Add support of STM32MP13x Rev.Y for the Silicon revision REV_ID = 0x1003.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add a "secure" version of STM32 boards based on SCMI when RCC_TZCR.TZEN=1.
Only boards provided by STMicroelectronics are concerned:
-STM32MP157A-DK1
-STM32MP157C-DK2
-STM32MP157C-ED1
-STM32MP157C-EV1
The resources secured by RCC_TZCR.TZEN=1 are managed by OP-TEE
and the associated SCMI services, reset and clock.
These device trees are only supported with stm32mp15_defconfig,
with OP-TEE, SCMI and without SPL support.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the node for SCMI firmware with the associated reserved memory nodes
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the node for OP-TEE firmware with the associated reserved memory nodes
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
We have a single platform that is both in the OMAP3 family of parts, but
has an EMIF4 memory controller. Currently we hard-code the size of
chip select 0. Make this more clear by putting the value in the
function rather than a CONFIG option.
Signed-off-by: Tom Rini <trini@konsulko.com>
With the last platform for this architecture removed, remove the rest of
the architecture support as well.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
CONFIG_SYS_AUTOMATIC_SDRAM_DETECTION
CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS
Signed-off-by: Tom Rini <trini@konsulko.com>
All of these symbols are not referenced anywhere else in the code, so
remove them.
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_OHCI_SWAP_REG_ACCESS
CONFIG_SYS_USB_OHCI_CPU_INIT
CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS
CONFIG_SYS_USB_OHCI_SLOT_NAME
CONFIG_USB_ATMEL
CONFIG_USB_ATMEL_CLK_SEL_PLLB
CONFIG_USB_ATMEL_CLK_SEL_UPLL
CONFIG_USB_OHCI_LPC32XX
CONFIG_USB_OHCI_NEW
Signed-off-by: Tom Rini <trini@konsulko.com>
Tighten up symbol dependencies in a number of places. Ensure that a SPL
specific option has at least a direct dependency on SPL. In places
where it's clear that we depend on something more specific, use that
dependency instead. This means in a very small number of places we can
drop redundant dependencies.
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The generic arm linker script contains this section:
.bss __rel_dyn_start (OVERLAY) : {
...
}
The (OVERLAY) syntax in the description causes the .bss section to be
included in the NOR area of the image:
$ objdump -t -j .bss spl/u-boot-spl
SYMBOL TABLE:
0000c61c l d .bss 00000000 .bss
0000c640 l O .bss 00000040 __value.0
0000c68c g O .bss 00000000 __bss_end
0000c61c g O .bss 00000000 __bss_start
0000c680 g O .bss 0000000c stdio_devices
This is what the custom linker script tries to avoid, as the NOR area is
read-only.
Remove the OVERLAY syntax to fix the BSS location:
$ objdump -t -j .bss spl/u-boot-spl
SYMBOL TABLE:
83000000 l d .bss 00000000 .bss
83000000 l O .bss 00000040 __value.0
0000c61c g O .bss 00000000 __image_copy_end
8300004c g O .bss 00000000 __bss_end
83000000 g O .bss 00000000 __bss_start
83000040 g O .bss 0000000c stdio_devices
This restores the state of the linker script before the patch that fixed
the linker lists issue.
Fixes: f6810b749f ("aspeed/ast2600: Fix SPL linker script")
Signed-off-by: Joel Stanley <joel@jms.id.au>
The EVB has an EEPROM on bus 3 and a LM75 temp sensor on bus 7. Enable
those busses we can test the I2C driver.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
The same as the upstream Linux device tree, each i2c bus has a property
specifying the reset line.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Set the pinctrl groups for each I2C bus. These are essential to
I2C operating correctly.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Mark the memory node with u-boot,dm-spl so we can use it
from early SPL on both R5 and A53.
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The spl_enable_dcache() function calls dram_init_banksize()
to get the total memory size. Normally the dram_init_banksize()
setups the memory banks, while the total size is reported
by ddr_init(). This worked so far for K3 since we set the
gd->ram_size in dram_init_banksize() as well.
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
implement overrides for spl_spi_boot_bus() and spl_spi_boot_cs()
lookup functions according to bootmode selection, so as to support
both QSPI and OSPI boot using the same build.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
This converts the following to Kconfig:
CONFIG_KIRKWOOD_EGIGA_INIT
CONFIG_KIRKWOOD_PCIE_INIT
CONFIG_KIRKWOOD_RGMII_PAD_1V8
CONFIG_KM_DISABLE_PCIE
Signed-off-by: Tom Rini <trini@konsulko.com>
As things stand currently, there is only one PowerPC platform that
enables the options for CHAIN_OF_TRUST. From the board header files,
remove a number of never-set options. Remove board specific values from
arch/powerpc/include/asm/fsl_secure_boot.h as well. Rework
include/config_fsl_chain_trust.h to not abuse the CONFIG namespace for
constructing CHAIN_BOOT_CMD. Migrate all of the configurable addresses
to Kconfig.
If any platforms are re-introduced with secure boot support, everything
required should still be here, but now in Kconfig, or requires migration
of an option to Kconfig.
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The way that secure boot is implemented today on NXP ARM platforms does
not reuse the elements found in include/config_fsl_chain_trust.h to
construct CONFIG_SECBOOT but instead board header files have their
environment setup as needed and then fsl_setenv_chain_of_trust() will
set secureboot in the environment. Remove a large number of unused
defines here.
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Move setting of SPL_UBOOT_KEY_HASH to a non-NULL value to Kconfig. As
part of this, change fsl_secboot_validate(...) to check that it is
passed a non-empty string, rather than non-NULL.
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Kshitiz Varshney <kshitiz.varshney@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Make all of the CHAIN_OF_TRUST options be under a single menu and add a
comment for the rest, so the resulting config file reads more clearly.
