dev_err has been used for debugging and a few dev_err message are
printed for normal code execution. Make them dev_dbg instead.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
By using a hypervisor call, we can implement DEBUG_UART on xen.
This will allow us to see messages even earlier than serial_init().
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
At present, DM_FLAG_PRE_RELOC is set only if !OF_CONTROL.
It doesn't make sense for this para-virtualized driver.
With this patch applied, you will be able to see early boot messages:
U-Boot 2020.10-00001-ge442e71a6c52-dirty (Oct 15 2020 - 11:02:25 +0900)
xenguest
Xen virtual CPU
Model: XENVM-4.15
DRAM: 128 MiB
PVBLOCK:
(XEN) gnttab_mark_dirty not implemented yet
pvblock: 0
In: hypervisor
Out: hypervisor
Err: hypervisor
xenguest#
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
1. Rename AST2500 reset driver from ast2500-reset.c
to reset-ast2500.c
2. Rename AST2500 reset kconfig option from AST2500_RESET
to RESET_AST2500
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
The System Control Unit (SCU) controller of Aspeed
SoCs provides the reset control for each peripheral.
This patch refactors the reset method to leverage
the SCU reset control. Thus the driver dependency
on watchdog including dedicated WDT API and reset
flag encoding can be eliminated.
The Kconfig description is also updated accordingly.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
The 12d152620d commit fixed the get_rate helper because the set_parent
one did not re-parent the clock device to the new parent. The 4d139f3838
commit allows you to remove this workaround by calling the
clk_get_parent_rate routine.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Add support for the hardware pseudo random number generator found in Qualcomm SoC-s.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This adds the driver for the IPQ40xx built-in MDIO.
This will be needed to support future PHY driver.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds support for the Qualcomm QUP SPI controller that is commonly found in most of Qualcomm SoC-s.
Driver currently supports v1.1.1, v2.1.1 and v2.2.1 HW.
FIFO and Block modes are supported, no support for DMA mode is planned.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
No timer drivers return an error from get_count. Instead of possibly
returning an error, just return the count directly.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The sandbox is built with the SDL2 library with invokes the X11 library
which in turn calls getc(). But getc() in glibc is defined as
int getc(FILE *)
This does not match our definition.
int getc(void)
The sandbox crashes when called with parameter -l.
Rename our library symbol getc() to getchar().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We don't want the debug output to be visible in a normal boot. Silence it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher<hs@denx.de>
This function can be called when it is not known whether it will find
anything. This results in confusing log messages if the device is not
found. It is better for the caller to log the failure, if necessary.
Drop the logging from this function.
Signed-off-by: Simon Glass <sjg@chromium.org>
- Fix stm32prog command: parsing of FlashLayout without partition
- Update MAINTAINERS for ARM STM STM32MP
- Manage eth1addr on dh board with KS8851
- Limit size of cacheable DDR in pre-reloc stage in stm32mp1
- Use mmc_of_parse() to read host capabilities in mmc:sdmmc2 driver
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl+QXvgACgkQ4rK92eCq
k3Vbrgf/cBKPY9bS+lJVARgjDvIOdcXzpgH/F7dUlq+dzu/mCwhIBVKxM7/nXh5p
RhfGET2fpMYY/41LkKza7AqOiGTXZG4pTmCGe1UHXrXeIPjinWG1LQjU/KOk6U4n
681P9BZfTUXrVgzLBIUY1KBFVyMaiYfVjxU3MnA1vqrubymFbf+IpUt3OIegUDCp
AjrTdj7sFEQ3nG/pgTyqFCwkl/MG53aB9MiaBBRxeGHYnDn0qzAEHSGqzSZZGhNl
1ubJDF3K7w6Pj3MzIeA80M5r0fJoTy/qWcNH31psOpyQaHJ9NbPGjFYE6AkDPV4l
27QN71AcRtCzlv1XQpblA98pa1bUYw==
=Bl3G
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20201021' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Activate CMD_EXPORTENV/CMD_IMPORTENV/CMD_ELF for STM32MP15 defconfig
- Fix stm32prog command: parsing of FlashLayout without partition
- Update MAINTAINERS for ARM STM STM32MP
- Manage eth1addr on dh board with KS8851
- Limit size of cacheable DDR in pre-reloc stage in stm32mp1
- Use mmc_of_parse() to read host capabilities in mmc:sdmmc2 driver
When sending a command via the MDIO bus, the Designware MAC expects some
bits in the CMD register to describe the clock divider value between
the main clock and the MDIO clock.
So far we were omitting these bits, resulting in setting "00", which
means "/ 16", so ending up with an MDIO frequency of either 18.75 or
12.5 MHz.
All the internal PHYs in the H3/H5/H6 SoCs as well as the Gbit Realtek
PHYs seem to be fine with that - although it looks like to be severly
overclocked (the MDIO spec limits the frequency to 2.5 MHz).
However the external 100Mbit PHY on the Pine64 (non-plus) board is
not happy with that, Ethernet was actually never working there, as the
PHY didn't probe.
As we set the EMAC clock (via AHB2) to 300 MHz in ATF (on the 64-bit
SoCs), and use 200 MHz on the H3, we need the highest divider of 128
to let the MDIO clock end up below the required 2.5 MHz.
This enables Ethernet on the Pine64(non-plus).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The current implementation of sun8i_get_ephy_nodes() makes quite some
assumptions, in general relying on DT path names is a bad idea.
I think the idea of the code was to determine if we are using the
internal PHY, for which there are simpler and more robust methods:
Rewrite (and rename) the existing function to simply lookup the DT node
that "phy-handle" points to, using the device's DT node.
Then check whether the parent of that PHY node is using an "H3 internal
MDIO" compatible string. If we ever get another internal MDIO bus
implementation, we will probably need code adjustments anyway, so this
is good enough for now.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[jagan: rebase on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The error handling in recv() is somewhat broken, for instance
good_packet isn't really used, and it's hardly readable. Also we try
to check for short or too big packets, but those are actually filtered
out by the hardware.
Simplify the whole routine and improve the error handling:
- Bail out early if the current RX descriptor is not ready.
- Enable propagation of runt, huge and broken packets.
- Check for runt and huge packets, and return 0 to indicate this.
This will force the framework to call free_pkt for cleanup.
- Avoid aligning the packet buffer for invalidation again.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The EMAC soft reset routine was subtly broken, using an open coded
timeout routine without any actual delay.
Remove the unneeded initial reset bit read, and call wait_for_bit_le32()
to handle the timeout correctly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When iterating over all RX/TX buffers, we were using a rather long "idx"
control variable, which lead to a nasty overlong line.
Replace "idx" with "i" to avoid this.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
To meet the current alignment requirements for our cache maintenance
functions, we were explicitly aligning the *arguments* to those calls.
This is not only ugly to read, but also wrong, as we need to make sure
we are not accidentally stepping on other data.
Provide wrapper functions for the common case of cleaning or
invalidating a descriptor, to make the cache maintenance calls more
readable. This fixes a good deal of the problematic calls.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
There is no reason to invalidate a TX descriptor before we are setting
it up, as we will only write to a field.
Remove the not needed invalidate_dcache_range() call.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When we initialise the TX descriptors, there is no need yet to clean
them all to memory, as they don't contain any data yet. Later we will
touch and clean each descriptor anyway.
However we tell the MAC about the beginning of the chain, so we have to
clean at least the first descriptor, to make it clear that this is empty
and there are no packets to transfer yet.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Before we initialise the RX descriptors, there is no need to *clean*
them from the cache, as we touch them for the first time.
However we should cover the case that those buffers contain dirty cache
lines, which could be evicted and written back to DRAM any time later,
in the worst case *after* the MAC has transferred a packet into them.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The EMAC driver contains a lot of magic bits, although the manuals
and the Linux driver have all names for them.
Define those names and use them when programming the registers.
Also this replaces a lot of readl/mask/writel operations with the much
easier-to-read setbits_le32() macro.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Apparently due to copying from some older or converted driver, the
sun8i_emac driver contains pointless wrapper functions to bridge
between a legacy driver and the driver model.
Since sun8i_emac is (and always was) driver model only, there is no
reason to have those confusing wrappers. Just remove them, and use
the driver model prototypes directly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When preparing the register value for the MDIO command register, we
start with a zeroed register, so there is no need to mask off certain
bits before setting them.
Simplify the sequence, and rename the variable to a more matching
mii_cmd on the way.
Also the open-coded time-out routine can be replaced with a much safer
and easier-to-read call to wait_for_bit_le32().
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When initialising the TX DMA descriptors, we mostly chain them up,
but of course don't know about any data or its length yet.
That means they are still invalid, and the OWN bit should NOT be set
yet.
In fact when we later tell the MAC about the beginning of the chain,
and enable TX DMA in the start() routine, the MAC will start fetching
TX descriptors prematurely, as it can be seen by dumping the TX_DMA_STA
and TX_DMA_CUR_DESC registers.
Clear the owner bit, to not give the MAC the wrong illusion that it
owns the descriptors already.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When phy_startup() returns with an error, because there is no link or
the user interrupted the process, we shall stop the _start() routine
and return with an error, instead of proceeding anyway.
This fixes pointless operations when there is no Ethernet cable
connected, for instance.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Amit Singh Tomar <amittomer25@gmail.com> # Pine64+
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cosmetic update of gpio.h:
- remove enumerate: stm32_gpio_port, stm32_gpio_pin
because STM32_GPIO_XXX values are unused
- move STM32_GPIOS_PER_BANK in stm32_gpio.c
as its value is IP dependent and not arch dependent
No functional change as number of banks and number of gpio by banks
is managed by device tree since since DM migration and
commit 8f651ca60b ("pinctrl: stm32: Add get_pins_count() ops").
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
mmc_of_parse() can populate the 'f_max' and 'host_caps' fields of
struct mmc_config from devicetree.
The same logic is duplicated in stm32_sdmmc2_probe(). Use
mmc_of_parse(), which is more generic.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
"cap-mmc-highspeed" enables support for 26 MHz MMC, but there is no
additional flag to enable 52 MHz MMC. In Linux. "cap-mmc-highspeed"
is used for MMC HS at both 26MHz and 52MHz.
Use the same approach and enable MMC_CAP(MMC_HS_52) host capability
when "cap-mmc-highspeed" is found in the devicetree. In the event an
MMC card doesn't support 52 MHz, it will be clocked at a speed based
on its EXT CSD, even on 52 MHz host controllers
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Sync the R8A77990 SoC PFC tables with Linux 5.9 , commit bbf5c979011a.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
This sync's the RZ/G2H clock tables with mainline linux 5.9 commit
bbf5c979011a ("Linux 5.9").
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
This sync's the RZ/G2N clock tables with mainline linux 5.9 commit
bbf5c979011a ("Linux 5.9").
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Add fallback compatibility string for R-Car Gen3 and RZ/G2.
Also sorted the compatible string as per SoC ID.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Add an entry in usb_gadget_controller_number() for the MTU3
gadget controller. It is used to bind the USB Ethernet driver.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch adds support for the MediaTek USB3 DRD controller,
its host side is based on xHCI, this driver supports device mode
and host mode.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
There is only declaration of usb_speed_string(), but no definition,
so add it to avoid build error when call it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
In buffer DMA mode, gadget should re-configure EP 0 to received SETUP
packets when doeptsiz.xfersize is equal to a setup packet size(8 bytes)
and EP 0 is in WAIT_FOR_SETUP state.
Since EP 0 is not enabled in WAIT_FOR_SETUP state, SETUP packets is NOT
received from RxFifo and wriiten to the external memory.
Signed-off-by: Chance.Yang <chance.yang@vatics.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl+NMmQcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyLnEB/0cWFfjDfCMY1o7R4QX
DeDRlD6k6acQWlwa5EiRKwpbPMJKrSI/m5alMCYZG6YHvGtzihqnqohz3gl1sepi
W7eyyyFsM4hqe4P3lSETJRGWe/O8bNkoa0hBzqZ9btqw2OJLBu4JYB+zKgz8kaDY
jzkGLgaaK6wtG3rEu+q4fjzp1y9kuz31WnN+9qS8jd/9UH13XKCkJl9TfY5pLfgc
mmbn2NWtAhi91uShcnIsOpLaNm23IV0ITa22etB9F1docZuUrbhOtiIF45AADjpG
/xtkV3dEVGml3N/17RizgOwxX3xughG0ak9xifsK6tfgqfVhaGMgkToNNBM+1ddm
rZZM
=hF12
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.01-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.01 cycle:
This feature set brings the rework of the clock tree for sam9x60 SoC.
This makes the clock tree fully compatible with Common Clock Framework
and allows full clock configuration in U-Boot. This means that the
sam9x60 boards can boot now using U-Boot.
This also includes the definitions for sam9x60 SiPs and a divisor fix
for the clock on sama7g5 SoC.
This SoC has the 5th divisor for the mck0 master clock.
Adapt the characteristics accordingly.
Reported-by: Mihai Sain <mihai.sain@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
clk-master can have 5 divisors with a field width of 3 bits
on some products.
Change the mask and number of divisors accordingly.
Reported-by: Mihai Sain <mihai.sain@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Done with:
./tools/moveconfig.py VIDEO_BMP_GZIP
The 3 suspicious migration because CMD_BMP and SPLASH_SCREEN
are not activated in these defconfigs:
- trats_defconfig
- s5pc210_universal_defconfig
- trats2_defconfig
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For levels equal to the maximum value, the duty cycle must be equal to
the period.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Amlogic D-PHY in the Amlogic AXG SoC Family does support a frequency
higher than 10MHz for the TX Escape Clock, thus make the target rate
configurable.
This is based on the Linux commit [1] and adapted to the U-Boot driver.
[1] a328ca7e4af3 ("drm/bridge: dw-mipi-dsi: permit configuring the escape clock rate")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The timing values for dw-dsi are often dependent on the used display and
according to Philippe Cornu will most likely also depend on the used phy
technology in the soc-specific implementation.
To solve this and allow specific implementations to define them as needed
add a new get_timing callback to phy_ops and call this from the dphy_timing
function to retrieve the necessary values for the specific mode.
This is based on the Linux commit [1] and adapted to the U-Boot driver.
[1] 25ed8aeb9c39 ("drm/bridge/synopsys: dsi: driver-specific configuration of phy timings")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This driver doesn't use DM (in the correct places), so we use a device and
not a udevice. We also need to include device_compat.h
Signed-off-by: Sean Anderson <seanga2@gmail.com>
This patch enhances the Octeon TX/TX2 watchdog driver to fully enable
the WDT. With this changes, the "wdt" command is now also supported
on these platforms.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Suneel Garapati <sgarapati@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Remove a left-over debug test message from the Octeon TX / TX2
MMC driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Suneel Garapati <sgarapati@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Octeon TX2 sets the TB100_EN bit in the config register. We need to use
a fixed 100MHz clock for this as well to work properly.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Suneel Garapati <sgarapati@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
- fsl_esdhc_imx cleanup
- not send cm13 if send_status is 0.
- Add reinit API
- Add mmc HS400 for fsl_esdhc
- Several cleanup for fsl_esdhc
- Add ADMA2 for sdhci
- Octeon TX: Add NAND driver (Suneel)
- Octeon TX: Add NIC driver driver (Suneel)
- Octeon TX2: Add NIC driver driver (Suneel)
- Armada 8040: Add iEi Puzzle-M80 board support (Luka)
- Armada A37xx SPI: Add support for CS-GPIO (George)
- Espressobin: Use Linux model/compatible strings (Andre)
- Espressobin: Add armada-3720-espressobin-emmc.dts from Linux (Andre)
- Armada A37xx: Small cleanup of config header (Pali)
Set the defaults on probe for the packet buffer size registers
for the i210.
The TX/RX PBSIZE register of the i210 resets to its default value
only at power-on - see Intel Ethernet Controller I210 Datasheet rev 3.5
chapter 8.3 'Internal Packet Buffer Size Registers'.
