Cleaning up the clocks layer.
This helps in addition of new Soc with minimal
changes.
This is derived from OMAP4 boards.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Locking sequence for all the dplls is same.
In the current code same sequence is done repeatedly
for each dpll. Instead have a generic function
for locking dplls and pass dpll data to that function.
This is derived from OMAP4 boards.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
NOR requires that s_init be within the first 4KiB of the image so that
we can perform the rest of the required pinmuxing to talk with the rest
of NOR that we are found on. When NOR_BOOT is set we save our
environment in NOR at 512KiB and a redundant copy at 768KiB. We avoid
using SPL for this case and u-boot.bin is written directly to the start
of NOR.
We enclose the DMM-related parts of arch/arm/cpu/armv7/am33xx/emif4.c
with TI81xx checks as at this time U-Boot does not discard unused
sections in the main build and this code relies on functions specific to
(and only provided in) ti81xx-related code.
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds support for the NOR module that attaches
to the memory cape for a Beaglebone board. This does not
add booting support; only support so that you can boot from
SD/MMC and see the NOR module so that it can be programmed.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
[trini: Clean up config changes slightly]
Signed-off-by: Tom Rini <trini@ti.com>
We rework the various board_is_foo() checks to take a pointer to
struct am335x_baseboard_id rather than using a local copy in board.c.
This allows us to make use of the same checks in mux.c as well as fixing
problems when this code could be running from read-only memory.
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Tom Rini <trini@ti.com>
The AM335x GP EVM ships with NAND. Document programming of the chip
including the redundant locations that the ROM will check.
Signed-off-by: Tom Rini <trini@ti.com>
As reported in http://marc.info/?l=u-boot&m=137358037827735&w=2
There is no need for the "xMB" variant, as the gpio pins used for
identification where never changed from the xMA when the newer silcon
was used for the xMB, So rename XM A revision as AB revision
and report accordingly
Reported-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
BD ram address may vary in various SOC, so removing the hardcoding and
passing the same information through platform data
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Add a README for the family of boards the am335x_evm covers, and include
instructions on preparing and using falcon mode, for various media.
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Fix the checkpatch warning on the panda.c file for leading
spaces.
Fix the CHECK warnings on the panda.c file for parenthesis alignment.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Detect if we are running on a panda revision A1-A6,
or an ES panda board. This can be done by reading
the level of GPIOs and checking the processor revisions.
This should result in:
Panda 4430:
GPIO171, GPIO101, GPIO182: 0 1 1 => A1-A5
GPIO171, GPIO101, GPIO182: 1 0 1 => A6
Panda ES:
GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 0 1 1 => B1/B2
GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 1 1 1 => B3
Set the board name appropriately for the board revision that
is detected.
Update the findfdt macro to load the a4 device tree binary.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
[trini: %s/CONTROL_PADCONF_CORE/(*ctrl)->control_padconf_core_base/ and
formatting for that]
Signed-off-by: Tom Rini <trini@ti.com>
move uart soft reset code to common place and call
this function from board code, instead of copy and paste
this code for every board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matt Porter <mporter@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Tom Rini <trini@ti.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Tom Rini <trini@ti.com>
[trini: Fix igep0033 build, remove 'regval' on pcm051]
Signed-off-by: Tom Rini <trini@ti.com>
move rtc32k_enable() to common place so all am33xx boards can use it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matt Porter <mporter@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Tom Rini <trini@ti.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Small conflict over DRA7XX updates and adding SRAM_SCRATCH_SPACE_ADDR
Conflicts:
arch/arm/include/asm/arch-omap5/omap.h
Signed-off-by: Tom Rini <trini@ti.com>
The omap2420H4 was the only mainline omap24xx board. Prior to being
fixed by Jon Hunter in time for v2013.04 it had been functionally broken
for a very long time. Remove this board as there's not been interest in
it in U-Boot for quite a long time.
Signed-off-by: Tom Rini <trini@ti.com>
After having the u-boot clean up series, there are
many definitions that are unused in header files.
Removing all those unused ones.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Jump into full u-boot mode if a 'c' character is received on the uart.
We need to adjust the spl bss/malloc area to not overlap with the
loadaddr of the kernel (sdram + 32k), so move it past u-boot instead.
For raw mmc, we store the kernel parameter area in the free space after
the MBR (if used). For nand, we use the last sector of the partition
reserved for u-boot.
This also enables the spl command in the full u-boot so the kernel
parameter area snapshot can be created.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
We need to call the save_omap_boot_params function on am33xx/ti81xx and
other newer TI SoCs, so move the function to boot-common. Only OMAP4+
has the omap_hw_init_context function so add ifdefs to not call it on
am33xx/ti81xx. Call save_omap_boot_params from s_init on am33xx/ti81xx
boards.
