Since the 'clock-freq-min-max' is deprecated, we use max-frequency for
all rockchip SoC dwmmc controller.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
With the new dev_read functions available, we can convert the rockchip
architecture-specific drivers and common drivers used by these devices
over to the dev_read family of calls.
This covers the dw_mmc and sdhci wrapper drivers for Rockchip.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver is used in another board; remove board information from
the driver debug log.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This reverts commit ddb3ac3c71.
With MMC converted to driver model, SCSI driver is broken due to
zero address access at (ops->read) in block_dread() function.
The fix (SCSI driver converted to DM) is ready in u-boot-dm branch,
but it is too late for this relese to get that in.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The driver currently does not reset bit 5 of the hostctl register even if
the MMC stack requests it. Then means that once a bus width of 8 is
selected it is not possible to change it back to 1. This breaks
'mmc rescan' which needs to start off with a bus width of 1.
The problem was surfaced by enabling CONFIG_DM_MMC_OPS on tegra. Without
this option the MMC stack fully reinits the driver on a 'mmc rescan'.
But with this option driver model does not re-probe a driver once it has
been probed once.
Fix the driver to honour the request.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Peter Chubb <peter.chubb@data61.csiro.au>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We do not need to probe the block device here, so avoid doing so. The MMC
device itself must be active, but the block device can come later.
Signed-off-by: Simon Glass <sjg@chromium.org>
The Kconfig entry depends on RMOBILE, but this was renamed
to ARCH_RMOBILE in commit 1cc95f6e1b (ARM: Rmobile: Rename
CONFIG_RMOBILE to CONFIG_ARCH_RMOBILE) . Fix this omission.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
R-Car Gen3 series have four SD card interfaces (SDHI0 to SDHI3),
two of which can also be used as MMC interfaces (SDHI2 and SDHI3).
This adds High-speed mode SD clock frequency between 25MHz and 50MHz,
8bit/4bit bus width, high capacity and low voltage device support.
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add support for requesting GPIOs with a live device tree.
This involves adjusting the function signature for the legacy function
gpio_request_by_name_nodev(), so fix up all callers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes to stm32f746-disco.c:
Signed-off-by: Tom Rini <trini@konsulko.com>
The of_ prefix conflicts with the livetree version of this function.
Rename it to avoid problems when we add livetree support.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable CONFIG_DM_MMC_OPS and CONFIG_BLK for all Tegra devices. This moves
Tegra to use driver model fully for MMC.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is called when the MMC block device is being probed. There
is a recursive call in this function since find_mmc_device() itself can
cause the MMC device to be probed.
Admittedly the MMC device should already be probed, since we would not be
probing its child otherwise, but the current code is unnecessarily
convoluted.
Rewrite this to access the MMC structure directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
When binding a new MMC device, make sure that it has the required
operations. Since for now we still support *not* having the operations
(with CONFIG_DM_MMC_OPS not enabled) it makes sense to add this check.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should not call out to board code from drivers. With driver model,
mmc_power_init() already has code to use a named regulator, but the
legacy code path remains. Update the code to make this clear.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is good practice to include common.h as the first header. This ensures
that required features like the DECLARE_GLOBAL_DATA_PTR macro,
configuration options and common types are available.
Fix up some files which currently don't do this. This is necessary because
driver model will soon start using global data and configuration in the
dm/read.h header file, included via dm.h. The gd->fdt_blob value will be
used to access the device tree and CONFIG options will be used to
determine whether to support inline functions in the header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.
In the end we will have:
1. dev_read_addr...() - works on devices, supports flat/live tree
2. devfdt_get_addr...() - current functions, flat tree only
3. of_get_address() etc. - new functions, live tree only
All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.
Note this involves changing some dead code - the imx_lpi2c.c file.
Signed-off-by: Simon Glass <sjg@chromium.org>
This header includes things that are needed to make driver build. Adjust
existing users to include that always, even if other dm/ includes are
present
Signed-off-by: Simon Glass <sjg@chromium.org>
Don't build non DM_MMC code when DM_MMC defined so move
them into #ifndef CONFIG_DM_MMC
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
On i.MX, SYSCTL.SDCLKFS may be set to 0 in order to make the SD clock
frequency prescaler divide by 1 in SDR mode. In DDR mode, the prescaler
can divide by up to 512. Allow both of these settings.
The maximum SD clock frequency in High Speed mode is 50 MHz. On i.MX25,
this change makes it possible to get 48 MHz from the USB PLL
(240 MHz / 5 / 1) instead of only 40 MHz from the USB PLL
(240 MHz / 3 / 2) or 33.25 MHz from the AHB clock (133 MHz / 2 / 2).
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Number of blocks is a 9 bit field where 0 stands for a unlimited
number of blocks. Therefore the max number of blocks which can
be set is 511.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Convert the pci_mmc driver over to driver model and migrate all x86 boards
that use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
To fix the timeout of sending the write command, enable the quirk
SDHCI_QUIRK_WAIT_SEND_CMD.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This simplifies makefiles. Also, arrange the order of objects in
drivers/mmc/Makefile so that the framework objects are listed before
drivers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now CONFIG_GENERIC_MMC and CONFIG_MMC match for all defconfig.
We do not need two options for the same feature. Deprecate the
former.
This commit was generated with the sed script 's/GENERIC_MMC/MMC/'
and manual fixup of drivers/mmc/Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This driver is a counterpart of drivers/mmc/host/sdhci-cadence.c
from Linux. Some updates for v4.12-rc1 can be imported to U-Boot.
- Fix value of SDHCI_CDNS_HRS04_RDATA_SHIFT
- Add polling for ACK bit to be sure that data are written to
the PHY register
- Retrieve PHY values from DT properties instead of fixed data
The following is the list of upstream commits:
- Linux commit 4e03f628b464e0580abadf5161eaa38c61d20943
mmc: sdhci-cadence: fix bit shift of read data from PHY port
- Linux commit a0f8243229ed071c8da0ea7cedc1b7bf1b1515da
mmc: sdhci-cadence: Fix writing PHY delay
- Linux commit a89c472d8b55c5afc4c79e6e3d1338730034eb01
mmc: sdhci-cadence: Update PHY delay configuration
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In the programmable clock mode, the SDCLK frequency is incorrectly
assigned when the maximum clock has been assigned during probe,
this causes the SDHCI not work well.
In the programmable clock mode, when calculating the SDCLK Frequency
Select, when the maximum clock has been assigned, it is the actual
value, should not be multiplied by host->clk_mul. Otherwise, the
maximum clock is multiplied host->clk_mul by the base clock achieved
from the BASECLKF field of the Capabilities 0 Register.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
For platforms that don't use device tree in SPL the only
way to mark this driver as 'required by relocation' is
with the DM_FLAG_PRE_RELOC flag. Add this to ensure that
the driver is bound.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The 'clock-freq-min-max' property was deprecated in the upstream
(i.e. Linux) DTS bindings in favor of the 'max-frequency' property.
With the latest RK3399 DTSI does no longer include the deprecated
property and the rockchip_dw_mmc driver requiring it to be present,
the driver doesn't bind to the node in the RK3399 DTSI any longer
(thus breaking access to the SD card on the RK3399-Q7 board).
To fix this, we implement a similar logic as in the Linux driver: if
the deprecated property is present, we issue a warning (if DEBUG is
enabled); if it is missing, we require 'max-frequency' to be set and
use it to create a min/max value-pair.
See b023030f10
for the deprecation/matching change in Linux.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
As you know, biu_clk is used for AMBA AHB/APB interface, ciu_clk is
used for communication between host and card devices. The real bus clock
is ciu, so let's rectify it.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch changes the way DM_MMC calculates offset to the base register of
MMC. Previously this was through an #ifdef but that wasn't necessary for OMAP3.
This patch will now add in the offset to the base address based on the
.compatible flags.
Signed-off-by: Adam Ford <aford173@gmail.com>
V2: Remove ifdef completely and reference offset from the omap_hsmmc_ids table.
V1: Change ifdef to ignore OMAP3
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert the bcm2835 SDHCI driver over to support CONFIG_DM_MMC and move
all boards over. There is no need to keep the old code since there are no
other users.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
These drivers have no user since commit ea3310e8aa ("Blackfin:
Remove").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
sdhci_transfer_data() function transfers the blocks passed up to the
number of blocks defined in mmc_data, but returns immediately once all
the blocks are transferred, even if the loop exit condition is not met
(bit SDHCI_INT_DATA_END set in the STATUS word).
When doing multiple writes to mmc, returning right after the last block
is transferred can cause the write to fail when sending the
MMC_CMD_STOP_TRANSMISSION command right after the
MMC_CMD_WRITE_MULTIPLE_BLOCK command, leaving the mmc driver in an
unconsistent state until reboot. This error was observed in the rpi3
board.
This patch waits for the SDHCI_INT_DATA_END bit to be set even after
sending all the blocks.
Test: Reliably wrote 2GiB of data to mmc in a rpi3.
Signed-off-by: Alex Deymo <deymo@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The linux kernel driver for this module does not use a delay when
writing to the SDHCI_BUFFER register. This patch mimics that behavior
in order to speed up the mmc writes on the Raspberry Pi.
Signed-off-by: Alex Deymo <deymo@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the driver model support for Atmel mci while retaining the
existing legacy code. This allows the driver to support boards
that have converted to driver model as well as those that have not.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver implements MMC support on Meson GX (S905) based systems.
It's based on Carlo Caione's work, changes:
- BLK support added
- general refactoring
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
This patch adds the flags parameter to device_remove() and changes all
calls to this function to provide the default value of DM_REMOVE_NORMAL
for "normal" device removal.
This is in preparation for the driver specific pre-OS (e.g. DMA
cancelling) remove support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Introduce CONFIG_TEGRA124_MMC_DISABLE_EXT_LOOPBACK to disable the external clock
loopback and use the internal one on SDMMC3 as per the SDMMC_VENDOR_MISC_CNTRL_0
register's SDMMC_SPARE1 bits being set to 0xfffd according to the TRM.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This is a preparation work for the support of CONFIG_BLK.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
For consistency, use an accessor to access the private data. Also for the
same reason, rename all priv_data to priv.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The Xenon SDHCI driver just missed the integration of this patch:
git ID 6d0e34bf
mmc: sdhci: Distinguish between base clock and maximum peripheral frequency
With this patch applied, the SDHCI subsystem complains now with this warning
while probing:
sdhci_setup_cfg: Hardware doesn't specify base clock frequency
This patch fixes this issue, by providing the missing host->max_clk
variable to the SDHCI subsystem.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Hu Ziji <huziji@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
It's redundant to send cmd13 after cmd9 whose response is not R1b. The
card devices will not be busy w/ cmd9.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
This patch adds Intel Tangier eMMC/SDHCI driver.
Intel Tangier SoC contains a hybrid of PCI and non-PCI devices. SDHCI
controller is one of the devices which are *not* on a PCI and, hence,
cannot be enumerated by standard PCI means. This driver, allows for
SDHCI controller on Tangier SoC to work in U-Boot.
Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We don't want pci_mmc to compile every time x86 compiles, only when
there's a platform that needs it. For that reason, we're adding a new
CONFIG_MMC_PCI which platforms can choose to enable.
Suggested-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This includes support for rk3188 from Heiko Stübner and and rk3328 from
Kever Yang. Also included is SPL support for rk3399 and a fix for
rk3288 to get it booting again (spl_early_init()).
Add compatible property for i.MX7ULP.
Add a weak init_usdhc_clk function, i.MX7ULP use this to init the clock.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Change some API in order to enable of-platdata.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added rockchip tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
- Move to DM clk driver
- Add clk support for zynq_sdhci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAljKWVcACgkQykllyylKDCEsgACfey0mgRaGVMLSxMMCGgJQIK70
/oYAn3raqYrJ2e2fsjb1B5WodYcDe8L5
=JYC5
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2017.05' of git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2017.05
- Move to DM clk driver
- Add clk support for zynq_sdhci
This device tree has been extracted from v4.9 kernel
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add SDHCI host controller found on STMicroelectronics SoCs
On some ST SoCs, i.e. STiH407/STiH410, the MMC devices can live
inside a dedicated flashSS sub-system that provides an extend subset
of registers that can be used to configure the Arasan MMC/SD Host
Controller.
This means, that the SDHCI Arasan Controller can be configured to be
eMMC4.5 or 4.3 spec compliant.
W/o these settings the SDHCI will configure and use the MMC/SD
controller with limited features e.g. PIO mode, no DMA, no HS etc.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The maximum supported peripheral clock frequency of the zynq depends on
the IO routing. The MIO and EMIO support a maximum frequency of 50 MHz
respectively 25 MHz. Use the max-frequency value of the device tree to
determine the maximal supported peripheral clock frequency.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The zynq_sdhci controller driver use CONFIG_ZYNQ_SDHCI_MAX_FREQ as base
clock frequency but this clock is not fixed and depends on the hardware
configuration. Additionally the value of CONFIG_ZYNQ_SDHCI_MAX_FREQ
doesn't match the real base clock frequency of SDIO_FREQ. Use the clock
framework to determine the frequency at run time.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
It was incorrect to always include "asm/arch-omap3/mux.h" constantly.
This introduced warnings on non-omap3 where certain values will conflict
between the various families. Conditionally guard the inclusion in
order to correct the problem.
Fixes: 6aca17c9b7 ("drivers: mmc: omap_hsmmc: Fix IO Buffer on OMAP36xx")
Signed-off-by: Tom Rini <trini@konsulko.com>
MMC devices accessed exclusively via the driver model were not
being initialized before being exposed as block devices, causing
issues in scenarios where the MMC device is first accessed via the
uclass block interface.
Signed-off-by: Fiach Antaw <fiach.antaw@uqconnect.edu.au>
On the OMAP36xx/37xx the CONTROL_WKUP_CTRL register has
a field (bit 6) named GPIO_IO_PWRDNZ. If 0, the IO buffers which
are related to GPIO_126, 127 and 129 are disabled. Some boards may
need this for MMC. After the PBIAS is configured, this bit should
be set high to enable these GPIO pins.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
ftsdc021_sdhci.c is dead file.
There is no reason to maintain this host controller.
Removes the entire ftsdc021_sdhci.c.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
If there are alias nodes as "mmc", use the devnum as alias index
number.
This patch is for fixing a problem of Exynos4 series.
Problem is the below thing.
Current legacy mode:
EXYNOS DWMMC: 0, SAMSUNG SDHCI: 1
After using DM:
SAMSUNG SDHCI: 0, EXYNOS DWMMC: 1
Dev index is swapped.
Then u-boot can't find the kernel image..because it is already set to 0 as mmcdev.
If change from legacy to DM, also needs to touch all exynos4 config file.
For using simply, just supporting the fixed devnum with alias node is better than it.
Usage:
alaise {
....
mmc0 = &sdhci2; /* eMMC */
mmc1 = &sdhci1; /* SD */
...
}
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
While we are here, add "depends on ARCH_AT91".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
While we are here, add "depends on ARCH_ROCKCHIP".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
While we are here, add "depends on ARCH_ZYNQ || ARCH_ZYNQMP".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[1] Rename CONFIG_SANDBOX_MMC to CONFIG_MMC_SANDBOX for consistency
I want all MMC driver options prefixed with CONFIG_MMC_.
[2] Fix dependency
Add necessary depends on to avoid compile error.
Instead "depends on MMC" is unneeded because this config entry
resides inside of "if MMC".
[3] Currently, this config symbol is not referenced at all.
Use it to enable/disable the driver in Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now, CONFIG_GENERIC_MMC seems equivalent to CONFIG_MMC.
Let's create an entry for "config GENERIC_MMC" with "default MMC",
then convert all macro defines in headers to Kconfig. Almost all
of the defines will go away.
I see only two exceptions:
configs/blanche_defconfig
configs/sandbox_noblk_defconfig
They define CONFIG_GENERIC_MMC, but not CONFIG_MMC. Something
might be wrong with these two boards, so should be checked later.
Anyway, this is the output of the moveconfig tool.
This commit was created as follows:
[1] create a config entry in drivers/mmc/Kconfig
[2] tools/moveconfig.py -r HEAD GENERIC_MMC
[3] manual clean-up of garbage comments in doc/README.* and
include/configs/*.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This driver implementes platform specific code for the Xenon SDHCI
controller which is integrated in the Marvell MVEBU Armada 37xx and
Armada 7k / 8K SoCs.
History:
This driver is ported from the Marvell U-Boot version 2015.01 which is
written by Victor Gu <xigu@marvell.com> with minor changes ported from
the Linux driver which is written by Ziji Hu <huziji@marvell.com>.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Some SDHCI drivers might need to do some special controller configuration
after the common clock set_ios() function has been called (speed / width
configuration). This patch adds a call to the newly created function
set_ios_port() when its configured in the host driver.
