This node is required for NAND and NOR support. Node is taken from the
upstream Linux kernel DTS file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Import pq3-duart-0.dtsi device tree include file from upstream Linux kernel
for P2020. This allows U-Boot to use P2020 device tree files from upstream
Linux kernel which reference serial0 or serial1 devices.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
P2020 DTS files in upstream Linux kernel use fsl/p2020si-pre.dtsi and
fsl/p2020si-post.dtsi include device tree files.
Add symlinks for these include device tree files into U-Boot powerpc
directory and points them to U-Boot inline device tree files p2020.dtsi and
p2020-post.dtsi.
This allows to use P2020 DTS files from upstream Linux kernel in U-Boot.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The real entry point is _start_e500. There is no _start symbol at all. So
rename _start_e500 to _start for convension that _start symbol is used as
entry point.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
_start symbol contains only 32-bit data number 0x27051956 despite it is
marked as text section. This magic number is IH_MAGIC which is used for
marking uboot image header.
mpc85xx start.S code does not define valid uboot image header, so IH_MAGIC
number in _start symbol is useless there.
Moreover this _start symbol is not used at all. Entry point is at symbol
_start_e500.
So because this _start symbol is not used for anything, completely remove
it with IH_MAGIC number. After _start symbol was _start_cont symbol, so
replace all relative address calculations by _start_cont.
Signed-off-by: Pali Rohár <pali@kernel.org>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
removed sec_init() call from board files.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
device tree imported from linux kernel.
c500bee1c5b2 (tag: v5.14-rc4) Linux 5.14-rc4
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
As no platforms override this value, set it for all mpc83xx platforms.
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_MONITOR_BASE
Note that for how this is re-used on some PowePC platforms, we introduce
CONFIG_SPL_SYS_MONITOR_BASE and CONFIG_TPL_SYS_MONITOR_BASE and use the
CONFIG_VAL macro to get the correct value at build time, in the code.
Signed-off-by: Tom Rini <trini@konsulko.com>
The way board/keymile/Kconfig is written protects the options there from
being parsed on non-keymile platforms. We cannot however safely source
this file from multiple locations. This does not manifest as a problem
currently as there are no choice statements inside of this file (nor the
sub-Kconfig files it sources). However, moving some target selection to
one of these files exposes the underlying problem. Rework things so
that we have this file sourced in arch/Kconfig.
Cc: Holger Brunck <holger.brunck@hitachienergy.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Holger Brunck <holger.brunck@hitachienergy.com>
This converts removes the following symbols:
CONFIG_HAS_ETH0
CONFIG_HAS_ETH1
CONFIG_HAS_ETH2
CONFIG_HAS_ETH3
This is because at this point, only the ids8313 platform was using the
code which was controlled by these symbols. In turn, this code already
performs error checking on being able to perform the device tree fixup.
Rather than convert these to Kconfig for a single platform, update the
code to not need these checks and remove them from all the platforms
they were unused on.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove some code, primarily CPM2 related, that is now unused since the
removal of MPC8540/60ADS.
Fixes 3913191c8a ("powerpc: mpc8540ads: mpc8560ads: Drop support for MPC8540/60ADS")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There are no boards that define CONFIG_SYS_RESET_ADDRESS, so drop the
associated mpc8xx code that checks for it.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Christophe Leroy <christophe.leroy@csgroup.eu>
When building for a custom board, it is quite common to maintain a
private branch which include some defconfig and .dts files. But to
hook up those .dts files requires modifying a file "belonging" to
upstream U-Boot, the arch/*/dts/Makefile. Forward-porting that branch
to a newer upstream then often results in a conflict which, while it
is trivial to resolve by hand, makes it harder to have a CI do "try to
build our board against latest upstream".
The .config usually includes information on precisely what .dtb(s) are
needed, so to avoid having to modify the Makefile, simply add the
files in (SPL_)OF_LIST to dtb-y.