If something (another driver, another OS, etc.) modifies this register
from its default value, the e1000 driver doesn't function correctly. It
detects a hang of the transmitter and continuously resets the adapter.
Here we set this value to its default when resetting the i210 to
resolve this issue.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
CONFIG_IS_ENABLED() takes the kconfig name without the CONFIG_ prefix,
e.g. CONFIG_IS_ENABLED(CLK) for CONFIG_CLK. Some of these were being
fixed every now and then, see:
commit 71ba2cb0d6 ("board: stm32mp1: correct CONFIG_IS_ENABLED usage for LED")
commit a5ada25e42 ("rockchip: clk: fix wrong CONFIG_IS_ENABLED handling")
commit 5daf6e56d3 ("common: console: Fix duplicated CONFIG in silent env callback")
commit 48bfc31b64 ("MIPS: bootm: Fix broken boot_env_legacy codepath")
Fix all files found by `git grep "CONFIG_IS_ENABLED(CONFIG"` by running
':%s/CONFIG_IS_ENABLED(CONFIG_\(\w+\))/CONFIG_IS_ENABLED(\1)/g' in vim.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since it's so trivial I could just about tolerate this when there were only
two copies of it. But now there are about to be three.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
For testing purposes keep the output value when switching to input.
This allows us to manipulate the input value via the gpio command.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Newer eSDHC controllers support ADMA2 descriptor tables which support
64bit DMA addresses. One notable user of addresses in the upper memory
segment is the EFI loader.
If support is enabled, but the controller doesn't support ADMA2, we
will fall back to SDMA (and thus 32 bit DMA addresses only).
Signed-off-by: Michael Walle <michael@walle.cc>
The device tree has a way to specify GPIO lines as chip selects. From
the binding docs:
So if for example the controller has 2 CS lines, and the cs-gpios
property looks like this:
cs-gpios = <&gpio1 0 0> <0> <&gpio1 1 0> <&gpio1 2 0>;
Then it should be configured so that num_chipselect = 4 with the
following mapping:
cs0 : &gpio1 0 0
cs1 : native
cs2 : &gpio1 1 0
cs3 : &gpio1 2 0
Add support for this, while retaining backward-compatibility with
existing device trees; the driver will preserve existing behavior if a
cs-gpios list is not given, or if a particular line is specified as <0>
(native).
This implementation is inspired by similar implementations in
neighboring drivers for other platforms: atmega, mxc, etc.
Signed-off-by: George Hilliard <ghilliar@amazon.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Adds support for Network Interface controllers found on
OcteonTX2 SoC platforms.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Adds support for Network Interface controllers found on
OcteonTX SoC platforms.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Adds support for NAND controllers found on OcteonTX or
OcteonTX2 SoC platforms. Also includes driver to support
Hardware ECC using BCH HW engine found on these platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
- Minor cleanup on K3 env variables
- Fix OSPI compatible for J721e
- Drop unused property in omap-usb2-phy
- Update Maintainer for am335x-guardian board.
Currently, readl/writel and esdhc_read32/esdhc_write32 are used. To align
the usage, change to only use esdhc_read32/esdhc_write32.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
There are other (non-SDHCI) controllers which supports ADMA2 descriptor
tables, namely the Freescale eSDHC. Instead of copying the code, move it
into an own module.
Signed-off-by: Michael Walle <michael@walle.cc>
First, we need the waterlevel setting for PIO mode only. Secondy, both DMA
setup code is identical for both directions, except for the data pointer.
Thus, unify them.
Signed-off-by: Michael Walle <michael@walle.cc>
Use the dma_{map,unmap}_single() calls. These will take care of the
flushing and invalidation of caches.
Signed-off-by: Michael Walle <michael@walle.cc>
SDMA can only do DMA with 32 bit addresses. This is true for all
architectures (just doesn't apply to 32 bit ones). Simplify the code and
remove unnecessary CONFIG_FSL_LAYERSCAPE.
Also make the error message more concise.
Signed-off-by: Michael Walle <michael@walle.cc>
This 1ms delay before sending command already exist from the beginning
of the fsl_esdhc driver added in year 2008. Now this driver has been
split for two files: fsl_esdhc.c and fsl_esdhc_imx.c. fsl_esdhc_imx.c
only for i.MX series. i.MX series esdhc/usdhc do not need this 1ms delay
before sending any command. So remove this 1ms, this will save a lot
time if handling a large mmc data.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
According to the code logic in __mmc_switch, if the parameter 'send_status'
is zero, no need to send cmd13, just wait the stated timeout time, then
can return directly.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
There was a fix-up for eMMC HS400 stability issue in Linux.
Patch link:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/
commit/?id=58d0bf843b49fa99588ac9f85178bd8dfd651b53
Description:
Currently only LX2160A eSDHC supports eMMC HS400. According to
a large number of tests, eMMC HS400 failed to work at 150MHz,
and for a few boards failed to work at 175MHz. But eMMC HS400
worked fine on 200MHz. We hadn't found the root cause but
setting eSDHC_DLLCFG0[DLL_FREQ_SEL] = 0 using slow delay chain
seemed to resovle this issue. Let's use this as fixup for now.
Introduce the fix-up in u-boot since the issue could be reproduced
in u-boot too.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Fix mmc->clock with actual clock which is divided by the
controller, and record it with priv->clock which was removed
accidentally.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The process for eMMC HS400 mode for eSDHC is,
1. Perform the Tuning Process at the HS400 target operating frequency.
Latched the clock division value.
2. if read transaction, then set the SDTIMNGCTL[FLW_CTL_BG].
3. Switch to High Speed mode and then set the card clock frequency to
a value not greater than 52Mhz
4. Clear TBCTL[TB_EN],tuning block enable bit.
5. Change to 8 bit DDR Mode
6. Switch the card to HS400 mode.
7. Set TBCTL[TB_EN], tuning block enable bit.
8. Clear SYSCTL[SDCLKEN]
9. Wait for PRSSTAT[SDSTB] to be set
10. Change the clock division to latched value.Set TBCTL[HS 400 mode]
and Set SDCLKCTL[CMD_CLK_CTRL]
11. Set SYSCTL[SDCLKEN]
12. Wait for PRSSTAT[SDSTB] to be set
13. Set DLLCFG0[DLL_ENABLE] and DLLCFG0[DLL_FREQ_SEL].
14. Wait for delay chain to lock.
15. Set TBCTL[HS400_WNDW_ADJUST]
16. Again clear SYSCTL[SDCLKEN]
17. Wait for PRSSTAT[SDSTB] to be set
18. Set ESDHCCTL[FAF]
19. Wait for ESDHCCTL[FAF] to be cleared
20. Set SYSCTL[SDCLKEN]
21. Wait for PRSSTAT[SDSTB] to be set.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Add a mmc_hs400_prepare_ddr() interface for controllers
which needs preparation before switching to DDR mode for
HS400 mode.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Some controllers may have difference between HS200 tuning
and HS400 tuning, such as different registers setting,
different procedure, or different errata.
This patch is to add a hs400_tuning flag to identify the
tuning for HS400 mode.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
For DM_MMC, the controller re-initialization is needed to
clear old configuration for mmc rescan.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
"ti,dis-chg-det-quirk" property is not part of Linux kernel DT binding
documentation. Therefore drop this and instead use soc_device_match()
to distinguish b/w AM654 SR1.0 and SR2.0 devices similar to Linux kernel
driver.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reset the channel completely during channel release in order to clear
teardown bit before handing over to next user or jumping to Linux.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Enable FPGA full reconfiguration support with Intel FPGA SDM
Mailbox driver for Agilex.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Ensure watchdog reset is not triggered if the fpga
reconfiguration is taking too long.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Rename Stratix10 FPGA driver to Intel FPGA SDM Mailbox driver
because it is using generic SDM (Secure Device Manager) Mailbox
interface shared by other platform (e.g. Agilex) as well.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Rename the driver from S10 to SoC64 because Intel Agilex platform
also using the this SYSRESET SoCFPGA driver for S10.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add additional membus writes to configure main and peripheral PLL
for Agilex's clock manager.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Since warm reset may optionally set the CLock Manager to'boot mode',
the clock driver should always force the Agilex's Clock Manager to
'boot mode' before the clock driver start configuring the Clock Manager
in SPL.
In SSBL, clock driver will skip the Clock Manager configuration
if it's already being setup by SPL (Clock Manager NOT in 'boot
mode') to prevent any inaccurate clocking issues happened on HPS
peripherals such as UART, MAC and etc.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Some drivers probing failed if clock enable function is not supported in
clock driver. So, add clock enable function to clock driver to solve it.
Return 0 (success) for *.enable function because all clocks are enabled
by default in clock driver probe.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
The timeout calculation is based on the clk being in KHz but
the clk api returns the clk value in Hz. Convert this to KHz
to calculate the correct timeout value.
Signed-off-by: Jack Mitchell <ml@embed.me.uk>
This more closely mirrors Linux's behaviour, and will make it easier to
transition to using function+color in the future.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
dm_gpio_ops.get_value can be called when the gpio is either input or
output. The current dw code always returns the input value, which is
invalid if the direction is set to out.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Previously, if there was no bank-name property, it was easy to have
confusing gpio names like "gpio1@08", instead of "gpio1@0_8". This patch
follows the example of the sifive gpio driver.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Change the type of gpio_dwabp_platdata.base from fdt_addr_t to a void
pointer, since we pass it to readl.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Fully-Programmable Input/Output Array (FPIOA) device controls pin
multiplexing on the K210. The FPIOA can remap any supported function to any
multifunctional IO pin. It can also perform basic GPIO functions, such as
reading the current value of a pin. However, GPIO functionality remains
largely unimplemented (in favor of the dedicated GPIO peripherals).
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This extends the pinctrl-sandbox driver to support pin muxing, and adds a
test for that behaviour. The test is done in C and not python (like the
existing tests for the pinctrl uclass) because it needs to call
pinctrl_select_state. Another option could be to add a command that
invokes pinctrl_select_state and then test everything in
test/py/tests/test_pinmux.py.
The pinctrl-sandbox driver now mimics the way that many pinmux devices
work. There are two groups of pins which are muxed together, as well as
four pins which are muxed individually. I have tried to test all normal
paths. However, very few error cases are explicitly checked for.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The pinmux property allows for smaller and more compact device trees,
especially when there are many pins which need to be assigned individually.
Instead of specifying an array of strings to be parsed as pins and a
function property, the pinmux property contains an array of integers
representing pinmux groups. A pinmux group consists of the pin identifier
and mux settings represented as a single integer or an array of integers.
Each individual pin controller driver specifies the exact format of a
pinmux group. As specified in the Linux documentation, a pinmux group may
be multiple integers long. However, no existing drivers use multi-integer
pinmux groups, so I have chosen to omit this feature. This makes the
implementation easier, since there is no need to allocate a buffer to do
endian conversions.
Support for the pinmux property is done differently than in Linux. As far
as I can tell, inversion of control is used when implementing support for
the pins and groups properties to avoid allocating. This results in some
duplication of effort; every property in a config node is parsed once for
each pin in that node. This is not such an overhead with pins and groups
properties, since having multiple pins in one config node does not occur
especially often. However, the semantics of the pinmux property make such a
configuration much more appealing. A future patch could parse all config
properties at once and store them in an array. This would make it easier to
create drivers which do not function solely as callbacks from
pinctrl-generic.
This commit increases the size of the sandbox build by approximately 48
bytes. However, it also decreases the size of the K210 device tree by 2
KiB from the previous version of this series.
The documentation has been updated from the last Linux commit before it was
split off into yaml files.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
the aspeed ddr sdram controller needs to know if the memory chip mounted on
the board is dual x8 die or not. Or it may get the wrong size of the
memory space.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
to improve the maintainability. It is more easier to modify and add
configurations of the driver in the centralized ram driver directory.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
The cfi-flash driver uses an open-coded version of the generic
algorithm to decode and translate multiple frames of a "reg" property.
This starts off the wrong foot by using the address-cells and size-cells
properties of *this* very node, and not of the parent. This somewhat
happened to work back when we were using a wrong default size of 2,
but broke about a year ago with commit 0ba41ce1b7 ("libfdt: return
correct value if #size-cells property is not present").
Instead of fixing the reinvented wheel, just use the generic function
that does all of this properly.
This fixes U-Boot on QEMU (-arm64), which was crashing due to decoding
a wrong flash base address:
DRAM: 1 GiB
Flash: "Synchronous Abort" handler, esr 0x96000044
elr: 00000000000211dc lr : 00000000000211b0 (reloc)
elr: 000000007ff5e1dc lr : 000000007ff5e1b0
x0 : 00000000000000f0 x1 : 000000007ff5e1d8
x2 : 000000007edfbc48 x3 : 0000000000000000
x4 : 0000000000000000 x5 : 00000000000000f0
x6 : 000000007edfbc2c x7 : 0000000000000000
x8 : 000000007ffd8d70 x9 : 000000000000000c
x10: 0400000000000003 x11: 0000000000000055
^^^^^^^^^^^^^^^^
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stefan Roese <sr@denx.de>
When possible use DMA for reading from CFI flash, this provides upto 5x
improvement in read performance with high speed CFI compliant flashes
like HyperFlash.
Code will gracefully fallback to CPU copy when DMA is unavailable.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Caller would need gracefully handle failures of dma_get_device(),
therefore reduce pr_err() to pr_debug() when DMA device is not found.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
- mips: octeon: add support for DWC3 USB
- mips: octeon: add support for booting Linux
-----BEGIN PGP SIGNATURE-----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=v+p3
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2020-10-07' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips
- mips: octeon: add support for DDR4 memory controller
- mips: octeon: add support for DWC3 USB
- mips: octeon: add support for booting Linux
This patch adds the glue layer for the MIPS Octeon SoCs. It's ported
mainly from the Linux code.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Octeon uses mapped addresses for virtual and physical memory. It's not
that easy to calculate the resulting addresses here. So let's remove
this BUG_ON() completely, as it's not really helpful.
Please also note, that BUG_ON() is not recommended any more in the Linux
kernel.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
On MIPS platforms, mapping of the base address is needed. This patch
switches from dev_get_addr() to dev_remap_addr() to get the mapped base
address of the xHCI controller.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
This Octeon 3 DDR driver is ported from the 2013 Cavium / Marvell U-Boot
repository. It currently supports DDR4 on Octeon 3. It can be later
extended to support also DDR3 and Octeon 2 platforms.
Part 3 includes the DIMM SPD handling code and the Kconfig / Makefile
integration.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This Octeon 3 DDR driver is ported from the 2013 Cavium / Marvell U-Boot
repository. It currently supports DDR4 on Octeon 3. It can be later
extended to support also DDR3 and Octeon 2 platforms.
Part 2 includes the very complex Octeon 3 DDR4 configuration
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This Octeon 3 DDR driver is ported from the 2013 Cavium / Marvell U-Boot
repository. It currently supports DDR4 on Octeon 3. It can be later
extended to support also DDR3 and Octeon 2 platforms.
Part 1 adds the base U-Boot RAM driver, which will be instantiated by
the DT based probing.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The cell_count argument is required when cells_name is NULL.
This patch adds this parameter in live tree API
- of_count_phandle_with_args
- ofnode_count_phandle_with_args
- dev_count_phandle_with_args
This parameter solves issue when these API is used to count
the number of element of a cell without cell name. This parameter
allow to force the size cell.
