This patch try to avoids eviction of dirty lines during DMA
transfer. The code right now execute the following step:
- allocate the buffer
- start a dma operation using the non-coherent dma buffer
- invalidate cache lines associated with the buffer
- read the buffer
This can lead to reading back not valid information, because the cache
controller could evict dirty cache lines belonging to the buffer *after*
the DMA operation has started to fill the DRAM.
In order to avoid this, a new invalidation is required *before* starting
the DMA operation. The patch just adds an invalidation before submitting
the DMA command.
Example below shows the nvme disk scan result without the following
patch
=> nvme scan
nvme_get_info_from_identify: nn = 544502629, vwc = 100,
sn = dev_0T, mn = `�\�, fr = t_part, mdts = 105
So, invalidating the cache before submitting the admin command,
fix the cpu read.
Cc: André Przywara <andre.przywara@arm.com>
Reported-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Since the i.MX8 GPIO banks are indexed from 0 not 1 on other i.MX
platforms, so we have to adjust the index accordingly.
Signed-off-by: Adrian Alonso <adrian.alonso@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
As we move towards driver model, it is required to let the FEC driver
know how to properly deal with an Ethernet PHY subnode in the device tree.
For example:
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_microsom_enet_ar8035>;
phy-handle = <&phy>;
phy-mode = "rgmii-id";
phy-reset-duration = <2>;
phy-reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
status = "okay";
mdio {
#address-cells = <1>;
#size-cells = <0>;
phy: ethernet-phy@0 {
reg = <0>;
qca,clk-out-frequency = <125000000>;
};
};
};
Currently the PHY node pointer is incorrectly associated with the
Ethernel controller instead of the PHY node itself.
This causes the PHY properties, such as "qca,clk-out-frequency" in
the example above to not get parsed.
Fix this problem by populating the phy_of_node node.
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Tom Rini <trini@konsulko.com>
The clock ouput frequency is calculated incorrectly for AR8035 due to
wrong masking of priv->clk_25m_reg and priv->clk_25m_mask.
This same issue has been already fixed in the kernel by:
commit b1f4c209d84057b6d40b939b6e4404854271d797
Author: Oleksij Rempel <o.rempel@pengutronix.de>
Date: Wed Apr 1 11:57:32 2020 +0200
net: phy: at803x: fix clock sink configuration on ATH8030 and ATH8035
The masks in priv->clk_25m_reg and priv->clk_25m_mask are one-bits-set
for the values that comprise the fields, not zero-bits-set.
This patch fixes the clock frequency configuration for ATH8030 and
ATH8035 Atheros PHYs by removing the erroneous "~".
To reproduce this bug, configure the PHY with the device tree binding
"qca,clk-out-frequency" and remove the machine specific PHY fixups.
Fixes: 2f664823a47021 ("net: phy: at803x: add device tree binding")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apply the same fix in the U-Boot driver.
Tested on a i.MX6 Hummingboard.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Tested-by: Tom Rini <trini@konsulko.com>
- use 'vidconsole' stdout in nitrogen6x upgrade script
- add option for selection of the vidconsole commands
lcdputs and setcurs
- allow building ipuv3 driver with disabled CONFIG_PANEL
- make backlight and panel drivers optional
- remove useless code from ipuv3 driver
- extend existing DM_VIDEO work-around for console name
to support 'vga'
- remove non-DM code in ipuv3
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXuvRkA4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXMpeAJkB/FzsJ3O7putHrbLKOrLRF3zZYwCfQxa9jKuh
DXNTYVrHS/43T8ijGYo=
=7G75
-----END PGP SIGNATURE-----
Merge tag 'video-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-video into next
- migrate remaining imx5/imx6qd boards to DM_VIDEO
- use 'vidconsole' stdout in nitrogen6x upgrade script
- add option for selection of the vidconsole commands
lcdputs and setcurs
- allow building ipuv3 driver with disabled CONFIG_PANEL
- make backlight and panel drivers optional
- remove useless code from ipuv3 driver
- extend existing DM_VIDEO work-around for console name
to support 'vga'
- remove non-DM code in ipuv3
When CONFIG_OF_LIVE is enabled, dev_of_offset() cannot be used and
if used returns an invalid offset. This causes the call to
fdt_stringlist_get() in the psci_probe() to fail to read the 'method'
property from the PSCI node for the device and hence prevents PSCI
from working. Fix this by using the ofnode_read_string() API instead
of the fdt_stringlist_get() because this will handle reading the
property both when CONFIG_OF_LIVE is enabled or disabled.
Due to the above problem and since commit 81ea00838c ("efi_loader:
PSCI reset and shutdown") was added, the EFI system reset has been
broken for Tegra210 and Tegra196 platforms. This also fixes the EFI
system reset for these Tegra platforms.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Add Kconfig entries for the pcnet driver and convert MIPS malta
to use those.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
With all the changes in place, add support for DM into the
pcnet driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Pull the common parts of functions out so they can be reused by both
DM and non-DM code paths. The recv() function had to be reworked to
fit into this scheme and this means it now only receives one packet
at a time instead of spinning in an endless loop.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Instead of using the non-DM-only name and enetaddr in struct eth_device,
add pointers into the private data which can either point to that non-DM
name or a DM one later on.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Instead of using the non-DM-only iobase in struct eth_device, add
one into the private data to make DM and non-DM operation possible.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Get rid of the global point to private data, and rather pass it
thought dev->priv. Also remove the unnecessary check for lp being
non-NULL, since it is always NULL at this point.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Instead of using eth_device priv for this PCI devbusfn, free it
so it could be used for driver private data, and wrap devbusfn
into those driver private data.
Note that using the name dev for the variable is a trick left for
later, when DM support is in place, so dm_pci_virt_to_mem() can be
used with minimal ifdeffery.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Remove those as they are not needed anymore.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Move the function at the end of the driver, so we could drop
various forward declarations later. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The private data allocation does not have to be done every time the
NIC is initialized at run time, move the allocation to initialize
function, which means it will be done only once when the driver
starts.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
This combination of functions can be replaced with calloc(),
make it so.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The current code is horribly complex. Both the RX and TX buffer
descriptors are 16 bytes in size, the init block is 32 bytes in
size, so simplify the code such that the entire private data of
the driver are allocated cache aligned and the RX and TX buffer
descriptors are part of the private data.
This removes multiple malloc calls and cache flushes.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Use this macro to fully fill the PCI device ID table. This is mandatory
for the DM PCI support, which checks all the fields.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
All of one PCNET users has this option set, make this default
and drop this config option.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Use struct pcnet_priv all over the place instead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Split the common code from the non-DM code, so it can be reused by
the DM code later. As always, the recv() function had to be split
into the actual receiving part and free_pkt part to fit with the
DM.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The RX/TX DMA descriptor rings are per-device-instance private data,
so move them into the private data.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Instead of doing ethernet device lookup by name every time there
is an MDIO access, pass the driver private data via mdiobus priv
to the MDIO bus accessors.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This patch replaces the various uses of struct eth_device for accessing
device private data with struct eepro100_priv, which is compatible both
with DM and non-DM operation.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is a trick in preparation for adding DM support. By passing in
the PCI BDF into the bus_to_phys()/phys_to_bus() macros and calling
that dev, we can substitute dev with udevice when DM support lands
and do minor adjustment to the macros to support both DM and non-DM
operation. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Drop the inline keyword from the static functions, the compiler has a
much better overview and can decide how to inline those functions much
better.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Those macros depended on specific variable names to be declared
at their usage sites, fix this by adding an argument to those
macros and also protect the argument with braces.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Pull the MII registration code into a separate function. Moreover,
properly free memory in case any of the registration or allocation
functions fail, so this fixes an existing memleak.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Use this macro to fully fill the PCI device ID table. This is mandatory
for the DM PCI support, which checks all the fields.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Move the functions around in the driver to prepare it for DM conversion.
Drop forward declarations which are not necessary anymore. No functional
change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Remove all the remaining use of the 'volatile' keyword, as this is
no longer required. All the accesses which might have needed this
use of 'volatile' have been repaired properly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Add cache invalidation and flushes wherever the DMA descriptors are
written or read, otherwise this driver cannot work reliably on any
systems where caches are enabled.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This code is replicated in the driver thrice almost verbatim, factor
it out into a separate function and clean it up. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The current eepro100 driver accesses its memory mapped registers directly
instead of using the standard I/O accessors. This can cause problems on
some systems as the accesses can get out of order. So convert the direct
volatile dereferences to use the normal in/out macros.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is automated cleanup via checkpatch, no functional change.
./scripts/checkpatch.pl --show-types -f drivers/net/eepro100.c
./scripts/checkpatch.pl --types INDENTED_LABEL -f --fix --fix-inplace drivers/net/eepro100.c
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is automated cleanup via checkpatch, no functional change.
./scripts/checkpatch.pl --show-types -f drivers/net/eepro100.c
./scripts/checkpatch.pl -f --fix --fix-inplace drivers/net/eepro100.c
This fixes all the remaining errors except a couple of comments which
are longer than 80 characters, all the volatile misuse and all the
camelcase, that needs a separate patch.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is automated cleanup via checkpatch, no functional change.
./scripts/checkpatch.pl --show-types -f drivers/net/eepro100.c
./scripts/checkpatch.pl --types INDENTED_LABEL -f --fix --fix-inplace drivers/net/eepro100.c
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is automated cleanup via checkpatch, no functional change.
./scripts/checkpatch.pl --show-types -f drivers/net/eepro100.c
./scripts/checkpatch.pl --types POINTER_LOCATION -f --fix --fix-inplace drivers/net/eepro100.c
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is automated cleanup via checkpatch, no functional change.
./scripts/checkpatch.pl --show-types -f drivers/net/eepro100.c
./scripts/checkpatch.pl --types PARENTHESIS_ALIGNMENT -f --fix --fix-inplace drivers/net/eepro100.c
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is automated cleanup via checkpatch, no functional change.