A technicality is that (SPL_)OF_LIST is not always defined, so rework
the Kconfig symbols so that (SPL_)OF_LIST is always defined (when
(SPL_)OF_CONTROL), but only prompted for in the cases which used to be
their "depends on".
nios2 and microblaze already have something like this in their
dts/Makefile, and the rationale in commit 41f59f6853 is similar to
the above. So this simply generalizes existing practice. Followup
patches could remove the logic in those two makefiles, just as there's
potential for moving some common boilerplate from all the
arch/*/dts/Makefile files to the new scripts/Makefile.dts.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
- fdt_support: Add fdt_for_each_node_by_compatible() helper macro
(Marek)
- turris_omnia: Fixup SATA or PCIe nodes at runtime in DT blob (Pali)
- pci_mvebu: Add support for Kirkwood PCIe controllers (Pali)
- SPL: More verifications for kwbimage in SPL (Pali)
- mvebu: Remove comphy_update_map() (Pali)
- Minor misc stuff
Add macro fdt_for_each_node_by_compatible() to allow iterating over
fdt nodes by compatible string.
Convert various usages of
off = fdt_node_offset_by_compatible(fdt, start, compat);
while (off > 0) {
code();
off = fdt_node_offset_by_compatible(fdt, off, compat);
}
and similar, to
fdt_for_each_node_by_compatible(off, fdt, start, compat)
code();
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
asm/mmu.h include is currently guarded by CONFIG_ADDR_MAP ifdef because
the header is only present on arm and powerpc. In order to remove the
dependency on this header and the associated ifdef, move init_addr_map()
declaration to init.h, since it is only called during the common init
sequence.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Add a return value to init_addr_map and use it directly in the
post-relocation init sequence, rather than using a wrapper stub.
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Commit 98f705c9ce ("powerpc: remove 4xx support") removed (in 2017) the
last code that made use of bedbug debugger support. Since there aren't
any boards left that define either CONFIG_CMD_BEDBUG or a real
bedbug_init(), drop this feature from u-boot.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In order to finish moving this symbol to Kconfig for all platforms, we
need to do a few more things. First, for all platforms that define this
to a function, introduce CONFIG_DYNAMIC_SYS_CLK_FREQ, similar to
CONFIG_DYNAMIC_DDR_CLK_FREQ and populate clock_legacy.h. This entails
also switching all users from CONFIG_SYS_CLK_FREQ to get_board_sys_clk()
and updating a few preprocessor tests.
With that done, all platforms that define a value here can be converted
to Kconfig, and a fall-back of zero is sufficiently safe to use (and
what is used today in cases where code may or may not have this
available). Make sure that code which calls this function includes
<clock_legacy.h> to get the prototype.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_IMMR
We do this by consolidating the SYS_IMMR options we have and providing
defaults.
We also, in the few places where M68K was also sharing code with these
platforms, define it within the file to CONFIG_SYS_MBAR to match usage.
This should be cleaned up longer term.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_FSL_IFC
This is done via select statements to match previous logic.
Signed-off-by: Tom Rini <trini@konsulko.com>
Use this new Kconfig instead of OF_BOARD, so we know for sure which boards
obtain their devicetree from a prior stage. Leave sandbox alone since it
does not. Also don't touch xilinx_versal_virt since it does not have a
specific TARGET Kconfig.
This option implies OF_BOARD for now, but with future work standard
passage may be used instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add rpi_4_32b and rpi_arm64 to the list of boards converted]
Signed-off-by: Tom Rini <trini@konsulko.com>
This uses QEMU virt which creates its own devicetree.
Add an empty version of this file, so that we can at least build this
board when devicetrees are required.
Signed-off-by: Simon Glass <sjg@chromium.org>
CONFIG_SYS_ATA_PORT_ADDR is not used in the code anymore. Drop it and use
ATA_PORT_ADDR() locally instead.
