JESD216D-01 mentions that "defaults to 3-Byte mode; enters 4-Byte mode on
command."
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add flash info table entries for s28hl512gt, s28hl01gt, and s28hs01gt.
These devices have the same functionality as s28hs512t.
In spi-nor-core, use device ID byte to detect S28 family instead of
device name.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Change configuration macro name to support all other devices in SEMPER S28
family.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Change prefix to support all other devices in SEMPER S28 family.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add gpio driver for ADP5585 I/O Expander Controller. The ADP5585 is a 10
input/output port expander and can be used to increase the number of
I/Os available to a processor.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Update the ftgmac100 driver to support NC-SI instead of an mdio phy
where available. This is a common setup for Aspeed AST2x00 platforms.
NC-SI mode is determined from the device-tree if either phy-mode sets it
or the use-ncsi property exists. If set then normal mdio setup is
skipped in favour of the NC-SI phy.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add the handling of NC-SI ethernet frames, and add a check at the start
of net_loop() to configure NC-SI before starting other network commands.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
There are no platforms that have not migrated to using DM_KEYBOARD,
remove the legacy option.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There are no longer any platforms which do not enable DM, move this to a
def_bool y and remove the check in the Makefile.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
issue:
CAAM fails with key error when perform Modular Exponentiation
using PKHA Block in CAAM
Fix:
add flush and invalidate dcache for keys, signature
and output decrypted data processed by CAAM.
Fixes: 34276478f7 (DM: crypto/fsl - Add Freescale rsa DM driver)
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
The QSPI clocks are only used when CONFIG_NXP_FSPI=y, so only build the
QSPI clocks in this case to reduce the final SPL binary size.
Signed-off-by: Fabio Estevam <festevam@denx.de>
The ecspi clocks are only used when CONFIG_DM_SPI=y, so only build the
ecspi clocks in this case to reduce the final SPL binary size.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Ethernet is not used inside SPL, so move the IMX8MM_CLK_ENET_AXI clock
inside the non-SPL block to reduce the final SPL binary size.
Signed-off-by: Fabio Estevam <festevam@denx.de>
PWM is not used inside SPL, so do not define the PWM clocks inside
SPL to reduce the final SPL binary size.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Move init_clk_usdhc to non-clk driver case, since assigned-clocks properties
will initialize the clocks by clk driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
- dts update and sync for rk356x, rk3288, rk3399 from Linux;
- Add rk3399 EAIDK-610 board support;
- Update for puma-rk3399 board;
- some fix and typo fix in different drivers;
This contains various fixes (some long overdue) for the next release.
-----BEGIN PGP SIGNATURE-----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=H1Iz
-----END PGP SIGNATURE-----
Merge tag 'clk-2023.01' of https://source.denx.de/u-boot/custodians/u-boot-clk
Clock patches for 2023.01
This contains various fixes (some long overdue) for the next release.
Beside some rather unexciting sync of the DTs from the kernel tree, and
some Kconfig cleanup, there are some improvements for the ARMv5 Allwinner
family, to support boards with the F1C200s (64MB DRAM) better. We will
get actual board support as soon as the DTs have passed the Linux review
process.
There is also support for the X96 Mate TV Box, featuring the H616 SoC and
a full 4GB of DRAM.
Also we found the secret to enable SPI booting on the H616 (pin PC5 must
be pulled to GND), so the SPI boot support patch is now good to go.
Passed the gitlab CI, plus briefly tested on Pine64-LTS, LicheePi Nano,
X96 Mate and OrangePi Zero.
The k210 driver is selected by sandbox_defconfig.
Building the sandbox on 32bit systems fails with:
test/dm/k210_pll.c: In function ‘dm_test_k210_pll_calc_config’:
include/linux/bitops.h:11:38: warning:
left shift count >= width of type [-Wshift-count-overflow]
11 | #define BIT(nr) (1UL << (nr))
| ^~
test/dm/k210_pll.c:36:54: note: in expansion of macro ‘BIT’
36 | error = abs((error - BIT(32))) >> 16;
| ^~~
Use the BIT_ULL() macro to create a u64 value.
Replace abs() by abs64() to get correct results on 32bit system
Apply the same for the unit test.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
All functions getting and setting clock rate use ulong for rate, only
clk_get_parent_rate is an exception. Change the return value to match
other clock rate funcrions.
Most users directly assign the rate to unsigned long anyway, and the few
users that use u64 (not s64) multiply the rate so they may need the
extra bits for the result in their use case.
Fixes: 4aa78300a0 ("dm: clk: Define clk_get_parent_rate() for clk operations")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20220928103757.11870-1-msuchanek@suse.de
Some boards with the Allwinner F1C100s family SoCs use UART1 for its
debug UART, so define the pins for the SPL and the pinmux name and mux
value for U-Boot proper.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
RAM_PX30_DDR4 is for DDR4 support and not DDR3 so let's fix the typo.
