This board is configured with CONFIG_USB1_VBUS_PIN="PH24", but no
regulator exists in its device tree. Add the regulator, so USB will
continue to work when the PHY driver switches to using the regulator
uclass instead of a GPIO.
Update the device tree here because it does not exist in Linux.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add all the i2c nodes for each family, and add specific i2c
overwrites in the related board-specific dts.
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
This driver is actually used for powerpc and m68k/ColdFire.
On ColdFire SoC's, interrupt flag get not set if IIEN flag (mbcr bit6,
interrupt enabled) is not set appropriately before each transfert.
As a result, the transfert hangs forever waiting for IIEN.
This patch set IIEN before each transfert, while considering this fix
as not harming powerpc arch.
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
- improve tegra DC driver to work with panel ops and implement
native 180 degree panel rotation support
- add T30 support to tegra DC driver
- add DSI driver (based on mainline Linux one with minor
adjustments, only T30 tested)
- add get_display_timing ops to simple panel driver
- extend simple panel driver to use it for MIPI DSI panels
which do not require additional DSI commands for setup
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCZDBwUw4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXL3+AJ9EkQKAWXZtlYdAOVl4/nzJnuTCAQCfY58zkDsw
TnAlwmMGWFl3RF6yGXY=
=uYUp
-----END PGP SIGNATURE-----
Merge tag 'video-20230407' of https://source.denx.de/u-boot/custodians/u-boot-video
- fix building sandbox without SDL
- improve tegra DC driver to work with panel ops and implement
native 180 degree panel rotation support
- add T30 support to tegra DC driver
- add DSI driver (based on mainline Linux one with minor
adjustments, only T30 tested)
- add get_display_timing ops to simple panel driver
- extend simple panel driver to use it for MIPI DSI panels
which do not require additional DSI commands for setup
Adds support for both DSI outputs found on Tegra. Only very
minimal functionality is implemented, so advanced features
like ganged mode won't work. Driver is heavily based on
mainline Tegra DSI and re-uses much of its features.
Only T30 is supported for now but T20 support can be added
if any supported devices will be found.
Driver is wrapped as panel driver since Tegra DC driver supports
only panel drivers calls.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF600T T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # HTC One X T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Internal video devices like DSI and HDMI controllers
require sending commands into DC register field.
To make this available, lets create platform data,
which is restricted to pass DC regmap only to
pre-defined devices.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF T30
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # Paz00
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # ASUS TF101 T20
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # HTC One X T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
On popular request make the display driver from T20 work on T30 as
well. Turned out to be quite straight forward. However a few notes
about some things encountered during porting: Of course the T30 device
tree was completely missing host1x as well as PWM support but it turns
out this can simply be copied from T20. The only trouble compiling the
Tegra video driver for T30 had to do with some hard-coded PWM pin
muxing for T20 which is quite ugly anyway. On T30 this gets handled by
a board specific complete pin muxing table. The older Chromium U-Boot
2011.06 which to my knowledge was the only prior attempt at enabling a
display driver for T30 for whatever reason got some clocking stuff
mixed up. Turns out at least for a single display controller T20 and
T30 can be clocked quite similar. Enjoy.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF T30
Tested-by: Jonas Schwöbel <jonasschwoebel@yahoo.de> # Surface RT T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
This is currently broken. If SDL is not installed, SANDBOX_SDL becomes
false and build errors are generated, e.g.:
test/dm/video.c:424: undefined reference to `sandbox_sdl_set_bpp'
Fix it by making the function return an error in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add board code for R8A779G0 V4H White Hawk board.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Synchronize configuration symbols which are now switched to Kconfig
Mallocate gd->bd->bi_boot_params, i.e. drop the assignment
Sort headers, use clrbits_le32(), use BIT macros where appropriate
Use CONFIG_SYS_CLK_FREQ for counter frequency instead of custom macro]
Add Kconfig entry and PRR ID to support R8A779G0 V4H SoC.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Update commit message]
Add DTs for R8A779G0 V4H White Hawk CPU and BreakOut boards.
Based on Linux next 20230228 DTs up to
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tho Vu <tho.vu.wh@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228, update commit message
Rename DTs to match Linux, which has dash between white-hawk]
Add R8A779G0 V4H DT extras for U-Boot.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Update compatible string to match latest upstream]
Add initial DT support for R8A779G0 (R-Car V4H). Based on Linux next
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228, update commit message]
Add board code for R8A779F0 S4 Spider board.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Synchronize configuration symbols which are now switched to Kconfig
Mallocate gd->bd->bi_boot_params, i.e. drop the assignment
Sort headers, use clrbits_le32(), use BIT macros where appropriate
Use CONFIG_SYS_CLK_FREQ for counter frequency instead of custom macro]
Add Kconfig entry and PRR ID to support R8A779F0 S4 SoC.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Update commit message]
Add DTs for R8A779F0 S4 Spider CPU boards and Breakout boards.
Based on Linux next 20230228 DTs up to
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228, update commit message]
Add R8A779F0 S4 DT extras for U-Boot.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Update compatible string to match latest upstream]
Add initial DT for R8A779F0 S4 SoC. Based on Linux next
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228, update commit message]
This adds R-Car Generation 4 (Gen4) support as Renesas ARM64 SoC.
In this version, reusing R-Car Gen3 lowlevel initialize routine [1]
and R-Car Gen3 memory map tables [2] .
[1] arch/arm/mach-rmobile/lowlevel_init_gen3.S
[2] arch/arm/mach-rmobile/memmap-gen3.c
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: - Enable DTO support by default
- Sort the Kconfig lists
- Select RCAR_64 Kconfig option to pull in all the shared
Kconfig options with Gen3, and use where applicable to
deduplicate entries.
- Fix reference [2] typo in commit message
- Drop config options moved to Kconfig, rename rest to CFG_
accordingly to synchronize with upstream changes. Drop
removed CONFIG_VERY_BIG_RAM.
- Move board size limit to arch/Kconfig
- Move GICR_BASE to headers instead of common config]
The assembly for __gnu_thumb1_case_si was taken from upstream gcc and adapted
as width suffix was removed for the add instruction [1].
Signed-off-by: Francis Laniel <francis.laniel@amarulasolutions.com>
Tested-by: Tony Dinh <mibodhi@gmail.com>
[1] 4f181f9c7e/libgcc/config/arm/lib1funcs.S (L2156)
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Tony Dinh <mibodhi@gmail.com>
On mpc832x, SPI can be either handled by CPU or QE.
In order to work in CPU mode, bit 17 of SPMODE has to
be set to 1, that bit is called OP.
Also, data is located at a different place than the one expected
by the driver today. In 8 bits mode with REV set, data to be
transmitted is located in the most significant byte while
received data is located in second byte. So perform the
necessary shifts.
In order to differentiate with other CPUs, a new compatible is
added for mpc832x: fsl,mpc832x-spi
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
The mpc832x has GPIOs handled by the QUICC Engine.
The registers are different from the one for the
non QE mpc83xx GPIOs.
Implement a GPIO driver for those.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
At startup, some RAM is needed (for instance for stack) before
DRAM is initialised.
One way to offer such RAM, used by mpc83xx, is to lock some entries
in the cache. To do that, MMU needs to be activated.
On mpc83xx having a QUICC Engine an alternative is to user some
part of from the Multi User RAM, like done on mpc8xx for instance.
For that, the MMU is not needed.
Activating the MMU is problematic because exception vectors are not
setup yet so in case of ISI or DSI that CPU will crash and reboot.
At the time being, MMU is activated regardless.
Only activate it when locking cache entries to provide initial RAM.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
There are helpers included in soc.h
Declare them static inline so that soc.h can be
included in several places.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
According to the reference manual, the Reset Configuration
Word Low Register bits 2-3 must be set to 0b10.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Introduce a new compatible "fsl,pq2pro-wdt"
On mpc83xx, the prescaling factor is 0x10000.
Don't write the watchdog configuration register in
start.S as it can be written only once.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
mpc8xx, mpc83xx and mpc86xx have similar watchdog with almost same
memory registers.
Refactor the driver to get the register addresses from the
device tree and use the compatible to know the prescale factor.
Calculate the watchdog setup value from the provided timeout.
Don't declare it anymore as an HW_WATCHDOG, u-boot will start
servicing the watchdog early enough.
On mpc8xx the watchdog configuration register is also used for
configuring the bus monitor. So add it as an option to the watchdog
when it is mpc8xx. When watchdog is not selected, leave the
configuration of the initial SYPCR from Kconfig.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
mpc8xx, mpc83xx and mpc86xx have similar watchdog with almost same
memory registers.
Rename it mpc8xxx which is the generic name used for drivers supporting
several mpc families.
The driver will be made more generic in following patch.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
8xx has CONFIG_8xx_GCLK_FREQ which is similar to
CONFIG_SYS_CLK_FREQ, and doesn't set CONFIG_SYS_CLK_FREQ.
Due to that, get_board_sys_clk() returns 0.
