AM654 has an arasan sdhci controller and a mmc phy attached to it.
Add basic support for K3 specific arasan sdhci controller.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The strobe dll code is ported from Linux Kernel:
drivers/mmc/host/sdhci-esdhc-imx.c
The comments are from the above file,
"For HS400 eMMC, there is a data_strobe line. This signal is generated
by the device and used for data output and CRC status response output
in HS400 mode. The frequency of this signal follows the frequency of
CLK generated by host. The host receives the data which is aligned to the
edge of data_strobe line. Due to the time delay between CLK line and
data_strobe line, if the delay time is larger than one clock cycle,
then CLK and data_strobe line will be misaligned, read error shows up.
So when the CLK is higher than 100MHz, each clock cycle is short enough,
host should configure the delay target. "
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Add HS400 support.
Selecting HS400 needs first select HS200 according to spec, so use
a dedicated function for HS400.
Add HS400 related macros.
Remove the restriction of only using the low 6 bits of
EXT_CSD_CARD_TYPE, using all the 8 bits.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The dev_get_priv(dev) is used twice in the probe function.
Replace the second invocation with priv variable.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for fetching the clock frequency both using the legacy
method in case clock framework is disabled as well as via the clock
framework if it is enabled. This allows for migration to the clock
framework on platforms which supports it while not breaking legacy
platforms. That said, the legacy method must be removed eventually.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
This commit enables support for Exynos Designware MMC driver based on DM.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
By convention for DM_MMC the host->priv is used to store struct udevice
*dev pointer.
Unfortunately, the legacy Exynos DW MMC code uses this field to
store pointer to dwmci_exynos_priv_data struct
Hence, we do need to get data in other way - namely by using container_of
when host pointer is present.
In this way the sdr_timing data is properly accessed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This commit prevents memory leak when this function is used with DM_MMC
as the struct dwmci_exynos_priv_data is already allocated by DM.
It is necessary for NON DM aware devices to allocate this struct first.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
As platform uses GPIOs for card detection, it's
simpler and more readable to use GPIO_ACTIVE_(LOW|HIGH)
in the gpio flags instead of using the cd-inverted
property.
Reported-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add missing clk_free() call in case of failure
when enabling the clock.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Config flag CONFIG_BLK becomes mandatory, update arm_pl180_mmci
to support this config.
This driver is used by STM32Fx and by Vexpress platforms.
Only STM32Fx are DM ready. No DM code is isolated and will be
removed easily when wexpress will be converted to DM.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The Allwinner H6 SoC has 3 MMC controllers like the ones in A64, with
the MMC2 come with the capability to do crypto by EMCE.
Add MMC support for H6. EMCE support is not added yet.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
This code is useful for testing the existance of devices that
do not have card detect capabilities. This breaks out the core
functionality and leaves the actual init logic and error reporting
in mmc_start_init().
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Correctly manage the SDMMC reset and card cycle power
to fully handle the power cycle added in the MMC uclass
and avoid issue with level-shifter with some uSDCARD.
3 states managed in driver:
1/ reset: SDMMC disable, signal HiZ
2/ power-cycle: SDMMC disable, signals drive to 0
3/ power-on: SDMMC enabled
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Commit dd27918c22 ("dm: mmc: sunxi: Add support for driver model")
only added the allwinner,sun5i-a13-mmc compatible string for this
driver. The DM initialisation code here also works with (at least) A10
and A20, so add the appropriate compatible strings as per Linux 4.17's
driver.
Tested on A10 Cubieboard and A20 pcDuino3 Nano with CONFIG_DM_MMC.
(A20 worked already, because sun7i-a20.dtsi specifies both the A13 and
A20 strings.)
Signed-off-by: Adam Sampson <ats@offog.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add support for loading U-Boot on the Broadcom 7445 SoC. This port
assumes Broadcom's BOLT bootloader is acting as the second stage
bootloader, and U-Boot is acting as the third stage bootloader, loaded
as an ELF program by BOLT.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Add code to reset all reset signals as in mmc DT node. A reset property
is an optional feature, so only print out a warning and do not fail if a
reset property is not present.
If a reset property is discovered, then use it to deassert, thus
bringing the IP out of reset.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Code around tuning_loop_counter variable expects to go below zero.
That's why this variable can't use unsigned type.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch fixes the mmc tuning command failures
when tuning pattern data needs to read back for
comparision against the expected bit pattern.
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add new compatible to the Uniphier SD driver for R8A77990 E3 SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch adds HS200 suuport for ZynqMP and enables
the same for ZC1751 DC1 board which has eMMC on it.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The compatible string of ftsdc010_mci.c is different from
the mmc driver in Linux Kernel. Modify it for consistency.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
SDMMC_CMD_CPSMEN bit is wrongly check and set in
SDMMC_ARG register instead of SDMMC_CMD register.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Some minor fixes for the Raspberry Pi:
- Fix SD writes on new sdhost controller
- Sanitize default load addresses, allowing for better payload placement
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=te7/
-----END PGP SIGNATURE-----
Merge tag 'signed-rpi-next' of git://github.com/agraf/u-boot
Patch queue for rpi - 2018-05-24
Some minor fixes for the Raspberry Pi:
- Fix SD writes on new sdhost controller
- Sanitize default load addresses, allowing for better payload placement
Convert CONFIG_SUPPORT_EMMC_RPMB to Kconfig. Split the command handling
from the underlying support and expose this through CMD_MMC_RPMB.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
The bcm2835 sdhost driver has a problem with "write multiple" commands.
It seems to boil down to the fact that the controller dislikes its FIFO
to get drained at the end of a block when a write multiple blocks command
is in flight.
The easy fix is to simply get rid of all the IRQ driven logic and make
the driver push as much data into the FIFO as it can. That way we never
drain and we never run into the problem.
Reported-by: Jan Leonhardt <jan@cyberdesigner.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
The check is necessary to avoid NULL pointer dereference.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Drop all the extra content from the MMC core, so that tiny MMC support
is really tiny, no fancy anything. That means the tiny MMC support does
only 1-bit transfers at default speed settings. Moreover, this patch
drops duplicate instance of struct mmc mmc_static, which wasted about
360 bytes. Furthermore, since MMC tiny supports only one controller
at all times, get rid of mallocating the ext csd backup and replace
it with static array. All in all, this patch saves ~4 kiB of bloat
from the MMC core, which on platforms with severe limitations can be
beneficial.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Fixup checkpatch.pl style warnings]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch adds support of SD3.0 for ZynqMP.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch reads the capabilities register1 and update the host
caps accordingly for mmc layer usage. This patch mainly reads
for UHS capabilities inorder to support SD3.0.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support to invoke any platform specific tuning
and delay routines if available.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support to disable clock if clk_disable
was set and then enable or set clock if the clock was changed
or clock was disabled when clock needs to be enabled.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch changed the datatype of variable "start" from uint to ulong
to work properly on 64-bit machines as well. Also the return type of
get_timer() function is ulong.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
On a socfpga_cyclone5 based board the SD card, was never powered up. For
other dw_mmc based SoCs dwmci_probe() is called in the platform specific
probe(). It seems this call is missing for socfpga_dw_mmc.
With this change DWMCI_PWREN is set by dmwci_init().
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add the debug message for checking the mmc clock status.
It's helpful to debug the controlling clock.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
mmc_set_clock() function has the disable argument as bool type.
When mmc_set_clock is called, it might be passed to "true" or "false".
But it's too confusion whether clock is enabled or disabled with only
"true" and "false".
To prevent the confusion, replace to MMC_CLK_ENABLE/DISABLE macro from
true/false.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
The 'SDHCI_QUIRK_NO_HISPD_BIT' is used wrong here. The purpose of this
quirk is to tell the sdhci-driver that the IP-core doesn't have a "high-
speed-enable" bit in its registers.
With this commit we change this to the correct quirk:
SDHCI_QUIRK_BROKEN_HISPD_MODE
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Some IP-core implementations of the SDHCI have different troubles on the
silicon where they are placed.
On ZYNQ platform for example Xilinx doesn't accept the hold timing of an
eMMC chip which operates in High-Speed mode and must be forced to
operate in non high-speed mode. To get rid of this
"SDHCI_QUIRK_BROKEN_HISPD_MODE" is introduced.
For more details about this refer to the Xilinx answer-recor #59999https://www.xilinx.com/support/answers/59999.html
This commit:
- doesn't set HISPD bit on the host-conroller
- reflects this fact within the host-controller capabilities
Upon this the layer above (mmc-driver) can setup the card correctly.
Otherwise the MMC card will be switched into high-speed mode and causes
possible timing violation on the host-controller side.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
sd_read_ssr returns 0, means no error.
Fixes: 5b2e72f32721484("mmc: read ssr only if MMC write support is enabled")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
Throughput tests have shown the sunxi_mmc driver to take over 10s to
read 10MB from a fast eMMC device due to excessive delays in polling
loops.
This commit restructures the main polling loops to use get_timer(...)
to determine whether a (millisecond) timeout has expired. We choose
not to use the wait_bit function, as we don't need interruptability
with ctrl-c and have at least one case where two bits (one for an
error condition and another one for completion) need to be read and
using wait_bit would have not added to the clarity.
The observed speedup in testing on a A31 is greater than 10x (e.g. a
10MB write decreases from 9.302s to 0.884s).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Mylène Josserand <mylene.josserand@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Staticize the function since it's only used in mmc.c .
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Tom Rini <trini@konsulko.com>
The size of SPL is hitting the limit (64KB) for uniphier_v7_defconfig.
When booting from SD/eMMC, obviously its clock has been properly set up
by the boot ROM. Acutually, no need to re-initialize the clock in SPL.
Using a clock driver would generalize the SoC specific code, but
solving the memory footprint problem would win.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
I need to differentiate the clock handling for uniphier-sd. Move it
to each driver's probe function from the tmio common code so that
renesas-sdhi will not be affected.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Odroid C2 fails to read from mmc with U-Boot v2018.03.
The change avoids a division by zero.
The fix was suggested by Jaehoon in
https://lists.denx.de/pipermail/u-boot/2018-January/318577.html
Reported-by: Vagrant Cascadian <vagrant@debian.org>
Suggested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
U-boot driver for sunxi-mmc uses PLL6, unlike linux kernel where
PLL5 is used, with clock rates respectively 600MHz and 768MHz.
Thus there are different phase degree steps - 24 for the kernel and
30 for u-boot.
In the kernel driver the phase is set 90 deg for output and 120 for
sample. Dividing by 30 will result values 3 and 4. Those are the
values set in the u-boot driver.
However, the condition defining delays is wrong. MMC core driver
requests clock of 52MHz, sunxi-driver sets clock of 50MHz, but
phase is set 30 deg for output and 120 deg for sample.
Apparently this works for most cards.
On A20-SOM204-EVB-eMMC there is eMMC card (KLMAG2GEND) which complains
about it. Maybe there is other boards with similar problem?
So the fix is to match delays for both u-boot and kernel.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add MMC DM and DT probing support into the SH MMCIF driver.
This patch abstracts out the common bits of the send command
and set ios functions, so they can be used both by DM and non
DM setups and adds the DM probe support.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
The mv_sdhci driver was not zeroing the sdhci_host structure it
allocates causing random access violations in parts of the mmc core
where the "ops" member pointers are checked and called if not NULL.