Remove duplicate CHAIN_OF_TRUST options from
board/congatec/common/Kconfig. Remove duplicate NXP_ESBC config
questions and move to arch/Kconfig.nxp.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_KEY_REVOCATION
CONFIG_SYS_FSL_SFP_BE
CONFIG_SYS_FSL_SFP_LE
CONFIG_SYS_FSL_SFP_VER_3_0
CONFIG_SYS_FSL_SFP_VER_3_2
CONFIG_SYS_FSL_SFP_VER_3_4
CONFIG_SYS_FSL_SRK_LE
This partly means making sure to enable SYS_FSL_ERRATUM_A007186 only for
when CHAIN_OF_TRUST is enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FSL_SEC_MON
CONFIG_SYS_FSL_SEC_MON_BE
CONFIG_SYS_FSL_SEC_MON_LE
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that board/freescale/common/Kconfig is safe to be included once,
globally, rename this to arch/Kconfig.nxp to better reflect that it
contains options that are valid on multiple architectures and SoC
families, and not specific to NXP reference platforms either.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The way that we use this file currently means that we have to guard it
in every platform Kconfig. But it is also required in all NXP
platforms, including non-reference platforms. Make all options in it
have appropriate dependencies so that we can include it a single time
under arch/Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_HETROGENOUS_CLUSTERS
CONFIG_SYS_MAPLE
CONFIG_SYS_CPRI
CONFIG_PPC_CLUSTER_START
CONFIG_DSP_CLUSTER_START
CONFIG_SYS_CPRI_CLK
CONFIG_SYS_ULB_CLK
CONFIG_SYS_ETVPE_CLK
Signed-off-by: Tom Rini <trini@konsulko.com>
We rename the S5P specific "CONFIG_PWM" to CONFIG_PWM_S5P and move it to
Kconfig. Given the usage of CONFIG_PWM_NX, we have that select this new
symbol.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
After more patches code for jumping to _start_cont symbol in flash memory
involved to code with useless mathematical operations. Currently it does:
r3 := CONFIG_SYS_MONITOR_BASE + ABS(_start_cont) - CONFIG_SYS_MONITOR_BASE
jump to r3
Which is equivalent of just:
r3 := ABS(_start_cont)
jump to r3
The purpose of that code is just to jump to _start_code symbol,
independently of program counter. So branch must be done to absolute
address. Trying to write:
ba _start_cont
just cause linker error:
LD u-boot
powerpc-linux-gnuspe-ld.bfd: arch/powerpc/cpu/mpc85xx/start.o: in function `switch_as':
(.bootpg+0x4b8): relocation truncated to fit: R_PPC_ADDR24 against symbol `_start_cont' defined in .text section in arch/powerpc/cpu/mpc85xx/start.o
make: *** [Makefile:1801: u-boot] Error 1
Probably by the fact that absolute address cannot be expressed by 24-bits.
So write the code via mtlr+blr pattern as it was before and load general
purpose register with absolute address of the symbol:
lis r3,_start_cont@h
ori r3,r3,_start_cont@l
mtlr r3
blr
Seems that gcc and gnu ld linker support symbol@h and symbol@l syntax like
number@h and number@l without any problem. And disassembling of compiler
u-boot binary proved that lis+ori instructions are called with numbers
which represent halves of absolute address of _start_cont symbol.
Signed-off-by: Pali Rohár <pali@kernel.org>
DT node pic@40000 is defined explicitly in p2020-post.dtsi file and also
transitionally via include file pq3-mpic.dtsi. Remove duplicate definition
from p2020-post.dtsi.
No change in final DTB file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Before relocating to SDRAM, the ECC is initialized by clearing the
whole SDRAM. In order to speed this up, dcache_enable is used (see
sdram_init_ecc_bits).
Since commit 503eea4519 ("arm: cp15: update DACR value to activate
access control"), this no longer works, because running code in OCRAM
with the XN bit set causes a page fault. Override dram_bank_mmu_setup
to disable XN in the OCRAM and setup DRAM dcache before relocation.
Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Using udelay while the clocks aren't fully configured causes the timer
system to save the wrong clock rate. Use sdelay and wait_on_value
instead (the values used in these functions were found experimentally).
Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
Add defconfig and Kconfig files for Google Chameleon V3 board
Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add devicetrees for Google Chameleon V3 board
Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add handoff headers for the Google Chameleonv3 variants: 480-2 and
270-3. Both files were generated using qts-filter-a10.sh.
Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmK9nEUcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyEu0B/4v1EQOMBL+VXns8Ipo
Xeq+RDUX/24XcB5s6sTcNlWzvYuX6Z7DCGJ0loK5JxelrOy+YNkRbTRMom1eW9Kn
9dmKa0bcO7auJEww3Nln1IFyx+FXQFGR1V3g1U4535l8b7urTioIK0MUSrG/GLpe
Rlbh31GAYtrGvl06W1F7mwhg7/0AT8IhUFaY9G7s7gKA5muGQQ7ED4nKVoZPeTAl
lrQ/Ecym1ND7aOhd/vuEBtgoGxDWzwf8piT8qykJluJKzBV1Hic0RXCNBmtrTORz
b1GOOpRUgcnTv9U8j4PRyYGKDnmS2OmV2AwL8+V9UJfJgQrkcRlbgpCysIPmMBzo
YPRt
=D79P
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.10-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2022.10 cycle:
This feature set includes mostly fixes and alignments: DT alignment with
Linux for sama7g5, removal of invalid eeprom compatibles, removal of
extra debug_uart_init calls for all at91 boards, support for pio4 driver
pioE bank, and other minor fixes and enhancements for sam9x60 and
sama5d2_icp boards.
On versal platform, enable apb linear mode for apb read and write
execute operations amd disable it when using dma reads. This is done by
xilinx_pm_request() secure calls when CONFIG_ZYNQMP_FIRMWARE is enabled,
else we use direct raw reads and writes in case of mini U-Boot.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220512100535.16364-5-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
When flash operated at non default mode like DDR, flash need to be reset
to operate in SDR mode to read flash ids by spi-nor framework. Reset the
flash to the default state before using the flash. This reset is handled
by a gpio driver, in case of mini U-Boot as gpio driver is disabled, we
do raw read and write access by the registers.
Versal platform utilizes spi calibration for read delay programming, so
incase by default read delay property is set in DT. We make sure not to
use read delay from DT by overwriting read_delay with -1.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220512100535.16364-4-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Sync the pinebook pro to upstream 5.18, in particular this brings
brings in a fix so the DP is disabled so Linux will actually boot.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
For Rockchip boards with the all rk8xx series PMICs (excluding the
rk808), it is sometimes desirable to not boot whenever the device is
plugged in. An example would be for the Odroid Go Advance.
This provides a configurable option to check the PMIC says it was
powered because of a plug-in event. If the value is 1 and this option
is selected, the device shuts down shortly after printing a message
to console stating the reason why it's shutting down. Powering up the
board with the power button is not affected.
This patch parallels the work done in the following patch series:
https://lore.kernel.org/u-boot/20220121133732.2397273-1-andre.przywara@arm.com/
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This commit adds support for the OP-TEE 'tee.bin' v1 format for Rockchip
platforms.
Since OP-TEE 3.8.0, tee.bin contains meta-data in a proprietary format
in addition to the ELF data. They are essential information for proper
initialization of the TEE core, such as the size of the memory region
covered by the TEE or a compact representation of runtime relocation
data when ASLR is enabled.
With OP-TEE 3.8.0 onwards, 'tee.elf' MUST NOT be used and 'tee.bin'
MUST be used instead. Ignoring this recommendation can lead to crashes
as described in [3].