This will be used by the Xenon SDHCI controller driver used on the
Marvell Armada 3700 and 7k/8k ARM64 SoCs.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This patch completely clears the SDHCI_CLOCK_CONTROL register before the
new value is configured instead of just clearing the 2 bits
SDHCI_CLOCK_CARD_EN and SDHCI_CLOCK_INT_EN. Without this change, some
clock configurations will lead to the "Internal clock never stabilised."
error message on the Xenon SDHCI controller used on the Marvell Armada
3700 and 7k/8k ARM64 SoCs.
The Linux SDHCI core driver also writes 0 to this register before
the new value is configured. So this patch simplifies the driver a bit
and brings the U-Boot driver more in-line with the Linux one.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Print the error code for non-zero (failure case) instead
of making debug statement without any condition, this
usually gives proper clue in failure condition.
Log:
The sdhci controller assumes that the base clock frequency is fully supported by
the peripheral and doesn't support hardware limitations. The Linux kernel
distinguishes between base clock (max_clk) of the host controller and maximum
frequency (f_max) of the card interface. Use the same differentiation and allow
the platform to constrain the peripheral interface.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Move fdt fixup of 'status' property into a weak function. This allows
board to define 'status' fdt fixup by themselves.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch is to add 'fsl,esdhc' into of_match table to support
driver model for QorIQ eSDHC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
There would be compiling error as below when enable driver model for esdhc.
undefined reference to `dm_gpio_get_value'
undefined reference to `gpio_request_by_name_nodev'
This patch is to make GPIO support optional with CONFIG_DM_GPIO. Because
all boards of QorIQ platform don't need it and they just check register for
CD/WP status, only some boards of i.MX platform require this.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Commit f401e907fc ("ARM: sunxi: remove bare default for
CONFIG_MMC") dropped "depends on UART0_PORT_F", but it is still
needed. Revive it as a prerequisite of CONFIG_MMC_SUNXI.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Until recently, sdhci_ops was used only for overriding IO accessors.
(so, host->ops was not set by any drivers except bcm2835_sdhci.c)
Now, we have more optional callbacks, get_cd, set_control_reg, and
set_clock. However, the code
if (host->ops->get_cd)
host->ops->get_cd(host);
... expects host->ops is set for all drivers.
Commit 5e96217f04 ("mmc: pic32_sdhci: move the code to
pic32_sdhci.c") and commit 62226b6863 ("mmc: sdhci: move the
callback function into sdhci_ops") added sdhci_ops for pic32_sdhci.c
and s5p_sdhci.c, but the other drivers still do not (need not) set
host->ops because all callbacks in sdhci_ops are optional.
host->ops must be checked to avoid the system crash caused by NULL
pointer access.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Init the clock rate to max-frequency from dts with clock driver api.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Move (and rename) the following CONFIG options to Kconfig:
CONFIG_DAVINCI_MMC (renamed to CONFIG_MMC_DAVINCI)
CONFIG_OMAP_HSMMC (renamed to CONFIG_MMC_OMAP_HS)
CONFIG_MXC_MMC (renamed to CONFIG_MMC_MXC)
CONFIG_MXS_MMC (renamed to CONFIG_MMC_MXS)
CONFIG_TEGRA_MMC (renamed to CONFIG_MMC_SDHCI_TEGRA)
CONFIG_SUNXI_MMC (renamed to CONFIG_MMC_SUNXI)
They are the same option names as used in Linux.
This commit was created as follows:
[1] Rename the options with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_DAVINCI_MMC/CONFIG_MMC_DAVINCI/g
s/CONFIG_OMAP_HSMMC/CONFIG_MMC_OMAP_HS/g
s/CONFIG_MXC_MMC/CONFIG_MMC_MXC/g
s/CONFIG_MXS_MMC/CONFIG_MMC_MXS/g
s/CONFIG_TEGRA_MMC/CONFIG_MMC_SDHCI_TEGRA/g
s/CONFIG_SUNXI_MMC/CONFIG_MMC_SUNXI/g
'
[2] Commit the changes
[3] Create entries in driver/mmc/Kconfig.
(copied from Linux)
[4] Move the options with the following command
tools/moveconfig.py -y -r HEAD \
MMC_DAVINCI MMC_OMAP_HS MMC_MXC MMC_MXS MMC_SDHCI_TEGRA MMC_SUNXI
[5] Sort and align drivers/mmc/Makefile for readability
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Move (and rename) the following CONFIG options to Kconfig:
CONFIG_EXYNOS_DWMMC (renamed to CONFIG_MMC_DW_EXYNOS)
CONFIG_HIKEY_DWMMC (renamed to CONFIG_MMC_DW_K3)
CONFIG_SOCFPGA_DWMMC (renamed to CONFIG_MMC_DW_SOCFPGA)
The "HIKEY" is a board name, so it is not suitable for the MMC
controller name. I am following the name used in Linux.
This commit was generated as follows:
[1] Rename the config options with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_EXYNOS_DWMMC/CONFIG_MMC_DW_EXYNOS/g
s/CONFIG_HIKEY_DWMMC/CONFIG_MMC_DW_K3/g
s/CONFIG_SOCFPGA_DWMMC/CONFIG_MMC_DW_SOCFPGA/g
'
[2] Commit the changes
[3] Create the entries in drivers/mmc/Kconfig
(with default y for EXYNOS and SOCFPGA)
[4] Run the following:
tools/moveconfig.py -y -r HEAD MMC_DW_EXYNOS MMC_DW_K3 MMC_DW_SOCFPGA
[5] Sort and align drivers/mmc/Makefile for readability
[6] Clean-up doc/README.socfpga by hand
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This commit was created as follows:
[1] Rename the option with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e 's/CONFIG_DWMMC/CONFIG_MMC_DW/g'
[2] create the entry for MMC_DW in drivers/mmc/Kconfig
(the prompt and help were copied from Linux)
[3] run "tools/moveconfig.py -y MMC_DW"
[4] add "depends on MMC_DW" to the MMC_DW_ROCKCHIP entry
[5] Clean-up doc/README.socfpga by hand
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
I am trying to make all DesignWare-based driver options prefixed
with CONFIG_MMC_DW_.
This commit was generated as follows:
find . -name .git -prune -o -type f -print | \
xargs sed -i -e 's/ROCKCHIP_DWMMC/MMC_DW_ROCKCHIP/g'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Some MMC drivers describe operations with the DM_MMC_OPS form, but
there are still several drivers with older implementation. We can
not compile drivers from different groups at the same time because
the core framework is shared with #ifdef CONFIG_DM_MMC_OPS.
Every driver should have "depends on DM_MMC_OPS" (or !DM_MMC_OPS)
explicitly to express which framework it is based on. This will
avoid enabling drivers with incompatible interface at the same time.
It is incorrect to make a driver "select DM_MMC_OPS".
While we are here, add "depends on OF_CONTROL" as well because this
driver can be configured only by Device Tree.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
callback function should be moved into sdhci_ops struct.
Other controller can use these ops for controlling clock or their own
specific register.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Add the s5p_set_clock function.
It's not good that "set_mmc_clk" is assigned directly.
In future, it should be changed to use the clock framework.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
This code is used for only pic32_sdhci controller.
To remove the "#ifdef", moves to pic32_sdhci.c.
And use the get_cd callback function.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Buswidth is depeneded on Hardware schematic.
Evne though host can support the 8bit buswidth, if hardware doesn't
support 8bit mode, it doesn't work fine.
So the buswidth mode selection leaves a matter in each SoC drivers.
On the contrary to this, hardware supports 8bit mode, but host doesn't
support it. then controller has to disable the MMC_MODE_8BIT.
(Host can check whether 8bit mode is supported or not, since V3.0)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Add option SYS_FSL_ERRATUM_ESDHC111, SYS_FSL_ERRATUM_ESDHC13,
SYS_FSL_ERRATUM_ESDHC135, SYS_FSL_ERRATUM_ESDHC_A001 to mmc Kconfig.
Move existing macros to related Kconfig.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate bk4r1]
Signed-off-by: Tom Rini <trini@konsulko.com>
This is a user-unconfigurable option that is selected by the
drivers that need to overwrite SDHCI IO memory accessors.
(BCM2835 SDHCI seems the only driver that needs to do so.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
While I moved the options, I also renamed them so that they are all
prefixed with MMC_SDHCI_.
This commit was created in the following steps.
[1] Rename with the following command
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_MMC_SDMA/CONFIG_MMC_SDHCI_SDMA/g
s/CONFIG_BCM2835_SDHCI/CONFIG_MMC_SDHCI_BCM2835/g
s/CONFIG_KONA_SDHCI/CONFIG_MMC_SDHCI_KONA/g
s/CONFIG_MV_SDHCI/CONFIG_MMC_SDHCI_MV/g
s/CONFIG_S5P_SDHCI/CONFIG_MMC_SDHCI_S5P/g
s/CONFIG_SPEAR_SDHCI/CONFIG_MMC_SDHCI_SPEAR/g
'
[2] create the Kconfig entries in drivers/mmc/Kconfig
[3] Move the options by the following command
tools/moveconfig.py -y MMC_SDHCI_SDMA MMC_SDHCI_BCM2835 \
MMC_SDHCI_KONA MMC_SDHCI_MV MMC_SDHCI_S5P MMC_SDHCI_SPEAR
[4] Sort drivers/mmc/Makefile for readability
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Move CONFIG_SDHCI to Kconfig and rename it to CONFIG_MMC_SDHCI.
My motivation for the rename is, ultimately, to make all the MMC
options prefixed with MMC_ and SDHCI options with MMC_SDHCI_,
like Linux.
This commit was created as follows:
[1] Rename the config option with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e 's/CONFIG_SDHCI/CONFIG_MMC_SDHCI/g'
[2] create the entry for MMC_SDHCI in drivers/mmc/Kconfig
[3] run "tools/moveconfig.py -y MMC_SDHCI"
[4] add "depends on MMC_SDHCI" to existing SDHCI driver entries
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Currently, CONFIG_MMC is not related to any other options by
"depends on" or "select". One of big advantages of using Kconfig
is automatic dependency tracking, but the current state is lacking
it. As the first step, make the existing MMC driver entries depend
on MMC.
This commit was created by the following steps:
[1] Run the following script:
--------------------8<--------------------
rm -f tmp.txt
for d in $(find . -path './configs/*_defconfig')
do
if grep -q -e 'CONFIG_MSM_SDHCI=y' $d ||
grep -q -e 'CONFIG_ATMEL_SDHCI=y' $d ||
grep -q -e 'CONFIG_ROCKCHIP_DWMMC=y' $d ||
grep -q -e 'CONFIG_SH_SDHI=y' $d ||
grep -q -e 'CONFIG_PIC32_SDHCI=y' $d ||
grep -q -e 'CONFIG_ZYNQ_SDHCI=y' $d ||
grep -q -e 'CONFIG_ROCKCHIP_SDHCI=y' $d ||
grep -q -e 'CONFIG_MMC_UNIPHIER=y' $d ||
grep -q -e 'CONFIG_SANDBOX_MMC=y' $d
then
echo CONFIG_MMC=y >> $d
echo ${d#./configs/} >> tmp.txt
fi
done
tools/moveconfig.py -y -s -d tmp.txt
rm tmp.txt
--------------------8<--------------------
[2] surround MMC driver entries with "if MMC" and "endif"
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Commit 7a777f6d6f ("mmc: Add generic Kconfig option") created
a Kconfig entry for this option without any actual moves, then
commit 44c798799f ("sunxi: Use Kconfig CONFIG_MMC") moved
instances only for SUNXI.
We generally do not like such partial moves. This kind of work
is automated by tools/moveconfig.py, so it is pretty easy to
complete this move.
I am adding "default ARM || PPC || SANDBOX" (suggested by Tom).
This shortens the configs and will ease new board porting.
This commit was created as follows:
[1] Edit Kconfig (remove the "depends on", add the "default",
copy the prompt and help message from Linux)
[2] Run 'tools/moveconfig.py -y -s -r HEAD MMC'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Remove the entire spear_sdhci.c file.
There is no use case. This is dead codes.
Also there is no place to call "spear_sdhci_init()" anywhere.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Palmas driver assumes it is always TPS659xx regulator on all DRA7xx based
boards to enable mmc regulator. This is not true always like in case of
DRA71x-evm. So get this information based on the board.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Delete omap4_vmmc_pbias_config from omap_hsmmc.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
CONFIG_AM57XX is just an unnecessary macro that is redundant given So,
remove the same instead of spreading through out the u-boot source
code and getting in the way to maintain common code for DRA7x family.
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add new configuration option CONFIG_MMC_TINY which strips away all
memory allocation within the MMC code and code for handling multiple
cards. This allows extremely space-constrained SPL code use the MMC
framework.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
If debug() is not used, then the whole content of debug(...) will
be removed by the preprocessor, which will result in the following
warning. This patch adds __maybe_unused annotation to fix this.
drivers/mmc/mmc.c: In function ‘mmc_init’:
drivers/mmc/mmc.c:1685:11: warning: variable ‘start’ set but not used [-Wunused-but-set-variable]
unsigned start;
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Add new command that provides possibility to enable the
background operations handshake functionality
(BKOPS_EN, EXT_CSD byte [163]) on eMMC devices.
This is an optional feature of eMMCs, the setting is write-once.
The command must be explicitly taken into use with
CONFIG_CMD_BKOPS_ENABLE.
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
At sdhci_get_config(), there was wrong condition to check pimux
id, so this patch fixes to check proper pinmux id.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
The sun8i SoCs also have a 8 bits capable MMC2 controller. Enable the
support for those too.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Some eMMC will fail at the first switch, but would succeed in a subsequent
one.
Make sure we try several times to cover those cases. The number of retries
(and the behaviour) is currently what is being used in Linux.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Due to the peripheral and generated clock driver improvement,
remove the unnecessary clock calling.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
If vmmc didn't supply, we didn't know which card didn't supply vmmc.
And changed from "put" to "debug".
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Now that CONFIG_BLK and CONFIG_MMC_OPS are enabled by default with
CONFIG_DM_MMC, the DWMMC driver on the socfpga platform fails at
runtime.
This adds the missing fields in the driver declaration.
Signed-off-by: Sylvain Lesne <lesne@alse-fr.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This pathc is fixed the below thing.
If misaligned the cache range, Just flush to CACHLINE_SIZE.
"CACHE: Misaligned operation at range [7ae55b00, 7ae55b08]"
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
In device tree, there is vmmc-supply property for SD/MMC.
Introduce mmc_power_init function to handle vmmc-supply.
mmc_power_init will first invoke board_mmc_power_init to
avoid break boards which already implement board_mmc_power_init.
If DM_MMC and DM_REGULATOR is defined, the regulator
will be enabled to power up the device.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
These two options go together and it is best to do the conversion in one
step. So enable DM_MMC_OPS by default if DM_MMC is enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the generic error number instead of meaningless value.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
"host->version" isn't a SoC specific value.
It doesn't need to get in each SoC drivers.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Some arguments don't need to pass to dwmci_setup_cfg.
They are already included in dwmci_host structure.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch support the driver model for s5p_sdhci controller.
To support the legacy model, maintained the existing code.
Note: If use the Driver Model, it needs to modify the device-tree.
In future, will update the Device-tree and enable the configuratioin.
(CONFIG_BLK, CONFIG_DM_MMC and CONFING_DM_MMC_OPS)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
By default saveenv option is not supported for SPL. This patch
enable the support for save environment variable for SPL build.
Enable save environment support in SPL after setenv. By default
the saveenv option is not provided in SPL, but some boards need
this support in 'Falcon' boot, where SPL need to boot from
different images based on environment variable set by OS. For
example OS may set "reboot_image" environment variable to
"recovery" inorder to boot recovery image by SPL. The SPL read
"reboot_image" and act accordingly and change the reboot_image
to default mode using setenv and save the environemnt.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Simon Glass <sig@chromium.org>
change in v1:
- dropped SUPPORT, use CONFIG_SPL_SAVEENV
- updates the comments in mmc_private.h
Need to initialize mmc->dev when probe, or will met
"dev_get_uclass_priv: null device", when `mmc dev 1`.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that the standard clock/reset APIs are available for all Tegra SoCs,
convert the MMC driver to use them exclusively, and remove any references
to the custom Tegra-specific APIs.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Convert the Tegra MMC driver to DM_MMC. Support for non-DM is removed
to avoid ifdefs in the code. DM_MMC is now enabled for all Tegra builds.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
(swarren, fixed some NULL pointer dereferences, removed extraneous
changes, rebased on various other changes, removed non-DM support etc.)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
struct mmc_host is a Tegra-specific structure, but the name implies it's
something defined by core MMC code, which is confusing. Rename it to
struct tegra_mmc_priv to make its purpose more obvious. The new name is
also more appropriate for a DM driver private data structure, which will
be relevant later in this series.
Nothing needs access to this type except the MMC driver itself. Move the
definition into the driver C file.
