce device tree support.
dts from kernel commit c4f3f22edd Merge tag 'linux-kselftest-4.11-rc1'
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add dts binding header for rk3328, files origin from kernel.
Signed-off-by: William Zhang <william.zhang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Bring in required device clock binding files from Linux.
The clock trees for rk3066 and rk3188 are largely similar, which makes
them share the common parts in a shared header. While we focus on rk3188
for now, bring in both headers already for completeness sake.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
This device tree has been extracted from v4.9 kernel
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds pin control definitions for use in device tree files
The definitions are based on the stm32f746 files from current
linux kernel "include/dt-bindings/pinctrl/stm32f746-pinfunc.h".
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Vikas MANOCHA <vikas.manocha@st.com>
Clock Driver
This driver is ast2500-specific and is not compatible with earlier
versions of this chip. The differences are not that big, but they are
in somewhat random places, so making it compatible with ast2400 is not
worth the effort at the moment.
SDRAM MC driver
The driver is very ast2500-specific and is completely incompatible
with previous versions of the chip.
The memory controller is very poorly documented by Aspeed in the
datasheet, with any mention of the whole range of registers missing. The
initialization procedure has been basically taken from Aspeed SDK, where
it is implemented in assembly. Here it is rewritten in C, with very limited
understanding of what exactly it is doing.
Reviewed-by: Simon Glass <sjg@chromium.org>
Add i.MX6UL dtsi support from Linux.
Here is the last commit:
"ARM: dts: add gpio-ranges property to iMX GPIO controllers"
(sha1: bb728d662bed0fe91b152550e640cb3f6caa972c)
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add CX9020 board based on mx53loco.
Add simplified imx53 base device tree from kernel v4.8-rc8, to reuse
serial_mxc with DTE and prepare for device tree migration of other
functions and imx53 devices.
The CX9020 differs from i.MX53 Quick Start Board by:
- use uart2 instead of uart1
- DVI-D connector instead of VGA
- no audio
- CCAT FPGA connected to emi
- enable rtc
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
This patch adds dt-bindings as used by the linux kernel device trees
for the bcm283x family.
Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Fabian Vogt <fvogt@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add i.mx6ul clock header, copied from kernel commit (29b4817d401).
i.MX6ULL reuse the file in Linux Kernel, so let's keep the same.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
The primary benefit of this change is that it adds all missing clocks and
resets properties to peripherals. This will allow peripheral drivers to
migrate to the standard clock and reset APIs in the future.
Main changes:
* Brought in the correct Tegra210 CAR binding; the old file in U-Boot
appears to be a renamed version of the Tegra124 bindings rather than
the real Tegra210 version.
* Conversion of SPI and UART nodes to standard DMA bindings. U-Boot
doesn't use DMA so isn't affected.
* Split of EHCI and USB PHY nodes. The EHCI nodes continue to contain all
information required by U-Boot, so U-Boot is not affected.
* Conversion of many magic numbers to named defines.
* Addition of many nodes not used by U-Boot, including separation of the
Tegra LIC (Legacy IRQ controller) and GIC.
* Node sort order fixes.
Remaining deltas relative to the Linux DT:
* U-Boot has enabled PCIe for Tegra210, but the kernel hasn't yet.
* The GPIO node compatible value in the kernel explicitly includes
Tegra124 values whereas U-Boot does not. I'll send a kernel patch to
correct this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The primary benefit of this change is that it adds all missing clocks and
resets properties to peripherals. This will allow peripheral drivers to
migrate to the standard clock and reset APIs in the future.
Main changes:
* USB phy_type property is aligned with the kernel, so board files are
updated so the final DT content doesn't change. I'm not convinved that
Nyan uses HSIC phy_type. However, I'd rather this change be a no-op,
and any DT bug-fixes be separate.
* Sync misc changes from the kernel: missing DT content, minor compatible
value fixes, typos.
Remaining deltas relative to the Linux DT:
* U-Boot uses #address-cells/#size-cells of 1 whereas the kernel uses 2.
