LS2085A supports 6 personalities i.e. LS2045AE, LS2045A, LS2080AE,
LS2080A, LS2085AE and LS2085A personlities.
Instead of hard-coding, board name should change as per selected
personality.
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As per updated board document, no need to substract 1 from arch[BRD]
bit field. Default value + 'A' represents the board revision.
So update board version print logic to reflect the same.
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SYSTEM ID EPPROM always store SYSTEM version info in big endian format.
SoC with ARM or PowerPC core should read/write version info from eeprom
in BIG endian format.
So use cpu-specific APIs to read SYSTEM version.
Signed-off-by: Jaiprakash Singh <b44839 at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
FPGA BRDCFG9[SFP_TX] should be clear in order to enable XFI ports.
Signed-off-by: Dai Haruki <Dai.Haruki at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SerDes Protocol 0x49 enables 4 SGMII, PEX4, SATA1 and SATA2.
Add support of 0x49 SerDes protocol to enable 4SGMII on slot4 of
ls2085aqds platform.
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add hwconfig setting for eSDHC since it shares some pins with other
IP block.
Signed-off-by: Yangbo Lu <yangbo.lu at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support for board eth initialization and support for loading phy
firmware. PHY firmware needs to be loaded from board_eth_init() because
all the MACs are not initialized by ldpaa_eth driver.
Signed-off-by: pankaj chauhan <pankaj.chauhan at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
ccsr_ddr structure is already defined in fsl_immap.h. Remove
this duplicated define. Move fixed timing into ls1021atwr.h.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alison Wang <alison.wang@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
CONFIG_ARMV7_VIRT depends on CONFIG_ARMV7_NONSEC, thus doesn't need to
be taken into account additionally. CONFIG_ARMV7_PSCI is only set on
boards that support CONFIG_ARMV7_NONSEC, and it only works on those.
CC: Tang Yuantian <Yuantian.Tang@freescale.com>
CC: York Sun <yorksun@freescale.com>
CC: Steve Rae <srae@broadcom.com>
CC: Andre Przywara <andre.przywara@linaro.org>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
1. board/freescale/t4qds/t4_rcw.cfg
1.8GHz support is requested as default frequency, so update the rcw.
2. remove un-used configs
configs/T4160QDS_SPIFLASH_defconfig
configs/T4240QDS_SPIFLASH_defconfig
SPI boot is not available on T4QDS, so the configs should be removed.
3. board/freescale/t4qds/MAINTAINERS
Updated MAINTAINERS accordingly.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
[York Sun: revise subject]
Reviewed-by: York Sun <yorksun@freescale.com>
T2080RDB RevC uses new SODIMM 1867MT/s instead of previous 1600MT/s.
So update RCW to support new DDR frequency 1867MT/s by default.
Reserve the old 1600MT/s in comment for users in needed.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add adapter card type identification support by reading
FPGA STAT_PRES1 register SDHC Card ID[0:2] bits. To use this function,
define CONFIG_FSL_ESDHC_ADAPTER_IDENT.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
[York Sun: resolve conflicts in README.fsl-esdhc]
Reviewed-by: York Sun <yorksun@freescale.com>
CS4315 PHY doesn't support phy-reset by software, it
needs to reset it by hardware via CPLD control.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Function dp_ddr_restore is to restore the first 128-byte space
of DDR. However those codes may be optimized out by compiler
since the destination address is at 0x0. In order to avoid
compiler optimization, we restore the space from high address,
which is not at 0x0, to low address.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Use fdt_setprop_string instead of fdt_setprop to fix string length.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1023RDB is a Freescale Reference Design Board that hosts the T1023 SoC.
T1023RDB board Overview
-----------------------
- T1023 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- Memory: 2GB Micron MT40A512M8HX unbuffered 32-bit fixed DDR4 without ECC
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- one 1G RGMII port on-board(RTL8211F PHY)
- one 1G SGMII port on-board(RTL8211F PHY)
- one 2.5G SGMII port on-board(AQR105 PHY)
- PCIe: Two Mini-PCIe connectors on-board.
- SerDes: 4 lanes up to 10.3125GHz
- NOR: 128MB S29GL01GS110TFIV10 Spansion NOR Flash
- NAND: 512MB S34MS04G200BFI000 Spansion NAND Flash
- eSPI: 64MB S25FL512SAGMFI010 Spansion SPI flash.
- USB: one Type-A USB 2.0 port with internal PHY
- eSDHC: support SD/MMC card and eMMC on-board
- 256Kbit M24256 I2C EEPROM
- RTC: Real-time clock DS1339 on I2C bus
- UART: one serial port on-board with RJ45 connector
- Debugging: JTAG/COP for T1023 debugging
As well updated T1024RDB to add T1023RDB.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix defconfig files]
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds SD boot support for T4240RDB board. SPL
framework is used. PBL initializes the internal RAM and
copies SPL to it. Then SPL initializes DDR using SPD and
copies u-boot from SD card to DDR, finally SPL transfers
control to u-boot.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: Fix T4240RDB_SDCARD_defcofig]
Reviewed-by: York Sun <yorksun@freescale.com>
Enable NAND boot support using SPL framework. To boot from
NAND, either use DIP switches on board, or "qixis_reset nand"
command. Details of forming NAND image can be found in README.