Make sure all Tegra MMC functions are named tegra_mmc_*. Even though
they're all static, it's useful to have good naming so that symbol tables
are easy to interpret. A few functions aren't renamed by this patch since
they'll be deleted by a subsequent patch in this series.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The MMC driver will soon be converted to use standard clock/reset APIs,
and so the periph_id field in the MMC device priv struct will disappear.
Rework the implementation of pad_init_mmc() to rely on this; using the
device register address is a much more direct test anyway.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
pad_init_mmc() is performing an SoC-specific operation, using registers
within the MMC controller. There's no reason to implement this code
outside the MMC driver, so move it inside the driver.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Tegra MMC driver currently honors "sdhci" entries in /aliases. The
MMC core however uses "mmc" entries in /aliases. This difference will be
relevant once the Tegra MMC driver is converted to DM, and the MMC core
handles alias lookups. To avoid issues during that conversion, fix the
Tegra MMC driver and all Tegra DTs to use the same alias name as the MMC
core does.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Now, include/linux/errno.h is a wrapper of <asm-generic/errno.h>.
Replace all include directives for <asm-generic/errno.h> with
<linux/errno.h>.
<asm-generic/...> is supposed to be included from <asm/...> when
arch-headers fall back into generic implementation. Generally, they
should not be directly included from .c files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Add drivers/usb/host/xhci-rockchip.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
These functions can be much simpler by squashing lines for immediate
return.
For *_bind() callbacks, they will be a simple wrapper function of an
upper-level bind API.
For mmc_set_{boot_bus_width,part_conf}, they will be a wrapper of
mmc_switch().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
When DTO interrupt occurred, there are any remaining data still in FIFO
due to RX FIFO threshold is larger than remaining data. It also
causes that dwmmc didn't trigger RXDR interrupt, so is TX.
It's responsibility of driver to read remaining bytes on seeing DTO
interrupt.
Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
To SD, there is no erase group, then the value erase_grp_size
will be default 1. When erasing SD blocks, the blocks will be
erased one by one, which is time consuming.
We use AU_SIZE as a group to speed up the erasing.
Erasing 4MB with a SD2.0 Card with AU_SIZE 4MB.
`time mmc erase 0x100000 0x2000`
time: 44.856 seconds (before optimization)
time: 0.335 seconds (after optimization)
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Clemens Gruber <clemens.gruber@pqgruber.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Eric Nelson <eric@nelint.com>
Cc: Stephen Warren <swarren@nvidia.com>
Add function to read SD_STATUS information.
According to the information, get erase_timeout/erase_size/erase_offset.
Add a structure sd_ssr to include the erase related information.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Clemens Gruber <clemens.gruber@pqgruber.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Eric Nelson <eric@nelint.com>
Cc: Stephen Warren <swarren@nvidia.com>
No need for per-SoC adjustment for this parameter. It should be
determined by the slowest hardware. Currently, no board overrides
this CONFIG, so 3.2 sec is large enough. (If not, we can make it
even larger.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This CONFIG is not configurable since it is not guarded by #ifndef.
Nobody has complained about that, so there is no need to keep it as
a CONFIG option.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If CONFIG_BLK is enabled, add_sdhci() is never called. Move this
quirk handling to sdhci_setup_cfg(), which is now the central place
for hardware capability checks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If CONFIG_BLK is enabled, add_sdhci() is never called. Move this
quirk handling to sdhci_setup_cfg(), which is now the central place
for hardware capability checks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
"Hardware doesn't specify base clock frequency" may not be only the
error case of sdhci_setup_cfg(). It is better to print this where
the corresponding error is triggered.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If CONFIG_BLK is enabled, add_sdhci() is never called.
So, sdhci_reset() is not called, either. This is a problem for
my board as it needs the reset to start from a sane state.
Move the add_sdhci() call to sdhci_init(), which is visited
by both of the with/without CONFIG_BLK cases.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This is the state-of-the-art MMC driver implementation.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With the CONFIG_DM_MMC_OPS migration, the .set_ios callback can
return an integer now. Return an appropriate error value rather
than sudden death by BUG().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
No more reason to define this function above the ops structure.
Move it near the caller. Also, change its return type to void
because it never fails.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Catch up with the DM migration.
As struct dm_mmc_ops does not have .init callback, call the init
function directly from the probe function.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Tegra SDHCI binding dictates that the reseet name for the Tegra SDHCI
clock be "sdhci" not "sdmmc", and that the clock is accessed by index
rather than by name. Fix the Tegra186 DT and MMC driver to honor this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
BLANCHE is development board based on R-Car V2H SoC (R8A7792)
This commit supports the following periherals:
- SCIF, Ethernet, QSPI, MMC
Signed-off-by: Masakazu Mochizuki <masakazu.mochizuki.wd@hitachi.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Building w/ GCC v5.2, the SD card access is broken due to invalid data
in the response command reconstructed at the end of
sh_sdhci_get_response().
Add a memory barrier between the two main steps of this function to
ensure the resp[] table content is consistent before bits reordering.
This fix has been tested Ok on Porter board rev1.0 using v2016.03
release.
Signed-off-by: Yannick Gicquel <yannick.gicquel@iot.bzh>
To prevent the compiler error, split the checking condition whether
cfg->ops is NULL or not.
It's more clearly, because it's not included in mmc_config structure
when CONFIG_DM_MMC_OPS is disabled.
drivers/mmc/mmc_legacy.c: In function ‘mmc_create’:
drivers/mmc/mmc_legacy.c:118:31: error: ‘const struct mmc_config’ has no member named ‘ops’
drivers/mmc/mmc_legacy.c:118:58: error: ‘const struct mmc_config’ has no member named ‘ops’
make[1]: *** [drivers/mmc/mmc_legacy.o] Error 1
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When the MMC framework was added in u-boot, the mmc_go_idle was
added before mmc_send_op_cond_iter in function mmc_send_op_cond
annotating that some cards seemed to need this. Actually, we still
need to do this in function mmc_complete_op_cond for those cards.
This has been verified on Micron MTFC4GACAECN eMMC chip.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
structure member 'cd_inverted' of omap_hsmmc_data
is available only when OMAP_HSMMC_USE_GPIO is
defined.
When CONFIG_DM_MMC is defined, but not
CONFIG_OMAP_GPIO, this will cause build breakage
in omap_hsmmc driver of the sort:
CC drivers/mmc/omap_hsmmc.o
../drivers/mmc/omap_hsmmc.c: In function 'omap_hsmmc_ofdata_to_platdata':
../drivers/mmc/omap_hsmmc.c:1763:6: error: 'struct omap_hsmmc_data' has no member named 'cd_inverted'
priv->cd_inverted = fdtdec_get_bool(fdt, node, "cd-inverted");
^
Fix this by accessing cd_inverted only when
OMAP_HSMMC_USE_GPIO is defined.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Convert the driver to the driver model while retaining the existing
legacy code. This allows the driver to support boards that have
converted to driver model as well as those that have not.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tegra186 supports the new standard clock and reset APIs. Older Tegra SoCs
still use custom APIs. Enhance the Tegra MMC driver so that it can operate
with either set of APIs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Some code may want to read reg values from DT, but from nodes that aren't
associated with DM devices, so using dev_get_addr_index() isn't
appropriate. In this case, fdtdec_get_addr_size_*() are the functions to
use. However, "translation" (via the chain of ranges properties in parent
nodes) may still be desirable. Add a function parameter to request that,
and implement it. Update all call sites to default to the original
behaviour.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Squashed in build fix from Stephen:
Signed-off-by: Simon Glass <sjg@chromium.org>
We no longer need to set 'caps' as it's not passed to sdhci_setup_cfg
anymore.
Fixes: 14bed52d27 ("mmc: sdhci: remove the unnecessary arguments for
sdhci_setup_cfg")
Signed-off-by: Tom Rini <trini@konsulko.com>
When disabled CONFIG_MMC_SDMA, variable caps didn't use.
This patch fixes the compiler error for -Wunused-but-set-variable
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
This patch fixes data starvation by host timeout(HTO) error interrupt
which occurred under FIFO mode transfer on rk3036 board.
The former implement, the actual bytes were transmitted may be less than
should be. The size will still subtract value of len in case of there is
no receive/transmit FIFO data request interrupt.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
The former implement, dw_mmc will push and pop the redundant data to
FIFO, we should transfer it according to the real size.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Some arguments don't need to pass to sdhci_setup_cfg.
Generic variable can be used in sdhci_setup_cfg, and some arguments are
already included in sdhci_host struct.
It's enough that just pass the board specific things to sdhci_setup_cfg().
After removing the unnecessary arguments, it's more simpler than before.
It doesn't consider "Version" and "Capabilities" anymore in each SoC
driver.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
buswidth isn't used anywhere in sdhci_setup_cfg.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This "commit 429790026021d522d51617217d4b86218cca5750" is wrong.
SDHCI_QUIRK_NO_HISPD_BIT is for skipping to set CTRL_HISPD bit.
For example, Exynos didn't have CTRL_HISPD. But Highspeed mode
is supported.
(This quirks doesn't mean that driver didn't support the Highseepd mode.)
Note: If driver didn't support the Highspeed Mode, use or add the other
quirks.
After applied this patch, all Exynos SoCs are just running with 25MHz.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
It's nicer to see this:
=> mmc list
dwmmc@ff0c0000: 0
dwmmc@ff0f0000: 1 (eMMC)
than this:
=> mmc list
dwmmc@ff0c0000: 0dwmmc@ff0f0000: 1 (eMMC)
With the former, it's much clearer which mmc devices are on.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Use the generic error number instead of specific error number.
If use the generic error number, it can debug more easier.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
<asm-generic/errno.h> is already included in <errno.h>.
It can use <errno.h> instead of <asm-generic/errno.h>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is no data, it doesn't needs to wait for completing data transfer.
(It seems that it can be removed.)
Almost all timeout error is occured from stop command without data.
After applied this patch, I hope that we don't need to increase timeout value anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
The current timeout detection logic is not very nice; it calls
get_timer(start) in the while() loop, and then calls it again after
the loop to check if a timeout error happened.
Because of the time difference between the two calls of get_timer(),
the timeout detected after the loop may not be true.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Not like the mmc-legacy which the devnum starts from 1, it starts from 0
in mmc-uclass, so the device number should be (devnum + 1) in get_mmc_num().
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
It's no need to speed 10 seconds to wait the mmc device out from busy
status. 500 milliseconds enough.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Move zynq to the latest driver model support by enabling CONFIG_DM_MMC,
CONFIG_DM_MMC_OPS and CONFIG_BLK.
Signed-off-by: Simon Glass <sjg@chromium.org>
There are no places to call these functions.
It should be used the callback function.
Then it can be used as static functions.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rockchip rk3399 using arasan sdhci-5.1 controller.
This patch add the controller support to enable mmc device
with full driver-model support, tested on rk3399 evb board.
According to my test result, this driver should be OK,
the command "part list mmc 0" can result in a right output,
but all the mmc command failed like this:
=> mmc info
No MMC device available
Command failed, result=1
The result of get_mmc_num in cmd/mmc.c is always 0?
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
This does not have much impact on behavior, but makes code look more
more like Linux. The use of devm_ioremap() often helps to delete
.remove callbacks entirely.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Disable internal clock by clearing the internal
clock enable bit. This bit needs to be cleared too
when we stop the SDCLK for changing the frequency
divisor. This bit should be set to zero when the
device is not using the Host controller.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Now that we know that the BROM stores a value indicating the boot-source
at the beginning of SRAM, use that instead of trying to recreate the
BROM's boot probing.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
With a recent bunch of SD3.0 cards in our A20-based board we
experienced data transfer rates of about 250 KiB/s instead of 10 MiB/s
with previous cards from the same vendor (both 4 GB/class 10). By
increasing status register polling rate from 1 kHz to 1 MHz we were
able to reach the original transfer rates again. With the old cards
we now even reach about 16 MiB/s.
Signed-off-by: Tobias Doerffel <tobias.doerffel@ed-chemnitz.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add support for of-platdata with rk3288. This requires decoding the
of-platdata struct and setting up the device from that. Also the driver
needs to be renamed to match the string that of-platdata will search for.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is more correct to avoid touching the device tree in the probe() method.
Update the driver to work this way.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch support the driver mode for exynos dwmmc controller.
To support the legacy model, maintained the existing code.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
If there is not "samsung,bus-width" property, use the 4bit buswidth by
default.
Almost all Exnyos SoCs support at least 4bit buswidth.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Clean the unused and unnecessary codse.
This patch is one of them for preparing to use DM.
Because it's easy to maintain and combine DM after cleaning codes.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
PERIPH_ID_SDMMC4(131) is not continous value with PERIPH_ID_SDMMC0(75).
If there is no 'index' property in fdt, then dev_index should be
assigned to dev_id(Peripheral ID).
At this time, dev_index should be "56". It means Exynos SoC has "56"
numbers of DWMMC IP. To prevent this behavior, it needs to check the
maximum device index.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Removed #ifdef for OF_CONTROL.
It might use 'OF_CONTROL' by default.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This function have maintained for supporting Non-FDT.
Now, Almost all SoC are changed to fdt style.
So there are no that this function is called anywhere.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The driver model conversion for MMC has moved in small steps. The first step
was to have an MMC device (CONFIG_DM_MMC). The second was to use a child
block device (CONFIG_BLK). The final one is to use driver model for MMC
operations (CONFIG_DM_MMC_OP). Add support for this.
The immediate priority is to make all boards that use DM_MMC also use those
other two options. This will allow them to be removed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this code into separate functions so that it can be used from the uclass
also. Add static inline versions for when the option is disabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than having an #ifdef in the main mmc.c file, control this feature
from the Makefile by moving the code into its own file.
Signed-off-by: Simon Glass <sjg@chromium.org>
These private functions are used both in the driver-model implementation and
in the legacy code. Add them to the header.
Signed-off-by: Simon Glass <sjg@chromium.org>
MMC core expects (now) valid mmc->dev pointer.
During conversion in commit cffe5d86 not every driver was updated.
This patch fixes crash while accessing MMC on
boards using Qualcomm SDHCI controller.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Otherwise, ocassionally see errors like this:
Flashing sparse image at offset 2078720
Flashing Sparse Image
sdhci_send_command: Timeout for status update!
mmc fail to send stop cmd
write_sparse_image: Write failed, block #2181088 [0]
This does not affect the actual writing speed, which is controlled by
the default value:
CONFIG_SDHCI_CMD_DEFAULT_TIMEOUT
It only increases the retries when reading:
SDHCI_INT_STATUS
to avoid the timeout error.
Signed-off-by: Steve Rae <steve.rae@raedomain.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Introudce wp_enable. To check WPSPL, wp_enable needs to be set
to 1 in board code.
Take i.MX6UL for example, for some boards, they do not use WP singal,
so they does not configure USDHC1_WP_SELECT_INPUT, and its default
value is 0(GPIO1_IO02). However GPIO1_IO02 is muxed for i2c usage and
SION bit set. So USDHC controller can always get wp signal and WPSPL
shows write protect and blocks driver continuing. This is not what
we want to see, so add wp_enable, and if set to 0, just omit the
WPSPL checking and this does not effect normal working of usdhc
controller.
If wp-gpios is provided in dts, wp_enable is set to 1, otherwise 0.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The USDHC moves the 4 clock bits CARD_CLK_SOFT_EN, IPG_PERCLK_SOFT_EN,
HCLK_SOFT_EN, and IPG_CLK_SOFT_EN from sysctl register to vendorspec
register. The driver uses RSTA to replace the clock gate off
operation. But this is not a good solution because:
1. when using RSTA, we should wait this bit to clear by itself. This is not
implemeneted in the code.
2. After RSTA is set, it is recommended that the Host Driver reset the
external card and reinitialize it.
So in this patch, we change to use the vendorspec registers for these bits
operation.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When booting in eMMC fast boot, MMC host does not exit from
boot mode after bootrom loading image. So the first command
'CMD0' sent in uboot will pull down the CMD line to low and
cause errors.
This patch cleans the MMC boot register in "mmc_init" to put the
MMC host back to normal mode.
Also clear DLL_CTRL delay line settings at USDHC initialization
to eliminate the pre-settings from boot rom.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
These condition checking are wrong.
Original Author's intention might be "&" instead of "&&".
It can know whether receive or transmit data request with
BIT[4]/BIT[5] of RINTSTS register.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The following changes are made to the clock API:
* The concept of "clocks" and "peripheral clocks" are unified; each clock
provider now implements a single set of clocks. This provides a simpler
conceptual interface to clients, and better aligns with device tree
clock bindings.
* Clocks are now identified with a single "struct clk", rather than
requiring clients to store the clock provider device and clock identity
values separately. For simple clock consumers, this isolates clients
from internal details of the clock API.
* clk.h is split so it only contains the client/consumer API, whereas
clk-uclass.h contains the provider API. This aligns with the recently
added reset and mailbox APIs.
* clk_ops .of_xlate(), .request(), and .free() are added so providers
can customize these operations if needed. This also aligns with the
recently added reset and mailbox APIs.