Link: [1] 5dd1570ac5
Link: [2] https://github.com/OP-TEE/optee_os/blob/3.17.0/scripts/gen_tee_bin.py#L275-L302
Link: [3] https://github.com/OP-TEE/optee_os/issues/4542
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
In order to better compare the Linux rk3288.dtsi version
with the u-boot version move the dma-controller nodes
to the DT root.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to better compare the Linux rk3288.dtsi version
with the u-boot version sort the mipi,hdmi,lvds and dp nodes.
Changed:
Rename mipi_dsi label.
Rename dp nodename.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
With the conversion of rockchip-usb-phy.yaml a long time used fallback
string for rk3066a/rk3188 was added. The linux driver doesn't do much with
the GRF phy address range, however the u-boot driver rockchip_usb2_phy.c
does. The bits in GRF_UOC0_CON2 for rk3066a/rk3188 and rk3288 for example
don't match. Remove the usb-phy fallback string for rk3188
to prevent possible strange side effects.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Change define condition in board_usb_init() function
to allow rk3066/rk3188 to use the USB PHY driver.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Introduce board/siemens/common/Kconfig and have it hold FACTORYSET to
start with. Use select for this on the boards that need it.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
- In a number of cases, use CONFIG_ARCH_EXYNOS[45] rather than
CONFIG_EXYNOS[45]
- In other cases, test for CONFIG_ARCH_EXYNOS or CONFIG_ARCH_S5PC1XX
- Migrate specific SoC CONFIG values to Kconfig
- Use CONFIG_TARGET_x rather than CONFIG_x
- Migrate other CONFIG_EXYNOS_x symbols to Kconfig
- Reference CONFIG_EXYNOS_RELOCATE_CODE_BASE directly as EXYNOS_RELOCATE_CODE_BASE
- Rename CONFIG_S5P_PA_SYSRAM to CONFIG_SMP_PEN_ADDR to match the rest
of U-Boot usage.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Since bb5930d5c9 ("exynos: video: Convert several boards to driver
model for video") there have been no callers of any of the exynos_lcd_*
family of functions. Remove these from the boards, and then remove
unused logo and related code as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
The only use of CONFIG_XTFPGA was to build all of the in-tree device
trees. Switch to using CONFIG_XTENSA instead of a non-Kconfig symbol.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tighten up symbol dependencies in a number of places. Ensure that a TPL
specific option has at least a direct dependency on TPL. In places
where it's clear that we depend on something more specific, use that
dependency instead.
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
We want to keep all of the default values for SPL_LDSCRIPT in the same
place both for overall clarity as well as not polluting unrelated config
files.
Signed-off-by: Tom Rini <trini@konsulko.com>
The commit 99e2fbcb69 ("linker_lists: Rename sections to remove .
prefix") changed the name of the linker list sections. As the Aspeed SPL
linker wasn't in the tree yet, it missed the change.
This updates the SPL linker to match arch/arm/cpu/u-boot-spl.lds which
Aspeed was copied from.
Fixes: 442a69c143 ("configs: ast2600: Move SPL bss section to DRAM space")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Currently CONFIG_SPL_TEXT_BASE and CONFIG_SYS_TEXT_BASE addresses are
manually increased by 0x1000 due to .bootpg section. This section has size
of 0x1000 bytes and is manually put by linker script before .text section
(and therefore before base address) when CONFIG_SYS_MPC85XX_NO_RESETVEC is
set. Due to this fact lot of other config options are manually increased by
0x1000 value to make correct layout. Note that entry point is not on
CONFIG_SPL_TEXT_BASE (image+0x1000) but it is really on address
CONFIG_SPL_TEXT_BASE-0x1000 (means at the start of the image).
Cleanup handling of .bootpg section when CONFIG_SYS_MPC85XX_NO_RESETVEC is
set. Put .bootpg code directly into .text section and move text base
address to the start of .bootpg code. And finally remove +0x1000 value from
lot of config options. With this removal custom PHDRS is not used anymore,
so remove it too.
After this change entry point would be at CONFIG_SPL_TEXT_BASE and not at
address -0x1000 anymore.
Tested on P2020 board with SPL and proper U-Boot.
Signed-off-by: Pali Rohár <pali@kernel.org>
Add CAAM support, which is required when enabling HAB secure boot.
Select CONFIG_SPL_DRIVERS_MISC so that CONFIG_IMX_HAB could
build successfully, if selected.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
In case rtt_nom is set to 0 keep ODT disabled (MMDC MPODTCTRL = 0).
No changes required for DDR MR1 Rtt_Nom impedance register, 0 value is
already handled correctly.
No board is currently affected by this change (rtt_nom != 0 on all i.MX6
ddr3 boards), this will be used by a follow-up change.
Fixes: fe0f7f7842 ("mx6: add mmdc configuration for MX6Q/MX6DL")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Fixup thermal trips in Linux device tree according to SoC thermal
grade.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Tested-by: Adam Ford <aford173@gmail.com>
The memory on this board is microchip 24aa025e48 which is compatible with
at24c02 with a page size of 16.
Fix the compatible accordingly.
Reported-by: Sergiu Moga <sergiu.moga@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Tested-by: Sergiu Moga <sergiu.moga@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
microchip,24aa025e48 does not exist in the bindings of this driver.
It can be replaced with atmel,at24c02 which is a standard compatible
and the memory is compatible with this one, depending on the page size.
microchip 24aa02e48 has a page size of 8, while 24aa025e48 has a page
size of 16 bytes.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Heiko Schocher <hs@denx.de>
Change the compatible of the qspi child node to
`jedec,spi-nor` so that it can be properly found
when probing the bus.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
In arch/arm/lib/sections.c there is below code:
char __image_copy_start[0] __section(".__image_copy_start");
But actually 'objdump -t spl/u-boot-spl' not able to find out
symbol '__image_copy_start' for binman update image-pos/size.
So update link file
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
U-Boot's printf() used before setting up U-Boot's serial driver does not
create any output. Use os_printf() for error messages related to loading
the device-tree.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Before setting up the devices U-Boot's printf() function cannot be used
for console output. Provide function os_printf() to print to stderr.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This patch adds support for the SHA-256 Secure Hash Algorithm for CPUs
that have support for the SHA-256 part of the ARM v8 Crypto Extensions.
It greatly improves sha-256 based operations, about 17x faster on iMX8M
evk board. ~12ms vs ~208ms for a 20MiB kernel sha-256 verification.
asm implementation is a simplified version of the Linux version (from
Ard Biesheuvel).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
This patch adds support for the SHA-1 Secure Hash Algorithm for CPUs
that have support for the SHA-1 part of the ARM v8 Crypto Extensions.