For example:
count = dev_count_phandle_with_args(dev, "array", NULL, 3);
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Add USB support for GXL and AXG SoCs
- Update Gadget code to use the new GXL and AXG USB glue driver
- Add a VIM3 board support to add dynamic PCIe enable in OS DT
- Fix AXG pinmux with requesting GPIOs
- Add missing GPIOA_18 for AXG pinctrl
- Add Amlogic PWM driver
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEPVPGJshWBf4d9CyLd9zb2sjISdEFAl97ReAACgkQd9zb2sjI
SdHHVA/9HuEAzwuJyJoyQcXARIqMwoi6w4qntlmb+VTnxxlKCzLL1Ir68W2+5Y5S
l+sVkxYDwTmYRs40FOnMdFM1r1Q7IqWwTemqQAcfmGLV+/+MwoDiludGat7JAp1i
mo/FBcBMLrf3dIJnhCyl2Rezgu06GLCQMAJOlusTDaruUZUHBxPVpAhfRvtlYq1Q
bCINZfgMcmv8EfReIOE6xGt0+9TKILqQamMByc2ZWdz5UBioqUdQ82arW1rdV/ze
ATU7vrxNmNlUQnRsMBOry9chbeuNrAhD8sqVloGPUikhf93y0BG7eINmCYrLoXjN
mopApyWzo3+50GI6It+P9vX6mWVJhd8gAJsvTkRn8ok3flGlRQPmFmAfkjngN/GH
wdkZpKi/u/ndm2Id7ekZff/Fm/ZmL/kskrRWaWrnuxHNiSNiJvAl+PU7MzCGrgED
E0MduY1hFpa7wc47xFtI0WKlcdNVQCTRwuZYVIZYlnhXeVupJyQ0dx1ggonlvvIZ
3cgS2qzd8z2RxKzhnRDvjSfwy7gWFjqpljocyRP4osoWJybJu88MIUFK2GlPdc7x
3UD/+R88FsIVsQuxzbwBuFZnP+Zo1JqCmspyX4sCeUBDNK4+MqOqIxBZry+q4qso
usWrTofg2hfxS3FgUL0pQW5GF8JGm4uXcIjbe7fMi47GJ6Lp/ec=
=rbAX
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20201005' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- generate unique mac address from SoC serial on S400 board
- Add USB support for GXL and AXG SoCs
- Update Gadget code to use the new GXL and AXG USB glue driver
- Add a VIM3 board support to add dynamic PCIe enable in OS DT
- Fix AXG pinmux with requesting GPIOs
- Add missing GPIOA_18 for AXG pinctrl
- Add Amlogic PWM driver
This adds the driver for the PWM controller found in the Amlogic SoCs.
This PWM is only a set of Gates, Dividers and Counters:
PWM output is achieved by calculating a clock that permits calculating
two periods (low and high). The counter then has to be set to switch after
N cycles for the first half period.
The hardware has no "polarity" setting. This driver reverses the period
cycles (the low length is inverted with the high length) for
PWM_POLARITY_INVERSED.
Disabling the PWM stops the output immediately (without waiting for the
current period to complete first).
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The AXG pmx driver gpio request offset needs the pin base to have the
correct pin number.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
The registers which are managed by the meson-gxl-usb3 PHY driver are
actually "USB control" registers (which are "glue" registers which
manage OTG detection and routing of the OTG capable port between the
DWC2 peripheral-only controller and the DWC3 host-only controller).
Drop the meson-gxl-usb3 PHY driver now that the dwc3-meson-gxl-usb
driver supports the USB control registers on GXL and GXM SoCs (these
were previously managed by the meson-gxl-usb3 PHY driver).
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The USB support was initialy done with a set of PHYs and dwc3-of-simple
because the architecture of the USB complex was not understood correctly
at the time (and proper documentation was missing...).
But with the G12A family, the USB complex was correctly understood and
implemented correctly.
This adds a proper driver for the glue, based on the G12A one, but with
enough changes to require a different driver in U-Boot.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl960JkcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyDaWCACYjvloDzXQaYaauWwR
whFwgkUAQ8yjadj/12We/X2b7HGisNFNE80e/V4MU8RrJDFZmohZdLWMfRKez29X
d+BG+OzVXxHWozny7ZQ2g1yYJbgCI7sVUeemQjUBZJ6aKPneQlVfwyfT2l88wOVK
yQMqS+ZyVogihR9/NHCOlJHog+6OOoBmc16w1tymM6QcO8ZsYeA66ed8SLnjDb3N
Rg2Ll2RR/lHuD/Fpxt1aUhybXFKSIOr4Qopo5X0hw5B3ibkp6JXGRE2wIwQYw6CA
q+sKTg37CSzylipkQ5EOGdLcXD7r3KIGkSbUMb8wvt6dROarnIuQ+zJeF3sr+l2H
hSoU
=vHqZ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.01-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for 2021.01 cycle:
This feature set includes a new CPU driver for at91 family, new driver
for PIT64B hardware timer, support for new at91 family SoC named sama7g5
which adds: clock support, including conversion of the clock tree to
CCF; SoC support in mach-at91, pinctrl and mmc drivers update. The
feature set also includes updates for mmc driver and some other minor
fixes and features regarding building without the old Atmel PIT and the
possibility to read a secondary MAC address from a second i2c EEPROM.
- stm32mp: convert drivers to APIs which support live DT
- stm32mp: gpio: minor fixes
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl93OLYACgkQ4rK92eCq
k3VQ3ggAlv+e3IXylevdLrCGtoPNb0mC3pB7fKcXedZ7YOHi+ag6MfLKFb3K8UCV
1h8iUX3XpGxOuOzOlqu89UFZBZXkbKP3bPnOJD8AliTEcZN/rTdZK43qYbAVM3tL
UvOtCXMzujmGwJsJqLQmXKK761fpcJFzEisajX+d6cz+at3oMF2Yoa/1RcC8Z7fi
DHWaUME132H5A9pzmt84N83neJNgMmFIDyHBWjNSMkvdiE5jz8MAPFrua8FDyymS
w0QmKmN0ub+5kJqXu4X/LCMZUjYozC3lfNbnwRIkXXKJtQuGEea963bBi7Gastdb
gSCQKmrwjtxa4/g/bpalDTMAvirKnQ==
=Q/62
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20201003' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm into next
- stm32mp: DT alignment with Linux 5.9-rc4
- stm32mp: convert drivers to APIs which support live DT
- stm32mp: gpio: minor fixes
Currently, the return value of dev_read_u32_default is stored in an u32,
causing the subsequent "if (function < 0)" to always be false:
u32 function;
...
function = dev_read_u32_default(config, "brcm,function", -1);
if (function < 0) {
debug("Failed reading function for pinconfig %s (%d)\n",
config->name, function);
return -EINVAL;
}
Make "function" variable an int to fix this.
Cc: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Factor out reading IP base address to ofdata_to_platdata function, which
is designed for this purpose. Also, drop the dev->priv NULL check, since
this is already done by the dm core when allocating space using
priv_auto_alloc_size feature. (in drivers/core/device.c ->
device_ofdata_to_platdata).
Cc: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the
driver can support live DT.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the
driver can support live DT.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Yannick Fertré <yannick.fertre@st.com>
Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the
driver can support live DT.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Yannick Fertré <yannick.fertre@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the
driver can support live DT.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add test on the size of ofnode_phandle_args result to avoid access
to uninitialized elements in args[] field.
This patch avoids the issue when gpio-ranges cell size is not 3 as
expected, for example:
gpio-ranges = <&pinctrl 0>;
instead of
gpio-ranges = <&pinctrl 0 112 16>;
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move the variables definition at the beggining of the function
gpio_stm32_probe().
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Upon further discussion on the mailing list, we should not get in the
situation where the generic code path to set ethaddr/etc correctly does
not work. Revert this until someone can further debug the smc911x
driver regarding this issue.
This reverts commit 387cbf096e.
Signed-off-by: Tom Rini <trini@konsulko.com>
The R8A774A1 is compatible with the generic rcar-gen3-xhci controller.
This patch adds the compatibility flag, to support the xHCI controller.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Use readx_poll_sleep_timeout() to poll the register status
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use macros with parameter to fill ep_info2, then some macros
for MASK and SHIFT can be removed
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use TRB_TX_TYPE() instead of (TRB_DATA_OUT/IN << TRB_TX_TYPE_SHIFT)
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
For normal TRB fields:
use TRB_LEN(x) instead of ((x) & TRB_LEN_MASK);
and use TRB_INTR_TARGET(x) instead of
(((x) & TRB_INTR_TARGET_MASK) << TRB_INTR_TARGET_SHIFT)
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
There some vendor quirks for MTK xHCI 0.96 host controller:
1. It defines some extra SW scheduling parameters for HW
to minimize the scheduling effort for synchronous and
interrupt endpoints. The parameters are put into reserved
DWs of slot context and endpoint context.
2. Its TDS in Normal TRB defines a number of packets that
remains to be transferred for a TD after processing all
Max packets in all previous TRBs.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
xhci versions 1.0 and later report the untransferred data remaining in a
TD a bit differently than older hosts.
We used to have separate functions for these, and needed to check host
version before calling the right function.
Now Mediatek host has an additional quirk on how it uses the TD Size
field for remaining data. To prevent yet another function for calculating
remainder we instead want to make one quirk friendly unified function.
Porting from the Linux:
c840d6ce772d("xhci: create one unified function to calculate TRB TD remainder.")
124c39371114("xhci: use boolean to indicate last trb in td remainder calculation")
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a member to save xHCI version, it's used some times.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
commit 7c8f821e5d ("i2c: rcar_i2c: Set the slave address from
rcar_i2c_xfer") blindly called rcar_i2c_set_addr() with read argument
always set to 1 during xfer which introduced read/write errors, whereas
earlier rcar_i2c_read_common() called rcar_i2c_set_addr() with read set to
1 and rcar_i2c_write_common() called rcar_i2c_set_addr() with read set 0.
Fixes: 7c8f821e5d ("i2c: rcar_i2c: Set the slave address from rcar_i2c_xfer")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the
driver can support live DT.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support for stingray PAXB PHY controller driver.
This driver supports maximum 8 PAXB phys using pipemux data.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The ethernet controller can read the MAC from EEPROM and display it,
but if ethaddr is not set, the ethernet is still unavailable.
This patch checks will automatically set the MAC address if it has
not already been set.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
ftgmac100 driver is using hard-coded PHY interface address of zero.
Each board can have different PHY interface address (phy_addr).
This commit modifies the driver to make use of board specific address
by leveraging CONFIG_PHY_ADDR.
Signed-off-by: Thirupathaiah Annapureddy <thiruan@linux.microsoft.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
The Linux kernel does set the clock delays to
- 0.2 ns (their default, and lowest, hardware value) if delays should
not be enabled
- 2.0 ns (which causes the data to be sampled at exactly half way between
clock transitions at 1000 Mbps) if delays should be enabled
depending on the interface mode
See https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/net/phy/mscc/mscc_main.c#n523
So instead of using arbitrary delay values like now, mimic this behaviour.
The behaviour is the same for all of vsc8530/8531/8540/8541 so move that
to a shared function while at it.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The vsc8530/8531/8540/8541 phys have a configurable clock output that
can emit 25, 50 and 125 MHz rates, which in turn may be needed for
stable network connections.
This follows a similar change introduced into the Linux kernel at
https://lore.kernel.org/netdev/20200609133140.1421109-2-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add tests for SCMI reset controllers. A test device driver
sandbox-scmi_devices.c is used to get reset resources, allowing further
resets manipulation.
Change sandbox-smci_agent to emulate 1 reset controller exposed through
an agent. Add DM test scmi_resets to test this reset controller.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This change introduces a reset controller driver for SCMI agent devices.
When SCMI agent and SCMI reset domain drivers are enabled, SCMI agent
binds a reset controller device for each SCMI reset domain protocol
devices enabled in the FDT.
SCMI reset driver is embedded upon CONFIG_RESET_SCMI=y. If enabled,
CONFIG_SCMI_AGENT is also enabled.
SCMI Reset Domain protocol is defined in the SCMI specification [1].
Links: [1] https://developer.arm.com/architectures/system-architectures/software-standards/scmi
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add tests for SCMI clocks. A test device driver sandbox-scmi_devices.c
is used to get clock resources, allowing further clock manipulation.
Change sandbox-smci_agent to emulate 3 clocks exposed through 2 agents.
Add DM test scmi_clocks to test these 3 clocks.
Update DM test sandbox_scmi_agent with load/remove test sequences
factorized by {load|remove}_sandbox_scmi_test_devices() helper functions.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This change introduces a clock driver for SCMI agent devices. When
SCMI agent and SCMI clock drivers are enabled, SCMI agent binds a
clock device for each SCMI clock protocol devices enabled in the FDT.
SCMI clock driver is embedded upon CONFIG_CLK_SCMI=y. If enabled,
CONFIG_SCMI_AGENT is also enabled.
SCMI Clock protocol is defined in the SCMI specification [1].
Links: [1] https://developer.arm.com/architectures/system-architectures/software-standards/scmi
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This change implements a SMCCC transport for SCMI exchanges. This
implementation follows the Linux kernel as references implementation
for SCMI message processing, using the SMT format for communication
channel meta-data.
Use of SMCCC transport in SCMI FDT bindings are defined in the Linux
kernel DT bindings since v5.8. SMCCC with SMT is implemented in OP-TEE
from tag 3.9.0 [2].
Links: [2] https://github.com/OP-TEE/optee_os/commit/a58c4d706d23
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This change implements a mailbox transport using SMT format for SCMI
exchanges. This implementation follows the Linux kernel and
SCP-firmware [1] as references implementation for SCMI message
processing using SMT format for communication channel meta-data.
Use of mailboxes in SCMI FDT bindings are defined in the Linux kernel
DT bindings since v4.17.
Links: [1] https://github.com/ARM-software/SCP-firmware
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This change introduces SCMI agent uclass to interact with a firmware
using the SCMI protocols [1].
SCMI agent uclass currently supports a single method to request
processing of the SCMI message by an identified server. A SCMI message
is made of a byte payload associated to a protocol ID and a message ID,
all defined by the SCMI specification [1]. On return from process_msg()
method, the caller gets the service response.
SCMI agent uclass defines a post bind generic sequence for all devices.
The sequence binds all the SCMI protocols listed in the FDT for that
SCMI agent device. Currently none, but later change will introduce
protocols.
This change implements a simple sandbox device for the SCMI agent uclass.
The sandbox nicely answers SCMI_NOT_SUPPORTED to SCMI messages.
To prepare for further test support, the sandbox exposes a architecture
function for test application to read the sandbox emulated devices state.
Currently supports 2 SCMI agents, identified by an ID in the FDT device
name. The simplistic DM test does nothing yet.
SCMI agent uclass is designed for platforms that embed a SCMI server in
a firmware hosted somewhere, for example in a companion co-processor or
in the secure world of the executing processor. SCMI protocols allow an
SCMI agent to discover and access external resources as clock, reset
controllers and more. SCMI agent and server communicate following the
SCMI specification [1]. This SCMI agent implementation complies with
the DT bindings defined in the Linux kernel source tree regarding
SCMI agent description since v5.8.
Links: [1] https://developer.arm.com/architectures/system-architectures/software-standards/scmi
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A regmap field is an abstraction available in Linux. It provides to access
bitfields in a regmap without having to worry about shifts and masks.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Some devices need to calculate the regmap base address at runtime. This
makes it impossible to use device tree to get the regmap base. Instead,
allow devices to specify it in the regmap config. This will create a
regmap with a single range that corresponds to the start and size given
by the driver.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Right now, the base of a regmap can only be obtained from the device
tree. This makes it impossible for devices which calculate the base at
runtime to use a regmap. An example of such a device is the Cadence
Sierra PHY.
Allow creating a regmap with one range whose start and size can be
specified by the driver based on calculations at runtime.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Drivers can configure it to adjust the final read/write location.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Right now, regmap_read() and regmap_write() read/write a 32-bit value
only. To write other lengths, regmap_raw_read() and regmap_raw_write()
need to be used.
This means that any driver ported from Linux that relies on
regmap_{read,write}() to know the size already has to be updated at each
callsite. This makes the port harder to maintain.