./scripts/checkpatch.pl --show-types -f drivers/net/eepro100.c
./scripts/checkpatch.pl --types BRACES -f --fix --fix-inplace drivers/net/eepro100.c
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is automated cleanup via checkpatch, no functional change.
./scripts/checkpatch.pl --show-types -f drivers/net/eepro100.c
./scripts/checkpatch.pl --types SPACING -f --fix --fix-inplace drivers/net/eepro100.c
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This code is never enabled, last board that used it was ELPPC which
was removed some 5 years ago, so just remove this code altogether.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
cfb_console driver uses 'vga' console name and we still have board
environments defining this name. Re-use existing DM_VIDEO work-
around for console name to support 'vga' name in stdout environment.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Soeren Moch <smoch@web.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
To enable DM_VIDEO we must decrease binary size to fix build
breakage for some boards, so drop not needed code. Also add
!DM_VIDEO guards which can be later removed when last non DM
users will be converted.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Not all boards use these drivers, so allow to disable them to fix
building boards with U-Boot binary image size restrictions.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Converting some boards to DM_VIDEO results in build breakage due
to increased code size. Make video console specific commands
optional to reduce binary size.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Modify the Freescale ESPI driver to support the driver model.
Also resolved the following problems:
===================== WARNING ======================
This board does not use CONFIG_DM_SPI. Please update
the board before v2019.04 for no dm conversion
and v2019.07 for partially dm converted drivers.
Failure to update can lead to driver/board removal
See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ======================
This board does not use CONFIG_DM_SPI_FLASH. Please update
the board to use CONFIG_SPI_FLASH before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
We generate a number of helper inline functions to make accesses easier.
However not all permutations of each function will be used and clang
will warn about unused ones. Decorate all of them with __maybe_unused
because of this.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
We only call the function omap_hsmmc_get_cfg in the case of OMAP34XX or
when we have to iodelay recalibration. Add guards for these checks as
clang will otherwise warn.
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
In the case of non-DM_GPIO the function get_gpio_index() will never be
called, and clang will warn about this. Move this to be with the other
non-DM code for easier removal later.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
AM654x PG1.0 has a silicon bug that D+ is pulled high after POR, which
could cause enumeration failure with some USB hubs. Disabling the
USB2_PHY Charger Detect function will put D+ into the normal state.
Using property "ti,dis-chg-det-quirk" in the DT usb2-phy node to
enable this workaround for AM654x PG1.0.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
The fix in commit b7adcdd073 has the side-effect that the regulator
will be disabled when requesting the relevant gpio in
regulator_common_ofdata_to_platdata() and enabled in
regulator_pre_probe() when the regulator was already enabled.
This leads to a short interruption in the 3.3V power to the PCIe
slot on the firefly-rk3399 which makes an ADATA SX8000NP NVMe SSD
unhappy.
Fix this by setting the GPIOD_IS_OUT_ACTIVE flag again when the
'regulator-boot-on' property is set, but check for this property
explicitly instead of relying on the "boot_on" member of
the uclass platdata.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Tested-by: Patrice Chotard <patrice.chotard@st.com>
Unsupported voltage on voltage switch is not an error, do not
print error message in such a case. This happens e.g. if the
eMMC is already in 1V8 mode or when testing 1V2 mode operation
on systems which only do 3V3/1V8 switching.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The 3V3/1V8 switching could never have worked on any of the iMXes
ever since 51313b49f2 ("mmc: fsl_esdhc: support SDR104 and HS200"),
because that commit uses priv->vqmmc_dev when switching voltages on
mode switch, while local vqmmc_dev in probe to store the regulator
pointer. Those are two different variables with the same name. So
the priv->vqmmc_dev was always NULL and thus voltage switch between
modes never really suceeded.
Fix this by assigning priv->vqmmc_dev with value of the vqmmc_dev
in probe.
Fixes: 51313b49f2 ("mmc: fsl_esdhc: support SDR104 and HS200")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
- Rename DT compatible name
- Remove uneccessary if-statement to support 8-bit buswidth
- Remove redundant error msg
- Use symbolic constants in switch statement
Signed-off-by: Arthur Li <arthur.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Tom Rini <trini@konsulko.com>
When eSDHC operates at 3.3v, damage can accumulate in an internal
level shifter at a higher than expected rate. The faster the interface
runs, the more damage accumulates. This issue now is found on LX2160A
eSDHC1 for only SD card.
The hardware workaround is recommended to use an on-board level shifter
that is 1.8v on SoC side and 3.3v on SD card side.
For boards without hardware workaround, this option could be enabled,
ensuring 1.8v IO voltage and disabling eSDHC if no card.
This option assumes no hotplug, and u-boot has to make all the way to
to linux to use 1.8v UHS-I speed mode if has card.
If you do not want the workaround for better user experience, of course
you can choose to not select it running eSDHC in unsafe mode.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Update the firmware to improve compatibility for none-intel USB
host controller. The more information is as following.
The device has auto-installed driver feature - via switch CD-ROM/NIC
mode. But in some corner cases, it would switch to CD-ROM unexpected.
This issue results in Lan Function Disabled.
While USB PHY transits to P3 from P0 due to the absent of transmitter
control, it would issues undefined signal to its link partner.
Some Down Stream Port misidentify the undefined signal as wakeup
signal. So the link state will not keep in suspend even the system
is idle.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Cleanup this driver to use dt in U-boot and static platdata in SPL.
This requires the following steps:
1. Move all platdata assignment from probe() to ofdata_to_platdata().
This function is only called in U-boot.
2. Replicate all the platdata assignment being done in
ofdata_to_platdata() in the omapl138 board file. This data is used in
the SPL case where SPL_OF_CONTROL is not enabled.
3. Remove SPL_OF_CONTROL and related configs from omapl138_lcdk_defconfig
This cleanup effectively reverts 3ef94715cc ('mmc: davinci: fix mmc boot in SPL')
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
change to how sequence numbers are assigned to devices
minor fixes and improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl7kQ4kRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZrvAgAqc/TEj7QHPyW9rQSl8h65MXK93qRsnZo
4segKEtK0Rmv0S2VfmPCwujsDFl5gZUNt+rXD/l7F0a4Wzx4eYgYrEXOYsXs/ZHP
jjGrcbvO4Qkx3QzjMqqoUiQqeCgNQ9XIre8F+1NmZeQ2bFtPKbJXtXKYTcMI1wSW
PhRGbbsTnKNKC0dL0nLFG6+NC/sk6xRqMx28Ip38FTrQL+Uh67LZFpLkY3yuHo/1
CVhCw+7Aov0I6tDrdKrngjFqXRSoTsuOhavSFoW9U6llqDL7FIC6aoRo7x24lSJN
VFTRpXPmNHeslE6NHEOQs9elFpbxXR34te3k4p74rFuX/J/490UaYA==
=172C
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-12jun20' of git://git.denx.de/u-boot-dm into next
patman improvements to allow it to work with Zephyr
change to how sequence numbers are assigned to devices
minor fixes and improvements
Do not re-read the HW address from the EEPROM on every start of
transfer, otherwise the user will not be able to adjust ethaddr
as needed. Read the address only once, when the card is detected.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Use this macro to fully fill the PCI device ID table. This is mandatory
for the DM PCI support, which checks all the fields.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Split the driver into common and non-DM functionality, so that the
DM support can later re-use the common code, while we retain the
non-DM code until all the platforms are converted.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Instead of always calling rtl8139_eeprom_delay() with priv->ioaddr,
call it with priv and let the function access priv->ioaddr. This
reduces code duplication and has no impact, since the compiler will
inline this as needed anyway.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Introduce rtl8139_pdata, which is a super-structure around eth_device
and tracks per-device state, here the device IO address, PCI BDF, RX
and TX ring position. Pass this structure around instead of the old
non-DM eth_device in preparation for DM conversion.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
These macros depended on the dev variable being declared wherever
they were used. This is wrong and will not work with DM anyway, so
pass only the PCI BFD into these macros, which fixes the dependency
and prepares them for DM support as well.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Replace the use of custom static ioaddr variable with common dev->iobase,
no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Replace malloc()+memset() combination with calloc(), no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Pull the device name setting into a separate function, as this
will be shared between DM/non-DM variants.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Add the DP8382X generic PHY registration to the TI PHY init file.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
ti_phy_init function was allocated to the DP83867 PHY. This function
name is to generic for a specific PHY. The function can be moved to a
TI specific file that can register all TI PHYs that are defined in the
defconfig. The ti_phy_init file will contain all TI PHYs initialization
so that only phy_ti_init can be called from the framework.
In addition to the above the config flag for the DP83867 needs to be changed
in the Kconfig and dependent defconfig files. The config flag that was
used for the DP83867 was also generic in nature so a more specific
config flag for the DP83867 was created.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
There are devices accesible through mdio clause-45, such as
retimers, that do not have PMA or PCS blocks.
This patch adds MDIO_MMD_VEND1 on the list of device addresses
where phyid is searched. Previous order of devices was kept.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
This is a WAR for DHCP failure after rebooting from the L4T kernel. The
r8169.c kernel driver is setting bit 19 of the rt816x HW register 0xF0,
which goes by FuncEvent and MISC in various driver source/datasheets.
That bit is called RxDv_Gated_En in the r8169.c kernel driver. Clear it
here at the end of probe to ensure that U-Boot can get an IP assigned
via DHCP.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Linux commit 232ba3a51cc2 ('net: phy: Micrel KSZ8061: link failure after
cable connect') implements a fix for the above errata.
This patch replicates that errata fix in an ksz8061 specific init routine.
Signed-off-by: Bryan O'Donoghue <bod@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If there are aliases for an uclass, set the base for the "dynamically"
allocated numbers next to the highest alias.
Please note, that this might lead to holes in the sequences, depending
on the device tree. For example if there is only an alias "ethernet1",
the next device seq number would be 2.
