With the first redesign the debug UART had changed from
UART2 to UART1.
As the first hardware revision is considered as alpha and
will not be supported in future. The old setup will not
be preserved.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This update includes eqos support and some minor changes.
Synced with kernel commit
412627f6ffe3 ("arm64: dts: imx8mp-phyboard-pollux-rdk: Add missing pinctrl entry")
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Factor out the common node settings for dm-spl and dm-pre-reloc
and move them to imx8mp-u-boot.dtsi
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
If reset-gpio is defined by device-tree use that if
CONFIG_PCIE_IMX_PERST_GPIO is not defined.
Note that after this the following boards which define
CONFIG_PCIE_IMX_PERST_GPIO in their board header file as well as their
device-tree should be able to remove CONFIG_PCIE_IMX_PERST_GPIO without
consequence:
- mx6sabresd
- mx6sxsabresd
- novena
- tbs2910
- vining_2000
Note that the ge_bx50v3 board uses CONFIG_PCIE_IMX_PERST_GPIO and does
not have reset-gpios defined it it's pcie node in the dt thus removing
CONFIG_PCIE_IMX_PERST_GPIO globally can't be done until that board adds
reset-gpios.
Cc: Ian Ray <ian.ray@ge.com> (maintainer:GE BX50V3 BOARD)
Cc: Sebastian Reichel <sebastian.reichel@collabora.com> (maintainer:GE BX50V3 BOARD)
Cc: Fabio Estevam <festevam@gmail.com> (maintainer:MX6SABRESD BOARD)
Cc: Marek Vasut <marex@denx.de> (maintainer:NOVENA BOARD)
Cc: Soeren Moch <smoch@web.de> (maintainer:TBS2910 BOARD)
Cc: Silvio Fricke <open-source@softing.de> (maintainer:VINING_2000 BOARD)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Some IPs have their accessible address space restricted by the
interconnect. Let's make sure U-Boot only ever uses the space below
the 4G address boundary (which is 3GiB big), even when the effective
available memory is bigger.
We implement board_get_usable_ram_top() for all i.MX8M SoCs, as the
whole family is affected by this.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Aside from the usual fixes and updates one visible change is the
MMC update, which fixes some lingering bugs and gives a decent speed
increase on some boards (9->19 MB/s on H6, 21->43 MB/s on A64 eMMC).
I am keeping an watchful eye on bug reports here, to spot any correctness
regressions.
Another change is finally the enablement of the first USB host port on
many boards without micro-USB (data) sockets, like the Pine64 family.
That doubles the number of usable USB ports from 1 to 2 on those boards.
Some smaller fixes, 4GB DRAM support (on the H616) and a new board (ZeroPi)
conclude this first round of changes.
Compile-tested for all 157 sunxi boards, boot-tested on Pine H64,
Pine64-LTS, OrangePi Zero 2 and BananaPi M2 Berry.
Summary:
- DT update for H3/H5/H6
- Enable first USB port on boards without micro-USB
- ZeroPi board support
- 4GB DRAM support for H616 boards
- MMC fixes and speed improvement
- some fixes
To avoid the complexity of DMA operations (with chained descriptors), we
use repeated MMIO reads and writes to the SD_FIFO_REG, which allows us
to drain or fill the MMC data buffer FIFO very easily.
However those MMIO accesses are somewhat costly, so this limits our MMC
performance, to between 17 and 22 MB/s, but down to 9.5 MB/s on the H6
(partly due to the lower AHB1 frequency).
As it turns out we read the FIFO status register after *every* word we
read or write, which effectively doubles the number of MMIO accesses,
thus effectively more than halving our performance.
To avoid this overhead, we can make use of the FIFO level bits, which are
in the very same FIFO status registers.
So for a read request, we now can collect as many words as the FIFO
level originally indicated, and only then need to update the status
register.
We don't know for sure the size of the FIFO (and it seems to differ
across SoCs anyway), so writing is more fragile, which is why we still
use the old method for that. If we find a minimum FIFO size available on
all SoCs, we could use that, in a later optimisation.
This patch increases the eMMC read speed on a Pine64-LTS from about
22MB/s to 44 MB/s. SD card reads don't gain that much, but with 23 MB/s
we now reach the practical limit for 3.3V SD cards.
On the H6 we double our transfer speed, from 9.5 MB/s to 19.7 MB/s.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
All SoCs since the Allwinner A64 (H5, H6, R40, H616) feature the so
called "new timing mode", so enable this in Kconfig for those SoCs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Most Allwinner SoCs which use the so called "new timing mode" in their
MMC controllers actually use the double-rate PLL6/PERIPH0 clock as their
parent input clock. This is interestingly enough compensated by a hidden
"by 2" post-divider in the mod clock, so the divider and actual output
rate stay the same.
