Split the common code from the non-DM code, so it can be reused by
the DM code later. As always, the recv() function had to be split
into the actual receiving part and free_pkt part to fit with the
DM.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The RX/TX DMA descriptor rings are per-device-instance private data,
so move them into the private data.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Instead of doing ethernet device lookup by name every time there
is an MDIO access, pass the driver private data via mdiobus priv
to the MDIO bus accessors.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This patch replaces the various uses of struct eth_device for accessing
device private data with struct eepro100_priv, which is compatible both
with DM and non-DM operation.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is a trick in preparation for adding DM support. By passing in
the PCI BDF into the bus_to_phys()/phys_to_bus() macros and calling
that dev, we can substitute dev with udevice when DM support lands
and do minor adjustment to the macros to support both DM and non-DM
operation. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Drop the inline keyword from the static functions, the compiler has a
much better overview and can decide how to inline those functions much
better.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Those macros depended on specific variable names to be declared
at their usage sites, fix this by adding an argument to those
macros and also protect the argument with braces.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Pull the MII registration code into a separate function. Moreover,
properly free memory in case any of the registration or allocation
functions fail, so this fixes an existing memleak.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Use this macro to fully fill the PCI device ID table. This is mandatory
for the DM PCI support, which checks all the fields.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Move the functions around in the driver to prepare it for DM conversion.
Drop forward declarations which are not necessary anymore. No functional
change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Remove all the remaining use of the 'volatile' keyword, as this is
no longer required. All the accesses which might have needed this
use of 'volatile' have been repaired properly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Add cache invalidation and flushes wherever the DMA descriptors are
written or read, otherwise this driver cannot work reliably on any
systems where caches are enabled.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This code is replicated in the driver thrice almost verbatim, factor
it out into a separate function and clean it up. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The current eepro100 driver accesses its memory mapped registers directly
instead of using the standard I/O accessors. This can cause problems on
some systems as the accesses can get out of order. So convert the direct
volatile dereferences to use the normal in/out macros.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is automated cleanup via checkpatch, no functional change.
./scripts/checkpatch.pl --show-types -f drivers/net/eepro100.c
./scripts/checkpatch.pl --types INDENTED_LABEL -f --fix --fix-inplace drivers/net/eepro100.c
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is automated cleanup via checkpatch, no functional change.
./scripts/checkpatch.pl --show-types -f drivers/net/eepro100.c
./scripts/checkpatch.pl -f --fix --fix-inplace drivers/net/eepro100.c
This fixes all the remaining errors except a couple of comments which
are longer than 80 characters, all the volatile misuse and all the
camelcase, that needs a separate patch.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is automated cleanup via checkpatch, no functional change.
./scripts/checkpatch.pl --show-types -f drivers/net/eepro100.c
./scripts/checkpatch.pl --types INDENTED_LABEL -f --fix --fix-inplace drivers/net/eepro100.c
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is automated cleanup via checkpatch, no functional change.
./scripts/checkpatch.pl --show-types -f drivers/net/eepro100.c
./scripts/checkpatch.pl --types POINTER_LOCATION -f --fix --fix-inplace drivers/net/eepro100.c
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is automated cleanup via checkpatch, no functional change.
./scripts/checkpatch.pl --show-types -f drivers/net/eepro100.c
./scripts/checkpatch.pl --types PARENTHESIS_ALIGNMENT -f --fix --fix-inplace drivers/net/eepro100.c
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is automated cleanup via checkpatch, no functional change.
./scripts/checkpatch.pl --show-types -f drivers/net/eepro100.c
./scripts/checkpatch.pl --types BRACES -f --fix --fix-inplace drivers/net/eepro100.c
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This is automated cleanup via checkpatch, no functional change.
./scripts/checkpatch.pl --show-types -f drivers/net/eepro100.c
./scripts/checkpatch.pl --types SPACING -f --fix --fix-inplace drivers/net/eepro100.c
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This code is never enabled, last board that used it was ELPPC which
was removed some 5 years ago, so just remove this code altogether.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
We generate a number of helper inline functions to make accesses easier.
However not all permutations of each function will be used and clang
will warn about unused ones. Decorate all of them with __maybe_unused
because of this.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Do not re-read the HW address from the EEPROM on every start of
transfer, otherwise the user will not be able to adjust ethaddr
as needed. Read the address only once, when the card is detected.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Use this macro to fully fill the PCI device ID table. This is mandatory
for the DM PCI support, which checks all the fields.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Split the driver into common and non-DM functionality, so that the
DM support can later re-use the common code, while we retain the
non-DM code until all the platforms are converted.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Instead of always calling rtl8139_eeprom_delay() with priv->ioaddr,
call it with priv and let the function access priv->ioaddr. This
reduces code duplication and has no impact, since the compiler will
inline this as needed anyway.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Introduce rtl8139_pdata, which is a super-structure around eth_device
and tracks per-device state, here the device IO address, PCI BDF, RX
and TX ring position. Pass this structure around instead of the old
non-DM eth_device in preparation for DM conversion.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
These macros depended on the dev variable being declared wherever
they were used. This is wrong and will not work with DM anyway, so
pass only the PCI BFD into these macros, which fixes the dependency
and prepares them for DM support as well.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Replace the use of custom static ioaddr variable with common dev->iobase,
no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Replace malloc()+memset() combination with calloc(), no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Pull the device name setting into a separate function, as this
will be shared between DM/non-DM variants.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Add the DP8382X generic PHY registration to the TI PHY init file.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
ti_phy_init function was allocated to the DP83867 PHY. This function
name is to generic for a specific PHY. The function can be moved to a
TI specific file that can register all TI PHYs that are defined in the
defconfig. The ti_phy_init file will contain all TI PHYs initialization
so that only phy_ti_init can be called from the framework.
In addition to the above the config flag for the DP83867 needs to be changed
in the Kconfig and dependent defconfig files. The config flag that was
used for the DP83867 was also generic in nature so a more specific
config flag for the DP83867 was created.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
There are devices accesible through mdio clause-45, such as
retimers, that do not have PMA or PCS blocks.
This patch adds MDIO_MMD_VEND1 on the list of device addresses
where phyid is searched. Previous order of devices was kept.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
This is a WAR for DHCP failure after rebooting from the L4T kernel. The
r8169.c kernel driver is setting bit 19 of the rt816x HW register 0xF0,
which goes by FuncEvent and MISC in various driver source/datasheets.
That bit is called RxDv_Gated_En in the r8169.c kernel driver. Clear it
here at the end of probe to ensure that U-Boot can get an IP assigned
via DHCP.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Linux commit 232ba3a51cc2 ('net: phy: Micrel KSZ8061: link failure after
cable connect') implements a fix for the above errata.
This patch replicates that errata fix in an ksz8061 specific init routine.
Signed-off-by: Bryan O'Donoghue <bod@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When an eTSEC is configured to use TBI, configuration of the
TBI is done through the MIIM registers for that eTSEC.
For example, if a TBI interface is required on eTSEC2, then
the MIIM registers starting at offset 0x2_5520 are used to
configure it.
Fixes: 9a1d6af55e ("net: tsec: Add driver model ethernet support")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The current code accesses eTSEC registers using physical
address directly, it's not correct, though no problem on
current platforms. It won't work on platforms, which does
not support 1:1 virtual-physical address map.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Allow the MDIO devices to be probed based on the device tree.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The H6 EMAC is very similar to the H3 variant, except that it uses the
same pinmux as R40. Add support for it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
While the R40 uses a different register for EMAC clock configuration
than other chips, the register has a very similar layout. Reuse the
existing bitfield definitions in this file, since they match.
This allows the driver to compile on the H6 platform, where the
CCM_GMAC_CTRL definitions are not present.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Convert CONFIG_KS8851_MLL and CONFIG_KS8851_MLL_BASEADDR to Kconfig
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Add support for U-Boot DM and DT probing.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Instead of reading out the entire FIFO and possibly overwriting U-Boot
memory, read out one packet per recv call, pass it to U-Boot network
stack, and repeat. It is however necessary to cache RXFC value, because
reading that one out clears it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Split network handling functions into non-DM specific parts and
common code in preparation for conversion to DM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Introduce a private data structure for this driver with embedded
struct eth_device and pass it around. This prepares the driver to
work with both DM and non-DM systems.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Fix various checkpatch complaints.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
There is only one chip ID in the table of chip IDs for this chip.
Read out the chip ID instead and mask off the last "revision" bit
to check the chip ID, this works for all chips in the family. Then
drop the chip ID passing around.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The packet status and length information should be extracted from the
FIFO per-packet. Adjust the code such that it reads the packet meta
data and then the packet afterward, if applicable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Most of the entries in the structure are useless, remove them. Inline
the rest of uses where applicable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Per KS8851-16MLL, the RXQCR is a 16bit register. Use 16bit accessors
to it consistently and drop the ks_wrreg8() function altogether, as
it is not used anymore.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The cached RXQCR value is never updated, remove the cache and just use
the bits in the cache directly in the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Replace combination of malloc()+memset() with calloc() as the behavior
is exactly the same and the amount of code is reduced. Moreover, remove
printf() in the fail path, as it is useless, and return proper -ENOMEM
return code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
- Add DM_ETH support for lx2160aqds, ls2080aqds, ls1088aqds
- QSI related fixes on ls1012a, ls2080a, ls1046a, ls1088a, ls1043a based
platforms
- Bug-fixes/updtaes related to ls1046afrwy, fsl-mc, msi-map property
The DPC fixup for MAC address and enet_if is not made if
/board/ports node is missing in DPC file.
Add /board/ports or /ports nodes if them are missing.
Signed-off-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
Reviewed-by: Ioana Ciornei <Ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Similarly to iommu-map, the msi-map property must also be fixed up
in the device tree, in order for the icid -> streamid translation
be possible in the MSI case as well.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Diana Craciun <diana.craciun@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Bus callback functions for read/write/reset need to be set only for
DM_ETH, moving endif a bit lower.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
This requires quite a few header-file additions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Have this symbol follow the pattern of all other such symbols.
This patch also removes a TODO from the code.
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Have this symbol follow the pattern of all other such symbols.
This patch removes a TODO from the code.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
As per Linux's driver, ID_MODE_DIS is only set when the PHY interface is
RGMII. Don't enable it for the rest of setups.
This has been seen to misconfigure RPi4's PHY when booting Linux.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Implement the read_rom_hwaddr callback to load MAC address from fuse
for imx8m platforms.
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
imx_get_mac_from_fuse is used to load MAC address from fuse. On imx8mp,
we have two different ENET controllers and both need to call this
function. So decouple its declare from fec driver.
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Implement the callbacks to get phy mode interface and txclk
rate configuration.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add dwc eqos for imx support.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add RX delay enable support for RTL8211F PHY.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
For dual ethernet controllers, the HW design may connect ETH phys to
one MDIO ports. So two different ethernet drivers have to share MDIO bus.
Since two ethernet drivers are independent, we can't ensure their probe
order.
To resolve this problem, introduce an eth phy generic driver and uclass.
After eth-uclass binds, we search the mdio node and binds the phy node
with the eth-phy-generic driver.
When one eth driver get its phy device, the parent of phy device will
probe prior than phy device. So this ensure the eth driver ownes the
MDIO bus will be probed before using its MDIO.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add fuse check for fec. If the fuse indicates the module
will not work in the SoC, let's fail the initialization.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In RGMII mode the 10Mbps link speed is supported only when CPSW2G MAC SL is
configured for External Control ("in band") mode
CPSW_PN_MAC_CONTROL_REG.CTL_EN(18) = 1
Hence update am65_cpsw_update_link() to follow documentation.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
The two functions are now exactly the same, remove one of them.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
We can configure the clock output in the device tree. Disable the
hardcoded one in here. This is highly board-specific and should have
never been enabled in the PHY driver.
If bisecting shows that this commit breaks your board it probably
depends on the clock output of your Atheros AR8035 PHY. Please have a
look at doc/device-tree-bindings/net/phy/atheros.txt. You need to set
"clk-out-frequency = <125000000>" because that value was the hardcoded
value until this commit.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add support for configuring the CLK_25M pin as well as the RGMII I/O
voltage by the device tree.
By default the AT803x PHYs outputs the 25MHz clock of the XTAL input.
But this output can also be changed by software to other frequencies.
This commit introduces a generic way to configure this output.
Also the PHY supports different RGMII I/O voltages: 1.5V, 1.8V and 2.5V.
An internal LDO is able to provide 1.5V (default) and 1.8V. The 2.5V
option needs an external supply voltage. This commit adds support to
switch the internal LDO to 1.8V.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Provide functions to read and write the Atheros debug registers.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Debug register 5 contains TX_CLK DELAY at bit 8 and reserved values at
the other bit positions, just like the other PHYs in the family do.
Therefore, it is not necessary to hardcode the reserved values, but
instead simply follow the read-modify-write procedure from the common
function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
To eliminate any doubts about the out-of-reset value of the PHY, that
the driver previously relied on.
If bisecting shows that this commit breaks your board you probably have
a wrong PHY interface mode. You probably want the
PHY_INTERFACE_MODE_RGMII_RXID or PHY_INTERFACE_MODE_RGMII_ID mode.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Also take the opportunity to use the phy_read_mmd and phy_write_mmd
convenience functions.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Delete the extraneous write to debug reg 5 that enables Tx delay
When the driver was originally introduced in commit "6027384a phylib:
Add Atheros AR8035 GETH PHY support", the Tx delay was being
unconditionally enabled.
Then during "2ec4d10b phy: atheros: add support for RGMII_ID, RGMII_TXID
and RGMII_RXID", the author did not notice that code for enabling Tx
delay code was already. Therefore, the if condition for Tx delay has
always been useless for this PHY since this commit introduced it.
Prior to this patch, every AR8035 PHY in U-boot had Tx delay enabled.
After this patch, only those who define the interface as RGMII_TXID or
RGMII_ID will. This is to be expected, but will nonetheless break the
setups of those who didn't know they rely on Tx delay implicitly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Commit 69529c9120 ("net: pcnet: Switch to PCI memory access")
switched from PCI IO access to PCI memory access without updating
the I/O primitives. Contrary to SH, the primitives for memory
access and IO access are implemented differently. Thus doing
memory access with IO port primitives breaks the driver on
MIPS Malta board.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add support for U-Boot DM and DT probing. Furthermore, build the
SMC911x standalone EEPROM example only for the non-DM case, as it
is not converted yet.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch enables the possibility to set FEC_ENET_ENABLE_TXC_DELAY or
FEC_ENET_ENABLE_RXC_DELAY so one can via a define enable the RXC or TXC
delay in the MAC.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Split network handling functions into non-DM specific parts and
common code in preparation for conversion to DM.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Invert the status handling logic in smc911x_recv(), to make the
function easier to read, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Introduce a private data structure for this driver with embedded
struct eth_device and pass it around. This prepares the driver to
work with both DM and non-DM systems.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Convert the IO accessors to standard ones instead of using volatile
void pointers, as those do not cover all the bus access details.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
These accessors are not overridden by any board, and even if they were,
this is something which should be handled via DM now, so remove the
weak alias option. Moreover, drop the inline keyword, as the compiler
can decide better.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Inline all the functions from the header file, as they are not used
outside of the driver or the standalone EEPROM example.