So, allow specifying the read/write width to make it easier to port the
drivers, since now the only change needed is when initializing the
regmap.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some fields will be introduced in the regmap structure that should be
set to 0 by default. So, once we allocate a regmap, make sure it is
zeroed out to avoid unexpected defaults for those values.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Most of new linux drivers are using managed-API to allocate resources. To
ease porting drivers from linux to U-Boot, introduce devm_regmap_init() as
a managed API to get a regmap from the device tree.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Add managed functions to get a gpio from the devce-tree, based on a
property name (minus the '-gpios' suffix) and optionally an index.
When the device is unbound, the GPIO is automatically released and the
data structure is freed.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
The tests are basically the same as for the regular API. Except that
the reset are initialized using the managed API, and no freed manually.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Add managed functions to get a reset_ctl from the device-tree, based on a
name or an index.
Also add a managed functions to get a reset_ctl_bulk (array of reset_ctl)
from the device-tree.
When the device is unbound, the reset controllers are automatically
released and the data structure is freed.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
- Disable CMD_IRQ for RISC-V.
- Update sipeed/maix doc
- Obtain reg of SiFive RAM via dev_read_addr_index() instead of regmap API.
- Cleans up RISC-V timer drivers and converts them to DM.
- Correctly handle IPIs already pending upon prior stage bootloader (on the K210)
There is no member `dev` in dw_mipi_dsi, but there is one in mipi_dsi_host,
so use that.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This driver does not use DM, so we need to use a struct device instead of a
struct udevice. Not ideal, but it'll have to do for now.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This can conflict with asm/io.h on some archs, and it isn't needed to build
dwc3-generic.c
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This driver does not use DM, so use log_xxx instead.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This logs with the device from struct dwc3. Some files also need to include
dm.h so fields in udevice can be accessed.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This adds a dev argument to some functions so dev_xxx always has a device
to log with. In one instance we must use use a different log function when
we are compiled without DM_USB.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
ep0.c also need to include dm.h so dev_xxx can access udevice fields.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Use `bus` instead of `dev`.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Remove the indirection.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Usually we can get a device from the current core, but some dev_dbg calls
have been converted to debug, since we are called on a cluster.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This function is never used anywhere, and it also tries to log with a
nonexistant device.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Use the phy's device.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
`phy` doesn't exist; we need to use `x` instead.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Get the device from phy, or pass the phy in.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Without DM_ETH, cpsw_priv.dev is an eth_device. Just use its name instead.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Pass a udevice into a few functions so `dev` is defined.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
There's no dev to log with, so pass the device along with the priv data.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
netdev_xxx evaluates to printf in U-Boot, so there is no extra info
printed. mvpp2 one of only two drivers which use these functions in U-Boot.
Convert these functions to dev_xxx where possible (and to log_xxx where
not).
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Remove some prefixes, or get the device from the phy.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
netdev_xxx evaluates to printf in U-Boot, so there is no extra info
printed. mvneta is one of two drivers which use these functions in U-Boot.
Convert these functions to dev_xxx where possible (and to log_xxx where
not).
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
No need for indirection here.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This member was presumably dropped when this driver was converted from
Linux. However, it is still used in log statements during initialization.
This patch adds the member back. In addition, allocation of struct
vf610_nfc has been moved to the callers of vf610_nfc_nand_init. This allows
it to be allocated by DM (if it is being used) and for dev to be
initialized.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
There are too many levels of indirection when calling dev_err. This is an
artifact of the conversion of brcmnand_host.pdev from a struct
platform_device (which has a member `dev` pointing to a struct device) to
struct udevice.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Use mtd_info to get a device to log with.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
dev needs to be gotten from mbox_chan
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This adds a udevice parameter to get_best_delay and msdc_set_mclk so they
can call dev_err properly.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Get it from spinand->slave->dev. Another option would be to use
spinand_to_mtd(spinand)->dev, but this is what the existing code uses.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This fixes dev_xxx() not always being called with a device. In
spi_nor_reg_read, a the slave device may not always be available, so we use
bus and cs instead.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This header is needed so struct udevice can be used in dev_xxx().
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Usually the device is gotten from sunxi_nfc. This is a struct device and
not a struct udevice, but the whole driver seems to be written wihout DM
anyway...
In a few instances, this patch modifies functions to take an nfc to log
with. In once instance we use mtd_info's device since there is no nfc.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Use the device from any mtd already available, or from the active mtd via
pxa3xx_nand_info if one is not.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
The udevice we are working with is called `bus` and not `dev`.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This converts calls to dev_err to get the device from ti_sci_info where
appropriate.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
We can't use dev_dbg here because we haven't bound to the device yet. Use
log_debug instead.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Another "virtual" clock (in the sense that it isn't configurable). This
could possibly be done as a clock in the device tree, but I think this is a
bit cleaner.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
To test this function, sandbox CPU must set cpu_platdata.timebase_freq on
bind. It also needs to expose a method to set the current cpu. I also make
some most members of cpu_sandbox_ops static.
On the timer side, the device tree property
sandbox,timebase-frequency-fallback controls whether sandbox_timer_probe
falls back to time_timebase_fallback or to SANDBOX_TIMER_RATE.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This function is designed to be used when a timer used to be initialized by
the cpu (e.g. RISC-V timers), but now is initialized by dm_timer_init. In
such a case, the timer may prefer to use the clocks and clock-frequency
properties, but should be able to fall back on using the cpu's
timebase-frequency.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The riscv-timer driver currently serves as a shim for several riscv timer
drivers. This is not too desirable because it bypasses the usual timer
selection via the driver model. There is no easy way to specify an
alternate timing driver, or have the tick rate depend on the cpu's
configured frequency. The timer drivers also do not have device structs,
and so have to rely on storing parameters in gd_t. Lastly, there is no
initialization call, so driver init is done in the same function which
reads the time. This can result in confusing error messages. To a user, it
looks like the driver failed when trying to read the time, whereas it may
have failed while initializing.
This patch removes the shim functionality from the riscv-timer driver, and
has it instead implement the former rdtime.c timer driver. This is because
existing u-boot users who pass in a device tree (e.g. qemu) do not create a
timer device for S-mode u-boot. The existing behavior of creating the
riscv-timer device in the riscv cpu driver must be kept. The actual reading
of the CSRs has been redone in the style of Linux's get_cycles64.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The usage of regmap API in the SiFive RAM driver is not correct.
The reg address should be obtained via dev_read_addr_index() API.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Fix a typo
%s/interract/interact/
Use Samsung's capitalization of their trademarks
%s/onenand/OneNAND/
%s/Hyperflash/HyperFlash/
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
[trini: Add other Hyperflash cases as noted by Stefan]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support for Microchip PIT64B timer. The timer is 64 bit length and
is used as a free running counter (in continuous mode with highest values
for period registers). The clock feeding the timer would be no more
than 12.5MHz.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
This fixes HWRNG support on Amlogic GXL, GXM, G12A, G12B & SM1
based boards dues to the lack of the core clock in the device tree.
It was reported breaking EFI boot in the Linux EFI stub, because the
EFI_RNG_PROTOCOL didn't check for the RNG device presence before
installing itself.
The Linux amlogic,meson-rng.yaml doesn't mandate the core clock,
this the clock should be ignores if not present.
Nevertheless, the clock should be present and this should be fixed
on the Linux meson-gxl.dtsi & meson-g12-common.dtsi then synced
with U-Boot.
The change has been tested on a Khadas VIM3, which uses the common
meson-g12-common.dtsi like the Odroid-C4 & Odroid-N2 in Scott's
report, along with the RNG cmd.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reported-by: Scott K Logan <logans@cottsay.net>
Fixes: bc40eb278b ("drivers/rng: add Amlogic hardware RNG driver")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Scott K Logan <logans@cottsay.net>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The micrel phy driver is already configuring this values from
device tree. So remove the redundant phy configuration call from
this driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
R8A774A1 is part of Renesas RZ/G2 series and not R-Car, reflect the same
for PINCTRL_PFC_R8A774A1 help description
Alongside, sort the PINCTRL_PFC_R8A774A1 config option as per increasing
number of the SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
- Enhance the 'zboot' command to be more like 'bootm' with sub-commands
- The last series of ACPI core changes for programmatic generation of
ACPI tables
- Add all required ACPI tables for ApolloLake and enable ACPIGEN on
Chromebook Coral
- A feature minor enhancements to the 'hob' command
- Intel edison: Support for writing an xFSTK image via binman
Call mmc_of_parse at probe time to fetch all the host properties
from the DT.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The second clock of the IP block (the generic clock), must be explicitly
enabled.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Peng Fan <pengfan@nxp.com>
clk_set_rate will return rate in case of success and zero in case of
error, however it can also return -ev, but it's an ulong function.
To avoid any issues, disregard the return value of this call.
In case this call actually fails, nothing much we can do anyway, but we
can at least try with the previous values (or DT assigned-clocks)
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add new compatibility string for matching sama7g5 product.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Many I2C devices produce roughly the same ACPI data with just things like
the GPIO/interrupt information being different.
This can be handled by a generic driver along with some information in the
device tree.
Add a generic i2c driver for this purpose.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
LX2160A rev2 uses different PCIe controller, so EP mode DT
nodes also need to be fixed up.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
CONFIG_DM_SPI_FLASH is only supported now with passing of driver
conversion deadline from non-DM to DM model. Hence, it's safe to remove
non-DM code check from pfe_spi_flash_init.
Also use CONFIG_ENV_SPI_MODE and CONFIG_ENV_SPI_MAX_HZ instead of
reading reading values from DT.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Fix Coverity issue: RESOURCE_LEAK.
leaked_storage: Variable addr going out of scope leaks the storage it
points to.
Fixes: e0152dbed6 ("net: pfe_eth: Use spi_flash_read API to access
flash memory")
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
All the 10G ports that were working in XFI mode were described as
using XGMII (as PHY_INTERFACE_MODE_XFI was not added at the time).
Add the minimal changes required for the FMan code to support XFI.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
PFE DDR addresses are now stored on to a stack varaiable rather
dynamic allocation.
Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
correction in delay implementation before we exit out of tx timeout.
Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The next DPMAC was always verified if it is enabled. In case of
DPMAC@6, the DPMAC@7 is verified. As DPMAC@7 is disabled, DPMAC@6 will
be considered disabled and not detected by uboot.
Signed-off-by: Grigore Popescu <grigore.popescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX2x4MgAKCRDKSWXLKUoM
IZQtAJ9HpNwG5q3nHt9WedzLCTkr3YoLAACeJJ0Wlpp5p5xPzuPmnoo/Vi4MtNQ=
=yxRo
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.01
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
The info of fixed-link PHY is described in DT node instead of
getting from MII, so detect the fixed-link PHY DT node first,
if it doesn't exist then probe the MII.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
For the platforms on which the eTSEC driver uses DM_ETH, convert its
MDIO controller code to also use DM_MDIO.
Note that for handling the TBI PHY (the MAC PCS for SGMII), we still
don't register a udevice for it, since we can drive it locally and there
is no point in doing otherwise.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Reworked to fix gazerbeam config]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The MII management register block offset is different between
gianfar and etsec2 compatible devices, this patch is to fix
this issue by adding driver data for different compatible
string.
Fixes: 2932c5a802 ("net: tsec: fsl_mdio: add DM MDIO support")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Use virtual address to access the MII block registers instead
of physical address.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
It is utterly pointless to require an MDIO bus pointer for a fixed PHY
device. The fixed.c implementation does not require it, only
phy_device_create. Fix that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
As required by PCI Express spec a delay for at least 100ms after
de-asserting PERST# signal is needed before link training is enabled.
Linux kernels prior to 5.8 version do not automatically disable link
training before de-asserting PERST# signal, therefore this requirement is
not fulfilled.
Above requirement is needed for proper detection of some Compex PCIe WiFi
cards. Otherwise Linux kernel cannot detect it.
To allow using those PCIe cards with older Linux kernel versions booted by
U-Boot compiled with U-Boot a37xx pci driver, disable link training in
U-Boot when unloading this pci driver.
Thanks to DM_FLAG_OS_PREPARE flag, U-Boot automatically unload this driver
when booting Linux kernel.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Some of Marvell A3700 boards use mx25u12835f, specifically uDPU
and ESPRESSObin v7.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
[a.heider: adapt commit message to mainline]
Signed-off-by: Andre Heider <a.heider@gmail.com>
The fdt_fixup_pcie_ls() scans all PCI devices and assumes that all PCI
root devices are layerscape PCIe controllers. Unfortunately, this is not
true for the LS1028A. There is one additional static PCI root complex
(this contains the networking devices) which has nothing to do with the
layerscape PCIe controllers. On recent U-Boot versions this results in
the following panic:
"Synchronous Abort" handler, esr 0x96000044
elr: 000000009602fa04 lr : 000000009602f9f4 (reloc)
elr: 00000000fbd73a04 lr : 00000000fbd739f4
x0 : 0080000002000101 x1 : 0000000000000000
x2 : 00000000fbde9000 x3 : 0000000000000001
x4 : 0000000000000000 x5 : 0000000000000030
x6 : 00000000fbdbd460 x7 : 00000000fbb3d3a0
x8 : 0000000000000002 x9 : 000000000000000c
x10: 00000000ffffffe8 x11: 0000000000000006
x12: 000000000001869f x13: 0000000000000a2c
x14: 00000000fbb3d2cc x15: 00000000ffffffff
x16: 0000000000010000 x17: 0000000000000000
x18: 00000000fbb3fda0 x19: 0000000000000800
x20: 0000000000000000 x21: 00000001f0000000
x22: 0000000000000800 x23: 0000000000000009
x24: 00000000fbdc3c1b x25: 00000000fbdc28e5
x26: 00000000fbdcc008 x27: 00000000fbdc16e2
x28: 000000000f000000 x29: 00000000fbb3d3a0
Code: 394072a1 f94006a0 34000041 5ac00a94 (b8336814)
Resetting CPU ...
This bug already existed in former versions, but the spurious write was
never trapped, because the destination address was a valid address (by
pure luck).
Make sure the PCI root is actually one of the expected PCIe layerscape
controllers by matching its compatible string.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
fixed-rate driver is not different from clk_fixed_factor and it is required
very early in boot that's why setup flag for it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
if conditions should match.
Fixes: a18d09ea38 ("fpga: zynqmp: Add secure bitstream loading for ZynqMP")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch does sed 's/SPL_FPGA_SUPPORT/SPL_FPGA/g' but also fixing Makefile
and zynqmp.c to simplify if/endif logic in zynqmp.c.
This change is mostly done to be able to use CONFIG_IS_ENABLED macro and
obj-$(CONFIG_$(SPL_)FPGA) in Makefile. For them symbols need to be in sync.
And removing one line from Topic Miami boards which is not needed because
symbol is not enabled via Kconfig.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
flush_cache() arguments are not type casted to take care of 64 bit
systems. Use phys_addr_t to type cast for it to work properly for 32 bit
and 64 bit systems.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
There are compilation warnings showing up when we compile AXI ethernet
driver for 64bit architectures. Fix them, so that it works on both 32
and 64 bit architectures.
DMA descriptors are not taking care of 64bit addresses. To fix it,
change axidma_bd members as below:
next ==> next_desc
reserverd1 ==> next_desc_msb
phys ==> buf_addr
reserverd2 ==> buf_addr_msb
and update next_desc and buf_addr with lower 32 bits of the addresses,
update next_desc_msb and buf_addr_msb with upper 32 bits of the 64bit
addresses.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
NAND_ARASAN selecting DM_MTD uunconditionally. Driver can be enabled with
!DM that's why Kconfig it showing it as error:
WARNING: unmet direct dependencies detected for DM_MTD
Depends on [n]: DM [=n]
Selected by [y]:
- NAND_ARASAN [=y] && MTD_RAW_NAND [=y]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This endinness changes are taken from linux uartlite driver.
