Several Octeon drivers operate by setting the sequence number of their
device. This should not be needed with the new sequence number setup. Also
it is not permitted. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present various drivers etc. access the device's 'seq' member directly.
This makes it harder to change the meaning of that member. Change access
to go through a function instead.
The drivers/i2c/lpc32xx_i2c.c file is left unchanged for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is not necessary anymore, since device_bind_ofnode() does
the same thing and works with both flattree and livetree.
Rename it to indicate that it is special.
Signed-off-by: Simon Glass <sjg@chromium.org>
LX2162 is LX2160 based SoC, it has same die as of LX2160
with different packaging.
LX2162A support 64-bit 2.9GT/s DDR4 memory, i2c, micro-click module,
microSD card, eMMC support, serial console, qspi nor flash, qsgmii,
sgmii, 25g, 40g, 50g network interface, one usb 3.0 and serdes
interface to support three PCIe gen3 interface.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
[Fixed whitespace errors]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can
be controlled via defconfig files.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In case there is an EEPROM attached to the KS8851 MAC and the EEPROM
contains a valid MAC address, the MAC address is loaded into the NIC
registers on power on. Read the MAC address out of the NIC registers
and provide it to U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
As per hardware documentation, ECx_PMUX has precedence
over SerDes protocol.
For LX2160/LX2162 if DPMACs 17 and 18 are enabled as SGMII
through SerDes protocol but ECx_PMUX configured them as RGMII,
then the ports will be configured as RGMII and not SGMII.
Signed-off-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This adds the driver for the IPQ40xx built-in MDIO.
This will be needed to support future PHY driver.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
When sending a command via the MDIO bus, the Designware MAC expects some
bits in the CMD register to describe the clock divider value between
the main clock and the MDIO clock.
So far we were omitting these bits, resulting in setting "00", which
means "/ 16", so ending up with an MDIO frequency of either 18.75 or
12.5 MHz.
All the internal PHYs in the H3/H5/H6 SoCs as well as the Gbit Realtek
PHYs seem to be fine with that - although it looks like to be severly
overclocked (the MDIO spec limits the frequency to 2.5 MHz).
However the external 100Mbit PHY on the Pine64 (non-plus) board is
not happy with that, Ethernet was actually never working there, as the
PHY didn't probe.
As we set the EMAC clock (via AHB2) to 300 MHz in ATF (on the 64-bit
SoCs), and use 200 MHz on the H3, we need the highest divider of 128
to let the MDIO clock end up below the required 2.5 MHz.
This enables Ethernet on the Pine64(non-plus).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The current implementation of sun8i_get_ephy_nodes() makes quite some
assumptions, in general relying on DT path names is a bad idea.
I think the idea of the code was to determine if we are using the
internal PHY, for which there are simpler and more robust methods:
Rewrite (and rename) the existing function to simply lookup the DT node
that "phy-handle" points to, using the device's DT node.
Then check whether the parent of that PHY node is using an "H3 internal
MDIO" compatible string. If we ever get another internal MDIO bus
implementation, we will probably need code adjustments anyway, so this
is good enough for now.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[jagan: rebase on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The error handling in recv() is somewhat broken, for instance
good_packet isn't really used, and it's hardly readable. Also we try
to check for short or too big packets, but those are actually filtered
out by the hardware.
Simplify the whole routine and improve the error handling:
- Bail out early if the current RX descriptor is not ready.
- Enable propagation of runt, huge and broken packets.
- Check for runt and huge packets, and return 0 to indicate this.
This will force the framework to call free_pkt for cleanup.
- Avoid aligning the packet buffer for invalidation again.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The EMAC soft reset routine was subtly broken, using an open coded
timeout routine without any actual delay.
Remove the unneeded initial reset bit read, and call wait_for_bit_le32()
to handle the timeout correctly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When iterating over all RX/TX buffers, we were using a rather long "idx"
control variable, which lead to a nasty overlong line.
Replace "idx" with "i" to avoid this.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
To meet the current alignment requirements for our cache maintenance
functions, we were explicitly aligning the *arguments* to those calls.
This is not only ugly to read, but also wrong, as we need to make sure
we are not accidentally stepping on other data.
Provide wrapper functions for the common case of cleaning or
invalidating a descriptor, to make the cache maintenance calls more
readable. This fixes a good deal of the problematic calls.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
There is no reason to invalidate a TX descriptor before we are setting
it up, as we will only write to a field.
Remove the not needed invalidate_dcache_range() call.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When we initialise the TX descriptors, there is no need yet to clean
them all to memory, as they don't contain any data yet. Later we will
touch and clean each descriptor anyway.
However we tell the MAC about the beginning of the chain, so we have to
clean at least the first descriptor, to make it clear that this is empty
and there are no packets to transfer yet.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Before we initialise the RX descriptors, there is no need to *clean*
them from the cache, as we touch them for the first time.
However we should cover the case that those buffers contain dirty cache
lines, which could be evicted and written back to DRAM any time later,
in the worst case *after* the MAC has transferred a packet into them.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The EMAC driver contains a lot of magic bits, although the manuals
and the Linux driver have all names for them.
Define those names and use them when programming the registers.
Also this replaces a lot of readl/mask/writel operations with the much
easier-to-read setbits_le32() macro.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Apparently due to copying from some older or converted driver, the
sun8i_emac driver contains pointless wrapper functions to bridge
between a legacy driver and the driver model.
Since sun8i_emac is (and always was) driver model only, there is no
reason to have those confusing wrappers. Just remove them, and use
the driver model prototypes directly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When preparing the register value for the MDIO command register, we
start with a zeroed register, so there is no need to mask off certain
bits before setting them.
Simplify the sequence, and rename the variable to a more matching
mii_cmd on the way.
Also the open-coded time-out routine can be replaced with a much safer
and easier-to-read call to wait_for_bit_le32().
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When initialising the TX DMA descriptors, we mostly chain them up,
but of course don't know about any data or its length yet.
That means they are still invalid, and the OWN bit should NOT be set
yet.
In fact when we later tell the MAC about the beginning of the chain,
and enable TX DMA in the start() routine, the MAC will start fetching
TX descriptors prematurely, as it can be seen by dumping the TX_DMA_STA
and TX_DMA_CUR_DESC registers.
Clear the owner bit, to not give the MAC the wrong illusion that it
owns the descriptors already.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When phy_startup() returns with an error, because there is no link or
the user interrupted the process, we shall stop the _start() routine
and return with an error, instead of proceeding anyway.
This fixes pointless operations when there is no Ethernet cable
connected, for instance.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
- Octeon TX: Add NAND driver (Suneel)
- Octeon TX: Add NIC driver driver (Suneel)
- Octeon TX2: Add NIC driver driver (Suneel)
- Armada 8040: Add iEi Puzzle-M80 board support (Luka)
- Armada A37xx SPI: Add support for CS-GPIO (George)
- Espressobin: Use Linux model/compatible strings (Andre)
- Espressobin: Add armada-3720-espressobin-emmc.dts from Linux (Andre)
- Armada A37xx: Small cleanup of config header (Pali)
Set the defaults on probe for the packet buffer size registers
for the i210.
The TX/RX PBSIZE register of the i210 resets to its default value
only at power-on - see Intel Ethernet Controller I210 Datasheet rev 3.5
chapter 8.3 'Internal Packet Buffer Size Registers'.
If something (another driver, another OS, etc.) modifies this register
from its default value, the e1000 driver doesn't function correctly. It
detects a hang of the transmitter and continuously resets the adapter.
Here we set this value to its default when resetting the i210 to
resolve this issue.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Adds support for Network Interface controllers found on
OcteonTX2 SoC platforms.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Adds support for Network Interface controllers found on
OcteonTX SoC platforms.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The cell_count argument is required when cells_name is NULL.
This patch adds this parameter in live tree API
- of_count_phandle_with_args
- ofnode_count_phandle_with_args
- dev_count_phandle_with_args
This parameter solves issue when these API is used to count
the number of element of a cell without cell name. This parameter
allow to force the size cell.
For example:
count = dev_count_phandle_with_args(dev, "array", NULL, 3);
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Upon further discussion on the mailing list, we should not get in the
situation where the generic code path to set ethaddr/etc correctly does
not work. Revert this until someone can further debug the smc911x
driver regarding this issue.
This reverts commit 387cbf096e.
Signed-off-by: Tom Rini <trini@konsulko.com>
Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the
driver can support live DT.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The ethernet controller can read the MAC from EEPROM and display it,
but if ethaddr is not set, the ethernet is still unavailable.
This patch checks will automatically set the MAC address if it has
not already been set.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
ftgmac100 driver is using hard-coded PHY interface address of zero.
Each board can have different PHY interface address (phy_addr).
This commit modifies the driver to make use of board specific address
by leveraging CONFIG_PHY_ADDR.
Signed-off-by: Thirupathaiah Annapureddy <thiruan@linux.microsoft.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
The Linux kernel does set the clock delays to
- 0.2 ns (their default, and lowest, hardware value) if delays should
not be enabled
- 2.0 ns (which causes the data to be sampled at exactly half way between
clock transitions at 1000 Mbps) if delays should be enabled
depending on the interface mode
See https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/net/phy/mscc/mscc_main.c#n523
So instead of using arbitrary delay values like now, mimic this behaviour.
The behaviour is the same for all of vsc8530/8531/8540/8541 so move that
to a shared function while at it.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The vsc8530/8531/8540/8541 phys have a configurable clock output that
can emit 25, 50 and 125 MHz rates, which in turn may be needed for
stable network connections.
This follows a similar change introduced into the Linux kernel at
https://lore.kernel.org/netdev/20200609133140.1421109-2-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Without DM_ETH, cpsw_priv.dev is an eth_device. Just use its name instead.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Pass a udevice into a few functions so `dev` is defined.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
There's no dev to log with, so pass the device along with the priv data.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
netdev_xxx evaluates to printf in U-Boot, so there is no extra info
printed. mvpp2 one of only two drivers which use these functions in U-Boot.
