The LCDIF Pixel clock mux is not glitchless, so need
to gate before changing mux.
Also change enable_lcdif_clock prototype with a new input
parameter to indicate disable or enable.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The mux for the lcd clock is not glitchless,
so need to first gate the clock before changing the mux.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
>From RM, per_periph2_clk_sel option3 is:
"derive clock from 198MHz clock (divided 392MHz PLL2 PFD)."
So fix it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add i.MX6SLL cpu type.
MXC_CPU_MX6D is not a real value in chip, so change it to 0x6A.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
liteBoard is a development board which uses liteSOM as its base.
Hardware specification:
* liteSOM (i.MX6UL, DRAM, eMMC)
* Ethernet PHY (id 0)
* USB host (usb_otg1)
* MicroSD slot (uSDHC1)
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
liteSOM is a System On Module (http://grinn-global.com/litesom/). It
can't exists on its own, but will be used as part of other boards.
Hardware specification:
* NXP i.MX6UL processor
* 256M or 512M DDR3 memory
* optional eMMC (uSDHC2)
Here we treat SOM similar to SOC, so we place it inside arch/arm/mach-*
directory and make it possible to reuse initialization code (i.e. DDR,
eMMC init) for all boards that use it.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
It's not necessary to define the processor in the defconfig file.
The preferred method to select the SoC is via Kconfig file.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
This adds board support for the Toradex module family Colibri iMX6.
The familiy consists of a module with i.MX6 DualLite, i.MX6 Solo, both
with a version for commercial and industrial temperature range.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
This adds board support for the Toradex module family Apalis iMX6.
The familiy consists of a module with i.MX6 Dual, i.MX6 Quad with
commercial and industrial temperature range.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Add proper reg values for the two AIPS bus nodes. This avoids this
two warnings:
Node /soc/aips-bus@40000000 has a unit name, but no reg property
Node /soc/aips-bus@40080000 has a unit name, but no reg property
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
A most basic PSCI implementation with only one psci_version is added for
LS1043A, this can verify the generic PSCI framework, and more platform specific
implementation will be added later.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Newly add ARMv8 PSCI needs to be initialized, be copied or reserved in right
place, this patch does all the setup steps.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch introduces a generic ARMv8 PSCI framework, with all functions
returning a dummy ARM_PSCI_RET_NI (Not Implemented), then it is up to each
platform to implement their own functions based on this framework.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
PSCI implementation needs the SMC instruction to be enabled.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds secure_text, secure_data and secure_stack sections for ARMv8 to
hold PSCI text and data, and it is based on the legacy implementation of ARMv7.
ARMV8_SECURE_BASE defines the address for PSCI secure sections, ARMV8_PSCI and
ARMV8_PSCI_NR_CPUS are firstly used in this patch, so they are introduce here
in Kconfig too.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
NXP/Freescale uses macro CONFIG_ARMV8_PSCI to enable their private PSCI
implementation in PPA firmware, but this macro naming too generic, so this
patch replaces it with a specic one CONFIG_FSL_PPA_ARMV8_PSCI.
And this macro CONFIG_ARMV8_PSCI will be used for a generic PSCI for ARMv8
which will be added in following patchs.
Signed-off-by: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The unit-address should be the same as the I2C address of the device.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Unlike Linux kernel, U-Boot depends on "spi-flash" compatible to probe
m25p80 spi-nor devices. Hence, add "spi-flash" compatible string to
m25p80 node. Without this patch, flash device DT data is not parsed and
QSPI operates in unsupported mode leading to data corruption.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add missing L3 cache flush functionality which absence prevents
Linux kernel from normal boot in case the L3 cache is enabled
by ATF.
The L3 cache is named the "last level" cache in order to keep
the terminology similar to the ATF code.
This cache should not be disabled by u-boot since the Linux
kernel cannot activate it, so it is activates at ATF stage.
However the cache flush is required for preventing data corruption
after disabling the MMU and the data cache before passing control
to the loaded Linux image.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add pin control nodes to APN806, CP-master, CP-slave and
Armada-7040 and Armada-8040 boards DTS files
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add a DM port of Marvell pin control driver.
The A8K SoC family contains several silicone dies interconnected
in a single package. Every die is normally equipped with its own
pin controller unit.
There are 2 pin controllers in A70x0 SoC and 3 in A80x0 SoC.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Align the Armada-8040-db and Armada-7040-db SPI and I2C
DTS settings with latest DB settings:
- 8040-db: disable i2c0 and spi0 on AP (MPPs are reserved for SDIO)
- 8040-db: disable cps_i2c0 on CP1
- 8040-db: enable spi1 on CP1 (the new location of the boot flash)
The spi1 on CP1 is aliased as spi0 since this is the way
the driver enumerates it.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This is a user configurable option, but "select BLK" forces users to
enable it.
Even with this commit, BLK is still enabled by "default y if DM_MMC"
for UniPhier SoCs; the difference is users can disable it if they
do not need it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Initialize EMIF OCP_CONFIG registers REG_COS_COUNT_1, REG_COS_COUNT_2,
and REG_PR_OLD_COUNT field for Beaglebone-Black and am335x-evm. With
the default values LCDC suffers from DMA FIFO underflows and frame
synchronization lost errors. The initialization values are the highest
that work flawlessly when heavy memory load is generated by CPU. 32bpp
colors were used in the test. On BBB the video mode used 110MHz pixel
clock. The mode supported by the panel of am335x-evm uses 30MHz pixel
clock.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
It is useful to name each method so that we can print out this name when
using the method. Currently this happens using a separate function. In
preparation for unifying this, add a name to each method.