Remove CONFIG_8xx_GCLK_FREQ and use CONFIG_SYS_CLK_FREQ instead.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Tag the serial nodes with bootph-all in order to have these nodes and
the drivers available before relocation.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sync the serial nodes of the LX2160A based boards with their
representation in Linux. We also imported the clockgen and sysclk nodes
which are dependencies.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move the serial nodes under the soc node. No changes are made to the
nodes, just their location is changed.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The u-boot dts for these boards do not have an soc node, unlike its
Linux counterpart. This patch just adds the soc node as seen in Linux,
the next patches will move some nodes under it.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tag the serial nodes with bootph-all in order to have these nodes and
the drivers available before relocation.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sync the serial nodes of the LS1088A based boards with their
representation in Linux. We also imported the clockgen and sysclk nodes
which are dependencies.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move the serial nodes under the soc node. No changes are made to the
nodes, just their location is changed.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The u-boot dts for these boards do not have an soc node, unlike its
Linux counterpart. This patch just adds the soc node as seen in Linux,
the next patches will move some nodes under it.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Beacon Embedded has an i.MX8M Plus development kit which consists
of a SOM + baseboard. The SOM includes Bluetooth, WiFi, QSPI, eMMC,
and one Ethernet PHY. The baseboard includes audio, HDMI, USB-C Dual
Role port, USB Hub with five ports, a PCIe slot, and a second Ethernet
PHY. The device trees are already queued for inclusion in Linux 6.3.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for Data Modul i.MX8M Plus eDM SBC board. This is an
evaluation board for various custom display units. Currently
supported are serial console, ethernet, eMMC, SD, SPI NOR, USB.
Signed-off-by: Marek Vasut <marex@denx.de>
Add WDT reboot bindings on DH i.MX6 DHSOM to permit the platform
to reboot via WDT in U-Boot. These are custom U-Boot bindings,
hence they are placed in -u-boot.dtsi .
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
U-Boot can be booted from NAND without SPL by prepending the DCD header to
the actual U-Boot binary. However this requires prepending 1024 bytes to
u-boot.imx (DCD + u-boot.bin).
There is already a similar target to build spl/u-boot-nand-spl.imx, add the
same option for no-SPL boot.
Tested on i.MX6ULL.
The resulting layout of u-boot-nand.imx is:
- Offset 0x0000 (0 KiB): padding
- Offset 0x0400 (1 KiB): DCD header
- Offset 0x1000 (4 KiB): u-boot.bin
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
J721e SK has been broken since at least March 2022.
The main-navss and mcu-navss nodes were renamed and this caused the
A72 SPL to fail early in the boot even before the serial port was
enabled. Fix this.
A later patch series between v2022.07 and v2022.10 additionally broke
boot on this board by introducing hbmc nodes which are not present on
this board. The right fix is to disable these by default in the SOC
dtsi file, but for now we can also disable them in the u-boot dtsi.
With both these fixed, we can now boot the j721e SK board fully from
mainline u-boot.
Fixes: 58d61fb5a7 ("arm: dts: k3-j721e-sk: Add initial A72 specific dts support")
Fixes: 297daac43a ("arm: dts: k3-j721e-mcu-wakeup: Add HyperBus Controller node")
Reported-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
[gadiyar@ti.com: update commit description]
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Bryan Brattlof <bb@ti.com>
Originally, the mmc aliases node was present in imx6qdl-pico.dtsi.
After the sync with Linux in commit d0399a46e7 ("imx6dl/imx6qdl:
synchronise device trees with linux"), the aliases node is gone as
the upstream version does not have it.
This causes a boot regression in which the eMMC card cannot be found anymore.
Fix it by passing the alias node in the u-boot.dtsi file to
restore the original behaviour where the eMMC (esdhc3) was
mapped to mmc0.
Fixes: d0399a46e7 ("imx6dl/imx6qdl: synchronise device trees with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
The image size was increased but the firmware-update part was not
updated. Correct this so that VBE firmware update can succeed with
sandbox_vpl.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 85c66dc95c ("sandbox: Expand size for VPL image")
---------------------------------
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/15819
i.MX patches queued for next:
- Conversions to DM_SERIAL
- Fixes for Toradex boards
- Gateworks Boards
- i.MX8ULP
- EQoS support / fixes, changes in boards
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCZCaU0Q8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76YCKgCgk4OueoIggmes+Ccj8bu1BcQbrfYAoJAgMeKE
It0hrVAifD62TPb2rmHt
=hFVG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-next-20230331' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx into next
u-boot-imx-next-20230331 for next
---------------------------------
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/15819
i.MX patches queued for next:
- Conversions to DM_SERIAL
- Fixes for Toradex boards
- Gateworks Boards
- i.MX8ULP
- EQoS support / fixes, changes in boards
The FEC interface mode is now configured in common board_interface_eth_init()
and called by FEC MAC driver when appropriate. Drop the board side duplicates
if the same functionality.
Signed-off-by: Marek Vasut <marex@denx.de>
The EQoS interface mode is now configured in common board_interface_eth_init()
and called by EQoS MAC driver when appropriate. Drop the board side duplicates
if the same functionality.
Signed-off-by: Marek Vasut <marex@denx.de>
The assigned-clock no longer have to be dropped, the clock are now
defined in clk-imx8mp.c and used by DWMAC driver to configure the
DWMAC clock. Drop the workarounds from U-Boot specific DT extras.
Signed-off-by: Marek Vasut <marex@denx.de>
In order for i2c_num==4 and 5 to stay invalid for non-imx8mp SOCs, the
i2c_ccgr[] array must be sized by the number of initializers present,
not with a hard-coded 6 which would implicitly initialize the last two
elements with zeroes.
Also, the bounds check is off-by-one.
Fixes: c92c3a4453 "ARM: imx: imx8mp: Enable support for i2c5 and i2c6 on i.MX8MP"
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Implement common board_interface_eth_init() and call it from the FEC
driver to configure IOMUXC GPR[1] register according to the PHY mode
obtained from DT. This supports all three interface modes supported by
the i.MX8M Mini/Nano/Plus FEC and supersedes the current board-side
configuration of the same IOMUX GPR[1] duplicated in the board files.
Signed-off-by: Marek Vasut <marex@denx.de>
Implement common board_interface_eth_init() and call it from the DWMAC
driver to configure IOMUXC GPR[1] register according to the PHY mode
obtained from DT. This supports all three interface modes supported by
the i.MX8M Plus DWMAC and supersedes current board-side configuration
of the same IOMUX GPR[1] duplicated in the board files.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
The DWMAC clock in i.MX8M Plus were so far configured via ad-hoc
architecture code. Replace that with DM clock instead. This way,
the driver claims all its required clock, enables and disables
them, and even gets the CSR clock rate and sets the TX clock rate,
without any need of architecture specific register fiddling. Drop
the architecture specific code while at it too.
The adjustment here is modeled after STM32MP15xx clock handling
in this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Add support for DH electronics i.MX8M Plus DHCOM SoM on PDK3 carrier board.
Currently supported are serial console, EQoS and FEC ethernets, eMMC, SD,
SPI NOR and USB 3.0 host.
Signed-off-by: Marek Vasut <marex@denx.de>
The PHY nodes may be activated via DTO in case another SoM variant
is populated into the development kit. Do not delete the nodes.
Signed-off-by: Marek Vasut <marex@denx.de>
The i.MX8MP DHCOM SoM may come with either external RGMII PHY or
LAN8740Ai RMII PHY on the SoM attached to FEC MAC. Add pin mux
settings for both options, so that DT overlay can override these
settings on SoM variant with the LAN8740Ai PHY.
Signed-off-by: Marek Vasut <marex@denx.de>
The i.MX8MP DHCOM SoM may come with either KSZ9131RNXI RGMII PHY
or LAN8740Ai RMII PHY on the SoM attached to EQoS MAC. Add pin
mux settings for both options, so that DT overlay can override
these settings on SoM variant with the LAN8740Ai PHY.
Signed-off-by: Marek Vasut <marex@denx.de>
The current variant of the SoM has LAN8740Ai PHY connected to EQoS
strapped to MDIO address 0 , adjust the MDIO address to match the
hardware.
Signed-off-by: Marek Vasut <marex@denx.de>
Definitions are according to the MV78460 Hardware Specifications.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Tested-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
A385 BootROM fills into bits [31:28] of register 0x182d0 tracing value,
which represents in which state BootROM currently is. BootROM fills one
of the possible values: 0x2 (CPU initialization), 0x3 (UART detection),
0x6 (UART booting), 0x8 (PCI Express booting), 0x9 (parallel or SPI NOR
booting), 0xA (parallel or SPI NAND booting), 0xB (SATA booting) and 0xE
(SD / eMMC booting).
