Enable CONFIG_SYS_I2C_ZYNQ only if it has either I2C0 or I2C1
enabled in a board config.This fixes the issue of i2c error
during board init if board specific doesnt have either I2C0
or I2C1.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This adds support to update firmware on qspi flash using DFU.
On device:
=> setenv dfu_alt_info ${dfu_alt_info_qspi}
=> dfu 0 sf 0:0
On host:
$ sudo dfu-util -l
$ sudo dfu-util -D MLO -a MLO
$ sudo dfu-util -D u-boot.img -a u-boot.img
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On T1040D4RDB board, u-boot fails to connect port FM1@DTSEC3 to
the Ethernet PHY because the wrong PHY address is used. Also,
T1040D4RDB supports SGMII on one port only.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This commit adds additional file with implementation of board
detection code for Odroid-XU3/XU4.
The detection depends on compatible found in fdt:
- "samsung,exynos5" - uses Exynos5 generic code
- "samsung,odroidxu3" - try detect XU3 revision
There are few revisions of Odroid XU3/XU4, each can be detected
by checking the value of channel 9 of built-in ADC:
Rev ADC Board
0.1 0 XU3 0.1
0.2 372 XU3 0.2 | XU3L - no DISPLAYPORT
0.3 1280 XU4 0.1
The detection code depends on the ADC+10% value.
Implementation of functions:
- set_board_type() - read ADC and set type
- get_board_rev() - returns board revision: 1..3
- get_board_type() - returns board type string
Additional functions with return values of bool:
- board_is_generic() - true if found compatible "samsung,exynos5"
but not "samsung,odroidxu3"
- board_is_odroidxu3() - true if found compatible "samsung,odroidxu3"
and one of XU3 revision.
- board_is_odroidxu4() - true if found compatible "samsung,odroidxu3"
and XU4 revision.
After I2C controller init, the get_board_type() can check
if the XU3 board is a "Lite" variant, by probing chip
0x40 on I2C0 (INA231 - exists only on non-lite).
This is useful for setting fdt file name at misc_init_r().
Enabled configs:
- CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
- CONFIG_ODROID_REV_AIN
- CONFIG_REVISION_TAG
- CONFIG_BOARD_TYPES
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
As sama5 board has 32k sram size, so the at91bootstrap and spl for sama5
boards is bigger than 16k (0x4000). That will overlap the U-Boot
environment. So I move environment to 0x6000. And reduce its size as
well.
Following shows the size of the spl binaries (v2015.04 vs v2015.07):
% ls v2015.04/*spi*spl.bin -l | awk '{print $5,$(NF)}'
15540 v2015.04/at91sam9n12ek_spiflash_defconfig_u-boot-spl.bin
15704 v2015.04/at91sam9x5ek_spiflash_defconfig_u-boot-spl.bin
16064 v2015.04/sama5d3xek_spiflash_defconfig_u-boot-spl.bin
16304 v2015.04/sama5d4ek_spiflash_defconfig_u-boot-spl.bin
16304 v2015.04/sama5d4_xplained_spiflash_defconfig_u-boot-spl.bin
% ls v2015.07/*spi*spl.bin -l | awk '{print $5,$(NF)}'
16136 v2015.07/at91sam9n12ek_spiflash_defconfig_u-boot-spl.bin
16300 v2015.07/at91sam9x5ek_spiflash_defconfig_u-boot-spl.bin
16664 v2015.07/sama5d3xek_spiflash_defconfig_u-boot-spl.bin
16904 v2015.07/sama5d4ek_spiflash_defconfig_u-boot-spl.bin
16904 v2015.07/sama5d4_xplained_spiflash_defconfig_u-boot-spl.bin
The gcc version is: gcc 4.7.3 (Ubuntu/Linaro 4.7.3-12ubuntu1)
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Bo Shen <voice.shen@gmail.com>
As more features are added for SD boot on LS1021A QDS board,
the size of U-Boot is larger. CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS
needs to be adjusted to a suitable value.
Starting address of the malloc pool used in SPL needs to be
adjusted too, or it will occupy the address u-boot loads.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
I2C1 can work on ls102xa rev2.0 SD boot, so add
ID EEPROM for SD boot.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Rework unified section macro select via Kconfig option
instead of macro definition in mx7_common header file.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Add i.MX6DQP-Sabresd board support:
1. set fdt_file according to board_rev which is set at runtime.
2. Add mx6dqp_ddr_ioregs and calibration value for this board.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
This macro is not needed, since gd->ram_size is assigned value using
function imx_ddr_size().
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Linux only boots IMX.51-based boards with device tree, so this board
would benefit from supporting it.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Cc: Stefano Babic <sbabic@denx.de>
As 3G/1G user/kernel memory split is used on LS1021A, the Linux kernel
fails to access the device tree blob on boot. The reason is that u-boot
relocates the device tree blob into high memory when booting the kernel
and the kernel is unable to access the blob.
To avoid this issue, fdt_high is set to the value of 0xffffffff. The
device tree blob will not get relocated and is still in low memory to
make it accessible to the kernel.
For the same reason, initrd_high is set to the value of 0xffffffff too.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
After the secondary cores enter U-Boot, use CONFIG_ARMV8_MULTIENTRY to
make secondary cores excute in spin loop.
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds esdhc support for ls1043ardb.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LS1043ARDB Specification:
-------------------------
Memory subsystem:
* 2GByte DDR4 SDRAM (32bit bus)
* 128 Mbyte NOR flash single-chip memory
* 512 Mbyte NAND flash
* 16 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
Ethernet:
* XFI 10G port
* QSGMII with 4x 1G ports
* Two RGMII ports
PCIe:
* PCIe2 (Lanes C) to mini-PCIe slot
* PCIe3 (Lanes D) to PCIe slot
USB 3.0: two super speed USB 3.0 type A ports
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
There are two LS series processors are built on ARMv8 Layersacpe
architecture currently, LS2085A and LS1043A. They are based on
ARMv8 core although use different chassis, so create fsl-layerscape
to refactor the common code for the LS series processors which also
paves the way for adding LS1043A platform.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Config Security Level Register is different between different SoCs,
so put the CSL register definition into the arch specific directory.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For most PPC platforms, they will call the first get_clocks() in
init_sequence_f[] as they define CONFIG_PPC. CONFIG_SYS_FSL_CLK is
then defined to call the second get_clocks(), which should be
redundant for PPC.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This board has not compiled for me for quite some time due to size
constraints, remove.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This board has not compiled for me for quite some time due to size
constraints, remove.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This board has not compiled for me for quite some time due to size
constraints, remove.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This board has not compiled for me for quite some time due to size
constraints, remove.
Cc: John Otken <jotken@softadvances.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
As QSPI and IFC are pin-multiplexed on LS1021A, only IFC is supported in
SD boot now. For the customer's demand, QSPI needs to be supported in SD
boot too.
This patch adds QSPI or IFC support in SD boot according to the
corresponding defconfig. For detail, ls1021atwr_sdcard_ifc_defconfig is
used to support IFC in SD boot and ls1021atwr_sdcard_qspi_defconfig is
used to support QSPI in SD boot.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This will allow OF-based earlycon to be used once the appropriate
aliases are added to the device tree and kernel support is fixed.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Define CONFIG_SYS_SPI_ARGS_OFFS, CONFIG_SYS_SPI_ARGS_SIZE
and CONFIG_SYS_SPI_KERNEL_OFFS which will be used in SPL
spi mode. These macros defines the device tree offset, size
and the kernel image offset in flash respectively.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
This patch enabled CONFIG_SPI_FLASH_ISSI for qspi on zynq boards.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Enabled SPI flash Bank/Extended address register support.
