When host issues "fastboot reboot fastboot", it's expected that the
board drops the USB connection before resetting.
On some boards, such as Khadas VIM3L and SEI610, this is not the case.
We observe the following error:
$ fastboot reboot fastboot
Rebooting into fastboot OKAY [ 0.004s]
fastboot: error: Failed to boot into userspace fastboot; one or more components might be unbootable.
This does not happen when we use the RST button on the board.
It can be reproduced in linux with:
# echo b > /proc/sysrq-trigger
In this case, we hit a undefined hardware behavior, where D+ and D-
are in an unknown state. Therefore the host can't detect usb
disconnection.
Make sure we always call usb_gadget_release() when a "fastboot reboot"
command is issued.
Note: usb_gadget_release() should be called before g_dnl_unregister()
because g_dnl_unregister() triggers a complete() call on each
endpoint (thus calling do_reset()).
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Remove unused ehci_{setup,shutdown}_phy() helpers now replaced by
generic_{setup,shutdown}_phy().
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Replace ehci_setup_phy() and ehci_shutdown_phy () by respectively
generic_setup_phy() and generic_shutdown_phy().
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Replace ohci_setup_phy() and ohci_shutdown_phy () by respectively
generic_setup_phy() and generic_shutdown_phy().
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
In drivers usb/host/{ehci,ohci}-generic.c, {ehci,ohci}_setup_phy() and
{ehci,ohci}_shutdown_phy() shares 95% of common code.
Factorize this code in new generic_{setup,shudown}_phy() functions.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Take the USB_ETHER ifdef block apart and make use of obj-$(VAR) instead
to include the source files in build. The duplicate CI_UDC entry is now
removed, the USB_DEVICE ifdef is now reduced to core.o ep.o addition,
the ether.o can be conditionally compiled in using USB_ETHER.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
- mtd: Update the function name to 'rfree'
- Support NAND ONFI EDO mode for imx8mn architecture
- dm: clk: add missing stub when CONFIG_CLK is deactivated
-----BEGIN PGP SIGNATURE-----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=VPkV
-----END PGP SIGNATURE-----
Merge tag 'u-boot-nand-20221009' of https://source.denx.de/u-boot/custodians/u-boot-nand-flash
- mtd: Update the function name to 'rfree'
- Support NAND ONFI EDO mode for imx8mn architecture
- dm: clk: add missing stub when CONFIG_CLK is deactivated
Instead of using DEBUG or LOG_DEBUG the driver still had its own
definition for debug output.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20221007122003.11239-11-ada@thorsis.com
Instead of using DEBUG or LOG_DEBUG the driver still had its own
definition for debug output.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20221007122003.11239-10-ada@thorsis.com
Instead of using DEBUG or LOG_DEBUG the driver still had its own
definition for debug output.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20221007122003.11239-9-ada@thorsis.com
Instead of using DEBUG or LOG_DEBUG the driver still had its own
definition for debug output.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20221007122003.11239-8-ada@thorsis.com
Instead of using DEBUG or LOG_DEBUG the driver still had its own
definition for debug output.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20221007122003.11239-7-ada@thorsis.com
Instead of using DEBUG or LOG_DEBUG the driver still had its own
definition for debug output.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20221007122003.11239-6-ada@thorsis.com
Warning appears if built with FPGA_DEBUG defined:
CC drivers/fpga/virtex2.o
/mnt/data/adahl/src/u-boot/drivers/fpga/virtex2.c: In function ‘virtex2_ssm_load’:
/mnt/data/adahl/src/u-boot/drivers/fpga/virtex2.c:333:11: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ {aka ‘long unsigned int’} [-Wformat=]
PRINTF("%s:%d:done went active early, bytecount = %d\n",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
__func__, __LINE__, bytecount);
~~~~~~~~~
/mnt/data/adahl/src/u-boot/drivers/fpga/virtex2.c:25:37: note: in definition of macro ‘PRINTF’
#define PRINTF(fmt, args...) printf(fmt, ##args)
^~~
/mnt/data/adahl/src/u-boot/drivers/fpga/virtex2.c: In function ‘virtex2_ss_load’:
/mnt/data/adahl/src/u-boot/drivers/fpga/virtex2.c:468:12: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ {aka ‘long unsigned int’} [-Wformat=]
PRINTF("%s:%d:done went active early, bytecount = %d\n",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
__func__, __LINE__, bytecount);
~~~~~~~~~
/mnt/data/adahl/src/u-boot/drivers/fpga/virtex2.c:25:37: note: in definition of macro ‘PRINTF’
#define PRINTF(fmt, args...) printf(fmt, ##args)
^~~
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20221007122003.11239-5-ada@thorsis.com
The additional comma messes up the arguments.
Warning appears if built with FPGA_DEBUG defined:
CC drivers/fpga/spartan3.o
/mnt/data/adahl/src/u-boot/drivers/fpga/spartan3.c: In function ‘spartan3_sp_load’:
/mnt/data/adahl/src/u-boot/drivers/fpga/spartan3.c:118:11: warning: too many arguments for format [-Wformat-extra-args]
PRINTF ("%s: Function Table:\n"
^~~~~~~~~~~~~~~~~~~~~~~
/mnt/data/adahl/src/u-boot/drivers/fpga/spartan3.c:18:37: note: in definition of macro ‘PRINTF’
#define PRINTF(fmt,args...) printf (fmt ,##args)
^~~
Fixes: 875c78934e ("Add Xilinx Spartan3 family FPGA support Patch by Kurt Stremerch, 14 February 2005")
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20221007122003.11239-4-ada@thorsis.com
That extra comma messes up format arguments.