Meaning of these values matches TRACE_* macros from Marvell soc_spec.h file:
https://github.com/MarvellEmbeddedProcessors/u-boot-marvell/blob/u-boot-2013.01-armada-18.06/tools/marvell/doimage_mv/soc_spec.h
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Tested-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This allows to merge BOOT_FROM_MMC and BOOT_FROM_MMC_ALT constants to one
macro. And also allows to extend other BOOT_FROM_* macros for other
variants.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Tested-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
A385 BootROM treats strapping configuration 0x22 as SPI-NAND. So remove
incorrect definition 0x22 as SATA. SATA on A385 has configuration 0x2A.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Tested-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
A385 BootROM treats strapping configuration 0x3f as invalid. When booting
fails (e.g. because of invalid configuration) then BootROM fallbacks to
UART booting.
Detecting BootROM fallback to UART booting is implemented in U-Boot since
commit 2fd4284051 ("ARM: mach-mvebu: handle fall-back to UART boot").
So there is no need to define BOOT_FROM_UART_ALT constant and special
handling for it anymore, remove it.
This change effectively revers commit f3a88e2ca1 ("arm: mvebu: fix boot
from UART on ClearFog Base").
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Tested-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Show correct information in debug() output and use correct names for variables.
No functional change.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
[upstream of vendor commit 19a96f7c40a8fc1d0a6546ac2418d966e5840a99]
The Clearfog devices have only one SDHC device. This is either eMMC if
it is populated on the SOM or SDHC if not. The Linux device tree assumes
the SDHC case. Detect if the device is an eMMC and fixup the device-tree
so it will be detected by Linux.
Ported from vendor repo at https://github.com/SolidRun/u-boot
Signed-off-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
A388 Clearfog MMC is either SD Card or eMMC with different behaviour for
both. Setting the device to non-removable in the u-boot.dtsi allows both
to correctly detect the device.
Signed-off-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Originally, the mmc aliases node was present in imx6qdl-pico.dtsi.
After the sync with Linux in commit d0399a46e7 ("imx6dl/imx6qdl:
synchronise device trees with linux"), the aliases node is gone as
the upstream version does not have it.
This causes a boot regression in which the eMMC card cannot be found anymore.
Fix it by passing the alias node in the u-boot.dtsi file to
restore the original behaviour where the eMMC (esdhc3) was
mapped to mmc0.
Fixes: d0399a46e7 ("imx6dl/imx6qdl: synchronise device trees with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
The OEM Secure World Closed is not a valid lifecycle on iMX8ULP/iMX9.
So remove it from lifecycle print.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Before moving the lifecycle to OEM closed, confirm the lifecycle is
OEM open, otherwise cancel to move forward the lifecycle.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Remove legacy command definitions, change to use new ELE_xxx command
request.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Use common file ele_ahab.c for i.MX9 and iMX8ULP AHAB support, since
both of them use same sentinel ELE APIs
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add get_events API to retrieve any singular events that has occurred
since the FW has started from sentinel
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
From Sentinel FW v0.0.9-9df0f503, the response message of get info API
is changed to add OEM SRK and some states (IMEM, CSAL, TRNG).
With old structure, we get failure from sentinel due to the buffer
size can't fit with new response message. So update the API structure
to fix the issue.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This patch is used to support DBD owner fuse changed to S400 only.
The XRDC PDAC2 for LPAV pbridge5 and MSC1/2/3 for GPIO and LPAV are not
configured by S400 default setting. So these PDAC and MSC are invalid,
only DBD owner can access the corresponding resources.
We have to configure necessary PDAC and MSC for SPL before DDR
initialization.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
To clean the upower codes by aligning codes format, check err_code
and add detail bits list for the memory magic number
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The swton indicates the logic switch, magic number 0xfff80 is hard
to understand, so use macro.
Some board design may not have MIPI_CSI voltage input connected per
data sheet. In that case, the upower power on API may dead loop mu to wait
response, however there is no response. So remove MIPI_CSI here, let
linux power domain driver to runtime enable the power domain.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
At present, in cgc1_pll3_init we don't set the pll3pfd div values,
just use the default 0. But on A1 part, ROM will set PLL3 pfd1div2
to 1 and pfd2div1 to 3.
This finally causes some clocks' rate decreased, for example USDHC.
So clear the PLL3DIV_PFD dividers to get correct rate.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Some space in SRAM0 will be protected by S400 to allow RX SecPriv mode
access only for boot purpose. Since SW will reuse the SRAM0 as SCMI
buffer and SPL container loading buffer, need to reconfigure MRC3.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Need to add DRAM access permission for S400, as S400 needs to access
it When SPL calls image authentication
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
To fit the DBD_EN fused part, we re-design the TRDC and XRDC assignment.
M33 will be the TRDC owner and needs to configure TRDC. A35 is the
XRDC owner, ATF will configure XRDC.
The handshake between U-boot and M33 image is used to sync TRDC and
XRDC configuration completion. Once the handshake is done, A35 and M33
can access the allowed resources in others domain.
The handshake is needed when M33 is booted or DBD_EN fused, because both
cases will enable the TRDC. If handshake is timeout, the boot will hang.
We use SIM GPR0 to pass the info from SPL to u-boot, because before the
handshake, u-boot can't access SEC SIM and FSB.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
As M33 is responsible for TRDC configuration, the settings for A35
nonsecure world access and DMA0 access are moved to M33 image.
So remove the codes to release TRDC and configure it. Just keep
the configurations for reference.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
iMX8ULP A1 S400 ROM removes the setting for MRC4/5. So we have to set
them in SPL to allow access to DDR from A35 and APD PER masters
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Since A1 ROM has fixed the ROM API eMMC issue, we should only use
the workaround for A0.1 part. Add a SOC revision check.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
In both SPL and u-boot, after probing the S400 MU, get the chip revision,
lifecycle and UID from Sentinel.
Update get_cpu_rev to use the chip revision not hard coded it for A0
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Since latest DTS has added multiple MU nodes, using compatible
string to find the device node is not proper. It finds the first
node with the compatible string matched even the node is disabled.
Signed-off-by: Ye Li <ye.li@nxp.com>
Last use of CONFIG_SYS_GPIO1_PRELIM was removed by
commit fae2ea5951 ("ppc: Remove MPC8349EMDS board and ARCH_MPC8349
support").
Last use of CONFIG_SYS_GPIO2_PRELIM was removed even before by
commit 6843862342 ("ppc: Remove caddy2 / vme8349 boards")
Those two items were removed from whitelist by
commit 8cca60a2cb ("Kconfig: Remove some symbols from the whitelist")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Fixes: fae2ea5951 ("ppc: Remove MPC8349EMDS board and ARCH_MPC8349 support")
Last (incorrect) use of those CONFIG items was removed by
commit 9fd9abedcc ("TQM834x: remove defines causing gcc4.4 warnings")
Those items are invalid and should have been removed at the
same time because lblaw[] has only 4 elements.
And they were removed from the whitelist by
commit 9c5df7a2a9 ("mpc83xx: Migrate LBLAW_* to Kconfig")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Fixes: 9fd9abedcc ("TQM834x: remove defines causing gcc4.4 warnings")
For non TI boards it is not possible to enable the do_board_detect()
call as TI_I2C_BOARD_DETECT is defined in board/ti/common/Kconfig.
I want to use do_board_detect() to dectect boards and properties based
on some SPI communication with a FPGA.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The M.2 slots of the related IOT2050 variant need to be configured
according to the plugged cards. This tries to detect the card using the
M.2 configuration pins of the B-key slot. If that fails, a U-Boot
environment variable can be set to configure manually. This variable is
write-permitted also in secure boot mode as it is not able to undermine
the integrity of the booted system.
The configuration is then applied to mux the serdes and to fix up the
device tree passed to or loaded by the bootloader. The fix-ups are
coming from device tree overlays that are embedded into the firmware
image and there also integrity protected. The OS remains free to load
a device tree to which they do not apply: U-Boot will not fail to boot
in that case.
Based on original patch by Chao Zeng.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Add support for the M.2 board based on the iot2050 advanced board.
The board has two m.2 connectors, one is B-keyed, the other E-keyed.
The B-key slot can connect 5G/SSD devices, and E-key can be used for
WIFI/BT devices.
This variant is covered by PG2 firmware image.
Signed-off-by: chao zeng <chao.zeng@siemens.com>
[Jan: align DT to kernel, polish wording]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Use external blob otpcmd.bin to replace the 0xff filled OTP programming
command block to create a firmware image that provisions the OTP on
first boot. This otpcmd.bin is generated from the customer keys using
steps described in the meta-iot2050 integration layer for the device.
Based on original patch by Baocheng Su.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Add hashes and configuration signature stubs to prepare verified boot
of main U-Boot by SPL.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The latest version of the binary-only firmware parts come in a combined
form of FSBL and sysfw containers. This implies some layout changes to
the generated firmware image but also makes handling of artifacts much
simpler (4 files less). The env locations will not change, just the
space reserved for U-Boot will shrink from 4 to 3 MB - still plenty of
space left in practice.
Adjust configuration and documentation accordingly.
Along this change, add a new reservation for update commands of the
user-controlled OTP part. A specific userspace tool will fill it, and
the FSBL will evaluate it during boot. This reservation will use 64K of
the former sysfw section.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Refactor according to the entry `fit: Entry containing a FIT` of
document tools/binman/README.entries.