The name is only available if we have libcommon support (i.e can use
printf()).
Signed-off-by: Simon Glass <sjg@chromium.org>
solve issue when bootstage is used with armV7 generic timer
first call of timer_get_boot_us() use the function get_timer()
before timer initialization (arch.timer_rate_hz = 0)
=> div by 0
Commit-notes
When I activate bootstage on ARMV7 architecture with platform
using the generic armv7 timer defined in file
./arch/arm/cpu/armv7m/timer.c
I have a issue because gd->arch.timer_rate_hz = 0
For me the get_timer() function should not used before timer_init
(which initialize gd->arch.timer_rate_hz) at least for the ARMV7
timer.
But in the init sequence, the first bootstage fucntion is called
before timer_init and this function use the timer function.
For me it is a error in the generic init sequence :
mark_bootstage is called before timer_init.
static init_fnc_t init_sequence_f[] = {
....
arch_cpu_init_dm,
mark_bootstage, /* need timer, go after init dm */
...
#if defined(CONFIG_ARM) || defined(CONFIG_MIPS) || \
defined(CONFIG_BLACKFIN) || defined(CONFIG_NDS32) || \
defined(CONFIG_SPARC)
timer_init, /* initialize timer */
#endif
.......
To solve the issue for all the paltform, we can move timer_init()
call just before mark_bootstage() in this array...
It should be ok for ARMV7 but I don't sure for other platform
impacted
- the other ARM platform or ARMV7 wich don't use generic timer
- MIPS BLACKFIN NDS32 or SPARC
and I don't sure of impact for other function called
(board_early_init_f for example....)
=> This patch solve issue only in timer armv7
get_boot_us() can be called everytime without div by 0 issue
(gd->arch.timer_rate_hz is not used)
END
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
Some Altera Quartus generated files have long lines that are split with a '\' at
the end of the line. It also wOn Windows, rites files in DOS format, which can
confuse some of the processing scripts in this file. This patch solves both issues.
Signed-off-by: Bill Randle <bill.randle@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Valid Altera SoCFPGA preloader image must contain special data at
offsets 0x40, 0x44, 0x48 and valid instructions at address 0x4c or
0x50. These addresses are by default used by U-Boot's vector table
and a piece of reset handler, thus a valid preloader corrupts those
addresses slightly. While this works most of the time, this can and
does prevent the board from rebooting sometimes and triggering this
issue may even depend on compiler.
The problem is that when SoCFPGA performs warm reset, it checks the
addresses 0x40..0x4b in SRAM for a valid preloader signature and
header checksum. If those are found, it jumps to address 0x4c or
0x50 (this is unclear). These addresses are populated by the first
few instructions of arch/arm/cpu/armv7/start.S:
ffff0040 <data_abort>:
ffff0040: ebfffffe bl ffff0040 <data_abort>
ffff0044 <reset>:
ffff0044: ea000012 b ffff0094 <save_boot_params>
ffff0048 <save_boot_params_ret>:
ffff0048: e10f0000 mrs r0, CPSR
ffff004c: e200101f and r1, r0, #31
ffff0050: e331001a teq r1, #26
Without this patch, the CPU will enter the code at 0xffff004c or
0xffff0050 , at which point the value of r0 and r1 registers is
undefined. Moreover, jumping directly to the preloader entry point
at address 0xffff0000 will also fail, because address 0xffff004.
is invalid and contains the preloader magic.
Add BOOT0 hook which reserves the area at offset 0x40..0x5f and
populates offset 0x50 with jump to the entry point. This way, the
preloader signature is stored in reserved space and can not corrupt
the SPL code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Stefan Roese <sr@denx.de>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Add CycloneV based Terasic DE1-SoC board. The board boots
from SD/MMC. Ethernet and USB host is supported.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Marek Vasut <marex@denx.de>
The default configuration for QSPI AHB bus can't support 16MB+.
But some flash on NXP layerscape board are more than 16MB.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add the name for register space and memory space.
<0x1550000 0x10000 > is the QSPI register space.
<0x40000000 0x4000000> is the QSPI memory space.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
- add additional function erratum_a009942_check_cpo to check if the
board needs tuning CPO calibration for optimal setting.
- move ERRATUM_A009942(with revision to check cpo_sample option) from
fsl_ddr_gen4.c to ctrl_regs.c for reuse on all DDR4/DDR3 parts.