* clk_disable() is added.
* All users of the current clock APIs are updated.
* Sandbox clock tests are updated to exercise clock lookup via DT, and
clock enable/disable.
* rkclk_get_clk() is removed and replaced with standard APIs.
Buildman shows no clock-related errors for any board for which buildman
can download a toolchain.
test/py passes for sandbox (which invokes the dm clk test amongst
others).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add initial support for NXP's S32V234 SoC and S32V234EVB board.
The S32V230 family is designed to support computation-intensive applications
for image processing. The S32V234, as part of the S32V230 family, is a
high-performance automotive processor designed to support safe
computation-intensive applications in the area of vision and sensor fusion.
Code originally writen by:
Original-signed-off-by: Stoica Cosmin-Stefan <cosminstefan.stoica@freescale.com>
Original-signed-off-by: Mihaela Martinas <Mihaela.Martinas@freescale.com>
Original-signed-off-by: Eddy Petrișor <eddy.petrisor@gmail.com>
Signed-off-by: Eddy Petrișor <eddy.petrisor@nxp.com>
Enable 8bit interface on HSMMC2 for am33xx to support 8bit eMMC chips.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
revert patch:
commit: 6b2221b008: mmc: Handle switch error status bit in MMC card status
to get eMMC working on shc board
Signed-off-by: Heiko Schocher <hs@denx.de>
In function check_and_invalidate_dcache_range(), there are incorrect
start address and end address of the dcache range calculated for
Layerscape platforms. This patch is to fix this issue.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Tegra186's MMC controller needs to be explicitly identified. Add another
compatible value for it.
Tegra186 will use an entirely different clock/reset control mechanism to
existing chips, and will use standard clock/reset APIs rather than the
existing Tegra-specific custom APIs. The driver support for that isn't
ready yet, so simply disable all clock/reset usage if compiling for
Tegra186. This must happen at compile time rather than run-time since the
custom APIs won't even be compiled in on Tegra186. In the long term, the
plan would be to convert the existing custom APIs to standard APIs and get
rid of the ifdefs completely.
The system's main eMMC will work without any clock/reset support, since
the firmware will have already initialized the controller in order to
load U-Boot. Hence the driver is useful even in this apparently crippled
state.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
When these functions are not compiled in, we still need to declare the
correct function signature to avoid a build warnings in SPL. Fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an emulation of an SD card to sandbox, allowing MMC to be used in tests.
The emulation is very simple, supporting only card detection and reading
test data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for enabling CONFIG_BLK with MMC. This involves changing a
few functions to use struct udevice and adding a MMC block device driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Binding an MMC device when CONFIG_BLK is enabled requires that a block
device be bound as a child of the MMC device. Add a function to do this.
The mmc_create() method will be used only when DM_BLK is disabled.
Add an unbind method also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Implement the functions in mmc_legacy.c for driver-model block devices, so
that MMC can use driver model for these. This allows CONFIG_BLK to be enabled
with DM_MMC.
Signed-off-by: Simon Glass <sjg@chromium.org>
This driver will require generic MMC and block-device support in a future
commit. To avoid test errors, make this change now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Instead of looking up the MMC device by number, just pass it in. This makes
it possible to use this function with driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the MMC subsystem maintains its own list of MMC devices. This
cannot work with driver model, which needs to maintain this itself. Move the
list code into a separate 'legacy' file. The core MMC code remains, and will
be shared with the driver-model implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
The MMC block device is contained within struct mmc. But with driver model
this will not be the case. Add a function to obtain the block device. We
can later implement this for CONFIG_BLK.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is defined after it is used. In preparation for making it
static, move it up a little. Also drop the printf() which should not appear
in a driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
This allows to drop annoying (char *) casts when setting the host
name of struct sdhci_host.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add request gpio for CD and WP gpios, so that the gpio can be
used for the respective purposes.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
omap_hsmmc driver directly typecasts fdt_addr_t to a pointer.
This is not strictly correct, as it gives a build warning when
fdt_addr_t is u64. So, use map_physmem for a proper typecasts.
This is inspired by commit 167efe01bc ("dm: ns16550: Use an address
instead of a pointer for the uart base")
drivers/mmc/omap_hsmmc.c: In function ‘omap_hsmmc_ofdata_to_platdata’:
drivers/mmc/omap_hsmmc.c:776:20: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
priv->base_addr = (struct hsmmc *)dev_get_addr(dev);
^
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The dwmmc.h include was forgotten during the migration of dwmmc
probing to DM. Since the shiny DM is in place now, remove this
relic of the past.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Support Driver Model for fsl esdhc driver.
1. Introduce a new structure struct fsl_esdhc_priv
2. Refactor fsl_esdhc_initialize which is originally used by board code.
- Introduce fsl_esdhc_init to be common usage for DM and non-DM
- Introduce fsl_esdhc_cfg_to_priv to build the bridge for non-DM part.
- The original API for board code is still there, but we use
'fsl_esdhc_cfg_to_priv' and 'fsl_esdhc_init' to serve it.
3. All the functions are changed to use 'struct fsl_esdhc_priv', except
fsl_esdhc_initialize.
4. Since clk driver is not implemented, use mxc_get_clock to geth
the clk and fill 'priv->sdhc_clk'.
Has been tested on i.MX6UL 14X14 EVK board:
"
=>dm tree
....
simple_bus [ + ] | `-- aips-bus@02100000
mmc [ + ] | |-- usdhc@02190000
mmc [ + ] | |-- usdhc@02194000
....
=> mmc list
FSL_SDHC: 0 (SD)
FSL_SDHC: 1 (SD)
"
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Cc: Hector Palacios <hector.palacios@digi.com>
Cc: Eric Nelson <eric@nelint.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Simon Glass <sjg@chromium.org>
Tested-By: Eric Nelson <eric@nelint.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support for SD/eMMC controller present on some Qualcomm Snapdragon
devices. This controller implements SDHCI 2.0 interface but requires
vendor-specific initialization.
Driver works in PIO mode as ADMA is not supported by U-Boot (yet).
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
The Allwinner A64 SoC is used in the Pine64. This patch adds
all bits necessary to compile U-Boot for it running in AArch64
mode.
Unfortunately SPL is not ready yet due to legal problems, so
we need to boot using the binary boot0 for now.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
[agraf: remove SPL code, move to AArch64]
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Some parts of the sunxi code cast explicitly between u32 values and pointers.
This is not a problem in practice, because all 64bit SoCs today only use the
lower 32 bits for their phyical address space. But we need to make sure that
the compiler is sure this is not an accident as well.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties. (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
send_cmd response is valid only when no error happened. If an error
occured, let mmc_send_cmd() print the return value to aid debugging.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Fixes:
drivers/mmc/bcm2835_sdhci.c: In function ‘bcm2835_sdhci_init’:
drivers/mmc/bcm2835_sdhci.c:181:17: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
When enable dcache on HiKey, we're running into MMC command timeouts
because our retry loop is now faster than the eMMC (or an external SD
card) can answer.
Increase the retry count to the same as the timeout value for status
reports.
The real fix is obviously to not base this whole thing on a cycle counter
but on real wall time, but that would be slightly more intrusive.
Signed-off-by: Alexander Graf <agraf@suse.de>
Boards using the TWL6030 regulator may not all use the LDOs the same way.
Some might also not use MMC1 at all, so VMMC would't have to be enabled.
This delegates TWL6030 MMC power initializations to board-specific functions,
that may still call twl6030_power_mmc_init for the default behavior.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Not every device has multiple MMC slots available, so it makes sense to enable
only the required LDOs for the available slots. Generic code in omap_hsmmc will
enable both VMMC and VAUX1, in doubt.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
The original name of this function is unclear. This patch renames this
CRC16 function to crc16_ccitt() matching its name with its
implementation.
To make the usage of this function more flexible, lets add the CRC start
value as parameter to this function. This way it can be used by other
functions requiring different start values than 0 as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is a device number, and we want to use 'dev' to mean a driver model
device. Rename the member.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Rename three partition functions so that they start with part_. This makes
it clear what they relate to.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Use 'struct' instead of a typdef. Also since 'struct block_dev_desc' is long
and causes 80-column violations, rename it to struct blk_desc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
This driver implements platform specific glue and fixups for
PIC32 internal SDHCI controller.
Signed-off-by: Andrei Pistirica <andrei.pistirica@microchip.com>
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
According to SD spec, CMD12, CMD52 for writing I/O abort in CCCR need
to be set an Abort command type when they are sent. So, we remove all
chip-specific #ifdefs and make it available for all platforms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The MMC spec says "It is strongly recommended for hosts to implement
more than 500ms timeout value even if the card indicates the 250ms
maximum busy length." Even the previous value of 300ms is known to
be insufficient for some cards. So, increase the timeout to 500ms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add quirk to disable high speed incase the high
speed was broken.This solves the issue where the
the controller is used in High Speed Mode and the
the hold time requirement for the JEDEC/MMC 4.41
specification is NOT met.
This timing issue is not on all boards and hence
provided config option to enable it when required.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Emil Lenchak <emill@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Clear high speed bit if it was not supported by
the driver.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Emil Lenchak <emill@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove hardcoded value zero as min frequency and
use config option CONFIG_ZYNQ_SDHCI_MIN_FREQ
defined in board config
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Timing issue occurs on eMMC not only when modifying the frequency but
also for all the switch command(CMD6). According to the MMC spec waiting
8 clocks after a switch command would be the thing to do.
This patch allows fixing CPU hang observed when trying to changing the
bus width on a eMMC on SAMA5D4.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Marek Vasut <marex@denx.de> # on DENX MA5D4EV
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Andreas Bießmann <andreas.devel@googlemail.com> # on atngw100
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
[fixed minor checkpatch warning]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
At present we use the same peripheral ID for clocks and pinctrl. While this
works it is probably better to use the device tree clock binding ID for
clocks. We can use the clk_get_by_index() function to find this.
Update the clock drivers and the code that uses them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the pwrseq uclass to find a suitable power sequence for the MMC device.
If this is enabled in the device tree, we will pick it up automatically.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we add driver-model MMC devices in the order we find them. The
'alias' order is not honoured.
It is difficult to fix this for the case where we have holes in the
sequence. But for the common case where the devices are numbered from 0
without any gaps, we can add the devices to the internal data structures
in this order.
Signed-off-by: Simon Glass <sjg@chromium.org>
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously. Convert all of these to the correct SPDX-License-Identifier
tag.
Signed-off-by: Tom Rini <trini@konsulko.com>
the non-removable property point to sdcard before, it is wrong,
it must point to emmc, correct it.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
This will allow us to have multiple block device structs each referring
to the same eMMC device, yet different HW partitions.
For now, there is still a single block device per eMMC device. As before,
this block device always accesses whichever HW partition was most recently
selected. Clients wishing to make use of multiple block devices referring
to different HW partitions can simply take a copy of this block device
once it points at the correct HW partition, and use each one as they wish.
This feature will be used by the next patch.
In the future, perhaps get_device() could be enhanced to return a
dynamically allocated block device struct, to avoid the client needing to
copy it in order to maintain multiple block devices. However, this would
require all users to be updated to free those block device structs at some
point, which is rather a large change.
Most callers of mmc_switch_part() wish to permanently switch the default
MMC block device's HW partition. Enhance mmc_switch_part() so that it does
this. This removes the need for callers to do this. However,
common/env_mmc.c needs to save and restore the current HW partition. Make
it do this more explicitly.
Replace use of mmc_switch_part() with mmc_select_hwpart() in order to
remove duplicate code that skips the call if that HW partition is already
selected.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This will allow the implementation to make use of data in the block_dev
structure beyond the base device number. This will be useful so that eMMC
block devices can encompass the HW partition ID rather than treating this
out-of-band. Equally, the existence of the priv field is crying out for
this patch to exist.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present pci_mmc_init() does not correctly use the PCI function since the
list it passes is not terminated. The array size passed to pci_mmc_init() is
actually not used correctly. Fix this and adjust the pci_mmc_init() to scan
all available MMC devices.
Adjust this code to use the new driver model PCI API.
This should move over to the new MMC uclass at some point.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Table 41 of the JEDEC standard for eMMC says that bit 31 of
the command argument is obsolete when issuing the ERASE
command (CMD38) on page 115 of this document:
http://www.jedec.org/sites/default/files/docs/jesd84-B45.pdf
The SD Card Association Physical Layer Simplified Specification also
makes no mention of the use of bit 31.
https://www.sdcard.org/downloads/pls/part1_410.pdf
The Linux kernel distinguishes between secure (bit 31 set) and
non-secure erase, and this patch copies the macro names from
include/linux/mmc/core.h.
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Eric Nelson <eric@nelint.com>
Tested-by: Hector Palacios <hector.palacios@digi.com>
The low four bits of the SYSCTL register are reserved on the USDHC
controller on i.MX6 and i.MX7 processors, but are used for clocking
operations on earlier models.
Guard against their usage by hiding the bit mask macros on those
processors.
These bits are used to prevent glitches when changing clocks on
i.MX35 et al. Use the RSTA bit instead for i.MX6 and i.MX7.
>From the i.MX6DQ RM:
To prevent possible glitch on the card clock, clear the
FRC_SDCLK_ON bit when changing clock divisor value(SDCLKFS
or DVS in System Control Register) or setting RSTA bit.
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Hector Palacios <hector.palacios@digi.com>
Move the macro into the socfpga_dwmci_clksel().
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Marek Vasut <marex@denx.de>
[fix parenthesis in the sdmmc_mask]
There is no sprintf implementation in tiny-printf, so don't try to use
it when tiny-printf if used.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Calculate the minimum sd clock based on max clock. This will
be done by add_sdhci() if we pass minimum clock as zero.
It also does based on SD host contoller version.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Convert the SoCFPGA shim for registering the DWMMC driver to DM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
rk3036 mmc do not have internal dma, so we use fifo mode when read
and write data, we get the fifo mode and fifo depth property from
dts, pass to dw_mmc driver.
Signed-off-by: Lin Huang <hl@rock-chips.com>
emmc and sdcard have different register address, use non-removeable property
to distinguish them.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
some soc(rk3036 etc) use dw_mmc but do not have internal dma,
so we implement fifo mode to read and write data.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
the data transfer seem to long in the dwmci_send_cmd function,
so move this block as a separate funciton.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
socfpga_dw_mmc driver will obtain the drvsel and
smplsel value from device tree instead of definition
in config header file.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Marek Vasut <marex@denx.de>
zc1571 with silicon can operate on 200MHz maximum frequency. Setup this
frequency by default and fix setting for ep108.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Fix below compilation warings happening for hikey_defconfig
drivers/mmc/dw_mmc.c: In function ‘dwmci_set_idma_desc’:
drivers/mmc/dw_mmc.c:43:20: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
desc->next_addr = (unsigned int)desc + sizeof(struct dwmci_idmac);
^
drivers/mmc/dw_mmc.c: In function ‘dwmci_prepare_data’:
drivers/mmc/dw_mmc.c:61:35: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
dwmci_writel(host, DWMCI_DBADDR, (unsigned int)cur_idmac);
^
drivers/mmc/dw_mmc.c:73:9: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
(u32)bounce_buffer + (i * PAGE_SIZE));
^
CC drivers/mmc/hi6220_dw_mmc.o
drivers/mmc/hi6220_dw_mmc.c: In function ‘hi6220_dwmci_add_port’:
drivers/mmc/hi6220_dw_mmc.c:51:17: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
host->ioaddr = (void *)regbase;
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
The SDHCI is introduced by sama5d2, named as Secure Digital Multimedia
Card Controller(SDMMC). It supports the embedded MultiMedia Card (e.MMC)
Specification V4.41, the SD Memory Card Specification V3.0, and the SDIO
V3.0 specification. It is compliant with the SD Host Controller Standard
V3.0 specification.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
According to the SDHC specification, stopping the SD Clock is by setting
the SD Clock Enable bit in the Clock Control register at 0, instead of
setting all bits at 0.
Before stopping the SD clock, we need to make sure all SD transactions
to complete, so add checking the CMD and DAT bits in the Presen State
register, before stopping the SD clock.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
When detecting SDHC Adapter Card Type 2(SD/MMC Legacy Adapter Card),
enable EVDD automatic control via SDHC_VS. This could support SD card
IO voltage switching for UHS-1 speed mode.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
If adapter card type identification is supported for platform, we would
enable dat[4:7] for eMMC4.5 Adapter Card.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
commit b8e5b07225 "Powerpc: eSDHC: Fix mmc read write err in uboot of
T4240QDS board", T4160 also needs this fix.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The SD card detection depends on checking one pin state.
But the pin was configured after card was detected, which is wrong.
This commit fixes this, by moving call to pinmux before use the pin.