Signed-off-by: Matt Pelland <mpelland@starry.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Synchronize the naming with Linux, call the common code TMIO.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
The IP requires some time to recuperate after the IO pin
properties were changed. Add a delay to assure this.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Fix minor rebase omission, the else was missing which triggered
two accesses to the register on 64bit variant of the IP.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Make sure to wait for the command to complete altogether, including
the trailing 8 clock cycles. This prevents the driver for accidentally
writing the CMD register too fast before the previous command fully
completed.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
The HOST_MODE register must be set to 0 when the IP is operated in 16bit
mode, otherwise 16bit access to the data FIFO may fail.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
There are only a few registerse used in the 16bit mode which are
32bit internally. Special-case only those in the IO accessors and
always write both halves. Any other register access is protected
from accidentally overwriting neighboring register.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Add code for PHY tuning required for SDR104/HS200 support on Renesas RCar.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Export the matsu_sd_{read,write}l() common register access
functions, so that they can be used by other drivers sharing
the common code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Factor out the regulator handling into set_ios and add support for
selecting pin configuration based on the voltage to support UHS modes.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Handle the controller version even if quirks are set. The controller in
Renesas Gen3 SoCs does provide the version register, which indicates a
controller v10 and the controller does support internal DMA and /1024
divider.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Handle bus width 0 as 1-bit bus to assure valid content of
MATSU_SD_OPTION register WIDTH field.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
The DMA READ completion flag position differs on Socionext and Renesas
SoCs. It is bit 20 on Socionext SoCs and using bit 17 is a hardware bug
and forbidden. It is bit 17 on Renesas SoCs and bit 20 does not work on
them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
On the Renesas version of the IP, the /1 divider is realized by
setting the clock register [7:0] to 0xff instead of setting bit
10 of the register. Check the quirk and handle accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Add a quirk to identify that the controller is Renesas RCar variant
of the Matsushita SD IP and another quirk indicating it can support
Renesas RCar HS200/HS400/SDR104 modes.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Drop the ad-hoc DT caps parsing in favor of common framework function.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
The Renesas RCar Gen2 chips have a mix of 32bit and 16bit variants
of the IP. There is no DT property which allows discerning those,
so what Linux does is it checks the size of the register area and
if it is 0x100, the IP is 16bit, otherwise the IP is 32bit. Handle
the distinction the same way.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Certain instances of the SD IP require more elaborate digging
in the DT to figure out which variant of the SD IP is in use.
Allow explicit passing of the quirks into the probe function.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Add support for 16bit mutation of the Matsushita SD IP. Since some
registers are internally 32bit, the matsu_sd_{read,write}l() has
to special-case this 16bit variant a bit.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Drop useless check in matsu_sd_{read,write}q(), this is only ever
called to read the data from FIFO and only when 64bit variant of
the block is used anyway.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Add macros to generate the FIFO accessors, since the code is almost
the same with only minor differences. This is done in preparation
for adding 16bit variant of the IP.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Add Kconfig entry for the Renesas SDHI variant of the controller
and split the Makefile entries accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Factor out common code from the uniphier SD driver, change the prefix
of the functions from uniphier_sd_ to matsu_sd_ and create separate
renesas-sdhi.c driver. Thus far, all the code is still compiled when
CONFIG_UNIPHIER_MMC is selected and there is no functional change.
This patch is a preparation for further split of the SoC specific
parts of the Matsushita SD driver, used both on Uniphier and R-Car.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
In raspberrypi-firmware 7fdcd00e00a42a1c91e8bd6f5eb8352fe9358557 and
later start.elf now sets the EMMC clock to 200 MHz.
According to Phil Elwell in
https://github.com/raspberrypi/firmware/issues/953
the SDHost controller shares the core/VPU clock and doesn't use
the EMMC clock.
Use the core clock id when determining the frequency to allow
U-Boot to work with recent versions of raspberrypi-firmware.
Otherwise U-Boot hangs at:
U-Boot 2018.03 (Mar 14 2018 - 20:36:00 +1100)
DRAM: 948 MiB
RPI 3 Model B (0xa02082)
MMC: mmc@7e202000: 0, sdhci@7e300000: 1
Loading Environment from FAT...
Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Use dm_pci_map_bar function for BAR mapping. This has the advantage
of clearing BAR flags and and only accepting mapped memory.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
nsd32_mmc was created to support ftsdc010 dm.
It is not necessary to separate both, so merge it
to ftsdc010.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
Convert CONFIG_FTSDC010_SDIO to Kconfig.
So CONFIG_FTSDC010_SDIO can also be
removed from config_whitelist.txt.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
Only three defconfig(adp-ag101p_defconfig,
adp-ae3xx_defconfig, nx25-ae250_defconfig)
set CONFIG_FTSDC010=y. And they all also
enable CONFIG_DM_MMC. So the non-dm code
of ftsdc010 can be dropped now.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
ftsdc010 dm driver has been disable High-Speed mode
as default to work around Andes AE3XX platform's problem,
because of it does not support High-Speed mode in
commit id 73cd56b2df.
But other platforms or SoCs maybe support this function.
So High-Speed mode can be enabled from dts with
cap-mmc-highspeed or cap-sd-highspeed property.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
The Rockchip-specific SDHCI wrapper does not process the 'bus-width'
property in the SDHCI node. Consequently, the bus is always kept in
4bit mode, even if 8bit wide operation is available, supported and
requested in the DTS.
This change adds processing of the 'bus-width' property and sets the
host capability flag for an 8bit wide bus, if set to 8. As the logic
in sdhci.c does not support clearing the 4bit capability, we assume
that 4bit operation is always supported.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch adds "st,pin-ckin" support to activate sdmmc_ckin feature.
When using an external driver (a voltage switch transceiver),
it's advised to select SDMMC_CKIN feedback clock input to sample
the received data.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The hardware flow control functionality is used to avoid
FIFO underrun (TX mode) and overrun (RX mode) errors.
The behavior is to stop SDMMC_CK during data transfer and
freeze the SDMMC state machines.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
With CONFIG_DM_MMC the BananaPi does not detect SD cards.
The sunxi device trees use the cd-inverted property to indicate that
the card detect is inverted.
This property is documented in Linux kernel devicetree/bindings/mmc/mmc.txt
The property is not marked as deprecated.
A similar patch was posted by Tuomas but is in status "Changes Requested".
https://patchwork.ozlabs.org/patch/850377/
This patch is a stripped down version of his patch.
Suggested-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.
This commit moves the header code:
include/libfdt.h -> include/linux/libfdt.h
include/libfdt_env.h -> include/linux/libfdt_env.h
and replaces include directives:
#include <libfdt.h> -> #include <linux/libfdt.h>
#include <libfdt_env.h> -> #include <linux/libfdt_env.h>
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch added Kconfig support for CONFIG_ZYNQ_SDHCI_MIN_FREQ
and enabled it in respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch added Kconfig support for CONFIG_ZYNQ_SDHCI_MAX_FREQ
and enabled it in respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
mmc_of_parse() doesn't set a default value if none is available in DT.
In that case, use a default 52MHz clock rate.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some platforms don't have ADMA controllers. For those platforms, compiling
it out reduces the size of the binary by about 600 bytes.
Leaving the support in doesn't break things as the driver checks at runtime
if the ADMA2 controller is present.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This reduces the size of the binary by about 196 bytes.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The area for struct mmc can be allocated dynamically. It greatly reduces
the size of struct omap_hsmmc_plat. This is useful in cases where the board
level code declares one or two struct omap_hsmmc_plat because it doesn't
use the Driver Model.
This saves around 740 bytes for the am335x_evm SPL.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
MMC card with EXT_CSD_REV value 9 will trigger off-by-one
bug while accessing mmc_versions array. The patch fix that.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Add DT compatible strings for RCar Gen2 SoCs, so that this driver
can bind with them. Unlike Gen3, which uses 64bit FIFO, the Gen2
uses 16bit FIFO.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
If some configs are disabled, number of freqs array will not assigned to
correct value with bus_mode.
Synchornize the ordering with enum bus_mode in mmc.h.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
When using omap_hsmmc without the device model then the allocation
of mmc->priv ends up uninitialised.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
The correspondence between mmc versions as used in u-boot and the version
numbers reported in register EXT_CSD_REV is wrong for versions above and
including MMC_VERSION_4_41. All those versions were shifted by one:
real 4.5 hardware appeared to be MMC_VERSION_5_0.
Fix this by adding the missing version in the correspondence table.
Reported-by: eil Eilmsteiner Heribert <eil@keba.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
After settings the speed of the sd with the switch command, a check is
done to make sure that the new speed has been set. The current check has a
masking error: speed are encoded on 4 bits only.
Fix it by masking the upper bits.
This fixes a problem seen with QEmu emulating a vexpress-a15.
Reported-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Jonathan Gray <jsg@jsg.id.au>
I/O data lines of UHS SD card operates at 1.8V when in UHS speed
mode (same is true for eMMC in DDR and HS200 modes). Add support
to switch signal voltage to 1.8V in order to support
UHS cards and eMMC HS200 and DDR modes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
mmc core has defined a new parameter *clk_disable* to gate the clock.
Disable the clock here if *clk_disable* is set.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
When the clock is applied, compute the actual value of the clock. It may be
slightly different from the requested value (max freq, divisor threshold)
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The default configuration is usually working fine for the the HS modes.
Don't enforce the presence of a dedicated pinmux for the HS modes.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
AM572x SR1.1 requires different IODelay values to be used than that used
in AM572x SR2.0. These values are populated in device tree. Add
capability in omap_hsmmc driver to extract IOdelay values for different
silicon revision. The maximum frequency is also reduced when using a ES1.1.
To keep the ability to boot both revsions with the same dtb, those values
can be provided by the platform code.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The data manual of J6/J6 Eco recommends to set different IODELAY values
depending on the mode in which the MMC/SD is enumerated in order to
ensure IO timings are met.
Add support to parse mux values and iodelay values from device tree
and set these depending on the enumerated MMC mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Use the mmc_of_parse library function to populate mmc_config instead of
repeating the same code in host controller driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
>From OMAP3 SoCs (OMAP3, OMAP4, OMAP5, AM572x, AM571x), the DAT/CMD lines
reset procedure section in TRM suggests to first poll the SRD/SRC bit
until it is set to 0x1. But looks like that bit is never set to 1 and there
is an observable delay of 1sec everytime the driver tries to reset DAT/CMD.
(The same is observed in linux kernel).
Reduce the time the driver waits for the controller to set the SRC/SRD bits
to 1 so that there is no observable delay.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
According to errata i802, DCRC error interrupts
(MMCHS_STAT[21] DCRC=0x1) can occur during the tuning procedure.
The DCRC interrupt, occurs when the last tuning block fails
(the last ratio tested). The delay from CRC check until the
interrupt is asserted is bigger than the delay until assertion
of the tuning end flag. Assertion of tuning end flag is what
masks the interrupts. Because of this race, an erroneous DCRC
interrupt occurs.
The suggested workaround is to disable DCRC interrupts during
the tuning procedure which is implemented here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
HS200/SDR104 requires tuning command to be sent to the card. Use
the mmc_send_tuning library function to send the tuning
command and configure the internal DLL.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
In order to enable DDR mode, Dual Data Rate mode bit has to be set in
MMCHS_CON register. Set it here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Use the timing parameter set in the MMC core to set the
mode in UHSMS bit field. This is in preparation for
adding HS200 support in omap hsmmc driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
"ti,dual-volt" is used in linux kernel to set the voltage capabilities.
