Commit graph

638 commits

Author SHA1 Message Date
Alexey Brodkin
ca6d4d0f8f drivers/mmc/dw_mmc - remove extra arch specific "asm/arch/clk.h" inclusion
1. No contents of "asm/arch/clk.h" is used within "dw_mmc.c".
2. If arch doesn't have "asm/arch/clk.h" driver won't build.

Without mentioned inclusion dw_mmc driver could be built for arches
other than ARM. For ARM driver still builds without it.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Amar <amarendra.xt@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-07-16 18:44:22 -05:00
Haijun.Zhang
b8e5b07225 Powerpc: eSDHC: Fix mmc read write err in uboot of T4240QDS board
Fill the right command type when using CMD12 to stop data transfer.

Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
CC: Fleming Andrew-AFLEMING <AFLEMING@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-07-16 18:44:22 -05:00
Sascha Silbe
ff8fef5666 Fix block device accesses beyond 2TiB
With CONFIG_SYS_64BIT_LBA, lbaint_t gets defined as a 64-bit type,
which is required to represent block numbers for storage devices that
exceed 2TiB (the block size usually is 512B), e.g. recent hard drives.

For some obscure reason, the current U-Boot code uses lbaint_t for the
number of blocks to read (a rather optimistic estimation of how RAM
sizes will evolve), but not for the starting address. Trying to access
blocks beyond the 2TiB boundary will simply wrap around and read a
block within the 0..2TiB range.

We now use lbaint_t for block start addresses, too. This required
changes to all block drivers as the signature of block_read(),
block_write() and block_erase() in block_dev_desc_t changed.

Signed-off-by: Sascha Silbe <t-uboot@infra-silbe.de>
2013-06-26 10:26:06 -04:00
Tom Rini
348e47f766 Merge branch 'master' of git://git.denx.de/u-boot-arm 2013-06-22 07:38:12 -04:00
Albert ARIBAUD
69f14dc2fd Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'
Conflicts:
	spl/Makefile
2013-06-19 12:53:59 +02:00
Rajeshwari Shinde
ed7bdc03eb MMC: DWMMC: Fix FIFO_DEPTH calculation
Current DWMMC driver used to give FIFO underrun/overrun error every 3rd time
for mmc rescan command.
In current code FIFO_DEPTH is getting calculated after reading the default FIFOTH
register and extracting the RX_WMARK bits from it i.e (RX_WMARK = FIFO_DEPTH/2 -1).
Instead of storing the correct value, we were recalculating the FIFO_DEPT each
time which is not correct.

Based on "[PATCH V9 3/9] DWMMC: Initialise dwmci and resolve EMMC read write issues"
http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/160247

Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-17 11:03:42 +09:00
Tom Rini
dfdb3d37dd Merge branch 'master' of git://www.denx.de/git/u-boot-mmc 2013-06-14 16:06:49 -04:00
Stephen Warren
f866a46d6e mmc: report capacity for the selected partition
Enhance the MMC core to calculate the size of each MMC partition, and
update mmc->capacity whenever a partition is selected. This causes:

mmc dev 0 1 ; mmcinfo

... to report the size of the currently selected partition, rather than
always reporting the size of the user partition.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-13 16:52:19 -05:00
Andrew Gabbasov
01b77353e4 fsl_esdhc: Do not clear interrupt status bits until data processed
After waiting for the command completion event, the interrupt status
bits, that occured to be set by that time, are cleared by writing them
back. It is supposed, that it should be command related bits (command
complete and may be command errors).

However, in some cases the DMA already completes by that time before
the full transaction completes. The corresponding DINT bit gets set
and then cleared before even entering the loop, waiting for data part
completion. That waiting loop never gets this bit set, causing the
operation to hang. This is reported to happen, for example, for write
operation of 1 sector to upper area (block #7400000) of SanDisk Ultra II
8GB card.

The solution could be to explicitly clear only command related interrupt
status bits. However, since subsequent processing does not rely on
any command bits state, it could be easier just to remove clearing
of any bits at that point, leaving them all until all data processing
completes. After that the whole register will be cleared at once.

Also, on occasion, interrupts masking moved to before writing the command,
just for the case there should be no chance of interrupt between the first
command and interrupts masking.

Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-13 16:52:19 -05:00
Fabio Estevam
c2137b10a4 mmc: fsl_esdhc: Fix hang after 'save' command
Since commit 48e0b2bd (powerpc/esdhc: Correct judgement for DATA PIO mode)
we see mx6 systems to hang after doing a 'save' command.

Revert this commit since the original 'ifdef' logic from 7b43db92
(drivers/mmc/fsl_esdhc.c: fix compiler warnings) was the correct one.

Reported-by: Tapani Utriainen <tapani@technexion.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-13 16:52:19 -05:00
Ruud Commandeur
a586c0aa21 mmc write bug fix
This patch fixes a bug related to mmc writes.

When doing fatwrites on an SD-Card, MMC bus problems can occur. Depending
on the size of the file, "MMC0: Bus busy timeout!" is reported, resulting
in an SD-Card that is no longer responding.
It appears to be, that set_cluster can be called with a size being zero.
That can be with a file that has a size being an exact multiple
(including 0) of the clustersize, but also for files that are smaller than
the size of one cluster.
The same problem occurs if the "mmc write" command is given with a block
count being 0.

By adding a check for the block count being zero in mmc_write_blocks
(drivers/mmc.c), this problem is solved.

Signed-off-by: Ruud Commandeur <rcommandeur@clb.nl>
Cc: Tom Rini <trini@ti.com>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Mats Karrman <Mats.Karrman@tritech.se>
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-13 16:46:57 -05:00
Jagannadha Sutradharudu Teki
1695b29a5d mmc: sdhci: Enable 8-bit bus width only for 3.0 spec onwards
CAP register don't have any information for 8-bit buswidth support
on 2.0 sdhci spec, only from 3.0 onwards bit[18] got this information.

Due to this misassignment in sdhci, mmc is setting 8-bit buswidth using
mmc_set_bus_width even if controller doesn't support.
Below change has code information.
"mmc: Properly determine maximum supported bus width"
(sha1: 7798f6dbd5)

Bug log: <mmc plus and emmc cards)
-------
zynq-uboot> mmcinfo
Error detected in status(0x208100)!
Device: zynq_sdhci
Manufacturer ID: fe
.....

So enable 8-bit support only for 3.0 spec using CAP and for below 3.0
assign mmc->host_caps = MMC_MODE_8BIT on respective platform driver
if host have a support.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-13 16:44:49 -05:00
Amar
3690d6d66b MMC: APIs to support resize of EMMC boot partition
This patch adds APIs to access(open / close) and to resize boot partiton of EMMC.

Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-13 17:35:14 +09:00
Amar
a082a2dde0 EXYNOS5: DWMMC: Added FDT support for DWMMC
This patch adds FDT support for DWMMC, by reading the DWMMC node data
from the device tree and initialising DWMMC channels as per data
obtained from the node.

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-13 17:35:14 +09:00
Amar
9c50e35ff2 DWMMC: Initialise dwmci and resolve EMMC read write issues
This patch enumerates dwmci and set auto stop command during
dwmci initialisation.
EMMC read/write is not happening in current implementation
due to improper fifo size computation. Hence modified the fifo size
computation to resolve EMMC read write issues.

Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-13 17:35:13 +09:00
Balaji T K
a5d439c2d3 mmc: omap_hsmmc: Update pbias programming
Update pbias programming sequence for OMAP5 ES2.0/DRA7

Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:10 -04:00
Albert ARIBAUD
a19b0dd62d Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	common/cmd_fpga.c
	drivers/usb/host/ohci-at91.c
2013-05-30 14:45:06 +02:00
Haijun.Zhang
48e0b2bd2b powerpc/esdhc: Correct judgement for DATA PIO mode
The logic for the whether to configure for polling or DMA
was mistakenly reversed in this patch:

Commit 7b43db9211
drivers/mmc/fsl_esdhc.c: fix compiler warnings

Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
CC: Sun Yusong-R58495 <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-15 18:18:16 -05:00
Kuo-Jung Su
f6c3b34697 mmc: update Faraday FTSDC010 for rw performance
Faraday FTSDC010 is a MMC/SD host controller.
Although there is already a driver in current u-boot release,
which is modified from eSHDC and contributed by Andes Tech.
Its performance is too terrible on Faraday A36x SoC platforms,
so I turn to implement this new version of driver which is
10+ times faster than the old one.

It's carefully designed to be compatible with Andes chips,
so it should be safe to replace it.

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Andy Fleming <afleming@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-15 18:18:15 -05:00
Ying Zhang
ade8a1a6d3 drivers/mmc: move spl_mmc.c to common/spl
The mpc85xx repuires a special layout on the memory device that is
connected to the eSDHC controller interface. But the file spl_mmc.c
didn't handle this specfic case, there needs a special treatmen, in
the powerpc drictory. So, there is no longer to keep spl_mmc.c on
mpc85xx, CONFIG_SPL_FRAMEWORK is not set.

When CONFIG_SPL_MMC_SUPPORT is set and CONFIG_SPL_FRAMEWORK is not
set, there was an error in drivers/mmc/spl_mmc.c:

drivers/mmc/libmmc.o:(.got2+0x8): undefined reference to `spl_image'.

Now, the solution is to move the file "spl_mmc.c" to directory "common/spl".

Signed-off-by: Ying Zhang <b40530@freescale.com>
2013-05-15 08:41:03 -04:00
Bo Shen
93e3236ccb mmc: atmel_mci: add mmc card support
add mmc card support with atmel mci driver

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-05-12 16:48:11 +02:00
Bo Shen
aac4b69b2c mmc: atmel_mci: using IP version for different setting
Using IP version for different setting
  - Higher version supports 8bit mode
  - Higher version bus width setting is different

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-05-12 16:47:05 +02:00
Albert ARIBAUD
cac423a730 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2013-05-11 22:24:28 +02:00
Albert ARIBAUD
ec7023db8d Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'
Conflicts:
	drivers/mtd/nand/mxc_nand_spl.c
	include/configs/m28evk.h
2013-05-11 09:25:36 +02:00
Albert ARIBAUD
e825b100d2 Merge branch 'u-boot-pxa/master' into 'u-boot-arm/master' 2013-05-11 00:06:03 +02:00
Nishanth Menon
384bcae013 palmas: rename twl6035_mmc1_poweron_ldo with an palmas generic function
Since TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs,
rename twl6035_mmc1_poweron_ldo by a more generic palmas_mmc1_poweron_ldo
function.

Signed-off-by: Nishanth Menon <nm@ti.com>
2013-05-10 08:25:55 -04:00
Nishanth Menon
cb199102b0 twl6035: rename to palmas
TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs
Rename twl6035 to palmas to allow reuse across multiple current and
future platforms

As part of this change, change the CONFIG_TWL6035_POWER to
CONFIG_PALMAS_POWER and update usage of header file accordingly.

Signed-off-by: Nishanth Menon <nm@ti.com>
2013-05-10 08:25:54 -04:00
Fabio Estevam
88227a1d8a mmc: fsl_esdhc: Use calloc()
A malloc() followed by memset() can be simply replaced by calloc().

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-06 16:26:25 -05:00
Jaehoon Chung
a68aac4947 mmc: sdhci: return error when failed add_sdhci().
If failed the add_host(), it is reasonable that return value of
add_sdhci().

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-06 16:26:24 -05:00
Vipin Kumar
1f4ca2547c sdhci: Add sdhci support for spear devices
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-06 16:26:24 -05:00
Davide Bonfanti
3ba36d603a davinci, mmc: Added a delay reading ext CSD register
Without this additional delay, some eMMC don't negotiate properly bus width
Tested on:
 - Toshiba THGBM2G8D8FBAIB
 - Toshiba THGBM4G4D1HBAR
 - Micron MTFC4GMVEA (the one giving the problem)
 - Hynix H26M64002BNR
 - SanDisk SDIN5E1-32G

Signed-off-by: Davide Bonfanti <davide.bonfanti@bticino.it>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-06 16:26:24 -05:00
Che-Liang Chiou
e95504497e mmc: Split device init to decouple OCR-polling delay
Most of time that MMC driver spends on initializing a device is polling
OCR (operation conditions register).  To decouple this polling loop,
device init is split into two parts: The first part fires the OCR query
command, and the second part polls the result.  So the caller is now no
longer bound to the OCR-polling delay; he may fire the query, go
somewhere and then come back later for the result.

To use this, call mmc_set_preinit() on any device which needs this.

This can save significant amounts of time on boot (e.g. 200ms) by
hiding the MMC init time behind other init.

Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-06 16:12:38 -05:00
Egbert Eich
0472fbfd32 part/dev_desc: Add log2 of blocksize to block_dev_desc data struct
log2 of the device block size serves as the shift value used to calculate
the block number to read in file systems when implementing avaiable block
sizes.
It is needed quite often in file systems thus it is pre-calculated and
stored in the block device descriptor.

Signed-off-by: Egbert Eich <eich@suse.com>
2013-05-01 16:24:02 -04:00
Simon Glass
8bfa195e4e mmc: Define a constant for the maximum block size
The number 512 appears quite a bit in the mmc code. Add a constant for this
so that it can be used here and in other parts of the code (e.g. SPL code
which loads from mmc).

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@google.com>
2013-05-01 16:24:01 -04:00
Peter Korsgaard
2e222105c5 spl_mmc: cleanup variable types
block_read returns unsigned long, so it doesn't make sense to check for
< 0. and neither does marking the header structure as const and then
casting away the constness to load data into it.

Also cleanup some unneeded pointer casting while we're at it.

Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-05-01 16:24:00 -04:00
Michal Simek
293eb33fcb mmc: Add support for Xilinx Zynq sdhci controller
Add support for SD, MMC and eMMC card on Xilinx Zynq.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-04-30 11:39:27 +02:00
Stefan Roese
0499218dbc imx: Move some header files from arch-mxs to imx-common
The following headers are moved to a i.MX common location:

- regs-common.h
- regs-apbh.h
- regs-bch.h
- regs-gpmi.h
- dma.h

This way this header can be re-used also by other i.MX platforms.
For example the i.MX6 which will need it for the upcoming NAND
support.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2013-04-22 10:22:22 +02:00
Jaehoon Chung
1741c64d64 mmc: check the revision for sd3.0
Support to check whether the SD3.0 or not.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Rommel Custodio <sessyargc@gmail.com>
2013-04-17 10:58:51 -04:00
Jaehoon Chung
64f4a6192f mmc: support the correct card version for eMMC
eMMC vesrion is supported up to v4.5.
But bootloader isn't saw the exact eMMC version.
After applied this patch,
if use the mmcinfo command, then can see the exactly mmc version.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Rommel Custodio <sessyargc@gmail.com>
2013-04-17 10:58:51 -04:00
Albert ARIBAUD
345be0b267 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2013-04-14 11:45:06 +02:00
Andrew Gabbasov
9b74dc56fb fsl_esdhc: Fix DMA transfer completion waiting loop
Rework the waiting for transfer completion loop condition
to continue waiting until both Transfer Complete and DMA End
interrupts occur. Checking of DLA bit in Present State register
looks not needed in addition to interrupts status checking,
so it can be removed from the condition. Also, DMA Error
condition is added to the list of data errors, checked in the loop.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2013-04-14 11:22:47 +02:00
Eric Nelson
54899fc8fe fsl_esdhc: flush cache after IO completion
The cache should invalidate the read buffer for
the SD card interface after the transfer complete,
not command-complete.

Tested-by: Andrew Gabbasov <Andrew_Gabbasov@mentor.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2013-04-14 11:20:53 +02:00
Albert ARIBAUD
be08abc242 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2013-04-04 11:49:32 +02:00
Stephen Warren
5eaa215607 ARM: bcm2835: fix get_timer() to return ms
Apparently, CONFIG_SYS_HZ must be 1000. Change this, and fix the timer
driver to conform to this.

Have the timer implementation export a custom API get_timer_us() for use
by the BCM2835 MMC API, which needs us resolution for a HW workaround.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2013-04-04 08:14:54 +02:00
Abbas Raza
aad4659a2f mmc: i.MX6: fsl_esdhc: Define maximum bus width supported by a board
Maximum bus width supported by some i.MX6 boards is not 8bit like
others. In case where both host controller and card support 8bit transfers,
they agree to communicate on 8bit interface while some boards support only 4bit interface.
Due to this reason the mmc 8bit default mode fails on these boards. To rectify this,
define maximum bus width supported by these boards (4bit). If max_bus_width is not
defined, it is 0 by default and 8bit width support will be enabled in host
capabilities otherwise host capabilities are modified accordingly.

It is tested with a MMCplus card.

