By making dram_init_banksize() return an error code we can drop the
wrapper. Adjust this and clean up all implementations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
At present we cannot use this function as an init sequence call without a
wrapper, since it returns the RAM size. Adjust it to set the RAM size in
global_data instead, and return 0 on success.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
It looks like only cm5200 and tqm8xx use this feature, so we don't really
need it in generic code. Drop it and have the users access gd->board_type
directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
USB requires 100MHz clock. On LS1012A, a dedicated 100MHz is provided
instead of SYSCLK (125MHz). Skipping checking SYSCLK for FDT fixup.
Signed-off-by: Yingxi Yu <yingxi.yu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The LS2088A series SoCs has different physical memory map address and
CCSR registers address against LS2080A series SoCs.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This i2c errata only applies to LS2080A and its variants, namely
LS2080A, LS2085A and LS2088A.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
SerDes information is not necessary to be present in RCWSR29 register.
It may vary from SoC to SoC.
So Avoid RCWSR28 register hard-coding.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
MAC number used per QSGMII is not fixed. It may wary from SoC to SoC.
So move QSGMII wriop_init_dpmac() to SoC file.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Erratum A009635 is valid only for LS2080A SoC and its
personality. Add SoC svr check.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Read DMA operations causes CRC error on armv8 chassis 2 platforms
due to the erratum A-010635.
In order to support sata on these platforms, ECC needs to be disabled.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In early MMU table, DDR has to be mapped as device memory to avoid
speculative access. After DDR is initialized, it needs to be updated
to normal memory to allow code execution. To simplify the code,
dram_init() is moved into a common file as a weak function.
Signed-off-by: York Sun <york.sun@nxp.com>
Early MMU improves performance especially on emulators. However, the
early MMU is left enabled after the first stage of SPL boot. Instead
of flushing D-cache and dealing with re-enabling MMU for the second
stage U-Boot, disabling it for SPL build simplifies the process. The
performance penalty is unnoticeable on the real hardware. As of now,
SPL boot is not supported by existing emulators. So this should have
no impact on emulators.
Signed-off-by: York Sun <york.sun@nxp.com>
This patch follows the break-before-make process when making changes
to MMU table. MMU is disabled before changing TTBR to avoid any
potential race condition.
Signed-off-by: York Sun <york.sun@nxp.com>
Update mapping with actual DDR size. Non-existing memory should not
be mapped as "normal" memory to avoid speculative access.
Signed-off-by: York Sun <york.sun@nxp.com>
For ARMv8 Layerscape SoCs, secure memory and MC memorey are reserved
at the end of DDR. DDR is spit into two or three banks. This patch
reverts commit aabd7ddb and simplifies the calculation of reserved
memory, and moves the code into common SoC file. Secure memory is
carved out first. DDR bank size is reduced. Reserved memory is then
allocated on the top of available memory. U-Boot still has access
to reserved memory as data transferring is needed. Device tree is
fixed with reduced memory size to hide the reserved memory from OS.
The same region is reserved for efi_loader.
Signed-off-by: York Sun <york.sun@nxp.com>
This moves all of the current ARM errata from various header files and in to
Kconfig. This allows for a minor amount of cleanup as we had some instances
where both a general common header file was enabling errata as well as the
board config. We now just select these once at the higher level in Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
IFC IP clock is always a constant divisor of platform clock
pre-defined per SoC. Clock control register (CCR) used in
current implementation governs IFC IP output clock.
Update sys_info->freq_localbus to represent IFC input clock with
value constant divisor of platform clock.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Moved the config FSL_PPA_ARMV8_PSCI from fsl-layerscape's Kconfig to
Kconfig under armv8 and renamed it to SEC_FIRMWARE_ARMV8_PSCI.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For 64-bit kernel, there is a warning about x1-x3 nonzero in violation
of boot protocol. To fix this issue, input argument 4 is added for
armv8_switch_to_el2 and armv8_switch_to_el1. The input argument 4 will
be set to the right value, such as zero.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The default MSI node in kernel tree is for LS1043A rev1.0 silicon, if
rev1.1 silicon used, need to fixup the MSI node to match it.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The LS1043A rev1.1 silicon supports two types of GIC offset: 4K
alignment and 64K alignment. The bit SCFG_GIC400_ALIGN[GIC_ADDR_BIT]
is used to choose which offset will be used.