Bank/Extended address registers are used to access the flash
which has size > 16MiB in 3-byte addressing.
Signed-off-by: Jagan Teki <jteki@openedev.com>
This patch adds support for zynq qspi controller driver
on zynq-common.h
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Jagan Teki <jteki@openedev.com>
We have finished Generic Board conversion for ARM and PowerPC, i.e.
all the boards have been converted except OpenRISC, SuperH, SPARC,
which have not supported Generic Board framework yet.
Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro
defines in include/configs/*.h.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG support and enable it to set
'board_rev' and 'board_name' envs.
'board_rev' can be used in scripts to determine what board we are running on
and 'board_name' for pretty printing.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Convert altera_tse to driver model and phylib.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert altera sysid to driver model with misc uclass.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert altera_pio to driver model.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert altera_uart to driver model.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Convert altera_jtag_uart to driver model.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move the timer code from interrupts.c into timer.c . Eliminate the
installation of timer interrupt handler, which is no longer used.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Zap almost all of the ad-hoc timer code from interrupts.c and
use the code in lib/time.c instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
As altera_pio_init() uses BSS, it should be moved to
board_early_init_r().
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Marek Vasut <marex@denx.de>
This patch moves command line configuration from board header
file to board defconfig in the way of Kconfig. The change passed
savedefconfig.
This fixes warnings such as : "CONFIG_SYS_HUSH_PARSER" redefined,
when "Use hush shell" is selected with menuconfig, etc.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Since spl doesn't support DM currently, do not define DM_MMC
for spl build.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add clock information for Galileo
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
If CONFIG_SYS_MALLOC_F_LEN is enabled, the stack is moved down to the
specified size to make the malloc function available before relocation.
But on keystone platforms SYS_SPL_MALLOC is immediately preceding stack,
which is causing an overlap with this config enabled.
So leave a gap between malloc space and stack space.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Since usb ether gadget doesn't have support for driver model, so
not defining usb ether gadget when ethernet driver model is
defined.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for distro bootcmds and network booting while retaining
backwards compatibility with the current "legacy" setup. With these
changes the default boot sequence becomes:
* SD card (standard distro boot)
* SD card (legacy boot)
* EMMC (standard distro boot)
* EMMC (legacy boot)
* Nand (legacy boot)
* PXE (standard distro boot)
* DHCP (standard distro boot)
The older boot scripts have some overlap with what the distro
bootcommands to however i've left them unchanged to prevent introduction
of subtle bugs.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Add mandatory address variables for loading scripts and pxe configuration as
per README.distro
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Advantech SOM-6896 is a Broadwell U based COM Express Compact Module
Type 6. This patch adds support for it as a coreboot payload.
On board SATA and SPI are functional. On board Ethernet isn't functional
but since it's optional and ties up a PCIe x4 that is otherwise brought
out, this isn't a concern at the moment. USB doesn't work since the
xHCI driver appears to be broken.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
CONFIG_HOSTNAME is an environment varible, so that quotation mark
is not needed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a Kconfig option to disable the Integrated Graphics Device (IGD)
so that it does not show in the PCI configuration space as a VGA
disaplay controller. This gives a chance for U-Boot to run PCI/PCIe
based graphics card's VGA BIOS and use that for the graphics console.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch enables DM_SERIAL for all ARCH_MVEBU boards (AXP & A38x).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch enables DM_USB on the Marvell AXP / A38x eval boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Luka Perkov <luka.perkov@sartura.hr>
When running on the AXP I sometimes noticed a strange behavior. As some
characters are not echoed on the U-Boot prompt. Not disabling the
lowlevel_init code, especially calling cpu_init_cp15() in the main
U-Boot seems to solve this issue.
Signed-off-by: Stefan Roese <sr@denx.de>
Not all sunxi boards have an MMC embedded. Switching to the Kconfig option
will allow to enable or disable the support in each boards' defconfig.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
When using the fastboot boot command, the image sent to U-Boot will be an
Android boot image. If the support is missing, that obviously won't work,
so we need it in our configuration.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add a bootcmd_sunxi_compat value to the default environment when building
with CONFIG_OLD_SUNXI_KERNEL_COMPAT, this way people who occasionally want
to boot an old kernel can do so by simply typing "run bootcmd_sunxi_compat"
rather then needing to have 2 separate setups / sdcards for old and
new kernels.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
common/dlmalloc.c is quite big, both in .text and .data usage. E.g. for a
Mele_M9 sun6i board build this reduces .text from 0x4214 to 0x3b94 bytes,
and .data from 0x54c to 0x144 bytes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Tom Rini <trini@konsulko.com>
Select CONFIG_SPL_STACK_R for sunxi boards, this gives us much more
room on the stack once we've the DRAM running.
Besides being a good change to have on itself, this also paves the
way for switching to using malloc_simple in the SPL which cuts of
close to 4KiB of the SPL size.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Between v2015.07-rc1 and v2015.07-rc2 this board started
silent boot failure. A bisect led to commit 6eed3786c6
("net: Move the CMD_NET config to defconfigs"). This commit
looks harmless in itself, but it did implicitly add a feature
to the image which led to this:
u-boot$git describe 6eed3786c6
v2015.07-rc1-412-g6eed3786c68c
^^^
u-boot$ls -l ../41*/u-boot.bin
-rwxrwxr-x 1 paul paul 261476 Oct 16 16:47 ../411/u-boot.bin
-rwxrwxr-x 1 paul paul 266392 Oct 16 16:43 ../412/u-boot.bin
u-boot$bc
bc 1.06.95
Copyright 1991-1994, 1997, 1998, 2000, 2004, 2006 Free Software Foundation, Inc.
This is free software with ABSOLUTELY NO WARRANTY.
For details type `warranty'.
256*1024
262144
i.e. we finally broke through the 256k monitor size. Jump it
up to 384k and fix the hard coded value used in the env offset
at the same time.
We were probably flirting with the 256k size issue without
knowing it when testing on different baselines in earlier
commits, but since this is all board specific, a rebase or
reorder to put this commit 1st is of little value.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
When debugging an env fail due to too small a malloc pool, it
was noted that the env write was 256k. But the device sector
size is 1/2 that, as can be seen from "fli" output:
Bank # 1: CFI conformant flash (16 x 16) Size: 16 MB in 131 Sectors
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x1888
Erase timeout: 4096 ms, write timeout: 1 ms
Buffer write timeout: 2 ms, buffer size: 64 bytes
Sector Start Addresses:
FF000000 E RO FF020000 E RO FF040000 E RO FF060000 E RO FF080000 E RO
FF0A0000 E RO FF0C0000 E RO FF0E0000 E RO FF100000 E RO FF120000 E RO
[...]
FFF00000 RO FFF20000 RO FFF40000 RO FFF60000 RO FFF80000 RO
FFFA0000 RO FFFC0000 RO FFFE0000 E RO FFFE8000 RO FFFF0000 E RO
FFFF8000 RO
=>
The desired env sector is FFF40000->FFF60000, or 0x20000 in length,
just after the 256k u-boot image which starts @ FFF00000.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Currently the board fails to save its env, since the env size
is much smaller than the sector size, and the malloc fails for
the pad buffer, giving the user visible symptom of:
Unable to save the rest of sector (253952)
Allow for 1M malloc pool, the same as used on the sbc8548 board.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Used NAND chips requires at least 4-bit error correction, so use BCH8
as it is what kernel uses.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Javier Martinez Canillas <javier@osg.samsung.com>
Juno comes with 8GB RAM, but U-Boot only passes 2GB to the kernel.