Even though for the H6 and H616 (but only for them!) we use the doubled
input clock for the divider computation, we never accounted for the
implicit post-divider, so the clock was only half the speed on those SoCs.
This didn't really matter so far, as our slow MMIO routine limits the
transfer speed anyway, but we will fix this soon.
Clean up the code around that selection, to always use the normal PLL6
(PERIPH0(1x)) clock as an input. As the rate and divider are the same,
that makes no difference.
Explain the hardware differences in a comment.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The H616 is our first supported Allwinner SoC which goes beyond the 4GB
address space "barrier", by having more than 32 address bits.
Lift the preliminary 3GB DRAM limit for the H616, and update the page
table setup on the way, to actually map that last GB as well.
As not all devices are actually capable of dealing with more than 32
bits (the DMA in the EMAC for instance), we also limit U-Boot's own
DRAM usage to 4GB on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
ZeroPi is a new board of high performance with low cost
designed by FriendlyElec., using the Allwinner H3 SOC.
ZeroPi features
- Allwinner H3, Quad-core Cortex-A7@1.2GHz
- 256MB/512MB DDR3 RAM
- microsd slot
- 10/100/1000Mbps Ethernet
- Debug Serial Port
- DC 5V/2A power-supply
Signed-off-by: Yu-Tung Chang <mtwget@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Most clock factors and dividers in the H6 PLLs use a "+1 encoding",
which we were missing on two occasions.
This fixes the MMC clock setup on the H6, which could be slightly off due
to the wrong parent frequency:
mmc 2 set mod-clk req 52000000 parent 1176000000 n 2 m 12 rate 49000000
Also the CPU frequency (PLL1) was a tad too high before.
For PLL5 (DRAM) we already accounted for this +1, but in the DRAM code
itself, not in the bit field macro. Move this there to be aligned with
what the other SoCs and other PLLs do.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Update the H3 DT files from the Linux 5.12 release.
The changes update some boards, and don't affect U-Boot, but fix Gigabit
Ethernet when this DT is passed on to the Linux kernel.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Update the H5 DT files from the Linux 5.12 release.
The changes don't affect U-Boot at all, but fix Gigabit Ethernet when
this DT is passed on to the Linux kernel. It also introduces DVFS.
This also updates the shared sunxi-h3-h5.dtsi, but that only adds nodes
that are of no concern to U-Boot.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Update the H6 DT files from the Linux 5.12 release.
The changes are minimal (many LED node renames), but also help to enable
USB port 0 in U-Boot (later), enable the RSB device (not yet used in
U-Boot), and also introduce an MMC frequency limit.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
As seen with clang-12:
warning: __asm_invalidate_l3_dcache changed binding to STB_WEAK
As we indeed use ENTRY and then declare the function weak manually. Use
the WEAK declarative from <linux/linkage.h> instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
On arm64, board info is not applicable and kernel command line patched into
the DT, so the LMB reservation here makes no sense anymore. On legacy arm32,
this might still be necessary on systems which do not use DT or use legacy
ATAGS. Disable this LMB reservation on arm64.
This also permits Linux DT to specify reserved memory node at address close
to the end of DRAM bank, i.e. overlaping with U-Boot location. Since after
boot, U-Boot will be no more, this is OK.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hai Pham <hai.pham.ud@renesas.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Rini <trini@konsulko.com>
Fix following compilation issue when SYS_DCACHE_OFF is enable:
drivers/misc/scmi_agent.c:128: undefined reference to `mmu_set_region_dcache_behaviour'
when SYS_DCACHE_OFF is enable, mmu_set_region_dcache_behaviour() must be
defined.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
On implementations that support VHE, the layout of the CPTR_EL2
register depends on whether HCR_EL2.E2H is set. If the bit is
set, CPTR_EL2 uses the same layout as CPACR_EL1 and can in fact
be accessed through that register. In that case, jump to the
EL1 code to enable access to the FP/SIMD registers. This allows
U-Boot to run on systems that pass control to U-Boot in EL2 with
EL2 Host mode enabled such as machines using Apple's M1 SoC.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Acked-by: Marc Zyngier <maz@kernel.org>
While this platform has not yet been converted, there is active efforts
to do so. Keep the platform for now.
This reverts commit aa697e6904.
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
the last of the SPEAr platforms, so remove the rest of the remaining
support as well.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
also the last SPEAR3XX platform, remove that symbol as well.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove it
Cc: Gerald Kerma <dreagle@doukki.net>
Cc: Tony Dinh <mibodhi@gmail.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove it
Cc: Ajay Bhargav <contact@8051projects.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove it.
This is also the last PL010_SERIAL using board, so remove those
references.