Fixes: 2db36c64bd ("ram: rockchip: px30: add a config-based ddr selection")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The original code set up the DDR clock to 48 MHz, not 50MHz as
requested, and did it in a way that didn't satisfy the Application
Notes in RK3399 TRM [1]. 2.9.2.B says:
PLL frequency range requirement
[...]
FOUTVCO: 800MHz to 3.2GHz
2.9.2.A :
PLL output frequency configuration
[...]
FOUTVCO = FREF / REFDIV * FBDIV
FOUTPOSTDIV = FOUTVCO / POSTDIV1 / POSTDIV2
FREF = 24 MHz
The original code gives FOUTVCO: 24MHz/1 * 12 = 288MHz < 800MHz
And the resulting FOUTPOSTDIV is 288MHz / 3 / 2 = 48MHz
but the requested frequency was 50MHz
Note:
2.7.2 Detail Register Description
PMUCRU_PPLL_CON0 says
fbdiv
Feedback Divide Value
Valid divider settings are:
[16, 3200] in integer mode
So .fbdiv = 12 wouldn't be right. But 2.9.2.C says:
PLL setting consideration
[...]
The following settings are valid for FBDIV:
DSMPD=1 (Integer Mode):
12,13,14,16-4095 (practical value is limited to 3200, 2400, or 1600
(FVCOMAX / FREFMIN))
[...]
So .fbdiv = 12 would be right.
In any case FOUTVCO is still wrong. I thank YouMin Chen for
confirmation and explanation.
Despite documentation, I don't seem to be able to reproduce a
practical problem with the wrong FOUTVCO. When I initially found it I
thought some problems with detecting the RAM capacity in my Rock Pi 4B
could be related to it and my patch seemed to help. But since I'm no
longer able to reproduce the issue, it works with or without this
patch. And meanwhile a patch[2] by Lee Jones and YouMin Chen addresses
this issue. Btw, shouldn't that be commited?
So this patches solves no visible problem. Yet, to prevent future
problems, I think it'd be best to stick to spec.
An alternative to this patch could be
{.refdiv = 1, .fbdiv = 75, .postdiv1 = 6, .postdiv2 = 6};
This would theoretically consume more power and yield less jitter,
according to 2.9.2.C :
PLL setting consideration
[...]
For lowest power operation, the minimum VCO and FREF frequencies
should be used. For minimum jitter operation, the highest VCO and
FREF frequencies should be used.
[...]
But I haven't tried it because I don't think it matters much. 50MHz
for DDR is only shortly used by TPL at RAM init. Normal operation is
at 800MHz. Maybe it's better to use less power until later when more
complex software can control batteries or charging or whatever ?
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@vrull.eu>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Sean Anderson <seanga2@gmail.com>
Link: [1] https://opensource.rock-chips.com/images/e/ee/Rockchip_RK3399TRM_V1.4_Part1-20170408.pdf
Link: [2] https://patchwork.ozlabs.org/project/uboot/list/?series=305766
Signed-off-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Tested-by: Michal Suchánek <msuchanek@suse.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
All of the required values for using the omap_wdt.c driver are found in
<asm/ti-common/omap_wdt.h> and this is what is indirectly pulled in via
<asm/arch/hardware.h> when it exists.
Signed-off-by: Tom Rini <trini@konsulko.com>
DMA operations should function on DMA addresses, not virtual addresses.
Although these are usually the same in U-Boot, it is more correct
to be explicit with our types here.
Signed-off-by: Andrew Davis <afd@ti.com>
We should clean the caches before any DMA operation and clean+invalidate
after. This matches what the DMA framework does for us already but adds
it to the two functions here in this driver that don't yet go through the
new DMA framework.
Signed-off-by: Andrew Davis <afd@ti.com>
The DMA'd memory area needs cleaned and invalidated after the DMA
write so that any stale cache lines do not mask new data.
Signed-off-by: Andrew Davis <afd@ti.com>
Add support for j784s4-wiz-10g device which has two core reference
clocks (e.g core_ref_clk, core_ref1_clk) which requires an additional
mux selection option.
Signed-off-by: Matt Ranostay <mranostay@ti.com>
The _err variant iterators use the simple iterators without suffix as
basis.
However, there is no user that uclass_next_device_err for iteration,
many users of uclass_first_device_err use it to get the first and
(assumed) only device of an uclass, and a couple that use
uclass_next_device_err to get the device following a known device in the
uclass list.
While there are some truly singleton device classes in which more than
one device cannot exist these are quite rare, and most classes can have
multiple devices even if it is not the case on the SoC's EVB.
