Make the SoCFPGA MMC stub pick clock via the clock manager
frequency accessors instead of hard-coding the frequency.
Also fix calloc() misuse.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
The dw_mmc driver was responding to errors with debug(). Change that
to prinf()/puts() respectively so that any errors are immediately
obvious. Also adjust english in comments.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Chin Liang See <clsee@altera.com>
dw_mmc driver was responding to errors with debug(). Change that to
prinf so that any errors are immediately obvious. Also adjust english
in comments.
Signed-off-by: Pavel Machek <pavel@denx.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
After setting the bus width, the extended CSD register is read. Some selected
fields are compared with previously read extended CSD register fields. In this
comparison the EXT_CSD_ERASE_GROUP_DEF field is compared. But this field is
previously written under certain circumstances. And then the comparison fails.
Only compare read-only fields. Therefore compare field EXT_CSD_HC_WP_GRP_SIZE
instead of field EXT_CSD_ERASE_GROUP_DEF.
Signed-off-by: Mario Schuknecht <mario.schuknecht@dresearch-fe.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
In function mvebu_mmc_write notice command timeout. It is possible that a
command is done, but a timeout occurred.
Enable timeout in set bus function.
Set window registers. Without that I could not use the driver on a Kirkwood
88F6282 SoC.
Set high capacity and 52MHz driver feature.
Signed-off-by: Mario Schuknecht <mario.schuknecht@dresearch-fe.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The capacity and lba for an MMC device with part_num 0 reflects the
whole device. When mmc_switch_part() successfully switches to a
partition, the capacity is changed to that partition. As partition 0
does not physically exist, attempts to switch back to the whole device
will indicate an error, but the capacity setting for the whole device
must still be restored to match the partition.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Tested-by: Tom Rini <trini@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
if we set manually this bit on the eMMC card using mmc_switch(...),
we also have to set it within our (before read) internal structure
'ext_csd'.
Otherwise following checks on this will fail.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Wait data transfer till the data end bit other than the data block end
bit is set.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
This would be useful to start moving various config options.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
For LS1, esdhc is big-endian IP. Accessing the registers
should be in big-endian mode. So we use esdhc_read32()
to read Host controller capabilities register for LS1.
For LS1, when using CMD12, cmdtype need to be set to
ABORT, otherwise, next read command will hang.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Structure defining clock manager hardware was wrong, leading to
wrong registers being accessed and hang in MMC init.
This fixes structure to match hardware.
Signed-off-by: Pavel Machek <pavel@denx.de>
If the MCI IP version >= 0x300, it supports hight speed mode
option, this patch enable it.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The mode register is different between MCI IP version.
So, according to MCI IP version to set the mode register.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
To fix the clock divider calculation error when the controller
clock same as the operating frequency. This is known as bypass
mode. In this mode, the divider should be 0.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Implement SD driver for the S3C24xx family. This implementation
is currently only capable of using the PIO transfers, DMA is not
supported.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Seems like the controller doesn't support the flag. None of the hi-speed cards
I've tried could be read, while they successfully worked with the quirk enabled.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
This patch add Marvell kirkwood MVSDIO/MMC driver
and enable it for Sheevaplugs and OpenRD boards.
Signed-off-by: Gerald Kerma <drEagle@doukki.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Add missing prototypes for global functions and
make local functions static.
cc: panto@antoniou-consulting.com
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
The DMA code in sunxi_mmc.c is broken. mmc_trans_data_by_dma() allocates the
dma descriptors on the stack, and then exits while the dma transfer is in
progress, so the dma engine is reading stack memory which at that point may
be re-used. So far we've gotten away with this by luck, but recent u-boot
changes have shifted the stack start address by 16 bytes, which combined
with dma alignment now exposes this problem.
Since we end up just busy waiting for the dma engine anyway, this commit
fixes things by simply removing the dma code, resulting in smaller bug-free
code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
commit 18b06652cd "tools: include u-boot version of sha256.h"
unconditionally forced the sha256.h from u-boot to be used
for tools instead of the host version. This is fragile though
as it will also include the host version. Therefore move it
to include/u-boot to join u-boot/md5.h etc which were renamed
for the same reason.
cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Cleanup to balance malloc/free calls.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Rather than just returning -1 everywhere, try to return something
meaningful from mmc_select_hwpart(). Note that most other MMC functions
don't do this, including functions called from mmc_select_hwpart(), so
I'm not sure how effective this will be. Still, it's one less place with
hard-coded -1.
Suggested-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
On Mon, 2014-05-05 at 14:18 +0200, Stefan Roese wrote:
> > + case 1:
> > +#if CONFIG_MMC1_PG
> Are you sure that this is correct and shouldn't be:
>
> +#ifdef CONFIG_MMC1_PG
>
> ?
It's "correct" in so far as it works (the boards.cfg config stuff
#defines things to 1), but I think you are right that it isn't the
preferred style. But...
> A quick scan through this patch series shows that this define
> is not set at all. Perhaps its outdated? Or is it used to support
> some other sunxi SoC? Not sure, perhaps it should be removed for
> now.
...I had thought that it was to support some other board which wasn't
being upstreamed right now, so eventually useful and harmless for now,
but I've just checked and it isn't actually used by any of the boards in
u-boot-sunxi.git. So rather than fix it to use #ifdef lets drop it.
Rather than resend the entire series, here is v5.1 of this patch.
> Other than this please add my:
>
> Reviewed-by: Stefan Roese <sr@denx.de>
Thanks!
8<---------------------------------
>From 20704e35a41664de5f516ed0e02981ac06085102 Mon Sep 17 00:00:00 2001
From: Ian Campbell <ijc@hellion.org.uk>
Date: Fri, 7 Mar 2014 04:29:39 +0000
Subject: [PATCH v5.1 7/8] sunxi: mmc support
This adds support for the MMC controller on the Allwinner A20 (sun7i)
processor.
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Luke Leighton <lkcl@lkcl.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Wills Wang <wills.wang.open@gmail.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Cc: Aaron Maoye <leafy.myeh@allwinnertech.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: Tom Rini <trini@ti.com>
In 7168977 we made calls to check_and_invalidate_dcache_range()
conditional on !CONFIG_SYS_FSL_ESDHC_USE_PIO. Only define this function
in this case as well.
Signed-off-by: Tom Rini <trini@ti.com>
This enables specifying which eMMC HW partition to target for any U-Boot
command that uses the generic get_partition() function to parse its
command-line arguments.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch adds functions for read, write and authentication
key programming for the Replay Protected Memory Block partition
in the eMMC.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
MMC switch command for unsupported feature (e.g. bus width) sets a switch
error bit in card status. This bit should be checked, and, if it's set,
no access with new controller settings should be performed.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
When configure the fsl_esdhc driver to PIO mode by defining
"CONFIG_SYS_FSL_ESDHC_USE_PIO", the SD/MMC read and write will fail.
Two bugs in the driver to cause the issue:
1. The read buffer was invalidated after reading from DATAPORT register,
which should be only applied to DMA mode. The valid data in cache was
overwritten by physical memory.
2. The watermarks are not set in PIO mode, will cause according state not
be set.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Conflicts:
boards.cfg
Conflicts were trivial once u-boot-arm/master boards.cfg was
reformatted (commit 6130c146) to match u-boot/master's own
reformatting (commit 1b37fa83).
To reuse the code, added the s5p_sdhci_core_init function.
Before applied this patch, didn't use the 8-bit mode at exynos baord.
Because it didn't set "MMC_MODE_8BIT".
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Restore the platdata(property of dt) into host struct.
Then data's information is maintained and reused anywhere.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
If CONFIG_API is ever to be enabled on Tegra, this define must be set,
since api/api_storage.c uses it.
A couple of annoyting things about CONFIG_SYS_MMC_MAX_DEVICE
1) It isn't documented in README. The same is true for a lot of similar
defines used by api_storage.c.
2) It doesn't represent MAX_DEVICE but rather NUM_DEVICES, since the
valid values are 0..n-1 not 0..n.
However, I this patch does not address those shortcomings.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
T4240RDB board Specification
----------------------------
Memory subsystem:
6GB DDR3
128MB NOR flash
2GB NAND flash
Ethernet:
Eight 1G SGMII ports
Four 10Gbps SFP+ ports
PCIe:
Two PCIe slots
USB:
Two USB2.0 Type A ports
SDHC:
One SD-card port
SATA:
One SATA port
UART:
Dual RJ45 ports
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: fix CONFIG_SYS_QE_FMAN_FW_ADDR in T4240RDB.h]
Add support of loading image, binary for MMC and SPI during SPL boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Fix following compile warnings
fsl_esdhc_spl.c: In function 'mmc_boot':
fsl_esdhc_spl.c:35:10: warning: unused variable 'byte_num' [-Wunused-variable]
fsl_esdhc_spl.c:35:7: warning: unused variable 'i' [-Wunused-variable]
fsl_esdhc_spl.c:34:8: warning: unused variable 'val' [-Wunused-variable]
fsl_esdhc_spl.c:33:6: warning: unused variable 'blklen' [-Wunused-variable]
fsl_esdhc_spl.c:105:7: warning: 'tmp_buf' may be used uninitialized in this
function [-Wuninitialized]
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1. The Data timeout counter value in eSDHC_SYSCTL register is
not working as it should be, so add quirks to enable this
workaround to fix it to the max value 0xE.
2. Add CONFIG_SYS_FSL_ERRATUM_ESDHC111 to enable its workaround.
* Update of patch for change mmc interface by
Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The controller reset is performed now if command error occurs.
This commit adds the reset for the case of data related errors too.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Calculation of the timeout value should be based on actual clock value,
written to controller registers. Since mmc->tran_speed is either the
maximum allowed speed, or the preliminary value, that is be not yet
set to registers, the actual timeout, taken by the controller, based
on its clock settings, may be much longer than expected, based on
mmc->tran_speed value. In particular it happens at early initialization
stage, when typical value of mmc->tran_speed is 20MHz or 26MHz, while
actual clock setting, configured in the controller, is 400kHz.
It's more correct to use mmc->clock value for timeout calculation instead.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Some eMMC chips may need the RST_n_FUNCTION bit set to a non-zero value
in order for warm reset of the system to work. Details on this being
required will be part of the eMMC datasheet. Also add using this
command to the dra7xx README.
* Whitespace fix by panto
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
In the recent mmc cleanup, the mmc_host_is_spi macro was broken and
bfin_sdh.c had mmc->bus_width turned into mmc_bus_width(mmc), both of
which were incorrect.
Signed-off-by: Tom Rini <trini@ti.com>
The way that struct mmc was implemented was a bit of a mess;
configuration and internal state all jumbled up in a single structure.
On top of that the way initialization is done with mmc_register leads
to a lot of duplicated code in drivers.
Typically the initialization got something like this in every driver.
struct mmc *mmc = malloc(sizeof(struct mmc));
memset(mmc, 0, sizeof(struct mmc);
/* fill in fields of mmc struct */
/* store private data pointer */
mmc_register(mmc);
By using the new mmc_create call one just passes an mmc config struct
and an optional private data pointer like this:
struct mmc = mmc_create(&cfg, priv);
All in tree drivers have been updated to the new form, and expect
mmc_register to go away before long.
Changes since v1:
* Use calloc instead of manually calling memset.
* Mark mmc_register as deprecated.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Using an array is pointless; even more pointless (and scary) is using
sprintf to fill it without a format string.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Remove the in-structure ops and put them in mmc_ops with
a constant pointer to it.
This makes the mmc structure smaller as well as conserving
code space (in theory).
All in-tree drivers are converted as well; this is done in a
single patch in order to not break git bisect.
Changes since V1:
Fix compilation b0rked issue on omap platforms where OMAP_GPIO was
not set.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
This patch enables support for device tree for sdhci driver.
Non DT case is still supported.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add support for the Kona SDHCI found on Broadcom mobile SoCs.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>
With d6a320d we moved some clock externs out of blackfin_local.h and
into clock.h but now need to include <asm/clock.h> in more drivers to
avoid warnings.
Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Tom Rini <trini@ti.com>
The open and close mmc sub-commands implement a hard-coded set of values
specific to the SMDK5250 platform. Remove these commands as what they
did can be done instead with a series of mmc dev / bootpart / bootbus
commands instead now.
Cc: Amar <amarendra.xt@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Add a bootbus sub-command to the mmc command to allow for setting
the boot_bus_width, reset_boot_bus_width and boot_mode fields of
BOOT_BUS_WIDTH (EXT_CSD[177]).
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Add a partconf sub-command to the mmc command to allow for setting
the boot_ack, boot_partition and partition_access fields of
PARTITION_CONFIG (formerly BOOT_CONFIG, EXT_CSD[179]). Part of this
requires changing the check for 'part' from an strncmp to a strcmp, like
the rest of the sub-commands.
Cc: Andy Fleming <afleming@gmail.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
As per the below commit
"mmc: sdhci: add the quirk for broken r1b response"
(sha1: 3a6383207b)
need to add quirk SDHCI_QUIRK_BROKEN_R1B, when the
response type is R1b.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
This patch corrects the divider value written to CLKDIV register.
Since SDCLKIN is divided inside controller by the DIVRATIO value set
in the CLKSEL register, we need to use the same output clock value to
calculate the CLKDIV value.
as per user manual: cclk_in = SDCLKIN / (DIVRATIO + 1)
Input parameter to mmc_clk is changed to dwmci_host, since
we need the same to read DWMCI_CLKSEL register.
This improves the read timing values for channel 0 on SMDK5250
from 0.288sec to 0.144sec
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
U-Boot currently sets MMC cards' RCA register to 0. This value is
reserved according to the specification. Use a value of 1 instead, just
like the Linux kernel.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Tegra124's MMC controller is very similar to earlier SoC generations,
and can be supported by the same driver.
However, there are some non-backwards-compatible HW differences, and
hence a new DT compatible value must be used to describe the HW. This
patch updates the driver to support that new compatible value.
That said, the HW differences are only relevant when enabling certain
high-performance transfer modes. Since the driver is currently very
simple and doesn't enable those modes, we don't actually need to address
any of these HW differences in the code yet, hence the simple nature of
this patch.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The upper 4 data signals of esdhc are shared with spi flash.