For host controller dt nodes that doesn't have "ti,dual-volt",
it's assumed 1.8v is the io voltage. This is not always true (like in
the case of beagle-x15 where the io lines are connected to 3.3v).
Hence if "no-1-8-v" property is set, io voltage will be set to 3v.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
No functional change. Move bus width configuration setting to a
separate function and invoke it only if there is a change in the
bus width.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a separate function for starting the clock, stopping the clock and
setting the clock. Starting the clock and stopping the clock can
be used irrespective of setting the clock (For example during iodelay
recalibration).
Also set the clock only if there is a change in frequency.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Use pr_* log functions from Linux. They can be enabled/disabled
via CONFIG_LOGLEVEL.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
config_fallbacks.h has some logic that sets HAVE_BLOCK_DEVICE
based on a list of enabled options. Moving HAVE_BLOCK_DEVICE to
Kconfig allows us to drastically shrink the logic in
config_fallbacks.h
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rename HAVE_BLOCK_DEVICE to CONFIG_BLOCK_DEVICE]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_APBH_DMA
CONFIG_APBH_DMA_BURST
CONFIG_APBH_DMA_BURST8
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
[trini: Add in MMC as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
Introduce SDR104 and HS200 support
The implementation takes linux kernel sdhci.c and sdhci-esdhc-imx.c
as reference.
- Implement esdhc_change_pinstate to dynamically change pad settings
- Implement esdhc_set_timing
- Implement esdhc_set_voltage to switch voltage
- Implement fsl_esdhc_execute_tuning to execute time process
- Enlarge the cfg->f_max to 200MHz.
- Parse fsl,tuning-step, fsl,tuning-start-tap and
fsl,strobe-dll-delay-target from device tree.
- Parse no-1-8-v property
- Introduce esdhc_soc_data to indicate the flags and caps
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add entries that will be used for tuning control.
The whole layout not changed, just expand reserved3[84] and
rename other reservedx in sequence.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The BCM2835 family of SoCs has 2 different SD controllers: One based on
the SDHCI spec and a custom, home-grown one.
This patch implements a driver for the latter based on the Linux driver.
This is needed so that we can make use of device trees that assume driver
presence of both SD controllers.
Signed-off-by: Alexander Graf <agraf@suse.de>
When clock is enabling, it's assigned to 0 as mmc->clock.
Then it can't initialize any card.
Fix to assign to correct clock value as mmc->cfg->f_min or f_max.
Fixes: 9546eb92cb ("mmc: fix the wrong disabling clock")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Guillaume GARDET <guillaume.gardet@free.fr>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
wait_for_bit callers use the 32 bit LE version
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Commit 4f425280fa ("mmc: fsl_esdhc: Allow all supported prescaler
values") made it possible to set SYSCTL.SDCLKFS to 0 in SDR mode on
i.MX, thus bypassing the SD clock frequency prescaler, in order to be
able to get higher SD clock frequencies in some contexts. However, that
commit missed the fact that this value is illegal on the eSDHCv3
instance of the i.MX53. This seems to be the only exception on i.MX,
this value being legal even for the eSDHCv2 instances of the i.MX53.
Fix this issue by changing the minimum prescaler value for the single
instance of the i.MX53 eSDHCv3 controller.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
When power is off, clock is not disabling.
Because it's passed to 1, mmc->clock should be set to f_min value.
Some drivers can't initialize the eMMC/SD card with current status.
This patch is to fix the disabling clock value to 0.
Fixes: 2e7410d76a ("mmc: disable the mmc clock during power off")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Guillaume GARDET <guillaume.gardet@free.fr>
Tested-by: Anand Moon <linux.amoon@gmail.com>
During the tuning, drivers repeat data transfer, changing timing
parameters in the controller hardware. So, the tuning commands
(CMD19 for SD, CMD21 for eMMC) fail, and this is not a problem
at all.
Showing "Error detected..." in normal operation just make users
upset. This should not be shown.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This line overwrites host_cap that has been set by drivers and/or
helpers like mmc_of_parse(). Accumulate capabilities flags.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
You must fix your DT if it specifies insane bus-width, for example,
bus-width = <3>;
debug() is not displayed in usual configuration, so people will not
even notice weirdness. Use dev_err() instead, then let it fail.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
mmc_of_parse() in U-Boot is a pussy helper; it sets cfg->f_max to
52MHz even if DT does not provide "max-frequency" at all. This can
overwrite cfg->f_max that may have been set to a reasonable default.
As the DT binding says, "max-frequency" is an optional property.
Do nothing if DT does not specify it. This is the behavior of
mmc_of_parse() in Linux.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
omap_hsmmc driver uses "|" in a couple of places for disabling a bit.
While it's okay to use it in "mmc_reg_out" (since mmc_reg_out has a
_mask_ argument to take care of resetting a bit), it's incorrectly used
for resetting flags in "omap_hsmmc_send_cmd".
Fix it here by using "&= ~()" to reset a bit.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Instead of sending STOP TRANSMISSION command from MMC core, enable
the auto command feature so that the Host Controller issues CMD12
automatically when last block transfer is completed.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The omap hsmmc host controller can have the ADMA2 feature. It brings better
read and write throughput.
On most SOC, the capability is read from the hl_hwinfo register. On OMAP3,
DMA support is compiled out.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This reverts commit 46831c1a4c.
This reserved area at the beginning of struct hsmm, will be used later to
support ADMA
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Current USDHC driver will reset VSELECT to 0 (3.3v) during mmc init,
then set to 1 for 1.8v eMMC I/O. When booting from eMMC, since ROM has
already set VSELECT to 1.8v before running the u-boot. This reset in
USDHC driver causes a short 2.2v pulse on CMD pin.
Fix this issue by not reset VSELECT to 0 when 1.8v flag is set.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
hc_wp_grp_size is needed only if hardware partitionning is used.
On ARM removing it saves about 30 bytes of code space.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This information is only used by the "mmc info" command.
On ARM removing this information from SPL saves about 140 of code space.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Also remove erase_grp_size and write_bl_len from struct mmc as they are
not used anymore. On ARM, removing them saves about 100 bytes of code
space in SPL.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The content of ssr is useful only for erase operations.
on ARM, removing sd_read_ssr() saves around 300 bytes.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This allows using CONFIG_IS_ENABLED(MMC_WRITE) to compile out code
needed only if write support is required.
The option is added for u-boot and for SPL
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
struct mmc_data contains the block size to use for the data transfer.
Use this information instead of using the default value or the block length
information stored in struct mmc.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The SDcard initialization procedure does a few more things than it did earlier:
* switch the bus width even for 1-bit bus width
* check that speed has been properly set (in resp[4] of SD_CMD_SWITCH_FUNC)
Update the SD simulator to handle those requests gracefully.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Not all boards have an eMMC and not all users have a need for this.
Allow to compile it out. By default it is still included.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Supporting USH and HS200 increases the code size as it brings in IO voltage
control, tuning and fatter data structures.
Use Kconfig configuration to select which of those features should be
built in.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This allows to compile out the log message by tweaking the LOGLEVEL.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Not using this function reduces the size of the binary. It's replaces by
a standard malloc() and the alignment requirement is handled by an
intermediate buffer on the stack.
Also make sure that the allocated buffer is freed in case of error.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The ext_csd is allocated only for MMC above version 4. The compare will
crash or fail for older MMCs.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Make sure that those basic capabilities are advertised by the host.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
As the legacy modes were not added to the list of supported modes, old
cards that do not support other modes could not be used.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
* convert to livetree API
* don't fail because of an invalid bus-width, instead default to 1-bit.
* recognize 1.2v DDR and 1.2v HS200 flags
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This is a useful information while debugging the initialization process or
performance issues.
Also dump this information with the other mmc info if the verbose option
is selected
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a new function to parse host controller dt node and
set mmc_config. This function can be used by mmc controller
drivers to set the generic mmc_config.
This function can be extended to set other UHS mode caps
once UHS mode support is added.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
HS200/SDR104 requires tuning command to be sent to the card.
Add a simple function to send tuning command and to read and
compare the received data with the tuning block pattern.
This function can be used by platform driver to perform DLL
tuning.
This patch is similar to
commit 996903de92f0 ("mmc: core: add core-level function for
sending tuning commands") added in linux kernel.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
HS200 only supports 1.2v and 1.8v signal voltages. DDR52 supports 3.3v/1.8v
or 1.2v signal voltages.
Select the lowest voltage available when using those modes.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
With certain SD cards like Kingston 8GB/16GB UHS card, it is seen that
MMC_CMD_ALL_SEND_CID cmd fails on first attempt, but succeeds
subsequently. Therefore, retry MMC_CMD_ALL_SEND_CID cmd a few time
as done in Linux kernel.
Similarly, it is seen that MMC_CMD_SET_BLOCKLEN may fail on first
attempt, therefore retry this cmd a few times as done in kernel.
To make it clear that those are optionnal workarounds, a new Kconfig
option 'MMC_QUIRKS' is added (enabled by default).
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Boot partitions do not support HS200. Changing to a lower performance mode
is required to access them.
mmc_select_mode_and_width() and sd_select_mode_and_width() are modified to
make it easier to call them outside of the initialization context.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If a power cycle cannot be done on Vcc, it is safer not to try the UHS
modes because we wouldn't be able to recover from an error occurring
during the UHS initialization.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add UHS modes to the list of supported modes, get the UHS capabilites of
the SDcard and implement the procedure to switch the voltage (UHS modes
use 1v8 IO lines)
During the voltage switch procedure, DAT0 is used by the card to signal
when it's ready. The optional card_busy() callback can be used to get this
information from the host driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add HS200 to the list of supported modes and introduce tuning in the MMC
startup process.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tuning is a mandatory step in the initialization of SDR104 and HS200 modes.
This callback execute the tuning process.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
There is no point in having the mmc clock enabled during
power off. Disable the mmc clock. This is similar to how it's
programmed in Linux Kernel.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
mmc clock has to be disabled in certain cases like during
the voltage switch sequence. Modify mmc_set_clock function
to take disable as an argument that signifies if the
clock has to be enabled or disabled.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
mmc/sd specification requires vdd to be disabled for 1 ms
and then enabled again during power cycle. Add a
function in mmc core to perform power cycle and set
the io signal to it's initial state.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a new callback function *send_init_stream* which start a sequence of
at least 74 clock cycles.
The mmc core uses *mmc_send_init_stream* in order to invoke the callback
function. This will be used during power cycle where the specification
requires such a sequence after power up.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a new function *mmc_set_signal_voltage* in mmc core
which can be used during mmc initialization to select the
signal voltage. Platform driver should use the set_ios
callback function to select the signal voltage.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
set_ios callback has a return value of 'int' but the mmc_set_ios()
function ignore this. Modify mmc_set_ios() and the callers of mmc_set_ios() to
to return the error status.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The MMC startup process currently handles 4 modes. To make it easier to
add support for more modes, let's make the process more generic and use a
list of the modes to try.
The major functional change is that when a mode fails we try the next one.
Not all modes are tried, only those supported by the card and the host.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The SDcard startup process currently handles only 2 modes. To make it
easier to add support for more modes, let's make the process more generic
and use a list of the modes to try.