Warning appears if built with FPGA_DEBUG defined:
CC drivers/fpga/spartan2.o
/mnt/data/adahl/src/u-boot/drivers/fpga/spartan2.c: In function ‘spartan2_sp_load’:
/mnt/data/adahl/src/u-boot/drivers/fpga/spartan2.c:112:11: warning: too many arguments for format [-Wformat-extra-args]
PRINTF ("%s: Function Table:\n"
^~~~~~~~~~~~~~~~~~~~~~~
/mnt/data/adahl/src/u-boot/drivers/fpga/spartan2.c:12:37: note: in definition of macro ‘PRINTF’
#define PRINTF(fmt,args...) printf (fmt ,##args)
^~~
CC drivers/fpga/spartan3.o
/mnt/data/adahl/src/u-boot/drivers/fpga/spartan3.c: In function ‘spartan3_sp_load’:
/mnt/data/adahl/src/u-boot/drivers/fpga/spartan3.c:117:11: warning: too many arguments for format [-Wformat-extra-args]
PRINTF ("%s: Function Table:\n"
^~~~~~~~~~~~~~~~~~~~~~~
/mnt/data/adahl/src/u-boot/drivers/fpga/spartan3.c:17:37: note: in definition of macro ‘PRINTF’
#define PRINTF(fmt,args...) printf (fmt ,##args)
^~~
Fixes: e221174377 ("Initial revision")
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20221007122003.11239-3-ada@thorsis.com
Fix the following sparse and compile time warning
triggered with W=1:
drivers/clk/clk_versal.c:605:5:
warning: no previous prototype for 'versal_clock_setup'
[-Wmissing-prototypes]
605 | int versal_clock_setup(void)
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20221007105535.31902-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Fix the following sparse and compile time warning triggered with W=1:
drivers/soc/soc_xilinx_zynqmp.c:288:5:
warning: no previous prototype for 'soc_xilinx_zynqmp_get_machine'
[-Wmissing-prototypes]
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20221004055201.26146-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support for imx8mn architecture in order to run the NAND
in fast edo mode.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Rename the gpmi_apb_bch clock name to gpmi_bch_apb, as you can find in
the device tree.
Fixes: commit a59691280d ("MXS_NAND: Add clock support for iMX8")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
This clock name is not present in any U-boot and Linux kernel device
tree.
Fixes: commit a59691280d ("MXS_NAND: Add clock support for iMX8")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Add gpmi nand clock. Those clock can be used in mxs nand driver
to run nand to EDO mode 5, 4, ...
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Add shared counter in order to avoid to swich off clock that
are already used.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
This fixes the below build error if nand.c is included in
an SPL build.
/work/u-boot/drivers/mtd/nand/raw/nand.c: In function ‘nand_init_chip’:
/work/u-boot/drivers/mtd/nand/raw/nand.c:82:28: error: ‘nand_chip’ undeclared (first use in this function)
82 | struct nand_chip *nand = &nand_chip[i];
| ^~~~~~~~~
/work/u-boot/drivers/mtd/nand/raw/nand.c:82:28: note: each undeclared identifier is reported only once for each function it appears in
/work/u-boot/drivers/mtd/nand/raw/nand.c:84:20: error: ‘base_address’ undeclared (first use in this function); did you mean ‘base_addr’?
84 | ulong base_addr = base_address[i];
| ^~~~~~~~~~~~
| base_addr
Fixes: 068c41f1cc ("Finish conversion CONFIG_SYS_NAND_SELF_INIT to Kconfig")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Fix the following sparse and compile time warning triggered with W=1:
drivers/spi/zynqmp_gqspi.c:286:6:
warning: no previous prototype for 'zynqmp_qspi_set_tapdelay'
[-Wmissing-prototypes]
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20221004053730.25602-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
For the TI SoCs affected by errata i2329, enable MDIO manual
mode by default
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
In certain TI SoCs, on the CPSW and ICSS peripherals, there is
a possibility that the MDIO interface returns corrupt data on
MDIO reads or writes incorrect data on MDIO writes. There is also
a possibility for the MDIO interface to become unavailable until
the next peripheral reset.
The workaround is to configure the MDIO in manual mode and disable the
MDIO state machine and emulate the MDIO protocol by reading and writing
appropriate fields in MDIO_MANUAL_IF_REG register of the MDIO controller
to manipulate the MDIO clock and data pins.
More details about the errata i2329 and the workaround is available in:
https://www.ti.com/lit/er/sprz487a/sprz487a.pdf
Add implementation to disable MDIO state machine, configure MDIO in manual
mode and provide software MDIO read and writes via MDIO bitbanging. Allow
the MDIO to be initialized based on the need for manual mode.
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Include linux/sizes.h because it defines SZ_64K which is used in many
places inside k3-udma.c
This fixes the error: ‘SZ_64K’ undeclared which appears during build
time
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On the 32bit ARM sandbox 'dm ut dm_test_devm_regmap' fails with an abort.
This is due to incorrect range checks.
On 32-bit systems the size of size_t and int is both 32 bit. The expression
(offset + val_len) is bound to overflow if offset == -1. Add an overflow
check.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move the code making sure that the timer is initialized only once into
orion_timer_init(), which is called from timer_early_init() and from
orion_timer_probe(). This way the timer is not re-initialized.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Michael Walle <michael@walle.cc>
Cc: Pali Rohár <pali@kernel.org>
Replace the if/else chain in pxa_ecc_init() with a lookup table. This
makes the code more concise and hopefully easier to follow. Remove the
unused ecc_layout tables and replace it with a single dummy one (the
pxa3xx driver has never used this but the mtd subsystem expects it to be
provided).
Tested on an Allied Telesis x530 switch with Micron MT29F2G08ABAEAWP
NAND Flash.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Firmware calls need node_id which is basically "power-domains" id.
At present static values are used based on the "device_id" property of
dt.
Instead of this, read "power-domains" id from dt and use it. Add a
element called node_id in priv structure and read it from dt. Replace
static node_id with this priv->node_id across the driver.