So detect if the upper 4 pins are assigned to esdhc before
enable sdhc 8 bit width.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Card detection pin is ineffective on T4240QDS Rev1.0.
There are two cards can be connected to board.
1. eMMC card is built-in board, can not be removed. so
For eMMC card it is always there.
2. Card detecting pin is functional for SDHC card in Rev2.0.
This workaround force sdhc driver scan and initialize the card
regardless of whether the card is inserted or not in case Rev1.0.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
To add the DesignWare MMC driver support for Altera SOCFPGA. It
required information such as clocks and bus width from platform
specific files (SOCFPGA handoff files)
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The eMMC and the SD-Card specifications describe the optional SET_DSR command.
During measurements at our lab we found that some cards implementing this feature
having really strong driver strengts per default. This can lead to voltage peaks
above the specification of the host on signal edges for data sent from a card to
the host.
Since availability of a given card type may be shorter than the time a certain
hardware will be produced it is useful to have support for this command (Alternative
would be changing termination resistors and adapting the driver strength of the
host to the used card.)
Following proposal for an implementation:
- new field that reflects CSD field DSR_IMP in struct mmc
- new field for design specific DSR value in struct mmc
- board code can set DSR value in mmc struct just after registering an controller
- mmc_startup sends the the stored DSR value before selecting a card, if DSR_IMP is set
Additionally the mmc command is extended to make is possible to play around with different
DSR values.
The concept was tested on a i.MX53 based platform using a Micron eMMC card where the default
DSR is 0x0400 (12mA) but in our design 0x0100 (0x0100) were enough. To use this feature for
instance on a mx53loco one have to add a call to mmc_set_dsr() in board_mmc_init() after
calling fsl_esdhc_initialize() for the eMMC.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Fixup prints to show where the print is done from, and
a few minor formatting/grammar issues.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Bounce buffer implementation takes care of proper data buffer alignemt
and correct flush/invalidation of data cache at once so we no longer
depend on input data variety and make sure CPU and MMC controller deal
with expected data in case of enabled data cache.
Bounce buffer requires to add its definition (CONFIG_BOUNCE_BUFFER) in
board configuration, otherwise corresponding library won't be compiled
and linker will fail to build resulting executable.
Difference since v1 - fixed compile-time warning with type casting to
"void *":
Slight edit to remove UTF8 characters in the commit message.
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
====
passing argument 2 of 'bounce_buffer_start' discards 'const' qualifier
from pointer target type
====
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Amar <amarendra.xt@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Andy Fleming <afleming@gmail.com>
To enhance the SDMMC DesignWare driver to use calloc instead of
malloc. This will avoid the incident that uninitialized members
of mmc structure are later used for NULL comparison.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Faraday FTSDC021 is a controller which is compliant with
SDHCI v3.0, SDIO v2.0 and MMC v4.3.
However this driver is only verified with SD memory cards.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
CC: Andy Fleming <afleming@gmail.com>
Existing eSDHC SPL framework assumes booting from sd-image
with boot_format header which contains final u-boot Image
offset and size. No such header is present in case of
corenet devices like T1040 as corenet deivces use PBI-RCW
based intialization.
So, for corenet deives, SPL bootloader use values provided
at compilation time. These values can be defined in board
specific config file.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
If platform provides "host->fifoth_val" it will be used for
initialization of DWMCI_FIFOTH register. Otherwise default value will be
used.
This implementation allows:
* escape unclear and recursive calculations that are currently in use
* use whatever custom value for DWMCI_FIFOTH initialization if any
particular SoC requires it
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Amar <amarendra.xt@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Andy Fleming <afleming@freescale.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
dw-mmc.c is the general driver file.
So, remove the exynos specific code at dw-mmc.c.
Instead, exynos specific cod can be move into exynos-dw_mmc.c.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
T4240QDS eSDHC host capabilities reigster should have VS33 bit define.
Add quirk CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 to deal with capacity
missing
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
struct mmc should be clear to all '0' after malloc to avoid
unexpect variable value.
Like mmc->has_init = xxx.
In this case mmcinfo will believe the card had been initialized before
and skip the initialization.
Test on P5040 and T4240,
Error Log:
=> mmcinfo
Device: FSL_SDHC
Manufacturer ID: 0
OEM: 0
Name: Tran Speed: 0
Rd Block Len: 0
MMC version 0.0
High Capacity: No
Capacity: 0 Bytes
Bus Width: 0-bit
=>
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Signed-off-by: Xie Shaohui-B21989 <B21989@freescale.com>
Tested-by: Ryan Barnett <rjbarnet@rockwellcollins.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
eSDHC host controller has new register to support SD Spec 3.0.
And the according host controller version was Freescale eSDHC
Version 3.0.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
SMDK5420 has a new Security Management Unit added
for dwmmc driver, hence, configuring the control
registers to support booting via eMMC.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Old command timeout value was too small and it caused I/O errors which
led to uncompleted read/write/erase operations and filesystem errors.
Timeout adaptation fixes this issue.
Changes in sdhci_send_command() function:
- change timeout variable to static
- increase default command timeout to 100 ms
- add definition of max command timeout value,
which can be redefined in each board config file
- wait for card ready state for max defined time
if it doesn't exceed defined maximum or return COMM_ERR
Once successfully increased timeout value will be used in next function
call. This fix was tested on Goni, Trats, Trats2 boards by testing UMS
on MMC storage.
Changes v2:
- move global variable cmd_timeout into function sdhci_send_command()
- change condition "==" to ">=" when comparing time with timeout
- print information about timeout increasing and card busy timeout
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
To prevent the confusion, use the get_mmc_clk() instead of mmc_clk().
get_mmc_clk() is more exactly name.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
EXT_CSD_ERASE_GROUP_DEF is lost every time after a reset or
power off. Set it if device has enhanced partitions.
Signed-off-by: Oliver Metz <oliver@freetz.org>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The patch fixes the improper read and write of sdhci
host control register for sdma transfer.
The problem comes when reading and writing 1 byte long
host control register with the sdhci_readl() and
sdhci_writel(). The misuse of these functions overwrite
the value of the next registers which are in 4 bytes boundary.
This patch replaces four byte register read/write functions
with one byte read/write ones. Beside, it eliminates
unnecessary bit operation. i.e. or-ing zero against a variable.
Signed-off-by: Juhyun (Justin) Oh <Juhyun_Oh@sigmadesigns.com>
This fixes two issues:
* a descriptor was allocated for every block, while a descriptor can
take 8 blocks
* there was an off-by-one error in the descriptor preparation: there
were two last descriptors, one with length==0
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Andy Fleming <afleming@gmail.com>
In dwmci_prepare_data, the descriptors are allocated for DMA transfer.
These are allocated using the ALLOC_CACHE_ALIGN_BUFFER. This macro uses
the stack to allocate these descriptors. This becomes a problem if the
DMA transfer continues after the processor leaves the function in which
the descriptors were allocated.
Therefore, I have moved the allocated of the buffers up one level, to
dwmci_send_cmd(). The DMA transfer should be complete when leaving this
function.
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Andy Fleming <afleming@gmail.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
For SPL builds this is just dead code since we'll only need to read.
Eliminating it results in a significant size reduction for the SPL
binary, which may be critical for certain platforms where the binary
size is highly constrained.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
If we don't have CONFIG_SPL_LIBCOMMON_SUPPORT defined then stdio
& *printf functions are unavailable & calling them will cause a link
failure.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Enable 8-bit host capability for HSMMC2 and/or HSMMC3. CONFIG_HSMMC2_8BIT
(for OMAP4/5/DRA7xx) and/or CONFIG_HSMMC3_8BIT (for DRA7xx only) must be
defined in the board header if an 8-bit eMMC device is connected to the
corresponding port.
Fix the "No status update" error that appeared for eMMC devices by
inserting a 20 us delay between writing arguments and command. This
solution has been proposed by Michael Cashwell <mboards@prograde.net>.
A minor cosmetic fix in a comment as well.
Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
"mmc_send_cmd: timeout: No status update" error sometimes happens in
omap_hsmmc driver func mmc_send_cmd() when the MMC controller card
identification and selection sequence is executed for eMMC on OMAP4
boards.
It happens due to incorrect execution of CMD line reset procedure
for OMAP4. Because CMD(DAT) lines reset procedures are slightly
different for OMAP3 and OMAP4(AM335x,OMAP5,DRA7xx).
According to OMAP3 TRM:
Set SRC(SRD) bit in MMCHS_SYSCTL register to 0x1 and wait until
it returns to 0x0.
According to OMAP4(AM335x,OMAP5,DRA7xx) TRMs, CMD(DATA) lines reset
procedure steps must be as follows:
1. Initiate CMD(DAT) line reset by writing 0x1 to SRC(SRD) bit in
MMCHS_SYSCTL register (SD_SYSCTL for AM335x).
2. Poll the SRC(SRD) bit until it is set to 0x1.
3. Wait until the SRC(SRD) bit returns to 0x0
(reset procedure is completed).
Unfortunately, at present omap_hsmmc driver has support only for
OMAP3. And as result step #2 is missing for OMAP4(AM335x,OMAP5,DRA7xx).
This sometimes leads to the fact that the waiting loop which is
required in step #3 does not executed, because SRC bit does not set
yet (at the moment of checking a condition of a loop execution).
And as a result this can cause to timeout error when sending a
next command.
In the particular case (working with eMMC witch do not respond to
some SD specific command) due to incorrect reset sequence after
command SD_CMD_SEND_IF_COND which finished with CTO flag within
64 clock cycles, the next command MMC_CMD_APP_CMD leads to a
timeout error within 1s.
So, extend CMD(DATA) lines reset procedure in func
mmc_reset_controller_fsm() by adding the missing step #2 for
OMAP4+/AM335x boards.
Signed-off-by: Oleksandr Tyshchenko <oleksandr.tyshchenko@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Do not call a memset for unused variable backup every time.
Remove unused variable from function.
Signed-off-by: Oleksandr Tyshchenko <oleksandr.tyshchenko@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Samsung SoC is supported the WIDE8, even if Controller version is v2.0.
So add the SDHCI_QUIRK_USE_WIDE8 for Samsung-SoC.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Enable support for high-capacity eMMC and MMC cards. The MXS MMC
driver has no problem with those.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Amaury Pouly <amaury.pouly@gmail.com>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
This patch cleans up license header in these files:
board/freescale/p1022ds/spl.c
drivers/mmc/fsl_esdhc_spl.c
drivers/mtd/spi/fsl_espi_spl.c
Signed-off-by: York Sun <yorksun@freescale.com>
The code from the internal on-chip ROM. It loads the final uboot image
into DDR, then jump to it to begin execution.
The SPL's size is sizeable, the maximum size must not exceed the size of L2
SRAM. It initializes the DDR through SPD code, and copys final uboot image
to DDR. So there are two stage uboot images:
* spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that
ddr spd code can get the interleaving mode setting in env. It loads
final uboot image from offset 96KB.
* final uboot image, size is variable depends on the functions enabled.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
The FTSDC010_DCR_FIFO_RST symbol is conditionally
defined in <faraday/ftsdc010.h> and it is available
available when CONFIG_FTSDC010_SDIO is enabled.
However the actual driver code unconditionally uses
the FTSDC010_DCR_FIFO_RST constant and this causes
build error if CONFIG_FTSDC010_SDIO is not enabled.
The following error happens when compiling for the
adp-ag101 board:
ftsdc010_mci.c: In function 'ftsdc010_request':
ftsdc010_mci.c:178: error: 'FTSDC010_DCR_FIFO_RST' undeclared (first use in this function)
ftsdc010_mci.c:178: error: (Each undeclared identifier is reported only once
ftsdc010_mci.c:178: error: for each function it appears in.)
The patch ensures that the FTSDC010_DCR_FIFO_RST
symbol gets used only if CONFIG_FTSDC010_SDIO is
defined.
Compile tested only.
Cc: Kuo-Jung Su <dantesu@faraday-tech.com>
Cc: Macpaul Lin <macpaul@andestech.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Reviewed-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Dealing with the sys ctrl register should touch only the
relevant bits and not accidently the whole register. On i.MX6,
the sys control register contains bits which shouldn't be reset to
0, e.g. SYS_CTRL[3-0] and IPP_RST_N (SYS_CTRL[23]).
Do this by read/modify/write instead of just a 32bit write.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Andy Fleming <afleming@freescale.com>
1. No contents of "asm/arch/clk.h" is used within "dw_mmc.c".
2. If arch doesn't have "asm/arch/clk.h" driver won't build.
Without mentioned inclusion dw_mmc driver could be built for arches
other than ARM. For ARM driver still builds without it.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Amar <amarendra.xt@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Fill the right command type when using CMD12 to stop data transfer.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
CC: Fleming Andrew-AFLEMING <AFLEMING@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
With CONFIG_SYS_64BIT_LBA, lbaint_t gets defined as a 64-bit type,
which is required to represent block numbers for storage devices that
exceed 2TiB (the block size usually is 512B), e.g. recent hard drives.
For some obscure reason, the current U-Boot code uses lbaint_t for the
number of blocks to read (a rather optimistic estimation of how RAM
sizes will evolve), but not for the starting address. Trying to access
blocks beyond the 2TiB boundary will simply wrap around and read a
block within the 0..2TiB range.
We now use lbaint_t for block start addresses, too. This required
changes to all block drivers as the signature of block_read(),
block_write() and block_erase() in block_dev_desc_t changed.
Signed-off-by: Sascha Silbe <t-uboot@infra-silbe.de>
Current DWMMC driver used to give FIFO underrun/overrun error every 3rd time
for mmc rescan command.
In current code FIFO_DEPTH is getting calculated after reading the default FIFOTH
register and extracting the RX_WMARK bits from it i.e (RX_WMARK = FIFO_DEPTH/2 -1).
Instead of storing the correct value, we were recalculating the FIFO_DEPT each
time which is not correct.
Based on "[PATCH V9 3/9] DWMMC: Initialise dwmci and resolve EMMC read write issues"
http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/160247
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Enhance the MMC core to calculate the size of each MMC partition, and
update mmc->capacity whenever a partition is selected. This causes:
mmc dev 0 1 ; mmcinfo
... to report the size of the currently selected partition, rather than
always reporting the size of the user partition.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
After waiting for the command completion event, the interrupt status
bits, that occured to be set by that time, are cleared by writing them
back. It is supposed, that it should be command related bits (command
complete and may be command errors).