Tested-on: Odroid U3 and Odroid X2.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Global variables are bad. Get rid of this particular one, so we can
correctly instantiate multiple atmel mci interfaces, without having
them interfere with one another.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Instead of passing just the register area as a private data, introduce
a proper struct atmel_mci_priv structure instead. This will become useful
in the subsequent patch, where we eliminate the global variable from this
driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
[fix free()]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
After silencing the prints which were generated when reconfiguring the
clock of the SD/MMC bus, surprisingly, the driver stopped working such
that every attempt to use the SD/MMC bus caused the CPU to get totally
stuck hard. It turns out that the prints generated a short delay, which
was necessary for the CPU to reconfigure the clock without getting stuck.
Thus, this patch adds a short delay after the clock configuration instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
This driver generates clearly debugging prints when changing clock
speed, so silence those. Furthermore, the driver generates further
prints in case a command fails to complete. The later case woud be
useful, but for eMMC, command 8 can fail and it's not an error but
a part of the specification. Thus, make this debug() as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
[fix checkpatch warnings]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch adds esdhc support for ls1043ardb.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add MMC support for k2g
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
This driver did not yet configure the SDHCI MBUS bridge registers.
Without this and with CONFIG_MMC_SDMA enabled, mmc hangs at random
times. As DMA cannot complete correctly.
Tested on db-88f6820-gp eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Dirk Eibach <eibach@gdsys.cc>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Not all sunxi boards have an MMC embedded. Switching to the Kconfig option
will allow to enable or disable the support in each boards' defconfig.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add a generic Kconfig option for the CONFIG_MMC option that was used before
in the configuration headers.
Since all the architectures need to be converted to that first, depend on
an non-existent config option that will be extended with architectures that
use that option.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add more debug printfs in do_sdhci_init() for calls
that can potentially fail.
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
In case sdhci_get_config() or do_sdhci_init() fail, show
the error code that was returned.
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
exynos_mmc_init() always returns zero, so for the caller
it looks like it never fails.
Correct this by returning the error code of process_nodes().
For process_nodes() do something similar and return early
when do_sdhci_init() fails.
v2: Only fail in process_nodes() if we fail on all
available nodes.
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This makes sure that setting the host_caps in s5p_sdhci_core_init()
doesn't operate on potentially uninitialized memory.
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
In recent allwinner kernel sources the mmc/sdio clk-delay settings have
been slightly tweaked, and for sun9i they are completely different then
what we are using.
This commit brings us in sync with what allwinner does, fixing problems
accessing sdcards on some A33 devices (and likely others).
For pre sun9i hardware this makes the following changes:
-At 400Khz change the sample delay from 7 to 0 (first introduced in A31 sdk)
-At 50 Mhz change the sample delay from 5 to 4 (first introduced in A23 sdk)
-Above 50 MHz change the out delay from 2 to 1 (first introduced in A20 sdk)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The commit: d9dbb97be0
"mmc: dw_mmc: Zap endless timeout" removed endless loop waiting for end
of dw mmc transfer.
For some workloads - dfu test @ Odroid XU3 (sending 8MiB file) -
and SD cards (e.g. MicroSD Kingston 4GiB, Adata 4GiB)
the default timeout is to short.
The new value - 4 minutes (240 seconds) - is the same as the one used in
Linux kernel driver. Such fix should be good enough until we come up
with better fix for this issue.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@konsulko.com>
Tested-by: Przemyslaw Marczak <p.marczak@samsung.com>
Now that we have a new header file for cache-aligned allocation, we should
move the stack-based allocation macro there also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rework the driver to probe the MMC controller from Device Tree
and make it mandatory. There is no longer support for probing
from the ancient qts-generated header files.
This patch now also removes previous temporary workaround.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@konsulko.com>
During mmc initialize probe all devices with the MMC Uclass if build
with CONFIG_DM_MMC
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an MMC driver which supports RK3288, but may also support other SoCs.
It uses the Designware MMC device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some SoCs want to adjust the input clock to the DWMMC block as a way of
controlling the MMC bus clock. Update the get_mmc_clk() method to support
this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Originally a timeout value of 2 seconds was used regardless of the size
of data to be transfered. This prevented slow devices from working
correctly while there was no much gain for faster devices, e.g. it takes
3708ms for a transfer of uImage of size 1899008 bytes.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cleaning up order of include files by sorting them alphabetically
keeping in mind to leave common.h on top.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
We have flipped CONFIG_SPL_DISABLE_OF_CONTROL. We have cleansing
devices, $(SPL_) and CONFIG_IS_ENABLED(), so we are ready to clear
away the ugly logic in include/fdtdec.h:
#ifdef CONFIG_OF_CONTROL
# if defined(CONFIG_SPL_BUILD) && !defined(SPL_OF_CONTROL)
# define OF_CONTROL 0
# else
# define OF_CONTROL 1
# endif
#else
# define OF_CONTROL 0
#endif
Now CONFIG_IS_ENABLED(OF_CONTROL) is the substitute. It refers to
CONFIG_OF_CONTROL for U-boot proper and CONFIG_SPL_OF_CONTROL for
SPL.
Also, we no longer have to cancel CONFIG_OF_CONTROL in
include/config_uncmd_spl.h and scripts/Makefile.spl.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Currently implement always swap for big-endian value.
So doesn't work big-endian environment.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
We can calculate this. Add code to do this if it is not provided.
panto: prefix changed to dw_mmc to make things easier to grep
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Enable 8bit interface on HSMMC2 for am43xx to support 8bit eMMC chips.
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
The CMD(DAT) lines reset procedure described in the OMAP4(AM335x,
OMAP5, DRA7xx) TRMs is also necessary for AM43XX. Enable it in the
driver.
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
This patch adds the glue code for hi6220 SoC which has 2x synopsis
dw_mmc controllers. This will be used by the hikey board support
in subsequent patches.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The dw_mmc driver uses printf() in various places.
These bloat the code and cause problems for SPL. Use debug() where possible
and try to return a useful error code instead.
panto: Small rework to make it apply against top of tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
In case the data transfer failure happens, instead of returning
immediatelly, make sure the DMA is disabled, status register is
cleared and the bounce buffer is stopped.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@konsulko.com>
Endless timeouts are bad, since if we get stuck in one, we have no
way out. Zap this one by implementing proper timeout.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@konsulko.com>
The driver didn't stop the bounce buffer in case a data transfer
failed. This would lead to memory leakage if the communication
between the CPU and the card is unreliable. Add the missing call
to stop the bounce buffer.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@konsulko.com>
Derived from Tegra124, modified as appropriate during T210
board bringup. Cleaned up debug statements to conserve
string space, too. This also adds misc 64-bit changes
from Thierry Reding/Stephen Warren.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
DCIMVAC is upgraded to DCCIMVAC for the individual processor
(Cortex-A7) that the DCIMVAC is executed on.
We should follow the linux dma follow. Before DMA read, first
invalidate dcache then after DMA read, invalidate dcache again.
With the DMA direction DMA_FROM_DEVICE, the dcache need be
invalidated again after the DMA completion. The reason is
that we need explicity make sure the dcache been invalidated
thus to get the DMA'ed memory correctly from the physical memory.
Any cache-line fill during the DMA operations such as the
pre-fetching can cause the DMA coherency issue, thus CPU get the stale data.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Signed-off-by: Jason Liu <r64343@freescale.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
This patch extracts checking for valid SD card "eGON.BT0" signature from
`board_mmc_init` into function `sunxi_mmc_has_egon_boot_signature`.
Buffer for mmc sector is allocated and freed at runtime. `panic` is
triggered on malloc failure.
Signed-off-by: Daniel Kochmański <dkochmanski@turtle-solutions.eu>
CC: Roy Spliet <r.spliet@ultimaker.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
[hdegoede@redhat.com: Small bugfix to make it work for devs other then mmc0]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
`mmc_initialize` might be called multiple times leading to the mmc-controllers
being initialised twice, and initialising the `mmc_devices` list head twice
which may lead to memory leaks.
Signed-off-by: Daniel Kochmański <dkochmanski@turtle-solutions.eu>
CC: Roy Spliet <r.spliet@ultimaker.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
CC: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add a test to confirm that we can probe this device. Since there is no
MMC stack support in sandbox at present, this is as far as the test goes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add basic support for MMC, providing a uclass which can set up an MMC
device. This allows MMC drivers to move to using driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
While implementing SDIO/MMC SPL booting for the Marvell Armada 38x, the
following problem occured. The SPL runs in internal SRAM which is
the L2 cache locked to memory. When the MMC buffers now are located
on the stack (or bss), the SDIO controller (SDHCI) can't write into
this L2 cache memory.
This patch introduces a method to use a fixed buffer that will be
used for all transfers by defining CONFIG_FIXED_SDHCI_ALIGNED_BUFFER.
This way, the board can use this buffer address located in SDRAM
for all transfers. This solves this SPL problem on the A38x and
should only be used in the SPL U-Boot version.
Tested for SPL booting on Marvell Armada 38x DB-88F6820-GP board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
The loop counter based timeout detection does not work on the Armada
38x based board (DB-88F6820-GP). At least with dcache enabled a
timeout is detected. Without dcache enabled, the timeout does not
occur. Increasing the loop counter solves this issue. But a better
solution is to use a timer based timeout detection instead. This
patch now implements this timer based detection.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Patch 33fe2fb8df titled
"mmc: bcm283x: Remove get_timer_us() from mmc driver"
incorrectly replaced ad-hoc get_timer_us() function
with a plain get_timer(). The get_timer() operates in
mSec units instead of uSec though, which caused very
slow operation of the driver.
Restore the original behavior of the driver, but avoid
get_timer_us() and use timer_get_us() instead. The later
is part of the standard API.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jakub Kiciński <moorray3@wp.pl>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Jakub Kicinski <kubakici@wp.pl>
We want to see if the requested start or total block count are
unaligned. We discard the whole numbers and only care about the
remainder. Update the code to use div_u64_rem here and add a comment.
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Bernhard Nortmann <bernhard.nortmann@web.de>
Reported-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
The get_timer_us() function is something which is no longer
existing in case we use generic timer framework, so replace
it with get_timer().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Tyler Baker <tyler.baker@linaro.org>
If the mmc device is non-removable (as indicated by the device tree), set
the flag so that users of the device know.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
We need to clear the allocated memory explicitly as the included
struct sdhci_host has function pointers. Those are compared to NULL to
test if this (optional) feature is supported. Leaving them undefined let
u-boot jump to arbitrary memory.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Freescale eMMC44 adapter card uses Micron N2M400FDB311A3CF eMMC
memory. According to the silicon datasheet, secure erase timeout
is 600ms. So increase erase timeout value from 250ms to 600ms.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Timeout interrupt also work for response busy command(R1b) like
cmd38/cmd6. So need to set it accordingly. Current code only
set timeout for data command.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
High capacity support is not a host capability, but a device capability
that is queried via the OCR. The flag in the operating conditions
request argument can just be set unconditionally. This matches the Linux
implementation.
[panto] Hand merged and renumbering MMC_MODE_DDR_52MHz.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Starting part of device initialization sets the init_in_progress flag
only if the MMC card did not yet come to ready state and needs to continue
polling. If the card is SD or if the MMC card became ready quickly,
the flag is not set and (if using pre-initialization) the starting
phase will be re-executed from mmc_init function.
Set the init_in_progress flag in all non-error cases. Also, move flags
setting statements around so that the flags are not set in error paths.
Also, IN_PROGRESS return status becomes unnecessary, so get rid of it.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
The polling loops in sd_send_op_cond and mmc_complete_op_cond functions
check the ready flag state at the end of the loop, that is after executing
a delay inside the loop, which, in case of exiting with no error,
is not needed. Also, one of these loops, as well as the loop
in mmc_send_status, have the delay just before exiting on timeout
conditions.
Restructure all these loops to check the respective conditions before making
a delay for the next loop pass, and to appropriately exit without the delay.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Some MMC cards come to ready state quite quickly, so that the respective
flag appears to be set in mmc_send_op_cond already. In this case trying
to continue polling the card with CMD1 in mmc_complete_op_cond is incorrect
and may lead to unpredictable results. So check the flag before polling
and skip it appropriately.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
The previous change to use 'ocr' structure field for storing send_op_cond
command response also stopped using command response directly
outside of mmc_send_op_cond_iter(). Now it becomes possible to use
command structure in mmc_send_op_cond_iter() locally, removing a necessity
to pass it as an argument from the caller.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
The 'op_cond_response' field in mmc structure contains the response
from the last SEND_OP_COND MMC command while making iterational
polling of the card. Later it is copied to 'ocr' field, designed
to contain the OCR register value, which is actually the same
response from the same command. So, these fields have actually
the same data, just in different time periods. It's easier to use
the same 'ocr' field in both cases at once, without temporary using
of the 'op_cond_response' field.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
The SD clock could be generated by platform clock or peripheral
clock for some platforms. This patch adds peripheral clock
support for T1024/T1040/T2080. To enable it, define
CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add adapter card type identification support by reading
FPGA STAT_PRES1 register SDHC Card ID[0:2] bits. To use this function,
define CONFIG_FSL_ESDHC_ADAPTER_IDENT.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
[York Sun: resolve conflicts in README.fsl-esdhc]
Reviewed-by: York Sun <yorksun@freescale.com>
The driver-model gpio functions may return another value then -1 as error,
make the sunxi mmc code properly handle this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
sun6i and newer (derived) SoCs such as the sun8i-a23, sun8i-a33 and sun9i
have a various things in common, like having separate ahb reset control
registers, the SID living inside the pmic, custom pmic busses, new style
watchdog, etc.
This commit introduces a new hidden SUNXI_GEN_SUN6I Kconfig bool which can be
used to check for these features avoiding the need for an ever growing list
of "#if defined CONFIG_MACH_SUN?I" conditionals as we add support for more
"new style" sunxi SoCs.
Note that this commit changes the behavior of the gmac and hdmi code for
sun8i and the upcoming sun9i devices. This does not matter as sun8i does
not have gmac nor hdmi, and sun9i has new hardware-blocks for these so
the old code will not work there.
Also this is intentional as if a sun8i / sun9i variant which does use the
old hwblocks shows up then the GEN_SUN6I code paths will be the right ones
to use.
For completeness this also adds a SUNXI_GEN_SUN4I bool for A10/A13/A20.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Remove the quirk SDHCI_QUIRK_NO_CD as it is not
required.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change addresses to unsigned long to be compatible with 64-bit builds.
Regardless of fixing warnings, the device is still only 32-bit capable.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Change addresses to unsigned long to be compatible with 64-bit builds.
Regardless of fixing warnings, the device is still only 32-bit capable.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
SDHCI_HOST_CONTROL is a byte-sized register, so don't write to it
as if it were a long, as that would result in clobbering the three
registers following.
Signed-off-by: Matt Reimer <mreimer@sdgsystems.com>
Properly mask SELBASECLK by using an actual mask rather than the
number of bits to shift in order to create the mask.
Signed-off-by: Matt Reimer <mreimer@sdgsystems.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Add support of the DDR mode for eSDHC driver.
Enable it for i.MX6 SoC family only.
Signed-off-by: Volodymyr Riazantsev <volodymyr.riazantsev@globallogic.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Fix bus width switching from 8-bit mode down to 4-bit or 1-bit modes on
Samsung SoCs using SDHCI_QUIRK_USE_WIDE8. These SoCs report controller
version 2.0 yet they support 8-bit bus widths. If 8-bit mode was
previously enabled and then an operation like "mmc dev" caused a switch
back down to 4-bit or 1-bit mode, WIDE8 was left set, causing failures.
This problem was manifested by "mmc dev" timing out.
Signed-off-by: Matt Reimer <mreimer@sdgsystems.com>
Depending on the boot priority, the eMMC/SD cards,
can be initialized with the same numbers for each boot.
To be sure which mmc device is SD and which is eMMC,
this info is printed by 'mmc list' command, when
the init is done.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Before this commit, the mmc devices were always registered
in the same order. So dwmmc channel 0 was registered as mmc 0,
channel 1 as mmc 1, etc.
In case of possibility to boot from more then one device,
the CONFIG_SYS_MMC_ENV_DEV should always point to right mmc device.
This can be achieved by init boot device as first, so it will be
always registered as mmc 0. Thanks to this, the 'saveenv' command
will work fine for all mmc boot devices.
Exynos based boards usually uses mmc host channels configuration:
- 0, or 0+1 for 8 bit - as a default boot device (usually eMMC)
- 2 for 4bit - as an optional boot device (usually SD card slot)
And usually the boot order is defined by OM pin configuration,
which can be changed in a few ways, eg.
- Odroid U3 - eMMC card insertion -> first boot from eMMC
- Odroid X2/XU3 - boot priority jumper
By this commit, Exynos dwmmc driver will check the OM pin configuration,
and then try to init the boot device and register it as mmc 0.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Akshay Saraswat <akshay.s@samsung.com>
High Capacity (e)MMC cards work fine on sun4i / sun5i, and not having this
capability set causes u-boot to not recognize the eMMC on an Utoo P66 A13
tablet, so always set it thereby fixing this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Clksel value is exynos specific value.