Cc: Sergey Kostanbaev <sergey.kostanbaev@fairwaves.ru>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them.
Cc: Andreas Bießmann <andreas@biessmann.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmDkSkAcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyD24B/9t87hFqWovJvVAcoUT
JoTqFblplE4Sckssy0cQyR7sRpzuZEaakUeAxaLFecBN6Tn30YJEG3hNpEDCLEbA
hn/oiZ4hQ3JA9Yu2SHepQi0fLqdAjkQtMXy57o3Mk20GBLtPtpdItUHxg3iyeMSj
Ny1mm/KjL6ltmNeGfYfeqRf435Rm718DB94wCZTgS9woYe3Z5YRDNBPyL7u27hpY
2WiyvvU9EA12mjGYdEt5sCqnTQZFtHHlEWNHz4a3db6HkcPV7pfr+SpTNJjcFhIg
O7VN7yUTwnV0UGu5IXTWcZqFIqJkLPbPX5cvkSBnnaGge4e0K3Cw36Nv/EqCY8LX
gWfu
=Ru8k
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2021.10-a' of https://source.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel fixes for 2021.10 cycle:
This small fixes set is dedicated to fixing the onewire subsystem for
the at91 boards which was broken since 2020.04.
- mpc8379erdb DM_USB, DM_PCI and DM_ETH support.
- Drop PCI support from the integrator family of boards
- Add synquacer support
- Assorted lpc32xx updates and improvements
- snapdragon (and related) fixes, Broadcom iproc update
It looks like SD card detection is broken at the moment for DB410c.
The eMMC is detected correctly, but the SD card is not.
This is probably similar to the issue fixed in commit 8505147403
("mmc: msm_sdhci: Use mmc_of_parse for setting host_caps") for eMMC,
except that the SD card does not have a property like "non-removable"
that skips the card detection.
The SDHCI on DB410c cannot detect itself if a SD card is inserted,
so add the necessary cd-gpios to make SD card detection work again.
While at it, fix the #gpio-cells for the soc_gpios to avoid DTC
warnings - the soc_gpios are actually already used with two cells
for the gpio-leds so this was just wrong all the time.
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The GICC register used by u-boot is 0x0a20c000, which is actually a GICC
for WCNSS, the WLAN processor. U-boot runs on the Application Processor,
therefore it should use APCS GICC instead. Hence, correct it with APCS GICC
register address.
Signed-off-by: Sheep Sun <sunxiaoyang2003@gmail.com>
Add basic support for running U-Boot on the Embedded Artists LPC3250
Developer's Kit v2 board by launching U-Boot from the board's s1l loader
(which comes pre-installed on the board).
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Import the dtsi, dts, and clock binding files for the lpc32xx ea3250 board
directly and unmodified from the latest Linux kernel.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
There's nothing special or unique to the lpc32xx that requires its own config
parameter for specifying the console uart index. Therefore instead of using
the lpc32xx-specific CONFIG_SYS_LPC32XX_UART include parameter, use the
already-available CONFIG_CONS_INDEX from Kconfig.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.
For more information, see this page;
https://www.96boards.org/product/developerbox/
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Add device trees for 96boards EE DeveloperBox and basement SynQuacer
SoC dtsi. These files are imported from EDK2
commit 83d38b0b4c0f240d4488c600bbe87cea391f3922
as-is (except for the changes #include path and some macros).
And add U-Boot specific changes in synquacer-sc2a11-developerbox-u-boot.dtsi
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Since some SoCs and boards do not hae extra asm/arch/gpio.h,
introduce CONFIG_GPIO_EXTRA_HEADER instead of adding
!define(CONFIG_ARCH_XXXX) in asm/gpio.h.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Add support for 1.3GHz, 1.35GHz and 1.4GHz parts. This is based on
equivalent code in Broadcom's LDK 5.0.6.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
The GPIO polarity for onewire must be GPIO_ACTIVE_HIGH.
On previous versions this used to work as it looks like the right flag values
are being passed since :
https://lists.denx.de/pipermail/u-boot/2020-April/407195.html
And that series broke the old functionality for onewire nodes.
Some boards had the correct value for the polarity, but it wasn't clear
so I replaced it with the right macro for the flag, instead of an empty value.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Now that u-boot gained DSA support, and it is already enabled for the
kontron_sl28 board, add the last missing piece and enable the
corresponding devices it in the device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
The enetc-2 port is used as DSA master (connected back-to-back to
mscc_felix_port4). Since the convention is to not enable ports in the
common SoC dtsi unless they are used on the board, then enable enetc-2
only when mscc_felix_port4 itself is enabled.