As the generator uses the device tree name for the config description,
board_fit_config_name_match requires a small adjustment as well.
Signed-off-by: Su Baocheng <baocheng.su@siemens.com>
[Jan: re-add now required CONFIG_OF_LIST, update config matching]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Due to different signature keys, the PG1 and the PG2 boards can no
longer use the same FSBL (tiboot3). This makes it impossible anyway to
maintaine a single flash.bin for both variants, so we can also split the
build.
A new target is added to indicates the build is for PG1 vs. PG2 boards.
Hence now the variants have separated defconfig files.
The runtime board_is_sr1() check does make no sense anymore, so remove
it and replace with build time check.
Documentation is updated accordingly. New binary artifacts are already
available via meta-iot2050.
Signed-off-by: Su Baocheng <baocheng.su@siemens.com>
[Jan: refactor config option into targets, tweak some wordings]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
After the conversion to DM_SERIAL in commit 01f372d8d6 ("udoo_neo:
Select DM_SERIAL and drop iomux board level init") the SPL log is gone
and the U-Boot proper log becomes incomplete:
Core: 80 devices, 18 uclasses, devicetree: separate
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial@2020000
Out: serial@2020000
Err: serial@2020000
Net: eth0: ethernet@2188000
Hit any key to stop autoboot: 0
Introduce the u-boot.dtsi file that passes the u-boot,dm-pre-reloc
properties to the relevant nodes so that UART can be used early in SPL.
With this change, the complete SPL and U-Boot messages are seen again.
Signed-off-by: Fabio Estevam <festevam@denx.de>
While this change is correct for v2023.04 it is not correct for next
(where this is right now) nor post-v2023.04.
This reverts commit 8653e5d3b7.
Signed-off-by: Tom Rini <trini@konsulko.com>
When we do not enable DISTRO_DEFAULTS (generally, to get distro_bootcmd)
we instea do want to imply BOOTSTD_DEFAULTS so that when using bootstd
the general distro boot functionality will still work.
Signed-off-by: Tom Rini <trini@konsulko.com>
These board have moved to standard boot but the old 'distro_bootcmd'
command is still active. Disable DISTRO_DEFAULTS to fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
With recent CONFIG_TEXT_BASE changes, there are inconsistencies between
several settings.
Adjust CONFIG_SYS_MONITOR_LEN to allow more code space. Move the MRC
cache out of the way too.
Fixes: e23cae3080 ("x86: som-db5800-som-6867: Adjust CONFIG_TEXT_BASE")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With recent CONFIG_TEXT_BASE changes, there are inconsistencies between
several settings.
Adjust CONFIG_SYS_MONITOR_LEN to allow more code space. Move the MRC
cache out of the way too.
Fixes: 5d1c8342ae ("x86: dfi-bt700: Adjust CONFIG_TEXT_BASE")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With recent CONFIG_TEXT_BASE changes, there are inconsistencies between
several settings.
Adjust CONFIG_SYS_MONITOR_LEN to allow more code space. Move the MRC
cache out of the way too.
Fixes: 388f93f963 ("x86: conga-qeval20-qa3-e3845: Adjust CONFIG_TEXT_BASE")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
With recent CONFIG_TEXT_BASE changes, there are inconsistencies between
several settings.
Adjust CONFIG_SYS_MONITOR_LEN to allow more code space. Move the MRC
cache out of the way too.
Fixes: f38be30868 ("x86: bayleybay: Adjust CONFIG_TEXT_BASE")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With recent CONFIG_TEXT_BASE changes, there are inconsistencies between
several settings.
Adjust CONFIG_SYS_MONITOR_LEN to allow more code space. Move the MRC
cache out of the way too.
Add documentation on how to make this change safely.
Fixes: 66e2c665f3 ("x86: minnowmax: Adjust CONFIG_TEXT_BASE")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Documenation:
* add man-page for efi command
UEFI:
* Let EFI app call ExitBootServices() before legacy booting kernel
* Support zboot and bootm in the EFI app
* Let efi command show configuration tables
* Support booting a 64-bit kernel from 64-bit EFI app
* Allocate device-tree copy from high memory
* simplify efi_str_to_u16()
-----BEGIN PGP SIGNATURE-----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=a5J7
-----END PGP SIGNATURE-----
Merge tag 'efi-next-20230325' of https://source.denx.de/u-boot/custodians/u-boot-efi into next
Pull request for efi-next-20230325
Documenation:
* add man-page for efi command
UEFI:
* Let EFI app call ExitBootServices() before legacy booting kernel
* Support zboot and bootm in the EFI app
* Let efi command show configuration tables
* Support booting a 64-bit kernel from 64-bit EFI app
* Allocate device-tree copy from high memory
* simplify efi_str_to_u16()
When running the EFI app, we need to exit boot services before jumping
to Linux.
At some point it may be possible to jump to Linux and pass on the system
table, and:
* install the device-tree as configuration table
* use LoadImage() to load the kernel image (e.g. from memory)
* start the image with StartImage()
This should allow the Linux efistub to be used. For now, this is not
implemented.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add the missing code to handle this. For a 64-bit kernel the entry
address is 0x200 bytes after the normal entry.
Rename the parameter to boot_linux_kernel() accordingly. Update the
comments to indicate that these are addresses, not pointers.
Signed-off-by: Simon Glass <sjg@chromium.org>
The U-Boot EFI app can run as a 64-bit program, so set the Kconfig
correctly in that case. Make sure it doesn't build SPL, since there is
no need to switch from 32 to 64 bit when running.
Signed-off-by: Simon Glass <sjg@chromium.org>
- Fixes for booting newer revs of the SoC in the Raspberry Pi 4
- Propagate some firmware DT properties to the loaded DT
- Update the Zero2W upstream DT name
Newer firmware can manage the SDCDIV clock divisor register, allowing
the divisor to scale with the core as necessary.
Leverage this ability if the firmware supports it.
Adapted from the following raspberrypi Linux kernel commit:
bcm2835-sdhost: Firmware manages the clock divisor
08532d242d
Signed-off-by: Vincent Fazio <vfazio@xes-inc.com>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
In rpi-firmware 25e2b597ebfb2495eab4816a276758dcc6ea21f1,
the GET_CLOCK_RATE mailbox property was changed to return the last
value set by SET_CLOCK_RATE.
https://github.com/raspberrypi/firmware/issues/1619#issuecomment-917025502
Due to this change in firmware behavior, bcm2835_get_mmc_clock now
returns a clock rate of zero since we do not issue SET_CLOCK_RATE.
This results in degraded MMC performance.
SET_CLOCK_RATE fixes the clock to a specific value and disables scaling
so is not an ideal solution.
Instead, fallback to GET_MAX_CLOCK_RATE in bcm2835_get_mmc_clock if
GET_CLOCK_RATE returns zero.
Signed-off-by: Vincent Fazio <vfazio@xes-inc.com>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Same change as was done for mvebu in commit 5bb2c550b1 ("arm: mvebu: Move
internal registers in arch_very_early_init() function") but for kirkwood.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
CONFIG_SF_DEFAULT_SPEED is used in SPL SPI to configure and probe the
flash device during DM SPI uclass probing process, if the
spi-max-frequency is not available in the DTB. Currently the max
frequency is not available, because of the probing mechanism in SPI
uclass has not been fully updated to DM.
The CONFIG_SF_DEFAULT_SPEED is set to 1Mhz if a board defconfig
does not specify it. This speed is too slow and result in a few
seconds delay while the u-boot image is loaded from flash. Based on a
survey of the device tree specifications for MVEBU boards, a sane default
value should be 10Mhz. The default of 10Mhz enables an almost
instantaneously loading of the u-boot image.
Note that this patch depends on this patch series (has been merged to
u-boot-marvell/next):
https://lists.denx.de/pipermail/u-boot/2023-March/511038.html
- RESEND: correct spelling of SF_DEFAULT_MODE
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
We did not add a prototype for spl_mmc_get_uboot_raw_sector to
include/spl.h before, so add and document one now. Correct the incorrect
prototype in board/advantech/imx8mp_rsb3720a1/imx8mp_rsb3720a1.c and
ensure that we have spl.h where we define a non-weak
spl_mmc_get_uboot_raw_sector as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Some platforms were not including <cpu_func.h> which sets the prototype
for reset_cpu, and in turn had it set wrong. Correct these cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
On high security devices, ROM enables firewalls to protect the OCSRAM
region access during bootup. Only after TIFS has started (and had
time to disable the OCSRAM firewall region) will we have write access to
the region.
So, move scratch board area to HSM RAM.
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
To make sure the panic and the reset messages will go out, console flush() should be used.
Sleep periods do not work in early u-boot phase when timer driver is not initialized yet.
Reference: https://lists.denx.de/pipermail/u-boot/2023-March/512233.html
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The Rockchip timer driver has been renamed after the fall back compatible.
There's no need to replace the timer compatible in rk3188-radxarock-u-boot.dtsi
anymore, so remove.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable SPL on RK3588 to detect which device it was booted from.