- move ERRATUM_A008378 from fsl_ddr_gen4.c to ctrl_regs.c
- remove obsolete ERRATUM_A004934 which is replaced with ERRATUM_A009942.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
[YS: Replaced CONFIG_QEMU_E500 with CONFIG_ARCH_QEMU_E500]
Reviewed-by: York Sun <york.sun@nxp.com>
Not all memory is mapped in the MMU. So we need to restrict the memory
size so that U-Boot does not try to access it. Also, the internal
registers are located at 0xf000.0000 - 0xffff.ffff. Currently only 2GiB
are mapped for system memory. This is what we pass to the U-Boot
subsystem here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
To use the PCIe driver, its controller memory and the PCIe regions need
to get mapped in the MMU. Otherwise these areas can't be accessed.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
The Armada8k implements 2 CPs (communication processors) and the 2nd
CP also is equipped with a COMPHY controller. This patch now loops
over all enabled MISC devices (CP110) enabled in the DT to initialize
all CPs.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Add I2C and SPI aliases to enable usage in U-Boot. Otherwise U-Boot will
not be able to use the SPI NOR chip for environment storage and use
"i2c dev 0" to select this I2C bus.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
This patch adds the COMPHY device tree configuration to the DT file for
the Marvell DB-88F8040 devel board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
This patch adds the COMPHY and UTMI device tree nodes to the cp110-slave
dtsi file for the Armada 8K.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Since the cp110 slave also has comphy DT nodes, the names need to be
renamed to avoid a name clash. Lets use the common naming scheme:
"cpm_xxx" for master and "cps_xxx" for slave.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
This patch adds the necessary files to support the Marvell Armada 8k
devel board. Most board specfic files are shared with the Armada 7k
boards under the name "armada-8k*". So only minimal changes are
necessary to add this basic board support (except the DT files of
course).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
To enable access to the slave CP its memory needs to be added to the
MMU memory map.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Add the latest version of the DT files from the Linux kernel.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
This moves some of the Armada DB-88F7040 board specific files to a more
generic name: armada-8k. This is in preparation for the Armada-8k
support which will be added soon. And since both platforms share
most devices, lets also share most source files to not duplicate
the code here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
These are the last two samsung boards that don't use DM_I2C. Move them
over, leaving #ifdefs to allow the maintainer to complete this work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Three boards are still not converting to use DM_I2C. They are also using
the old PMIC framework. Rather than removing them, add #ifdefs to allow
them to continue to build. This will give the maintainers a little more
time to decide whether to convert them or not.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Commit 54e4fcfa3c ("ARM: mx6: add MMC2 boot device detection
support in SPL") prevents UDOO neo board to boot:
Trying to boot from MMC2
port 1
MMC Device 1 not found
spl: could not find mmc device. error: -19
SPL: failed to boot from all boot devices
This reverts commit 54e4fcfa3c.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
This board has not been converted to DM_SERIAL by the deadline.
Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: David Müller <d.mueller@elsoft.ch>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This board has not been converted to DM_SERIAL by the deadline.
Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: David Müller <d.mueller@elsoft.ch>
Update the board pinmux for AM572x-IDK board using latest PMT[1] and the
board files named am572x_gp_evm_A3a_sr2p0 that were autogenerated on
19th October, 2016 by "Ahmad Rashed<a-rashed@ti.com>".
[1] https://dev.ti.com/pinmux/app.html#/default/
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add DT support for dra71-evm and built it as part of FIT image.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Palmas driver assumes it is always TPS659xx regulator on all DRA7xx based
boards to enable mmc regulator. This is not true always like in case of
DRA71x-evm. So get this information based on the board.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Delete omap4_vmmc_pbias_config from omap_hsmmc.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add the pmic_data for LP873x PMIC which is used to power
up dra71x-evm.
Note: As per the DM[1] DRA71x supports only OP_NOM. So, updating
the efuse registers only to use OPP_NOM irrespective of any
CONFIG_DRA7_<VOLT>_OPP_{NOM,od,high} is defined.
[1] http://www.ti.com/product/DRA718/technicaldocuments
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch adds support to update the device-tree blob to adjust the
DSP and IVA DPLL clocks pertinent to the selected OPP choice, with
the default being OPP_NOM. The voltage settings are done in u-boot,
but the actual clock configuration itself is done in kernel because
of the following reasons:
1. SoC definition constraints us to NOT to do dynamic voltage
scaling ever after the initial avs0 setting in bootloader
- so the voltage must be set in bootloader.
2. The voltage level must be set even if the IP blocks like
GPU/DSP are unused.
3. The IVA, GPU and DSP DPLLs are not essential for u-boot functionality,
and similar DPLL clock configuration code has been cleaned up in
v2014.10 u-boot release. See commit, 02c41535b6 ("ARM: OMAP4/5:
Remove dead code against CONFIG_SYS_CLOCKS_ENABLE_ALL").
The non-essential DPLLs are configured within the kernel during
the clock init step when parsing the device tree and creating
the clock devices. This approach meets both the u-boot and kernel
needs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Subhajit Paul <subhajit_paul@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Redefine the macros used to define the voltage values and the
efuse register offsets based on OPP for all the voltage domains.
This is done using Kconfig macros that can be set in a defconfig
or selected during a config step. This allows a voltage domain
to be configured/set to a corresponding voltage value depending
on the OPP selection choice.
The Kconfig choices have been added for MPU, DSPEVE, IVA and GPU
voltage domains, with the MPU domain restricted to OPP_NOM. The
OPP_OD and OPP_HIGH options will be added when the support for
configuring the MPU clock frequency is added. The clock
configuration for other voltage domains is out of scope in
u-boot code.
The CORE voltage domain does not have separate voltage values
and efuse register offset at different OPPs, while the MPU
voltage domain only has different efuse register offsets for
different OPPs, but uses the same voltage value. Any different
choices of OPPs for voltage domains on common ganged-rails
is automatically taken care to select the corresponding
highest OPP voltage value.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
It can be expected that different paper spins of a SoC can have
different definitions for OPP and can have their own constraints
on the boot up OPP for each voltage rail. In order to have this
flexibility, add support for dynamically selecting the OPP voltage
based on the board to handle any such exceptions.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add an OPTEE node to the FDT when TEE installation has completed
successfully. This informs the kernel of the presence of OPTEE.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
secure_tee_install is used to install and initialize a secure TEE OS such as
Linaro OP-TEE into the secure world. This function takes in the address
where the signed TEE image is loaded as an argument. The signed TEE image
consists of a header (struct tee_header), TEE code+data followed by the
signature generated using image signing tool from TI security development
package (SECDEV). Refer to README.ti-secure for more information.
This function uses 2 new secure APIs.