Declare a secondary memory bank and set the sizes correctly.
Signed-off-by: Liviu Dudau <Liviu.Dudau@foss.arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
The default dockstar configuration for U-Boot currently causes it to
overrun the environment area, so that a "saveenv" command bricks the
device. This patch moves the environment to a higher address to avoid
that.
Signed-off-by: Eric Cooper <ecc@cmu.edu>
Currently, the device tree relocation is disabled, likely to
keep some DDR3 RAM at the end for Cortex-M4 firmwares. This
can be archived using bootm_size, which limits the image
processing range of the boot commands.
Move the device tree standard load address to a higher address
which aligns better with what we are doing on other boards.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Replace 'fatload' command by 'load', to be able to use EXT*
partitions while keeping FAT partition compatibility.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Tested-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
MTD partitioning in current pcm052 configuration is inconsistent.
Fix it across MTDPARTS_DEFAULT, CONFIG_EXTRA_ENV_SETTINGS, and
CONFIG_ENV_OFFSET[_REDUND].
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
We run 4 Arndale boards in our automated test framework, they have
been running quite happily for quite some time using a Debian Wheezy
userspace.
However when upgrading to a Debian Jessie we started seeing frequent
segmentation faults from gcc when building the kernel, to the extent
that it is unable to successfully build the kernel twice in a row, and
often fails on the first attempt.
Searching around I found https://bugs.launchpad.net/arndale/+bug/1081417
which pointed towards http://www.spinics.net/lists/kvm-arm/msg03723.html
and CPU Errata 773022 and 774769.
This errata needs to be applied to all processors in an SMP system,
meaning that the usual strategy of applying them in
arch/arm/cpu/armv7/start.S is not appropriate (since that applies to
the boot processor only). Instead we apply these errata in the secure
monitor which is code that is traversed by all processors as they are
brought up.
The net affect on Arndale is that ACTLR changes from 0x40 to
0x2000042. I ran 17 kernel compile iterations overnight with no
segfaults.
Runtime testing was done on our v2014.10 based branch and forward
ported (with only minimal and trivial contextual conflicts) to current
master, where it has been build tested only.
I suppose in theory these errata apply to any Exynos5250 based boards,
but Arndale is the only one I have access to and I have therefore
chosen to be conservative and only apply it there.
Also, reorder CONFIG_ARM_ERRATA_794072 in README to make the list
numerically sorted.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
This platform has not gone into production. So lets remove it.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Add CONFIG_SYS_GENERIC_BOARD to lwmon5.h and CONFIG_DISPLAY_BOARDINFO
to Kconfig file.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
This reverts commit 8fe11b8901.
I'll add support to lwmon5 in the next patch and will remove
support for the broken lcd4_lwmon5 as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
CONFIG_TWL4030_POWER is a boolean define variable. It is either defined
or not defined and should not have a value assigned to it.
Remove the value.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
This patch changes the default "root=" parameter to "/dev/sda2".
Many linux based distros use /dev/sda1 for their boot partition; this is
often not a rootfs that can be used by the "root=" parameter.
Linaro images use /dev/sda1 as a boot partition, although this of a
different nature to a distro image. Linaro uses /dev/sda2 for the rootfs
partition.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The latest Juno firmware stores the files in NOR flash as "norkern" for
kernel binary, "board.dtb" for the device tree binary.
The "old" firmware used the name "Image" for the kernel binary and
"juno" for the device tree binary.
Rather than just change the default U-Boot configuration to use the new
names, breaking users with the old firmware, attempt to load the default
filename first. If that fails, attempt to load the alternate filename.
I've echo'd that we are loading the alternate file to counter the
output from "afs load" shown if the first load attempt fails. For
example, I see output like this on my Juno board when it's configured
the with the "old" firmware:
image "norkern" not found in flash
Loading Image instead of norkern
loaded region 0 from 08500000 to 80000000, 00AB6318 bytes
image "board.dtb" not found in flash
Loading juno instead of board.dtb
loaded region 0 from 0A000000 to 83000000, 00003188 bytes
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Some OS images require an initrd on Juno.
If the file ramdisk.img exists in NOR flash, then we load it and pass
the address to the kernel. Otherwise, we pass the "-" parameter as
before.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Linaro's Juno Android builds requires the androidboot.hardware parameter
be set to a know board name.
Non-Android kernels ignore this extra parameter because they don't
contain code to parse it.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Create an additional FVP configuration to boot images pre-loaded into
DRAM.
Sometimes it's preferential to boot the model by loading the files
directly into DRAM via model parameters, rather than using
SemiHosting.
An example of model parmaters that are used to pre-load the files
into DRAM:
--data cluster0.cpu0=Image@0x80080000 \
--data cluster0.cpu0=fvp-base-gicv2-psci.dtb@0x83000000 \
--data cluster0.cpu0=uInitrd@0x84000000
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[trini: Update board/armltd/vexpress64/Kconfig logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
vexpress64 kernels are usually over 8 MBytes in length, so setting the
max uImage length to 64 Mbytes should give us plenty of scope for
expansion.
I mostly chose this length to match other board configs that use
"(64 << 20)".
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes a couple of checkpatch warnings on the vexpress64 config.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The size allocation for SPL is increased in all cases to match the
already-expanded value used on Tegra124. This is both for general
consistency, and because the seaboard build trips over the limit already
when using one of the ARM compilers packaged with 14.04. For the record,
when building Seaboard:
arm-linux-gnueabi- SPL is too big by 0x36 bytes
arm-linux-gnueabihf- SPL fits by 0x2a bytes
arm-none-eabi- SPL fits by 0xa bytes
(Those figures are from builds with the expanded SPL size allocation,
relative to the non-expanded SPL size limit; they're better by about
6 bytes in the more constrained build.)
Fixes: ba52199422 ("tegra124: Expand SPL space by 8KB")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add DFU support.
Tested by flashing SPL and u-boot.img into SPI NOR flash with the
following commands:
=> setenv dfu_alt_info ${dfu_alt_info_spl}
=> run dfuspi
On the host PC:
$ sudo dfu-util -D SPL -a spl
On the target:
CTRL+C
=> setenv dfu_alt_info ${dfu_alt_info_img}
=> run dfuspi
On the host PC:
$ sudo dfu-util -D u-boot.img -a u-boot
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The driver assumed that I2C1 and I2C2 were always enabled,
and if they were not, then an asynchronous abort was (silently)
raised, to be caught much later on in the Linux kernel.
Fix this by making I2C1 and I2C2 optional just like I2C3 and I2C4
are.
To make the change binary-invariant, declare I2C1 and I2C2 in
every include/configs/ file which defines CONFIG_SYS_I2C_MXC.