The major functional change is that when a mode fails we try the next one.
Not all modes are tried, only those supported by the card and the host.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a simple helper function to display information (bus width and
mode) based on a capability mask. Useful for debug.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
no functionnal changes.
In order to add the support for the high speed SD and MMC modes, it is
useful to track this information.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This will be reused later in the selection of high speed and ddr modes.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The ext csd is used for comparison many times. Keep a reference content
of the ext csd in the struct mmc to avoid reading multiple times
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
no functionnal change. This is only to further reduce the size o
mmc_startup().
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
No functionnal change here. The function is really big and can be split.
The part related to bus configuration are put in 2 separate functions: one
for MMC and one for SD.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Get a reference to the regulator devices from the dts and store them
in the struct mmc for later use.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
data is defined as struct mmc_data *data.
So it should not be compared to 0.
Problem identified with Coccinelle.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Fixes emmc initialization regression on the db410c platform.
Clearing this register while SDHCI_PRESENT_STATE reports
SDHCI_CMD_INHIBIT leads to undefined behaviour on the db410c.
When commit 7dde50 was merged (mmc: sdhci: Wait for SDHCI_INT_DATA_END
when transferring), SDHCI transfers transitioned to wait for bit
SDHCI_INT_DATA_END before flagging transfers done.
Without this patch, the db410 platform fails to initialize its eMMC
due to all of its transfers timing out (SDHCI_INT_DATA_END is never
raised after all the blocks have been transferred).
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
This patch fixes some warnings when building boards that do not define
DM_I2C_COMPAT i.e. boards that entirely rely on the new i2c layer.
Signed-off-by: Felix Brack <fb@ltec.ch>
priv pointer should be freed before returning with an error value
from exynos_dwmci_get_config().
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Signed-off-by: Raghu Bharadwaj <raghu@techveda.org>
__be32_to_cpu() accepts argument of type __be32. This patch changes
type of the buffer in ALLOC_CACHE_ALIGN_BUFFER macro to __be32, which
is then passed to __be32_to_cpu().
This prevents sparse build warnings.
drivers/mmc/mmc.c: warning: cast to restricted __be32
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Signed-off-by: Karthik Tummala <karthik@techveda.org>
Add new compatible to the Uniphier SD driver for R8A77995 D3 SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add new compatible to the Uniphier SD driver for R8A77970 V3M SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The capabilities have default values which doesn't reflect the reality
when it concerns the base clock and the mul value. Use a fixe rate
for the gck. 240 MHz is an arbitrary choice, it is a multiple of the
maximum SD clock frequency handle by the controller and it allows to
get a 400 kHz clock for the card initialisation.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Convert this driver to driver model.
This driver is also used by VEXPRESS platforms which doesn't
use driver model.
Tested on STM32F746 and STM32F769 platforms.
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Update arm_pl180_mmci_init() prototype by adding struct mmc**
param. This is needed before converting this driver to driver model
in order to use arm_pl180_mmci_init() in driver model and in none
driver model implementation
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The following error has been observed on i.MX25 with a high-speed SDSC
card:
Data Write Failed in PIO Mode.
It was caused by the timeout set on PRSSTAT.BWEN, which was triggered
because this bit takes 15 ms to be set after writing the first block to
DATPORT with this card. Without this timeout, all the blocks are
properly written.
This timeout was implemented by decrementing a variable, so it was
depending on the CPU frequency. Fix this issue by setting this timeout
to a long enough absolute duration (500 ms).
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
MMC commands like MMC_CMD_ALL_SEND_CID or MMC_CMD_SEND_CSD can reach
500 us. This patch increases the polling status register delay to avoid
a timeout on a command.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Since e7881d85 "dm: mmc: Drop CONFIG_DM_MMC_OPS" DM_MMC_OPS
is no more used, remove it from STM32_SDMMC2 dependencies
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
U-Boot widely uses error() as a bit noisier variant of printf().
This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:
# define __compiletime_error(message) __attribute__((error(message)))
This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux. (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)
Let's convert error() into now treewide-available pr_err().
Done with the help of Coccinelle, excluing tools/ directory.
The semantic patch I used is as follows:
// <smpl>
@@@@
-error
+pr_err
(...)
// </smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>
The MMC framework in U-Boot does not support a systematic API for
timing switch like mmc_set_timing() in Linux.
U-Boot just provides a hook to change the clock frequency via
mmc_set_clock(). It is up to drivers if additional register
settings are needed.
This driver needs to set a correct timing mode into a register when
it migrates to a different speed mode. Only increasing clock frequency
could result in setup/hold timing violation.
The timing mode should be decided by checking MMC_TIMING_* like
drivers/mmc/host/sdhci-cadence.c in Linux, but "timing" is not
supported by U-Boot for now. Just use mmc->clock to decide the
timing mode.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add initial support for setting the vqmmc regulator. Since we do not
support 1V8 modes, set the regulator to 3V3 and enable it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Old version of the uniphier-sd 64bit IO support patchset V1 was
applied by the maintainer, update the uniphier-sd.c with the
changes from the V3 of the patchset.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch adds SD/MMC support for STM32H7 SoCs.
Here is an extraction of SDMMC main features, embedded in
STM32H7 SoCs.
The SD/MMC block include the following:
_ Full compliance with MultiMediaCard System Specification
Version 4.51. Card support for three different databus modes:
1-bit (default), 4-bit and 8-bit.
_ Full compatibility with previous versions of MultiMediaCards
(backward compatibility).
_ Full compliance with SD memory card specifications version 4.1.
(SDR104 SDMMC_CK speed limited to maximum allowed IO speed,
SPI mode and UHS-II mode not supported).
_ Full compliance with SDIO card specification version 4.0.
Card support for two different databus modes: 1-bit (default)
and 4-bit. (SDR104 SDMMC_CK speed limited to maximum allowed IO
speed, SPI mode and UHS-II mode not supported).
_ Data transfer up to 208 Mbyte/s for the 8 bit mode.
(depending maximum allowed IO speed).
_ Data and command output enable signals to control external
bidirectional drivers.
The current version of the SDMMC supports only one SD/SDIO/MMC card
at any one time and a stack of MMC Version 4.51 or previous.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the TI SOCs a PBIAS cell exists to provide a bias voltage to the MMC1
IO cells. Without this bias voltage these I/O cells can not function
properly. The PBIAS cell is controlled by software.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add OF match entries and quirks for Renesas RCar Gen3 controllers
into the driver. The IP this driver handles is in fact Matsushita
one and in used both in Socionext and Renesas chips.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Check if the OF match has any associated data and if so, use those
data as the controller quirks, otherwise fallback to the old method
of reading the controller version register to figure out the quirks.
This allows us to supply controller quirks on controllers which ie.
do not have version register.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
The Renesas RCar Gen3 contains the same controller, originally
Matsushita. This patch adds support for handling of the 64bit
FIFO on this controller.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
The Renesas RCar Gen3 contains the same controller, originally
Matsushita, yet the register addresses are shifted by 1 to the
left. The whole controller is also 64bit, including the data
FIFOs and RSP registers. This patch adds support for handling
the register IO by shifting the register offset by 1 in the IO
accessor functions.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
This patch prepares the driver to support controller(s) with registers
at locations shifted by constant. Pull out the readl()/writel() from
the driver into separate functions, where the adjustment of the register
offset can be easily contained.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Use struct udevice* as input parameter. Previous
parameters are retrieved through plat and priv data.
This to prepare to use the reset framework.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
After Simon's patch, the dtoc can work with 64bit address,
so we need to fix reg number for it.
Depend on Simon's patch set:
https://patchwork.ozlabs.org/cover/807266/
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Update the Rockchip SDHCI wrapper to support a live device tree.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Version-changes: 2
- use the dev_read_addr_ptr function in rockchip_sdhci.c
Update the Rockchip-specific wrapper for the Designware driver to
support a live device tree.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Version-changes: 2
- use the dev_read_addr_ptr function in rockchip_dw_mmc.c
Import include/linux/dma-direction.h from Linux 4.13-rc7 and delete
duplicated definitions of enum dma_data_direction.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
When enabling the new mmc timing mode, we inadvertently clear all the
remaining bits in the new timing mode register. The bits cleared
include a default phase delay on the output clock. The BSP kernel
states that the default values are supposed to be used. Clearing them
results in decreased performance or transfer errors on some boards.
Fixes: de9b1771c3 ("mmc: sunxi: Support new mode")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The driver-model rework changed, among other things, the way the private
data were moved around. It now uses the private field in the struct mmc.
However, the mmc_create argument was changed in the process to always pass
the array we used to have to store our private structures.
The basically means that all the MMC driver instances will now have the
private data of the first instance, which obviously doesn't work very well.
Pass the proper pointer to mmc_create.
Fixes: 034e226bc7 ("dm: mmc: sunxi: Pass private data around explicitly")
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Almost all of the newer Allwinner SoCs have a new operating mode for the
eMMC clocks that needs to be enabled in both the clock and the MMC
controller.
Details about that mode are sparse, and the name itself (new mode vs old
mode) doesn't give much details, but it seems that the it changes the
sampling of the MMC clock. One side effect is also that it divides the
parent clock rate by 2.
Add support for it through a Kconfig option.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This changes pci_mmc driver to use PCI_CLASS_SYSTEM_SDHCI instead of
individual vendor id & device id pair to support generic PCI SD host
controller.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This patch allows to show the EXT_CSD[179] partition_config
register info, just by specifying the dev param:
U-Boot> mmc partconf 0
EXT_CSD[179], PARTITION_CONFIG:
BOOT_ACK: 0x0
BOOT_PARTITION_ENABLE: 0x0
PARTITION_ACCESS: 0x0
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
All boards which use DM_MMC have now been converted to use DM_MMC_OPS.
Drop the option and good riddance.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable driver model for MMC (including BLK), SATA and USB. Note that USB
does not yet work correctly since the nodes are disabled. Hopefully this
can be resolved by the maintainer.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to use fsl_esdhc_init() with driver model. Move the mmc_init() out
of this function so that we can use it for our common init.
Signed-off-by: Simon Glass <sjg@chromium.org>
With driver model we want to store the mmc and configuration structure in
platform data. Set up structure up and use it for non-DM as well.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since esdhc_init_common() can fail it should return an error code. Update
this and also adjust the timeout mechanism to use get_timer(), which is a
more common approach.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since esdhc_reset() can fail it should return an error code. Update this
and also adjust the timeout mechanism to use get_timer(), which is a more
common approach.
Signed-off-by: Simon Glass <sjg@chromium.org>
Driver model wants to use the core functions in this file but accesses the
driver-private data in a different way. Move the code into new 'common'
functions and set up stubs to call these. Also sort the operations into
alphabetical order for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
With driver model we will not use mmc->priv to access driver-private data.
To accomodate this, update internal functions so that we can pass the
private data directly. This will allow the caller to obtain it as it
prefers.
Signed-off-by: Simon Glass <sjg@chromium.org>
The bind() method is called before the device is probed and so the
device has no private data, should use the platform data, and set up
a new struct to hold the mmc and cfg members.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since we now have clock driver for the RCar Gen3 , add support for
enabling the clock into the SH SDHI driver to prevent hacks in the
board files.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The command handling in this driver is awful, esp. because the driver
depends on command numbers to determine whether this is APPCMD or not.
Also, handling of command RSP response types is totally wrong.