It greatly improves sha-1 based operations, about 10x faster on iMX8M
evk board. ~12ms vs ~165ms for a 20MiB kernel sha-1 verification.
asm implementation is a simplified version of the Linux version (from
Ard Biesheuvel).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
cpu:
- Add driver for microblaze cpu
net:
- Add support for DM_ETH_PHY to AXI emac and emaclite
xilinx:
- Switch platforms to DM_ETH_PHY
- DT chagnes in ZynqMP and Zynq
- Enable support for SquashFS
zynqmp:
- Add support for KR260 boards
- Move BSS from address 0
- Move platform identification from board code to soc driver
- Improve zynqmp_psu_init_minimize
versal:
- Enable loading app at EL1
serial:
- Setup default address and clock rates for DEBUG uarts
pinctrl:
- Add support for tri state and output enable properties
relocate-rela:
- Clean relocate-rela implementation for ARM64
- Add support for Microblaze
microblaze:
- Add support for runtime relocation
- Rework cache handling (wiring, Kconfig) based on cpuinfo
- Remove interrupt support
timer:
- Extract axi timer driver from Microblaze to generic location
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYrlYngAKCRDKSWXLKUoM
ITgbAJ9S9xO2QqxtuodWAYMtJfvZ14c7mgCeKnyFTrrBnJkC0wPsGqE71oNJ49o=
=3gGm
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.10' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.10
cpu:
- Add driver for microblaze cpu
net:
- Add support for DM_ETH_PHY to AXI emac and emaclite
xilinx:
- Switch platforms to DM_ETH_PHY
- DT chagnes in ZynqMP and Zynq
- Enable support for SquashFS
zynqmp:
- Add support for KR260 boards
- Move BSS from address 0
- Move platform identification from board code to soc driver
- Improve zynqmp_psu_init_minimize
versal:
- Enable loading app at EL1
serial:
- Setup default address and clock rates for DEBUG uarts
pinctrl:
- Add support for tri state and output enable properties
relocate-rela:
- Clean relocate-rela implementation for ARM64
- Add support for Microblaze
microblaze:
- Add support for runtime relocation
- Rework cache handling (wiring, Kconfig) based on cpuinfo
- Remove interrupt support
timer:
- Extract axi timer driver from Microblaze to generic location
linux system will die if we offline one of the cpu on R40 based board:
eg: echo 0 > /sys/devices/system/cpu/cpu3/online
The reason is that the R40 version of sunxi_cpu_set_power always passes
0 for the CPU number, so we turn off CPU0, regardless of what CPU the
CPU_OFF request came for.
Fix this by passing the proper CPU number, as there are proper power
clamp registers for every of the four cores.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Copy the devicetree source for the A10 SoC and all existing boards
verbatim from the Linux v5.18-rc1 tag.
The previous version of this change was only partially applied.
Fixes: 4746694cba ("ARM: dts: sun4i: Sync from Linux v5.18-rc1")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Building the sandbox with NO_SDL=1 resulted in an undefined reference to
'sandbox_sdl_remove_display'. Resolve this by adding a stub
implementation to match the stubs of the other similar functions.
Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
"size-cells" of the nand controller node should be 0 as the "reg"
property of the nand device node contains the chip select number and not
address information.
The patch fixes the below compilation warning
arch/arm/dts/zynq-zc770-xm011.dtb: Warning (reg_format):
/axi/memory-controller@e000e000/nand-controller@0,0/nand@0:reg: property
has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/6e90665a2dad7fe8ade10b8f57101f8144963791.1655288559.git.michal.simek@amd.com
As per design, all input/rx pins should have fast slew rate and 12mA
drive strength. Rest all pins should be slow slew rate and 4mA drive
strength. Fix usb nodes as per this and remove setting of slow slew rate
for all the usb gorup pins.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/b245c165f05845c1f3ab41a92c82b7ec1538cee4.1655288171.git.michal.simek@amd.com
Move axi timer driver from Microblaze to generic location.
Origin implementation was irq based with counting down timer.
CONFIG_TIMER drivers are designed differently that timer is free running up
timer with automatic reload without any interrupt.
Information about clock rates are find out in timer_pre_probe() that's why
there is no need to get any additional information from DT in the driver
itself (only register offset).
Signed-off-by: Michal Simek <michal.simek@amd.com>
Tested-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/6c12fc86bbc1f17d05c25018862e7b7b03346b36.1654684731.git.michal.simek@amd.com
Add a basic CPU driver that retrieves information about the microblaze CPU
core. cpu_ops handlers are implemented so that the "cpu" command can work
properly:
U-Boot-mONStR> cpu list
0: cpu@0 MicroBlaze @ 50MHz, Rev: 11.0, FPGA family: zynq7000
U-Boot-mONStR> cpu detail
0: cpu@0 MicroBlaze @ 50MHz, Rev: 11.0, FPGA family: zynq7000
ID = 0, freq = 50 MHz: L1 cache, MMU
Note: cpu_ver_lookup[] and family_string_lookup[] arrays were imported from
linux.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-14-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add helper code for PVR (Processor Version Register) data handling. It
will be used by the UCLASS_CPU driver to populate cpuinfo fields at
runtime.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-13-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Align microblaze with the other architectures and provide an
implementation for flush_dcache_range(). Also, remove the microblaze
exception in drivers/core/device.c.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-11-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Introduce a minimal cpuinfo structure to hold cache related info. The
instruction/data cache size and cache line size are initialized early in
the boot to default Kconfig values. They will be overwritten with data
from PVR/dtb if the microblaze UCLASS_CPU driver is enabled.
The cpuinfo struct was placed in global_data to allow the microblaze
UCLASS_CPU driver to also run before relocation (initialized global data
should be read-only before relocation).
gd_cpuinfo() helper macro was added to avoid volatile
"-Wdiscarded-qualifiers" warnings when using the pointer directly.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-10-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com> (s/bralid/brlid/)
All flush_cache() calls in microblaze code are supposed to flush the
entire instruction and data caches, so introduce flush_cache_all()
helper to handle this.
Also, provide implementations for flush_dcache_all() and
invalidate_icache_all() so that icache and dcache u-boot commands can
work.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-9-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Replace XILINX_DCACHE_BYTE_SIZE macro with two Kconfig symbols for
instruction and data caches sizes, respectively:
CONFIG_XILINX_MICROBLAZE0_ICACHE_SIZE
CONFIG_XILINX_MICROBLAZE0_DCACHE_SIZE
Also, get rid of the hardcoded value in icache_disable().
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-8-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com> (s/bralid/brlid/g)
Factor out icache/dcache components from flush_cache() function. Call the
newly added __flush_icache()/__flush_dcache() functions inside
icache_disable() and dcache_disable(), respectively. There is no need to
flush both caches when disabling a particular cache type.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-7-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Replace CONFIG_ICACHE with a Kconfig option more limited in scope -
XILINX_MICROBLAZE0_USE_WIC. It should be enabled if the processor supports
the "wic" (Write to Instruction Cache) instruction. It will be used to
guard "wic" invocations in microblaze cache code.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-6-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Replace CONFIG_DCACHE with a Kconfig option more limited in scope -
XILINX_MICROBLAZE0_USE_WDC. It should be enabled if the processor supports
the "wdc" (Write to Data Cache) instruction. It will be used to guard
"wdc" invocations in microblaze cache code.
