Commit graph

688 commits

Author SHA1 Message Date
Dirk Eibach
b46226bdb5 i2c: IHS I2C master driver
IHS I2C master support was merely a hack in the osd driver.
Now it is a proper u-boot I2C framework driver, supporting the
v2.00 master features.

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
2014-07-07 19:47:18 -04:00
Tom Rini
6ee3d00d1d Merge branch 'master' of git://git.denx.de/u-boot-i2c 2014-07-07 10:10:52 -04:00
York Sun
2f78eae506 ARMv8/FSL_LSCH3: Add FSL_LSCH3 SoC
Freescale LayerScape with Chassis Generation 3 is a set of SoCs with
ARMv8 cores and 3rd generation of Chassis. We use different MMU setup
to support memory map and cache attribute for these SoCs. MMU and cache
are enabled very early to bootst performance, especially for early
development on emulators. After u-boot relocates to DDR, a new MMU
table with QBMan cache access is created in DDR. SMMU pagesize is set
in SMMU_sACR register. Both DDR3 and DDR4 are supported.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
2014-07-03 08:40:51 +02:00
Stephen Warren
ad3091ad03 i2c: tegra: dump alen in debug statements
Since tegra_i2c_{read,write}'s debug() call dumps the chip address, dump
the address length (alen) too, so the address value can be correctly
interpreted.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Yen Lin <yelin@nvidia.com>
2014-07-03 06:29:39 +02:00
Stephen Warren
981b14f01a i2c: tegra: write clean data to TX FIFO
The Tegra I2C controller's TX FIFO contains 32-bit words. If the final
FIFO entry of a transaction contains fewer than 4 bytes, the driver
currently fills the unused FIFO bytes with uninitialized data. This can
be confusing when reading back the FIFO content for debugging purposes.

Solve this by explicitly initializing the variable containing FIFO data
before filling it (partially) with data. With this change,
send_recv_packets()'s loop's if (is_write) code mirrors the else (i.e.
read) branch.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Yen Lin <yelin@nvidia.com>
2014-07-03 06:29:31 +02:00
Stephen Warren
68049a082b i2c: tegra: use repeated start for reads
I2C read transactions are typically implemented as follows:

START(write) address REPEATED_START(read) data... STOP

However, Tegra's I2C driver currently implements reads as follows:

START(write) address STOP START(read) data... STOP

This sequence confuses at least the AS3722 PMIC on the Jetson TK1 board,
leading to corrupted read data in some cases. Fix the driver to chain
the transactions together using repeated starts to solve this.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Yen Lin <yelin@nvidia.com>
2014-07-03 06:29:19 +02:00
Steve Rae
6736ec15c5 i2c: kona: Resolve Kona I2C driver issue
- "i2c mw" command hangs (with some compilers)

Signed-off-by: Steve Rae <srae@broadcom.com>
2014-06-12 11:42:50 +02:00
Hans de Goede
2072e72629 mvtwsi: Remove unnecessary twsi_baud_rate and twsi_slave_address globals
These are used only once, so their is no need to have them global.

This also stops mvtwsi from using any bss vars making it easier to use
before dram init (to talk to the pmic to set the dram voltage).

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-05-14 12:59:12 +02:00
Hans de Goede
fab356a0b8 mvtwsi: Fix clock programming
The TWSI_FREQUENCY macro was wrong in 2 ways:
1) It was casting the result of the calculations to an u8, while i2c clk
rates are often >= 100Khz which won't fit in a u8, drop the cast.
2) It had an extra factor of 2 in the divider which neither the datasheet nor
the Linux driver have.

The comment for the default value was wrongly saying that m lives in
bits 4-7, while in reality it is in bits 3-6, as can be seen from the correct
shift by 3 used in i2c_init().

While at it remove the unused twsi_actual_speed variable.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-05-14 12:58:55 +02:00
Tom Rini
bcb879c0e3 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-05-09 11:18:45 -04:00
Albert ARIBAUD
d2a3e91139 Merge branch 'u-boot/master'
Conflicts:
	drivers/net/Makefile

(trivial merge)
2014-05-09 11:50:14 +02:00
Jesper B. Christensen
5146fc2b37 i2c: zynq: Fixed compilation errors when using DEBUG
Signed-off-by: Jesper B. Christensen <jesper.christensen@cobham.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-08 07:03:37 +02:00
Shaveta Leekha
a405764c1e drivers/i2c/fsl_i2c: modify i2c_read to handle multi-byte write
Most of the I2C slaves support accesses in the typical style
that is : read/write series of bytes at particular address offset.
These transactions look like:"
(1) START:Address:Tx:Offset:RESTART:Address[0..4]:Tx/Rx:data[0..n]:STOP"

However there are certain devices which support accesses in
terms of the transactions as follows:
(2) "START:Address:Tx:Txdata[0..n1]:Clock_stretching:
        RESTART:Address:Rx:data[0..n2]"
Here Txdata is typically a command and some associated data,
similarly Rxdata could be command status plus some data received
as a response to the command sent.

Type (1) transactions are currently supportd in the
i2c driver using i2c_read and i2c_write APIs. I2C EEPROMs,
RTC, etc fall in this category.

To handle type (2) along with type (1) transactions,
i2c_read() function has been modified.

Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
2014-04-29 07:10:58 +02:00
York Sun
dec1861be9 driver/mxc_i2c: Move static data structure to global_data
This driver needs a data structure in SRAM before SDRAM is available.
This is not alway the case using .data section. Moving this data
structure to global_data guarantees it is writable.

Signed-off-by: York Sun <yorksun@freescale.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
2014-04-29 07:10:27 +02:00
Albert ARIBAUD
c9aab0f9dd Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-04-21 21:01:35 +02:00
Vitaly Andrianov
e8459dcc33 i2c, davinci: convert driver to new mutlibus/mutliadapter framework
- add davinci driver to new multibus/multiadpater support
    - adapted all config files, which uses this driver

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
2014-04-17 17:24:38 -04:00
Karicheri, Muralidharan
356d15ebb2 i2c, davinci: move i2c_defs.h to the drivers/i2c directory
This patch moves the davinci i2c_defs.h file to drivers.i2c directory.
It will allow to reuse the davinci_i2c driver for TI Keystone2 SOCs.

Not used "git mv" command to move the file because small part of
it with definitions specific for Davinci SOCs has to remain in the
arch/arm/include/asm/arch-davinci.

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Tom Rini <trini@ti.com>
2014-04-17 17:24:38 -04:00
Tetsuyuki Kobayashi
7a65768903 i2c: sh_i2c: bugfix: i2c probe command does not work
This is regression of commit 2035d77d i2c: sh_i2c: Update to new CONFIG_SYS_I2C framework

Before commit 2035d77d, i2c probe command works properly on kzm9g board.

KZM-A9-GT# i2c probe
Valid chip addresses: 0C 12 1D 32 39 3D 40 60

After commit 2035d77d, i2c probe command does not work.

KZM-A9-GT# i2c probe
Valid chip addresses: 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F 60 61 62 63 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 7F

sh_i2c_probe() calls sh_i2c_read(), but read length is 0. So acutally it does not read device at all. This patch prepares dummy buffer and read data into it.

Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-04-14 17:41:48 +09:00
Masahiro Yamada
462d1883f7 drivers: i2c: delete an unused source file
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Heiko Schocher <hs@denx.de>
2014-03-31 07:30:55 +02:00
Tom Rini
eeb72e6761 Merge branch 'master' of git://git.denx.de/u-boot-arm
Conflicts:
	arch/arm/cpu/armv7/config.mk
	board/ti/am43xx/mux.c
	include/configs/am43xx_evm.h

Signed-off-by: Tom Rini <trini@ti.com>
2014-02-26 16:49:58 -05:00
Darwin Rambo
4bded3a367 i2c: kona: Add Kona I2C driver
Add support for the Kona I2C controller found on Broadcom mobile SoCs.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>
2014-02-22 19:30:39 +01:00
Tom Rini
6853e6aa77 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-02-20 12:18:59 -05:00
Alexey Brodkin
3d93f6959b designware_i2c: remove inclusion of <asm/arch/hardware.h>
As soon as all boards have their CONFIG_SYS_I2C_BASE defined in
configuration files instead of "asm/arch/hardware.h" it's safe to remove
the inclusion in question and make driver platform-independent.

Cc: Tom Rini <trini@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Armando Visconti <armando.visconti@st.com>

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2014-02-20 06:49:09 +01:00
Hannes Petermaier
d5243359e1 OMAP24xx I2C: Add support for set-speed
Adds support for set-speed on the OMAP24xx I2C Adapter.

Changes to omap24_i2c_write(...) for polling ARDY Bit from IRQ-Status.
Otherwise on a subsequent call the transfer of last byte from the
predecessor is aborted and therefore lost. For exmaple when
i2c_write(...) is followed by a i2c_setspeed(...) (which has to
deactivate and activate master for changing psc,...).

Minor cosmetical changes.

Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Cc: Heiko Schocher <hs@denx.de>
2014-02-20 06:48:23 +01:00
Marek Vasut
d22643e7e8 i2c: i2c-mxs: Wait for I2C to empty queue
Make sure the I2C write queue is empty before leaving the mxs_i2c_write().
If we start and I2C write and only wait for ACK, the MXS I2C IP block may
enter next operation while still processing the write aftermath internally.
This will in turn disrupt one or more subsequent transfer(s).

A testcase for this issue is as such. This testcase is also interesting because
the first I2C_WRITE which becomes disruptive happens in the 'i2c read' command.
The 'i2c read' command first uses I2C_WRITE to send I2C address of the chip and
then uses I2C_READ to read data from the chip. After this command completes, the
'i2c probe' will use sequence of I2C_WRITE commands to probe the I2C bus. The
problem is that the first I2C_WRITE disrupted the I2C IP block operation and
this sideeffect propagates all the way to this next I2C_WRITE used by the 'i2c
probe' call. The result is the 'i2c probe' receives an ACK on I2C address 0x00,
even if this ACK was owned by the previous I2C_WRITE operation. Note that the
'i2c read' command must read from a valid I2C chip address.

Wrong:
> i2c probe
Valid chip addresses: 50 51
> i2c read 0x50 0x0.2 0x10 0x42000000
> i2c probe
Valid chip addresses: 00 50 51

With this patch
> i2c probe
Valid chip addresses: 50 51
> i2c read 0x50 0x0.2 0x10 0x42000000
> i2c probe
Valid chip addresses: 50 51

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
2014-02-20 06:46:57 +01:00
Chin Liang See
070cbaf821 designware_i2c: Enhance DesignWare I2C driver address support
Enhance the DesignWare I2C driver to support address length more
than 1 byte. This enhancement is required as some I2C slave
device such as EEPROM chip might have 16 bit address byte.

Signed-off-by: Chin Liang See <clsee@altera.com>
Acked-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Cc: Tom Rini <trini@ti.com>
cc: Armando Visconti <armando.visconti@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
2014-02-20 06:46:56 +01:00
Scott Jiang
16c550274c blackfin: make i2c driver blackfin independant
The ADI twi peripheral is not binding to Blackfin processor only.
Access i2c registers by standard io functions.
Fix coding style.

Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2014-02-20 06:46:56 +01:00
Sonic Zhang
86bdd70a09 blackfin: rename bfin-twi_i2c driver to adi_i2c
The ADI twi peripheral is not binding to Blackfin processor only.
Change to a generic name.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2014-02-20 06:46:56 +01:00
Sonic Zhang
d6a320d5bb blackfin: add spi and i2c specific get clock functions
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2014-02-20 06:46:56 +01:00
Sonic Zhang
bb0fad0ea0 blackfin: the sclk MHz in i2c driver should be divided by 1000 other than 1024
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2014-02-20 06:46:55 +01:00
Michael Burr
18948632a9 i2c: zynq: Add support for the second i2c controller
Initialize the second i2c controller.

Signed-off-by: Michael Burr <michael.burr@logicpd.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-20 06:46:55 +01:00
Michael Burr
9e90107155 i2c: zynq: Support for 0-length register address
Fixed bug with alen == 0 in 'i2c_write', 'i2c_read'
Further minor corrections:
- Write 'address' register before 'data' register.
- Write 'transfer_size' register before 'address' register.

Signed-off-by: Michael Burr <michael.burr@logicpd.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-20 06:46:55 +01:00
Marek Vasut
c8d4b2f826 ARM: IXP: Remove the IXP architecture support
The architecture is unmaintained and dead, remove it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>
2014-02-06 02:51:52 +01:00
Kuo-Jung Su
dccacbe019 i2c: fti2c010: fix compiler warning on paddr[]
This fixes the following compiler warnings:

fti2c010.c: In function 'fti2c010_read':
fti2c010.c:204:8: warning: 'paddr' may be used uninitialized in this function [-Wuninitialized]
fti2c010.c: In function 'fti2c010_write':
fti2c010.c:266:8: warning: 'paddr' may be used uninitialized in this function [-Wuninitialized]

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Cc: Heiko Schocher <hs@denx.de>
2014-01-13 08:18:38 +01:00
Alexey Brodkin
32d041e218 drivers/designware_i2c - add suppor of CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
Since we agreed on legacy implementation of "eeprom_{read|write}"
(http://patchwork.ozlabs.org/patch/295825/) I had to fix/make it work
again DesignWare I2C driver for cases when 1 EEPROM IC fake I2C with
anumber of "built-in" ICs with different chip addresses.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

Cc: Tom Rini <trini@ti.com>
cc: Armando Visconti <armando.visconti@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Vipin KUMAR <vipin.kumar@st.com>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Kuo-Jung Su <dantesu@faraday-tech.com>
2014-01-13 08:18:13 +01:00
Darwin Rambo
7cc1b02f8f i2c: Fix i2c speed command
This corrects i2c core to interpret the value returned by
i2c_set_bus_speed as a success indicator rather than the
actual speed that was set. When i2c_set_bus_speed returns
a failure code, the speed is unknown so the adapter speed
is set to zero.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Steve Rae <srae@broadcom.com>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2014-01-13 08:17:51 +01:00
Nobuhiro Iwamatsu
da1ed0d20e rcar_i2c: Clear status before start master receive
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-01-13 08:16:48 +01:00
Hisashi Nakamura
ad5e14ecdd rcar_i2c: Fix receiving wait condition
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-01-13 08:16:22 +01:00
Alban Bedel
ac2ff538cd i2c: tegra: Add the fifth bus on SoC with more than 4 buses
Create the i2c adapter object for the fifth bus on SoC with more than
4 buses. This allow using all the bus available on T30.

Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-12-18 10:19:49 -07:00
Tom Rini
4b210ad342 Merge branch 'master' of git://git.denx.de/u-boot-arm
Conflicts:
	board/samsung/trats2/trats2.c
	include/configs/exynos5250-dt.h

Signed-off-by: Tom Rini <trini@ti.com>
2013-12-10 17:15:18 -05:00
Albert ARIBAUD
f15ea6e1d6 Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	arch/arm/cpu/armv7/rmobile/Makefile
	doc/README.scrapyard

Needed manual fix:
	arch/arm/cpu/armv7/omap-common/Makefile
	board/compulab/cm_t335/u-boot.lds
2013-12-10 22:23:59 +01:00
Naveen Krishna Ch
e717fc6d1a i2c: samsung: register i2c busses for Exynso5420 and Exynos5250
This patch adds the U_BOOT_I2C_ADAP_COMPLETE defines for channels
on Exynos5420 and Exynos5250 and also adds support for init function
for hsi2c channels

Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
2013-12-06 07:46:23 +01:00
Nikita Kiryanov
92c23c9226 arm: omap: i2c: don't zero cnt in i2c_write
Writing zero into I2Ci.I2C_CNT register causes random I2C failures in OMAP3
based devices. This seems to be related to the following advisory which
apears in multiple erratas for OMAP3 SoCs (OMAP35xx, DM37xx), as well as
OMAP4430 TRM:

Advisory:
I2C Module Does Not Allow 0-Byte Data Requests
Details:
When configured as the master, the I2C module does not allow 0-byte data
transfers. Note: Programming I2Ci.I2C_CNT[15:0]: DCOUNT = 0 will cause
undefined behavior.
Workaround(s):
No workaround. Do not use 0-byte data requests.

The writes in question are unnecessary from a functional point of view.
Most of them are done after I/O has finished, and the only one that preceds
I/O (in i2c_probe()) is also unnecessary because a stop bit is sent before
actual data transmission takes place.

Therefore, remove all writes that zero the cnt register.

Cc: Heiko Schocher <hs@denx.de>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Tom Rini <trini@ti.com>
Cc: Lubomir Popov <lpopov@mm-sol.com>
Cc: Enric Balletbo Serra <eballetbo@gmail.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
2013-12-05 12:25:02 +01:00
Kuo-Jung Su
c727618d2c i2c: fti2c010: serial out r/w address in MSB order
For a eeprom with a 2-bytes address (e.g., Ateml AT24C1024B),
the r/w address should be serial out in MSB order.

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Cc: Heiko Schocher <hs@denx.de>
2013-12-05 12:25:01 +01:00
Kuo-Jung Su
49f4c762e4 i2c: fti2c010: migrate to new i2c model
Replace the legacy i2c model with the new one.

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Cc: Heiko Schocher <hs@denx.de>
2013-12-05 12:25:01 +01:00
Kuo-Jung Su
e6d3ab8909 i2c: fti2c010: cosmetic: coding style cleanup
Coding style cleanup

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Cc: Heiko Schocher <hs@denx.de>
2013-12-05 12:25:00 +01:00
Piotr Wilczek
a6756bbdac driver:i2c:s3c24x0: fix clock init for hsi2c
Fix clock value initialisation for Exynos other than Exynos5 for hsi2c.

Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
2013-12-05 07:39:38 +01:00
Piotr Wilczek
2d8f1e2769 driver:i2c:s3c24x0: adapt driver to new i2c
This patch adapts the s3c24x0 driver to the new i2c framework.
Config file is modified for all the boards that use the driver.

Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
CC: Heiko Schocher <hs@denx.de>
CC: Inderpal Singh <inderpal.singh@linaro.org>
CC: David Müller <d.mueller@elsoft.ch>
CC: Chander Kashyap <k.chander@samsung.com>
CC: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
2013-12-05 07:39:38 +01:00
Andreas Bießmann
cb96a0a4c9 i2c: switch from AT91 legacy to ATMEL legacy
Since the required API is gpio which is enclosed with CONFIG_ATMEL_LEGACY use
that switch here.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Heiko Schocher <hs@denx.de>
2013-11-13 22:13:22 +01:00
Alexey Brodkin
f9de54e9b0 designware_i2c: remove 10msec delay in i2c_xfer_finish
This delay applies to any data transfer on I2C bus.

For example 1kB data read with per-byte access (which happens if
environment is stored in I2C EEPROM) takes more than 10 seconds.

Moreover data bus driver has to care about bus state and data transfer,
but not about internal states of attached devices.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

Cc: Tom Rini <trini@ti.com>
cc: Armando Visconti <armando.visconti@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Vipin KUMAR <vipin.kumar@st.com>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
2013-11-13 06:22:41 +01:00
Alexey Brodkin
8b7c872539 designware_i2c: disable i2c controller during target address setup
As it is stated in DesignWare I2C databook: writes to IC_TAR (0x4)
register succeed only when IC_ENABLE[0] is set to 0.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

Cc: Tom Rini <trini@ti.com>
cc: Armando Visconti <armando.visconti@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Vipin KUMAR <vipin.kumar@st.com>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
2013-11-13 06:22:06 +01:00
Heiko Schocher
85bb251b39 i2c, omap1510: remove i2c driver
remove omap1510 i2c driver, as there is no board which uses it

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Jian Zhang <jzhang@ti.com>
2013-11-13 06:18:31 +01:00
Heiko Schocher
0bdffe71fd i2c, zynq: convert zynq i2c driver to new multibus/multiadapter framework
- add zync i2c driver to new multibus/multiadpater support
- adapted all config files, which uses this driver

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Michal Simek <michal.simek@xilinx.com>
2013-11-13 06:18:27 +01:00
Heiko Schocher
6789e84eca i2c, omap24xx: convert driver to new mutlibus/mutliadapter framework
- add omap24xx driver to new multibus/multiadpater support
- adapted all config files, which uses this driver

Tested on the am335x based siemens boards rut, dxr2 and pxm2
posted here:
http://patchwork.ozlabs.org/patch/263211/

Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Tom Rini <trini@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Nagendra T S  <nagendra@mistralsolutions.com>
Cc: Michael Jones <michael.jones@matrix-vision.de>
Cc: Raphael Assenat <raph@8d.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stefano Babic <sbabic@denx.de>
2013-11-13 06:18:17 +01:00
Marek Vasut
124913556c i2c: mxs_i2c: Squash endless loop
The endless waiting for a bit to be set can cause a hang, add a timeout
so we prevent such situation. A testcase for such a hang is below. The
testcase assumes a device to be present at address 0x50 and a device to
NOT be present at address 0x42 . Also note that the "sleep 1" induced
delays are imperative for this bug to manifest .

i2c read 0x42 0x0.2 0x10 0x42000000 ; sleep 1 ; \
i2c read 0x50 0x0.2 0x10 0x42000000 ; sleep 1 ; \
i2c read 0x42 0x0.2 0x10 0x42000000

The expected result of the above command is:

Error reading the chip.
Error reading the chip.

While without this patch, we observe a hang in the last read from 0x42
precisely when waiting for this bit to be set.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2013-11-13 06:08:31 +01:00
Nobuhiro Iwamatsu
2035d77d79 i2c: sh_i2c: Update to new CONFIG_SYS_I2C framework
This updates to new I2C framwwork on sh_i2c.
And this also updates boards(kzm9g and ecovec) that using sh_i2c.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2013-11-13 06:08:26 +01:00
Masahiro Yamada
710f1d3d5f drivers: convert makefiles to Kbuild style
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31 13:26:01 -04:00
Masahiro Yamada
9a2a73d29f i2c: eliminate warnings in i2c_reloc_fixup function
The prototype of handlers had changed.
This commit uses cast with (void *) rather than
the handler-specific prototype.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-17 07:24:41 +02:00
Naveen Krishna Ch
296a461dca i2c: s3c24xx: add hsi2c controller support
Add support for hsi2c controller available on exynos5420.

Note: driver currently supports only fast speed mode 100kbps

Change-Id: I02555b1dc8f4ac21c50aa5158179768563c92f43
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: R. Chandrasekar <rc.sekar@samsung.com>
2013-10-17 07:20:26 +02:00
Simon Glass
940dd16242 exynos: i2c: Change FDT bus setup code to enumerate ports correctly
At present the i2c ports are enumerated in a strange way - the
fdtdec_find_aliases_for_id() function is used, but then the ID returned
is ignored and the ports are renumbered. The effect is the same provided
that the device tree has the ports in the same order, or uses aliases,
and has no gaps, but it is not correct.

Adjust the code to use the function as intended. This will allows device
tree aliases to change the device order if required.

As a result, the i2c_busses variable is dropped. We can't be sure that
there are no 'holes' in the list of buses, so must check the whole
array.

Note: it seems that non-FDT operation is now broken in this drive and
will need to be reinstated for upstream.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59369
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
2013-10-17 07:20:26 +02:00
Naveen Krishna Ch
e4e2402071 exynos: i2c: Fix i2c driver to handle NACKs properly
The Exynos5 i2c driver does not handle NACKs properly. This change:

- fixes the NACK processing problem (do not continue transaction if
  address cycle was NACKed)

- eliminates a fair amount of duplicate code

Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-by: Simon Glass <sjg@google.com>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
2013-10-17 07:20:26 +02:00
Jens Scharsig (BuS Elektronik)
83d271b5ff Fix: nommu I2C adapter relocation error
NoMMU systems have a access violation problem with i2c_reloc_fixup.
Blame for it is a double relocation of the adapter itself. The
i2c_adap_p is already relocated, if i2c_reloc_fixup is called.
This patch removes the relocation of i2c_adap_p from i2c_reloc_fixup
to fix this.

Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
2013-10-17 07:20:25 +02:00
Nobuhiro Iwamatsu
b55b8eef35 i2c: sh_i2c: Avoid using I2C prior to relocation
If user uses the I2C in before the relocation, board of sh and rmobile
will not start. This will solve this problem.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2013-10-17 07:20:25 +02:00
Heiko Schocher
13c2433ccb i2c, core: optimze i2c_set_bus_num()
check first, if we are on the bus, we want to enable. If so,
return immediately, do not calc max adapter number, nor check
other things.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
2013-10-17 07:20:25 +02:00
Nobuhiro Iwamatsu
1086bfa9f4 i2c: Add support for Renesas rcar
This supports i2c controller for Renesas rcar.

Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2013-10-17 07:20:25 +02:00
Michael Burr
e66587495d i2c: Zynq: Support for TI PCA9548 bus multiplexer
(Interface is not quite the same as Phillips PCA9547.)

Signed-off-by: Michael Burr <michael.burr@logicpd.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Michal Simek <monstr@monstr.eu>
2013-10-17 07:20:25 +02:00
trem
fac9640895 i2c: mxc: move to new subsystem
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
2013-10-17 07:20:24 +02:00
Masahiro Yamada
a341f649d7 drivers: s3c44b0_i2c: delete an unused driver
Since commit 5dc5f36 removed B2 board support,
there are no boards enabling s3c44b0_i2c.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Andrea Scian <andrea.scian@dave-tech.it>
Acked-by: Heiko Schocher <hs@denx.de>
2013-09-19 09:51:52 +02:00
Chunhe Lan
9c3f77eb3b fsl_i2c: add workaround for the erratum I2C A004447
This workaround is for the erratum I2C A004447. Device reference
manual provides a scheme that allows the I2C master controller
to generate nine SCL pulses, which enable an I2C slave device
that held SDA low to release SDA. However, due to this erratum,
this scheme no longer works. In addition, when I2C is used as
a source of the PBL, the state machine is not able to recover.

At the same time, delete the reduplicative definition of SVR_VER
and SVR_REV. The SVR_REV is the low 8 bits rather than the low 16
bits of svr. And we use the CONFIG_SYS_FSL_A004447_SVR_REV macro
instead of hard-code value 0x10, 0x11 and 0x20.

The CONFIG_SYS_FSL_A004447_SVR_REV = 0x00 represents that one
version of platform has this I2C errata. So enable this errata
by IS_SVR_REV(svr, maj, min) function.

Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
2013-08-20 11:15:31 +02:00
Chunhe Lan
b8ce3343b6 fsl_i2c: generate nine pulses on SCL if the I2C bus is hung
When the code detected that the bus is hung (e.g. SDA stuck low),
send 9 pulses on SCL to try to fixup the bus.

Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
2013-08-20 11:15:31 +02:00
Simon Glass
cdce889959 tegra: Avoid using I2C prior to relocation
Tegra recently moved to the new I2C framework, which sets up I2C prior to
relocation, and prior to calling i2c_init_board(). This causes a crash on
Tegra boards.

Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
2013-08-13 17:11:25 -04:00
Marek Vasut
90f002a90f i2c: soft: Fix typo in CONFIG_SYS_I2C_SOFT_SPEED
In case only the CONFIG_SYS_I2C_SPEED is set in configuration file,
the CONFIG_SYS_I2C_SOFT_SPEED is defined as CONFIG_SYS_I2C_SPEED.
The CONFIG_SYS_I2C_SOFT_SPEED is then used throughout the driver.