Reviewed-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Fix the device tree loading for panda(4430) and panda-es(4460)
Modify the board name if a 4460 panda or panda-es is detected
at run time.
In the findfdt add a check for the panda-es board name and load
the panda-es device tree blob.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
We are able to tell the difference between xM Rev Ax/Bx and xM Rev Cx,
and have been for some time. The comment above the function however did
not list this, so update.
Signed-off-by: Tom Rini <trini@ti.com>
Since TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs,
rename twl6035_init_settings with an more generic palmas_init_settings
Signed-off-by: Nishanth Menon <nm@ti.com>
TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs
Rename twl6035 to palmas to allow reuse across multiple current and
future platforms
As part of this change, change the CONFIG_TWL6035_POWER to
CONFIG_PALMAS_POWER and update usage of header file accordingly.
Signed-off-by: Nishanth Menon <nm@ti.com>
Adds CPSW support to the TI814X EVM configured with
an ET1011C PHY in GMII mode.
Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
In the current u-boot, the device pin multiplexing and clock
initialisation needs to be early during the boot process and before
board_init() is called. U-boot is currently crashing on this board
because this is not being done early enough. Therefore, add a s_init()
function for the omap5912-osk board to do this.
Also fix the stack pointer so that it is pointing to the end of the
internal RAM and not the beginning as this was also causing the device
to crash.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
The omap5912-osk board is using a RAM based address as the linker
location for code. This is causing several problems when attempting
to run the latest u-boot code base on this board from flash. Update
the default linker location for code to be in NOR flash at address
0x00000000.
The omap5912-osk board only has 32MB of RAM and so fix the comment
in the omap5912-osk config.mk file as well.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
The size of the DRAM for the omap5912-osk board is getting setup in the
dram_init() function. However, for the current u-boot release this is
too late and needs to be done in dram_init_banksize(). Therefore, add
a dram_init_banksize() function for the omap5912-osk board and setup the
DRAM size there.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
After further testing we can run DDR at 400MHz so update the timings
again.
Tested-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Tom Rini <trini@ti.com>
The omap5-uevm is the reference board name for OMAP5 soc
based platform. So rename it accordingly.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
The omap2420-h4 board is using a RAM based address as the linker
location for code. This is causing several problems when attempting
to run the latest u-boot code base on this board from flash. Update
the default linker location for code to be in NOR flash. Please note
that OMAP maps the NOR flash to address 0x08000000 by default and so
use this as the default address for the NOR flash.
Also remove legacy code that attempts to calculate where in flash the
sdata structure, that holds the memory interface configuration data,
is located. By changing the default linker location for code to flash
this is no longer necessary.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
The size of the DRAM for the omap2420-h4 board is getting setup in the
dram_init() function. However, for the current u-boot release this is
too late and needs to be done in dram_init_banksize(). Therefore, add
a dram_init_banksize() function for the omap2420-h4 board and setup the
DRAM size there.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
The AM33xx emif4/ddr support closely matches what is need to support
TI814x except that TI814x has two EMIF instances. Refactor all the
emif4 helper calls and the config_ddr() init function to use an
additional instance number argument.
Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Eliminate AM33xx specific names to prepare for TI814x support
within AM33xx-land.
Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Enable DDR PHY dynamic power down bit, which enables
powering down the IO receiver when not performing read.
This also helps in reducing overall power consumption in
low power states (suspend/standby).
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Satyanarayana, Sandhya <sandhya.satyanarayana@ti.com>
Cc: Tom Rini <trini@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Adding new board files for DRA7XX socs.
The pad registers layout is changed completely from OMAP5
So introducing the new structure here and also adding the
minimal data.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishant Kamat <nskamat@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
[trini: Adapt omap_mmc_init call for last 2 params]
Signed-off-by: Tom Rini <trini@ti.com>
Currently, omap3_dss_panel_config() sets gfx_format to a value that is hardcoded
in the code. This forces anyone who wants to use a different gfx_format to make
adjustments after calling omap3_dss_panel_config(). This could be avoided if the
value of gfx_format were parameterized as input for omap3_dss_panel_config().
Make gfx_format a field in struct panel_config, and update existing structs to
set this field to the value that was originally hard coded.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
We add USB (RNDIS gadget) SPL support as a separate target. We need to
pull out YMODEM support in order to be a small enough target binary.
Signed-off-by: Tom Rini <trini@ti.com>
This adds necessary config options and a new build target,
am335x_evm_usbspl, to enable usb booting and fixes board_eth_init()
function to take into account that we may have USB ether support in SPL
now. This uses the same MAC for both cpsw and USB, in order to match
ROM behavior.