Also, drop all ifdefs around flush_cache() calls and only keep one
CONFIG_IS_ENABLED() guard within flush_cache() itself.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-5-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
XILINX_USE_DCACHE macro was removed in 7556fa09e0 ("microblaze: Simplify
cache handling"), but it was still used in a couple of places.
Replace those occurences with CONFIG_DCACHE.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-4-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Microblaze is using NEEDS_MANUAL_RELOC from the beginnging. This is causing
issues with function pointer arrays which need to be updated manually after
relocation. Building code with -fPIC and linking with -pic will remove this
limitation and there is no longer need to run manual update.
By default still old option is enabled but by disabling NEEDS_MANUAL_RELOC
code will be compiled for full relocation.
The patch does couple of things which are connected to each other.
- Define STATIC_RELA dependency to call relocate-rela to fill sections.
- REMAKE_ELF was already enabled but u-boot file can't be used because
sections are empty. relocate-rela will fill them and output file is
u-boot.elf which should be used.
- Add support for full relocation (u-boot.elf)
- Add support for early relocation when u-boot.bin is loaded to different
address then CONFIG_SYS_TEXT_BASE
- Add rela.dyn and dynsym sections
Disabling NEEDS_MANUAL_RELOC U-Boot size increased by 10% of it's original
size (550kB to 608kB).
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/a845670b34925859b2e321875f7588a29f6655f9.1655299267.git.michal.simek@amd.com
Symbol handling depends on compilation flags. Right now manual relocation
is used that's why symbols can be referenced just by name and there is no
need to find them out. But when position independent code (PIC) is used
symbols need to be described differently. That's why having one macro
change is easier than changing the whole code.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/d704e9a267c8b536452fb999111dbfbc9d652be5.1655299267.git.michal.simek@amd.com
Right now U-Boot runs all the time from the same address where it is loaded
but going to full relocation code starting address doesn't need to be fixed
and can be simply discovered from reading PC register. That's why use r20
to get PC address and subtract offset from the beginning to get starting
address.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/044b727c33dfbe662f68512d0da0775a4805f360.1655299267.git.michal.simek@amd.com
Enable u-boot.elf recreation from u-boot.bin to prepare for removing manul
relocation. Enable option for big endian configuration but it is not used
too much that's why it is completely untested.
By supporting this system there is a need to define LITTLE/BIG endian
Kconfig options to pass -EL/-EB flags.
Full command line for u-boot.elf recreation looks like this:
microblazeel-xilinx-linux-gnu-objcopy -I binary -B microblaze \
-O elf32-microblazeel u-boot.bin u-boot-elf.o
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/7e242a519fcd1c693b9103c5599b515af555ca43.1655299267.git.michal.simek@amd.com
CONFIG_SYS_INIT_SP_OFFSET macro place stack to TEXT_BASE - SYS_MALLOC_F_LEN
but there is no reason to do it now because board_init_f_alloc_reserve()
returns exact location where stack should be. That's why stack location is
calculated at run time and there is no need to hardcode it via macro. This
change will help with placing U-Boot to any address.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/e9aee69646e022fd8a96cbee2d2a07ab81fb6e05.1655299267.git.michal.simek@amd.com
When U-Boot starts stack protection can be already enabled that's why setup
the lowest possible SLR value which is address 0. And the highest possible
stack in front of U-Boot. That's why you should never load U-Boot to the
beginning of DDR. There must be some space reserved. Code is using this
location for early malloc space, early global data and stack.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/86b9748bad12142659804d6381bc6bbf20be44f1.1655299267.git.michal.simek@amd.com
Board is using kv260 design for couple of parts defined by spec like i2c
eeproms, ina260, uart, etc.
Board has 4 gems. One gem connected via PS SGMII(GT), another PS RGMII(MIO)
and 2 via EMIO. First two shares the same MIO lines for PHYs. PL based one
have separate EMIO lines via PL.
Also two USB 3.0 with usb hubs are present. USB phys and USB hubs should
have separate reset line. The first usb0 hub also has USB-SD controller
(usb2244) connected to port 0.
To test compatibility with k26 you can run:
fdtoverlay -o /tmp/output.dtb -i arch/arm/dts/zynqmp-sm-k26-revA.dtb \
arch/arm/dts/zynqmp-sck-kr-g-revA.dtbo
Also add support for kr260-revB board. Based on FRU it is revision B
but schematics can be label as revA03.
Changes in revB are:
- SFP light
- GEM2/3 TX_CLK fixes
- PMOD/RPI connector fixes
- Replace si5332 with oscilators
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/dac2ee1826e73b89c8cc1e430354eb43d291f675.1652870941.git.michal.simek@amd.com
Add a fuzzing engine driver for the sandbox to take inputs from
libfuzzer and expose them to the fuzz tests.
Signed-off-by: Andrew Scull <ascull@google.com>
Add an implementation of LLVMFuzzerTestOneInput() that starts the
sandbox on a secondary thread and exposes a function to synchronize the
generation of fuzzing inputs with their consumption by the sandbox.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move the program's entry point to os.c, in preparation for a separate
fuzzing entry point to be added.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add CONFIG_ASAN to build with the Address Sanitizer. This only works
with the sandbox so the config is likewise dependent. The resulting
executable will have ASAN instrumentation, including the leak detector
that can be disabled with the ASAN_OPTIONS environment variable:
ASAN_OPTIONS=detect_leaks=0 ./u-boot
Since u-boot uses its own dlmalloc, dynamic allocations aren't
automatically instrumented, but stack variables and globals are.
Instrumentation could be added to dlmalloc to poison and unpoison memory
as it is allocated and deallocated, and to introduce redzones between
allocations. Alternatively, the sandbox may be able to play games with
the system allocator and somehow still keep the required memory
abstraction. No effort to address dynamic allocation is made by this
patch.
The config is not yet enabled for any targets by default.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rename the sections used to implement linker lists so they begin with
'__u_boot_list' rather than '.u_boot_list'. The double underscore at the
start is still distinct from the single underscore used by the symbol
names.
Having a '.' in the section names conflicts with clang's ASAN
instrumentation which tries to add redzones between the linker list
elements, causing expected accesses to fail. However, clang doesn't try
to add redzones to user sections, which are names with all alphanumeric
and underscore characters.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rename the sections used for defining sandbox command line options so
that they don't start with a '.'. ELF says that sections starting with a
'.' are reserved for system use, but the sandbox runs as a normal user
process so should be using user sections instead.