Also, while updating README about CONFIG_SYS_I2C_MXC_I2C1 and
CONFIG_SYS_I2C_MXC_I2C2, add missing descriptions for I2C4 speed
(CONFIG_SYS_MXC_I2C4_SPEED) and slave (CONFIG_SYS_MXC_I2C4_SLAVE)
config options.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Set missing boot address in bootm command. This fixes the error:
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Reported-by: Uwe Scheffler <scheffler.u@web.de>
Signed-off-by: Soeren Moch <smoch@web.de>
Tested-by: Uwe Scheffler <scheffler.u@web.de>
If defined CONFIG_ENV_IS_IN_MMC, then u-boot environment is saved in
mmc's raw sectors. Otherwise, u-boot environment is saved as a file:
uboot.env.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Bo Shen <voice.shen@gmail.com>
This patch makes use of the previous changes to add a new "fel" boot
target for sunxi boards.
When booting via FEL, it's often desirable to work around the absence
of other (usable) boot devices - or to be able to override them,
deviating from the standard boot sequence. To achieve this, the "fel"
boot target gets the highest priority, but won't actually do anything
unless certain criteria are met.
The "bootcmd_fel" implementation proposed here first tests if an actual
FEL boot takes place (using the "fel_booted" env var), and secondly
checks that "fel_scriptaddr" was set (originating from the 'loader',
i.e. the sunxi-tools fel utility). If both checks pass, then it will
try to execute the boot script (boot.scr) at the given address. In case
of an error (e.g. an invalid image), the source command might return
"false", causing "distro_bootcmd" to proceed with the next boot target.
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
For the upcoming nand support we need a bigger heap, esp. ubi[fs] uses
quite a bit of memory, increase the heap size to 64 MB.
Our video code returns unused reserved framebuffer memory to the kernel
before booting it. Drop the #ifdef-ery and simply always reserve 16 MB.
Adjust bootm_size for the above changes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Move some #define-s around from one #ifdef block to another to
reduce the number of #ifdef blocks (note this causes no functional
changes even though the conditions are not always exactly the same)
and move generic #include statements to the top.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
DRAM region 0x3f000000 - 0x3fffffff is reserved for OP-TEE. Touching
0x3f000000 memory location from unsecure world causes the board
to hang.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use DM for the pl01x serial driver on hikey. Also allow UART0 or
UART3 to be chosen via Kconfig.
By default we now output to UART3 as the latest version of ATF outputs
to this UART. Also UART3 comes out on the LS connector, as opposed to
UART0 which goes to a unpopulated header.
As part of this change we also enable CONFIG_BOARD_EARLY_INIT_F and
call the pinmux configuration code for the UART. Before we were
relying on ATF having already configured the pin configuration.
NB: Upstream Linux kernel doesn't yet support UART3, so serial console
will still be output on UART0 when booting a upstream kernel.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Most platforms enable these options from Kconfig rather
than the configs header file.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use the #defines in linux/sizes for malloc size as it is
more readable.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
When AM437x EVM is connected to Gigabit switch, it takes
more time to finish auto-negotiation than on a 10/100 switch.
The default 4 second limit times-out more often than not. This is
observed when testing with a D-Link DGS-1008A desktop switch.
Increase the auto-negotiation time-out for AM437x EVM to handle
this case.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The config option has been removed by one of the syncs with the Linux
mainline MTD subsystem:
ff94bc40af (mtd, ubi, ubifs: resync with Linux-3.14)
It has been left inside the config files. Currently does not look to
serve any purpose, so remove it now from all the configs.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Cc: Stefan Roese <sr@denx.de>
Cc: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Stefan Roese <sr@denx.de>
Before this commit, the Kconfig menu in mach-uniphier only allowed us
to choose one SoC to be compiled. Each SoC has its own defconfig file
for the build-test coverage. Consequently, some defconfig files are
duplicated with only the difference in CONFIG_DEFAULT_DEVICE_TREE and
CONFIG_{SOC_NAME}=y.
Now, most of board-specific parameters have been moved to device trees,
so it makes sense to include init code of multiple SoCs into a single
image as long as the SoCs have similar architecture. In fact, some
SoCs of UniPhier family are very similar:
- PH1-LD4 and PH1-sLD8
- PH1-LD6b and ProXstream2 (will be added in the upcoming commit)
This commit will be helpful to merge some defconfig files for better
maintainability.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, console=ttyS0 is hard-coded in CONFIG_EXTRA_ENV_SETTINGS
and it replaces the bootargs in the chosen node of the device tree
passed to the kernel. This is not preferable because I am going to
add some boards whose console is not ttyS0.
Drop bootargs settings from U-Boot's environment and use the one in
device tree by default.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
I want these prefixed with CONFIG_ARCH_UNIPHIER_ to clarify
they belong to UniPhier SoC family.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
It is no longer necessary to define CONFIG_SUPPORT_CARD_* globally.
Move them to a C file as local macros. Also, rename the C file.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Device tree specifies the available memory ranges in its "/memory"
node. Use it to simplify the CONFIG defines.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In UniPhier SoCs before ProXstream2 and PH1-LD6b, two address spaces
0x00000000 - 0x0fffffff
0x40000000 - 0x4fffffff
are both mapped to the external bus (also called system bus),
so either was OK.
In the newest two SoCs, the former (0x00000000 - 0x0fffffff) is
assigned for the serial NOR interface.
Going forward, use the latter for the external bus.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Historically (for compatibility with very old platforms), two
different types of micro support cards have been used with the
UniPhier SoC development boards. It has been painful to maintain
both. Having one of them is enough.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We use outer pmic reset and drop internal reset signal, bmode will
not work as expected, so drop boot mode code for 7dsabresd board.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Adrian Alonso <aalonso@freescale.com>
Rename the socfpga_cyclone5.h to socfpga_cyclone5_socdk.h, and
socfpga_arria.h to socfpga_arria5_socdk.h. This matches the other SoCFPGA
board config files.
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
By not defining CONFIG_SYS_ARM_CACHE_WRITEALLOC, the WRITEBACK cache
policy is selected. This leads to much better performance on the SoCFPGA.
A quick network test shows this:
Without this patch:
=> tftp 100000 big-40mb
Speed: 1000, full duplex
Using dwmac.ff702000 device
TFTP from server 192.168.1.54; our IP address is 192.168.1.252
Filename 'big-40mb'.
Load address: 0x100000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
##########################
2.5 MiB/s
With this patch:
=> tftp 100000 big-40mb
Speed: 1000, full duplex
Using dwmac.ff702000 device
TFTP from server 192.168.1.54; our IP address is 192.168.1.252
Filename 'big-40mb'.
Load address: 0x100000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
##########################
7.6 MiB/s
A performance improvement of factor ~3.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
This patch replaces the parser used by VSC9953 L2 Switch driver with
the generic one. Also, the config macro that enables the
VSC9953 commands has been replaced in all the platforms that
use this driver with the config macro that corresponds to the
generic parser.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This adds static register programming for PCIe and USB after memory
init as required by Quark firmware writer guide. Although not doing
this did not cause any malfunction, just do it for safety.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The counter frequency is derived from clk_m on Tegra, but that clock can
be configured by the primary bootloader to run at the same frequency as
the oscillator (38.4 MHz on Tegra210) or a divided down frequency (most
typically 19.2 MHz). Remove the hard-coded frequency and allow the timer
setup code to query the correct value at runtime.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The counter frequency is derived from clk_m on Tegra, but that clock can
be configured by the primary bootloader to run at the same frequency as
the oscillator (38.4 MHz on Tegra210) or a divided down frequency (most
typically 19.2 MHz). Remove the hard-coded frequency and allow the timer
setup code to query the correct value at runtime.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The counter frequency is derived from clk_m on Tegra, but that clock can
be configured by the primary bootloader to run at the same frequency as
the oscillator (38.4 MHz on Tegra210) or a divided down frequency (most
typically 19.2 MHz). Remove the hard-coded frequency and allow the timer
setup code to query the correct value at runtime.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Commit 181bd9dc61 "kconfig: add config option for shell prompt" replaced
define V_PROMPT with Kconfig option SYS_PROMPT. This crossed with patches
adding Tegra T210 boards. Migrate the boards to the new scheme.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
While T210 boards all have 38.4MHz crystals, per the TRM, the only
supported configuration is to divide the crystal frequency by 2 to
generate clk_m, which is what feeds the ARM generic timers amongst other
things. Fix the value of COUNTER_FREQUENCY to reflect this divide-by-2.