Fixes use of same-as-spl in u-boot,spl-boot-order prop.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Running U-Boot from eMMC on a ROCK 3 Model A result in the following:
U-Boot SPL 2023.04-rc3 (Mar 11 2023 - 17:24:48 +0000)
Trying to boot from MMC1
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
The sdhci node is missing in board device tree, sync device tree from
linux v6.3-rc1 to fix booting from eMMC. Also disable sdmmc2 and uart1
nodes related to using a WiFi and BT module in the M2 slot.
Fixes: b44c54f600 ("arm64: dts: rockchip: rk3568: Add Radxa ROCK 3 Model A board support")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The boot source node path for emmc is using the old sdhci name.
Replace with correct mmc name and also add same-as-spl to boot order.
Fixes: 0d61f8e5f1 ("rockchip: rk3568: add boot device detection")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Running U-Boot on a ROCK 3 Model A result in the following:
No serial driver found
resetting ...
no sysreset
### ERROR ### Please RESET the board ###
Replace bootph- props with u-boot,dm- props to fix this.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There are multiple shared Kconfig options between R-Car Gen3 and Gen4.
Keep the common options in Kconfig.64 and move the R-Car Gen3 specific
options into separate Kconfig.rcar3 . The Kconfig.rcar3 contains SoC
and board list, which is limited to R-Car Gen3.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Introduce common Kconfig symbol for 64bit R-Car platforms and move
common configuration options into it. This is preparatory patch to
prevent duplication of Kconfig lists later on, when Gen4 is added.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Pull the SYS_SOC Kconfig option to avoid duplication of this option
in Kconfig.{32,64,rza1} . The default value is the same, so just set
it in one location.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Switch ifdef in rmobile_get_prr() to IS_ENABLED() macro.
The CONFIG_RCAR_GEN3 will never have SPL counterpart, so
the IS_ENABLED() macro is the right one here. No functional
change, except for improved build test coverage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
All R-Car Gen3 defconfigs present in U-Boot do enable DTO support,
enable it for all of R-Car Gen3 by default in Kconfig instead, so
that no new boards would miss this functionality.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Per Andre:
[T]hese two patches containing just devicetree updates for
Allwinner boards.
I was still hoping for a review, since we cannot import the files from
the Linux tree verbatim, but managed to write some filter script that
convinced me that the changes are fine.
The files are from Linux v6.2-rc2, but are identical to the v6.2
release.
Fix error:
Invalid chip select 0:1 (err=-19)
update spi nor "compatible" property with "jedec,spi-nor"
to have spi nor properly bound as a child device.
Signed-off-by: Angelo Durgehello <angelo@kernel-space.org>
This patch fixes u-boot hanging on the first printf("%x", val).
Some toolchains built without multilib enabled may produce
u-boot freezing on first u64 shift operation, as in
lib/vsprintf.c number() function.
Using our private libgcc solves the issue.
Setting private libgcc enabled at architecture level to avoid
similar issues, it should not harm.
Signed-off-by: Angelo Durgehello <angelo@kernel-space.org>
The FSL eSDHC controller supports two reference clocks. They are
platform clock and periperhal clock. The global variable sdhc_clk
has already been used for platform clock.
ColdFire also uses eSHDC controller, as in arm and powerpc,
so adding sdhc_per_clk to arch_global_data.
Signed-off-by: Angelo Durgehello <angelo@kernel-space.org>
Tag the serial nodes with bootph-all in order to have these nodes and
the drivers available before relocation.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sync the serial nodes of the LS208XA RDB/QDS boards with their
representation in Linux. We also imported the clockgen and sysclk nodes
which are dependencies.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move the serial nodes under the soc node. No changes are made to the
nodes, just their location is changed.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The u-boot dts for these boards do not have an soc node, unlike its
Linux counterpart. This patch just adds the soc node as seen in Linux,
the next patches will move some nodes under it.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When the first device tree description was added for the ethernet nodes,
the 2 10G ports on the LS1088ARDB were wrongly described as 'xgmii'.
Fix this by replacing the two last occurrences of 'xgmii' in the device
trees of the Layerscape DPAA2 devices.
Fixes: 68c7c008e8 ("arm: dts: ls1088ardb: add DPMAC and PHY nodes")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The Odroid Go Ultra has 2 chained PMICs RK818 and RK818, and needs
an adjustment on the BUCK and LDO values.
Add the initial regulators values in -u-boot.dtsi & run the initial
regulator setup in a new odroid-go-ultra board.
Proper OTG and BOOST regulators are still missing to have USB-A
host properly working.
Link: https://lore.kernel.org/r/20230210-u-boot-odroid-go-ultra-pmics-setup-v1-1-1f16d62b76af@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add support for this to EFI in case it becomes useful. At present it just
slows things down. You can enable CONFIG_VIDEO_COPY to turn it on.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current vesa structure only provides a 32-bit value for the frame
buffer. Many modern machines use an address outside the range.
It is still useful to have this common struct, but add a separate
frame-buffer address as well.
Add a comment for vesa_setup_video_priv() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Runtime relocation has been made the default for microblaze, so do the
following cleanups:
- drop all manual reloc codepaths in start.S
- drop all STATIC_RELA ifdefs, as it is now enabled unconditionally in
Kconfig
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20230311173838.521804-5-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Microblaze and m68k are the only remaining architectures that still enable
CONFIG_NEEDS_MANUAL_RELOC by default.
Microblaze has had runtime relocation support using CONFIG_STATIC_RELA for
quite some time, since commit d58c007498 ("microblaze: Add support for run
time relocation"). Drop support for CONFIG_NEEDS_MANUAL_RELOC and make
runtime relocation the default, as the rest of the architectures do.
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20230311173838.521804-4-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Enable support for sysinfo on R-Car D3 Draak board. The sysinfo is used
e.g. to access and decode board-specific information and then in turn
used by board-info to print those information.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Drop compatible from I2C node, this is in r8a77995.dtsi already.
Drop status = "okay" from EEPROM node.
Add dts: tag.
Fix Kconfig EEPROM address to be 0x50 and match the DT, sync config.]
Add new sysinfo IDs for R-Car V3H Condor/Condor-I .
Enable support for sysinfo on R-Car V3H Condor/Condor-I. The sysinfo is
used e.g. to access and decode board-specific information and then in
turn used by board-info to print those information.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Drop compatible from I2C node, this is in r8a77980.dtsi already.
Drop status = "okay" from EEPROM node.
Add dts: tag.
Update the commit message, note the new sysinfo IDs.
Fix Kconfig EEPROM address to be 0x50 and match the DT, sync config.]
By default enable nand-on-flash-bbt DT flag, so that driver always refers
to the bad block table(bbt) present on the flash device.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230224050709.30014-5-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
DC3 nand node is not correct, it is showing all partitions under
controller node directly. Create two sub nand nodes with partitions for
each.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230224050709.30014-4-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The latest SOM specification doesn't enforce certain MIO lines allocated
for ethernet or ethernet controller itself. That's why remove comment about
it which is likely there from early version of specification.
Also removed the same comment from pinctrl node. It is clear that it has to
be defined for different carrier cards.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/9406377bf2c391ac0200670511bd6b0edb097c96.1676880543.git.michal.simek@amd.com
Since the zynqmp boards can run upstream OP-TEE, and having the DT node
present doesn't cause any side effects add it in case someone tries to
load OP-TEE.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Link: https://lore.kernel.org/r/20230216133921.866786-1-ilias.apalodimas@linaro.org
Signed-off-by: Michal Simek <michal.simek@amd.com>
The pl330 DMA controller provides number of DMA channels and requests
through its registers, so duplicating this information (with a chance of
mistakes) in DTS is pointless. Additionally the DTS used always wrong
property names which causes DT schema check failures - the bindings
documented 'dma-channels' and 'dma-requests' properties without leading
hash sign.
Reported-by: Rob Herring <robh@kernel.org>
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20220430121902.59895-2-krzysztof.kozlowski@linaro.org
Since we need to support legacy phys with the dwc3 controller,
we enable this quirk on the zynqmp platforms.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20221023215649.221726-1-m.grzeschik@pengutronix.de
Signed-off-by: Michal Simek <michal.simek@amd.com>
The node names should be generic and DT schema expects certain pattern:
xilinx/zynqmp-zcu100-revC.dtb: leds: 'vbus-det' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221125144136.477171-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Michal Simek <michal.simek@amd.com>
cdns prefix was deprecated and replaced by xlnx one in upstream Linux. Also
U-Boot driver has been updated to support new compatible string that's why
it is time to remove it and deprecate it.
Signed-off-by: Michal Simek <michal.simek@amd.com>
So far we used inline assembly to inject the actual instruction that
triggers the semihosting service. While this sounds elegant, as it's
really only about a few instructions, it has some serious downsides:
- We need some barriers in place to force the compiler to issue writes
to a data structure before issuing the trap instruction.
- We need to convince the compiler to actually fill the structures that
we use pointers to.