In particular this fixes a problem with boards which are using ethernet
aliases but also might have network add-in cards like the E1000. If the
board is started with the add-in card and depending on the order of the
drivers, the E1000 might occupy the first ethernet device and mess up
all the hardware addresses, because the devices are now shifted by one.
Also adapt the test cases to the new handling and add test cases
checking the holes in the seq numbers.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Alex Marginean <alexandru.marginean@nxp.com>
Tested-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Michal Simek <michal.simek@xilinx.com> [on zcu102-revA]
It is possible to specify a device tree node for an USB device. This is
useful if you have a static USB setup and want to use aliases which
point to these nodes, like on the Raspberry Pi.
The nodes are matched against their hub port number, the compatible
strings are not matched for now.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
In regmap_raw_{read,write}_range(), offsets are checked to make sure
they aren't out of range. But this check happens _after_ the address is
mapped from physical memory. Input should be sanity-checked before using
it. Mapping the address before validating it leaves the door open to
passing an invalid address to map_physmem(). So check for out of range
offsets _before_ mapping them.
This fixes a segmentation fault in sandbox when -1 is used as an offset
to regmap_{read,write}().
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Now all boards which are using davinci SPI driver
have moved to SPL_DM so drop the unneeded non-dm code.
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
atmel_spi.h has register offsets, and atmel_spi_slave
structure, move it into .c file for better readability
and drop atmel_spi.h
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
atmel spi driver now accessible only when DM_SPI enabled.
So, remove nondm code.
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
- Deadline for DM migration already passed by months.
- Sent couple of zap patches and
- No response on dm conversation
hence removed the driver.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Order the macros, private structures and simple functions
in a proper way to have more code readability.
No functionality changed.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Deadline for DM migration already passed by months
and no response on full dm conversation hence removed
the nondm code.
Note: Look like there is no user for nondm code
for this driver.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add the missing Kconfig dependency and let VIRTIO_RNG default to yes.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Debug console is the part of serial driver in the same file. It means to be
able to enable debug console you also need to enable driver itself.
That's why add all dependecies and list only debug consoles which are
enabled based on driver selection to avoid compilation error when user
asks for certain debug console but driver is not enable for it.
Error:
aarch64-linux-gnu-ld.bfd: common/built-in.o: in function `putc':
/home/monstr/data/disk/u-boot/common/console.c:513: undefined reference to `printch'
aarch64-linux-gnu-ld.bfd: common/built-in.o: in function `puts':
/home/monstr/data/disk/u-boot/common/console.c:563: undefined reference to `printch'
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Fix ns16550 dependency, add ZYNQ_SERIAL, change S5P]
Signed-off-by: Tom Rini <trini@konsulko.com>
The symbol "CONFIG_ARM_DCC" is used to control building
drivers/serial/arm_dcc.c. Provide a simple Kconfig entry for this.
Cc: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Tom McLeod <tom.mcleod@opalkelly.com>
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
When an eTSEC is configured to use TBI, configuration of the
TBI is done through the MIIM registers for that eTSEC.
For example, if a TBI interface is required on eTSEC2, then
the MIIM registers starting at offset 0x2_5520 are used to
configure it.
Fixes: 9a1d6af55e ("net: tsec: Add driver model ethernet support")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The current code accesses eTSEC registers using physical
address directly, it's not correct, though no problem on
current platforms. It won't work on platforms, which does
not support 1:1 virtual-physical address map.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Allow the MDIO devices to be probed based on the device tree.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
U-Boot ethernet works with FSBL flow where releasing ethernet clock
reset is part of FSBL itself but with the SPL, We need to release
ethernet clock reset explicitly for U-Boot proper. With this change
Release ethernet clock reset code in FSBL might not be needed or
unaffected.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Release ddr clock reset once clock is initialized
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Added clock enable and disable functions in prci ops
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Add driver for fu540 to support ddr initialization in SPL.
This driver is based on FSBL
(https://github.com/sifive/freedom-u540-c000-bootloader.git)
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Added a misc driver to handle OTP memory in SiFive SoCs.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
A compilation error appears when QE is compiled with DM_ETH
enabled:
drivers/qe/uec.c: In function 'init_phy':
drivers/qe/uec.c:425:28: error: dereferencing pointer to incomplete type 'struct eth_device'
uec = (uec_private_t *)dev->priv;
^~
drivers/qe/uec.c: In function 'uec_initialize':
drivers/qe/uec.c:1357:43: error: invalid application of 'sizeof' to incomplete type 'struct eth_device'
dev = (struct eth_device *)malloc(sizeof(struct eth_device));
^~~~~~
The patch disables CONFIG_QE when CONFIG_DM_ETH is set.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This config option depends on EXT4 support.
If Ext4 write capability is not selected, it generate write error messages
and is unable to maintain boot counter.
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com>
This is defined in the asm/cache.h header file. Update this header file to
include it so it gets the same value consistently across U-Boot.
This fixes 'usb host' on omapl138_lcdk.
Fixes: 90526e9fba ("common: Drop net.h from common header")
Reported-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present this logic does not work on link and samus, since their SPI
controller is not a PCI device, but a child of the PCH.
Unfortunately, fixing this involves a lot of extra logic. Still, this was
requested in the review of the fix-up patch, so here it is.
Fixes: 92842147c3 ("spi: ich: Add support for get_mmap() method")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com> (on Intel minnowmax)
The H6 EMAC is very similar to the H3 variant, except that it uses the
same pinmux as R40. Add support for it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
While the R40 uses a different register for EMAC clock configuration
than other chips, the register has a very similar layout. Reuse the
existing bitfield definitions in this file, since they match.
This allows the driver to compile on the H6 platform, where the
CCM_GMAC_CTRL definitions are not present.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
dm_spi_slave_platdata used in sf_probe for printing
plat->cs value and there is no relevant usage apart
from this.
We have enough debug messages available in SPI and SF
areas so drop this plat get and associated bug statement.
Cc: Simon Glass <sjg@chromium.org>
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Currently spi-nor code is assigning _write ops for SST
and other flashes separately.
Just call the sst_write from generic write ops and return
if SST flash found, this way it avoids the confusion of
multiple write ops assignment during the scan and makes
it more feasible for code readability.
No functionality changes.
Cc: Simon Glass <sjg@chromium.org>
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The get_sw_write_prot API is used to get the write-protected
bits of flash by reading the status register and other wards
it's API for reading register bits.
1) This kind of requirement can be achieved using existing
flash operations and flash locking API calls instead of
making a separate flash API.
2) Technically there is no real hardware user for this API to
use in the source tree.
3) Having a flash operations API for simple register read bits
also make difficult to extend the flash operations.
4) Instead of touching generic code, it is possible to have
this functionality inside spinor operations in the form of
flash hooks or fixups for associated flash chips.
Considering all these points, this patch drops the get_sw_write_prot
and associated code bases.
Cc: Simon Glass <sjg@chromium.org>
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Use CONFIG_IS_ENABLED to prevent ifdef in sf_probe.c
Cc: Simon Glass <sjg@chromium.org>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
sh_spi driver is deprecated, no active updates and
no board user, hence dropped the same.
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
CF_SPI kconfig option defined twice with DM_SPI
and non DM_SPI.
Drop the non DM_SPI side kconfig definition.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
- Fix mmc of path after syncfrom kernel dts;
- Add dwc3 host support with DM for rk3399;
- Add usb2phy and typec phy for rockchip platform;
- Migrate board list doc to rockchip.rst;
- Add rk3399 Pinebook Pro board support;
- Update dram_init in board_init and add memory node in SPL;
Including the assembler headers before including common.h etc leads to
compilation errors upon MIPS64 based platforms using OF_LIVE. This
patch reorders the include files to the "correct" oder.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
We have changed to use dwc3 generic driver for usb3.0 host, so the
legacy Rockchip's xHCI driver is not needed, and drop it.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
RK3399 Type-C PHY is required that must hold whole USB3.0 OTG controller
in resetting to hold pipe power state in P2 before initializing the PHY.
This commit fixed it and added device compatible for rockchip platform.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Print the error code if the regulator enable fails, otherwise the error
message is rather useless and confusing.
Signed-off-by: Marek Vasut <marex@denx.de>
The regulator-fixed would return -ENOSYS when enabled/disabled,
because this operation is not supported, but this is not an error
e.g. on systems where the VBUS cannot be controlled, so if this
is the error code reported by the regulator core, consider it a
success and continue.
Signed-off-by: Marek Vasut <marex@denx.de>
Although I think it never occurs, the code doesn't make sense, because
it may allow to assign an IN endpoint to ss->ep_out.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Let move 8/16-bit UTMI+ interface initialization into DWC3 core init
that is convenient for both DM_USB and u-boot traditional process.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
By default when core sees any transaction error (CRC or overflow) it
replies with terminating retry ACK (Retry=1 and Nump == 0).
Enabling this Auto Retry feature in controller will make the core send
a non-terminanting ACK upon such transaction errors. That is, ACK TP
with Retry=1 and Nump != 0.
Doing so will give controller a chance to recover from transient error
conditions.
Reference from below Linux commit,
commit <b138e23d3dff> ("usb: dwc3: core: Enable AutoRetry feature
in the controller")
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This patch adds a quirk to disable USB 2.0 MAC linestate check
during HS transmit. Refer the dwc3 databook, we can use it for
some special platforms if the linestate not reflect the expected
line state(J) during transmission.
When use this quirk, the controller implements a fixed 40-bit
TxEndDelay after the packet is given on UTMI and ignores the
linestate during the transmit of a token (during token-to-token
and token-to-data IPGAP).
On some rockchip platforms (e.g. rk3399), it requires to disable
the u2mac linestate check to decrease the SSPLIT token to SETUP
token inter-packet delay from 566ns to 466ns, and fix the issue
that FS/LS devices not recognized if inserted through USB 3.0 HUB.