Clang's ASAN adds redzones to non-user sections and the extra padding
meant that the list of options was being corrupted. Naming the sections
as user sections avoids this issue as clang handles them as we intended.
Signed-off-by: Andrew Scull <ascull@google.com>
Rename the sections used for placing the EFI runtime so that they don't
start with a '.'. ELF says that sections starting with a '.' are
reserved for system use, but the sandbox runs as a normal user process
so should be using user sections instead.
Clang's ASAN adds redzones to non-user sections and the extra padding
meant that the list of options was being corrupted. Naming the sections
as user sections avoids this issue as clang handles them as we intended.
Signed-off-by: Andrew Scull <ascull@google.com>
This was previously needed, but U-Boot is now capable of parsing
the new "phy-connection-type" property that is already used in
the main devicetree.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This syncs the devicetree files with the latest Linux kernel (5.19-rc2).
This also fixes the currently broken ethernet support:
Before:
Net: Could not get PHY for FEC0: addr 0
After:
Net: eth0: ethernet@30be0000
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Timeouts are not expected to happen and are handled as fatal errors.
Increase all timeouts to 1 second as defensive measure to avoid relying
on the timing behaviour of certain firmware versions or configurations.
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
The NVMe firmware in the macOS 13 beta blocks or crashes with u-boot's
current minimal RTKit implementation. It does not provide buffers for
the firmware's buffer requests. The ANS2 firmware included in macOS 11
and 12 tolerates this. The firmware included in the first macOS 13 beta
requires buffers for the crashlog and ioreport endpoints to function.
In the case of the NVMe the buffers are physical memory. Access to
physical memory is guarded by what Apple calls SART.
Import m1n1's SART driver (exclusively used for the NVMe controller).
Implement buffer management helpers for RTKit. These are generic since
other devices (none in u-boot so far) require different handling.
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
AST2600 supports boot from SPI(mmap), eMMC, and UART.
This patch adds the boot mode detection and return the
corresponding boot device type.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
The commit b583348ca8 ("image: fit: Align hash output buffers") places
the hash output buffer at the .bss section. However, AST2600 by default
executes SPL in the NOR flash XIP way. This results in the hash output
cannot be written to the buffer as it is located at the R/X only region.
We need to move the .bss section out of the SPL body to the DRAM space,
where hash output can be written to. This patch includes:
- Define the .bss section base and size
- A new SPL linker script is added with a separate .bss region specified
- Enable CONFIG_SPL_SEPARATE_BSS kconfig option
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Neal Liu <neal_liu@aspeedtech.com>
The HPE SoC is new to linux. A basic device tree layout with minimum
required for linux to boot including a timer and watchdog support has
been created.
The dts file is empty at this point but will be updated in subsequent
updates as board specific features are enabled.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
The GXP is the HPE BMC SoC that is used in the majority
of current generation HPE servers. Traditionally the asic will
last multiple generations of server before being replaced.
Info about SoC:
HPE GXP is the name of the HPE Soc. This SoC is used to implement many BMC
features at HPE. It supports ARMv7 architecture based on the Cortex A9
core. It is capable of using an AXI bus to whicha memory controller is
attached. It has multiple SPI interfaces to connect boot flash and BIOS
flash. It uses a 10/100/1000 MAC for network connectivity. It has multiple
i2c engines to drive connectivity with a host infrastructure. There
currently are no public specifications but this process is being worked.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Seems that u-boot can't probe i2c bus at 2.6Mhz speed, so lower
the speed to the default value 100Khz.
v2: fix i2c1 frequency in the root omap3-u-boot.dtsi include.
Signed-off-by: Anthoine Bourgeois <anthoine.bourgeois@gmail.com>
- Correct livetree support in stm32mp1 boards
- Activate livetree for stm32mp15 DHSOM boards
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAmKsehgACgkQ4rK92eCq
k3UexAf+JThCd7FlN3OkTVKIdZKeNm2KpQxrqt20whiqp/nSUzxXrjdlCTKZEER2
lLJoVnwr+bkmdlqsa6gAZXSsd0lUv37XnLsLA5or278tFNlKp6gzYrz49FR59mVC
ie7/NlY5FgM5qmKGCob7tjwJ78r2/S3T2EaLiAMWUmw2UB5KZU6h3napHZ+1T0se
vaEAVRzAaZeYzKU3k6RBSv2tXQ6ssvfpp9RcXpRGtrN908AqDhHiOfntuOrnsEe0
9rjY1DSXO9a5WqHRm2KQ3FrA/By2layQ+4WH/HgIPHasisnmo3E/euVWmhtTaiT/
g5bOLwyFQ2/RvdMlMxXlKUcuMfNwRA==
=Hhzj
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220620' of https://source.denx.de/u-boot/custodians/u-boot-stm into next
- Add STM32MP13 SoCs support with associated board STM32M135F-DK
- Correct livetree support in stm32mp1 boards
- Activate livetree for stm32mp15 DHSOM boards
A board might need to get the source of the RCW word, which is also the
boot source in most cases.
These defines are taken from the LS1028A and I expect they are the same
across the SoCs with the same chassis, after all, there was already a
reset source for NOR flash.
Signed-off-by: Michael Walle <michael@walle.cc>
Effective page number mask for MAS2 register is stored in macro MAS2_EPN.
Fixes: 2146cf5682 ("Reworked FSL Book-E TLB macros to be more readable")
Signed-off-by: Pali Rohár <pali@kernel.org>
Header file asm/fsl_law.h already provides correct definition for second
and third PCIe controller (LAW_TRGT_IF_PCIE_2 and LAW_TRGT_IF_PCIE_3). But
is missing definition for the first PCIe controller (LAW_TRGT_IF_PCIE_1).
Note that existing definition for LAW_TRGT_IF_PCIE_2 and LAW_TRGT_IF_PCIE_3
are slightly complicated, but are really correct for P2020 platform.
Signed-off-by: Pali Rohár <pali@kernel.org>
When CONFIG_WDT is enabled then non-DM watchdog code cannot be used due to
conflicting functions like watchdog_reset(). So disable compilation of
mpc85xx watchdog_reset() function when CONFIG_WDT is enabled.
Signed-off-by: Pali Rohár <pali@kernel.org>
These frequency calculations depend on the RCW format, which is not
dependent on any particular board. Switch to using ARCH symbols instead
of TARGET.
This whole function could probably use less ifdefs, but for now just do
a minimal conversion.
Fixes: 24cb6f2295 ("fsl-layerscape: Add fsl_esdhc peripheral clock support")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This adds an SFP binding for the processors it is present on. I have
only tested this for the LS1046A.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
QorIQ platforms now use different clock bindings. Although we don't use
the device tree for clocks on this platform, it is helpful to sync it
because then the bindings will more closely match Linux. Additionally,
it allows for using more clock fractions (such as platform/4).