All existing device trees appear to adhere to this rule, so disable
enetc-2 in the SoC dtsi.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
To comply with the device tree bindings expectations for an Ethernet
controller, as well as to simplify the driver code, declare fixed-link
nodes for the internal ENETC ports (attached to the mscc_felix switch).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
There are no PCB trace delays on this board, so the PHY needs to enable
its internal ones in order to have a proper electrical connection to the
enetc MAC.
Fixes: b32e9a7578 ("arm: dts: ls1028a updates for network interfaces")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Due to an upstream change, the ls1028a.dtsi bindings for the mscc_felix
switch got accepted with all ports disabled by default and with no link
to the DSA master - this needs to be done on a per board basis.
Note that enetc-2 is not currently disabled in the ls1028a.dtsi, but
presumably at some point it might become. Explicitly enable it in the
QDS device trees anyway, to proactively avoid issues when that happens.
Fixes: a7fdac7e2a ("arm: dts: ls1028a: define QDS networking protocol combinations")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
clk:
- Add driver for Xilinx Clocking Wizard IP
fdt:
- Also record architecture in /fit-images
net:
- Fix plat/priv data handling in axi emac
- Add support for 10G/25G speeds
pca953x:
- Add missing dependency on i2c
serial:
- Fix dependencies for DEBUG uart for pl010/pl011
- Add setconfig option for cadence serial driver
watchdog:
- Add cadence wdt expire now function
zynq:
- Update DT bindings to reflect the latest state and descriptions
zynqmp:
- Update DT bindings to reflect the latest state and descriptions
- SPL: Add support for ECC DRAM initialization
- Fix R5 core 1 handling logic
- Enable firmware driver for mini configurations
- Enable secure boot, regulators, wdt
- Add support xck devices and 67dr
- Add psu init for sm/smk-k26 SOMs
- Add handling for MMC seq number via mmc_get_env_dev()
- Handle reserved memory locations
- Add support for u-boot.itb generation for secure OS
- Handle BL32 handoffs for secure OS
- Add support for 64bit addresses for u-boot.its generation
- Change eeprom handling via nvmem aliases
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYN105QAKCRDKSWXLKUoM
IZiFAJ9CIiEpHiBbnAhA0VOMGoaXHGULywCdED/5dNgVtc1C7y4avzETbEyWzD4=
=CdMa
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.10' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.10
clk:
- Add driver for Xilinx Clocking Wizard IP
fdt:
- Also record architecture in /fit-images
net:
- Fix plat/priv data handling in axi emac
- Add support for 10G/25G speeds
pca953x:
- Add missing dependency on i2c
serial:
- Fix dependencies for DEBUG uart for pl010/pl011
- Add setconfig option for cadence serial driver
watchdog:
- Add cadence wdt expire now function
zynq:
- Update DT bindings to reflect the latest state and descriptions
zynqmp:
- Update DT bindings to reflect the latest state and descriptions
- SPL: Add support for ECC DRAM initialization
- Fix R5 core 1 handling logic
- Enable firmware driver for mini configurations
- Enable secure boot, regulators, wdt
- Add support xck devices and 67dr
- Add psu init for sm/smk-k26 SOMs
- Add handling for MMC seq number via mmc_get_env_dev()
- Handle reserved memory locations
- Add support for u-boot.itb generation for secure OS
- Handle BL32 handoffs for secure OS
- Add support for 64bit addresses for u-boot.its generation
- Change eeprom handling via nvmem aliases
If both POSITION_INDEPENDENT and SYS_RELOC_GD_ENV_ADDR are enabled,
wherever original env is placed anywhere, it should be relocated to
the right address.
Relocation offset gd->reloc_off is calculated with SYS_TEXT_BASE in
setup_reloc() and env address gd->env_addr is relocated by the offset in
initr_reloc_global_data().
gd->env_addr
= (orig env) + gd->reloc_off
= (orig env) + (gd->relocaddr - SYS_TEXT_BASE)
However, SYS_TEXT_BASE isn't always runtime base address when
POSITION_INDEPENDENT is enabled. So the relocated env_addr might point to
wrong address. For example, if SYS_TEXT_BASE is zero, gd->env_addr is
out of memory location and memory exception will occur.
There is a difference between linked address such as SYS_TEXT_BASE and
runtime base address. In _main, the difference is calculated as
"run-vs-link" offset. The env_addr should also be added to the offset
to fix the address.
gd->env_addr
= (orig env) + ("run-vs-link" offset) + gd->reloc_off
= (orig env) + (SYS_TEXT_BASE - _start) + (gd->relocaddr - SYS_TEXT_BASE)
= (orig env) + (gd->relocaddr - _start)
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
This patch adds psgtr clocks and phy entry for USB0, USB1 and SATA node for
zc1751-xm017-dc3 board.
Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The board detection is incorrectly stating it's an rcar3 variant
instead of an RZ/G2 variant on all the r8a774*1_beacon boards.