The usbspl build target does not contain UART SPL, CPSW SPL or extra
environment settings, so that we may fit within our binary size
constraint.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Signed-off-by: Tom Rini <trini@ti.com>
In commit cfd4ff6 we implemented part of advisory 1.0.10 (internal delay
for RGMII mode not supported). This in turn however requires that we
set the tx clock delay feature in the PHY itself.
Signed-off-by: Tom Rini <trini@ti.com>
AM335x EVM 1.5A uses Micron MT41J512M8RH-125 SDRAM 4Gb (512Mx8) as the
DDR3 chip.
[Hebbar Gururaja <gururaja.hebbar@ti.com>]
- Resolve merge conflict while rebasing. File structure is
changed in the mainline. So re-arrange the code accordingly.
- Update commit message to reflect the DDR3 part number
Signed-off-by: Jeff Lance <j-lance1@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Hebbar Gururaja <gururaja.hebbar@ti.com>
When ethaddr is not set in environment the MAC address is read
from efuse. The message was only printed in debug case, but this
message could be of interest for the ordinary user, so printf it.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
According to errata the AM335x device does not support internal delay
mode, so RGMII1_IDMODE and RGMII2_IDMODE must be set to 1.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Instead of passing individual registers by value to board_get_mem_timings,
pass a board_mem_timings structure pointer for the board files to fill in.
Pass same structure pointer to write_sdrc_timings. This saves about
90 bytes of space in SPL.
Signed-off-by: Peter Barada <peter.barada@logicpd.com>
We add CONFIG_ENV_VARS_UBOOT_CONFIG,
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and CONFIG_BOARD_LATE_INIT to set
the variables and then fdtfile and findfdt to make us of this. It is
now possible to do 'run findfdt' to have fdtfile be set to the value of
the dtb file to load for the board we are running on.
Signed-off-by: Tom Rini <trini@ti.com>
This patch extends the am335x_evm board for the AM335x IDK.
The IDK board uses MII for the ethernet phy (same as
Beaglebone board) and MMC0 for storage (but without
card detect line).
The IDK uses UART3 for console. So u-boot must be build
with CONFIG_SERIAL4 and CONFIG_CONS_INDEX=4 or for
the am335x_evm_uart3 board configuration as introduced
by Andrew Bradfords recent patch series "am33xx: Enable
UART {1,2,3,4,5}...". When using the IDK with console on UART0,
those patches are not required. In this case the board
slightly needs to be modified.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
This fixes the following boothang in SPL:
Unknown board, cannot configure pinmux.### ERROR ### Please RESET the board ###
Future commits will add pinmuxes for more on-board peripherals.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
If configured to use UART{1,2,3,4,5} such as on the Beaglebone RS232
cape or on the am335x_evm daughterboard, enable the proper pin-muxing.
Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
Move the hardcoded ddr2/ddr3 settings for the ti boards to board code,
so other boards can use different types/timings.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
[trini: Make apply with rtc32k_enable() in the file]
Signed-off-by: Tom Rini <trini@ti.com>
The i2c header is specific to ti(-derived) boards, and not generic for all
am335x boards.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
[trini: Make re-apply with rtc32k_enable() applied]
Signed-off-by: Tom Rini <trini@ti.com>
Kill off ehci-core.h
It was used to specify some static controller data. To support more than
one controller being active at any time we have to carry the controller
data ourselfes. Change the ehci interface accordingly.
NOTE: OMAP implemented the ehci stuff a bit backwards and should be fixed
to do the same thing as other platforms. But the change for now is at least
compile clean.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Under option -munaligned-access, gcc can perform local char
or 16-bit array initializations using misaligned native
accesses which will throw a data abort exception. Fix files
where these array initializations were unneeded, and for
files known to contain such initializations, enforce gcc
option -mno-unaligned-access.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
[trini: Switch to usign call cc-option for -mno-unaligned-access as
Albert had done previously as that's really correct]
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds support for networking in SPL. Some devices are
capable of loading SPL via network so it makes sense to load the
main U-Boot binary via network too. This patch tries to use
existing network code as much as possible. Unfortunately, it depends
on environment which in turn depends on other code so SPL size
is increased significantly. No effort was done to decouple network
code and environment so far.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@ti.com>
The AM335x GP EVM can have one of 8 different profiles selected. Each
profile has a different set of peripherals and requires different pinmux
configurations that conflict with other profiles. i2c1 is an example of
a conflicted mux currently.
Signed-off-by: Tom Rini <trini@ti.com>
- Move definition of the EEPROM contents to <asm/arch/sys_proto.h>
- Make some defines a little less generic now.
- Pinmux must be done by done by SPL now.
- Create 3 pinmux functions, uart0, i2c0 and board.
- Add pinmux specific to Starter Kit EVM for MMC now.