It removed "clksel_val" into dwmci_host and created the
"dwmci_exynos_priv_data" structure for exynos specific data.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
"clksel_val" is assigned to property of mmc or defined value.
But it doesn't write at initial sequence.
There is a reason that get the wrong source-clock value.
This patch fixed it.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Some boards cannot do voltage negotiation but need to set the VSELECT
bit forcely to ensure it to work at 1.8V.
This commit adds CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT flag for this use.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This adds support to switch to 1.8V in case CMD11 succeeds.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Marek Vasut <marex@denx.de>
Since these board functions seem to be the same for all boards which use
FSP, move them into a common file. We can adjust this later if future FSPs
need more flexibility.
This creates a generic PCI MMC device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This results in a much more readable callgraph, because now they
can't be confused with the function having exactly the same name
in the generic mmc code.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The clocks on the A80 are hooked up slightly different, add support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Wait 1 second for the sdcard to respond, rather then waiting for
0xfffff milliseconds.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Wider bus widths (larger than default 1 bit) appeared in MMC standard
version 4.0. So, for MMC cards of any earlier version trying to change
the bus width (including ext_csd comparison) does not make any sense.
It may work incorrectly and at least cause unnecessary timeouts.
So, just skip the entire bus width related activity for earlier versions.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Tested-by: Alexey Brodkin <abrodkin@synopsys.com>
If all the commands switching an MMC card to 4- or 8-bit bus width fail,
and the bus width for the controller and the driver is still set
to default 1 bit, there is no need to send one more command to switch
the card to 1-bit bus width. Also, if the card or host controller do not
support wider bus widths, there is no need to send a switch command at all.
However, if one of switch commands succeeds, but the subsequent ext_csd
fields comparison fails, the card should be switched to some other bus width
(next in the list for the loop), or to default 1-bit bus width as a last
resort. That's why it would be incorrect to just remove the 1-bit bus width
case from the list, it should still be processed in some cases.
panto: Minor cosmetic edit removing superfluous parentheses.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Tested-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
This extends the mmcinfo hardware partition info output to show
partitions with write reliability enabled with the "WRREL" string.
If the partition does not have write reliability enabled the "WRREL"
string is omitted; this is analogous to the ehhanced attribute.
Example output:
Device: OMAP SD/MMC
Manufacturer ID: fe
OEM: 14e
Name: MMC16
Tran Speed: 52000000
Rd Block Len: 512
MMC version 4.41
High Capacity: Yes
Capacity: 13.8 GiB
Bus Width: 4-bit
Erase Group Size: 8 MiB
HC WP Group Size: 16 MiB
User Capacity: 13.8 GiB ENH WRREL
User Enhanced Start: 0 Bytes
User Enhanced Size: 512 MiB
Boot Capacity: 16 MiB ENH
RPMB Capacity: 128 KiB ENH
GP1 Capacity: 64 MiB ENH WRREL
GP2 Capacity: 64 MiB ENH WRREL
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
The eMMC partition write reliability settings are to be set while
partitioning a device, as per the eMMC spec, so changes to these
attributes needs to be done in the hardware partitioning API.
This commit adds such support.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
This adds an API to do hardware partitioning on eMMC devices. The
new mmc_hwpart_config() function does the partitioning in one go.
As the different attributes and partitioning options on eMMC may
be interdependent validation has to be done based on the complete
partitioning configuration. The function accepts three modes:
- MMC_HWPART_CONF_CHECK: just validates that the configuration
is valid.
- MMC_HWPART_CONF_SET: validates and sets all the fields in
EXT_CSD but without setting the "partitioning completed" bit,
and thus is reversible.
- MMC_HWPART_CONF_COMPLETE: does everything and is thus not
reversible.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
The mmc_startup() function uses the ext_csd data even if reading it
from the mmc device failed. This bug was introduced in commit
bc897b1d4d. We now bail out if
reading it fails, this should not be a problem as ext_csd was
introduced in MMC 4.0 and this code is conditional on MMC >= 4.0.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
The eMMC spec says that partitioning is only effective after the
PARTITION_SETTING_COMPLETED is set in EXT_CSD (and a power cycle was done,
but that we cannot know). Thus the partition sizes and attributes should
be ignored when that bit is not set, otherwise the various capacities
are not coherent (e.g., the user data capacity will be that of the
unpartitioned device while partition sizes would be non-zero).
Prescence of non-zero partitioning data is nevertheless still used to
activate the high-capacity size definitions (EXT_CSD_ERASE_GROUP_DEF)
as it is necessary to set that to write any of the partitioning fields
in EXT_CSD, so having partitioning data means someone previously
activated that and we should keep it activated.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
Read the eMMC high capacity write protect group size at mmc device
initialization. This is useful to correctly partition an eMMC device,
as partitions need to be aligned to this size.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
The erase_grp_size in struct mmc is to be a size in 512-byte sectors
but the code used to compute it for eMMC when EXT_CSD_ERASE_GROUP_DEF is
enabled computed it as bytes, leading to erase sizes and alignment
much larger than what is actually required by the mmc device.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
This modification reads the size of the eMMC enhanced user data area
upon initialization of an mmc device, it will be used later by
mmcinfo.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
The eMMC spec mandates that the high-capacity group size definitions
should be enabled when the device is partitioned (by setting
ERASE_GROUP_DEF in EXT_CSD). The current test to determine when this is
required misses a few cases. In particular a device may have been
partitioned without setting the enhanced attribute on any partition
or partitioning may be completed without creating any extra partitions.
This change moves the code to set ERASE_GROUP_DEF to after reading
all partition information. It is also enabled when
PARTITIONING_SETTING_COMPLETED is set as it is necessary to enable
ERASE_GROUP_DEF before setting that bit, so it means that the user
previously switched to the high capacity definitions.
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
This extends the mmcinfo command's output to show which eMMC partitions
have the enhanced attribute set. Note that the eMMC spec says that
if the enhanced attribute is supported then the boot and RPMB
partitions are of the enhanced type.
The output of mmcinfo becomes:
Device: OMAP SD/MMC
Manufacturer ID: fe
OEM: 14e
Name: MMC16
Tran Speed: 52000000
Rd Block Len: 512
MMC version 4.41
High Capacity: Yes
Capacity: 13.8 GiB
Bus Width: 4-bit
User Capacity: 13.8 GiB ENH
Boot Capacity: 16 MiB ENH
RPMB Capacity: 128 KiB ENH
GP1 Capacity: 64 MiB ENH
GP2 Capacity: 64 MiB ENH
Signed-off-by: Diego Santa Cruz <Diego.SantaCruz@spinetix.com>
It does not make sense to make gpio_direction_input() return the gpio input
status. The return value of gpio_direction_input() is inconsistent if
CONFIG_DM_GPIO is defined.
And we don't need to call gpio_direction_input() int sunxi_mmc_getcd().
Just init the gpio once in mmc_resource_init() is enough.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
The sunxi mmc controller has both an internal clock divider, as well as
the divider in the mod0-clk for the mmc controller.
The internal divider cannot be used, as it conflicts with the setting of
clock sampling phases which is done in the mod0-clk, so it must be set to
0 (divide by 1).
For some reason while the kernel has had this correct from day one, the
u-boot sunxi mmc code has been using a fixed mod0-clk and setting its
internal divider depending on the desired speed. This is something which
we've inherited from the original Allwinner u-boot sources, but while this
has been fixed in Allwinner's own u-boot code at least for the A23 and later
upstream u-boot was still doing this wrong.
This commit fixes this, thereby also fixing mmc support not working reliable
on the A23 (which seems more sensitive to this) and possible also fixes some
other sunxi mmc issues.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Get about 40x faster access on SHEEVAPLUG MMC
Fix some SD type compatibility
Changes in v3:
- fix the HW_STATE (from linux mvsdio)
- review delays and timeouts
Changes in v2:
- increase number of loops
- remove initial delay
Changes in v1:
- review all loops, delays and timeouts
Signed-off-by: Gérald Kerma <drEagle@doukki.net>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The card_caps bit should denote the card capability to use DDR mode,
but we need the flag indicating that the DDR mode is active.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Block length for write and read commands is fixed to 512 bytes
when the card is in Dual Data Rate mode. If block length read from CSD
is different, make sure the driver will use correct length
in all further calculations and settings.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Since the driver doesn't work in 1.2V or 1.8V signaling level modes,
Dual Data Rate mode can be supported by the driver only if it is supported
by the card in regular 3.3V mode. So, check for a particular single
bit in card type field.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
If the MMC_MODE_DDR_52MHz flag is set in card capabilities bitmask,
it is never cleared, even if switching to DDR mode fails, and if
the controller driver uses this flag to check the DDR mode, it can
take incorrect actions.
Also, DDR related checks in mmc_startup() incorrectly handle the case
when the host controller does not support some bus widths (e.g. can't
support 8 bits), since the host_caps is checked for DDR bit, but not
bus width bits.
This fix clearly separates using of card_caps bitmask, having there
the flags for the capabilities, that the card can support, and actual
operation mode, described outside of card_caps (i.e. bus_width and
ddr_mode fields in mmc structure). Separate host controller drivers
may need to be updated to use the actual flags. Respectively,
the capabilities checks in mmc_startup are made more correct and clear.
Also, some clean up is made with errors handling and code syntax layout.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
if the card claims to be high capacity and the card
is partitioned the capacity shall still be read from
ext_csd SEC_COUNT even if the resulting capacity is
smaller than 2 GiB
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
If print_mmc_devices() was called with a '\n' separator (as done
for example by the "mmc list" command), it offset the 2-nd and
all subsequent lines by one space. Fixing this.
Signed-off-by: Lubomir Popov <l-popov@ti.com>
Boards using the TWL4030 regulator may not all use the LDOs the same way
(e.g. MMC2 power can be controlled by another LDO than VMMC2).
This delegates TWL4030 MMC power initializations to board-specific functions,
that may still call twl4030_power_mmc_init for the default behavior.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
[trini: Fix omap3_evm warning, add twl4030.h]
Signed-off-by: Tom Rini <trini@ti.com>
Renesas R-Mobile/R-Car ARM SoC of MMC has the same IP that are supported by
sh_mmcif. This adds support R-Mobile/R-Car ARM SoC with the setting of the
clock support.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Maximum value and the minimum value of clock for sh_mmcif instead by
base of MMC clock. This removes fixed clock, make the changes to be calculated
according to environment.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Use DIV_ROUND_UP and fls to simplify the code.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Not every device has multiple MMC slots available, so it makes sense to enable
only the required LDOs for the available slots. Generic code in omap_hsmmc will
enable both VMMC1 and VMMC2, in doubt.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
Some devices may use non-standard combinations of regulators to power MMC:
this allows these devices to provide a board-specific MMC power init function
to set everything up in their own way.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
just add a few ifdefs around because this
device is very similar to dra7xxx.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.
Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
The reset value of "uSDHCx_INT_STATUS_EN" register is changed to 0
on iMX6SX. So the fsl_esdhc driver must update to set the register,
otherwise no state can be detected.
Signed-off-by: Ye.Li <B37916@freescale.com>
for multi instance API we use struct fsl_esdhc_cfg to
pass the clock rate. Do not set f_max from global data,
since this is wrong for multi instance case.
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Switch the default CD GPIO polarity to active low.
The current hsmmc driver assumption that the CD GPIO is active high, but
in the real hardware, usually the opposite holds.
The usual SD card socket has a mechanical switch which is grounded as
soon as a card is inserted.
Of course there might be some board logic which inverts the signal, but
as far as current users are concerned, there is no such logic.
Current U-Boot users either not using the CD functionality, or have a
different way (e.g. external to SoC GPIO controller) for checking the
card presence.
This patch also brings the polarity assumption in line with the Linux
kernel and adds appropriate comments.
This patch also might spare issues once the TWL GPIO driver will be
converted to the DM.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
This is necessary for the device-model enabled builds to work properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Mostly automatic with:
sed -i -e 's/CONFIG_\(SUN[45678]I\)/CONFIG_MACH_\1/g' $(git grep -l CONFIG_SUN[45678]I)
followed by removing the relevant #defines from include/configs/sun?i.h by
hand.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The SD Card slot detection pin should be configured as input.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
The Allwinner A23 SoC has reset controls like the A31 (sun6i).
The FIFO address is also the same as sun6i.
Re-use code added for sun6i.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
sunxi SOCs can boot from both mmc0 and mmc2, detect from which one we're
booting, and make that one "mmc dev 0" so that a single u-boot binary can
be used for both the onboard eMMC and for external sdcards.
When we're booting from mmc2, we make it dev 0 because that is where the SPL
will load the tertiary payload (the actual u-boot binary in our case) from,
see: common/spl/spl_mmc.c, which has dev 0 hardcoded everywhere.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The mmc hardware on sun6i has an extra reset control that needs to
be de-asserted prior to usage. Also the FIFO address is different.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[wens@csie.org: use setbits_le32 for reset control, drop obsolete changes,
rewrite different FIFO address handling, add commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Allwinner A20/A23/A31's SD/MMC host support SDHC High Capacity feature.
Signed-off-by: Wills Wang <wills.wang.open@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add driver model support to this driver, while retaining support for the
legacy system. Driver model GPIO support is enabled with CONFIG_DM_GPIO
as usual.
Since gpio_is_valid() no longer exists, we can use the -EINVAL error
returned from gpio_request().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
This move makes is possible to use this header not only from kirkwood
platforms but from all Marvell mvebu platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
With driver model GPIOs must be requested before use. Make sure this is
done correctly.
(Note that the soft SPI part of universal is omitted, since this driver
is about to be replaced with a driver-model-aware version)
Signed-off-by: Simon Glass <sjg@chromium.org>
During rigorous testing of our latest update infrastructure I came
across quite consistent timeouts on certain eMMC parts (e.g. Hynix
H26M21001ECR) when writing big (e.g. in excess of 400 MB) file system
images:
MMC write: dev # 0, block # 40960, count 944128 ...
mmc_send_cmd_bounced: MMC Timeout
Interrupt status 0x00000001
Interrupt status enable 0xdfff003b
Interrupt signal enable 0xdfff0002
Present status 0x01870106
mmc write failed
Comparing the various data sheets I came across the following timeout
specification:
Secure Erase/TRIM Timeout=300ms*2*10=6000ms
Unfortunately empirical testing still failed albeit much more rarely.
Increasing the timeout to 8000ms made it finally disappear entirely.
This patch allows us writing various eMMC parts without seeing any
further issues.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Change this board to add a device tree.
This also adds a pinmux header file although it is not used as yet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Make the SoCFPGA MMC stub pick clock via the clock manager
frequency accessors instead of hard-coding the frequency.
Also fix calloc() misuse.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
The dw_mmc driver was responding to errors with debug(). Change that
to prinf()/puts() respectively so that any errors are immediately
obvious. Also adjust english in comments.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Chin Liang See <clsee@altera.com>
dw_mmc driver was responding to errors with debug(). Change that to
prinf so that any errors are immediately obvious. Also adjust english
in comments.
Signed-off-by: Pavel Machek <pavel@denx.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
After setting the bus width, the extended CSD register is read. Some selected
fields are compared with previously read extended CSD register fields. In this
comparison the EXT_CSD_ERASE_GROUP_DEF field is compared. But this field is
previously written under certain circumstances. And then the comparison fails.
Only compare read-only fields. Therefore compare field EXT_CSD_HC_WP_GRP_SIZE
instead of field EXT_CSD_ERASE_GROUP_DEF.
Signed-off-by: Mario Schuknecht <mario.schuknecht@dresearch-fe.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
In function mvebu_mmc_write notice command timeout. It is possible that a
command is done, but a timeout occurred.
Enable timeout in set bus function.
Set window registers. Without that I could not use the driver on a Kirkwood
88F6282 SoC.
Set high capacity and 52MHz driver feature.
Signed-off-by: Mario Schuknecht <mario.schuknecht@dresearch-fe.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The capacity and lba for an MMC device with part_num 0 reflects the
whole device. When mmc_switch_part() successfully switches to a
partition, the capacity is changed to that partition. As partition 0
does not physically exist, attempts to switch back to the whole device
will indicate an error, but the capacity setting for the whole device
must still be restored to match the partition.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Tested-by: Tom Rini <trini@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
if we set manually this bit on the eMMC card using mmc_switch(...),
we also have to set it within our (before read) internal structure
'ext_csd'.
Otherwise following checks on this will fail.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Wait data transfer till the data end bit other than the data block end
bit is set.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
This would be useful to start moving various config options.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
For LS1, esdhc is big-endian IP. Accessing the registers
should be in big-endian mode. So we use esdhc_read32()
to read Host controller capabilities register for LS1.
For LS1, when using CMD12, cmdtype need to be set to
ABORT, otherwise, next read command will hang.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Structure defining clock manager hardware was wrong, leading to
wrong registers being accessed and hang in MMC init.