I believe U-Boot's DT parsing currently assumes that these values match
the physical address size, so I didn't synchronize this part of the DT.
* U-Boot uses the original XUSB PHY DT binding, wherease the kernel DT
has moved to a newer version. Thus, XUSB client nodes include properties
names phys and phy-names that do not appear in the kernel, and don't
include pad definitions in the padctl node.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The primary benefit of this change is that it adds all missing clocks and
resets properties to peripherals. This will allow peripheral drivers to
migrate to the standard clock and reset APIs in the future.
Main changes:
* Conversion of SPI nodes to standard DMA bindings. U-Boot doesn't use
DMA so isn't affected.
* Split of EHCI and USB PHY nodes. The EHCI nodes continue to contain all
information required by U-Boot, so U-Boot is not affected.
* Boards need to define the clk32k_in clock that feeds the Tegra PMC.
* Addition of tegra114-mc.h since tegra114.dtsi now includes it.
* Conversion of many magic numbers to named defines.
* Addition of many nodes not used by U-Boot.
* Node sort order fixes.
Remaining deltas relative to the Linux DT:
* USB node compatible values in U-Boot explicitly list Tegra114 values
whereas the kernel does not. I'll send a kernel patch to correct this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The primary benefit of this change is that it adds all missing clocks and
resets properties to peripherals. This will allow peripheral drivers to
migrate to the standard clock and reset APIs in the future.
Main changes:
* Modification of PCIe memory region addresses. The HW memory layout is
programmable, so this should work fine, and Beaver PCIe was tested
without issue.
* Removal of pcie_xclk from the PCIe node and clock binding header. This
clock doesn't exist and isn't used; only a reset with this ID exists.
* Conversion of SPI nodes to standard DMA bindings. U-Boot doesn't use
DMA so isn't affected.
* Split of EHCI and USB PHY nodes. The EHCI nodes continue to contain all
information required by U-Boot, so U-Boot is not affected.
* Changed the phy_type value for the second USB port. This required board
DTs to be updated to keep the same configuration.
* Boards need to define the clk32k_in clock that feeds the Tegra PMC.
* Addition of tegra30-mc.h since tegra30.dtsi now includes it.
* Conversion of many magic numbers to named defines.
* Addition of many nodes not used by U-Boot.
* Node sort order fixes.
Remaining deltas relative to the Linux DT:
* None.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This brings in a few minor fixes since the last sync. The largest change
is the removal of the definition for TEGRA20_CLK_PCIE_XCLK. This clock
doesn't actually exist.
Remaining deltas:
* Addition of u-boot,dm-pre-reloc property to a couple of nodes.
* Addition of the NAND controller, which Linux doesn't yet support.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This version is based on the Marvell U-Boot version with this patch
applied as latest patch:
Git ID 7f408573: "fix: comphy: cp110: add comphy initialization for usb
device mode" from 2016-07-05.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Add a simple driver for the clocks provided by the MIPS Boston
development board. The system provides information about 2 clocks whose
rates are fixed by the bitfile flashed in the boards FPGA, and this
driver simply reads the rates of these 2 clocks.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Import a copy of the dt-bindings/interrupt-controller/mips-gic.h header
from Linux, such that we can use device trees which include it without
modification.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Import DTS files and dt-bindings includes from Linux 4.8-rc1.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sync dts files with the current (Aug 18th 2016) state of Maxime's
linux/sunxi/for-next repo.
Note this commit also updates configs/MSI_Primo81_defconfig,
adding: "# CONFIG_REQUIRE_SERIAL_CONSOLE is not set", this is necessary
because the tablet does not have a reachable uart so the dts sync
drops its serial0 alias.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Tegra BPMP (Boot and Power Management Processor) is a separate
auxiliary CPU embedded into Tegra to perform power management work, and
controls related features such as clocks, resets, power domains, PMIC I2C
bus, etc. These bindings dictate how to represent the BPMP in device tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The DT binding for the Tegra186 HSP module apparently wasn't quite final
when I posted initial U-Boot support for it. Add the final DT binding doc
and adapt all code and DT files to match it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
These files are from kernel upstream:
"649a371 Add linux-next specific files for 20160616"
with some modification need by U-Boot:
- chosen with stdout-path to uart2.