When I queried the 19.2 value in Tom's original T210 patches, I wasn't
aware of this extra divide-by-2, and didn't notice any effect from the
incorrect value, since its only used if U-Boot is booted in EL3, whereas
I'm booting it in EL2.
Reported-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
P2371-2180 is a P2180 CPU board married to a P2597 I/O board. The
combination contains SoC, DRAM, eMMC, SD card slot, HDMI, USB
micro-B port, Ethernet via USB3, USB3 host port, SATA, PCIe, and
two GPIO expansion headers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tested on my TI186x rev E. (PG2.0) and take over maintainership.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Take over maintainership as well. Not tested as PG2.0 (which I have)
needs additional work over PG1.0 (which Matt has).
Cc: Matt Porter <mporter@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Tested on my OMAP3 uEVM.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
On the LaCie boards netspace_max_v2 and net2big_v2, two internal hard
drives are available. Additionally on the d2net_v2 board, an extra hard
drive can be plugged via eSATA.
This patch updates CONFIG_SYS_IDE_MAXBUS and CONFIG_SYS_IDE_MAXDEVICE
accordingly for this boards.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
This patch enables generic board support for the following
Kirkwood-based LaCie boards:
- Network Space v2 (Mini, Lite and Max).
- Internet Space v2.
- D2 Network v2.
- 2Big Network v2.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error
message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve
this problem.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
CONFIG_FEC_DMA_MINALIGN is not used anywhere, so let's remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Peng Fan <Peng.Fan@freescale.com>
There is no need to undef the config options.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Peng Fan <Peng.Fan@freescale.com>
CONFIG_ROM_UNIFIED_SECTIONS is not used anywhere, so let's remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Peng Fan <Peng.Fan@freescale.com>
CONFIG_SYS_GENERIC_BOARD is selected by mx6_common.h, so there is no
need to define it locally.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Peng Fan <Peng.Fan@freescale.com>
CONFIG_CMD_FUSE and CONFIG_MXC_OCOTP are selected by mx6_common.h,
so there is no need to define them locally.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
If the SD card does not contain the u-boot.img then we get the
following error:
U-Boot SPL 2015.10-rc2-23947-g7ad5930 (Sep 08 2015 - 14:10:29)
** Partition 1 not valid on device 0 **
spl_register_fat_device: fat register err - -1
spl_load_image_fat: error reading image u-boot.img, err - -1
Remove CONFIG_SPL_FAT_SUPPORT and let CONFIG_SPL_MMC_SUPPORT do the
job.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
If the SD card does not contain the u-boot.img then we get the
following error:
U-Boot SPL 2015.10-rc2-23947-g7ad5930 (Sep 08 2015 - 14:10:29)
** Partition 1 not valid on device 0 **
spl_register_fat_device: fat register err - -1
spl_load_image_fat: error reading image u-boot.img, err - -1
Remove CONFIG_SPL_FAT_SUPPORT and let CONFIG_SPL_MMC_SUPPORT do the
job.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
If the SD card does not contain the u-boot.img then we get the
following error:
U-Boot SPL 2015.10-rc2-23947-g7ad5930 (Sep 08 2015 - 14:10:29)
** Partition 1 not valid on device 0 **
spl_register_fat_device: fat register err - -1
spl_load_image_fat: error reading image u-boot.img, err - -1
Remove CONFIG_SPL_FAT_SUPPORT and let CONFIG_SPL_MMC_SUPPORT do the
job.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch is to support mx6ul_9x9_evk board based on mx6ul_14x14_evk,
the difference between mx6ul 9x9 evk and mx6ul 14x14 evk are:
1. mx6ul 9x9 evk use pfuze3000, while mx6ul 14x14 evk use DCDC.
2. mx6ul 9x9 evk supports 256MB LPDDR2, while mx6ul 14x14 evk
supports 512MB DDR3
3. mx6ul_9x9_evk use 9x9 package, while mx6ul_14x14_evk use 14x14 package.
This patch add the following:
1. Discard PHYS_SDRAM_SIZE from header file, use imx_ddr_size()
2. Introduce a macro is_mx6ul_9x9_evk using
CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) to avoid "#ifdef xxx" in non-SPL
part. To SPL part, CONFIG_IS_ENABLED(TARGET_MX6UL_9X9_EVK) can not work,
so still use "#ifdef CONFIG_TARGET_MX6UL_9X9_EVK" to differentiate with
mx6ul_14x14_evk. And we have no way to dymaically checking this chip
is 9x9 or 14x14.
3. mx6ul_9x9_evk use pfuze3000, so enabled POWER related configurations.
POWER related configurations also effect for mx6ul_14x14_evk. But
power_init_board implementation using 'if (is_mx6ul_9x9_evk())' to
do initialization for mx6ul_9x9_evk, and do nothing for mx6ul_14x14_evk.
4. mx6ul_9x9_evk use lpddr2 with size 256MB, so add related SPL DRAM
configurations.
5. Enable CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and setting dtb file
according to board_rev and board_name.
6. Add TARGET_MX6UL_9X9_EVK Kconfig entry
Boot Log:
U-Boot SPL 2015.10-rc2-00356-g536ce34 (Sep 06 2015 - 12:22:53)
reading u-boot.img
reading u-boot.img
U-Boot 2015.10-rc2-00356-g536ce34 (Sep 06 2015 - 12:22:53 +0800)
CPU: Freescale i.MX6UL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 41C
Reset cause: POR
Board: MX6UL 9x9 EVK
I2C: ready
DRAM: 256 MiB
PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Net: FEC1
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
We have CONFIG_MXC_OCOTP and CONFIG_CMD_FUSE in mx6_common.h,
discard duplicated macro definitions in board header files.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peter Robinson <pbrobinson@gmail.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Rework imx_thermal driver to be used across i.MX
processor that support thermal sensor
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Define CONFIG_MACH_TYPE to allow non DT Linux boot.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Mainline CM-T3517 U-Boot environment size differs from that one
shipped with CM-T3517 boards.
Update environment size, to avoid backward compatibility issues.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
SBC-T3517 evaluation board has two Eth interfaces.
Enable network retry of another interface if the default if failed
or disconnected.
Add 'netretry=yes' in the default env. Setup relevant
timeout values in the board config file.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
This patch changes a little bit the environment, current environment was broken
for a long time, and board don't as expected sometimes, on production systems
this is fixed adding boot script. I think it's time to change this to make a
system conformant environment and use generic distro configurations and
environment instead. We can use a boot script for the old way boot mode.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Add support for Lightwriter SL50 series board, a small, robust and portable
Voice Output Communication Aids (VOCA) designed to meet the particular and
changing needs of people with speech loss resulting from a wide range of
acquired, progressive and congenital conditions.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
This allows transferring data directly to/from RAM. For example, one
could create a boot script that starts DFU on a RAM region, then once
DFU exits (which is under the control of the attached USB host, via a
USB bus reset), uses the code/data that was received over DFU.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Writing to files is a useful feature in general, so enable it everywhere.