However, in some cases the DMA already completes by that time before
the full transaction completes. The corresponding DINT bit gets set
and then cleared before even entering the loop, waiting for data part
completion. That waiting loop never gets this bit set, causing the
operation to hang. This is reported to happen, for example, for write
operation of 1 sector to upper area (block #7400000) of SanDisk Ultra II
8GB card.
The solution could be to explicitly clear only command related interrupt
status bits. However, since subsequent processing does not rely on
any command bits state, it could be easier just to remove clearing
of any bits at that point, leaving them all until all data processing
completes. After that the whole register will be cleared at once.
Also, on occasion, interrupts masking moved to before writing the command,
just for the case there should be no chance of interrupt between the first
command and interrupts masking.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Since commit 48e0b2bd (powerpc/esdhc: Correct judgement for DATA PIO mode)
we see mx6 systems to hang after doing a 'save' command.
Revert this commit since the original 'ifdef' logic from 7b43db92
(drivers/mmc/fsl_esdhc.c: fix compiler warnings) was the correct one.
Reported-by: Tapani Utriainen <tapani@technexion.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch fixes a bug related to mmc writes.
When doing fatwrites on an SD-Card, MMC bus problems can occur. Depending
on the size of the file, "MMC0: Bus busy timeout!" is reported, resulting
in an SD-Card that is no longer responding.
It appears to be, that set_cluster can be called with a size being zero.
That can be with a file that has a size being an exact multiple
(including 0) of the clustersize, but also for files that are smaller than
the size of one cluster.
The same problem occurs if the "mmc write" command is given with a block
count being 0.
By adding a check for the block count being zero in mmc_write_blocks
(drivers/mmc.c), this problem is solved.
Signed-off-by: Ruud Commandeur <rcommandeur@clb.nl>
Cc: Tom Rini <trini@ti.com>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Mats Karrman <Mats.Karrman@tritech.se>
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
CAP register don't have any information for 8-bit buswidth support
on 2.0 sdhci spec, only from 3.0 onwards bit[18] got this information.
Due to this misassignment in sdhci, mmc is setting 8-bit buswidth using
mmc_set_bus_width even if controller doesn't support.
Below change has code information.
"mmc: Properly determine maximum supported bus width"
(sha1: 7798f6dbd5)
Bug log: <mmc plus and emmc cards)
-------
zynq-uboot> mmcinfo
Error detected in status(0x208100)!
Device: zynq_sdhci
Manufacturer ID: fe
.....
So enable 8-bit support only for 3.0 spec using CAP and for below 3.0
assign mmc->host_caps = MMC_MODE_8BIT on respective platform driver
if host have a support.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch adds APIs to access(open / close) and to resize boot partiton of EMMC.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds FDT support for DWMMC, by reading the DWMMC node data
from the device tree and initialising DWMMC channels as per data
obtained from the node.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch enumerates dwmci and set auto stop command during
dwmci initialisation.
EMMC read/write is not happening in current implementation
due to improper fifo size computation. Hence modified the fifo size
computation to resolve EMMC read write issues.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The logic for the whether to configure for polling or DMA
was mistakenly reversed in this patch:
Commit 7b43db9211
drivers/mmc/fsl_esdhc.c: fix compiler warnings
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
CC: Sun Yusong-R58495 <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Faraday FTSDC010 is a MMC/SD host controller.
Although there is already a driver in current u-boot release,
which is modified from eSHDC and contributed by Andes Tech.
Its performance is too terrible on Faraday A36x SoC platforms,
so I turn to implement this new version of driver which is
10+ times faster than the old one.
It's carefully designed to be compatible with Andes chips,
so it should be safe to replace it.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Andy Fleming <afleming@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The mpc85xx repuires a special layout on the memory device that is
connected to the eSDHC controller interface. But the file spl_mmc.c
didn't handle this specfic case, there needs a special treatmen, in
the powerpc drictory. So, there is no longer to keep spl_mmc.c on
mpc85xx, CONFIG_SPL_FRAMEWORK is not set.
When CONFIG_SPL_MMC_SUPPORT is set and CONFIG_SPL_FRAMEWORK is not
set, there was an error in drivers/mmc/spl_mmc.c:
drivers/mmc/libmmc.o:(.got2+0x8): undefined reference to `spl_image'.
Now, the solution is to move the file "spl_mmc.c" to directory "common/spl".
Signed-off-by: Ying Zhang <b40530@freescale.com>
add mmc card support with atmel mci driver
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Using IP version for different setting
- Higher version supports 8bit mode
- Higher version bus width setting is different
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Since TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs,
rename twl6035_mmc1_poweron_ldo by a more generic palmas_mmc1_poweron_ldo
function.
Signed-off-by: Nishanth Menon <nm@ti.com>
TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs
Rename twl6035 to palmas to allow reuse across multiple current and
future platforms
As part of this change, change the CONFIG_TWL6035_POWER to
CONFIG_PALMAS_POWER and update usage of header file accordingly.
Signed-off-by: Nishanth Menon <nm@ti.com>
A malloc() followed by memset() can be simply replaced by calloc().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
If failed the add_host(), it is reasonable that return value of
add_sdhci().
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Without this additional delay, some eMMC don't negotiate properly bus width
Tested on:
- Toshiba THGBM2G8D8FBAIB
- Toshiba THGBM4G4D1HBAR
- Micron MTFC4GMVEA (the one giving the problem)
- Hynix H26M64002BNR
- SanDisk SDIN5E1-32G
Signed-off-by: Davide Bonfanti <davide.bonfanti@bticino.it>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Most of time that MMC driver spends on initializing a device is polling
OCR (operation conditions register). To decouple this polling loop,
device init is split into two parts: The first part fires the OCR query
command, and the second part polls the result. So the caller is now no
longer bound to the OCR-polling delay; he may fire the query, go
somewhere and then come back later for the result.
To use this, call mmc_set_preinit() on any device which needs this.
This can save significant amounts of time on boot (e.g. 200ms) by
hiding the MMC init time behind other init.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
log2 of the device block size serves as the shift value used to calculate
the block number to read in file systems when implementing avaiable block
sizes.
It is needed quite often in file systems thus it is pre-calculated and
stored in the block device descriptor.
Signed-off-by: Egbert Eich <eich@suse.com>
The number 512 appears quite a bit in the mmc code. Add a constant for this
so that it can be used here and in other parts of the code (e.g. SPL code
which loads from mmc).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@google.com>
block_read returns unsigned long, so it doesn't make sense to check for
< 0. and neither does marking the header structure as const and then
casting away the constness to load data into it.
Also cleanup some unneeded pointer casting while we're at it.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
Reviewed-by: Tom Rini <trini@ti.com>
The following headers are moved to a i.MX common location:
- regs-common.h
- regs-apbh.h
- regs-bch.h
- regs-gpmi.h
- dma.h
This way this header can be re-used also by other i.MX platforms.
For example the i.MX6 which will need it for the upcoming NAND
support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Support to check whether the SD3.0 or not.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Rommel Custodio <sessyargc@gmail.com>
eMMC vesrion is supported up to v4.5.
But bootloader isn't saw the exact eMMC version.
After applied this patch,
if use the mmcinfo command, then can see the exactly mmc version.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Rommel Custodio <sessyargc@gmail.com>
Rework the waiting for transfer completion loop condition
to continue waiting until both Transfer Complete and DMA End
interrupts occur. Checking of DLA bit in Present State register
looks not needed in addition to interrupts status checking,
so it can be removed from the condition. Also, DMA Error
condition is added to the list of data errors, checked in the loop.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
The cache should invalidate the read buffer for
the SD card interface after the transfer complete,
not command-complete.
Tested-by: Andrew Gabbasov <Andrew_Gabbasov@mentor.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Apparently, CONFIG_SYS_HZ must be 1000. Change this, and fix the timer
driver to conform to this.
Have the timer implementation export a custom API get_timer_us() for use
by the BCM2835 MMC API, which needs us resolution for a HW workaround.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Maximum bus width supported by some i.MX6 boards is not 8bit like
others. In case where both host controller and card support 8bit transfers,
they agree to communicate on 8bit interface while some boards support only 4bit interface.
Due to this reason the mmc 8bit default mode fails on these boards. To rectify this,
define maximum bus width supported by these boards (4bit). If max_bus_width is not
defined, it is 0 by default and 8bit width support will be enabled in host
capabilities otherwise host capabilities are modified accordingly.
It is tested with a MMCplus card.
Signed-off-by: Abbas Raza <Abbas_Raza@mentor.com>
cc: stefano Babic <sbabic@denx.de>
cc: Andy Fleming <afleming@gmail.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Gets rid of warnings from omap_gpio:
ERROR : check_gpio: invalid GPIO -1
(and undefined behaviour as the -1 error code is interpreted as gpio value)
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
Let mmc_getcd() return true and mmc_getwp() false if mmc driver doesn't
provide handlers for them.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
[trini: Add braces around first if test in each case to fix warning]
Signed-off-by: Tom Rini <trini@ti.com>
This adds a simple driver for the BCM2835's SD controller.
Workarounds are implemented for:
* Register writes can't be too close to each-other in time, or they will
be lost.
* Register accesses must all be 32-bit, so implement custom accessors.
This code was extracted from:
git://github.com/gonzoua/u-boot-pi.git master
which was created by Oleksandr Tymoshenko.
Portions of the code there were obviously based on the Linux kernel at:
git://github.com/raspberrypi/linux.git rpi-3.6.y
commit f5b930b "Main bcm2708 linux port" signed-off-by Dom Cobley.
swarren changed the following for upstream:
* Removed hack udelay()s in bcm2835_sdhci_raw_writel(); setting
SDHCI_QUIRK_WAIT_SEND_CMD appears to solve the issues.
* Remove register logging from read*/write* functions.
* Sort out confusion with min/max_freq values passed to add_sdhci().
* Use more descriptive variable names and calculations in IO accessors.
* Simplified and commented twoticks_delay calculation.
* checkpatch fixes.
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Oleksandr Tymoshenko <gonzo@bluezbox.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Andy Fleming <afleming@gmail.com>
Tegra30 requires the SD Bus Voltage & Power bits be set in the SD
Power Control register. Tegra20 works w/o them set, but do it anyway
for those SoCs as it's part of the SD spec. Also call a common
board pad init routine (pad_init_mmc) in mmc_reset(), used by
Tegra30 only for now.
Note that Tegra20 SD/MMC HW differs enough from Tegra20 that a
new compatible entry is used in the fdt compat_names/id tables.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
tegra_mmc_init() now parses the DT info for bus width, WP/CD GPIOs, etc.
Tested on Seaboard, fully functional.
Tamonten boards (medcom-wide, plutux, and tec) use a different/new
dtsi file w/common settings.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
This patch changes sdhci_init()'s behavior to NOT enable all interrupt
sources by default. Moreover interrupt signaling has been disabled.
This patch do not enable interrupts which aren't served in u-boot
(they are defined at sdhci.h but NOT used elsewhere):
- SDHCI_INT_CARD_INSERT, SDHCI_INT_CARD_REMOVE, SDHCI_BUS_POWER,
SDHCI_INT_CARD_REMOVE, SDHCI_INT_CARD_INT
Special care shall be put on SDHCI_INT_CARD_INT, which indicates
interrupt generated by SD card.
According to "SD Host Controller Simplified Spec. ver 3.00" when bit 8
(Card Interrupt Status Enable) at "Normal Interrupt Status Enable
Register" (offset 0x34) is set, the card interrupt detection is started.
Then eMMC card may cause the SD controller to set this bit and then this
interrupt is passed to booted OS and might cause kernel crash.
To sum up:
- Only enable interrupts, which are served at u-boot
- This cleanup as a side effect fixes SDHCI's CARD INTERRUPT problem at
Linux kernel (versions 3.6+, sdhci controller)
- Keep masked bits at "Normal Interrupt Signal Enable Register" (0x38h)
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Andy Fleming <afleming@freescale.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
In master we had already taken a patch to fix the davinci GPIO code for
CONFIG_SOC_DM646X and in u-boot-ti we have additional patches to support
DA830 (which is CONFIG_SOC_DA8XX && !CONFIG_SOC_DA850). Resolve these
conflicts manually and comment the #else/#endif lines for clarity.
Conflicts:
arch/arm/include/asm/arch-davinci/gpio.h
drivers/gpio/da8xx_gpio.c
Signed-off-by: Tom Rini <trini@ti.com>
A seperate omap_sys_ctrl_regs structure is defined for
omap4 & 5. If there is any change in control module for
any of the ES versions, a new structure needs to be created.
In order to remove this dependency, making the register
structure generic for all the omap4+ boards.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Currently there's no appropriate place to store driver specific data
because the pointer that is meant for that (priv) is being used to
store the base address of mmc registers.
Introduce a new struct for storing driver specific data.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
There are 3 MMC/SD/SDIO controllers in OMAP SoCs, but only 2 structs
are defined for devices. This leads to data being written outside of
array bounds on systems that use all 3 controllers.
Update hsmmc_dev array to the correct size.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
This patch streamlines the differences between the MX23 and MX28 by
implementing a few helper functions to handle different DMA channel
mapping, different clock domain for SSP block and fixes a few minor
bugs.
First of all, the DMA channel mapping is now fixed in dma.h by defining
the actual channel map for both MX23 and MX28. Thus, MX23 now does no
longer use MX28 channel map which was wrong. Also, there is a fix for
MX28 DMA channel map, where the last four channels were incorrect.
Next, because correct DMA channel map is in place, the mxs_dma_init_channel()
call now bases the channel ID starting from SSP port #0. This removes the
need for DMA channel offset being added and cleans up the code. For the
same reason, the SSP0 offset can now be used in mxs_dma_desc_append(), thus
no need to adjust dma channel number in the driver either.
Lastly, the SSP clock ID is now retrieved by calling mxs_ssp_clock_by_bus()
which handles the fact that MX23 has shared SSP clock for both ports, while
MX28 has per-port SSP clock.