- add clock-frequency for uart2
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tegra186's HSP module implements doorbells, mailboxes, semaphores, and
shared interrupts. This patch provides a driver for HSP, and hooks it
into the mailbox API. Currently, only doorbells are supported.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Tegra186's GPIO controller register layout is significantly different from
previous chips, so add a new driver for it. In fact, there are two
different GPIO controllers in Tegra186 that share a similar register
layout, but very different port mapping. This driver covers both.
The DT binding is already present in the Linux kernel (in linux-next via
the Tegra tree so far).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org> # v1
Signed-off-by: Tom Warren <twarren@nvidia.com>
According to the Tegra TRM, GPIOs are aggregated into /ports/ of 8 GPIOs,
not into /banks/. Fix <dt-bindings/gpio/tegra-gpio.h> to correctly reflect
this naming convention. While this seems like silly churn, it will become
slightly more important once we introduce the GPIO binding for upcoming
Tegra chips. This mirrors an identical commit in the Linux kernel.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
These are used by peach_pit and peach_pi. Add them so they can be referenced
in the device tree files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add a clock driver for Exynos7420 SoC. There are about 25 clock controller
blocks in Exynos7420 out of which support for topc, top0 and peric1 blocks
are added in this initial version of the driver.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add the device tree bindings and the accompanying documentation
for the TI DP83867 Giga bit ethernet phy driver.
The original document was from:
[commit 2a10154abcb75ad0d7b6bfea6210ac743ec60897 from the Linux kernel]
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Import the upstream kernel dts into U-Boot. Currently
only serial is supported, but a lot more DT changes are
queued for v4.7.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This commit syncs the dt-bindings/input/* headers with the kernel (v4.5)
and adds dt-bindings/clock/sun4i-a10-pll2.h, both are necessary for newer
sunxi dts files to build.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
GPIO pins need to be set up on start-up. Add a driver to provide this,
configured from the device tree.
The binding is slightly different from the existing ICH6 binding, since that
is quite verbose. The new binding should be just as extensible.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
PIC32 clock module consists of multiple oscillators, PLLs, mutiplexers
and dividers capable of supplying clock to various controllers
on or off-chip.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously. Convert all of these to the correct SPDX-License-Identifier
tag.
Signed-off-by: Tom Rini <trini@konsulko.com>
Since rk3036 device tree file still in reviewing, bring it from
https://patchwork.kernel.org/patch/7203371/ and add some aliases
we need in uboot
Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Import various DT files for am4372, an43xx pinctrl and
am437x-gp-evm from Linux Kernel v4.2
Add config file for this board, enable DM, DM_GPIO, DM_SERIAL
and DM_MMC.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Bring in required device tree files from Linux. Since mainline Linux is
somewhat behind, use the files from the Chromium tree. We can re-sync once
further code is acccepted upstream.
Signed-off-by: Simon Glass <sjg@chromium.org>
- Import various DT files for DRA7 / DR72x / dra72-evm from Linux Kernel
v4.1
- Add config file for this board, enable DM and DM_GPIO
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
All based off of Tegra124. As a Tegra210 board is brought
up, these may change a bit to match the HW more closely,
but probably 90% of this is identical to T124.
Note that since T210 is a 64-bit build, it has no SPL
component, and hence no cpu.c for Tegra210.
Signed-off-by: Tom Warren <twarren@nvidia.com>
This also came from Linux - according to this thread it has a GPL v2
license like arch/arm/mach-omap2/mux.h:
http://lists.denx.de/pipermail/u-boot/2015-June/217827.html
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Ingrid Viitanen <ingrid.viitanen@nokia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Every pin can be configured now from the device tree. A dt-bindings
has been added to describe the different property available.