Reset TX fifo in control register and check TX fifo empty
flag in lower byte of the status register to detect if it
is a little endian system. Based on this check, program the
registers with le32 or be32 through out the driver.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Zynq/ZynqMP/Versal IPs should be possible to called also from Microblaze in
PL and vice versa. That's why change dependencies and do not limit enabling
just for some platforms.
This is follow up patch based on commit 664e16ce99 ("xilinx: kconfig:
Change Kconfig dependencies for Xilinx drivers").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Find out MDIO bus and enable MDIO access to it if this is done via
different GEM controller. Only works across GEM instances.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The most of drivers are using '_' instead of '-' in driver name. That's why
sync up these names to be aligned. It looks quite bad to see both in use.
It is visible via dm tree command.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The GPIO pins used by the SDHCI controller need to be configured to
allow the interface to work.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
The existing driver is not compatible with the Driver Model.
This patch makes the necessary changes while also removing obsolescent
calls/properties as follows:
- fdtdec_* calls replaced with dev_read_* equivalents;
- 'clock-freq-min-max' property replaced by querying the frequency of
the source clock 'base_clk';
- The card detect erratum workaround is applied during probe rather than
overriding get_cd.
The card detect workaround (Microchip ref. DS80000736E, erratum #15) is
not always needed and can be disabled using a vendor specific DT
property.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
In the live tree API ofnode_parse_phandle_with_args, the cell_count
argument must be used when cells_name is NULL.
But this argument is not provided to the live DT function
of_parse_phandle_with_args even it is provided to
fdtdec_parse_phandle_with_args.
This patch adds support of the cells_count parameter in dev_ and
of_node API to allow migration and support of live DT:
- of_parse_phandle_with_args
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix build failure, it used to get this implicitly through common.h
until f7ae49fc4f (common: Drop log.h from common header).
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Heiko Schocher <hs@denx.de>
Somewhere between v2020.04 and v2020.07 the mpc8xxx_spi driver broke,
I'm guessing due to this hunk
@@ -559,6 +560,8 @@ int dm_gpio_set_dir_flags(struct gpio_desc *desc, ulong flags)
if (ret)
return ret;
+ /* combine the requested flags (for IN/OUT) and the descriptor flags */
+ flags |= desc->flags;
ret = _dm_gpio_set_dir_flags(desc, flags);
from commit 695e5fd546 ("gpio: update dir_flags management"). But
the blame is mostly on the driver itself which seems rather confused:
The chip select gpios are requested with GPIOD_ACTIVE_LOW, but then in
each activate/deactivate, dm_gpio_set_dir_flags() is called with
merely GPIOD_IS_OUT, and then the driver call set_value(0) for
activate.
That used to work, but with the above hunk, the ACTIVE_LOW setting
from the request becomes persistent, so the gpio driver ends up being
asked to set the value to 1 in mpc8xxx_spi_cs_activate().
So drop the dm_gpio_set_dir_flags() calls in the activate/deactivate
functions, and use a value of 1 to mean "logically enabled".
Ideally, I think we should also drop the GPIOD_ACTIVE_LOW from the
request and make it up to the list of gpio cs in DT to indicate
whether that CS is enabled when driven low (as is of course usually
the case), but that requires changing
arch/powerpc/dts/gdsys/gazerbeam-base.dtsi among others, and I don't
have that hardware to test on. I have, however, tested our
own (mpc8309-based) hardware with this change, and I have also tested
that removing the GPIOD_ACTIVE_LOW from the request and updating our
DT as
- gpios = <&spisel 0 0>;
+ gpios = <&spisel 0 GPIO_ACTIVE_LOW>;
still works.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Add UTMI support for SAMA7G5. SAMA7G5's UTMI control is done via
XTALF register. Values written at bits 2..0 in this register
correspond to the on board crystal oscillator frequency.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Add master clock (MCK1..MCK4) support for SAMA7G5. SAMA7G5's PMC has
multiple master clocks feeding different subsystems. One of them
feeds image subsystem and is changeable based on image subsystem
needs.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Add sckc driver compatible with common clock framework. Driver
implements slow clock support for SAM9X60 compatible IPs (in this
list it is also present SAMA7G5's slow clock IP).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Move clock code to compat.c to allow switching to CCF
without mixing CCF code with non CCF code. This prepares the
field for next commits.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Add helper for clock drivers. These will be used by following
commits in the process of switching AT91 clock drivers to CCF.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
clk_get_by_indexed_prop() retrieves a clock with dev member being set
with the pointer to the udevice for the clock controller driver. But
in case of CCF each clock driver has set in dev member the reference
to its parent (the root of the clock tree is a fixed clock, every
node in clock tree is a clock registered with clk_register()). In this
case the subsequent operations like dev_get_clk_ptr() on clocks
retrieved by clk_get_by_indexed_prop() will fail. For this, get the
pointer to the proper clock registered (with clk_register()) using
clk_get_by_id() before proceeding.
Fixes: 1d7993d1d0 ("clk: Port Linux common clock framework [CCF] for imx6q to U-boot (tag: v5.1.12)")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Clock re-parenting is not binding the clock's device to its new
parent device, it only calls the clock's ops->set_parent() API. The
changes in this commit re-parent the clock device to its new parent
so that subsequent operations like clk_get_parent() to point to the
proper parent.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In common clock framework the relation b/w parent and child clocks is
determined based on the udevice parent/child information. A clock
parent could be changed based on devices needs. In case this is happen
the functionalities for clock who's parent is changed are broken. Add
a function that reparent a device. This will be used in clk-uclass.c
to reparent a clock device.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The following bugs are fixed:
* incorrect online help for setenv and env
* description of function efi_mem_carve_out()
* replace printf() by log_err() in stm32mp1_rng driver
A unit test is provided to check that the boot hart id is provided in the
RISC-V device-tree.
-----BEGIN PGP SIGNATURE-----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=vhkz
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-10-rc5-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-10-rc5 (2)
The following bugs are fixed:
* incorrect online help for setenv and env
* description of function efi_mem_carve_out()
* replace printf() by log_err() in stm32mp1_rng driver
A unit test is provided to check that the boot hart id is provided in the
RISC-V device-tree.
The logging system provides flexible filtering and enhanced output.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Lot of Qualcomm SoC-s use DWC3 controller for both USB2.0 and USB3.0
ports.
Qualcomm has some custom config registers on top of the generic ones,
but for host mode these are not needed.
So lets add the neccessary compatible string.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Add a driver to setup the USB PHY-s on Qualcomm IPQ40xx series SoCs.
The driver sets up HS and SS phys.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
On Qualcomm IPQ40xx SoC series, GCC clock IP also handles the resets.
So since this will be needed by further drivers, lets add a driver for the reset controller.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
There is already existing driver for SMEM so lets enable it for IPQ40xx as well.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Currently, after config the clock rate, delay 10ms, this is quite a rough
method. Check the clock stable status in the present status register is
enough.
Tested-by: Ji Luo <ji.luo@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
add DM/DTS support for the UEC ethernet on QUICC Engine
Block.
Signed-off-by: Heiko Schocher <hs@denx.de>
Patch-cc: Mario Six <mario.six@gdsys.cc>
Patch-cc: Qiang Zhao <qiang.zhao@nxp.com>
Patch-cc: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Patch-cc: Madalin Bucur <madalin.bucur@oss.nxp.com>
Series-changes: 3
- revert:
commit "3374264df97b" ("drivers: net: qe: deselect QE when DM_ETH is enabled")
as now qe works with DM and DM_ETH support.
- fix mailaddress from Holger
Series-changes: 2
- add comments from Qiang Zhao:
- add device node documentation
- I did not drop the dm_qe_uec_phy.c and use drivers/net/fsl_mdio.c
because using drivers/net/fsl_mdio.c leads in none existent
udevice mdio@3320
instead boards with DM ETH support should use now this
driver.
- remove RFC tag
Commit-notes:
- I let the old none DM based implementation in code
so boards should work with old implementation.
This Code should be removed if all boards are converted
to DM/DTS.
- add the DM based qe uec driver under drivers/net/qe
- Therefore copied the files uccf.c uccf.h uec.h from
drivers/qe. So there are a lot of Codingstyle problems
currently. I fix them in next version if this RFC
patch is OK or it needs some changes.
- The dm based driver code is now under drivers/net/qe/dm_qe_uec.c
Used a lot of functions from drivers/qe/uec.c
- seperated the PHY specific code into seperate file
drivers/net/qe/dm_qe_uec_phy.c
END
add DM support for parallel I/O ports on QUICC Engine Block
Signed-off-by: Heiko Schocher <hs@denx.de>
Patch-cc: Mario Six <mario.six@gdsys.cc>
Patch-cc: Qiang Zhao <qiang.zhao@nxp.com>
Patch-cc: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Series-changes: 2
- remove RFC
- fixed Codingstyle errors, therefore new patch
powerpc, mpc83xx: fix codingstyle issues for qe_io.c
- moved DM part to drivers/pinctrl
Commit-notes:
Open questions / discussion:
- I let the old none DM based implementation in code
so boards should work with old implementation.
This should be removed if all boards are converted to
DM/DTS.
- Unfortunately linux DTS does not use "pinctrl-"
properties, instead "pio-handle" properties.
Even worser old U-Boot code initializes all pins
defined in "const qe_iop_conf_t qe_iop_conf_tab[]"
table in board code. As linux does the same I decided
to also scan through all subnodes containing "pio-map"
property and initialize them too.
The proper solution would be to check for "pio-handle"
when a device is probed.
END
- Hyperflash boot for J7200
- Update Main R5FSS lockstep mode
- R5F remoteproc support for J7200
- Minor env fixes
- Add SPI boot support for am335x-icev2
Add an ofdata_to_platdata() callback to access dts in U-boot and
access all platform data in it. This prepares the driver for supporting
both device tree as well as static platform data structures in SPL.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Add platform data and a device structure for the spi device
present on am335x-icev2. This requires moving all omap3_spi
platform data structures and symbols to an omap3_spi.h so that
the board file can access them.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
There are devices which don't use OF_CONTROL or OF_PLATDATA but instead
rely on statically defined platdata. Block dm_scan_fdt_dev() with both
configs to avoid build failures under this condition.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The K3 J7200 SoC family has a revised R5F sub-system and contains a
subset of the R5F clusters present on J721E SoCs. The integration of
these clusters is very much similar to J721E SoCs otherwise.
The revised IP has the following two new features:
1. TCMs are auto-initialized during module power-up, and the behavior
is programmable through a MMR bit controlled by System Firmware.
2. The LockStep-mode allows the Core1 TCMs to be combined with the
Core0 TCMs effectively doubling the amount of TCMs available.
The LockStep-mode on previous SoCs could only use the Core0 TCMs.
This combined TCMs appear contiguous at the respective Core0 TCM
addresses.
Add the support to these clusters in the K3 R5F remoteproc driver
using J7200 specific compatibles and revised logic accounting for
the above IP features/differences.
Signed-off-by: Suman Anna <s-anna@ti.com>
Use mmc_of_parse() to set the common host properties. That includes
"bus-width", so parsing it can be removed from the driver.
But more importantly, "non-removable" is now respected, which fixes
the usage of eMMC.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Tested-by: Marek Behún <marek.behun@nic.cz>
Since the introduction of 'get_cd' callback in sdhci core,
dragonboard410c's MMC interface is broken. It turns out that 'get_cd'
callback checks for the host_caps for validating the chip select. And
since the msm_sdhci driver is not parsing the host_caps from DT, not
all of the cababilities are parsed properly. This results in the MMC
interfaces to be broken.
Hence, fix this by adding a call to 'mmc_of_parse' during driver probe.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Aníbal Limón <anibal.limon@linaro.org>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Nand writes should skip the bad blocks with "nand write" command.
In case of bad blocks with above 32-bit address, nand_block_isbad()
returns false due to truncated bad block address.
In below code segment,
if (nand_block_isbad(mtd, offset & ~(mtd->erasesize - 1)))
offset is 64-bit and mtd->erasesize is 32-bit, hence the truncation is
happening. Cast 'mtd->erasesize' with loff_t to fix this issue.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
On the mt7623 platform, if one port enable fail and other port
enable succeed. It will hang on when using pci enum
because the resource was not released correctly.
Signed-off-by: Chuanjia Liu <Chuanjia.Liu@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
On the mt7623 platform, if one port enable fail and other port
enable succeed. It will hang on when using pci enum
because the resource was not released correctly.
Signed-off-by: Chuanjia Liu <Chuanjia.Liu@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
v2: modify title description aspeed:clock -> clock:aspeed
Use kernel include/dt-bindings/clock/aspeed-clock.h define
for clock driver.
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Reviewed-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Rename the ast2500-scu.h to aspeed-clock.h.
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Reviewed-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
The commit 57805f2270 ("net: bcmgenet: Don't set ID_MODE_DIS when
not using RGMII") needed to be extended for the case of using the
rgmii-rxid. The latest version of the Rasbperry Pi4 dtb files for the
5.4 now specify the rgmii-rxid.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Tested-by: Petr Tesarik <ptesarik@suse.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
This commit fixes a serious issue occurring when several network
commands are run on a raspberry pi 4 board: for instance a "dhcp"
command and then one or several "tftp" commands. In this case,
packet recv callbacks were called several times on the same packets,
and send function was failing most of the time.
note: if the boot procedure is made of a single network
command, the issue is not visible.
The issue is related to management of the packet ring buffers
(producer / consumer) and DMA.
Each time a packet is received, the ethernet device stores it
in the buffer and increments an index called RDMA_PROD_INDEX.
Each time the driver outputs a received packet, it increments
another index called RDMA_CONS_INDEX.
Between each pair of network commands, as part of the driver
'start' function, previous code tried to reset both RDMA_CONS_INDEX
and RDMA_PROD_INDEX to 0. But RDMA_PROD_INDEX cannot be written from
driver side, thus its value was actually not updated, and only
RDMA_CONS_INDEX was reset to 0. This was resulting in a major
synchronization issue between the driver and the device. Most
visible behavior was that the driver seemed to receive again the
packets from the previous commands (e.g. DHCP response packets
"received" again when performing the first TFTP command).
This fix consists in setting RDMA_CONS_INDEX to the same
value as RDMA_PROD_INDEX, when resetting the driver.
The same kind of fix was needed on the TX side, and a few variables
had to be reset accordingly (c_index, tx_index, rx_index).
The rx_index and tx_index have only 256 entries so the bottom 8 bits
must be masked off.
Originated-by: Etienne Dublé <etienne.duble@imag.fr>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Tested-by: Petr Tesarik <ptesarik@suse.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
As the error message is now displayed by generic phy functions,
the dev_err/pr_err can be change to dev_dbg/pr_debug.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
As the error message is now displayed by generic phy functions,
the pr_err can be change to pr_debug.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
As the error message is now displayed by generic phy functions,
the pr_err can be change to pr_debug.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
As the error message is now displayed by generic phy functions,
the dev_err can be change to dev_dbg.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
- This patch moves sata phy powerup from dedicate phy to compphy
and adds invert option for sata powerup routine.
Change-Id: I1b4e8753e2b2c14c6efa97bca2ffc7d2553d8a90
Signed-off-by: zachary <zhangzg@marvell.com>
Signed-off-by: Ken Ma <make@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/53601
Reviewed-by: Igal Liberman <igall@marvell.com>
Tested-by: Igal Liberman <igall@marvell.com>
[a.heider: adapt to mainline]
Signed-off-by: Andre Heider <a.heider@gmail.com>
Tested-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The size returned by 'getvar partition-size' should be in bytes, not in
blocks as fastboot uses that value to generate empty partition when
running format [1].
Note that the function was already returning the proper size in bytes
for NAND devices (see struct part_info details).
[1]
https://android.googlesource.com/platform/system/core/+/refs/heads/android10-release/fastboot/fastboot.cpp#1500
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
It was revealed that when the fastboot_tx_write_str function is called
without the previously initialized fastboot_func->in_req->complete field,
a copy of in_req will be sent to the I/O requests queue without
an initialized field.