Set the flag to correctly display as RZ/G2[M/N/H]
Signed-off-by: Adam Ford <aford173@gmail.com>
Enable basic PSCI support for R8A779A0 V3U Falcon
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Add board code for the R8A779A0 V3U Falcon board.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
--
Marek: - various small rebase fixes and clean ups
Add platform code to support R8A779A0 V3U SoC.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The R-Car V3U does support RPC interface, however the support for it is
missing in upstream Linux DTs as of commit 9f4ad9e425a1 ("Linux 5.12"),
add the node into u-boot.dtsi to let U-Boot access the SPI NOR or HF.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Add R8A779A0 V3U DT extras for U-Boot.
Based on "ARM: dts: renesas: Add R8A779A0 V3U DTs"
by Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
All symbols that are defined in Kconfig will always be defined (or not)
prior to preprocessing due to the -include directive while building.
However, symbols which are not yet migrated will only be defined (or
not) once the board config.h is included, via <config.h>. While the end
goal must be to migrate all symbols, today we have cases where the size
of gd will get mismatched within the build, based on include order.
Mitigate this by making sure that any <asm/global_data.h> that uses
symbols not in Kconfig does start with <config.h>. Remove this when not
needed.
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: Huan Wang <alison.wang@nxp.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Cc: Rick Chen <rick@andestech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
DT files have been added this year but forgot to update it that's why do it
in separate patch now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
It is not recommended to have aliases for gpio. In past it was used in
Linux for assigning numbers via sysfs which is deprecated and libgpiod
should be used instead.
In U-Boot this number is used for seq number but gpio offset are not
counted from this number. That's why having these aliases only for seq
number is not needed. As is done in Linux it is the best to use full gpio
name instead of sequence number which depends on sequence in binding.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Align USB nodes with the latest dt-bindings. It is adding resets, new
interrupt and also some quirks.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
dtc supports new sugar syntax which is easier compare to previous one
that's why also covert overlays for SOM to it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
kv260-revB is different compare to revA (usbhub is wired via i2c) that's
why remove revA compatible string.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Xilinx ZynqMP supports also addresses above 4GB (32bit) that's why also
generate u-boot.its with 64bit load/entry addresses to also support
different configurations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
psgtr node should be below pinctrl for easier comparion among dts files.
That's why move that nodes to different location.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Clock setting is not static anymore that's why it depends on firmware setup
that's why remove this comment.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Networking subsystem is not using aliases that's why remove them for CAN
devices. There is also no any other Xilinx ZynqMP DT file with them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
As per the design specification
"The 16-bit Seconds Calibration Value represents the number of
Oscillator Ticks that are required to measure the largest time
period that is less than or equal to 1 second.
For an oscillator that is 32.768 KHz, this value will be 0x7FFF."
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
psgtr node should be below pinctrl for easier comparion among dts files.
That's why move that nodes to different location.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Historically dpdma and dpsub are placed at the end of files. Move nodes
there for easier comparison among dts files.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
dwc3 can be used only for higher speeds than super-speed that's why
explicitly set it up.
This is also aligned with other ZynqMP dts files.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Uarts already have u-boot,dm-pre-reloc via zynqmp.dtsi that's why there is
no need to have them in platform DT files too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is need to pass entry about secure OS when bl32_entry is defined.
Currently only 64bit support is added but /fit-images node have been
extended to also record if this is 32bit or 64bit secure OS. When this is
tested the code will be update to support this configuration too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The first change is to trying to find out TF-A load address based on
reading elf file. Expectation is that bl31.bin is in the same folder as
bl31.elf. It brings new flexibility to place TF-A to any address (DDR
included).
And also enable TEE generation also with TEE configuration.
Expecation is the same as above that tee.bin and tee.elf are in the same
folder.
User has to just define link to BL31/BL32 binary files and the rest should
be handled by the script.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The SMMU is disabled in device tree so this change has no impact.
The benefit is that this way it is in sync with xen.dtsi. Xen enables
the SMMU and makes use of it.
Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
There is no reason to have CCI no enabled by default. Enable it when your
system configuration requires it. In Xilinx configuration flow this is
work for Device Tree Generator which reads information from HW Design
configuration.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Rename amba to AXI. Based on Xilinx Zynq TRM (Chapter 5) chip is "AXI
point-to-point channels for communicating addresses, data, and response
transactions between master and slave clients. This ARM AMBA 3.0..."