This corresponds to Linux commit b6f5e7019391 ("ARM: dts: ls1021a:
update the clockgen node").
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Replace reference to the correct name STMicroelectronics
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Depending on backup register value, U-Boot SPL maintains the debug unit
powered-on for debugging purpose; only BUCK1 is required for powering
the debug unit, so revert the setting for all the other power lanes,
except BUCK3 that has to be always on.
To be functional this patch requires a modification in the debugger
,openocd for example, to update the STM32MP15 backup register when it is
required to debug SPL after reset. After deeper analysis this behavior
will be never supported in tools so the associated code, will be never
used and the associated code can be removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support of STM32MP13x the ETZPC part of fdt.c
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Change-Id: If2777fbf66b8525a2a447056780aaa04e6b0a9a0
Introduce STM32MP15 function and defines to prepare the
STM32MP13 introduction.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Change-Id: I909b205e73dcf207e0216aae5905c3c52472020e
Compile the device tree of STM32MP13x boards and add the needed
U-Boot add-on.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The freeze controller is required for FPGA partial reconfig.
This node is disable on default.
Enable this node via u-boot fdt command when needed.
Signed-off-by: Yau Wai Gan <yau.wai.gan@intel.com>
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
The freeze controller is required for FPGA partial reconfig.
This node is disable on default.
Enable this node via u-boot fdt command when needed.
Signed-off-by: Yau Wai Gan <yau.wai.gan@intel.com>
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
Override __udelay() as 'always inlined' function so that PSCI code
run in '__secure' section can call this delay function as well.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
Add support of several MAC address in OTP (3 32bits OTP word for
2 MAC address) for SOCs in STM32MP13x family: STM32MP133 and STM32MP135.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Introduce the code in mach-stm32mp and the configuration file
stm32mp13_defconfig for the new STM32MP family.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add config CONFIG_STM32MP15_PWR to handle the
access to regulators managed by the PWR driver defined in
pwr_regulator.c
This driver is only used in U-Boot by STM32MP15x family.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add sub Kconfig for each SOC in the STM32 CPU family.
It is a preliminary step to introduce a new SOC in the STM32MP family.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add mandatory choice for SOC support in ARCH_STM32MP.
This patch is a preliminary step for new SOC introduction
in STM32MP family.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Move code and defines only needed for CONFIG_STM32MP15x in stm32mp15x.c
when low level init without TFABOOT is supported.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
As the get_otp() helper function in bsec are common for all STM32MP family,
move this function in bsec driver
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The SPL is only supported by STM32MP15x not by all the
SOC with STM32MP arch.
Only TFABOOT is supported in next products.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add initial support of STM32MP13 family based on v5.18-rc2
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add DT for DH DRC Compact unit, which is a universal controller device.
The system has two ethernet ports, one CAN, RS485 and RS232, USB, uSD
card slot, eMMC and SDIO Wi-Fi.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add another mux option for SPI2 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add another mux option for CAN1 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add another mux option for UART5 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add another mux option for UART4 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add another mux option for UART3 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The third parameter of dfu_alt_add(), the string description of alternate,
is build in stm32prog_alt_add() with a unnecessary character ';' at the
end of the string.
This separator was required in the first implementation of
dfu_alt_add() but is no more needed in the current implementation;
this separator is managed only in dfu_config_interfaces() which call
dfu_alt_add() for this parameter without this separator.
And since the commit 53b406369e ("DFU: Check the number of arguments
and argument string strictly"), this added character cause an error when
the stm32prog command is executed because the third parameter of
dfu_alt_add() must be a string with a numerical value; 's' must be NULL
in the result of call in dfu_fill_entity_mmc():
third_arg = simple_strtoul(argv[2], &s, 0);
Fixes: 53b406369e ("DFU: Check the number of arguments and argument string strictly")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Currently get_tcr() takes an "el" parameter, to select the proper
version of the TCR_ELx system register.
This is problematic in case of the Apple M1, since it runs with
HCR_EL2.E2H fixed to 1, so TCR_EL2 is actually using the TCR_EL1 layout,
and we get the wrong version.
For U-Boot's purposes the only sensible choice here is the current
exception level, and indeed most callers treat it like that, so let's
remove that parameter and read the current EL inside the function.
This allows us to check for the E2H bit, and pretend it's EL1 in this
case.
There are two callers which don't care about the EL, and they pass 0,
which looks wrong, but is irrelevant in these two cases, since we don't
use the return value there. So the change cannot affect those two.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
With the move to use DM_CLK the boards uart stops working. The used
properties are not supported by the imx8mq clock driver. Thus
the correct baudrate cannot be selected. Remove this properties here and
the board can start with working uart. Keep it in the main dts because
linux handles these porperties fine.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Without this register unlock it is not possible to configure the
pinmux used for mcu spi0.
Fixes: 92e46092f2 ("arch: arm: mach-k3: am642_init: Probe ESM nodes")
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
This new MMC sample select value is obtained from running
tests on multiple Stratix 10 boards and proven working.
Signed-off-by: Yau Wai Gan <yau.wai.gan@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Mark wdog1/pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The Cubox has an unstable phy address - which can appear at either
address 0 (intended) or 4 (unintended).
SoM revision 1.9 has replaced the ar8035 phy with an adin1300, which
will always appear at address 1.
Change the reg property of the phy node to the magic value 0xffffffff,
which indicates to the generic phy driver that all addresses should be
probed. That allows the same node (which is pinned by phy-handle) to match
either the AR8035 PHY at both possible addresses, as well as the new one
at address 1.
Also add the new adi,phy-output-clock property for enabling the 125MHz
clock used by the fec ethernet controller, as submitted to Linux [1].
Linux solves this problem differently:
For the ar8035 phy it will probe both phy nodes in device-tree in order,
and use the one that succeeds. For the new adin1300 it expects U-Boot to
patch the status field in the DTB before booting
While at it also sync the reset-delay with the upstream Linux dtb.
[1] https://patchwork.kernel.org/project/netdevbpf/patch/20220428082848.12191-4-josua@solid-run.com/
Signed-off-by: Josua Mayer <josua@solid-run.com>
The generated flash.bin does not boot the imx8mn evk LPDDR4 variant
as it misses the spl.bin description in binman.