Change-Id: I1668886062655f83700d0e7bbbe3ad09b19ee975
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
Acked-by: Simon Glass <sjg@chromium.org>
PIRQ routing is pretty much common in Intel chipset. It has several
PIRQ links (normally 8) and corresponding registers (either in PCI
configuration space or memory-mapped IBASE) to configure the legacy
8259 IRQ vector mapping. Refactor current Queensbay PIRQ routing
support using device tree and move it to a common place, so that we
can easily add PIRQ routing support on a new platform.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit adds dtsi file for Sandbox PMIC.
It fully describes the PMIC by:
- i2c emul node - with a default settings of 16 registers
- 2x buck regulator nodes
- 2x ldo regulator nodes
The default register settings are set with preprocessor macros:
- VAL2REG(min[uV/uA], step[uV/uA], val[uV/uA])
- VAL2OMREG(mode id)
Both defined in file:
- include/dt-bindings/pmic/sandbox_pmic.h
The Voltage ranges of each regulator can be found in:
- include/power/sandbox_pmic.h
The new file is included into:
- sandbox.dts
- test.dts
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested on sandbox:
Tested-by: Simon Glass <sjg@chromium.org>
Bring all the sunxi dts files (and update existing ones) from
mripard/sunxi/dt-for-4.1 (which will be merged into upstream master any
day now). This is necessary so that we can move all sunxi boards over to
the driver model.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add standard dt-bindings macros to be used by Intel Quark MRC node.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add the device tree node for the PCIe controller found on Tegra30 SoCs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add the device tree node for the PCIe controller found on Tegra20 SoCs.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This controller was introduced on Tegra114 to handle XUSB pads. On
Tegra124 it is also used for PCIe and SATA pin muxing and PHY control.
Only the Tegra124 PCIe and SATA functionality is currently implemented,
with weak symbols on Tegra114.
Tegra20 and Tegra30 also provide weak symbols for these functions so
that drivers can use the same API irrespective of which SoC they're
being built for.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Sync this up with Linux v3.18-rc5. Exclude features that are unlikely to
supported in U-Boot soon (regulators, pinmux). Also the addresses are
updated to 32-bit. Otherwise it is the same. Also bring in the dt-bindings
for pinctrl.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
This patch includes the latest DT sources for socfpga from the current
Linux kernel. And enables CONFIG_OF_CONTROL for the new build target
"socfpga_socrates" (the EBV SoCrates board) to make use of this new DT
support.
Until this patch, the only SoCFPGA U-Boot target in mainline is
"socfpga_cyclone5". This build target is not (yet) changed to support
DT. So nothing changes for this target. Even though the long-term
goal should be to move all SoCFPGA targets over to DT.
One of the reasons to enable DT support in SoCFPGA is, that I need to
support multiple different SPI controllers for this platform. This is
the QSPI Cadence controller and the Designware SPI master controller.
Both are implemented in the SoCFPGA. And enabling both controllers is
only possible by using the new driver model (DM). The DM SPI code
only supports DT based probing. So it was easier to move SoCFPGA to
DT than to add the (deprecated) platform-data based probing to the
DM SPI suport.
Note that the image with the dtb embedded is u-boot-dtb.img. This needs
to be used now for those DT enabled boards instead of u-boot.img.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Pavel Machek <pavel@denx.de>
Cc: Simon Glass <sjg@chromium.org>
These are from Linux 3.17-rc7 (commit fe82dcec). U-Boot only uses a small
portion of these, but we may as well have something to look forward to.
The total compiled size is about 25KB.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
These ended up in arch/arm/dts/dt-bindings temporarily, but in fact the
correct place is now include/dt-bindings. Move them to be consistent.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some Tegra device tree files do not include information about the serial
ports. Add this and also add information about the input clock speed.
The console alias needs to be set up to indicate which port is used for
the console.
Also add a binding file since this is missing.
Series-changes; 5
- Add full serial port nodes from Linux tree (commit fc9d4dbe)
- Use /chosen/stdout-path instead of /aliases/console to specify the console
Signed-off-by: Simon Glass <sjg@chromium.org>