Unfortunatelly, due to a typo in the driver, instead of defining
CONFIG_SYS_I2C_SOFT_SPEED, an CONFIG_SYS_SOFT_I2C_SPEED was defined
and therefore the driver failed to compile. The same applies for
CONFIG_SYS_I2C_SOFT_SLAVE , where the swap happens as well.

This patch fixes the issue.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
2013-08-03 06:01:18 +02:00
Tom Rini
8dde4ca90e drivers/i2c: Update fti2c010.[ch], i2c_core.c to use SPDX identifiers
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-25 08:51:42 -04:00
Tom Rini
c2120fbfbc Merge branch 'master' of git://git.denx.de/u-boot-i2c
The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.

Conflicts:
	board/sandburst/common/ppc440gx_i2c.c
	board/sandburst/common/ppc440gx_i2c.h

Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:50:24 -04:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Kuo-Jung Su
3cff842bca i2c: add Faraday FTI2C010 I2C controller support
Faraday FTI2C010 is a multi-function I2C controller
which supports both master and slave mode.
This patch simplily implements the master mode only.

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Heiko Schocher <hs@denx.de>
2013-07-23 08:34:58 +02:00
Alison Wang
30ea41a489 I2C: mxc_i2c: Add support for Vybrid VF610 platform
This patch adds support for Vybrid VF610 platform.

There are some differences between i.MX6 and Vybrid for I2C controller.
(1) The registers' offset are different.
(2) The I2C clock divider values are different.
(3) In I2C control register, the enable/disable/reset bit is inverted for Vybrid comparing to i.MX6.
(4) In I2C status register, the interrupt flag bit is cleared by writing "1" for Vybrid.
For i.MX6, this bit is cleared by writing "0".
(5) In I2C status register, the arbitration lost flag bit is cleared by writing "1" for Vybrid.
For i.MX6, this bit is cleared by writing "0".

Signed-off-by: Alison Wang <b18965@freescale.com>
2013-07-23 08:34:57 +02:00
Dirk Eibach
880540decf i2c, ppc4xx_i2c: switch to new multibus/multiadapter support
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
2013-07-23 08:34:56 +02:00
Simon Glass
1f2ba722ac tegra: i2c: Enable new CONFIG_SYS_I2C framework
This enables CONFIG_SYS_I2C on Tegra, updating existing boards and the Tegra
i2c driver to support this.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heiko Schocher <hs@denx.de>
2013-07-23 08:34:55 +02:00
Simon Glass
d84eb856c4 tegra: i2c: Add function to know about current bus
Rather than using a variable in various places, add a single function,
tegra_i2c_get_bus(), which returns a pointer to information about a
bus.

This will make it easier to move to the new i2c framework.

Signed-off-by: Simon Glass <sjg@chromium.org>
2013-07-23 08:34:54 +02:00
Heiko Schocher
00f792e0df i2c, fsl_i2c: switch to new multibus/multiadapter support
- added to fsl_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
2013-07-23 08:34:53 +02:00
Heiko Schocher
ea818dbbcd i2c, soft-i2c: switch to new multibus/multiadapter support
- added to soft_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
2013-07-23 05:54:29 +02:00
Heiko Schocher
385c9ef5a7 i2c: add i2c_core and prepare for new multibus support
This Patch introduce the new i2c_core file, which holds
the I2C core functions, for the rework of the multibus/
multiadapter support.
Also adds changes in i2c.h for the new I2C multibus/multiadapter
support. This new support can be activated with the
CONFIG_SYS_I2C define.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
2013-07-23 05:54:28 +02:00
Reinhard Pfau
b778c1b5de i2c: fsl_i2c: i2c_read(): dont try to write address w/ alen=0
if alen is 0: no longer start a write cycle before reading data.

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Reinhard Pfau <reinhard.pfau@gdsys.cc>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-07-16 17:44:30 -05:00
Amar
1ae76d438b EXYNOS: Resolve the i2c compilation error
This patch resolves the below mentioned compilation error of i2c driver
for non-FDT case

Compilation error:
s3c24x0_i2c.c: In function 'board_i2c_init':
s3c24x0_i2c.c:544:18: error: 'CONFIG_MAX_I2C_NUM' undeclared (first use
in this function) s3c24x0_i2c.c:544:18: note: each undeclared
identifier is reported only once for each function it appears in
s3c24x0_i2c.c:545:3: warning: implicit declaration of function

Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-07-10 14:20:26 +09:00
Amar
2c07bb9b53 EXYNOS5: I2C: Add FDT and non-FDT support for I2C
This patch updates the function board_i2c_init() to add support for both
FDT and non-FDT for I2C, and initialise the I2C channels.

Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-24 11:25:19 +09:00
Lubomir Popov
960187ffa1 ARM: OMAP: I2C: New read, write and probe functions
New i2c_read, i2c_write and i2c_probe functions, tested on OMAP4
(4430/60/70), OMAP5 (5430) and AM335X (3359); should work on older
OMAPs and derivatives as well. The only anticipated exception would
be the OMAP2420, which shall require driver modification.
- Rewritten i2c_read to operate correctly with all types of chips
  (old function could not read consistent data from some I2C slaves).
- Optimised i2c_write.
- New i2c_probe, performs write access vs read. The old probe could
  hang the system under certain conditions (e.g. unconfigured pads).
- The read/write/probe functions try to identify unconfigured bus.
- Status functions now read irqstatus_raw as per TRM guidelines
  (except for OMAP243X and OMAP34XX).
- Driver now supports up to I2C5 (OMAP5).

Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Heiko Schocher <hs@denx.de>
2013-06-10 08:43:26 -04:00
Michal Simek
8934f78465 i2c: zynq: Add support for Xilinx Zynq
Support Xilinx Zynq i2c controller.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@ti.com>
2013-04-30 11:39:28 +02:00
Tom Rini
0ce033d258 Merge branch 'master' of git://git.denx.de/u-boot-arm
Albert's rework of the linker scripts conflicted with Simon's making
everyone use __bss_end.  We also had a minor conflict over
README.scrapyard being added to in mainline and enhanced in
u-boot-arm/master with proper formatting.

Conflicts:
	arch/arm/cpu/ixp/u-boot.lds
	arch/arm/cpu/u-boot.lds
	arch/arm/lib/Makefile
	board/actux1/u-boot.lds
	board/actux2/u-boot.lds
	board/actux3/u-boot.lds
	board/dvlhost/u-boot.lds
	board/freescale/mx31ads/u-boot.lds
	doc/README.scrapyard
	include/configs/tegra-common.h

Build tested for all of ARM and run-time tested on am335x_evm.

Signed-off-by: Tom Rini <trini@ti.com>
2013-03-18 14:37:18 -04:00
Tom Warren
e32624ef82 Tegra: I2C: Add T114 clock support to tegra_i2c driver
T114 has a slightly different I2C clock, with a new (extra) divisor
in standard/fast mode and HS mode. Tested on my Dalmore, and the I2C
clock is 100KHz +/- 3Hz on my Saleae Logic analyzer.

Added a new entry in compat_names for T114 I2C since it differs
from the previous Tegra SoCs. A flag is set when T114 I2C HW is
found so new features like the extra clock divisor can be used.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
2013-03-14 11:06:41 -07:00
Rajeshwari Shinde
cb466c056a I2C: S3C24X0: Bug fixes in i2c_transfer
This patch corrects the following issues

1) Write the correct M/T Stop value to I2CSTAT after i2c write.
   According to the spec, after finish the data transmission, we should
   write a M/T Stop (I2C_MODE_MT | I2C_TXRX_ENA) to I2CSTAT instead of
   a M/R Stop (I2C_MODE_MR | I2C_TXRX_ENA).
2) Not split the write to I2CSTAT into 2 steps in i2c read.
   According to the spec, we should write the combined M/R Start value to
   I2CSTAT after setting the slave address to I2CDS
3) Fix the mistake of making an equality check to an assignment.
   In the case of I2C write with the zero-length address, while tranfering the
   data, it should be an equality check (==) instead of an assignment (=).

Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
2013-03-12 19:33:11 +01:00
Rajeshwari Shinde
cecf3c006f I2C: S3C24X0: Remove the dead code
This revomes the code under #if 0 in the s3c24x0_i2c driver.

Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
2013-03-12 19:32:41 +01:00
Simon Glass
609e6ec3f6 ppc: m68k: Move i2c1_clk, i2c2_clk to arch_global_data
Move these fields into arch_global_data and tidy up. This is needed for
both ppc and m68k since they share the i2c driver.

Signed-off-by: Simon Glass <sjg@chromium.org>
2013-02-04 09:05:42 -05:00
Marek Vasut
49c28b564b i2c: mxs: Staticize the functions in the driver
The local functions in the mxs i2c driver are not marked static, make it so.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
2013-01-29 06:39:52 +01:00
Albert ARIBAUD
1199c377cf Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master' 2013-01-14 15:21:00 +01:00
Rajeshwari Shinde
d04df3c6ad I2C: S3C24X0: Resolve build error for VCMA9
This patch resolves the following build errors for I2C driver in
VCMA9:

In file included from s3c24x0_i2c.c:40:0:
s3c24x0_i2c.h:38:17: error: field 'id' has incomplete type
s3c24x0_i2c.c:70:39: error: 'CONFIG_MAX_I2C_NUM' undeclared here (not
in a function) s3c24x0_i2c.c:70:31: warning: 'i2c_bus' defined but
not used [-Wunused-variable] s3c24x0_i2c.c:72:12: warning:
'i2c_busses' defined but not used [-Wunused-variable]

Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-01-14 14:45:30 +09:00
Albert ARIBAUD
79f3877794 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'
This required manual merging drivers/mtd/nand/Makefile
and adding am335x_evm support for CONFIG_SPL_NAND_DRIVERS
2013-01-08 13:15:45 +01:00
Rajeshwari Shinde
a9d2ae7014 I2C: Driver changes for FDT support
Functions added to get the I2C bus number and reset I2C bus using
FDT node.

Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-01-08 10:54:33 +09:00
Armando Visconti
d40d914c06 designware_i2c.h: Define IC_CLK only if not already defined in config file
Signed-off-by: Armando Visconti <armando.visconti@st.com>
2012-12-11 13:17:32 -07:00
Armando Visconti
ea31b7a7be designware_i2c.h: Fixed the correct values for SCL low/high time
Signed-off-by: Armando Visconti <armando.visconti@st.com>
2012-12-11 13:17:32 -07:00
Armando Visconti
5b8439bbde designware_i2c: Fixed the setting of the i2c bus speed
There are three couple (hcnt/lcnt) of registers for each
speed (SS/FS/HS). The driver needs to set the proper couple
of regs according to what speed we are setting.

Signed-off-by: Armando Visconti <armando.visconti@st.com>
2012-12-11 13:17:32 -07:00
Armando Visconti
491739bb74 designware_i2c: Added s/w generation of stop bit
In the newer versions of designware i2c IP there is the possibility
of configuring it with IC_EMPTYFIFO_HOLD_MASTER_EN=1, which basically
requires the s/w to generate the stop bit condition directly, as
the h/w will not automatically generate it when TX_FIFO is empty.

To avoid generation of an extra 0x0 byte sent as data, the
IC_STOP command must be sent along with the last IC_CMD.

This patch always writes bit[9] of ic_data_cmd even in the
older versions, assuming that it is a noop there.

Signed-off-by: Armando Visconti <armando.visconti@st.com>
2012-12-11 13:17:32 -07:00
Armando Visconti
ac6e2fe6e4 designware_i2c.c: Added the support for MULTI_BUS
This patch adds the capability to switch between 10
different I2C busses (from 0 to 9).

Signed-off-by: Armando Visconti <armando.visconti@st.com>
2012-12-11 13:17:31 -07:00
Piotr Wilczek
c86d9ed382 drivers:i2c: Modify I2C driver for Exynos4
This patch modifies the S3C i2c driver to support both Exynos4 and Exynos5

Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
2012-12-11 13:17:31 -07:00
Vincent Stehlé
66839773a8 omap24xx_i2c: Handle OMAP5 like OMAP2,3,4
OMAP5 has 8b i2c data register field, like OMAP2, 3 and 4. Handle in the same
way. This fixes the following error on OMAP5:

  OMAP5430 EVM # mmc rescan
  timed out in wait_for_bb: I2C_STAT=1410
  twl6035: could not turn on LDO9.

Signed-off-by: Vincent Stehlé <v-stehle@ti.com>
2012-12-11 13:17:31 -07:00
Marek Vasut
fa5e2845a8 mxs: i2c: Implement algorithm to set up arbitrary i2c speed
This algorithm computes the values of TIMING{0,1,2} registers for the
MX28 I2C block. This algorithm was derived by using a scope, but the
result seems correct.

The resulting values programmed into the registers do not correlate
with the contents in datasheet. When using the values from the datasheet,
the I2C clock were completely wrong.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
2012-12-11 13:17:30 -07:00
Marek Vasut
1e2fc0d19b mxs: i2c: Restore speed setting after block reset
The I2C block reset configures the I2C bus speed to strange value.
Read the I2C speed from the block before reseting the block and
restore it afterwards, so the I2C operates correctly. This issue
can be replicated by doing unsuccessful I2C transfer, after such
transfer finishes, the I2C block clock speed is misconfigured.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-12-11 13:17:30 -07:00
Marek Vasut
aff36ea92e i2c: mxs: Fix TIMING2 register value
According to FSL, the value in the TIMING2 register shall be 0x00300030
instead of what's written in the datasheet. This new value correlates
with older STMP36xx datasheet. Issues were detected in Linux when this
register was misconfigured, so write this correct value.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-12-11 13:17:30 -07:00
Marek Vasut
a157e0d5f6 i2c: mxs: Use i2c_set_bus_speed() in i2c_init()
Use i2c_set_bus_speed() in i2c_init() within the mxs i2c driver
to avoid duplication of code.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-12-11 13:17:30 -07:00
Marek Vasut
a06f590f7f i2c: mxs: Implement i2c_get/set_bus_speed()
This patch implements the setup and retrieval functions for the I2C
bus speed on the MXS I2C IP.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-12-11 13:17:30 -07:00
Marek Vasut
f32a470ed3 i2c: mxs: Abstract out the MXS I2C speed setup
This patch pulls out the I2C speed setup from the i2c_init() call
and implements the bus configuration lookup table with register
values that needs to be programmed into the I2C IP to run at
particular speed.