Note that this does introduce considerable amount of duplication in
the standalone EEPROM example, however that one has to be rewritten
anyway, roughly such that the SMC911x driver would expose DM EEPROM
interface and the standalone example would use that.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Pull the MII interface registration into separate function to avoid the
ifdeffery in smc911x_initialize(). Moreover, adjust the fail path such
that we use goto labels.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Fix memleak in the init fail path, where if allocation or registration
of MDIO bus fails, then ethernet interface is not unregistered and the
private data are not freed, yet the probe function reports a failure.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Invert the logic in the aforementioned functions to reduce indent,
no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Rename the function to keep the naming scheme consistent,
no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Replace combination of malloc()+memset() with calloc() as the behavior
is exactly the same and the amount of code is reduced.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
These functions are never used and are likely a pre-DM remnant
from times long past, just remove them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
The rtl8139 driver is derived from Etherboot driver, which is in
turn derived from Linux 8139too driver added in Linux 2.2.18pre14.
An undocumented change in Linux 2.4.10.2 added a new field to the
driver, MODULE_LICENSE("GPL"); . According to current Linux kernel
licensing rules, Documentation/process/license-rules.rst, quote:
"GPL" Module is licensed under GPL version 2. This
does not express any distinction between
GPL-2.0-only or GPL-2.0-or-later. The exact
license information can only be determined
via the license information in the
corresponding source files.
And since the code does not contain any "future" clause, the tag
is therefore GPL-2.0 only.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Just move functions around in preparation for easy DM conversion,
rename rtl_bcast_addr() to rtl8139_bcast_addr(), no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Finish the checkpatch cleanup of the driver, fix the remaining issues
in probe and init function and in global variables, rename the probe
function to rtl8139_init(), no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
This hardware reset and reset-wait implementation was twice in the
driver, factor it out into a separate function. This really should
use wait_for_bit() eventually and return -ETIMEDOUT, but thus far,
handling of any of this is missing from the driver. This must be
added later. Thus far, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_stop(), clean up checkpatch errors in
the stop polling function. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_recv(), clean up various checkpatch errors,
line-over-80 conditions, and malformed comments. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_send(), clean up the TX polling, the TX
OK condition at the end, overuse of typecasts, and various line-over-80
problems. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_reset(), clean up the reset polling
and various line-over-80 problems. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_set_rx_mode(), use unsigned variables
where applicable and inline mc_filter[] values. No functional chanage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
This string of macros is exactly the same thing as rtl8139_rx_config,
so just use rtl8139_rx_config. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_read_eeprom() to keep the naming
consistent, keep the variables sorted in reverse xmas tree. No
functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The macro assumes ee_addr variable to be present when it's being
used. Rework the macro into a function instead and pass it an
argument specifying the register base address, to make it future
proof for DM conversion.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the horrible register definitions in the RTL8139 driver.
This does create a couple of checkpatch errors, but the driver is
full of them anyway, and those will be cleaned up later.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The DMA may attempt to write a DMA descriptor in the ring while it is
being updated. By writing the DMA descriptor buffer address to 0, it
is assured the DMA will not use such a buffer and the buffer can be
updated without any interference.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
This patch prevents an issue where the RX packet might have been
accessed by the CPU, which now has cached data from the packet in
the caches and possibly various write buffers, and these data may
be evicted from the caches into the DRAM while the buffer is also
written by the DMA.
By invalidating the buffer after the CPU accessed it and before the
DMA populates the buffer, it is assured that the buffer will not be
corrupted.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
The current code polls the RX desciptor ring for new packets by reading
the RX descriptor status. This works by accident, as the RX descriptors
are often in non-cacheable memory. However, the driver does support use
of RX descriptors in cacheable memory.
This patch adds a missing RX descriptor invalidation, which assures the
CPU will read a fresh copy of the RX descriptor instead of a cached one.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Currently the code only flushes the first RX descriptor, not every entry
in the RX descriptor ring. Fix this, to make sure the DMA engine can pick
the RX descriptors correctly.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
This code programs the next descriptor in the TX descriptor ring into
the hardware as the last valid TX descriptor. The problem is that if
the currenty descriptor is the last one in the array, the code will
not wrap around correctly and use TX descriptor 0 again, but instead
will use TX descriptor at address right past the TX descriptor ring,
which is the first descriptor in the RX ring.
Fix this by adding the necessary wrap-around.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
The RX descriptor field 3 should contain only OWN and BUF1V bits before
being used for receiving data by the DMA engine. However, right now, if
the descriptor was already used for receiving data and is being cleared,
the field 3 is only modified and the aforementioned two bits are ORRed
into the field. This could lead to a residual dirty bits being left in
the field 3 from previous transfer, and it generally does. Fully set the
field 3 instead to clear those residual dirty bits.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Replace the adhoc debugging ifdeffery with debug_cond() and an
internal SROM_DEBUG macro to select the debug level.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Move the functions in the driver around to better fit future DM
conversion, drop function forward declarations. No functional
change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename these functions to dc2114x_{inl,outl}(), use u32 values in
them instead of plain signed integers as all those values are in
fact register values and the driver code does bitwise operations
on them. No functional change intended.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Replace these macros with static functions to permit the compiler to
do type checking on the functions. The INL()/OUTL() functions have to
be moved in this patch as well, as those DE4X5 macros are using them.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the remaining driver code, macro space alignment, function
declaration indent, replace __attribute__((aligned(32))) with plain
__aligned(32). No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the SROM accessors to bring them up to standards with
U-Boot coding style. Sort variable into reverse xmas tree. No
functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the send_setup_frame() to bring it up to standards with
U-Boot coding style, invert the loops where applicable to cut
down the level of indent. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the driver halt code to bring it up to standards with
U-Boot coding style. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the driver recv code to bring it up to standards with
U-Boot coding style. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the driver send code to bring it up to standards with
U-Boot coding style, invert the loops where applicable to cut
down the level of indent. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the driver init code to bring it up to standards with
U-Boot coding style, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Replace the PCI IO access with PCI memory access, the card
supports both, but the former does not work with QEMU SH4.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Replace mips-specific UNCACHED_SDRAM() macro with standard
map_physmem(), which permits the driver to work on other
systems than mips.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
These macros are not used by any board, remove them to simplify
the driver. The EEPROM accessors are still retained however, as
those might still be useful.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
These macros guard one switch-case statement, which grows mips malta
by some 20 bytes if debug is enabled, and even less if it is not. To
make the code simpler, just support all the NICs and be done with it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Probe the FMan MACs based on the device tree while
retaining the legacy code/functionality.
One notable change introduced here is that, for DM_ETH,
the name of the interfaces is corrected to the fmX-macY
format, that avoids the referral to the MAC block names
which were incorrect for FMan v3 devices (i.e. DTSEC,
TGEC) and had weird formatting (i.e. FM1@DTSEC6, FM1@TGEC1).
The legacy code is left unchanged in this respect.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Allow the MDIO devices to be probed based on the device tree.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move the receive buffer free code in a separate function.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Make any adjustments necessary in order to support DPAA2 devices probed
using CONFIG_DM_ETH. While at it, fixup some styling issues aroung the
switch-case statement.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When CONFIG_DM_ETH is enabled DPAA2 network interfaces will now probe
based on DTS nodes with the "fsl,qoriq-mc-dpmac" compatible.
In this case, transform the ldpaa_eth driver into a UCLASS_ETH driver
and reuse the _open()/_tx()/_stop() functions already inplemented.
For the moment, the ldpaa_eth driver will support both configurations:
with or without CONFIG_DM_ETH enabled. Any 'struct eth_device' occurrence
now has a matching 'struct udevice' made mutually exclusive based on the
state of CONFIG_DM_ETH.
Signed-off-by: Florin Laurentiu Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add a driver for the MDIO interface integrated in the mEMAC (Multi-rate
Ethernet Media Access Controller) and the Fman 10G Ethernet MACs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
mt7531 is a 7-ports switch with 5 embedded giga phys, and uses the same
MAC design of mt7530. The cpu port6 supports SGMII only. The cpu port5
supports RGMII or SGMII in different model.
mt7531 is connected to mt7622 via both RGMII and SGMII interfaces.
In this patch, mt7531 cpu port5 or port6 is configured to maximum
capability to align CPU MAC setting.
The dts has been committed in the commit 6efa450565 ("arm: dts:
mediatek: add ethernet and sgmii dts node for mt7622")
Signed-off-by: Landen Chao <landen.chao@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
If CONFIG_CMD_NAND is disabled, get_nand_dev_by_index() is not
accessible.
This fix allows the build to succeed in this case.
Signed-off-by: Francois Gervais <fgervais@distech-controls.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add management of property "reg" to configure @ of phy and
also "max-speed" property to specify maximum speed in Mbit/s
supported by the device
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add management of property "reset-gpios" in the node identified by
"phy-handle" to configure any GPIO used to reset the PHY.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Reviewed-by: Patrice CHOTARD <patrice.chotard@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Not all IPs have private MDIO bus and MDIO bus should be shared between
several IPs. In past one patch tried to implement it
(https://lists.denx.de/pipermail/u-boot/2018-February/319285.html)
in pretty raw way but it is not the cleanest solution.
This patch is just taking the part of that solution to be able to handle it
over releases without conflicts.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add cache flush to zynq_gem_free_pkt. This is necessary
because some net routines would modify this buffer in place.
The cache_invalidate in the zynq_gem_recv function would cause
the modifications to the buffer to overwrite the DMA from the GEM,
if cache coherency is not enabled in the GEM, the next time the
buffer is in use.
Flushing the cache when the buffer is no longer in use by the
net functions ensures that the GEM DMA is going to take place
into a clean buffer.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
To access the PHY, the MAC registers must be initialized. Call the init
function in probe() to make it so, otherwise the PHY ID readout returns
all zeroes.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
When MACB_ZYNQ is enabled there is compilation warnings
drivers/net/macb.c: In function ‘_macb_init’:
drivers/net/macb.h:675:33: error: ‘MACB_DMACFG’ undeclared (first use in this function);
did you mean ‘MACB_MCF’?
writel((value), (port)->regs + MACB_##reg)
^~~~~
It has been caused by changing macros name by commit below.
Fixes: 6c636514d4 ("net: macb: sync header definitions as taken from Linux")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The correct setting for the RGMII ports on LS1046ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID. There is a pull-up that turns
on Rx internal delay by default and the u-boot does not
override that (yet) so in u-boot the interface is functional.
In Linux the PHY driver is clearing the Rx delay for the
"rgmii-txid" mode and the reception does not work.
Changing the RGMII mode to internal delay here ensures that
device tree fix-ups for the PHY connection type turn on both
Tx and Rx internal delay in Linux.
Fixes: cc1aa218f5 ("armv8/ls1046a: RGMII PHY requires internal
delay on Tx")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The correct setting for the RGMII ports on LS1043ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID. There is a pull-up that turns
on Rx internal delay by default and the u-boot does not
override that (yet) so in u-boot the interface is functional.
In Linux the PHY driver is clearing the Rx delay for the
"rgmii-txid" mode and the reception does not work.
Changing the RGMII mode to internal delay here ensures that
device tree fix-ups for the PHY connection type turn on both
Tx and Rx internal delay in Linux.
Fixes: 5a78a472f6 ("armv8/ls1043a: RGMII PHY requires internal
delay on Tx")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The RGMII modes that include internal delay were not all
properly treated in the memac code. Add support for all
RGMII delay modes.
Fixes: 111fd19e3b ("fm/mEMAC: add mEMAC frame work")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The PHY models of the Marvell 88E151x series are not reliably
distinguishable by their uid / PHY identifiers.
The 88E1510, 88E1512, 88E1514 and 88E1518 all have the same OUI and
model number and bits 3:0 in the PHY Identifier 2 (Page 0, Reg 3) are
described as HW revision number, but both 88E1510 and 88E1518 PHYs were
observed with the same HW rev number (1).
Before commit 83cfbeb0df ("net: phy: Fix mask so that we can identify
Marvell 88E1518"), the 88E151x were detected because the HW revision
bits were masked from the uid. After that change, 88E1510/12/18 were all
detected as 88E1518 and the 88E1510 specific code was no longer run.
I modified the mask to again ignore all four HW revision bits, removed
the 88E1510 specific code (board-specific LED/INTn setup), which was not
called since late 2016 anyway and renamed the config function and
phy_driver struct to the better fitting 88e151x.
The uid and mask bits 3:0 are now again the same as in the Linux kernel.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
This patch adds ability to switch beetween two PHY SGMII modes.
Some hardware, for example, FPGA IP designs may use 6-wire mode
which enables differential SGMII clock to MAC.
Patch description, dt flags have been done in mainline Linux by
commit a2111c460c0c ("net: phy: dp83867: Add documentation for SGMII mode type")
and by commit 507ddd5c0d47 ("net: phy: dp83867: Add SGMII mode type switching")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Commit 27c3f70f3b ("net: phy: Increase link up delay in
genphy_update_link()") increased the per-iteration waiting time from
1ms to 50ms, without adjusting the timeout counter. This lead to the
timeout increasing from the typical 4 seconds to over three minutes.
Adjust the timeout counter evaluation by that factor of 50 to bring the
timeout back to the intended value.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Fixes: net: phy: Increase link up delay in genphy_update_link() ("27c3f70f3b50")
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Matthias Brugger <mbrugger@suse.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The driver now unconditionally prints some information that's not
universally useful. Replace printf with debug.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use either USXGMII or XFI in aquantia_set_proto and drop XGMII as a valid
protocol configuration. The PHY doesn't support it, it's just used as an
alias for one of the other two protocols.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add NC-SI to the usual phy handling. This makes two notable changes:
- Somewhat similar to a fixed phy, phy_connect() will create an NC-SI
phy if CONFIG_PHY_NCSI is defined.