Convert these functions to dev_xxx where possible (and to log_xxx where
not).
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Remove some prefixes, or get the device from the phy.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
netdev_xxx evaluates to printf in U-Boot, so there is no extra info
printed. mvneta is one of two drivers which use these functions in U-Boot.
Convert these functions to dev_xxx where possible (and to log_xxx where
not).
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
No need for indirection here.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
The micrel phy driver is already configuring this values from
device tree. So remove the redundant phy configuration call from
this driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
CONFIG_DM_SPI_FLASH is only supported now with passing of driver
conversion deadline from non-DM to DM model. Hence, it's safe to remove
non-DM code check from pfe_spi_flash_init.
Also use CONFIG_ENV_SPI_MODE and CONFIG_ENV_SPI_MAX_HZ instead of
reading reading values from DT.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Fix Coverity issue: RESOURCE_LEAK.
leaked_storage: Variable addr going out of scope leaks the storage it
points to.
Fixes: e0152dbed6 ("net: pfe_eth: Use spi_flash_read API to access
flash memory")
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
All the 10G ports that were working in XFI mode were described as
using XGMII (as PHY_INTERFACE_MODE_XFI was not added at the time).
Add the minimal changes required for the FMan code to support XFI.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
PFE DDR addresses are now stored on to a stack varaiable rather
dynamic allocation.
Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
correction in delay implementation before we exit out of tx timeout.
Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The next DPMAC was always verified if it is enabled. In case of
DPMAC@6, the DPMAC@7 is verified. As DPMAC@7 is disabled, DPMAC@6 will
be considered disabled and not detected by uboot.
Signed-off-by: Grigore Popescu <grigore.popescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX2x4MgAKCRDKSWXLKUoM
IZQtAJ9HpNwG5q3nHt9WedzLCTkr3YoLAACeJJ0Wlpp5p5xPzuPmnoo/Vi4MtNQ=
=yxRo
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.01
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
The info of fixed-link PHY is described in DT node instead of
getting from MII, so detect the fixed-link PHY DT node first,
if it doesn't exist then probe the MII.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
For the platforms on which the eTSEC driver uses DM_ETH, convert its
MDIO controller code to also use DM_MDIO.
Note that for handling the TBI PHY (the MAC PCS for SGMII), we still
don't register a udevice for it, since we can drive it locally and there
is no point in doing otherwise.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Reworked to fix gazerbeam config]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The MII management register block offset is different between
gianfar and etsec2 compatible devices, this patch is to fix
this issue by adding driver data for different compatible
string.
Fixes: 2932c5a802 ("net: tsec: fsl_mdio: add DM MDIO support")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Use virtual address to access the MII block registers instead
of physical address.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
It is utterly pointless to require an MDIO bus pointer for a fixed PHY
device. The fixed.c implementation does not require it, only
phy_device_create. Fix that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
flush_cache() arguments are not type casted to take care of 64 bit
systems. Use phys_addr_t to type cast for it to work properly for 32 bit
and 64 bit systems.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
There are compilation warnings showing up when we compile AXI ethernet
driver for 64bit architectures. Fix them, so that it works on both 32
and 64 bit architectures.
DMA descriptors are not taking care of 64bit addresses. To fix it,
change axidma_bd members as below:
next ==> next_desc
reserverd1 ==> next_desc_msb
phys ==> buf_addr
reserverd2 ==> buf_addr_msb
and update next_desc and buf_addr with lower 32 bits of the addresses,
update next_desc_msb and buf_addr_msb with upper 32 bits of the 64bit
addresses.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Find out MDIO bus and enable MDIO access to it if this is done via
different GEM controller. Only works across GEM instances.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
add DM/DTS support for the UEC ethernet on QUICC Engine
Block.
Signed-off-by: Heiko Schocher <hs@denx.de>
Patch-cc: Mario Six <mario.six@gdsys.cc>
Patch-cc: Qiang Zhao <qiang.zhao@nxp.com>
Patch-cc: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Patch-cc: Madalin Bucur <madalin.bucur@oss.nxp.com>
Series-changes: 3
- revert:
commit "3374264df97b" ("drivers: net: qe: deselect QE when DM_ETH is enabled")
as now qe works with DM and DM_ETH support.
- fix mailaddress from Holger
Series-changes: 2
- add comments from Qiang Zhao:
- add device node documentation
- I did not drop the dm_qe_uec_phy.c and use drivers/net/fsl_mdio.c
because using drivers/net/fsl_mdio.c leads in none existent
udevice mdio@3320
instead boards with DM ETH support should use now this
driver.
- remove RFC tag
Commit-notes:
- I let the old none DM based implementation in code
so boards should work with old implementation.
This Code should be removed if all boards are converted
to DM/DTS.
- add the DM based qe uec driver under drivers/net/qe
- Therefore copied the files uccf.c uccf.h uec.h from
drivers/qe. So there are a lot of Codingstyle problems
currently. I fix them in next version if this RFC
patch is OK or it needs some changes.
- The dm based driver code is now under drivers/net/qe/dm_qe_uec.c
Used a lot of functions from drivers/qe/uec.c
- seperated the PHY specific code into seperate file
drivers/net/qe/dm_qe_uec_phy.c
END
The commit 57805f2270 ("net: bcmgenet: Don't set ID_MODE_DIS when
not using RGMII") needed to be extended for the case of using the
rgmii-rxid. The latest version of the Rasbperry Pi4 dtb files for the
5.4 now specify the rgmii-rxid.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Tested-by: Petr Tesarik <ptesarik@suse.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
This commit fixes a serious issue occurring when several network
commands are run on a raspberry pi 4 board: for instance a "dhcp"
command and then one or several "tftp" commands. In this case,
packet recv callbacks were called several times on the same packets,
and send function was failing most of the time.
note: if the boot procedure is made of a single network
command, the issue is not visible.
The issue is related to management of the packet ring buffers
(producer / consumer) and DMA.
Each time a packet is received, the ethernet device stores it
in the buffer and increments an index called RDMA_PROD_INDEX.
Each time the driver outputs a received packet, it increments
another index called RDMA_CONS_INDEX.
Between each pair of network commands, as part of the driver
'start' function, previous code tried to reset both RDMA_CONS_INDEX
and RDMA_PROD_INDEX to 0. But RDMA_PROD_INDEX cannot be written from
driver side, thus its value was actually not updated, and only
RDMA_CONS_INDEX was reset to 0. This was resulting in a major
synchronization issue between the driver and the device. Most
visible behavior was that the driver seemed to receive again the
packets from the previous commands (e.g. DHCP response packets
"received" again when performing the first TFTP command).
This fix consists in setting RDMA_CONS_INDEX to the same
value as RDMA_PROD_INDEX, when resetting the driver.
The same kind of fix was needed on the TX side, and a few variables
had to be reset accordingly (c_index, tx_index, rx_index).
The rx_index and tx_index have only 256 entries so the bottom 8 bits
must be masked off.
Originated-by: Etienne Dublé <etienne.duble@imag.fr>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Tested-by: Petr Tesarik <ptesarik@suse.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Zynq/ZynqMP/Versal IPs should be possible to called also from Microblaze in
PL and vice versa. That's why change dependencies and do not limit enabling
just for some platforms.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add configuration flag to select the supported dwc driver configuration:
- CONFIG_DWC_ETH_QOS_TEGRA186
- CONFIG_DWC_ETH_QOS_IMX
- CONFIG_DWC_ETH_QOS_STM32
See Linux driver ethernet/stmicro/stmmac and associated glue layers
for other configuration examples.
This patch removes the not-selected compatibles and lets the linker remove
the unused functions to reduce the size of the driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The sgmii mode init flow is almost the same for all mediatek SoC, the
only difference is the register offset(SGMSYS_GEN2_SPEED) is 0x2028
in the old chip(mt7622) but changed to 0x128 for the newer chip(mt7629
and the following chips).
Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
- Bug fixes and updates on ls2088a,ls1028a, ls1046a, ls1043a, ls1012a
- lx2-watchdog support
- layerscape: pci-endpoint support, spin table relocation fixes and
cleanups
- fsl-crypto: RNG support and bug fixes
The correct setting for the RGMII ports on LS1012ARDB is to
enable delay on both Rx and Tx so the interface mode used should
be PHY_INTERFACE_MODE_RGMII_ID
Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Signed-off-by: Anji J <anji.jagarlmudi@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Current PFE firmware access spi-nor memory directly. New spi-mem
framework does not support direct memory access. So, let's use
spi_flash_read API to access memory instead of directly using it.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
With all the changes in place, add support for DM into the
dc2114x driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Split the common code from the non-DM code, so it can be reused by
the DM code later. As always, the recv() function had to be split
into the actual receiving part and free_pkt part to fit with the
DM.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Split the RX data check from the rest of the RX function, so that
the check can be performed separately from the processing of the
packet and the release of the received packet once the processing
is finished.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
The RX/TX DMA descriptor rings are per-device-instance private data,
so move them into the private data.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
This is a trick in preparation for adding DM support. By passing in
the PCI BDF into the phys_to_bus() macros and calling that dev, we
can substitute dev with udevice when DM support lands and do minor
adjustment to the macros to support both DM and non-DM operation.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
This patch replaces the various uses of struct eth_device for accessing
device private data with struct dc2114x_priv, which is compatible both
with DM and non-DM operation.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Introduce dc2114x_priv, which is a super-structure around eth_device
and tracks per-device state and the device IO address.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
The current dc21x4x driver accesses its memory mapped registers directly
instead of using the standard I/O accessors. This can cause problems on
some systems as the accesses can get out of order. So convert the direct
volatile dereferences to use the normal in/out macros.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
This code is never used, remove it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Add Kconfig entries for the dc2114x driver and convert various boards.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
For the usage in this driver, the chips are identical,
so support all of them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Use this macro to fully fill the PCI device ID table. This is mandatory
for the DM PCI support, which checks all the fields.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Some code was not converted by coccinelle, somehow.