1. PPA_SERV_HAL_TEE_LOAD_MASTER - Must be called on CPU Core 0. Protected
memory for TEE must be reserved before calling this function. This API
needs arguments filled into struct ppa_tee_load_info. The TEE image is
authenticated and if there are no errors, the control passes to the TEE
entry point.
2. PPA_SERV_HAL_TEE_LOAD_SLAVE - Called on other CPU cores only after
a TEE_LOAD_MASTER call. Takes no arguments. Checks if TEE was
successfully loaded (on core 0) and transfers control to the same TEE
entry point.
The code at TEE entry point is expected perform OS initialization steps
and return back to non-secure world (U-Boot).
Signed-off-by: Harinarayan Bhatta <harinarayan@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On DRA7xx platform, CPU Core 1 is not used in u-boot. However, in some
cases it is need to make secure API calls from Core 1. This patch adds
an assembly function to make a secure (SMC) call from CPU Core #1.
Signed-off-by: Harinarayan Bhatta <harinarayan@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The SPL is unable to load u-boot because the DDR2 is not configured.
Configure the DDR2.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The SPL is not able to boot properly because the PLL0 is not
configured. Configure it.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Clean config headers by moving CONFIG_SYS_DA850_DDR_INIT away to a
Kconfig file.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Clean config headers by moving CONFIG_SYS_DA850_PLL_INIT away to a
Kconfig file.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
CONFIG_AM57XX is just an unnecessary macro that is redundant given So,
remove the same instead of spreading through out the u-boot source
code and getting in the way to maintain common code for DRA7x family.
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
For ECC enabled DDR, we use EDMA to reset all memory values to 0. For
K2E/L/H/K the priv ID of 8 was indicative of ARM, but that is not the
case for K2G, where it is 1.
Unfortunately, ddr3 code had hard coded the privID and had missed
identification previously. Fix the same, else unforeseen behavior can
be expected in our reset of DDR contents to 0 for ECC enablement.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently all backend driver ops uses hard coded physical
address, so to adopt the driver to DM, add device pointer to ops
call backs so that drivers can get physical addresses from the
usb driver priv/plat data.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
MUSB wrapper driver is bound as MISC device and underlying usb
devices are bind to usb drivers based on dr_mode, so probing the
MISC wrapper driver to register musb devices.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Do not register usb devices when CONFIG_DM_USB is define.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Commit e2f88dfd2d ("libfdt: Introduce new ARCH_FIXUP_FDT option")
allows us to skip memory setup of DTB, but a problem for ARM is that
spin_table_update_dt() and psci_update_dt() are skipped as well if
CONFIG_ARCH_FIXUP_FDT is disabled.
This commit allows us to skip only fdt_fixup_memory_banks() instead
of the whole of arch_fixup_fdt(). It will be useful when we want to
use a memory node from a kernel DTB as is, but need some fixups for
Spin-Table/PSCI.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fixed build error for x86:
Signed-off-by: Simon Glass <sjg@chromium.org>
Now all mpc85xx and mpc86xx have converted to use SYS_CCSRBAR_DEFAULT
in Kconfig. Drop this macro for LSCH2 and remove from white list.
Signed-off-by: York Sun <york.sun@nxp.com>
Using alternative bootmode field to support automatic secondary boot
modes. It is purely software setting where SW modes are using free
bootmode combinations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP provides an option to overwrite bootmode setting which
can change SPL behavior.
For example: boot SPL via JTAG and then SPL loads images from SD.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The main PLL frequency is 2GHz for Armada-XP and 1GHZ for Armada 375,
38x and 39x.
[ Linux commit ae142bd9976532aa5232ab0b00e621690d8bfe6a ]
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch extends the imx6 clock code to enable or disable the EIM
slow clock, which in necessary when one wants to use EIM interface t
o read/write from external memory (e.g. NOR).
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
This patch adds initial support for Samtec VIN|ING 2000 board.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
UDOO Neo Board is a development board from Seco that has three models:
- UDOO Neo Basic
- UDOO Neo Basic Kick Starter
- UDOO Neo Extended
- UDOO Neo Full
All versions are based on the i.MX6 SoloX processor.
For more details about the UDOO Neo board, please refer to:
http://www.udoo.org/udoo-neo/
This work is based on a previous commit of Francesco Montefoschi
<francesco.monte@gmail.com>:
877b71184a
Only tested on the UDOO Neo Full board.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The DDR calibration routines are gated by conditionals for the
i.MX6DQ SOCs, but with the use of the sysinfo parameter, these
are usable on at least i.MX6SDL and i.MX6SL variants with DDR3.
Also, since only the Novena board currently uses the dynamic
DDR calibration routines, these routines waste space on other
boards using SPL.
Add a KConfig entry to allow boards to selectively include the
DDR calibration routines.
Signed-off-by: Eric Nelson <eric@nelint.com>
Add routine mmdc_read_calibration() to return the output of DDR
calibration. This can be used for debugging or to aid in construction
of static memory configuration.
This routine will be used in a subsequent patch set adding a virtual
"mx6memcal" board, but could also be useful when gathering statistics
during an initial production run.
Signed-off-by: Eric Nelson <eric@nelint.com>
The DDR calibration routines have scattered support for bus
widths other than 64-bits:
-- The mmdc_do_write_level_calibration() routine assumes the
presence of PHY1, and
-- The mmdc_do_dqs_calibration() routine tries to determine
whether one or two DDR PHYs are active by reading MDCTL.
Since a caller of these routines must have a valid struct mx6_ddr_sysinfo
for use in calling mx6_dram_cfg(), and the bus width is available in the
"dsize" field, use this structure to inform the calibration routines which
PHYs are active.