Since "device_id" is not used anywhere else simply remove it.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20220930092548.18453-3-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
In Versal platform power domain node_id is bigger than u8, hence
change prototype to u32 to accommodate. Change u8 to u32 in the function
prototypes that use node_id and remove casting to u32 from
xilinx_pm_request() call parameters.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20220930092548.18453-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Here are the smatch warning messages:
drivers/net/xilinx_axi_emac.c:324 axiemac_phy_init()
error: 'phydev' dereferencing possible ERR_PTR()
drivers/net/zynq_gem.c:340 zynq_phy_init()
error: 'priv->phydev' dereferencing possible ERR_PTR()
Fix by adding error checking before dereferencing the pointer.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20220929045605.23964-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The maximum length is capped similarly to the emaclite_send function.
Avoid integer underflow for values of ip->ip_len < 30, the minimum
length of an IP packet is 21 bytes.
Signed-off-by: Samuel Obuch <samuel.obuch@codasip.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Link: https://lore.kernel.org/r/20220927112103.155689-3-samuel.obuch@codasip.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Use __raw_read* and __raw_write* functions to ensure read/write
is passed to the memory-mapped regions, as non-volatile accesses
may get optimised out.
Signed-off-by: Samuel Obuch <samuel.obuch@codasip.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Link: https://lore.kernel.org/r/20220927112103.155689-2-samuel.obuch@codasip.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Function ioremap_nocache seems to be defined only for MIPS and Microblaze
architectures. Therefore, the function call in the emaclite driver causes
this driver to be unusable with other architectures, for example RISC-V.
Use ioremap function instead of ioremap_nocache, and include linux/io.h
instead of asm/io.h, so that ioremap function is automatically created,
if not defined by the architecture. We can switch to the ioremap function,
as Microblaze's ioremap_nocache is just empty and in MIPS implementations
of ioremap_nocache and ioremap are the same.
Signed-off-by: Samuel Obuch <samuel.obuch@codasip.com>
Link: https://lore.kernel.org/r/20220927112103.155689-1-samuel.obuch@codasip.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
To check dynamic loading of config object, currently APU_0 is used.
Suggestion from pmwfw team is to load OCM_BANK_0 and check for
XST_PM_NO_ACCESS error only to skip future config objects. Other errors
should not be considered for skipping. Change from NODE_APU_0 to
NODE_OCM_BANK_0 and check for XST_PM_NO_ACCESS to skip future config
objects.
Add ": " to printf statement when there is no permission to load config
object, to align with PMUFW version print.
Update kernel doc for return value for zynqmp_pmufw_load_config_object().
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/2784018844ba4afced0e3edff76bdbfe532f517d.1664523444.git.michal.simek@amd.com
For future DM based FPGA drivers and for now to have a meaningful
logging class for old FPGA drivers.
Suggested-by: Michal Simek <michal.simek@amd.com>
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Dahl <post@lespocky.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20220930120430.42307-2-post@lespocky.de
Signed-off-by: Michal Simek <michal.simek@amd.com>
At present ofnode_write_prop() is inconsistent between livetree and
flattree, in that livetree requires the caller to ensure the property
value is stable (e.g. in rodata or allocated) but flattree does not, since
it makes a copy.
This makes the API call a bit painful to use, since the caller must do
different things depending on OF_LIVE.
Add a new 'copy' argument which tells the function to make a copy if
needed. Add some tests to cover this behaviour.
Signed-off-by: Simon Glass <sjg@chromium.org>
We need to be able to look up phandles in any FDT, not just the control
FDT. Use the 'other' FDT to test this, with a helper function which gets
this as an oftree that can then we used as needed.
Add a few more tests and some comments at the top of the file, to explain
what is going on.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add the logic to redirect requests for the device tree through a function
which can look up the tree ID. This works by using the top bits of
ofnode.of_offset to encode a tree.
It is assumed that there will only be a few device trees used at runtime,
typically the control FDT (always tree ID 0) and possibly a separate FDT
to be passed the OS.
The maximum number of device trees supported at runtime is 8, with this
implementation. That would use bits 30:28 of the node-offset value,
meaning that the positive offset range is limited to bits 27:0, versus
30:1 with this feature disabled. That still allows a device tree of up
to 256MB, which should be enough for most FITs. Larger ones can be
supported by using external data with the FIT, or by enabling OF_LIVE.
Update the documentation a little and fix up the comment for
ofnode_valid().
Signed-off-by: Simon Glass <sjg@chromium.org>
At present, unless OF_LIVE is enabled, ofnode only supports access to one
device tree, the control FDT. This is because only the node offset is
encoded in ofnode, with the tree being implicit.
This makes ofnode (without OF_LIVE) unsuitable for device tree fixups, as
implemented by ft_board_setup() and other such functions.
To solve this, we can use the top bits of the node offset to hold a tree
ID.
Add the definitions for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function turns out to be a little confusing since it looks up a path
and also registers the tree. Split it into two, one that gets the root
node and one that looks up a path, so the purpose is clear.
Registering the tree will happen in a function to be added in a later
patch, called oftree_from_fdt().
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases we want to obtain an ofnode in the same tree as a different
ofnode, such as when looking up a subnode. At present this is trivial,
since there is only one tree. When there are multiple trees, this
implementation will change.
Also move the ofnode_to_offset() function up higher in the header file,
since we will need to provide a different implementation with multiple
trees.
Signed-off-by: Simon Glass <sjg@chromium.org>
When we have multiple trees, the ofnode logic needs to be told which one
to use. Create a new function which takes an oftree argument, along with
a helper to obtain the FDT pointer from an oftree.
Signed-off-by: Simon Glass <sjg@chromium.org>
The flat device tree is assumed to be the control FDT but this is not
always the case. Update the ofnode implementation to obtain the node via
an function call so we can eventually add support for selecting different
trees.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current tests do not cover all the behaviour. Add some more.
Tidy up a few inconsistencies between livetree and flattree which come to
light with these tests. Also drop the -ENODATA error since it is never
actually returned.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current implementation creates a 'name' value for every node. This
is not needed for the latest device tree format, which includes a name in
the node header.
Adjust the code to point the name at the node header instead.