- An early return is added to phy_read() and phy_write() to handle a
case like the NC-SI phy which does not define a bus.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This introduces support for the NC-SI protocol, modelled as a phy driver
for other ethernet drivers to consume.
NC-SI (Network Controller Sideband Interface) is a protocol to manage a
sideband connection to a proper network interface, for example a BMC
(Baseboard Management Controller) sharing the NIC of the host system.
Probing and configuration occurs by communicating with the "remote" NIC
via NC-SI control frames (Ethernet header 0x88f8).
This implementation is roughly based on the upstream Linux
implementation[0], with a reduced feature set and an emphasis on getting
a link up as fast as possible rather than probing the full possible
topology of the bus.
The current phy model relies on the network being "up", sending NC-SI
command frames via net_send_packet() and receiving them from the
net_loop() loop (added in a following patch).
The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent
field definitions.
[0]: https://github.com/torvalds/linux/tree/master/net/ncsi
[1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Driver probe function is called again and again in case of error.
Malloc space is getting full which is is reported by:
Insufficient RAM for page table: 0x15000 > 0x14000.
Please increase the size in get_page_table_size()
### ERROR ### Please RESET the board ###
The patch is freeing allocated buffers on error path to avoid panic.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
On Xilinx ZynqMP revA board initial value of PHYCR register is 0x5448 which
means FORCE_LINK_GOOD is already setup. Origin code was doing write but the
new code is doing read/modify/write and keep this bit untouched. That's why
ethernet stop to work.
The patch is cleaning this bit when PHYCR value is composed.
Tested on Xilinx zcu102-revA and zcu104-rev1.0 boards.
Fixes: 37d6265f2b ("net: phy: dp83867: refactor rgmii configuration")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
flush_dcache_range() expects unsigned long in the arguments. Here u32
variable is unable to hold the higher address value when ddr mapped
to higher addresses & flushing lower address dchache range instead
which is unmapped causing to crash.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The implementation of dma_map_single() and dma_unmap_single() is
exactly the same for all the architectures that support them.
Factor them out to <linux/dma-mapping.h>, and make all drivers to
include <linux/dma-mapping.h> instead of <asm/dma-mapping.h>.
If we need to differentiate them for some architectures, we can
move the generic definitions to <asm-generic/dma-mapping.h>.
Add some comments to the helpers. The concept is quite similar to
the DMA-API of Linux kernel. Drivers are agnostic about what is
going on behind the scene. Just call dma_map_single() before the
DMA, and dma_unmap_single() after it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl48iogACgkQfxc6PpAI
reaVzAf/an3/yKe6r3CVWlcRV6H/dVg1ApnnLpX7jS0p0b++oCVvOiy7z1WPXj3k
b1SSgENDeeZ/8EHio+Gf7ZidH/TGEj7L6YEFwd1t60GMkZiWEkNf4Z53tw482YG+
96hoPD+ySTW+ddIdVHWAFG2I4aEiKHANJAp/ItNdD+rLbrEwNQy+eiK5JTOk80B6
/X8AJCLZeAC1s7vs+2+WolgjT78QGzA9HHalMiublcqh0ivKKk0QeQiOKKPe8JYJ
om5YY1TxayQ60Xmo5f39/SBfzEEklxw83sU9o1tBeYzyVUpu7fQdkxiDbWdsij77
DgwLdeYQJGbN+hdSWE0gjTqyhW+lWA==
=KRoA
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-6feb20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
sandbox conversion to SDL2
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
building mtk ethernet driver for aarch64 (mt7622) results
in warnings/errors
"error: cast from pointer to integer of different size"
Fixes: 23f17164d9 ("ethernet: MediaTek: add ethernet driver for MediaTek ARM-based SoCs")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
This patch add sgmii init part for the mediatek SoC that
support sgmii mode. It is a must for mt7622.
Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
- add dfu support to dwc2 for bcm2835
- enable DFU for RPi4
- Fix RPi4 memory map to include the genet device
- add driver for the genet ethernet device
- enable network support in RPi4 config
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEEUdvKHhzqrUYPB/u8L21+TfbCqH4FAl43/6QSHG1icnVnZ2Vy
QHN1c2UuY29tAAoJEC9tfk32wqh+Fq0P/1vCbkiRgOtOIMPh/b7qWUVweTdgwcbf
9v8Qa2IKc0FYgjYjIMjihfbvF7R0vGaOUX13yKDV/3v42cpLkOxBauCYasiXznI+
9hBwKfOFPzLpSz3SJ+LRn0XhHSAZ1jcT19pgaPmA5Pry6l7JEai4M3JFeYeJRWOt
N1EFqxqqeAQ+eXdQWXTKh6AiFEia7aL4OVcU5HY9BMyDW8H13gvNejoeSXNKLupM
GGHJfG/TRKHP5UJoqH+I9XFdkUKfN4e1oWpxl7nA5HpvRfFgO+AQm9OgM2xumnGp
+4kS4T5FexCrcQ37m5fG9+LSxk2PB8+P0kmfImaO54lUdAtjB+iqg4RUB7eN/vLH
37S13AB7T8OTjbe8tlLCjGDXQ/8xU+NDZQsE9GnRmaj2UbK57hJPW6kTRgwK4BEZ
l0Rr9RrHlhrBvywHMII11fhH+wVO0R29GFvRZSSscRqvKq61FF//r8hNQX7xtErf
+OIEgIcEt9bbLyq7LJQ+2xRdQj4UgSv5/poaaoWX+uY4+yUElbiPpTJLN2oslZ8x
liUKigWmTgF8G1ukalyA1u3xj0kyfl4QCxoJpNqoaHg9sel0S5igGE0dLzKXUKSw
1A7BCT0rO/FhoMxc7P4kHjpIKlw6Tatw1wJY3g8VzRgEsXlTawNszadO1jswBmHV
9XFk+iH6f/rg
=Sv9b
-----END PGP SIGNATURE-----
Merge tag 'rpi-next-2020.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-raspberrypi
- DFU support file operations lager then the default max size
- add dfu support to dwc2 for bcm2835
- enable DFU for RPi4
- Fix RPi4 memory map to include the genet device
- add driver for the genet ethernet device
- enable network support in RPi4 config
The Broadcom GENET Ethernet MACs are used in several MIPS based SoCs
and in the Broadcom 2711/2838 SoC used on the Raspberry Pi 4.
There is no publicly available documentation, so this driver is based
on the Linux driver. Compared to that the queue management is
drastically simplified, also we only support version 5 of the IP and
RGMII connections between MAC and PHY, as used on the RPi4.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
[Andre: heavy cleanup and a few fixes]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Now that arch specific dma mapping APIs take care of cache
flush/invalidate, drop local cache flush operation.
While at that fix dma_unmap_single() call to match new prototype
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Separate MAC and serdes configuration, MAC configuration must be applied
at each enetc_start() as FLR clears it.
This restores traffic for ENETC interfaces in USXGMII mode.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The LS1028A SoC is special in the handling of the MAC addresses. We need
to write to the IERB version of the PSIPMAR0/1 register. This value will
be sampled into the corresponding port PSIPMAR0/1 register if the PCI
memory access is enabled.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Intead of setting the MAC address in enetc_start() use the proper
write_hwaddr(). U-Boot takes care of the random MAC address, too.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Passes on the primary address used by u-boot to Linux. The code does a DT
fix-up for ENETC PFs and sets the primary MAC address in IERB. The address
in IERB is restored on ENETC PCI functions at FLR.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
These three clock functions don't use driver model and should be migrated.
In the meantime, create a new file to hold them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add specific dm code, but maintaining this driver as is, so more in the
shape of a mii library. Can be moved to dm in a further step.
Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
Bring in the following merges:
commit 8fbbec12f7
Merge: 87f69f467a63618e71e8
Author: Tom Rini <trini@konsulko.com>
Date: Fri Jan 3 09:48:47 2020 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq into next
- updates and fixes on ls1028a, lx2, ls1046a, MC-DPSPARSER support
commit 87f69f467a
Merge: c0912f9bbf4466b99703
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 24 08:18:19 2019 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx into next
- Enable DM driver on ppc/km boards
- Enable DM_USB for some of NXP powerpc platforms: P5040, T4240, T208x,
T104x, P4080, P2041, P2020, P1020, P3041
- Some updates in mpc85xx-ddr driver, km boards
commit c0912f9bbf
Merge: 533c9f5714a1d6dc3f84
Author: Tom Rini <trini@konsulko.com>
Date: Wed Dec 18 07:20:19 2019 -0500
Merge branch 'next' of https://gitlab.denx.de/u-boot/custodians/u-boot-x86 into next
- Various x86 common codes updated for TPL/SPL
- I2C designware driver updated for PCI
- ICH SPI driver updated to support Apollo Lake
- Add Intel FSP2 base support
- Intel Apollo Lake platform specific drivers support
- Add a new board Google Chromebook Coral
commit 533c9f5714
Merge: 553cb06887033e18b47b
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 17 07:53:08 2019 -0500
Merge tag '20191217-for-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c into next
i2c: for next
- misc: i2c_eeprom:
Add partition support and add ability to query size
of eeprom device and partitions
- i2c common:
add support for offset overflow in to address and add
sandbox tests for it.
commit 553cb06887
Merge: f39abbbc53b4f98b3b16
Author: Tom Rini <trini@konsulko.com>
Date: Thu Dec 12 08:18:59 2019 -0500
Merge tag 'dm-next-13dec19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm into next
buildman improvements including toolchain environment feature
sandbox unicode support in serial
Add support for DPSPARSER object (create/destroy, open/close, apply spb)
which is required to configure Soft Parser by using MC.
Also add uboot command to apply Soft Parser Blob with command:
fsl_mc apply spb <spb_load_addr>
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Passing 0 to PHY connect used to trigger a MDIO scan due to a bug fixed in
the meantime. It's unclear if bcm-sf2 wants to connect to PHY @ addr 0 or
is scanning the bus, passing -1 here should keep it functional either way.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Cc: Jiandong Zheng <jdzheng@broadcom.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
PHY address 0 is a valid PHY address, to scan for all PHYs, pass -1 to
phy_connect(). Passing 0 used to work before be accident, but does no
longer.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
At present if CONFIG_SPL_GPIO_SUPPORT is enabled then the GPIO uclass
is included in SPL/TPL without any control for boards. Some boards may
want to disable this to reduce code size where GPIOs are not needed in
SPL or TPL.
Add a new Kconfig option to permit this. Default it to 'y' so that
existing boards work correctly.
Change existing uses of CONFIG_DM_GPIO to CONFIG_IS_ENABLED(DM_GPIO) to
preserve the current behaviour. Also update the 74x164 GPIO driver since
it cannot build with SPL.
This allows us to remove the hacks in config_uncmd_spl.h and
Makefile.uncmd_spl (eventually those files should be removed).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Get flow ID information for RX DMA channel using dma_get_cfg() interface
instead of reading from DT. This is required in order to avoid DT update
whenever there is change in the range of flow ID allocated to the host.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Fixes: e766849713 ("net: ftgmac100: convert the RX/TX descriptor arrays")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This bus is used to access internal SoC PHYs. These PHYs are configured
by the ENETC driver directly, but it's useful to have command line access
to this MDIO to debug the system especially when using new external PHYs.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
On some boards MDIO may get stuck if it detects echo on the line. This is
a know hardware issue, there is a board fix for it. In case we're running
on a board that doesn't have the fix, we don't want to loop here forever
and freeze U-Boot.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This reduces the time needed to establish a link as we don't reset the link
each time the interface is used. Our Link capabilities do not change at
run-time so there is no need to re-apply PHY configuration each time.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The original code enabled link speeds up to 1Gbps, but the interface can
go up to 2.5G, enable that speed to in PHY AN mask.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Uses the new dm_eth_phy_connect helper to connect to the PHY to simplify
the code.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In some cases the link on the system interface of the aquantia PHY comes up
after the link on line interface. The link state loop only checks the line
side, which may result in first packet sent being lost.
Use aquantia_link_is_up instead, which checks both system and line side on
gen 2/3 PHYs to avoid losing the 1st packet.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Aquantia PHYs have a SMBus interface mostly used for debug. The addresses
on this interface are normally set up by PHY firmware, but depending on the
board they may end up not being unique. Add an optional DT property used
to change SMBus address if needed.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
MDI pins up to the RJ45 connector may be reversed on the board and the
default PHY configuration applied by firmware may or may not match that.
Add an optional DT property to configure MDI reversal for this case.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If PHY is not ready for data by the time _config is called, reconfigure the
PHY system interface to use the proper protocol based on phydev->interface,
just in case the defaults set by PHY firmware don't match current
configuration.
Signed-off-by: Florin Laurentiu Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Uses the data field in phy_driver structure to identify the PHY generation.
This is useful for custom configuration as non-generic PHY registers are
not 100% compatible between generations.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The PHY supports XFI and USXGMII, the notable difference being that USX AN
is enabled for USXGMII. Legacy code uses XGMII for any 10G proto and
detects whether USX AN should be enabled or not using a PHY status
register. Keep that functionality too, so we don't break existing drivers.
Signed-off-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fix vendor name in MV88E61xx option description.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Support probing and init for 88E6071 switch.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
On mv88E6071 the 'EDet' field offset, width and sense control
bits are different, adjust the driver to init the PHY control
register as needed. This fixes not working link detection and
tftp transfers.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
On 88E6071 chip the port status register bit field offsets
for duplex and link bits differ. Extend the driver to use
88E6071 specific offset values. The width of bit fields for
speed status differ, too. Adapt for proper port speed
detection on 88E6071.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Extend the driver to init switch register offsets from variables
instead of compile time macros and enable detection of 88E6071 and
compatible devices. Ethernet transfer (e.g. tftp) does not work yet,
so enable the registration of the 'indirect mii' bus for easier PHY
register access by 'mii' command.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The KSZ8081 PHY has a factory test mode which is set at the de-assertion
of the reset line based on the RXER (KSZ8081RNA/RND) or TXC
(KSZ8081MNX/RNB) pin. If a pull-down is missing, or if the pin has a
pull-up, the factory test mode should be cleared by manually writing a 0
(according to the datasheet).
Create another ksz8081_config function to handle this case.
Suggested-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Aquantia quad-phys may take longer to initialize. This commit adds
a polling mechanism for a global alarm bit that tells if phy init
sequence is completed.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This allows passing arbitrary addresses through macb_miiphy_read and
macb_miiphy_write, therefore enabling the mii command to access
all mdio bus devices instead of only the defined phy.
Signed-off-by: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
To support accessing arbitrary addresses the mii/mdio bus it is
necessary that the macb_mdio_read and macb_mdio_write functions
do not implicitly use the address of the connected phy.