Reference from below Linux commit,
commit <65db7a0c9816> ("usb: dwc3: add disable u2mac linestate
check quirk")
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a quirk to clear the GUSB2PHYCFG.U2_FREECLK_EXISTS bit,
which specifies whether the USB2.0 PHY provides a free-running
PHY clock, which is active when the clock control input is active.
Refer to commit 27f83eeb6b42("usb: dwc3: add dis_u2_freeclk_exists_quirk")
in Linux Rockchip Kernel.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Add a quirk to clear the GUSB2PHYCFG.ENBLSLPM bit, which controls
whether the PHY receives the suspend signal from the controller.
Refer to commit ec791d149bca("usb: dwc3: Add dis_enblslpm_quirk")
in Linux Kernel.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Add USB TYPEC PHY driver for rockchip platform.
Referenced from Linux TypeC PHY driver, currently
supporting usb3-port and dp-port need to add it
in the future.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add Rockchip USB2PHY driver with initial support.
This will help to use it for EHCI controller in host
mode, and USB 3.0 controller in otg mode.
More functionality like charge, vbus detection will
add it in future changes.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable/Disable TCPHY clock for rk3399 platform.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Due to v5.7-rc1 sync the SD controller nodes in rk3399.dtsi
have SCLK_UPHY0_TCPDCORE, SCLK_UPHY1_TCPDCORE assigned-clocks
which are usually required for Linux and don't require to
handle them in U-Boot.
assigned-clocks = <&cru SCLK_UPHY0_TCPDCORE>;
assigned-clocks = <&cru SCLK_UPHY1_TCPDCORE>;
So, mark them as empty in clock otherwise device probe on
those typec phy driver would fail.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable/Disable the USB2PHY clk for rk3399.
CLK is clear in enable and set in disable functionality.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The vpcie*-supply properties are optional and these are absent on
boards like the ROCKPro64 and Firefly RK3399 where the voltage is
supplied by always-on regulators that are already enabled upon
boot. Make these regulators optional and properly check their
presence before attempting to enable them.
Makes PCIe work on un U-Boot on the boards mentioned above.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl>
Actual eMMC get_clk register is clksel_con22 instead of
clksel_con21.
Fix it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Because of this commit :
5ae84860b0 ("misc: i2c_eeprom: verify that the chip is functional at probe()")
at probe time, each eeprom is tested for read at offset 0.
The Atmel AT24MAC402 eeprom has different mapping. One i2c slave address is
used for the lower 0x80 bytes and another i2c slave address is used for the
upper 0x80 bytes. Because of this basically the i2c master sees 2 different
slaves. We need the upper bytes because we read the unique MAC address from
this EEPROM area.
However this implies that our slave address will return error on reads
from address 0x0 to 0x80.
To solve this, implemented an offset field inside platform data that is by
default 0 (as it is used now), but can be changed in the compatible table.
The probe function will now read at this offset and use it, instead of blindly
checking offset 0.
This will fix the regression noticed on these EEPROMs since the commit
abovementioned that introduces the probe failed issue.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
When compiling with -Wtype-limits we see this error:
drivers/i2c/i2c-uclass.c: In function ‘i2c_deblock_gpio_loop’:
drivers/i2c/i2c-uclass.c:517:21: error: comparison of
unsigned expression >= 0 is always true [-Werror=type-limits]
517 | while (scl_count-- >= 0) {
|
Don't loop forever.
Fixes: 1f746a2c82 ("i2c: Make deblock delay and SCL clock configurable")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If the device doesn't return a version that means the device is
non-functional.
The dw_i2c_regs had invalid offsets for the version field. I got the
correct value from the DesignWare databook. It also matches what the
Picasso PPR says.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Tested on chromebook_coral:
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we still have pre-driver-model code in this driver and it makes
things a bit confusing. In particular calc_bus_speed() is called with priv
as NULL if not using driver model.
This results in spk_cnt and comp_param1 being read from an invalid address
if not using driver model. For comp_param1 this may not cause problems if
reading from addresses close to 0 happens to be allowed, as high speed is
only supported by DM code. But spk_cnt is subsequently used to calculate
the bus periods and so this may cause problems (e.g. on spear600 board
which has not been migrated yet).
Add a new parameter regs parameter to calc_bus_speed() and add more
comments to this function and to _dw_i2c_set_bus_speed(), which calls it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add support for new Kioxia products.
The new Kioxia products support program load x4 command, and have
HOLD_D bit which is equivalent to QE bit.
Signed-off-by: Yoshio Furuyama <ytc-mb-yfuruyama7@kioxia.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/aa69e455beedc5ce0d7141359b9364ed8aec9e65.1584949601.git.ytc-mb-yfuruyama7@kioxia.com
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The suffix was changed from "G" to "J" to classify between 1st generation
and 2nd generation serial NAND devices (which now belong to the Kioxia
brand).
As reference that's
1st generation device of 1Gbit product is "TC58CVG0S3HRAIG"
2nd generation device of 1Gbit product is "TC58CVG0S3HRAIJ".
The 8Gbit type "TH58CxG3S0HRAIJ" is new to Kioxia's serial NAND lineup and
the prefix was changed from "TC58" to "TH58".
Thus the functions were renamed from tc58cxgxsx_*() to tx58cxgxsxraix_*().
Signed-off-by: Yoshio Furuyama <ytc-mb-yfuruyama7@kioxia.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/0dedd9869569a17625822dba87878254d253ba0e.1584949601.git.ytc-mb-yfuruyama7@kioxia.com
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
It is possible that users of generic_phy_*() APIs may pass a valid
struct phy pointer but phy->dev can be NULL, leading to NULL pointer
deference in phy_dev_ops().
So call generic_phy_valid() to verify that phy and phy->dev are both
valid.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Convert CONFIG_KS8851_MLL and CONFIG_KS8851_MLL_BASEADDR to Kconfig
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Add support for U-Boot DM and DT probing.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Instead of reading out the entire FIFO and possibly overwriting U-Boot
memory, read out one packet per recv call, pass it to U-Boot network
stack, and repeat. It is however necessary to cache RXFC value, because
reading that one out clears it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Split network handling functions into non-DM specific parts and
common code in preparation for conversion to DM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Introduce a private data structure for this driver with embedded
struct eth_device and pass it around. This prepares the driver to
work with both DM and non-DM systems.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Fix various checkpatch complaints.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
There is only one chip ID in the table of chip IDs for this chip.
Read out the chip ID instead and mask off the last "revision" bit
to check the chip ID, this works for all chips in the family. Then
drop the chip ID passing around.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The packet status and length information should be extracted from the
FIFO per-packet. Adjust the code such that it reads the packet meta
data and then the packet afterward, if applicable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Most of the entries in the structure are useless, remove them. Inline
the rest of uses where applicable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Per KS8851-16MLL, the RXQCR is a 16bit register. Use 16bit accessors
to it consistently and drop the ks_wrreg8() function altogether, as
it is not used anymore.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The cached RXQCR value is never updated, remove the cache and just use
the bits in the cache directly in the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Replace combination of malloc()+memset() with calloc() as the behavior
is exactly the same and the amount of code is reduced. Moreover, remove
printf() in the fail path, as it is useless, and return proper -ENOMEM
return code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXse5FQ4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXPBfAJ9KNsTM95wQTc/E2zL5hfd58sS3dwCePgugeAkj
+NCwAgKCABJFdS/yBK0=
=w9C+
-----END PGP SIGNATURE-----
Merge tag 'imx8qxp-fixes' of https://gitlab.denx.de/u-boot/custodians/u-boot-video
- Fix i.MX8QXP boot hang when getting CPU temperature
The phy_bulk pointer *usb_phys is used before allocated,
fix it by using a phy_bulk variable instead in
xhci_dwc3_platdata struct
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
The omap3.dtsi file shows the usbhshost node with two sub-nodes
for ohci and ehci. This patch file creates the usbhshost, and
pulls the portX-mode information. It then locates the EHCI
sub-node, and initializes the EHCI controller with the info
pulled from the usbhshost node.
There is still more to do since there isn't an actual link
between the 'phys' reference and the corresponding phy driver,
and there is no nop-xceiv driver yet.
In the meantime, the older style reference to
CONFIG_OMAP_EHCI_PHYx_RESET_GPIO is still needed to pull
the phy out of reset until the phy driver is completed and the
phandle reference is made.
Signed-off-by: Adam Ford <aford173@gmail.com>
Yes, it is possible to have a dedicated UCLASS PHY driver
for this Rockchip PCIe PHY but there are some issues on
Generic PHY framework to support the same.
The Generic PHY framework is unable to get the PHY if
the PHY parent is of a different uclass.
Say if we try to get the PCIe PHY then the phy-uclass
will look for PHY in the first instance if it is not
in the root node it will try to probe the parent by
assuming that the actual PHY is inside the parent PHY
of UCLASS_PHY. But, in rk3399 hardware representation
PHY like emmc, usb and pcie are part of syscon which
is completely a different of UCLASS_SYSCON.
Example:
grf: syscon@ff770000 {
compatible = "rockchip,rk3399-grf", "syscon", "simple-mfd";
reg = <0x0 0xff770000 0x0 0x10000>;
#address-cells = <1>;
#size-cells = <1>;
pcie_phy: pcie-phy {
compatible = "rockchip,rk3399-pcie-phy";
clocks = <&cru SCLK_PCIEPHY_REF>;
clock-names = "refclk";
#phy-cells = <1>;
resets = <&cru SRST_PCIEPHY>;
drive-impedance-ohm = <50>;
reset-names = "phy";
status = "disabled";
};
};
Due to this limitation, this patch adds a separate PHY
driver for Rockchip PCIe. This might be removed in future
once Generic PHY supports this limitation.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Suniel Mahesh <sunil@amarulasolutions.com> #roc-rk3399-pc
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add Rockchip PCIe controller driver for rk3399 platform.
Driver support Gen1 by operating as a Root complex.
Thanks to Patrick for initial work.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Suniel Mahesh <sunil@amarulasolutions.com> #roc-rk3399-pc
Enable/Disable the PCIEPHY clk for rk3399.