Signed-off-by: Tom Rini <trini@ti.com>
- Board requires gpio0 #7 to be set to power DDR3.
- Board uses DDR3, add a way to determine which DDR type to call
config_ddr with.
- Both of the above require filling in the header structure early, move
it into the data section.
Signed-off-by: Tom Rini <trini@ti.com>
The intention has always been (and boards are to support) an i2c EEPROM
that will identify what hardware they are, allowing a single binary to
support multiple boards. As such, remove the 'evm.c' file as there is
nothing EVM centric in it currently, only SoC peripheral configuration.
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds board-specific initialization for CPSW on
TI AM335X based boards. Tested on BeagleBone.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
[Ilya: split board-specific part into separate patch]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Read the on-board EEPROM during startup to detect the version
of the board we are running on (as for now only BeagleBone vs
EVM detection is supported).
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
This patch adds pin mux settings for CPSW switch found on
TI AM335X based boards (MII and RGMII modes).
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
[Ilya: split pinmux into separate patch]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
UART_RESET, UART_CLK_RUNNING_MASK, and UART_SMART_IDLE_EN
are defined inn evm.c but not used. Also removes unnecessary
include of serial.h
PHYS_DRAM_1_SIZE is defined in am335x_evm.h but never used.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
* 'next' of git://git.denx.de/u-boot:
MPC8xx: Fixup warning in arch/powerpc/cpu/mpc8xx/cpu.c
doc: cleanup - move board READMEs into respective board directories
net: sh_eth: add support for SH7757's GETHER
net: sh_eth: modify the definitions of regsiter
net: sh_eth: add SH_ETH_TYPE_ condition
net: sh_eth: clean up for the SH7757's code
net: fec_mxc: Fix MDC for xMII
net: fec_mxc: Fix setting of RCR for xMII
net: nfs: make NFS_TIMEOUT configurable
net: Inline the new eth_setenv_enetaddr_by_index function
net: allow setting env enetaddr from net device setting
net/designware: Consecutive writes to the same register to be avoided
CACHE: net: asix: Fix asix driver to work with data cache on
net: phy: micrel: make ksz9021 phy accessible
net: abort network initialization if the PHY driver fails
phylib: phy_startup() should return an error code on failure
net: tftp: fix type of block arg to store_block
Signed-off-by: Wolfgang Denk <wd@denx.de>
Also drop a few files referring to no longer / not yet supported
boards.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Jason Jin <jason.jin@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
In commit 1a89a217f5 we moved most of the
required pads and mux data for USB to the essential list so that later
on we could NOT enable anything that wasn't essential unless otherwise
configured. This was however missing a few pandaboard-specific parts
which left for example USB ethernet non-functional.
Tested this on OMAP4430 ES2.2, OMAP4460 ES1.1 PANDA boards.
(Reworded by Tom Rini to be more precise about what the problem was)
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Tested-by: Gary Thomas <gary@mlbassoc.com>
Tested-by: Tom Rini <trini@ti.com>
USB module pads are getting enabled under non-essential
group. These will be required for fastboot, tftp support.
So move this to essential list to have them working when
non-essential pads are no more muxed.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
If uart2 is enabled during boot, spurious wifi chip transmission will
hang the module and it is impossible to recover from this situation
without hard reset. This will prevent any l4_per domain idle
transitions.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
TPS SET0/SET1 register is selected by a GPIO pin on OMAP4460 platforms.
Currently we control this pin with a mux configuration as part of
boot sequence.
Current configuration results in the following voltage waveform:
|---------------| (SET1 default 1.4V)
| --------(programmed voltage)
| <- (This switch happens on mux7,pullup)
vdd_mpu(TPS) -----/ (OPP boot voltage)
--------- (programmed voltage)
vdd_core(TWL6030) -----------------------/ (OPP boot voltage)
Problem 1) |<----- Tx ------>|
timing violation for a duration Tx close to few milliseconds.
Problem 2) voltage of MPU goes beyond spec for even the highest of MPU OPP.
By using GPIO as recommended as standard procedure by TI, the sequence
changes to:
-------- (programmed voltage)
vdd_mpu(TPS) ------------/ (Opp boot voltage)
--------- (programmed voltage)
vdd_core(TWL6030) -------------/ (OPP boot voltage)
NOTE: This does not attempt to address OMAP5 - Aneesh please confirm
Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Add parameters to the OMAP MMC initialization function so the board can
mask host capabilities and set the maximum clock frequency. While the
OMAP supports a certain set of MMC host capabilities, individual boards
may be more restricted and the OMAP may need to be configured to match
the board. The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example.
Signed-off-by: Jonathan Solnit <jsolnit@gmail.com>
Remove userbutton command and do the detection in board config file using the gpio command
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
The CS_AUTOBOOT configurations have been broken for a long time.