The function signature is extended according to the Linux kernel
equivalent.
Signed-off-by: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
I've noticed that in most cases when genphy_update_link() is called, the
ethernet driver (mt7628-eth in this case) fails with the first ethernet
packets. Resulting in a timeout of the first tftp command. Increasing
the delay in the link check look from 1 to 50 ms and moving it below the
BMSR register read fixes this issue, resulting in a stable ethernet
traffic, even after initial link autonogotiation.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This version of the RTL-8168 chip can be found on some add-in cards sold
by CSL-Computer GmbH & Co. KG. The chip isn't special in any way, but it
needs to have the ChipCmd register programmed after the DMA descriptors
have been set up, so make sure that happens by adding an entry to the
chip information table.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Changes to mvpp2.c require the MVMDIO module which in turn uses
DM_MDIO.
Signed-off-by: Nevo Hed <nhed+github@starry.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit ports mvpp2 to use the recently introduced Marvell MDIO
(MVMDIO) driver. It removes direct interaction with the SMI & XSMI
busses. This commit is based in part on earlier work by
Ken Ma <make@marvell.com> in Marvell's own downstream repo:
https://github.com/MarvellEmbeddedProcessors/u-boot-marvell/commit/c81dc39.
The above refrenced work was based on an MVMDIO implementation that
never made it into U-Boot. With this patch the mvpp2 driver switches
to use the new MVMDIO driver that is based on a more universal
mdio-uclass implementation.
Signed-off-by: Nevo Hed <nhed+github@starry.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If the phy doesn't match with any existing u-boot drivers, the phy
framework will connect it to the generic one which uid ==
0xffffffff. In this case, act as if the phy wouldn't be declared in
dts. Otherwise, in case of 3310 (for which the driver doesn't exist)
the link is marked as always down. Removing phy entry from dts in case
of 3310 is not a good option because it is required for the
phy_fw_down procedure.
This patch fixes the issue with the link always down on MCBIN board.
nhed: added NULL deref test.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Tested-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Nevo Hed <nhed+github@starry.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Issue:
- Network stuck if autonegotion fails.
Issue root cause:
- When autonegotiation fails during port open procedure, the packet
processor configuration does not finish and open procedure exits
with error.
- However, this doesn't prevent u-boot network framework from
calling send and receive procedures.
- Using transmit and receive functions of misconfigured packet
processor will cause traffic to get stuck.
Fix:
- Continue packet processor configuration even if autonegotiation
fails. Only error message is triggered in this case.
- Exit transmit and receive functions if there is no PHY link
indication.
- U-boot network framework now calls open procedure again during next
transmit initiation.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Tested-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Refactor SGMII configuration to group all settings together and reduce
number of MDIO transactions.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Based on commit 27708eb5481b ("net: phy: dp83867: IO impedance is not
dependent on RGMII delay") of mainline linux kernel.
The driver would only set the IO impedance value when RGMII internal delays
were enabled. There is no reason for this. Move the IO impedance block
out of the RGMII delay block.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Based on commit c11669a2757e ("net: phy: dp83867: Rework delay rgmii delay
handling") of mainline linux kernel.
The current code is assuming the reset default of the delay control
register was to have delay disabled. This is what the datasheet shows as
the register's initial value. However, that's not actually true: the
default is controlled by the PHY's pin strapping.
This patch:
- insures the other direction's delay is disabled If the interface mode is
selected as RX or TX delay only
- validates the delay values and fail if they are not in range
- checks if the board is strapped to have a delay and is configured to use
"rgmii" mode and warning is generated that "rgmii-id" should have been
used.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Based on commit 13c83cf8af0d ("net: phy: dp83867: Add ability to disable
output clock") of mainline linux kernel.
Generally, the output clock pin is only used for testing and only serves as
a source of RF noise after this. It could be used to daisy-chain PHYs, but
this is uncommon. Since the PHY can disable the output, make doing so an
option. I do this by adding another enumeration to the allowed values of
ti,clk-output-sel.
The code was not using the value DP83867_CLK_O_SEL_REF_CLK as one might
expect: to select the REF_CLK as the output. Rather it meant "keep clock
output setting as is", which, depending on PHY strapping, might not be
outputting REF_CLK.
Change this so DP83867_CLK_O_SEL_REF_CLK means enable REF_CLK output.
Omitting the property will leave the setting as is (which was the previous
behavior in this case).
Out of range values were silently converted into DP83867_CLK_O_SEL_REF_CLK.
Change this so they generate an error.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The driver ti.c is actually driver for TI DP83867x PHYs, so rename it
accordingly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fix 'mask' calculation in phy_connect() for phy addr '0'.
'mask' is getting set to '0xffffffff' for phy addr '0'
in phy_connect() whereas expected value is '0'.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reported-by: tetsu-aoki via github
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
- rockchip pwm driver update to support all the SoCs
- RK3308 GMAC and pinctrl support
- More UART interface support on PX30 and pmugrf reg fix
- Fixup on misc for eth_addr/serial#
- Other updates on variant SoCs
Add the glue code to allow the rk3308 variant of the Rockchip gmac
to provide network functionality.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add null pointer check to take care of out of memory errors.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
This converts the following to Kconfig:
CONFIG_SYS_CORTINA_FW_IN_MMC
CONFIG_SYS_CORTINA_FW_IN_NAND
CONFIG_SYS_CORTINA_FW_IN_NOR
CONFIG_SYS_CORTINA_FW_IN_REMOTE
CONFIG_SYS_CORTINA_FW_IN_SPIFLASH
Signed-off-by: Tom Rini <trini@konsulko.com>
Move these functions into the command.h header file which is a better fit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function belongs in time.h so move it over and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Drop inclusion of crc.h in common.h and use the correct header directly
instead.
With this we can drop the conflicting definition in fw_env.h and rely on
the crc.h header, which is already included.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add the glue code to allow the px30 variant of the Rockchip gmac
to provide network functionality.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
-------------------
i.MX8MN SoC support
ROM API image download support
i.MX8MM enet enabling
-----BEGIN PGP SIGNATURE-----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=sgCz
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20191105' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20191105
-------------------
i.MX8MN SoC support
ROM API image download support
i.MX8MM enet enabling
Add the missing RGMII PHY modes in which case the MAC has configure its
RGMII settings. The only difference between these modes is the RX and
TX delay configuration. A user might choose any RGMII mode in the device
tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The saved ofnode is used by some PHY drivers to access the device tree
node of the PHY.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add more clks for fec_mxc according to Linux Kernel 5.4.0-rc1
drivers/net/ethernet/freescale/fec_main.c.
Since i.MX8MQ not support CLK_CCF, so add a check to restrict
the code only effect when CONFIG_IMX8M and CONFIG_CLK_CCF both defined.
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Make FEC driver could be used by i.MX8M when CONFIG_FEC_MXC defined
in defconfig.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Conver TI CPSW driver to use dev/ofnode api.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
[trini: Add <dm/ofnode.h> to provide the prototype to ofnode]
Signed-off-by: Tom Rini <trini@konsulko.com>
Now AM65x CPSW2G driver will disable MAC TX internal delay for PHY
interface mode "rgmii-rxid" which is incorrect. Hence, fix it by keeping
default value (enabled) for MAC TX internal delay when "rgmii-rxid"
interface mode is selected.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Now TI CPSW driver will disable MAC TX internal delay for PHY interface
mode "rgmii-rxid" which is incorrect.
Hence, fix it by keeping default value (enabled) for MAC TX internal delay
when "rgmii-rxid" interface mode is selected.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
This patch adds support for standard Ethernet "max-speed" DT property to
allow PHY link speed limitation.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
According to TRMs the 10Mbps link speed is supported in RGMII only when
CPSW2G MAC SL is configured for External Control ("in band") mode
CPSW_SL_MACCTRL.EXT_EN(18) = 1.
Hence update cpsw_slave_update_link() to follow documentation.
[1] https://patchwork.kernel.org/patch/10285239/
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
This patch add support for mt7628-eth to isolate LAN/WAN ports mainly to
prevent LAN devices from getting IP address from WAN.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
When received a packet with an invalid length recorded in rx descriptor,
we should free this rx descriptor to allow us to continue to receive
following packets.
Without doing so, u-boot will stuck in a dead loop trying to process this
invalid rx descriptor.
This patch adds a call to mt7628_eth_free_pkt() after received an invalid
packet length.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The mt7628 has an embedded ethernet switch (5 phy ports + 1 cpu port).
Although in IOT mode only port0 is usable, the phy0 is still connected
to the switch, not the ethernet gmac directly.
This patch rewrites it and makes it optional. It can be turned on by adding
mediatek,poll-link-phy = <?> explicitly into the eth node. By default the
driver is switch mode with all 5 phy ports working without link detection.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch removes hardcoded gpio settings as they have been replaced by
pinctrl in dts, and also replaces regmap-based phy reset with a more
generic reset controller.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch assings the phynode pointer to the phydev node as it is needed
later in the corresponding phy driver to read phy properties from DT.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for gmiitorgmii converter.
This converter sits between the MAC and the external phy
MAC <==> GMII2RGMII <==> RGMII_PHY.
The ethernet driver probes this bridge and this bridge driver
probes real phy driver and invokes the real phy functionalities
as requested. This bridge just needs to be configured based on
real phy negotiated speed and duplex.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch define init routine for generic phy driver and registers it
using phy_register as this generic phy driver also needs to be relocated
incase of manual reloc.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch removes check for Versal platform
in gem driver as it now supports clock setting
through clock framework.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds new versal compatible string to GEM driver for Versal
platform.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The commit
642b80d256 ("net: designware: drop compatible altr, socfpga-stmmac")
breaks designware ethernet for all ARC boards. It removes
"altr, socfpga-stmmac" compatible from "drivers/net/designware.c"
without changing compatible in the boards which use it.
Fix that by adding "snps,arc-dwmac-3.70a" compatible string to
"drivers/net/designware.c" and using it in ARC boards device tree.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
With commit c6d07bf440 ("net/macb: increase RX buffer size for GEM")
ethernet support does not work any more with d-cache enabled on the
AT91SAM. The reason is, that MACB_RX_BUFFER_SIZE was changed from 4096
to 128 but this change was not refected in the rx_buffer flush and
invalidate functions, as these also use this macro.
This patch now fixes this by calculating the rx buffer size correctly
again in those functions. With this change, ethernet works again
reliably on my AT91SAM board.
Signed-off-by: Stefan Roese <sr@denx.de>
Fixes: c6d07bf440 ("net/macb: increase RX buffer size for GEM")
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Anup Patel <anup.patel@wdc.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The same compatible = "altr,socfpga-stmmac" appears in both
drivers/net/designware.c and drivers/net/dwmac_socfgpa.c,
creating ambiguity in which driver will be bound.
For Intel/Altera SoC devices, dwmac_socfpga.c is the correct driver.
So drop the compatible string from designware.c.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This reverts commit 1b0c9914cc.
Commit 1b0c9914cc ("net: macb: Fixed reading MII_LPA register")
causes 100Mbps does not work any more with SiFive FU540 GEM on the
HiFive Unleashed board. Revert it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
It was missing in the original submission and not having it in place causes
issues with probing of PCI devices.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Align the board and driver prototype for board_interface_eth_init
to avoid execution issue (the interface_type parameter is defined
as int or phy_interface_t).
To have a generic weak function (it should be reused by other driver)
I change the prototype to use directly udevice.
This prototype is added in netdev.h to allow compilation check
and avoid warning when compiling with W=1 on file
board/st/stm32mp1/stm32mp1.c
warning: no previous prototype for 'board_interface_eth_init'\
[-Wmissing-prototypes]
int board_interface_eth_init(int interface_type, ....
^~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch solves many warnings when compiling with W=1:
warning: no previous prototype for '....' [-Wmissing-prototypes]
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Do not use random value from stack as return value of pfe_phy_write().
Indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
SANDBOX_PHY_REG_CNT is not an allowable index for the array
u16 reg[SANDBOX_PHY_REG_CNT].
Identified by cppcheck.
Fixes: b47edf8069 ("test: dm_mdio: add a 2nd register to the emulated PHY")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
mvpp2 already has support for setting MAC addresses but this
functionality was not exposed to the ethernet core. This commit exposes
this functionality so that MAC address assignments stored in U-Boot's
environment are correctly applied before Linux boots.
Signed-off-by: Matt Pelland <mpelland@starry.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds a separate driver for the MDIO interface of the
Marvell Ethernet controllers based on driver model. There are two
reasons to have a separate driver rather than including it inside
the MAC driver itself:
*) The MDIO interface is shared by all Ethernet ports, so a driver
must guarantee non-concurrent accesses to this MDIO interface. The
most logical way is to have a separate driver that handles this
single MDIO interface, used by all Ethernet ports.
*) The MDIO interface is the same between the existing mv643xx_eth
driver and the new mvneta/mvpp2 driver. Even though it is for now
only used by the mvneta/mvpp2 driver, it will in the future be
used by the mv643xx_eth driver as well.
This driver supports SMI IEEE for 802.3 Clause 22 and XSMI for IEEE
802.3 Clause 45.
This patch also adds device tree binding for marvell MDIO driver.
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Create drivers/net/fsl-mc/Kconfig and move fsl-mc specific configs
from arch/arm/cpu/armv8/fsl-layerscape/Kconfig to this new Kconfig
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This driver is used for MDIO muxes driven over I2C. This is currently
used on Freescale LS1028A QDS board, on which the physical MDIO MUX is
controlled by an on-board FPGA which in turn is configured through I2C.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
MC firmware need to be aligned to 512M, so minimum 512MB DDR is reserved.
But MC support to work with 128MB or 256MB DDR memory also, in this
case, rest of the memory is not usable.
So reporting this extra memory to Linux through dtb memory fixup.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
This header file is now only used by files that access internal
environment features. Drop it from various places where it is not needed.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Move env_set_hex() over to the new header file along with env_set_addr()
which uses it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move this function over to the new header file. Also rename it to have an
env_ prefix like the other functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fix various type warnings when building this driver for 64bit machine.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The R8A77980 V3H gether needs a few minor adjustments to the sh_eth
driver, add them to support ethernet on R8A77980.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
commit 49116e6d23 ("doc: arch: Convert README.sandbox to reST")
Moves README.sandbox to doc/arch.
Replace all the existing instances to point to the right documentation
file.
Signed-off-by: Keerthy <j-keerthy@ti.com>
H3/H5 can either use the internal phy or an external one.
Before getting clock and resets for the internal phy,
test that we are using it because otherwise it break emac
when using an external phy.