This patch at least plucks out some of the custom command encoding and
fixes the APPCMD handling. The RSP handling still needs work, yet that
might not be needed as it turns out the uniphier-sd.c driver is in much
better shape and supports the same IP, so we might be able to just drop
this driver in favor of the uniphier one.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add MMC DM and DT probing support into the SH SDHI driver.
This patch abstracts out the common bits of the send command
and set ios functions, so they can be used both by DM and non
DM setups and adds the DM probe support.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The long response entry 0..3 LSByte comes from the next response
register MSByte, not from the next response register LSByte. Fix
this to make the driver report correct values in response 136 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We shouldn't always change the status to okay. There could be
situations that the esdhc is intentionally disabled in the device
tree.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Commit 4483b7eb added variable vqmmc_dev but only uses it under
CONFIG_DM_REGULATOR. Add the same macro to variable declaration to
get rid of compiling warning.
Signed-off-by: York Sun <york.sun@nxp.com>
Convert the pci_mmc driver over to driver model and migrate all x86 boards
that use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: remove DM_MMC from edison_defconfig]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Add a driver-model version of this driver which mostly uses the existing
code. The old code can be removed once all boards are switched over.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function has #ifdefs in it which we want to avoid for driver model.
Instead we should use different compatible strings and the .data field.
It also uses the MMC device number which is not available in driver
model except through aliases.
Move the function's into its caller so that the driver-model version can
do things its own way.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
At present the driver-private data is obtained in various functions by
various means. With driver model this is provided automatically. Without
driver model it comes from a C array declared at the top of the file.
Adjust internal functions so that they are passed the private data as
a parameter, allowing the caller to obtain it using either means.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Use the driver-model naming convention for this structure. It is data
private to the driver so the local variable should be called 'priv'.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Use the driver-model naming convention for this structure. It is data
private to the driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
At present if U-Boot proper uses driver model for MMC, then SPL has to
also. While this is desirable, it places a significant barrier to moving
to driver model in some cases. For example, with a space-constrained SPL
it may be necessary to enable CONFIG_SPL_OF_PLATDATA which involves
adjusting some drivers.
Add new SPL versions of the options for DM_MMC, DM_MMC_OPS and BLK. By
default these follow their non-SPL versions, but this can be changed by
boards which need it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update the tegra mmc driver to support a live device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Tested-by: Stephen Warren <swarren@nvidia.com>
DTB is encoded in big endian. When we retrieve property values,
we need to use fdt32_to_cpu (aka be32_to_cpu) for endian conversion.
This is a bit error-prone, but sparse is useful to detect endian
mismatch.
We need to use (fdt32_t *) instead of (u32 *) for a pointer of a
property value. Otherwise sparse warns "cast to restricted __be32".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
According to MMC spec, the write_counter is 4-byte length,
use 'int' instead of 'long' type for the 'long' is not 4-byte
in 64 bit CPU.
Signed-off-by: Jason Zhu <jason.zhu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.
This change is also coherent with the structure in kernel.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Akshay Bhat <akshaybhat@timesys.com>
CC: Ken Lin <Ken.Lin@advantech.com.tw>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Heiko Schocher <hs@denx.de>
CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
CC: Christian Gmeiner <christian.gmeiner@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Patrick Bruenn <p.bruenn@beckhoff.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: "Eric Bénard" <eric@eukrea.com>
CC: Jagan Teki <jagan@amarulasolutions.com>
CC: Ye Li <ye.li@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Adrian Alonso <adrian.alonso@nxp.com>
CC: Alison Wang <b18965@freescale.com>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Martin Donnelly <martin.donnelly@ge.com>
CC: Marcin Niestroj <m.niestroj@grinn-global.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Adam Ford <aford173@gmail.com>
CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
CC: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Soeren Moch <smoch@web.de>
CC: Richard Hu <richard.hu@technexion.com>
CC: Wig Cheng <wig.cheng@technexion.com>
CC: Vanessa Maegima <vanessa.maegima@nxp.com>
CC: Max Krummenacher <max.krummenacher@toradex.com>
CC: Stefan Agner <stefan.agner@toradex.com>
CC: Markus Niebel <Markus.Niebel@tq-group.com>
CC: Breno Lima <breno.lima@nxp.com>
CC: Francesco Montefoschi <francesco.montefoschi@udoo.org>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Scott Wood <oss@buserror.net>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Simon Glass <sjg@chromium.org>
CC: "Andrew F. Davis" <afd@ti.com>
CC: "Łukasz Majewski" <l.majewski@samsung.com>
CC: Patrice Chotard <patrice.chotard@st.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stephen Warren <swarren@nvidia.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: "Álvaro Fernández Rojas" <noltari@gmail.com>
CC: York Sun <york.sun@nxp.com>
CC: Xiaoliang Yang <xiaoliang.yang@nxp.com>
CC: Chen-Yu Tsai <wens@csie.org>
CC: George McCollister <george.mccollister@gmail.com>
CC: Sven Ebenfeld <sven.ebenfeld@gmail.com>
CC: Filip Brozovic <fbrozovic@gmail.com>
CC: Petr Kulhavy <brain@jikos.cz>
CC: Eric Nelson <eric@nelint.com>
CC: Bai Ping <ping.bai@nxp.com>
CC: Anson Huang <Anson.Huang@nxp.com>
CC: Sanchayan Maity <maitysanchayan@gmail.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Patrick Delaunay <patrick.delaunay@st.com>
CC: Gary Bisson <gary.bisson@boundarydevices.com>
CC: Alexander Graf <agraf@suse.de>
CC: u-boot@lists.denx.de
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT is not the correct method
to set I/O to 1.8. To boards that does not support vqmmc-supply,
use vs18_enable in fsl_esdhc_cfg. If regulator is supported,
use fixed 1.8V regulator for vqmmc-supply.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Handle vqmmc supply. Some boards have a fixed I/O voltage
at 1.8V for emmc, so the usdhc also needs to be configured
as 1.8V by setting VSELECT bit. The vs18_enable is the one
that used to checking whether setting VSELECT or not in
the driver. So if vqmmc supply is 1.8V, set vs18_enable,
the driver will set VSELECT.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
When using eMMC with 1.8V I/O, the VSELECT bit need to be set in
the USDHC controller when init.
This patch adds a parameter "vs18_enable" in fsl_esdhc_cfg
structure and priv data, so each controller can have different
settings.
We could not use CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT, it has problem
that it will apply to all USDHC controllers and it only set the 1.8V
at init phase. So if user does not select to the eMMC device,
the voltage on the I/O pins are not correct.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The origin patch get rockchip dwmmc by name 'ciu', which lead
to the SPL not able to remove 'clock-names' node in dts.
I'm not saying this is not correct, but I would prefer to handle
this in dts or clock driver to save memory for SPL.
For example the rk3288 SPL size has out of memory if not enable
BACK_TO_BROM option, there are many other SoCs has less internal
memory than rk3288.
This reverts commit 480a9b834c.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Since the 'clock-freq-min-max' is deprecated, we use max-frequency for
all rockchip SoC dwmmc controller.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
With the new dev_read functions available, we can convert the rockchip
architecture-specific drivers and common drivers used by these devices
over to the dev_read family of calls.
This covers the dw_mmc and sdhci wrapper drivers for Rockchip.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver is used in another board; remove board information from
the driver debug log.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This reverts commit ddb3ac3c71.
With MMC converted to driver model, SCSI driver is broken due to
zero address access at (ops->read) in block_dread() function.
The fix (SCSI driver converted to DM) is ready in u-boot-dm branch,
but it is too late for this relese to get that in.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The driver currently does not reset bit 5 of the hostctl register even if
the MMC stack requests it. Then means that once a bus width of 8 is
selected it is not possible to change it back to 1. This breaks
'mmc rescan' which needs to start off with a bus width of 1.
The problem was surfaced by enabling CONFIG_DM_MMC_OPS on tegra. Without
this option the MMC stack fully reinits the driver on a 'mmc rescan'.
But with this option driver model does not re-probe a driver once it has
been probed once.
Fix the driver to honour the request.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Peter Chubb <peter.chubb@data61.csiro.au>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We do not need to probe the block device here, so avoid doing so. The MMC
device itself must be active, but the block device can come later.
Signed-off-by: Simon Glass <sjg@chromium.org>
The Kconfig entry depends on RMOBILE, but this was renamed
to ARCH_RMOBILE in commit 1cc95f6e1b (ARM: Rmobile: Rename
CONFIG_RMOBILE to CONFIG_ARCH_RMOBILE) . Fix this omission.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
R-Car Gen3 series have four SD card interfaces (SDHI0 to SDHI3),
two of which can also be used as MMC interfaces (SDHI2 and SDHI3).
This adds High-speed mode SD clock frequency between 25MHz and 50MHz,
8bit/4bit bus width, high capacity and low voltage device support.
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add support for requesting GPIOs with a live device tree.
This involves adjusting the function signature for the legacy function
gpio_request_by_name_nodev(), so fix up all callers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes to stm32f746-disco.c:
Signed-off-by: Tom Rini <trini@konsulko.com>
The of_ prefix conflicts with the livetree version of this function.
Rename it to avoid problems when we add livetree support.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable CONFIG_DM_MMC_OPS and CONFIG_BLK for all Tegra devices. This moves
Tegra to use driver model fully for MMC.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is called when the MMC block device is being probed. There
is a recursive call in this function since find_mmc_device() itself can
cause the MMC device to be probed.
Admittedly the MMC device should already be probed, since we would not be
probing its child otherwise, but the current code is unnecessarily
convoluted.
Rewrite this to access the MMC structure directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
When binding a new MMC device, make sure that it has the required
operations. Since for now we still support *not* having the operations
(with CONFIG_DM_MMC_OPS not enabled) it makes sense to add this check.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should not call out to board code from drivers. With driver model,
mmc_power_init() already has code to use a named regulator, but the
legacy code path remains. Update the code to make this clear.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is good practice to include common.h as the first header. This ensures
that required features like the DECLARE_GLOBAL_DATA_PTR macro,
configuration options and common types are available.
Fix up some files which currently don't do this. This is necessary because
driver model will soon start using global data and configuration in the
dm/read.h header file, included via dm.h. The gd->fdt_blob value will be
used to access the device tree and CONFIG options will be used to
determine whether to support inline functions in the header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.
In the end we will have:
1. dev_read_addr...() - works on devices, supports flat/live tree
2. devfdt_get_addr...() - current functions, flat tree only
3. of_get_address() etc. - new functions, live tree only
All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.
Note this involves changing some dead code - the imx_lpi2c.c file.
Signed-off-by: Simon Glass <sjg@chromium.org>
This header includes things that are needed to make driver build. Adjust
existing users to include that always, even if other dm/ includes are
present
Signed-off-by: Simon Glass <sjg@chromium.org>
Don't build non DM_MMC code when DM_MMC defined so move
them into #ifndef CONFIG_DM_MMC
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
On i.MX, SYSCTL.SDCLKFS may be set to 0 in order to make the SD clock
frequency prescaler divide by 1 in SDR mode. In DDR mode, the prescaler
can divide by up to 512. Allow both of these settings.
The maximum SD clock frequency in High Speed mode is 50 MHz. On i.MX25,
this change makes it possible to get 48 MHz from the USB PLL
(240 MHz / 5 / 1) instead of only 40 MHz from the USB PLL
(240 MHz / 3 / 2) or 33.25 MHz from the AHB clock (133 MHz / 2 / 2).