CLK is clear in both enable and disable functionality.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Suniel Mahesh <sunil@amarulasolutions.com> #roc-rk3399-pc
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Yes, most of the high speed peripheral clocks
in rk3399 enabled by default.
But it would be better to handle them via clk
enable/disable API for handling proper reset
conditions like 'usb reset' over command line.
So, enable USB, GMAC clock via enable/disable ops.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Suniel Mahesh <sunil.m@amarulasolutions.com> # roc-rk3399-pc
Tested-by: Suniel Mahesh <sunil@amarulasolutions.com> #roc-rk3399-pc
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Should initialization of pdata values have failed for some reason,
we end up in endless loop when getting the CPU temperature value
and can not boot. Check alert value in pdata and only retry reading
temperature if alert value is not zero. Also shorten the temperature
info string.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This fixes getting DT alert and critical pdata values in imx_scu_thermal
driver. On i.MX8QXP using not initialized alert pdata value resulted in
boot hang and endless loop outputting:
CPU Temperature (47200C) has beyond alert (0C), close to critical (0C) waiting...
While at it, preset CPU type values once to avoid multiple calls
of device_is_compatible() for same property.
Fixes: 3ee6ea443e ("cpu: imx_cpu: Print the CPU temperature for iMX8QM A72")
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
CPU type and rate detection is broken, for A35 cpu we get A53:
...
sc_pm_get_clock_rate: resource:0 clk:2: res:3
Could not read CPU frequency: -22
CPU: NXP i.MX8QXP RevB A53 at 0 MHz at 47C
Fixes: 55bc96f3b6 ("cpu: imx8: fix get core name and rate")
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
[ Linux commit 9afbe7c0140f663586edb6e823b616bd7076c00a ]
If the write protect signal from this IP is connected to the NAND
device, this IP can handle the WP# pin via the WRITE_PROTECT
register.
The Denali NAND Flash Memory Controller User's Guide describes
this register like follows:
When the controller is in reset, the WP# pin is always asserted
to the device. Once the reset is removed, the WP# is de-asserted.
The software will then have to come and program this bit to
assert/de-assert the same.
1 - Write protect de-assert
0 - Write protect assert
The default value is 1, so the write protect is de-asserted after
the reset is removed. The driver can write to the device unless
someone has explicitly cleared register before booting the kernel.
The boot ROM of some UniPhier SoCs (LD4, Pro4, sLD8, Pro5) is the
case; the boot ROM clears the WRITE_PROTECT register when the system
is booting from the NAND device, so the NAND device becomes read-only.
Set it to 1 in the driver in order to allow the write access to the
device.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This CONFIG option is only used in denali_spl.c
Move it close to SPL_NAND_DENALI, and make it depend on SPL_NAND_DENALI.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
- Add DM_ETH support for lx2160aqds, ls2080aqds, ls1088aqds
- QSI related fixes on ls1012a, ls2080a, ls1046a, ls1088a, ls1043a based
platforms
- Bug-fixes/updtaes related to ls1046afrwy, fsl-mc, msi-map property
This driver is safe to use in SPL without relocation. Denying
DM_FLAG_PRE_RELOC prevents its usability for verifying the main U-Boot
or other artifacts from the SPL unless needless enabling the full driver
set (SPL_OF_PLATDATA).
Fixes: 17e1174085 ("drivers: crypto: rsa_mod_exp: avoid DM_FLAG_PRE_RELOC")
CC: Heinrich Schuchardt <xypron.glpk@gmx.de>
CC: Marek Vasut <marex@denx.de>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
The DPC fixup for MAC address and enet_if is not made if
/board/ports node is missing in DPC file.
Add /board/ports or /ports nodes if them are missing.
Signed-off-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
Reviewed-by: Ioana Ciornei <Ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Similarly to iommu-map, the msi-map property must also be fixed up
in the device tree, in order for the icid -> streamid translation
be possible in the MSI case as well.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Diana Craciun <diana.craciun@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Bus callback functions for read/write/reset need to be set only for
DM_ETH, moving endif a bit lower.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
This requires quite a few header-file additions.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should not be using typedefs and these make it harder to use
forward declarations (to reduce header file inclusions). Drop the typedef.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is bad practice to include common.h in other header files since it can
bring in any number of superfluous definitions. It implies that some C
files don't include it and thus may be missing CONFIG options that are set
up by that file. The C files should include these themselves.
Update some header files in arch/arm to drop this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this uncommon header out of the common header.
Fix up some style problems in flash.h while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Virtually all callers of this function do the rounding on their own.
Some do it right, some don't. Instead of doing this in each caller,
do the rounding in efi_add_memory_map(). Change the size parameter
to bytes instead of pages and remove aligning and size calculation in
all callers.
There is no more need to make the original efi_add_memory_map() (which
takes pages as size) available outside the module. Thus rename it to
efi_add_memory_map_pg() and make it static to prevent further misuse
outside the module.
Signed-off-by: Michael Walle <michael@walle.cc>
Add missing comma in sunxi_display.c.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Have this symbol follow the pattern of all other such symbols.
This patch also removes a TODO from the code.
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Have this symbol follow the pattern of all other such symbols.
This patch removes a TODO from the code.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
- stm32mp1: add command stm32prog
- stm32mp1: several board and arch updates
- stm32mp1: activate data cache in SPL and before relocation
- Many improvment for AV96 board and DHCOR SoM
(add new defconfig, DDR3 coding on DHCOR SoM, split between board and SOM
Synchronize DDR setttings on DH SoMs, setting for I2C EEPROM)
- clk: stm32mp1: fix CK_MPU calculation
- DT alignment of stm32mp1 device tree with Linux 5.7-rc2
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl69FWMACgkQ4rK92eCq
k3Vy9wgAmFLZ+u2C87A9Cs8i73QX/hs9TsjTJJPxsQWy3bOILgw8ZqBtzqD0qPvc
Mpqq7UEIZ17OW/lZCi3hqC0nGj7bT3N9rDpUQfu5Voq3GoO80yZqvCQU04AXGGpW
Aj0fjI5a6JRxQfR7XVoNw7UXPDUrDlchvBDR1GMK4cj4Sw/B+pXNDjkoJ1UWbxG6
INDgQQKhOCdMzbIsMLiUe4zkT6E8ADI0eJzgti3kWBzrdkwXZg40iEJu/MbMPRKE
Y22QZ6EkEMFTVYeCPXLU8keo4UbBIKDXWmVDbDeDbNa0QrKZ2IZ0TijajWeMWxZV
Q9J7JgpSchWcVB14vYNx+HXPUHANTA==
=bhlu
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200514' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- stm32mp1: migrate MTD and DFU configuration in Kconfig
- stm32mp1: add command stm32prog
- stm32mp1: several board and arch updates
- stm32mp1: activate data cache in SPL and before relocation
- Many improvment for AV96 board and DHCOR SoM
(add new defconfig, DDR3 coding on DHCOR SoM, split between board and SOM
Synchronize DDR setttings on DH SoMs, setting for I2C EEPROM)
- clk: stm32mp1: fix CK_MPU calculation
- DT alignment of stm32mp1 device tree with Linux 5.7-rc2
- sync RPi4's env size with other RPi configs
- add kconfig option to reserver more pages in the EFI mem map
- add support for SDMA which is used by RPi4
- fix corner case boot bug for RPi3 32-bit
-----BEGIN PGP SIGNATURE-----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=66oV
-----END PGP SIGNATURE-----
Merge tag 'rpi-next-2020.07' of https://gitlab.denx.de/u-boot/custodians/u-boot-raspberrypi
- fix phy configuration for RPi4's bcmgenet
- sync RPi4's env size with other RPi configs
- add kconfig option to reserver more pages in the EFI mem map
- add support for SDMA which is used by RPi4
- fix corner case boot bug for RPi3 32-bit
When the CK_MPU used PLL1_MPUDIV, the current rate is
wrong. The clock must use stm32mp1_mpu_div as a shift
value. Fix the check value used to enter PLL_MPUDIV.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Change the mmc displayed name in U-Boot for stm32_sdmmc2 driver to
“STM32 SD/MMC”.
This stm32_sdmmc2 driver is for version 2 of the ST HW IP SDMMC but the
displayed name "STM32 SDMMC2" is confusing for user, between the
instance of SDMMC and the device identifier of MMC.
For example on EV1 board, we have:
STM32MP1> mmc list
STM32 SDMMC2: 0 (SD)
STM32 SDMMC2: 1 (eMMC)
Changed to more clear:
STM32MP1> mmc list
STM32 SD/MMC: 0 (SD)
STM32 SD/MMC: 1 (eMMC)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The GPIO support is needed in SPL to managed the SD cart detect
used on stm32mp157c-ev1 and dk2 board.
So this patch activates the associated code in stm32_gpio.c.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a function g_dnl_set_product to change the Product string used in USB
enumeration in any command based on download gadget.
If the function is called with NULL pointer, the product string is set to
the default value (product[] = "USB download gadget").
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support for multiple DRAM configuration subnodes, while retaining
the support for a single flat DRAM configuration node. This is useful
on systems which can be manufactured in multiple configurations and
where the DRAM configuration can be determined at runtime.
The code is augmented by a function which can be overridden on board
level, allowing a match on the configuration node name, very much like
the fitImage configuration node name matching works. The default match
is on the single top-level DRAM configuration, if matching on subnodes
is required, then this board_stm32mp1_ddr_config_name_match() must be
overridden.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
HSDK and HSDK-4xD clock trees are slightly different.
commit 1dfb2ec0d7 ("ARC: HSDK: CGU: add support for timer clock")
introduce regression for HSDK board cause crash when setting
tunnel clock. Fix that.
Fixes: 1dfb2ec0d7 ("ARC: HSDK: CGU: add support for timer clock")
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We don't want to allow change some clocks, i.e. DDR clock.