In a later patch the simple iterators will be updated to not stop on
error and return next device instead. With this in many cases the code
that expects the first device or an error if it fails to probe may get
the next device instead. Use the _check iterators as the basis of _err
iterators to preserve the old behavior.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The return value is not used for anythig, and in a later patch the
behavior of the _err iterator will change in an incompatible way.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update pvblock_probe() to avoid using internal var:
Signed-off-by: Simon Glass <sjg@chromium.org>
blk_first_device_err/blk_next_device_err uses
uclass_first_device_err/uclass_next_device_err for device iteration.
Although the function names superficially match the return value from
uclass_first_device_err/uclass_next_device_err is never used
meaningfully, and uclass_first_device/uclass_next_device works equally
well for this purpose.
In the following patch the semantic of
uclass_first_device_err/uclass_next_device_err will be changed to be
based on uclass_first_device_check/uclass_next_device_check breaking
this sole user that uses uclass_next_device_err for iteration.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is a number of users that use uclass_first_device to access the
first and (assumed) only device in uclass.
Some check the return value of uclass_first_device and also that a
device was returned which is exactly what uclass_first_device_err does.
Some are not checking that a device was returned and can potentially
crash if no device exists in the uclass. Finally there is one that
returns NULL on error either way.
Convert all of these to use uclass_first_device_err instead, the return
value will be removed from uclass_first_device in a later patch.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use uclass_first_device_check/uclass_next_device_check to correctly
count buses that fail to probe.
Fixes: d3e19cf919 ("w1: Add 1-Wire uclass")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The code checks that uclass_first_device returned a device but the
returned value that is assigned is never used. Use
uclass_first_device_err instead, and move the error return outside of
the if block.
Fixes: f4ec1ae08e ("mxc_ipuv3_fb.c: call display_enable")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The code checks the return value from uclass_first_device as well as
that the device exists but it passes on the return value which may be
zero if there are no gadget devices. Just check that a device was
returned and return -ENODEV otherwise.
Also remove the dev variable which is not really used for anything.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
When there is no PCI bus uclass_first_device will return no bus and no
error which will result in pci_find_first_device calling
skip_to_next_device with no bus, and the bus is only checked at the end
of the while cycle, not the beginning.
Fixes: 76c3fbcd3d ("dm: pci: Add a way to iterate through all PCI devices")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
We already have a function for probing all devices of a specific class,
use it.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
uclass_probe_all uses uclass_first_device/uclass_next_device assigning
the return value.
The interface for getting meaningful error is
uclass_first_device_check/uclass_next_device_check, use it.
Also do not stop iteration when an error is encountered. Probing all
devices includes those that happen to be after a failing device in the
uclass order.
Fixes: a59153dfeb ("dm: core: add function uclass_probe_all() to probe all devices")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
A recent change to regmap breaks building of phycore-rk3288 for me. The
difference is only a few bytes. Somehow CI seems to pass, even though it
fails when I run docker locally. But it prevents me from sending any more
pull requests.
In any case this board is clearly near the limit. We could revert the
offending change, but it is needed for sandbox tests.
Instead, add a way to drop the range checks in SPL, since they end up
doing nothing if everything is working as expected.
This makes phycore-rk3288 build again for me and reduces the size of SPL
slightly for a number of boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 947d4f132b ("regmap: fix range checks")
This function is already defined in spi.h but no implementation of it
currently exists in the tree. The implementation is based on the static
function spi_set_speed_mode(). The function prototype is modified so
that an success or error condition can be returned to the caller.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Fix typo that was caused by the same feature being split in to 2 different
configuration options. Replace CONFIG_USBNET_DEVADDR with
CONFIG_USBNET_DEV_ADDR
Signed-off-by: Ignacio Zamora <nachopitt@gmail.com>
MSM SMEM driver is currently missing <linux/sizes.h> header and throws
the following compile error:
drivers/smem/msm_smem.c: In function ‘qcom_smem_get_ptable’:
drivers/smem/msm_smem.c:635:71: error: ‘SZ_4K’ undeclared (first use in this function)
635 | ptable = smem->regions[0].virt_base + smem->regions[0].size - SZ_4K;
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: luka.perkov@sartura.hr
When the CCF is activated, the dev->parent is not necessary
the reference to SCMI transport and the function devm_scmi_of_get_channel
failed for the registered SCMI clock, child for protocol@14,
the channel is null and the SCMI clock driver crash for any operations.
This patch changes the first parameter of the ops of_get_channel(),
aligned with other process_msg() to pass directly the good reference,
i.e. parent result of find_scmi_transport_device(dev)
which return the reference of the scmi transport device.
Fixes: 8e96801aa6 ("firmware: scmi: add multi-channel support")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Provide a simple sandbox driver for the thermal uclass.
It simply registers and returns 100 degrees C if requested.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Simon Glass <sjg@chromium.org>
This buffer has the concatenated prefix and name written into it, so it
must be large enough to cover both strings plus the terminating NUL.