Finally, the mxs_ssp_bus_id_valid() pulls out two implementations of the
same functionality from MMC and SPI driver into common code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Add rsi/sdh support for bf60x.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Sonic Zhang <sonic.adi@gmail.com>
The MX23 has different layout of DMA channels. Fix the MMC
driver to support MX23.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Some MXS based boards do not implement the card-detect signal. Allow
user to specify alternate card-detect implementation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
This does the same reset mask as done in v3.7 Linux kernel code.
The block is properly configured for MMC operation that way.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
The MX23 can only use two SSP ports.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Create function which converts SSP bus number to SSP register pointer.
This functionality is reimplemented multiple times in the code, thus
make one common implementation. Moreover, make it a switch(), since the
SSP ports are not mapped in such nice linear fashion on MX23, therefore
having it a switch will simplify things there.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
The clock data are not used by the driver, drop them.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
All esdhc variants we know should support high capacity MMC cards,
so let's add MMC_MODE_HC host_caps unconditionally to support those
MMC cards (capacity > 2 GB).
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
At some point, a confusion arose about the use of the bit
definitions in host_caps for bus widths, and the value
in ext_csd. By coincidence, a simple shift could convert
between one and the other:
MMC_MODE_1BIT = 0, EXT_CSD_BUS_WIDTH_1 = 0
MMC_MODE_4BIT = 0x100, EXT_CSD_BUS_WIDTH_4 = 1
MMC_MODE_8BIT = 0x200, EXT_CSD_BUS_WIDTH_8 = 2
However, as host_caps is a bitmask of supported things,
there is not, in fact, a one-to-one correspondence. host_caps
is capable of containing MODE_4BIT | MODE_8BIT, so nonsensical
things were happening where we would try to set the bus width
to 12.
The new code clarifies the very different namespaces:
host_caps/card_caps = bitmask (MMC_MODE_*)
ext CSD fields are just an index (EXT_CSD_BUS_WIDTH_*)
mmc->bus_width integer number of bits (1, 4, 8)
We create arrays to map between the namespaces, like in Linux.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tegra's MMC driver does DMA, and hence needs cache-aligned buffers. In
some cases (e.g. user load commands) this cannot be guaranteed by callers
of the MMC APIs. To solve this, modify the Tegra MMC driver to use the
new bounce_buffer_*() APIs.
Note: Ideally, all U-Boot code will always provide address- and size-
aligned buffers, so a bounce buffer will only ever be needed for user-
supplied buffers (e.g. load commands). Ensuring this removes the need
for performance-sucking bounce buffer cache management and memcpy()s.
The one known exception at present is the SCR buffer in sd_change_freq(),
which is only 8 bytes long. Solving this requires enhancing struct
mmc_data to know the difference between buffer size and transferred data
size, or forcing all callers of mmc_send_cmd() to have allocated buffers
using ALLOC_CACHE_ALIGN_BUFFER(), which while true in this case, is not
enforced in any way at present, and so cannot be assumed by the core MMC
code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The current bouncebuf API requires all parameters to be passed to both
bounce_buffer_start() and bounce_buffer_stop(). Modify the bouncebuf
start function to accept a state structure as a parameter, and only
require that state struct to be passed to the stop function. This
simplifies usage of the bounce buffer by clients.
Don't modify the data pointer, but rather store the temporary buffer in
this state struct. The bouncebuf code ensures that client code can
always use a single buffer pointer in the state structure, irrespective
of whether a bounce buffer actually had to be allocated.
Move cache management logic into the bounce buffer code, so that each
client doesn't have to duplicate this. I believe there's no need to
invalidate the buffer before a DMA operation, since flushing the cache
should prevent any write-backs.
Update the MXS MMC driver for this change.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Bring in the code from Linux kernel.
Added to Linux kernel by:
commit e08c1694d9e2138204f2b79b73f0f159074ce2f5
Author: Andres Salomon <dilinger@queued.net>
Date: Fri Jul 4 10:00:03 2008 -0700
Some HW balks when writing both voltage setting and power up at the same
time to SDHCI_POWER_CONTROL register.
Signed-off-by: Rommel G Custodio <sessyargc@gmail.com>
CC: Andy Fleming <afleming@freescale.com>
v2: fix attribution and SOB
Signed-off-by: Andy Fleming <afleming@freescale.com>
The interpretation of the data returned by the MMC_CMD_ALL_SEND_CID
command was incorrect with respect to the JEDEC Standard No. 84-A441.
This change makes the interpretation correct with respect to the
defined fields of the CID register.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Taylor Hutt <thutt@chromium.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
If a board has all 8 data lines routed, the SD/MMC controller can still
operate in 4-bit (or presumably even 1-bit) mode. Adjust Tegra's MMC
driver to report the 4-bit capability even for 8-bit slots.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
fsl_esdhc.c:71:6: warning: symbol 'esdhc_xfertyp' was not declared. Should it be static?
fsl_esdhc.c:413:6: warning: symbol 'set_sysctl' was not declared. Should it be st
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
mmc.c:137:5: warning: symbol 'mmc_send_cmd' was not declared. Should it be static?
mmc.c:203:5: warning: symbol 'mmc_send_status' was not declared. Should it be static?
mmc.c:247:5: warning: symbol 'mmc_set_blocklen' was not declared. Should it be static?
mmc.c:440:5: warning: symbol 'mmc_read_blocks' was not declared. Should it be static?
mmc.c:510:5: warning: symbol 'mmc_go_idle' was not declared. Should it be static?
mmc.c:532:1: warning: symbol 'sd_send_op_cond' was not declared. Should it be static?
mmc.c:597:5: warning: symbol 'mmc_send_op_cond' was not declared. Should it be static?
mmc.c:661:5: warning: symbol 'mmc_send_ext_csd' was not declared. Should it be static?
mmc.c:683:5: warning: symbol 'mmc_switch' was not declared. Should it be static?
mmc.c:705:5: warning: symbol 'mmc_change_freq' was not declared. Should it be static?
mmc.c:775:5: warning: symbol 'sd_switch' was not declared. Should it be static?
mmc.c:796:5: warning: symbol 'sd_change_freq' was not declared. Should it be static?
mmc.c:935:6: warning: symbol 'mmc_set_ios' was not declared. Should it be static?
mmc.c:953:6: warning: symbol 'mmc_set_bus_width' was not declared. Should it be static?
mmc.c:1108:26: warning: dubious: !x & y
mmc.c:960:5: warning: symbol 'mmc_startup' was not declared. Should it be static?
mmc.c:1243:5: warning: symbol 'mmc_send_if_cond' was not declared. Should it be s
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This driver is no longer used and it's remaining users were converted
to the new generic PXA MMC driver. Thus, remove this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
MMC host controller requires a delay between every sdhci_send_cmd()
execution. In s5p_mmc driver (s5p_sdhci replaces this driver), a delay
of 1000us was provided after every mmc_send_cmd() call. Adding a quirk
in current sdhci driver to replicate the behaviour.
Without this delay, MMC initialization on Origen board fails with
following error messages.
Timeout for status update!
mmc fail to send stop cmd
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
In host-control register, DMA select bit field is present.
BUt in sdhci.c, didn't select for DMA.
if set CONFIG_MMC_SDMA, we need to set SDMA-select bit.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Timeout value is tunable.
When run read/write operation, sometime returned the timeout error.
Because the timeout value is too short.
So increased the enough timeout value.
(This timeout value is used to prevent the infinite loop.)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The recent removal of the cmd->flags field caused error in the
debuging code of mmc_spi. Fix this:
mmc_spi.c: In function 'mmc_spi_request':
mmc_spi.c:179:2: error: 'struct mmc_cmd' has no member named 'flags'
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Implement necessary code to use the generic bounce buffer routines
inside this driver. This replaces the MMC bounce buffer, which is
to be removed.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Since the at91sam9263, the mmc hardware support multi blocks read/write. So this driver enable it.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
On mxc, each SDHC instance has a dedicated clock, so gd->sdhc_clk is not
suitable for the multi-instance use case (initialization made directly with
fsl_esdhc_initialize()).
This patch fixes this issue by adding a configuration field for the SDHC input
clock frequency.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Jason Liu <r64343@freescale.com>
Cc: Matt Sealey <matt@genesi-usa.com>
Cc: Andy Fleming <afleming@gmail.com>
The move is pretty straight-forward. ap20.h and tegra20.h were renamed to ap.h and tegra.h.
Some files remain in arch-tegra20 but 'include' a file in 'arch-tegra' with #defines & structs
that will be common between T20 and T30 HW. HW-specific #defines, etc. stay in the 'arch-tegra20'
'root' file.
All boards build OK w/MAKEALL -s tegra20. Checkpatch.pl runs clean. Seaboard works OK.
Signed-off-by: Tom Warren <twarren@nvidia.com>
- Convert the non-relocation part of board_init_f to spl_board_init, turn on CONFIG_SPL_BOARD_INIT in the configs.
- Remove duplicated code.
- Add spl_boot_device() that returns the statically chosen boot device.
Signed-off-by: Tom Rini <trini@ti.com>
Add a new flag, CONFIG_SPL_FRAMEWORK to opt into the common/spl SPL
framework, enable on all of the previously using boards. We move the
spl_ymodem.c portion to common/ and spl_mmc.c to drivers/mmc/. We leave
the NAND one in-place as we plan to replace it later in this series.
We use common/spl to avoid linker problems with respect to merging
constant strings in objects. Otherwise all strings in common/ will be
linked in and kept which grows SPL in size too much.
Signed-off-by: Tom Rini <trini@ti.com>
Convert TEGRA20_ defines to either TEGRA_ or NV_PA_ where appropriate.
Convert tegra20_ source file and function names to tegra_, also.
Upcoming Tegra30 port will use common code/defines/names where possible.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Some eMMC devices contain boot partitions, but do not set the PART_SUPPORT
bit in EXT_CSD_PARTITIONING_SUPPORT. Allow partition selection on such
devices, by enabling partition switching when EXT_CSD_BOOT_MULT is set.
Note that the Linux kernel enables access to boot partitions solely based
on the value of EXT_CSD_BOOT_MULT; EXT_CSD_PARTITIONING_SUPPORT only
influences access to "general" partitions.
eMMC devices affected by this issue exist on various NVIDIA Tegra
platforms (and presumably many others too), such as Harmony (plug-in eMMC),
Seaboard, Springbank, and Whistler (plug-in eMMC).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
There were a couple of drivers that were actually using the flags
field of the cmd structure, despite the fact that no one ever
*set* that field. When we removed the field, those drivers failed
to compile. Replaced the references with the correct usage of
resp_type.
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch prevents dcache-related problem. The problem manifested
itself on the SPI driver, this is just a port to the MMC driver.
The scenario is the same. In case an "mmc read" is issued to a
buffer which was written right before it and data cache is enabled,
the cache eviction might happen during the DMA transfer into the
buffer, therefore corrupting the buffer. Clear any cache lines that
might contain the buffer to prevent such issue.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Samsung SoC use the cmu control to set clock.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Useless code is removed, and get buswidth value.
buswidth value will be used to choice the 4bit or 8bit.
(Now used 4bit mode in sdhci.c by default)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Samsung SoC is broken busy waiting for R1b type.
And clk delay control value is modified the previosuly value.
(that value used at the s5p_mmc.c)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Some boards have no Card Detect wired. In that case, set the CD test
bits in the standard interface.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When setting up the clocks in the sdhci driver, the "spec version"
must be masked off. Otherwise any time the vendor version is not 0,
the check will allways assume the interface is version 3. This breaks
when the interface is actually version 1 or 2.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Some eMMC devices contain boot partitions, but do not set the PART_SUPPORT
bit in EXT_CSD_PARTITIONING_SUPPORT. Allow partition selection on such
devices, by enabling partition switching when EXT_CSD_BOOT_MULT is set.
Note that the Linux kernel enables access to boot partitions solely based
on the value of EXT_CSD_BOOT_MULT; EXT_CSD_PARTITIONING_SUPPORT only
influences access to "general" partitions.
eMMC devices affected by this issue exist on various NVIDIA Tegra
platforms (and presumably many others too), such as Harmony (plug-in eMMC),
Seaboard, Springbank, and Whistler (plug-in eMMC).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Since the type of "ext_csd" was array of char, the following
calculation might fail when the value of ext_csd[EXT_CSD_SEC_CNT]
was minus.
capacity = ext_csd[EXT_CSD_SEC_CNT] << 0
| ext_csd[EXT_CSD_SEC_CNT + 1] << 8
| ext_csd[EXT_CSD_SEC_CNT + 2] << 16
| ext_csd[EXT_CSD_SEC_CNT + 3] << 24;
So, this patch changes the type of "ext_csd" to array of u8.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The controller can control high capacity cards. So, the patch adds
the flag. If the flag is not set, "mmcinfo" will fail when a high
capacity card is used.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
(!timeout) condition check in mmc_send_status() can never be met,
because do-while loop ends up with negative timeout value, -1.
Fix the check to handle TIMEOUT case correctly.
Signed-off-by: Jongman Heo <jongman.heo@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The cache snooping feature of Freescale's eSDHC IP is not available on i.MX, so
disable it globally for this architecture. This avoids setting no_snoop for all
i.MX boards, and it prevents setting a reserved bit of a reserved register if
fsl_esdhc_mmc_init() is used on i.MX, like in
arch/arm/cpu/armv7/imx-common/cpu.c/cpu_mmc_init().
Since no_snoop was only used on i.MX, get rid of it BTW.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
The sys_proto.h functions (except the boot modes) are compatible with
i.MX233 and i.MX28 so we use 'mxs' prefix for its methods.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This is make naming consistent with the kernel and devicetree and in
preparation of pulling out the common tegra20 code.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Configuration in vexpress and u8500.v1 is different from what
is needed in u8500.v2. As such, card configuration specifics need
to reside in the board file rather than the driver.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Tom Rini <trini@ti.com>
The DMA didn't work properly because the DMA descriptor wasn't
properly cleaned after it was used once. Also, the DMA_ENABLE bit
was enabled/disabled too late.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Large blocks (> 512b) shall be transfered via DMA to make
things a bit faster.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Move DMA and PIO data transfer parts into separate functions.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
The DMA mode didn't properly configure the DMA_ENABLE bit in CTRL1.