- We need a memory clobber to avoid the compiler caching the data in
those structures, when semihosting writes data back.
- We need register arguments to make sure the function ID and the
pointer land in the right registers.
This is all doable, but fragile and somewhat cumbersome. Since we now
have a separate function in an extra file anyway, we can do away with
all the magic and just write that in an actual assembler.
This is much more readable and robust.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
So far we used inline assembly to inject the actual instruction that
triggers the semihosting service. While this sounds elegant, as it's
really only about one instruction, it has some serious downsides:
- We need some barriers in place to force the compiler to issue writes
to a data structure before issuing the trap instruction.
- We need to convince the compiler to actually fill the structures that
we use pointers to.
- We need a memory clobber to avoid the compiler caching the data in
those structures, when semihosting writes data back.
- We need register arguments to make sure the function ID and the
pointer land in the right registers.
This is all doable, but fragile and somewhat cumbersome. Since we now
have a separate function in an extra file anyway, we can do away with
all the magic and just write that in an actual assembly file.
This is much more readable and robust.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
AM62A7-SK board has 4GB LPDDR4 Micron MT53E2G32D4DE-046 AUT:B part
but only 2GB was enabled early.
Enable full 4GB memory by updating the latter 2GB memory region
which gets mapped to 0x0880000000 i.e. DDR16SS0_SDRAM as referred in
Table 2-1. AM62A Common SoC Memory of AM62Ax TRM [1].
[1] : https://www.ti.com/lit/zip/spruj16
Logs: https://gist.github.com/devarsht/e85b6af89c01ddadb3a62f3e5f196af8
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Synchronize devicetree sources with Linux v6.2.
- Use GIC interrupt definitions
- Add reg properties in USB-glue and SoC-glue node
- Fix node names to follow the generic names list in DT specification
- Add L2 cache and AHCI nodes
- Update nand and pcie nodes
- And some trivial fixes
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Marek Vasut <marex@denx.de>
UniPhier DT applies its own USB node for U-Boot due to the USB driver
constrains. After solving this issue, u-boot allows the original USB node.
After switching USB node, synchronization of USB node with Linux becomes
possible.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Marek Vasut <marex@denx.de>
Commit fe7d654d04 ("mpc83xx: Migrate CONFIG_SYS_{BR, OR}*_PRELIM to
Kconfig") converted CONFIG_SYS_{BRx/ORx}_PRELIM to Kconfig by
implementing a fine-grained selection of every bit in Kconfig.
But commit c7fad78ec0 ("Convert CONFIG_SYS_BR0_PRELIM et al to
Kconfig") reworked it so that you now just have to provide the raw
value of each register in Kconfig. However, all fine-grained
Kconfig items remained allthough they are not used anymore.
Remove them all.
Fixes: c7fad78ec0 ("Convert CONFIG_SYS_BR0_PRELIM et al to Kconfig")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
As the lastest spear directories are removed, delete the associated entry
in Makefile.
Fixes: 570c3dcfc1 ("arm: Remove spear600 boards and the rest of SPEAr support")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
count_required_pts()'s complexity is high if mappings are not using the
largest possible block size (due to some other requirement such as tracking
dirty pages, for example).
Let's switch to a method that follows the pattern established with
the add_map() helper, and make it almost instantaneous instead of
taking a large amount of time if 2MB mappings are in use instead of
1GB.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Pierre-Clément Tosi <ptosi@google.com>
[ Paul: pick from the Android tree. Fixup Pierre's commit. Rebase to the
upstream ]
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Tom Rini <trini@konsulko.com>
Link: 5d756d147e
Link: 6be9330601
In the add_map() function, for each level it populates, it iterates from
the root of the PT tree, making it ineficient if a mapping needs to occur
past level 1.
Instead, replace it with a recursive (and much simpler) algorithm
that keeps the complexity as low as possible. With this, mapping
512GB at level 2 goes from several seconds down to not measurable
on an A55 machine.
We keep the block mappings at level 1 for now though.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Pierre-Clément Tosi <ptosi@google.com>
[ Paul: pick from the Android tree. Fixup Pierre's commit. Rebase to the
upstream ]
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Tom Rini <trini@konsulko.com>
Link: 96ad729cf4
Link: 6be9330601
Memory used to hold the page tables is allocated from the top of RAM
with no prior initialization and could therefore hold invalid data. As
invalidate_dcache_all() will be called before the MMU has been
initialized and as that function relies indirectly on the page tables
when using CMO_BY_VA_ONLY, these must be in a valid state from their
allocation.
Signed-off-by: Pierre-Clément Tosi <ptosi@google.com>
[ Paul: pick from the Android tree. Fix checkpatch warnings, and rebased
to the upstream. ]
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Tom Rini <trini@konsulko.com>
Link: e3ceef4230
Exposing set/way cache maintenance to a virtual machine is unsafe, not
least because the instructions are not permission-checked but also
because they are not broadcast between CPUs. Consequently, KVM traps and
emulates such maintenance in the host kernel using by-VA operations and
looping over the stage-2 page-tables. However, when running under
protected KVM, these instructions are not able to be emulated and will
instead result in an exception being delivered to the guest.
Introduce CONFIG_CMO_BY_VA_ONLY so that virtual platforms can select
this option and perform by-VA cache maintenance instead of using the
set/way instructions.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Will Deacon <willdeacon@google.com>
Signed-off-by: Pierre-Clément Tosi <ptosi@google.com>
[ Paul: pick from the Android tree. Fixup Pierre's commit. And fix some
checkpatch warnings. Rebased to upstream. ]
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Tom Rini <trini@konsulko.com>
Link: db5507f47f
Link: 2baf54e743
Sync the devicetree files from the Linux kernel repo, v6.2-rc2.
This is covering the 64-bit SoCs, from arch/arm64/boot/dts/allwinner.
This enables GPU power management in the kernel for the H6, enables
Bluetooth on the Pinebook, and adds USB to the H616 devices (just
for newer Linux kernels at the moment, U-Boot support is pending).
As before, this omits the non-backwards compatible changes to the R_INTC
controller, to remain compatible with older kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Sync the devicetree files from the Linux kernel repo, v6.2-rc2.
This is covering the 32-bit SoCs, from arch/arm/boot/dts.
This enables some new devices for the F1C100s family, though this is of
little relevance to U-Boot itself.
The H3 gains the "phys" property for the first USB controller, which
prevents an error message when U-Boot's USB stack comes up, and allows
using this port in host mode.
As before, this omits the non-backwards compatible changes to the R_INTC
controller, to remain compatible with older kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This is used by ls1021atwr_sdcard_ifc_SECURE_BOOT with split config, but
is not needed anymore, since Ethernet migration is complete. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we enable the sandbox RTC driver for all builds. Add a separate
Kconfig option to control this, so that it can be disabled in TPL, where
it is not needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
We don't need to provide an empty arch_misc_init function here, we can
just not enable the hook.
Cc: Stefan Bosch <stefan_b@posteo.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
If this hooks is needed later, it should be added and populated for
real.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
In this platform, arch_misc_init doesn't perform any real function. The
call to get_soc_type_rev has no lasting side effects.
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
We don't need an empty function, we can just not enable the hook we
don't use.
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
On the lion and evb-px5 platforms, we need this function, so select it.
Cc: Andy Yan <andy.yan@rock-chips.com>
Cc: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Cc: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
The function arch_early_init_r only does anything on these platforms if
we have FPGA (or SPL and SPL_FPGA) enabled, so move the logic to select
based on that.
Cc: Michal Simek <michal.simek@amd.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We need to be calling arch_early_init_r() on 64bit mvebu platforms, so
move this to a select.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmP+97wcHGV1Z2VuLmhy
aXN0ZXZAY29sbGFib3JhLmNvbQAKCRAesx4CDqwvyExpB/wLQVjeBM+sEcABzT52
c7qtAvtgl/UbPedYyMz2YorL5BcHsdmBbGfSzBISEc8kLdtAVMTKAaqvN7msaJFX
MwPIZAXWd8cPM0EA7wSyjYDGOvcEzGWF7oxSbeq+j7M2kibvsQLGW7iaY5cjFIzx
QPQ19T2tyX3jrsy8dxCsPivB70vB/3lqiEmCZX2UddsjxrL6Vt2H3k6O+/Ler5wS
/nJIzKLDPc+aDZSv+aevDlJZi1eGkpTHldNaHXqdYILzvnXIQmA6kP0mWPZ9g6wZ
s6ed1N5VeiS4j6oH5Woj3nDKny7P3AKSd9+c/eXfbtdia2D0yBHtiHQauIwNPCd3
wAcH
=/Vn2
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-fixes-2023.04-a' of https://source.denx.de/u-boot/custodians/u-boot-at91
First set of u-boot-at91 fixes for the 2023.04 cycle:
This fixes set include one clock index fix for sama7g5 and two board
configuration alignments for pm9g45.
In SPL are active memory maps set by the BootROM. Define them in cpu.h file
to the correct values. Some peripherals are not mapped at all.