Moving a piece of code with the initializing of the
fastboot_func->in_req->complete field above transmit_tx allows to solve
this problem.
Fixes: 65c96757fe "usb: fastboot: Convert USB f_fastboot to shared fastboot"
Signed-off-by: yurii.pidhornyi <yurii.pidhornyi@globallogic.com>
Since the USB HID limits the maximum bandwidth(3072) for interrupt
endpoint transfers, when the bInterval set to 1, we can only support 3
boards to run sdp at the same time. In order to support more boards,
change the bInterval of interrupt endpoint to 3, which will not affect
the transmission speed.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
EP0 has been used to transfer file data in sdp before, but the max
packetsize of ep0 is 64 bytes. So in order to improve the file transfer
speed, here add the EP1_OUT interrupt endpoint which max packetsize is
set to 1024 byte.
After testing, it turns out that using ep1out is twice as fast as using
ep0 while receiving data in sdp.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add support to f_sdp to search and load iMX8 container image or iMX8M
FIT image by new UUU command SDPV.
When using the SDPV, the uuu will continue to send out data after first
level boot loader used by ROM. This means uuu won't skip to the offset
of the second boot loader, and the padding data before second boot loader
will be sent out. So we have to search the FIT header or container header
in the buffer that SDP received.
Also change to more common method to exit f_sdp handler not depending on
SPL_FIT_FOUND flag because container loader won't set this.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Because the buffer length of sdp usb request is 65, we have to allocate
65 bytes not 64 bytes. Otherwise there is potential buffer overflow.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Add HS endpoint descriptor for SDP. So that we can use high speed endpoint,
and the SDP device can send packet with 512 byte size.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
MAX3420 implements FullSpeed USB Device over SPI.
Another version MAX3421, also implements USB Host mode.
This driver should be good for the device mode of max3421 as well.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Default implementation of fastboot_set_reboot_flag function that depends
on "bcb" commands could be used in general case if there are no need to
make any platform-specific implementation, otherwise it could be
disabled via Kconfig option FASTBOOT_USE_BCB_SET_REBOOT_FLAG.
Please note that FASTBOOT_USE_BCB_SET_REBOOT_FLAG is mutually exclusive
with some platforms which already have their own implementation of this
function.
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
Android 10 adds support for dynamic partitions and in order to support
this userspace fastboot must be used[1]. New tool fastbootd is
included into recovery.
Userspace fastboot works from recovery and is launched if:
1) - Dynamic partitioning is enabled
2) - Boot control block has 'boot-fastboot' value into command field
The bootloader is expected to load and boot into the recovery image
upon seeing boot-fastboot in the BCB command. Recovery then parses the
BCB message and switches to fastbootd mode[2].
Please note that boot script is expected to handle 'boot-fastboot'
command in BCB and load into recovery mode.
Bootloader must support 'reboot fastboot' command which should reboot
device into userspace fastboot to accomodate those changes[3].
Another command that bootloader must support[3] is 'reboot recovery'. This
command should simply reboot device into recovery mode.
[1] - https://source.android.com/devices/bootloader/fastbootd
[2] - https://source.android.com/devices/bootloader/fastbootd#unified_fastboot_and_recovery
[3] - https://source.android.com/devices/bootloader/fastbootd#modifications_to_the_bootloader
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
Signed-off-by: Roman Stratiienko <r.stratiienko@gmail.com>
Change-Id: I9d2bdc9a6f6f31ea98572fe155e1cc8341e9af76
Extend fastboot_set_reboot_flag arguments with reboot reason so that
it could handle different reboot cases in future.
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
The environment variable loadaddr is in the virtual address space of the
sandbox. To get the actual memory address where the FIT image has been
loaded we have to convert this address according to the memory mapping of
the sandbox.
Equally the addresses in the *.its file have to be converted when used in
the dfu_ram driver.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add support for defining raw fastboot partitions in eMMC by specifying
the offset and size in an environment variable. Optionally, the eMMC
hardware partition number may also be specified.
This makes it possible to e.g. update only part of the eMMC boot
partition, instead of having to write the entire partition.
Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
When unregister gadget driver in ci_udc, the usb device is not
removed or stop. This causes next "usb start" fails to work.
Add a new interface "usb_remove_ehci_gadget" in usb-uclass to
remove the usb device for DM driver. Using "usb_lowlevel_stop" for
non-DM driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The usb mass storage (f_mass_storage.c) uses fixed usb index 0,
this causes problem while CDNS3 USB controller index is 1.
Modify the API of fsg to pass the controller index.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The original rtl_clear_bp() is used to clear the firmware of both
PLA and USB MCU. The new one could clear the firmware of PLA or
USB independently. It is unnecessary to clear firmware, if there
is no one to be updated.
Besides, clear the firmware by writing the relative registers in
bulk.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Reset bmu after disabling Tx/Rx. This is used to clear the FIFO of
Tx/Rx. The remained data may be transferred after Tx/Rx is re-enabled.
And it results in garbage data.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
If the SCIF is receiving data quickly enough, it may happen that the
SCxSR_RDxF flag is cleared in sh_serial_getc_generic(), while the
FIFO still contains data. If that happens, the serial_getc_check()
reports no data in the FIFO as the flag is no longer set. Add one
more check, if the SCxSR_RDxF is not set, read out the FIFO level
and if there are still characters in the FIFO, permit reading them
out.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Fix this typo in the Kconfig help.
Suggested-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
For proper initialization of aardvark pci driver it is required to
de-assert reset GPIO. So depeneds on DM_GPIO option.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
- The SDIO signal voltage and max base clock frequency
setting are missing in driver, which causes SDIO
not working.
- The patch adds SDIO signal voltage switch support,
which is based on regulator-gpio of vqmmc-supply, and
sets the max base clock frequency.
- Fix the zero clock value in call to sdhci_setup_cfg()
function.
Change-Id: I79c8860c65b8db166f4f70db56ede4097f71f1fa
Signed-off-by: Evan Wang <xswang@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/53589
Reviewed-by: Hua Jing <jinghua@marvell.com>
Tested-by: Hua Jing <jinghua@marvell.com>
[pali: Amended fixup patch]
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
This change ensures that PCIe card is put into reset state when U-Boot
stops using it.
DM_FLAG_OS_PREPARE ensures that U-Boot executes driver's remove callback
prior booting Linux kernel.
Linux kernel pci-aardvark driver needs to reset PCIe card via PERST# signal
prior initializing it. If it does not issue reset then some PCIe cards
(specially Compex WiFi cards) are not detected at all.
Putting PCIe card into reset state prior booting Linux kernel would ensure
that card would be properly reset at time when Linux kernel starts
initializing pci-aardvark driver.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Tested-by: Andre Heider <a.heider@gmail.com>
Change active-high to active-low and change DT property name from
reset-gpio to reset-gpios. This format of gpio reset is used by
pci-aardvark driver in Linux kernel.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Tested-by: Andre Heider <a.heider@gmail.com>
With ABI 3.0, sysfw deprecated special resource types used for AM65x
SoC. Instead started using device id as resource type similar to the
convention used in J721E SOC.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
There is missing dependency for PCIE_ROCKCHIP which selects
PHY_ROCKCHIP_PCIE which directly depends on ARCH_ROCKCHIP.
WARNING: unmet direct dependencies detected for PHY_ROCKCHIP_PCIE
Depends on [n]: ARCH_ROCKCHIP [=n]
Selected by [y]:
- PCIE_ROCKCHIP [=y] && PCI [=y]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The indentation was messing up with the scripts/build-whitelist.sh that
was marking SYS_USB_EVENT_POLL_VIA_INT_QUEUE (and probably also the
other indented options) erroneously as ad-hoc configure option with the
following error:
```
Error: You must add new CONFIG options using Kconfig
The following new ad-hoc CONFIG options were detected:
CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE
```
All platforms support bi_dram[] since quite some time. Lets remove the
and bi_memsize values completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since commit 86cf1c8285 ("configs: Migrate CONFIG_NR_DRAM_BANKS") &
commit 999a772d9f ("Kconfig: Migrate CONFIG_NR_DRAM_BANKS"),
CONFIG_NR_DRAM_BANKS is always defined with a value (4 is default).
It makes no sense to still carry code that is guarded with
"#ifndef CONFIG_NR_DRAM_BANKS" (and similar). This patch removes
all these unreferenced code paths.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Add basic Marvell/Cavium OcteonTX/TX2 support (Suneel)
- Infrastructure changes to PCI uclass to support these SoC's (Suneel)
- Add PCI, MMC & watchdog driver drivers for OcteonTX/TX2 (Suneel)
- Increase CONFIG_SYS_MALLOC_F_LEN for qemu-x86 (Stefan)
- Sipeed Maix support S-mode.
- Provide command sbi.
- Use fdtdec_get_addr_size_auto_parent to get fu540 cache base address.
- Fix a compiler error with CONFIG_SPL_SMP=n.
- Fix sifive ram driver 32 compiler warnings.
- Fix kendryte/pll.h redefine nop() warning.
Adds support for Core 0 watchdog poke on OcteonTX and OcteonTX2
platforms.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adds support for MMC controllers found on OcteonTX or
OcteonTX2 SoC platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Cc: Peng Fan <peng.fan@nxp.com>
Adds support for PCI ECAM/PEM controllers found on OcteonTX
or OcteonTX2 SoC platforms.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
For SATA controller found on OcteonTX SoC's, use non-standard PCI BAR0
instead of BAR5.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add check if the referenced ofnode is valid.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
If ARI capability is found on device, use it to update next function
number in bus scan and also helps to skip unnecessary bdf scans.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Makes dm_pci_map_bar API available to map BAR for Virtual function
PCI devices which support Enhanced Allocation.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
SR-IOV - Single Root I/O Virtualization
PF - Physical Function VF - Virtual Function
If SR-IOV capability is present, use it to initialize Virtual Function
PCI device instances. pci_sriov_init function will read SR-IOV
registers to create VF devices under the PF PCI device and also bind
driver if available. This function needs to be invoked from Physical
function device driver which expects VF device support, creating
minimal impact on existing framework.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
If Enhanced Allocation capability is present in bridges, use it
to read the fixed sub-ordinate bus number.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Enable PCI memory regions in ranges property to be of multiple entry.
This helps to add support for SoC's like OcteonTX/TX2 where every
peripheral is on PCI bus.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Fix for the case of a U-Boot configuration with CONFIG_SPL,
CONFIG_I2C_MUX, CONFIG_I2C_MUX_PCA954x, no CONFIG_SPL_DM and no
CONFIG_SPL_I2C_MUX. Without this fix linking of pca954x fails because
dm_write_i2c does not exist because CONFIG_SPL_DM is not defined.
Signed-off-by: Kees Trommel <kees.trommel.contractor@draeger.com>
Cc: Heiko Schocher <hs@denx.de>
This patch fixes a few issues noticed, when testing this new driver on
ARM Octeon TX2 again. Here the details:
- Remove "common.h" header inclusion
- Use correct THP define on Octeon TX2
- Octeon TX2 uses the same compatible as Octeon TX. We can't distinguish
both platforms this way. Remove the unused "cavium,thunder2-99xx-twsi"
compatible and add a check to the Octeon TX2 specific
"cavium,thunderx-i2c" so that the correct driver data is selected.
- Removed "struct pci_device_id" definition and U_BOOT_PCI_DEVICE()
as its not needed for the PCI based probing on Octeon TX2
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Suneel Garapati <sgarapati@marvell.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Parse subnode DT properties only if parent node is valid.
Otherwise, assert is triggered on ofnode_valid in ofnode_first_subnode
from dev_for_each_subnode.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Fix argument ordering for map_physmem() called in dm_pci_map_ea_bar().
Additinally minor spelling correction.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Instead of using a fixed length pre-allocated array of regions, this
patch moves to dynamically allocating the regions based on the number
of available regions plus the necessary regions for DRAM banks.
Since MAX_PCI_REGIONS is not needed any more, its removed completely
with this patch.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Since the migration to Kconfig, CONFIG_NR_DRAM_BANKS is configured for
all boards. Hence we can remove the conditional compilation and the code
path that will never get compiled.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
priv->info.size is of type 'size_t' but the length modifier is l.
Fix this by casting priv->info.size. Note 'z' cannot be used as
the modifier as SPL does not support that.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@openfive.com>
Cleaning up the following:
ERROR: do not use assignment in if condition
#281: FILE: drivers/xen/pvblock.c:260:
+ if ((err = xenbus_switch_state(XBT_NIL, nodename,
CHECK:COMPARISON_TO_NULL: Comparison to NULL could be written "err"
#52: FILE: drivers/xen/pvblock.c:298:
+ if (err != NULL) {
ERROR: do not use assignment in if condition
#176: FILE: drivers/xen/gnttab.c:103:
+ if ((flags = nflags) & (GTF_reading | GTF_writing)) {
WARNING: Missing or malformed SPDX-License-Identifier tag in line 1
#329: FILE: include/xen/gnttab.h:1:
+/*
WARNING: Misplaced SPDX-License-Identifier tag - use line 1 instead
#330: FILE: include/xen/gnttab.h:2:
+ * SPDX-License-Identifier: GPL-2.0
ERROR: do not use assignment in if condition
#630: FILE: lib/sscanf.c:558:
+ if ((n = inr) < width) {
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
after review of sam copyright should be on one line and link should
not between author lines
just remove the link and put ryder first as he is author of linux-driver
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
make the shared reg optional when version is v1 for sata
Suggested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
'log2blksz' in blk_desc structure must always be initialized, otherwise
it will cause a lot of weird failures in file operations.
For example, fs_set_blk_dev[_with_part]() examines a block device against
every file system with its probe function. In particular, ext4 file
system's ext4_probe() will calls fs_devread() to fetch a super block.
If log2blksz is 0, the actual 'read' size, i.e. block_len >> log2blksz, is
much bigger than a buffer's size, and it can end up with memory corruption.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Fixes: f4802209e5 ("virtio: Add block driver support")
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
There is no reason to bind psci driver if U-Boot runs in EL3 because
SMC/HVC instructions can't be called. That's why detect this state and
don't let user to crash from prompt by performing reset or poweroff
commands (if enabled).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
- Add CCF clocks definitions for iMX6Q enet (ETH)
- Several fixes for CCF framework - the most notable is the one, which
adds get_rate helper to clk-mux.c
- Improvements for clk command - better visibility and alignment.
After adding custom get_rate helper function it was necessary to include
<dm/uclass.h> to avoid warnings about missing uclass_get_device_by_name.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Series-to: u-boot
The previous version of the get_rate helper does not work if the mux
clock parent is changed after the probe. This error has not been
detected because this condition has not been tested. The error occurs
because the set_parent helper does not change the parent of the clock
device but only the clock selection register. Since changing the parent
of a probed device can be tricky, the new version of the get_rate helper
provides the rate of the selected clock and not that of the parent.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
The tests developed for the mux clock are run on the sandbox. They don't
call the clk_mux_set_parent routine and therefore they do not detect
this error.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
The parent->name variable can be used only in case the
uclass_get_device_by_name routine returns successfully.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
The top-level framework flags are passed as parameter to the common
clock framework (ccf) registration routines without being used.
Checks of the flags setting added by the patch have been added in the
ccf test.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Unlike the other clock types, in the case of the gated clock, a new
driver has been developed which does not use the registering routine
provided by the common clock framework.
The addition of the ecspi0 clock to sandbox therefore allows testing
the ccf gate clock.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
After commit 673f659732 ("net: fec_mxc: support i.MX8M with CLK_CCF") all
NXP boards, which are not IMX8 and in the same time are supporting CCF need
to provide PTP clock.
On the i.MX6Q this clock is provided with IMX6QDL_CLK_ENET_REF in the Linux
kernel's CCF.