Also, it was using SSP0 DMA channel for all SSP devices.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
DA850/OMAP-L138 does not support strict MMC/SD boot mode. SPL will
be in SPI flash and U-Boot image will be in MMC/SD card. SPL will
do the low level initialization and then loads the u-boot image
from MMC/SD card.
Define CONFIG_SPL_MMC_LOAD macro in the DA850/OMAP-L138
configuration file to enable this feature.
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
For FSL low-end processors (VVN2.2), in order to detect the SD card,
we should enable PEREN, HCKEN and IPGEN to enable the clock.
Otherwise, after booting the u-boot, and then inserting the SD card,
the SD card can't be detected.
For SDHC VVN2.3 IP, these bits are reserved, and SDCLKEN is used.
And when accessing to these reserved bit, no any impact happened.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
CC: Andy Fleming <afleming@gmail.com>
CC: Marek Vasut <marex@denx.de>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Use the function 'mmc_send_status' to check the card status.
only when the card is ready, driver can send the next erase command
to the card, otherwise, the erase will failed:
=> mmc erase 0 1
MMC erase: dev # 0, block # 0, count 1 ... 1 blocks erase: OK
=> mmc erase 0 2
MMC erase: dev # 0, block # 0, count 2 ... mmc erase failed
1 blocks erase: ERROR
=> mmc erase 0 4
MMC erase: dev # 0, block # 0, count 4 ... mmc erase failed
1 blocks erase: ERROR
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
CC: Andy Fleming <afleming@gmail.com>
CC: Marek Vasut <marex@denx.de>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This code adds call to mmc_init(), for partition related commands (e.g.
fatls, fatinfo etc.).
It is safe to call mmc_init() multiple times since mmc->has_init flag
prevents from multiple initialization.
The FAT related code calls get_dev high level method and then uses
elements from mmc->block_dev, which is uninitialized until the mmc_init
(and thereof mmc_startup) is called.
This problem appears on boards, which don't use mmc as the default
place for envs
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
mmc_set_clock is set to the hard-coding.
But i think good that use the tran_speed value.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
In anticipation of Tegra3 support, continue removing/renaming
Tegra2-specific files. No functional changes (yet).
Updated copyrights to 2012.
Signed-off-by: Tom Warren <twarren@nvidia.com>
* 'master' of git://git.denx.de/u-boot-arm: (167 commits)
OMAP4/5: Change omap4_sdp, omap4_panda, omap5_evm maintainer
ARM: omap3: Add CONFIG_SPL_BOARD_INIT for CONFIG_SPL_MMC_SUPPORT
ARM: omap3: Set SPL stack size to 8KB, image to 54KB.
arm, omap3: fix warm reset serial output on OMAP36xx/AM/DM37xx
OMAP4: Set fdt_high for OMAP4 devices to enable booting with Device Tree
omap4: do not enable auxiliary cores
omap4: do not enable fs-usb module
omap4: panda: disable uart2 pads during boot
igep00x0: change mpurate from 500 to auto
igep00x0: enable the use of a plain text file
tegra2: trivially enable 13 mhz crystal frequency
tegra: Enable keyboard for Seaboard
tegra: Switch on console mux and use environment for console
tegra: Add tegra keyboard driver
tegra: fdt: Add keyboard definitions for Seaboard
tegra: fdt: Add keyboard controller definition
tegra: Add keyboard support to funcmux
input: Add support for keyboard matrix decoding from an fdt
input: Add generic keyboard input handler
input: Add linux/input.h for key code support
fdt: Add fdtdec functions to read byte array
tegra: Enable LP0 on Seaboard
tegra: fdt: Add EMC data for Tegra2 Seaboard
tegra: i2c: Add function to find DVC bus
fdt: tegra: Add EMC node to device tree
tegra: Add EMC settings for Seaboard
tegra: Turn off power detect in board init
tegra: Set up warmboot code on Nvidia boards
tegra: Setup PMC scratch info from ap20 setup
tegra: Add warmboot implementation
tegra: Set up PMU for Nvidia boards
tegra: Add PMU to manage power supplies
tegra: Add EMC support for optimal memory timings
tegra: Add header file for APB_MISC register
tegra: Add tegra_get_chip_type() to detect SKU
tegra: Add flow, gp_padctl, fuse, sdram headers
tegra: Add crypto library for warmboot code
tegra: Add functions to access low-level Osc/PLL details
tegra: Move ap20.h header into arch location
Add AES crypto library
i2c: Add TPS6586X driver
Add abs() macro to return absolute value
fdt: Add function to return next compatible subnode
fdt: Add function to locate an array in the device tree
i.MX28: Avoid redefining serial_put[cs]()
i.MX28: Check if WP detection is implemented at all
i.MX28: Add battery boot components to SPL
i.MX28: Reorder battery status functions in SPL
i.MX28: Add LRADC init to i.MX28 SPL
i.MX28: Add LRADC register definitions
i.MX28: Shut down the LCD controller before reset
i.MX28: Add LCDIF register definitions
i.MX28: Implement boot pads sampling and reporting
i.MX28: Improve passing of data from SPL to U-Boot
M28EVK: Add SD update command
M28EVK: Implement support for new board V2.0
FEC: Abstract out register setup
MX5: PAD_CTL_DRV_VOT_LOW and PAD_CTL_DRV_VOT_HIGH exchanged
i.MX28: Add delay after CPU bypass is cleared
spi: mxs: Allow other chip selects to work
spi: mxs: Introduce spi_cs_is_valid()
mx53loco: Remove unneeded gpio_set_value()
mx53loco: Add CONFIG_REVISION_TAG
mx53loco: Turn on VUSB regulator
mx53loco: Add mc34708 support and set mx53 frequency at 1GHz
pmic: dialog: Avoid name conflicts
imx: Add u-boot.imx as target for ARM9 i.MX SOCs
i.MX2: Include asm/types.h in arch-mx25/imx-regs.h
imx: usb: There is no such register
i.MX25: usb: Set PORTSCx register
imx: nand: Support flash based BBT
i.MX25: This architecture has a GPIO4 too
i.MX25: esdhc: Add mxc_get_clock infrastructure
i.MX6: mx6q_sabrelite: add SATA bindings
i.MX6: add enable_sata_clock()
i.MX6: Add ANATOP regulator init
mx28evk: add NAND support
USB: ehci-mx6: Fix broken IO access
M28: Scan only first 512 MB of DRAM to avoid memory wraparound
Revert "i.MX28: Enable additional DRAM address bits"
M28: Enable FDT support
mx53loco: Add support for 1GHz operation for DA9053-based boards
mx53loco: Allow to print CPU information at a later stage
mx5: Add clock config interface
imx-common: Factor out get_ahb_clk()
i.MX6Q: mx6qsabrelite: Add keypress support to alter boot flow
mx31pdk: Allow booting a zImage kernel
mx6qarm2: Allow booting a zImage kernel
mx6qsabrelite: Allow booting a zImage kernel
mx28evk: Allow booting a zImage kernel
m28evk: Allow to booting a dt kernel
mx28evk: Allow to booting a dt kernel
mx6qsabrelite: No need to set the direction for GPIO3_23 again
pmic: Add support for the Dialog DA9053 PMIC
MX53: mx53loco: Add SATA support
MX53: Add support to ESG ima3 board
SATA: add driver for MX5 / MX6 SOCs
MX53: add function to set SATA clock to internal
SATA: check for return value from sata functions
MX5: Add definitions for SATA controller
NET: fec_mxc.c: Add a way to disable auto negotiation
Define UART4 and UART5 base addresses
EXYNOS: Change bits per pixel value proper for u-boot.
EXYNOS: support TRATS board display function
LCD: support S6E8AX0 amoled driver based on EXYNOS MIPI DSI
EXYNOS: support EXYNOS MIPI DSI interface driver.
EXYNOS: support EXYNOS framebuffer and FIMD display drivers.
LCD: add data structure for EXYNOS display driver
EXYNOS: add LCD and MIPI DSI clock interface.
EXYNOS: definitions of system resgister and power management registers.
SMDK5250: fix compiler warning
misc:pmic:samsung Convert TRATS target to use MAX8997 instead of MAX8998
misc:pmic:max8997 MAX8997 support for PMIC driver
TRATS: modify the trats's configuration
ARM: Exynos4: ADC: Universal_C210: Enable LDO4 power line for ADC measurement
EXYNOS: Rename exynos5_tzpc structure to exynos_tzpc
arm: ea20: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
arm: cam_enc_4xx: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
cm-t35: add I2C multi-bus support
include/configs: Remove CONFIG_SYS_64BIT_STRTOUL
include/configs: Remove CONFIG_SYS_64BIT_VSPRINTF
omap3: Introduce weak misc_init_r
omap730p2: Remove empty misc_init_r
omap5912osk: Remove empty misc_init_r
omap4+: Remove CONFIG_ARCH_CPU_INIT
omap4: Remove CONFIG_SYS_MMC_SET_DEV
OMAP3: pandora: drop console kernel argument
OMAP3: pandora: revise GPIO configuration
...
If the WP function is NULL, simply assume the card is always RW.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Make the sysctrl structure common, so that it can
be used in generic functions across socs.
Also change the base address of the system control module, to
include all the registers and not simply the io regs.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Add parameters to the OMAP MMC initialization function so the board can
mask host capabilities and set the maximum clock frequency. While the
OMAP supports a certain set of MMC host capabilities, individual boards
may be more restricted and the OMAP may need to be configured to match
the board. The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example.
Signed-off-by: Jonathan Solnit <jsolnit@gmail.com>
In driver mmc, generic s5p_sdhci code is implemented.
s5p_mmc file is dupulicated.
we are good that use the generic sdhci.
This patch supported the sdhci for Samsung-SoC.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Lei Wen<leiwen@marvell.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
To support the Samsung-SoC, added the basically functions.
Samsung-SoC didn't used the SDHCI_CTRL_HISPD.
And added set_control_reg callback for s3c64xx.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Lei Wen<leiwen@marvell.com>
When response type is R1b, mask value is added the SDHCI_INT_DAT_END.
but in while(), didn't check that flag.
So sdhci controller didn't work fine.
CMD6 didn't always complete.
So add the quirks for broken r1b response
and add the timeout value to prevent the infinite loop.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Lei Wen<leiwen@marvell.com>
Some MMC cards, like my ancient 32.0MB SanDisk RS-MMC cards had issue if b_max
was set to 0x40 and DMA was enabled. Lower this value to 0x20, which allows
these cards to work too.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
This patch imports parts of two patches from the Freescale U-Boot with the following
commit messages:
ENGR00156405 ESDHC: Add workaround for auto-clock gate errata ENGcm03648
http://git.freescale.com/git/cgit.cgi/imx/uboot-imx.git/commit/drivers/mmc/imx_esdhc.c?h=imx_v2009.08_12.01.01&id=e436525a70fe47623d346bc7d9f08f12ff8ad787
The errata, not applicable to USDHC, causes ESDHC to shut off clock to the card
when auto-clock gating is enabled for commands with busy signalling and no data
phase. The card might require the clock to exit the busy state, so the workaround
is to disable the auto-clock gate bits in SYSCTL register for such commands. The
workaround also entails polling on DAT0 bit in the PRSSTAT register to learn when
busy state is complete. Auto-clock gating is re-enabled at the end of busy state.
ENGR00156670-1 ESDHC/USDHC: Remove delay before each cmd and some bug fixes
http://git.freescale.com/git/cgit.cgi/imx/uboot-imx.git/commit/drivers/mmc/imx_esdhc.c?h=imx_v2009.08_12.01.01&id=a77c6fec8596891be96b2cdbc742c9824844b92a
Removed delay of 10 ms before each command. There should not be a need to have this
delay after the ENGR00156405 patch that polls until card is not busy anymore before
proceeding to next cmd.
This patch imports the polling part of both patches. The auto-clock gating code
don't apply for i.MX6 as implemented in these two patches.
SYSCTL_RSTA was defined twice. Remove one definition.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Andy Fleming <afleming@freescale.com>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Stefano Babic <sbabic@denx.de>
According to OMAP3 TRM, when the controller reports certain errors,
driver must perform a software reset. This is done by setting a bit
in SYSCTL and waiting it to clear:
- SRC on command timeout (CTO)
- SRD on data errors (DTO, DCRC and DEB)
This fixes a problem seen on OMAP3 pandora board with some cards
that won't work with a message printed multiple times:
timedout waiting on cmd inhibit to clear
Code loosely based on Linux omap_hsmmc driver.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Tom Rini <trini@ti.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
The message didn't state that it's waiting for STAT to _clear_,
and printing the STAT value itself can help to identify problems.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Tom Rini <trini@ti.com>
According to OMAP3 TRM, PBIASLITEPWRDNZ bits must be cleared while MMC
power supply is being enabled and is ramping up (those bits might be
left set by the previous bootloader). It doesn't say what happens if
this procedure is violated, but better not to risk here and do things
as required.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Tom Rini <trini@ti.com>
This patch sets the MMC width according to the MMC host capabilities.
It turned out, that there are some targets (e.g. GONI), which are able
to read data from SPI only at 4 bit mode.
This patch restricts the width number according to the MMC host.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Andy Fleming <afleming@gmail.com>
No other driver sets up the part type to DOS in their init, and it
doesn't seem to be needed as `mmcinfo` and `mmc part` stll work, so
drop it.
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Fix the warning
mmc.c: In function 'mmc_send_cmd':
mmc.c:87: warning: assignment from incompatible pointer type
in case CONFIG_MMC_TRACE is enabled.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Andy Fleming <afleming@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
This fixes the issue where mxs_dma_init() was called either twice or never,
without introducing any new init hooks.
The idea is to allow each and every device using the APBH DMA block to
configure and request only the channels it uses, instead of making it call init
for all the channels as is now.
The common DMA block init part, which only configures the block, is then called
from CPUs arch_cpu_init() call.