The primary purpose is to make DFU useful on filesystems in addition to
raw devices.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
CONFIG_SYS_DFU_DATA_BUF_SIZE defines the size of chunks transferred
across USB. This doesn't need to be particularly large, since it doesn't
limit the overall transfer size.
CONFIG_SYS_DFU_MAX_FILE_SIZE is used to buffer an entire file before
writing it to a filesystem. This define limits the maximum file size that
may be transferred. Bump this up to 32MiB in order to support large
uncompressed kernel images.
Both of these buffers are dynamically allocated, and so the size of both
needs to be taken into account when calculating the required malloc
region size.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Commit 52a7c98a17 "tegra-common: increase malloc pool len by dfu mmc
file buffer size" updated the definition of CONFIG_SYS_MALLOC_LEN for
Tegra to take account of the DFU buffer size. However, this change had
no effect, since typical Tegra board config headers don't set the DFU-
related defines until after tegra-common.h is included. Fix this by
moving the affected conditional code to tegra-common-post.h, which is
included last. Also move the definition of SYS_NONCACHED_MEMORY since
it's a related and adjacent definition.
Fix the condition to test for the DFU feature, rather than specifically
MMC DFU support, so it applies in all cases.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Enable dwc3, dwc3-omap and PHY to get DWC3 functional in OMAP5
uEVM. Also enable support for DFU.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
To reduce the size of the U-Boot image on the x600 board, lets enable
the THUMB mode. This reduces the overall size to less than 0x6000
bytes. Fitting it again in the onboard NOR flash.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
This board is equipped with a Micron NAND chip (MT29F1G08ABADAH4) that
needs 4-bit ECC. But the SPEAr600 only supports 1-bit HW ECC internally.
This patch enables the SW 4-bit BCH support for this board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
This board has not been converted to generic board by the deadline.
Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefano Babic <sbabic@denx.de>
These boards have not been converted to generic board by the deadline.
Remove them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefano Babic <sbabic@denx.de>
These boards have not been converted to generic board by the deadline.
Remove dm355evm, dm355leopard, dm365evm, dm6467evm, dvevm, ea20, schmoogie,
sffsdr, sonata.
Signed-off-by: Simon Glass <sjg@chromium.org>
These boards have not been converted to generic board by the deadline.
Remove all cpu9260 and cpuat91 boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Linux kernel can enumerate mmc sd as either mmcblk0 or mmcblk1.
But u-boot default environment assumes that sd always populates
as mmcblk0. With this the root fs is not being mounted when
mmc sd is enumerated as mmcblk1.
So use partuuid to update root= option in default environment.
Reported-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Define default mmc args in ti_armv7_common.h so that all
TI platforms can reuse.
Reported-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
All TI SoCs expect filesystem to be ext4, omap4_common is the only one
with ext3. move omap4 to ext4 so that we can start consolidating MMC
arguments.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
To simplify and having a common default IP-setup on all B&R boards we
introduce an environment variable "brdefaultip" which does following.
Test if ${ipaddr} is empty, if yes it set's up some defaults:
- ipaddr : 192.168.60.1
- netmask : 255.255.255.0
- gatewayip: 192.168.60.254
- serverip : 192.168.60.254
This environment is ran from CONFIG_PREBOOT.
All other "tricks" are dropped.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
[root@pollux dfu-util]# ./src/dfu-util -l
dfu-util 0.8
Copyright 2005-2009 Weston Schmidt, Harald Welte and OpenMoko Inc.
Copyright 2010-2014 Tormod Volden and Stefan Schmidt
This program is Free Software and has ABSOLUTELY NO WARRANTY
Please report bugs to dfu-util@lists.gnumonks.org
Found DFU: [0908:02d2] ver=0212, devnum=119, cfg=1, intf=0, alt=0, name="Linux", serial="UNKNOWN"
[root@pollux dfu-util]#
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE
into the console and hitting enter afterwards, causes a hang in the
system because CONFIG_SYS_PBSIZE is not capable of storing the extra
characters of the error message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h
to solve this problem.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
Reviewed-by: Simon Glass <sjg@chromium.org>
[fix corrupt line wraps in patch]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
add extensions for the axm board:
- power on LED on power up
- press both recovery buttons on power up to enter
recovery mode
- detect 64 MiB and 128 MiB ramsize
- PHY rest at reboot because of ATMEL bug
- use siemens update concept
- add axm default environment
- set CONFIG_SPL_MAX_SIZE to 15k
Signed-off-by: Heiko Schocher <hs@denx.de>
Now that we have converted the pch_gbe driver to driver moel,
enable it on Intel Crown Bay board.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Since E1000 driver has been converted to driver model, enable it
on Intel Crown Bay. But the Intel Topcliff GbE driver has not been
converted to driver model yet, disable it for now.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add one more ethernet device node in the sandbox test device tree,
with name 'sbe5'. This is to support a new test case for testing
network device rotation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add a PCI node to the device tree. This allows SPI flash and SATA to work
correctly. Also configure the video to come up correctly even though there
is no keyboard.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add support for the Terasic DE0-Nano/Atlas-SoC Kit, which is a CycloneV
based board. The board can boot from SD/MMC. Ethernet is also supported.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Add support for DENX MCV SoM, which is CycloneV based and the
associated DENX MCVEVK baseboard. The board can boot from eMMC.
Ethernet and USB is supported.
Signed-off-by: Marek Vasut <marex@denx.de>
Add support for Terasic SoCkit, which is CycloneV based board.
The board can boot either from SD/MMC or QSPI. Ethernet is also
supported.
Signed-off-by: Marek Vasut <marex@denx.de>
The CONFIG_OF_CONTROL and CONFIG_SPL_OF_CONTROL is always enabled
on Altera SoCFPGA, remove the unnecessary checks.
Signed-off-by: Marek Vasut <marex@denx.de>
Now that MMC works in U-Boot add config distro command support to start
Linux in a standard fashion. One oddity here is that linux fails to load
when the fdt is relocated to above 512MB, so set fdt_high to make sure it's
loaded below that.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The Firefly RK3288 is a suitable target board for initial mainline Rockchip
support. It includes a good set of peripherals, a recent SoC and it is
readily available.
This adds only some basic files required to allow the baord to display a
serial message in SPL and hang.
Signed-off-by: Simon Glass <sjg@chromium.org>
These have not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Dan Malek <dan@embeddedalley.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stefan Roese <sr@denx.de>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stefan Roese <sr@denx.de>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stefan Roese <sr@denx.de>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Remove CONFIG_LWMON5 references.
(Also, remove undefined CONFIG_WD_MAX_RATE while I am here.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stefan Roese <sr@denx.de>
These have not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tolunay Orkun <torkun@nextio.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stefan Roese <sr@denx.de>
there is a 2b board version of the aristainetos2
board. Differences to the v2:
- spi cs for the nor flash and display controller
changed
- some pinmux changes
- LED gpio settings changed
Signed-off-by: Heiko Schocher <hs@denx.de>
make the spi bus and the spi chipselect configurable
for the lg4573 driver. Use it on the aristainetos
boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
Add SPL boot support for mx6slevk board.