Signed-off-by: Abbas Raza <Abbas_Raza@mentor.com>
cc: stefano Babic <sbabic@denx.de>
cc: Andy Fleming <afleming@gmail.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2013-04-03 11:26:28 +02:00
Albert ARIBAUD
412665b461 Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master' 2013-03-26 09:51:09 +01:00
Peter Korsgaard
173ddc5b68 mmc: omap_hsmmc.c: only register getcd/getwp callbacks if gpio could be used
Gets rid of warnings from omap_gpio:
ERROR : check_gpio: invalid GPIO -1

(and undefined behaviour as the -1 error code is interpreted as gpio value)

Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
2013-03-24 12:49:12 -04:00
Peter Korsgaard
d4e1da4e09 mmc: mmc_getcd/getwp: use sensible defaults
Let mmc_getcd() return true and mmc_getwp() false if mmc driver doesn't
provide handlers for them.

Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
[trini: Add braces around first if test in each case to fix warning]
Signed-off-by: Tom Rini <trini@ti.com>
2013-03-24 12:49:12 -04:00
Stephen Warren
9a4fbe4fbd mmc: add bcm2835 driver
This adds a simple driver for the BCM2835's SD controller.

Workarounds are implemented for:
* Register writes can't be too close to each-other in time, or they will
  be lost.
* Register accesses must all be 32-bit, so implement custom accessors.

This code was extracted from:
git://github.com/gonzoua/u-boot-pi.git master
which was created by Oleksandr Tymoshenko.

Portions of the code there were obviously based on the Linux kernel at:
git://github.com/raspberrypi/linux.git rpi-3.6.y
commit f5b930b "Main bcm2708 linux port" signed-off-by Dom Cobley.

swarren changed the following for upstream:
* Removed hack udelay()s in bcm2835_sdhci_raw_writel(); setting
  SDHCI_QUIRK_WAIT_SEND_CMD appears to solve the issues.
* Remove register logging from read*/write* functions.
* Sort out confusion with min/max_freq values passed to add_sdhci().
* Use more descriptive variable names and calculations in IO accessors.
* Simplified and commented twoticks_delay calculation.
* checkpatch fixes.

Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Oleksandr Tymoshenko <gonzo@bluezbox.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Andy Fleming <afleming@gmail.com>
2013-03-20 15:31:25 +01:00
Albert ARIBAUD
b27673ccbd Merge branch 'u-boot-tegra/master' into 'u-boot-arm/master' 2013-03-15 20:50:43 +01:00
Albert ARIBAUD
6579d15c58 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2013-03-15 15:18:31 +01:00
Tom Warren
2d348a1652 mmc: Tegra: Add SD bus power/voltage function and MMC pad init call.
Tegra30 requires the SD Bus Voltage & Power bits be set in the SD
Power Control register. Tegra20 works w/o them set, but do it anyway
for those SoCs as it's part of the SD spec. Also call a common
board pad init routine (pad_init_mmc) in mmc_reset(), used by
Tegra30 only for now.

Note that Tegra20 SD/MMC HW differs enough from Tegra20 that a
new compatible entry is used in the fdt compat_names/id tables.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-14 11:06:44 -07:00
Tom Warren
c9aa831ee2 Tegra: MMC: Add DT support to MMC driver for all T20 boards
tegra_mmc_init() now parses the DT info for bus width, WP/CD GPIOs, etc.
Tested on Seaboard, fully functional.

Tamonten boards (medcom-wide, plutux, and tec) use a different/new
dtsi file w/common settings.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-14 11:06:42 -07:00
Łukasz Majewski
ce0c1bc135 mmc:sdhci:fix: Change default interrupts enabled at SDHCI initialization
This patch changes sdhci_init()'s behavior to NOT enable all interrupt
sources by default. Moreover interrupt signaling has been disabled.

This patch do not enable interrupts which aren't served in u-boot
(they are defined at sdhci.h but NOT used elsewhere):
- SDHCI_INT_CARD_INSERT, SDHCI_INT_CARD_REMOVE, SDHCI_BUS_POWER,
  SDHCI_INT_CARD_REMOVE, SDHCI_INT_CARD_INT

Special care shall be put on SDHCI_INT_CARD_INT, which indicates
interrupt generated by SD card.
According to "SD Host Controller Simplified Spec. ver 3.00" when bit 8
(Card Interrupt Status Enable) at "Normal Interrupt Status Enable
Register" (offset 0x34) is set, the card interrupt detection is started.
Then eMMC card may cause the SD controller to set this bit and then this
interrupt is passed to booted OS and might cause kernel crash.

To sum up:
- Only enable interrupts, which are served at u-boot
- This cleanup as a side effect fixes SDHCI's CARD INTERRUPT problem at
  Linux kernel (versions 3.6+, sdhci controller)
- Keep masked bits at "Normal Interrupt Signal Enable Register" (0x38h)

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Andy Fleming <afleming@freescale.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-03-12 19:50:49 +09:00
Tom Rini
76b40ab41e Merge u-boot/master into u-boot-ti/master
In master we had already taken a patch to fix the davinci GPIO code for
CONFIG_SOC_DM646X and in u-boot-ti we have additional patches to support
DA830 (which is CONFIG_SOC_DA8XX && !CONFIG_SOC_DA850).  Resolve these
conflicts manually and comment the #else/#endif lines for clarity.

Conflicts:
	arch/arm/include/asm/arch-davinci/gpio.h
	drivers/gpio/da8xx_gpio.c

Signed-off-by: Tom Rini <trini@ti.com>
2013-03-11 12:16:13 -04:00
Lokesh Vutla
c43c8339fe ARM: OMAP4+: Make control module register structure generic
A seperate omap_sys_ctrl_regs structure is defined for
omap4 & 5. If there is any change in control module for
any of the ES versions, a new structure needs to be created.
In order to remove this dependency, making the register
structure generic for all the omap4+ boards.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-11 11:06:10 -04:00
Nikita Kiryanov
e3913f56a2 omap_hsmmc: add driver check for write protection
Add check for write protection in omap mmc driver.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-08 16:41:13 -05:00
Nikita Kiryanov
d23d8d7e06 mmc: add support for write protection
Add generic mmc write protection functionality.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2013-03-08 16:41:13 -05:00
Nikita Kiryanov
e874d5b001 omap_hsmmc: implement driver check for card detection
Implement driver check for card detection.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2013-03-08 16:41:13 -05:00
Nikita Kiryanov
cc22b0c012 omap_hsmmc: introduce omap_hsmmc_data struct
Currently there's no appropriate place to store driver specific data
because the pointer that is meant for that (priv) is being used to
store the base address of mmc registers.

Introduce a new struct for storing driver specific data.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2013-03-08 16:41:13 -05:00
Nikita Kiryanov
5964dadd03 omap_hsmmc: fix out of bounds array access
There are 3 MMC/SD/SDIO controllers in OMAP SoCs, but only 2 structs
are defined for devices. This leads to data being written outside of
array bounds on systems that use all 3 controllers.

Update hsmmc_dev array to the correct size.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2013-03-08 16:41:12 -05:00
Marek Vasut
3430e0bd2a mxs: mmc: spi: dma: Better wrap the MXS differences
This patch streamlines the differences between the MX23 and MX28 by
implementing a few helper functions to handle different DMA channel
mapping, different clock domain for SSP block and fixes a few minor
bugs.

First of all, the DMA channel mapping is now fixed in dma.h by defining
the actual channel map for both MX23 and MX28. Thus, MX23 now does no
longer use MX28 channel map which was wrong. Also, there is a fix for
MX28 DMA channel map, where the last four channels were incorrect.

Next, because correct DMA channel map is in place, the mxs_dma_init_channel()
call now bases the channel ID starting from SSP port #0. This removes the
need for DMA channel offset being added and cleans up the code. For the
same reason, the SSP0 offset can now be used in mxs_dma_desc_append(), thus
no need to adjust dma channel number in the driver either.

Lastly, the SSP clock ID is now retrieved by calling mxs_ssp_clock_by_bus()
which handles the fact that MX23 has shared SSP clock for both ports, while
MX28 has per-port SSP clock.

Finally, the mxs_ssp_bus_id_valid() pulls out two implementations of the
same functionality from MMC and SPI driver into common code.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-03-07 17:22:56 +01:00
Sonic Zhang
187f32fac3 blackfin: bf60x: add rsi/sdh support
Add rsi/sdh support for bf60x.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Sonic Zhang <sonic.adi@gmail.com>
2013-03-04 13:42:07 +08:00
Tom Rini
951c6baaf4 Merge branch 'master' of git://git.denx.de/u-boot-arm 2013-02-12 10:18:31 -05:00
Simon Glass
e9adeca3fc ppc: arm: Move sdhc_clk into arch_global_data
This is used by both powerpc and arm, but I think it still qualifies as
architecture-specific.

Signed-off-by: Simon Glass <sjg@chromium.org>
2013-02-04 09:05:44 -05:00
Marek Vasut
e5b380ac68 mxs: mmc: Fix the MMC driver for MX23
The MX23 has different layout of DMA channels. Fix the MMC
driver to support MX23.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-28 11:43:01 +01:00
Marek Vasut
90bc2bf297 mxs: mmc: Allow overriding default card detect implementation
Some MXS based boards do not implement the card-detect signal. Allow
user to specify alternate card-detect implementation.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-28 11:43:01 +01:00
Otavio Salvador
8000d8a826 mxs: mmc: Fix MMC reset on iMX23
This does the same reset mask as done in v3.7 Linux kernel code.
The block is properly configured for MMC operation that way.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-28 11:43:01 +01:00
Marek Vasut
1a3c5ffe4f mmc: Limit the number of used SSP ports on MX23
The MX23 can only use two SSP ports.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-21 12:05:21 +01:00
Otavio Salvador
bf48fcb61b mxs: clock: Use 'mxs' prefix for methods
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-21 12:05:20 +01:00
Marek Vasut
14e26bcfa7 mxs: ssp: Pull out the SSP bus to regs conversion
Create function which converts SSP bus number to SSP register pointer.
This functionality is reimplemented multiple times in the code, thus
make one common implementation. Moreover, make it a switch(), since the
SSP ports are not mapped in such nice linear fashion on MX23, therefore
having it a switch will simplify things there.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-21 12:05:19 +01:00
Marek Vasut
59b6defa2b mxs: mmc: Drop unused members from struct mxsmmc_priv
The clock data are not used by the driver, drop them.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-21 12:05:19 +01:00
Albert ARIBAUD
7528cf5f01 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2013-01-08 14:59:37 +01:00
Shawn Guo
fb8302bfc5 fsl_esdhc: add MMC_MODE_HC host_caps
All esdhc variants we know should support high capacity MMC cards,
so let's add MMC_MODE_HC host_caps unconditionally to support those
MMC cards (capacity > 2 GB).

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-01-05 17:56:42 +01:00
Minkyu Kang
2c601c7208 Merge branch 'master' of git://git.denx.de/u-boot into resolve
Conflicts:
	README
	board/samsung/universal_c210/universal.c
	drivers/misc/Makefile
	drivers/power/power_fsl.c
	include/configs/mx35pdk.h
	include/configs/mx53loco.h
	include/configs/seaboard.h
2012-12-10 14:13:27 +09:00
Andy Fleming
7798f6dbd5 mmc: Properly determine maximum supported bus width
At some point, a confusion arose about the use of the bit
definitions in host_caps for bus widths, and the value
in ext_csd. By coincidence, a simple shift could convert
between one and the other:

MMC_MODE_1BIT = 0, EXT_CSD_BUS_WIDTH_1 = 0
MMC_MODE_4BIT = 0x100, EXT_CSD_BUS_WIDTH_4 = 1
MMC_MODE_8BIT = 0x200, EXT_CSD_BUS_WIDTH_8 = 2

However, as host_caps is a bitmask of supported things,
there is not, in fact, a one-to-one correspondence. host_caps
is capable of containing MODE_4BIT | MODE_8BIT, so nonsensical
things were happening where we would try to set the bus width
to 12.

The new code clarifies the very different namespaces:

host_caps/card_caps = bitmask (MMC_MODE_*)
ext CSD fields are just an index (EXT_CSD_BUS_WIDTH_*)
mmc->bus_width integer number of bits (1, 4, 8)

We create arrays to map between the namespaces, like in Linux.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
2012-11-27 17:48:46 -06:00
Stephen Warren
1981539914 mmc: tegra: use bounce buffer APIs
Tegra's MMC driver does DMA, and hence needs cache-aligned buffers. In
some cases (e.g. user load commands) this cannot be guaranteed by callers
of the MMC APIs. To solve this, modify the Tegra MMC driver to use the
new bounce_buffer_*() APIs.

Note: Ideally, all U-Boot code will always provide address- and size-
aligned buffers, so a bounce buffer will only ever be needed for user-
supplied buffers (e.g. load commands). Ensuring this removes the need
for performance-sucking bounce buffer cache management and memcpy()s.
The one known exception at present is the SCR buffer in sd_change_freq(),
which is only 8 bytes long. Solving this requires enhancing struct
mmc_data to know the difference between buffer size and transferred data
size, or forcing all callers of mmc_send_cmd() to have allocated buffers
using ALLOC_CACHE_ALIGN_BUFFER(), which while true in this case, is not
enforced in any way at present, and so cannot be assumed by the core MMC
code.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-11-27 17:26:49 -06:00
Stephen Warren
84d35b2863 common: rework bouncebuf implementation
The current bouncebuf API requires all parameters to be passed to both
bounce_buffer_start() and bounce_buffer_stop(). Modify the bouncebuf
start function to accept a state structure as a parameter, and only
require that state struct to be passed to the stop function. This
simplifies usage of the bounce buffer by clients.

Don't modify the data pointer, but rather store the temporary buffer in
this state struct. The bouncebuf code ensures that client code can
always use a single buffer pointer in the state structure, irrespective
of whether a bounce buffer actually had to be allocated.

Move cache management logic into the bounce buffer code, so that each
client doesn't have to duplicate this. I believe there's no need to
invalidate the buffer before a DMA operation, since flushing the cache
should prevent any write-backs.

Update the MXS MMC driver for this change.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-11-27 17:26:48 -06:00
Mela Custodio
688c2d140b mmc: add no simultaenous power and vdd
Bring in the code from Linux kernel.

Added to Linux kernel by:
commit e08c1694d9e2138204f2b79b73f0f159074ce2f5
Author: Andres Salomon <dilinger@queued.net>
Date:   Fri Jul 4 10:00:03 2008 -0700

Some HW balks when writing both voltage setting and power up at the same
time to SDHCI_POWER_CONTROL register.

Signed-off-by: Rommel G Custodio <sessyargc@gmail.com>
CC: Andy Fleming <afleming@freescale.com>

v2: fix attribution and SOB
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-11-27 17:26:48 -06:00
Taylor Hutt
babce5f64e mmc: Fix interpretation of MMC_CMD_ALL_SEND_CID
The interpretation of the data returned by the MMC_CMD_ALL_SEND_CID
command was incorrect with respect to the JEDEC Standard No. 84-A441.

This change makes the interpretation correct with respect to the
defined fields of the CID register.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Taylor Hutt <thutt@chromium.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-11-27 17:26:47 -06:00
Jaehoon Chung
d0ebbb8dfa EXYNOS: mmc: support DesignWare Controller for Samsung-SoC
Support DesignWare MMC Controller for Samsung Specific.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Rajeshawari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-11-27 17:26:47 -06:00
Stephen Warren
8c0ec0dbc4 mmc: tegra: support 4-bit operation too on 8-bit slots
If a board has all 8 data lines routed, the SD/MMC controller can still
operate in 4-bit (or presumably even 1-bit) mode. Adjust Tegra's MMC
driver to report the 4-bit capability even for 8-bit slots.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-11-19 08:15:41 -07:00
Tom Rini
6acc7c3cbc Merge branch 'master' of git://git.denx.de/u-boot-arm 2012-11-05 07:42:00 -07:00
Kim Phillips
eafa90a16c drivers/mmc/fsl_esdhc.c: sparse fixes
fsl_esdhc.c:71:6: warning: symbol 'esdhc_xfertyp' was not declared. Should it be static?
fsl_esdhc.c:413:6: warning: symbol 'set_sysctl' was not declared. Should it be st

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-11-04 11:00:37 -07:00
Kim Phillips
fdbb873eb0 drivers/mmc/mmc.c: sparse fixes
mmc.c:137:5: warning: symbol 'mmc_send_cmd' was not declared. Should it be static?
mmc.c:203:5: warning: symbol 'mmc_send_status' was not declared. Should it be static?
mmc.c:247:5: warning: symbol 'mmc_set_blocklen' was not declared. Should it be static?
mmc.c:440:5: warning: symbol 'mmc_read_blocks' was not declared. Should it be static?
mmc.c:510:5: warning: symbol 'mmc_go_idle' was not declared. Should it be static?
mmc.c:532:1: warning: symbol 'sd_send_op_cond' was not declared. Should it be static?
mmc.c:597:5: warning: symbol 'mmc_send_op_cond' was not declared. Should it be static?
mmc.c:661:5: warning: symbol 'mmc_send_ext_csd' was not declared. Should it be static?
mmc.c:683:5: warning: symbol 'mmc_switch' was not declared. Should it be static?
mmc.c:705:5: warning: symbol 'mmc_change_freq' was not declared. Should it be static?
mmc.c:775:5: warning: symbol 'sd_switch' was not declared. Should it be static?
mmc.c:796:5: warning: symbol 'sd_change_freq' was not declared. Should it be static?
mmc.c:935:6: warning: symbol 'mmc_set_ios' was not declared. Should it be static?
mmc.c:953:6: warning: symbol 'mmc_set_bus_width' was not declared. Should it be static?
mmc.c:1108:26: warning: dubious: !x & y
mmc.c:960:5: warning: symbol 'mmc_startup' was not declared. Should it be static?
mmc.c:1243:5: warning: symbol 'mmc_send_if_cond' was not declared. Should it be s

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-11-04 11:00:37 -07:00
Albert ARIBAUD
f04821a8ca Merge remote-tracking branch 'u-boot-imx/master' 2012-10-27 11:43:17 +02:00
Albert ARIBAUD
4c25761337 Merge remote-tracking branch 'u-boot-atmel/master' 2012-10-26 07:54:25 +02:00
Jaehoon Chung
757bff49ba mmc: dw-mmc: support DesignWare MMC Controller
Support the DesginWare MMC Controller.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Rajeshawari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 02:56:25 -05:00
Marek Vasut
48cf9dc63c mmc: pxa: Remove the old non-generic PXA MMC driver
This driver is no longer used and it's remaining users were converted
to the new generic PXA MMC driver. Thus, remove this driver.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 02:56:25 -05:00
Tushar Behera
13243f2eaf mmc: sdhci: Add a quirk to add delay during completion of sdhci_send_cmd
MMC host controller requires a delay between every sdhci_send_cmd()
execution. In s5p_mmc driver (s5p_sdhci replaces this driver), a delay
of 1000us was provided after every mmc_send_cmd() call. Adding a quirk
in current sdhci driver to replicate the behaviour.