Issues are reported as:
.. amba: $nodename:0: 'amba' does not match
'^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
>From schema:
../github.com/devicetree-org/dt-schema/dtschema/schemas/simple-bus.yaml
Similar change has been done for Xilinx ZynqMP SoC.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/8a4bc80debfbb79c296e76fc1e4c173e62657286.1606397101.git.michal.simek@xilinx.com
From U-Boot, loading application on RPU core 0 is fine but loading on
core 1 is not handled properly. Lock-step mode needs both the R5 cores
to be initialized and it is working fine. Whereas in SPLIT mode individual
R5 cores needs to be initialized as they need to execute differenet
applications. Handle both these lock-step and split modes by propagating
mode and RPU core number(4 for RPU0 and 5 for RPU1) for various functions
and by adding conditions in those functions.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Linux commit f69629919942 ("dt-bindings: sram: Convert SRAM bindings to
json-schema") converted binding to yaml and some missing required
properties started to be reported. Align binding based on it.
The patch is fixing these warnings:
.../zynq-zc702.dt.yaml: sram@fffc0000: '#address-cells' is a required property
.../zynq-zc702.dt.yaml: sram@fffc0000: '#size-cells' is a required property
.../zynq-zc702.dt.yaml: sram@fffc0000: 'ranges' is a required property
>From schema: .../Documentation/devicetree/bindings/sram/sram.yaml
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/87c02786ccd8d7827827a9d95a8737bb300caeb0.1606397101.git.michal.simek@xilinx.com
The Linux commit f8f79fa6bb25 ("dt-bindings: at25: convert the binding
document to yaml") converted binding to yaml and 3 deprecated properties
pop up.
The patch is fixing these warnings:
.../zynq-zc770-xm013.dt.yaml: eeprom@2: 'pagesize' is a required property
.../zynq-zc770-xm013.dt.yaml: eeprom@2: 'size' is a required property
.../zynq-zc770-xm013.dt.yaml: eeprom@2: 'address-width' is a required property
>From schema: .../Documentation/devicetree/bindings/eeprom/at25.yaml
by converting them to new binding.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/be2c1125d98386033e182012eb08986924707a76.1606397101.git.michal.simek@xilinx.com
Use the ZDMA channel 0 to initialize the DRAM banks. This avoid
spurious ECC errors that can occur when accessing unitialized memory.
The feature is enabled by setting the option
CONFIG_SPL_ZYNQMP_DRAM_ECC_INIT and providing the following data:
SPL_ZYNQMP_DRAM_BANK1_BASE: start of memory to initialize
SPL_ZYNQMP_DRAM_BANK1_LEN : len of memory to initialize (hex)
SPL_ZYNQMP_DRAM_BANK2_BASE: start of memory to initialize
SPL_ZYNQMP_DRAM_BANK2_LEN : len of memory to initialize (hex)
Setting SPL_ZYNQMP_DRAM_BANK_LEN to 0 takes no action.
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove the LED unit addresses and reg properties to
fix the following dtc build warnings:
arch/arm/dts/o4-imx-nano.dtb: Warning (reg_format): /leds/led@0:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
...
arch/arm/dts/o4-imx-nano.dtb: Warning (avoid_default_addr_size): /leds/led@0: Relying on default #address-cells value
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Oleh Kravchenko <oleg@kaa.org.ua>
Linux uses the prefix "ethernet" whereas u-boot uses "eth". This is from
the linux tree:
$ grep "eth[0-9].*=.*&" arch/**/*dts{,i}|wc -l
0
$ grep "ethernet[0-9].*=.*&" arch/**/*dts{,i}|wc -l
633
In u-boot device trees both prefixes are used. Until recently the only
user of the ethernet alias was the sandbox test device tree. This
changed with commit fc054d563b ("net: Introduce DSA class for Ethernet
switches"). There, the MAC addresses are inherited based on the devices
sequence IDs which is in turn given by the device tree.
Before there are more users in u-boot and both worlds will differ even
more, rename the alias prefix to "ethernet" to match the linux ones.
Also adapt the test cases and rename any old aliases in the u-boot
device trees.
Cc: David Wu <david.wu@rock-chips.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move the message "Invalid or missing layout file."
to debug level as it is a normal behavior and not an error
and add the missing '\n'.
This patch avoids the strange trace :
Boot over usb0!
Invalid or missing layout file.DFU alt info setting: done
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Use get_cpu_dev() in uart getID command and remove the defines
DEVICE_ID_BYTE1 and 2 defines.
This patch prepare the support for new SOC family.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Correctly handle number of alternate when DM_PMIC is not activated.
This patch remove the last UNKNOWN partition in this case.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Handle the second USB enumeration only when the flashlayout is received
and when phase is PHASE_FLASHLAYOUT. This patch removes the call of
stm32prog_next_phase as it is already done in stm32prog_dfu_init().