Tested-on: OrangePi PC2 (H5)
Fixes: 2348453c41 (net: sun8i_emac: Add EPHY CLK and RESET support)
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Now that we removed all legacy boards selecting TI_EMAC we can
completely convert the driver code to using the driver model.
This patch also updates all remaining users of davinci_emac.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Adam Ford <aford173@gmail.com> #am3517-evm & da850-evm
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Instead of depending on CONFIG_SYS_LITTLE_ENDIAN, we check at runtime
whether underlying system is little-endian or big-endian. This way
we are not dependent on any U-Boot specific OR compiler specific macro
to check system endianness.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The SiFive MACB ethernet has a custom TX_CLK_SEL register to select
different TX clock for 1000mbps vs 10/100mbps.
This patch adds SiFive MACB compatible string and extends the MACB
ethernet driver to change TX clock using TX_CLK_SEL register for
SiFive MACB.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In the case of the tsec network driver, so far there has been no
mainline user of DM_ETH where the DT bindings get used.
In the case of the mdio bus, it looks like the "fsl,tsec-mdio" string
was made up for the documentation, but there is no mainline code that
parses the "compatible" property anyway.
In both cases, there are no DT blobs that contain the old strings.
So change the documentation to "fsl,etsec2" for the Ethernet ports and
"fsl,etsec2-mdio" for the MDIO buses, which are strings that Linux also
uses, at least for LS1021A. More compatible strings can be added once
other (PowerPC) SoCs are migrated to DM_ETH.
The current ls1021a.dtsi doesn't match what was documented for the MDIO
buses anyway (the "compatible" is "gianfar" currently). This will be
fixed in the next patch.
Fixes: 69a00875e3 ("doc: dt-bindings: Describe Freescale TSEC ethernet controller")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In tsec_init, the MAC address is retrieved from 2 different structures
depending on whether DM_ETH is enabled or not.
But since the field name is the same inside both structures, we can
conditionally define the structure of the correct type and simplify the
assignments.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This replaces debug() calls with printf() so that it is immediately
obvious from the console that something is wrong.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is a cosmetic patch that reorders variable definitions in the
inverse order of their line length, where possible.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
By convention, the eTSEC MDIO controller nodes are defined in DT at
0x2d24000 and 0x2d50000, but actually U-Boot does not touch the
interrupt portion of the register map (MDIO_IEVENTM, MDIO_IMASKM,
MDIO_EMAPM).
That leaves only the MDIO bus registers (MDIO_MIIMCFG, MDIO_MIIMCOM,
MDIO_MIIMADD, MDIO_MIIMADD, MDIO_MIIMCON, MDIO_MIIMSTAT) which start at
the 0x520 offset.
So shift the DT-defined register map by the offset of MDIO_MIIMCFG when
mapping the MDIO bus registers.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The point of this patch is to eliminate the use of the locally-defined
"reg" variable (which interferes with next patch) and simplify the
fallback to the default CONFIG_SYS_TBIPA_VALUE in case "tbi-handle" is
missing.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Macb Ethernet controller requires a RX buffer of 128 bytes. It is
highly sub-optimal for Gigabit-capable GEM that is able to use
a bigger DMA buffer. Change this constant and associated macros
with data stored in the private structure.
RX DMA buffer size has to be multiple of 64 bytes as indicated in
DMA Configuration Register specification.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
DMA configuration was heavily dependent on the HW
defaults, add function to properly set the required
fields, including the new dma_burst_length.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Anup Patel <anup.patel@wdc.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
GEM support higher DMA burst writes/reads than the default (4).
add configuration structure with dma burst length so it could be
applied later to DMA configuration.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Anup Patel <anup.patel@wdc.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds support for the sgmii phy interface,
available only to DM users, dictated by current driver
design.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Anup Patel <anup.patel@wdc.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
macb.h provides macros for reading/setting bitfields,
in macb registers and descriptors. use that instead
of redefining them in the source file.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Anup Patel <anup.patel@wdc.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
add support for clock rates higher than 2.4Mhz
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Anup Patel <anup.patel@wdc.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Few registers and bits were added by Cadence and
they were not updated in the headers.
Take the latest definitions as defined in Linux
header (5.1) that also includes some comments
about existing registers.
One register was improperly named (UR), fix that.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Anup Patel <anup.patel@wdc.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This driver is used for MDIO muxes driven over I2C. This is currently
used on Freescale LS1028A QDS board, on which the physical MDIO MUX is
controlled by an on-board FPGA which in turn is configured through I2C.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Using 'phy_connect' instead of 'phy_find_by_mask' and 'phy_connect_dev'
both deduplicates code and adds support for 'fixed-link'.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
SGMII 2500 as supported on NXP SoCs requires AN to be disabled, handle
this case in the enetc sgmii init code.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Ethernet interfaces using serial protocols go through the serdes block
integrated in the SoC. This is accessed over dedicated internal MDIOs
which are part of the Ethernet PCI functions. Set up serdes at _start,
along with other protocol specific port/MAC configuration.
MDIO code is shared with enetc_mdio, read/write functions are exported
from fsl_enetc_mdio for this reason.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adds a driver for the MDIO interface currently integrated in LS1028A SoC.
This MDIO interface is shared by multiple ethernet interfaces and is
presented as a stand-alone PCI function on the SoC ECAM.
Ethernet has a functional dependency on MDIO, for simplicity there is a
single config option for both.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adds a driver for NXP ENETC ethernet controller currently integrated in
LS1028A. ENETC is a fairly straight-forward BD ring device and interfaces
are presented as PCI EPs on the SoC ECAM.
Signed-off-by: Catalin Horghidan <catalin.horghidan@nxp.com>
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The fec_mxc.c driver can be reused by i.MX28 when DM_ETH is enabled.
One only needs to add proper compatible and dependency on FEC_MXC in the
Kconfig.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
The designware eth driver registers an mdio bus during probe, but if no
PHY is found, this bus is never removed although probe failes and the
driver is shown as not probed in the dm tree.
This later leads to errors when e.g. the mii or mdio commands try to
use available mdio buses because the mdio bus is still registered but
all corresponding data structures are invalid because probe failed.
Fix this by unregistering the mdio bus on probe failure (just as it is
unregistered in the .remove callback, too).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adds a test using a makeshift MDIO MUX. The test is based on the existing
MDIO test. It uses the last emulated PHY register to verify MUX selection.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This 2nd register is used by the follow-up MDIO MUX test.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adds a class for MDIO MUXes, which control access to a series of
downstream child MDIOs.
MDIO MUX drivers are required to implement a select function used to switch
between child buses.
MUX children are registered as MDIO buses and they can be used just like
regular MDIOs.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Current code fails to probe some C45 PHYs that also respond to C22 reads.
This is the case for PHYs like Aquantia AQR112, Marvell 88X2242 (as
previously posted on the u-boot list).
If the PHY ID reads all 0s just ignore it and try the next devad.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
adds AQR112 and AQR412 to the list of supported PHYs using existing AQR
code.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Macb can be used with Xilinx PCS/PMA PHY in fpga which is a 1000-baseX
phy(lpa 0x41e0). This patch adds checks for LPA_1000XFULL and
LPA_1000XHALF bits.
Signed-off-by: Radu Pirea <radu_nicolae.pirea@upb.ro>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If macb is gem and is gigabit capable, lpa value is not read from
the right register(MII_LPA) and is read from MII_STAT1000. This patch
fixes reading of the lpa value.
Signed-off-by: Radu Pirea <radu_nicolae.pirea@upb.ro>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add new driver for the TI AM65x SoC Gigabit Ethernet Switch subsystem (CPSW
NUSS). It has two ports and provides Ethernet packet communication for the
device and can be configured as an Ethernet switch. CPSW NUSS features: the
Reduced Gigabit Media Independent Interface (RGMII), Reduced Media
Independent Interface (RMII), and the Management Data Input/Output (MDIO)
interface for physical layer device (PHY) management. The TI AM65x SoC has
integrated two-port Gigabit Ethernet Switch subsystem into device MCU
domain named MCU_CPSW0. One Ethernet port (port 1) with selectable RGMII
and RMII interfaces and an internal Communications Port Programming
Interface (CPPI) port (Host port 0).
Host Port 0 CPPI Packet Streaming Interface interface supports 8 TX
channels and on RX channels operating by TI am654 NAVSS Unified DMA
Peripheral Root Complex (UDMA-P) controller.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use phys_addr_t for mdio_base address to avoid build
warnings on arm64 and dra7. Cast it to uintprt_t before
assigning to regs.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch is to use block layer to read from mmc in cortina
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Because all MSCC SoC use the same MDIO bus, put the implementation in
one common file(mscc_miim) and make all the other MSCC network drivers to
use these functions.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
A very simple test for DM_MDIO, mimicks a register write/read through the
sandbox bus to a dummy PHY.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adds UCLASS_MDIO DM class supporting MDIO buses that are probed as
stand-alone devices. Useful in particular for systems that support
DM_ETH and have a stand-alone MDIO hardware block shared by multiple
Ethernet interfaces.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When serdes configuration was written in hardware there was a delay
of 100ms to be sure that configuration was written. But the delay is not
needed because already the function serdes_write it is checking that the
operation finished.
Therefore remove the mdelay. This improves the speed of configuring the
network driver.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The code block reading the DT property for the clock output control was
before the phy's DT node pointer was set, so it could never work. Move
it after the node pointer is set.
Also store the unsigned 32-bit property into an unsigned value, not a
signed value, as the former will cause a problem if value overflows.
For instance, if one were to add 0xffffffff as a code to mean the clock
output should be turned off.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Janine Hagemann <j.hagemann@phytec.de>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When not using DM_ETH, these PHY settings are programmed with default
values hardcoded into the driver. When using DM_ETH, they should come
from the device tree. However, if the device tree does not have the
properties, the driver will silent use -1. Which is entirely out of
range, programs nonsense into the PHY's registers, and does not work.
Change this to use the same defaults as non-DM_ETH if the device tree is
lacking the properties.
As an alternative, the kernel driver for the phy will display an error
message and fail if the device tree is lacking.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Janine Hagemann <j.hagemann@phytec.de>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
- Add saveenv support for STM32MP1
- Add STM32MP1 Avenger96 board support
- Add SPI driver suport for STM32MP1
- Add watchdog support for STM32MP1
- Update power supply check via USB TYPE-C for STM32MP1 discovery board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2C9f
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20190606' of https://github.com/pchotard/u-boot
- Add Ethernet support for STM32MP1
- Add saveenv support for STM32MP1
- Add STM32MP1 Avenger96 board support
- Add SPI driver suport for STM32MP1
- Add watchdog support for STM32MP1
- Update power supply check via USB TYPE-C for STM32MP1 discovery board
We should not access reserved register on i.MX8, otherwise met SERROR
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Synopsys GMAC 4.20 is used. And Phy mode for eval and disco is RMII
with PHY Realtek RTL8211 (RGMII)
We also support some other PHY config on stm32mp157c
PHY_MODE (MII,GMII, RMII, RGMII) and in normal,
PHY wo crystal (25Mhz and 50Mhz), No 125Mhz from PHY config
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
At present the link speed change callback is a nop. According to
macb device tree bindings, an optional "tx_clk" is used to clock
the ethernet controller's TX_CLK under different link speed.
In 10/100 MII mode, transmit logic must be clocked from a free
running clock generated by the external PHY. In gigabit GMII mode,
the controller, not the external PHY, must generate the 125 MHz
transmit clock towards the PHY.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This updates DM version macb_linkspd_cb() signature for future
expansion, eg: adding an implementation for link speed changes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move the main symbol for Freescale Fman Ethernet controller option to
Kconfig. Also migrate the CONFIG_SYS_QE_FMAN_FW_IN_xxx macros and
rename the SPIFLASH one to follow the same format as all of the others.
To do this fully we need to migrate CONFIG_QC, do so.
Signed-off-by: Tom Rini <trini@konsulko.com>
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini <trini@konsulko.com>
In mt7629-rfb.dts, the phy-handle is a reference to the node phy0, not the
node itself:
phy-handle = <&phy0>;
phy0: ethernet-phy@0 {
reg = <0>;
}
However the driver used ofnode_find_subnode("phy-handle") to read the node.
It will always fail.
This patch replaces ofnode_find_subnode with dev_read_phandle_with_args to
make sure the node can be read correctly.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This version of the RTL-8168 is present on some development boards and
is compatible with this driver. Add support for identifying this version
of the chip so that U-Boot won't complain about it being unknown.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Implement this callback that allows the MAC address to be set for the
Ethernet card. This is necessary in order for the device to be able to
receive packets for the MAC address that U-Boot advertises.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
There is a need to fill node before clk_output_sel is setup.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Reviewed-by: <hannes.schmelzer@br-automation.com>
Commit d397f7c45b ("net: phy: micrel: Separate KSZ9000 drivers from
KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns
that you shouldn't select both of them due to a device ID clash between
the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a
system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately
boards like the SAMA5D3xEK do contain both types of PHY, but fortunately
the Linux Micrel PHY driver provides a solution by using different PHY
ID and mask values to distinguish these chips.
This commit contains the following changes:
- The PHY ID and mask values for the KSZ9021 and the KS8721 now match
those used by the Linux driver.
- The warnings about not enabling both drivers have been removed.
- The description for PHY_MICREL_KSZ8XXX has been corrected (these are
10/100 PHYs, not GbE PHYs).
- PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE
since this is selected by PHY_MICREL_KSZ90X1.
- All of the relevant defconfig files have been updated now that
PHY_MICREL_KSZ8XXX does not default to 'Y'.
Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In some of the device trees that specify skew values for KSZ90x1 PHYs
the values are stored (incorrectly) in the MAC node, whereas in others
it is in an 'ethernet-phy' subnode. Previously the code would fail to
find and program these skew values, so this commit changes it to look
for an "ethernet-phy" subnode first, and revert to looking in the MAC
node if there isn't one.
The device trees affected (where the skew values are in a subnode) are
imx6qdl-icore-rqs.dtsi, r8a77970-eagle.dts, r8a77990-ebisu.dts,
r8a77995-draak.dts, salvator-common.dtsi, sama5d3xcm.dtsi,
sama5d3xcm_cmp.dtsi, socfpga_cyclone5_vining_fpga.dts,
socfpga_stratix10_socdk.dts and ulcb.dtsi. Before this change the skew
values in these device trees would be ignored.
