The Andes PLMT driver directly accesses the mtime MMIO region,
indicating its intended use in the M-mode boot stage. However,
since U-Boot proper (S-mode) also uses the PLMT driver, we need
to specifically mark the region as readable through PMPCFGx (or
S/U-mode read-only shared data region for Smepmp) in OpenSBI.
Granting permission for this case doesn't make sense. Instead,
we should use the generic RISC-V timer driver to read the mtime
through the TIME CSR. Therefore, we add the SPL_ANDES_PLMT_TIMER
config, which ensures that the PLMT driver is linked exclusively
against M-mode U-Boot or U-Boot SPL binaries.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Most boards don't enable the pre-console buffer. So we will not see any
early messages. OpenSBI 1.3 provides us with the debug console extension
that can fill this gap.
For S-Mode U-Boot enable CONFIG_DEBUG_UART by default.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Below warning can be occurred when CONFIG_BOOTSTAGE and
!CONFIG_SPL_BOOTSTAGE. It should be guarded by using CONFIG_IS_ENABLED
for SPL build.
arch/riscv/lib/bootm.c:46:9: warning: implicit declaration of
function 'bootstage_report'
46 | bootstage_report();
| ^~~~~~~~~~~~~~~~
| bootstage_error
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Multiple revisions of the StarFive VisionFive 2 board exist. They can be
identified by reading their EEPROM.
Linux uses two differently named device-tree files. To load the correct
device-tree we need to set $fdtfile to the device-tree file name that
matches the board revision.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Tested-by: Milan P. Stanić <mps@arvanta.net>
This old patch was marked as deferred. Bring it back to life, to continue
towards the removal of common.h
Move this out of the common header and include it only where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Remember where these end up so that we can pass this information on to
the EFI layer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The StarFive VisionFive 2 board cannot load spl/u-boot-spl.bin but needs a
prefixed header. We have referring to a vendor tool (spl_tool) for this
task. 'mkimage -T sfspl' can generate the prefixed file.
Use binman to invoke mkimage for the generation of file
spl/u-boot-spl.bin.normal.out.
Update the documentation.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Tested-by: Milan P. Stanić <mps@arvanta.net>
Multiple revisions of the StarFive VisionFive 2 board exist. They can be
identified by reading their EEPROM.
Linux uses two differently named device-tree files. To load the correct
device-tree we need to set $fdtfile to the device-tree file name that
matches the board revision.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
With having both an EVENT_SPY_SIMPLE setup for both riscv_cpu_probe and
riscv_cpu_setup we do not need the latter function to call the former
function as it will already have been done in time.
Fixes: 1c55d62fb9 ("riscv: cpu: make riscv_cpu_probe to EVT_DM_POST_INIT_R callback")
Tested-by: Milan P. Stanić <mps@arvanta.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
This function should now be a EVENT_SPY_SIMPLE call, update it.
Tested-by: Milan P. Stanić <mps@arvanta.net>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The DBCN extension provides a Console Write Byte call.
Implement function sbi_dbcn_write_byte to invoke it.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Starfive JH7110 needs to clear L2 LIM to zero before use or ECC error
would be triggered. Currently, we use DDR ram for SPL malloc arena on
Visionfive 2 board in defconfig, but it's also possible to use L2 LIM as
SPL malloc arena. To avoid triggering ECC error in this scenario, we
imply SPL_SYS_MALLOC_CLEAR_ON_INIT as default.
Signed-off-by: Bo Gan <ganboing@gmail.com>
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The JH7110 has the arhitectural CPU timer on all 5 rv64 cores.
Note that in the device tree.
Signed-off-by: Torsten Duwe <duwe@suse.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Very few of the existing event-spy records use the arguments they are
passed. Update them to use a simple spy instead, to simplify the code.
Where an adaptor function is currently used, remove it where possible.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since the Patch 55171aedda, VisionFive2 booting has been broken [1].