Drop CONFIG_IDE_RESET_ROUTINE and CONFIG_IDE_SWAP_IO which are also
unused.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_BR0_PRELIM
CONFIG_SYS_OR1_PRELIM
CONFIG_SYS_BR1_PRELIM
CONFIG_SYS_OR2_PRELIM
CONFIG_SYS_BR2_PRELIM
CONFIG_SYS_OR2_PRELIM
CONFIG_SYS_BR3_PRELIM
CONFIG_SYS_OR3_PRELIM
CONFIG_SYS_BR4_PRELIM
CONFIG_SYS_OR4_PRELIM
CONFIG_SYS_BR5_PRELIM
CONFIG_SYS_OR5_PRELIM
CONFIG_SYS_BR6_PRELIM
CONFIG_SYS_OR6_PRELIM
CONFIG_SYS_BR7_PRELIM
CONFIG_SYS_OR7_PRELIM
This also introduces CONFIG_SYS_BR0_PRELIM_BOOL as not all platforms
that can set these values do so. Add the relevant SYS_BRx_PRELIM_BOOL
to platforms that had not been previously migrated.
Signed-off-by: Tom Rini <trini@konsulko.com>
This has not been supported by toolchains for some time and has been
putting out a warning. Drop this.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This converts the following to Kconfig:
CONFIG_NAND_FSL_ELBC
CONFIG_NAND_FSL_IFC
Note that a number of PowerPC platforms had previously enabled
CONFIG_NAND_FSL_ELBC without CONFIG_MTD_RAW_NAND, and now they no longer
enable the option, reducing the size of a few functions.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Switch arc/arm/m68k/microblaze/mips/ppc arch_lmb_reserve() to
arch_lmb_reserve_generic().
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: Hai Pham <hai.pham.ud@renesas.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Wolfgang Denk <wd@denx.de>
As explained by Wolfgang, historically PowerPC would do a number of
things to hand-optimize placement of the binary on NOR flash in order to
maximize utilization of very scarce resources. These days, we simply
aren't optimizing our binary layout for NOR flash placement and it's
quite likely this wasn't working as intended. Furthermore, this level
of optimization makes it difficult to have version_string be a global,
instead of a weak and overridden value, and so make more progress on
reproducible builds, which is a current concern.
Move to having PowerPC no longer store version_string in the early part
of text so that it might be part of the first page of NOR and instead
use the same declaration everyone else does.
Link: https://lore.kernel.org/r/96716.1629798400@gemini.denx.de/
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline.
Remove it.
Note that we have to add CONFIG_SPIFLASH to scripts/config_whitelist.txt
because it's not really migrated at this point.
Acked-by: Michael Durrant <mdurrant@arcturusnetworks.com>
Acked-by: Oleksandr Zhadan <oleks@arcturusnetworks.com>
Acked-by: Oleksandr Zhadan and Michael Durrant <arcsupport@arcturusnetworks.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Handle CONFIG_SPIFLASH differently and delete Kconfig file]
Signed-off-by: Tom Rini <trini@konsulko.com>
We move the SYS_CACHE_SHIFT_N options from arch/arm/Kconfig to
arch/Kconfig, and introduce SYS_CACHE_SHIFT_4 to provide a size of 16.
Introduce select statements for other architectures based on current
usage. For MIPS, we take the existing arch-specific symbol and migrate
to the generic symbol. This lets us remove a little bit of otherwise
unused code.
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
Cc: Anup Patel <anup.patel@wdc.com>
Cc: Atish Patra <atish.patra@wdc.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Leo <ycliang@andestech.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
- Guard most of the options in drivers/ddr/fsl/Kconfig with
SYS_FSL_DDR || SYS_FSL_MMDC.
- Migrate FSL_DMA, DDR_ECC, DDR_ECC_CMD, and ECC_INIT_VIA_DDRCONTROLLER
to Kconfig.
- Clean up the logic for including the DDR_ECC_CMD code.
Signed-off-by: Tom Rini <trini@konsulko.com>
As this symbol can either be a fixed value or the function
get_board_ddr_clk, migration is tricky. Introduce a choice of DYNAMIC
or STATIC_DDR_CLK_FREQ. If DYNAMIC, we continue to use the board
defined get_board_ddr_clk function. If STATIC, set CONFIG_DDR_CLK_FREQ
to that value and now include/clock_legacy.h contains the function
prototype or defines get_board_ddr_clk() to that static value. Update
callers to test for DYNAMIC or STATIC.