This fixes structure to match hardware.
Signed-off-by: Pavel Machek <pavel@denx.de>
If the MCI IP version >= 0x300, it supports hight speed mode
option, this patch enable it.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The mode register is different between MCI IP version.
So, according to MCI IP version to set the mode register.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
To fix the clock divider calculation error when the controller
clock same as the operating frequency. This is known as bypass
mode. In this mode, the divider should be 0.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Implement SD driver for the S3C24xx family. This implementation
is currently only capable of using the PIO transfers, DMA is not
supported.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Seems like the controller doesn't support the flag. None of the hi-speed cards
I've tried could be read, while they successfully worked with the quirk enabled.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
This patch add Marvell kirkwood MVSDIO/MMC driver
and enable it for Sheevaplugs and OpenRD boards.
Signed-off-by: Gerald Kerma <drEagle@doukki.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Add missing prototypes for global functions and
make local functions static.
cc: panto@antoniou-consulting.com
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
The DMA code in sunxi_mmc.c is broken. mmc_trans_data_by_dma() allocates the
dma descriptors on the stack, and then exits while the dma transfer is in
progress, so the dma engine is reading stack memory which at that point may
be re-used. So far we've gotten away with this by luck, but recent u-boot
changes have shifted the stack start address by 16 bytes, which combined
with dma alignment now exposes this problem.
Since we end up just busy waiting for the dma engine anyway, this commit
fixes things by simply removing the dma code, resulting in smaller bug-free
code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
commit 18b06652cd "tools: include u-boot version of sha256.h"
unconditionally forced the sha256.h from u-boot to be used
for tools instead of the host version. This is fragile though
as it will also include the host version. Therefore move it
to include/u-boot to join u-boot/md5.h etc which were renamed
for the same reason.
cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Cleanup to balance malloc/free calls.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Rather than just returning -1 everywhere, try to return something
meaningful from mmc_select_hwpart(). Note that most other MMC functions
don't do this, including functions called from mmc_select_hwpart(), so
I'm not sure how effective this will be. Still, it's one less place with
hard-coded -1.
Suggested-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
On Mon, 2014-05-05 at 14:18 +0200, Stefan Roese wrote:
> > + case 1:
> > +#if CONFIG_MMC1_PG
> Are you sure that this is correct and shouldn't be:
>
> +#ifdef CONFIG_MMC1_PG
>
> ?
It's "correct" in so far as it works (the boards.cfg config stuff
#defines things to 1), but I think you are right that it isn't the
preferred style. But...
> A quick scan through this patch series shows that this define
> is not set at all. Perhaps its outdated? Or is it used to support
> some other sunxi SoC? Not sure, perhaps it should be removed for
> now.
...I had thought that it was to support some other board which wasn't
being upstreamed right now, so eventually useful and harmless for now,
but I've just checked and it isn't actually used by any of the boards in
u-boot-sunxi.git. So rather than fix it to use #ifdef lets drop it.
Rather than resend the entire series, here is v5.1 of this patch.
> Other than this please add my:
>
> Reviewed-by: Stefan Roese <sr@denx.de>
Thanks!
8<---------------------------------
>From 20704e35a41664de5f516ed0e02981ac06085102 Mon Sep 17 00:00:00 2001
From: Ian Campbell <ijc@hellion.org.uk>
Date: Fri, 7 Mar 2014 04:29:39 +0000
Subject: [PATCH v5.1 7/8] sunxi: mmc support
This adds support for the MMC controller on the Allwinner A20 (sun7i)
processor.
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Luke Leighton <lkcl@lkcl.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Wills Wang <wills.wang.open@gmail.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Cc: Aaron Maoye <leafy.myeh@allwinnertech.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: Tom Rini <trini@ti.com>
In 7168977 we made calls to check_and_invalidate_dcache_range()
conditional on !CONFIG_SYS_FSL_ESDHC_USE_PIO. Only define this function
in this case as well.
Signed-off-by: Tom Rini <trini@ti.com>
This enables specifying which eMMC HW partition to target for any U-Boot
command that uses the generic get_partition() function to parse its
command-line arguments.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch adds functions for read, write and authentication
key programming for the Replay Protected Memory Block partition
in the eMMC.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
MMC switch command for unsupported feature (e.g. bus width) sets a switch
error bit in card status. This bit should be checked, and, if it's set,
no access with new controller settings should be performed.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
When configure the fsl_esdhc driver to PIO mode by defining
"CONFIG_SYS_FSL_ESDHC_USE_PIO", the SD/MMC read and write will fail.
Two bugs in the driver to cause the issue:
1. The read buffer was invalidated after reading from DATAPORT register,
which should be only applied to DMA mode. The valid data in cache was
overwritten by physical memory.
2. The watermarks are not set in PIO mode, will cause according state not
be set.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Conflicts:
boards.cfg
Conflicts were trivial once u-boot-arm/master boards.cfg was
reformatted (commit 6130c146) to match u-boot/master's own
reformatting (commit 1b37fa83).
To reuse the code, added the s5p_sdhci_core_init function.
Before applied this patch, didn't use the 8-bit mode at exynos baord.
Because it didn't set "MMC_MODE_8BIT".
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Restore the platdata(property of dt) into host struct.
Then data's information is maintained and reused anywhere.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
If CONFIG_API is ever to be enabled on Tegra, this define must be set,
since api/api_storage.c uses it.
A couple of annoyting things about CONFIG_SYS_MMC_MAX_DEVICE
1) It isn't documented in README. The same is true for a lot of similar
defines used by api_storage.c.
2) It doesn't represent MAX_DEVICE but rather NUM_DEVICES, since the
valid values are 0..n-1 not 0..n.
However, I this patch does not address those shortcomings.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
T4240RDB board Specification
----------------------------
Memory subsystem:
6GB DDR3
128MB NOR flash
2GB NAND flash
Ethernet:
Eight 1G SGMII ports
Four 10Gbps SFP+ ports
PCIe:
Two PCIe slots
USB:
Two USB2.0 Type A ports
SDHC:
One SD-card port
SATA:
One SATA port
UART:
Dual RJ45 ports
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: fix CONFIG_SYS_QE_FMAN_FW_ADDR in T4240RDB.h]
Add support of loading image, binary for MMC and SPI during SPL boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Fix following compile warnings
fsl_esdhc_spl.c: In function 'mmc_boot':
fsl_esdhc_spl.c:35:10: warning: unused variable 'byte_num' [-Wunused-variable]
fsl_esdhc_spl.c:35:7: warning: unused variable 'i' [-Wunused-variable]
fsl_esdhc_spl.c:34:8: warning: unused variable 'val' [-Wunused-variable]
fsl_esdhc_spl.c:33:6: warning: unused variable 'blklen' [-Wunused-variable]
fsl_esdhc_spl.c:105:7: warning: 'tmp_buf' may be used uninitialized in this
function [-Wuninitialized]
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1. The Data timeout counter value in eSDHC_SYSCTL register is
not working as it should be, so add quirks to enable this
workaround to fix it to the max value 0xE.
2. Add CONFIG_SYS_FSL_ERRATUM_ESDHC111 to enable its workaround.
* Update of patch for change mmc interface by
Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The controller reset is performed now if command error occurs.
This commit adds the reset for the case of data related errors too.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Calculation of the timeout value should be based on actual clock value,
written to controller registers. Since mmc->tran_speed is either the
maximum allowed speed, or the preliminary value, that is be not yet
set to registers, the actual timeout, taken by the controller, based
on its clock settings, may be much longer than expected, based on
mmc->tran_speed value. In particular it happens at early initialization
stage, when typical value of mmc->tran_speed is 20MHz or 26MHz, while
actual clock setting, configured in the controller, is 400kHz.
It's more correct to use mmc->clock value for timeout calculation instead.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Some eMMC chips may need the RST_n_FUNCTION bit set to a non-zero value
in order for warm reset of the system to work. Details on this being
required will be part of the eMMC datasheet. Also add using this
command to the dra7xx README.
* Whitespace fix by panto
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
In the recent mmc cleanup, the mmc_host_is_spi macro was broken and
bfin_sdh.c had mmc->bus_width turned into mmc_bus_width(mmc), both of
which were incorrect.
Signed-off-by: Tom Rini <trini@ti.com>
The way that struct mmc was implemented was a bit of a mess;
configuration and internal state all jumbled up in a single structure.
On top of that the way initialization is done with mmc_register leads
to a lot of duplicated code in drivers.
Typically the initialization got something like this in every driver.
struct mmc *mmc = malloc(sizeof(struct mmc));
memset(mmc, 0, sizeof(struct mmc);
/* fill in fields of mmc struct */
/* store private data pointer */
mmc_register(mmc);
By using the new mmc_create call one just passes an mmc config struct
and an optional private data pointer like this:
struct mmc = mmc_create(&cfg, priv);
All in tree drivers have been updated to the new form, and expect
mmc_register to go away before long.
Changes since v1:
* Use calloc instead of manually calling memset.
* Mark mmc_register as deprecated.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Using an array is pointless; even more pointless (and scary) is using
sprintf to fill it without a format string.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Remove the in-structure ops and put them in mmc_ops with
a constant pointer to it.
This makes the mmc structure smaller as well as conserving
code space (in theory).
All in-tree drivers are converted as well; this is done in a
single patch in order to not break git bisect.
Changes since V1:
Fix compilation b0rked issue on omap platforms where OMAP_GPIO was
not set.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
This patch enables support for device tree for sdhci driver.
Non DT case is still supported.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add support for the Kona SDHCI found on Broadcom mobile SoCs.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>
With d6a320d we moved some clock externs out of blackfin_local.h and
into clock.h but now need to include <asm/clock.h> in more drivers to
avoid warnings.
Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Tom Rini <trini@ti.com>
The open and close mmc sub-commands implement a hard-coded set of values
specific to the SMDK5250 platform. Remove these commands as what they
did can be done instead with a series of mmc dev / bootpart / bootbus
commands instead now.
Cc: Amar <amarendra.xt@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Add a bootbus sub-command to the mmc command to allow for setting
the boot_bus_width, reset_boot_bus_width and boot_mode fields of
BOOT_BUS_WIDTH (EXT_CSD[177]).
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Add a partconf sub-command to the mmc command to allow for setting
the boot_ack, boot_partition and partition_access fields of
PARTITION_CONFIG (formerly BOOT_CONFIG, EXT_CSD[179]). Part of this
requires changing the check for 'part' from an strncmp to a strcmp, like
the rest of the sub-commands.
Cc: Andy Fleming <afleming@gmail.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
As per the below commit
"mmc: sdhci: add the quirk for broken r1b response"
(sha1: 3a6383207b)
need to add quirk SDHCI_QUIRK_BROKEN_R1B, when the
response type is R1b.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
This patch corrects the divider value written to CLKDIV register.
Since SDCLKIN is divided inside controller by the DIVRATIO value set
in the CLKSEL register, we need to use the same output clock value to
calculate the CLKDIV value.
as per user manual: cclk_in = SDCLKIN / (DIVRATIO + 1)
Input parameter to mmc_clk is changed to dwmci_host, since
we need the same to read DWMCI_CLKSEL register.
This improves the read timing values for channel 0 on SMDK5250
from 0.288sec to 0.144sec
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
U-Boot currently sets MMC cards' RCA register to 0. This value is
reserved according to the specification. Use a value of 1 instead, just
like the Linux kernel.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Tegra124's MMC controller is very similar to earlier SoC generations,
and can be supported by the same driver.
However, there are some non-backwards-compatible HW differences, and
hence a new DT compatible value must be used to describe the HW. This
patch updates the driver to support that new compatible value.
That said, the HW differences are only relevant when enabling certain
high-performance transfer modes. Since the driver is currently very
simple and doesn't enable those modes, we don't actually need to address
any of these HW differences in the code yet, hence the simple nature of
this patch.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The upper 4 data signals of esdhc are shared with spi flash.
So detect if the upper 4 pins are assigned to esdhc before
enable sdhc 8 bit width.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Card detection pin is ineffective on T4240QDS Rev1.0.
There are two cards can be connected to board.
1. eMMC card is built-in board, can not be removed. so
For eMMC card it is always there.
2. Card detecting pin is functional for SDHC card in Rev2.0.
This workaround force sdhc driver scan and initialize the card
regardless of whether the card is inserted or not in case Rev1.0.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
To add the DesignWare MMC driver support for Altera SOCFPGA. It
required information such as clocks and bus width from platform
specific files (SOCFPGA handoff files)
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The eMMC and the SD-Card specifications describe the optional SET_DSR command.
During measurements at our lab we found that some cards implementing this feature
having really strong driver strengts per default. This can lead to voltage peaks
above the specification of the host on signal edges for data sent from a card to
the host.
Since availability of a given card type may be shorter than the time a certain
hardware will be produced it is useful to have support for this command (Alternative
would be changing termination resistors and adapting the driver strength of the
host to the used card.)
Following proposal for an implementation:
- new field that reflects CSD field DSR_IMP in struct mmc
- new field for design specific DSR value in struct mmc
- board code can set DSR value in mmc struct just after registering an controller
- mmc_startup sends the the stored DSR value before selecting a card, if DSR_IMP is set
Additionally the mmc command is extended to make is possible to play around with different
DSR values.
The concept was tested on a i.MX53 based platform using a Micron eMMC card where the default
DSR is 0x0400 (12mA) but in our design 0x0100 (0x0100) were enough. To use this feature for
instance on a mx53loco one have to add a call to mmc_set_dsr() in board_mmc_init() after
calling fsl_esdhc_initialize() for the eMMC.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Fixup prints to show where the print is done from, and
a few minor formatting/grammar issues.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Bounce buffer implementation takes care of proper data buffer alignemt
and correct flush/invalidation of data cache at once so we no longer
depend on input data variety and make sure CPU and MMC controller deal
with expected data in case of enabled data cache.
Bounce buffer requires to add its definition (CONFIG_BOUNCE_BUFFER) in
board configuration, otherwise corresponding library won't be compiled
and linker will fail to build resulting executable.
Difference since v1 - fixed compile-time warning with type casting to
"void *":
Slight edit to remove UTF8 characters in the commit message.
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
====
passing argument 2 of 'bounce_buffer_start' discards 'const' qualifier
from pointer target type
====
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Amar <amarendra.xt@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Andy Fleming <afleming@gmail.com>
To enhance the SDMMC DesignWare driver to use calloc instead of
malloc. This will avoid the incident that uninitialized members
of mmc structure are later used for NULL comparison.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Faraday FTSDC021 is a controller which is compliant with
SDHCI v3.0, SDIO v2.0 and MMC v4.3.
However this driver is only verified with SD memory cards.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
CC: Andy Fleming <afleming@gmail.com>
Existing eSDHC SPL framework assumes booting from sd-image
with boot_format header which contains final u-boot Image
offset and size. No such header is present in case of
corenet devices like T1040 as corenet deivces use PBI-RCW
based intialization.
So, for corenet deives, SPL bootloader use values provided
at compilation time. These values can be defined in board
specific config file.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
If platform provides "host->fifoth_val" it will be used for
initialization of DWMCI_FIFOTH register. Otherwise default value will be
used.
This implementation allows:
* escape unclear and recursive calculations that are currently in use
* use whatever custom value for DWMCI_FIFOTH initialization if any
particular SoC requires it
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Amar <amarendra.xt@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Andy Fleming <afleming@freescale.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
dw-mmc.c is the general driver file.
So, remove the exynos specific code at dw-mmc.c.
Instead, exynos specific cod can be move into exynos-dw_mmc.c.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
T4240QDS eSDHC host capabilities reigster should have VS33 bit define.
Add quirk CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 to deal with capacity
missing
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
struct mmc should be clear to all '0' after malloc to avoid
unexpect variable value.
Like mmc->has_init = xxx.
In this case mmcinfo will believe the card had been initialized before
and skip the initialization.
Test on P5040 and T4240,
Error Log:
=> mmcinfo
Device: FSL_SDHC
Manufacturer ID: 0
OEM: 0
Name: Tran Speed: 0
Rd Block Len: 0
MMC version 0.0
High Capacity: No
Capacity: 0 Bytes
Bus Width: 0-bit
=>
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Signed-off-by: Xie Shaohui-B21989 <B21989@freescale.com>
Tested-by: Ryan Barnett <rjbarnet@rockwellcollins.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
eSDHC host controller has new register to support SD Spec 3.0.
And the according host controller version was Freescale eSDHC
Version 3.0.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
SMDK5420 has a new Security Management Unit added
for dwmmc driver, hence, configuring the control
registers to support booting via eMMC.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Old command timeout value was too small and it caused I/O errors which
led to uncompleted read/write/erase operations and filesystem errors.
Timeout adaptation fixes this issue.
Changes in sdhci_send_command() function:
- change timeout variable to static
- increase default command timeout to 100 ms
- add definition of max command timeout value,
which can be redefined in each board config file
- wait for card ready state for max defined time
if it doesn't exceed defined maximum or return COMM_ERR
Once successfully increased timeout value will be used in next function
call. This fix was tested on Goni, Trats, Trats2 boards by testing UMS
on MMC storage.