This allows the use of the DDR calibration routines on CPU variants
like i.MX6SL that only have a single MMDC port.
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The DDR calibration code is only setting flag DG_CMP_CYC (DQS gating sample
cycle) for the first PHY.
Set the 32-cycle flag for both PHYs and clear when done so the MPDGCTRL0
output value isn't polluted with calibration artifacts.
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add constants for the MPZQLP2CTL DDR register for both
banks to allow setting the LPDDR2 timing values in
.cfg files using a named constant instead of hex addresses
as is currently done in mx6slevk and other board files.
Signed-off-by: Eric Nelson <eric@nelint.com>
The ipu has two display interfaces. Make the used one a parameter
in struct display_info_t instead of using unconditionally DI0.
DI0 is the default setting.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Check BOOT_CFG2[3:4] to determine which SD/MMC port is selected to boot
from. If MMC2 is selected return BOOT_DEVICE_MMC2. In all other cases
return BOOT_DEVICE_MMC1, as we do not have corresponding macro for MMC3
and MMC4.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Before disable cache, need to first flush cache.
There maybe dirty data in D-Cache before disable D-Cache.
After disable D-Cache, the first store instructions in
psci_v7_flush_dcache_all will directly store registers
{r4-r5, r7, r9-r11, lr} to memory.
If there is dirty data before disable D-Cache,
psci_v7_flush_dcache_all will flush data to memory,
and may overwrite the memory that hold the registers
{r4-r5, r7, r9-r11, lr}.
So before disable cache, first flush D-Cache.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Hongbo Zhang <hongbo.zhang@nxp.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Tom Rini <trini@konsulko.com>
The rpi has a pretty simple way of resetting the whole system. All it takes
is to poke a few registers at a well defined location in MMIO space.
This patch adds support for the EFI loader implementation to allow an OS to
reset and power off the system when we're outside of boot time.
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch removes use of U_BOOT_DEVICE in board/raspberrypi/rpi/rpi.c,
enables OF_CONTROL in the config and adjusts the rpi_*defconfig configs.
Signed-off-by: Fabian Vogt <fvogt@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The information currently set via platdata has to be represented in the
device tree now. bcm283x-uboot.dtsi adds the u-boot specific "skip-init"
property to the serial nodes and enables initialization in the pre-reloc phase.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Fabian Vogt <fvogt@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds device trees for the bcm283x platform to be used with
OF_CONTROL. The version 4.8-rc7 of the linux kernel was used as source.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Fabian Vogt <fvogt@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The config option TARGET_K2x_EVM is set by the k2x defconfigs to pick
a board target, but the header configs also set K2x_EVM. This config
is redundant, remove it and use TARGET_K2x_EVM everywhere in its place.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Add board support for sun8i_r16 Nintendo NES Classic edition.
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
[jagan: Add commit message body]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Currently, USB is forced-enabled for the sunxi familly, and there is no
way to disable it.
However, USB takes a long time to initiliase, delaying the boot by up to
5 seconds (without any USB device attached!). This is a very long delay,
especially in cases where USB booting is not wanted at all, and where
the device is expected to boot relatively often (even in production).
Change the way the dependencies are handled, by only forcibly selecting
USB when CONFIG_DISTRO_DEFAULTS ("defaults suitable for booting general
purpose Linux distributions") is set. This option defaults to y for the
sunxi familly, so the current default behaviour is kept unchanged. Users
interested in boot time and/or size will be able to disable this to
further disable USB.
With USB disabled, the time spent in U-Boot before handing control to
the Linux kernel is about 1s now, down from ~5s (Nanopi Neo, sunxi H3).
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans De Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Today we can compile a self-contained hello world efi test binary that
allows us to quickly verify whether the EFI loader framwork works.
We can use that binary outside of the self-contained test case though,
by providing it to a to-be-tested system via tftp.
This patch separates compilation of the helloworld.efi file from
including it in the u-boot binary for "bootefi hello". It also modifies
the efi_loader test case to enable travis to pick up the compiled file.
Because we're now no longer bloating the resulting u-boot binary, we
can enable compilation always, giving us good travis test coverage.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This adds support for the Asus Chromebook Flip, an RK3288-based clamshell
device which can flip into 'tablet' mode. The device tree file comes from
Linux v4.8. The SDRAM parameters are for 4GB Samsung LPDDR3.
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds support for the Asus Chromebit, and RK3288-based device designed
to plug directly into an HDMI monitor. The device tree file comes from
Linux v4.8.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update board_init() to increase the ARM clock to the maximum speed on
veyron boards. This makes quite a large difference in performance. With
this change, speed goes from about 750 DMIPS to 2720 DMIPs.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we have a single rk3288-based Chromebook: chromebook_jerry. But
all such Chromebooks can use the same binary with only device-tree
differences. The family name is 'veyron', so rename the files accordingly.
Also update the device-tree filename since this currently differs from
Linux.
Signed-off-by: Simon Glass <sjg@chromium.org>
Check whether a display device is in use before using it. Add a comment as
to why two displays cannot currently be used at the same time.
This allows us to remove the device-tree change that disables vopb on
jerry.
Signed-off-by: Simon Glass <sjg@chromium.org>
This board always boots from SPI, so update the code to support that with
of-platdata. The boot source is not currently available with of-platdata.