Fixes: 92c4a95ec7 ("pinctrl: Add new function pinctrl_generic_set_state_prefix()")
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix a copy-paste error I did when inserting the comment.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
When host issues "fastboot reboot fastboot", it's expected that the
board drops the USB connection before resetting.
On some boards, such as Khadas VIM3L and SEI610, this is not the case.
We observe the following error:
$ fastboot reboot fastboot
Rebooting into fastboot OKAY [ 0.004s]
fastboot: error: Failed to boot into userspace fastboot; one or more components might be unbootable.
This does not happen when we use the RST button on the board.
It can be reproduced in linux with:
# echo b > /proc/sysrq-trigger
In this case, we hit a undefined hardware behavior, where D+ and D-
are in an unknown state. Therefore the host can't detect usb
disconnection.
Make sure we always call usb_gadget_release() when a "fastboot reboot"
command is issued.
Note: usb_gadget_release() should be called before g_dnl_unregister()
because g_dnl_unregister() triggers a complete() call on each
endpoint (thus calling do_reset()).
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Remove unused ehci_{setup,shutdown}_phy() helpers now replaced by
generic_{setup,shutdown}_phy().
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Replace ehci_setup_phy() and ehci_shutdown_phy () by respectively
generic_setup_phy() and generic_shutdown_phy().
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Replace ohci_setup_phy() and ohci_shutdown_phy () by respectively
generic_setup_phy() and generic_shutdown_phy().
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
In drivers usb/host/{ehci,ohci}-generic.c, {ehci,ohci}_setup_phy() and
{ehci,ohci}_shutdown_phy() shares 95% of common code.
Factorize this code in new generic_{setup,shudown}_phy() functions.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Take the USB_ETHER ifdef block apart and make use of obj-$(VAR) instead
to include the source files in build. The duplicate CI_UDC entry is now
removed, the USB_DEVICE ifdef is now reduced to core.o ep.o addition,
the ether.o can be conditionally compiled in using USB_ETHER.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
- mtd: Update the function name to 'rfree'
- Support NAND ONFI EDO mode for imx8mn architecture
- dm: clk: add missing stub when CONFIG_CLK is deactivated
-----BEGIN PGP SIGNATURE-----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=VPkV
-----END PGP SIGNATURE-----
Merge tag 'u-boot-nand-20221009' of https://source.denx.de/u-boot/custodians/u-boot-nand-flash
- mtd: Update the function name to 'rfree'
- Support NAND ONFI EDO mode for imx8mn architecture
- dm: clk: add missing stub when CONFIG_CLK is deactivated
Instead of using DEBUG or LOG_DEBUG the driver still had its own
definition for debug output.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20221007122003.11239-11-ada@thorsis.com
Instead of using DEBUG or LOG_DEBUG the driver still had its own
definition for debug output.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20221007122003.11239-10-ada@thorsis.com
Instead of using DEBUG or LOG_DEBUG the driver still had its own
definition for debug output.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20221007122003.11239-9-ada@thorsis.com
Instead of using DEBUG or LOG_DEBUG the driver still had its own
definition for debug output.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20221007122003.11239-8-ada@thorsis.com
Instead of using DEBUG or LOG_DEBUG the driver still had its own
definition for debug output.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20221007122003.11239-7-ada@thorsis.com
Instead of using DEBUG or LOG_DEBUG the driver still had its own
definition for debug output.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20221007122003.11239-6-ada@thorsis.com
Warning appears if built with FPGA_DEBUG defined:
CC drivers/fpga/virtex2.o
/mnt/data/adahl/src/u-boot/drivers/fpga/virtex2.c: In function ‘virtex2_ssm_load’:
/mnt/data/adahl/src/u-boot/drivers/fpga/virtex2.c:333:11: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ {aka ‘long unsigned int’} [-Wformat=]
PRINTF("%s:%d:done went active early, bytecount = %d\n",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
__func__, __LINE__, bytecount);
~~~~~~~~~
/mnt/data/adahl/src/u-boot/drivers/fpga/virtex2.c:25:37: note: in definition of macro ‘PRINTF’
#define PRINTF(fmt, args...) printf(fmt, ##args)
^~~
/mnt/data/adahl/src/u-boot/drivers/fpga/virtex2.c: In function ‘virtex2_ss_load’:
/mnt/data/adahl/src/u-boot/drivers/fpga/virtex2.c:468:12: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ {aka ‘long unsigned int’} [-Wformat=]
PRINTF("%s:%d:done went active early, bytecount = %d\n",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
__func__, __LINE__, bytecount);
~~~~~~~~~
/mnt/data/adahl/src/u-boot/drivers/fpga/virtex2.c:25:37: note: in definition of macro ‘PRINTF’
#define PRINTF(fmt, args...) printf(fmt, ##args)
^~~
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20221007122003.11239-5-ada@thorsis.com
The additional comma messes up the arguments.