The LS1043A rev1.0 silicon only supports the CIG offset with 4K
alignment.
If GIC_ADDR_BIT bit is set, 4K alignment is used, or else 64K alignment
is used. 64K alignment is the default setting.
Overriding the weak smp_kick_all_cpus, the new impletment is able to
detect GIC offset.
The default GIC offset in kernel device tree is using 4K alignment, it
need to be fixed if 64K alignment is detected.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
By default the SATA IP on the ls208Xa SoCs does not generating
coherent/snoopable transactions. This patch enable it in the
sata axicc register.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Set up chip power supply voltage according to voltage ID.
The fuse status register provides the values from on-chip
voltage ID fuses programmed at the factory. These values
define the voltage requirements for the chip.
Main operations:
1. Set up the core voltage
2. Set up the SERDES voltage and reset SERDES lanes
3. Enable/disable DDR controller support 0.9V if needed
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Without a prompt in Kconfig, SECURE_BOOT cannot be selected by
defconfig. The option was dropped unintentionally when defconfig
files were cleaned up. Three targets were impacted
ls1043ardb_SECURE_BOOT, ls2080ardb_SECURE_BOOT,
ls2080aqds_SECURE_BOOT.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch binds the sys_info->freq_systembus to Platform PLL, and
implements the IPs' clock function individually.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Up to now, there are 3 kind of SoCs under Layerscape Chassis 2,
like LS1043A, LS1046A and LS1012A. But the clocks tree has a
lot of differences, for instance, the IP modules have different
dividers to derive its clock from Platform PLL. And the core
cluster PLL and platform PLL maybe have different reference
clocks, such as LS1012A. Another problem is which clock/PLL
should be described by sys_info->freq_systembus, it is confused
in Layerscape Chissis 2.
This patch is to bind the sys_info->freq_systembus to the Platform
PLL, and handle the different divider of IP modules separately
between different SoCs, and separate reference clocks of core
cluster PLL and platform PLL.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Clear the content to zero and the ECC error bit of OCRAM1/2.
The OCRAM must be initialized to ZERO by the unit of 8-Byte before
accessing it, or else it will generate ECC error. And the IBR has
accessed the OCRAM before this initialization, so the ECC error
status bit should to be cleared.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Pratiyush Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
It is recommended to set forced-order mode in RNI-6,
RNI-20 for performance optimization in LS2088A.
Both LS2080A, LS2088A families has CONFIG_LS2080A define.
As above update is required only for LS2088A, skip this
for LS2080A SoC family.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Use option NUM_DDR_CONTROLLERS in ddr Kconfig and clean up existing
usage in ls102xa and fsl-layerscape. Remove all powerpc macros in
config header and board header files.
Signed-off-by: York Sun <york.sun@nxp.com>
Create driver/ddr/fsl/Kconfig and move existing options. Clean up
existing macros.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate sbc8641d, xpedite537x and MPC8536DS, run a moveconfig.py -s]
Signed-off-by: Tom Rini <trini@konsulko.com>
Instead of define CONFIG_SYS_FSL_SEC_COMPAT in header files for PowerPC
and ARM SoCs, move it to Kconfig under the driver.
Signed-off-by: York Sun <york.sun@nxp.com>
A most basic PSCI implementation with only one psci_version is added for
LS1043A, this can verify the generic PSCI framework, and more platform specific
implementation will be added later.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds secure_text, secure_data and secure_stack sections for ARMv8 to
hold PSCI text and data, and it is based on the legacy implementation of ARMv7.
ARMV8_SECURE_BASE defines the address for PSCI secure sections, ARMV8_PSCI and
ARMV8_PSCI_NR_CPUS are firstly used in this patch, so they are introduce here
in Kconfig too.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
NXP/Freescale uses macro CONFIG_ARMV8_PSCI to enable their private PSCI
implementation in PPA firmware, but this macro naming too generic, so this
patch replaces it with a specic one CONFIG_FSL_PPA_ARMV8_PSCI.