VisionFive2 board requires to enable CONFIG_TIMER_EARLY but booting went
to panic from initr_dm_devices due to lack of a timer device.
- Error logs
initcall sequence 00000000fffd8d38 failed at call 00000000402185e4
(err=-19)
Thus, we need to move riscv_cpu_probe function in order to register
the timer earlier than initr_dm_devices.
Fixes: 7fe32b3442 ("event: Convert arch_cpu_init_dm() to use events")
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Tested-by: Milan P. Stanić <mps@arvanta.net>
Tested-by: Roland Ruckerbauer <mail@ruabmbua.dev>
Tested-by: Roland Ruckerbauer <mail@ruabmbua.dev>
board_get_usable_ram_top() returns a physical address that is stored in
gd->ram_top. The return type of the function should be phys_addr_t like the
current type of gd->ram_top.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add Kconfig item for Starfive JH7110 to select SPL_ZERO_MEM_BEFORE_USE.
Signed-off-by: Bo Gan <ganboing@gmail.com>
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add the actual support code for SPL_ZERO_MEM_BEFORE_USE and remove
existing Starfive JH7110's L2 LIM clean code, since existing code has
following issues:
1. Each hart (in the middle of a function call) overwriting its own
stack and other harts' stacks.
(data-race and data-corruption)
2. Lottery winner hart can be doing "board_init_f_init_reserve",
while other harts are in the middle of zeroing L2 LIM.
(data-race)
Signed-off-by: Bo Gan <ganboing@gmail.com>
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add a Kconfig item to allow SPL to clear stack/GD/malloc area before
using them.
Signed-off-by: Bo Gan <ganboing@gmail.com>
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Some device driver need SYS_CACHELINE_SIZE macro. Add StarFive
SYS_CACHE_SHIFT_6 to enable it.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
In StarFive VF2 board. pcie0 connect to VTI usb controller.
Enable it to support usb host.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The pci_mmc.c driver can generate ACPI info and therefore includes
asm/acpi_table.h. This file does not exist for the RISC-V architecture
and thus code compilation fails when using this driver on RISC-V
Create an empty include file.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The USB 3.0 driver xhci-mem.c requires CONFIG_SYS_CACHELINE_SIZE to be set.
Define the cache line size for QEMU on RISC-V to be 64 bytes.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Harts need to use per-hart stack before any function call, even if that
function is a simple one. When the callee uses stack for register save/
restore, especially RA, if nested call, concurrent access by multiple
harts on the same stack will cause data-race.
This patch sets up SP before `board_init_f_alloc_reserve`. A side effect
of this is that the memory layout has changed as the following:
+----------------+ +----------------+ <----- SPL_STACK/
| ...... | | hart 0 stack | SYS_INIT_SP_ADDR
| malloc_base | +----------------+
+----------------+ | hart 1 stack |
| GD | +----------------+ If not SMP, N=1
+----------------+ | ...... |
| hart 0 stack | +----------------+
+----------------+ ==> | hart N-1 stack|
| hart 1 stack | +----------------+
+----------------+ | ...... |
| ...... | | malloc_base |
+----------------+ +----------------+
| hart N-1 stack| | GD |
+----------------+ +----------------+
| | | |
Signed-off-by: Bo Gan <ganboing@gmail.com>
Cc: Rick Chen <rick@andestech.com>
Cc: Leo <ycliang@andestech.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add support for Sipeed's Lichee Pi 4A board which based on T-HEAD's
TH1520 SoC, only minimal device tree and serial console are enabled,
so it's capable of chain booting from T-HEAD's vendor u-boot.
Reviewed-by: Wei Fu <wefu@redhat.com>
Signed-off-by: Yixun Lan <dlan@gentoo.org>
As the RISC-V ACLINT specification is defined to be backward compatible
with the SiFive CLINT specification, we rename SiFive CLINT to RISC-V
ALINT in the source tree to be future-proof.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Rick Chen <rick@andestech.com>
This RISC-V ACLINT specification [1] defines a set of memory mapped
devices which provide inter-processor interrupts (IPI) and timer
functionalities for each HART on a multi-HART RISC-V platform.