Signed-off-by: Simon Glass <sjg@chromium.org>
As PSCI and secure monitor firmware framework are enabled, this patch is
to support loading 32-bit OS in such case. The default target exception
level returned to U-Boot is EL2, so the corresponding work to switch to
AArch32 EL2 and jump to 32-bit OS are done in U-Boot and secure firmware
together.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Spin-table method is used for secondary cores to load 32-bit OS. The
architecture information will be got through checking FIT image and
saved in the os_arch element of spin-table, then the secondary cores
will check os_arch and jump to 32-bit OS or 64-bit OS automatically.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
To support loading a 32-bit OS, the execution state will change from
AArch64 to AArch32 when jumping to kernel.
The architecture information will be got through checking FIT image,
then U-Boot will load 32-bit OS or 64-bit OS automatically.
Signed-off-by: Ebony Zhu <ebony.zhu@nxp.com>
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove the custom low-level initialization function and reuse the
default low-level initialization function. But this requires the
ARMV8_MULTIENTRY config option to be enabled for Exynos7420.
On Exynos7420, the boot CPU belongs to the second cluster and so
with ARMV8_MULTIENTRY config option enabled, the 'branch_if_master'
macro fails to detect the CPU as boot CPU. As a temporary workaround
the CPU_RELEASE_ADDR is set to point to '_main'.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
NXP ARMv8 SoC LS2080A release all secondary cores in one-go.
But other new SoCs like LS2088A, LS1088A release secondary
cores one by one.
Update code to release secondary cores based on SoC SVR
Add code to release cores one by one for non LS2080A SoCs
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[YS: remove "inline" from declaration of initiator_type]
Reviewed-by: York Sun <york.sun@nxp.com>
The QorIQ LS2088A SoC is built on layerscape architecture.
It is similar to LS2080A SoC with some differences like
1)Timer controller offset is different
2)It has A72 cores
3)It supports TZASC module
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2080 SoC and its personalities does not support TZASC
But other new SoCs like LS2088A, LS1088A supports TZASC
Hence, skip initializing TZASC for Ls2080A based on SVR
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TZASC registers like TZASC_GATE_KEEPER, TZASC_REGION_ATTRIBUTES
are 32-bit regsiters.
So while doing register load-store operations, 32-bit intermediate
register, w0 should be used.
Update x0 register to w0 register type.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Timer controller base address has been changed from
LS2080A SoC (and its personalities) to new SoCs like
LS2088A, LS1088A.
Use SVR based timer base address detection to avoid compile time #ifdef.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Implement a hook to allow boards to save boot-time CPU state for later
use. When U-Boot is chain-loaded by another bootloader, CPU registers may
contain useful information such as system configuration information. This
feature mirrors the equivalent ARMv7 feature.
Signed-off-by: Cédric Schieli <cschieli@gmail.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
With the move to arch/arm/mach-omap2 there are now very few uses of
CONFIG_OMAP_COMMON and further they can all be replaced with
CONFIG_ARCH_OMAP2, so do so.
Signed-off-by: Tom Rini <trini@konsulko.com>
This moves what was in arch/arm/cpu/armv7/omap-common in to
arch/arm/mach-omap2 and moves
arch/arm/cpu/armv7/{am33xx,omap3,omap4,omap5} in to arch/arm/mach-omap2
as subdirectories. All refernces to the former locations are updated to
the current locations. For the logic to decide what our outputs are,
consolidate the tests into a single config.mk rather than including 4.
Signed-off-by: Tom Rini <trini@konsulko.com>
To start consolidating various TI-related code, introduce the ARCH_OMAP2
symbol. While we have removed omap2-specific boards some time ago,
matching up with the kernel naming here will help overall.
Signed-off-by: Tom Rini <trini@konsulko.com>
Detect the board very early and avoid reading eeprom multiple times.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is similar to Commit 93e6253d11 ("ARM: OMAP4/5: Centralize
early clock initialization") that was done for OMAP4+, reflecting the same
for AM33xx and AM43xx SoCs to centralize clock initialization.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add setup_early_clocks that calls setup_clocks_for_console for
ti81xx]
Signed-off-by: Tom Rini <trini@konsulko.com>
Update CONFIG_LS2080A to CONFIG_FSL_LSCH3 to make those workaround
implementing of erratum reusable for more SoCs.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The patch adds support for Freescale ls1021a-iot board.
Signed-off-by: Feng Li <feng.li_2@nxp.com>
[YS: rewrite commit message, fix whitespace in Kconfig]
Reviewed-by: York Sun <york.sun@nxp.com>
Early system initialization is being done before initf_dm is being called
in U-Boot. Then system will fail to boot if any of the DM enabled driver
is being called in this system initialization code. So, rearrange the
code a bit so that DM enabled drivers can be called during early system
initialization. This is inspired by commit e850ed82bc ("ARM: OMAP4+: Allow
arch specific code to use early DM")
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Set the appropriate bits in the interface config register based
on the SPI_ mode flags.
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Highlights this time around:
- x86 efi_loader support
- hello world efi test case
- network device name is now representative
- terminal output reports modes correctly
- fix psci reset for ls1043/ls1046
- fix efi_add_runtime_mmio definition for x86
- efi_loader support for ls2080
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=xmR3
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2016-11-17
Highlights this time around:
- x86 efi_loader support
- hello world efi test case
- network device name is now representative
- terminal output reports modes correctly
- fix psci reset for ls1043/ls1046
- fix efi_add_runtime_mmio definition for x86
- efi_loader support for ls2080
When implementing efi loader support, we can expose runtime services
for payloads. One such service is CPU reset.
This patch implements RTS CPU reset support for layerscape systems.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
The efi loader code has its own memory map, so it needs to be aware where
the spin tables are located, to ensure that no code writes into those
regions.