So allow to have set_clock to be unset in clock map.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
The clock trees of HSDK and HSDK-4xD vary so we need to prepare
CGU driver for multiple clock maps support.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
* constify clocks config data where is possible
* use more appropriate data types for clocks config
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Drop creg_div_oft offset as it doesn't vary (due to it is used for
CPU PLL only).
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
hsdk_axi_clk_cfg and hsdk_tun_clk_cfg clock divider structures
and functions for their processing are almost the same so
merge them to avoid code duplication.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
If CONFIG_MMC_SDHCI_SDMA is enabled but the HW could not support it,
we no longer error out. Instead we do not enable it in the host.
Change the output from printf to debug as this isn't an error but only
additional information now.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
If Host controller doesn't support SDMA, it doesn't need to return
error. Because it can be worked with PIO mode.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Use phys2bus macro when dma address is accessed.
Some targets need to use pyhs2bus macro. (e.g, RPI4)
After applied it, SDMA mode can be used.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
We cannot rely on a parent bus that needs to be probed, until we know that
it is probed. That means that code in the ofdata_to_platdata() method
cannot rely on the parent bus being probed.
Move the ofdata code in the two serial drivers into a probe() method.
This fixes serial output on rpi_3b_32b with the following config.txt
options:
enable_uart=1
gpu_freq=250
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
As per Linux's driver, ID_MODE_DIS is only set when the PHY interface is
RGMII. Don't enable it for the rest of setups.
This has been seen to misconfigure RPi4's PHY when booting Linux.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Xilinx Versal platform uses dwc3 and hence its compatible string
needs to be added to dwc3 glue ids.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add a quirk to clear the GUSB3PIPECTL.DELAYP1TRANS bit,
which specifies whether disable delay PHY power change
from P0 to P1/P2/P3 when link state changing from U0
to U1/U2/U3 respectively.
Reference from below Linux commit,
commit <00fe081dc3a3> ("usb: dwc3: add dis_del_phy_power_chg_quirk")
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Handle the GPIOD_OPEN_DRAIN & GPIOD_OPEN_SOURCE flags to emulate open drain
and open source by setting the GPIO line as input depending on the
requested value.
The behaviour is taken from the Linux gpiolib.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On i.mx7ulp EVK board, we use MX25R6435F NOR flash, add its parameters
and IDs to flash parameter array. Otherwise, the flash probe will fails.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Probably the non-use of the device parameter by the print routines did
not generate compilation errors.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Board gets reset when performing burst read/write operations. On the
other hand, no such behaviour is observed on small size operations.
In Linux, readl_poll_timeout API already adds delay of 1us which is
further skipped in U-boot. Hence, use new "readl_poll_sleep_timeout" API
which adds delay alongwith timeout functionality.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Clients that are requesting some of uclass API's
without a device (with ofnode) usually have _nodev
naming convention.
- clk_get_by_index_nodev
- clk_get_by_name_nodev
- reset_get_by_index_nodev
- gpio_request_by_name_nodev
So, update the same naming convention PHY framework.
This doesn't change the existing functionality.
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
lpc32xx_ssp driver is deprecated, no active updates
and no board user, hence dropped the same.
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Albert ARIBAUD <albert.aribaud@3adev.fr>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Make sure that all devices that are powered up by SPL are powered down
before entering into the u-boot. Otherwise the subsystem/device will
never be powered down by SCFW, due to SPL and u-boot are in different
partitions.
Benefiting from power domain driver, this patch implements the function
"imx8_power_off_pd_devices" to power off all active devices.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add more BCH setting mode and remove the unnecessary platform constrain
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
We are currently using SC_R_LAST as a marker for imx8 power domain tree
nodes without a resource attached. This value is compiled into dtb as
part of the linux build and used by uboot.
The SC_R_LAST constant changes frequently as SCFW resources are added
(by design) and every time we need to update linux and uboot headers
together or boot can fail.
Fix this by replacing SC_R_LAST usage with a new constant SC_R_NONE
defined to be 0xFFF0.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When fspi is assigned to M4, we have to let the fspi probe failed when
its power domain is failed to power up. Because not all devices have power
domain (for example, external devices on the board). Current checking
resource owner in power domain probe is not good, change to check it in
power on.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
For all the devices used and set ACTIVE in U-Boot, U-Boot needs
to power off all of them without the check of resource owner.
When we create software partition before booting Linux, the resource
own checkw will return false, and cause the power domain not powered
off. If without the check of resource owner, the power domain in
the other software partition could be powered off with parent
partition could access child partition resources.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
If without this flag, calling dev_power_domain_ctrl will iteratively remove
the power domain device will causes iteratively power off parent PD. This is
not expected by imx8-power-domain-legacy driver. Power off parent PD is
controlled by the driver internally.
So set DM_FLAG_DEFAULT_PD_CTRL_OFF to avoid such issue
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add power_domain_lookup_name interface to power domain uclass to find
a power domain device by its DTB node name, not using its associated
client device.
Through this interface, we can operate the power domain devices directly.
This is needed for non-DM drivers.
Modified from Ye's NXP downstream patch
only for legacy imx8 power domain driver, since we have not migrated
to use new power domain driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To enable the Randomizer module, set GPMI_ECCCTRL[RANDOMIZER_ENABLE] to
1, then set GPMI_ECCCOUNT[RANDOMIZER_PAGE] to select randomizer page
number needed to be randomized.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When enabled randomizer during ECC reading, the controller reported it's
erased page. Checking zero count will cause data get modified to all
0xFF. Stop checking during randomizer to workaround this issue.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since iMX8 has enabled clock uclass, we can parse the clocks from DTB
and enable them in GPMI driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
enable the GPMI NAND driver for i.MX8, i.MX8 use similar controller as
i.MX8M
- register definition for i.mx8
- DMA structure must be 32bit address
Signed-off-by: Peng Fan <peng.fan@nxp.com>
imx8mm needs to BCH encode and set NAND page number needed to be
randomized
modify conditional compilation
Use CONFIG_IMX8M, so it apply to imx8mq/mm/mn
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The iMX6SX uses compatible string "fsl,imx6sx-gpmi-nand" for gpmi
node in DTS, so update the driver for the string
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update the mini driver to add support for getting ecc info from ONFI and
support read image data from page unaligned NAND address.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update the gpmi/apbh_dma/bch drivers and relevant registers for i.MX8M.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This patch is a porting of
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/
commit/?h=imx_4.1.15_1.0.0_ga&id=e4dacc44d22e9474ec456cb330df525cd805ea38
"
i.MX6QP and i.MX7D BCH module integrated a new feature to detect the
bitflip number for erased NAND page. So for these two platform, set the
erase threshold to gf/2 and if bitflip detected, GPMI driver will
correct the data to all 0xFF.
Also updated the imx6qp dts file to ditinguish the GPMI module for i.MX6Q
with the one for i.MX6QP.
"
In this patch, i.MX6UL is added and threshold changed to use ecc_strength.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This patch is porting from linux:
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/commit/
?h=imx_4.1.15_1.0.0_ga&id=3d42fcece496224fde59f9343763fb2dfc5b0768
"
We may meet the bitflips in reading an erased page(contains all 0xFF),
this may causes the UBIFS corrupt, please see the log from Elie:
-----------------------------------------------------------------
[ 3.831323] UBI warning: ubi_io_read: error -74 (ECC error) while reading 16384 bytes from PEB 443:245760, read only 16384 bytes, retry
[ 3.845026] UBI warning: ubi_io_read: error -74 (ECC error) while reading 16384 bytes from PEB 443:245760, read only 16384 bytes, retry
[ 3.858710] UBI warning: ubi_io_read: error -74 (ECC error) while reading 16384 bytes from PEB 443:245760, read only 16384 bytes, retry
[ 3.872408] UBI error: ubi_io_read: error -74 (ECC error) while reading 16384 bytes from PEB 443:245760, read 16384 bytes
...
[ 4.011529] UBIFS error (pid 36): ubifs_recover_leb: corrupt empty space LEB 27:237568, corruption starts at 9815
[ 4.021897] UBIFS error (pid 36): ubifs_scanned_corruption: corruption at LEB 27:247383
[ 4.030000] UBIFS error (pid 36): ubifs_scanned_corruption: first 6569 bytes from LEB 27:247383
-----------------------------------------------------------------
This patch does a check for the uncorrectable failure in the following steps:
[0] set the threshold.
The threshold is set based on the truth:
"A single 0 bit will lead to gf_len(13 or 14) bits 0 after the BCH
do the ECC."
For the sake of safe, we will set the threshold with half the gf_len, and
do not make it bigger the ECC strength.
[1] count the bitflips of the current ECC chunk, assume it is N.
[2] if the (N <= threshold) is true, we continue to read out the page with
ECC disabled. and we count the bitflips again, assume it is N2.
(We read out the whole page, not just a chunk, this makes the check
more strictly, and make the code more simple.)
[3] if the (N2 <= threshold) is true again, we can regard this is a erased
page. This is because a real erased page is full of 0xFF(maybe also has
several bitflips), while a page contains the 0xFF data will definitely
has many bitflips in the ECC parity areas.
[4] if the [3] fails, we can regard this is a page filled with the '0xFF'
data.
"
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Provide an option in DT to use legacy bch geometry, which compatible
with the 3.10 kernel bch setting. To enable the feature, adding
"fsl,legacy-bch-geometry" under gpmi-nand node.
NOTICE: The feature must be enabled/disabled in both u-boot and kernel.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The code change updated the NAND driver BCH ECC layout algorithm to
support large oob size NAND chips(oob > 1024 bytes) and proposed a new
way to set ECC layout.
Current implementation requires each chunk size larger than oob size so
the bad block marker (BBM) can be guaranteed located in data chunk. The
ECC layout always using the unbalanced layout(Ecc for both meta and
Data0 chunk), but for the NAND chips with oob larger than 1k, the driver
cannot support because BCH doesn’t support GF 15 for 2K chunk.