Code in this change models the simplest case when enet reference clock is
generated from 'osc' clock.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This code has been ported from Linux kernel v5.5.5 (tag) and has been
adjusted to U-Boot's DM.
It adds support for correct recognition of IMX_PLLV3_ENET flag in the
clk-pllv3.c driver.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
After commit 673f659732 ("net: fec_mxc: support i.MX8M with CLK_CCF") all
NXP boards, which are not IMX8 and in the same time are supporting CCF
need to provide IMX6QDL_CLK_ENET.
This change defines the missing clock in i.MX6Q's CCF.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Do not calculate a unused value of n which is overwritten in both branches
of the subsequent if statement.
Identified by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
binman fixes for portage
various minor fixes
'bind' command improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl9BbZcRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZZiQf/UVsriftmxdDz3Lvbz7Jw6UCBXbeM3UN8
KgRxVll3kurZeu8bIcjAPY4YRrbWRqSXmZTXpZWgbyZzHLM4RnkamY3KF3DoxPjc
cbskd/fr4nPjSZVFrkzrvD+D5bhm+VrMtf861AkbAqqpG+Q1FmWHgApqOL1fXn3s
2VoMxRz8Cn9KkSDmxaCtJnLX77GVYYdfgii7RuNWGDqr3eBWrzflV38VbPHLplEg
VLqaLBe3G4zVwElA9Nc2hXpZB84KZEETHcBnmCzNkrSYTN2ofvSeZrWbtRztQFhz
yKur1y7jFsryRkMfxBzgldsKFRNnPT9vr+0qGtrztHjCmvhDkx1YMg==
=iDRJ
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-22aug20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
replace devfdt_get_addr_ptr() with dev_read_addr_ptr()
binman fixes for portage
various minor fixes
'bind' command improvements
This converts the following to Kconfig:
CONFIG_SPLASH_SCREEN
CONFIG_SPLASH_SCREEN_ALIGN
CONFIG_SPLASHIMAGE_GUARD
CONFIG_SPLASH_SOURCE
Signed-off-by: Simon Glass <sjg@chromium.org>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To help this tedious work, this commit converts devfdt_get_addr_ptr()
to dev_read_addr_ptr() by coccinelle. I also removed redundant casts
because dev_read_addr_ptr() returns an opaque pointer.
To generate this commit, I ran the following semantic patch
excluding include/dm/.
<smpl>
@@
type T;
expression dev;
@@
-(T *)devfdt_get_addr_ptr(dev)
+dev_read_addr_ptr(dev)
@@
expression dev;
@@
-devfdt_get_addr_ptr(dev)
+dev_read_addr_ptr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is strange to use devfdt_get_addr_ptr(), then cast the pointer
back to ulong because you could use devfdt_get_addr() without casting.
Convert it to dev_read_addr(), which is capable to CONFIG_OF_LIVE.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Stefan Roese <sr@denx.de>
It is strange to use devfdt_get_addr_ptr(), then cast the pointer
back to uint32 because you could use devfdt_get_addr() without casting.
Convert it to dev_read_addr(), which is capable to CONFIG_OF_LIVE.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
According to the description of devfdt_get_addr_ptr, this function should
return NULL on failure, but currently it returns (void *)FDT_ADDR_T_NONE.
Fix this by making devfdt_get_addr_ptr return NULL on failure, as
described in the function comments. Also, update the drivers currently
checking (void *)FDT_ADDR_T_NONE to check for NULL.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add driver data to existing compatible string "sandbox,phy".
Add an additional compatible string without driver_data
This will verify that bind command parses, finds and passes the
correct driver data to device_bind_with_driver_data() by using
driver_data in the second sandbox_phy_ids table entry.
In sandbox_phy_bind() a check is added to validate driver_data
content.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the case of the live tree ofnode_read_addr_cells() and
ofnode_read_size_cells() return the #address-cells and #size-cells defined
in the parent node. With the patch the same is done for a non-live tree.
The only consumer of these functions is currently the CFI flash driver.
This patch fixes the incorrect parsing of the device tree leading to
'saveenv' failing on qemu_arm64_defconfig.
For testing qemu-system-aarch64 has to be called with
-drive if=pflash,format=raw,index=1,file=envstore.img
to provide the flash memory. envstore.img must be 64 MiB large.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
There is no reason to have firmware specific structure in clock driver.
Move it to generic location and also initialize enum values which is based
on https://lore.kernel.org/linux-arm-kernel/20200318125003.GA2727094@kroah.com/
recommended way to go to make sure that values guaranteed by compiler.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Instead of recasting and shifting use macros which are designed for taking
upper/lower 32bit value from 64bit variable.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The capabilities register has a field to indicate whether the host
supports high speed mode or not. Add high speed host_caps based on
this bit instead of enabling it by default.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Michal Simek <michal.simek@xilnx.com>
Tested-by: Michal Simek <michal.simek@xilnx.com>
(zcu104 with sdhci-caps-mask = <0 0x200000>;)
Current IPI module register description is not align with IPI HW. The
registers with the wrong offset are not used so it does not cause real
issues. This patch aligns the register description.
Additionally comments added to explain why recv function does not check
any flag prior copying rx data.
Fixes: 660b0c77d8 ("mailbox: zynqmp: ipi mailbox driver")
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch merges ZynqMP firmware calls under xilinx_pm_request in order
to make trainsparent the EL. Calls at EL3 are send through IPI messages
and EL2 through SMC calls.
The EL2 call uses fixed payload and arg size as the EL3 call. The
firmware is capable to handle PMUFW_PAYLOAD_ARG_CNT bytes but the
firmware API is limited by the SMC call size.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Removes duplicated definition of PAYLOAD_ARG_CNT and define it in the
firmware driver. Additionally fixes payload buffer declarations without
macro usage
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DT binding is saying that default value is 0 not -1 that's why fix it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
s/xlnx,mio_bank/xlnx,mio-bank/g
DT binding is describing mio-bank not mio_bank that's why fix all DTSes and
also driver itself.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Remove adhoc dt binding for fixed-partition definition for i2c eeprom.
fixed-partition are using reg property instead of offset/size pair.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Zynq/ZynqMP/Versal IPs should be possible to called also from Microblaze in
PL and vice versa. That's why change dependencies and do not limit enabling
just for some platforms.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
add support for PHY_TYPE_SATA to Mediateks TPHY driver
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
This patch adds PCIe support for the Mediatek MT7622 SOC.
Signed-off-by: Chuanjia Liu <Chuanjia.Liu@mediatek.com>
Signed-off-by: Henry Yen <henry.yen@mediatek.com>
This patch adds pciesys support in clock driver for
MediaTek MT7622 SoC.
Signed-off-by: Henry Yen <henry.yen@mediatek.com>
Signed-off-by: Chuanjia Liu <Chuanjia.Liu@mediatek.com>
Free resources used by Xen board before jumping to Linux kernel.
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Implement Xen para-virtual frontend to backend communication
and actually read/write disk data.
This is based on mini-os implementation of the para-virtual block
frontend driver.
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Read essential virtual block device configuration data from XenStore,
initialize front ring and event channel.
Update block device description with actual block size.
Use code for XenStore from mini-os.
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Add initial infrastructure for Xen para-virtualized block device.
This includes compile-time configuration and the skeleton for
the future driver implementation.
Add new class UCLASS_PVBLOCK which is going to be a parent for
virtual block devices.
Add new interface type IF_TYPE_PVBLOCK.
Implement basic driver setup by reading XenStore configuration.
Signed-off-by: Andrii Anisov <andrii_anisov@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Make required updates to run on u-boot.
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Make required updates to run on u-boot and strip test code.
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Add wait_event_timeout - sleep until a condition gets true or a
timeout elapses.
This is a stripped version of the same from Linux kernel with the
following u-boot specific modifications:
- no wait queues supported
- use u-boot timer to detect timeouts
- check for Ctrl-C pressed during wait
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
[trini: Drop atomic_read from gadget/ether.c as this has existed for a
while and now causes problems]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support for Xen para-virtualized serial driver. This
driver fully supports serial console for the virtual machine.
Please note that as the driver is initialized late, so no banner
nor memory size is visible.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make required updates to run on u-boot. Strip functionality
not needed by U-boot.
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Port hypervisor related code from Mini-OS. This is referencing the code
of Mini-OS from [1] by Huang Shijie and Volodymyr Babchuk which is for
ARM64.
Update essential arch code to support required bit operations, memory
barriers etc.
Copyright for the bits ported belong to at least the following authors,
please see related files for details:
Copyright (c) 2002-2003, K A Fraser
Copyright (c) 2005, Grzegorz Milos, gm281@cam.ac.uk,Intel Research Cambridge
Copyright (c) 2014, Karim Allah Ahmed <karim.allah.ahmed@gmail.com>
[1] - https://github.com/zyzii/mini-os.git
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
[trini: Drop wmb() from musb-net/linux-compat.h now]
Signed-off-by: Tom Rini <trini@konsulko.com>
- Add STM32 FMC2 EBI controller driver
- Fix dwc3-sti-glue which allows STiH410-B2260 to boot again
- Add fitImage its entry for 587-200 DHCOR SoM
- Add both PDK2 and DRC02 DT into DHCOM fitImage its
- Fix DHCOM KS8851 ethernet MAC address
- Remove stm32mp1 board.c file
- Use const for struct node_info in board stm32mp1.c file
-----BEGIN PGP SIGNATURE-----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=J4aq
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200813' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Use IS_ENABLED to prevent ifdef in board_key_check for STM32MP
- Add STM32 FMC2 EBI controller driver
- Fix dwc3-sti-glue which allows STiH410-B2260 to boot again
- Add fitImage its entry for 587-200 DHCOR SoM
- Add both PDK2 and DRC02 DT into DHCOM fitImage its
- Fix DHCOM KS8851 ethernet MAC address
- Remove stm32mp1 board.c file
- Use const for struct node_info in board stm32mp1.c file
FMC2 EBI support has been added. Common resources (registers base
address and clock) can now be shared between the 2 drivers using
"st,stm32mp1-fmc2-nfc" compatible string. It means that the
common resources should now be found in the parent device when EBI
node is available.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The driver adds the support for the STMicroelectronics FMC2 EBI controller
found on STM32MP SOCs.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch renames functions and local variables.
This cleanup is done to get all functions starting by stm32_fmc2_nfc
in the FMC2 raw NAND driver when all functions will start by
stm32_fmc2_ebi in the FMC2 EBI driver.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
FMC2_TIMEOUT_5S will be used each time that we need to wait.
It was seen, during stress tests in an overloaded system,
that we could be close to 1 second, even if we never met this
value. To be safe, FMC2_TIMEOUT_MS is set to 5 seconds.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Remove inline comments that are useless since function label are
self explanatory.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The chip select defined in the device tree could only be 0 or 1.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
node varaible is used as iterator into ofnode_for_each_subnode()
loop, when exiting of it, node is no more a valid ofnode.
Use dwc3_node instead as parameter of ofnode_valid()
Fixes: ac28e59a57 ("usb: Migrate to support live DT for some driver")
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Add device identification for J7200 SoC
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
k3-j721e ddr driver sanity checks for product id and version number.
Version number gets changed for every minor update in the IP. So discard
the version check and just sanity check for product id.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The hardcoded array size leads to array overflows with changes in
speed modes enum in mmc core. Use MMC_MODES_END for otap_del_sel
array declaration to fix this.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This is based on the Linux kernel driver for the RTI watchdog.
To actually reset the system on an AM65x, it requires firmware running
on the R5 that accepts the NMI and issues the actual system reset via
TISCI. Kind of an iTCO, except that this watchdog hardware has support
for no-way-out, and only for that.
On the J721E, reset works without extra firmware help when routing the
RTI interrupt via the ESM.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Add Cortina Access LED controller support for CAxxxx SOCs
Signed-off-by: Jway Lin <jway.lin@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Simon Glass <sjg@chromium.org>
Add head file fixed link error and remove unused flashing function
Reviewed-by: Simon Glass <sjg@chromium.org>
Extend manual relocation of block_cache list pointers to all platforms that
enable CONFIG_NEEDS_MANUAL_RELOC. Remove m68k-specific checks and provide a
single implementation that adds gd->reloc_off to the pre-relocation
pointers.
Acked-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Tested-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
[trini: Add guard around DECLARE_GLOBAL_DATA_PTR to avoid size growth]
Signed-off-by: Tom Rini <trini@konsulko.com>
serial_initialize is called only during the common init sequence, after
relocation (in common/board_r.c). Because it has a void return value, it
has to wrapped in initr_serial. In order to be able to get rid of this
indirection, make serial_initialize return int.
Remove extern from prototype in order to silence the following checkpatch
warning:
check: extern prototypes should be avoided in .h files
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Use IS_ENABLED() instead of #ifdef in blk_post_probe function.
No functional change intended.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
[trini: Fix thinko and use CONFIG_HAVE_BLOCK_DEVICE in IS_ENABLED()]
Signed-off-by: Tom Rini <trini@konsulko.com>
Some platforms, like MIPS Octeon, use mapped addresses (virtual address
!= physical address). On these platforms we need to make sure, that the
local virtual addresses are converted to physical (DMA) addresses for
the xHCI controller. This patch adds the missing virt_to_phys() calls,
so that the correct addresses are used.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
These values are already swapped to CPU endianess, so swapping them
again is a bug. Let's remove the swap here instead.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
xhci_writeq() makes the CPU->LE swapping only when addressing registers
in the xHCI controller address range and not in the local memory (RAM).
We need to use cpu_to_le64() here to ensure that the conversion is done
correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
While trying to use the U-Boot xHCI driver on the MIPS Octeon platform,
which is big endian, I noticed that the driver is missing a few endian
conversion calls. This patch adds these missing endian conversion
calls.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Add configuration flag to select the supported dwc driver configuration:
- CONFIG_DWC_ETH_QOS_TEGRA186
- CONFIG_DWC_ETH_QOS_IMX
- CONFIG_DWC_ETH_QOS_STM32
See Linux driver ethernet/stmicro/stmmac and associated glue layers
for other configuration examples.
This patch removes the not-selected compatibles and lets the linker remove
the unused functions to reduce the size of the driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Move the variable psci_method in .data section when EFI is not
activated and the psci driver safely access it before relocation.
Without this patch the variable is located in .bss section
and the psci probe requested before relocation corrupts the device
tree (probe is requested by board_f.c::print_resetinfo()).
When EFI_LOADER is activated, this variable in already located in the
.data.efi_runtime section by __efi_runtime_data.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
In the unlikely event that both blocks 10 and 11 are marked as bad (on a
32 bit machine), then the process of marking block 10 as bad stomps on
cached entry for block 11. There are (of course) other examples.
Signed-off-by: Patrick Doyle <pdoyle@irobot.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
-----------
- fixes for Toradex board
- fix warnings from previous PR
- HAB: reset instead of panic after failure
- new board: MYiR Tech MYS-6ULX
- mx6cuboxi: use OF_PLATDATA
- further changes for DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCXykjtQ8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76a1WQCcD+objdS+90mDdT0yTpW3jHS4YiwAn2V2rTTo
4hKj5yxRg3cvb/pBAmbQ
=TyRs
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20200804' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
For 2020.10
-----------
- fixes for Toradex board
- fix warnings from previous PR
- HAB: reset instead of panic after failure
- new board: MYiR Tech MYS-6ULX
- mx6cuboxi: use OF_PLATDATA
- further changes for DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
This header file should not be included in other header files. Remove it
and use a forward declaration and un-inlining of dev_get_clk_ptr()
instead.
Fix up the kendryte header files to avoid build errors.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
This header file should not be included in other header files. Remove it
and use a forward declaration instead.
Also move the inline function out into a C file. We should not include C
code in headers.
Signed-off-by: Simon Glass <sjg@chromium.org>
This header file should not be included in other header files. Remove it
and use a forward declaration instead.