Kshitij Gupta is no longer at TI making these broken and orphaned
boards, so remove.
Signed-off-by: Tom Rini <trini@ti.com>
Fix:
beagle.c:257:13: warning: function declaration isn't a prototype
[-Wstrict-prototypes]
beagle.c:257:13: warning: function declaration isn't a prototype
[-Wstrict-prototypes]
Also make beagle_dvi_pup() checkpatch clean, fix:
ERROR: open brace '{' following function declarations go on the
next line
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Tom Rini <trini@ti.com>
This changes the number 15 as used in boot_stage_progress() to use the
new name provided for it. This is a separate patch because it touches
so many files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
this patch addresses the issue that there is no DVI output on beagleboard-xm in
u-boot; the TFP410 is not powered on, DVI_PUP needs to be set high
this is done differently on beagleboard-xm rev. B/C versus earlier boards:
beagleboard-xm B/C need to set GPIO2 of the TWL4030
earlier boards need to set GPIO170
note that the change occured somewhere inbetween beagleboard-xm rev. A2 and A3
note that beagleboard-xm rev. A and rev. B cannot be distinguished using
get_board_revision(), REVISION_XM_A/REVISION_XM_B is bogus
due to this glitch, the patch cannot work correctly on some beagleboard-xm
rev A/B boards
tested on beagleboard-xm rev. C (you should see orange color on a monitor)
note that the framebuffer is NOT yet set up, this could be done along the
lines below (for 800x480 resolution and RGB24) before calling omap3_dss_enable()
static void configure_frame_buffer() {
writel(0x80500000, (uint *) 0x48050480); // address
writel(0x80500000, (uint *) 0x48050484);
writel(0x01df031f, (uint *) 0x4805048c); // size
writel(0x00000091, (uint *) 0x480504a0); // RGB24
}
Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
For panda initialise the mux pins for ehci usage and
enable ehci in omap4_panda config file.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Clean up added ehci-omap.c and make it generic for re-use across
omap-soc having same ehci ip block. Also pass the modes to be configured
from board file and configure the ports accordingly. All usb layers
are not cache aligned, till then keep cache off for usb ops as ehci will use
internally dma for all usb ops.
* Add a generic common header ehci-omap.h having common ip block
data and reg shifts.
* Rename and modify ehci-omap3 to ehci.h retain only conflicting
sysc reg shifts remove others and move to common header file.
* pass the board data for beagle/panda accordinly to use
ehci ports.
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
The logic for the rev C4 boards was missing one of the cases
(variant with Micron NAND and 2x128MB).
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
This patch is added to support SPL feature on AM335X
platform. In this patch, MMC1 is configured as boot
device for SPL and support for other devices will be
added in the next patch series.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
This patch add supports for mmc/sd driver on AM335X platform.
PLL and pinmux configurations for mmc/sd are configured in this
patch.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
During misc_init_r, make sure to setup the clocks
properly for the USB hub on the pandaboard. With
this in place, the USB hub and the ethernet works
on the pandaboard.
Signed-off-by: Chris Lalancette <clalancette@gmail.com>
Acked-by: Aneesh V <aneesh@ti.com>
Fix:
omap2420h4.c: In function 'dram_init':
omap2420h4.c:196:25: warning: variable 'cpu' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Tom Rini <trini@ti.com>
Fix:
flash.c: In function 'flash_get_offsets':
flash.c:122:10: warning: variable 'pOrgDef' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'flash_erase':
flash.c:263:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'write_data':
flash.c:439:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Dave Peverley <dpeverley@mpc-data.co.uk>
Acked-by: Tom Rini <trini@ti.com>
Fix:
flash.c: In function 'flash_get_offsets':
flash.c:139:10: warning: variable 'pOrgDef' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'flash_erase':
flash.c:280:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'write_data':
flash.c:456:6: warning: variable 'flag' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Tom Rini <trini@ti.com>
The only change of note is that we move from 0x80008000 to 0x80100000
for CONFIG_SYS_TEXT_BASE
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Tested-by: Koen Kooi <k-kooi@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Add Hynix 200MHz timing information to <asm/arch-omap3/mem.h>.
This also changes CONFIG_SYS_TEXT_BASE to 0x80100000.
Signed-off-by: Tom Rini <trini@ti.com>
This introduces 200MHz Micron parts timing information based on x-loader
to <asm/arch-omap3/mem.h> and Numonyx MCFG calculation. The memory init
logic is also based on what x-loader does in these cases. Note that
while previously u-boot would be flashed in with SW ECC in this case it
now must be flashed with HW ECC. We also change CONFIG_SYS_TEXT_BASE to
0x80100000.