I manually fixed up the remaining, and comments, README docs.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
[trini: Add arch/arm/mach-davinci/include/mach/sdmmc_defs.h and
include/fdt_support.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:
It's a **mistake** to use typedef for structures and pointers.
Besides, using typedef for structures is annoying when you try to make
headers self-contained.
Let's say you have the following function declaration in a header:
void foo(bd_t *bd);
This is not self-contained since bd_t is not defined.
To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>
#include <asm/u-boot.h>
void foo(bd_t *bd);
Then, the include direcective pulls in more bloat needlessly.
If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:
struct bd_info;
void foo(struct bd_info *bd);
Right, typedef'ing bd_t is a mistake.
I used coccinelle to generate this commit.
The semantic patch that makes this change is as follows:
<smpl>
@@
typedef bd_t;
@@
-bd_t
+struct bd_info
</smpl>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Since the mdio code got upstreamed it is not possible
to activate network ports on CP110 Master and Slave.
The problem is in mvpp2_base_probe which is called for each
CP110 and it initializes the buffer area for descs and rx_buffers.
This should only happen once though and the bd space is actually
set to 0 after the first run of the function.
This leads to an error when the second CP110 tries the initialization
again and disables all network ports on this CP110.
This patch adds a static variable to check if the buffer area is
initialized only once globally.
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Reviewed-by: Stefan Roese <sr@denx.de>
When compiled as a DM_ETH driver, the scm911x driver was reading the MAC
address from the optional EEPROM storage, but failed to copy this to the
platdata struct. Since it was also missing a definition of the
read_rom_hwaddr() function, the generic Ethernet code was dismissing
this MAC address, falling back to a random address or denying to start
at all.
Add an implementation of .read_rom_hwaddr, and refactor the function
reading the ROM address to be called by all interested parties.
This fixes MAC address issues when using the driver in DM_ETH "mode".
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
This patchs adds glue logic to enable designware mac present on
Action Semi based S700 SoC, Configures SoC specific bits.
Undocumented bit that programs the PHY interface select register
comes from vendor source.
It has been tested on Cubieboard7-lite based on S700 SoC.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have
specific Rx/Tx interface timings requirement for proper PHY operations.
These timing values are not documented anywhere and picked from vendor
code.
This commits lets proper packets to be transmitted over the network.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This patch adds support for Realtek PHY RTL8201F 10/100Mbs
(with variants: RTL8201FN and RTL8201FL) PHYceiver. It is
present on Actions Semi Cubieboard7 board.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Update the compatible associated with the STM32 MPU glue
in the DWC ethernet driver.
The supported compatible is the specific "st,stm32mp1-dwmac"
as indicated in Linux binding
Documentation/devicetree/bindings/net/stm32-dwmac.txt
and not the "snps,dwmac-4.20a" only used to the select IP
version.
This glue is implemented in Linux kernel in:
drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c
For information in stm32mp151.dtsi, the 2 compatibles are
supported:
ethernet0: ethernet@5800a000 {
compatible = "st,stm32mp1-dwmac", "snps,dwmac-4.20a";
...
};
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
- Makefile: add rule to build an endian-swapped U-Boot image
used by MIPS Malta EL variants
- CI: add Qemu tests for MIPS Malta
-----BEGIN PGP SIGNATURE-----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=dnTK
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2020-06-29' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips into next
- net: pcnet: cleanup and add DM support
- Makefile: add rule to build an endian-swapped U-Boot image
used by MIPS Malta EL variants
- CI: add Qemu tests for MIPS Malta
Add Kconfig entries for the pcnet driver and convert MIPS malta
to use those.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
With all the changes in place, add support for DM into the
pcnet driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Pull the common parts of functions out so they can be reused by both
DM and non-DM code paths. The recv() function had to be reworked to
fit into this scheme and this means it now only receives one packet
at a time instead of spinning in an endless loop.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Instead of using the non-DM-only name and enetaddr in struct eth_device,
add pointers into the private data which can either point to that non-DM
name or a DM one later on.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Instead of using the non-DM-only iobase in struct eth_device, add
one into the private data to make DM and non-DM operation possible.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Get rid of the global point to private data, and rather pass it
thought dev->priv. Also remove the unnecessary check for lp being
non-NULL, since it is always NULL at this point.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Instead of using eth_device priv for this PCI devbusfn, free it
so it could be used for driver private data, and wrap devbusfn
into those driver private data.
Note that using the name dev for the variable is a trick left for
later, when DM support is in place, so dm_pci_virt_to_mem() can be
used with minimal ifdeffery.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Remove those as they are not needed anymore.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Move the function at the end of the driver, so we could drop
various forward declarations later. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The private data allocation does not have to be done every time the
NIC is initialized at run time, move the allocation to initialize
function, which means it will be done only once when the driver
starts.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
This combination of functions can be replaced with calloc(),
make it so.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The current code is horribly complex. Both the RX and TX buffer
descriptors are 16 bytes in size, the init block is 32 bytes in
size, so simplify the code such that the entire private data of
the driver are allocated cache aligned and the RX and TX buffer
descriptors are part of the private data.
This removes multiple malloc calls and cache flushes.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Use this macro to fully fill the PCI device ID table. This is mandatory
for the DM PCI support, which checks all the fields.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
All of one PCNET users has this option set, make this default
and drop this config option.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Use struct pcnet_priv all over the place instead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
This change allows more fine tuning of driver model based SPI support in
SPL and TPL. It is now possible to explicitly enable/disable the DM_SPI
support in SPL and TPL via Kconfig option.
Before this change it was necessary to use:
/* SPI Flash Configs */
#if defined(CONFIG_SPL_BUILD)
#undef CONFIG_DM_SPI
#undef CONFIG_DM_SPI_FLASH
#undef CONFIG_SPI_FLASH_MTD
#endif
in the ./include/configs/<board>.h, which is error prone and shall be
avoided when we strive to switch to Kconfig.
The goal of this patch:
Provide distinction for DM_SPI support in both U-Boot proper and SPL (TPL).
Valid use case is when U-Boot proper wants to use DM_SPI, but SPL must
still support non DM driver.
Another use case is the conversion of non DM/DTS SPI driver to support
DM/DTS. When such driver needs to work in both SPL and U-Boot proper, the
distinction is needed in Kconfig (also if SPL version of the driver
supports OF_PLATDATA).
In the end of the day one would have to support following use cases (in
single driver file - e.g. mxs_spi.c):
- U-Boot proper driver supporting DT/DTS
- U-Boot proper driver without DT/DTS support (deprecated)
- SPL driver without DT/DTS support
- SPL (and TPL) driver with DT/DTS (when the SoC has enough resources to
run full blown DT/DTS)
- SPL driver with DT/DTS and SPL_OF_PLATDATA (when one have constrained
environment with no fitImage and OF_LIBFDT support).
Some boards do require SPI support (with DM) in SPL (TPL) and some only
have DM_SPI{_FLASH} defined to allow compiling SPL.
This patch converts #ifdef CONFIG_DM_SPI* to #if CONFIG_IS_ENABLED(DM_SPI)
and provides corresponding defines in Kconfig.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[trini: Fixup a few platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXvScEQAKCRDKSWXLKUoM
IeHUAJ9Z1shAlbILuHZKEpqQySLHdUVgBQCff8Nf+wi1rByTrwflKt14MtIsdFY=
=2Yuu
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2020.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2020.10
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
The index used to iterate over the possible PHYs in axiemac_phy_init was an
unsigned int and decremented. Therefor it was always >= 0 and never exited
the loop.
Signed-off-by: Patrick van Gelder <patrick.vangelder@nl.bosch.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Disable PCS autonegotiation if fixed-link node is present in device tree.
This way systems with multiple GEM instances with a combination of
SGMII-fixed and SGMII-PHY will work.
Reported-by: Goran Marinkovic <goran.marinkovic@psi.ch>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
As we move towards driver model, it is required to let the FEC driver
know how to properly deal with an Ethernet PHY subnode in the device tree.
For example:
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_microsom_enet_ar8035>;
phy-handle = <&phy>;
phy-mode = "rgmii-id";
phy-reset-duration = <2>;
phy-reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
status = "okay";
mdio {
#address-cells = <1>;
#size-cells = <0>;
phy: ethernet-phy@0 {
reg = <0>;
qca,clk-out-frequency = <125000000>;
};
};
};
Currently the PHY node pointer is incorrectly associated with the
Ethernel controller instead of the PHY node itself.
This causes the PHY properties, such as "qca,clk-out-frequency" in
the example above to not get parsed.
Fix this problem by populating the phy_of_node node.
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Tom Rini <trini@konsulko.com>
The clock ouput frequency is calculated incorrectly for AR8035 due to
wrong masking of priv->clk_25m_reg and priv->clk_25m_mask.
This same issue has been already fixed in the kernel by:
commit b1f4c209d84057b6d40b939b6e4404854271d797
Author: Oleksij Rempel <o.rempel@pengutronix.de>
Date: Wed Apr 1 11:57:32 2020 +0200
net: phy: at803x: fix clock sink configuration on ATH8030 and ATH8035
The masks in priv->clk_25m_reg and priv->clk_25m_mask are one-bits-set
for the values that comprise the fields, not zero-bits-set.
This patch fixes the clock frequency configuration for ATH8030 and
ATH8035 Atheros PHYs by removing the erroneous "~".
To reproduce this bug, configure the PHY with the device tree binding
"qca,clk-out-frequency" and remove the machine specific PHY fixups.