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
When CONFIG_FIT_SIGNATURE is activated, CONFIG_LEGACY_IMAGE_FORMAT
is deactivated and the define IMAGE_FORMAT_LEGACY don't exist with
include/image.h:
#if defined(CONFIG_LEGACY_IMAGE_FORMAT)
#define IMAGE_FORMAT_LEGACY 0x01 /* legacy image_header based format */
#endif
This patch adds the needed check on compilation flag
CONFIG_LEGACY_IMAGE_FORMAT to avoid the compilation error
for command stm32prog:
cmd_stm32prog.c:81:8: error: ‘IMAGE_FORMAT_LEGACY’ undeclared
(first use in this function); did you mean ‘IMAGE_FORMAT_FIT’?
81 | if (IMAGE_FORMAT_LEGACY ==
| ^~~~~~~~~~~~~~~~~~~
| IMAGE_FORMAT_FIT
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the support in command stm32prog of kernel load and start
with initrd file, identify by the partition Type "Binary" in
the flashlayout.tsv, for example:
- 0x01 fsbl Binary none 0x0 tfa.stm32
- 0x03 fip Binary none 0x0 fip.bin
P 0x10 kernel System ram0 0xC2000000 uImage.bin
P 0x11 dtb FileSystem ram0 0xC4000000 board.dtb
P 0x12 initrd Binary ram0 0xC4400000 <initrd>
The <initrd> file can be a legacy image "uInitrd", generated
with mkimage, or a RAW initrd image "initrd.gz".
After a DFU detach the bootm command with be executed
with the associated address, for example:
$> bootm 0xC2000000 0xC4400000:<size> 0xC4000000
When the "Binary" partition type is absent, the 'bootm'
command starts the kernel without ramdisk, for example:
$> bootm 0xC2000000 - 0xC4000000
With this paths, it is no more mandatory to generate FIT
including the kernel, DT and initrd:
- 0x01 fsbl Binary none 0x0 tfa.stm32
- 0x03 fip Binary none 0x0 fip.bin
P 0x10 fit System ram0 0xC2000000 fit.bin
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Handle timeout in stm32prog_serial_get_buffer to sent NACK
to STM32CubeProgrammer when the buffer is not fully received.
This patch avoids to reach the STM32CubeProgrammer timeout and
the associated unrecoverable error.
Timeout error occurred while waiting for acknowledgment.
Error: Write Operation fails at packet number 4165 at address 0x1044FF
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This patch removes the header check for UART download;
the check of checksum is not mandatory with even parity and chuck
checksum for each 256 received bytes and it is only done for
STM32 image (FSBL = TF-A BL2), not for FIT image.
This patch solve issue of duplicated 0x100 byte written with FIP header.
Fixes: 4fb7b3e108 ("stm32mp: stm32prog: add FIP header support")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
RK3568 is a high-performance and low power quad-core application
processor designed for personal mobile internet device and AIoT
equipments.
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the SDMMC2 device tree node, as well as the pins it uses, in
U-Boot SPL.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Enable the SDMMC2 eMMC high-speed DDR mode as it is done in the
corresponding Linux kernel device tree.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Set the SDMMC2 VQMMC supply to vdd (buck3). Note that in the
corresponding Linux kernel device tree, the supply is set to v3v3
(buck4), which is wrong.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the “sdmmc2_d47_pins_d” pins to the SDMMC2 pinctrls. Increase the
bus width from four to eight.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The SDMMC2 interface hosts an eMMC. Replace the interface properties
that would only apply to SD cards—“broken-cd” and “disable-wp”—with
relevant ones: “non-removable”, “no-sd” and “no-sdio”.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmDLD78cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyLhSB/0UqOd+Ujf2meiHU9yr
oOOCLxVTjTUfIZKLad/zwlj2Xqzsjs6XMawC95BgouvkQLmj/gwerRWcZPg9l7/X
hvb9VJi+iJoLRRpBPbeF3bMb92kCE+YZodFXyutlcY+Z0ZB9755zoVgR6ccKfksd
Xp2y8AFptfYQNZ1l0yb3lhm1261CldWALrGTjRpY2hQ8nEMbV8z6WUB1hAF9CECa
PGbKaiqm9OdktwHsLy4cYFFCuzkykn6T3P6ODineP7IxgEgZKTfJClSTFGY9S0GQ
kwd7K/7j0W3rI5NPknB+Fb4IFAaTs/oozR+5ml7j+2S3G5GXjSGx8zaSOmOZvpP3
KxwN
=/I5V
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.10-a' of https://source.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for the 2021.10 cycle:
This feature set converts the boards pm9261 and pm9263 Ethernet support
to DM; enables hash command for all SAM boards; fixes the NAND pmecc
bit-flips correction; adds Falcon boot for sama5d3_xplained board; and
other minor adjustments.
Change the USB erratum number A-050106 to A-050204 as A-050106 is
a duplicate and never be published.