The RISC-V ACLINT specification is defined to be backward compatible
with the SiFive CLINT specification, however the device tree binding
is a new one. This change updates the sifive clint ipi driver to
support ACLINT mswi device, by checking the per-driver data field of
the ACLINT mtimer driver to determine whether a syscon based approach
needs to be taken to get the base address of the ACLINT mswi device.
[1] https://github.com/riscv/riscv-aclint/blob/main/riscv-aclint.adoc
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Rick Chen <rick@andestech.com>
StarFive VisionFive 2 has two versions, 1.2A and 1.3B, each version of
DDR capacity includes 2G/4G/8G, a DT can not support multiple
capacities, so the capacity size information is recorded to EEPROM, when
DDR initialization required capacity size information is read from
EEPROM.
If there is no information in EEPROM, it is initialized with the default
size defined in DT.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add support "atmel,24c04" eeprom for StarFive VisionFive2 board.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The difference between 1.2A and 1.3B is dynamically configured according
to the PCB version, and there is no difference on the board device tree,
so the same DT file can be used.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add ethernet device tree node to support StarFive ethernet driver for
the JH7110 RISC-V SoC.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
On some AE350 boards, we need to explicitly initialize the priority
registers to a non-zero value so the boot hart can instruct secondary
harts to jump to OpenSBI.
This patch also updates the information about PLICSW.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The "notable" disappearances are:
- the pac193x stanza - there's nothing in mainline linux w.r.t. bindings
for this & what is going to appear in mainline linux is going to be
incompatible with what is currently in U-Boot.
- operating points - these operating points should not be set at the
soc.dtsi level as they may not be possible depending on the design
programmed to the FPGA
- clock output names - there are defines for the clock indices, these
should not be needed
- the dt maintainers in linux NAKed using defines for IRQ numbers
- the qspi nand, which is not part of the icicle's default configuration
is removed.
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Tested-by: Padmarao Begari <padmarao.begari@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The original names picked for the DT doesn't match Linux's naming scheme
and it was renamed there a while ago. Rename it in U-Boot to allow
easily syncing dts between the two projects.
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
These seem to be missing, and trying to build ubifs without them
is causing errors due to these being missing.
Signed-off-by: Ben Dooks <ben.dooks@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add implementations of the local_irq_{save,restore} macros so that
<asm/atomic.h> can be used with riscv.
Signed-off-by: Ben Dooks <ben.dooks@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add a link from <asm/atomic.h> to the generic one to allow
things like ubifs to be built. This can be extended with
riscv AMO ops at a later date.
Signed-off-by: Ben Dooks <ben.dooks@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
OpenSBI already implements some extensions that are not ratified yet:
* Debug Console Extension (DBCN)
* System Suspend Extension (SUSP)
* Collaborative Processor Performance Control Extension (CPPC)
Allow the sbi command to display these.
Provide the FID definitions of the Debug Console Extension. We can use that
extension for an early debug console driver.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
In current linker script both .efi_runtime_rel and .rela.dyn sections
are of RELA type whose entry size is either 12 (RV32) or 24 (RV64).
These two are arranged as a continuous region on purpose so that the
prelink-riscv executable can fix up the PIE addresses in one loop.
However there is an 'ALIGN(8)' between these 2 sections which might
cause a gap to be inserted between these 2 sections to satisfy the
alignment requirement on RV32. This would break the assumption of
the prelink process and generate an unbootable image.
Fixes: 9a6569a043 ("riscv: Update alignment for some sections in linker scripts")
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Rick Chen <rick@andestech.com>
Add support to load the next stage image from an NVMe disk which may
be formatted as an EXT or FAT filesystem.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
[trini: Drop hunk changing disk/part.c as that breaks other users]
Signed-off-by: Tom Rini <trini@konsulko.com>