The device trees where the skew values are in the MAC node are
socfpga_arria10_socdk.dtsi, socfpga_arria5_socdk.dts,
socfpga_cyclone5_de0_nano_soc.dts, socfpga_cyclone5_de10_nano.dts,
socfpga_cyclone5_de1_soc.dts, socfpga_cyclone5_is1.dts,
socfpga_cyclone5_socdk.dts, socfpga_cyclone5_sockit.dts. These should be
unaffected by this change.
The changes were tested on a sama5d3xcm.
Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Commit ff7bd212cb ("net: phy: micrel: fix divisor value for KSZ9031
phy skew") fixed the skew value divisor for the KSZ9031, but left the
code using the same divisor for the KSZ9021, which is incorrect.
The preceding commit c16e69f702 ("net: phy: micrel: add documentation
for Micrel KSZ90x1 binding") added the DTS documentation for the
KSZ90x1, changing it from the equivalent file in the Linux kernel to
correctly state that for this part the skew value is set in 120ps steps,
whereas the Linux documentation and driver continue to this day to use
the incorrect value of 200 that came from the original KSZ9021 datasheet
before it was corrected in revision 1.2 (Feb 2014).
This commit sorts out the resulting confusion in a consistent way by
making the following changes:
- Update the documentation to be clear about what the skew values mean,
in the same was as for the KSZ9031.
- Update the Micrel PHY driver to select the appropriate divisor for
both parts.
- Adjust all the device trees that state skew values for KSZ9021 PHYs to
use values based on 120ps steps instead of 200ps steps. This will result
in the same values being programmed into the skew registers as the
equivalent device trees in the Linux kernel do, where it incorrectly
uses 200ps steps (since that's where all these device trees were copied
from).
Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
For AQR405 in register 4.c441 bit 15 was override with 0. This caused the
phy to not negotiate at 2.5GB rate with mac. To avoid
this override it needed first to know the previous value of reg 4.c441
and set only bit 3.
Signed-off-by: Valentin Catalin Neacsu <valentin-catalin.neacsu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Don't ignore return value of phy_probe() call as
the probe may fail and it needs to be reported.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch relocates the pointers inside phy_drivers incase
of manual reloc. Without this reloc, these points to invalid
pre relocation address and hence causes exception or hang.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
if an error occurs in ldpaa_eth_init, need to free all resources
before returning the error.
Threfore, free net_dev before returning from ldpaa_eth_init.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add EPHY CLK and RESET support for sun8i_emac driver to
enable EPHY TX clock and EPHY reset pins via CLK and RESET
framework.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Lothar Felten <lothar.felten@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When EEE is supported by the PHY and the driver allows it, libphy in the
kernel is configuring the PHY to stop receiving the xMII clock while it
is signaling LPI. While this (usually) works fine in the kernel this is
causing issues in U-Boot when rebooting from the linux kernel with this
bit set (without having the possibility to reset the PHY) where the PHY
suddenly stops working.
A new quirk is introduced to unconditionally reset this bit. If the
quirk is not enabled using the proper configuration symbol, the PHY state
is not changed.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Now that generic helpers are available, use those instead of relying on
ti specific functions.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Two new helper functions (phy_read_mmd() and phy_write_mmd()) are added
to allow access to the MMD PHY registers.
The MMD PHY registers can be accessed by several means:
1. Using two new MMD access function hooks in the PHY driver. These
functions can be implemented when the PHY driver does not support the
standard IEEE Compatible clause 45 access mechanism described in clause
22 or if the PHY uses its own non-standard access mechanism.
2. Direct access for C45 PHYs and C22 PHYs when accessing the reachable
DEVADs.
3. The standard clause 45 access extensions to the MMD registers through
the indirection registers (clause 22) in all the other cases.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add ifdeffery to allow operation without the clock framework
enabled. This is required on RZ/A1, as it does not have clock
driver yet.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for RZ/A1 SoC specifics.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
There are no more boards using this CPU and there is no prospect
of any boards showing up soon, remove it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Ocelot
- mt7620: rename arch to more generic name mtmips
- mips: pass initrd addresses via DT as physical addresses
-----BEGIN PGP SIGNATURE-----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=SZ/W
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2019-05-03' of git://git.denx.de/u-boot-mips
- mscc: small fixes, enhance network support for Serval, Luton and Ocelot
- mt7620: rename arch to more generic name mtmips
- mips: pass initrd addresses via DT as physical addresses
According to the R-Car Gen3 Hardware Manual Rev 1.50 of Nov 30, 2018, the
TX clock internal delay mode isn't supported on R-Car E3 (r8a77990) or D3
(r8a77995).
Avoid setting the APSR:TDM bit on these SoCs. Moreover, only set APSR:TDM
when the DT explicitly specifies RGMII ID or TXID mode instead of setting
it unconditionally when the PHY link speed is 1000 Mbit/s.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The boards with SoCs from the DaVinci DM* family used to come with
different PHYs that needed special support implemented in mach-davinci.
Since the support for these chips has long been removed, we can now
drop this unnused code from the emac driver.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Update Luton network driver to have support also for pcb90. The pcb90
has 24 ports from which 12 ports are connected to SerDes6G.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Currently mach-mt7620 contains only support for mt7628. To avoid confusion,
rename mach-mt7620 to mach-mtmips, which means MediaTek MIPS platforms.
MT7620 and MT7628 should be distinguished by SOC_MT7620 and SOC_MT7628
because they do not share the same lowlevel codes.
Dependencies of four drivers are changed to SOC_MT7628 as these drivers
are only used by MT7628.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Add network driver for Microsemi Ethernet switch.
It is present on Serval SoCs.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Rockchip use 'arch-rockchip' instead of arch-$(SOC) as common
header file path, so that we can get the correct path directly.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Since the introduction of the driver, some memory in IRAM is reserved for
the TX buffers.
However there are not used but instead of it, it is the buffer provided
by the net stack which is used. As stated in the comment of the driver,
not using the IRAM buffer could cause cache issue and lower the
throughput.
For the second argument it is less the case for transmitting buffers
because the throughput gain in IRAM is mitigated by the time to copy the
data from RAM to IRAM, but the first argument is still valid and indeed
this patch fixes issue seen with Ethernet on some boards
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
It adds the driver for HIGMACV300 Ethernet controller found on HiSilicon
SoCs like Hi3798CV200. It's based on a downstream U-Boot driver, but
quite a lot of code gets rewritten and cleaned up to adopt driver model
and PHY API.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When fixing sandbox test for regmap_read_poll_timeout(), the
sandbox_timer_add_offset was introduced but only defined in sandbox code
thus generating warnings when used out of sandbox :
include/regmap.h:289:2: note: in expansion of macro 'regmap_read_poll_timeout_test'
regmap_read_poll_timeout_test(map, addr, val, cond, sleep_us, \
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/spi/meson_spifc.c:169:8: note: in expansion of macro 'regmap_read_poll_timeout'
ret = regmap_read_poll_timeout(spifc->regmap, REG_SLAVE, data,
^~~~~~~~~~~~~~~~~~~~~~~~
drivers/spi/meson_spifc.c: In function 'meson_spifc_txrx':
include/regmap.h:277:4: warning: implicit declaration of function 'sandbox_timer_add_offset' [-Wimplicit-function-declaration]
This fix adds a timer_test_add_offset() only defined in sandbox, and
renames the previous sandbox_timer_add_offset() to it.
Cc: Simon Glass <sjg@chromium.org>
Reported-by: Tom Rini <trini@konsulko.com>
Fixes: df9cf1cc08 ("test: dm: regmap: Fix the long test delay")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
fpga:
- Add support for external data in FIT
- Extend testing for external data case
- Inform user about a need to run post config on Zynq
arm:
- Tune zynq command functions
- Fix internal variable setting
arm64:
- Add support for zc39dr decoding
- Disable WDT for zcu100
- Small changes in reset_reason()
- Some DT changes (spi)
- Tune qspi-mini configuration
- Remove useless eeprom setting
- Fix two sdhci boot case
spi:
- Fix tap delay programming
clk:
- Enable i2c in SPL
net:
- Fix gem phydev handling
- Remove phy detection code from gem driver
general:
- Correct EXT_DTB usage for MULTI_DTB_FIT configuration
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAly262oACgkQykllyylKDCH44gCbBnuxUH6ZF0B7Leuee4te7C59
LmUAn14/bbtMt17zkMSADCjY9yGWF4au
=mWrW
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2019.07' of git://git.denx.de/u-boot-microblaze
Xilinx/FPGA changes for v2019.07
fpga:
- Add support for external data in FIT
- Extend testing for external data case
- Inform user about a need to run post config on Zynq
arm:
- Tune zynq command functions
- Fix internal variable setting
arm64:
- Add support for zc39dr decoding
- Disable WDT for zcu100
- Small changes in reset_reason()
- Some DT changes (spi)
- Tune qspi-mini configuration
- Remove useless eeprom setting
- Fix two sdhci boot case
spi:
- Fix tap delay programming
clk:
- Enable i2c in SPL
net:
- Fix gem phydev handling
- Remove phy detection code from gem driver
general:
- Correct EXT_DTB usage for MULTI_DTB_FIT configuration
Add CLK and RESET support for sun8i_emac driver to
enable TX clock and reset pins via CLK and RESET
framework.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Lothar Felten <lothar.felten@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Unlike other Allwinner SoC's R40 GMAC clock control register
is locate in CCU, but rest located via syscon itself. Since
the phandle property for current code look for 'syscon' and
it will grab the respective ccu or syscon base address based
on DT property defined in respective SoC dtsi.
So, use the existing 'syscon' code even for R40 for retrieving
GMAC clock via CCU and update the register directly in
sun8i_emac_set_syscon instead of writing it separately using
ccm base.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Lothar Felten <lothar.felten@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add CLk support for sunxi_emac to enable AHB_EMAC clock
via CLK framework.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The phydev supported features were reset in phy_set_supported() so,
move the setting of driver supported features after this so that it
wont lost in phy_set_supported().
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
-----------
- DM support in sata
- Toradex Board to DM
- wandboard to DM
- tbs2910 to DM
- GE boards to DM
- VHybrid boards to DM
- DM_VIDEO for i.MX
-----BEGIN PGP SIGNATURE-----
iQHDBAABCgAtFiEEiZClFGvhzbUNsmAvKMTY0yrV63cFAly0NhIPHHNiYWJpY0Bk
ZW54LmRlAAoJECjE2NMq1et3XiUMALq2W4HPjFlDaVHpaxKIvZMkqAAjF7eE6M9l
DWivSm/Anm5jeE2UM80FpV7npdkPMcOl2YdcIjg+jMKKP6DI+4N6gEhWvxX9mEoC
RmR2nxGC/GIc0Blb4HU9V6xMkeR5jSAQ6bxZmX3IrnG6u67BIi4NmkNrT9gdQ+WT
PkJf2Ai7DN7+epfOzjO0d/LjS3hAVb+nesHuxoVraElwc5sEMAnoD0vIMUrXceZ2
+V6WiU1i9jeLj3fA8P+4o6wqQpxFLlJiuC0FUNKQH/kWIqX6MGrr9ElseLUV0O+Z
LL5nqsuTgG/fAol1r71De49fiML2Pfx7ZkAZOJ1NMUOXUKw25ulO/wi0wg8t+l2Z
2oAQ3S84RUVYX4MFLwxkBCq3uC9hvyCfWF1GmVLV6xSEulS6PnHx0FL6OTY4uB3h
bmVs/mutwwqYBaaoqGG4sG5L7TVSG/JxNgTVNh3Aqj5a89Fd9us+nBhLhoq6xyVl
cEf+/gPGQ97JEj9DolAPFIFQJBvL7g==
=KLsH
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20190415' of git://git.denx.de/u-boot-imx
Move to DM
-----------
- DM support in sata
- Toradex Board to DM
- wandboard to DM
- tbs2910 to DM
- GE boards to DM
- VHybrid boards to DM
- DM_VIDEO for i.MX
The NXP's FEC driver can be reused on vf610 device (with DM).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
- ath79: small fixes, add support for QCA9563 SoC and AP152 reference board
- mscc: small fixes, add network support for JR2 and ServalT SoCs
- bmips: small fixes, enable more drivers for ARM specific BCM6858 and BCM63158 SoCs
- MIPS: fix redundant relocation of initrd images
-----BEGIN PGP SIGNATURE-----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=NrV8
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2019-04-12' of git://git.denx.de/u-boot-mips
- mt76xx: add USB support, small fixes
- ath79: small fixes, add support for QCA9563 SoC and AP152 reference board
- mscc: small fixes, add network support for JR2 and ServalT SoCs
- bmips: small fixes, enable more drivers for ARM specific BCM6858 and BCM63158 SoCs
- MIPS: fix redundant relocation of initrd images
Add network driver for Microsemi Ethernet switch.
It is present on ServalT SoCs.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add network driver for Microsemi Ethernet switch.
It is present on Jaguar2 SoCs.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
S17 ethernet support is for QCA8337N, which used on
AP152 (QCA9563) board. It is a 7 ports GbE switch.
Signed-off-by: Rosy Song <rosysong@rosinson.com>
Changes for v2-v3:
- add more commit message for s17
Changes for v4-v5:
- coding style cleanup
The function mscc_miim_reset resets all the phys, but it is called for
each phy separetely. One consequence of this is that the boot time
is increased by 2 seconds.
The fix consists for calling the mscc_miim_reset function only once for
all phys.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The SPL image overflows when cpsw dt nodes are added and SPL_OF_CONTROL
is enabled. Use static platdata instead to save space.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
The ofdata_to_platdata function should not be called if OF_CONTROL is
not enabled because fdtdec_* calls will fail. Block the function with
OF_CONTROL
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
ti_cm_get_macid() is used to get a syscon node from the dt, read the
efuse address and then assign the macid read from the address. Divide
these two steps into separate functions one of which can be called from
ofdata_to_platdata() while the other can be called from _probe(). This
ensures that platdata can be assigned statically in a board file when
OF_CONTROL is not enabled. Also add a macid_sel_compat in private data
to get information about the macid byte placement.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Convert cpsw_platform_data to a pointer in cpsw_priv. Allocate it
dynamically and assign it as a part of eth_pdata. This helps in
isolating platform data handling and implementing platdata for SPL
in a board file.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
cpsw_phy_sel() is a configuration step that should not be in
ofdata_to_platdata(). Add phy_sel_compat to the cpsw_platform_data
structure so that it is accessible in _probe. Then move the call of
cpsw_phy_sel() to _probe.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Enhance the netcp driver to support phys that can be configured
for internal delay (rgmii-id, rgmii-rxid, rgmii-txid)
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reset and initialize the PHY once in the probe() function rather than
doing it over and over again is start() function. This requires us to
keep the clock enabled while the driver is in use. This significantly
reduces the time between transfers as the PHY doesn't have to restart
autonegotiation between transfers, which takes forever.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
I've noticed that the first ethernet packet after PHY link establishment
is not tranferred correctly most of the time on my AT91SAM9G25 board.