1. Introduce a configuration file mx6slevk_spl_defconfig.
2. i.MX6SL has same DRAM space with i.MX6SX, need to change SPL DRAM SPACE.
3. Include imx6_spl.h and related SPL macro in mx6slevk.h.
4. select SUPPORT_SPL for TARGET_MX6SLEVK.
5. Add SPL board code to do related initialization.
Boot Log:
U-Boot SPL 2015.07-00544-g1594a76 (Aug 17 2015 - 01:56:59)
reading u-boot.img
reading u-boot.img
U-Boot 2015.07-00544-g1594a76 (Aug 17 2015 - 01:56:59 +0000)
CPU: Freescale i.MX6SL rev1.2 996 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 50C
Reset cause: POR
Board: MX6SLEVK
I2C: ready
DRAM: 1 GiB
PMIC: PFUZE100 ID=0x10
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
some small updates for the aristainetos boards:
- fix display timings for the aristainetos board
- fix pinmux for the aristainetos board
- fix pinmux for the aristainetos2 board
- fix default environment
Signed-off-by: Heiko Schocher <hs@denx.de>
This commit adds ethernet support to the TS4800. Note that the
MAC address is not fused on this board and have to be read from
FEC PALR PAUR registers (this is how the kernel provided by
Technologic Systems does it).
signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Cc: Stefano Babic <sbabic@denx.de>
This commit adds basic support including:
MMC, Serial console, TS4800 watchdog
The config use CONFIG_SKIP_LOWLEVEL_INIT as U-boot is used as a second
stage bootloader.
Signed-off-by: Lucile Quirion <lucile.quirion@savoirfairelinux.com>
signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Cc: Stefano Babic <sbabic@denx.de>
cgtqmx6eval can be populated with a AR8035 or KSZ9031 depending on the
board revision.
Add Ethernet support.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Discard CONFIG_MX6 in mx6ul_14x14_evk.h, since it is already defined
in mx6_common.h.
Tested on mx6ul_14x14_evk board.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
This patch removes the SPI support from the WRU-IV baseboard as its
not used at all.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Clemens Gruber <clemens.gruber@pqgruber.com>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Currently we need to build one U-boot image for each of the udoo
variants: quad and dual-lite.
By switching to SPL we can support all two variants with a single binary.
Based on the SPL for wandboard.
Tested with OpenELEC (Open Embedded Linux Entertainment Center)
on both boards.
Signed-off-by: Peter Vicman <peter.vicman@gmail.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Peter Vicman <peter.vicman@gmail.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
DEVDISRn registers provides a mechanism for gating clocks of IP blocks
that are not used. Here we implement hwconfig option to allow users
to disable unused peripherals on the board.
For ex. If eSDHC/qDMA/eDMA are unused and with disabled status in dts,
User can enable CONFIG_FSL_DEVICE_DISABLE and set "devdis:esdhc,qdma,edma"
in hwconfig, thus ESDHC controller & eDMA/qDMA will be clock gated to
save more power.
Signed-off-by: Zhuoyu Zhang <Zhuoyu.Zhang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The X-QSGMII-16PORT is a 4xQSGMII/8xSGMII riser card with eighth SerDes
interfaces implemented in PCIe form factor board.
It supports followings
- Card can operate with up to 4 QSGMII lane simultaneously
- Card can operate with up to 8 SGMII lane simultaneously
Add support of X-QSGMII-16PORT riser card.
This patch also take care of back-ward compatiblity with old SGMII rise cards
used on LS2085QDS Platform.
Signed-off-by: King Chung Lo@freescale.com <KingChungLo@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable CONFIG_CMD_GREPENV to allow search in env variables
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LS2085 targets supports following UART console
LS2085AQDS UART0
LS2085ARDB UART1
LS2085ASim UART0
LS2085AEmu UART0
So update the bootargs as per the default console present at the target
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Convert MPC8540ADS, MPC8541CDS, MPC8544CDS, MPC8548CDS, MPC8555CDS,
MPC8560ADS, MPC8568MDS, MPC8569MDS, MPC8610HPCD to use generic board
structure.
Signed-off-by: York Sun <yorksun@freescale.com>
For e6500 and e5500 SoCs, it was intended to put init_ram address in
ccsr reserved space. It is no longer true since SerDes module took the
space. Move it to another reserved space at CCSR + 0x03c000.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The address of the I2C TPM is now defined in the device tree so there is no
need for the CONFIG options.
Remove them from the README and board config to avoid confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Stout is an entry level development board based on R-Car H2 SoC (R8A7790)
This commit supports the following peripherals:
- SCIFA, I2C, Ethernet, QSPI, SDHI0/2, CPLD
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Make CONFIG_SYS_NAND_U_BOOT_OFFS configurable through Kconfig, just like
SYS_NAND_BUSWIDTH_16BIT this is only enabled on some SoCs using depends,
to avoid double defining it for SoCs which have not yet moved to Kconfig
for this.
Having this in Kconfig is useful because this is something which may
differ from one board to the other even when using the same SoC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Scott Wood <scottwood@freescale.com>
We eventually want to add full nand support, since it makes no sense
to build SPL with nand support and u-boot without, or the other way
around, a single option will suffice.
Renaming the Kconfig option now makes things easier when we add full
nand support in the future.
The "obj-$(CONFIG_NAND_SUNXI) += sunxi_nand_spl.o" is moved to an
"ifdef CONFIG_SPL_BUILD" block in the Makefile.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
CONFIG_SPL_NAND_SUPPORT gets used via IS_ENABLED so it must be defined
to 1, rather then just being defined.
While at remove 2 other unused NAND related defines from sunxi-common.h.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Device Tree really improves code maintainability and is now
available for SPL too.
This is the state-of-the-art implementation in U-boot.
The board files (platform data) are no longer needed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The usbboot environment variable has 'usb start' command but
doesn't have the corresponding 'usb stop' command. This breaks
usb peripheral mode if tried after 'run usbboot' fails to load
the images in usb host mode.
Fix it here by adding 'usb stop' command in usbboot env.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Commit 181bd9dc61 introduced Kconfig selection
for SYS_PROMPT. When applying the new picosam9g45 board this change slipped
through, adopt it.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch brings the following changes to the x600 board support:
- Add USB EHCI support
- Add VFAT support for USB key file access
- Increase malloc size (for UBI / UBIFS usage)
- Enable Thumb mode to save some image space
- Remove unreferenced CONFIG_STACKSIZE
- Remove unreferenced CONFIG_SPL_NO_PRINTF
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vipin Kumar <vk.vipin@gmail.com>
The SPL implementation for SPEAr600 is older than the common SPL
infrastructure. This patch now moves the SPEAr600 SPL over to the
common SPL code.
Tested on the only SPEAr board that currently uses SPL in mainline
U-Boot, the x600.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vipin Kumar <vk.vipin@gmail.com>
Currently u-boot stack is defined at the beginning of MSMC RAM.
This is a problem for uart boot mode as ROM downloads directly to
starting of MSMC RAM.
Fixing it by moving stack to the end of u-boot section and shifting
SYS_TEXT_BASE to the start of MSMC RAM.