Signed-off-by: Scott Wood <scottwood@freescale.com>
[York Sun: Remove +S from defconfig after commit 252ed872]
Signed-off-by: York Sun <yorksun@freescale.com>
Use "qixis_reset nand" to reset the board to boot from NAND.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
This adds NAND boot support for LS2085AQDS, using SPL framework.
Details of forming NAND image can be found in README.
Signed-off-by: Scott Wood <scottwood@freescale.com>
[York Sun: Remove +S from defconfig after commit 252ed872]
Signed-off-by: York Sun <yorksun@freescale.com>
IFC has two register pages.Till IFC version 1.4 each
register page is 4KB each.But IFC ver 2.0 register page
size is 64KB each.IFC regiters structure is break into
two viz FCM and RUNTIME.FCM(Flash control machine) registers
are defined in PAGE0 and controls IFC generic functionality.
RUNTIME registers are defined in PAGE1 and controls NAND and
GPCM funcinality.
FCM and RUNTIME structures defination is common for IFC
version 1.4 and 2.0.
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Add support of ethernet:
- eth.c: mapping lane to slot for (0x2A, 0x07)
- ls2085a.c: To enable/disable dpmac and get link type
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Enable the SCSC (Slow Clock Source Controller) and select the external
32KHz oscillator. This improves the accuracy of the RTC.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
In order to avoid code duplication, move the DDR3 initialization to the
common place under imx-common. Currently ROW_DIFF and COL_DIFF can be
chosen from the board file. The JEDEC timings are specified using a
common ddr3_jedec_timings structure.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Add architecture-specific u-boot.lds and remove all board-specific
u-boot.lds.
All the .text customization that was board-specific have been
moved inside the related include/configs, inside a
LDS_BOARD_TEXT define.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
The LS2085ARDB is a evaluation platform that supports LS2085A
family SoCs. This patch add sbasic support for the platform.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The LS2085AQDS is an evaluatoin platform that supports the LS2085A
family SoCs. This patch add basic support of the platform.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Add support for reset_cpu() by asserting RESET_REQ_B.
Signed-off-by: pankaj chauhan <pankaj.chauhan@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
The timer clock is system clock divided by 4, not fixed 12MHz.
This is common to the SoC, not board specific. Primary core is
fixed when u-boot still runs in board_f. Secondary cores are
fixed by reading a variable set by u-boot.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Mark Rutland <mark.rutland@arm.com>
mx6sabresd has four MT41K128M16JT-125 chips. Each memory has 16-bit bus
and 2GiB, so fix the width and density fields accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Move the compilation of file fsl_validate.c in MACRO CONFIG_CMD_ESBC_VALIDATE.
This file should be compiled only when the above MACRO is defined
This caused a break in compilation of iMX platforms when compiling for SECURE_BOOT
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Freescale's Layerscape Management Complex (MC) provide support various
objects like DPRC, DPNI, DPBP and DPIO.
Where:
DPRC: Place holdes for other MC objectes like DPNI, DPBP, DPIO
DPBP: Management of buffer pool
DPIO: Used for used to QBMan portal
DPNI: Represents standard network interface
These objects are used for DPAA ethernet drivers.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Geoff Thorpe <Geoff.Thorpe@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Cristian Sovaiala <cristian.sovaiala@freescale.com>
Signed-off-by: pankaj chauhan <pankaj.chauhan@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The Debug Server driver is responsible for loading the Debug
server FW on the Service Processor (Cortex-A5 core) on LS2085A like
SoCs and then polling for the successful initialization of the same.
TOP MEM HIDE is adjusted to ensure the space required by Debug Server
FW is accounted for. MC uses the DDR area which is calculated as:
MC DDR region start = Top of DDR - area reserved by Debug Server FW
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Muram will power off during deepsleep, and the microcode of qe
in muram will be lost, it should be reload when resume.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Muram will power off during deepsleep, and the microcode of qe
in muram will be lost, it should be reload when resume.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The patch uses the common function name ft_pci_setup to replace
ft_pcie_setup, then removes unnecessary pcie_layerscape.h because
all the functions have been declared in common.h.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1. Default environment will be used for secure boot flow
which can't be edited or saved.
2. Command for secure boot is predefined in the default
environment which will run on autoboot (and autoboot is
the only option allowed in case of secure boot) and it
looks like this:
#define CONFIG_SECBOOT \
"setenv bs_hdraddr 0xe8e00000;" \
"esbc_validate $bs_hdraddr;" \
"source $img_addr;" \
"esbc_halt;"
#endif
3. Boot Script can contain esbc_validate commands and bootm command.
Uboot source command used in default secure boot command will
run the bootscript.