This patch is a first step towards implementing run-time I2C bus
speed configuration for the MXS I2C IP.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-12-11 13:17:30 -07:00
Marek Vasut
7f86bd576f i2c: Staticize local functions in mxc i2c driver
Some functions in the MXC i2c driver were not static, fix this by
making them so.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2012-12-11 13:17:29 -07:00
Andreas Bießmann
eabd5d8d70 soft_i2c: add necessary includes for AVR32
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
2012-12-11 13:17:29 -07:00
Vincent Stehlé
febc4cd48a omap24xx_i2c: Handle wait_for_bb error
We add a return code to wait_for_bb() to be able to report errors to the
callers properly. We in turn handle this new error code in i2c_read, i2c_write
and i2c_probe.

Signed-off-by: Vincent Stehlé <v-stehle@ti.com>
2012-12-10 12:45:35 -07:00
Tom Rini
5bb3505fa8 Merge branch 'master' of git://git.denx.de/u-boot-arm 2012-10-26 15:44:31 -07:00
Marek Vasut
6f62f42071 arm: Remove support for lpc2292
This stuff has been rotting in the tree for a year now. Remove it.

Signed-off-by: Marek Vasut <marex@denx.de>
2012-10-26 22:35:20 +02:00
Kim Phillips
62f730fffd drivers/i2c/fsl_i2c.c: sparse fix
fsl_i2c.c:217:14: warning: symbol 'get_i2c_clock' was not declared. Should it be static?

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Heiko Schocher <hs@denx.de>
2012-10-25 12:06:21 -07:00
Tetsuyuki Kobayashi
f539094f48 i2c: sh_i2c: use setbits/clrbits macro
Use setbits/clrbits macro when read-modify-write register.

Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2012-10-16 05:47:21 +02:00
Tetsuyuki Kobayashi
0e5fb33cf7 i2c: sh_i2c.c: check error in i2c_read and i2c_write
Before this patch, i2c_{read,write} always returned 0.
Check TACK in i2c_raw_{read,write} so that i2c_{read,write} return non-zero when error.

Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
2012-10-16 05:47:20 +02:00
Tetsuyuki Kobayashi
d042d7121b i2c: sh_i2c: enable i2c_probe
Before this patch i2c_probe() always returned 0 and "i2c probe" command did not work properly.

Modify i2c_set_addr() to check TACK when waiting DTE and make i2c_probe() call this function.

Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
2012-10-16 05:47:20 +02:00
Tetsuyuki Kobayashi
020ec727a6 i2c: sh_i2c.c: support I2C2, I2C3 and I2C4
sh_i2c.c support I2C0 and I2C1. This patch extends it to I2C4.

Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
2012-10-16 05:47:20 +02:00
Tetsuyuki Kobayashi
3ce2703d8f i2c: sh_i2c.c: adjust for SH73A0
Adjust i2c_raw_read() in sh_i2c.c to work for SH73A0.
After this patch, "i2c md" and "i2c mw" command on U-Boot work properly on KZM-A9-GT board.

Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
2012-10-16 05:47:20 +02:00
Tetsuyuki Kobayashi
57d7c80472 i2c: sh_i2c.c: correct BUSY bit define in ICSR
Correct BUSY bit define in ICSR from (1<<3) to (1<<4).

Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
2012-10-16 05:47:19 +02:00
Tetsuyuki Kobayashi
b1af67fe5e i2c: sh_i2c.c: support iccl and icch extension
R-mobile SoC (at least SH73A0) has extension bits to store 8th bit of iccl and icch.
This patch add support for the extentin bits.

Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
2012-10-16 05:47:19 +02:00
Matthias Weisser
e7bed5c2b3 imx: Use MXC_I2C_CLK in imx i2c driver
i2c didn't work on imx25 due to missing MXC_IPG_PERCLK. Now using
MXC_I2C_CLK on all imx systems using i2c.

Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:10 -07:00
Tom Warren
150c24936b Tegra20: Move some include files to arch-tegra for sharing with Tegra30
The move is pretty straight-forward. ap20.h and tegra20.h were renamed to ap.h and tegra.h.
Some files remain in arch-tegra20 but 'include' a file in 'arch-tegra' with #defines & structs
that will be common between T20 and T30 HW. HW-specific #defines, etc. stay in the 'arch-tegra20'
'root' file.

All boards build OK w/MAKEALL -s tegra20. Checkpatch.pl runs clean. Seaboard works OK.

Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-15 11:54:06 -07:00
Nobuhiro Iwamatsu
96d1e0933f i2c: sh: Remove irq_wait function
irq_wait function is not referred to from anywhere.

Reported-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2012-10-03 08:47:17 +02:00
Tom Rini
495dbd72dd Merge branch 'master' of git://git.denx.de/u-boot-arm 2012-09-21 14:53:13 -07:00
Tom Warren
29f3e3f248 Tegra: Change Tegra20 to Tegra in common code, prep for T30
Convert TEGRA20_ defines to either TEGRA_ or NV_PA_ where appropriate.
Convert tegra20_ source file and function names to tegra_, also.

Upcoming Tegra30 port will use common code/defines/names where possible.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
2012-09-10 13:01:24 -07:00
Koen Kooi
a532278074 omap4 i2c: add support for i2c bus 4
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
2012-09-06 06:01:09 +02:00
Otavio Salvador
fa7a51cb82 mxs: Convert sys_proto.h prefixes to 'mxs'
The sys_proto.h functions (except the boot modes) are compatible with
i.MX233 and i.MX28 so we use 'mxs' prefix for its methods.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2012-09-01 14:58:25 +02:00
Allen Martin
00a2749d7b tegra20: rename tegra2 -> tegra20
This is make naming consistent with the kernel and devicetree and in
preparation of pulling out the common tegra20 code.

Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-09-01 14:58:21 +02:00
Otavio Salvador
9c471142bc mxs: prefix register structs with 'mxs' prefix
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2012-09-01 14:58:17 +02:00
Ilya Yanok
55faa58976 omap24xx_i2c: add 2-byte address support
Various devices like EEPROMs require 2-byte address support to
be properly accessed. This patch adds this support for OMAP2/3/4
I2C controller driver.
I've tested it with EEPROM (16 bit address) and TPS65217 chip
(8 bit address) on TI Beaglebone board.

Unfortunately I don't have access to any compatible hardware
with 16bit data register so I can't test if those #ifdef
clauses really work.

CC: Tom Rini <trini@ti.com>
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-09-01 14:58:08 +02:00
Rajeshwari Shinde
178239de19 I2C: Add support for Multi channel
This adds multiple i2c channel support for I2C.

Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
2012-07-31 08:03:03 +02:00
Rajeshwari Shinde
ab7e52bb24 I2C: Modify the I2C driver for EXYNOS5
This patch modifies the S3C I2C driver to suppport EXYNOS5.
The cahnges made to driver are as follows:
        - I2C base address is passed as a parameter to many
        functions to avoid multiple #ifdef
        - Channel initialisation is moved to a commom funation
        as it is required by i2c_init.
        - Hardcoding for I2CCON_ACKGEN removed.
        - Replaced printf with debug.
        - Checkpatch issues resolved.
        - Pinmux setting will be done in board/samsung/smdk5250/smdk5250.c
        to avoid repeated setting of gpio lines, as it have multi bus support.

Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
2012-07-31 08:02:51 +02:00
Rajeshwari Shinde
91dffb16ff I2C: Move struct s3c24x0_i2c to a common place.
struct s3c24x0_i2c is being moved to common local header file so that
the same can be used by s3c series and exynos series SoCs.

Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
2012-07-31 08:02:41 +02:00
Troy Kisky
9815326d04 mxc_i2c: finish adding CONFIG_I2C_MULTI_BUS support
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-07-31 07:59:41 +02:00
Troy Kisky
96c19bd3ef mxc_i2c: add bus recovery support
Add support for calling a function that will toggle the
SCL line to return the bus to idle condition.

The actual toggling function is added in a later patch.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-07-31 07:59:26 +02:00
Troy Kisky
e4ff525f91 mxc_i2c: prep work for multiple busses support
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-07-31 07:57:04 +02:00
Troy Kisky
27a5da02c0 mxc_i2c: add i2c_regs argument to i2c_imx_stop
This is prep work for CONFIG_I2C_MULTI_BUS.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
2012-07-31 07:55:13 +02:00
Troy Kisky
a7f1a00510 mxc_i2c: add retries
Retry unexpected hardware errors. This
will not retry a received NAK.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-07-31 07:53:36 +02:00
Troy Kisky
d5383a63cd mxc_i2c: check for arbitration lost
No need to continue waiting if arbitration lost.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
2012-07-31 07:53:24 +02:00
Troy Kisky
ca741da106 mxc_i2c: change slave addr if conflicts with destination.
The i2c controller cannot be both master and slave in the
same transaction.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-07-31 07:52:53 +02:00
Troy Kisky
90a5b70f59 mxc_i2c: don't disable controller after every transaction
This helps in a multiple bus master environment which
is why I also added a wait for bus idle.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-07-31 07:51:22 +02:00
Troy Kisky
83a1a19038 mxc_i2c: place i2c_reset code inline
imx_reset is only referenced once so
move to that location.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
2012-07-31 07:49:48 +02:00
Troy Kisky
71e9f3cbeb mxc_i2c: place imx_start code inline
imx_start is only referenced once so
move to that location.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
2012-07-31 07:46:06 +02:00
Troy Kisky
d45e75b10c mxc_i2c: remove redundant read
wait_for_sr_state returns i2sr on success
so no need to read again.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
2012-07-31 07:45:00 +02:00
Troy Kisky
7aa57a01c0 mxc_i2c: combine i2c_imx_bus_busy and i2c_imx_trx_complete into wait_for_sr_state
Not using udelay gives a more accurate timeout. The current implementation of udelay
in imx-common does not seem to wait at all for a udelay(1).

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>

----
V2: Added WATCHDOG_RESET as suggested by Marek Vasut
add error message when stop fails

mxc_i2c: code i2c_probe as a 0 length i2c_write

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-07-31 07:44:25 +02:00
Troy Kisky
cfbb88d338 mxc_i2c.c: code i2c_probe as a 0 length i2c_write
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-07-31 07:43:51 +02:00
Troy Kisky
c4330d283c mxc_i2c: call i2c_imx_stop on error in i2c_read/i2c_write
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-07-31 07:43:25 +02:00
Troy Kisky
b230ddc267 mxc_i2c: create i2c_init_transfer
Initial code of i2c_read and i2c_write
is identical, move to subroutine.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-07-31 07:42:58 +02:00
Troy Kisky
ea572d853e mxc_i2c: clear i2sr before waiting for bit
Let's clear the sr register before waiting for
bit to be set, instead of clearing it after
hardware sets it. No real operational difference here,
but allows combining of i2c_imx_trx_complete and
i2c_imx_bus_busy in later patches.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
2012-07-31 07:42:20 +02:00
Troy Kisky
cea60b0c6c mxc_i2c: create tx_byte function
Use tx_byte function instead of having 3 copies
of the code.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
2012-07-31 07:41:51 +02:00
Troy Kisky
24cd738bc4 mxc_i2c: remove ifdef of CONFIG_HARD_I2C
This is always selected when CONFIG_I2C_MXC is
selected, so it adds no value.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
2012-07-31 07:41:23 +02:00
Troy Kisky
1c076dba27 mxc_i2c: fix i2c_imx_stop
Instead of clearing 2 bits, all the other
bits were set because '|=' was used instead
of '&='.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-07-31 07:40:59 +02:00
Torsten Fleischer
fa86d1c0bf mxs-i2c: Fix internal address byte order
Large EEPROMs, e.g. 24lc32, need 2 byte to address the internal memory.
These devices require that the high byte of the internal address has to be
written first.
The mxs_i2c driver currently writes the address' low byte first.

The following patch fixes the byte order of the internal address that should
be written to the I2C device.

Signed-off-by: Torsten Fleischer <to-fleischer@t-online.de>

CC: Marek Vasut <marex@denx.de>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-07-11 10:54:53 +02:00
Troy Kisky
9ca37d78a3 mxc_i2c: remove setting speed at each start
Other then being very weird, this code was also wrong.
For example, say I set speed to 100K. I'll read back the speed
as 85937. But the speed is really 85937.5, so we I reset
the speed to 85937, I'll get 73660.7. After a couple of transactions
my speed is now exactly 68750 so it will remain there.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-07-11 10:54:52 +02:00
Troy Kisky
de6f604de2 mxc_i2c: specify i2c base address in config file
The following platforms had their config files changed
flea3, imx31_phycore, mx35pdk, mx53ard, mx53evk, mx53smd
and mx53loco.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-07-11 10:54:29 +02:00
Stefan Roese
496ba48f5e i2c: designware_i2c.c: Add support for the "i2c probe" command
i2c_probe() is changed to reinit the i2c bus upon read failure.
This is naturally the case upon i2c bus probing.

Also, some printf messages upon read failure are removed. As they
would interfere with the "i2c probe" command.