Also simplify ofnode_get_name(), now that we can rely on it to set the
name correctly. Update the comment to make it clear what name the root
node has.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current name is quite unwieldy. Change it to use an ofprop_ prefix
and shorten it. Fix the return-value comment while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update the function to mark it with the const attribute. Also avoid
calling it multiple times in the devfdt_get_addr_index() function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that we support writing to ofnodes, the const is not accurate. Drop
it to avoid undesirable casting.
Also drop the ofnode_to_npw() which is now the same as ofnode_to_np().
Signed-off-by: Simon Glass <sjg@chromium.org>
Add this feature to the ofnode interface, supporting both livetree and
flattree. If the node exists it is returned, along with a -EEXIST error.
Update the functions it calls to handle this too.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function currently assumes that the control FDT is used. Update it
to allow a root node to be passed, so it can work with any tree.
Also add a comment to ofnode_get_by_phandle() so that its purpose is
clear.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the log functions instead of pr_...() so we can avoid using __func__.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This is not needed and we should avoid typedefs. Use the struct instead
and rename it to indicate that it really is a legacy struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
The udelay() function in lib/time.c contains a WATCHDOG_RESET()
call. So use __udelay() in max6370_wdt.c to prevent recursion.
Fixes: 0a095fc53b ("watchdog: Add MAX6370 watchdog timer driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The udelay() function in lib/time.c contains a WATCHDOG_RESET()
call. The only reason this doesn't lead to a catastrophic infinite
recursion is due to the rate-limiting in wdt-uclass.c:
if (time_after_eq(now, priv->next_reset)) {
priv->next_reset = now + priv->reset_period;
wdt_reset(dev);
}
But this would fall apart if ->next_reset was updated after calling the
device's reset method.
This is needlessly fragile, and it's easy enough to avoid that
recursion in the first place by just using __udelay() directly.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Stefan Roese <sr@denx.de>
xilinx:
- Add support for new Versal NET SOC
zynqmp:
- Use mdio bus for ethernet phy description
- Wire ethernet phy reset via i2c-gpio
versal:
- Config cleanup
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYzGwogAKCRDKSWXLKUoM
Ial4AJ9+4WHn0MV2X7gK1fyh4lUW7ggPhQCggsYlSoACgMgdji17SAPhCv/W3IA=
=BmA9
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2023.01-rc1-v2' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2023.01-rc1 (round 2)
xilinx:
- Add support for new Versal NET SOC
zynqmp:
- Use mdio bus for ethernet phy description
- Wire ethernet phy reset via i2c-gpio
versal:
- Config cleanup
Currently all GPIOs supported by CMD_EXT_CONTROL/CMD_GET_EXT_CONTROL_STATUS
commands (last 16 GPIOs) are available only when FEAT_PERIPH_MCU feature
bit is set. So do not register these GPIOs by U-Boot driver when this
feature bit is not set, so U-Boot 'gpio' command would see only GPIOs which
really exists.
Fixes: 5e4d24ccc1 ("gpio: Add Turris Omnia MCU driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
When processing USB_REQ_CLEAR_FEATURE, USB_REQ_SET_FEATURE, and
USB_REQ_GET_STATUS packets in dwc2_ep0_setup an out of bounds access
can occur. This is caused by the wIndex field of the usb control packet
being used as an index into an array whose size is DWC2_MAX_ENDPOINTS (4).
Signed-off-by: Alison Huffman <alisn@google.com>
At present sandbox is producing a warning about SCSI migration. Drop the
legacy code and replace it with a new implementation.
Also drop the SATA command, which does not work with driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this code out of the helper function so we can (later) add it as part
of the shared emulation code. Set a default value of 0 for buff_used since
that is what we use when there is an error.
Signed-off-by: Simon Glass <sjg@chromium.org>
In preparation for sharing the emulation code between two drivers, move
some of the fields into a new struct. Use a separate header file so it
can be used by various drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
This has the same name as a field in our local private struct, which is
confusing. Change the name to xfer_len instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Changing baudrate is a sensitive operation. To ensure that U-Boot messages
printed before changing baudrate are not lost, call new U-Boot console
flush() function.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Like in all other console functions, implement also serial_flush() function
as a fallback int console flush() function.
Flush support is available only when config option CONSOLE_FLUSH_SUPPORT is
enabled. So when it is disabled then provides just empty static inline
function serial_flush().
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
UART drivers have putc/puts functions which just put characters into HW
transmit queue and do not wait until all data are transmitted.
Implement flush callback via serial driver's pending(false) callback which
waits until HW transmit all characters from the queue.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
During init_dram() is called also compute_lowest_common_dimm_parameters()
function which prints multi-line detailed output. So print also re-aligning
filler after "Detected ?DIMM" line to have "DRAM: " output aligned.
Signed-off-by: Pali Rohár <pali@kernel.org>
U-Boot core code already handles the case when RAM size is bigger than
CONFIG_MAX_MEM_MAPPED. So there is no need to do duplicate check in fsl ddr
driver for CONFIG_MAX_MEM_MAPPED. Instead simplify code to just check if
RAM size can be representable in phys_size_t type. And avoid printing
warning if phys_size_t is just 1 byte smaller than RAM size, which is the
typical situation with 4 GB DDR module.
Signed-off-by: Pali Rohár <pali@kernel.org>
Function fsl_ddr_compute() always return size in unsigned long long type,
but function fsl_ddr_sdram_size() returns size in phys_size_t type.
When 36-bit addressing mode is not enabled then phys_size_t type is only
32-bit and thus it cannot store value 4GB (0x100000000). Function
fsl_ddr_sdram_size() in this case returns truncated value 0x0.
Fix this issue by returning the highest representable value, which is
0xffffffff (4GB - 1 byte).
This change fixes crashing of proper U-Boot because it detected 4 GB module
as RAM with zero size.
Signed-off-by: Pali Rohár <pali@kernel.org>
Check needs to be done against CONFIG_MAX_MEM_MAPPED macro and not fixed
size 4GB (as CONFIG_MAX_MEM_MAPPED can be lower and for example for e500
cores it is just 2GB). Also fix printf re-align, which should be applied
only for non-SPL builds, during init_dram() call.