Cc: Dirk Behme <dirk.behme@gmail.com>
Beagleboard rev C5, xM rev A:
Tested-by: Tom Rini <trini@ti.com>
Beagleboard xM rev C:
Tested-by: Matt Ranostay <mranostay@gmail.com>
Beagleboard rev B7, C2, xM rev B:
Tested-by: Matt Porter <mporter@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
TPS power IC is controlled using a GPIO (gpio_wk7).
This GPIO should be maintained at logic 1 always. As
such an internal pull-up on this pin will do the job,
driving the GPIO outuput is not needed. This will avoid
the need of using GPIO library in SPL and also may
save some power.
Signed-off-by: Aneesh V <aneesh@ti.com>
Configuration header(CH) is 512 byte header attached to an OMAP
boot image that will help ROM code to initialize clocks, SDRAM
etc and copy U-Boot directly into SDRAM. CH can help us in
by-passing SPL and directly boot U-boot, hence it's an alternative
for SPL. However, we intend to support both CH and SPL for OMAP4/5.
Initialization done through CH is limited and is not equivalent
to that done by SPL. So U-Boot has to distinguish between the
two cases and handle them accordingly. This patch takes care
of doing this.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds the minimal support for OMAP5. The platform and machine
specific headers and sources updated for OMAP5430.
OMAP5430 is Texas Instrument's SOC based on ARM Cortex-A15 SMP architecture.
It's a dual core SOC with GIC used for interrupt handling and SCU for cache
coherency.
Also moved some part of code from the basic platform support that can be made
common for OMAP4/5. Rest is kept out seperately. The same approach is followed
for clocks and emif support in the subsequent patches.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
It is now responsibility of the board specific init
code to set the environment variable corresponding
to the MAC address.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds basic support for booting the board.
This patch adds support for the UART necessary to
get to the u-boot prompt.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
gpio_free() should not have the side effect of setting the line to input since this prevents the gpio command from being able to set a line as output.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Not all padconfs are the same between 4430 and 4460, so instead of
working around this with an if, we should have an specific padconf
structure for both chips (like handling the differences between the LEDs
GPIOs and TPS).
Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The top level Makefile does not do any recursion into subdirs when
cleaning, so these clean/distclean targets in random arch/board dirs
never get used. Punt them all.
MAKEALL didn't report any errors related to this that I could see.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Result of running the following command to address Wolfgang's
comment about camel case:
for file in `find . | grep '\.[chS]$'`; do perl -i -pe
's/(green|yellow|red|blue)_LED_(on|off)/$1_led_$2/g' $file; done
Discussion:
http://patchwork.ozlabs.org/patch/84988/
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
omap4: fix pad configuration settings for SDP and Panda
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sebastien Jan <s-jan@ti.com>
Signed-off-by: David Anders <x0132446@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* Read the led output state from GPIO instead saving state in memory when it is [re]set
* Added a toggle option to the led command
Previous discussion:
http://lists.denx.de/pipermail/u-boot/2011-May/093068.html
Changes since v1:
Fixed checkpatch errors
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Fixed USR0/USR1 to be LED 0/1 respectively
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Based on patches from Syed Mohammed Khasim (khasim@ti.com).
Configures the output of the BeagleBoard DVI to be orange.
Configures the output of the BeagleBoard S-Video to be a colorbar.
Changed display_init to beagle_display_init as suggested by Igor Grinberg:
http://www.mail-archive.com/u-boot@lists.denx.de/msg51446.html
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Based on commit f1099c7c43caf5bac3bf6a65aa266fade4747072
Author: Greg Turner <gregturner@ti.com>
Date: Tue May 25 09:19:06 2010 -0500
New u-boot command for status of USER button on BeagleBoard-xM
Modified bootcmd to check the staus at boot time and set
filename of the boot script.
* Moved to a BeagleBoard specific file.
* Removed changes to default boot command from adding userbutton
command.
* Made to handle pre-xM boards.
* Flipped polarity of the return value to avoid confusion. Success (0)
is when the button is pressed. Failure (1) is when the button is NOT
pressed.
* Used latest revision getting function.
* Used latest macros for board revision.
* Added xM-C revision definition (optional, since it was default)
* updated default configuration with UserButton functionality
* Added a separate bootenv variable to load a user defined .txt file
* Added an example, showing how a different environment file can be loaded with
the user button pressed
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Cc: Greg Turner <gregturner@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This fixes display problems in linux
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The below patch reverses the order of two segments in the board file.
Output pins need to have their values initialized, before they are
exposed to the logic outside the chip.
Signed-off-by: Bob Feretich <bob.feretich@rafresearch.com>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver. This patch is based on the work done for Beagle, etc.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver. This patch is based on the work done for Beagle, etc.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Switch from the legacy mmc driver to the
new generic mmc driver.
This patch is based on similar patch for beagle[1].