Fixes 0cfa00cdb9 (“armv8: Add workaround for USB erratum A-050106”)
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The EXPU1 design is a new 40G capable ethernet service unit card for
Hitachi-Powergrids wired-com product lines.
The base SoC is same as for already added SELI8 card, consequently the
already added u-boot support for SELI8 is reused.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
[Fixed new line error at EOF]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Address and size cells on SOC are set to 1. But gpio nodes are specified
with 2 cells. This fixes the gpio nodes to correct cells.
Signed-off-by: Lasse Klok Mikkelsen <lkmi@prevas.dk>
Reviewed-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Read Linux PPFE firmware from flash partition and pass it to Linux through
FDT entry. So that we can avoid placing PPFE firmware in Linux rootfs.
(FDT may increase at max by 64KB)
Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Signed-off-by: Anji J <anji.jagarlmudi@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
For cpu release command, check whether PSCI is supported firstly,
if supported, use PSCI to kick off secondary cores, otherwise still
use spin table.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
[Fixed checkpatch alignment CHECKs]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
It was noticed that the clock isn't continuously enabled when there is
no link. This is because the 125MHz clock is derived from the internal
PLL which seems to go into some kind of power-down mode every once in a
while. The LS1028A expects a contiuous clock. Thus enable the PLL all
the time.
Also, the RGMII pad voltage is wrong, it was configured to 2.5V (that is
the VDDH regulator). The correct voltage is 1.8V, i.e. the VDDIO
regulator.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
R5 SPL needs access to cfg space of Rings and UDMAP, therefore add RING
CFG, TCHAN CFG and RCHAN CFG address ranges.
Note that these registers are present within respective IPs but are
not populated in Linux DT nodes (as they are configured via TISCI APIs)
and hence are added to -u-boot.dtsi for now.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210607141753.28796-6-vigneshr@ti.com
MCU timer1 is used as the tick timer for MCU R5 SPL, and the
clock-frequency defined in DT appears to be incorrect at the moment.
Actual clock source for the timer is MCU_SYSCLK0 / 4 which is 250MHz.
Earlier setup of 25MHz went unnoticed, as there was a separate issue
with omap-timer, which caused an error to the clock by a factor of 8
with j7 devices. This problem surfaced once the omap-timer was fixed.
Signed-off-by: Tero Kristo <kristo@kernel.org>
Force the clk-k3 driver to probe early during R5 SPL boot to ensure the
default system clock configuration is completed. Many other drivers
assume a default state of the clock tree and it is currently possible
for them to probe before clk-k3 depending on the exact system
configuration.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Reported-by: Keerthy <j-keerthy@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Copy the contents of the board config loaded from sysfw.itb into an
EXTBOOT shared memory buffer that gets passed to sciserver. This only
needs to be done if EXTBOOT area has not been populated by ROM code yet.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Only start-up the non-linux remote cores if we are running in legacy
boot mode. HSM rearch is not yet supporting this.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
If the raw PM support is built in, we are operating in the split
firmware approach mode where PM support is not available. In this
case, skip the board config for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Add callback routines for parsing the firmware info from FIT image, and
use the data to boot up ATF and the MCU R5 firmware.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Add platform clock and powerdomain data for J721e and J7200. This data
is used by the corresponding drivers to register all the required device
clocks and powerdomains.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Add DM (device manager) firmware image to the fit image that is loaded by
R5 SPL. This is needed with the HSM rearch where the firmware allocation
has been changed slightly.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
board_fit_image_post_process() passes only start and size of the image,
but type of the image is not passed. So pass fit and node_offset, to
derive information about image to be processed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
On J7 family of SoCs (J721E and J7200), sysfw is being split to be run
under two cores, TIFS portion on DMSC core, and DM firmware under MCU
R5. As MCU R5 is also used to run one phase of the bootloader, we must
prevent access from here towards sysfw services. To support this, add
new config option which can be used to detect presence of RM/PM sysfw
services.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
The default register configuration after powerup for PSSYSMON_ANALOG_BUS
register is incorrect. Hence, fix this in SPL by writing correct fixed
value. It follows UG1085 chapter 'PS SYSMON Analog_Bus' and reflects commit
sw_apps:zynq ("056ca65d44549ce27f716d423e8dfdefeee7440c")
in Xilinx:embeddedsw[1].
[1] https://github.com/Xilinx/embeddedsw
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add nodes for SPI NOR partitions to the device tree of Turris MOX, as
are in Linux' device tree.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add nodes for indicator LED and reset button so that board code can
implement board factory reset mechanism.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
There have been some changes to the am335x-<board> DTs related to the
rtc node, so let's re-syncs them with Linux.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210602203805.11494-7-dariobin@libero.it