Signed-off-by: Pali Rohár <pali@kernel.org>
Add basic CPU driver used to retrieve CPU model information.
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds clock driver support for MediaTek MT7981 SoC
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds clock driver support for MediaTek MT7986 SoC
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This adds the CLK_XTAL macro/flag to allow modeling clocks which are
directly connected to the xtal clock.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds infrasys clock mux support for mediatek clock drivers.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds support for a clock node to configure its parent clock
where possible.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The mtk clock framework in u-boot uses array index for searching clock
parent (kernel uses strings for search), so we need to specify a special
clock with ID=0 for CLK_XTAL in u-boot.
In the mt7622/mt7629 clock tree, the clocks with ID=0 never call
mtk_topckgen_get_mux_rate, adn return xtal clock directly. This what we
expected.
However for newer chips, they may have some clocks with ID=0 not
representing the xtal clock and still needs mtk_topckgen_get_mux_rate be
called. Current logic will make entire clock driver not working.
This patch adds a flag to indicate that whether a clock driver needs clocks
with ID=0 to call mtk_topckgen_get_mux_rate.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds pinctrl and gpio support for MT7986 SoC
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds pinctrl and gpio support for MT7981 SoC
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds support for MediaTek I2C interface
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds support for spi-mem controller found on newer MediaTek SoCs
This controller supports Single/Dual/Quad SPI mode.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
Add watchdog support for MediaTek MT7986 SoC
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch add general-purpose timer support for MediaTek MT7981/MT7986.
These two SoCs uses a newer version of timer with its register definition
slightly changed.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds PWM support for MediaTek MT7981 SoC.
MT7981 uses a different register offset so we have to add a version field
to indicate the IP core version.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The baud clock on some platform may change due to assigned-clock-parent
set in DT. In current flow the baud clock is only retrieved during probe
stage. If the parent of the source clock changes after probe stage, the
setbrg will set wrong baudrate.
To get the right clock rate, this patch records the baud clk struct to the
driver's priv, and changes the driver's flow to get the clock rate before
calling _mtk_serial_setbrg().
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds support for MediaTek MT7981 and MT7986. Both chips uses
PDMA v2.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds support for PDMA v2 hardware. The PDMA v2 has extended the
DMA descriptor to 8-words, and some of its fields have changed comparing
to the v1 hardware.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch is a preparation for adding a new version of PDMA of which the
DMA descriptor fields has changed. Using bitfields will result in a complex
modification. Convert bitfields to u32 units can solve this problem easily.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Using a single soc id to control different initialization and TX/RX flow
for all SoCs is not extensible if more hardware variations are added in
the future.
This patch introduces a struct to replace the original mtk_soc to allow
the driver be able handle newer hardwares.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add eMMC and SDXC support for MediaTek MT7981/MT7986 SoCs
Both chips support SDXC and eMMC 4.5. MT7986A supports eMMC 5.1.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmMoEdgcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyNvEB/4nEeiBx7Lo1gK+79PJ
9kCUngglHRu3/+FJMpcOp+2b6sSW1IZs8qGBMAMFSRoFElrLMMbVEgBR0ZfJCl3c
It0xN9Buhe8muwtAdE8Amr4PddUEynzglVPpFUFfir6ZqFAcedmN6iuh+K82r7Be
7s/8tRb2hVp//TpkEntf2yxrYnyeW4qiXyUxbUhaUyyhkM3RBXySuY4qnaaLp3NY
R9rsIY5j3kA2QylebEamlXI+KDvszrGbkUOUUrlwkygQNR/GmAYQPlY1TdBwk0wE
U1CO8zQYaL3OY998lU32pMVClmwyXbn2i7KAyMm3TEgrfpjQsLTS2BK+w+RBdMGL
XGnt
=lRvM
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2023.01-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2023.01 cycle:
This feature set includes the important update on PIO4 pinctrl driver
that solves a long time mismatch between Linux and U-boot, related on
the unification of pinctrl and gpio driver support, now respecting the
pinctrl bindings ABI; and also support for pinctrl subnodes. The feature
set also adds support for PDA screen detection for sam9x60_curiosity
board , one fix for SD-Card reinsertion and one fix for sam9x60 clocks.
Add timer_get_boot_us() to support boards, that have CONFIG_BOOTSTAGE
enabled, like pogo_v4.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Tony Dinh <mibodhi@gmail.com>
This patch adds support for other Marvell Armada SoC's, supporting the
25MHz fixed clock operation, like the Armada XP etc.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Tony Dinh <mibodhi@gmail.com>
This driver is not used by any system and is long unmaintained, drop it.
There is a DWC2 OTG driver which is maintained, see CONFIG_USB_GADGET_DWC2_OTG .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Previously, in order for the `pinctrl-*` DT node properties
to be properly processed, the pinctrl's subnodes were limited
to only having the `pinmux` property as well as other additional
properties (slew-rate, bias-disable, etc.). Now, with this patch
the pinctrl driver is made to work similarly to the one from Linux.
It can now distinguish between one subnode and a subnode with multiple
subnodes.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
This has been done in order to align the DT of U-Boot with the DT
of Linux. In Linux, a phandle from a '-gpio' DT property is linked
to the pinctrl driver, a single driver that handles both pinctrl
settings and offers GPIO API to callers. On the other hand,
U-Boot redirects such phandle to a corresponding UCLASS_GPIO
driver, because U-Boot offers two different types of drivers
in this case: UCLASS_PINCTRL which handles pin functions and
UCLASS_GPIO which handles gpio requests as a gpio provider.
Due to this, we have two drivers in Uboot, but the Devicetree
has a single node. Thus, just one of the drivers can be probed
for the DT node during platform initialization, before relocation.
Our previous solution in U-Boot was to have a different devicetree:
the gpio node has a subnode for the pinctrl driver, which
is not compliant with Linux ABI. Furthermore, our documentation
for this type of nodes mentions no such gpio compatible.