Fixes: 2f664823a47021 ("net: phy: at803x: add device tree binding")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apply the same fix in the U-Boot driver.
Tested on a i.MX6 Hummingboard.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Tested-by: Tom Rini <trini@konsulko.com>
Add Kconfig entries for the pcnet driver and convert MIPS malta
to use those.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
With all the changes in place, add support for DM into the
pcnet driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Pull the common parts of functions out so they can be reused by both
DM and non-DM code paths. The recv() function had to be reworked to
fit into this scheme and this means it now only receives one packet
at a time instead of spinning in an endless loop.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Instead of using the non-DM-only name and enetaddr in struct eth_device,
add pointers into the private data which can either point to that non-DM
name or a DM one later on.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Instead of using the non-DM-only iobase in struct eth_device, add
one into the private data to make DM and non-DM operation possible.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Get rid of the global point to private data, and rather pass it
thought dev->priv. Also remove the unnecessary check for lp being
non-NULL, since it is always NULL at this point.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Instead of using eth_device priv for this PCI devbusfn, free it
so it could be used for driver private data, and wrap devbusfn
into those driver private data.
Note that using the name dev for the variable is a trick left for
later, when DM support is in place, so dm_pci_virt_to_mem() can be
used with minimal ifdeffery.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Remove those as they are not needed anymore.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Move the function at the end of the driver, so we could drop
various forward declarations later. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The private data allocation does not have to be done every time the
NIC is initialized at run time, move the allocation to initialize
function, which means it will be done only once when the driver
starts.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
This combination of functions can be replaced with calloc(),
make it so.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The current code is horribly complex. Both the RX and TX buffer
descriptors are 16 bytes in size, the init block is 32 bytes in
size, so simplify the code such that the entire private data of
the driver are allocated cache aligned and the RX and TX buffer
descriptors are part of the private data.
This removes multiple malloc calls and cache flushes.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Use this macro to fully fill the PCI device ID table. This is mandatory
for the DM PCI support, which checks all the fields.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
All of one PCNET users has this option set, make this default
and drop this config option.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Use struct pcnet_priv all over the place instead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Split the common code from the non-DM code, so it can be reused by
the DM code later. As always, the recv() function had to be split
into the actual receiving part and free_pkt part to fit with the
DM.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The RX/TX DMA descriptor rings are per-device-instance private data,
so move them into the private data.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Instead of doing ethernet device lookup by name every time there
is an MDIO access, pass the driver private data via mdiobus priv
to the MDIO bus accessors.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This patch replaces the various uses of struct eth_device for accessing
device private data with struct eepro100_priv, which is compatible both
with DM and non-DM operation.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is a trick in preparation for adding DM support. By passing in
the PCI BDF into the bus_to_phys()/phys_to_bus() macros and calling
that dev, we can substitute dev with udevice when DM support lands
and do minor adjustment to the macros to support both DM and non-DM
operation. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Drop the inline keyword from the static functions, the compiler has a
much better overview and can decide how to inline those functions much
better.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Those macros depended on specific variable names to be declared
at their usage sites, fix this by adding an argument to those
macros and also protect the argument with braces.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Pull the MII registration code into a separate function. Moreover,
properly free memory in case any of the registration or allocation
functions fail, so this fixes an existing memleak.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Use this macro to fully fill the PCI device ID table. This is mandatory
for the DM PCI support, which checks all the fields.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Move the functions around in the driver to prepare it for DM conversion.
Drop forward declarations which are not necessary anymore. No functional
change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Remove all the remaining use of the 'volatile' keyword, as this is
no longer required. All the accesses which might have needed this
use of 'volatile' have been repaired properly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Add cache invalidation and flushes wherever the DMA descriptors are
written or read, otherwise this driver cannot work reliably on any
systems where caches are enabled.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This code is replicated in the driver thrice almost verbatim, factor
it out into a separate function and clean it up. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The current eepro100 driver accesses its memory mapped registers directly
instead of using the standard I/O accessors. This can cause problems on
some systems as the accesses can get out of order. So convert the direct
volatile dereferences to use the normal in/out macros.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is automated cleanup via checkpatch, no functional change.
./scripts/checkpatch.pl --show-types -f drivers/net/eepro100.c
./scripts/checkpatch.pl --types INDENTED_LABEL -f --fix --fix-inplace drivers/net/eepro100.c
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is automated cleanup via checkpatch, no functional change.
./scripts/checkpatch.pl --show-types -f drivers/net/eepro100.c
./scripts/checkpatch.pl -f --fix --fix-inplace drivers/net/eepro100.c
This fixes all the remaining errors except a couple of comments which
are longer than 80 characters, all the volatile misuse and all the
camelcase, that needs a separate patch.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is automated cleanup via checkpatch, no functional change.
./scripts/checkpatch.pl --show-types -f drivers/net/eepro100.c
./scripts/checkpatch.pl --types INDENTED_LABEL -f --fix --fix-inplace drivers/net/eepro100.c
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is automated cleanup via checkpatch, no functional change.
./scripts/checkpatch.pl --show-types -f drivers/net/eepro100.c
./scripts/checkpatch.pl --types POINTER_LOCATION -f --fix --fix-inplace drivers/net/eepro100.c
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is automated cleanup via checkpatch, no functional change.
./scripts/checkpatch.pl --show-types -f drivers/net/eepro100.c
./scripts/checkpatch.pl --types PARENTHESIS_ALIGNMENT -f --fix --fix-inplace drivers/net/eepro100.c
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is automated cleanup via checkpatch, no functional change.
./scripts/checkpatch.pl --show-types -f drivers/net/eepro100.c
./scripts/checkpatch.pl --types BRACES -f --fix --fix-inplace drivers/net/eepro100.c
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is automated cleanup via checkpatch, no functional change.
./scripts/checkpatch.pl --show-types -f drivers/net/eepro100.c
./scripts/checkpatch.pl --types SPACING -f --fix --fix-inplace drivers/net/eepro100.c
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This code is never enabled, last board that used it was ELPPC which
was removed some 5 years ago, so just remove this code altogether.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
We generate a number of helper inline functions to make accesses easier.
However not all permutations of each function will be used and clang
will warn about unused ones. Decorate all of them with __maybe_unused
because of this.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Do not re-read the HW address from the EEPROM on every start of
transfer, otherwise the user will not be able to adjust ethaddr
as needed. Read the address only once, when the card is detected.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Use this macro to fully fill the PCI device ID table. This is mandatory
for the DM PCI support, which checks all the fields.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Split the driver into common and non-DM functionality, so that the
DM support can later re-use the common code, while we retain the
non-DM code until all the platforms are converted.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Instead of always calling rtl8139_eeprom_delay() with priv->ioaddr,
call it with priv and let the function access priv->ioaddr. This
reduces code duplication and has no impact, since the compiler will
inline this as needed anyway.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Introduce rtl8139_pdata, which is a super-structure around eth_device
and tracks per-device state, here the device IO address, PCI BDF, RX
and TX ring position. Pass this structure around instead of the old
non-DM eth_device in preparation for DM conversion.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
These macros depended on the dev variable being declared wherever
they were used. This is wrong and will not work with DM anyway, so
pass only the PCI BFD into these macros, which fixes the dependency
and prepares them for DM support as well.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Replace the use of custom static ioaddr variable with common dev->iobase,
no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Replace malloc()+memset() combination with calloc(), no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Pull the device name setting into a separate function, as this
will be shared between DM/non-DM variants.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Add the DP8382X generic PHY registration to the TI PHY init file.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
ti_phy_init function was allocated to the DP83867 PHY. This function
name is to generic for a specific PHY. The function can be moved to a
TI specific file that can register all TI PHYs that are defined in the
defconfig. The ti_phy_init file will contain all TI PHYs initialization
so that only phy_ti_init can be called from the framework.
In addition to the above the config flag for the DP83867 needs to be changed
in the Kconfig and dependent defconfig files. The config flag that was
used for the DP83867 was also generic in nature so a more specific
config flag for the DP83867 was created.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
There are devices accesible through mdio clause-45, such as
retimers, that do not have PMA or PCS blocks.
This patch adds MDIO_MMD_VEND1 on the list of device addresses
where phyid is searched. Previous order of devices was kept.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
This is a WAR for DHCP failure after rebooting from the L4T kernel. The
r8169.c kernel driver is setting bit 19 of the rt816x HW register 0xF0,
which goes by FuncEvent and MISC in various driver source/datasheets.
That bit is called RxDv_Gated_En in the r8169.c kernel driver. Clear it
here at the end of probe to ensure that U-Boot can get an IP assigned
via DHCP.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Linux commit 232ba3a51cc2 ('net: phy: Micrel KSZ8061: link failure after
cable connect') implements a fix for the above errata.
This patch replicates that errata fix in an ksz8061 specific init routine.
Signed-off-by: Bryan O'Donoghue <bod@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When an eTSEC is configured to use TBI, configuration of the
TBI is done through the MIIM registers for that eTSEC.
For example, if a TBI interface is required on eTSEC2, then
the MIIM registers starting at offset 0x2_5520 are used to
configure it.
Fixes: 9a1d6af55e ("net: tsec: Add driver model ethernet support")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The current code accesses eTSEC registers using physical
address directly, it's not correct, though no problem on
current platforms. It won't work on platforms, which does
not support 1:1 virtual-physical address map.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Allow the MDIO devices to be probed based on the device tree.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The H6 EMAC is very similar to the H3 variant, except that it uses the
same pinmux as R40. Add support for it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
While the R40 uses a different register for EMAC clock configuration
than other chips, the register has a very similar layout. Reuse the
existing bitfield definitions in this file, since they match.