Warning appears if built with FPGA_DEBUG defined:
CC drivers/fpga/spartan3.o
/mnt/data/adahl/src/u-boot/drivers/fpga/spartan3.c: In function ‘spartan3_sp_load’:
/mnt/data/adahl/src/u-boot/drivers/fpga/spartan3.c:118:11: warning: too many arguments for format [-Wformat-extra-args]
PRINTF ("%s: Function Table:\n"
^~~~~~~~~~~~~~~~~~~~~~~
/mnt/data/adahl/src/u-boot/drivers/fpga/spartan3.c:18:37: note: in definition of macro ‘PRINTF’
#define PRINTF(fmt,args...) printf (fmt ,##args)
^~~
Fixes: 875c78934e ("Add Xilinx Spartan3 family FPGA support Patch by Kurt Stremerch, 14 February 2005")
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20221007122003.11239-4-ada@thorsis.com
That extra comma messes up format arguments.
Warning appears if built with FPGA_DEBUG defined:
CC drivers/fpga/spartan2.o
/mnt/data/adahl/src/u-boot/drivers/fpga/spartan2.c: In function ‘spartan2_sp_load’:
/mnt/data/adahl/src/u-boot/drivers/fpga/spartan2.c:112:11: warning: too many arguments for format [-Wformat-extra-args]
PRINTF ("%s: Function Table:\n"
^~~~~~~~~~~~~~~~~~~~~~~
/mnt/data/adahl/src/u-boot/drivers/fpga/spartan2.c:12:37: note: in definition of macro ‘PRINTF’
#define PRINTF(fmt,args...) printf (fmt ,##args)
^~~
CC drivers/fpga/spartan3.o
/mnt/data/adahl/src/u-boot/drivers/fpga/spartan3.c: In function ‘spartan3_sp_load’:
/mnt/data/adahl/src/u-boot/drivers/fpga/spartan3.c:117:11: warning: too many arguments for format [-Wformat-extra-args]
PRINTF ("%s: Function Table:\n"
^~~~~~~~~~~~~~~~~~~~~~~
/mnt/data/adahl/src/u-boot/drivers/fpga/spartan3.c:17:37: note: in definition of macro ‘PRINTF’
#define PRINTF(fmt,args...) printf (fmt ,##args)
^~~
Fixes: e221174377 ("Initial revision")
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20221007122003.11239-3-ada@thorsis.com
Fix the following sparse and compile time warning
triggered with W=1:
drivers/clk/clk_versal.c:605:5:
warning: no previous prototype for 'versal_clock_setup'
[-Wmissing-prototypes]
605 | int versal_clock_setup(void)
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20221007105535.31902-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Fix the following sparse and compile time warning triggered with W=1:
drivers/soc/soc_xilinx_zynqmp.c:288:5:
warning: no previous prototype for 'soc_xilinx_zynqmp_get_machine'
[-Wmissing-prototypes]
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20221004055201.26146-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support for imx8mn architecture in order to run the NAND
in fast edo mode.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Rename the gpmi_apb_bch clock name to gpmi_bch_apb, as you can find in
the device tree.
Fixes: commit a59691280d ("MXS_NAND: Add clock support for iMX8")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
This clock name is not present in any U-boot and Linux kernel device
tree.
Fixes: commit a59691280d ("MXS_NAND: Add clock support for iMX8")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Add gpmi nand clock. Those clock can be used in mxs nand driver
to run nand to EDO mode 5, 4, ...
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Add shared counter in order to avoid to swich off clock that
are already used.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
This fixes the below build error if nand.c is included in
an SPL build.
/work/u-boot/drivers/mtd/nand/raw/nand.c: In function ‘nand_init_chip’:
/work/u-boot/drivers/mtd/nand/raw/nand.c:82:28: error: ‘nand_chip’ undeclared (first use in this function)
82 | struct nand_chip *nand = &nand_chip[i];
| ^~~~~~~~~
/work/u-boot/drivers/mtd/nand/raw/nand.c:82:28: note: each undeclared identifier is reported only once for each function it appears in
/work/u-boot/drivers/mtd/nand/raw/nand.c:84:20: error: ‘base_address’ undeclared (first use in this function); did you mean ‘base_addr’?
84 | ulong base_addr = base_address[i];
| ^~~~~~~~~~~~
| base_addr
Fixes: 068c41f1cc ("Finish conversion CONFIG_SYS_NAND_SELF_INIT to Kconfig")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Fix the following sparse and compile time warning triggered with W=1:
drivers/spi/zynqmp_gqspi.c:286:6:
warning: no previous prototype for 'zynqmp_qspi_set_tapdelay'
[-Wmissing-prototypes]
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20221004053730.25602-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
For the TI SoCs affected by errata i2329, enable MDIO manual
mode by default
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
In certain TI SoCs, on the CPSW and ICSS peripherals, there is
a possibility that the MDIO interface returns corrupt data on
MDIO reads or writes incorrect data on MDIO writes. There is also
a possibility for the MDIO interface to become unavailable until
the next peripheral reset.