Signed-off-by: Tom Rini <trini@konsulko.com>
These symbols are now either unused or were only used within the config
file to determine other logic, which could be done in a way that doesn't
further pollute the CONFIG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
It is a pain to have to specify the value 10 in each call. Add a new
dectoul() function and update the code to use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is a pain to have to specify the value 16 in each call. Add a new
hextoul() function and update the code to use it.
Add a proper comment to simple_strtoul() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the last
ARCH_T4160 platform, remove that support as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the last
ARCH_MPC8315 platform, remove that support as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. This is also the last
of the ARCH_MPC8641/MPC8610 platforms, so remove that support as well.
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them. As this includes
the last ARCH_MPC8572 platform, remove that as well.
Cc: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Peter Tyser <ptyser@xes-inc.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the last
ARCH_MPC8568 platform, remove that support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
the only ARCH_T1023 platform left, remove that support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them. As this is the only
ARCH_MPC8555 platform left, remove that support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the only
MPC8541 target left, remove that architecture support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it.
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline and are
also missing conversion to CONFIG_DM. Remove them.
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline.
Remove it.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Heiko Schocher <hs@denx.de>
This board has not been converted to CONFIG_DM_PCI by the deadline.
Remove it.
Cc: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI, CONFIG_DM_USB or
in some cases CONFIG_DM itself by the deadline. Remove them.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
With the changes in commit 588efcdd72fc ("powerpc: Don't use relative
include for config.h in global_data.h") fixing the root of the problem,
we no longer need this re-inclusion.
This reverts commit f6c0d365d3.
Cc: Matt Merhar <mattmerhar@protonmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
As there is an arch/powerpc/include/asm/config.h file using "" to get
config.h here can lead to using that rather than include/config.h. This
in turn can lead to a mismatch in the size of gd.
Cc: Matt Merhar <mattmerhar@protonmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Under DM, we rely on u-boot's device tree to provide the correct PHY
addresses. The board_fix_fdt callback is intended to be used for
device tree fixups before relocation. Unfortunately, this isn't an
option when booting from flash since the device tree isn't writable
before relocation.
This patch introduces the CONFIG_T2080RDB_REV_D option to signal that a
board revision D or up is the target. The config option is used to set
the correct Aquantia PHY address in the board's u-boot device tree.
Defconfig files with the option enable explicitly are added for
convenience.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The assembly output of the arch_initr_trap() function differed by a
single byte after common.h was removed from traps.c:
fff49a18 <arch_initr_trap>:
fff49a18: 94 21 ff f0 stwu r1,-16(r1)
fff49a1c: 7c 08 02 a6 mflr r0
fff49a20: 90 01 00 14 stw r0,20(r1)
-fff49a24: 80 62 00 44 lwz r3,68(r2)
+fff49a24: 80 62 00 38 lwz r3,56(r2)
fff49a28: 4b ff 76 19 bl fff41040 <trap_init>
fff49a2c: 80 01 00 14 lwz r0,20(r1)
fff49a30: 38 60 00 00 li r3,0
fff49a34: 38 21 00 10 addi r1,r1,16
fff49a38: 7c 08 03 a6 mtlr r0
This was causing a consistent hard lockup during the MMC read / loading
of the QoriQ FMan firmware on a P2041RDB board.
Re-adding the header causes identical assembly to be emitted and allows
the firmware loading and subsequent boot to succeed.
Fixes: 401d1c4f5d ("common: Drop asm/global_data.h from common header")
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
This commit does the same thing as Linux commit 33def8498fdd.
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There are a number of platforms that depend on a SATA driver that has
been converted to require AHCI but the platforms themselves are behind
on other migrations that would make it trivial to enable AHCI. Disable
SATA in these cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
When flush_cache() is called during boot on our ~7M kernel image, the
hundreds of thousands of WATCHDOG_RESET calls end up adding
significantly to boottime. Flushing a single cache line doesn't take
many microseconds, so doing these calls for every cache line is
complete overkill.
The generic watchdog_reset() provided by wdt-uclass.c actually
contains some rate-limiting logic that should in theory mitigate this,
but alas, that rate-limiting must be disabled on powerpc because of
its get_timer() implementation - get_timer() works just fine until
interrupts are disabled, but it just so happens that the "big"
flush_cache() call happens in the part of bootm where interrupts are
indeed disabled. [1] [2] [3]
I have checked with objdump that the generated code doesn't change
when this option is left at its default value of 0: gcc is smart
enough to see that the ">=" comparison is tautologically true, hence
all assignments to "flushed" are eliminated as dead stores.