This allows the driver to compile on the H6 platform, where the
CCM_GMAC_CTRL definitions are not present.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Convert CONFIG_KS8851_MLL and CONFIG_KS8851_MLL_BASEADDR to Kconfig
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Add support for U-Boot DM and DT probing.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Instead of reading out the entire FIFO and possibly overwriting U-Boot
memory, read out one packet per recv call, pass it to U-Boot network
stack, and repeat. It is however necessary to cache RXFC value, because
reading that one out clears it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Split network handling functions into non-DM specific parts and
common code in preparation for conversion to DM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Introduce a private data structure for this driver with embedded
struct eth_device and pass it around. This prepares the driver to
work with both DM and non-DM systems.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Fix various checkpatch complaints.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
There is only one chip ID in the table of chip IDs for this chip.
Read out the chip ID instead and mask off the last "revision" bit
to check the chip ID, this works for all chips in the family. Then
drop the chip ID passing around.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The packet status and length information should be extracted from the
FIFO per-packet. Adjust the code such that it reads the packet meta
data and then the packet afterward, if applicable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Most of the entries in the structure are useless, remove them. Inline
the rest of uses where applicable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Per KS8851-16MLL, the RXQCR is a 16bit register. Use 16bit accessors
to it consistently and drop the ks_wrreg8() function altogether, as
it is not used anymore.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The cached RXQCR value is never updated, remove the cache and just use
the bits in the cache directly in the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Replace combination of malloc()+memset() with calloc() as the behavior
is exactly the same and the amount of code is reduced. Moreover, remove
printf() in the fail path, as it is useless, and return proper -ENOMEM
return code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
- Add DM_ETH support for lx2160aqds, ls2080aqds, ls1088aqds
- QSI related fixes on ls1012a, ls2080a, ls1046a, ls1088a, ls1043a based
platforms
- Bug-fixes/updtaes related to ls1046afrwy, fsl-mc, msi-map property
The DPC fixup for MAC address and enet_if is not made if
/board/ports node is missing in DPC file.
Add /board/ports or /ports nodes if them are missing.
Signed-off-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
Reviewed-by: Ioana Ciornei <Ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Similarly to iommu-map, the msi-map property must also be fixed up
in the device tree, in order for the icid -> streamid translation
be possible in the MSI case as well.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Diana Craciun <diana.craciun@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Bus callback functions for read/write/reset need to be set only for
DM_ETH, moving endif a bit lower.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
This requires quite a few header-file additions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Have this symbol follow the pattern of all other such symbols.
This patch also removes a TODO from the code.
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Have this symbol follow the pattern of all other such symbols.
This patch removes a TODO from the code.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
As per Linux's driver, ID_MODE_DIS is only set when the PHY interface is
RGMII. Don't enable it for the rest of setups.
This has been seen to misconfigure RPi4's PHY when booting Linux.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Implement the read_rom_hwaddr callback to load MAC address from fuse
for imx8m platforms.
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
imx_get_mac_from_fuse is used to load MAC address from fuse. On imx8mp,
we have two different ENET controllers and both need to call this
function. So decouple its declare from fec driver.
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Implement the callbacks to get phy mode interface and txclk
rate configuration.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add dwc eqos for imx support.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add RX delay enable support for RTL8211F PHY.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
For dual ethernet controllers, the HW design may connect ETH phys to
one MDIO ports. So two different ethernet drivers have to share MDIO bus.
Since two ethernet drivers are independent, we can't ensure their probe
order.
To resolve this problem, introduce an eth phy generic driver and uclass.
After eth-uclass binds, we search the mdio node and binds the phy node
with the eth-phy-generic driver.
When one eth driver get its phy device, the parent of phy device will
probe prior than phy device. So this ensure the eth driver ownes the
MDIO bus will be probed before using its MDIO.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add fuse check for fec. If the fuse indicates the module
will not work in the SoC, let's fail the initialization.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In RGMII mode the 10Mbps link speed is supported only when CPSW2G MAC SL is
configured for External Control ("in band") mode
CPSW_PN_MAC_CONTROL_REG.CTL_EN(18) = 1
Hence update am65_cpsw_update_link() to follow documentation.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
The two functions are now exactly the same, remove one of them.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
We can configure the clock output in the device tree. Disable the
hardcoded one in here. This is highly board-specific and should have
never been enabled in the PHY driver.
If bisecting shows that this commit breaks your board it probably
depends on the clock output of your Atheros AR8035 PHY. Please have a
look at doc/device-tree-bindings/net/phy/atheros.txt. You need to set
"clk-out-frequency = <125000000>" because that value was the hardcoded
value until this commit.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add support for configuring the CLK_25M pin as well as the RGMII I/O
voltage by the device tree.
By default the AT803x PHYs outputs the 25MHz clock of the XTAL input.
But this output can also be changed by software to other frequencies.
This commit introduces a generic way to configure this output.
Also the PHY supports different RGMII I/O voltages: 1.5V, 1.8V and 2.5V.
An internal LDO is able to provide 1.5V (default) and 1.8V. The 2.5V
option needs an external supply voltage. This commit adds support to
switch the internal LDO to 1.8V.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Provide functions to read and write the Atheros debug registers.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Debug register 5 contains TX_CLK DELAY at bit 8 and reserved values at
the other bit positions, just like the other PHYs in the family do.
Therefore, it is not necessary to hardcode the reserved values, but
instead simply follow the read-modify-write procedure from the common
function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
To eliminate any doubts about the out-of-reset value of the PHY, that
the driver previously relied on.
If bisecting shows that this commit breaks your board you probably have
a wrong PHY interface mode. You probably want the
PHY_INTERFACE_MODE_RGMII_RXID or PHY_INTERFACE_MODE_RGMII_ID mode.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Also take the opportunity to use the phy_read_mmd and phy_write_mmd
convenience functions.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Delete the extraneous write to debug reg 5 that enables Tx delay
When the driver was originally introduced in commit "6027384a phylib:
Add Atheros AR8035 GETH PHY support", the Tx delay was being
unconditionally enabled.
Then during "2ec4d10b phy: atheros: add support for RGMII_ID, RGMII_TXID
and RGMII_RXID", the author did not notice that code for enabling Tx
delay code was already. Therefore, the if condition for Tx delay has
always been useless for this PHY since this commit introduced it.
Prior to this patch, every AR8035 PHY in U-boot had Tx delay enabled.
After this patch, only those who define the interface as RGMII_TXID or
RGMII_ID will. This is to be expected, but will nonetheless break the
setups of those who didn't know they rely on Tx delay implicitly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Commit 69529c9120 ("net: pcnet: Switch to PCI memory access")
switched from PCI IO access to PCI memory access without updating
the I/O primitives. Contrary to SH, the primitives for memory
access and IO access are implemented differently. Thus doing
memory access with IO port primitives breaks the driver on
MIPS Malta board.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add support for U-Boot DM and DT probing. Furthermore, build the
SMC911x standalone EEPROM example only for the non-DM case, as it
is not converted yet.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch enables the possibility to set FEC_ENET_ENABLE_TXC_DELAY or
FEC_ENET_ENABLE_RXC_DELAY so one can via a define enable the RXC or TXC
delay in the MAC.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Split network handling functions into non-DM specific parts and
common code in preparation for conversion to DM.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Invert the status handling logic in smc911x_recv(), to make the
function easier to read, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Introduce a private data structure for this driver with embedded
struct eth_device and pass it around. This prepares the driver to
work with both DM and non-DM systems.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Convert the IO accessors to standard ones instead of using volatile
void pointers, as those do not cover all the bus access details.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
These accessors are not overridden by any board, and even if they were,
this is something which should be handled via DM now, so remove the
weak alias option. Moreover, drop the inline keyword, as the compiler
can decide better.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Inline all the functions from the header file, as they are not used
outside of the driver or the standalone EEPROM example.
Note that this does introduce considerable amount of duplication in
the standalone EEPROM example, however that one has to be rewritten
anyway, roughly such that the SMC911x driver would expose DM EEPROM
interface and the standalone example would use that.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Pull the MII interface registration into separate function to avoid the
ifdeffery in smc911x_initialize(). Moreover, adjust the fail path such
that we use goto labels.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Fix memleak in the init fail path, where if allocation or registration
of MDIO bus fails, then ethernet interface is not unregistered and the
private data are not freed, yet the probe function reports a failure.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Invert the logic in the aforementioned functions to reduce indent,
no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Rename the function to keep the naming scheme consistent,
no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Replace combination of malloc()+memset() with calloc() as the behavior
is exactly the same and the amount of code is reduced.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
These functions are never used and are likely a pre-DM remnant
from times long past, just remove them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
The rtl8139 driver is derived from Etherboot driver, which is in
turn derived from Linux 8139too driver added in Linux 2.2.18pre14.
An undocumented change in Linux 2.4.10.2 added a new field to the
driver, MODULE_LICENSE("GPL"); . According to current Linux kernel
licensing rules, Documentation/process/license-rules.rst, quote:
"GPL" Module is licensed under GPL version 2. This
does not express any distinction between
GPL-2.0-only or GPL-2.0-or-later. The exact
license information can only be determined
via the license information in the
corresponding source files.
And since the code does not contain any "future" clause, the tag
is therefore GPL-2.0 only.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Just move functions around in preparation for easy DM conversion,
rename rtl_bcast_addr() to rtl8139_bcast_addr(), no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Finish the checkpatch cleanup of the driver, fix the remaining issues
in probe and init function and in global variables, rename the probe
function to rtl8139_init(), no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
This hardware reset and reset-wait implementation was twice in the
driver, factor it out into a separate function. This really should
use wait_for_bit() eventually and return -ETIMEDOUT, but thus far,
handling of any of this is missing from the driver. This must be
added later. Thus far, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_stop(), clean up checkpatch errors in
the stop polling function. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_recv(), clean up various checkpatch errors,
line-over-80 conditions, and malformed comments. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_send(), clean up the TX polling, the TX
OK condition at the end, overuse of typecasts, and various line-over-80
problems. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_reset(), clean up the reset polling
and various line-over-80 problems. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_set_rx_mode(), use unsigned variables
where applicable and inline mc_filter[] values. No functional chanage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
This string of macros is exactly the same thing as rtl8139_rx_config,
so just use rtl8139_rx_config. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_read_eeprom() to keep the naming
consistent, keep the variables sorted in reverse xmas tree. No
functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The macro assumes ee_addr variable to be present when it's being
used. Rework the macro into a function instead and pass it an
argument specifying the register base address, to make it future
proof for DM conversion.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the horrible register definitions in the RTL8139 driver.