The workaround is to configure the MDIO in manual mode and disable the
MDIO state machine and emulate the MDIO protocol by reading and writing
appropriate fields in MDIO_MANUAL_IF_REG register of the MDIO controller
to manipulate the MDIO clock and data pins.
More details about the errata i2329 and the workaround is available in:
https://www.ti.com/lit/er/sprz487a/sprz487a.pdf
Add implementation to disable MDIO state machine, configure MDIO in manual
mode and provide software MDIO read and writes via MDIO bitbanging. Allow
the MDIO to be initialized based on the need for manual mode.
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Include linux/sizes.h because it defines SZ_64K which is used in many
places inside k3-udma.c
This fixes the error: ‘SZ_64K’ undeclared which appears during build
time
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On the 32bit ARM sandbox 'dm ut dm_test_devm_regmap' fails with an abort.
This is due to incorrect range checks.
On 32-bit systems the size of size_t and int is both 32 bit. The expression
(offset + val_len) is bound to overflow if offset == -1. Add an overflow
check.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move the code making sure that the timer is initialized only once into
orion_timer_init(), which is called from timer_early_init() and from
orion_timer_probe(). This way the timer is not re-initialized.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Michael Walle <michael@walle.cc>
Cc: Pali Rohár <pali@kernel.org>
Replace the if/else chain in pxa_ecc_init() with a lookup table. This
makes the code more concise and hopefully easier to follow. Remove the
unused ecc_layout tables and replace it with a single dummy one (the
pxa3xx driver has never used this but the mtd subsystem expects it to be
provided).
Tested on an Allied Telesis x530 switch with Micron MT29F2G08ABAEAWP
NAND Flash.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Firmware calls need node_id which is basically "power-domains" id.
At present static values are used based on the "device_id" property of
dt.
Instead of this, read "power-domains" id from dt and use it. Add a
element called node_id in priv structure and read it from dt. Replace
static node_id with this priv->node_id across the driver.
Since "device_id" is not used anywhere else simply remove it.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20220930092548.18453-3-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
In Versal platform power domain node_id is bigger than u8, hence
change prototype to u32 to accommodate. Change u8 to u32 in the function
prototypes that use node_id and remove casting to u32 from
xilinx_pm_request() call parameters.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20220930092548.18453-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Here are the smatch warning messages:
drivers/net/xilinx_axi_emac.c:324 axiemac_phy_init()
error: 'phydev' dereferencing possible ERR_PTR()
drivers/net/zynq_gem.c:340 zynq_phy_init()
error: 'priv->phydev' dereferencing possible ERR_PTR()
Fix by adding error checking before dereferencing the pointer.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20220929045605.23964-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The maximum length is capped similarly to the emaclite_send function.
Avoid integer underflow for values of ip->ip_len < 30, the minimum
length of an IP packet is 21 bytes.
Signed-off-by: Samuel Obuch <samuel.obuch@codasip.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Link: https://lore.kernel.org/r/20220927112103.155689-3-samuel.obuch@codasip.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Use __raw_read* and __raw_write* functions to ensure read/write
is passed to the memory-mapped regions, as non-volatile accesses
may get optimised out.
Signed-off-by: Samuel Obuch <samuel.obuch@codasip.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Link: https://lore.kernel.org/r/20220927112103.155689-2-samuel.obuch@codasip.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Function ioremap_nocache seems to be defined only for MIPS and Microblaze
architectures. Therefore, the function call in the emaclite driver causes
this driver to be unusable with other architectures, for example RISC-V.
Use ioremap function instead of ioremap_nocache, and include linux/io.h
instead of asm/io.h, so that ioremap function is automatically created,
if not defined by the architecture. We can switch to the ioremap function,
as Microblaze's ioremap_nocache is just empty and in MIPS implementations
of ioremap_nocache and ioremap are the same.
Signed-off-by: Samuel Obuch <samuel.obuch@codasip.com>
Link: https://lore.kernel.org/r/20220927112103.155689-1-samuel.obuch@codasip.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
To check dynamic loading of config object, currently APU_0 is used.
Suggestion from pmwfw team is to load OCM_BANK_0 and check for
XST_PM_NO_ACCESS error only to skip future config objects. Other errors
should not be considered for skipping. Change from NODE_APU_0 to
NODE_OCM_BANK_0 and check for XST_PM_NO_ACCESS to skip future config
objects.
Add ": " to printf statement when there is no permission to load config
object, to align with PMUFW version print.
Update kernel doc for return value for zynqmp_pmufw_load_config_object().
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/2784018844ba4afced0e3edff76bdbfe532f517d.1664523444.git.michal.simek@amd.com
For future DM based FPGA drivers and for now to have a meaningful
logging class for old FPGA drivers.