4. Command esbc_halt added to ensure either bootm executes
after validation of images or core should just spin.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
On QDS board with DDR4 DIMM, LPUART is used as console
output to verify DCU driver. This patch adds
ls1021aqds_ddr4_nor_lpuart_defconfig for this support.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale LS1021ATWR share some pins. Hwconfig option is used to
allows users to choose the pin functions.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
[York Sun: revised commit message]
Reviewed-by: York Sun <yorksun@freescale.com>
For LS102xA, some workarounds are only used in VER1.0, so silicon
version detection are added for QDS and TWR boards.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Support SODIMM D3XP12081XL10AA 1866MT/s on T2080RDB.
Enable CONFIG_CMD_MEMTEST as well.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory.
These values define the voltage requirements for
the chip. u-boot reads FUSESR and translates the values
into the appropriate commands to set the voltage output
value of an external voltage regulator.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Since commit 32df39c741 ("mx5: fix get_reset_cause") we have the following
boot messages on a mx53qsb:
U-Boot 2015.04-rc5-00029-gd68df02 (Apr 06 2015 - 11:15:39)
CPU: Freescale i.MX53 rev2.1 at 800 MHz
Reset cause: POR
Board: MX53 LOCO
I2C: ready
DRAM: 1 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
CPU: Freescale i.MX53 rev2.1 at 1000 MHz
Reset cause: unknown reset
Net: FEC [PRIME]
The CPU and Reset cause lines appear twice.
Initially mx53 boots at 800MHz, then at a later point the PMIC is configured via
I2C to raise the CPU voltage so that it can run at 1GHz.
To avoid such misleading double printings, disable printing cpu info for now.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
Fix eb_cpu5282 and eb_cpu5282_internal unresolved external error.
These boards have video but don't need any ppc related
video_setmem().
Fix M53017EVB moving away embedded env to a different offset,
as in M52277EVB.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
esbc_validate command uses various IP Blocks: Security Monitor, CAAM block
and SFP registers. Hence the respective CONFIG's are enabled.
Apart from these CONFIG_SHA_PROG_HW_ACCEL and CONFIG_RSA are also enabled.
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1. esbc_validate command is meant for validating header and
signature of images (Boot Script and ESBC uboot client).
SHA-256 and RSA operations are performed using SEC block in HW.
This command works on both PBL based and Non PBL based Freescale
platforms.
Command usage:
esbc_validate img_hdr_addr [pub_key_hash]
2. ESBC uboot client can be linux. Additionally, rootfs and device
tree blob can also be signed.
3. In the event of header or signature failure in validation,
ITS and ITF bits determine further course of action.
4. In case of soft failure, appropriate error is dumped on console.
5. In case of hard failure, SoC is issued RESET REQUEST after
dumping error on the console.
6. KEY REVOCATION Feature:
QorIQ platforms like B4/T4 have support of srk key table and key
revocation in ISBC code in Silicon.
The srk key table allows the user to have a key table with multiple
keys and revoke any key in case of particular key gets compromised.
In case the ISBC code uses the key revocation and srk key table to
verify the u-boot code, the subsequent chain of trust should also
use the same.
6. ISBC KEY EXTENSION Feature:
This feature allows large number of keys to be used for esbc validation
of images. A set of public keys is being signed and validated by ISBC
which can be further used for esbc validation of images.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This board uses DDR DIMM. Reading SPD provides more flexibility.
Raw timing parameter code should be removed after debugging.
Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
commit d9f43c8f5c sets
get_reset_cause() as static, but this conflicts with mx5
where its prototype is in sys_proto.h.
Drop it from sys_proto.h and drop print_cpuinfo from mx53_loco,
factorizing the call for this board.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Jason Liu <jason.hui@linaro.org>
Pass the same pad configuration as done in the kernel so that OTG1_ID pin can
properly work in device mode.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Currently there is no support for MC34704 PMIC in the mainline kernel.
Turn on the LCD supply via bootloader for the time being, so that we could
use the LCD in the kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
There 4 JRs, 4 RTICs and 8 DECOs, and set them the same stream id
for using the same SMMU3 on LS1021A.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Upgrade Manage Complex (MC) flib API to 0.5.2. Rename directory
fsl_mc to fsl-mc. Change the fsl-mc node in Linux device tree
from "fsl,dprcr" to "fsl-mc". Print MC version info when
appropriate.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LS2085A and its variants can have up to four clusters. It is safe
to enable timebase for all even some may be disabled.
Signed-off-by: York Sun <yorksun@freescale.com>
To normal mode, use APS switching mode.
To standy mode, use PFM switching mode.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
This patch is to implement pmic_mode_init function, and add prototype
in header file.
This function is to set switching mode for pmic buck regulators to
improve system efficiency.
Mode:
OFF: The regulator is switched off and the output voltage is discharged.
PFM: In this mode, the regulator is always in PFM mode, which
is useful at light loads for optimized efficiency.
PWM: In this mode, the regulator is always in PWM mode operation
regardless of load conditions.