Signed-off-by: Alexander Graf <agraf@suse.de>
On ls2080 we have a separate network fabric component which we need to
shut down before we enter Linux (or any other OS). Along with that also
comes configuration of the fabric using a description file.
Today we always stop and configure the fabric in the boot script and
(again) exit it on device tree generation. This works ok for the normal
booti case, but with bootefi the payload we're running may still want to
access the network.
So let's add a new fsl_mc command that defers configuration and stopping
the hardware to when we actually exit U-Boot, so that we can still use
the fabric from an EFI payload.
For existing boot scripts, nothing should change with this patch.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
[agraf: Fix x86 build]
The NXP ls1043 and ls1046 systems do not (yet) have PSCI enablement
for reset. Don't enable generic PSCI reset code on them.
Signed-off-by: Alexander Graf <agraf@suse.de>
According to design team, we need to set REFTOP_VBGADJ
in PMU MISC0 according to the REFTOP_TRIM[2:0] fuse. the
actually table is as below:
'000" - set REFTOP_VBGADJ[2:0] to 3'b000
'001" - set REFTOP_VBGADJ[2:0] to 3'b001
'010" - set REFTOP_VBGADJ[2:0] to 3'b010
'011" - set REFTOP_VBGADJ[2:0] to 3'b011
'100" - set REFTOP_VBGADJ[2:0] to 3'b100
'101" - set REFTOP_VBGADJ[2:0] to 3'b101
'110" - set REFTOP_VBGADJ[2:0] to 3'b110
'111" - set REFTOP_VBGADJ[2:0] to 3'b111
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Need to gate ENET clock when switching to a new clock parent, because
the mux is not glitchless.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye.Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Adding prefetchable memory space to pcie device tree node.
Shifting configuration space to 64-bit address space.
Removing pcie device tree node from amba as it requires size-cells=<2>
in order to access 64-bit address space.
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Zynqmp DMA driver expects two clocks (main clock and apb clock)
For LPDDMA channels the two clocks are missing in the
Dma node resulting probe failure.
xilinx-zynqmp-dma ffa80000.dma: main clock not found.
xilinx-zynqmp-dma ffa80000.dma: Probing channel failed
xilinx-zynqmp-dma: probe of ffa80000.dma failed with error -2
This patch fixes this issue.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
LPDDMA default allows only secured access.
inorder to enable these dma channels,
one should ensure that it allows non secure access.
This patch updates the same.
Reported-by: Sai Pavan Boddu <saipava@xilinx.com>
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use 64bit size cell for main amba bus instead of 32bit because PCIe
node requires it Change 64bit sizes also for all others IPs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This reverts commit bd750e7a6c
Implemented the new workaround for auto tuning based on
zynqmp compatible string, so removed the 'broken-tuning'
property.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch changes the compatible string for sdhci node,
adds "xlnx,device_id" and "xlnx,mio_bank" property to sdhci node.
Signed-off-by: Sai Krishna Potthuri <lakshmis@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds edac node for arm cortexa53 to report
errors on L1 and L2 caches.
Signed-off-by: Naga Sureshkumar Relli <nagasure@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This reverts commit 786db82bd5.
Since we are using serdes driver , no need of mapping serdes register
space into DP driver.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Tested-by: Hyun Kwon <hyunk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Each plane can be associated with multiple DMA channels. So add
index for each DMA channel.
Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Updating required device tree changes as per mainlined driver
from 4.6 kernel.
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Previously, it was assumed that there is a 1:1 mapping between
PM ID defined in the platform firmware and a PM domain. However, there
can be a situation where multiple PM IDs belong to a single PM domain
(e.g. PM IDs for GPU and two pixel processors correspond to a single
PM domain).
This patch adds support for assigning more than one PM ID to
a single PM domain.
Updated documentation accordingly.
Assigned pixel processors PM IDs to GPU PM domain.
Signed-off-by: Filip Drazic <filip.drazic@aggios.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DDR power states are handled by the PM firmware, so this domain is
redundant. Also, since there is no device using this PM domain,
it will be powered off during boot, which is wrong.
Signed-off-by: Filip Drazic <filip.drazic@aggios.com>
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add dcc to dtsi for supporting system without serial port.
DCC is enabled by default on ZynqMP.
Adding dcc to zcu100 and zcu102 which were tested.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Zynqmp DMA driver expects two clocks (main clock and apb clock)
LPDDMA clock cofiguration is missing for the same in the
zynqmp-clk.dtsi file.
This patch updates for the same.
Reported-by: Sai Pavan Boddu <saipava@xilinx.com>
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DTC 1.4.2 reports these warnings:
Warning (unit_address_vs_reg): Node /amba_apu has a reg or ranges
property, but no unit name
Warning (unit_address_vs_reg): Node /amba has a reg or ranges property,
but no unit name
Warning (unit_address_vs_reg): Node /amba/usb@fe200000 has a unit name,
but no reg property
Warning (unit_address_vs_reg): Node /amba/usb@fe300000 has a unit name,
but no reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-video0channel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-video1channel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-video2channel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-graphicschannel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-audio0channel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node
/amba/dma@fd4c0000/dma-audio1channel@fd4c0000 has a unit name, but no
reg property
Warning (unit_address_vs_reg): Node /memory has a reg or ranges
property, but no unit name
This patch is fixing them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DTC 1.4.2 reports these warnings:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges
property, but no unit name
Warning (unit_address_vs_reg): Node /pmu has a reg or ranges property,
but no unit name
Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name,
but no reg property
This patch is fixing them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Do not setup use_alt bit which copy alternative boot mode to
boot mode. The reason is that this bit is cleared after POR
but not after any software reset which will cause
that after SW reset bootrom will look for different boot image.