Without this delay, MMC initialization on Origen board fails with
following error messages.

Timeout for status update!
mmc fail to send stop cmd

Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 02:53:36 -05:00
Jaehoon Chung
804c7f4221 mmc: sdhci: add the DMA select for SDMA
In host-control register, DMA select bit field is present.
BUt in sdhci.c, didn't select for DMA.
if set CONFIG_MMC_SDMA, we need to set SDMA-select bit.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 02:53:36 -05:00
Jaehoon Chung
5d48e42247 mmc: sdhci: increase the timeout value for data transfer
Timeout value is tunable.
When run read/write operation, sometime returned the timeout error.
Because the timeout value is too short.
So increased the enough timeout value.
(This timeout value is used to prevent the infinite loop.)

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 02:53:36 -05:00
Marek Vasut
d6b2e5085c mmc: Fix mmc_spi error on cmd->flags field
The recent removal of the cmd->flags field caused error in the
debuging code of mmc_spi. Fix this:

mmc_spi.c: In function 'mmc_spi_request':
mmc_spi.c:179:2: error: 'struct mmc_cmd' has no member named 'flags'

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 02:53:35 -05:00
Marek Vasut
49a627f8a1 MMC: Remove the MMC bounce buffer
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 02:53:35 -05:00
Marek Vasut
4e6d81d1a4 MMC: MXS: Convert MXS MMC driver to generic bounce buffer
Implement necessary code to use the generic bounce buffer routines
inside this driver. This replaces the MMC bounce buffer, which is
to be removed.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 02:53:35 -05:00
Wu, Josh
9924ca6e9b mmc: at91: use max timeout value. It will avoid some situation that timeout happened.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-10-17 11:29:52 +02:00
Wu, Josh
1db7377a70 mmc: at91: add multi block read/write support.
Since the at91sam9263, the mmc hardware support multi blocks read/write. So this driver enable it.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-10-17 11:28:54 +02:00
Benoît Thébaudeau
a2ac1b3a7d mxc: Fix SDHC multi-instance clock
On mxc, each SDHC instance has a dedicated clock, so gd->sdhc_clk is not
suitable for the multi-instance use case (initialization made directly with
fsl_esdhc_initialize()).

This patch fixes this issue by adding a configuration field for the SDHC input
clock frequency.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Jason Liu <r64343@freescale.com>
Cc: Matt Sealey <matt@genesi-usa.com>
Cc: Andy Fleming <afleming@gmail.com>
2012-10-16 12:35:10 +02:00
Tom Warren
150c24936b Tegra20: Move some include files to arch-tegra for sharing with Tegra30
The move is pretty straight-forward. ap20.h and tegra20.h were renamed to ap.h and tegra.h.
Some files remain in arch-tegra20 but 'include' a file in 'arch-tegra' with #defines & structs
that will be common between T20 and T30 HW. HW-specific #defines, etc. stay in the 'arch-tegra20'
'root' file.

All boards build OK w/MAKEALL -s tegra20. Checkpatch.pl runs clean. Seaboard works OK.

Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-10-15 11:54:06 -07:00
Tom Rini
3f7f2414ef ARM: SPL: Convert davinci to CONFIG_SPL_FRAMEWORK
- Convert the non-relocation part of board_init_f to spl_board_init, turn on CONFIG_SPL_BOARD_INIT in the configs.
- Remove duplicated code.
- Add spl_boot_device() that returns the statically chosen boot device.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 11:20:10 -07:00
Tom Rini
47f7bcae8c SPL: Move the omap SPL framework to common/spl
Add a new flag, CONFIG_SPL_FRAMEWORK to opt into the common/spl SPL
framework, enable on all of the previously using boards.  We move the
spl_ymodem.c portion to common/ and spl_mmc.c to drivers/mmc/.  We leave
the NAND one in-place as we plan to replace it later in this series.

We use common/spl to avoid linker problems with respect to merging
constant strings in objects.   Otherwise all strings in common/ will be
linked in and kept which grows SPL in size too much.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:49:59 -07:00
Tom Rini
495dbd72dd Merge branch 'master' of git://git.denx.de/u-boot-arm 2012-09-21 14:53:13 -07:00
Albert ARIBAUD
d193c1b6eb Merge remote-tracking branch 'u-boot-imx/master' 2012-09-21 00:26:19 +02:00
Tom Warren
29f3e3f248 Tegra: Change Tegra20 to Tegra in common code, prep for T30
Convert TEGRA20_ defines to either TEGRA_ or NV_PA_ where appropriate.
Convert tegra20_ source file and function names to tegra_, also.

Upcoming Tegra30 port will use common code/defines/names where possible.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
2012-09-10 13:01:24 -07:00
Stephen Warren
29159057a1 mmc: detect boot sectors using EXT_CSD_BOOT_MULT too
Some eMMC devices contain boot partitions, but do not set the PART_SUPPORT
bit in EXT_CSD_PARTITIONING_SUPPORT. Allow partition selection on such
devices, by enabling partition switching when EXT_CSD_BOOT_MULT is set.

Note that the Linux kernel enables access to boot partitions solely based
on the value of EXT_CSD_BOOT_MULT; EXT_CSD_PARTITIONING_SUPPORT only
influences access to "general" partitions.

eMMC devices affected by this issue exist on various NVIDIA Tegra
platforms (and presumably many others too), such as Harmony (plug-in eMMC),
Seaboard, Springbank, and Whistler (plug-in eMMC).

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-09-07 13:54:31 -07:00
Andy Fleming
95b01c47ed mmc: Remove incorrect cmd->flags usage
There were a couple of drivers that were actually using the flags
field of the cmd structure, despite the fact that no one ever
*set* that field. When we removed the field, those drivers failed
to compile. Replaced the references with the correct usage of
resp_type.

Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-09-06 15:23:13 -05:00
Marek Vasut
97ed12cedf MX28: MMC: Avoid DMA DCache race condition
This patch prevents dcache-related problem. The problem manifested
itself on the SPI driver, this is just a port to the MMC driver.

The scenario is the same. In case an "mmc read" is issued to a
buffer which was written right before it and data cache is enabled,
the cache eviction might happen during the DMA transfer into the
buffer, therefore corrupting the buffer. Clear any cache lines that
might contain the buffer to prevent such issue.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2012-09-06 14:17:55 +02:00
Jaehoon Chung
b09ed6e4fe mmc: s5p_sdhci: add the set_mmc_clk for cmu control
Samsung SoC use the cmu control to set clock.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-09-05 17:33:26 -05:00
Jaehoon Chung
8458e0283f mmc: s5p_sdhci: fixed wrong function argument
Useless code is removed, and get buswidth value.
buswidth value will be used to choice the 4bit or 8bit.
(Now used 4bit mode in sdhci.c by default)

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-09-05 17:33:26 -05:00
Jaehoon Chung
b268660ced mmc: s5p_sdhci: set the SDHCI_QUIRK_BROKEN_R1B
Samsung SoC is broken busy waiting for R1b type.
And clk delay control value is modified the previosuly value.
(that value used at the s5p_mmc.c)

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-09-05 17:33:26 -05:00
Joe Hershberger
470dcc7511 mmc: Add a SDHCI quirk for boards that have no CD
Some boards have no Card Detect wired.  In that case, set the CD test
bits in the standard interface.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-09-05 17:33:25 -05:00
Joe Hershberger
073cfd1c04 mmc: Fix version check for clock API in sdhci driver
When setting up the clocks in the sdhci driver, the "spec version"
must be masked off.  Otherwise any time the vendor version is not 0,
the check will allways assume the interface is version 3.  This breaks
when the interface is actually version 1 or 2.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-09-05 17:33:25 -05:00
Benoît Thébaudeau
6bb4b4bc35 mmc_get_dev: Return error if mmc_init fails
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-09-05 17:32:42 -05:00
Stephen Warren
8948ea8302 mmc: detect boot sectors using EXT_CSD_BOOT_MULT too
Some eMMC devices contain boot partitions, but do not set the PART_SUPPORT
bit in EXT_CSD_PARTITIONING_SUPPORT. Allow partition selection on such
devices, by enabling partition switching when EXT_CSD_BOOT_MULT is set.

Note that the Linux kernel enables access to boot partitions solely based
on the value of EXT_CSD_BOOT_MULT; EXT_CSD_PARTITIONING_SUPPORT only
influences access to "general" partitions.

eMMC devices affected by this issue exist on various NVIDIA Tegra
platforms (and presumably many others too), such as Harmony (plug-in eMMC),
Seaboard, Springbank, and Whistler (plug-in eMMC).

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-09-05 17:32:41 -05:00
Mikhail Kshevetskiy
122efd4389 MMC: u-boot-spl may be compiled without partition support
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-09-05 17:32:41 -05:00
Yoshihiro Shimoda
cdfd1ac6df mmc: fix capacity calculation when EXT_CSD_SEC_CNT is used
Since the type of "ext_csd" was array of char, the following
calculation might fail when the value of ext_csd[EXT_CSD_SEC_CNT]
was minus.

	capacity = ext_csd[EXT_CSD_SEC_CNT] << 0
			| ext_csd[EXT_CSD_SEC_CNT + 1] << 8
			| ext_csd[EXT_CSD_SEC_CNT + 2] << 16
			| ext_csd[EXT_CSD_SEC_CNT + 3] << 24;

So, this patch changes the type of "ext_csd" to array of u8.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-09-05 17:32:41 -05:00
Yoshihiro Shimoda
97a7b9928a mmc: sh_mmcif: enable MMC_MODE_HC
The controller can control high capacity cards. So, the patch adds
the flag. If the flag is not set, "mmcinfo" will fail when a high
capacity card is used.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-09-05 17:32:41 -05:00
Jongman Heo
5b0c942f89 mmc: fix wrong timeout check in mmc_send_status()
(!timeout) condition check in mmc_send_status() can never be met,
because do-while loop ends up with negative timeout value, -1.

Fix the check to handle TIMEOUT case correctly.

Signed-off-by: Jongman Heo <jongman.heo@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-09-05 17:32:41 -05:00
Kaspter Ju
67cbbf25c5 mmc: Remove unused item flags in struct mmc_cmd
Signed-off-by: Kaspter Ju <nigh0st3018@gmail.com>
2012-09-02 16:56:17 +02:00
Benoît Thébaudeau
16e43f354d fsl_esdhc: Remove cache snooping for i.MX
The cache snooping feature of Freescale's eSDHC IP is not available on i.MX, so
disable it globally for this architecture. This avoids setting no_snoop for all
i.MX boards, and it prevents setting a reserved bit of a reserved register if
fsl_esdhc_mmc_init() is used on i.MX, like in
arch/arm/cpu/armv7/imx-common/cpu.c/cpu_mmc_init().

Since no_snoop was only used on i.MX, get rid of it BTW.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
2012-09-01 14:58:30 +02:00
Otavio Salvador
fa7a51cb82 mxs: Convert sys_proto.h prefixes to 'mxs'
The sys_proto.h functions (except the boot modes) are compatible with
i.MX233 and i.MX28 so we use 'mxs' prefix for its methods.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2012-09-01 14:58:25 +02:00
Allen Martin
00a2749d7b tegra20: rename tegra2 -> tegra20
This is make naming consistent with the kernel and devicetree and in
preparation of pulling out the common tegra20 code.

Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-09-01 14:58:21 +02:00
John Rigby
10ed93dcdd u8500: Separating mmc config parameters from driver
Configuration in vexpress and u8500.v1 is different from what
is needed in u8500.v2.  As such, card configuration specifics need
to reside in the board file rather than the driver.

Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:20 +02:00
Marek Vasut
abb85be793 MX28: Fix MXS MMC DMA issues
The DMA didn't work properly because the DMA descriptor wasn't
properly cleaned after it was used once. Also, the DMA_ENABLE bit
was enabled/disabled too late.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
2012-09-01 14:58:17 +02:00
Marek Vasut
20255900b9 MX28: Transfer small blocks via PIO in MXS MMC
Large blocks (> 512b) shall be transfered via DMA to make
things a bit faster.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
2012-09-01 14:58:17 +02:00
Marek Vasut
869833285b MX28: Split out the PIO and DMA transfer functions
Move DMA and PIO data transfer parts into separate functions.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
2012-09-01 14:58:17 +02:00
Marek Vasut
401650a19c MX28: Fix up the MMC driver DMA mode
The DMA mode didn't properly configure the DMA_ENABLE bit in CTRL1.
Also, it was using SSP0 DMA channel for all SSP devices.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
2012-09-01 14:58:17 +02:00
Otavio Salvador
9c471142bc mxs: prefix register structs with 'mxs' prefix
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2012-09-01 14:58:17 +02:00
Lad, Prabhakar
0d986e61e2 da850/omap-l138: Add support to read u-boot image from MMC/SD
DA850/OMAP-L138 does not support strict MMC/SD boot mode. SPL will
be in SPI flash and U-Boot image will be in MMC/SD card. SPL will
do the low level initialization and then loads the u-boot image
from MMC/SD card.

Define CONFIG_SPL_MMC_LOAD macro in the DA850/OMAP-L138
configuration file to enable this feature.

Tested-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
2012-09-01 14:58:09 +02:00
Jerry Huang
975324a7d9 FSL/eSDHC: enable the clock to detect the SD card
For FSL low-end processors (VVN2.2), in order to detect the SD card,
we should enable PEREN, HCKEN and IPGEN to enable the clock.
Otherwise, after booting the u-boot, and then inserting the SD card,
the SD card can't be detected.
For SDHC VVN2.3 IP, these bits are reserved, and SDCLKEN is used.
And when accessing to these reserved bit, no any impact happened.

Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
CC: Andy Fleming <afleming@gmail.com>
CC: Marek Vasut <marex@denx.de>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-07-13 17:04:50 -05:00
Jerry Huang
d2d8afae33 SD/MMC: check the card status during erase operation
Use the function 'mmc_send_status' to check the card status.
only when the card is ready, driver can send the next erase command
to the card, otherwise, the erase will failed:
=> mmc erase 0 1
MMC erase: dev # 0, block # 0, count 1 ... 1 blocks erase: OK
=> mmc erase 0 2
MMC erase: dev # 0, block # 0, count 2 ... mmc erase failed
1 blocks erase: ERROR
=> mmc erase 0 4
MMC erase: dev # 0, block # 0, count 4 ... mmc erase failed
1 blocks erase: ERROR

Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
CC: Andy Fleming <afleming@gmail.com>
CC: Marek Vasut <marex@denx.de>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-07-13 17:04:50 -05:00
Łukasz Majewski
40242bc394 mmc:fix Call mmc_init() when executing mmc_get_dev()
This code adds call to mmc_init(), for partition related commands (e.g.
fatls, fatinfo etc.).

It is safe to call mmc_init() multiple times since mmc->has_init flag
prevents from multiple initialization.

The FAT related code calls get_dev high level method and then uses
elements from mmc->block_dev, which is uninitialized until the mmc_init
(and thereof mmc_startup) is called.

This problem appears on boards, which don't use mmc as the default
place for envs

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-07-13 17:04:50 -05:00
Jaehoon Chung
ad5fd92289 mmc: remove the hard setting for tran_speed
mmc_set_clock is set to the hard-coding.
But i think good that use the tran_speed value.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-07-13 17:04:49 -05:00
Eric Nelson
e576bd90f9 i.MX: fsl_esdhc: allow use with cache enabled.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-07-13 16:20:57 -05:00
Tom Warren
3f82d89d3d mmc: tegra2: rename tegra2_mmc.* to tegra_mmc.*
In anticipation of Tegra3 support, continue removing/renaming
Tegra2-specific files. No functional changes (yet).
Updated copyrights to 2012.

Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07 14:07:20 +02:00
Wolfgang Denk
ee3a55fdf0 Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm: (167 commits)
  OMAP4/5: Change omap4_sdp, omap4_panda, omap5_evm maintainer
  ARM: omap3: Add CONFIG_SPL_BOARD_INIT for CONFIG_SPL_MMC_SUPPORT
  ARM: omap3: Set SPL stack size to 8KB, image to 54KB.
  arm, omap3: fix warm reset serial output on OMAP36xx/AM/DM37xx
  OMAP4: Set fdt_high for OMAP4 devices to enable booting with Device Tree
  omap4: do not enable auxiliary cores
  omap4: do not enable fs-usb module
  omap4: panda: disable uart2 pads during boot
  igep00x0: change mpurate from 500 to auto
  igep00x0: enable the use of a plain text file
  tegra2: trivially enable 13 mhz crystal frequency
  tegra: Enable keyboard for Seaboard
  tegra: Switch on console mux and use environment for console
  tegra: Add tegra keyboard driver
  tegra: fdt: Add keyboard definitions for Seaboard
  tegra: fdt: Add keyboard controller definition
  tegra: Add keyboard support to funcmux
  input: Add support for keyboard matrix decoding from an fdt
  input: Add generic keyboard input handler
  input: Add linux/input.h for key code support
  fdt: Add fdtdec functions to read byte array
  tegra: Enable LP0 on Seaboard
  tegra: fdt: Add EMC data for Tegra2 Seaboard
  tegra: i2c: Add function to find DVC bus
  fdt: tegra: Add EMC node to device tree
  tegra: Add EMC settings for Seaboard
  tegra: Turn off power detect in board init
  tegra: Set up warmboot code on Nvidia boards
  tegra: Setup PMC scratch info from ap20 setup
  tegra: Add warmboot implementation
  tegra: Set up PMU for Nvidia boards
  tegra: Add PMU to manage power supplies
  tegra: Add EMC support for optimal memory timings
  tegra: Add header file for APB_MISC register
  tegra: Add tegra_get_chip_type() to detect SKU
  tegra: Add flow, gp_padctl, fuse, sdram headers
  tegra: Add crypto library for warmboot code
  tegra: Add functions to access low-level Osc/PLL details
  tegra: Move ap20.h header into arch location
  Add AES crypto library
  i2c: Add TPS6586X driver
  Add abs() macro to return absolute value
  fdt: Add function to return next compatible subnode
  fdt: Add function to locate an array in the device tree
  i.MX28: Avoid redefining serial_put[cs]()
  i.MX28: Check if WP detection is implemented at all
  i.MX28: Add battery boot components to SPL
  i.MX28: Reorder battery status functions in SPL
  i.MX28: Add LRADC init to i.MX28 SPL
  i.MX28: Add LRADC register definitions
  i.MX28: Shut down the LCD controller before reset
  i.MX28: Add LCDIF register definitions
  i.MX28: Implement boot pads sampling and reporting
  i.MX28: Improve passing of data from SPL to U-Boot
  M28EVK: Add SD update command
  M28EVK: Implement support for new board V2.0
  FEC: Abstract out register setup
  MX5: PAD_CTL_DRV_VOT_LOW and PAD_CTL_DRV_VOT_HIGH exchanged
  i.MX28: Add delay after CPU bypass is cleared
  spi: mxs: Allow other chip selects to work
  spi: mxs: Introduce spi_cs_is_valid()
  mx53loco: Remove unneeded gpio_set_value()
  mx53loco: Add CONFIG_REVISION_TAG
  mx53loco: Turn on VUSB regulator
  mx53loco: Add mc34708 support and set mx53 frequency at 1GHz
  pmic: dialog: Avoid name conflicts
  imx: Add u-boot.imx as target for ARM9 i.MX SOCs
  i.MX2: Include asm/types.h in arch-mx25/imx-regs.h
  imx: usb: There is no such register
  i.MX25: usb: Set PORTSCx register
  imx: nand: Support flash based BBT
  i.MX25: This architecture has a GPIO4 too
  i.MX25: esdhc: Add mxc_get_clock infrastructure
  i.MX6: mx6q_sabrelite: add SATA bindings
  i.MX6: add enable_sata_clock()
  i.MX6: Add ANATOP regulator init
  mx28evk: add NAND support
  USB: ehci-mx6: Fix broken IO access
  M28: Scan only first 512 MB of DRAM to avoid memory wraparound
  Revert "i.MX28: Enable additional DRAM address bits"
  M28: Enable FDT support
  mx53loco: Add support for 1GHz operation for DA9053-based boards
  mx53loco: Allow to print CPU information at a later stage
  mx5: Add clock config interface
  imx-common: Factor out get_ahb_clk()
  i.MX6Q: mx6qsabrelite: Add keypress support to alter boot flow
  mx31pdk: Allow booting a zImage kernel
  mx6qarm2: Allow booting a zImage kernel
  mx6qsabrelite: Allow booting a zImage kernel
  mx28evk: Allow booting a zImage kernel
  m28evk: Allow to booting a dt kernel
  mx28evk: Allow to booting a dt kernel
  mx6qsabrelite: No need to set the direction for GPIO3_23 again
  pmic: Add support for the Dialog DA9053 PMIC
  MX53: mx53loco: Add SATA support
  MX53: Add support to ESG ima3 board
  SATA: add driver for MX5 / MX6 SOCs
  MX53: add function to set SATA clock to internal
  SATA: check for return value from sata functions
  MX5: Add definitions for SATA controller
  NET: fec_mxc.c: Add a way to disable auto negotiation
  Define UART4 and UART5 base addresses
  EXYNOS: Change bits per pixel value proper for u-boot.
  EXYNOS: support TRATS board display function
  LCD: support S6E8AX0 amoled driver based on EXYNOS MIPI DSI
  EXYNOS: support EXYNOS MIPI DSI interface driver.
  EXYNOS: support EXYNOS framebuffer and FIMD display drivers.
  LCD: add data structure for EXYNOS display driver
  EXYNOS: add LCD and MIPI DSI clock interface.
  EXYNOS: definitions of system resgister and power management registers.
  SMDK5250: fix compiler warning
  misc:pmic:samsung Convert TRATS target to use MAX8997 instead of MAX8998
  misc:pmic:max8997 MAX8997 support for PMIC driver
  TRATS: modify the trats's configuration
  ARM: Exynos4: ADC: Universal_C210: Enable LDO4 power line for ADC measurement
  EXYNOS: Rename exynos5_tzpc structure to exynos_tzpc
  arm: ea20: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
  arm: cam_enc_4xx: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
  cm-t35: add I2C multi-bus support
  include/configs: Remove CONFIG_SYS_64BIT_STRTOUL
  include/configs: Remove CONFIG_SYS_64BIT_VSPRINTF
  omap3: Introduce weak misc_init_r
  omap730p2: Remove empty misc_init_r
  omap5912osk: Remove empty misc_init_r
  omap4+: Remove CONFIG_ARCH_CPU_INIT
  omap4: Remove CONFIG_SYS_MMC_SET_DEV
  OMAP3: pandora: drop console kernel argument
  OMAP3: pandora: revise GPIO configuration
  ...
2012-05-20 21:31:26 +02:00
Marek Vasut
c7527b70f9 i.MX28: Check if WP detection is implemented at all
If the WP function is NULL, simply assume the card is always RW.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-05-15 08:31:36 +02:00
Balaji T K
dd23e59d59 omap5: pbias ldo9 turn on
Add omap5 pbias configuration for mmc1/sd lines
and set voltage for sd data i/o lines

Signed-off-by: Balaji T K <balajitk@ti.com>
2012-05-15 08:31:25 +02:00
SRICHARAN R
002a2c0c66 OMAP4/5: Make the sysctrl structure common
Make the sysctrl structure common, so that it can
be used in generic functions across socs.
Also change the base address of the system control module, to
include all the registers and not simply the io regs.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15 08:31:24 +02:00
Jonathan Solnit
bbbc1ae921 ARM:OMAP+:MMC: Add parameters to MMC init
Add parameters to the OMAP MMC initialization function so the board can
mask host capabilities and set the maximum clock frequency.  While the
OMAP supports a certain set of MMC host capabilities, individual boards
may be more restricted and the OMAP may need to be configured to match
the board.  The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example.

Signed-off-by: Jonathan Solnit <jsolnit@gmail.com>
2012-05-15 08:31:22 +02:00
Jaehoon Chung
442d55685e mmc: support the sdhci instead of s5p_mmc for samsung-soc
In driver mmc, generic s5p_sdhci code is implemented.
s5p_mmc file  is dupulicated.
we are good that use the generic sdhci.
This patch supported the sdhci  for Samsung-SoC.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Lei Wen<leiwen@marvell.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
2012-05-08 18:02:22 -05:00
Jaehoon Chung
236bfecff8 mmc: add the quirk to use the sdhci for samsung-soc
To support the Samsung-SoC, added the basically functions.
Samsung-SoC didn't used the SDHCI_CTRL_HISPD.
And added set_control_reg callback for s3c64xx.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Lei Wen<leiwen@marvell.com>
2012-05-08 18:02:22 -05:00
Jaehoon Chung
3a6383207b mmc: sdhci: add the quirk for broken r1b response
When response type is R1b, mask value is added the SDHCI_INT_DAT_END.
but in while(), didn't check that flag.
So sdhci controller didn't work fine.
CMD6 didn't always complete.

So add the quirks for broken r1b response
and add the timeout value to prevent the infinite loop.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Lei Wen<leiwen@marvell.com>
2012-05-08 18:02:22 -05:00
Marek Vasut
e7205905e7 i.MX28: Lower the amount of blocks transfered in one DMA cycle
Some MMC cards, like my ancient 32.0MB SanDisk RS-MMC cards had issue if b_max
was set to 0x40 and DMA was enabled. Lower this value to 0x20, which allows
these cards to work too.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-08 18:02:22 -05:00
Dirk Behme
7a5b80297b mmc: fsl_esdhc: Poll until card is not busy anymore
This patch imports parts of two patches from the Freescale U-Boot with the following
commit messages:

ENGR00156405 ESDHC: Add workaround for auto-clock gate errata ENGcm03648
http://git.freescale.com/git/cgit.cgi/imx/uboot-imx.git/commit/drivers/mmc/imx_esdhc.c?h=imx_v2009.08_12.01.01&id=e436525a70fe47623d346bc7d9f08f12ff8ad787
The errata, not applicable to USDHC, causes ESDHC to shut off clock to the card
when auto-clock gating is enabled for commands with busy signalling and no data
phase. The card might require the clock to exit the busy state, so the workaround
is to disable the auto-clock gate bits in SYSCTL register for such commands. The
workaround also entails polling on DAT0 bit in the PRSSTAT register to learn when
busy state is complete. Auto-clock gating is re-enabled at the end of busy state.

ENGR00156670-1 ESDHC/USDHC: Remove delay before each cmd and some bug fixes
http://git.freescale.com/git/cgit.cgi/imx/uboot-imx.git/commit/drivers/mmc/imx_esdhc.c?h=imx_v2009.08_12.01.01&id=a77c6fec8596891be96b2cdbc742c9824844b92a
Removed delay of 10 ms before each command. There should not be a need to have this
delay after the ENGR00156405 patch that polls until card is not busy anymore before
proceeding to next cmd.

This patch imports the polling part of both patches. The auto-clock gating code
don't apply for i.MX6 as implemented in these two patches.

SYSCTL_RSTA was defined twice. Remove one definition.

Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Andy Fleming <afleming@freescale.com>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Stefano Babic <sbabic@denx.de>
2012-05-08 18:02:22 -05:00
Grazvydas Ignotas
25c719e2c3 mmc: omap: handle controller errors properly
According to OMAP3 TRM, when the controller reports certain errors,
driver must perform a software reset. This is done by setting a bit
in SYSCTL and waiting it to clear:
- SRC on command timeout (CTO)
- SRD on data errors (DTO, DCRC and DEB)

This fixes a problem seen on OMAP3 pandora board with some cards
that won't work with a message printed multiple times:
  timedout waiting on cmd inhibit to clear

Code loosely based on Linux omap_hsmmc driver.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Tom Rini <trini@ti.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
2012-05-08 18:02:22 -05:00
Grazvydas Ignotas
15ceb1de81 mmc: omap: improve stat wait message
The message didn't state that it's waiting for STAT to _clear_,
and printing the STAT value itself can help to identify problems.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Tom Rini <trini@ti.com>
2012-05-08 18:02:21 -05:00
Grazvydas Ignotas
b1e725f2c6 mmc: omap: follow TRM procedure to power on cards
According to OMAP3 TRM, PBIASLITEPWRDNZ bits must be cleared while MMC
power supply is being enabled and is ramping up (those bits might be
left set by the previous bootloader). It doesn't say what happens if
this procedure is violated, but better not to risk here and do things
as required.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Tom Rini <trini@ti.com>
2012-05-08 18:02:21 -05:00
Łukasz Majewski
6272203641 mmc:fix: Set mmc width according to MMC host capabilities
This patch sets the MMC width according to the MMC host capabilities.
It turned out, that there are some targets (e.g. GONI), which are able
to read data from SPI only at 4 bit mode.
This patch restricts the width number according to the MMC host.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Andy Fleming <afleming@gmail.com>
2012-05-08 18:02:21 -05:00
Mike Frysinger
51d0f7c694 Blackfin: bfin_sdh: drop dos part hardcode
No other driver sets up the part type to DOS in their init, and it
doesn't seem to be needed as `mmcinfo` and `mmc part` stll work, so
drop it.

Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-04-22 13:00:19 -04:00
Dirk Behme
146bec7905 mmc: Fix warning if CONFIG_MMC_TRACE is enabled
Fix the warning

mmc.c: In function 'mmc_send_cmd':
mmc.c:87: warning: assignment from incompatible pointer type

in case CONFIG_MMC_TRACE is enabled.

Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Andy Fleming <afleming@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
2012-04-21 17:04:04 +02:00
Marek Vasut
96666a39ae DMA: Split the APBH DMA init into block and channel init
This fixes the issue where mxs_dma_init() was called either twice or never,
without introducing any new init hooks.

The idea is to allow each and every device using the APBH DMA block to
configure and request only the channels it uses, instead of making it call init
for all the channels as is now.

The common DMA block init part, which only configures the block, is then called
from CPUs arch_cpu_init() call.

NOTE: This patch depends on:

	http://patchwork.ozlabs.org/patch/150957/

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-04-16 14:53:59 +02:00
Marek Vasut
4cc76c609f i.MX28: Allow coexistence of PIO and DMA mode for SD/MMC
This SD DMA function of i.MX28 is still apparently too experimental to be
enabled by default in 2012.04 release. Enable this feature only if the user
plans to tinker with DCache or explicitly enables it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-04-16 14:53:59 +02:00
Anatolij Gustschin
dc3faf09d7 drivers/mmc/mmc.c: Fix build warning
Fix:
mmc.c: In function 'mmc_bounce_buffer_start':
mmc.c:132:13: warning: no return statement in function returning
non-void [-Wreturn-type]

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
2012-03-30 22:14:15 +02:00
Anatolij Gustschin
60e242ed24 drivers/mmc/tegra2_mmc.c: fix GCC 4.6 warning
Fix:
tegra2_mmc.c: In function 'mmc_send_cmd':
tegra2_mmc.c:230:3: warning: 'mask' may be used uninitialized in this
function [-Wuninitialized]

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Tom Warren <twarren@nvidia.com>
2012-03-30 21:27:27 +02:00
Marek Vasut
3687c4155a i.MX28: Do data transfers via DMA in MMC driver
This utilizes the newly introduced bounce buffers in the MMC layer.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
2012-03-29 07:56:42 +02:00
Marek Vasut
8635ff9e99 MMC: Implement generic bounce buffer
This implements generic bounce buffer at the end of MMC command submission
chain. Therefore if unaligned data are passed, they are copied. This stuff
should be pushed down into the MMC subsystem to squash all places generating
these unaligned data.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@gmail.com>
2012-03-29 07:56:39 +02:00
Sven Schnelle
c9abb4260c ATMEL: remove old atmel_mci driver
All boards are using the gen_atmel_mci driver now, so no need
to carry the old driver around.

Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-03-13 12:06:42 +01:00
Sven Schnelle
72fa467988 ATMEL: use generic mmc framework
gen_atmel_mci works on AVR32 as well, so no need to use the legacy
mmc driver. This also has the nice side effect of being able to use
SDHC cards an those boards.

Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-03-13 12:06:41 +01:00
Jan Kloetzke
d617c426a6 mmc: make mmc_send_status() more reliable
Align the card status polling with the Linux kernel and retry the
command at least five times. Also some cards apparently mishandle the
status bits, so make sure to check the card state too.