On our board, setting the option to something like 65536 ends up
reducing total boottime by about 0.8 seconds.
[1] https://patchwork.ozlabs.org/project/uboot/patch/20200605111657.28773-1-rasmus.villemoes@prevas.dk/
[2] https://lists.denx.de/pipermail/u-boot/2021-April/446906.html
[3] https://lists.denx.de/pipermail/u-boot/2021-April/447280.html
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
CONFIG_5xx hasn't existed since commit 5025897774 (powerpc, 5xx:
remove support for 5xx). Remove this last mention of it.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Having WATCHDOG_RESET() called automatically from the timer interrupt
runs counter to the idea of a watchdog device - if the board runs into
an infinite loops with interrupts still enabled, the watchdog will
never fire.
When using CONFIG_(SPL_)WDT, the watchdog_reset function is a lot more
complicated than just poking a few SOC-specific registers - it
involves accessing all kinds of global data, and if the interrupt
happens at the wrong time (say, in the middle of an WATCHDOG_RESET()
call from ordinary code), that can end up corrupting said global data.
Allow the board to opt out of calling WATCHDOG_RESET() from the timer
interrupt handler by setting CONFIG_SYS_WATCHDOG_FREQ to 0 - as that
setting is currently nonsensical (it would be compile-time
divide-by-zero), it cannot affect any existing boards.
Add documentation for both the existing and extended meaning of
CONFIG_SYS_WATCHDOG_FREQ.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Add the FMan v3 nodes for the T1042D4RDB. The nodes are copied over with
little modification from the Linux kernel source code.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the QorIQ DPAA 1 FMan v3 device tree nodes for the T1042 SoC.
The device tree nodes are copied over with little modification
from the Linux kernel source code.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When two FMan's are present on a board, the MDIO nodes are found at the
same offsets inside each FMan. This causes "non unique device name"
errors when registering the MDIO nodes under the second FMan. Fix this
by updating the offsets of the MDIO nodes to include the parent FMan's
offset.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the FMan v3 nodes for the T4240RDB. The nodes are copied over with
little modification from the Linux kernel source code.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the QorIQ DPAA 1 FMan v3 device tree nodes for the T4240 SoC.
The device tree nodes are copied over with little modification
from the Linux kernel source code.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the FMan v3 nodes for the T2080RDB. The nodes are copied over with
little modification from the Linux kernel source code.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the QorIQ DPAA 1 FMan v3 device tree nodes for the T2080 SoC.
The device tree nodes are copied over with little modification from
the Linux kernel source code.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them. As the P5020 is the last ARCH_P5020 platform, remove that
support as well.
Cc: Andy Fleming <afleming@gmail.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
With the last of the ARCH_P1022 platforms removed, finish removing the
rest of the platform support.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them.
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC, along with other
DM conversions, by the deadline. Remove them.
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_MMC, along with other
DM conversions, by the deadline. Remove them.
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. It is also the only ARCH_T2081 board so remove that support
as well.
Cc: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Signed-off-by: Tom Rini <trini@konsulko.com>
The T2080RDB has a ds1339 on i2c0. Add this to the devicetree and enable
the relevant support in the configs.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
board/emulation is the place for other QEMU targets like x86, arm,
riscv. Let's move the qemu-ppce500 board codes there.
List me as a co-maintainer for this board.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
dev_read_addr_size_index() returns fdt_addr_t which might be a
64-bit physical address. This might be true for some 85xx SoCs
whose CCSBAR is mapped beyond 4 GiB.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Without this, the DM GPIO driver for MPC8xxx does not compile for
MPC85xx SoCs.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In phys_to_virt() and virt_to_phys(), if CONFIG_ADDR_MAP is defined,
they use addrmap_ translation APIs to do the address translation.
However these APIs only work in post-relocation phase.