After this patch, we can no longer add nodes with a gpio
compatible in the DT. Thus, in order to link the pinctrl driver to
the gpio one, a hook to the bind method of the former in U-Boot has
been added and the GPIO related compatibles have been removed to
avoid conflict when compatibles are enumerated and bound to drivers
during platform start before relocation. The bind method will attach
the GPIO driver to the pinctrl DT node so that every phandle coming
from '-gpio' DT properties will be redirected to a valid driver
attached to the pinctrl DT node.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
ddrck and qspick should have mck_div as parent clocks to be in sync with
linux driver.
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Whenever the SD Card would be removed and then re-inserted while in the
U-Boot command line, the `SDBPWR` bit of the `SDMMC_PCR` register would
remain unset afterwards. In order for the bit to be set again after
re-insertion, register an additional `deferred_probe` method that the
DM would then transparently call. This method will call the generic
`sdhci_probe` which will, during its execution flow, set this bit to 1.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Reported-by: Mihai Sain <mihai.sain@microchip.com>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
only waiting for TXEMPTY leads to corrupted messages going over the
wire - which is fixed by making use of the FIFO
this change is following the linux kernel uart driver
(drivers/tty/serial/imx.c), which also checks UTS_TXFULL
instead of UTS_TXEMPTY
Signed-off-by: Johannes Schneider <johannes.schneider@leica-geosystems.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
on imx8(mm) the RXDMUXSEL needs to be set for data going over the wire
(as observable on a connected 'scope) to actually make it into the
RXFIFO
the reference manual is not overly clear about this, and only
mentiones that "UCR3_RXDMUXSEL should always be set." - and since the
CR3 register reverts to its reset values after setting the baudrate,
setting this bit is done during '_mxc_serial_setbgr'
Signed-off-by: Johannes Schneider <johannes.schneider@leica-geosystems.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The ddrphy_utils.c is now deduplicated in drivers/ddr/imx/phy/ddrphy_utils.c ,
this drivers/ddr/imx/imx8m/ddrphy_utils.c is a remnant from when the
deduplication was implemented and was not removed. Remove it as it is
unused.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
wrong end address passed to flush_dcache_range.
modified the flush_dache logic for scatter list elements.
Fixes: 1919f58a8f (crypto/fsl: fsl_hash: Fix dcache issue in caam_hash_finish)
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
The i.MXRT11 series has different offsets for IOCR_MUX, it also can
address 64MiB of SDRAM so add a macro for that.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
The i.MXRT11 series has two new pll types but are variants of existing.
This patch adds the ability to read one of the pll types' frequency
as it can't be changed unlike the generic pll it also has the
division factors swapped.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
While testing on some Kirkwood platforms it was noticed that the timer
did not function correctly all the time. The driver did not correctly
handle 32bit timer value wrap arounds. Using the timer_conv_64()
conversion function fixes this issue.
Fixes: e9e73d78a8 ("timer: add orion-timer support")
Suggested-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier-oss@weidmueller.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Globally replace all occurances of WATCHDOG_RESET() with schedule(),
which handles the HW_WATCHDOG functionality and the cyclic
infrastructure.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
This patch integrates the watchdog triggering into the recently added
cyclic infrastructure. Each watchdog device that shall be triggered
registers it's own cyclic function. This way, multiple watchdog devices
are still supported, each via a cyclic function with separate trigger
intervals.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
When fixed offset via CONFIG_SYS_MMC_U_BOOT_OFFS is not specified then
expects that U-Boot proper is placed immediately after SPL without any
additional padding.
This allows to generate smaller SPL+U-Boot final binary as it is not
required to specify fixed offset to U-Boot proper at SPL compile time.
In this case offset to U-Boot proper is calculated at SPL compile time in
linker script.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
This allows to concatenate SPL and proper U-Boot without extra alignment.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
We currently have an if_type (interface type) and a uclass id. These are
closely related and we don't need to have both.
Drop the if_type values and use the uclass ones instead.
Maintain the existing, subtle, one-way conversion between UCLASS_USB and
UCLASS_MASS_STORAGE for now, and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
These are currently using a simple array lookup in one direction, and
relying on if_type being sequential.
With the move to uclass IDs this needs to change. Update the code to
prepare for the new way. This patch is intended to introduce no
functional change.
The returning of "(none)" from blk_get_if_type_name() is handling a case
that should not happen in either case.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we use a variable with the same name as the enum. Change this
since we plan to #define the enum to uclass_id.
Signed-off-by: Simon Glass <sjg@chromium.org>
This doesn't seem to be used for anything and it isn't clear what it is.
It dates from the first U-Boot commit.
Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
We don't want boards to be able to change these. They can be handled
as dependencies of options that need them, such as SPL_MMC. There is no
point in enabling the block interface without any storage devices to
create a block device.
Hide both options from the 'menuconfig' display and deny their use in
defconfig files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Selecting this option can be handled in the Kconfig option itself, as it
is with BLK. Update this an drop the various 'select' clauses.
Signed-off-by: Simon Glass <sjg@chromium.org>
This option is fact really related to SPL. For U-Boot proper we always use
driver model for block devices, so CONFIG_BLK is enabled if block devices
are in use.
It is only for SPL that we have two cases:
- SPL_BLK is enabled, in which case we use driver model and blk-uclass.c
- SPL_BLK is not enabled, in which case (if we need block devices) we must
use blk_legacy.c
Rename the symbol to SPL_LEGACY_BLOCK to make this clear. This is
different enough from BLK and SPL_BLK that there should be no confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we use HAVE_BLOCK_DEVICE to indicate when block devices are
available.
This is a very strange option, since it partially duplicates the BLK
option used by driver model. It also covers both U-Boot proper and SPL,
even though one might have block devices and another not.
As a first step towards correcting this, create a new inline function
called blk_enabled() which indicates if block devices are available.
This cannot be used in Makefiles, or #if clauses, but can be used in C
code.