This does create a couple of checkpatch errors, but the driver is
full of them anyway, and those will be cleaned up later.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The DMA may attempt to write a DMA descriptor in the ring while it is
being updated. By writing the DMA descriptor buffer address to 0, it
is assured the DMA will not use such a buffer and the buffer can be
updated without any interference.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
This patch prevents an issue where the RX packet might have been
accessed by the CPU, which now has cached data from the packet in
the caches and possibly various write buffers, and these data may
be evicted from the caches into the DRAM while the buffer is also
written by the DMA.
By invalidating the buffer after the CPU accessed it and before the
DMA populates the buffer, it is assured that the buffer will not be
corrupted.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
The current code polls the RX desciptor ring for new packets by reading
the RX descriptor status. This works by accident, as the RX descriptors
are often in non-cacheable memory. However, the driver does support use
of RX descriptors in cacheable memory.
This patch adds a missing RX descriptor invalidation, which assures the
CPU will read a fresh copy of the RX descriptor instead of a cached one.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Currently the code only flushes the first RX descriptor, not every entry
in the RX descriptor ring. Fix this, to make sure the DMA engine can pick
the RX descriptors correctly.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
This code programs the next descriptor in the TX descriptor ring into
the hardware as the last valid TX descriptor. The problem is that if
the currenty descriptor is the last one in the array, the code will
not wrap around correctly and use TX descriptor 0 again, but instead
will use TX descriptor at address right past the TX descriptor ring,
which is the first descriptor in the RX ring.
Fix this by adding the necessary wrap-around.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
The RX descriptor field 3 should contain only OWN and BUF1V bits before
being used for receiving data by the DMA engine. However, right now, if
the descriptor was already used for receiving data and is being cleared,
the field 3 is only modified and the aforementioned two bits are ORRed
into the field. This could lead to a residual dirty bits being left in
the field 3 from previous transfer, and it generally does. Fully set the
field 3 instead to clear those residual dirty bits.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Replace the adhoc debugging ifdeffery with debug_cond() and an
internal SROM_DEBUG macro to select the debug level.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Move the functions in the driver around to better fit future DM
conversion, drop function forward declarations. No functional
change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename these functions to dc2114x_{inl,outl}(), use u32 values in
them instead of plain signed integers as all those values are in
fact register values and the driver code does bitwise operations
on them. No functional change intended.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Replace these macros with static functions to permit the compiler to
do type checking on the functions. The INL()/OUTL() functions have to
be moved in this patch as well, as those DE4X5 macros are using them.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the remaining driver code, macro space alignment, function
declaration indent, replace __attribute__((aligned(32))) with plain
__aligned(32). No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the SROM accessors to bring them up to standards with
U-Boot coding style. Sort variable into reverse xmas tree. No
functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the send_setup_frame() to bring it up to standards with
U-Boot coding style, invert the loops where applicable to cut
down the level of indent. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the driver halt code to bring it up to standards with
U-Boot coding style. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the driver recv code to bring it up to standards with
U-Boot coding style. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the driver send code to bring it up to standards with
U-Boot coding style, invert the loops where applicable to cut
down the level of indent. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the driver init code to bring it up to standards with
U-Boot coding style, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Replace the PCI IO access with PCI memory access, the card
supports both, but the former does not work with QEMU SH4.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Replace mips-specific UNCACHED_SDRAM() macro with standard
map_physmem(), which permits the driver to work on other
systems than mips.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
These macros are not used by any board, remove them to simplify
the driver. The EEPROM accessors are still retained however, as
those might still be useful.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
These macros guard one switch-case statement, which grows mips malta
by some 20 bytes if debug is enabled, and even less if it is not. To
make the code simpler, just support all the NICs and be done with it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Probe the FMan MACs based on the device tree while
retaining the legacy code/functionality.
One notable change introduced here is that, for DM_ETH,
the name of the interfaces is corrected to the fmX-macY
format, that avoids the referral to the MAC block names
which were incorrect for FMan v3 devices (i.e. DTSEC,
TGEC) and had weird formatting (i.e. FM1@DTSEC6, FM1@TGEC1).
The legacy code is left unchanged in this respect.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Allow the MDIO devices to be probed based on the device tree.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move the receive buffer free code in a separate function.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Make any adjustments necessary in order to support DPAA2 devices probed
using CONFIG_DM_ETH. While at it, fixup some styling issues aroung the
switch-case statement.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When CONFIG_DM_ETH is enabled DPAA2 network interfaces will now probe
based on DTS nodes with the "fsl,qoriq-mc-dpmac" compatible.
In this case, transform the ldpaa_eth driver into a UCLASS_ETH driver
and reuse the _open()/_tx()/_stop() functions already inplemented.
For the moment, the ldpaa_eth driver will support both configurations:
with or without CONFIG_DM_ETH enabled. Any 'struct eth_device' occurrence
now has a matching 'struct udevice' made mutually exclusive based on the
state of CONFIG_DM_ETH.
Signed-off-by: Florin Laurentiu Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add a driver for the MDIO interface integrated in the mEMAC (Multi-rate
Ethernet Media Access Controller) and the Fman 10G Ethernet MACs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
mt7531 is a 7-ports switch with 5 embedded giga phys, and uses the same
MAC design of mt7530. The cpu port6 supports SGMII only. The cpu port5
supports RGMII or SGMII in different model.
mt7531 is connected to mt7622 via both RGMII and SGMII interfaces.
In this patch, mt7531 cpu port5 or port6 is configured to maximum
capability to align CPU MAC setting.
The dts has been committed in the commit 6efa450565 ("arm: dts:
mediatek: add ethernet and sgmii dts node for mt7622")
Signed-off-by: Landen Chao <landen.chao@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
If CONFIG_CMD_NAND is disabled, get_nand_dev_by_index() is not
accessible.
This fix allows the build to succeed in this case.
Signed-off-by: Francois Gervais <fgervais@distech-controls.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add management of property "reg" to configure @ of phy and
also "max-speed" property to specify maximum speed in Mbit/s
supported by the device
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add management of property "reset-gpios" in the node identified by
"phy-handle" to configure any GPIO used to reset the PHY.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Reviewed-by: Patrice CHOTARD <patrice.chotard@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Not all IPs have private MDIO bus and MDIO bus should be shared between
several IPs. In past one patch tried to implement it
(https://lists.denx.de/pipermail/u-boot/2018-February/319285.html)
in pretty raw way but it is not the cleanest solution.
This patch is just taking the part of that solution to be able to handle it
over releases without conflicts.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add cache flush to zynq_gem_free_pkt. This is necessary
because some net routines would modify this buffer in place.
The cache_invalidate in the zynq_gem_recv function would cause
the modifications to the buffer to overwrite the DMA from the GEM,
if cache coherency is not enabled in the GEM, the next time the
buffer is in use.
Flushing the cache when the buffer is no longer in use by the
net functions ensures that the GEM DMA is going to take place
into a clean buffer.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
To access the PHY, the MAC registers must be initialized. Call the init
function in probe() to make it so, otherwise the PHY ID readout returns
all zeroes.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
When MACB_ZYNQ is enabled there is compilation warnings
drivers/net/macb.c: In function ‘_macb_init’:
drivers/net/macb.h:675:33: error: ‘MACB_DMACFG’ undeclared (first use in this function);
did you mean ‘MACB_MCF’?
writel((value), (port)->regs + MACB_##reg)
^~~~~
It has been caused by changing macros name by commit below.
Fixes: 6c636514d4 ("net: macb: sync header definitions as taken from Linux")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The correct setting for the RGMII ports on LS1046ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID. There is a pull-up that turns
on Rx internal delay by default and the u-boot does not
override that (yet) so in u-boot the interface is functional.
In Linux the PHY driver is clearing the Rx delay for the
"rgmii-txid" mode and the reception does not work.
Changing the RGMII mode to internal delay here ensures that
device tree fix-ups for the PHY connection type turn on both
Tx and Rx internal delay in Linux.
Fixes: cc1aa218f5 ("armv8/ls1046a: RGMII PHY requires internal
delay on Tx")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The correct setting for the RGMII ports on LS1043ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID. There is a pull-up that turns
on Rx internal delay by default and the u-boot does not
override that (yet) so in u-boot the interface is functional.
In Linux the PHY driver is clearing the Rx delay for the
"rgmii-txid" mode and the reception does not work.
Changing the RGMII mode to internal delay here ensures that
device tree fix-ups for the PHY connection type turn on both
Tx and Rx internal delay in Linux.
Fixes: 5a78a472f6 ("armv8/ls1043a: RGMII PHY requires internal
delay on Tx")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The RGMII modes that include internal delay were not all
properly treated in the memac code. Add support for all
RGMII delay modes.
Fixes: 111fd19e3b ("fm/mEMAC: add mEMAC frame work")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The PHY models of the Marvell 88E151x series are not reliably
distinguishable by their uid / PHY identifiers.
The 88E1510, 88E1512, 88E1514 and 88E1518 all have the same OUI and
model number and bits 3:0 in the PHY Identifier 2 (Page 0, Reg 3) are
described as HW revision number, but both 88E1510 and 88E1518 PHYs were
observed with the same HW rev number (1).