Signed-off-by: Pali Rohár <pali@kernel.org>
Proper U-Boot moves SPI0 CS0 Flash mapping from 0xD4000000 to 0xF4000000
and change its size from 64 MB to 8 MB. Definitions are already in
MBUS_SPI_BASE/MBUS_SPI_SIZE macros. So define these macros also for SPL
build, use them in env_sf_get_env_addr() function and move this function
from spl.c to cpu.c to be available in Proper U-Boot too.
Signed-off-by: Pali Rohár <pali@kernel.org>
MVEBU_SPL_BOOT_DEVICE_SPI is for NOR flash. Either serial or parallel. Not
for general serial/SPI devices. The correct name should be BOOT_DEVICE_NOR
but name SPI is already used in mkimage config format which we do not want
to change for compatibility reasons.
MVEBU_SPL_BOOT_DEVICE_MMC is for MMC and SD compatible devices. Not for
SDIO devices. In most cases used for eMMC or SD card.
Signed-off-by: Pali Rohár <pali@kernel.org>
Add a new Kconfig option CONFIG_MVEBU_SPL_BOOT_DEVICE_PEX which instruct
make to generate kwbimage with PEX header. This image is used for booting
from PCI Express device which is in the Root Complex mode.
Support is very simple, SPL after finishes DDR training returns back to the
BootROM (via CONFIG_SPL_BOOTROM_SUPPORT option) and BootROM then start
executing U-Boot proper.
Signed-off-by: Pali Rohár <pali@kernel.org>
Add a new Kconfig option CONFIG_MVEBU_SPL_BOOT_DEVICE_NAND which instruct
make to generate kwbimage with NAND header. This image is used for booting
from NAND flash (either SPI or parallel).
Support is very simple, SPL after finishes DDR training returns back to the
BootROM (via CONFIG_SPL_BOOTROM_SUPPORT option) and BootROM then loads and
executes U-Boot proper.
To generate correct kwbimage NAND header, it is required to set following
Kconfig options:
CONFIG_SYS_NAND_PAGE_SIZE
CONFIG_SYS_NAND_BLOCK_SIZE
CONFIG_MVEBU_SPL_NAND_BADBLK_LOCATION
They are used only by make / mkimage when generating final kwbimage.
CONFIG_MVEBU_SPL_NAND_BADBLK_LOCATION is a new mvebu specific Kconfig
option which is set into kwbimage NAND_BADBLK_LOCATION header field.
Signed-off-by: Pali Rohár <pali@kernel.org>
Marvell BootROM loads MMC image from sector 0 (HW boot or data partition)
and SD image from sector 1.
So for SD card booting it is needed to not use constant CONFIG MMC options
and instead of them it is needed to define functions spl_mmc_boot_mode()
spl_mmc_get_uboot_raw_sector() which determinate offsets at SPL runtime
based on MMC or SD card.
Calculation of SD card sector expects following values:
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_DATA_PART_OFFSET=0
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0
Fixes: 2226ca1734 ("arm: mvebu: Load U-Boot proper binary in SPL code based on kwbimage header")
Signed-off-by: Pali Rohár <pali@kernel.org>
When eMMC boot is selected then BootROM loads kwbimage header (U-Boot SPL)
from the selected eMMC boot partition. So for eMMC boot ensure that U-Boot
SPL loads U-Boot proper (from kwbimage) also from the same selected eMMC
boot partition.
Fixes: 2226ca1734 ("arm: mvebu: Load U-Boot proper binary in SPL code based on kwbimage header")
Signed-off-by: Pali Rohár <pali@kernel.org>
BOOT_DEVICE_MMC2 and BOOT_DEVICE_MMC2_2 are representing mmc dev 1 but all
Armada SoCs have only one mmc controller. So remove references to
non-existent second mmc controller.
Fixes: f830703f42 ("arm: mvebu: Check that kwbimage blockid matches boot mode")
Signed-off-by: Pali Rohár <pali@kernel.org>
Despite the official specification, Marvell BootROM does not interpret
srcaddr from SATA image as number of sectors the beginning of the hard
drive, but as number of sectors relative to the main header.
To process SATA kwbimage and load U-Boot proper from it in the same way as
Marvell BootROM, it is needed to interpret srcaddr as relative offset to
the main header. This change fixes booting of U-Boot proper from SPL code
in SATA image.
Fixes: 2226ca1734 ("arm: mvebu: Load U-Boot proper binary in SPL code based on kwbimage header")
Signed-off-by: Pali Rohár <pali@kernel.org>
Despite the official specification, Marvell BootROM does not interpret
srcaddr from SDIO image as offset in number of sectors (like for SATA
image), but as offset in bytes (like for all other images except SATA).
To process SDIO kwbimage and load U-Boot proper from it in the same way as
Marvell BootROM, it is needed to interpret srcaddr in bytes. This change
fixes booting of U-Boot proper from SPL code stored in SDIO image.
Fixes: 2226ca1734 ("arm: mvebu: Load U-Boot proper binary in SPL code based on kwbimage header")
Signed-off-by: Pali Rohár <pali@kernel.org>
ROCK 5B is a Rockchip RK3588 based SBC (Single Board Computer) by Radxa.
There are tree variants depending on the DRAM size : 4G, 8G and 16G.
Specification:
Rockchip Rk3588 SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
4/8/16GB memory LPDDR4x
Mali G610MC4 GPU
MIPI CSI 2 multiple lanes connector
eMMC module connector
uSD slot (up to 128GB)
2x USB 2.0, 2x USB 3.0
2x HDMI output, 1x HDMI input
Ethernet port
40-pin IO header including UART, SPI, I2C and 5V DC power in
USB PD over USB Type-C
Size: 85mm x 54mm
Kernel commits:
a1d3281450ab ("arm64: dts: rockchip: Add rock-5b board")
6fb13f888f2a ("arm64: dts: rockchip: Update sdhci alias for rock-5b")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The cpuid on RK3568 is located at 0xa instead of 0x7 as all other SoCs.
Add and use a CFG_CPUID_OFFSET to define this offset.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Set eth1addr in addition to ethaddr.
Also allow fdt fixup of ethernet mac addresses when CMD_NET is disabled.
Set ethaddr and eth1addr based on HASH and SHA256 options.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 6(Neu2) is a 96boards SoM-CB compute module
based on Rockchip RK3588 from Edgeble AI.
General features:
- Rockchip RK3588
- up to 32GB LPDDR4x
- up to 128GB eMMC
- 2x MIPI CSI2 FPC
On module WiFi6/BT5 is available in the following Neu6 variants.
Neural Compute Module 6(Neu6) IO board is an industrial form factor
ready-to-use IO board from Edgeble AI.
IO board offers plenty of peripherals and connectivity options and
this patch enables basic eMMC and UART which is enough to successfully
boot Linux.
Neu6 needs to mount on top of this IO board in order to create a
complete Edgeble Neural Compute Module 6(Neu6) IO platform.
Boot log for the record,
DDR Version V1.08 20220617
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
Manufacturer ID:0x6
CH0 RX Vref:31.7%, TX Vref:21.8%,21.8%
CH1 RX Vref:30.7%, TX Vref:22.8%,23.8%
CH2 RX Vref:30.7%, TX Vref:22.8%,22.8%
CH3 RX Vref:30.7%, TX Vref:21.8%,21.8%
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
U-Boot SPL 2023.01-00952-g1d1785a516-dirty (Jan 30 2023 - 19:53:55 +0530)
Trying to boot from MMC1
INFO: Preloader serial: 2
NOTICE: BL31: v2.3():v2.3-391-g856309329:derrick.huang
NOTICE: BL31: Built : 14:15:50, Jul 18 2022
INFO: ext 32k is not valid
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: system boots from cpu-hwid-0
INFO: idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001
INFO: dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO: dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO: dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO: dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO: BL31: Initialising Exception Handling Framework
INFO: BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR: Error initializing runtime service opteed_fast
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0xa00000
INFO: SPSR = 0x3c9
U-Boot 2023.01-00952-g1d1785a516-dirty (Jan 30 2023 - 19:53:55 +0530)
Model: Edgeble Neu6A IO Board
DRAM: 7.5 GiB (effective 3.7 GiB)
Core: 71 devices, 15 uclasses, devicetree: separate
MMC: mmc@fe2c0000: 0
Loading Environment from nowhere... OK
In: serial@feb50000
Out: serial@feb50000
Err: serial@feb50000
Model: Edgeble Neu6A IO Board
Net: No ethernet found.
Hit any key to stop autoboot: 0
=>
Add support for Edgeble Neu6 Model A IO Board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Booting from SDMMC is one of the fast and easy booting methods
for initial support of any SoC to upstream more features.
This patch is trying to add the sdmmc node for rk3588 and added
as u-boot specific node in -u-boot.dtsi as upstream Linux is not
supporting yet.
As soon as Linux supports it, a sync of the Linux device tree
would eventually drop this node.