Update the code logic to fall back to use the default one when in
pre-relocation phase.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
LAW related codes should be wrapped with CONFIG_FSL_LAW.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. As this is the last ARCH_MPC8569 board, remove that support
as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Use CONFIG_IS_ENABLED() macro, which provides more convenient
way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs
for both SPL and U-Boot proper.
CONFIG_IS_ENABLED(DM_I2C) expands to:
- 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y',
- 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y',
- 0 otherwise.
All occurences were replaced automatically using these bash cmds:
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Update gpio driver to use same logic for big-endian and little-endian
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Update data type of '1' to '1ull' in below assignment
size = 1ull << sizebit;
to fix incorrect assignment issue.
e.g: when sizebit was 31, 0x80000000 got sign extended to
0xffffffff_80000000
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reported-by: Dean Saridakis <dean.saridakis@baesystems.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Pulled in the kmcent2.dts and all its dependents from Linux 5.10,
commit 2c85ebc57b3e upstream. Replaced the license text with
SPDX License Identifiers.
Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
At present we have bdinfo_print_num() to print unsigned long numbers.
We also have print_phys_addr() which accept numbers that might be
64-bit on a 32-bit platform.
Rename these 2 functions to be clearer:
bdinfo_print_num() => bdinfo_print_num_l()
print_phys_addr() => bdinfo_print_num_ll()
While we are here, make bdinfo_print_num_ll() public so that it can
be used outside cmd/bdinfo.c in the future.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to remove the arch-specific ifdefs around initr_trap, introduce
arch_initr_trap weak initcall. Implementations for ppc/m68k/mips have
been moved to arch/<arch>/lib/traps.c
Default implementation is a nop stub.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add a return value to cpu_secondary_init_r and use it directly in the
post-relocation init sequence, rather than using a wrapper stub.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If the board isn't strapped to enable USB1 then attempting to access it
will result in a hang. Avoid this by allowing boards to define
CONFIG_USB_MAX_CONTROLLER_COUNT.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This uclass is intended to provide a way to obtain information about a
U-Boot board. But the concept of a U-Boot 'board' is the whole system,
not just one circuit board, meaning that 'board' is something of a
misnomer for this uclass.
In addition, the name 'board' is a bit overused in U-Boot and we want to
use the same uclass to provide SMBIOS information.
The obvious name is 'system' but that is so vague as to be meaningless.
Use 'sysinfo' instead, since this uclass is aimed at providing information
on the system.
Rename everything accordingly.
Note: Due to the patch delta caused by the symbol renames, this patch
shows some renamed files as being deleted in one place and created in
another.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
As the ownership is now Hitachi Power Grids, change the license string
and adapt the compatible string in DTS files. For kmeter1.dts we
change it to "keymile,KMETER1" for now, as this is then compliant with
what is submitted to the linux kernel. All other boards don't have
a upstreamed version in linux mainline.
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
CC: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
CC: Heiko Schocher <hs@denx.de>
CC: Marek Vasut <marex@denx.de>
CC: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The cpu_eth_init() is only used by the legacy ethernet driver framework.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
enable DTS support for keymile mpc83xx based boards.
get rid of compile warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Therefore done:
- add DTS for all mpc83xx based boards from keymile
mainly they are not mainlined to linux.
- add u-boot specific dtsi
- add stdout-path
- add missing ucc4 par_io definitions, which were
in board code, but not in linux DTS
- remove not used ethernet nodes
Signed-off-by: Heiko Schocher <hs@denx.de>
Patch-cc: Mario Six <mario.six@gdsys.cc>
Patch-cc: Qiang Zhao <qiang.zhao@nxp.com>
Series-to: u-boot
Series-version: 3
Series-changes: 3
- rebase patchset to current mainline commit
c0192950df
- update defconfig files
Series-changes: 2
- add patch which fixes Codingstyle errors in drivers/qe
- add patch which converts the mpc83xx based boards from
keymile to DM_ETH
Cover-letter:
powerpc, mpc83xx: add DM_ETH support
This patch series adds DM ethernet support for mpc83xx based
keymile boards.