NOTE: This patch depends on:
http://patchwork.ozlabs.org/patch/150957/
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
This SD DMA function of i.MX28 is still apparently too experimental to be
enabled by default in 2012.04 release. Enable this feature only if the user
plans to tinker with DCache or explicitly enables it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Fix:
mmc.c: In function 'mmc_bounce_buffer_start':
mmc.c:132:13: warning: no return statement in function returning
non-void [-Wreturn-type]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Fix:
tegra2_mmc.c: In function 'mmc_send_cmd':
tegra2_mmc.c:230:3: warning: 'mask' may be used uninitialized in this
function [-Wuninitialized]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Tom Warren <twarren@nvidia.com>
This utilizes the newly introduced bounce buffers in the MMC layer.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
This implements generic bounce buffer at the end of MMC command submission
chain. Therefore if unaligned data are passed, they are copied. This stuff
should be pushed down into the MMC subsystem to squash all places generating
these unaligned data.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@gmail.com>
All boards are using the gen_atmel_mci driver now, so no need
to carry the old driver around.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
gen_atmel_mci works on AVR32 as well, so no need to use the legacy
mmc driver. This also has the nice side effect of being able to use
SDHC cards an those boards.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Align the card status polling with the Linux kernel and retry the
command at least five times. Also some cards apparently mishandle the
status bits, so make sure to check the card state too.
Signed-off-by: Jan Kloetzke <jan.kloetzke@dspg.com>
Cc: Andy Fleming <afleming@gmail.com>
A MMC/SD card may always go into the programming state (and hence be
busy) after a block write. Therefore always check the card state, even
after single block writes. On the other hand there is no need to check
the card status after a read.
Also make sure that errors during busy polling are propagated upwards.
Signed-off-by: Jan Kloetzke <jan.kloetzke@dspg.com>
Cc: Andy Fleming <afleming@gmail.com>
We are seeing occasional timeouts in the Tegra mmc code when
we are reading from external MMC cards. These don't seem to be
detrimental if they are handled properly. This CL properly
clears the "normal interrupt status register" (norintsts) in
error conditions. If we don't do this, when we come back into
mmc_send_cmd() the register will still contain status from the
last transaction.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Before we can send a command we need both the DATI (command inhibit on
mmc_dat line) bit and CMDI (command inhibit on mmc_cmd line) are clear.
The previous behavior of only checking on DATI was insufficient on some
cards and incorrect behavior in any case. This makes the code check
for both bits being clear and makes the error print more clear as
to what happened. DATI_CMDDIS is removed as it was unused elsewhere
in the code and stood for 'DATI is set, cmds are disabled still'.
Fix originally spotted by Peter Bigot.
Tested-by: Peter A. Bigot <bigotp@acm.org>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Andreas Müller <schnitzeltony@googlemail.com>
This patch modifies mxcmmc.c to be used
not only by i.MX27 but also by i.MX31 boards.
Both use the same SD controller, but have different
clock set-ups.
The i.MX27 imx_get_XXXclock functions are made static to
generic.c and a public mxc_get_clock() function
is provided. Pins, base address and prototypes for
an i.MX31 specific board_init_mmc() are provided.
Some of the i.MX27 clock getters are unused and marked
as such to avoid warnings (./MAKEALL -s mx27), but
the code was left in for future use.
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Acked-by: Stefano Babic <sbabic@denx.de>
When the data cache is enabled we must flush on write and invalidate
on read. We also check that buffers are aligned to data cache lines
boundaries. With recent work in U-Boot this should generally be the case
but the warnings will catch problems.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The pointer to the registers used to control the Freescale ESDHC MMC
controller is not initialized correctly when using PIO mode. This is
fixed by initializing the pointer in the same way as all other sites
within the driver.
Examining the commit history shows that this was broken at introduction
due to a code change in upstream U-Boot to support the mx51 processor
family.
Reported-by: Jim Lentz <JLentz@zhone.com>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
On Tegra2, card-detection is implemented by passing the card-detection
GPIOs to the MMC driver at initialization time. Instead of implementing
the board_mmc_getcd() function, use the card-detect hook and allow
boards to override it by providing their own board_mmc_getcd()
implementation.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
This card-detect hook probably doesn't work. Perhaps somebody with more
knowledge about the hardware can comment on this. I think that perhaps
even the complete code from esdhc_init() could go into the getcd()
function instead or mmc_getcd() needs to be called at some later time
after mmc_init(), which, however, would require many other drivers to
change.
In addition to implementing the hook, this patch also removes the call
to the board_mmc_getcd() function which is now called from the MMC
framework and is no longer required here.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Jason Liu <jason.hui@linaro.org>
Check for card detect each time an MMC/SD device is initialized. If card
detection is not implemented, this code behaves as before and continues
assuming a card is present. If no card is detected, has_init is reset
for the MMC/SD device (to force initialization next time) and an error
is returned.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Jason Liu <jason.hui@linaro.org>
The new API no longer uses the extra cd parameter that was used to store
the card presence state. Instead, this information is returned via the
function's return value. board_mmc_getcd() returns -1 to indicate that
no card-detection mechanism is implemented; 0 indicates that no card is
present and 1 is returned if it was detected that a card is present.
The rationale for this change can be found in the following email
thread:
http://lists.denx.de/pipermail/u-boot/2011-November/110180.html
In summary, the old API was not consistent with the rest of the MMC API
which always passes a struct mmc as the first parameter. Furthermore the
cd parameter was used to mean "card absence" in some implementations and
"card presence" in others.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Jason Liu <jason.hui@linaro.org>
Fix:
mv_sdhci.c: In function 'mv_sdh_init':
mv_sdhci.c:47:22: warning: the comparison will always
evaluate as 'true' for the address of 'mv_sdhci_writeb'
will never be NULL [-Waddress]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Andy Fleming <afleming@freescale.com>
Acked-by: Lei Wen <leiwen@marvell.com>
This patch improve the performance by spliting flag examination code
in ftsdc010_send_cmd() into 3 functions.
This patch also reordered the function which made better capability to
some high performance cards against to the next version of ftsdc010
hardware.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Add a host capability checking to avoid the mmc stack
switch the card to HIGHSPEED mode when the card supports
HIGHSPEED while the host doesn't.
This patch avoid furthur transaction problem when the
mmc/sd card runs different mode to the host.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
The mmc host controller on the i.mx6q is called usdhc which
is redesigned based on the freescale esdhc controller.
The usdhc controller is almost compatible with esdhc except
it adds one mix register to support debug/SD3.0 and move
the low bit 0-6 of XFERTYP register to the mix control reg
low bit 0-6. Thus on i.mx6q, we have the following compared
with the previous soc: (can refer to RM of chapter 56.3.3)
i.mx6q:
mix control:
bit 31 - bit 7: Added for debug/SD3.0 support
bit 6 - bit 0: move in the XFERTYP register bit 6-0 on previous soc
XFERTYP register:
bit 31 - bit 7: the same as before,
bit 6 - bit 0: no-use
previous soc
mix control: no
XFERTYP register:
bit 31 - bit 0: xfertype information
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
tegra2_mmc_init() is implemented by the Tegra2 MMC driver. Since most of
the Tegra2-based boards will need to call it, this commit exports it in
the new public asm/arch/mmc.h header file to prevent each board from
providing its own prototype.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
GPIO configuration shall never be done inside a driver, never.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Pass the GPIO numbers for power and card detect to tegra2_mmc_init(), and
modify that function to perform all required GPIO initialization. This
removes the need for board files to perform these operations.
Move board_mmc_getcd() into tegra2_mmc.c now that the driver knows which
GPIOs to use.
Update affected call-sites in seaboard.c and harmony.c. Note that this
change should make all SD ports work on Harmony, since the required GPIO
setup is now being performed.
v4: Fix prototype of tegra2_mmc_init() in board.h to match driver change.
Remove prototype of gpio_config_mmc() from board.h
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: Andy Fleming <afleming@gmail.com>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This reverts commit 02f3029f18.
This patch add 3 times retry to CMD8 because the Marvell mmc controller
doesn't obey the power ramp up process in the SD specification 6.4.1.
(Please refer to figure 6.1 and 6.2 in the specification.)
The CMD0 should be send after power ramp up has been finished.
However, the Marvell mmc contorller must do power ramp up after the
first CMD0 command has been send.
This patch also affect existing platforms like Nokia N900 and other
platforms.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Acked-by: Lei Wen <leiwen@marvell.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
sdhci_readw does not work for host version read in Armada100 series
SoCs. This patch fix this issue by making a sdhci_readl call to get host
version.
Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
Fix:
davinci_mmc.c: In function 'dmmc_wait_fifo_status':
davinci_mmc.c:72:7: warning: variable 'mmcstatus1' set but not used [-Wunused-but-set-variable]
davinci_mmc.c: In function 'dmmc_busy_wait':
davinci_mmc.c:89:7: warning: variable 'mmcstatus1' set but not used [-Wunused-but-set-variable]
Delete the unused variable.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
* 'master' of git://git.denx.de/u-boot-arm:
arm, davinci: add DAVINCI_MMC_CLKID
arm, davinci_emac: fix driver bug if more then 3 PHYs are detected
arm, davinci: da850/dm365 lowlevel cleanup
omap5: Add omap5_evm board build support.
omap4/5: Add support for booting with CH.
omap5: emif: Add emif/ddr configurations required for omap5 evm
omap5: clocks: Add clocks support for omap5 platform.
omap5: Add minimal support for omap5430.
omap: Checkpatch fixes
omap4: make omap4 code common for future reuse
GCC4.6: Squash warnings in onenand_base.c
GCC4.6: Fix common/usb.c on xscale
OneNAND: Add simple OneNAND SPL
PXA: vpac270: Enable the new generic MMC driver
PXA: Cleanup serial_pxa
PXA: Drop csb226 and innokom boards (unmaintained)
m28evk: Fix comment about the number of RAM banks
mx31: Fix checkpatch warnings in generic.c
mx31: Use proper IO accessor for GPR register
mx31: Remove duplicate definition for GPR register
qong: Use generic function for configuring GPR register
M28EVK: Enable USB HOST support
iMX28: Add USB HOST driver
iMX28: Add USB and USB PHY register definitions
M28: Add memory detection into SPL
iMX28: Fix ARM vector handling
M28: Add doc/README.m28 documentation
M28: Add MMC SPL
iMX28: Add support for DENX M28EVK board
iMX28: Add u-boot.sb target to Makefile
iMX28: Add image header generator tool
iMX28: Add driver for internal RTC
iMX28: Add GPMI NAND driver
iMX28: Add APBH DMA driver
iMX28: Add SPI driver
iMX28: Add GPIO control
iMX28: Add I2C bus driver
iMX28: Add PINMUX control
FEC: Add support for iMX28 quirks
iMX28: Add SSP MMC driver
iMX28: Initial support for iMX28 CPU
MX25: zmx25: GCC4.6 fix build warnings
da850: add new config file for AM18xx
BeagleBoard: config: Switch to ttyO2
OMAP3: Change omap3_evm maintainer
devkit8000: Fix NAND SPL on boards with 256MB NAND
integrator: enable Vpp and disable flash protection
integrator: add system controller header
integrator: make flash writeable on boot
integrator: use io-accessors for board init
integrator: move text offset to config
integrator: pass configs for core modules
ARM: remove superfluous setting of arch_number in board specific code.
SPL: Allow ARM926EJS to avoid compiling in the CPU support code
integrator: do not test first part of the memory
arm: a320: fix broken timer
ARM: define CONFIG_MACH_TYPE for all ronetix boards
dm646x: pass board revision info to kernel
dm646x: add new configuration for dm6467T
arm, davinci: Fix setting of the SDRAM configuration register
arm, davinci: Remove the duplication of LPSC functions
arm, davinci: Rename AM1808 lowlevel functions to DA850
da8xxevm: fix build error
ARM: re-add MACH_TYPE_XXXXXX for VCMA9 board and add CONFIG_MACH_TYPE
Fixing them here so that when the files are reused in
subsequent patches for omap5, avoids new checkpatch
warnings.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This is a well encapsulated section of mmc_send_cmd, by moving
it to it's own function it increases the readability of mmc_send_cmd.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Currently when no expected completion condition occures in the
mmc_send_cmd while loop that is waiting for a data transfer to
complete the MMC driver just hangs.
This patch adds an arbitrary 2 second timeout. If nothing we
recognize occures within 2 seconds some diagnostic information
is printed and we fail out.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Currently if a DMA buffer straddles a buffer alignment boundary
(512KiB) then the DMA engine will pause and generate a DMA
interrupt. Since the DMA interrupt is not enabled it will hang
the MMC driver.
This patch adds support for restarting the DMA transfer. The
SYSTEM_ADDRESS register contains the next address that would have
been read/written when a boundary is hit. So we can read that
and write it back. The write triggers the resumption of the
transfer.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
This moves the magic numbers sprinkled about the MMC driver
to a single location in the header file and gives them
meaningful names.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Acked-by: Andy Fleming <afleming@gmail.com>
The new IO FPGA implementation for Versatile Express contains an MMCI
(PL180) cell with the FIFO extended to 128 words. This causes the
read_bytes() function to go into an infinite loop; as it will wait for
for the half-full signal (SDI_STA_RXFIFOBR) if there are more than 8
words remaining (SDI_FIFO_BURST_SIZE), but it won't receive this signal
once there are fewer than 64 words left to transfer.
One possible fix is to add some build time configuration to change
SDI_FIFO_BURST_SIZE for the new implementation. However, the problematic
code only seems to exist as a small performance optimisation, so the
solution implemented by this patch is to simply remove it. The error
checking following the loop is also removed as this will be handled by
code further down the function.
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Jon Medhurst <jon.medhurst@linaro.org>
This centralizes knowledge of MMC clocking into the MMC driver. This also
removes clock setup from the board files, which will simplify later changes
that modify the Harmony board to support the correct set of MMC controllers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: Andy Fleming <afleming@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
SDHCI spec need to reset the sdma base address while the software
try to accorss the 512k bytes address boundary. When meet such
accross behavior, sdhci controller would generate a interrupt
automatically, and software need handle this.
Signed-off-by: Lei Wen <leiwen@marvell.com>
As per JEDEC document JESD84-A441 (page 105) response for CMD7
(MMC_CMD_SELECT_CARD) response should be R1 instead of R1b. In uboot we
never take MMC to disconnected state and on powerup its always ideal
state which later goes to stand-by state.
from document footnote:
R1 while selecting from Stand-By State to Transfer State; R1b while
selecting from Disconnected State to Programming State.
Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
For we don't know mmc bus width from reading registers, the only way
to check is to test.
Current compare offset is:
EXT_CSD_PARTITIONING_SUPPORT
EXT_CSD_ERASE_GROUP_DEF
EXT_CSD_REV
EXT_CSD_HC_ERASE_GRP_SIZE
EXT_CSD_SEC_CNT
Signed-off-by: Lei Wen <leiwen@marvell.com>
Previous magic number is hard to parse its meaning, change it to
respective macro definition
Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: WOlfgang Denk <wd@denx.de>
Marvell 88SV331xV5 platform's sdhci host control is not very standard
with the spec in the 8bit handling. It need to set its private register
to switch to the 8bit mode which is not included in the standard sdhci
registers.
This patch mainly hacks the writeb method, and set its private register
if it find the driver is going to switch to the 8bit mode.
Signed-off-by: Lei Wen <leiwen@marvell.com>
For some controller it has dynamic clock gating, and only toggle out clk
when the first cmd0 send out, while some card strictly obey the 74
clocks rule, the interval may not be sufficient between the cmd0 and
this cmd8, retry to fulfil the clock requirement.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
* 'master' of git://git.denx.de/u-boot-arm:
ARM: Add Calxeda Highbank platform
dkb: make mmc command as default enabled
Marvell: dkb: add mmc support
ARM: pantheon: add mmc definition
davinci: remove config.mk file from the sources
ARM:AM33XX: Add support for TI AM335X EVM
ARM:AM33XX: Added timer support
ARM:AM33XX: Add emif/ddr support
ARM:AM33XX: Add clock definitions
ARM:AM33XX: Added support for AM33xx
omap3/emif4: fix registers definition
davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUM
davinci: emac: add support for more than 1 PHYs
davinci: emac: add new features to autonegotiate for EMAC
da850evm: Move LPSC configuration to board_early_init_f()
omap4_panda: Build in cmd_gpio support on panda
omap: Don't use gpio_free to change direction to input
mmc: omap: Allow OMAP_HSMMC[23]_BASE to be unset
OMAP3: overo : Add environment variable optargs to bootargs
OMAP3: overo: Move ethernet CS4 configuration to execute based on board id
OMAP3: overo : Use ttyO2 instead of ttyS2.
da830: add support for NAND boot mode
dm36x: revert cache disable patch
dm644X: revert cache disable patch
devkit8000: Add malloc space
omap: spl: fix build break due to changes in FAT
OMAP3 SPL: Provide weak omap_rev_string
omap: beagle: Use ubifs instead of jffs2 for nand boot
omap: overo: Disable pull-ups on camera PCLK, HS and VS signals
omap: overo: Configure mux for gpio10
SPL: Add DMA library
omap3: Add interface for omap3 DMA
omap3: Add DMA register accessors
omap3: Add Base register for DMA
arm, davinci: add missing LSPC define for MMC/SD1
U-Boot/SPL: omap4: Make ddr pre-calculated timings as default.
DaVinci: correct MDSTAT.STATE mask
omap4: splitting padconfs into common, 4430 and 4460
omap4: adding revision detection for 4460 ES1.1
omap4: replacing OMAP4_CONTROL with OMAP4430_CONTROL
gplug: fixed build error as a result of code cleanup patch
kirkwood_spi: add dummy spi_init()
gpio: mvmfp: reduce include platform file
ARM: orion5x: reduce dependence of including platform file
serial: reduce include platform file for marvell chip
ARM: kirkwood: reduce dependence of including platform file
ARM: armada100: reduce dependence of including platform file
ARM: pantheon: reduce dependence of including platform file
Armada100: Add env storage support for Marvell gplugD
Armada100: Add SPI flash support for Marvell gplugD
Armada100: Add SPI support for Marvell gplugD
SPI: Add SPI driver support for Marvell Armada100
dreamplug: initial board support.
imx: fix coding style
misc: pmic: drop old Freescale's pmic driver
MX31: mx31pdk: use new pmic driver
MX31: mx31ads: use new pmic driver
MX31: mx31_litekit: use new pmic driver
MX5: mx53evk: use new pmic driver
MX5: mx51evk: use new pmic driver
MX35: mx35pdk: use new pmic driver
misc: pmic: addI2C support to pmic_fsl driver
misc: pmic: use I2C_SET_BUS in pmic I2C
MX5: efikamx/efikasb: use new pmic driver
MX3: qong: use new pmic driver
RTC: Switch mc13783 to generic pmic code
MX5: vision2: use new pmic driver
misc: pmic: Freescale PMIC switches to generic PMIC driver
misc:pmic:samsung Enable PMIC driver at GONI target
misc:pmic:max8998 MAX8998 support at a new PMIC driver.
misc:pmic:core New generic PMIC driver
mx31pdk: Remove unneeded config
mx31: provide readable WEIM CS accessor
MX51: vision2: Set global macros
I2C: Add i2c_get/set_speed() to mxc_i2c.c
ARM: Update mach-types
devkit8000: Add config to enable SPL MMC boot
devkit8000: protect board_mmc_init
arm, post: add missing post_time_ms for arm
cosmetic, post: Codingstyle cleanup
arm, logbuffer: make it compileclean
tegra2: Enable MMC for Seaboard
tegra2: Add more pinmux functions
tegra2: Rename PIN_ to PINGRP_
tegra2: Add more clock functions
tegra2: Clean up board code a little
tegra2: Rename CLOCK_PLL_ID to CLOCK_ID
pxa_mmc.c: In function 'mmc_cmd':
pxa_mmc.c:77:2: warning: format '%08x' expects type 'unsigned int', but argument
2 has type 'ulong'
pxa_mmc.c: In function 'mmc_block_read':
pxa_mmc.c:110:2: warning: format '%d' expects type 'int', but argument 4 has
type 'ulong'
pxa_mmc.c: In function 'pxa_mmc_write':
pxa_mmc.c:327:2: warning: format '%lx' expects type 'long unsigned int', but
argument 2 has type 'uchar *'
pxa_mmc.c:349:2: warning: format '%lx' expects type 'long unsigned int', but
argument 2 has type 'uchar *'
pxa_mmc.c:354:3: warning: format '%lx' expects type 'long unsigned int', but
argument 2 has type 'uchar *'
pxa_mmc.c:362:2: warning: format '%lx' expects type 'long unsigned int', but
argument 2 has type 'uchar *'
pxa_mmc.c:367:3: warning: format '%lx' expects type 'long unsigned int', but
argument 2 has type 'uchar *'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Not all omap families define OMAP_HSMMC[23]_BASE so condition those
cases in omap_mmc_init().
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This adds the required GPIO and pinmux configuration to make eMMC / SD work
on Seaboard.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Warren <twarren@nvidia.com>
This adds most of the clock functions required by board and driver code:
-query and adjust peripheral clocks
-query and adjust PLLs
-reset and enable control
These functions are plumbed in as required.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Warren <twarren@nvidia.com>
Currently the mmc_change_freq and mmc_startup functions allocates
buffers on the stack that are passed down to the MMC device driver.
These buffers could be unaligned to the L1 dcache line size. This
causes problems when using DMA and with caches enabled.
This patch correctly cache alignes the buffers used for reading the
ext_csd data from an MMC device.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Currently the sd_change_freq function allocates two buffers on the
stack that it passes down to the MMC device driver. These buffers
could be unaligned to the L1 dcache line size. This causes problems
when using DMA and with caches enabled.
This patch correctly cache alignes the buffers used for reading the
scr register and switch status values from an MMC device.
Change-Id: Ifa8414f572ef907681bd2d5ff3950285a215357d
Signed-off-by: Anton Staaf <robotboy@chromium.org>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Config VMMC voltage to 3V for MMC/SD card slot
and PBIAS settings needed for OMAP4
Fixes MMC/SD detection on boot from eMMC.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Enable high capacity to host capability.
Fixes eMMC detection on boot from MMC/SD card.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The mmc_send_status() function sets cmd.arg = 0. That's incorrect, so fix it.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Tested-by: Lei Wen <adrian.wenl@gmail.com>
Now that all platforms have been migrated to the new MMC driver, remove
the old one.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Currently if a DMA buffer straddles a buffer alignment boundary
(512KiB) then the DMA engine will pause and generate a DMA
interrupt. Since the DMA interrupt is not enabled it will hang
the MMC driver.
This patch adds support for restarting the DMA transfer. The
SYSTEM_ADDRESS register contains the next address that would have
been read/written when a boundary is hit. So we can read that
and write it back. The write triggers the resumption of the
transfer.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Tested-by : Jaehoon Chung <jh80.chung@samsung.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
This reverts commit c310fc8404.
The Atmel custodian had apparently rejected this patch's approach in
another thread, so this patch reverts it for now.
Signed-off-by: Andy Fleming <afleming@freescale.com>
If we don't want to build support for any partition types we can now
add #undef CONFIG_PARTITIONS in a board config file to keep this from
being compiled in. Otherwise boards assume this is compiled in by
default
Signed-off-by: Matthew McClintock <msm@freescale.com>
According to datasheet,set block count before multiple read/write.
Signed-off-by: elen.song <elen.song@atmel.com>
Acked-by: Andy Fleming <afleming@freescale.com>
This patch provides handling of the two way handshake when SEND_OP_COND
(CMD1) is send to mmc card. It is necessary to inform eMMC card if the
host can work with high capacity cards (Jedec JESD84-A441, point 7.4.3).
The extra flag MMC_MODE_HC (high capacity) is added to indicate if the
host is capable of handling the high capacity eMMC cards.
Since this change is added to the generic mmc framework, then it requires
other boards to indicate if their mmc controllers can handle high capacity
cards. As it is now - the old behaviour of the framework is preserved.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Some Renesas SuperH have MMCIF module. This driver supports it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Fix the problem that if we use the chip of MMC version 4 and
the capacity is smaller than 2GB or equal, the mmc->capacity is
invalid. According to the JEDEC Standard, the value of ext_csd's
capacity is valid if the value is more than 2GB.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Andy Fleming <afleming@freescale.com>
This could support both armada100 and pantheon serial in the mainline,
while this driver also be tested to support upcoming mg, mmp2 and mmp3
hardware.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Nowdays, there are plenty of mmc driver in uboot adopt the sd standard
host design, aka as sdhci. It is better to centralize the common logic
together to better maintenance.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Erase is a very basic function since the begin of sd specification is
announced. Although we could write a bulk of full 0xff memory to the
range to take place of erase, it is more convenient and safe to
implement the erase function itself.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This patch added set_mmc_clk for external clock control.
c210 didn't support host clock control.
So We need external_clock_control function for c210.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Fix typo resulting in the compilation error
s5p_mmc.c: In function 's5p_mmc_initialize':
s5p_mmc.c:469: error: 'struct mmc' has no member named 'm_bmax'
introduced by commit "MMC: make b_max unconditional"
(8feafcc49c)
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
CC: John Rigby <john.rigby@linaro.org>
CC: Andy Fleming <afleming@freescale.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add missing header file to fix compilation warning
omap_hsmmc.c: In function 'omap_mmc_init':
omap_hsmmc.c:474: warning: implicit declaration of function 'get_cpu_family'
omap_hsmmc.c:474: warning: implicit declaration of function 'get_cpu_rev'
introduced by commit "MMC: omap_hsmmc.c: disable
multiblock rw on old rev omap34xx silicon"
(4ca9244d74)
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
CC: Andy Fleming <afleming@freescale.com>
CC: John Rigby <john.rigby@linaro.org>
For emmc, it may have up to 7 partitions: two boot partitions, one
user partition, one RPMB partition and four general purpose partitions.
(Refer to JESD84-A44.pdf/page 154)
As bootloader may need to read out or reflashing images on those
different partitions, it is better to enable the partition switch with
console command support.
Also for partition would be restore to user partition(part 0) when CMD0
is used, so change mmc_init routine to perform normal initialization
only once for each slot, unless use the rescan command to force init
again.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
A "send status" command is added with the commit "mmc: checking
status after commands with R1b response". But the status register
returned from send status command of SPI protocol is different from
that of MMC/SD protocol. We do a simple test and generate a response
in stead of full bit-by-bit translation.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
For freescale i.MX53 eSDHCv2, when using CMD12, cmdtype need
to be set to ABORT, otherwise, next read command will hang.
This is a software Software Restrictions in i.MX53 reference manual:
29.7.8 Multi-block Read
For pre-defined multi-block read operation, that is,the number of blocks
to read has been defined by previous CMD23 for MMC, or pre-defined number
of blocks in CMD53 for SDIO/SDCombo,or whatever multi-block read without
abort command at card side, an abort command, either automatic or manual
CMD12/CMD52, is still required by ESDHC after the pre-defined number of
blocks are done, to drive the internal state machine to idle mode. In this
case, the card may not respond to this extra abort command and ESDHC will
get Response Timeout. It is recommended to manually send an abort command
with RSPTYP[1:0] both bits cleared.
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Make existing field b_max field in struct mmc unconditional
and use it instead of CONFIG_SYS_MMC_MAX_BLK_COUNT in mmc_bread
and mmc_bwrite.
Initialize b_max to CONFIG_SYS_MMC_MAX_BLK_COUNT in mmc_register
if it has not been initialized by the hw driver.
Initialize b_max to 0 in all callers to mmc_register.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add support for the ARM PrimeCell MultiMedia Interface - PL180.
Ported from original device driver written by ST-Ericsson.
Signed-off-by: Matt Waddel <matt.waddel@linaro.org>
Hi Terry,
> So I guess:
> mmc_init calls mmc_send_op_cond that set high_capacity,
> than it calls mmc_startup, that, with MMC_CMD_SEND_CSD command, set
> the capacity, using values in CSD register.
> So I guess that mmc_change_freq should not recalculate high_capacity.
>
> It seems better, isn't it?
>
> Regards,
> Raffaele
>
Finally I think that it is enough to apply the following patch in order
to fix the issue.
Regards,
Raffaele
Signed-off-by: Andy Fleming <afleming@freescale.com>
Defining CONFIG_MMC_TRACE in the include board file it is possible to activate
a tracing support.