[1] http://git.denx.de/?p=u-boot.git;a=commitdiff_plain;h=0cd31144240
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Innovator and H2 boards used machine_is_* macros for setting the machine
type. These macros are expanded in compile time and thus leaves
unreachable code (though gcc might optimize it).
Switch them to use common code for machine type setting.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
- Provide alternate implementations of board_init_f()
board_init_r() for OMAP spl.
- Provide linker script
- Initialize global data
- Add serial console support
- Update CONFIG_SYS_TEXT_BASE to allow for SPL's bss and move
it to board config header from config.mk
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
- separate mux settings into essential and non essential parts
- essential part is board independent as of now(so move it
to SoC directory). Will help in having single SPL for all
boards.
- Non-essential part(the pins not essential for u-boot to function)
need to be phased out eventually.
- Correct mux data by aligning to the latest settings in x-loader
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
These functions are not required when CONFIG_CMD_NET
is not defined:
- setup_net_chip()
- reset_net_chip()
- board_eth_init()
This patch wraps them in #ifdef CONFIG_CMD_NET...#endif
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The GPIO pin used for resetting the external LAN chip has
changed for Rev.G board.
The patch uses generic gpio API instead of direct access
to corresponding registers.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
In current implementation, the function sets up the ethernet
chip and resets it. The steps to reset depend upon the board
revision.
The patch moves the reset actions to new function reset_net_chip().
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
A large number of boards incorrectly used getenv() in their board init
code running before relocation. In some cases this caused U-Boot to
hang when certain environment variables grew too long.
Fix the code to use getenv_r().
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: The LEOX team <team@leox.org>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Georg Schardt <schardt@team-ctech.de>
Cc: Werner Pfister <Pfister_Werner@intercontrol.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Peter De Schrijver <p2@mind.be>
Cc: John Zhan <zhanz@sinovee.com>
Cc: Rishi Bhattacharya <rishi@ti.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
The reset sequence/configuration for ehci is highly board specific,
so this will be done in the source for the board, instead of
introducing several CONFIG_* which would be needed to make those
few lines in beagle.c usable across different OMAP boards.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
It is a low cost reference design based on Sitara AM3517 SoC from Texas Instruments
Please refer to <www.craneboard.org> for more details.
Signed-off-by: Srinath <srinath@mistralsolutions.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Patch was updated by Jason Kridner <jkridner@beagleboard.org>:
* Use tabs to match style of other board revisions
* Only include board revisions that exist
* Default to the same configuration as the latest revision, but
without setting 'beaglerev'
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This allows the reading of EEPROMS on the expansion bus without adding
external pull-ups.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Added LED driver using status_led. USR0 is set to monitor the boot
status. USR1 is set to be the green LED.
Included adding configuration and command to the default configuration.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
It can be optimised out by the compiler otherwise resulting
in obscure errors like a board not booting.
This has been documented in README since 2006 when these were
first fixed up for GCC 4.x.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Fix some additional places.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-By: Albert ARIBAUD <albert.aribaud@free.fr>
Convert the variable omap3_evm_version to u32 to work around
some broken linkers from older tool chains. E.g. CodeSourcery's
2009q1-203 ld 2.19.51.20090205. Without this, these linkers
stop linking 'omap3_evm' or at least issue a warning. Like
arm-none-linux-gnueabi-ld: section .bss [8003f5e0 -> 8007e337] overlaps section .rel.dyn [8003f5e0 -> 80044e57]
arm-none-linux-gnueabi-ld: section .dynsym [80044e58 -> 80044ef7] overlaps section.bss [8003f5e0 -> 8007e337]
arm-none-linux-gnueabi-ld: u-boot: section .bss vma 0x8003f5e0 overlaps previous sections
CC: Sanjeev Premi <premi@ti.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Add battery charging support twl6030 driver.
Add support for battery voltage and current measurements.
Add command to get battery status and start/stop battery charging from USB.
Signed-off-by: Balaji T K <balajitk@ti.com>
Tested-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
Function omap3_evm_get_revision() - to identify the
board revision was called at end of setup_net_chip().
Board revision can be ascertained only by identifying
the Ethernet chipset - but combining setup operations
with revision detection isn't a good idea. So, moved
the function after call to setup_net_chip().
Function setup_net_chip() should be ideally be called
only when CONFIG_CMD_NET is defined. But this leaves
the board revision "undetected". This patch allows
static definition of revision or default fallback to
the latest revision.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The function omap3_evm_need_extvbus() is required
only when USB support is configured.
Wrapped this function in #ifdef CONFIG_USB_OMAP3.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds relocation support for omap3evm.
Content of the patch is based on changes for
Beagleboard.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Beagle expansion boards contain an i2c eeprom to identify themselves.