Before commit 83cfbeb0df ("net: phy: Fix mask so that we can identify
Marvell 88E1518"), the 88E151x were detected because the HW revision
bits were masked from the uid. After that change, 88E1510/12/18 were all
detected as 88E1518 and the 88E1510 specific code was no longer run.
I modified the mask to again ignore all four HW revision bits, removed
the 88E1510 specific code (board-specific LED/INTn setup), which was not
called since late 2016 anyway and renamed the config function and
phy_driver struct to the better fitting 88e151x.
The uid and mask bits 3:0 are now again the same as in the Linux kernel.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
This patch adds ability to switch beetween two PHY SGMII modes.
Some hardware, for example, FPGA IP designs may use 6-wire mode
which enables differential SGMII clock to MAC.
Patch description, dt flags have been done in mainline Linux by
commit a2111c460c0c ("net: phy: dp83867: Add documentation for SGMII mode type")
and by commit 507ddd5c0d47 ("net: phy: dp83867: Add SGMII mode type switching")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Commit 27c3f70f3b ("net: phy: Increase link up delay in
genphy_update_link()") increased the per-iteration waiting time from
1ms to 50ms, without adjusting the timeout counter. This lead to the
timeout increasing from the typical 4 seconds to over three minutes.
Adjust the timeout counter evaluation by that factor of 50 to bring the
timeout back to the intended value.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Fixes: net: phy: Increase link up delay in genphy_update_link() ("27c3f70f3b50")
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Matthias Brugger <mbrugger@suse.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The driver now unconditionally prints some information that's not
universally useful. Replace printf with debug.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use either USXGMII or XFI in aquantia_set_proto and drop XGMII as a valid
protocol configuration. The PHY doesn't support it, it's just used as an
alias for one of the other two protocols.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add NC-SI to the usual phy handling. This makes two notable changes:
- Somewhat similar to a fixed phy, phy_connect() will create an NC-SI
phy if CONFIG_PHY_NCSI is defined.
- An early return is added to phy_read() and phy_write() to handle a
case like the NC-SI phy which does not define a bus.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This introduces support for the NC-SI protocol, modelled as a phy driver
for other ethernet drivers to consume.
NC-SI (Network Controller Sideband Interface) is a protocol to manage a
sideband connection to a proper network interface, for example a BMC
(Baseboard Management Controller) sharing the NIC of the host system.
Probing and configuration occurs by communicating with the "remote" NIC
via NC-SI control frames (Ethernet header 0x88f8).
This implementation is roughly based on the upstream Linux
implementation[0], with a reduced feature set and an emphasis on getting
a link up as fast as possible rather than probing the full possible
topology of the bus.
The current phy model relies on the network being "up", sending NC-SI
command frames via net_send_packet() and receiving them from the
net_loop() loop (added in a following patch).
The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent
field definitions.
[0]: https://github.com/torvalds/linux/tree/master/net/ncsi
[1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Driver probe function is called again and again in case of error.
Malloc space is getting full which is is reported by:
Insufficient RAM for page table: 0x15000 > 0x14000.
Please increase the size in get_page_table_size()
### ERROR ### Please RESET the board ###
The patch is freeing allocated buffers on error path to avoid panic.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
On Xilinx ZynqMP revA board initial value of PHYCR register is 0x5448 which
means FORCE_LINK_GOOD is already setup. Origin code was doing write but the
new code is doing read/modify/write and keep this bit untouched. That's why
ethernet stop to work.
The patch is cleaning this bit when PHYCR value is composed.
Tested on Xilinx zcu102-revA and zcu104-rev1.0 boards.
Fixes: 37d6265f2b ("net: phy: dp83867: refactor rgmii configuration")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
flush_dcache_range() expects unsigned long in the arguments. Here u32
variable is unable to hold the higher address value when ddr mapped
to higher addresses & flushing lower address dchache range instead
which is unmapped causing to crash.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The implementation of dma_map_single() and dma_unmap_single() is
exactly the same for all the architectures that support them.
Factor them out to <linux/dma-mapping.h>, and make all drivers to
include <linux/dma-mapping.h> instead of <asm/dma-mapping.h>.
If we need to differentiate them for some architectures, we can
move the generic definitions to <asm-generic/dma-mapping.h>.
Add some comments to the helpers. The concept is quite similar to
the DMA-API of Linux kernel. Drivers are agnostic about what is
going on behind the scene. Just call dma_map_single() before the
DMA, and dma_unmap_single() after it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl48iogACgkQfxc6PpAI
reaVzAf/an3/yKe6r3CVWlcRV6H/dVg1ApnnLpX7jS0p0b++oCVvOiy7z1WPXj3k
b1SSgENDeeZ/8EHio+Gf7ZidH/TGEj7L6YEFwd1t60GMkZiWEkNf4Z53tw482YG+
96hoPD+ySTW+ddIdVHWAFG2I4aEiKHANJAp/ItNdD+rLbrEwNQy+eiK5JTOk80B6
/X8AJCLZeAC1s7vs+2+WolgjT78QGzA9HHalMiublcqh0ivKKk0QeQiOKKPe8JYJ
om5YY1TxayQ60Xmo5f39/SBfzEEklxw83sU9o1tBeYzyVUpu7fQdkxiDbWdsij77
DgwLdeYQJGbN+hdSWE0gjTqyhW+lWA==
=KRoA
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-6feb20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
sandbox conversion to SDL2
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
building mtk ethernet driver for aarch64 (mt7622) results
in warnings/errors
"error: cast from pointer to integer of different size"
Fixes: 23f17164d9 ("ethernet: MediaTek: add ethernet driver for MediaTek ARM-based SoCs")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
This patch add sgmii init part for the mediatek SoC that
support sgmii mode. It is a must for mt7622.
Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
- add dfu support to dwc2 for bcm2835
- enable DFU for RPi4
- Fix RPi4 memory map to include the genet device
- add driver for the genet ethernet device
- enable network support in RPi4 config
-----BEGIN PGP SIGNATURE-----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=Sv9b
-----END PGP SIGNATURE-----
Merge tag 'rpi-next-2020.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-raspberrypi
- DFU support file operations lager then the default max size
- add dfu support to dwc2 for bcm2835
- enable DFU for RPi4
- Fix RPi4 memory map to include the genet device
- add driver for the genet ethernet device
- enable network support in RPi4 config
The Broadcom GENET Ethernet MACs are used in several MIPS based SoCs
and in the Broadcom 2711/2838 SoC used on the Raspberry Pi 4.
There is no publicly available documentation, so this driver is based
on the Linux driver. Compared to that the queue management is
drastically simplified, also we only support version 5 of the IP and
RGMII connections between MAC and PHY, as used on the RPi4.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
[Andre: heavy cleanup and a few fixes]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Now that arch specific dma mapping APIs take care of cache
flush/invalidate, drop local cache flush operation.
While at that fix dma_unmap_single() call to match new prototype
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Separate MAC and serdes configuration, MAC configuration must be applied
at each enetc_start() as FLR clears it.
This restores traffic for ENETC interfaces in USXGMII mode.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The LS1028A SoC is special in the handling of the MAC addresses. We need
to write to the IERB version of the PSIPMAR0/1 register. This value will
be sampled into the corresponding port PSIPMAR0/1 register if the PCI
memory access is enabled.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Intead of setting the MAC address in enetc_start() use the proper
write_hwaddr(). U-Boot takes care of the random MAC address, too.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Passes on the primary address used by u-boot to Linux. The code does a DT
fix-up for ENETC PFs and sets the primary MAC address in IERB. The address
in IERB is restored on ENETC PCI functions at FLR.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
These three clock functions don't use driver model and should be migrated.
In the meantime, create a new file to hold them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add specific dm code, but maintaining this driver as is, so more in the
shape of a mii library. Can be moved to dm in a further step.
Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
Bring in the following merges:
commit 8fbbec12f7
Merge: 87f69f467a63618e71e8
Author: Tom Rini <trini@konsulko.com>
Date: Fri Jan 3 09:48:47 2020 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq into next
- updates and fixes on ls1028a, lx2, ls1046a, MC-DPSPARSER support
commit 87f69f467a
Merge: c0912f9bbf4466b99703
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 24 08:18:19 2019 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx into next
- Enable DM driver on ppc/km boards
- Enable DM_USB for some of NXP powerpc platforms: P5040, T4240, T208x,
T104x, P4080, P2041, P2020, P1020, P3041
- Some updates in mpc85xx-ddr driver, km boards
commit c0912f9bbf
Merge: 533c9f5714a1d6dc3f84
Author: Tom Rini <trini@konsulko.com>
Date: Wed Dec 18 07:20:19 2019 -0500
Merge branch 'next' of https://gitlab.denx.de/u-boot/custodians/u-boot-x86 into next
- Various x86 common codes updated for TPL/SPL
- I2C designware driver updated for PCI
- ICH SPI driver updated to support Apollo Lake
- Add Intel FSP2 base support
- Intel Apollo Lake platform specific drivers support
- Add a new board Google Chromebook Coral
commit 533c9f5714
Merge: 553cb06887033e18b47b
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 17 07:53:08 2019 -0500
Merge tag '20191217-for-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c into next
i2c: for next
- misc: i2c_eeprom:
Add partition support and add ability to query size
of eeprom device and partitions
- i2c common:
add support for offset overflow in to address and add
sandbox tests for it.
commit 553cb06887
Merge: f39abbbc53b4f98b3b16
Author: Tom Rini <trini@konsulko.com>
Date: Thu Dec 12 08:18:59 2019 -0500
Merge tag 'dm-next-13dec19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm into next
buildman improvements including toolchain environment feature
sandbox unicode support in serial
Add support for DPSPARSER object (create/destroy, open/close, apply spb)
which is required to configure Soft Parser by using MC.