This code helps in case of eMMC hw failure or to investigate possible eMMC
initialization issues.
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The first SEND_OP_COND (CMD1) command added is used to ask card capabilities.
After it an AND operation is done between card capabilities and host
capabilities (at the moment only for the voltage field).
Finally the correct value is sent to the MMC, waiting that the card
exits from busy state.
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: Andy Fleming <afleming@freescale.com>
It is recommended to check card status after these kind of commands.
This is done using CMD13 (SEND_STATUS) JEDEC command until
the card is ready.
In case of error the card status field is displayed.
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch supports mmc/sd card with spi interface. It is based on
the generic mmc framework. It works with SDHC and supports multi
blocks read/write.
The crc checksum on data packet is enabled with the def,
There is a subcomamnd "mmc_spi" to setup spi bus and cs at run time.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Andy Fleming <afleming@freescale.com>
These local vars need not be writable nor exported.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
As DATA_ERROR includes the value IRQSTAT_DTOE, a timeout error
would yield the first error return instead of TIMEOUT.
By swapping the test TIMEOUTs are reported as such
An alternate solution would be to remove the IRQSTAT_DTOE from the DATA_ERROR define
but as that one might be less desired I've opted for the simplest solution
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The maximum blocks value was hardcoded to 65535 due to a 16 bit
register length. The value can change for different platforms.
This patch makes the default the current value of 65535, but it
is configurable for other platforms.
Signed-off-by: Matt Waddel <matt.waddel@linaro.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
P1010 and P1014 has v2.3 version of FSL eSDHC controller in which watermark
level register description has been changed:
9-15 bits represent WR_WML[0:6], Max value = 128 represented by 0x00
25-31 bits represent RD_WML[0:6], Max value = 128 represented by 0x00
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Don't forget to count full data size for the multiblock operation request.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The timer register is 32bits, not 16bit, so 0xFFFF won't fill it.
Write out -1 to make sure to fill the whole thing.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Blocksize was hardcoded to 512 bytes. But the blocksize varies
depeding on various mmc subsystem commands (between 8 and 512).
This hardcoding was resulting in interrupt error during data
transfer.
It is now calculated based upon the request sent by mmc subsystem.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
- Timeout counter value is set as DTOCV bits in SYSCTL register
For counter value set as timeout,
Timeout period = (2^(timeout + 13)) SD Clock cycles
- As per 4.6.2.2 section of SD Card specification v2.00, host should
cofigure timeout period value to minimum 0.25 sec.
- Number of SD Clock cycles for 0.25sec should be minimum
(SD Clock/sec * 0.25 sec) SD Clock cycles
= (mmc->tran_speed * 1/4) SD Clock cycles
- Calculating timeout based on
(2^(timeout + 13)) >= mmc->tran_speed * 1/4
Taking log2 both the sides and rounding up to next power of 2
=> timeout + 13 = log2(mmc->tran_speed/4) + 1
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Data timeout counter (SYSCTL[DTOCV]) is not reliable for values of 4, 8,
and 12. Program one more than the desired value: 4 -> 5, 8 -> 9, 12 -> 13.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added support for MMC/SD cards for Davinci. This feature is enabled by
CONFIG_DAVINCI_MMC and is dependant on CONFIG_MMC and CONFIG_GENERIC_MMC
options. This is tested on DM355 and DM365 EVMs with both the available mmc
controllers.
Signed-off-by: Alagu Sankar <alagusankar@embwise.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The default value of the SRS, VS18 and VS30 and ADMAS fields in the host
controller capabilities register (HOSTCAPBLT) are incorrect. The default
of these bits should be zero instead of one.
Clear these bits out when we read HOSTCAPBLT.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Do not issue a manual asynchronous CMD12. Instead, use a (software)
synchronous CMD12 or AUTOCMD12 to abort data transfer.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some new platform's esdhc pins don't share with other function.
The eSDHC shouldn't be disabled, even if "esdhc" isn't defined
in hwconfig env variable.
Use CONFIG_FSL_ESDHC_PIN_MUX to fix this problem.
Signed-off-by: Chenhui Zhao <b26998@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The current code use all the voltage range support by the host
controller to do the validation. This will cause problem when
the host supports Low Voltage Range. Change the validation
voltage to be based on board setup.
Signed-off-by: Li Yang <leoli@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The max clock of MMC is 52MHz
Signed-off-by: Jerry Huang <Changm-Ming.Huang@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
After booting the u-boot, and first using some SD card (such as Sandisk 2G SD
card), because the field 'clock' of struct mmc is zero, this will cause
the read transfer is always active and SDHC DATA line is always active,
therefore, driver can't handle the next command.
Therefore, we use mmc_set_clock to setup both the data structure and HW
to the initial clock speed of 400000Hz.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
eSDHC host controller reset results in clearing of snoop bit also.
This patch sets the SNOOP bit after the completion of host controller reset.
Without this patch mmc reads are not consistent.
Signed-off-by: P.V.Suresh <pala@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Having a loop with a counter is no timing guarentee for timing
accuracy or compiler optimizations. For e.g. the same loop counter
which runs when the MPU is running at 600MHz will timeout in around
half the time when running at 1GHz. or the example where GCC 4.5
compiles with different optimization compared to GCC 4.4. use timer
to keep track of time elapse and we use an emperical number - 1sec
for a worst case timeout. This should never happen, and is adequate
imaginary condition for us to fail with timeout.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
This patch adds multi-block read support for the generic MMC
driver. Large reads are broken into chunks of 65535 blocks to
ensure that the code works with controllers having a 16 bit block counter.
This patch results in a significant performance improvement.
Time to read a 45 MB file went from 36 seconds to 9 seconds on Overo
Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Tested-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The current mmc write implementation is type ulong, but returns int values.
Some of the printf's are terminated with /n/r, one has none.
This patch fixes these issues and also removes some unnecessary local
variables.
Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Constraint the mmc framework to only send no more than 65535
blocks in one go during the multi-write command. This constraint
comes due to the limitation of 16bit width block counter register
at some hardware.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Cc: Reinhard Meyer <u-boot@emk-elektronik.de>
This Patch do support 8-bit bus width for s5p
So we add parameter for bus_width (in s5p_mmc_init(), s5p_mmc_initialize())
If want to use 8-bit bus width, only change (0, 8) instead of (0, 4).
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
OMAP boards currently use a legacy mmc driver. This patch adds a new
mmc driver which will work with the generic mmc driver in u-boot.
This new driver will work with both OMAP3 and OMAP4 boards.
This patch does not remove the old driver. It should remain in the
tree until all boards that use it switch to the new driver.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
The current mmc driver returns erroneous capacity information for
eMMC. The capacity of eMMC devices is available only in the ext-CSD
register. This patch add code to read the ext-CDSD register and
correctly calculate eMMC capacity.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Acked-by: Steve Sakoman <steve@sakoman.com>
Simplify the command setup and status checking steps, and add a proper
timeout to the status polling code to avoid possible infinite hangs.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Commit d2bf29e3 caused a number of compiler warnings:
mmc.c: In function 'mmc_bwrite':
mmc.c:97: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'long unsigned int'
mmc.c:97: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'lbaint_t'
mmc.c: In function 'mmc_bread':
mmc.c:229: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'long unsigned int'
mmc.c:229: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'lbaint_t'
Fix these.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Lei Wen <leiwen@marvell.com>
This patch is intended to prepare the other S5P SoC. (s5pc210)
If use SoC specific defines then can't share with other SoC.
So, make the accessor functions for access the base address by common way.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The OMAP3 block read function is not following API and always returning
1 instead of read block count, fix it. Also to simplify code, merge it
with with a helper function, which was only called from the block read
function.
After this patch ext2 filesystem can be used properly.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Make driver local variables and functions static and
remove them from the arch header.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds support mmc driver for s5p SoC
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
this eliminates compiler warnings when cmd_mmc.c is built with CONFIG_SYS_MMC_SET_DEV
the mmc_set_dev implementation in omap3_mmc.c is also tweaked to match
the new prototype in parameter naming and type
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The architecture independent header is moved to drivers/mmc, and the architecture
dependent headers reside in asm/arch-omap3 and asm/arch-omap4
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds support for the second and third mmc channels on OMAP3
processors
Boards wishing to use this feature should define CONFIG_SYS_MMC_SET_DEV
in the board config
Tested on Overo
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Tested-by: Philip Balister <philip@opensdr.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch enables PXAMCI support on PXA3xx CPUs. This patch only enables MMC1
though, MMC2 and PXA31x MMC3 will need further patch to be operational.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
In case the delays were set to 10000, the MMC card on PXA27X boards (and PXA3xx
boards) didn't initialize on first try. Increasing the delays and leaving just
those for PXA25x and 26x (that is 200000) fixes this problem.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Commit 77c1458d caused the following compiler warnings:
fsl_esdhc.c: In function 'esdhc_pio_read_write':
fsl_esdhc.c:142: warning: assignment discards qualifiers from pointer target type
fsl_esdhc.c: In function 'esdhc_setup_data':
fsl_esdhc.c:169: warning: unused variable 'wml_value'
fsl_esdhc.c: In function 'esdhc_pio_read_write':
fsl_esdhc.c:164: warning: control reaches end of non-void function
Fix these.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Dipen Dudhat <dipen.dudhat@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
On some Freescale SoC Internal DMA of eSDHC controller has bug.
So PIO Mode has been introduced to do data transfer using CPU.
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
When we set the read or write watermark in WML we should maintain the
rest of the register as is, rather than using some hard coded value.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
To support multiple block read command we must set abort or use auto
CMD12. If we booted from eSDHC controller neither of these are used
and thus we need to reset the controller to allow multiple block read
to function.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We need to stop the clocks on 83xx/85xx as well as imx. No need to make
this code conditional to just imx.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Stefano Babic <sbabic@denx.de>
Some registers of the mxcmmc driver were accessed using
16 bit accessor functions, because only the LSB is
significant. This is not needed and generates
warnings.
Signed-off-by: Stefano Babic <sbabic@denx.de>
There is be a path through mmc_read in drivers/mmc/mmc.c where
malloc'd memory is not freed before exiting mmc_read: it occurs if
mmc_set_blocklen() returns a non-zero value.
Reported-by: Quentin Armitage <Quentin@Armitage.org.uk>
Signed-off-by: Wolfgang Denk <wd@denx.de>
The esdhc controller in the mx51 processor is quite
the same as the one in some powerpc processors
(MPC83xx, MPC85xx). This patches adapts the driver
to support the arm mx51.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Most controllers can check if there is a card in the slot.
However, they require pins that could be not available because
required by other functions and the detection of a card must
be performed in another way. This patch adds a weak function
that a board can implement to add its internal custom way
to check the presence of a MMC/SD card.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Most cards do not answer if some reserved bits
in the ocr are set. However, some controllers
can set bit 7 (reserved for low voltages), but
how to manage low voltages SD card is not yet
specified.
Signed-off-by: Stefano Babic <sbabic@denx.de>
This is a port of Linux driver for SDHC host controller hardware
found on Freescale's MX2 and MX3 processors. Uses new generic MMC
framework (CONFIG_GENERIC_MMC) and it looks like there are some
problems with a framework (at least on LE cpus). Some of these
problems are addressed in the following patches.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Because twl4030 now has its own device files, move and rename
twl4030_mmc_config.
twl4030_mmc_config initializes the twl4030 power setting to
the mmc device. Because it is in the twl4030 power domain, move
it out of drivers/mmc/omap3_mmc.c and into drivers/power/twl4030.c.
The function was renamed to twl4030_power_mmc_init because all
the functions in this file are to have the format
twl4030_power_<device>_<action>
In this case the suffix is mmc_init so
device : mmc
action : init
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
We need to switch back to 1-bit before initialization or SD 2.0 cards
will fail to send SCR if we've switched to 4-bit already.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
This patch implements fdt_fixup_esdhc() function that is used to fixup
the device tree.
The function adds status = "disabled" propery if esdhc pins muxed away,
otherwise it fixups clock-frequency for esdhc nodes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
SCR & switch data are read from card as big-endian words and should be
converted to CPU byte order.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Cards which are not compatible with SD 2.0 standard, may return response
for CMD8 command, but it will be invalid in terms of SD 2.0. We should
accept this case as admissible, just like Linux does.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The mmc code defines the response as an array of chars. However, it
access the response bytes both as (i) an array of four uints (with
casts) and (ii) as individual chars. The former case is used more
often, including by the driver when it assigns the response.
The char-wise accesses are broken on little endian systems because they
assume that the bytes in the uints are in big endian byte order.
This patch fixes this by changing the response to be an array of four
uints and replacing the char-wise accesses with equivalent uint-wise
accesses.
Signed-off-by: Rabin Vincent <rabin@rab.in>
The generic MMC core uses direct long long divisions, which do not build
with ARM EABI toolchains. Use lldiv() instead, which works everywhere.
Signed-off-by: Rabin Vincent <rabin@rab.in>
find_mmc_device returns NULL if an invalid device number is specified.
Check for this to avoid dereferencing NULL pointers.
Signed-off-by: Rabin Vincent <rabin@rab.in>
__attribute__ follows gcc's documented syntax and is generally more
common than __attribute. This change is only asthetic and should not
affect functionality.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
The Blackfin SDH controller is still using the legacy framework, so update
the driver to use the renamed functions.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
These names are being taken over by the new MMC framework. Hopefuly
the PXA can be easily ported, and these functions will go away entirely.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
omap3_mmc.c was changed to define mmc_legacy_init.
Remove unused functions.
Compile tested on all arm
Runtime tested on Zoom1.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Here's a new framework (based roughly off the linux one) for managing
MMC controllers. It handles all of the standard SD/MMC transactions,
leaving the host drivers to implement only what is necessary to
deal with their specific hardware.
This also hooks the infrastructure into the PowerPC board code
(similar to how the ethernet infrastructure now hooks in)
Some of this code was contributed by Dave Liu <daveliu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This is a port of the Linux Blackfin on-chip SDH driver to U-Boot.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This makes it easier to use the driver on other platforms.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Jean-Chritophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
In order to consolidate more of the various MMC drivers around the
tree, we must first have a common place to put them.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Jean-Chritophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