This patch adds code to read and parse the eeprom contents. It prints
the expansion board name and revision and modifies environment variables
as appropriate. This patch is based on the Overo expansion board code.
Signed-off-by: Koen Kooi <k-kooi@ti.com>
Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.
Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch switches from the legacy mmc driver to the new generic mmc driver
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
This patch switches from the legacy mmc driver to the new generic mmc driver
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
This patch adds missing pinmux setup for 4 GPIO signals used on the Beagle xM:
- USB hub reset (gpio_56)
- P8 USB hub reset (gpio_63)
- DVI enable (gpio_129)
- P8 DVI enable (gpio_170)
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch corrects the pinmux settings to enable proper functioning
of the wifi/bluetooth module.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Change the implementation for ARM V7 to relocate the code to an
arbitrary address in RAM.
Adapt the Beagle board (Cortex A8) to test the changes.
Portions of this work were supported by funding from
the CE Linux Forum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Correctly set PAD1_FREF_CLK4_REQ and PAD0_FREF_CLK4_OUT to enable and
activate both LEDs while setting pad mux.
Since this increases the line length, this patch also adjusts the white
space in this section of code to allign the pad mux signal description
comments.
Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@canonical.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds support for the Beagle xM. It uses the board ID
GPIO bits to recognize this revision and perform appropriate setup.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch enhances the revision detection function and adds
support for the C4 revision. The board revision is printed
and approriate revision specific setup is done automatically.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Add functional multiplexing support for OMAP4 pads.
Configure all the pads for the OMAP4430 SDP
and OMAP4 Panda boards
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds a gpmc_init function for OMAP4 and adds calls to
gpmc_init for existing OMAP4 boards: panda and sdp4430
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
OMAP4 Panda is a reference board based on OMAP4430, an ARMV7 Cortex A9 CPU
This patch adds basic support for booting the board. It includes i2c and mmc
support. It assumes U-boot is loaded to SDRAM with the help of another small
bootloader (x-load) running from SRAM. U-boot currently relies on x-load for
clock, mux, and SDRAM initialization
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
OMAP4430 SDP is a reference board based on OMAP4430, an ARMV7 Cortex A9 CPU
This patch adds basic support for booting the board. It includes i2c and mmc
support. It assumes U-boot is loaded to SDRAM with the help of another small
bootloader (x-load) running from SRAM. U-boot currently relies on x-load for
clock, mux, and SDRAM initialization
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Added function to differentiate between the OMAP3EVM revisions. The
chip-id of the ethernet PHY is being used for this purpose.
Rev A to D : 0x01150000
Rev >= E : 0x92200000
CC: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Sandeep Paulraj <s-paulraj@ti.com>
TNETV107X is a Texas Instruments SoC based on an ARM1176 core, and with a
bunch on on-chip integrated peripherals. This patch adds support for the
TNETV107X EVM board.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Not all boards have both LEDs hooked, so enabling both on
boards with single LED will just waste power. Make it
possible to choose LEDs by adding argument to
twl4030_led_init().
Using this turn on only LEDB for pandora, leave both LEDs
on for all other boards, as it was before this patch.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
A previous Commit converted the LAN91C96 Ethernet driver to using the
CONFIG_NET_MULTI API, but did not include full board support. This patch
finishes the job.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Enable the NET MULTI option and remove build warning
Tested: SDP3430
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Start of support of
Texas Instruments Software Development Platform(SDP)
for OMAP3430 - SDP3430
Highlights of this platform are:
Flash Memory devices:
Sibley NOR, Micron 8bit NAND and OneNAND
Connectivity:
3 UARTs and expanded 4 UART ports + IrDA
Ethernet, USB
Other peripherals:
TWL5030 PMIC+Audio+Keypad
VGA display
Expansion ports:
Memory devices plugin boards (PISMO)
Connectivity board for GPS,WLAN etc.
Completely configurable boot sequence and device mapping
etc.
Support default jumpering and:
- UART1/ttyS0 console(legacy sdp3430 u-boot)
- UART3/ttyS2 console (matching other boards,
and SDP HW docs)
- Ethernet
- mmc0
- NOR boot
Currently the UART1 is enabled by default. for
compatibility with other OMAP3 u-boot platforms,
enable the #define of CONSOLE_J9.
Conflicts:
Makefile
Fixed the conflict with smdkc100_config by moving omap_sdp3430_config
to it is alphabetically sorted location above zoom1.
Signed-off-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Switch from space-based indentation to tab-based in mux configs, as pointed
out by WD at:
http://lists.denx.de/pipermail/u-boot/2009-September/061241.html
Nothing but whitespace changes in this patch (diff -w gives no output).
Signed-off-by: Olof Johansson <olof@lixom.net>