And this macro CONFIG_ARMV8_PSCI will be used for a generic PSCI for ARMv8
which will be added in following patchs.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The default configuration for QSPI AHB bus can't support 16MB+.
But some flash on NXP layerscape board are more than 16MB.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
- add additional function erratum_a009942_check_cpo to check if the
board needs tuning CPO calibration for optimal setting.
- move ERRATUM_A009942(with revision to check cpo_sample option) from
fsl_ddr_gen4.c to ctrl_regs.c for reuse on all DDR4/DDR3 parts.
- move ERRATUM_A008378 from fsl_ddr_gen4.c to ctrl_regs.c
- remove obsolete ERRATUM_A004934 which is replaced with ERRATUM_A009942.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
[YS: Replaced CONFIG_QEMU_E500 with CONFIG_ARCH_QEMU_E500]
Reviewed-by: York Sun <york.sun@nxp.com>
Spin-table method is used for secondary cores to load 32-bit OS. The
architecture information will be got through checking FIT image and
saved in the os_arch element of spin-table, then the secondary cores
will check os_arch and jump to 32-bit OS or 64-bit OS automatically.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
To support loading a 32-bit OS, the execution state will change from
AArch64 to AArch32 when jumping to kernel.
The architecture information will be got through checking FIT image,
then U-Boot will load 32-bit OS or 64-bit OS automatically.
Signed-off-by: Ebony Zhu <ebony.zhu@nxp.com>
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
NXP ARMv8 SoC LS2080A release all secondary cores in one-go.
But other new SoCs like LS2088A, LS1088A release secondary
cores one by one.
Update code to release secondary cores based on SoC SVR
Add code to release cores one by one for non LS2080A SoCs
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[YS: remove "inline" from declaration of initiator_type]
Reviewed-by: York Sun <york.sun@nxp.com>
The QorIQ LS2088A SoC is built on layerscape architecture.
It is similar to LS2080A SoC with some differences like
1)Timer controller offset is different
2)It has A72 cores
3)It supports TZASC module
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2080 SoC and its personalities does not support TZASC
But other new SoCs like LS2088A, LS1088A supports TZASC
Hence, skip initializing TZASC for Ls2080A based on SVR
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TZASC registers like TZASC_GATE_KEEPER, TZASC_REGION_ATTRIBUTES
are 32-bit regsiters.
So while doing register load-store operations, 32-bit intermediate
register, w0 should be used.
Update x0 register to w0 register type.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Timer controller base address has been changed from
LS2080A SoC (and its personalities) to new SoCs like
LS2088A, LS1088A.
Use SVR based timer base address detection to avoid compile time #ifdef.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Update CONFIG_LS2080A to CONFIG_FSL_LSCH3 to make those workaround
implementing of erratum reusable for more SoCs.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When implementing efi loader support, we can expose runtime services
for payloads. One such service is CPU reset.
This patch implements RTS CPU reset support for layerscape systems.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
The efi loader code has its own memory map, so it needs to be aware where
the spin tables are located, to ensure that no code writes into those
regions.
Signed-off-by: Alexander Graf <agraf@suse.de>
SoC-specific logic may be required for all forms of cache-wide
operations; invalidate and flush of both dcache and icache (note that
only 3 of the 4 possible combinations make sense, since the icache never
contains dirty lines). This patch adds an optional hook for all
implemented cache-wide operations, and renames the one existing hook to
better represent exactly which operation it is implementing. A dummy
no-op implementation of each hook is provided.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Move DDR3, DDR4 and realted options to Kconfig and clean up existing
uses.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move this option to Kconfig and clean up existing uses.
NUM_DDR_CONTROLLERS is also used by PowerPC SoCs.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move this option to Kconfig and clean up existing uses.