APS: In this mode, the regulator moves automatically between
pulse skipping mode and PWM mode depending on load conditions.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Currently by running the following test:
=> setenv bootcmd reset
=> save
=> reset
, we observe a hang after approximately 20-30 minutes of stress reboot test.
Investigation of this issue revealed that when a single DDR chip select is used,
the hang does not happen. It only happens when the two chip selects are active.
MX53 reference manual states at "28.6.2 Memory ZQ calibration sequence":
"The controller must keep the memory lines quiet (except for CK) for the ZQ
calibration time as defined in the Jedec (512 cycles for ZQCL after reset, 256
for other ZQCL and 64 for ZQCS)."
According to the SDE_0 and SDE_1 bit descriptions from register ESDCTL_ESDCTL:
"Writing 1 to SDE0 or SDE1 will initiate power up delays as JEDEC defines.
Power up delays are a function of the configured memory type (DDR2/DDR3/LPDDR2)"
So make sure to activate one chip select at time (CS0 first and then CS1 later),
so that the required JEDEC delay is respected for each chip select.
With this change applied the board has gone through three days of reboot stress
test without any hang.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Since a clock function setup_gpmi_io_clk is implemented for GPMI
IO clock settings, change to use this common function in GPMI setup.
Signed-off-by: Ye.Li <B37916@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Add deep sleep support on Freescale LS1021QDS platform.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
[York Sun: Fix conflict in fdt.c]
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds LPUART support for LS1021ATWR board.
For ls1021atwr_nor_lpuart_defconfig, LPUART is used as the console.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds LPUART support for LS1021AQDS board.
For ls1021aqds_nor_lpuart_defconfig, LPUART is used as the console.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
CAAM is connected to CCI-400 S0 slave interface. Disable snooping for
S0 will cause CAAM self test failure. This patch is to enable snooping
for S0 slave interface. These CCI-400 operations are moved to
board_early_init_f() to be initialized earlier. For S4 slave interface,
issuing of snoop requests and DVM message requests are enabled.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds the CH7301 HDMI options and the common configuration
for DCU on LS1021AQDS board.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Cc: Jason Jin <Jason.Jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch reverts to use ge0_clk125 for eTSEC clock muxing. For SAI and
CAN which are pin multiplexed with RGMII1 in EC1 of RCW, ge2_clk125 will
be used via hwconfig.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
These boards are still non-generic boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Dave Liu <daveliu@freescale.com>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
This patch configures and initializes the L2 switch on T1040rdb board.
The external L2 switch ports may be connected to PHYs only over
QSGMII, for T1040rdb.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
This patch configures and initializes the L2 switch on T1040QDS board.
The L2 switch ports must be initialized according to the SerDes
protocols.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Freescale's T1040qds board may be configured to have up to
5 FMAN ports (FM1@DTSEC1 to FM1@DTSEC5). From these 5 ports,
2 of them may be fixed-links (FM1@DTSEC1 annd FM1@DTSEC2),
connected to other two ports from an intergrated
VSC9953 L2 Switch (switch ports 8 and 9). These fixed-link
ports have no PHYs attatched, so they don't have a
corresponding MDIO.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale's T1040qds board may be configured to have up to
5 FMAN ports (FM1@DTSEC1 to FM1@DTSEC5). From these 5 ports,
2 of them may be fixed-links (FM1@DTSEC1 annd FM1@DTSEC2),
connected to other two ports from an intergrated
VSC9953 L2 Switch (switch ports 8 and 9). These fixed-link
ports have no PHYs attatched, so they don't have a
corresponding MDIO.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The global_data pointer (gd) has already been set before board_init_f()
is called. We should not assign it again. We should also not use gdata since
it is going away.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since commit 1f98e31bc0 ("imx: mx6sxsabresd: Use the pfuze common init
function") board_late_init() became empty, so we can safely remove this unneeded
function.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
A new deep sleep interface is introduced to support generic
board structure. Converts it to use new interface.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
A new deep sleep interface is introduced to support generic
board structure. Converts it to use new interface.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1024RDB-PB board adds 2.5G SGMII support with AQR105 PHY.
rcw_0x095 is used for 10G XFI + 3x PCIex1
rcw_0x135 is used for 2.5G SGMII + 2x PCIex1
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
A new deep sleep interface is introduced to support generic
board structure. Converts it to use new interface.
Besides, added SPI/SD/NAND boot deep sleep support.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Secure boot target is added for T1042RDB platform.
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SerDes 2 protocol 56 is not valid any longer due to
the new RCW; protocol 55 is used instead, so add
SerDes 2 protocol 55 to align with RCW.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add NOR and SPI flash secure boot target for C29XPCIE board.
Signed-off-by: Po Liu <Po.Liu@freescale.com>
Signed-off-by: Mingkai.Hu <Mingkai.Hu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
All the 74xx_7xx boards are still non-generic boards:
P3G4, ZUMA, ppmc7xx, ELPPC, mpc7448hpc2
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Nye Liu <nyet@zumanetworks.com>
Cc: Roy Zang <tie-fei.zang@freescale.com>
Add spi nor boot support for mx6slevk board.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Configure the pad setting and enable qspi clock to support qspi
flashes access.