Here I usually see a timeout of a few seconds, which is quite
annoying.
Adding a small delay (10ms in this case) after the link establishment
helps to solve this problem. With this patch applied, this timeout
on the first packet is not seen any more.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
As per Linux kernel DT binding doc:
- phy-reset-post-delay : Post reset delay in milliseconds. If present then
a delay of phy-reset-post-delay milliseconds will be observed after the
phy-reset-gpios has been toggled. Can be omitted thus no delay is
observed. Delay is in range of 1ms to 1000ms. Other delays are invalid.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Negative phy-addresses can occour if the caller function was not able to
determine a valid phy address (from device-tree for example). In this
case we catch this here and search for ANY phy device on the given mdio-
bus.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Lukasz Majewski <lukma@denx.de>
If node /board_info/ports does not exist in the DPC file,
function mc_fixup_dpc() will skip not only MAC address fixup,
but also the cache flush at the end. This may cause the other
fixup changes (e.g. ICID related ones) to be ignored by MC.
Fixes: 1161dbcc0a ("drivers: net: fsl-mc: Include MAC addr fixup to DPL")
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
some dpmacs in armv8a based freescale layerscape SOCs can be
configured via both serdes(sgmii, xfi, xlaui etc) bits and via
EC*_PMUX(rgmii) bits in RCW.
e.g. dpmac 17 and 18 in LX2160A can be configured as SGMII from
serdes bits and as RGMII via EC1_PMUX/EC2_PMUX bits
Now if a dpmac is enabled by serdes bits then it takes precedence
over EC*_PMUX bits. i.e. in LX2160A if we select serdes protocol
that configures dpmac17 as SGMII and set the EC1_PMUX as RGMII,
then the dpmac is SGMII and not RGMII.
Therefore, in fsl_rgmii_init function of SOC, we will check if the
dpmac is enabled or not? if it is (fsl_serdes_init has already enabled
the dpmac), then don't enable it.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The phy_connect_dev(...) function from phy.c does all the handling
(inclusive catching fixed-link).
So we drop here the single steps and call just phy_connect_dev(...).
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fix MID bit field check to correctly identify all GEM hardwares.
The check is updated as per macb driver in Linux location:
<linux_sources>/drivers/net/ethernet/cadence/macb_main.c:259
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Don't fail in macb_enable_clk() if clk_enable() returns
-ENOSYS because we get -ENOSYS for fixed-rate clocks.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable the socfpga specific designware ethernet driver by default for
socfpga by implying it when enabling CONFIG_ETH_DESIGNWARE for a
MACH_SOCFPGA config.
This is required to remove the hacky reset and phy mode handling in
arch/arm/mach-socfpga.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This driver was written for Arria10, but it applies to Gen5, too.
The main difference is that Gen5 has 2 MACs (Arria10 has 3) and the
syscon bits are encoded in the same register, thus an offset is needed.
This offset is already read from the devicetree, but for Arria10 it is
always 0, which is probably why it has been ignored. By using this
offset when writing the phy mode into the syscon regiter, we can use
this driver to set the phy mode for both of the MACs on Gen5.
Since the PHY mode bits in sysmgr are the same even for Stratix10,
let's drop the detection of the sub-mach by checking compatible
version and just use the same code for all FPGAs.
To work correctly, this driver depends on SYSCON and REGMAP, so select
those via Kconfig when it is enabeld.
Tested on socfpga_socrates (where the 2nd MAC is connected, so a shift
offset is required).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
phy_reset should be called before autoneg is setup
The only boards using MV88E61XX_SWITCH are:
- alliedtelesis/SBx81LIFKW
- alliedtelesis/SBx81LIFXCAT
- gateworks/gw_ventana
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
When DM_REGULATOR is enabled, the driver attempts to call
regulator_autoset() which expects the regulators to be on at boot
and/or always on and fails if they are not true.
For a more generic approach, this patch just calls
regulator_set_enable() which shouldn't have such restrictions.
Fixes: ad8c43cbca ("net: dm: fec: Support the phy-supply
binding")
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This functions can be reused by other MSCC SoCs therefore,
make them more generic and move them in separate files.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Move file ocelot_switch to mscc_eswitch to prepare to add
new net drivers for other MSCC SoCs.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Currently if we have more than one phy on the MDIO bus, we do not have a
good mechanism for determining which should be used at runtime. Enable the
FEC driver to determine the address for the PHY from the device tree.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Print information about Aquantia system interface and firmware loaded
on the phy.
Signed-off-by: Valentin Catalin Neacsu <valentin-catalin.neacsu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If System Interface protocol is USXGMII then enable USXGMII autoneg
Signed-off-by: Valentin Catalin Neacsu <valentin-catalin.neacsu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
No mainline board enables CONFIG_MCAST_TFTP and there have been
compilation issues with the code for some time. Additionally, it has a
potential buffer underrun issue (reported as a side note in
CVE-2018-18439).
Remove the multicast TFTP code but keep the driver API for the future
addition of IPv6.
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
ether_crc was added to the core net code in commit 53a5c424bf
("multicast tftp: RFC2090") so that other drivers could use it. However
the only current user of it is tsec.c so move it there.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
According to the datasheet to access the extended registers we have to:
1. Write Register 31 Data = 0x0XYZ (Page 0xXYZ)
2. Read/Write the target Register Data
3. Write Register 31 Data = 0x0000 or 0xa42 (switch back to IEEE
Standard Registers)
Hook the missing functions so that we can use the `mdio rx/wx` command to
easily access the extended registers.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch add GPIO configuration support in mvneta driver.
Driver will handle PHY reset. GPIO pins should be set in device tree.
Ported from mvpp2x
[https://patchwork.ozlabs.org/patch/799654/]
Initial discussion to port the changes into mvneta
[https://patchwork.ozlabs.org/patch/1005765/]
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
Tested-by: Dennis Gilmore <dgilmore@redhat.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Some existing device trees don't specify a phy-mode so fallback to GMII
when a phy-mode is not provided.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
For KSZ9021, all skew register fields are 4-bit wide.
For KSZ9031, the clock skew register fields are 5-bit wide.
The common code in ksz90x1_of_config_group calculating the combined
register value checks if the requested value is above the maximum
and uses this maximum if so. The calculation of this maximum uses
the register width, but the check itself does not. It uses a hardcoded
value of 0xf, which is too low in case of the 5-bit clock (0x1f).
This detail was probably lost during driver unification.
Effect (only for KSZ9031 clock skews): For values greater 900 (== 0ps),
this silently results in 1860 (== +960ps) instead of the requested one.
Fix the check by using the bit width instead of hardcoded value(s).
Signed-off-by: Andreas Pretzsch <apr@cn-eng.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Current code forces all ports on a given Ethernet device to use the same
mdio device. In practice different ports might be wired to separate mdio
devices. Move the mdio device from the container struct mvpp2 to the per
port struct mvpp2_port.
Cc: Ken Ma <make@marvell.com>
Cc: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Current mdio base lookup code relies on a 'reg' property at the upper CP
node. There is no 'reg' property there in current DT files of Armada
CP110. Use ofnode_get_addr() instead since it provides proper DT address
translation.
Cc: Ken Ma <make@marvell.com>
Cc: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Short frames are padded to the minimum allowed size of 60 bytes.
However, the designware driver sends old data in these padding bytes.
It is common practice to zero out these padding bytes ro prevent
leaking memory contents to other hosts.
Fix the padding code to zero out the padded bytes at the end.
Tested on socfpga gen5.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The designware driver has a bug in setting the tx length into the dma
descriptor: it always or's the length into the descriptor without
zeroing out the length mask before.
This results in occasional packets being transmitted with a length
greater than they should be (trailer). Due to the nature of Ethernet
allowing such a trailer, most packets seem to be parsed fine by remote
hosts, which is probably why this hasn't been noticed.
Fix this by correctly clearing the size mask before setting the new
length.
Tested on socfpga gen5.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The phy devices can be accessed via clause 22 or via clause 45.
This information can be deduced when we read phy id. if the phy id
is read without giving any MDIO Manageable Device Address (MMD), then
it conforms to clause 22. otherwise it conforms to clause 45.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch moves fixed-link functionality code to a separate
routine inorder to make it more modular and cleaner.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The cache was only flushed before *transmitting* packets, but not
when receiving them, leading to an issue where new packets were
handed to the receive handler with old contents in cache. This
only happens when a lot of packets are received without sending
packages every now and then. Also flushing the receive buffers
in the transmit function makes no sense and can be removed.
Signed-off-by: Stefan Theil <stefan.theil@mixed-mode.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for the Microsemi Ethernet switch present on
Ocelot SoCs.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
fsl-mc lazyapply command applies dpl from efi_exit_boot_services().
Status of fsl-mc node in working fdt is updated at this stage.
However, an efi application like grub may already have copied the fdt.
So the updates to fdt done at efi_exit_boot_services() may not be
visible to the OS. Fix it by updating fdt earlier if fsl-mc lazyapply
command is used.
Fixes: b7b8410a8f (ls2080: Exit dpaa only right before exiting U-Boot)
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
Buildman clang support and a few fixes
Small fixes to 'dm tree' and regmap test
Improve sandbox build compatibility
A few other minor fixes
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlw+AlIACgkQfxc6PpAI
reYchAf+L/P5JsLoCKAY84v11eWQkCS44idAYStD8Q023dyuyNC/W6G3qEQVGkHu
SXBzNrZ5wSJanN5I3h3ktJ7yfMOYIvSO2qLHphxDstPaZbCY4Zac6NywHrHxQpA9
fbSilQRbcVWrPo5rsjjZhXmMdQRZVOmGD6CYZj1AihWAiHfYth7f6laNWNTWQA8C
z+aoiF70t/PbvwFbgdzzYOjoGdXI9XML0xTqdLWRlsBKjf3z54pCV6LmN2xrsrDZ
k7lr+x7ajJUFhivxzjowf4aOjhDB+/+I3sr+hJ5vkMM0Kqg14bbEU+xJRGpDc18K
QPvVHT5JGe/nq1cZXuCqzrYxTrrA7A==
=w9ln
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-15jan19' of git://git.denx.de/u-boot-dm
Fix recent changes to serial API for driver model
Buildman clang support and a few fixes
Small fixes to 'dm tree' and regmap test
Improve sandbox build compatibility
A few other minor fixes
At present this stores the error number in an unsigned int so an error is
never detected. Use the existing signed variable instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds ethernet support for Mediatek ARM-based SoCs, including
a minimum setup of the integrated switch.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Mark Lee <Mark-MC.Lee@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Tested-By: "Frank Wunderlich" <frank-w@public-files.de>
When fixed-link phy is used subnode offset is used as phy address. This
number is bigger then space allocated for bus structure (allocated via
mdio_alloc).
bus->phymap[] array has PHY_MAX_ADDR size (32).
That's why writing bus->phymap[addr] where addr is < 0 or > PHY_MAX_ADDR
is causing write to memory which can caused full U-Boot crash.
The patch is checking if address is in correct range.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for lx2160a SoC
-----BEGIN PGP SIGNATURE-----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=aT7d
-----END PGP SIGNATURE-----
Merge tag 'fsl-qoriq-for-v2019.01-rc2' of git://git.denx.de/u-boot-fsl-qoriq
Add TFA boot flow for some Layerscape platforms
Add support for lx2160a SoC
[trini: Add a bunch of missing MAINTAINERS entries]
Signed-off-by: Tom Rini <trini@konsulko.com>
This merges the CRC16-CCITT headers into u-boot/crc.h to prepare for
rolling CRC16 into the hash infrastructure. Given that CRC8, CRC32
and CRC32-C already have their prototypes in a single header file, it
seems a good idea to also include CRC16-CCITT in the same.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Adds TFABOOT support and allows to pick FMAN firmware
on basis of boot source.
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[YS: fix checkpatch issues]
Reviewed-by: York Sun <york.sun@nxp.com>
tpm improvements to clear up v1/v2 support
buildman toolchain fixes
New serial options to set/get config
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlwIe0gRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreY02wgAjK9U1ADmoNi4xWgtq83EerxOGTq68BRD
CfnUDgI+FQHNv/LxdZ8lZ2lgGG1xXZ8mdeHWghllHoLEnwMQ3LxfDRnpkyC6VBE9
LvZF4F7BhTnGsKImlloQ5oMhKI4sDKjqRkRL3D633x5dq9Z571obAyGwLMo67vv6
U8iv1mRMr6au46pLvH25DF6h5LuM7TBSJVDlzmFmmD++r/YDroTJfo07qdo8sNqS
0hDPjgp3uqf1mX2cbNHk56a3DmO9fL6Gcvdv0LHGQvRyfQ36TY+cEcDU2y2p+tl+
t1LFamfZvalix9AyJegr3qGMOb9B20ar89EItXzH9J+ahnlZmEat+w==
=VAMW
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5dec18' of git://git.denx.de/u-boot-dm
Minor sandbox enhancements / fixes
tpm improvements to clear up v1/v2 support
buildman toolchain fixes
New serial options to set/get config
We cannot be sure that the interface name takes up the full length of the
space available to it. Use strcpy() instead of memcpy() in this case. This
corrects a valgrind warning.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch throws an error if 64-bit support is expected
but DMA hardware is not capable of 64-bit support. It also
prints a debug message if DMA is capable of 64-bit but not
using it.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
This patch adds 64-bit addressing support for zynq gem.
This means it can perform send and receive operations on
64-bit address buffers.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Some boards have the EMAC TX/RX lanes wired with a different length with
the clock lane, which can be workarounded by setting a TX/RX delay in
the EMAC.
This kind of delays are already defined in the newest device tree
binding of dwmac-sun8i, which has already entered linux-next.
Add support for setting these delays.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Update TI Keystone 2 driver to re-use common mdio lib.
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Update TI CPSW driver to re-use common mdio lib
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
All existing TI SoCs network HW have similar MDIO implementation, so
introduce common mdio support library which can be reused by TI networking
drivers.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Update to use SPDX license identifier.
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Networking support for all TI K2 boards converted to use DM model and
CONFIG_DM_ETH enabled in all corresponding defconfig files, hence drop
unused non DM K2 networking code.
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Add drivers/net/ti/ folder and move all TI's code in this folder for better
maintenance.