Additionally, i2c_set_bus_speed() now returns 0, so that the
"i2c speed" command can be used.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
2012-07-07 14:07:43 +02:00
Tom Rini
402d17fc4c omap24xx_i2c: Add AM33XX support
The same places that check for CONFIG_OMAP44XX need to check for
CONFIG_AM33XX as we share the same i2c block.

Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
2012-07-07 14:07:23 +02:00
Tom Rini
168a5acb81 Revert "I2C: OMAP: detect more devices when probing an i2c bus"
This reverts commit 0e57968a21.

The short version of the original commit is that some i2c devices cannot
be probed via read as they NAK the first cycle, so try and probe via a
write that we abort before it writes to the device.  This however is not
allowed by the TRM for any of these parts.  The section on I2C_CON
(table 17-35 I2C_CON for am/dm37x for example) says you must not change
the register while STT has been set.  On these parts, the unpredictable
behavior that the chip exhibits is not problematic.  On OMAP4 however it
results in the chip being in a bad state:
Panda # i2c probe
Valid chip addresses: 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12
13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A
2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 40 41 42
43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50 51 52 53 54 55 56 57 58 59 5A
5B 5C 5D 5E 5F 60 61 62 63 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F 70 71 72
73 74 75 76 77 78 79 7A 7B 7C 7D 7E 7F
Panda # i2c md 50 0
timed out in wait_for_pin: I2C_STAT=0
I2C read: I/O error
Error reading the chip.

We must revert the original behavior to bring probe back into line with
the TRM.

Cc: Nick Thompson <nick.thompson@ge.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
2012-07-07 14:07:22 +02:00
Simon Glass
e31c1e50ac tegra: i2c: Add function to find DVC bus
Add tegra_i2c_get_dvc_bus_num() to obtain the I2C bus number of DVC bus.
This allows us to talk to the PMU.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-05-15 08:31:39 +02:00
Armando Visconti
5e3e8dda51 i2c:designware Turn off the ctrl when setting the speed
The designware i2c controller must be turned off before
setting the speed in IC_CON register, as stated in the
section 6.3.1 of the dw_apb_i2c_db.pdf.

Signed-off-by: Michel Sanches <michel.sanches@st.com>
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
2012-04-24 09:57:00 +02:00
Vipin KUMAR
031ed2fa74 i2c: Add support for designware i2c controller
Earlier, a driver exists in the u-boot source for designware i2c interface. That
driver was specific to spear platforms. This patch implements the i2c controller
as a generic driver which can be used by multiple platforms

The driver files are now renamed to designware_i2c.c and designware_i2c.h and
these are moved into drivers/i2c folder for reusability by other
platforms

Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
2012-04-24 09:56:37 +02:00
Nobuhiro Iwamatsu
2d344a2ab2 sh: i2c: Add support I2C controller of SH7734
Renesas SH7734 has two I2C interfaceis.
This supports these I2C.

V5: - include i2c.h.
    - Add check of icsr bit polling logic.
	- Implement i2c_probe.
V4: - Remove sh_i2c_dump_reg function.
    - Use puts() when there's no format.
    - Chnage check for I2C bus number.
    - Remove space before the semi-colon.
V3: - Fix error for whitespace.
V2: - Changed bit control to use the clr|set|clrsetbits_* functions.
    - Fix wrong comment style.
    - Add new line before for loop in i2c_read.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-04-24 09:40:04 +02:00
Yen Lin
96a78ac0c4 tegra: i2c: Add I2C driver
Add basic i2c driver for Tegra2 with 8- and 16-bit address support.
The driver requires CONFIG_OF_CONTROL to obtain its configuration
from the device tree.

(Simon Glass: sjg@chromium.org modified for upstream)

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-03-29 08:12:50 +02:00
Tom Rini
cec487a435 Revert "ARM: I2C: I2C Multi byte address support"
This reverts commits 2faa76196a as
this has introduced some large problems on all other platforms and have
more changes in them than the commit message implies.

Cc: Heiko Schocher <hs@denx.de>
Cc: Patil, Rachna <rachna@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-02-21 07:28:47 +01:00
Tom Rini
c2459a405b Revert "ARM: AM33XX: Add AM33XX I2C driver support"
This reverts commit 498cbdfe62 as we need
to revert the i2c changes that add the support for the platform.

Cc: Heiko Schocher <hs@denx.de>
Cc: Patil, Rachna <rachna@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-02-21 07:28:29 +01:00
Patil, Rachna
498cbdfe62 ARM: AM33XX: Add AM33XX I2C driver support
1. Compliant with Philips I2C specification version 2.1
2. Supports upto 100Kbps in standard mode

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Patil, Rachna <rachna@ti.com>
2012-01-23 11:57:31 +01:00
Patil, Rachna
2faa76196a ARM: I2C: I2C Multi byte address support
Existing OMAP I2C driver does not support address
length greater than one. Hence this patch is to
add support for 2 byte address read/write.

Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Patil, Rachna <rachna@ti.com>
2012-01-23 11:57:31 +01:00
Andreas Müller
0b620ec97e drivers/i2c/omap24xx_i2c.c: move all local variables to SRAM
At old overo boards TWL4030 RTC irq is connected to gpio112. Unfortunately
this pin is also used for revision detection. Therefore we need to send
shut-up to TWL4030 to avoid reading wrong revision. In SPL this must
be done before SDRAM is set up because the type of SDRAM is revision dependent.
By this patch it is ensured that all variables used by omap24xx_i2c.c are
located in SRAM.

Signed-off-by: Andreas Müller <schnitzeltony@gmx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
2012-01-16 08:40:12 +01:00
Andreas Müller
49e9b4bd9b drivers/i2c/omap24xx_i2c.c: replace printf with one argument by puts
Signed-off-by: Andreas Müller <schnitzeltony@gmx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2012-01-16 08:40:12 +01:00
Anatolij Gustschin
bd0f5ca806 drivers/i2c/davinci_i2c.c: Fix GCC 4.6 warning
Fix:
davinci_i2c.c: In function 'flush_rx':
davinci_i2c.c:81:6: warning: variable 'dummy' set but not used
[-Wunused-but-set-variable]

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2011-11-23 21:22:39 +01:00
Nobuhiro Iwamatsu
3dab3e0e67 i2c: sh: Add support I2C for Renesas SH
This supports I2C of Renesas SH.
I tested on SH7724.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Heiko Schocher <hs@denx.de>
2011-11-23 21:22:26 +01:00
Wolfgang Denk
0c2dd9a05b Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
  arm, davinci: add DAVINCI_MMC_CLKID
  arm, davinci_emac: fix driver bug if more then 3 PHYs are detected
  arm, davinci: da850/dm365 lowlevel cleanup
  omap5: Add omap5_evm board build support.
  omap4/5: Add support for booting with CH.
  omap5: emif: Add emif/ddr configurations required for omap5 evm
  omap5: clocks: Add clocks support for omap5 platform.
  omap5: Add minimal support for omap5430.
  omap: Checkpatch fixes
  omap4: make omap4 code common for future reuse
  GCC4.6: Squash warnings in onenand_base.c
  GCC4.6: Fix common/usb.c on xscale
  OneNAND: Add simple OneNAND SPL
  PXA: vpac270: Enable the new generic MMC driver
  PXA: Cleanup serial_pxa
  PXA: Drop csb226 and innokom boards (unmaintained)
  m28evk: Fix comment about the number of RAM banks
  mx31: Fix checkpatch warnings in generic.c
  mx31: Use proper IO accessor for GPR register
  mx31: Remove duplicate definition for GPR register
  qong: Use generic function for configuring GPR register
  M28EVK: Enable USB HOST support
  iMX28: Add USB HOST driver
  iMX28: Add USB and USB PHY register definitions
  M28: Add memory detection into SPL
  iMX28: Fix ARM vector handling
  M28: Add doc/README.m28 documentation
  M28: Add MMC SPL
  iMX28: Add support for DENX M28EVK board
  iMX28: Add u-boot.sb target to Makefile
  iMX28: Add image header generator tool
  iMX28: Add driver for internal RTC
  iMX28: Add GPMI NAND driver
  iMX28: Add APBH DMA driver
  iMX28: Add SPI driver
  iMX28: Add GPIO control
  iMX28: Add I2C bus driver
  iMX28: Add PINMUX control
  FEC: Add support for iMX28 quirks
  iMX28: Add SSP MMC driver
  iMX28: Initial support for iMX28 CPU
  MX25: zmx25: GCC4.6 fix build warnings
  da850: add new config file for AM18xx
  BeagleBoard: config: Switch to ttyO2
  OMAP3: Change omap3_evm maintainer
  devkit8000: Fix NAND SPL on boards with 256MB NAND
  integrator: enable Vpp and disable flash protection
  integrator: add system controller header
  integrator: make flash writeable on boot
  integrator: use io-accessors for board init
  integrator: move text offset to config
  integrator: pass configs for core modules
  ARM: remove superfluous setting of arch_number in board specific code.
  SPL: Allow ARM926EJS to avoid compiling in the CPU support code
  integrator: do not test first part of the memory
  arm: a320: fix broken timer
  ARM: define CONFIG_MACH_TYPE for all ronetix boards
  dm646x: pass board revision info to kernel
  dm646x: add new configuration for dm6467T
  arm, davinci: Fix setting of the SDRAM configuration register
  arm, davinci: Remove the duplication of LPSC functions
  arm, davinci: Rename AM1808 lowlevel functions to DA850
  da8xxevm: fix build error
  ARM: re-add MACH_TYPE_XXXXXX for VCMA9 board and add CONFIG_MACH_TYPE
2011-11-16 20:24:41 +01:00
Marek Vasut
f4f680aa36 iMX28: Add I2C bus driver
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Acked-by: Heiko Schocher<hs@denx.de>
2011-11-11 11:36:57 +01:00
Kumar Gala
aa5512157b fsl_i2c: Fix compile warning
fsl_i2c.c: In function 'i2c_init':
fsl_i2c.c:245:7: warning: assignment discards qualifiers from pointer target type

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-09 06:28:20 +01:00
Wolfgang Denk
688d8f33f2 Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
  Arm: re-introduce the MACH_TYPE_XXXXXX for EB_CPUX9K2 board
  arm: jadecpu: Readd MACH_TYPE_JADECPU
  at91: defined mach-types for otc570 board in board config file
  at91: defined mach-types for meesc board in board config file
  mx31pdk: Enable D and I caches
  ehci-mxc: remove incorrect comment
  README: Fix supported i.MX SoC list for CONFIG_MXC_SPI
  mx53: Turn off child clocks before reconfigure perclk_root
  qong: enable support for compressed images
  imx: imx31_phycore.h: fix checkpatch warnings
  vision2: Remove unused get_board_rev function
  mx53smd: Remove unused get_board_rev function
  mx53ard: Remove unused get_board_rev function
  mx53evk: Remove unused get_board_rev function
  mx53evk: Add RTC support
  mx53loco: Remove unused get_board_rev function
  mx53evk: Remove unneeded '1' from mx53evk.h
  OMAP3: mvblx: Initial support for mvBlueLYNX-X
  ARM: dig297: Define MACH_TYPE_OMAP3_CPS and CONFIG_MACH_TYPE
  omap3: mem: Move comments next to definitions
  omap3: mem: Clean-up whitespaces
  omap3: mem: Define and use common macros
  Davinci: ea20: added PREBOOT to configuration
  Davinci: ea20: added I2C support
  Davinci: ea20: added video support
  VIDEO: davinci: add framebuffer to da8xx
  ARM: Davinci: added missing registers to hardware.h
  Davinci: ea20: add gpios for LCD backlight control
  Davinci: ea20: add gpio for keeping power on in board_late_init
  Davinci: ea20: Add default U-Boot environment
  Davinci: ea20: Add early init to get early output from console
  Davinci: ea20: Add NAND support
  Davinci: ea20: set GPIOs to hold MII-Phy in reset and set UART0-Switch for console
  Davinci: ea20: set console on UART0
  arm, davinci: add cam_enc_4xx support
  arm926ejs, davinci: add missing spi defines for dm365
  arm926ejs, davinci: add cpuinfo for dm365
  arm, davinci: add lowlevel function for dm365 soc
  arm, davinci: add header files for dm365
  spl, nand: add 4bit HW ecc oob first nand_read_page function
  arm, davinci: add support for new spl framework
  spl: add option for adding post memory test to the SPL framework
  net, davinci_emac: make clock divider in MDIO control register configurable
  arm, usb, davinci: make USBPHY_CTL register configurable
  usb, davinci: add enable_vbus() weak function
  omap3evm: fix errors caused by multiple definitions
  omap3evm: Add (quick) configuration for NAND only
  omap3evm: Add (quick) configuration for MMC/SD only
  omap3evm: move common config options to new file
  omap3evm: Prepare to split configuration
  omap3evm: Reorder related config options
  omap/spl: actually enable the console
  davinci_emac: compilation fix, phy is array now
  omap3evm: Set environment variable 'ethaddr'
  arm, arm926: fix missing symbols in NAND_SPL mode
  arm, davinci: Add function lpsc_syncreset()
  arm, davinci: replace CONFIG_PRELOADER with CONFIG_SPL_BUILD
  arm/km: portl2 environment address update to P1B
  arm/km: adapt bootcounter evaluation
  arm/km: enable jffs2 cmds
  arm/km: trigger reconfiguration for the Xilinx FPGA
  arm/km: add boardid and hwkey to kernel command line
  ARM: Reintroduce MACH_TYPE_KM_KIRKWOOD for keymile ARM boards
  netspace_v2: enable I2C EEPROM support
  netspace_v2: fix SDRAM configuration
  armada100: define CONFIG_SYS_CACHELINE_SIZE
  pantheon: define CONFIG_SYS_CACHELINE_SIZE
  kirkwood: define CONFIG_SYS_CACHELINE_SIZE
  kirkwood: drop empty asm-offsets.s file
  arm/km/mgcoge3un: enhance "waitforne" feature
  arm/km: add variable waitforne to mgcoge3un
  gplugD: Fix for error:MACH_TYPE_SHEEVAD undeclared
  ARM: dreamplug: fix compilation
  ARM: DockStar: fix compilation
  ARM: netspace_v2: fix warnings
  am335x: Drop board_sysinfo struct
  am335x: Temporarily add MACH_TYPE define
  misc:pmic:samsung Enable PMIC driver at C210 Universal target
  dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p UNIVERSAL C210 target
  dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p GONI target
  smdkv310: use macro for mmc data read function address
  smdkv310: use spl framework for mmc spl
  SMDKV310: use get_ram_size() to validate dram size
  SMDKV310: Initialize board id using CONFIG_MACH_TYPE
  ORIGEN : use absolute paths and fix tool naming
  ORIGEN : enable device tree support
  MX25: tx25: Fix building due to missing MACH_TYPE
  mx31: Add board support for HALE TT-01
  mx31: add ESD control registers
  mx31: define pins and init for UART2 and CSPI3
  MX35: add support for flea3 board
  MX51: vision2: add MACH_TYPE in config file
  vision2: Remove unused header file
  mx51evk: Remove unused get_board_rev function
  mx51evk: Remove unneeded '1' from mx51evk.h
  I2C: Fix mxc_i2c.c problem on imx31_phycore
  mx35pdk: Add RTC support
  mx51evk: Use GPIO API for configuring the IOMUX
  mx51evk: Add RTC support
  rtc: Make mc13783-rtc driver generic
  qong: remove unneeded IOMUX settings
  qong: Use mx31_set_gpr to setup USBH2 pins
  mx31: Introduce mx31_set_gpr function
  mx31pdk: Add MC13783 PMIC support
  qong: remove unneeded "1" from qong.h
  misc: pmic: fix regression in pmic_fsl.c (SPI)
  mx5 configs: CONFIG_PRIME should really be CONFIG_ETHPRIME
  MX35: Drop unnecessary prototypes from imx-regs.h
  I2C: added I2C-2 and I2C-3 to MX35
  MX35: factorize common assembly code
  MX35: add reset cause as provided by other i.MX
  MX35: add pins definition for UART3
  MX35: added ESDC structure to imx-regs
2011-11-08 00:38:52 +01:00
Jerry Huang
c9a8b25ef9 Powerpc/i2c: Use the same initialize codes
Make the I2C2 and I2C1 use the same initialize codes.

Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
2011-11-04 06:21:26 +01:00
Marek Vasut
bf0783df0d I2C: Fix mxc_i2c.c problem on imx31_phycore
The problem was caused by a global variable being used early in the boot
process.

The symptoms were on imx31_phycore board, reading the environment from I2C
EEPROM didn't work correctly and causes default environment to be loaded.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Tested-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
2011-11-03 22:56:19 +01:00
Stefano Babic
a1c662965d I2C: added I2C-2 and I2C-3 to MX35
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2011-11-03 22:56:18 +01:00
Marek Vasut
b567b8ff79 I2C: Add i2c_get/set_speed() to mxc_i2c.c
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2011-10-27 21:56:30 +02:00
Lei Wen
d308c9d35a I2C: mv_i2c: fix multi-bus init issue
When enable the multi-bus, the current_bus is not inited in the original
implementation, which make the i2c operation unpredicatable.

Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-10-03 11:50:09 +02:00
Lei Wen
2be1ed349c I2C: mv_i2c: fix build issue when enable debug option
When DEBUG_I2C is open, the following build issue would shows up.

mv_i2c.c: In function 'i2c_transfer':
mv_i2c.c:257: error: 'ISR' undeclared (first use in this function)
mv_i2c.c:257: error: (Each undeclared identifier is reported only once
mv_i2c.c:257: error: for each function it appears in.)

Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-10-03 11:47:07 +02:00
Graeme Russ
e3e454cd72 console: Squelch pre-console output in console functions
There are some locations in the code which anticipate printf() being called
before the console is ready by squelching printf() on gd->have_console.
Move this squelching into printf(), vprintf(), puts() and putc(). Also
make tstc() and getc() return 0 if console is not yet initialised

Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Tested-by: Simon Glass <sjg@chromium.org>
2011-10-01 21:54:49 +02:00
Marek Vasut
db84140bb7 I2C: mxc_i2c rework
Rewrite the mxc_i2c driver.
 * This version is much closer to Linux implementation.
 * Fixes IPG_PERCLK being incorrectly used as clock source
 * Fixes behaviour of the driver on iMX51
 * Clean up coding style a bit ;-)

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Jason Hui <jason.hui@linaro.org>
Acked-by: Jason Liu <jason.hui@linro.org>
Acked-by: Heiko Schocher <hs@denx.de>
Tested-by: Jason Liu <jason.hui@linro.org>
2011-09-30 22:01:05 +02:00
Heiko Schocher
49d6da6032 i2c, davinci: add i2c set speed
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Paulraj Sandeep <s-paulraj@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30 22:00:56 +02:00
Michael Jones
89677b27d3 ARMV7: OMAP: I2C driver: cosmetic: make checkpatch-compatible
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-12 17:40:48 +02:00
Michael Jones
0607e2b97a ARMV7: OMAP: Write more than 1 byte at a time in i2c_write
This allows the EEPROM layer to send a single i2c write command
per page, and wait CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS between
i2c write commands.

Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-12 17:40:48 +02:00
Stefano Babic
30032710ed I2C: mxc: fix compilation for MX31
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2011-09-07 22:11:47 +02:00
Michael Jones
f9a78b8d4f cosmetic: spell fixes etc.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Acked-by: Detlev Zundel <dzu@denx.de>
2011-07-28 16:32:50 +02:00
Michael Brandt
d3d6427a3f I2C: Add driver for ST-Ericsson U8500 i2c
Signed-off-by: John Rigby <john.rigby@linaro.org>
CC: Heiko Schocher <hs@denx.de>
2011-06-01 19:22:47 +02:00
Heiko Schocher
4bd5566ee8 i2c, soft_i2c: deblock bus if switching to another i2c bus
Deblock i2c bus when switching to another i2c bus, if using
i2c_set_bus_num().

Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2011-04-28 10:57:08 +02:00
Albert ARIBAUD
57b4bce996 Replace obsolete e-mail address
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-04-27 19:38:09 +02:00
Lei Wen
adb00bb6a0 I2C: mv_i2c: add multi bus support
Add the ability to support multiple i2c bus for mv_i2c

Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-04-27 19:38:08 +02:00
Lei Wen
3df619ec2c mv_i2c: use structure to replace the direclty define
Add i2c_clk_enable in the cpu specific code, since previous platform it,
while new platform don't need. In the pantheon and armada100 platform,
this function is defined as NULL one.

Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-04-27 19:38:08 +02:00
Lei Wen
879de1275a mv_i2c: fix timeout value to be consistent with comments
The original 10000 value would be 100ms, which is not
the comments said.

Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-04-27 19:38:07 +02:00
Lei Wen
68432c2743 pxa: move i2c driver to the common place
For better sharing with other platform other than pxa's,
it is more convenient to put the driver to the common place.

Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-04-27 19:38:07 +02:00
Stefano Babic
8627111543 IMX: MX31: Cleanup include files and drop nasty #ifdef in drivers
As exception among the i.MX processors, the i.MX31 has headers
without general names (mx31-regs.h, mx31.h instead of imx-regs.h and
clock.h). This requires several nasty #ifdef in the drivers to
include the correct header. The patch cleans up the driver and
renames the header files as for the other i.MX processors.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2011-04-27 19:38:05 +02:00
Nick Thompson
0e57968a21 I2C: OMAP: detect more devices when probing an i2c bus
The omap24xx driver only seems to support devices that have a single subaddress
byte. With these types of devices, the first access in a bus transaction is
usually a write (writes the subaddress) followed by either a read or write to
access the devices registers.

Many such devices will respond to a read as the first access, but there are at
least some that will NACK such a read. (e.g. ADV7180.)

The probe function attempts to detect a devices ACK to a read access only and
fails to find devices that NACK a read.

This commit modifies the probe function to start a write instead. This detects
devices that respond to reads (since they must also respond to writes) as well
as those that only respond to writes. The bus is immediately set to idle after a
(N)ACK avoiding actually writing anything to the device.

Signed-off-by: Nick Thompson <nick.thompson@ge.com>
2011-04-14 08:33:23 +02:00
Stefano Babic
81687212ee I2C: mxc_i2c: address failure with mx35 processor
There is sporadic failures when more as one I2C slave
is on the bus and the processor tries to communicate
with more as one slave.
The problem was seen on a mx35pdk (two I2C slaves,
PMIC controller and CAN/RTC chip).

The current driver uses the IIF bit in the status register
to check if the bus is busy or not. According to the manual,
this is not correct, because the IIB bit should be checked.
Not only, to check if a transfer is finished must be checked
the ICF bit, and this is not tested at all.

This patch comes from analyse with a corresponding driver
provided by Freescale as part of the LTIB tool. Comparing
the two drivers, it appears that the current u-boot driver checks
the wrong bits, and depending on race condition, the transfer
can be successful or not.

The patch gets rid also of own debug function (DPRINTF),
replaced with the general debug().

Tested on Freescale mx35pdk.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2011-02-02 00:54:43 +01:00
Stefano Babic
1d549ade61 I2C: mxc_i2c: get rid of __REG access
This driver accesses to processor's register
via __REG macros, that are removed (or are planned
to be removed) and replaced by C structures.
This patches replaces all occurrencies of __REG macros.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2011-02-02 00:54:42 +01:00
Stefano Babic
04220612f6 mxc_i2c: Add support for the i.MX35 processor
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2011-02-02 00:54:42 +01:00
Liu Hui-R64343
127cec1889 mxc_i2c: add support for MX53 processor
This patch add I2C support for Freescale MX53 processor

Signed-off-by: Jason Liu <r64343@freescale.com>
2011-02-02 00:54:42 +01:00
Ryan Mallon
f3100ff767 Fix at91 includes in soft_i2c driver
Make at91 header includes in soft_i2c depend only on CONFIG_AT91FAMILY
rather than individual SoCs.

Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Reinhard Meyer<u-boot@emk-elektronik.de>
2011-01-27 07:27:32 +01:00
John Rigby
2956532625 Move DECLARE_GLOBAL_DATA_PTR to file scope
It can be optimised out by the compiler otherwise resulting
in obscure errors like a board not booting.

This has been documented in README since 2006 when these were
first fixed up for GCC 4.x.

Signed-off-by: John Rigby <john.rigby@linaro.org>

Fix some additional places.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-By: Albert ARIBAUD <albert.aribaud@free.fr>
2010-12-21 11:33:36 +01:00
Sebastien Carlier
6d8962e814 Switch from archive libraries to partial linking
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils.  As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".

This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.

The name of each former library archive is preserved except for
extensions which change from ".a" to ".o".  This commit updates
references accordingly where needed, in particular in some linker
scripts.

This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols.  Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.

Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
2010-11-17 21:02:18 +01:00
Wolfgang Denk
17dd883c5b Merge branch 'master' of git://git.denx.de/u-boot-samsung 2010-10-29 21:47:48 +02:00
C Nauman
d9abba8254 Add generic support for samsung s3c2440
This patch adds generic support for the Samsung s3c2440 processor.

Global s3c24x0 changes to struct members converting from upper case to
lower case.

Signed-off-by: Craig Nauman <cnauman@diagraph.com>
Cc: kevin.morfitt@fearnside-systems.co.uk
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2010-10-28 15:35:56 +09:00
Steve Sakoman
4df6689495 ARMV7: OMAP: I2C driver: Fix bug found in 37XX testing
On OMAP36/37XX the standard on chip pullups are not sufficient to
ensure proper i2c operation without external pullups or switching
to high speed mode and enabling special on chip pullups.

This is an issue for Beagle xM, which does not have external pullups
on the expansion board i2c lines.

The issue manifests itself as an AL (arbitration lost) error when
probing for a non-existent device (i.e. on a Beagle xM with no expansion
boards attached).  This issue does not occur on expansion boards that
include pullups or on Overo 37XX COM's since they include pull-ups.

This patch fixes the issue by checking for the AL bit in the i2c_probe
function.

Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
2010-10-25 07:57:20 +02:00
Steve Sakoman
fbad355562 ARMV7: OMAP: I2C driver: Restructure i2c_probe function
This patch removes the "magic number" delays and instead
monitors state changes in the status register bits.

Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Tested-by: Heiko Schocher <hs@denx.de>
2010-10-20 15:28:48 +02:00
Steve Sakoman
d480c46773 ARMV7: OMAP: I2C driver: Restructure i2c_write_byte function
This patch removes the "magic number" delays and instead
monitors state changes in the status register bits.

Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Tested-by: Heiko Schocher <hs@denx.de>
2010-10-20 15:28:41 +02:00
Steve Sakoman
da0cc665bc ARMV7: OMAP: I2C driver: Restructure i2c_read_byte function
This patch removes the "magic number" delays and instead
monitors state changes in the status register bits.

Signed-off-by: Steve Sakoman <steve.sakomanlinaro.org>
Tested-by: Heiko Schocher <hs@denx.de>
2010-10-20 15:28:37 +02:00
Steve Sakoman
73e8747fe4 ARMV7: OMAP: I2C driver: Use same timeout value as linux kernel driver
This patch matches the poll interval (1 millisecond) and timeout (1 second)
used in the linux driver. It also adds a return value of 0 in the event of
a timeout error and cleans up some formatting errors in that section of the
code.

Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Tested-by: Heiko Schocher <hs@denx.de>
2010-10-20 15:28:33 +02:00
Stefan Roese
b36df56115 ppc4xx: Move ppc4xx headers to powerpc include directory
This patch moves some ppc4xx related headers from the common include
directory (include/) to the powerpc specific one
(arch/powerpc/include/asm/). This way to common include directory is not
so cluttered with files.

Signed-off-by: Stefan Roese <sr@denx.de>
2010-09-23 09:02:05 +02:00
Heiko Schocher
1724fe9adf i2c, omap24xx: set bus_initialized only after relocation.
Portions of this work were supported by funding from
the CE Linux Forum.

Signed-off-by: Heiko Schocher <hs@denx.de>
2010-09-19 19:29:52 +02:00
Wolfgang Denk
2d941de9d5 Prepare v2010.09-rc1
Coding style cleanup.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-09-10 00:16:19 +02:00
Albert Aribaud
306563a773 i2c: rewrite mvtwsi, support orion5x and kirkwood
This rewrite of the mvtwsi driver is 25% smaller and much
faster and simpler than the previous code.

Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Acked-by: Prafulla Wadaskar<prafulla@marvell.com>
Acked-by: Heiko Schocher<hs@denx.de>
2010-08-30 14:10:35 +02:00
Albert Aribaud
01ec99d969 i2c: rename kirkwood_i2c to mvtwsi
This driver is not kirkwood-specific and can also be used
e.g. by orion5x. Rename to a SoC-neutral name.

Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Acked-by: Prafulla Wadaskar<prafulla@marvell.com>
Acked-by: Heiko Schocher<hs@denx.de>
2010-08-30 14:10:23 +02:00
Nishanth Menon
07cf5e207e i2c: omap2+: change header guard to be generic
Make the header guard to be generic to stop conflicting with
omap2 i2c header file arch/arm/include/asm/arch-omap24xx/i2c.h

Cc: Steve Sakoman <steve@sakoman.com>
Cc: Heiko <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Wolfang Denk <wd@denx.de>

Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Steve Sakoman <steve@sakoman.com>
2010-08-23 08:08:31 +02:00
Steve Sakoman
d708395d2f ARMV7: Modify i2c driver for more reliable operation on OMAP4
This patch modifies the init routine to follow the TRM
recommendations. It also modifies the i2c_read_byte function
to reflect subtle differences between the i2c controller in
OMAP3 and OMAP4.

Signed-off-by:  Steve Sakoman <steve@sakoman.com>
Acked-by: Nishanth Menon <menon.nishanth@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-08-05 10:11:24 -04:00
Mike Frysinger
793b5726f7 i2c: soft_i2c: add simple GPIO implementation
Since the vast majority of GPIO I2C implementations behave the same way,
support the common GPIO framework with default settings.

This adds two new defines CONFIG_SOFT_I2C_GPIO_{SCL,SDA} so that boards
which want GPIO I2C support need only define these.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Thomas Chou <thomas@wytron.com.tw>
2010-07-22 08:03:47 +02:00
Steve Sakoman
938717cee1 ARMV7: Restructure OMAP i2c driver to allow code sharing between OMAP3 and OMAP4
This patch modifies the omap24xx driver so that it will also work with OMAP4.

Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-07-05 20:00:10 -04:00
Mike Frysinger
b5cebb4fd6 Blackfin: TWI/I2C: implement multibus support
In order to do this cleanly, the register accesses have to be converted to
a C struct (base pointer), so do that in the process.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-05-05 10:04:38 +02:00
Richard Retanubun
26a33504a5 fsl_i2c: Added a callpoint for i2c_board_late_init
This patch adds a callpoint in i2c_init that allows board specific
i2c board initialization (typically for i2c bus reset) that is called
after i2c_init operations, allowing the i2c_board_late_init function
to use the pre-configured i2c bus speed and slave address.
2010-04-19 07:46:35 +02:00
Peter Tyser
61f2b38a17 Replace "#include <asm-$ARCH/$FILE>" with "#include <asm/$FILE>"
The appropriate include/asm-$ARCH directory should already by symlinked
to include/asm so using the whole "asm-$ARCH" path is unnecessary.

This change should also allow us to move the include/asm-$ARCH
directories into their appropriate lib/$ARCH/ directories.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-04-13 09:13:04 +02:00
Stefan Roese
d0b0dcaa22 i2c: Move PPC4xx I2C driver into drivers/i2c directory
This patch moves the PPC4xx specific I2C device driver into the I2C
drivers directory. All 4xx config headers are updated to include this
driver.

Signed-off-by: Stefan Roese <sr@denx.de>
2010-04-06 08:10:41 +02:00
Thomas Weber
5647f78d04 mod change 755 => 644 for multiple files
I executed 'find . -name "*.[chS]" -perm 755 -exec chmod 644 {} \;'

Signed-off-by: Thomas Weber <swirl@gmx.li>
Add some more: neither Makefile nor config.mk need execute permissions.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-03-21 22:22:53 +01:00
Jens Scharsig
0cf0b93161 convert common files to new SoC access
* add's a warning to all files, which need update to new SoC access
 * convert common files in cpu/../at91 and a lot of drivers to use
   c stucture SoC access

Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
2010-02-12 12:31:55 -06:00
Vipin KUMAR
2403f8f417 SPEAr : i2c driver support added for SPEAr SoCs
SPEAr SoCs contain a synopsys i2c controller.
This patch adds the driver for this IP.

Signed-off-by: Vipin <vipin.kumar@st.com>
2010-01-23 08:15:49 -06:00
Prafulla Wadaskar
beca04dd24 Kirkwood: Upgated licencing for files imported from linux source to GPLv2 or later
These are few files directly imported from Linux kernel source.
Those are not modifyed at all ar per strategy.
These files contains source with GPLv2 only
whereas u-boot expects GPLv2 or latter

These files are updated for the same from prior permission from original writes

Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2010-01-23 08:15:48 -06:00
kevin.morfitt@fearnside-systems.co.uk
ac67804fbb Add a unified s3c24x0 header file
This patch adds a unified s3c24x0 cpu header file that selects the header
file for the specific s3c24x0 cpu from the SOC and CPU configs defined in
board config file. This removes the current chain of s3c24-type #ifdef's
from the s3c24x0 code.

Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2009-11-27 16:26:13 -06:00
kevin.morfitt@fearnside-systems.co.uk
492fb1fdbc Move s3c24x0 header files to asm-arm/arch-s3c24x0/
This patch moves the s3c24x0 header files from include/ to
include/asm-arm/arch-s3c24x0/.

checkpatch.pl showed 2 errors and 3 warnings. The 2 errors were both due
to a non-UTF8 character in David M?ller's name:

ERROR: Invalid UTF-8, patch and commit message should be encoded in UTF-8
#489: FILE: include/asm-arm/arch-s3c24x0/s3c2410.h:3:
+ * David M?ller ELSOFT AG Switzerland. d.mueller@elsoft.ch

As David's name correctly contains a non-UTF8 character I haven't fixed
these errors.

The 3 warnings were all because of the use of 'volatile' in s3c24x0.h:

WARNING: Use of volatile is usually wrong: see Documentation/volatile-considered-harmful.txt
#673: FILE: include/asm-arm/arch-s3c24x0/s3c24x0.h:35:
+typedef volatile u8	S3C24X0_REG8;
+typedef volatile u16	S3C24X0_REG16;
+typedef volatile u32	S3C24X0_REG32;

I'll fix these errors in another patch.

Tested by running MAKEALL for ARM8 targets and ensuring there were no new
errors or warnings.

Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2009-11-27 16:26:12 -06:00
Daniel Gorsulowski
4e574c4e2d at91: Extended soft_i2c driver for AT91SAM9263 SoC
While hard_i2c support is not available
(see http://lists.denx.de/pipermail/u-boot/2009-March/049751.html),
this patch enables soft_i2c on AT91SAM9263 SoC.

Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
2009-11-23 09:26:54 +01:00
Dirk Behme
1d2e96de56 OMAP2/3: I2C: Add support for second and third bus
Add support to use second and third I2C bus, too.

Bus 0 is still the default, but by calling i2c_set_bus_num(1/2) before doing
I2C accesses, code can switch to bus 1 and 2, too. Don't forget to switch
back afterwards, then.

Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-11-16 07:25:15 +01:00
Valentin Yakovenkov
08ea550eef new PCA9564 i2c bridge driver
Signed-off-by: Valentin Yakovenkov <yakovenkov@niistt.ru>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-10-30 15:10:58 +01:00
Mike Frysinger
08a1c6258c Blackfin: TWI/I2C: implement bus speed get/set functions
While we're here, improve the speed calculation a bit to match the HRM.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-10-30 15:10:58 +01:00
Mike Frysinger
3814ea4f00 Blackfin: TWI/I2C: add timeout to transfer
The current transfer code relies on ctrlc() to abort transfers, but this
requires user interactivity.  Naturalize the process with a timeout.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-10-30 15:10:58 +01:00
kevin.morfitt@fearnside-systems.co.uk
eb0ae7f549 Clean-up of s3c24x0 drivers excluding nand driver
This patch re-formats the arm920t s3c24x0 driver files, excluding the nand
driver, in preparation for changes to add support for the Embest SBC2440-II Board.

The changes are as follows:
- re-indent the code using Lindent
- make sure register layouts are defined using a C struct
- replace the upper-case typedef'ed C struct names with lower case
  non-typedef'ed ones
- make sure registers are accessed using the proper accessor functions
- run checkpatch.pl and fix any error reports

It assumes the following patch has been applied first:
- [U-Boot][PATCH-ARM] CONFIG_SYS_HZ fix for ARM902T S3C24X0 Boards, 05/09/2009
- patches 1/4 and 2/4 of this series

Tested on an Embest SBC2440-II Board with local u-boot patches as I don't have
any s3c2400 or s3c2410 boards but need this patch applying before I can submit
patches for the SBC2440-II Board. Also, temporarily modified sbc2410x, smdk2400,
smdk2410 and trab configs to use the mtd nand driver (which isn't used by any
board at the moment), ran MAKEALL for all ARM9 targets and no new warnings or
errors were found.

Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2009-10-13 21:13:56 -05:00
Joakim Tjernlund
d1c9e5b379 fsl_i2c: Do not generate STOP after read.
__i2c_read always ends with a STOP condition thereby releasing
the bus. It is cleaner to do the STOP magic in i2c_read(), like
i2c_write() does. This may also help future multimaster systems which
wants to hold on to the bus until all transactions are finished.

Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
2009-09-28 07:35:56 +02:00
Joakim Tjernlund
9940420212 fsl_i2c: Impl. AN2919, rev 5 to calculate FDR/DFSR
The latest AN2919 has changed the way FDR/DFSR should be calculated.
Update the driver according to spec. However, Condition 2
is not accounted for as it is not clear how to do so.

Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
2009-09-28 07:35:54 +02:00
Joakim Tjernlund
d01ee4db93 fsl_i2c: Add CONFIG_FSL_I2C_CUSTOM_{DFSR/FDR}
Some boards need a higher DFSR value than the spec currently
recommends so give these boards the means to define there own.

For completeness, add CONFIG_FSL_I2C_CUSTOM_FDR too.

Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
2009-09-28 07:35:53 +02:00
Joakim Tjernlund
21f4cbb772 fsl_i2c: Wait for STOP condition to propagate
After issuing a STOP one must wait until the STOP has completed
on the bus before doing something new to the controller.

Also add an extra read of SR as the manual mentions doing that
is a good idea.

Remove surplus write of CR just before a write, isn't required and
could potentially disturb the I2C bus.

Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
2009-09-28 07:35:52 +02:00
Timur Tabi
92477a631b fsl_i2c: increase I2C timeout values and make them configurable
The value of I2C_TIMEOUT in fsl_i2c.c has several problems.  First, it is
defined as CONFIG_HZ/4, but it is used as a count of microseconds, so it makes
no sense to derive it from a clock rate.  Second, the current value (250) is
too low for some boards, so it needs to be increased.  Third, the timeout
necessary for multiple-master arbitration is larger than the timeout for basic
read/write operations, so we shouldn't have a single constant for both timeouts.
Finally, it would be nice if we could override these values on a per-board
basis.

Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Tested-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Peter Tyser <ptyser@xes-inc.com>
2009-09-06 11:26:05 +02:00
Wolfgang Denk
53cc18c71b Minor coding style cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-08-10 10:38:34 +02:00
Tom Rix
7f79dfb48b OMAP I2C Fix the sampling clock.
This problem is seen on Zoom1 and Zoom2 in the startup and
when i2c probe is used

Before :

In:    serial
Out:   serial
Err:   serial
timed out in wait_for_bb: I2C_STAT=1000
timed out in wait_for_bb: I2C_STAT=1000
timed out in wait_for_bb: I2C_STAT=1000
timed out in wait_for_pin: I2C_STAT=1000
I2C read: I/O error
timed out in wait_for_bb: I2C_STAT=1000
timed out in wait_for_bb: I2C_STAT=1000
Die ID #327c00020000000004013ddd05026013
Hit any key to stop autoboot:  0
OMAP3 Zoom1# i2c probe
Valid chip addresses:timed out in wait_for_bb: I2C_STAT=1000
 02 03 04 05 06 07 08 09 0A 0B 0C 0D <snip>

After :

In:    serial
Out:   serial
Err:   serial
Die ID #327c00020000000004013ddd05026013
Hit any key to stop autoboot:  0
OMAP3 Zoom1# i2c probe
Valid chip addresses: 48 49 4A 4B

The addresses are for the twl4030.

The prescalar that converts the function clock to the sampling
clock is hardcoded to 0.  The reference manual recommends 7
if the function clock is 96MHz.

Instead of just changing the hardcoded values, the prescalar
is calculated from the value I2C_IP_CLK.