This option is also used by PowerPC SoCs.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move MAX_CPUS option to Kconfig and clean up existing uses for ARM. This
option is used by Freescale Layerscape SoCs.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move these options to Kconfig and create a sub-menu to avoid name
conflict with other architectures.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some config options should not have prompt. They are selected by choosing
target.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
SYSCLK is used as a reference clock for USB. When the USB controller
is used, SYSCLK must meet the additional requirement of 100 MHz.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Pin mux logic has 2 options in priority order, one is through RCW_SRC
and then through RCW_Fields. In case of QSPI booting, RCW_SRC logic
takes the priority for SPI pads and do not allow RCW_BASE and SPI_EXT
to control the SPI muxing. But actually those are DSPI controller's
pads instead of QSPI controller's, so this workaround allows RCW
fields SPI_BASE and SPI_EXT to control relevant pads muxing.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[York Sun: Reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
The core position is not continuous for some SoCs. For example,
valid cores may present at position 0, 1, 4, 5, 8, 9, etc. Some
registers (including boot release register) only count existing
cores. Current implementation of cpu_mask() complies with the
continuous numbering. However, command "cpu status" queries the
spin table with actual core position. Add functions to calculate
core position from core number, to correctly calculate offsets.
Tested on LS2080ARDB and LS1043ARDB.
Signed-off-by: York Sun <york.sun@nxp.com>
The exact SoC revsion number can be recognized from U-Boot log.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
By default the SATA IP on the ls1043a/ls1046a SoCs does not
generating coherent/snoopable transactions. This patch enable
it in the SCFG_SNPCNFGCR register along with sata axicc register.
In addition, the dma-coherent property must be set on the SATA
controller nodes.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
[York Sun: Reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
The default values for Port Phy2Cfg register and
Port Phy3Cfg register are better, no need to overwrite them.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Move this config to Kconfig option and clean up existing uses.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Calvin Johnson <calvin.johnson@nxp.com>
CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move this option to Kconfig and clean up existing uses.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Mingkai Hu <mingkai.hu@nxp.com>
CC: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
This is a workaround to fix SATA CRC error. Once the root cause
is found the ECC disabling will be removed.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As per the top level U-Boot README "Board Initialisation Flow"
section, board_init_f() should return without calling board_init_r()
directly. Clearing BSS and calling board_init_r() will be done in
crt0_64.S.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
According to design specification, the L2 cache operates at the same
frequency as the A72 CPUs in the cluster with a 3-cycle latency, so
increase the L2 Data RAM and Tag RAM latency to 3 cycles, or else,
will run into different call trace issues.
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As the access to serders protocol unselected PCIe controller will
hang. So disable the R/W permission to unselected PCIe controller
including its CCSR, IO space and memory space according to the
serders protocol field of RCW.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Move forward the basic non-secure access enable operation, so the
subsequent individual device access permission can override it.
And collect the dispersed callers in board level, and then move
them to SoC level.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Up to now, the function is_serdes_configed() doesn't check if the map
of serdes protocol is initialized before accessing it. The function
is_serdes_configed() will get wrong result when it was called before
the serdes protocol maps initialized. As the first element of the map
isn't used for any device, so use it as the flag to indicate if the
map has been initialized.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As part of Secure Boot Chain of trust, PPA image must be validated
before the image is started.
The code for the same has been added.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
DDR erratum A008336 only applies to DDR controller v5.2.0.
DDR controller v5.2.1 already has default 0x43b30002 in
EDDRTQCR1 register for optimal performance.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The PPA binary may be stored on QSPI flash instead of NOR.
So, deprecated CONFIG_SYS_LS_PPA_FW_IN_NOR in favour of
CONFIG_SYS_LS_PPA_FW_IN_XIP to prevent fragmentation of code
by addition of a new QSPI specific flag.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
MMU bit in SCTLR needs to be set explicitly after tables are
created. It isn't an issue for EL3 becuase this bit is already
set by early MMU setup. But for other exception levels this
bit was not set.
Signed-off-by: York Sun <york.sun@nxp.com>
The LS1046A processor is built on the QorIQ LS series architecture
combining four ARM A72 processor cores with DPAA 1.0 support.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Mihai Bantea <mihai.bantea@freescale.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
New SoC LS1046A belongs to Freescale Chassis Generation 2 and
has two SerDes so we need to add this support in fsl_lsch2.
The SoC related SerDes 2 support will be added in SoC patch.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support to detect Cortex-A72 core for printing it out.
The Initiator Version of A72 core should be 0x4.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
If the PSCI and PPA is ready, skip the fixup for spin-table and
waking secondary cores. Otherwise, change SMP method to spin-table,
and the device node of PSCI will be removed.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The FSL Primary Protected Application (PPA) is a software component
loaded during boot which runs in TrustZone and remains resident
after boot.