Add QSPI related macro in configuration header file.
Note:
mx6sxsabresd Revb board, 32M flash is used, but in header file,
CONFIG_SPI_FLASH_BAR is not defined, and we still use SZ_16M.
The LUT initialization qspi_set_lut function uses 32BIT addr,
however CONFIG_SPI_FLASH_BAR and 24BIT addr should be used to
access bigger than 16MB size flash, and BRRD/BRWR should also
be supported. Future patches will fix this.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
get_board_rev() just returns the cpu revision, which does not make it really
useful for distinguishing between revisions of the board.
Let's get rid of get_board_rev() as it is not being used with its correct
meaning.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
A new interface is introduced to support generic board structure.
Converts it to use new interface.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LS1 has 4 SMMUs for address translation of the masters. All the
SMMUs' stream IDs are 8-bit. The address translation depends on the
stream ID of the incoming transaction.
Each master has unique stream ID assigned to it and is configurable
through SCFG registers. The stream ID for the masters is identical
and share the same register field of STREAM ID registers.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The Central Security Unit (CSU) allows secure world software to
change the default access control policies of peripherals/bus
slaves, determining which bus masters may access them. This
allows peripherals to be separated into distinct security domains.
Combined with SMMU configuration of the system masters privileges,
these features provide protection against indirect unauthorized
access to data.
For now we configure all the peripheral access permissions as R/W.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
With the introducing of generic board and ARM-based cores, current
deep sleep framework doesn't work anymore.
This patch will convert the current framework to adapt this change.
Basically it does:
1. Converts all the Freescale's DDR driver to support deep sleep.
2. Added basic framework support for ARM-based and PPC-based
cores separately.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The Freescale LS1021AQDS share some pins, so Add the hwconfig option
that allows the user to choose which the function he wants.
The main pin mux IP is:
eSDHC, SAI, IIC2, RGMII, CAN, SAI.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds NAND boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from NAND flash to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds QSPI boot support for LS1021AQDS/TWR board.
The QSPI boot image need to be programmed into the QSPI flash
first. Then the booting will start from QSPI memory space.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds SD boot support for LS1021ATWR board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from SD card to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Chen Lu <chen.lu@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds SD boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from SD card to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Through adding CONFIG_QIXIS_I2C_ACCESS macro,
QIXIS_READ(reg)/QIXIS_WRITE(reg, value) can be used
for both i2c and ifc access to QIXIS FPGA. This is
more convenient for coding.
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When resuming from deep sleep, the I2C channel may not be
in the default channel. So, switch to the default channel
before accessing DDR SPD.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The patch changes PCIe dts node status to 'disabled' if the
corresponding controller is disabled according to serdes protocol.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
BRDCFG1_EMI1_SEL_MASK has been changed to 0x78, which contains
selection bits and connected status bit. So the Corresponding mux
value of RGMII is changed to BRDCFG1_EMI1_SEL_RGMII | BRDCFG1_EMI1_EN.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The new device trees use a more generic interface for
supporting muxing mdio buses. The mux property is thus
specified in "reg", rather than "fsl,hydra-mdio-muxval".
In order to support using old device trees, we keep the
old fixup in there. Linux will therefore see the both
properties, but will ignore fsl,hydra-mdio-muxval.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Increase IO drive strength to fix FCS error on RGMII ports
on T1024QDS.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add multiplexing support among SPI flash, TDM riser card and SDXC.
it routes SPI pins to SPI flash by default.
Route SPI pins to SD slot if "adaptor=sdxc" is set in hwconfig.
Route SPI pins to TDM riser card and do fixup for dts if "pin_mux=tdm"
is set in hwconfig.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1024RDB is a Freescale Reference Design Board that hosts the T1024 SoC.
T1024RDB board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3L SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- Two 10M/100M/1G RGMII ports on-board
- one 10Gbps XFI interface
- PCIe: Three PCIe controllers: one PCIe Slot and two Mini-PCIe connectors.
- SerDes: 4 lanes up to 10.3125GHz
- IFC: 128MB NOR Flash, 512MB NAND Flash and CPLD
- eSPI: 64MB N25Q512 SPI flash.
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- USB: Two Type-A USB2.0 ports with internal PHY
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC
- I2C: Four I2C controllers
- UART: Two UART serial ports
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT
Fix Kconfig by adding SUPPORT_SPL]
Reviewed-by: York Sun <yorksun@freescale.com>
T1024QDS is a high-performance computing evaluation, development and
test platform for T1024 QorIQ Power Architecture processor.
T1024QDS board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- Two 10M/100M/1G RGMII ports on-board
- Three 1G/2.5Gbps SGMII ports
- Four 1Gbps QSGMII ports
- one 10Gbps XFI or 10Base-KR interface
- SerDes: 4 lanes up to 10.3125GHz Supporting SGMII/QSGMII, XFI, PCIe, SATA and Aurora
- PCIe: Three PCI Express controllers with five PCIe slots.