Clock properties as added according to the rockchip mmc driver
but the actual definition might add scmi clocks into 0 and 1
indexes. This is due to scmi clock are not supporting in upstream
U-Boot. Properly addition of scmi clock would eventually follow
sdmmc clock definition of Linux once they upstreamed.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Add u-boot,dm-spl and u-boot,dm-pre-reloc related properties
for Rockchip RK3588 SoC to boot the SPL.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Rockchip RK3588 is a ARM-based SoC with quad-core Cortex-A76
and quad-core Cortex-A55 including NEON and GPU, 6TOPS NPU,
Mali-G610 MP4, HDMI Out, HDMI In, DP, eDP, MIPI DSI, MIPI CSI2,
LPDDR4/4X/5, eMMC5.1, SD3.0/MMC4.5, USB OTG 3.0, Type-C, USB 2.0,
PCIe 3.0, SATA 3, Ethernet, SDIO3.0 I2C, UART, SPI, GPIO and PWM.
Add arch core support for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 6(Neu6) IO board is an industrial form factor
ready-to-use IO board from Edgeble AI.
IO board offers plenty of peripherals and connectivity options and
this patch enables basic eMMC and UART which is enough to successfully
boot Linux.
Neu6 needs to mount on top of this IO board in order to create a
complete Edgeble Neural Compute Module 6(Neu6) IO platform.
commit <a5079a534554> ("arm64: dts: rockchip: rk3588: Add Edgeble Neu6
Model A IO")
Add support for Edgeble Neu6 Model A IO Board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 6(Neu2) is a 96boards SoM-CB compute module
based on Rockchip RK3588 from Edgeble AI.
General features:
- Rockchip RK3588
- up to 32GB LPDDR4x
- up to 128GB eMMC
- 2x MIPI CSI2 FPC
On module WiFi6/BT5 is available in the following Neu6 variants.
Neu6 needs to mount on top of associated Edgeble IO boards for
creating complete platform solutions.
Enable eMMC for now to boot Linux successfully.
commit <3d9a2f7e7c5e> ("arm64: dts: rockchip: rk3588: Add Edgeble Neu6
Model A SoM")
Add support for Edgeble Neu6 Model A SoM.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This initial version supports CPU, dma, interrupts, timers, UART and
SDHCI (everything necessary to boot Linux on this system on chip) as
well as Ethernet, I2C, PWM and SPI.
The DT is split into rk3588 and rk3588s, which is a reduced version
(i.e. with less peripherals) of the former.
commit <9fb232e9911f> (" arm64: dts: rockchip: Add base DT for rk3588
SoC")
commit <d68a97d501f8> ("arm64: dts: rockchip: Add rk3588 pinctrl data")
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add IOC unit header include for rk3588.
Signed-off-by: Steven Liu <steven.liu@rock-chips.com>
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add RK3588 pll set and get rate clock support.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add clock and reset unit header include for rk3588.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add gpio-ranges property to GPIO nodes so that the bank ID can
be correctly derived for each GPIO bank.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
It enables automatic clock gating on idle, disables the eDP phy by
default, and sets the core pvtpll ring length. It is reported this
lowers the temperature on at least one SoC by 7C.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable spl to detect which device it was booted from.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3566 and rk3568 from the mainline Linux kernel (6.2-rc2 as of
this writing).
Note that this will rename the rk3568-evb to rk3568-evb1-v10.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the gpio-ranges property to each GPIO node for use in deriving
the correct bank ID. Note that invoking "gpio status -a" no longer
causes the board to hit a "Synchronous Abort".
Fixes: 537b1a2774 ("rockchip: add px30 devicetrees")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
combphy1 is failing to probe due to unhandled assigned-clocks and
assigned-clocks-rates.
=> usb start
starting USB...
Bus usb@fd000000: Failed to get PHY1 for usb@fd000000
Port not available.
Bus usb@fd800000: USB EHCI 1.00
There is no real requirement for them in U-Boot to handle, hence
mark them as deleted-properties for the probe to success
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Radxa Compute Module 3(CM3) IO board an application board from Radxa
and is compatible with Raspberry Pi CM4 IO form factor.
Radxa CM3 needs to mount on top of this IO board in order to create
complete Radxa CM3 IO board platform.
Add support for Radxa CM3 IO Board defconfig and -u-boot.dtsi
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Radxa Compute Module 3(CM3) IO board an application board from Radxa
and is compatible with Raspberry Pi CM4 IO form factor.
Specification:
- 1x HDMI,
- 2x MIPI DSI
- 2x MIPI CSI2
- 1x eDP
- 1x PCIe card
- 2x SATA
- 2x USB 2.0 Host
- 1x USB 3.0
- 1x USB 2.0 OTG
- Phone jack
- microSD slot
- 40-pin GPIO expansion header
- 12V DC
Radxa CM3 needs to mount on top of this IO board in order to create
complete Radxa CM3 IO board platform.
linux-next commit for the same,
commit <8f19828844f2> ("arm64: dts: rockchip: Fix compatible for Radxa
CM3")
Add support for Radxa CM3 IO Board.
Co-developed-by: FUKAUMI Naoki <naoki@radxa.com>
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Co-developed-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Radxa Compute Module 3(CM3) is one of the modules from a series
System On Module based on the Radxa ROCK 3 series and is compatible
with Raspberry Pi CM4 pinout and form factor.
Specification:
- Rockchip RK3566
- up to 8GB LPDDR4
- up to 128GB high performance eMMC
- Optional wireless LAN, 2.4GHz and 5.0GHz IEEE 802.11b/g/n/ac wireless,
BT 5.0, BLE with onboard and external antenna.
- Gigabit Ethernet PHY
Radxa CM3 needs to mount on top of this IO board in order to create
complete Radxa CM3 IO board platform.
Since Radxa CM3 is compatible with Raspberry Pi CM4 pinout so it is
possible to mount Radxa CM3 on top of the Rasberry Pi CM4 IO board.
linux-next commit for the same,
commit <8f19828844f2> ("arm64: dts: rockchip: Fix compatible for Radxa
CM3")
Add support for Radxa CM3.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Co-developed-by: FUKAUMI Naoki <naoki@radxa.com>
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Like other rockchip SoCs, DM_RESET is useful across rk3568
platform.
Select it from arch kconfig.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add Radxa ROCK 3 Model A support. sync rk3308-rock-pi-s.dts from
Linux 6.2.0-rc7.
ROCK Pi S is RK3308 based SBC from radxa.com. ROCK Pi S has a,
- 256MB/512MB DDR3 RAM
- SD, NAND flash (optional on board 1/2/4/8Gb)
- 100MB ethernet, PoE (optional)
- Onboard 802.11 b/g/n wifi + Bluetooth 4.0 Module
- USB2.0 Type-A HOST x1
- USB3.0 Type-C OTG x1
- 26-pin expansion header
- USB Type-C DC 5V Power Supply
Linux commit commit for the same,
<2e04c25b1320> ("arm64: dts: rockchip: add ROCK Pi S DTS support")
Signed-off-by: Akash Gajjar <gajjar04akash@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add Radxa ROCK 3 Model A support. sync rk3568-rock-3a.dts from Linux 6.2.0-rc7
Board Specifications
- Rockchip RK3568
- 2/4/8GB LPDDR4 3200MT/s
- eMMC socket, SD card slot
- GbE LAN
- PCIe 3.0/2.0
- M.2 Connector
- 3.5mm Audio jack with mic
- HDMI 2.0, MIPI DSI/CSI
- USB 3.0 Host/OTG, USB 2.0 Host
- 40-pin GPIO expansion ports
- USB Type C PD 2.0, 9V/2A, 12V/2A, 15V/2A, 20V/2A
Refer Linux commit <22a442e6586c>
("arm64: dts: rockchip: add basic dts for the radxa rock3 model a")
Signed-off-by: Akash Gajjar <gajjar04akash@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip SoCs typically use U-Boot TPL to initialize DRAM, then jumps
back to BootRom to load next stage, U-Boot SPL, into DRAM. BootRom then
jumps to U-Boot SPL to continue the normal boot flow.
However, there is no support to initialize DRAM on RK35xx SoCs using
U-Boot TPL and instead an external TPL binary must be used to generate a
bootable u-boot-rockchip.bin image.
Add CONFIG_ROCKCHIP_EXTERNAL_TPL to indicate that an external TPL should
be used. Build U-Boot with ROCKCHIP_TPL=/path/to/ddr.bin to generate a
bootable u-boot-rockchip.bin image for RK3568.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Eugen Hristev <eugen.hristev@collabora.com>
The rk3328 sdram driver read sdram parameters from the devicetree into a
struct rk3328_sdram_params using dev_read_u32_array.
After commit 5ab30c3176 ("ram: rockchip: Update ddr pctl regs for px30")
changed the size of struct ddr_pctl_regs, a member of struct
rk3328_sdram_params, U-Boot TPL can no longer initialize DRAM on RK3328.
Add ten u32 to the sdram parameter array in devicetree to align with
this size change. This fixes DRAM initialization on RK3328.
Fixes: 5ab30c3176 ("ram: rockchip: Update ddr pctl regs for px30")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # roc-rk3328-cc