Signed-off-by: Jan Kloetzke <jan.kloetzke@dspg.com>
Cc: Andy Fleming <afleming@gmail.com>
2012-02-15 17:42:22 -06:00
Jan Kloetzke
93ad0d18c0 mmc: fix card busy polling
A MMC/SD card may always go into the programming state (and hence be
busy) after a block write. Therefore always check the card state, even
after single block writes. On the other hand there is no need to check
the card status after a read.

Also make sure that errors during busy polling are propagated upwards.

Signed-off-by: Jan Kloetzke <jan.kloetzke@dspg.com>
Cc: Andy Fleming <afleming@gmail.com>
2012-02-15 17:42:22 -06:00
Tom Warren
cf39cf5597 Tegra: mmc: Fixed handling of interrupts in timeouts.
We are seeing occasional timeouts in the Tegra mmc code when
we are reading from external MMC cards. These don't seem to be
detrimental if they are handled properly.  This CL properly
clears the "normal interrupt status register" (norintsts) in
error conditions.  If we don't do this, when we come back into
mmc_send_cmd() the register will still contain status from the
last transaction.

Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-02-15 17:42:22 -06:00
Tom Rini
a7778f8fbe omap_hsmmc: Wait for CMDI to be clear
Before we can send a command we need both the DATI (command inhibit on
mmc_dat line) bit and CMDI (command inhibit on mmc_cmd line) are clear.
The previous behavior of only checking on DATI was insufficient on some
cards and incorrect behavior in any case.  This makes the code check
for both bits being clear and makes the error print more clear as
to what happened.  DATI_CMDDIS is removed as it was unused elsewhere
in the code and stood for 'DATI is set, cmds are disabled still'.

Fix originally spotted by Peter Bigot.

Tested-by: Peter A. Bigot <bigotp@acm.org>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Andreas Müller <schnitzeltony@googlemail.com>
2012-02-15 17:42:22 -06:00
Helmut Raiger
fa47a28661 mmc: access mxcmmc from mx31 boards
This patch modifies mxcmmc.c to be used
not only by i.MX27 but also by i.MX31 boards.
Both use the same SD controller, but have different
clock set-ups.
The i.MX27 imx_get_XXXclock functions are made static to
generic.c and a public mxc_get_clock() function
is provided.  Pins, base address and prototypes for
an i.MX31 specific board_init_mmc() are provided.
Some of the i.MX27 clock getters are unused and marked
as such to avoid warnings (./MAKEALL -s mx27), but
the code was left in for future use.

Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-02-12 10:11:26 +01:00
Simon Glass
98450d0220 tegra: mmc: Support operation with dcache enabled
When the data cache is enabled we must flush on write and invalidate
on read. We also check that buffers are aligned to data cache lines
boundaries. With recent work in U-Boot this should generally be the case
but the warnings will catch problems.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-02-12 10:11:22 +01:00
Ira Snyder
8eee2bd7f4 fsl_esdhc: fix PIO mode transfers
The pointer to the registers used to control the Freescale ESDHC MMC
controller is not initialized correctly when using PIO mode. This is
fixed by initializing the pointer in the same way as all other sites
within the driver.

Examining the commit history shows that this was broken at introduction
due to a code change in upstream U-Boot to support the mx51 processor
family.

Reported-by: Jim Lentz <JLentz@zhone.com>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
2012-01-08 21:28:28 -06:00
Thierry Reding
bf83662ba3 mmc: tegra2: Implement card-detect hook.
On Tegra2, card-detection is implemented by passing the card-detection
GPIOs to the MMC driver at initialization time. Instead of implementing
the board_mmc_getcd() function, use the card-detect hook and allow
boards to override it by providing their own board_mmc_getcd()
implementation.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
2012-01-08 21:28:28 -06:00
Thierry Reding
d48d2e21d4 mmc: fsl_esdhc: Implement card-detect hook.
This card-detect hook probably doesn't work. Perhaps somebody with more
knowledge about the hardware can comment on this. I think that perhaps
even the complete code from esdhc_init() could go into the getcd()
function instead or mmc_getcd() needs to be called at some later time
after mmc_init(), which, however, would require many other drivers to
change.

In addition to implementing the hook, this patch also removes the call
to the board_mmc_getcd() function which is now called from the MMC
framework and is no longer required here.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Jason Liu <jason.hui@linaro.org>
2012-01-08 21:28:28 -06:00
Thierry Reding
48972d907a mmc: Implement card detection.
Check for card detect each time an MMC/SD device is initialized. If card
detection is not implemented, this code behaves as before and continues
assuming a card is present. If no card is detected, has_init is reset
for the MMC/SD device (to force initialization next time) and an error
is returned.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Jason Liu <jason.hui@linaro.org>
2012-01-08 21:28:27 -06:00
Thierry Reding
314284b156 mmc: Change board_mmc_getcd() function prototype.
The new API no longer uses the extra cd parameter that was used to store
the card presence state. Instead, this information is returned via the
function's return value. board_mmc_getcd() returns -1 to indicate that
no card-detection mechanism is implemented; 0 indicates that no card is
present and 1 is returned if it was detected that a card is present.

The rationale for this change can be found in the following email
thread:

	http://lists.denx.de/pipermail/u-boot/2011-November/110180.html

In summary, the old API was not consistent with the rest of the MMC API
which always passes a struct mmc as the first parameter. Furthermore the
cd parameter was used to mean "card absence" in some implementations and
"card presence" in others.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Jason Liu <jason.hui@linaro.org>
2012-01-08 21:28:27 -06:00
Anatolij Gustschin
bfe6f6235f drivers/mmc/mv_sdhci.c: Fix build warning
Fix:
mv_sdhci.c: In function 'mv_sdh_init':
mv_sdhci.c:47:22: warning: the comparison will always
evaluate as 'true' for the address of 'mv_sdhci_writeb'
will never be NULL [-Waddress]

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Andy Fleming <afleming@freescale.com>
Acked-by: Lei Wen <leiwen@marvell.com>
2012-01-08 21:28:16 -06:00
Macpaul Lin
31cb6db5db ftsdc010: improve performance and capability
This patch improve the performance by spliting flag examination code
in ftsdc010_send_cmd() into 3 functions.
This patch also reordered the function which made better capability to
some high performance cards against to the next version of ftsdc010
hardware.

Signed-off-by: Macpaul Lin <macpaul@andestech.com>
2012-01-08 21:28:16 -06:00
Macpaul Lin
2c3fbf4cbe mmc: add host_caps checking avoid switch card improperly
Add a host capability checking to avoid the mmc stack
switch the card to HIGHSPEED mode when the card supports
HIGHSPEED while the host doesn't.

This patch avoid furthur transaction problem when the
mmc/sd card runs different mode to the host.

Signed-off-by: Macpaul Lin <macpaul@andestech.com>
2012-01-08 21:28:16 -06:00
Jason Liu
4692708d45 i.mx: fsl_esdhc: add the i.mx6q support
The mmc host controller on the i.mx6q is called usdhc which
is redesigned based on the freescale esdhc controller.

The usdhc controller is almost compatible with esdhc except
it adds one mix register to support debug/SD3.0 and move
the low bit 0-6 of XFERTYP register to the mix control reg
low bit 0-6. Thus on i.mx6q, we have the following compared
with the previous soc: (can refer to RM of chapter 56.3.3)

i.mx6q:
mix control:
bit 31 - bit 7: Added for debug/SD3.0 support
bit 6  - bit 0: move in the XFERTYP register bit 6-0 on previous soc
XFERTYP register:
bit 31 - bit 7: the same as before,
bit 6  - bit 0: no-use

previous soc
mix control: no
XFERTYP register:
bit 31 - bit 0: xfertype information

Signed-off-by: Jason Liu <jason.hui@linaro.org>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-01-08 21:28:16 -06:00
Thierry Reding
977a39e600 tegra2: Move tegra2_mmc_init() prototype to public header.
tegra2_mmc_init() is implemented by the Tegra2 MMC driver. Since most of
the Tegra2-based boards will need to call it, this commit exports it in
the new public asm/arch/mmc.h header file to prevent each board from
providing its own prototype.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2011-12-24 10:23:31 +01:00
Marek Vasut
e570fe8ef2 PXA: Kill last remnants of set_GPIO_mode function
GPIO configuration shall never be done inside a driver, never.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-12-19 17:52:44 +01:00
Stephen Warren
9877841f6b tegra2: Modify MMC driver to handle power and cd GPIOs
Pass the GPIO numbers for power and card detect to tegra2_mmc_init(), and
modify that function to perform all required GPIO initialization. This
removes the need for board files to perform these operations.

Move board_mmc_getcd() into tegra2_mmc.c now that the driver knows which
GPIOs to use.

Update affected call-sites in seaboard.c and harmony.c. Note that this
change should make all SD ports work on Harmony, since the required GPIO
setup is now being performed.

v4: Fix prototype of tegra2_mmc_init() in board.h to match driver change.
    Remove prototype of gpio_config_mmc() from board.h

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: Andy Fleming <afleming@gmail.com>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2011-12-09 17:30:08 +01:00
Marek Vasut
abc20aba18 PXA: Rename CONFIG_PXA2[57]X to CONFIG_CPU_PXA2[57]X
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2011-12-06 23:59:32 +01:00
Macpaul Lin
afd5932b2c Revert "mmc: retry the cmd8 to meet 74 clocks requirement in the spec"
This reverts commit 02f3029f18.

This patch add 3 times retry to CMD8 because the Marvell mmc controller
doesn't obey the power ramp up process in the SD specification 6.4.1.
(Please refer to figure 6.1 and 6.2 in the specification.)

The CMD0 should be send after power ramp up has been finished.
However, the Marvell mmc contorller must do power ramp up after the
first CMD0 command has been send.

This patch also affect existing platforms like Nokia N900 and other
platforms.

Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Acked-by: Lei Wen <leiwen@marvell.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
2011-11-25 17:43:05 -06:00
Ajay Bhargav
5af9a56999 mmc: mv_sdhci: Fix host version read for Armada100
sdhci_readw does not work for host version read in Armada100 series
SoCs. This patch fix this issue by making a sdhci_readl call to get host
version.

Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
2011-11-25 17:43:05 -06:00
Heiko Schocher
79b05d59ad davinci, mmc: fix gcc 4.6 build warnings
Fix:
davinci_mmc.c: In function 'dmmc_wait_fifo_status':
davinci_mmc.c:72:7: warning: variable 'mmcstatus1' set but not used [-Wunused-but-set-variable]
davinci_mmc.c: In function 'dmmc_busy_wait':
davinci_mmc.c:89:7: warning: variable 'mmcstatus1' set but not used [-Wunused-but-set-variable]

Delete the unused variable.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-11-16 20:51:14 +01:00
Wolfgang Denk
0c2dd9a05b Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
  arm, davinci: add DAVINCI_MMC_CLKID
  arm, davinci_emac: fix driver bug if more then 3 PHYs are detected
  arm, davinci: da850/dm365 lowlevel cleanup
  omap5: Add omap5_evm board build support.
  omap4/5: Add support for booting with CH.
  omap5: emif: Add emif/ddr configurations required for omap5 evm
  omap5: clocks: Add clocks support for omap5 platform.
  omap5: Add minimal support for omap5430.
  omap: Checkpatch fixes
  omap4: make omap4 code common for future reuse
  GCC4.6: Squash warnings in onenand_base.c
  GCC4.6: Fix common/usb.c on xscale
  OneNAND: Add simple OneNAND SPL
  PXA: vpac270: Enable the new generic MMC driver
  PXA: Cleanup serial_pxa
  PXA: Drop csb226 and innokom boards (unmaintained)
  m28evk: Fix comment about the number of RAM banks
  mx31: Fix checkpatch warnings in generic.c
  mx31: Use proper IO accessor for GPR register
  mx31: Remove duplicate definition for GPR register
  qong: Use generic function for configuring GPR register
  M28EVK: Enable USB HOST support
  iMX28: Add USB HOST driver
  iMX28: Add USB and USB PHY register definitions
  M28: Add memory detection into SPL
  iMX28: Fix ARM vector handling
  M28: Add doc/README.m28 documentation
  M28: Add MMC SPL
  iMX28: Add support for DENX M28EVK board
  iMX28: Add u-boot.sb target to Makefile
  iMX28: Add image header generator tool
  iMX28: Add driver for internal RTC
  iMX28: Add GPMI NAND driver
  iMX28: Add APBH DMA driver
  iMX28: Add SPI driver
  iMX28: Add GPIO control
  iMX28: Add I2C bus driver
  iMX28: Add PINMUX control
  FEC: Add support for iMX28 quirks
  iMX28: Add SSP MMC driver
  iMX28: Initial support for iMX28 CPU
  MX25: zmx25: GCC4.6 fix build warnings
  da850: add new config file for AM18xx
  BeagleBoard: config: Switch to ttyO2
  OMAP3: Change omap3_evm maintainer
  devkit8000: Fix NAND SPL on boards with 256MB NAND
  integrator: enable Vpp and disable flash protection
  integrator: add system controller header
  integrator: make flash writeable on boot
  integrator: use io-accessors for board init
  integrator: move text offset to config
  integrator: pass configs for core modules
  ARM: remove superfluous setting of arch_number in board specific code.
  SPL: Allow ARM926EJS to avoid compiling in the CPU support code
  integrator: do not test first part of the memory
  arm: a320: fix broken timer
  ARM: define CONFIG_MACH_TYPE for all ronetix boards
  dm646x: pass board revision info to kernel
  dm646x: add new configuration for dm6467T
  arm, davinci: Fix setting of the SDRAM configuration register
  arm, davinci: Remove the duplication of LPSC functions
  arm, davinci: Rename AM1808 lowlevel functions to DA850
  da8xxevm: fix build error
  ARM: re-add MACH_TYPE_XXXXXX for VCMA9 board and add CONFIG_MACH_TYPE
2011-11-16 20:24:41 +01:00
Sricharan
933efe641a omap: Checkpatch fixes
Fixing them here so that when the files are reused in
subsequent patches for omap5, avoids new checkpatch
warnings.

Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15 22:25:50 +01:00
Anton staaf
0963ff3a97 Tegra2: mmc: Factor out mmc_wait_inhibit functionality
This is a well encapsulated section of mmc_send_cmd, by moving
it to it's own function it increases the readability of mmc_send_cmd.

Signed-off-by: Anton Staaf <robotboy@chromium.org>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2011-11-12 15:39:29 -06:00
Anton staaf
9b3d1873c8 Tegra2: mmc: Add data transfer completion timeout
Currently when no expected completion condition occures in the
mmc_send_cmd while loop that is waiting for a data transfer to
complete the MMC driver just hangs.

This patch adds an arbitrary 2 second timeout.  If nothing we
recognize occures within 2 seconds some diagnostic information
is printed and we fail out.

Signed-off-by: Anton Staaf <robotboy@chromium.org>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2011-11-12 15:39:29 -06:00
Anton staaf
5a762e2509 Tegra2: mmc: Support DMA restarts at buffer boundaries
Currently if a DMA buffer straddles a buffer alignment boundary
(512KiB) then the DMA engine will pause and generate a DMA
interrupt.  Since the DMA interrupt is not enabled it will hang
the MMC driver.

This patch adds support for restarting the DMA transfer.  The
SYSTEM_ADDRESS register contains the next address that would have
been read/written when a boundary is hit.  So we can read that
and write it back.  The write triggers the resumption of the
transfer.

Signed-off-by: Anton Staaf <robotboy@chromium.org>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2011-11-12 15:39:29 -06:00
Anton staaf
8e42f0d62b Tegra2: mmc: define register field values in tegra2_mmc.h
This moves the magic numbers sprinkled about the MMC driver
to a single location in the header file and gives them
meaningful names.

Signed-off-by: Anton Staaf <robotboy@chromium.org>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2011-11-12 15:39:29 -06:00
Marek Vasut
71a758e158 iMX28: Add SSP MMC driver
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Acked-by: Andy Fleming <afleming@gmail.com>
2011-11-11 11:36:56 +01:00
Jon Medhurst (Tixy)
0612fcbcb1 MMC: PL180: Fix infinite loop with VExpress extended fifo implementation
The new IO FPGA implementation for Versatile Express contains an MMCI
(PL180) cell with the FIFO extended to 128 words. This causes the
read_bytes() function to go into an infinite loop; as it will wait for
for the half-full signal (SDI_STA_RXFIFOBR) if there are more than 8
words remaining (SDI_FIFO_BURST_SIZE), but it won't receive this signal
once there are fewer than 64 words left to transfer.

One possible fix is to add some build time configuration to change
SDI_FIFO_BURST_SIZE for the new implementation. However, the problematic
code only seems to exist as a small performance optimisation, so the
solution implemented by this patch is to simply remove it. The error
checking following the loop is also removed as this will be handled by
code further down the function.

Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Jon Medhurst <jon.medhurst@linaro.org>
2011-11-08 14:39:58 -06:00
Stephen Warren
de71fbe468 tegra2: Move MMC clock initialization into MMC driver
This centralizes knowledge of MMC clocking into the MMC driver. This also
removes clock setup from the board files, which will simplify later changes
that modify the Harmony board to support the correct set of MMC controllers.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: Andy Fleming <afleming@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2011-11-03 02:15:00 -05:00
Lei Wen
3e81c77240 mmc: sdhci: fix sdma bug for large file transfer
SDHCI spec need to reset the sdma base address while the software
try to accorss the 512k bytes address boundary. When meet such
accross behavior, sdhci controller would generate a interrupt
automatically, and software need handle this.

Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-11-03 02:15:00 -05:00
Lei Wen
a004abde88 mmc: sdhci: add timeout for data transfer
Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-11-03 02:14:59 -05:00
Lei Wen
6cf1b17cd0 mmc: sdhci: add mmc structure for host
So that sdhci host would tell in the driver that the mmc current
attributes.

Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-11-03 02:14:59 -05:00
Lei Wen
2c2ec4c969 mmc: sdhci: fix cache flush
Only flush the memory range needed.

Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-11-03 02:14:59 -05:00
Ajay Bhargav
fe8f7066d3 mmc: CMD7:MMC_CMD_SELECT_CARD response fix
As per JEDEC document JESD84-A441 (page 105) response for CMD7
(MMC_CMD_SELECT_CARD) response should be R1 instead of R1b. In uboot we
never take MMC to disconnected state and on powerup its always ideal
state which later goes to stand-by state.

from document footnote:
R1 while selecting from Stand-By State to Transfer State; R1b while
selecting from Disconnected State to Programming State.

Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
2011-11-03 02:14:59 -05:00
Lei Wen
4137894e04 mmc: test mmc bus width on startup
For we don't know mmc bus width from reading registers, the only way
to check is to test.

Current compare offset is:
EXT_CSD_PARTITIONING_SUPPORT
EXT_CSD_ERASE_GROUP_DEF
EXT_CSD_REV
EXT_CSD_HC_ERASE_GRP_SIZE
EXT_CSD_SEC_CNT

Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-11-03 02:14:59 -05:00
Lei Wen
0560db18ec mmc: change magic number to macro define
Previous magic number is hard to parse its meaning, change it to
respective macro definition

Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: WOlfgang Denk <wd@denx.de>
2011-11-03 02:14:58 -05:00
Lei Wen
02d3ad3e19 mmc: mv_sdhci: fix 8bus width access for 88SV331xV5
Marvell 88SV331xV5 platform's sdhci host control is not very standard
with the spec in the 8bit handling. It need to set its private register
to switch to the 8bit mode which is not included in the standard sdhci
registers.

This patch mainly hacks the writeb method, and set its private register
if it find the driver is going to switch to the 8bit mode.

Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-11-03 02:14:58 -05:00
Lei Wen
02f3029f18 mmc: retry the cmd8 to meet 74 clocks requirement in the spec
For some controller it has dynamic clock gating, and only toggle out clk
when the first cmd0 send out, while some card strictly obey the 74
clocks rule, the interval may not be sufficient between the cmd0 and
this cmd8, retry to fulfil the clock requirement.

Signed-off-by: Lei Wen <leiwen@marvell.com>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
2011-11-03 02:14:58 -05:00
Marek Vasut
07133f2e7b PXA: Add MMC driver using the generic MMC framework
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2011-11-03 02:14:58 -05:00
Wolfgang Denk
87a5d60103 Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
  ARM: Add Calxeda Highbank platform
  dkb: make mmc command as default enabled
  Marvell: dkb: add mmc support
  ARM: pantheon: add mmc definition
  davinci: remove config.mk file from the sources
  ARM:AM33XX: Add support for TI AM335X EVM
  ARM:AM33XX: Added timer support
  ARM:AM33XX: Add emif/ddr support
  ARM:AM33XX: Add clock definitions
  ARM:AM33XX: Added support for AM33xx
  omap3/emif4: fix registers definition
  davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUM
  davinci: emac: add support for more than 1 PHYs
  davinci: emac: add new features to autonegotiate for EMAC
  da850evm: Move LPSC configuration to board_early_init_f()
  omap4_panda: Build in cmd_gpio support on panda
  omap: Don't use gpio_free to change direction to input
  mmc: omap: Allow OMAP_HSMMC[23]_BASE to be unset
  OMAP3: overo : Add environment variable optargs to bootargs
  OMAP3: overo: Move ethernet CS4 configuration to execute based on board id
  OMAP3: overo : Use ttyO2 instead of ttyS2.
  da830: add support for NAND boot mode
  dm36x: revert cache disable patch
  dm644X: revert cache disable patch
  devkit8000: Add malloc space
  omap: spl: fix build break due to changes in FAT
  OMAP3 SPL: Provide weak omap_rev_string
  omap: beagle: Use ubifs instead of jffs2 for nand boot
  omap: overo: Disable pull-ups on camera PCLK, HS and VS signals
  omap: overo: Configure mux for gpio10
  SPL: Add DMA library
  omap3: Add interface for omap3 DMA
  omap3: Add DMA register accessors
  omap3: Add Base register for DMA
  arm, davinci: add missing LSPC define for MMC/SD1
  U-Boot/SPL: omap4: Make ddr pre-calculated timings as default.
  DaVinci: correct MDSTAT.STATE mask
  omap4: splitting padconfs into common, 4430 and 4460
  omap4: adding revision detection for 4460 ES1.1
  omap4: replacing OMAP4_CONTROL with OMAP4430_CONTROL
  gplug: fixed build error as a result of code cleanup patch
  kirkwood_spi: add dummy spi_init()
  gpio: mvmfp: reduce include platform file
  ARM: orion5x: reduce dependence of including platform file
  serial: reduce include platform file for marvell chip
  ARM: kirkwood: reduce dependence of including platform file
  ARM: armada100: reduce dependence of including platform file
  ARM: pantheon: reduce dependence of including platform file
  Armada100: Add env storage support for Marvell gplugD
  Armada100: Add SPI flash support for Marvell gplugD
  Armada100: Add SPI support for Marvell gplugD
  SPI: Add SPI driver support for Marvell Armada100
  dreamplug: initial board support.
  imx: fix coding style
  misc: pmic: drop old Freescale's pmic driver
  MX31: mx31pdk: use new pmic driver
  MX31: mx31ads: use new pmic driver
  MX31: mx31_litekit: use new pmic driver
  MX5: mx53evk: use new pmic driver
  MX5: mx51evk: use new pmic driver
  MX35: mx35pdk: use new pmic driver
  misc: pmic: addI2C  support to pmic_fsl driver
  misc: pmic: use I2C_SET_BUS in pmic I2C
  MX5: efikamx/efikasb: use new pmic driver
  MX3: qong: use new pmic driver
  RTC: Switch mc13783 to generic pmic code
  MX5: vision2: use new pmic driver
  misc: pmic: Freescale PMIC switches to generic PMIC driver
  misc:pmic:samsung Enable PMIC driver at GONI target
  misc:pmic:max8998 MAX8998 support at a new PMIC driver.
  misc:pmic:core New generic PMIC driver
  mx31pdk: Remove unneeded config
  mx31: provide readable WEIM CS accessor
  MX51: vision2: Set global macros
  I2C: Add i2c_get/set_speed() to mxc_i2c.c
  ARM: Update mach-types
  devkit8000: Add config to enable SPL MMC boot
  devkit8000: protect board_mmc_init
  arm, post: add missing post_time_ms for arm
  cosmetic, post: Codingstyle cleanup
  arm, logbuffer: make it compileclean
  tegra2: Enable MMC for Seaboard
  tegra2: Add more pinmux functions
  tegra2: Rename PIN_ to PINGRP_
  tegra2: Add more clock functions
  tegra2: Clean up board code a little
  tegra2: Rename CLOCK_PLL_ID to CLOCK_ID
2011-10-28 00:15:19 +02:00
Marek Vasut
a231f04f1a GCC4.6: Fix warnings in pxa_mmc.c
pxa_mmc.c: In function 'mmc_cmd':
pxa_mmc.c:77:2: warning: format '%08x' expects type 'unsigned int', but argument
2 has type 'ulong'
pxa_mmc.c: In function 'mmc_block_read':
pxa_mmc.c:110:2: warning: format '%d' expects type 'int', but argument 4 has
type 'ulong'
pxa_mmc.c: In function 'pxa_mmc_write':
pxa_mmc.c:327:2: warning: format '%lx' expects type 'long unsigned int', but
argument 2 has type 'uchar *'
pxa_mmc.c:349:2: warning: format '%lx' expects type 'long unsigned int', but
argument 2 has type 'uchar *'
pxa_mmc.c:354:3: warning: format '%lx' expects type 'long unsigned int', but
argument 2 has type 'uchar *'
pxa_mmc.c:362:2: warning: format '%lx' expects type 'long unsigned int', but
argument 2 has type 'uchar *'
pxa_mmc.c:367:3: warning: format '%lx' expects type 'long unsigned int', but
argument 2 has type 'uchar *'

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
2011-10-27 23:54:06 +02:00
Tom Rini
1037d585d3 mmc: omap: Allow OMAP_HSMMC[23]_BASE to be unset
Not all omap families define OMAP_HSMMC[23]_BASE so condition those
cases in omap_mmc_init().

Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-10-27 21:56:35 +02:00
Tom Warren
ccf7988b9a tegra2: Enable MMC for Seaboard
This adds the required GPIO and pinmux configuration to make eMMC / SD work
on Seaboard.

Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Warren <twarren@nvidia.com>
2011-10-27 21:56:29 +02:00
Simon Glass
4ed59e70e4 tegra2: Add more clock functions
This adds most of the clock functions required by board and driver code:

-query and adjust peripheral clocks
-query and adjust PLLs
-reset and enable control

These functions are plumbed in as required.

Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Warren <twarren@nvidia.com>
2011-10-27 21:56:29 +02:00
Anton staaf
a1969923c9 mmc: dcache: allocate cache aligned buffers for ext_csd
Currently the mmc_change_freq and mmc_startup functions allocates
buffers on the stack that are passed down to the MMC device driver.
These buffers could be unaligned to the L1 dcache line size.  This
causes problems when using DMA and with caches enabled.

This patch correctly cache alignes the buffers used for reading the
ext_csd data from an MMC device.

Signed-off-by: Anton Staaf <robotboy@chromium.org>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-10-25 09:26:14 +02:00
Anton staaf
f781dd383a mmc: dcache: allocate cache aligned buffer for scr and switch_status
Currently the sd_change_freq function allocates two buffers on the
stack that it passes down to the MMC device driver.  These buffers
could be unaligned to the L1 dcache line size.  This causes problems
when using DMA and with caches enabled.

This patch correctly cache alignes the buffers used for reading the
scr register and switch status values from an MMC device.

Change-Id: Ifa8414f572ef907681bd2d5ff3950285a215357d
Signed-off-by: Anton Staaf <robotboy@chromium.org>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-10-25 09:25:13 +02:00
Balaji T K
14fa2dd00f mmc: omap: config VMMC, MMC1_PBIAS
Config VMMC voltage to 3V for MMC/SD card slot
and PBIAS settings needed for OMAP4
Fixes MMC/SD detection on boot from eMMC.

Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30 22:00:55 +02:00
Balaji T K
ecd9af88ac mmc: omap: enable high capacity
Enable high capacity to host capability.
Fixes eMMC detection on boot from MMC/SD card.

Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30 22:00:55 +02:00
Macpaul Lin
f8ef0d4f46 ftsdc010: add support of ftsdc010 mmc controller
Faraday FTSDC010 controller is a SD/MMC controller for SoC chip.

Signed-off-by: Macpaul Lin <macpaul@andestech.com>
2011-09-04 18:03:02 -05:00
Marek Vasut
aaf3d41aa0 mmc: Fix mmc_send_status()
The mmc_send_status() function sets cmd.arg = 0. That's incorrect, so fix it.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Tested-by: Lei Wen <adrian.wenl@gmail.com>
2011-09-04 18:03:02 -05:00
Tom Rini
c318dbf079 OMAP3: Remove legacy mmc driver
Now that all platforms have been migrated to the new MMC driver, remove
the old one.

Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-04 11:36:18 +02:00
Anton Staaf
9070872bb3 mmc: S5P: Support DMA restarts at buffer boundaries
Currently if a DMA buffer straddles a buffer alignment boundary
(512KiB) then the DMA engine will pause and generate a DMA
interrupt.  Since the DMA interrupt is not enabled it will hang
the MMC driver.

This patch adds support for restarting the DMA transfer.  The
SYSTEM_ADDRESS register contains the next address that would have
been read/written when a boundary is hit.  So we can read that
and write it back.  The write triggers the resumption of the
transfer.

Signed-off-by: Anton Staaf <robotboy@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Tested-by : Jaehoon Chung <jh80.chung@samsung.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-09-03 22:40:47 +02:00
Andy Fleming
0011401dfe Revert "AT91:mmc:fix multiple read/write error"
This reverts commit c310fc8404.

The Atmel custodian had apparently rejected this patch's approach in
another thread, so this patch reverts it for now.

Signed-off-by: Andy Fleming <afleming@freescale.com>
2011-07-28 20:47:15 -05:00
Matthew McClintock
df3fc52608 disk/part.c: Make features optional
If we don't want to build support for any partition types we can now
add #undef CONFIG_PARTITIONS in a board config file to keep this from
being compiled in. Otherwise boards assume this is compiled in by
default

Signed-off-by: Matthew McClintock <msm@freescale.com>
2011-07-26 14:10:14 +02:00
elen.song
c310fc8404 AT91:mmc:fix multiple read/write error
According to datasheet,set block count before multiple read/write.

Signed-off-by: elen.song <elen.song@atmel.com>
Acked-by: Andy Fleming <afleming@freescale.com>
2011-07-15 20:29:21 -05:00
Łukasz Majewski
b1f1e821d3 mmc: Access mode validation for eMMC cards > 2 GiB
This patch provides handling of the two way handshake when SEND_OP_COND
(CMD1) is send to mmc card. It is necessary to inform eMMC card if the
host can work with high capacity cards (Jedec JESD84-A441, point 7.4.3).

The extra flag MMC_MODE_HC (high capacity) is added to indicate if the
host is capable of handling the high capacity eMMC cards.

Since this change is added to the generic mmc framework, then it requires
other boards to indicate if their mmc controllers can handle high capacity
cards. As it is now - the old behaviour of the framework is preserved.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2011-07-15 20:29:21 -05:00
Yoshihiro Shimoda
afb35666da mmc: sh_mmcif: add support for Renesas MMCIF
Some Renesas SuperH have MMCIF module. This driver supports it.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Andy Fleming <afleming@freescale.com>
2011-07-15 20:29:21 -05:00
Yoshihiro Shimoda
639b7827d1 mmc: fix the condition for MMC version 4
Fix the problem that if we use the chip of MMC version 4 and
the capacity is smaller than 2GB or equal, the mmc->capacity is
invalid. According to the JEDEC Standard, the value of ext_csd's
capacity is valid if the value is more than 2GB.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Andy Fleming <afleming@freescale.com>
2011-07-15 20:29:20 -05:00
Lei Wen
e75787d903 MMC: add marvell sdhci driver
This could support both armada100 and pantheon serial in the mainline,
while this driver also be tested to support upcoming mg, mmp2 and mmp3
hardware.

Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
2011-07-15 20:29:19 -05:00
Lei Wen
af62a55785 MMC: add sdhci generic framework
Nowdays, there are plenty of mmc driver in uboot adopt the sd standard
host design, aka as sdhci. It is better to centralize the common logic
together to better maintenance.

Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
2011-07-15 20:29:18 -05:00
Lei Wen
e6f99a5611 MMC: add erase function to both mmc and sd
Erase is a very basic function since the begin of sd specification is
announced. Although we could write a bulk of full 0xff memory to the
range to take place of erase, it is more convenient and safe to
implement the erase function itself.

Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-07-15 20:29:17 -05:00
Tom Warren
21ef6a109c mmc: Tegra2: SD/MMC driver for Seaboard - eMMC on SDMMC4, SDIO on SDMMC3
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Andy Fleming <afleming@freescale.com>
2011-07-15 20:28:56 -05:00
Jaehoon Chung
68a8cbfad9 S5P: add set_mmc_clk for external clock control
This patch added set_mmc_clk for external clock control.

c210 didn't support host clock control.
So We need external_clock_control function for c210.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2011-05-26 19:33:09 +09:00
Dirk Behme
810423f405 MMC S5P: Fix typo
Fix typo resulting in the compilation error

s5p_mmc.c: In function 's5p_mmc_initialize':
s5p_mmc.c:469: error: 'struct mmc' has no member named 'm_bmax'

introduced by commit "MMC: make b_max unconditional"
(8feafcc49c)

Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
CC: John Rigby <john.rigby@linaro.org>
CC: Andy Fleming <afleming@freescale.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2011-05-26 19:30:19 +09:00
Wolfgang Denk
cd6881b519 Minor coding style cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-05-19 22:22:44 +02:00
Dirk Behme
96e0e7b36c MMC: omap_hsmmc.c: Add missing prototype header
Add missing header file to fix compilation warning

omap_hsmmc.c: In function 'omap_mmc_init':
omap_hsmmc.c:474: warning: implicit declaration of function 'get_cpu_family'
omap_hsmmc.c:474: warning: implicit declaration of function 'get_cpu_rev'

introduced by commit "MMC: omap_hsmmc.c: disable
multiblock rw on old rev omap34xx silicon"
(4ca9244d74)

Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
CC: Andy Fleming <afleming@freescale.com>
CC: John Rigby <john.rigby@linaro.org>
2011-05-18 14:38:05 -05:00
Fabio Estevam
1ed60d7ade fsl_esdhc: Initialize mmc->b_max
commit 262951(MMC: make b_max unconditional) missed to update fsl_esdhc.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2011-05-18 14:37:45 -05:00
Lei Wen
bc897b1d4d mmc: enable partition switch function for emmc
For emmc, it may have up to 7 partitions: two boot partitions, one
user partition, one RPMB partition and four general purpose partitions.
(Refer to JESD84-A44.pdf/page 154)

As bootloader may need to read out or reflashing images on those

different partitions, it is better to enable the partition switch with
console command support.