Also drop asm/io.h
Signed-off-by: Simon Glass <sjg@chromium.org>
This header file should not be included in other header files. Remove it
and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
This header file should not be included in other header files. Remove it
and use a forward declaration instead.
Drop the common.h inclusion also.
Signed-off-by: Simon Glass <sjg@chromium.org>
This file should not include common.h and dm.h so remove them. Also move
the inclusion of this file to after the normal includes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This header file should not be included in other header files. Remove it
and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
This header file should not be included in other header files. Remove it
and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
The -ENODEV error value in spi_nor_read_id() is incorrect since there
clearly is a device - it just cannot be supported. Use -ENOMEDIUM instead
which has the virtue of being less common.
Fix the return value in spi_nor_scan().
Also there are a few printf() statements which should be debug() since
they bloat the code with unused strings at present. Fix those while here.
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases SPL needs to be able to erase but TPL just needs to read.
Allow these to have separate settings for SPI_FLASH_TINY.
Signed-off-by: Simon Glass <sjg@chromium.org>
PRCI module within SiFive SoC's has register with which we can
reset the sub-systems within the SoC. The resets to DDR and ethernet
sub systems within FU540-C000 SoC are active low, and are hold low
by default on power-up. Currently these are directly asserted within
prci driver via register read/write.
With the DM based reset driver support here, we bind the reset
driver with clock (prci) driver and assert the reset signals of
both sub-system's appropriately.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Pragnesh Patel <Pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Indexes of reset signals available in PRCI driver are also
defined in include/dt-bindings/reset/sifive-fu540-prci.h.
So use those instead of defining new ones again within the
fu540-prci driver.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Since commit 7812bbdc37 ("video: Correctly handle multiple
framebuffers") the vidconsole output is missing on the primary
display on boards with two IPU units (all i.MX6Q/D based boards).
The base address of the allocated framebuffer is not correctly
programmed in the display controller. Fix it.
Reported-by: Soeren Moch <smoch@web.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Soeren Moch <smoch@web.de>
Adds support for SPI controllers found on Octeon II/III and Octeon TX
TX2 SoC platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds a simple clock driver for the Marvell Octeon MIPS SoC
family. Its for IO clock rate passing via DT in some of the Octeon
driver, like I2C. So that we don't need to use the non-mainline API
octeon_get_io_clock().
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Lukasz Majewski <lukma@denx.de>
Add support for GPIO controllers found on Octeon II/III and Octeon TX
TX2 SoC platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Continuing with the approach in commit <addf358bac1d2bd0> rename
additional drivers to allow the OF_PLATDATA support.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
After enabling OF_PLATDATA support to both MMC and GPIO drivers add the
support for card detection.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Continuing with the OF_PLATADATA support for iMX6 to reduce SPL
footprint, add it to mxc_gpio. Thanks to this, it will be possible to
enable card detection on MMC driver.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
In order to reduce the footprint of SPL by removing dtb and library
overhead, add OF_PLATDATA support to fsl_esdhc_imx. This initial
approach does not support card detection, which will be enabled after
adding OF_PLATDATA support to GPIO.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As discussed in commit <addf358bac1d2bd0> rename fsl_esdhc_imx
driver to allow the OF_PLATDATA support.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In our Python tests we expect to see the word "resetting". It may be
truncated if we reset before the serial console buffer is transferred.
Wait for 100 ms between the "resetting ..." message and the actual reset
like we do when powering off.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Refactor to allow any arch to create SPI-flash images
New button uclass
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl8g33sRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreaeEgf/QhmJjd6lEE3ABncRa3texyqq7j9eu+9P
2JMCahrIzps83LLOkzNSGs1+m1hRuTcdnYNV8FxdmkAjDTYwV5RHOfwtpAr2nkH2
HBbJRA2qMPleqT8wcymouhaCIRTTCGfUkFgZ+OowwSlHnQ4d2oGU/59Z+AkbpfX0
3svA1Mlr5rUTZ3qTvdsepuZckuYOTGYZ5jgjbgr+G8F4iW4Ov+OkBxqDz9zFCveF
md5CHKP1SV+bq67Q9uqUEwatLzYpy1p24j1Qe4G08U1+XCi6r+95VEc7TWxggboj
eV/5d/sZbGESAtJiJ4TmqpGVcOLzBLI0FOunky0JNFwdcyRS/6KcCg==
=Xjil
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-28jul20' of git://git.denx.de/u-boot-dm
Use binman instead of one of the Rockchip build scripts
Refactor to allow any arch to create SPI-flash images
New button uclass
- fix SPL boot issue due to early dbgmcu_init() call
- fix SPL boot issue due to dcache memory region configuration
- add support of CONFIG_ENV_IS_IN_MMC
- add specific SD/eMMC partition for U-Boot enviromnent
- enable env in SPL
- use "env info -q" to remove log during boot
- remove env location override for dh_stm32mp1
- update management of misc_read
- check result of find_mmc_device in stm32prog
- use regulator_set_enable_if_allowed for disabling vdd supply in usbphyc
- enable CMD_ADTIMG flag to handle Android images
- device tree alignment with Linux Kernel v5.8-rc1
- remove hnp-srp-disable for usbotg on dk1
- add reset support to uart nodes on stm32mp15x
- use correct weak function name spl_board_prepare_for_linux
- use cd-gpios for ST and DHSOM boards
- add seeed studio odyssey-stm32mp157c board support
- move ethernet PHY into SoM DT
- add DHSOM based DRC02 board support
Add optee based bnxt fw load driver.
bnxt is Broadcom NetXtreme controller Ethernet card.
This driver is used to load bnxt firmware binary using OpTEE.
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- nexell_display.c: Changed to DM, CONFIG_FB_ADDR can not be used
anymore because framebuffer is allocated by video_reserve() in
video-uclass.c. Therefore code changed appropriately.
- '#ifdef CONFIG...' changed to 'if (IS_ENABLED(CONFIG...))' where
possible (and similar).
- livetree API (dev_read_...) is used instead of fdt one (fdt...).
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
Low level functions for DPC (Display Controller) and Makefile for all
nexell video low level functions.
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- livetree API (dev_read_...) is used instead of fdt one (fdt...).
- doc/device-tree-bindings/pinctrl/nexell,s5pxx18-pinctrl.txt added.
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- driver changed to DM.
- pinctrl-driver/dt is used now instead of configuring the mmc I/O-pins
in the mmc-driver.
- nexell_dwmmc_ofdata_to_platdata() reworked, i.e. valid default values
are used now (where possible) and the appropriate if-blocks have
been removed.
- new dt-property "mmcboost" is used now instead of "CONFIG_BOOST_MMC"
which was not defined anywhere.
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- i2c/nx_i2c.c: Some adaptions mainly because of changes in
"struct udevice".
- several Bugfixes in nx_i2c.c.
- the driver has been for s5p6818 only. Code extended appropriately
in order s5p4418 is also working.
- "probe_chip" added.
- pinctrl-driver/dt is used instead of configuring the i2c I/O-pins
in the i2c-driver.
- '#ifdef CONFIG...' changed to 'if (IS_ENABLED(CONFIG...))' where
possible (and similar).
- livetree API (dev_read_...) is used instead of fdt one (fdt...).
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- livetree API (dev_read_...) is used instead of fdt one (fdt...).
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
Snapdragon SoCs and IPQ40xx use common TLMM IP,
so existing driver supports IPQ40xx as well.
So lets simply add a compatible for IPQ40xx.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
IPQ40xx and currently supported Snapdragon boards don't use the same one
so enable reading it from DT, if no DT property is found default value
is the same as the previous define.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
The pins for the MMC controller weren't being set up correctly because the
pinctrl driver only sets the GPIO pullup/pulldown config and doesn't
handle the special cases with PUPD/R0/R1 control.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
The sgmii mode init flow is almost the same for all mediatek SoC, the
only difference is the register offset(SGMSYS_GEN2_SPEED) is 0x2028
in the old chip(mt7622) but changed to 0x128 for the newer chip(mt7629
and the following chips).
Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
Add a simple driver which allows use of buttons attached to GPIOs.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Add a new uclass for button that implements two functions:
- button_get_by_label
- button_get_status
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
After latest improvements on OF_PLATDATA struct names are generated
based on driver name instead of compatible strings. With this in mind,
using aliases in drivers are not longer needed.
This patch removes code that tried to handle these kind of aliases to
improve readability.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use regulator_set_enable_if_allowed() api instead of regulator_set_enable()
while disabling vdd supply. This way the driver doesn't see an error
when disabling an always-on regulator.
This patch is needed since the commit f93fab3126 ("Revert 'power:
regulator: Return success on attempt to disable an always-on regulator'")
and use the API introduced by commit cc4a224af2 ("power: regulator:
Introduce regulator_set_enable_if_allowed api").
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
- Bug fixes and updates on ls2088a,ls1028a, ls1046a, ls1043a, ls1012a
- lx2-watchdog support
- layerscape: pci-endpoint support, spin table relocation fixes and
cleanups
- fsl-crypto: RNG support and bug fixes
This checks and handles RX errors on the Amlogic UART controller
after experiencing errors on the Khadas VIM3 & VIM3L when UART AO A
lines are not connected.
When the RX line is not connected, the first byte is erroneous and breaks
the U-Boot autoboot, breaking automatic boot.
This checks and drops any erroneous RX byte on pending and getc callbacks
to avoid returning true to pending when an error byte is in the FIFO.
Fixes: bfcef28ae4 ("arm: add initial support for Amlogic Meson and ODROID-C2")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Guillaume La Roque <glaroque@baylibre.com>
Currently checkpatch is not happy about this file:
total: 14 errors, 2 warnings, 7 checks, 359 lines checked
Improve the coding style so that it can now report:
total: 0 errors, 0 warnings, 6 checks, 360 lines checked
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
According to Server Base System Architecture (SBSA) specification,
the SBSA Generic Watchdog has two stage timeouts: the first signal
(WS0) is for alerting the system by interrupt, the second one (WS1) is a
real hardware reset.
More details about the hardware specification of this device:
ARM DEN0029B - Server Base System Architecture (SBSA)
This driver can operate ARM SBSA Generic Watchdog as a single stage
In the single stage mode, when the timeout is reached, your system
will be reset by WS1. The first signal (WS0) is ignored.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add Root Complex and Endpoint mode specific config entries, such that
it's feasible to enable the RC and/or EP mode driver indepently.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the PCIe EP mode support for lx2160a-v2 platform.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Modify the ls_pcie_dump_atu function, make it can print the INBOUND
windows registers.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the INBOUND configuration for VFs of PF.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Due to the ls2085a and ls2080a use different way to set the BAR size,
so add the BAR size init code here.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The VF_BARn_REG register's Prefetchable and Type bit fields
are overwritten by a write to VF's BAR Mask register.
workaround: Before writing to the VF_BARn_MASK_REG register,
write 0b to the PCIE_MISC_CONTROL_1_OFF register.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the multiple function support for Layerscape platform, some PEXs
of Layerscaple platform have more than one PF.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Some EP deivces need to initialize before RC scan it, e.g. NXP
layerscape platform, so add the init function in pci_ep uclass.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Split the RC and EP driver, and reimplement the EP driver base on
the EP framework.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Move i2c_early_init_f to common function
to initialize baudrate of i2c
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Register the random number generator with the rng subsystem in u-boot.
This way it can be used by EFI as well as for the 'rng' command.
Signed-off-by: Michael Walle <michael@walle.cc>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
If it is already instantiated tear it down first and then reinstanciate
it again with prediction resistance.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The secure keys (TDKEK, JDKEK, TDSK) can only be generated once after a
POR. Otherwise the RNG4 will throw an error.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Since Era 10, the version registers changed. Add the version registers
and use them on newer modules.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
We need the era in other modules, too. For example, to get the RNG
version.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Align the status line with all the other output in U-Boot.
Before the change:
DDR 3.9 GiB (DDR3, 32-bit, CL=11, ECC on)
SEC0: RNG instantiated
WDT: Started with servicing (60s timeout)
After the change:
DDR 3.9 GiB (DDR3, 32-bit, CL=11, ECC on)
SEC0: RNG instantiated
WDT: Started with servicing (60s timeout)
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The value 0 assigned to final is overwritten before ever being used.
Remove the assignment.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The sequence of arguments should match the format string.
For printing unsigned numbers we should use %u.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The eSDHC adapter card identification and multiplexing configuration
through FPGA had been implemented in both common mmc driver and
fsl_esdhc driver. However it is proper to move these code to board
files and do it during board initialization. The FPGA registers are
also board specific.
This patch is to move eSDHC adapter card identification and
multiplexing configuration from mmc driver to specific board files.
And the option CONFIG_FSL_ESDHC_ADAPTER_IDENT is no longer needed.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[Rebased, Removed T1040QDS change as board does not exist]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The sdhc_adapter of global data has not been used, and we
do not have to use it as global data even we may need it
in the future.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The correct setting for the RGMII ports on LS1012ARDB is to
enable delay on both Rx and Tx so the interface mode used should
be PHY_INTERFACE_MODE_RGMII_ID
Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Signed-off-by: Anji J <anji.jagarlmudi@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
On aarch64 running with dcache off, will result in an unaligned access
exception:
=> dcache off
=> hash sha1 $kernel_addr_r 100
"Synchronous Abort" handler, esr 0x96000061
elr: 00000000960317d8 lr : 00000000960316a4 (reloc)
elr: 00000000fbd787d8 lr : 00000000fbd786a4
[..]
The compiler emits a "stur x1, [x0, #12]". x1 is might just be 32 bit
aligned pointer. Remove the unused u64 element from the union to drop
the minimal alignment to 32 bit. Also remove the union, because it is
no more needed.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Current PFE firmware access spi-nor memory directly. New spi-mem
framework does not support direct memory access. So, let's use
spi_flash_read API to access memory instead of directly using it.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Communication with some SPI slaves just won't cut it if these delays
(before the beginning, and after the end of a transfer) are not added to
the Chip Select signal.
These are a straight copy from Linux:
Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt
drivers/spi/spi-fsl-dspi.c
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use the _ptr suffixed variant instead of casting. Also, convert it to
dev_read_addr_ptr(), which is safe to CONFIG_OF_LIVE.
One curious part is an error check like follows in
drivers/watchdog/omap_wdt.c:
priv->regs = (struct wd_timer *)devfdt_get_addr(dev);
if (!priv->regs)
return -EINVAL;
devfdt_get_addr() returns FDT_ADDR_T_NONE (i.e. -1) on error.
So, this code does not catch any error in DT parsing.
dev_read_addr_ptr() returns NULL on error, so this error check
will work.
I generated this commit by the following command:
$ find . -name .git -prune -o -name '*.[ch]' -type f -print | \
xargs sed -i -e 's/([^*)]*\*)devfdt_get_addr(/dev_read_addr_ptr(/'
I manually fixed drivers/usb/host/ehci-mx6.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add a sandbox SOC driver, and some tests for the SOC uclass.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Introduce UCLASS_SOC to be used for SOC identification and attribute
matching based on the SoC ID info. This allows drivers to be provided
for SoCs to retrieve SoC identifying information and also for matching
device attributes for selecting SoC specific data.
This is useful for other device drivers that may need different
parameters or quirks enabled depending on the specific device variant in
use.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
These functions should not modify the device. Convert them to const so
that callers don't need to cast if they have a const udevice *.
Signed-off-by: Simon Glass <sjg@chromium.org>
With all the changes in place, add support for DM into the
dc2114x driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Split the common code from the non-DM code, so it can be reused by
the DM code later. As always, the recv() function had to be split
into the actual receiving part and free_pkt part to fit with the
DM.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Split the RX data check from the rest of the RX function, so that
the check can be performed separately from the processing of the
packet and the release of the received packet once the processing
is finished.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
The RX/TX DMA descriptor rings are per-device-instance private data,
so move them into the private data.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