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Number of blocks is a 9 bit field where 0 stands for a unlimited
number of blocks. Therefore the max number of blocks which can
be set is 511.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Convert the pci_mmc driver over to driver model and migrate all x86 boards
that use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
To fix the timeout of sending the write command, enable the quirk
SDHCI_QUIRK_WAIT_SEND_CMD.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This simplifies makefiles. Also, arrange the order of objects in
drivers/mmc/Makefile so that the framework objects are listed before
drivers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now CONFIG_GENERIC_MMC and CONFIG_MMC match for all defconfig.
We do not need two options for the same feature. Deprecate the
former.
This commit was generated with the sed script 's/GENERIC_MMC/MMC/'
and manual fixup of drivers/mmc/Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This driver is a counterpart of drivers/mmc/host/sdhci-cadence.c
from Linux. Some updates for v4.12-rc1 can be imported to U-Boot.
- Fix value of SDHCI_CDNS_HRS04_RDATA_SHIFT
- Add polling for ACK bit to be sure that data are written to
the PHY register
- Retrieve PHY values from DT properties instead of fixed data
The following is the list of upstream commits:
- Linux commit 4e03f628b464e0580abadf5161eaa38c61d20943
mmc: sdhci-cadence: fix bit shift of read data from PHY port
- Linux commit a0f8243229ed071c8da0ea7cedc1b7bf1b1515da
mmc: sdhci-cadence: Fix writing PHY delay
- Linux commit a89c472d8b55c5afc4c79e6e3d1338730034eb01
mmc: sdhci-cadence: Update PHY delay configuration
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In the programmable clock mode, the SDCLK frequency is incorrectly
assigned when the maximum clock has been assigned during probe,
this causes the SDHCI not work well.
In the programmable clock mode, when calculating the SDCLK Frequency
Select, when the maximum clock has been assigned, it is the actual
value, should not be multiplied by host->clk_mul. Otherwise, the
maximum clock is multiplied host->clk_mul by the base clock achieved
from the BASECLKF field of the Capabilities 0 Register.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
For platforms that don't use device tree in SPL the only
way to mark this driver as 'required by relocation' is
with the DM_FLAG_PRE_RELOC flag. Add this to ensure that
the driver is bound.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The 'clock-freq-min-max' property was deprecated in the upstream
(i.e. Linux) DTS bindings in favor of the 'max-frequency' property.
With the latest RK3399 DTSI does no longer include the deprecated
property and the rockchip_dw_mmc driver requiring it to be present,
the driver doesn't bind to the node in the RK3399 DTSI any longer
(thus breaking access to the SD card on the RK3399-Q7 board).
To fix this, we implement a similar logic as in the Linux driver: if
the deprecated property is present, we issue a warning (if DEBUG is
enabled); if it is missing, we require 'max-frequency' to be set and
use it to create a min/max value-pair.
See b023030f10
for the deprecation/matching change in Linux.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
As you know, biu_clk is used for AMBA AHB/APB interface, ciu_clk is
used for communication between host and card devices. The real bus clock
is ciu, so let's rectify it.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch changes the way DM_MMC calculates offset to the base register of
MMC. Previously this was through an #ifdef but that wasn't necessary for OMAP3.
This patch will now add in the offset to the base address based on the
.compatible flags.
Signed-off-by: Adam Ford <aford173@gmail.com>
V2: Remove ifdef completely and reference offset from the omap_hsmmc_ids table.
V1: Change ifdef to ignore OMAP3
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert the bcm2835 SDHCI driver over to support CONFIG_DM_MMC and move
all boards over. There is no need to keep the old code since there are no
other users.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
These drivers have no user since commit ea3310e8aa ("Blackfin:
Remove").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
sdhci_transfer_data() function transfers the blocks passed up to the
number of blocks defined in mmc_data, but returns immediately once all
the blocks are transferred, even if the loop exit condition is not met
(bit SDHCI_INT_DATA_END set in the STATUS word).
When doing multiple writes to mmc, returning right after the last block
is transferred can cause the write to fail when sending the
MMC_CMD_STOP_TRANSMISSION command right after the
MMC_CMD_WRITE_MULTIPLE_BLOCK command, leaving the mmc driver in an
unconsistent state until reboot. This error was observed in the rpi3
board.
This patch waits for the SDHCI_INT_DATA_END bit to be set even after
sending all the blocks.
Test: Reliably wrote 2GiB of data to mmc in a rpi3.
Signed-off-by: Alex Deymo <deymo@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The linux kernel driver for this module does not use a delay when
writing to the SDHCI_BUFFER register. This patch mimics that behavior
in order to speed up the mmc writes on the Raspberry Pi.
Signed-off-by: Alex Deymo <deymo@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the driver model support for Atmel mci while retaining the
existing legacy code. This allows the driver to support boards
that have converted to driver model as well as those that have not.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver implements MMC support on Meson GX (S905) based systems.
It's based on Carlo Caione's work, changes:
- BLK support added
- general refactoring
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
This patch adds the flags parameter to device_remove() and changes all
calls to this function to provide the default value of DM_REMOVE_NORMAL
for "normal" device removal.
This is in preparation for the driver specific pre-OS (e.g. DMA
cancelling) remove support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Introduce CONFIG_TEGRA124_MMC_DISABLE_EXT_LOOPBACK to disable the external clock
loopback and use the internal one on SDMMC3 as per the SDMMC_VENDOR_MISC_CNTRL_0
register's SDMMC_SPARE1 bits being set to 0xfffd according to the TRM.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This is a preparation work for the support of CONFIG_BLK.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
For consistency, use an accessor to access the private data. Also for the
same reason, rename all priv_data to priv.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The Xenon SDHCI driver just missed the integration of this patch:
git ID 6d0e34bf
mmc: sdhci: Distinguish between base clock and maximum peripheral frequency
With this patch applied, the SDHCI subsystem complains now with this warning
while probing:
sdhci_setup_cfg: Hardware doesn't specify base clock frequency
This patch fixes this issue, by providing the missing host->max_clk
variable to the SDHCI subsystem.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Hu Ziji <huziji@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
It's redundant to send cmd13 after cmd9 whose response is not R1b. The
card devices will not be busy w/ cmd9.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
This patch adds Intel Tangier eMMC/SDHCI driver.
Intel Tangier SoC contains a hybrid of PCI and non-PCI devices. SDHCI
controller is one of the devices which are *not* on a PCI and, hence,
cannot be enumerated by standard PCI means. This driver, allows for
SDHCI controller on Tangier SoC to work in U-Boot.
Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We don't want pci_mmc to compile every time x86 compiles, only when
there's a platform that needs it. For that reason, we're adding a new
CONFIG_MMC_PCI which platforms can choose to enable.
Suggested-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This includes support for rk3188 from Heiko Stübner and and rk3328 from
Kever Yang. Also included is SPL support for rk3399 and a fix for
rk3288 to get it booting again (spl_early_init()).
Add compatible property for i.MX7ULP.
Add a weak init_usdhc_clk function, i.MX7ULP use this to init the clock.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Change some API in order to enable of-platdata.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added rockchip tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
- Move to DM clk driver
- Add clk support for zynq_sdhci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAljKWVcACgkQykllyylKDCEsgACfey0mgRaGVMLSxMMCGgJQIK70
/oYAn3raqYrJ2e2fsjb1B5WodYcDe8L5
=JYC5
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2017.05' of git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2017.05
- Move to DM clk driver
- Add clk support for zynq_sdhci
This device tree has been extracted from v4.9 kernel
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add SDHCI host controller found on STMicroelectronics SoCs
On some ST SoCs, i.e. STiH407/STiH410, the MMC devices can live
inside a dedicated flashSS sub-system that provides an extend subset
of registers that can be used to configure the Arasan MMC/SD Host
Controller.
This means, that the SDHCI Arasan Controller can be configured to be
eMMC4.5 or 4.3 spec compliant.
W/o these settings the SDHCI will configure and use the MMC/SD
controller with limited features e.g. PIO mode, no DMA, no HS etc.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The maximum supported peripheral clock frequency of the zynq depends on
the IO routing. The MIO and EMIO support a maximum frequency of 50 MHz
respectively 25 MHz. Use the max-frequency value of the device tree to
determine the maximal supported peripheral clock frequency.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The zynq_sdhci controller driver use CONFIG_ZYNQ_SDHCI_MAX_FREQ as base
clock frequency but this clock is not fixed and depends on the hardware
configuration. Additionally the value of CONFIG_ZYNQ_SDHCI_MAX_FREQ
doesn't match the real base clock frequency of SDIO_FREQ. Use the clock
framework to determine the frequency at run time.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
It was incorrect to always include "asm/arch-omap3/mux.h" constantly.
This introduced warnings on non-omap3 where certain values will conflict
between the various families. Conditionally guard the inclusion in
order to correct the problem.
Fixes: 6aca17c9b7 ("drivers: mmc: omap_hsmmc: Fix IO Buffer on OMAP36xx")
Signed-off-by: Tom Rini <trini@konsulko.com>
MMC devices accessed exclusively via the driver model were not
being initialized before being exposed as block devices, causing
issues in scenarios where the MMC device is first accessed via the
uclass block interface.
Signed-off-by: Fiach Antaw <fiach.antaw@uqconnect.edu.au>
On the OMAP36xx/37xx the CONTROL_WKUP_CTRL register has
a field (bit 6) named GPIO_IO_PWRDNZ. If 0, the IO buffers which
are related to GPIO_126, 127 and 129 are disabled. Some boards may
need this for MMC. After the PBIAS is configured, this bit should
be set high to enable these GPIO pins.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
ftsdc021_sdhci.c is dead file.
There is no reason to maintain this host controller.
Removes the entire ftsdc021_sdhci.c.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
If there are alias nodes as "mmc", use the devnum as alias index
number.
This patch is for fixing a problem of Exynos4 series.
Problem is the below thing.
Current legacy mode:
EXYNOS DWMMC: 0, SAMSUNG SDHCI: 1
After using DM:
SAMSUNG SDHCI: 0, EXYNOS DWMMC: 1
Dev index is swapped.
Then u-boot can't find the kernel image..because it is already set to 0 as mmcdev.
If change from legacy to DM, also needs to touch all exynos4 config file.
For using simply, just supporting the fixed devnum with alias node is better than it.
Usage:
alaise {
....
mmc0 = &sdhci2; /* eMMC */
mmc1 = &sdhci1; /* SD */
...
}
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
While we are here, add "depends on ARCH_AT91".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
While we are here, add "depends on ARCH_ROCKCHIP".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Make the naming scheme consistent; all SDHCI-base drivers prefixed
with CONFIG_MMC_SDHCI_.
While we are here, add "depends on ARCH_ZYNQ || ARCH_ZYNQMP".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[1] Rename CONFIG_SANDBOX_MMC to CONFIG_MMC_SANDBOX for consistency
I want all MMC driver options prefixed with CONFIG_MMC_.
[2] Fix dependency
Add necessary depends on to avoid compile error.
Instead "depends on MMC" is unneeded because this config entry
resides inside of "if MMC".
[3] Currently, this config symbol is not referenced at all.
Use it to enable/disable the driver in Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now, CONFIG_GENERIC_MMC seems equivalent to CONFIG_MMC.