Also for partition would be restore to user partition(part 0) when CMD0
is used, so change mmc_init routine to perform normal initialization
only once for each slot, unless use the rescan command to force init
again.

Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
2011-05-18 14:37:03 -05:00
Lei Wen
ea6ebe2177 cmd_mmc: eliminate device num in the mmc command
mmc command applied device, like ide and usb...

Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
2011-05-18 14:36:35 -05:00
Thomas Chou
ed018b21d6 mmc_spi: generate response for send status command
A "send status" command is added with the commit "mmc: checking
status after commands with R1b response". But the status register
returned from send status command of SPI protocol is different from
that of MMC/SD protocol. We do a simple test and generate a response
in stead of full bit-by-bit translation.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
2011-05-18 14:30:34 -05:00
Reinhard Meyer
329f0f52fa ATMEL: fix related common atmel driver files
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2011-05-18 07:56:51 +02:00
Andreas Bießmann
f4278b716c avr32: fixup definitions to ATMEL_BASE_xxx
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
2011-05-18 07:56:50 +02:00
Andreas Bießmann
5d73bc7af7 avr32: rename memory-map.h -> hardware.h
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
2011-05-18 07:56:50 +02:00
Jason Liu
4571de33ee fsl_esdhc: Fix multi-block read restriction on i.MX53 eSDHCv2
For freescale i.MX53 eSDHCv2, when using CMD12, cmdtype need
to be set to ABORT, otherwise, next read command will hang.

This is a software Software Restrictions in i.MX53 reference manual:

29.7.8 Multi-block Read
For pre-defined multi-block read operation, that is,the number of blocks
to read has been defined by previous CMD23 for MMC, or pre-defined number
of blocks in CMD53 for SDIO/SDCombo,or whatever multi-block read without
abort command at card side, an abort command, either automatic or manual
CMD12/CMD52, is still required by ESDHC after the pre-defined number of
blocks are done, to drive the internal state machine to idle mode. In this
case, the card may not respond to this extra abort command and ESDHC will
get Response Timeout.  It is recommended to manually send an abort command
with RSPTYP[1:0] both bits cleared.

Signed-off-by: Jason Liu <jason.hui@linaro.org>
2011-04-29 03:22:17 -05:00
John Rigby
4ca9244d74 MMC: omap_hsmmc.c: disable multiblock rw on old rev omap34xx silicon
Signed-off-by: John Rigby <john.rigby@linaro.org>
2011-04-29 03:22:17 -05:00
John Rigby
8feafcc49c MMC: make b_max unconditional
Make existing field b_max field in struct mmc unconditional
and use it instead of CONFIG_SYS_MMC_MAX_BLK_COUNT in mmc_bread
and mmc_bwrite.

Initialize b_max to CONFIG_SYS_MMC_MAX_BLK_COUNT in mmc_register
if it has not been initialized by the hw driver.

Initialize b_max to 0 in all callers to mmc_register.

Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2011-04-29 03:21:54 -05:00
Matt Waddel
23b93e1d66 MMC: Add support for PL180 ARM mmc device
Add support for the ARM PrimeCell MultiMedia Interface - PL180.
Ported from original device driver written by ST-Ericsson.

Signed-off-by: Matt Waddel <matt.waddel@linaro.org>
2011-04-29 03:20:01 -05:00
Raffaele Recalcati
8511cd84ab MMC may wrongly regconize 2GB eMMC as high capacity
Hi Terry,

> So I guess:
> mmc_init calls mmc_send_op_cond  that set  high_capacity,
> than it calls mmc_startup, that, with MMC_CMD_SEND_CSD  command, set
> the capacity, using values in CSD register.
> So I guess that mmc_change_freq should not recalculate high_capacity.
>
> It seems better, isn't it?
>
> Regards,
> Raffaele
>

Finally I think that it is enough to apply the following patch in order
to fix the issue.

Regards,
Raffaele

Signed-off-by: Andy Fleming <afleming@freescale.com>
2011-04-13 07:09:04 -05:00
Raffaele Recalcati
5db2fe3ad9 mmc: trace added
Defining CONFIG_MMC_TRACE in the include board file it is possible to activate
a tracing support.
This code helps in case of eMMC hw failure or to investigate possible eMMC
initialization issues.

Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2011-04-13 07:09:04 -05:00
Raffaele Recalcati
31cacbabf0 mmc: SEND_OP_COND considers card capabilities (voltage)
The first SEND_OP_COND (CMD1) command added is used to ask card capabilities.
After it an AND operation is done between card capabilities and host
capabilities (at the moment only for the voltage field).
Finally the correct value is sent to the MMC, waiting that the card
exits from busy state.

Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2011-04-13 07:09:04 -05:00
Raffaele Recalcati
5d4fc8d907 mmc: checking status after commands with R1b response
It is recommended to check card status after these kind of commands.
This is done using CMD13 (SEND_STATUS) JEDEC command until
the card is ready.
In case of error the card status field is displayed.

Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2011-04-13 07:08:57 -05:00
Minkyu Kang
8baf939c2c mmc: remove duplicated header file
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2011-04-13 06:36:15 -05:00
Thomas Chou
d52ebf1022 mmc: add generic mmc spi driver
This patch supports mmc/sd card with spi interface. It is based on
the generic mmc framework. It works with SDHC and supports multi
blocks read/write.

The crc checksum on data packet is enabled with the def,

There is a subcomamnd "mmc_spi" to setup spi bus and cs at run time.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2011-04-13 06:35:22 -05:00
Mike Frysinger
5f837c2c0e mmc: constify & localize data
These local vars need not be writable nor exported.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2011-04-13 06:35:22 -05:00
Frans Meulenbroeks
63fb5a7e4b drivers/mmc/fsl_esdhc.c: reordered tests
As DATA_ERROR includes the value IRQSTAT_DTOE, a timeout error
would yield the first error return instead of TIMEOUT.
By swapping the test TIMEOUTs are reported as such

An alternate solution would be to remove the IRQSTAT_DTOE from the DATA_ERROR define
but as that one might be less desired I've opted for the simplest solution

Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2011-04-13 06:35:22 -05:00
Matt Waddel
ce0fbcd2e1 MMC: Max blocks value adjustable
The maximum blocks value was hardcoded to 65535 due to a 16 bit
register length.  The value can change for different platforms.
This patch makes the default the current value of 65535, but it
is configurable for other platforms.

Signed-off-by: Matt Waddel <matt.waddel@linaro.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2011-04-13 06:35:22 -05:00
Alagu Sankar
b44c70837a SD1.00 wide-bus fix
Fixed a bug wherein SD version 1.0 cards were not configured for 4-bit mode

Signed-off-by: Alagu Sankar <alagusankar@embwise.com>
2011-04-13 03:50:43 -05:00
Wolfgang Denk
17e967b3df Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2011-04-10 21:24:40 +02:00
Priyanka Jain
32c8cfb23c fsl_esdhc: Deal with watermark level register related changes
P1010 and P1014 has v2.3 version of FSL eSDHC controller in which watermark
level register description has been changed:

9-15 bits represent WR_WML[0:6], Max value = 128 represented by 0x00
25-31 bits represent RD_WML[0:6], Max value = 128 represented by 0x00

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-10 11:17:55 -05:00
Sonic Zhang
21a50374d5 Blackfin: bfin_sdh: add support for multiblock operations
Don't forget to count full data size for the multiblock operation request.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08 00:44:27 -04:00
Cliff Cai
1fd2d792a2 Blackfin: bfin_sdh: set all timer bits before transfer
The timer register is 32bits, not 16bit, so 0xFFFF won't fill it.
Write out -1 to make sure to fill the whole thing.

Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08 00:44:27 -04:00
Mike Frysinger
cca07417d5 Blackfin: BF50x: new processor port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08 00:44:26 -04:00
Chander Kashyap
f69bb51145 S5P: mmc: Resolved interrupt error during mmc_init
Blocksize was hardcoded to 512 bytes. But the blocksize varies
depeding on various mmc subsystem commands (between 8 and 512).
This hardcoding was resulting in interrupt error during data
transfer.

It is now calculated based upon the request sent by mmc subsystem.

Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2011-03-27 19:20:26 +02:00
Priyanka Jain
b71ea33699 fsl_esdhc: Correcting esdhc timeout counter calculation
- Timeout counter value is set as DTOCV bits in SYSCTL register
  For counter value set as timeout,
  Timeout period = (2^(timeout + 13)) SD Clock cycles

- As per 4.6.2.2 section of SD Card specification v2.00, host should
  cofigure timeout period value to minimum 0.25 sec.

- Number of SD Clock cycles for 0.25sec should be minimum
	(SD Clock/sec * 0.25 sec) SD Clock cycles
	= (mmc->tran_speed * 1/4) SD Clock cycles

- Calculating timeout based on
	(2^(timeout + 13)) >=  mmc->tran_speed * 1/4
	Taking log2 both the sides and rounding up to next power of 2
	=> timeout + 13 = log2(mmc->tran_speed/4) + 1

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-03-07 08:49:28 -06:00
Kumar Gala
5103a03a0b fsl_esdhc: Add the workaround for erratum ESDHC-A001 (enable on P2020)
Data timeout counter (SYSCTL[DTOCV]) is not reliable for values of 4, 8,
and 12. Program one more than the desired value: 4 -> 5, 8 -> 9, 12 -> 13.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-03 02:46:12 -06:00
Wolfgang Denk
d1a24f0618 Minor Coding Style Cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-02-02 22:36:10 +01:00
Sandeep Paulraj
57418d2139 Davinci MMCSD Support
Added support for MMC/SD cards for Davinci.  This feature is enabled by
CONFIG_DAVINCI_MMC and is dependant on CONFIG_MMC and CONFIG_GENERIC_MMC
options. This is tested on DM355 and DM365 EVMs with both the available mmc
controllers.

Signed-off-by: Alagu Sankar <alagusankar@embwise.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-02-02 00:54:44 +01:00
Roy Zang
3b4456ec39 fsl_esdhc: Add the workaround for erratum ESDHC135 (enable on P4080)
The default value of the SRS, VS18 and VS30 and ADMAS fields in the host
controller capabilities register (HOSTCAPBLT) are incorrect. The default
of these bits should be zero instead of one.

Clear these bits out when we read HOSTCAPBLT.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:22 -06:00
Jerry Huang
d621da0066 fsl_esdhc: Add the workaround for erratum ESDHC111 (enable on P4080)
Do not issue a manual asynchronous CMD12. Instead, use a (software)
synchronous CMD12 or AUTOCMD12 to abort data transfer.

Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:22 -06:00
Chenhui Zhao
a6da8b8195 fsl_esdhc: Fix esdhc disabled problem on some platforms
Some new platform's esdhc pins don't share with other function.
The eSDHC shouldn't be disabled, even if "esdhc" isn't defined
in hwconfig env variable.

Use CONFIG_FSL_ESDHC_PIN_MUX to fix this problem.

Signed-off-by: Chenhui Zhao <b26998@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:19 -06:00
Li Yang
030955c2ca fsl_esdhc: Fix the voltage validation process
The current code use all the voltage range support by the host
controller to do the validation.  This will cause problem when
the host supports Low Voltage Range.  Change the validation
voltage to be based on board setup.

Signed-off-by: Li Yang <leoli@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-12-18 23:15:24 +01:00
Jerry Huang
63786d299d fsl_esdhc: Fix max clock frequency
The max clock of MMC is 52MHz

Signed-off-by: Jerry Huang <Changm-Ming.Huang@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-12-18 23:15:24 +01:00
Jerry Huang
4a6ee172c3 fsl_esdhc: Use mmc_set_clock to set initial speed
After booting the u-boot, and first using some SD card (such as Sandisk 2G SD
card), because the field 'clock' of struct mmc is zero, this will cause
the read transfer is always active and SDHC DATA line is always active,
therefore, driver can't handle the next command.

Therefore, we use mmc_set_clock to setup both the data structure and HW
to the initial clock speed of 400000Hz.

Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-12-18 23:15:21 +01:00
P.V.Suresh
2c1764efc2 fsl_esdhc: Set the eSHDC DMACTL[SNOOP] bit after resetting the controller
eSDHC host controller reset results in clearing of snoop bit also.
This patch sets the SNOOP bit after the completion of host controller reset.
Without this patch mmc reads are not consistent.

Signed-off-by: P.V.Suresh <pala@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-12-13 09:32:16 -06:00
Reinhard Meyer
2aed9d14cc AT91: gen_atmel_mci.c: fix bug when Slot B is used
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-12-07 16:36:39 +01:00
Nishanth Menon
eb9a28f699 mmc: omap: timeout counter fix
Having a loop with a counter is no timing guarentee for timing
accuracy or compiler optimizations. For e.g. the same loop counter
which runs when the MPU is running at 600MHz will timeout in around
half the time when running at 1GHz. or the example where GCC 4.5
compiles with different optimization compared to GCC 4.4. use timer
to keep track of time elapse and we use an emperical number - 1sec
for a worst case timeout.  This should never happen, and is adequate
imaginary condition for us to fail with timeout.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-19 16:27:37 -05:00
Sebastien Carlier
6d8962e814 Switch from archive libraries to partial linking
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils.  As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".

This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.

The name of each former library archive is preserved except for
extensions which change from ".a" to ".o".  This commit updates
references accordingly where needed, in particular in some linker
scripts.

This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols.  Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.

Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
2010-11-17 21:02:18 +01:00
Alagu Sankar
4a1a06bc8b mmc: Add multi-block read support to the generic mmc driver
This patch adds multi-block read support for the generic MMC
driver. Large reads are broken into chunks of 65535 blocks to
ensure that the code works with controllers having a 16 bit block counter.

This patch results in a significant performance improvement.

Time to read a 45 MB file went from 36 seconds to 9 seconds on Overo

Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Tested-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-04 15:27:25 -04:00
Steve Sakoman
def412b661 mmc: Clean up generic mmc driver multi-block write functions
The current mmc write implementation is type ulong, but returns int values.
Some of the printf's are terminated with /n/r, one has none.

This patch fixes these issues and also removes some unnecessary local
variables.

Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-04 15:27:21 -04:00
Wolfgang Denk
17dd883c5b Merge branch 'master' of git://git.denx.de/u-boot-samsung 2010-10-29 21:47:48 +02:00
Wolfgang Denk
071bc92330 Coding Style cleanup
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-27 22:48:30 +02:00
Lei Wen
0158126e25 mmc: seperate block number into small parts for multi-write cmd
Constraint the mmc framework to only send no more than 65535
blocks in one go during the multi-write command. This constraint
comes due to the limitation of 16bit width block counter register
at some hardware.

Signed-off-by: Lei Wen <leiwen@marvell.com>
Cc: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-10-27 20:39:33 +02:00
Marek Vasut
3ba8bf7c6d PXA: pxa-regs.h cleanup
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2010-10-19 22:46:22 +02:00
Jaehoon Chung
1727e21698 s5p_mmc: support 8-bit bus width
This Patch do support 8-bit bus width for s5p
So we add parameter for bus_width (in s5p_mmc_init(), s5p_mmc_initialize())
If want to use 8-bit bus width, only change (0, 8) instead of (0, 4).

 Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
 Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
 Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2010-10-19 11:34:54 +09:00
Sukumar Ghorai
de941241a0 ARMV7: OMAP: Add new mmc driver compatible with CONFIG_GENERIC_MMC
OMAP boards currently use a legacy mmc driver. This patch adds a new
mmc driver which will work with the generic mmc driver in u-boot.

This new driver will work with both OMAP3 and OMAP4 boards.

This patch does not remove the old driver.  It should remain in the
tree until all boards that use it switch to the new driver.

Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
2010-10-17 20:14:10 +02:00
Sukumar Ghorai
d23e2c09a7 MMC: Fix for capacity calculation on eMMC
The current mmc driver returns erroneous capacity information for
  eMMC.  The capacity of eMMC devices is available only in the ext-CSD
  register.  This patch add code to read the ext-CDSD register and
  correctly calculate eMMC capacity.

Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Acked-by: Steve Sakoman <steve@sakoman.com>
2010-10-17 20:14:06 +02:00
Mike Frysinger
6815f540db Blackfin: bfin_sdh: clean up send_cmd
Simplify the command setup and status checking steps, and add a proper
timeout to the status polling code to avoid possible infinite hangs.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02 16:00:37 -04:00
Wolfgang Denk
fe64fd4238 mmc: fix compiler warnings
Commit d2bf29e3 caused a number of compiler warnings:

mmc.c: In function 'mmc_bwrite':
mmc.c:97: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'long unsigned int'
mmc.c:97: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'lbaint_t'
mmc.c: In function 'mmc_bread':
mmc.c:229: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'long unsigned int'
mmc.c:229: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'lbaint_t'

Fix these.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Lei Wen <leiwen@marvell.com>
2010-09-19 12:30:54 +02:00
Lei Wen
d2bf29e399 mmc: add boundary check for mmc operation
Signed-off-by: Lei Wen <leiwen@marvell.com>
2010-09-18 23:46:24 +02:00
Wolfgang Denk
cf64fda38e Merge branch 'at91' of git://git.denx.de/u-boot-atmel 2010-09-08 00:42:00 +02:00
Wolfgang Denk
09b4a9cf40 Merge branch 'master' of git://git.denx.de/u-boot-samsung 2010-09-08 00:03:22 +02:00
Reinhard Meyer
1592ef8596 AT91: MCI: add SD/MMC driver using mmc framework
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-09-03 11:19:01 +02:00
Minkyu Kang
d93d0f0cfe S5P: Use accessor functions instead of SoC specific defines to access the base address
This patch is intended to prepare the other S5P SoC. (s5pc210)
If use SoC specific defines then can't share with other SoC.
So, make the accessor functions for access the base address by common way.

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2010-08-17 11:38:19 +09:00
Grazvydas Ignotas
dc41b8bf3d mmc: omap3: fix block read function
The OMAP3 block read function is not following API and always returning
1 instead of read block count, fix it. Also to simplify code, merge it
with with a helper function, which was only called from the block read
function.

After this patch ext2 filesystem can be used properly.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-08-12 13:50:25 -04:00
Grazvydas Ignotas
8bbf4307c7 mmc: omap3: make local symbols static
Make driver local variables and functions static and
remove them from the arch header.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-08-12 13:50:19 -04:00
Minkyu Kang
6a69e11a79 S5P: mmc: use the standard debug macro
Use the standard debug macro instead of the costom macro

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Wolfgang Denk <wd@denx.de>
2010-08-10 13:42:23 +09:00
Wolfgang Denk
9efac4a1eb Merge branch 'master' of git://git.denx.de/u-boot-samsung 2010-08-04 00:35:10 +02:00
Minkyu Kang
5000284872 S5P: support mmc driver
This patch adds support mmc driver for s5p SoC

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2010-08-03 10:18:15 +09:00
Wolfgang Denk
93502a5e0a Merge branch 'master' of ../master 2010-07-15 22:48:46 +02:00
Mike Frysinger
a87589fcf9 Blackfin: bfin_sdh: convert to portmux framework
Rather than bang MMRs directly, use the new portmux framework to handle
the details.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-07-13 17:50:49 -04:00
Steve Sakoman
89716964d9 mmc: add function prototype for mmc_set_dev in mmc.h
this eliminates compiler warnings when cmd_mmc.c is built with CONFIG_SYS_MMC_SET_DEV

the mmc_set_dev implementation in omap3_mmc.c is also tweaked to match
the new prototype in parameter naming and type

Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-07-05 20:00:32 -04:00
Steve Sakoman
bec3dc7599 ARMV7: Restructure OMAP mmc driver to allow code sharing between OMAP3 and OMAP4
The architecture independent header is moved to drivers/mmc, and the architecture
dependent headers reside in asm/arch-omap3 and asm/arch-omap4

Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-07-05 20:00:05 -04:00
Steve Sakoman
8f22327a66 OMAP: mmc: add support for second and third mmc channels
This patch adds support for the second and third mmc channels on OMAP3
processors

Boards wishing to use this feature should define CONFIG_SYS_MMC_SET_DEV
in the board config

Tested on Overo

Signed-off-by: Steve Sakoman <steve@sakoman.com>
Tested-by: Philip Balister <philip@opensdr.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-07-05 19:59:49 -04:00
Marek Vasut
43c15d3dd5 PXA: PXAMMC: Add Monahans support
This patch enables PXAMCI support on PXA3xx CPUs. This patch only enables MMC1
though, MMC2 and PXA31x MMC3 will need further patch to be operational.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2010-06-13 13:39:11 +02:00
Marek Vasut
55429a0323 PXA: PXAMMC: Drop different delays for PXA27X
In case the delays were set to 10000, the MMC card on PXA27X boards (and PXA3xx
boards) didn't initialize on first try. Increasing the delays and leaving just
those for PXA25x and 26x (that is 200000) fixes this problem.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2010-06-13 13:39:11 +02:00
Wolfgang Denk
7b43db9211 drivers/mmc/fsl_esdhc.c: fix compiler warnings
Commit 77c1458d caused the following compiler warnings:

fsl_esdhc.c: In function 'esdhc_pio_read_write':
fsl_esdhc.c:142: warning: assignment discards qualifiers from pointer target type
fsl_esdhc.c: In function 'esdhc_setup_data':
fsl_esdhc.c:169: warning: unused variable 'wml_value'
fsl_esdhc.c: In function 'esdhc_pio_read_write':
fsl_esdhc.c:164: warning: control reaches end of non-void function

Fix these.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Dipen Dudhat <dipen.dudhat@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
2010-05-15 19:47:17 +02:00
Dipen Dudhat
77c1458d13 ppc/85xx: PIO Support for FSL eSDHC Controller Driver
On some Freescale SoC Internal DMA of eSDHC controller has bug.
So PIO Mode has been introduced to do data transfer using CPU.

Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
2010-04-23 21:02:30 -05:00
Roy Zang
ab467c512e fsl_esdhc: Only modify the field we are changing in WML
When we set the read or write watermark in WML we should maintain the
rest of the register as is, rather than using some hard coded value.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-07 00:01:11 -05:00
Jerry Huang
48bb3bb5ac fsl_esdhc: Add function to reset the eSDHC controller
To support multiple block read command we must set abort or use auto
CMD12.  If we booted from eSDHC controller neither of these are used
and thus we need to reset the controller to allow multiple block read
to function.

Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-07 00:01:11 -05:00
Kumar Gala
cc4d122658 fsl_esdhc: Always stop clock before changing frequency
We need to stop the clocks on 83xx/85xx as well as imx.  No need to make
this code conditional to just imx.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Stefano Babic <sbabic@denx.de>
2010-04-07 00:01:11 -05:00
Stefano Babic
99c006a320 mxcmmc: fix warnings due to access 32 bit registers with 16 bit accessors
Some registers of the mxcmmc driver were accessed using
16 bit accessor functions, because only the LSB is
significant. This is not needed and generates
warnings.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-03-21 22:22:52 +01:00
Wolfgang Denk
8c4444ff5e Fix memory leak in mmc_read()
There is be a path through mmc_read in drivers/mmc/mmc.c where
malloc'd memory is not freed before exiting mmc_read: it occurs if
mmc_set_blocklen() returns a non-zero value.

Reported-by: Quentin Armitage <Quentin@Armitage.org.uk>
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-03-11 23:35:43 +01:00
Stefano Babic
c67bee1460 fsl_esdhc: add support for mx51 processor
The esdhc controller in the mx51 processor is quite
the same as the one in some powerpc processors
(MPC83xx, MPC85xx). This patches adapts the driver
to support the arm mx51.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-03-07 12:36:36 -06:00
Stefano Babic
11fdade294 MMC: add weak function to detect MMC/SD card
Most controllers can check if there is a card in the slot.
However, they require pins that could be not available because
required by other functions and the detection of a card must
be performed in another way. This patch adds a weak function
that a board can implement to add its internal custom way
to check the presence of a MMC/SD card.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-03-07 12:36:36 -06:00
Stefano Babic
250de12bc2 mmc: check correctness of the voltage mask in ocr
Most cards do not answer if some reserved bits
in the ocr are set. However, some controllers
can set bit 7 (reserved for low voltages), but
how to manage low voltages SD card is not yet
specified.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-03-07 12:36:36 -06:00
Cliff Cai
e54c820991 Blackfin: convert bfin_sdh to generic mmc
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-01-17 09:17:27 -05:00
Vaibhav Hiremath
7c15121f40 omap3_mmc: Encapsulate twl4030 under option CONFIG_TWL4030_POWER
Fixes the build/compilation error if we try to re-use the omap3_mmc code
without TWL4030_POWER.

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
2009-11-27 16:26:18 -06:00
Dirk Behme
9de0212bd7 OMAP3 MMC: Fix warning dereferencing type-punned pointer
Fix warning
Dereferencing type-punned pointer will break strict-aliasing rules

Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
CC: Steve Sakoman <sakoman@gmail.com>
Acked-by: Tom Rix <Tom.Rix@windriver.com>
2009-10-13 06:17:36 -05:00
Wolfgang Denk
53cc18c71b Minor coding style cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-08-10 10:38:34 +02:00
Ilya Yanok
ba3dbaf281 mxc-mmc: sdhc host driver for MX2 and MX3 proccessor
This is a port of Linux driver for SDHC host controller hardware
found on Freescale's MX2 and MX3 processors. Uses new generic MMC
framework (CONFIG_GENERIC_MMC) and it looks like there are some
problems with a framework (at least on LE cpus). Some of these
problems are addressed in the following patches.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
2009-08-09 23:47:38 +02:00
Tom Rix
fccc0fcaaa OMAP3 Move twl4030 mmc function
Because twl4030 now has its own device files, move and rename
twl4030_mmc_config.

twl4030_mmc_config initializes the twl4030 power setting to
the mmc device.  Because it is in the twl4030 power domain, move
it out of drivers/mmc/omap3_mmc.c and into drivers/power/twl4030.c.

The function was renamed to twl4030_power_mmc_init because all
the functions in this file are to have the format

twl4030_power_<device>_<action>

In this case the suffix is mmc_init so
device : mmc
action : init

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
2009-07-29 09:57:43 +02:00
Ilya Yanok
b86b85e261 mmc: set bus width to 1 and clock to minimum early during initialization
We need to switch back to 1-bit before initialization or SD 2.0 cards
will fail to send SCR if we've switched to 4-bit already.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
2009-07-19 22:07:29 +02:00
Anton Vorontsov
b33433a63f fsl_esdhc: Add device tree fixups
This patch implements fdt_fixup_esdhc() function that is used to fixup
the device tree.

The function adds status = "disabled" propery if esdhc pins muxed away,
otherwise it fixups clock-frequency for esdhc nodes.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
2009-07-16 22:24:06 +02:00
Yauhen Kharuzhy
4e3d89ba94 mmc: Fix decoding of SCR & function switch data on little-endian machines
SCR & switch data are read from card as big-endian words and should be
converted to CPU byte order.

Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2009-06-02 17:20:04 -05:00
Yauhen Kharuzhy
f33cb34b39 mmc: Remove return from mmc_init for non SD 2.0 compatible cards.
Cards which are not compatible with SD 2.0 standard, may return response
for CMD8 command, but it will be invalid in terms of SD 2.0. We should
accept this case as admissible, just like Linux does.

Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2009-06-02 17:19:07 -05:00
Rabin Vincent
998be3dd59 mmc: drop unnecessary casts
Now that response is a uint, we can drop all the casts.

Signed-off-by: Rabin Vincent <rabin@rab.in>
2009-06-02 17:18:57 -05:00
Rabin Vincent
0b453ffe28 mmc: fix response decoding on little endian
The mmc code defines the response as an array of chars.  However, it
access the response bytes both as (i) an array of four uints (with
casts) and (ii) as individual chars.  The former case is used more
often, including by the driver when it assigns the response.

The char-wise accesses are broken on little endian systems because they
assume that the bytes in the uints are in big endian byte order.

This patch fixes this by changing the response to be an array of four
uints and replacing the char-wise accesses with equivalent uint-wise
accesses.

Signed-off-by: Rabin Vincent <rabin@rab.in>
2009-06-02 17:18:57 -05:00
Rabin Vincent
9b1f942c09 mmc: use lldiv to fix arm eabi build
The generic MMC core uses direct long long divisions, which do not build
with ARM EABI toolchains.  Use lldiv() instead, which works everywhere.

Signed-off-by: Rabin Vincent <rabin@rab.in>
2009-06-02 17:18:56 -05:00
Rabin Vincent
e85649c7e6 mmc: check find_mmc_device return value
find_mmc_device returns NULL if an invalid device number is specified.
Check for this to avoid dereferencing NULL pointers.

Signed-off-by: Rabin Vincent <rabin@rab.in>
2009-06-02 17:18:56 -05:00
Peter Tyser
f9a109b3ad Replace __attribute references with __attribute__
__attribute__ follows gcc's documented syntax and is generally more
common than __attribute.  This change is only asthetic and should not
affect functionality.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-04-28 01:01:39 +02:00
Mike Frysinger
d3c38d96b9 Blackfin: convert bfin_sdh to legacy mmc
The Blackfin SDH controller is still using the legacy framework, so update
the driver to use the renamed functions.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02 06:42:05 -04:00
Dirk Behme
aba45c85b2 OMAP3: Clean up MMC code
Clean up OMAP3 MMC code:

* Convert register access to struct & readx/writex style
* Replace hardcode values by macros
* Remove macro defined twice

Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-02-22 18:29:10 +01:00
Wolfgang Denk
09fee8e867 Coding Style cleanup; update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-02-22 01:19:52 +01:00
Tom Rix
e3ba7f137c ARM:PXA Use new definitions in mmc.h
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-20 03:47:50 +01:00
Andy Fleming
682beeac34 Reduce the scope of PXA's mmc_read/mmc_write/mmc_bread functions
These names are being taken over by the new MMC framework.  Hopefuly
the PXA can be easily ported, and these functions will go away entirely.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-20 03:47:50 +01:00
Jean-Christophe PLAGNIOL-VILLARD
b03d92e558 pxa: move mmc drivers to drivers/mmc
introduce new macro CONFIG_PXA_MMC to activate it

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-20 03:47:50 +01:00
Tom Rix
e5e88c3614 ARM:OMAP3 Change mmc_init to mmc_legacy_init
omap3_mmc.c was changed to define mmc_legacy_init.
Remove unused functions.

Compile tested on all arm
Runtime tested on Zoom1.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-02-19 23:50:33 +01:00
Andy Fleming
50586ef24e Add support for the Freescale eSDHC found on 8379 and 8536 SoCs
This uses the new MMC framework

Some contributions by Dave Liu <daveliu@freescale.com>

Signed-off-by: Andy Fleming <afleming@freescale.com>
2009-02-16 18:07:42 -06:00
Andy Fleming
272cc70b21 Add MMC Framework
Here's a new framework (based roughly off the linux one) for managing
MMC controllers.  It handles all of the standard SD/MMC transactions,
leaving the host drivers to implement only what is necessary to
deal with their specific hardware.

This also hooks the infrastructure into the PowerPC board code
(similar to how the ethernet infrastructure now hooks in)

Some of this code was contributed by Dave Liu <daveliu@freescale.com>

Signed-off-by: Andy Fleming <afleming@freescale.com>
2009-02-16 18:07:41 -06:00
Andy Fleming
abb5466ccf Convert mmc_init to mmc_legacy_init
This is to get it out of the way of incoming MMC framework

Signed-off-by: Andy Fleming <afleming@freescale.com>
2009-02-16 18:07:40 -06:00
Andy Fleming
b2e2ed0233 Eliminate support for using MMC as memory
MMC cards are not memory, so we stop treating them that way.

Signed-off-by: Andy Fleming <afleming@freescale.com>
2009-02-16 18:07:40 -06:00
Cliff Cai
716ebf436c Blackfin: add driver for on-chip MMC/SD controller
This is a port of the Linux Blackfin on-chip SDH driver to U-Boot.

Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-02-02 12:27:18 -05:00
Dirk Behme
b1c3bf99fb OMAP3: Add MMC support
Add MMC support.

Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-01-24 17:51:22 +01:00
Jean-Christophe PLAGNIOL-VILLARD
6d0f6bcf33 rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-10-18 21:54:03 +02:00
Stefan Roese
f2302d4430 Fix merge problems
Signed-off-by: Stefan Roese <sr@denx.de>
2008-08-06 14:05:38 +02:00
Haavard Skinnemoen
c3bf1ad7ba mmc: Move atmel_mci driver into drivers/mmc
This makes it easier to use the driver on other platforms.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Jean-Chritophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-07-10 00:05:52 +02:00
Haavard Skinnemoen
5ce13051a4 Create drivers/mmc subdirectory
In order to consolidate more of the various MMC drivers around the
tree, we must first have a common place to put them.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Jean-Chritophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-07-10 00:02:36 +02:00