- IFC: 128MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA
- Video: DIU supports video up to 1280x1024x32 bpp.
- Chrontel CH7201 for HDMI connection.
- TI DS90C387R for direct LCD connection.
- Raw (not encoded) video connector for testing or other encoders.
- QUICC Engine block
- 32-bit RISC controller for flexible support of the communications peripherals
- Serial DMA channel for receive and transmit on all serial channels
- Two universal communication controllers, supporting TDM, HDLC, and UART
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- eSPI: Three SPI flash devices.
- SATA: one SATA 2.O.
- USB: Two USB2.0 ports with internal PHY (one Type-A + one micro Type mini-AB)
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC.
- I2C: Four I2C controllers.
- UART: Two UART on board.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT
Fix Kconfig by adding SUPPORT_SPL]
Reviewed-by: York Sun <yorksun@freescale.com>
T2080 v1.1 requires different MEM_PLL_RAT from previous v1.0,
and also update core frequency to 1.8GHz for v1.1.
We reserve the support for T2080 v1.0 and enable v1.1 by default.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
In B4860QDS board SerDes2 lanes EFGH either go to SFP or AMC riser card
slot2 so either DTSEC3/DTSEC4 or TGEC1/TGEC2 should be accessible. This
Patch enables DTSEC3/DTSEC4 or TGEC1/TGEC2 on bases of user specified
string fsl_b4860_serdes2:sfp_amc=amc or fsl_b4860_serdes2:sfp_amc=sfp
respectively in hwconfig.
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
XFI does not work stable on current board, it's due to heat sink issue,
to make it work stable the board needs additional heat sink, enable two
XFI lanes only. Right now we do not have such an erratum for the issue,
so use a define CONFIG_SYS_FSL_B4860QDS_XFI_ERR to identify it.
The workaround will only be used in XFI protocols and only if the
hwconfig indicates that XFI is prefered.
A new VSC3308 config function is used instead of re-use the original
function, to avoid making the function complex and ugly.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SerDes2 lanes EFGH either go to SFP or AMC riser card slot2.
By default AMC will be configured even if no hwconfig is specified.
To enable XFI via SFP use the below hwconfig:
fsl_b4860_serdes2:sfp_amc=sfp
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@ffeescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Since xfi has no phy, we delete the property "phy-handle" and use
a "fixed-link" property for a xfi port.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
We need following changes to make xfi work on B4:
1. set cross-point switch VSC3308 to use sfp config when running xfi;
2. add 10G interface check for xfi;
3. set phy address for xfi so the 10G ports can be registered by mdio;
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add the support of newly added LC VCO SerDes protocols
for configuration of IDT and VSC crossbar
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
B4860, B4440, B4420 and B4220 have MAPLE, so enable law creation
for them only. Remove static LAW creation for MAPLE.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory.
These values define the voltage requirements for
the chip. u-boot reads FUSESR and translates the values
into the appropriate commands to set the voltage output
value of an external voltage regulator.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Workaround of Errata A-008044 was implemented without errata number and it is
enabled by default. Errata A-008044 is only valid for T1040 Rev 1.0.
So put errata number and make it conditional.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When device is configured to load RCW from NAND flash IFC_A[16:31] are driven
low after RCW loading. Hence Devices connected on IFC_CS[1:7] and using
IFC_A[16:31] lines are not accessible.
Workaround is already in-place.
Put the errata number to adhere errata handling framework.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Adjust timing for dual-rank UDIMM, verified on M3CQ-8GHS3C0E for speed of
1066, 1333, 1600, 1866MT/s. The 1866 timing is copied to 2133 timing in
case such DIMM comes available.
Also update single-rank 1866 timing. Enable interactive debugging as well.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Shengzhou Liu <Shengzhou.Liu@freescale.com>
As checkpatch complaines about these camel-case defines, lets change
them to only use upper-case characters.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Jon Nettleton <jon.nettleton@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
EC1 pins in RCW can be selected as RGMII1, GPIO3, CAN1/2, FTM1 or
SAI1/2. There is a bug that EC3 RGMII could not work when selecting EC1
as other functionality except RGMII. The workaround is to select
ge2_clk125 for eTSEC clock muxing in register SCFG_ETSECCMCR.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SystemID information could be read through I2C1 from EEPROM
on LS1021ATWR board.
As LS1 is a little-endian processor, getting the version ID by
be32_to_cpu() is wrong. Fix it by using e.version directly.
This change will be compatible for both ARM and PowerPC.
As there is an errata that I2C1 could not work in SD boot,
reading EEPROM through I2C1 is disabled too in SD boot.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SCFG_SCFGREVCR is SCFG bit reverse register. This register
must be written with 0xFFFFFFFF before writing to any other
SCFG register. Then other SCFG register could be written in
big-endian mode.