Suggested-by: Michal Simek <michal.simek@amd.com>
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Dahl <post@lespocky.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20220930120430.42307-2-post@lespocky.de
Signed-off-by: Michal Simek <michal.simek@amd.com>
At present ofnode_write_prop() is inconsistent between livetree and
flattree, in that livetree requires the caller to ensure the property
value is stable (e.g. in rodata or allocated) but flattree does not, since
it makes a copy.
This makes the API call a bit painful to use, since the caller must do
different things depending on OF_LIVE.
Add a new 'copy' argument which tells the function to make a copy if
needed. Add some tests to cover this behaviour.
Signed-off-by: Simon Glass <sjg@chromium.org>
We need to be able to look up phandles in any FDT, not just the control
FDT. Use the 'other' FDT to test this, with a helper function which gets
this as an oftree that can then we used as needed.
Add a few more tests and some comments at the top of the file, to explain
what is going on.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add the logic to redirect requests for the device tree through a function
which can look up the tree ID. This works by using the top bits of
ofnode.of_offset to encode a tree.
It is assumed that there will only be a few device trees used at runtime,
typically the control FDT (always tree ID 0) and possibly a separate FDT
to be passed the OS.
The maximum number of device trees supported at runtime is 8, with this
implementation. That would use bits 30:28 of the node-offset value,
meaning that the positive offset range is limited to bits 27:0, versus
30:1 with this feature disabled. That still allows a device tree of up
to 256MB, which should be enough for most FITs. Larger ones can be
supported by using external data with the FIT, or by enabling OF_LIVE.
Update the documentation a little and fix up the comment for
ofnode_valid().
Signed-off-by: Simon Glass <sjg@chromium.org>
At present, unless OF_LIVE is enabled, ofnode only supports access to one
device tree, the control FDT. This is because only the node offset is
encoded in ofnode, with the tree being implicit.
This makes ofnode (without OF_LIVE) unsuitable for device tree fixups, as
implemented by ft_board_setup() and other such functions.
To solve this, we can use the top bits of the node offset to hold a tree
ID.
Add the definitions for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function turns out to be a little confusing since it looks up a path
and also registers the tree. Split it into two, one that gets the root
node and one that looks up a path, so the purpose is clear.
Registering the tree will happen in a function to be added in a later
patch, called oftree_from_fdt().
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases we want to obtain an ofnode in the same tree as a different
ofnode, such as when looking up a subnode. At present this is trivial,
since there is only one tree. When there are multiple trees, this
implementation will change.
Also move the ofnode_to_offset() function up higher in the header file,
since we will need to provide a different implementation with multiple
trees.
Signed-off-by: Simon Glass <sjg@chromium.org>
When we have multiple trees, the ofnode logic needs to be told which one
to use. Create a new function which takes an oftree argument, along with
a helper to obtain the FDT pointer from an oftree.
Signed-off-by: Simon Glass <sjg@chromium.org>
The flat device tree is assumed to be the control FDT but this is not
always the case. Update the ofnode implementation to obtain the node via
an function call so we can eventually add support for selecting different
trees.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current tests do not cover all the behaviour. Add some more.
Tidy up a few inconsistencies between livetree and flattree which come to
light with these tests. Also drop the -ENODATA error since it is never
actually returned.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current implementation creates a 'name' value for every node. This
is not needed for the latest device tree format, which includes a name in
the node header.
Adjust the code to point the name at the node header instead.
Also simplify ofnode_get_name(), now that we can rely on it to set the
name correctly. Update the comment to make it clear what name the root
node has.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current name is quite unwieldy. Change it to use an ofprop_ prefix
and shorten it. Fix the return-value comment while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update the function to mark it with the const attribute. Also avoid
calling it multiple times in the devfdt_get_addr_index() function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that we support writing to ofnodes, the const is not accurate. Drop
it to avoid undesirable casting.
Also drop the ofnode_to_npw() which is now the same as ofnode_to_np().
Signed-off-by: Simon Glass <sjg@chromium.org>
Add this feature to the ofnode interface, supporting both livetree and
flattree. If the node exists it is returned, along with a -EEXIST error.
Update the functions it calls to handle this too.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function currently assumes that the control FDT is used. Update it
to allow a root node to be passed, so it can work with any tree.
Also add a comment to ofnode_get_by_phandle() so that its purpose is
clear.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the log functions instead of pr_...() so we can avoid using __func__.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This is not needed and we should avoid typedefs. Use the struct instead
and rename it to indicate that it really is a legacy struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
The udelay() function in lib/time.c contains a WATCHDOG_RESET()
call. So use __udelay() in max6370_wdt.c to prevent recursion.