Updated division of MSMC RAM is shown below:
-----------------------------------------
| | | |
| U-Boot text |U-Boot | SPL text |
| download | Stack | Download + |
| | | SPL_BSS + |
| | | SPL_STACK |
-----------------------------------------
[1] [2] [3] [4]
[1] SYS_TEXT_BASE (Start of MSMC RAM)
[2] SPL_TEXT_BASE - GBL_DATA_SIZE
[3] SPL_TEXT_BASE
[4] END of SPL
[1] + [2] is at least 1M on all platforms, so no chance of overlap.
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Raspberry Pi by default loads the FDT to 0x00000100 so set fdt_addr_r to
match and move scriptaddr to 0x02000000 to avoid clobbering the FDT.
Signed-off-by: Jonathan Liu <net147@gmail.com>
So far we only enabled one legacy serial port on the SMSC LPC47m
superio chipset on Intel Crown Bay board. As the board also has
dual PS/2 ports routed out, enable the keyboard controller which
is i8042 compatible so that we can use PS/2 keyboard and mouse.
In order to make PS/2 keyboard work with the VGA console, remove
CONFIG_VGA_AS_SINGLE_DEVICE. To boot Linux kernel with PIC mode
using PIRQ routing table, adjust the mask in the device tree to
reserve irq12 which is used by PS/2 mouse.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It looks that x86 chipset always contains a host bridge at pci
b.d.f 0.0.0, so enable this for all boards.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This patch enables NAND support on the Marvell Armada XP
DB-MV784MP-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Peter Morrow <peter@senient.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Add optional LCD support. Note that depending on the toolchain used
one might have to drop some other features to stay within the 0x40000
size limit.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Looks like the define CONFIG_SYS_LCD_PXA_NO_L_BIAS is not used anywhere
else throughout the U-Boot sources any more. Drop it.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Conflicts:
configs/socfpga_arria5_defconfig
configs/socfpga_cyclone5_defconfig
configs/socfpga_socrates_defconfig
Merged these by hand and re-ran savedefconfig on them.
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable the DWAPB GPIO driver for SoCFPGA Cyclone V and Arria V.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Move config for the E1000 Ethernet driver to Kconfig and tidy up affected
boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Also move the spi flash configurations to the at91-sama5_common.h.
Current at91 zImage size is about 3.3M, the old mapping is not
suitable. So update the spi flash map as following:
0x0 ~ 0x004000: at91bootstrap(16k)
0x04000 ~ 0x008000: u-boot env(16k)
0x08000 ~ 0x060000: u-boot(352k)
0x60000 ~ 0x06c000: dtb (48k)
0x6c000 ~ 0x400000: kernel (3M+592k)
In AT91Bootstrap, the U-Boot in spi flash also update to 0x8000, refer
to following commit in AT91Bootstrap:
3e91e54 Kconfig: fix spi flash address
So also update SPL's u-boot load address to 0x8000 in spi flash.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Since sama5d3xek boards has different type of dtb blobs, so we need to detect
the cpu type in runtime.
So we add a new variable $dtb_name. if $dtb_name is not defined, we just use
at91-${board_name}.dtb
as the $dtb_name. Otherwise, we will just load the dtb with
$dtb_name.
For sama5d3xek, we will detect cpu type and make up $dtb_name in
runtime.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
As almost all sama5 sd/mmc env configurations are same, so move them to
at91-sama5_common.h.
Also define CONFIG_ENV_VARS_UBOOT_CONFIG to have the varaible: $board_name.
Then we can use 'at91-${board_name}.dtb' as the dtb name.
TODO: since sama5d3xek has different dtb name, we need to some extra
stuff to make it work on sama5d3xek boards.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
The mpddr.c depends on ATMEL_BASE_MPDDRC for the base address to configure the controller.
This cannot be used when there is more than one controller (i.e. AT91SAM9G45, AT91SAM9M10).
Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
[remove 'new blank line at EOF']
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Use embedded DTB to let users use u-boot instead of u-boot-dtb.bin.
And fix SPL to use this target.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Added usb dwc3 driver support for zynqmp
this also supports the DFU and LTHOR to download
the linux images on to RAM and cen be booted from
those linux images.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We have flipped CONFIG_SPL_DISABLE_OF_CONTROL. We have cleansing
devices, $(SPL_) and CONFIG_IS_ENABLED(), so we are ready to clear
away the ugly logic in include/fdtdec.h:
#ifdef CONFIG_OF_CONTROL
# if defined(CONFIG_SPL_BUILD) && !defined(SPL_OF_CONTROL)
# define OF_CONTROL 0
# else
# define OF_CONTROL 1
# endif
#else
# define OF_CONTROL 0
#endif
Now CONFIG_IS_ENABLED(OF_CONTROL) is the substitute. It refers to
CONFIG_OF_CONTROL for U-boot proper and CONFIG_SPL_OF_CONTROL for
SPL.
Also, we no longer have to cancel CONFIG_OF_CONTROL in
include/config_uncmd_spl.h and scripts/Makefile.spl.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
A number of LPC32xx SLC NAND defines is dictated by controller
hardware limits and OOB layout is defined by operating system, the
definitions are common for all users. Since those macro are used
in out of NAND SLC driver code (simple NAND SPL framework), they can
not be placed into the driver, therefore move them from board config
files to arch/config.h
The change also adds OOB layout details specific to small page NAND
devices taken from Linux kernel.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
Enable TI_EDMA3 and SPL_DMA support, so as to reduce boot time. With
DMA enabled there is almost 3x improvement in read performance. This
helps in reducing boot time in qspiboot mode
Also add EDMA3 base address for DRA7XX and AM57XX.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
This patch enabled the MVEBU PCIe support on the db-88f6820-gp A38x
eval board. It also enabled the Intel E1000 driver support and
adds the initialization of PCIe network controllers to the
board code.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Anton Schubert <anton.schubert@gmx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <eibach@gdsys.de>
This patch enabled the MVEBU PCIe support on the db-mv784mp-gp AXP
eval board. It also enabled the Intel E1000 driver support and
adds the initialization of PCIe network controllers to the
board code.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Anton Schubert <anton.schubert@gmx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch moves CONFIG_SYS_TEXT_BASE to 0x00800000 for all Armada
XP / 38x boards in mainline U-Boot. This is done in preparation for
the ECC SDRAM scrubbing that needs to be done in the main U-Boot.
The SPL (previously bin_hdr) has already scrubbed the area:
0x0000.0000 - 0x0100.0000
In this area this main U-Boot needs to get loaded. The main U-Boot
then can scrub the remaining SDRAM area while running from this
location.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds support for multiple hostcontrollers to the ehci-marvell driver
and enables all 3 usb-hcs on the db-mv784mp-gp board.
It depends on the initial Armada XP usb support patch from Stefan.
Signed-off-by: Anton Schubert <anton.schubert@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch enabled the USB/EHCI support for the Marvell
DB-MV784MP-GP Armada XP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Anton Schubert <anton.schubert@gmx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
The default boot command searches for dofastboot varaiable
and does a fastboot if it is set to 1.
But the condition "if test ${dofastboot} -eq 1" always
returns true if dofastboot is not defined and breaking mmc boot.
So make dofastboot as 0 by default and let the runtime
environment set it if fastboot is required.
Reported-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Set up interrupts correctly so that Linux can use all devices. Use
savedefconfig to regenerate the defconfig file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The BayTrail SoC has 4 different PCI devices IDs regarding to IDE
and AHCI. Add these IDs in pci_ids.h and also add the other SATA
ID in the Bayley Bay and MinnowMax board configuration header.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