Add its entry to fix the boot on the imx8mn evk LPDDR4 variant.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Arti Zirk <art@zirk.me>
Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Add new lines for error messages to make them easier to read.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
AM62 StarterKit (SK) board is a low cost, small form factor board
designed for TI’s AM625 SoC. It supports the following interfaces:
* 2 GB DDR4 RAM
* x2 Gigabit Ethernet interfaces capable of working in Switch and MAC mode
* x1 HDMI Port with audio + x1 OLDI/LVDS Display interface for Dual Display
* x1 Headphone Jack
* x1 USB2.0 Hub with two Type A host and x1 USB Type-C DRP Port
* x1 UHS-1 capable µSD card slot
* 2.4/5 GHz WLAN + Bluetooth 4.2 through WL1837
* 512 Mbit OSPI flash
* x4 UART through UART-USB bridge
* XDS110 for onboard JTAG debug using USB
* Temperature sensors, user push buttons and LEDs
* 40-pin User Expansion Connector
* 24-pin header for peripherals in MCU island (I2C, UART, SPI, IO)
* 20-pin header for Programmable Realtime Unit (PRU) IO pins
* 15-pin CSI header
Add basic support for AM62-SK.
To keep the changes to minimum. Only UART And SD are supported at the
moment. This should serve as good example for adding new board support
based on AM62x SoC
Schematics: https://www.ti.com/lit/zip/sprr448
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add basic support for AM62 SK. This has 2GB DDR.
Note that stack for R5 SPL is in OCRAM @ 0x7000ffff so that is away from
BSS and does not step on BSS section
Add only the bare minimum required to support UART and SD.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Introduce autogenerated SoC data support clk and device data for the
AM62. Hook it upto to power-domain and clk frameworks of U-Boot.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The AM62 SoC family is the follow on AM335x built on K3 Multicore SoC
architecture platform, providing ultra-low-power modes, dual display,
multi-sensor edge compute, security and other BOM-saving integration.
The AM62 SoC targets broad market to enable applications such as
Industrial HMI, PLC/CNC/Robot control, Medical Equipment, Building
Automation, Appliances and more.
Some highlights of this SoC are:
* Quad-Cortex-A53s (running up to 1.4GHz) in a single cluster.
Pin-to-pin compatible options for single and quad core are available.
* Cortex-M4F for general-purpose or safety usage.
* Dual display support, providing 24-bit RBG parallel interface and
OLDI/LVDS-4 Lane x2, up to 200MHz pixel clock support for 2K display
resolution.
* Selectable GPUsupport, up to 8GFLOPS, providing better user experience
in 3D graphic display case and Android.
* PRU(Programmable Realtime Unit) support for customized programmable
interfaces/IOs.
* Integrated Giga-bit Ethernet switch supporting up to a total of two
external ports (TSN capable).
* 9xUARTs, 5xSPI, 6xI2C, 2xUSB2, 3xCAN-FD, 3x eMMC and SD, GPMC for
NAND/FPGA connection, OSPI memory controller, 3xMcASP for audio,
1x CSI-RX-4L for Camera, eCAP/eQEP, ePWM, among other peripherals.
* Dedicated Centralized System Controller for Security, Power, and
Resource Management.
* Multiple low power modes support, ex: Deep sleep,Standby, MCU-only,
enabling battery powered system design.
AM625 is the first device of the family. Add DT bindings for the same.
More details can be found in the Technical Reference Manual:
https://www.ti.com/lit/pdf/spruiv7
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Gowtham Tammana <g-tammana@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The node name of the bus in the device tree has changed. Also, the length
argument to be passed should be the length of new value. Therefore, fix the
path to usb device tree node as well as the length argument passed.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
For dfu boot mode, the clocks property needs to be deleted and dr_mode
needs to be set to peripheral. Therefore, add the required fixes for the
same.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
This is the initial support for Broadcom's ARM-based 47622 SOC.
In this change, our first SOC is an armv7 platform called 47622. The
initial support includes a bare-bone implementation and dts with ARM
PL011 uart.
The SOC-specific code resides in arch/arm/mach-bcmbca/<soc> and board
related code is in board/broadcom/bcmba.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Signed-off-by: Anand Gore <anand.gore@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Add wkup_gpio pinmux setting which will be used for performing the
DT fixup for hbmc node according to mux selection state, on J721E
EVM, hypermux sel is tied to ·WKUP_GPIO0_8.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Add DT node for HyperBus Memory Controller and hbmc-mux in the
FSS. hbmc-am654 driver uses syscon_get_regmap() call which fails
with current compatible setting.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
This uses the nvmem API to load a mac address from an RTC.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This uses an i2c eeprom to load a mac address using the nvmem interface.
Enable I2C_EEPROM for sandbox SPL since it is the only sandbox config
which doesn't enable it eeprom.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This prevents some conflicts when running sandbox with -D, since the
"rom" mac address will be random and won't match the environment. We
still need to keep addresses for eth1 and eth6 in the environment,
because dm_test_eth_rotate expects to be able to disable them by
removing their envaddr variables. This can likely be fixed in a future
series by adding a function to cause sandbox eth_opts callback for a
particular mac to fail immediately.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Instead of reading a pseudo-rom mac address from the device tree, just use
whatever we get from write_hwaddr. This has the effect of using the mac
address from the environment (or from the device tree, if it is
specified).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
CONFIG_VAL(DEBUG_UART_BASE) expands to CONFIG_DEBUG_UART_BASE or
CONFIG_SPL_DEBUG_UART_BASE or CONFIG_TPL_DEBUG_UART_BASE and allows boards
to set different values for SPL, TPL and U-Boot Proper.
For ns16550 driver this support is there since commit d293759d55
("serial: ns16550: Add support for SPL_DEBUG_UART_BASE").
Signed-off-by: Pali Rohár <pali@kernel.org>
Update the way KWB_CFG_SEC_BOOT_DEV is determined to use
CONFIG_MVEBU_SPL_BOOT_DEVICE_{SPI,MMC} instead of
CONFIG_SPL_BOOT_DEVICE.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
In some cases, when we don't use CONFIG_SPL_FRAMEWORK nor are we on
PowerPC using their specific SPL/TPL framework, we need to specify the
start.S file to use for these typically very constrained systems. Do
this within the Makefile logic, rather than introducing a string-based
CONFIG option, as this would get slightly complex to do in Kconfig for a
very limited number of users.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
board config header files.
Signed-off-by: Tom Rini <trini@konsulko.com>
In the places where PowerPC references CONFIG_SYS_GBL_DATA_OFFSET it
does so as (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET). And
it defines CONFIG_SYS_GBL_DATA_OFFSET in the same manner that other
architectures define CONFIG_SYS_INIT_SP_OFFSET. Other architectures
define CONFIG_SYS_INIT_SP_ADDR as (CONFIG_SYS_INIT_RAM_ADDR +
CONFIG_SYS_INIT_SP_OFFSET) typically. Rename things within PowerPC for
consistency with other architectures.
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently, since we know that in the combination of
CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET all of the "high"
bits are in CONFIG_SYS_INIT_RAM_ADDR and "low" bits are in
CONFIG_SYS_GBL_DATA_OFFSET we reference this separately in start.S, but
added together everywhere else. For clarity consistency, reference the
combined value here instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