Fixes: 0a095fc53b ("watchdog: Add MAX6370 watchdog timer driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The udelay() function in lib/time.c contains a WATCHDOG_RESET()
call. The only reason this doesn't lead to a catastrophic infinite
recursion is due to the rate-limiting in wdt-uclass.c:
if (time_after_eq(now, priv->next_reset)) {
priv->next_reset = now + priv->reset_period;
wdt_reset(dev);
}
But this would fall apart if ->next_reset was updated after calling the
device's reset method.
This is needlessly fragile, and it's easy enough to avoid that
recursion in the first place by just using __udelay() directly.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Stefan Roese <sr@denx.de>
xilinx:
- Add support for new Versal NET SOC
zynqmp:
- Use mdio bus for ethernet phy description
- Wire ethernet phy reset via i2c-gpio
versal:
- Config cleanup
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYzGwogAKCRDKSWXLKUoM
Ial4AJ9+4WHn0MV2X7gK1fyh4lUW7ggPhQCggsYlSoACgMgdji17SAPhCv/W3IA=
=BmA9
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2023.01-rc1-v2' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2023.01-rc1 (round 2)
xilinx:
- Add support for new Versal NET SOC
zynqmp:
- Use mdio bus for ethernet phy description
- Wire ethernet phy reset via i2c-gpio
versal:
- Config cleanup
Currently all GPIOs supported by CMD_EXT_CONTROL/CMD_GET_EXT_CONTROL_STATUS
commands (last 16 GPIOs) are available only when FEAT_PERIPH_MCU feature
bit is set. So do not register these GPIOs by U-Boot driver when this
feature bit is not set, so U-Boot 'gpio' command would see only GPIOs which
really exists.
Fixes: 5e4d24ccc1 ("gpio: Add Turris Omnia MCU driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
When processing USB_REQ_CLEAR_FEATURE, USB_REQ_SET_FEATURE, and
USB_REQ_GET_STATUS packets in dwc2_ep0_setup an out of bounds access
can occur. This is caused by the wIndex field of the usb control packet
being used as an index into an array whose size is DWC2_MAX_ENDPOINTS (4).
Signed-off-by: Alison Huffman <alisn@google.com>
At present sandbox is producing a warning about SCSI migration. Drop the
legacy code and replace it with a new implementation.
Also drop the SATA command, which does not work with driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this code out of the helper function so we can (later) add it as part
of the shared emulation code. Set a default value of 0 for buff_used since
that is what we use when there is an error.
Signed-off-by: Simon Glass <sjg@chromium.org>
In preparation for sharing the emulation code between two drivers, move
some of the fields into a new struct. Use a separate header file so it
can be used by various drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
This has the same name as a field in our local private struct, which is
confusing. Change the name to xfer_len instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Changing baudrate is a sensitive operation. To ensure that U-Boot messages
printed before changing baudrate are not lost, call new U-Boot console
flush() function.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Like in all other console functions, implement also serial_flush() function
as a fallback int console flush() function.
Flush support is available only when config option CONSOLE_FLUSH_SUPPORT is
enabled. So when it is disabled then provides just empty static inline
function serial_flush().
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
UART drivers have putc/puts functions which just put characters into HW
transmit queue and do not wait until all data are transmitted.
Implement flush callback via serial driver's pending(false) callback which
waits until HW transmit all characters from the queue.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
During init_dram() is called also compute_lowest_common_dimm_parameters()
function which prints multi-line detailed output. So print also re-aligning
filler after "Detected ?DIMM" line to have "DRAM: " output aligned.
Signed-off-by: Pali Rohár <pali@kernel.org>
U-Boot core code already handles the case when RAM size is bigger than
CONFIG_MAX_MEM_MAPPED. So there is no need to do duplicate check in fsl ddr
driver for CONFIG_MAX_MEM_MAPPED. Instead simplify code to just check if
RAM size can be representable in phys_size_t type. And avoid printing
warning if phys_size_t is just 1 byte smaller than RAM size, which is the
typical situation with 4 GB DDR module.
Signed-off-by: Pali Rohár <pali@kernel.org>
Function fsl_ddr_compute() always return size in unsigned long long type,
but function fsl_ddr_sdram_size() returns size in phys_size_t type.
When 36-bit addressing mode is not enabled then phys_size_t type is only
32-bit and thus it cannot store value 4GB (0x100000000). Function
fsl_ddr_sdram_size() in this case returns truncated value 0x0.
Fix this issue by returning the highest representable value, which is
0xffffffff (4GB - 1 byte).
This change fixes crashing of proper U-Boot because it detected 4 GB module
as RAM with zero size.
Signed-off-by: Pali Rohár <pali@kernel.org>
Check needs to be done against CONFIG_MAX_MEM_MAPPED macro and not fixed
size 4GB (as CONFIG_MAX_MEM_MAPPED can be lower and for example for e500
cores it is just 2GB). Also fix printf re-align, which should be applied
only for non-SPL builds, during init_dram() call.
Signed-off-by: Pali Rohár <pali@kernel.org>