Use the secure firmware framework to integrate FSL PPA into U-Boot.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This function assume that the d-cache and MMU has been enabled earlier,
so it just created MMU table in main memory. But the assumption is not
always correct, for example, the early setup is done in EL3, while
enable_caches() is called when the PE has turned into another EL.
Define the function mmu_setup() for fsl-layerscape to cover the weak
one.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Drop platform code to create static MMU tables. Use common framework
to create MMU tables on the run. Tested on LS2080ARDB with secure and
non-secure ram scenarios.
Signed-off-by: York Sun <york.sun@nxp.com>
Secure_ram variable was put in generic global data. But only ARMv8
uses this variable. Move it to ARM specific data structure.
Signed-off-by: York Sun <york.sun@nxp.com>
Freescale ARMv8 SoC name ends with "A" to represent ARM SoCs.
like LS2080A, LS1043A, LS1012A.
So append "A" to SoC names.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The SPL code already knows which boot device it calls the spl_boot_mode()
on, so pass that information into the function. This allows the code of
spl_boot_mode() avoid invoking spl_boot_device() again, but it also lets
board_boot_order() correctly alter the behavior of the boot process.
The later one is important, since in certain cases, it is desired that
spl_boot_device() return value be overriden using board_boot_order().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[add newly introduced zynq variant]
Signed-aff-by: Andreas Bießmann <andreas@biessmann.org>
The register CLKCNCSR controls the frequency of all cores in the same
cluster.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This errata a008751 is applied on Soc specific file currently.This will be
moved to a file where all the errata implementation will take place for usb
for fsl. This patch removes the errata workaround from soc specific file
for LS2080.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Adds get_svr and IS_SVR_REV helpers for ARMv8 platforms,
similar to PPC and ARMv7.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Environment variable mcinitcmd is defined to initiate MC and DPL
deployment from the location where it is stored (NOR, NAND, SD, SATA,
USB) during booting. If this variable is not defined then macro
MC_BOOT_ENV_VAR will be null and MC will not be booted and DPL will
not be applied during U-boot booting.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The SP805-WDT module on LS2080A requires configuration of PMU's
PCTBENR register to enable watchdog counter decrement and reset
signal generation. The watchdog clock needs to be enabled first.
Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The QorIQ LS1012A processor, optimized for battery-backed or
USB-powered, integrates a single ARM Cortex-A53 core with a hardware
packet forwarding engine and high-speed interfaces to deliver
line-rate networking performance.
This patch add support of LS1012A SoC along with
- Update platform & DDR clock read logic as per SVR
- Define MMDC controller register set.
- Update LUT base address for PCIe
- Avoid L3 platform cache compilation
- Update USB address, errata
- SerDes table
- Added CSU IDs for SDHC2, SAI-1 to SAI-4
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Makarand Pawagi <makarand.pawagi@mindspeed.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
SoC overviews are getting repeated across board folders.
So, Organize SoC overview at common location i.e. fsl-layerscape/doc
Also move README.lsch2 and README.lsch3 in same folder.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch2_speed.c: In function
‘get_sys_info’:
arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch2_speed.c:29:6: warning:
unused variable ‘rcw_tmp’ [-Wunused-variable]
u32 rcw_tmp;
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Other than LS1043A, LS1012A also Chassis Gen2 Architecture compliant.
So Avoid LS1043A specific defines in arch/arm
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
It is not mandatory for Layerscape SoCs to have SMMU. SoCs like
LS1012A are layerscape SoC without SMMU IP.
So put SMMU configuration code under SMMU_BASE.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
MMCSD_MODE_FAT has be renmaed to MMCSD_MODE_FS by commit 205b4f33.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
init_early_memctl_regs() is also be called in board_early_init_f().
So remove the duplicated call in spl code.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As the issue about the stack will get corrupted when switching between
the early and final mmu tables is fixed by commit 70e21b064, the
workaround to flush dcache is unnecessary and should be removed.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For Qoriq PPC&ARM v7 platforms, the crypto node is being fixup'ed in
order to update the SEC internal version (aka SEC ERA). This patch
adds the same functionality to the ARMv8 SoCs.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Barrier transactions from CCI400 need to be disabled till
the DDR is configured, otherwise it may lead to system hang.