The change keeps the data chunk no larger than 1k and adjust the ECC
strength or ECC layout to locate the BBM in data chunk. General idea for
large oob NAND chips is
1.Try all ECC strength from the minimum value required by NAND spec to
the maximum one that works, any ECC makes the BBM locate in data chunk
can be chosen.
2.If none of them works, using separate ECC for meta, which will add one
extra ecc with the same ECC strength as other data chunks. This extra
ECC can guarantee BBM located in data chunk, of course, we need to check
if oob can afford it.
Previous code has two methods for ECC layout setting, the
legacy_calc_ecc_layout and calc_ecc_layout_by_info, the difference
between these two methods is, legacy_calc_ecc_layout set the chunk size
larger chan oob size and then set the maximum ECC strength that oob can
afford. While the calc_ecc_layout_by_info set chunk size and ECC
strength according to NAND spec. It has been proved that the first
method cannot provide safe ECC strength for some modern NAND chips, so
in current code,
1. Driver read NAND parameters first and then chose the proper ECC
layout setting method.
2. If the oob is large or NAND required data chunk larger than oob size,
chose calc_ecc_for_large_oob, otherwise use calc_ecc_layout_by_info
3. legacy_calc_ecc_layout only used for some NAND chips does not contains
necessary information. So this is only a backup plan, it is NOT
recommended to use these NAND chips.
Signed-off-by: Han Xu <b45815@freescale.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When power on some sources in Video system, current timeout 10ms is
too short and returns before SCU response. So increase the timeout
to 1s.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Support i.MX8MP thermal which has two probes and supports
temperature range from -40 to 125. Still uses default 1p HW
calibration at 25C and loads calibration parameters from fuse.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On iMX8MM, the V flag in TRISTR register only reflect the state of SNSR
value, not the calibrated TEMP value. So checking this flag is not
reliable. Per IC suggestion, change to read the TEMP/AVG_TEMP directly
and check whether it in valid range 10-125C.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When the temperature is out of sensor's range, the Valid bit won't be
set in TRITSR register. So the polling loop won't go out.
Change the codes to retry 10 times with 100ms interval for the Valid bit.
If the timeout, we give a warning for the invalid data.
Modifed from Ye's NXP patch
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MM TMU needs to load some registers from fuse, this is arch
dependent operation and may vary on different platforms. So add
a interface for arch level initialization.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The analog sensors on iMX8MM are new, used for 14LPP process. So the
Temperature Sensor Monitoring Unit (TMU) has some change accordingly.
We use version 2 in TMU driver to represent the new TMU, so the one
driver can service for both i.MX8MQ/M.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The driver is ported form Linux Kernel and support driver model.
Users need to provide the tmu node and sensors nodes in DTB.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Implement the read_rom_hwaddr callback to load MAC address from fuse
for imx8m platforms.
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
imx_get_mac_from_fuse is used to load MAC address from fuse. On imx8mp,
we have two different ENET controllers and both need to call this
function. So decouple its declare from fec driver.
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Implement the callbacks to get phy mode interface and txclk
rate configuration.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add dwc eqos for imx support.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add RX delay enable support for RTL8211F PHY.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
For dual ethernet controllers, the HW design may connect ETH phys to
one MDIO ports. So two different ethernet drivers have to share MDIO bus.
Since two ethernet drivers are independent, we can't ensure their probe
order.
To resolve this problem, introduce an eth phy generic driver and uclass.
After eth-uclass binds, we search the mdio node and binds the phy node
with the eth-phy-generic driver.
When one eth driver get its phy device, the parent of phy device will
probe prior than phy device. So this ensure the eth driver ownes the
MDIO bus will be probed before using its MDIO.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
If a pad is not owned by current partition we should not set its
pinmux.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add fuse check for fec. If the fuse indicates the module
will not work in the SoC, let's fail the initialization.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add fuse check for USB. If the fuse indicates the module
will not work in the SoC, let's fail the initialization.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add fuse check for I2C. If the fuse indicates the module
will not work in the SoC, let's fail the initialization.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In RGMII mode the 10Mbps link speed is supported only when CPSW2G MAC SL is
configured for External Control ("in band") mode
CPSW_PN_MAC_CONTROL_REG.CTL_EN(18) = 1
Hence update am65_cpsw_update_link() to follow documentation.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
The reset_sata should reset the sata device info and free the
probe_ent memory. Otherwise, it will cause memory leak if we
init the sata again.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix coverity issue CID 43665: Free of address-of expression (BAD_FREE)
incorrect_free: free frees incorrect pointer pp.
pp points the port array field of struct ahci_uc_priv, should not free it.
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix coverity issue CID 3261683: Wrong operator used
(CONSTANT_EXPRESSION_RESULT) operator_confusion:
({...; __v;}) | 67108864 is always 1/true regardless of the values
of its operand. This occurs as the logical operand of !
When DIAG_X is set, the PHY COMINIT signal is detected, so
should use '&' to check whether it is set.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix coverity issue CID 3606684: Resource leak (RESOURCE_LEAK)
leaked_storage: Variable uc_priv going out of scope leaks the storage it points to
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move CONFIG_SYS_MTDPARTS_RUNTIME into Kconfig done by moveconfig.py.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The two functions are now exactly the same, remove one of them.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
We can configure the clock output in the device tree. Disable the
hardcoded one in here. This is highly board-specific and should have
never been enabled in the PHY driver.
If bisecting shows that this commit breaks your board it probably
depends on the clock output of your Atheros AR8035 PHY. Please have a
look at doc/device-tree-bindings/net/phy/atheros.txt. You need to set
"clk-out-frequency = <125000000>" because that value was the hardcoded
value until this commit.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add support for configuring the CLK_25M pin as well as the RGMII I/O
voltage by the device tree.
By default the AT803x PHYs outputs the 25MHz clock of the XTAL input.
But this output can also be changed by software to other frequencies.
This commit introduces a generic way to configure this output.
Also the PHY supports different RGMII I/O voltages: 1.5V, 1.8V and 2.5V.
An internal LDO is able to provide 1.5V (default) and 1.8V. The 2.5V
option needs an external supply voltage. This commit adds support to
switch the internal LDO to 1.8V.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Provide functions to read and write the Atheros debug registers.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Debug register 5 contains TX_CLK DELAY at bit 8 and reserved values at
the other bit positions, just like the other PHYs in the family do.
Therefore, it is not necessary to hardcode the reserved values, but
instead simply follow the read-modify-write procedure from the common
function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
To eliminate any doubts about the out-of-reset value of the PHY, that
the driver previously relied on.
If bisecting shows that this commit breaks your board you probably have
a wrong PHY interface mode. You probably want the
PHY_INTERFACE_MODE_RGMII_RXID or PHY_INTERFACE_MODE_RGMII_ID mode.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Also take the opportunity to use the phy_read_mmd and phy_write_mmd
convenience functions.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Delete the extraneous write to debug reg 5 that enables Tx delay
When the driver was originally introduced in commit "6027384a phylib:
Add Atheros AR8035 GETH PHY support", the Tx delay was being
unconditionally enabled.
Then during "2ec4d10b phy: atheros: add support for RGMII_ID, RGMII_TXID
and RGMII_RXID", the author did not notice that code for enabling Tx
delay code was already. Therefore, the if condition for Tx delay has
always been useless for this PHY since this commit introduced it.
Prior to this patch, every AR8035 PHY in U-boot had Tx delay enabled.
After this patch, only those who define the interface as RGMII_TXID or
RGMII_ID will. This is to be expected, but will nonetheless break the
setups of those who didn't know they rely on Tx delay implicitly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Even though the PL011 UART driver claims to be DM compliant, it does not
really a good job with parsing DT nodes. U-Boot seems to adhere to a
non-standard binding, either requiring to have a "skip-init" property in
the node, or to have an extra "clock" property holding the base
*frequency* value for the baud rate generator.
DTs in the U-Boot tree seem to have been hacked to match this
requirement.
The official binding does not mention any of these properties, instead
recommends a standard "clocks" property to point to the baud base clock.
Some boards use simple "fixed-clock" providers, which U-Boot readily
supports, so let's add some simple DM clock code to the PL011 driver to
learn the rate of the first clock, as described by the official binding.
These clock nodes seem to be not ready very early in the boot process,
so provide a fallback value, by re-using the already existing
CONFIG_PL011_CLOCK variable.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[trini: Add <clock_legacy.h> for get_bus_freq() for layerscape
platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In commit f62782fb29 ("cache: l2x0: Fix write to incorrect shared-override
bit") we removed writel to regs->pl310_aux_ctrl by accident. This
commit restores it back.
Fixes: f62782fb29 ("cache: l2x0: Fix write to incorrect shared-override bit")
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
- Add DM model for P1010RDB
- Add I2C DM Model support for P1010RDB, T1042RDB, T2080, T4240RDB,
MPC8548CDS, T1024RDB, P4080, P3041DS, P2041RDB, P2020RDB, P1020RDB,
P5040DS
- Fix reference to READM.qe_firmware
Commit 69529c9120 ("net: pcnet: Switch to PCI memory access")
switched from PCI IO access to PCI memory access without updating
the I/O primitives. Contrary to SH, the primitives for memory
access and IO access are implemented differently. Thus doing
memory access with IO port primitives breaks the driver on
MIPS Malta board.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
- dts clean up to use -u-boot for px30, rk3399 boards
- dts sycn from upstream kernel for rk3328, rk3399
- add rockchip rng driver
- new board support: rk3328-roc-cc, rk3399-roc-pc,Nanopi M4 2GB
This is part 1 of big network cleanup / DM conversion.
The dc2114x/rtl8139/pcnet/tulip PCI adapter drivers received checkpatch
cleanups in preparation for DM conversion. The smc911x is converted to
DM completely. The dwc_eth_qos cache fixes are applied.
In two files README.qe_firmware is referenced which never made it into the
U-Boot tree. The README is available in the Linux kernel tree.
Update the references.