A function is useful because we cannot use CONFIG_IS_ENABLED(BLK) to
decide if block devices are needed, since we must consider the legacy
block interface, enabled by HAVE_BLOCK_DEVICE
Update a few places where it can be used and drop some unnecessary #if
checks around some functions in disk/part.c - rely on the compiler's
dead-code elimination instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present these files have an #ifdef covering the whole file. Move the
condition to the Makefile instead.
Add BLK to the condition since future patches will adjust things so that
HAVE_BLOCK_DEVICE is only for SPL, but the partition drivers are needed
in U-Boot proper too.
Signed-off-by: Simon Glass <sjg@chromium.org>
The _SUPPORT suffix should be dropped. This happened because the rename
was applied around the same time as this new option, so did not include
renaming the new option.
The relevant commits are:
f7560376ae sata: Rename SATA_SUPPORT to SATA
73059529b2 ata: ahci-pci: Add new option CONFIG_SPL_AHCI_PCI
Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable this option on all boards which support block devices. Drop the
related depencies on BLK since these are not needed anymore.
Disable BLOCK_CACHE on M5253DEMO as this causes a build error.
Signed-off-by: Simon Glass <sjg@chromium.org>
This allows to test if a pin's label if displayed using gpio_get_status()
when this pin is configured in alternate function.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Even pin with GPIOF_UNUSED function can have a label.
The criteria to add or not a space character is linked to label not to
the used/unused status.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The bar of the structure virtio_pci_cap is the index, and each base
address occupies 4 bytes, so it needs to be multiplied by 4.
This patch fixes a bug reported by Felix Yan
https://lists.denx.de/pipermail/u-boot/2022-August/492779.html
Signed-off-by: Xiang W <wxjstz@126.com>
Tested-by: Felix Yan <felixonmars@archlinux.org>
The nvme driver falsely assumed that the last entry on a page
of the prp-list always points to the next page of the prp-list.
This potentially can lead to the illegal creation of pages on
the prp-list with only a single entry. This change now ensures
that splitting the prp-list into multiple pages, behaves now as
required by the NVME-Spec.
Related to this, also the size of the memory allocation is adjusted
accordingly.
Signed-off-by: Alexander Sowarka <alexander.sowarka@aerq.com>
These two device tree properties were not being applied.
Fixes: 1fd9eb68d6 ("i2c: stm32f7: move driver data of each instance in a privdata")
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Current function stm32_i2c_message_xfer is sending a STOP
whatever the result of the transaction is. This can cause issues
such as making the bus busy since the controller itself is already
sending automatically a STOP when a NACK is generated.
Thanks to Jorge Ramirez-Ortiz for diagnosing and proposing a first
fix for this. [1]
[1] https://lore.kernel.org/u-boot/20220815145211.31342-2-jorge@foundries.io/
Reported-by: Jorge Ramirez-Ortiz, Foundries <jorge@foundries.io>
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Functions stm32_i2c_message_start and stm32_i2c_handle_reload
both get a stop boolean indicating if the transfer should end with
a STOP or not. However no specific handling is needed in those
functions hence remove the parameter.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Comment within stm32_i2c_message_start is misleading, indicating
that AUTOEND bit is setted while it is actually cleared.
Moreover, the bit is actually never setted so there is no need
to clear it hence get rid of this bit clear and the bit macro
as well.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Bits should be set to 0, not 1.
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Changes optee_rng driver to register itself has a OP-TEE service so
that a device is bound for the driver when OP-TEE enumerates the
PTA RNG service.
Cc: Sughosh Ganu <sughosh.ganu@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This change defines resources for OP-TEE service drivers to register
themselves for being bound to when OP-TEE firmware reports the related
service is supported. OP-TEE services are discovered during optee
driver probe sequence which mandates optee driver is always probe once
bound.
Discovery of optee services and binding to related U-Boot drivers is
embedded upon configuration switch CONFIG_OPTEE_SERVICE_DISCOVERY.
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Removes local variable child in optee_probe() that is not used.
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
The device tree binding [1] specify the vendor-id, product-id, device-id
and language-id as 16 bit values and the linux driver reads the boost-up
value as 8 bit value.
[1] https://www.kernel.org/doc/Documentation/devicetree/bindings/usb/usb251xb.txt
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add functions to read 8/16-bit integers like the existing functions for
32/64-bit to simplify read of 8/16-bit integers from device tree
properties.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add ID for Winbond W25Q512JVQ device which is supported
on AST2600 EVB by default.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Driver can configure the SPI clock frequnecy to the
target value of "spi-max-frequency" property in
the device tree. The frequency is divided from HCLK,
200MHz. Usually, the ASPEED SPI clock frequency range
is between 12.5MHz and 100MHz. On AST2600, the lowest
SPI clock frequency can be about 780kHz.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
If "decoded-ranges" is defined in the device tree, the
driver will apply the decoded address ranges from this
property to the controller during probe stage.
This patch refers to the following OpenBMC u-boot patch.
https://patchwork.ozlabs.org/project/openbmc/list/?series=306969
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
There are some known HW problems about decoded
range register configurations on existing AST2500 and
AST2600 platforms. Additional callback function,
adjust_decoded_sz, is added to solve these problems
on each platform. Besides, aspeed_spi_trim_decoded_size
function is added to modify overall decoded address
size for fitting the maximum AHB decoded size.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
From the HW point of view, the performance of
command read mode is greater than user mode slightly.
Thus, dirmap read framework is introduced to achieve
this goal. In dirmap_create, command read mode is
configured. Usually, the decoded address area with flash
size is assigned to each CS. CPU can thus access the
SPI flash as normal memory in dirmap_read function.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
This adds support for the dirmap API to the spi-nor subsystem, as
introduced in Linux commit df5c21002cf4 ("mtd: spi-nor: use
spi-mem dirmap API").
This patch is synchronize from the following patch
https://patchwork.ozlabs.org/project/uboot/patch/20210205043924.149504-4-seanga2@gmail.com/
The corresponding Linux kernel SHA1 is df5c21002cf4.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
This adds the dirmap API originally introduced in
Linux commit aa167f3fed0c
("spi: spi-mem: Add a new API to support direct mapping").