The patch adds workaround to fix the erratum.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2080A is the primary SoC, and LS2085A is a personality with AIOP
and DPAA DDR. The RDB and QDS boards support both personality. By
detecting the SVR at runtime, a single image per board can support
both SoCs. It gives users flexibility to swtich SoC without the need
to reprogram the board.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
During secure boot, SMMU is enabled on POR by SP bootrom. SMMU needs
to be put in bypass mode in uboot to enable CAAM transcations to pass
through.
For non-secure boot, SP BootROM doesn't enable SMMU, which is in
bypass mode out of reset.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The qspi_cfg register is set by PBI when booting from QSPI. No need
to changing it again.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The eSDHC could select to use platform clock or peripheral clock to
generate SD clock. The default selection is platform clock. So, fix
the clock frequency value that's calculated for eSDHC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The serdes protocol entries in Serdes table 1 for protocol
0x03, 0x33, 0x35 and in Serdes table 2 for protocols 0x45
and 0x47 are updated to reflect the entries in
current Reference Manual.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Reported-by: Jose Rivera <german.rivera@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove stream ID partitioning support that has been made
obsolete by upstream device tree bindings that specify how
representing how PCI requester IDs are mapped to MSI specifiers
and SMMU stream IDs.
Signed-off-by: Stuart Yoder <stuart.yoder@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Enable wuo config to accelerate coherent ordered writes for LS2080A
and LS2085A.
WRIOP IP is connected to RNI-20 Node.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
With commit 7985cdf we converted all systems except for the Layerscape
SoCs to the generic descriptor table based page table setup.
On the Layerscape SoCs however, we just provide an empty table stub
and do the setup ourselves. To reserve enough memory for the tables,
we need to override the default counting mechanism which would end up
with an empty table because we have no maps.
Fixes: 7985cdf
Reported-by: York Sun <york.sun@nxp.com>
CC: Alison Wang <alison.wang@nxp.com>
CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: York Sun <york.sun@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
By now the code to only have a single page table level with 64k page
size and 42 bit address space is no longer used by any board in tree,
so we can safely remove it.
To clean up code, move the layerscape mmu code to the new defines,
removing redundant field definitions.
Signed-off-by: Alexander Graf <agraf@suse.de>
Memory controller performance is not optimal with default internal
target queue register value, write required value for optimal DDR
performance.
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QSPI and IFC are pin-multiplexed on LS1043A. So we use
ls1043aqds_sdcard_ifc_defconfig to support IFC in SD boot and
ls1043aqds_sdcard_qspi_defconfig to support QSPI in SD boot.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Chain of Trust is enabled for ARM platforms (LS1021 and LS1043).
In board_late_init(), fsl_setenv_chain_of_trust() is called which
will perform the following:
- If boot mode is non-secure, return (No Change)
- If boot mode is secure, set the following environmet variables:
bootdelay = 0 (To disable Boot Prompt)
bootcmd = CONFIG_CHAIN_BOOT_CMD (Validate and execute Boot script)
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2080A has support for 8 DPMAC ports out of which
only 5 ports can be used at a time.
Enabling all 8 DPMAC ports of LS2080A personality.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Acked-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
SYSCLK frequency is dependent on on-board switch settings. It may
vary as per requirement. boot-loader is aware of board switch
configurations.
So Fixup Linux device tree from boot-loader.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
CC: Mingkai Hu <Mingkai.Hu@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Consecutive write transactions from core to PCI express outbound
path hangs after 25 to 30 transactions depending on core freq.
This erratum enable the mbist clock through COP register setting.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale ARM-based Layerscape contains a SATA controller
which comply with the serial ATA 3.0 specification and the
AHCI 1.3 specification.
This patch adds SATA feature on ls2080aqds, ls2080ardb and
ls1043aqds boards.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For LS1043, SEC read/writes are made snoopable by setting
the corresponding bits in SCFG to avoid coherency issues.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
MC and debug server are not board-specific. Move reserving memory to SoC
file, using the new board_reserve_ram_top function. Reduce debug server
memory by 2MB to make room for secure memory.