Address: 157_0000h base + 200h offset = 157_0200h
Bit 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15|16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
W/R SCFGREV
Reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0-31
SCFGREV SCFG Bit Reverse Control Filed
32'h 0000_0000 - No bit reverse is applied
32'h FFFF_FFFF - Bit reverse is applied; so 31:0 will be stored/read as
0:31
This patch removes the bit reversing for SCFG registers in
u-boot. It will be implemented through PBI commands in RCW
.pbi
write 0x570200, 0xffffffff
.end
So other SCFG register could be written in big-endian mode
in u-boot or kernel directly.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Disable the snoop for slave interface 0, 1 and 2
to avoid the interleaving on the CCI400 BUS.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.
Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Use these new functions where possible. They default to a value of 2 so we
cannot use them in some places where we need a default value of 1.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
This function can fail if the device tree runs out of space. Rather than
silently booting with an incomplete device tree, allow the failure to be
detected.
Unfortunately this involves changing a lot of places in the code. I have
not changed behvaiour to return an error where one is not currently
returned, to avoid unexpected breakage.
Eventually it would be nice to allow boards to register functions to be
called to update the device tree. This would avoid all the many functions
to do this. However it's not clear yet if this should be done using driver
model or with a linker list. This work is left for later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Modify the pfuze init for mx6sxsabresd to use the shared
"pfuze_common_init" function. And move this initialization to
power_init_board.
Signed-off-by: Ye.Li <B37916@freescale.com>
Modify the pfuze init for mx6sabresd to use the shared
"pfuze_common_init" function. And move this initialization to
power_init_board.
Signed-off-by: Ye.Li <B37916@freescale.com>
Since the Pfuze initializations are similar on various mx6 SABRE
boards. Factorize the initialization to a common function in file
board/freescale/common/pfuze.c. So that all SABRE boards BSP can
share the function.
Signed-off-by: Ye.Li <B37916@freescale.com>
Add full support for USDHC2, USDHC3, USDHC4 on mx6sx sabresd board.
The default boot socket is USDHC4, so the MMC environment device and
mmcdev variable are set to this device.
Signed-off-by: Ye.Li <B37916@freescale.com>
In U-boot it is preferred to access the register via structure pointer, so
convert it such style.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Let's add mx6sabresd_spl_defconfig entry into MAINTAINERS, so that we avoid
getting a warning that the mx6sabresd_spl is not maintained.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
We can simply the return the value from enable_fec_anatop_clock() to make the
code smaller and simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
We can simply the return the value from enable_fec_anatop_clock() to make the
code smaller and simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
mx6sabreauto boards come with 32 MiB of parallel NOR flash.
Add support for it:
U-Boot 2015.01-rc1-18107-g1543636-dirty (Nov 14 2014 - 11:11:04)
CPU: Freescale i.MX6Q rev1.2 at 792 MHz
Reset cause: POR
Board: MX6Q-Sabreauto revA
I2C: ready
DRAM: 2 GiB
Flash: 32 MiB
NAND: 0 MiB
Due to pin conflict with I2C3, only define configure I2C3 IOMUX when flash is
not used.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Many boards use a minimal .cfg file in the SPL case.
Introduce spl_sd.cfg so that we can reuse it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
mx6sabresd_spl.cfg configures CCM registers, GPR registers and CCM_CCOSR.
Move the configuration to the spl code.
CCM_CCOSR setting is no longer required to get audio functionality in the
kernel, so remove such setting.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The PFUZ probe failed with the following msg:
" wait_for_sr_state: failed sr=81 cr=a0 state=2020
i2c_init_transfer: failed for chip 0x8 retry=0
wait_for_sr_state: failed sr=81 cr=a0 state=2020
i2c_init_transfer: failed for chip 0x8 retry=1
wait_for_sr_state: failed sr=81 cr=a0 state=2020
i2c_init_transfer: failed for chip 0x8 retry=2
i2c_init_transfer: give up i2c_regs=021a0000
Can't find PMIC:PFUZE100 "
board_early_init_f is too early to call i2c related setting, because
init_func_i2c is called after board_early_init_f being invoked. Thus
move setup_i2c into board_init.
Also PFUZ is connected to I2C bus 0, so change "1" -> "0".
Using this patch PFUZ can be correctly probed:
"PMIC: PFUZE100 ID=0x11"
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
1000BASE-KX(1G-KX) uses SGMII protocol but the serdes lane runs in 1G-KX
mode. By default, the lane runs in SGMII mode, when a MAC uses a lane
in 1G-KX mode, corresponding bit in PCCR1 for the lane needs to be set,
and needs to fixup dtb accordingly for kernel to do proper initialization.
Hwconfig "fsl_1gkx" is used to indicate a MAC runs in 1G-KX mode, FM1 MAC
1/2/5/6/9/10 are available for 1G-KX, MAC 3/4 run in RGMII mode. To set a
MAC runs in 1G-KX mode, set its' corresponding env in "fsl_1gkx",
'fm1_1g1' stands for FM1-MAC1, 'fm1_1g2' stands for FM1-MAC2, etc.