Let's create an entry for "config GENERIC_MMC" with "default MMC",
then convert all macro defines in headers to Kconfig. Almost all
of the defines will go away.
I see only two exceptions:
configs/blanche_defconfig
configs/sandbox_noblk_defconfig
They define CONFIG_GENERIC_MMC, but not CONFIG_MMC. Something
might be wrong with these two boards, so should be checked later.
Anyway, this is the output of the moveconfig tool.
This commit was created as follows:
[1] create a config entry in drivers/mmc/Kconfig
[2] tools/moveconfig.py -r HEAD GENERIC_MMC
[3] manual clean-up of garbage comments in doc/README.* and
include/configs/*.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This driver implementes platform specific code for the Xenon SDHCI
controller which is integrated in the Marvell MVEBU Armada 37xx and
Armada 7k / 8K SoCs.
History:
This driver is ported from the Marvell U-Boot version 2015.01 which is
written by Victor Gu <xigu@marvell.com> with minor changes ported from
the Linux driver which is written by Ziji Hu <huziji@marvell.com>.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Some SDHCI drivers might need to do some special controller configuration
after the common clock set_ios() function has been called (speed / width
configuration). This patch adds a call to the newly created function
set_ios_port() when its configured in the host driver.
This will be used by the Xenon SDHCI controller driver used on the
Marvell Armada 3700 and 7k/8k ARM64 SoCs.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This patch completely clears the SDHCI_CLOCK_CONTROL register before the
new value is configured instead of just clearing the 2 bits
SDHCI_CLOCK_CARD_EN and SDHCI_CLOCK_INT_EN. Without this change, some
clock configurations will lead to the "Internal clock never stabilised."
error message on the Xenon SDHCI controller used on the Marvell Armada
3700 and 7k/8k ARM64 SoCs.
The Linux SDHCI core driver also writes 0 to this register before
the new value is configured. So this patch simplifies the driver a bit
and brings the U-Boot driver more in-line with the Linux one.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Print the error code for non-zero (failure case) instead
of making debug statement without any condition, this
usually gives proper clue in failure condition.
Log:
The sdhci controller assumes that the base clock frequency is fully supported by
the peripheral and doesn't support hardware limitations. The Linux kernel
distinguishes between base clock (max_clk) of the host controller and maximum
frequency (f_max) of the card interface. Use the same differentiation and allow
the platform to constrain the peripheral interface.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Move fdt fixup of 'status' property into a weak function. This allows
board to define 'status' fdt fixup by themselves.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch is to add 'fsl,esdhc' into of_match table to support
driver model for QorIQ eSDHC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
There would be compiling error as below when enable driver model for esdhc.
undefined reference to `dm_gpio_get_value'
undefined reference to `gpio_request_by_name_nodev'
This patch is to make GPIO support optional with CONFIG_DM_GPIO. Because
all boards of QorIQ platform don't need it and they just check register for
CD/WP status, only some boards of i.MX platform require this.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Commit f401e907fc ("ARM: sunxi: remove bare default for
CONFIG_MMC") dropped "depends on UART0_PORT_F", but it is still
needed. Revive it as a prerequisite of CONFIG_MMC_SUNXI.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Until recently, sdhci_ops was used only for overriding IO accessors.
(so, host->ops was not set by any drivers except bcm2835_sdhci.c)
Now, we have more optional callbacks, get_cd, set_control_reg, and
set_clock. However, the code
if (host->ops->get_cd)
host->ops->get_cd(host);
... expects host->ops is set for all drivers.
Commit 5e96217f04 ("mmc: pic32_sdhci: move the code to
pic32_sdhci.c") and commit 62226b6863 ("mmc: sdhci: move the
callback function into sdhci_ops") added sdhci_ops for pic32_sdhci.c
and s5p_sdhci.c, but the other drivers still do not (need not) set
host->ops because all callbacks in sdhci_ops are optional.
host->ops must be checked to avoid the system crash caused by NULL
pointer access.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Init the clock rate to max-frequency from dts with clock driver api.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Move (and rename) the following CONFIG options to Kconfig:
CONFIG_DAVINCI_MMC (renamed to CONFIG_MMC_DAVINCI)
CONFIG_OMAP_HSMMC (renamed to CONFIG_MMC_OMAP_HS)
CONFIG_MXC_MMC (renamed to CONFIG_MMC_MXC)
CONFIG_MXS_MMC (renamed to CONFIG_MMC_MXS)
CONFIG_TEGRA_MMC (renamed to CONFIG_MMC_SDHCI_TEGRA)
CONFIG_SUNXI_MMC (renamed to CONFIG_MMC_SUNXI)
They are the same option names as used in Linux.
This commit was created as follows:
[1] Rename the options with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_DAVINCI_MMC/CONFIG_MMC_DAVINCI/g
s/CONFIG_OMAP_HSMMC/CONFIG_MMC_OMAP_HS/g
s/CONFIG_MXC_MMC/CONFIG_MMC_MXC/g
s/CONFIG_MXS_MMC/CONFIG_MMC_MXS/g
s/CONFIG_TEGRA_MMC/CONFIG_MMC_SDHCI_TEGRA/g
s/CONFIG_SUNXI_MMC/CONFIG_MMC_SUNXI/g
'
[2] Commit the changes
[3] Create entries in driver/mmc/Kconfig.
(copied from Linux)
[4] Move the options with the following command
tools/moveconfig.py -y -r HEAD \
MMC_DAVINCI MMC_OMAP_HS MMC_MXC MMC_MXS MMC_SDHCI_TEGRA MMC_SUNXI
[5] Sort and align drivers/mmc/Makefile for readability
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Move (and rename) the following CONFIG options to Kconfig:
CONFIG_EXYNOS_DWMMC (renamed to CONFIG_MMC_DW_EXYNOS)
CONFIG_HIKEY_DWMMC (renamed to CONFIG_MMC_DW_K3)
CONFIG_SOCFPGA_DWMMC (renamed to CONFIG_MMC_DW_SOCFPGA)
The "HIKEY" is a board name, so it is not suitable for the MMC
controller name. I am following the name used in Linux.
This commit was generated as follows:
[1] Rename the config options with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_EXYNOS_DWMMC/CONFIG_MMC_DW_EXYNOS/g
s/CONFIG_HIKEY_DWMMC/CONFIG_MMC_DW_K3/g
s/CONFIG_SOCFPGA_DWMMC/CONFIG_MMC_DW_SOCFPGA/g
'
[2] Commit the changes
[3] Create the entries in drivers/mmc/Kconfig
(with default y for EXYNOS and SOCFPGA)
[4] Run the following:
tools/moveconfig.py -y -r HEAD MMC_DW_EXYNOS MMC_DW_K3 MMC_DW_SOCFPGA
[5] Sort and align drivers/mmc/Makefile for readability
[6] Clean-up doc/README.socfpga by hand
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This commit was created as follows:
[1] Rename the option with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e 's/CONFIG_DWMMC/CONFIG_MMC_DW/g'
[2] create the entry for MMC_DW in drivers/mmc/Kconfig
(the prompt and help were copied from Linux)
[3] run "tools/moveconfig.py -y MMC_DW"
[4] add "depends on MMC_DW" to the MMC_DW_ROCKCHIP entry
[5] Clean-up doc/README.socfpga by hand
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
I am trying to make all DesignWare-based driver options prefixed
with CONFIG_MMC_DW_.
This commit was generated as follows:
find . -name .git -prune -o -type f -print | \
xargs sed -i -e 's/ROCKCHIP_DWMMC/MMC_DW_ROCKCHIP/g'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Some MMC drivers describe operations with the DM_MMC_OPS form, but
there are still several drivers with older implementation. We can
not compile drivers from different groups at the same time because
the core framework is shared with #ifdef CONFIG_DM_MMC_OPS.
Every driver should have "depends on DM_MMC_OPS" (or !DM_MMC_OPS)
explicitly to express which framework it is based on. This will
avoid enabling drivers with incompatible interface at the same time.
It is incorrect to make a driver "select DM_MMC_OPS".
While we are here, add "depends on OF_CONTROL" as well because this
driver can be configured only by Device Tree.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
callback function should be moved into sdhci_ops struct.
Other controller can use these ops for controlling clock or their own
specific register.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Add the s5p_set_clock function.
It's not good that "set_mmc_clk" is assigned directly.
In future, it should be changed to use the clock framework.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
This code is used for only pic32_sdhci controller.
To remove the "#ifdef", moves to pic32_sdhci.c.
And use the get_cd callback function.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Buswidth is depeneded on Hardware schematic.
Evne though host can support the 8bit buswidth, if hardware doesn't
support 8bit mode, it doesn't work fine.
So the buswidth mode selection leaves a matter in each SoC drivers.
On the contrary to this, hardware supports 8bit mode, but host doesn't
support it. then controller has to disable the MMC_MODE_8BIT.
(Host can check whether 8bit mode is supported or not, since V3.0)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Add option SYS_FSL_ERRATUM_ESDHC111, SYS_FSL_ERRATUM_ESDHC13,
SYS_FSL_ERRATUM_ESDHC135, SYS_FSL_ERRATUM_ESDHC_A001 to mmc Kconfig.
Move existing macros to related Kconfig.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate bk4r1]
Signed-off-by: Tom Rini <trini@konsulko.com>
This is a user-unconfigurable option that is selected by the
drivers that need to overwrite SDHCI IO memory accessors.
(BCM2835 SDHCI seems the only driver that needs to do so.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
While I moved the options, I also renamed them so that they are all
prefixed with MMC_SDHCI_.
This commit was created in the following steps.
[1] Rename with the following command
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_MMC_SDMA/CONFIG_MMC_SDHCI_SDMA/g
s/CONFIG_BCM2835_SDHCI/CONFIG_MMC_SDHCI_BCM2835/g
s/CONFIG_KONA_SDHCI/CONFIG_MMC_SDHCI_KONA/g
s/CONFIG_MV_SDHCI/CONFIG_MMC_SDHCI_MV/g
s/CONFIG_S5P_SDHCI/CONFIG_MMC_SDHCI_S5P/g
s/CONFIG_SPEAR_SDHCI/CONFIG_MMC_SDHCI_SPEAR/g
'
[2] create the Kconfig entries in drivers/mmc/Kconfig
[3] Move the options by the following command
tools/moveconfig.py -y MMC_SDHCI_SDMA MMC_SDHCI_BCM2835 \
MMC_SDHCI_KONA MMC_SDHCI_MV MMC_SDHCI_S5P MMC_SDHCI_SPEAR
[4] Sort drivers/mmc/Makefile for readability
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Move CONFIG_SDHCI to Kconfig and rename it to CONFIG_MMC_SDHCI.
My motivation for the rename is, ultimately, to make all the MMC
options prefixed with MMC_ and SDHCI options with MMC_SDHCI_,
like Linux.
This commit was created as follows:
[1] Rename the config option with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e 's/CONFIG_SDHCI/CONFIG_MMC_SDHCI/g'
[2] create the entry for MMC_SDHCI in drivers/mmc/Kconfig
[3] run "tools/moveconfig.py -y MMC_SDHCI"
[4] add "depends on MMC_SDHCI" to existing SDHCI driver entries
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Currently, CONFIG_MMC is not related to any other options by
"depends on" or "select". One of big advantages of using Kconfig
is automatic dependency tracking, but the current state is lacking
it. As the first step, make the existing MMC driver entries depend
on MMC.