In the system with MC and debug server, the top of u-boot memory
is not the end of memory. PRAM is not used for this reservation.
Signed-off-by: York Sun <yorksun@freescale.com>
DDR has been set as secure in MMU tables. Non-secure master such
as SDHC DMA cannot access data correctly. Mixing secure and non-
secure MMU entries requirs the MMU tables themselves in secure
memory. This patch moves MMU tables into a secure DDR area.
Early MMU tables are changed to set DDR as non-secure. A new
table is added into final MMU tables so secure memory can have
2MB granuality.
gd->secure_ram tracks the location of this secure memory. For
ARMv8 SoCs, the RAM base is not zero and RAM is divided into several
banks. gd->secure_ram needs to be maintained before using. This
maintenance is board-specific, depending on the SoC and memory
bank of the secure memory falls into.
Signed-off-by: York Sun <yorksun@freescale.com>
As the errata A008336 and A008514 do not apply to all LS series SoCs
(such as LS1021A, LS1043A) we move them to an soc specific file
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
GCC 5.x does not like sizeof(array_variable) and errors out. Change these
calls to be instead sizeof(u8) (as that's what serdes_prtcl_map is) *
SERDES_PRCTL_COUNT (the number of array elements).
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <yorksun@freescale.com>
If the core runs at higher than x3 speed of the platform, there is
possiblity about sev instruction to getting missed by other cores.
This is because of SoC Run Control block may not able to sample
the EVENTI(Sev) signals.
Configure Run Control and EPU to periodically send out EVENTI signals to
wake up A57 cores.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When one core is released, other cores may not have valid entry
address. Those cores are trapped by "wfe" and wait for further
instruction. When their address is set, they need to be kicked
off by "sev".
Signed-off-by: York Sun <yorksun@freescale.com>
For most device addresses excution shouldn't be allowed. Revise
the MMU table to enforce execute-never bits. OCRAM, DDR and IFC
are allowed for excution.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reported-by: Zhichun Hua <zhichun.hua@freescale.com>
The global_data pointer (gd) has been set earlier in crt0_64.S.
So there's no need to assign it again. Remove gdata since it is going
away in U-Boot.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale's LS2085A is a another personality of LS2080A SoC with
support of AIOP and DP-DDR.
This Patch adds support of LS2085A Personality.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Updated MAINTAINERS files
Dropped #ifdef in cpu.h
Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP
personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc.
So renaming existing LS2085A code base to reflect LS2080A (Prime personality)
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Dropped #ifdef in cpu.c for cpu_type_list]
Reviewed-by: York Sun <yorksun@freescale.com>
Management complex Firmware, DPL and DPC are depolyed during u-boot boot
sequence.
Add new DPAA2 commands to manage Management Complex (MC) i.e. start mc, aiop
and apply DPL from u-boot command prompt.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Current implementation only consider SGMIIs for dpmac initialization.
XFI serdes protocols also uses dpmac.
Also, fix lane protocol parsing logic to consider both XFIs and SGMIIs.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
After the secondary cores enter U-Boot, use CONFIG_ARMV8_MULTIENTRY to
make secondary cores excute in spin loop.
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds esdhc support for ls1043ardb.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LS1043ARDB Specification:
-------------------------
Memory subsystem:
* 2GByte DDR4 SDRAM (32bit bus)
* 128 Mbyte NOR flash single-chip memory
* 512 Mbyte NAND flash
* 16 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
Ethernet:
* XFI 10G port
* QSGMII with 4x 1G ports
* Two RGMII ports
PCIe:
* PCIe2 (Lanes C) to mini-PCIe slot
* PCIe3 (Lanes D) to PCIe slot
USB 3.0: two super speed USB 3.0 type A ports
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Freescale LayerScape with Chassis Generation 2 is a set of SoCs with
ARMv8 cores and 2rd generation of Chassis.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
There are two LS series processors are built on ARMv8 Layersacpe
architecture currently, LS2085A and LS1043A. They are based on
ARMv8 core although use different chassis, so create fsl-layerscape
to refactor the common code for the LS series processors which also
paves the way for adding LS1043A platform.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