This also includes several follow-up patches and fixes.
Changes from Linux include:
* Added Kconfig option
* Changed struct device to struct udevice
* Changed struct spi_mem to struct spi_slave
This patch is obtained from the following patch
https://patchwork.ozlabs.org/project/uboot/patch/20210205043924.149504-3-seanga2@gmail.com/
The corresponding Linux kernel SHA1 is aa167f3fed0c.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Although AST2400 is EOL officially, in order to achieve
sustainability and completeness, AST2400 part is added.
For AST2400,
- Five CSs are supported by FMC controller.
- SPI1 controller only supports single CS and there is
no address segment address register. The CE control
register of SPI1 is located at the offset 0x04 and
the 4-byte address mode control bit is bit 13 of
this register.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Add ASPEED BMC FMC/SPI memory controller driver with
spi-mem interface for AST2500 and AST2600 platform.
There are three SPI memory controllers embedded in an ASPEED SoC.
- FMC: Named as Firmware Memory Controller. After AC on, MCU ROM
fetches initial device boot image from FMC chip select(CS) 0.
- SPI1: Play the role of a SPI Master controller. Or, there is a
dedicated path for HOST(X86) to access its BIOS flash mounted
under BMC. spi-aspeed-smc.c implements the control sequence when
SPI1 is a SPI master.
- SPI2: It is a pure SPI flash controller. For most scenarios, flashes
mounted under it are for pure storage purpose.
ASPEED SPI controller supports 1-1-1, 1-1-2 and 1-1-4 SPI flash mode.
Three types of command mode are supported, normal mode, command
read/write mode and user mode.
- Normal mode: Default mode. After power on, normal read command 03h or
13h is used to fetch boot image from SPI flash.
- AST2500: Only 03h command can be used after power on
or reset.
- AST2600: If FMC04[6:4] is set, 13h command is used,
otherwise, 03h command.
The address length is decided by FMC04[2:0].
- Command mode: SPI controller can send command and address
automatically when CPU read/write the related remapped
or decoded address area. The command used by this mode
can be configured by FMC10/14/18[23:16]. Also, the
address length is decided by FMC04[2:0]. This mode will
be implemented in the following patch series.
- User mode: It is a traditional and pure SPI operation, where
SPI transmission is controlled by CPU. It is the main
mode in this patch.
Each SPI controller in ASPEED SoC has its own decoded address mapping.
Within each SPI controller decoded address, driver can assign a specific
address region for each CS of a SPI controller. The decoded address
cannot overlap to each other. With normal mode and command mode, the
decoded address accessed by the CPU determines which CS is active.
When user mode is adopted, the CS decoded address is a FIFO, CPU can
send/receive any SPI transmission by accessing the related decoded
address for the target CS.
This patch only implements user mode initially. Command read/write
mode will be implemented in the following patches.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Add FWSPICS1 and SPI1CS1 in AST2500 pinctrl group.
On AST2500 EVB, FWSPICS1 can be supported by default.
An extra jumper, J45, should be configured before
enabling SPI1CS1.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
User can get correct HCLK frequency during driver probe stage
by adding the following configuration in the device tree.
"clocks = <&scu ASPEED_CLK_AHB>".
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Few lines are extented to next line though they can fit in 80 character
limit, align them to single line. No functional change.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20220825125906.11581-6-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
As the flash sizes are increasing day by day, QSPI can have devices of
size > 512MB. In qspi driver we are trying to read all the data at once
using DMA.
The DMA descriptor destination size is only 29bits long.
QSPIDMA_DST_SIZE 0xFF0F0804
BITS: 1:0 Reserved to keep word alignment
BITS: 28:2 Number of 4-byte words the DMA will transfer
BITS: 31:29 Reserved: Returns 0 when read, writes ignored
So we can only transfer data of 0x1FFFFFF0(512MB minus 4bytes) bytes.
Anything above will overflow this register and will ignore higher bits
above 29 bits.
Change the DMA functionality if the requested size is greater than or
equal to 512MB to read 256MB chunks.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20220825125906.11581-5-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support for io-mode transfers. This is necessary for UBIFS to work
properly with spi-nor devices. The driver will work in IO mode when
"has-io-mode" is passed from device tree instead of DMA.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20220825125906.11581-4-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
As per driver model we should enumerate plat structure only in
of_to_plat() and should be used only in probe(). Copy required
plat structure info into priv structure in probe() and use priv
structure across the driver. So replace plat with priv structure across
the driver.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220824113847.7482-4-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
In cadence_spi_read_id we are using STIG mode to read flash id's.
Call cadence_qspi_apb_command_read_setup() to setup cmd, addr and data
bus width properly before cadence_qspi_apb_command_read().
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220824113847.7482-3-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
In cadence_spi_probe, cadence_qspi_versal_flash_reset() is called to reset
the flash device. Looks like there is a mistake in previous series of
patches where it is defined as cadence_spi_versal_flash_reset() but
called as cadence_qspi_versal_flash_reset. Since there is a weak function
defined with the same name this issue was not caught.
Fix the issue by renaming cadence_spi_versal_flash_reset as
cadence_qspi_versal_flash_reset().
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220824113847.7482-2-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Check snprintf() return value for errors.
Make microblaze_cpu_get_desc() directly return snprintf() error code if
ret < 0. Otherwise, if the return value is greater than or equal to size,
the resulting string is truncated, so return -ENOSPC.
Fixes: 816226d27e ("cpu: add CPU driver for microblaze")
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220829170205.1274484-2-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The drivers informs the user that a post config was not run after FPGA
configuration. This message is unnecessary in SPL because the
ps7_post_config function is called via spl_board_prepare_for_boot
function before jump_to_image_no_args function from board_init_r
function.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Link: https://lore.kernel.org/r/20220808145331.24723-1-stefan.herbrechtsmeier-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