This commit was created by the following steps:
[1] Run the following script:
--------------------8<--------------------
rm -f tmp.txt
for d in $(find . -path './configs/*_defconfig')
do
if grep -q -e 'CONFIG_MSM_SDHCI=y' $d ||
grep -q -e 'CONFIG_ATMEL_SDHCI=y' $d ||
grep -q -e 'CONFIG_ROCKCHIP_DWMMC=y' $d ||
grep -q -e 'CONFIG_SH_SDHI=y' $d ||
grep -q -e 'CONFIG_PIC32_SDHCI=y' $d ||
grep -q -e 'CONFIG_ZYNQ_SDHCI=y' $d ||
grep -q -e 'CONFIG_ROCKCHIP_SDHCI=y' $d ||
grep -q -e 'CONFIG_MMC_UNIPHIER=y' $d ||
grep -q -e 'CONFIG_SANDBOX_MMC=y' $d
then
echo CONFIG_MMC=y >> $d
echo ${d#./configs/} >> tmp.txt
fi
done
tools/moveconfig.py -y -s -d tmp.txt
rm tmp.txt
--------------------8<--------------------
[2] surround MMC driver entries with "if MMC" and "endif"
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Commit 7a777f6d6f ("mmc: Add generic Kconfig option") created
a Kconfig entry for this option without any actual moves, then
commit 44c798799f ("sunxi: Use Kconfig CONFIG_MMC") moved
instances only for SUNXI.
We generally do not like such partial moves. This kind of work
is automated by tools/moveconfig.py, so it is pretty easy to
complete this move.
I am adding "default ARM || PPC || SANDBOX" (suggested by Tom).
This shortens the configs and will ease new board porting.
This commit was created as follows:
[1] Edit Kconfig (remove the "depends on", add the "default",
copy the prompt and help message from Linux)
[2] Run 'tools/moveconfig.py -y -s -r HEAD MMC'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Remove the entire spear_sdhci.c file.
There is no use case. This is dead codes.
Also there is no place to call "spear_sdhci_init()" anywhere.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Palmas driver assumes it is always TPS659xx regulator on all DRA7xx based
boards to enable mmc regulator. This is not true always like in case of
DRA71x-evm. So get this information based on the board.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Delete omap4_vmmc_pbias_config from omap_hsmmc.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
CONFIG_AM57XX is just an unnecessary macro that is redundant given So,
remove the same instead of spreading through out the u-boot source
code and getting in the way to maintain common code for DRA7x family.
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add new configuration option CONFIG_MMC_TINY which strips away all
memory allocation within the MMC code and code for handling multiple
cards. This allows extremely space-constrained SPL code use the MMC
framework.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
If debug() is not used, then the whole content of debug(...) will
be removed by the preprocessor, which will result in the following
warning. This patch adds __maybe_unused annotation to fix this.
drivers/mmc/mmc.c: In function ‘mmc_init’:
drivers/mmc/mmc.c:1685:11: warning: variable ‘start’ set but not used [-Wunused-but-set-variable]
unsigned start;
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Add new command that provides possibility to enable the
background operations handshake functionality
(BKOPS_EN, EXT_CSD byte [163]) on eMMC devices.
This is an optional feature of eMMCs, the setting is write-once.
The command must be explicitly taken into use with
CONFIG_CMD_BKOPS_ENABLE.
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
At sdhci_get_config(), there was wrong condition to check pimux
id, so this patch fixes to check proper pinmux id.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
The sun8i SoCs also have a 8 bits capable MMC2 controller. Enable the
support for those too.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Some eMMC will fail at the first switch, but would succeed in a subsequent
one.
Make sure we try several times to cover those cases. The number of retries
(and the behaviour) is currently what is being used in Linux.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Due to the peripheral and generated clock driver improvement,
remove the unnecessary clock calling.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
If vmmc didn't supply, we didn't know which card didn't supply vmmc.
And changed from "put" to "debug".
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Now that CONFIG_BLK and CONFIG_MMC_OPS are enabled by default with
CONFIG_DM_MMC, the DWMMC driver on the socfpga platform fails at
runtime.
This adds the missing fields in the driver declaration.
Signed-off-by: Sylvain Lesne <lesne@alse-fr.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This pathc is fixed the below thing.
If misaligned the cache range, Just flush to CACHLINE_SIZE.
"CACHE: Misaligned operation at range [7ae55b00, 7ae55b08]"
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
In device tree, there is vmmc-supply property for SD/MMC.
Introduce mmc_power_init function to handle vmmc-supply.
mmc_power_init will first invoke board_mmc_power_init to
avoid break boards which already implement board_mmc_power_init.
If DM_MMC and DM_REGULATOR is defined, the regulator
will be enabled to power up the device.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
These two options go together and it is best to do the conversion in one
step. So enable DM_MMC_OPS by default if DM_MMC is enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the generic error number instead of meaningless value.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
"host->version" isn't a SoC specific value.
It doesn't need to get in each SoC drivers.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Some arguments don't need to pass to dwmci_setup_cfg.
They are already included in dwmci_host structure.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch support the driver model for s5p_sdhci controller.
To support the legacy model, maintained the existing code.
Note: If use the Driver Model, it needs to modify the device-tree.
In future, will update the Device-tree and enable the configuratioin.
(CONFIG_BLK, CONFIG_DM_MMC and CONFING_DM_MMC_OPS)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
By default saveenv option is not supported for SPL. This patch
enable the support for save environment variable for SPL build.
Enable save environment support in SPL after setenv. By default
the saveenv option is not provided in SPL, but some boards need
this support in 'Falcon' boot, where SPL need to boot from
different images based on environment variable set by OS. For
example OS may set "reboot_image" environment variable to
"recovery" inorder to boot recovery image by SPL. The SPL read
"reboot_image" and act accordingly and change the reboot_image
to default mode using setenv and save the environemnt.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Simon Glass <sig@chromium.org>
change in v1:
- dropped SUPPORT, use CONFIG_SPL_SAVEENV
- updates the comments in mmc_private.h
Need to initialize mmc->dev when probe, or will met
"dev_get_uclass_priv: null device", when `mmc dev 1`.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that the standard clock/reset APIs are available for all Tegra SoCs,
convert the MMC driver to use them exclusively, and remove any references
to the custom Tegra-specific APIs.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Convert the Tegra MMC driver to DM_MMC. Support for non-DM is removed
to avoid ifdefs in the code. DM_MMC is now enabled for all Tegra builds.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
(swarren, fixed some NULL pointer dereferences, removed extraneous
changes, rebased on various other changes, removed non-DM support etc.)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
struct mmc_host is a Tegra-specific structure, but the name implies it's
something defined by core MMC code, which is confusing. Rename it to
struct tegra_mmc_priv to make its purpose more obvious. The new name is
also more appropriate for a DM driver private data structure, which will
be relevant later in this series.
Nothing needs access to this type except the MMC driver itself. Move the
definition into the driver C file.
Make sure all Tegra MMC functions are named tegra_mmc_*. Even though
they're all static, it's useful to have good naming so that symbol tables
are easy to interpret. A few functions aren't renamed by this patch since
they'll be deleted by a subsequent patch in this series.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The MMC driver will soon be converted to use standard clock/reset APIs,
and so the periph_id field in the MMC device priv struct will disappear.
Rework the implementation of pad_init_mmc() to rely on this; using the
device register address is a much more direct test anyway.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
pad_init_mmc() is performing an SoC-specific operation, using registers
within the MMC controller. There's no reason to implement this code
outside the MMC driver, so move it inside the driver.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Tegra MMC driver currently honors "sdhci" entries in /aliases. The
MMC core however uses "mmc" entries in /aliases. This difference will be
relevant once the Tegra MMC driver is converted to DM, and the MMC core
handles alias lookups. To avoid issues during that conversion, fix the
Tegra MMC driver and all Tegra DTs to use the same alias name as the MMC
core does.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Now, include/linux/errno.h is a wrapper of <asm-generic/errno.h>.
Replace all include directives for <asm-generic/errno.h> with
<linux/errno.h>.
<asm-generic/...> is supposed to be included from <asm/...> when
arch-headers fall back into generic implementation. Generally, they
should not be directly included from .c files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Add drivers/usb/host/xhci-rockchip.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
These functions can be much simpler by squashing lines for immediate
return.
For *_bind() callbacks, they will be a simple wrapper function of an
upper-level bind API.
For mmc_set_{boot_bus_width,part_conf}, they will be a wrapper of
mmc_switch().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
When DTO interrupt occurred, there are any remaining data still in FIFO
due to RX FIFO threshold is larger than remaining data. It also
causes that dwmmc didn't trigger RXDR interrupt, so is TX.
It's responsibility of driver to read remaining bytes on seeing DTO
interrupt.
Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
To SD, there is no erase group, then the value erase_grp_size
will be default 1. When erasing SD blocks, the blocks will be
erased one by one, which is time consuming.
We use AU_SIZE as a group to speed up the erasing.
Erasing 4MB with a SD2.0 Card with AU_SIZE 4MB.
`time mmc erase 0x100000 0x2000`
time: 44.856 seconds (before optimization)
time: 0.335 seconds (after optimization)
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Clemens Gruber <clemens.gruber@pqgruber.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Eric Nelson <eric@nelint.com>
Cc: Stephen Warren <swarren@nvidia.com>
Add function to read SD_STATUS information.
According to the information, get erase_timeout/erase_size/erase_offset.
Add a structure sd_ssr to include the erase related information.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Clemens Gruber <clemens.gruber@pqgruber.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Eric Nelson <eric@nelint.com>
Cc: Stephen Warren <swarren@nvidia.com>
No need for per-SoC adjustment for this parameter. It should be
determined by the slowest hardware. Currently, no board overrides
this CONFIG, so 3.2 sec is large enough. (If not, we can make it
even larger.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This CONFIG is not configurable since it is not guarded by #ifndef.
Nobody has complained about that, so there is no need to keep it as
a CONFIG option.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If CONFIG_BLK is enabled, add_sdhci() is never called. Move this
quirk handling to sdhci_setup_cfg(), which is now the central place
for hardware capability checks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If CONFIG_BLK is enabled, add_sdhci() is never called. Move this
quirk handling to sdhci_setup_cfg(), which is now the central place
for hardware capability checks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
"Hardware doesn't specify base clock frequency" may not be only the
error case of sdhci_setup_cfg(). It is better to print this where
the corresponding error is triggered.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If CONFIG_BLK is enabled, add_sdhci() is never called.
So, sdhci_reset() is not called, either. This is a problem for
my board as it needs the reset to start from a sane state.
Move the add_sdhci() call to sdhci_init(), which is visited
by both of the with/without CONFIG_BLK cases.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This is the state-of-the-art MMC driver implementation.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With the CONFIG_DM_MMC_OPS migration, the .set_ios callback can
return an integer now. Return an appropriate error value rather
than sudden death by BUG().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
No more reason to define this function above the ops structure.
Move it near the caller. Also, change its return type to void
because it never fails.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Catch up with the DM migration.
As struct dm_mmc_ops does not have .init callback, call the init
function directly from the probe function.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Tegra SDHCI binding dictates that the reseet name for the Tegra SDHCI
clock be "sdhci" not "sdmmc", and that the clock is accessed by index
rather than by name. Fix the Tegra186 DT and MMC driver to honor this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