If all MAC 1/2/5/6/9/10 run in 1G-KX mode, the hwconfig should has below
setting:
fsl_1gkx:fm1_1g1,fm1_1g2,fm1_1g5,fm1_1g6,fm1_1g9,fm1_1g10
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
[York Sun: Fix compiling warning]
Reviewed-by: York Sun <yorksun@freescale.com>
XFI ports on t2080qds can work with fiber cable and direct attach
cable(copper). We use hwconfig to define cable type for XFI, and fixup
dtb based on the cable type.
For copper cable, set below env in hwconfig:
fsl_10gkr_copper:<10g_mac_name>
the <10g_mac_name> can be fm1_10g1, fm1_10g2, fm1_10g3, fm1_10g4.
fm1_10g1 stands for FM1-MAC9, fm1_10g2 stands for FM1-MAC10, fm1_10g3
stands for FM1-MAC1, fm1_10g4 stands for FM1-MAC2. The four
<10g_mac_name>s do not have to be coexist in hwconfig. For XFI ports, if
a given 10G port will use the copper cable for 10GBASE-KR, set the
<10g_mac_name> of the port in hwconfig, otherwise, fiber cable will be
assumed to be used for the port.
For ex. if four XFI ports will both use copper cable, the hwconfig
should contain:
fsl_10gkr_copper:fm1_10g1,fm1_10g2,fm1_10g3,fm1_10g4
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add pinmux settings, implement board_ehci_hcd_init, board_usb_phy_mode
There are two usb port on mx6sxsabresd board:
1. otg port
2. host port
The following are the connection between usb controller and board usb
interface, host port has not ID pin set:
otg1 core <---> board otg port
otg2 core <---> board host port
In order to make host port work, board_usb_phy_mode return USB_INIT_HOST
to make host port work in HOST mode.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye Li <B37916@freescale.com>
Add pinmux settings, implement board_ehci_hcd_init, board_usb_phy_mode
There are two usb port on mx6slevk board:
1. otg port
2. host port
The following are the connection between usb controller and board usb
interface, host port has not ID pin set:
otg1 core <---> board otg port
otg2 core <---> board host port
In order to make host port work, board_usb_phy_mode return USB_INIT_HOST
to let host port work in host mode.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye Li <B37916@freescale.com>
* fdt_fixup_mtdparts is called from ft_board_setup
* Run "mtdparts default" to create NAND partition on uboot
* Use mtdparts to create partitions dynamically rather
than using static partitions in device tree
Signed-off-by: Ashish Kumar <Ashish.Kumar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
* fdt_fixup_mtdparts is called from ft_board_setup
* run "mtdparts default" to create NAND, NOR partition on uboot
* Use mtdparts to create partitions dynamically rather
than using static partitions in device tree
Signed-off-by: Ashish Kumar <Ashish.Kumar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
-A_007662 states that for x1 link width, PCIe2 controller trains in
Gen1 speed while configured for Gen2 speed.
Workaround:Set the width to x1 and speed to Gen2 by writing to
CCSR registers in PBI phase
-A_008007 states that PVR register may show random value.
Workaround: Reset PVR register using DCSR space in PBI phase
Add PBI based software workaround for A_007662 and A_008007
in t104x_pbi.cfg. This is required for SPL-based bootloaders
like NAND-boot, SD-boot, SPI-boot
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This support of CPLD includes
- Files and register definitions
- Command to switch alternate bank
- Command to switch default bank
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch will enable the support for SPL on iMX6 SabreSD.
It tested on SD2 and SD3 mmc port (Switch 1 or 2 of SW6)
Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The i.MX6Q/DL sabreauto board has one NAND socket, set the
CONFIG_NAND_MXS and relevant NAND configurations to enable the
MXS NAND flash driver.
Add board level codes to set IOMUX and clock for GPMI-NAND and
BCH module.
Signed-off-by: Ye.Li <B37916@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Since kernel 3.15 there are two dtb's for the imx53-qsb board:
imx53-qsb.dtb - For the boards with DA9053 PMIC
imx53-qsrb.dtb - For the boards with MC34708 PMIC
Change the 'fdt_file' dynamically, so that the correct dtb can be used depending
on the board variant.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
On mx6 sabreauto board, there are two USB ports:
0: OTG
1: HOST
The EHCI driver is enabled for this board, but the IOMUX and VBUS power
control is not implemented, which cause both USB port failed to work.
This patch fix the problem by adding the board support codes.
Since the power control uses the GPIO pin from port expander MAX7310,
the PCA953X driver is enabled for accessing the MAX7310.
The ID pin of OTG Port needs to configure the GPR1 bit 13 for selecting
its daisy chain. Add a new function "imx_iomux_set_gpr_register" to
handle GPR register setting.
Signed-off-by: Ye.Li <B37916@freescale.com>
There are three SD/MMC sockets on mx6slevk boards. Implements the
full support for them.
The default boot socket is USDHC2, so the MMC environment is set
to that device.
Signed-off-by: Ye.Li <B37916@freescale.com>
Add support for the 4.3'' Seiko WVGA parallel display.
In order to direct the splash screen to the Seiko display:
=> setenv panel SEIKO-WVGA
=> save
=> reset
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