Travis build:
END
add DM support for parallel I/O ports on QUICC Engine Block
Signed-off-by: Heiko Schocher <hs@denx.de>
Patch-cc: Mario Six <mario.six@gdsys.cc>
Patch-cc: Qiang Zhao <qiang.zhao@nxp.com>
Patch-cc: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Series-changes: 2
- remove RFC
- fixed Codingstyle errors, therefore new patch
powerpc, mpc83xx: fix codingstyle issues for qe_io.c
- moved DM part to drivers/pinctrl
Commit-notes:
Open questions / discussion:
- I let the old none DM based implementation in code
so boards should work with old implementation.
This should be removed if all boards are converted to
DM/DTS.
- Unfortunately linux DTS does not use "pinctrl-"
properties, instead "pio-handle" properties.
Even worser old U-Boot code initializes all pins
defined in "const qe_iop_conf_t qe_iop_conf_tab[]"
table in board code. As linux does the same I decided
to also scan through all subnodes containing "pio-map"
property and initialize them too.
The proper solution would be to check for "pio-handle"
when a device is probed.
END
With the planned removal of bi_memstart & bi_memsize, this patch now
moves the references to the better suiting gd->ram_base/ram_size
variables.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Factor out ppc-specific bdinfo setup from generic init sequence to
arch_setup_bdinfo in arch/powerpc/lib/bdinfo.c.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
bi_sramstart and bi_sramsize are generic members of the bd_info structure,
so move the m68k/powerpc-specific prints to generic code. Also, print them
only if SRAM support is enabled via CONFIG_SYS_HAS_SRAM.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Quite a few boards using this SoC family don't use binman, yet
CONFIG_BINMAN is enabled for all of them. But the option should only be
enabled if we expect binman to produce an image. Calling binman when the
device tree is missing, etc. will cause failer.
Add a condition so that CONFIG_BINMAN is only enabled as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The sdhc_adapter of global data has not been used, and we
do not have to use it as global data even we may need it
in the future.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:
It's a **mistake** to use typedef for structures and pointers.
Besides, using typedef for structures is annoying when you try to make
headers self-contained.
Let's say you have the following function declaration in a header:
void foo(bd_t *bd);
This is not self-contained since bd_t is not defined.
To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>
#include <asm/u-boot.h>
void foo(bd_t *bd);
Then, the include direcective pulls in more bloat needlessly.
If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:
struct bd_info;
void foo(struct bd_info *bd);
Right, typedef'ing bd_t is a mistake.
I used coccinelle to generate this commit.
The semantic patch that makes this change is as follows:
<smpl>
@@
typedef bd_t;
@@
-bd_t
+struct bd_info
</smpl>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
In order to support the compiler providing information used within
Kconfig itself we cannot have the compiler be determined by
arch/*/config.mk as we will not be able to evaluate that yet. Given
that most documentation tells people to specify CROSS_COMPILE, remove
these references.
Cc: Huan Wang <alison.wang@nxp.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Rick Chen <rick@andestech.com>
Cc: Thomas Chou <thomas@wytron.com.tw>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
We don't have an easy way to share these three lines of code with two
architectures. We also want to make it clear that this code is actually
arch-specific.
So just duplicate it in each arch-specific file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
We don't really want to have PPC-specific code in a generic file. Create
a new arch-specific function to hold it, and move it into that.
Make the function weak so that any arch can implement it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Xiaobo Xie <xiaobo.xie@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Poonam Aggrwal <poonam.aggrwal@nxp.com>
Patch-cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Timur Tabi <timur@tabi.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Po Liu <po.liu@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Naveen Burmi <naveen.burmi@nxp.com>
Patch-cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Poonam Aggrwal <poonam.aggrwal@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Ashish Kumar <ashish.kumar@nxp.com>
Patch-cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Introduce the QorIQ DPAA 1 Frame Manager nodes in the T1024RDB
device tree. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the QorIQ DPAA 1 Frame Manager v3 device tree nodes for the
T102x SoCs. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Introduce the QorIQ DPAA 1 Frame Manager nodes in the P5040DS
device tree. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Introduce the QorIQ DPAA 1 Frame Manager nodes in the P3041DS
device tree. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Introduce the QorIQ DPAA 1 Frame Manager nodes in the P2041RDB
device tree. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