Also add uboot command to apply Soft Parser Blob with command:
fsl_mc apply spb <spb_load_addr>
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Passing 0 to PHY connect used to trigger a MDIO scan due to a bug fixed in
the meantime. It's unclear if bcm-sf2 wants to connect to PHY @ addr 0 or
is scanning the bus, passing -1 here should keep it functional either way.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Cc: Jiandong Zheng <jdzheng@broadcom.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
PHY address 0 is a valid PHY address, to scan for all PHYs, pass -1 to
phy_connect(). Passing 0 used to work before be accident, but does no
longer.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
At present if CONFIG_SPL_GPIO_SUPPORT is enabled then the GPIO uclass
is included in SPL/TPL without any control for boards. Some boards may
want to disable this to reduce code size where GPIOs are not needed in
SPL or TPL.
Add a new Kconfig option to permit this. Default it to 'y' so that
existing boards work correctly.
Change existing uses of CONFIG_DM_GPIO to CONFIG_IS_ENABLED(DM_GPIO) to
preserve the current behaviour. Also update the 74x164 GPIO driver since
it cannot build with SPL.
This allows us to remove the hacks in config_uncmd_spl.h and
Makefile.uncmd_spl (eventually those files should be removed).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Get flow ID information for RX DMA channel using dma_get_cfg() interface
instead of reading from DT. This is required in order to avoid DT update
whenever there is change in the range of flow ID allocated to the host.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Fixes: e766849713 ("net: ftgmac100: convert the RX/TX descriptor arrays")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This bus is used to access internal SoC PHYs. These PHYs are configured
by the ENETC driver directly, but it's useful to have command line access
to this MDIO to debug the system especially when using new external PHYs.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
On some boards MDIO may get stuck if it detects echo on the line. This is
a know hardware issue, there is a board fix for it. In case we're running
on a board that doesn't have the fix, we don't want to loop here forever
and freeze U-Boot.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This reduces the time needed to establish a link as we don't reset the link
each time the interface is used. Our Link capabilities do not change at
run-time so there is no need to re-apply PHY configuration each time.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The original code enabled link speeds up to 1Gbps, but the interface can
go up to 2.5G, enable that speed to in PHY AN mask.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Uses the new dm_eth_phy_connect helper to connect to the PHY to simplify
the code.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In some cases the link on the system interface of the aquantia PHY comes up
after the link on line interface. The link state loop only checks the line
side, which may result in first packet sent being lost.
Use aquantia_link_is_up instead, which checks both system and line side on
gen 2/3 PHYs to avoid losing the 1st packet.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Aquantia PHYs have a SMBus interface mostly used for debug. The addresses
on this interface are normally set up by PHY firmware, but depending on the
board they may end up not being unique. Add an optional DT property used
to change SMBus address if needed.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
MDI pins up to the RJ45 connector may be reversed on the board and the
default PHY configuration applied by firmware may or may not match that.
Add an optional DT property to configure MDI reversal for this case.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If PHY is not ready for data by the time _config is called, reconfigure the
PHY system interface to use the proper protocol based on phydev->interface,
just in case the defaults set by PHY firmware don't match current
configuration.
Signed-off-by: Florin Laurentiu Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Uses the data field in phy_driver structure to identify the PHY generation.
This is useful for custom configuration as non-generic PHY registers are
not 100% compatible between generations.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The PHY supports XFI and USXGMII, the notable difference being that USX AN
is enabled for USXGMII. Legacy code uses XGMII for any 10G proto and
detects whether USX AN should be enabled or not using a PHY status
register. Keep that functionality too, so we don't break existing drivers.
Signed-off-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fix vendor name in MV88E61xx option description.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Support probing and init for 88E6071 switch.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
On mv88E6071 the 'EDet' field offset, width and sense control
bits are different, adjust the driver to init the PHY control
register as needed. This fixes not working link detection and
tftp transfers.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
On 88E6071 chip the port status register bit field offsets
for duplex and link bits differ. Extend the driver to use
88E6071 specific offset values. The width of bit fields for
speed status differ, too. Adapt for proper port speed
detection on 88E6071.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Extend the driver to init switch register offsets from variables
instead of compile time macros and enable detection of 88E6071 and
compatible devices. Ethernet transfer (e.g. tftp) does not work yet,
so enable the registration of the 'indirect mii' bus for easier PHY
register access by 'mii' command.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The KSZ8081 PHY has a factory test mode which is set at the de-assertion
of the reset line based on the RXER (KSZ8081RNA/RND) or TXC
(KSZ8081MNX/RNB) pin. If a pull-down is missing, or if the pin has a
pull-up, the factory test mode should be cleared by manually writing a 0
(according to the datasheet).
Create another ksz8081_config function to handle this case.
Suggested-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Aquantia quad-phys may take longer to initialize. This commit adds
a polling mechanism for a global alarm bit that tells if phy init
sequence is completed.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This allows passing arbitrary addresses through macb_miiphy_read and
macb_miiphy_write, therefore enabling the mii command to access
all mdio bus devices instead of only the defined phy.
Signed-off-by: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
To support accessing arbitrary addresses the mii/mdio bus it is
necessary that the macb_mdio_read and macb_mdio_write functions
do not implicitly use the address of the connected phy.
The function signature is extended according to the Linux kernel
equivalent.
Signed-off-by: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
I've noticed that in most cases when genphy_update_link() is called, the
ethernet driver (mt7628-eth in this case) fails with the first ethernet
packets. Resulting in a timeout of the first tftp command. Increasing
the delay in the link check look from 1 to 50 ms and moving it below the
BMSR register read fixes this issue, resulting in a stable ethernet
traffic, even after initial link autonogotiation.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This version of the RTL-8168 chip can be found on some add-in cards sold
by CSL-Computer GmbH & Co. KG. The chip isn't special in any way, but it
needs to have the ChipCmd register programmed after the DMA descriptors
have been set up, so make sure that happens by adding an entry to the
chip information table.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Changes to mvpp2.c require the MVMDIO module which in turn uses
DM_MDIO.
Signed-off-by: Nevo Hed <nhed+github@starry.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit ports mvpp2 to use the recently introduced Marvell MDIO
(MVMDIO) driver. It removes direct interaction with the SMI & XSMI
busses. This commit is based in part on earlier work by
Ken Ma <make@marvell.com> in Marvell's own downstream repo:
https://github.com/MarvellEmbeddedProcessors/u-boot-marvell/commit/c81dc39.
The above refrenced work was based on an MVMDIO implementation that
never made it into U-Boot. With this patch the mvpp2 driver switches
to use the new MVMDIO driver that is based on a more universal
mdio-uclass implementation.
Signed-off-by: Nevo Hed <nhed+github@starry.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If the phy doesn't match with any existing u-boot drivers, the phy
framework will connect it to the generic one which uid ==
0xffffffff. In this case, act as if the phy wouldn't be declared in
dts. Otherwise, in case of 3310 (for which the driver doesn't exist)
the link is marked as always down. Removing phy entry from dts in case
of 3310 is not a good option because it is required for the
phy_fw_down procedure.
This patch fixes the issue with the link always down on MCBIN board.
nhed: added NULL deref test.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Tested-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Nevo Hed <nhed+github@starry.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Issue:
- Network stuck if autonegotion fails.
Issue root cause:
- When autonegotiation fails during port open procedure, the packet
processor configuration does not finish and open procedure exits
with error.
- However, this doesn't prevent u-boot network framework from
calling send and receive procedures.
- Using transmit and receive functions of misconfigured packet
processor will cause traffic to get stuck.
Fix:
- Continue packet processor configuration even if autonegotiation
fails. Only error message is triggered in this case.
- Exit transmit and receive functions if there is no PHY link
indication.
- U-boot network framework now calls open procedure again during next
transmit initiation.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Tested-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Refactor SGMII configuration to group all settings together and reduce
number of MDIO transactions.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Based on commit 27708eb5481b ("net: phy: dp83867: IO impedance is not
dependent on RGMII delay") of mainline linux kernel.
The driver would only set the IO impedance value when RGMII internal delays
were enabled. There is no reason for this. Move the IO impedance block
out of the RGMII delay block.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Based on commit c11669a2757e ("net: phy: dp83867: Rework delay rgmii delay
handling") of mainline linux kernel.
The current code is assuming the reset default of the delay control
register was to have delay disabled. This is what the datasheet shows as
the register's initial value. However, that's not actually true: the
default is controlled by the PHY's pin strapping.
This patch:
- insures the other direction's delay is disabled If the interface mode is
selected as RX or TX delay only
- validates the delay values and fail if they are not in range
- checks if the board is strapped to have a delay and is configured to use
"rgmii" mode and warning is generated that "rgmii-id" should have been
used.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Based on commit 13c83cf8af0d ("net: phy: dp83867: Add ability to disable
output clock") of mainline linux kernel.
Generally, the output clock pin is only used for testing and only serves as
a source of RF noise after this. It could be used to daisy-chain PHYs, but
this is uncommon. Since the PHY can disable the output, make doing so an
option. I do this by adding another enumeration to the allowed values of
ti,clk-output-sel.
The code was not using the value DP83867_CLK_O_SEL_REF_CLK as one might
expect: to select the REF_CLK as the output. Rather it meant "keep clock
output setting as is", which, depending on PHY strapping, might not be
outputting REF_CLK.
Change this so DP83867_CLK_O_SEL_REF_CLK means enable REF_CLK output.
Omitting the property will leave the setting as is (which was the previous
behavior in this case).
Out of range values were silently converted into DP83867_CLK_O_SEL_REF_CLK.
Change this so they generate an error.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The driver ti.c is actually driver for TI DP83867x PHYs, so rename it
accordingly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fix 'mask' calculation in phy_connect() for phy addr '0'.
'mask' is getting set to '0xffffffff' for phy addr '0'
in phy_connect() whereas expected value is '0'.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reported-by: tetsu-aoki via github
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