Changes v2:
- move global variable cmd_timeout into function sdhci_send_command()
- change condition "==" to ">=" when comparing time with timeout
- print information about timeout increasing and card busy timeout
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
To prevent the confusion, use the get_mmc_clk() instead of mmc_clk().
get_mmc_clk() is more exactly name.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
EXT_CSD_ERASE_GROUP_DEF is lost every time after a reset or
power off. Set it if device has enhanced partitions.
Signed-off-by: Oliver Metz <oliver@freetz.org>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The patch fixes the improper read and write of sdhci
host control register for sdma transfer.
The problem comes when reading and writing 1 byte long
host control register with the sdhci_readl() and
sdhci_writel(). The misuse of these functions overwrite
the value of the next registers which are in 4 bytes boundary.
This patch replaces four byte register read/write functions
with one byte read/write ones. Beside, it eliminates
unnecessary bit operation. i.e. or-ing zero against a variable.
Signed-off-by: Juhyun (Justin) Oh <Juhyun_Oh@sigmadesigns.com>
This fixes two issues:
* a descriptor was allocated for every block, while a descriptor can
take 8 blocks
* there was an off-by-one error in the descriptor preparation: there
were two last descriptors, one with length==0
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Andy Fleming <afleming@gmail.com>
In dwmci_prepare_data, the descriptors are allocated for DMA transfer.
These are allocated using the ALLOC_CACHE_ALIGN_BUFFER. This macro uses
the stack to allocate these descriptors. This becomes a problem if the
DMA transfer continues after the processor leaves the function in which
the descriptors were allocated.
Therefore, I have moved the allocated of the buffers up one level, to
dwmci_send_cmd(). The DMA transfer should be complete when leaving this
function.
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Andy Fleming <afleming@gmail.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
For SPL builds this is just dead code since we'll only need to read.
Eliminating it results in a significant size reduction for the SPL
binary, which may be critical for certain platforms where the binary
size is highly constrained.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
If we don't have CONFIG_SPL_LIBCOMMON_SUPPORT defined then stdio
& *printf functions are unavailable & calling them will cause a link
failure.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Enable 8-bit host capability for HSMMC2 and/or HSMMC3. CONFIG_HSMMC2_8BIT
(for OMAP4/5/DRA7xx) and/or CONFIG_HSMMC3_8BIT (for DRA7xx only) must be
defined in the board header if an 8-bit eMMC device is connected to the
corresponding port.
Fix the "No status update" error that appeared for eMMC devices by
inserting a 20 us delay between writing arguments and command. This
solution has been proposed by Michael Cashwell <mboards@prograde.net>.
A minor cosmetic fix in a comment as well.
Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
"mmc_send_cmd: timeout: No status update" error sometimes happens in
omap_hsmmc driver func mmc_send_cmd() when the MMC controller card
identification and selection sequence is executed for eMMC on OMAP4
boards.
It happens due to incorrect execution of CMD line reset procedure
for OMAP4. Because CMD(DAT) lines reset procedures are slightly
different for OMAP3 and OMAP4(AM335x,OMAP5,DRA7xx).
According to OMAP3 TRM:
Set SRC(SRD) bit in MMCHS_SYSCTL register to 0x1 and wait until
it returns to 0x0.
According to OMAP4(AM335x,OMAP5,DRA7xx) TRMs, CMD(DATA) lines reset
procedure steps must be as follows:
1. Initiate CMD(DAT) line reset by writing 0x1 to SRC(SRD) bit in
MMCHS_SYSCTL register (SD_SYSCTL for AM335x).
2. Poll the SRC(SRD) bit until it is set to 0x1.
3. Wait until the SRC(SRD) bit returns to 0x0
(reset procedure is completed).
Unfortunately, at present omap_hsmmc driver has support only for
OMAP3. And as result step #2 is missing for OMAP4(AM335x,OMAP5,DRA7xx).
This sometimes leads to the fact that the waiting loop which is
required in step #3 does not executed, because SRC bit does not set
yet (at the moment of checking a condition of a loop execution).
And as a result this can cause to timeout error when sending a
next command.
In the particular case (working with eMMC witch do not respond to
some SD specific command) due to incorrect reset sequence after
command SD_CMD_SEND_IF_COND which finished with CTO flag within
64 clock cycles, the next command MMC_CMD_APP_CMD leads to a
timeout error within 1s.
So, extend CMD(DATA) lines reset procedure in func
mmc_reset_controller_fsm() by adding the missing step #2 for
OMAP4+/AM335x boards.
Signed-off-by: Oleksandr Tyshchenko <oleksandr.tyshchenko@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Do not call a memset for unused variable backup every time.
Remove unused variable from function.
Signed-off-by: Oleksandr Tyshchenko <oleksandr.tyshchenko@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Samsung SoC is supported the WIDE8, even if Controller version is v2.0.
So add the SDHCI_QUIRK_USE_WIDE8 for Samsung-SoC.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Enable support for high-capacity eMMC and MMC cards. The MXS MMC
driver has no problem with those.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Amaury Pouly <amaury.pouly@gmail.com>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
This patch cleans up license header in these files:
board/freescale/p1022ds/spl.c
drivers/mmc/fsl_esdhc_spl.c
drivers/mtd/spi/fsl_espi_spl.c
Signed-off-by: York Sun <yorksun@freescale.com>
The code from the internal on-chip ROM. It loads the final uboot image
into DDR, then jump to it to begin execution.
The SPL's size is sizeable, the maximum size must not exceed the size of L2
SRAM. It initializes the DDR through SPD code, and copys final uboot image
to DDR. So there are two stage uboot images:
* spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that
ddr spd code can get the interleaving mode setting in env. It loads
final uboot image from offset 96KB.
* final uboot image, size is variable depends on the functions enabled.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
The FTSDC010_DCR_FIFO_RST symbol is conditionally
defined in <faraday/ftsdc010.h> and it is available
available when CONFIG_FTSDC010_SDIO is enabled.
However the actual driver code unconditionally uses
the FTSDC010_DCR_FIFO_RST constant and this causes
build error if CONFIG_FTSDC010_SDIO is not enabled.
The following error happens when compiling for the
adp-ag101 board:
ftsdc010_mci.c: In function 'ftsdc010_request':
ftsdc010_mci.c:178: error: 'FTSDC010_DCR_FIFO_RST' undeclared (first use in this function)
ftsdc010_mci.c:178: error: (Each undeclared identifier is reported only once
ftsdc010_mci.c:178: error: for each function it appears in.)
The patch ensures that the FTSDC010_DCR_FIFO_RST
symbol gets used only if CONFIG_FTSDC010_SDIO is
defined.
Compile tested only.
Cc: Kuo-Jung Su <dantesu@faraday-tech.com>
Cc: Macpaul Lin <macpaul@andestech.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Reviewed-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Dealing with the sys ctrl register should touch only the
relevant bits and not accidently the whole register. On i.MX6,
the sys control register contains bits which shouldn't be reset to
0, e.g. SYS_CTRL[3-0] and IPP_RST_N (SYS_CTRL[23]).
Do this by read/modify/write instead of just a 32bit write.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Andy Fleming <afleming@freescale.com>
1. No contents of "asm/arch/clk.h" is used within "dw_mmc.c".
2. If arch doesn't have "asm/arch/clk.h" driver won't build.
Without mentioned inclusion dw_mmc driver could be built for arches
other than ARM. For ARM driver still builds without it.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Amar <amarendra.xt@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Fill the right command type when using CMD12 to stop data transfer.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
CC: Fleming Andrew-AFLEMING <AFLEMING@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
With CONFIG_SYS_64BIT_LBA, lbaint_t gets defined as a 64-bit type,
which is required to represent block numbers for storage devices that
exceed 2TiB (the block size usually is 512B), e.g. recent hard drives.
For some obscure reason, the current U-Boot code uses lbaint_t for the
number of blocks to read (a rather optimistic estimation of how RAM
sizes will evolve), but not for the starting address. Trying to access
blocks beyond the 2TiB boundary will simply wrap around and read a
block within the 0..2TiB range.
We now use lbaint_t for block start addresses, too. This required
changes to all block drivers as the signature of block_read(),
block_write() and block_erase() in block_dev_desc_t changed.
Signed-off-by: Sascha Silbe <t-uboot@infra-silbe.de>
Current DWMMC driver used to give FIFO underrun/overrun error every 3rd time
for mmc rescan command.
In current code FIFO_DEPTH is getting calculated after reading the default FIFOTH
register and extracting the RX_WMARK bits from it i.e (RX_WMARK = FIFO_DEPTH/2 -1).
Instead of storing the correct value, we were recalculating the FIFO_DEPT each
time which is not correct.
Based on "[PATCH V9 3/9] DWMMC: Initialise dwmci and resolve EMMC read write issues"
http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/160247
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Enhance the MMC core to calculate the size of each MMC partition, and
update mmc->capacity whenever a partition is selected. This causes:
mmc dev 0 1 ; mmcinfo
... to report the size of the currently selected partition, rather than
always reporting the size of the user partition.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
After waiting for the command completion event, the interrupt status
bits, that occured to be set by that time, are cleared by writing them
back. It is supposed, that it should be command related bits (command
complete and may be command errors).
However, in some cases the DMA already completes by that time before
the full transaction completes. The corresponding DINT bit gets set
and then cleared before even entering the loop, waiting for data part
completion. That waiting loop never gets this bit set, causing the
operation to hang. This is reported to happen, for example, for write
operation of 1 sector to upper area (block #7400000) of SanDisk Ultra II
8GB card.
The solution could be to explicitly clear only command related interrupt
status bits. However, since subsequent processing does not rely on
any command bits state, it could be easier just to remove clearing
of any bits at that point, leaving them all until all data processing
completes. After that the whole register will be cleared at once.
Also, on occasion, interrupts masking moved to before writing the command,
just for the case there should be no chance of interrupt between the first
command and interrupts masking.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Since commit 48e0b2bd (powerpc/esdhc: Correct judgement for DATA PIO mode)
we see mx6 systems to hang after doing a 'save' command.
Revert this commit since the original 'ifdef' logic from 7b43db92
(drivers/mmc/fsl_esdhc.c: fix compiler warnings) was the correct one.
Reported-by: Tapani Utriainen <tapani@technexion.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch fixes a bug related to mmc writes.
When doing fatwrites on an SD-Card, MMC bus problems can occur. Depending
on the size of the file, "MMC0: Bus busy timeout!" is reported, resulting
in an SD-Card that is no longer responding.
It appears to be, that set_cluster can be called with a size being zero.
That can be with a file that has a size being an exact multiple
(including 0) of the clustersize, but also for files that are smaller than
the size of one cluster.
The same problem occurs if the "mmc write" command is given with a block
count being 0.
By adding a check for the block count being zero in mmc_write_blocks
(drivers/mmc.c), this problem is solved.
Signed-off-by: Ruud Commandeur <rcommandeur@clb.nl>
Cc: Tom Rini <trini@ti.com>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Mats Karrman <Mats.Karrman@tritech.se>
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
CAP register don't have any information for 8-bit buswidth support
on 2.0 sdhci spec, only from 3.0 onwards bit[18] got this information.
Due to this misassignment in sdhci, mmc is setting 8-bit buswidth using
mmc_set_bus_width even if controller doesn't support.
Below change has code information.
"mmc: Properly determine maximum supported bus width"
(sha1: 7798f6dbd5)
Bug log: <mmc plus and emmc cards)
-------
zynq-uboot> mmcinfo
Error detected in status(0x208100)!
Device: zynq_sdhci
Manufacturer ID: fe
.....
So enable 8-bit support only for 3.0 spec using CAP and for below 3.0
assign mmc->host_caps = MMC_MODE_8BIT on respective platform driver
if host have a support.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch adds APIs to access(open / close) and to resize boot partiton of EMMC.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds FDT support for DWMMC, by reading the DWMMC node data
from the device tree and initialising DWMMC channels as per data
obtained from the node.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch enumerates dwmci and set auto stop command during
dwmci initialisation.
EMMC read/write is not happening in current implementation
due to improper fifo size computation. Hence modified the fifo size
computation to resolve EMMC read write issues.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The logic for the whether to configure for polling or DMA
was mistakenly reversed in this patch:
Commit 7b43db9211
drivers/mmc/fsl_esdhc.c: fix compiler warnings
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
CC: Sun Yusong-R58495 <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Faraday FTSDC010 is a MMC/SD host controller.
Although there is already a driver in current u-boot release,
which is modified from eSHDC and contributed by Andes Tech.
Its performance is too terrible on Faraday A36x SoC platforms,
so I turn to implement this new version of driver which is
10+ times faster than the old one.
It's carefully designed to be compatible with Andes chips,
so it should be safe to replace it.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Andy Fleming <afleming@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The mpc85xx repuires a special layout on the memory device that is
connected to the eSDHC controller interface. But the file spl_mmc.c
didn't handle this specfic case, there needs a special treatmen, in
the powerpc drictory. So, there is no longer to keep spl_mmc.c on
mpc85xx, CONFIG_SPL_FRAMEWORK is not set.
When CONFIG_SPL_MMC_SUPPORT is set and CONFIG_SPL_FRAMEWORK is not
set, there was an error in drivers/mmc/spl_mmc.c:
drivers/mmc/libmmc.o:(.got2+0x8): undefined reference to `spl_image'.
Now, the solution is to move the file "spl_mmc.c" to directory "common/spl".
Signed-off-by: Ying Zhang <b40530@freescale.com>
add mmc card support with atmel mci driver
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Using IP version for different setting
- Higher version supports 8bit mode
- Higher version bus width setting is different
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Since TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs,
rename twl6035_mmc1_poweron_ldo by a more generic palmas_mmc1_poweron_ldo
function.
Signed-off-by: Nishanth Menon <nm@ti.com>
TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs
Rename twl6035 to palmas to allow reuse across multiple current and
future platforms
As part of this change, change the CONFIG_TWL6035_POWER to
CONFIG_PALMAS_POWER and update usage of header file accordingly.
Signed-off-by: Nishanth Menon <nm@ti.com>
A malloc() followed by memset() can be simply replaced by calloc().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
If failed the add_host(), it is reasonable that return value of
add_sdhci().
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Without this additional delay, some eMMC don't negotiate properly bus width
Tested on:
- Toshiba THGBM2G8D8FBAIB
- Toshiba THGBM4G4D1HBAR
- Micron MTFC4GMVEA (the one giving the problem)
- Hynix H26M64002BNR
- SanDisk SDIN5E1-32G
Signed-off-by: Davide Bonfanti <davide.bonfanti@bticino.it>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Most of time that MMC driver spends on initializing a device is polling
OCR (operation conditions register). To decouple this polling loop,
device init is split into two parts: The first part fires the OCR query
command, and the second part polls the result. So the caller is now no
longer bound to the OCR-polling delay; he may fire the query, go
somewhere and then come back later for the result.
To use this, call mmc_set_preinit() on any device which needs this.
This can save significant amounts of time on boot (e.g. 200ms) by
hiding the MMC init time behind other init.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
log2 of the device block size serves as the shift value used to calculate
the block number to read in file systems when implementing avaiable block
sizes.
It is needed quite often in file systems thus it is pre-calculated and
stored in the block device descriptor.
Signed-off-by: Egbert Eich <eich@suse.com>
The number 512 appears quite a bit in the mmc code. Add a constant for this
so that it can be used here and in other parts of the code (e.g. SPL code
which loads from mmc).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@google.com>
block_read returns unsigned long, so it doesn't make sense to check for
< 0. and neither does marking the header structure as const and then
casting away the constness to load data into it.
Also cleanup some unneeded pointer casting while we're at it.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
Reviewed-by: Tom Rini <trini@ti.com>
The following headers are moved to a i.MX common location:
- regs-common.h
- regs-apbh.h
- regs-bch.h
- regs-gpmi.h
- dma.h
This way this header can be re-used also by other i.MX platforms.
For example the i.MX6 which will need it for the upcoming NAND
support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Support to check whether the SD3.0 or not.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Rommel Custodio <sessyargc@gmail.com>
eMMC vesrion is supported up to v4.5.
But bootloader isn't saw the exact eMMC version.
After applied this patch,
if use the mmcinfo command, then can see the exactly mmc version.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Rommel Custodio <sessyargc@gmail.com>
Rework the waiting for transfer completion loop condition
to continue waiting until both Transfer Complete and DMA End
interrupts occur. Checking of DLA bit in Present State register
looks not needed in addition to interrupts status checking,
so it can be removed from the condition. Also, DMA Error
condition is added to the list of data errors, checked in the loop.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
The cache should invalidate the read buffer for
the SD card interface after the transfer complete,
not command-complete.
Tested-by: Andrew Gabbasov <Andrew_Gabbasov@mentor.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