Cc: Timur Tabi <timur@kernel.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add REVC informaiton.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
iMX8QM registers two thermal devices for CPUs, get the temperature
from "cpu-thermal1" device for A72
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When current cpu is A53, using is_cortex_a53 could not detect A72
information, so check cpu device compatible property to get
the correct information.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Return 4 is not correct on i.MX8DX/DXL/8QM and etc. we need to count
available cpu node with device_type "cpu".
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When running on SoC with multiple clusters, the boot CPU may
not be fixed, saying booting from cluster A or cluster B.
Add a API that can return the udevice for current boot CPU.
Cpu driver needs to implement is_current_cpu interface for this
feature, otherwise the API only returns the first udevice in
cpu uclass.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
If SDP_WRITE and SDP_JUMP addr is zero, use CONFIG_SDP_LOADADDR
as default address
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This patch is used to support the on-chip xHCI controller on
MediaTek SoCs, currently control/bulk/interrupt transfers are
supported.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Usually the digital and analog phys use the same reference clock,
but some platforms have two separate reference clocks for each of
them, so add another optional clock to support them.
In order to keep the clock names consistent with PHY IP's, change
the da_ref for analog phy and ref clock for digital phy.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
The new version removes all shared banks between multi-phys
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Support USB2 and USB3 PHY with shared banks when support multi-phys
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Use the phy bulk API to get a group of phys
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Get a group of phys by the phy bulk API
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds a "bulk" API to the phy API in order to
get/init/exit/power on/off a group of phys associated
with a device.
The bulk API will avoid adding a copy of the same code to
manage a group of phys in drivers.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This patch add function used to get the child count of
a ofnode or a device
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
LCDIF clock gate was wrong so set it according to RM.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The timers compatible string in upstream is called
mt6577-timer. Add this compatible to the driver.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
As noted in rtc_def.h, the tm_mon field in struct rtc_time is 1-12,
unlike in struct tm where it is 0-11. Currently, running "date" prints
the wrong
Date: 2020-04-01 (Friday) Time: 13:05:30
and setting the RTC via the date command is also broken.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Add support for U-Boot DM and DT probing. Furthermore, build the
SMC911x standalone EEPROM example only for the non-DM case, as it
is not converted yet.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch enables the possibility to set FEC_ENET_ENABLE_TXC_DELAY or
FEC_ENET_ENABLE_RXC_DELAY so one can via a define enable the RXC or TXC
delay in the MAC.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Add a module to configure the tamper and secure violation of
the SNVS using the SCU API.
The module also adds some commands:
- snvs_cfg: Configure the SNVS HP and LP registers
- snvs_dgo_cfg: Configure the SNVS DGO bloc if present (8QXP)
- tamper_pin_cfg: Change the configuration of the tamper pins
- snvs_clear_status: Allow to write to LPSR and LPTDSR to clear
status bits
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Franck LENORMAND <franck.lenormand@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sync the latest SCFW API with below commit
6dcd0242ae7a53ac ("SCF-105: Revert accidental change") to add
interfaces for PM resource reset and read/write SNVS security
violation and tamper DGO registers.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Split network handling functions into non-DM specific parts and
common code in preparation for conversion to DM.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Invert the status handling logic in smc911x_recv(), to make the
function easier to read, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Introduce a private data structure for this driver with embedded
struct eth_device and pass it around. This prepares the driver to
work with both DM and non-DM systems.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Convert the IO accessors to standard ones instead of using volatile
void pointers, as those do not cover all the bus access details.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
These accessors are not overridden by any board, and even if they were,
this is something which should be handled via DM now, so remove the
weak alias option. Moreover, drop the inline keyword, as the compiler
can decide better.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Inline all the functions from the header file, as they are not used
outside of the driver or the standalone EEPROM example.
Note that this does introduce considerable amount of duplication in
the standalone EEPROM example, however that one has to be rewritten
anyway, roughly such that the SMC911x driver would expose DM EEPROM
interface and the standalone example would use that.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Pull the MII interface registration into separate function to avoid the
ifdeffery in smc911x_initialize(). Moreover, adjust the fail path such
that we use goto labels.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Fix memleak in the init fail path, where if allocation or registration
of MDIO bus fails, then ethernet interface is not unregistered and the
private data are not freed, yet the probe function reports a failure.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Invert the logic in the aforementioned functions to reduce indent,
no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Rename the function to keep the naming scheme consistent,
no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Replace combination of malloc()+memset() with calloc() as the behavior
is exactly the same and the amount of code is reduced.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
These functions are never used and are likely a pre-DM remnant
from times long past, just remove them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
The rtl8139 driver is derived from Etherboot driver, which is in
turn derived from Linux 8139too driver added in Linux 2.2.18pre14.
An undocumented change in Linux 2.4.10.2 added a new field to the
driver, MODULE_LICENSE("GPL"); . According to current Linux kernel
licensing rules, Documentation/process/license-rules.rst, quote:
"GPL" Module is licensed under GPL version 2. This
does not express any distinction between
GPL-2.0-only or GPL-2.0-or-later. The exact
license information can only be determined
via the license information in the
corresponding source files.
And since the code does not contain any "future" clause, the tag
is therefore GPL-2.0 only.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Just move functions around in preparation for easy DM conversion,
rename rtl_bcast_addr() to rtl8139_bcast_addr(), no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Finish the checkpatch cleanup of the driver, fix the remaining issues
in probe and init function and in global variables, rename the probe
function to rtl8139_init(), no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
This hardware reset and reset-wait implementation was twice in the
driver, factor it out into a separate function. This really should
use wait_for_bit() eventually and return -ETIMEDOUT, but thus far,
handling of any of this is missing from the driver. This must be
added later. Thus far, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_stop(), clean up checkpatch errors in
the stop polling function. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_recv(), clean up various checkpatch errors,
line-over-80 conditions, and malformed comments. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_send(), clean up the TX polling, the TX
OK condition at the end, overuse of typecasts, and various line-over-80
problems. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_reset(), clean up the reset polling
and various line-over-80 problems. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_set_rx_mode(), use unsigned variables
where applicable and inline mc_filter[] values. No functional chanage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
This string of macros is exactly the same thing as rtl8139_rx_config,
so just use rtl8139_rx_config. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_read_eeprom() to keep the naming
consistent, keep the variables sorted in reverse xmas tree. No
functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The macro assumes ee_addr variable to be present when it's being
used. Rework the macro into a function instead and pass it an
argument specifying the register base address, to make it future
proof for DM conversion.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the horrible register definitions in the RTL8139 driver.
This does create a couple of checkpatch errors, but the driver is
full of them anyway, and those will be cleaned up later.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The DMA may attempt to write a DMA descriptor in the ring while it is
being updated. By writing the DMA descriptor buffer address to 0, it
is assured the DMA will not use such a buffer and the buffer can be
updated without any interference.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
This patch prevents an issue where the RX packet might have been
accessed by the CPU, which now has cached data from the packet in
the caches and possibly various write buffers, and these data may
be evicted from the caches into the DRAM while the buffer is also
written by the DMA.
By invalidating the buffer after the CPU accessed it and before the
DMA populates the buffer, it is assured that the buffer will not be
corrupted.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
The current code polls the RX desciptor ring for new packets by reading
the RX descriptor status. This works by accident, as the RX descriptors
are often in non-cacheable memory. However, the driver does support use
of RX descriptors in cacheable memory.
This patch adds a missing RX descriptor invalidation, which assures the
CPU will read a fresh copy of the RX descriptor instead of a cached one.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Currently the code only flushes the first RX descriptor, not every entry
in the RX descriptor ring. Fix this, to make sure the DMA engine can pick
the RX descriptors correctly.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
This code programs the next descriptor in the TX descriptor ring into
the hardware as the last valid TX descriptor. The problem is that if
the currenty descriptor is the last one in the array, the code will
not wrap around correctly and use TX descriptor 0 again, but instead
will use TX descriptor at address right past the TX descriptor ring,
which is the first descriptor in the RX ring.
Fix this by adding the necessary wrap-around.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
The RX descriptor field 3 should contain only OWN and BUF1V bits before
being used for receiving data by the DMA engine. However, right now, if
the descriptor was already used for receiving data and is being cleared,
the field 3 is only modified and the aforementioned two bits are ORRed
into the field. This could lead to a residual dirty bits being left in
the field 3 from previous transfer, and it generally does. Fully set the
field 3 instead to clear those residual dirty bits.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Replace the adhoc debugging ifdeffery with debug_cond() and an
internal SROM_DEBUG macro to select the debug level.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Move the functions in the driver around to better fit future DM
conversion, drop function forward declarations. No functional
change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename these functions to dc2114x_{inl,outl}(), use u32 values in
them instead of plain signed integers as all those values are in
fact register values and the driver code does bitwise operations
on them. No functional change intended.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Replace these macros with static functions to permit the compiler to
do type checking on the functions. The INL()/OUTL() functions have to
be moved in this patch as well, as those DE4X5 macros are using them.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the remaining driver code, macro space alignment, function
declaration indent, replace __attribute__((aligned(32))) with plain
__aligned(32). No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the SROM accessors to bring them up to standards with
U-Boot coding style. Sort variable into reverse xmas tree. No
functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the send_setup_frame() to bring it up to standards with
U-Boot coding style, invert the loops where applicable to cut
down the level of indent. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the driver halt code to bring it up to standards with
U-Boot coding style. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the driver recv code to bring it up to standards with
U-Boot coding style. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the driver send code to bring it up to standards with
U-Boot coding style, invert the loops where applicable to cut
down the level of indent. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the driver init code to bring it up to standards with
U-Boot coding style, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Replace the PCI IO access with PCI memory access, the card
supports both, but the former does not work with QEMU SH4.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Replace mips-specific UNCACHED_SDRAM() macro with standard
map_physmem(), which permits the driver to work on other
systems than mips.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
These macros are not used by any board, remove them to simplify
the driver. The EEPROM accessors are still retained however, as
those might still be useful.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