The i2c #defines are in kHz.  The speed passed into the
i2c init routine is in Hz.  To be consistent, change the
defines to be in Hz.

The timing calculations are based on what is done in the
linux 2.6.30 kernel in drivers/i2c/buses/i2c_omap.c as
apposed to what is done in TRM.

The major variables in the timing caculations are
specified as #defines that can be overriden as required.

The variables and their defaults are

I2C_IP_CLK				SYSTEM_CLOCK_96
I2C_INTERNAL_SAMPLING_CLK		19200000
I2C_FASTSPEED_SCLL_TRIM			6
I2C_FASTSPEED_SCLH_TRIM			6
I2C_HIGHSPEED_PHASE_ONE_SCLL_TRIM	I2C_FASTSPEED_SCLL_TRIM
I2C_HIGHSPEED_PHASE_ONE_SCLH_TRIM	I2C_FASTSPEED_SCLH_TRIM
I2C_HIGHSPEED_PHASE_TWO_SCLL_TRIM	I2C_FASTSPEED_SCLL_TRIM
I2C_HIGHSPEED_PHASE_TWO_SCLH		I2C_FASTSPEED_SCLH_TRIM

This was runtime verified on Zoom1, Zoom2, Beagle and Overo.
The 400kHz and 3.4M cases were verifed on test Zoom1,
Zoom2, Beagle and Overo configurations.

Testing for omap2 will be done in a second step as Nishanth
and Jean-Christophe commented.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
2009-07-28 08:52:33 +02:00
Heiko Schocher
4ce5a72851 arm, i2c: added support for the TWSI I2C Interface
Signed-off-by: Heiko Schocher <hs@denx.de>
2009-07-28 08:20:58 +02:00
Heiko Schocher
39df00d9ae i2c, mpc83xx: add CONFIG_SYS_I2C_INIT_BOARD for fsl_i2c
This patch adds the possibility to call a board specific
i2c bus reset routine for the fsl_i2c bus driver, and adds
this option for the keymile kmeter1 board.

The deblock sequence for this board is implemented and
tested in the following way:

CR = 0x20 (release SDA and SCL pin)
CR = 0xa0 (start read)
dummy read
dummy read
if 2. dummy read == 0x00
	3. dummy read

CR = 0x80 (SDA and SCL now 1 SR = 0x86)
CR = 0x00 (Modul reset SR=0x81)
CR = 0x80 (SDA and SCL = 1, SR = 0x81)

Signed-off-by: Heiko Schocher <hs@denx.de>
2009-07-21 07:06:26 +02:00
Peter Meerwald
98ab14e858 Blackfin: TWI/I2C: fix pure writes
If doing a pure write with register address and data (not a read/write
combo transfer), we don't set the initial transfer length properly which
ends up causing only the register address to be transferred.

While we're here, fix the i2c_write() parameter description of the buffer.

Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-30 08:27:45 +02:00
Peter Tyser
0f89c54be9 i2c: Update references to individual i2c commands
The individual i2c commands imd, imm, inm, imw, icrc32, iprobe, iloop,
and isdram are no longer available so all references to them have been
updated to the new form of "i2c <cmd>".

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-06-12 20:39:46 +02:00
Peter Tyser
655b34a78a i2c: Create common default i2c_[set|get]_bus_speed() functions
New default, weak i2c_get_bus_speed() and i2c_set_bus_speed() functions
replace a number of architecture-specific implementations.

Also, providing default functions will allow all boards to enable
CONFIG_I2C_CMD_TREE.  This was previously not possible since the
tree-form of the i2c command provides the ability to display and modify
the i2c bus speed which requires i2c_[set|get]_bus_speed() to be
present.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-06-12 20:39:45 +02:00
Peter Tyser
f0722ee762 tsi108_i2c: Add i2c_init() stub function
Add the i2c_init() function so that the tsi108_i2c.c driver fits
U-Boot's standard I2C API which is utilized by cmd_i2c.c

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-06-12 20:39:45 +02:00
Wolfgang Denk
dfc91c3395 Merge branch 'master' of git://git.denx.de/u-boot-arm 2009-04-02 00:24:33 +02:00
Jens Scharsig
d144f94d59 soft_i2c.c compiler/linker error
This patch fix the compiler/linker errors

common/cmd_i2c.c:1252: undefined reference to `i2c_get_bus_speed'
common/cmd_i2c.c:1256: undefined reference to `i2c_set_bus_speed'

if board use CONFIG_I2C_CMD_TREE and CONFIG_I2C_MULTI_BUS is not
uesd/undef (wrong define order)

and

removes additional empty lines

Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
2009-03-31 08:29:50 +02:00
Jean-Christophe PLAGNIOL-VILLARD
d3b6357741 s3c24x0: move i2c driver to drivers/i2c
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-30 18:58:40 +02:00
Jean-Christophe PLAGNIOL-VILLARD
942ba9969b davinci: move i2c driver to drivers/i2c
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-30 18:58:39 +02:00
Jean-Christophe PLAGNIOL-VILLARD
50f601cca8 s3c44b0: move i2c driver to drivers/i2c
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-29 23:01:40 +02:00
Heiko Schocher
1b6275dfb1 8xx: add support for new keymile kmsupx4 board.
This patch adds support for the kmsupx4 board from Keymile,
based on a Freescale MPC852T CPU

- serial console on SMC1
- 32 MB SDRAM
- 32 MB NOR Flash
- Ethernet over SCC3
- I2C Bitbang

Signed-off-by: Heiko Schocher <hs@denx.de>
2009-03-18 20:50:05 +01:00
Heiko Schocher
c1bce4fff7 83xx, i2c: add mux support for fsl_i2c
This patch adds I2C mux support for the fsl_i2c driver. This
allows you to add "new" i2c busses, which are reached over
i2c muxes. For more infos, please look in the README and
search for CONFIG_I2C_MUX.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-03-05 18:21:17 -06:00
Guennadi Liakhovetski
e7de18afe8 i.MX31: Start the I2C clock on driver initialisation
i.MX31 powers on with most clocks running, so, after a power on this explicit
clock start up is not required. However, as Linux boots it disables most clocks
to save power. This includes the I2C clock. If we then soft reboot from Linux
the I2C clock stays off. This breaks the phycore, which has its environment in
I2C EEPROM. Fix the problem by explicitly starting the clock in I2C driver
initialisation routine.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Ack-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-14 10:00:51 +01:00
Wolfgang Denk
6c6e042ab3 Merge branch 'master' of git://git.denx.de/u-boot-arm 2009-02-01 21:38:07 +01:00
Mike Frysinger
be853bf86b Blackfin: overhaul i2c driver
The current Blackfin i2c driver does not work properly with certain devices
due to it breaking up transfers incorrectly.  This is a rewrite of the
driver and relocates it to the newer place in the source tree.

Also remove duplicated I2C speed defines in Blackfin board configs and
disable I2C slave address usage since it isn't implemented.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28 13:26:13 -05:00
Andrew Dyer
2ac6985a74 soft_i2c.c add option for repeated start in i2c_read()
This patch adds a #define to optionally change the behaviour of
i2c_read() in soft_i2c.c to send an I2C repeated start instead of a
stop-start between sending the device address pointer write and
reading back the data.  The current behaviour is retained as the
default.

While most devices will work either way, I have a smart battery(*)
that requires repeated start, and someone at some point found a
device that required a stop-start.

(*) http://www.inspired-energy.com/Standard_Products/NL2054/NL2054%20Rev1.0%20Data%20Sheet.pdf

Signed-off-by: Andrew Dyer <adyer@righthandtech.com>
2009-01-27 22:26:31 +01:00
Dirk Behme
7d264c1ef2 OMAP3: Add I2C support
Add I2C support.

Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-01-24 17:51:22 +01:00
Wolfgang Denk
455ae7e87f Coding style cleanup, update CHANGELOG.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-12-16 01:02:17 +01:00
Timur Tabi
ecf5f077c8 i2c: merge all i2c_reg_read() and i2c_reg_write() into inline functions
All implementations of the functions i2c_reg_read() and
i2c_reg_write() are identical. We can save space and simplify the
code by converting these functions into inlines and putting them in
i2c.h.

Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-By: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-12-15 23:46:21 +01:00
Trent Piepho
5e3ab68e9a Section name should be ".data", not "data"
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-12-09 00:48:41 +01:00
Dirk Behme
e23c7c95a9 ARM: OMAP: Convert IO macros
Convert IO macros to readx/writex.

Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
2008-11-21 01:44:35 +01:00
Wolfgang Denk
8ed44d91c8 Cleanup: fix "MHz" spelling
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-10-21 11:25:39 +02:00
Heiko Schocher
a21ca95f8b mgsuvd: fix compiler warning when using soft_i2c driver
Signed-off-by: Heiko Schocher <hs@denx.de>
2008-10-18 21:54:04 +02:00
Jean-Christophe PLAGNIOL-VILLARD
6d0f6bcf33 rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-10-18 21:54:03 +02:00
Heiko Schocher
67b23a3228 I2C: adding new "i2c bus" Command to the I2C Subsystem.
With this Command it is possible to add new I2C Busses,
which are behind 1 .. n I2C Muxes. Details see README.

Signed-off-by: Heiko Schocher <hs@denx.de>
2008-10-18 21:54:02 +02:00
Heiko Schocher
4ca107effe soft_i2c: Add CFG_I2C_INIT_BOARD option
This patch adds the option for a boardspecific
I2C deblocking mechanism for the soft i2c driver.

Signed-off-by: Heiko Schocher <hs@denx.de>
2008-10-18 21:54:02 +02:00
Heiko Schocher
98aed37958 soft_i2c: prevent compiler warnings if driver does not use CPU Pins.
This patch fixes the following warnings, when using
the soft_i2c driver using no CPU pins on MPC82xx or MPC8xx
systems:

soft_i2c.c: In function 'send_reset':
soft_i2c.c:93: warning: unused variable 'immr'
soft_i2c.c: In function 'send_start':
soft_i2c.c:124: warning: unused variable 'immr'
soft_i2c.c: In function 'send_stop':
soft_i2c.c:146: warning: unused variable 'immr'
soft_i2c.c: In function 'send_ack':
soft_i2c.c:171: warning: unused variable 'immr'
soft_i2c.c: In function 'write_byte':
soft_i2c.c:196: warning: unused variable 'immr'
soft_i2c.c: In function 'read_byte':
soft_i2c.c:244: warning: unused variable 'immr'

Signed-off-by: Heiko Schocher <hs@denx.de>
2008-10-18 21:54:01 +02:00
Heiko Schocher
799b784aa0 i2c: add CONFIG_I2C_MULTI_BUS for soft_i2c and mpc8260 i2c driver.
Signed-off-by: Heiko Schocher <hs@denx.de>
2008-10-18 21:54:01 +02:00
Wolfgang Denk
e99e9575bb Merge branch 'Makefile' of git://git.denx.de/u-boot-arm 2008-09-01 00:16:29 +02:00
Jean-Christophe PLAGNIOL-VILLARD
4d75e0aa9c soft_i2c: move to drivers/i2c
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-29 12:25:02 +02:00
TsiChung Liew
5d9a5efa4b Add I2C frequency dividers for ColdFire
The existing I2C freqency dividers for FDR does not apply
to ColdFire platforms; thus, a seperate table is added
based on MCF5xxx Reference Manual

Signed-off-by: Luigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com>
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Acked-by: Tabi Timur <timur@freescale.com>
2008-08-28 09:16:54 -06:00
Michal Simek
a4a549b4b5 i2c: Clean drivers/i2c/ Makefile
Signed-off-by: Michal Simek <monstr@monstr.eu>
2008-08-18 23:24:01 +02:00
Stefan Roese
f2302d4430 Fix merge problems
Signed-off-by: Stefan Roese <sr@denx.de>
2008-08-06 14:05:38 +02:00
Wolfgang Denk
53677ef18e Big white-space cleanup.
This commit gets rid of a huge amount of silly white-space issues.
Especially, all sequences of SPACEs followed by TAB characters get
removed (unless they appear in print statements).

Also remove all embedded "vim:" and "vi:" statements which hide
indentation problems.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-05-21 00:14:08 +02:00
Kumar Gala
3e3f766a52 Fix warnings introduced by I2C bus speed setting patch
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-04-13 14:54:16 -07:00
Sascha Hauer
cdace06612 add an i2c driver for mx31
This patch adds an i2c driver for Freescale i.MX processors

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-04-13 14:21:43 -07:00
Wolfgang Denk
950a392464 Revert merge of git://www.denx.de/git/u-boot-arm, commit 62479b18:
Reverting became necessary after it turned out that the patches in
the u-boot-arm repo were modified, and in some cases corrupted.

This reverts the following commits:

	066bebd635
	7a837b7310
	c88ae20580
	a147e56f03
	d6674e0e2a
	8c8463cce4
	c98b47ad24
	8bf69d8178
	8c16cb0d3b
	a574a73852
	1377b5583a
	1704dc2091

Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-04-11 15:11:26 +02:00
Sascha Hauer
8c8463cce4 add an i2c driver for mx31
This patch adds an i2c driver for Freescale i.MX processors

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-03-30 11:32:16 +01:00
Timur Tabi
d8c82db482 Add support for setting the I2C bus speed in fsl_i2c.c
Add support to the Freescale I2C driver (fsl_i2c.c) for setting and querying
the I2C bus speed.  Current 8[356]xx boards define the CFG_I2C_SPEED macro,
but fsl_i2c.c ignores it and uses conservative value when programming the
I2C bus speed.

Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
2008-03-27 00:09:17 +01:00
Jean-Christophe PLAGNIOL-VILLARD
080c646dbf drivers/i2c : move i2c drivers to drivers/i2c
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2007-11-20 20:14:18 +01:00