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
The VSC8574 PHY is a 4-port PHY that is 10/100/1000BASE-T, 100BASE-FX,
1000BASE-X and triple-speed copper SFP capable, can communicate with
the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and
can set the blinking pattern of each of its 4 LEDs, supports SyncE as
well as HP Auto-MDIX detection.
This adds support for 10/100/1000BASE-T and SGMII/QSGMII link with the
MAC.
The VSC8574 has also an internal Intel 8051 microcontroller whose
firmware needs to be patched when the PHY is reset. If the 8051's
firmware has the expected CRC, its patching can be skipped. The
microcontroller can be accessed from any port of the PHY, though the CRC
function can only be done through the PHY that is the base PHY of the
package (internal address 0) due to a limitation of the firmware.
The GPIO register bank is a set of registers that are common to all PHYs
in the package. So any modification in any register of this bank affects
all PHYs of the package.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Part of the config is common between the VSC8584 and the VSC8574, so to
prepare for the upcoming support of VSC8574, use the phy_device.priv
pointer that will keep the function that holds code that is PHY-specific
and that should be called during config function.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The VSC8584 PHY is a 4-port PHY that is 10/100/1000BASE-T, 100BASE-FX,
1000BASE-X and triple-speed copper SFP capable, can communicate with the
MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set
the blinking pattern of each of its 4 LEDs, supports hardware offloading
of MACsec and supports SyncE as well as HP Auto-MDIX detection.
This adds support for 10/100/1000BASE-T and SGMII/QSGMII link with the
MAC.
The VSC8584 has also an internal Intel 8051 microcontroller whose
firmware needs to be patched when the PHY is reset. If the 8051's
firmware has the expected CRC, its patching can be skipped. The
microcontroller can be accessed from any port of the PHY, though the CRC
function can only be done through the PHY that is the base PHY of the
package (internal address 0) due to a limitation of the firmware.
The GPIO register bank is a set of registers that are common to all PHYs
in the package. So any modification in any register of this bank affects
all PHYs of the package.
The revA of the VSC8584 PHY (which is not and will not be publicly
released) should NOT patch the firmware of the microcontroller or it'll
make things worse, the easiest way is just to not support it.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The Faraday ftgmac100 MAC controllers as found on the Aspeed SoCs have
some slight differences in the HW interface (End-Of-Rx/Tx-Ring bits).
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use simple arrays under the device priv structure to hold the RX and
TX descriptors and handle memory coherency by invalidating or flushing
the d-cache when required.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Implement the MDIO bus read/write functions using the readl_poll_timeout()
routine, initialize the bus and scan for the PHY. RGMII and RMII mode
are supported.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The driver is based on the previous one and the code is only adapted
to fit the driver model. The support for the Faraday ftgmac100
controller is the same with MAC and MDIO bus support for RGMII/RMII
modes.
Configuration is updated to enable compile again. At this stage, the
driver compiles but is not yet functional.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds ethernet support for the MIPS based Mediatek MT76xx SoCs
(e.g. MT7628 and MT7688), including a minimum setup of the integrated
switch. This driver is loosly based on the driver version included in
this MediaTek github repository:
https://github.com/MediaTek-Labs/linkit-smart-uboot.git
Tested on the MT7688 LinkIt smart-gateway and on the
Gardena-smart-gateway.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Frank Wunderlich <frankwu@gmx.de>
Cc: Weijie Gao <hackpascal@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Per T1040RM (Rev. 1, 08/2015), there are 2 issues with the RCW EC2
settings.
- The value of FSL_CORENET_RCWSR13_EC2_FM1_GPIO is wrong and should
be 0x04000000 (value of 1 in RCW bit [420:421])
- Value of 2/3 are reserved in RCW bit [420:421], hence there is no
macro FSL_CORENET_RCWSR13_EC2_FM1_DTSEC5_MII.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Poonam Aggrwal <poonam.aggrwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Complete in the drivers directory the work started with
commit 83d290c56f ("SPDX: Convert all of our single
license tags to Linux Kernel style").
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add compatible property and enable the FEC ipg clock when probing
on i.MX8X. Add specific function for reading FEC clock rate via
clock driver when configuring MII speed register. Allow FEC_MXC
selection for i.MX8.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The default Linux PHY reset delay is 10ms. This is also the requirement
for Marvell 88E151x PHYs, which are likely to be used with this Ethernet
MAC.
Cc: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The dm_gpio_set_value() call sets the logical level of the GPIO signal.
That is, it takes the GPIO_ACTIVE_{LOW,HIGH} property into account. The
driver needs to assert the reset, and then deassert it. Not the other
way around.
Cc: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The DT property "phy-mode" already provides the transceiver type.
Use it so that we do not have to also set CONFIG_FEC_XCV_TYPE
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Configure the phy regulator if defined by the "phy-supply" DT phandle.
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The DT binding says:
- phy-reset-duration : Reset duration in milliseconds. Should present
only if property "phy-reset-gpios" is available. Missing the property
will have the duration be 1 millisecond. Numbers greater than 1000 are
invalid and 1 millisecond will be used instead.
However the current code:
- clamps values greater than 1000ms to 1000ms rather than 1.
- does not initialize the delay if the property does not exist
(else clause mismatch)
- returns an error if phy-reset-gpios is not defined
Fix all this and simplify by using dev_read_u32_default()
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The DT binding says that phy-reset-duration is in ms, but the driver
currently uses udelay().
Switch to mdelay() to fix this.
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If the phy reports a valid firmware version and doesn't indicate
a fault, skip loading the firmware. This allows the same image
to be used on boards that have firmware storage and those that do not.
Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Aquantia phys have firmware that can be loaded automatically
from storage directly attached to the phy or via MDIO commands.
Add support for loading firmware from either a file or a
raw location on an MMC device.
Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G.
Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Xilinx SoC Versal is using fixed clock where setting rate is not supported.
That's why workaround the driver till real clock driver is supported.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Xilinx is introducing Versal, an adaptive compute acceleration platform
(ACAP), built on 7nm FinFET process technology. Versal ACAPs combine
Scalar Processing Engines, Adaptable Hardware Engines, and Intelligent
Engines with leading-edge memory and interfacing technologies to deliver
powerful heterogeneous acceleration for any application. The Versal AI
Core series has five devices, offering 128 to 400 AI Engines. The series
includes dual-core Arm Cortex™-A72 application processors, dual-core Arm
Cortex-R5 real-time processors, 256KB of on-chip memory with ECC, more
than 1,900 DSP engines optimized for high-precision floating point with
low latency.
The patch is adding necessary infrastructure in place without enabling
platform which is done in separate patch.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We need to #ifdef some variables to avoid warning about them being
unused.
Fixes: 1a048cd656 ("driver: net: fsl-mc: Add support of multiple phys for dpmac")
Signed-off-by: Tom Rini <trini@konsulko.com>
Till now we have had cases where we had one phy device per dpmac.
Now, with the upcoming products (LX2160AQDS), we have cases, where there
are sometimes two phy devices for one dpmac. One phy for TX lanes and
one phy for RX lanes. to handle such cases, add the support for multiple
phys in ethernet driver. The ethernet link is up if all the phy devices
connected to one dpmac report link up. also the link capabilities are
limited by the weakest phy device.
i.e. say if there are two phys for one dpmac. one operates at 10G without
autoneg and other operate at 1G with autoneg. Then the ethernet interface
will operate at 1G without autoneg.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The dpmac initalization should not depend on phy.
As the phy is not necessary to be present for dpmac to function.
Therefore, remove dpmac initialization dependency from phy.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
when there is no phy present for a dpmac, a dummy phy device is created.
when we move to multiple phy method, we need to create as many dummy phy
devices.
Change this method so that we don't need to create dummy phy devices.
We always report linkup if no phy is present.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
if an error occurs during init_phy, we should free the phydev structure
which has been allocated by phy_connect.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The phydev structure is present in both ldpaa_eth_priv and
wriop_dpmac_info. the phydev in wriop_dpmac_info is not being used
As the phydev is created based on phy_addr and bus members of
wriop_dpmac_info, it is appropriate to keep phydev in wriop_dpmac_info.
Also phy_regs is not being used, therefore remove it
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The goto label name is misspelled it should be DPMAC not DPAMC
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The target will respond to pings while doing other network handling.
Make sure that the response happens and is correct.
This currently corrupts the ongoing operation of the device if it
happens to be awaiting an ARP reply of its own to whatever serverip it
is attempting to communicate with. In the test, add an expectation that
the user operation (ping, in this case) will fail. A later patch will
address this problem.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This tests that ARP requests made to this target's IP address are
responded-to by the target when it is doing other networking operations.
This currently corrupts the ongoing operation of the device if it
happens to be awaiting an ARP reply of its own to whatever serverip it
is attempting to communicate with. In the test, add an expectation that
the user operation (ping, in this case) will fail. A later patch will
address this problem.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tests need to be able to pass their "unit test state" to the handlers
where asserts are evaluated. Add a function that allows the tests to set
this private data on the sandbox eth device.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use up to the max allocated receive buffers so as to be able to test
more complex situations.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If tests want to implement tx handlers, they will likely need access to
the details in the priv structure.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Make the send handler registerable so tests can check for different
things.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Store the per-device data with the device.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The DP83867 has a muxing option for the CLK_OUT pin. It is possible
to set CLK_OUT for different channels.
Create a binding to select a specific clock for CLK_OUT pin.
Based on commit 9708fb630d19 ("net: phy: dp83867: Add binding for
the CLK_OUT pin muxing option") of mainline linux kernel.
Signed-off-by: Janine Hagemann <j.hagemann@phytec.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The DP83867 when not properly bootstrapped - especially with LED_0 pin -
can enter N/A MODE4 for "port mirroring" feature.
To provide normal operation of the PHY, one needs not only to explicitly
disable the port mirroring feature, but as well stop some IC internal
testing (which disables RGMII communication).
To do that the STRAP_STS1 (0x006E) register must be read and RESERVED bit
11 examined. When it is set, the another RESERVED bit (11) at PHYCR
(0x0010) register must be clear to disable testing mode and enable RGMII
communication.
Thorough explanation of the problem can be found at following e2e thread:
"DP83867IR: Problem with RESERVED bits in PHY Control Register (PHYCR) -
Linux driver"
https://e2e.ti.com/support/interface/ethernet/f/903/p/571313/2096954#2096954
Based on commit ac6e058b75be ("net: phy: dp83867: Recover from "port mirroring"
N/A MODE4") of mainline linux kernel.
Signed-off-by: Janine Hagemann <j.hagemann@phytec.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
This patch adds support for enabling or disabling the lane swapping
(called "port mirroring" in PHY's CFG4 register) feature of the DP83867
TI's PHY device.
One use case is when bootstrap configuration enables this feature (because
of e.g. LED_0 wrong wiring) so then one needs to disable it in software
(at u-boot/Linux).
Based on commit fc6d39c39581 ("net: phy: dp83867: Add lane swapping
support in the DP83867 TI's PHY driver") of mainline linux kernel.
Signed-off-by: Janine Hagemann <j.hagemann@phytec.de>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
There are plenty of existing drivers that have macros like ETH_ALEN
defined in their own source files. Now that we imported the kernel's
if_ether.h to U-Boot we can reduce some duplication.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Currently there are two ethernet drivers (mvneta.c and mvpp2.c) that
has netdev_### (eg: netdev_dbg) log macros defined in its own driver
file. This adds these log macros in a common place linux/compat.h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Using PHY internal delays in combination with the phy-mode
rgmii-id/rxid/txid was not possible. Only rgmii was supported.
Now we can disable rockchip's gmac delay lines and also use
rgmii-id/rxid/txid.
Based on commit eaf70ad14cbb ("net: stmmac: dwmac-rk: Add
handling for RGMII_ID/RXID/TXID") for mainline linux kernel.
Signed-off-by: Janine Hagemann <j.hagemann@phytec.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
We have to use RK3328_RXCLK_DLY_ENA_GMAC_ENABLE instead of
RK3328_RXCLK_DLY_ENA_GMAC_MASK in rk3328_gmac_set_to_rgmii()
to enable the RX delay.
The MASK was used in a wrong way.
Signed-off-by: Janine Hagemann <j.hagemann@phytec.de>
Reviewed-by: Philipp Tomisch <philipp.tomisch@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
LS1043A, LS1046A, LS1088A, LS2088A.
Switch to driver model for SATA on LS1021A and LS1043A.
Add support for LS1012AFRWY rev C board.
Enable SMMU for LS1043A.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XRFI
-----END PGP SIGNATURE-----
Merge tag 'fsl-qoriq-for-v2018.11-rc1' of git://git.denx.de/u-boot-fsl-qoriq
Switch to driver model for eSDHC on Layerscape SoCs including LS1021A,
LS1043A, LS1046A, LS1088A, LS2088A.
Switch to driver model for SATA on LS1021A and LS1043A.
Add support for LS1012AFRWY rev C board.
Enable SMMU for LS1043A.
Recently the FMan Port and MAC compatibles were changed. This patch
aligns the FMan Port and MAC compatibles to the new FMan device tree
binding document. The FMan device tree binding document can be found
in the Linux kernel version 3.18.0, commit
297d35fd2a7d3fbd4e5c0f0c1c18213117ba11ba
./Documentation/devicetree/bindings/powerpc/fsl/fman.txt
This patch doesn't affect legacy compatibles support.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
[York S: reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Memory reserved for Management Complex needs to be cleaned before any
usage.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[York S: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
The iommu-map property in the fsl-mc node is updated by
valid stream-ids by u-boot. This patch is to fixup this
property for LS208x and LS1088.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
At present the MMC subsystem maintains its own list of MMC devices.
This cannot work with driver model when CONFIG_BLK is enabled, use
blk_dread to replace previous mmc read interface, use
mmc_get_blk_desc to get the mmc device property.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
[York S: reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Based on dt-specs fixed-link doesn't require phy-handle to be used.
Fix driver to only read phy related setting when phy-handle is found.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
max-speed property is part of phynode and it has to be
read using ofnode_read_u32_default(). This fixes the issue
of incorrect max-speed read from DT.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
On some boards using TI CPSW, it may be possible that
PHY address was not latched correctly, and the actual
address that the phy responds on is different from that
set in device-tree. For example, see this problem report
on beaglebone black:
https://groups.google.com/d/msg/beagleboard/9mctrG26Mc8/1FuI_i5KW10J
Add support to check for this condition and use the
detected phy address when its safe to do so.
Also, add a public API that exposes the phy address of
a given slave. This can be used to update device-tree that
is passed to Linux kernel.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMAC
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