This patch setups alternative boot mode selection (purely SW
handling) and extends code to read this alternative boot mode first and
use it if it is setup.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for SD1 with level shifters bootmode.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support to check the buswidth on nand flash
at runtime based on nand MIO configurations done by FSBL.
User needs to correctly configure the MIO's based on the
buswidth supported by the nand flash which is present on the board.
Added nand8 and nand16 @periph names on slcr driver.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The topic-miami SoMs contain a Zynq xc7z015 or xc7z030 SoC, 1GB DDR3L RAM,
32MB QSPI NOR flash and 256MB NAND flash.
The topic-miamiplus SoMs contain a Zynq xc7z035, xc7z045 or xc7z100 SoC,
2x 1GB DDR3L RAM, 64MB dual-parallel QSPI flash, clock sources
and a fan controller.
The "Florida" carrier boards add SD, USB, ethernet and other interfaces.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add a string description for SYS_VENDOR to allow configuring boards from
other vendors than just "xilinx".
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Zynq/ZynqMP boot.bin file contains a region for register initialization
data. Filling in proper values in this table can reduce boot time
(e.g. about 50ms faster on QSPI boot) and also reduce the size of
the SPL binary.
The table is a simple text file with register+data on each line. Other
lines are simply skipped. The file can be passed to mkimage using the
"-R" parameter.
It is recommended to add reg init file to board folder.
For example:
CONFIG_BOOT_INIT_FILE="board/xilinx/zynqmp/xilinx_zynqmp_zcu102/reg.int
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for EFI apps on aarch64. This includes start-up and relocation
code plus a link script.
Signed-off-by: Simon Glass <sjg@chromium.org>
[agraf: add kconfig dep]
Signed-off-by: Alexander Graf <agraf@suse.de>
Add support for EFI apps on ARM. This includes start-up and relocation
code, plus a link script and some compiler setting changes.
Signed-off-by: Simon Glass <sjg@chromium.org>
[agraf: Remove whitespace change, add kconfig dep]
Signed-off-by: Alexander Graf <agraf@suse.de>
Rather than hard-coding the relocation type, add it to the ELF header file
and use it from there.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Update the spi-max-frequency property of m25p80 flash slave to match
that of TI QSPI controller node, so that QSPI operations happen at
maximum supported frequency of 76.8MHz.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Update the PLL initialization sequence to avoid glitches while
programming. User guide for the same is available at[1].
[1] http://www.ti.com/lit/ug/sprugv2h/sprugv2h.pdf
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
While we setup the mmu initially we mark set_section_dcache with
DCACHE_OFF flag. In case of non-LPAE mode the DCACHE_OFF macro
is rightly defined with TTB_SECT_XN_MASK set so as to mark all the
4GB XN. In case of LPAE mode XN(Execute-never) bit is not set with
DCACHE_OFF. Hence XN bit is not set by default for DCACHE_OFF which
keeps all the regions execute okay and this leads to random speculative
fetches in random memory regions which was eventually caught by kernel
omap-l3-noc driver.
Fix this to mark the regions as XN by default.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
An SMC call is required for all cache-wide operations on Tegra186. This
patch implements the two missing hooks now that U-Boot supports them, and
fixes the mapping of "hook name" to SMC call code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
SoC-specific logic may be required for all forms of cache-wide
operations; invalidate and flush of both dcache and icache (note that
only 3 of the 4 possible combinations make sense, since the icache never
contains dirty lines). This patch adds an optional hook for all
implemented cache-wide operations, and renames the one existing hook to
better represent exactly which operation it is implementing. A dummy
no-op implementation of each hook is provided.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
When performing a cache disable function, code must not access DRAM.
That is because when the cache is disabled, it will be bypassed and all
loads and stores will be serviced by RAM. This prevents accessing any
dirty data in the cache. In turn, this means the stack cannot be
used, since that is in RAM. To guarantee that code doesn't use RAM (and
in particular the stack) __asm_flush_l3_cache() must be manually
implemented in assembly, rather than implemented in C since the compiler
won't know not to touch RAM.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
nvtboot_boot_x0 is a 64-bit variable and hence must be 64-bit aligned.
So far this has happened by accident! Fix the code so this is guaranteed.
This fixes the following build error:
... relocation truncated to fit: R_AARCH64_LDST64_ABS_LO12_NC
against symbol `nvtboot_boot_x0' ...
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enable the Ethernet device in DT, provide board-specific configuration,
and enable the driver in Kconfig.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tegra186 includes a Synopsys DWC EQoS (Ethernet) device. Add this to the
Tegra186 SoC DT so that boards can make use of it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
On Tegra186, the bootloader which runs before U-Boot passes the Ethernet
MAC address to U-Boot using device tree. Extract this value and write it
to the environment, so that the Ethernet uclass picks it up and uses it
for the built-in Ethernet device.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Extend the Tegra186 implementation of board_late_init() to call a per-SoC
"hook" function. This will allow SoC-specific (rather than Tegra-wide)
functionality to be implemented without the core Tegra code needing to be
aware of the details. While board186.c is currently only used for
Tegra186, it should be applicable to any other future SoC, and perhaps its
simple design could be back-ported to older SoCs in the future too.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
For 64-bit ARM systems we provide just a timer_read_counter()
implementation and rely on the generic non-uclass get_ticks() function
in lib/time.c to call the former.
However this function is actually not 64-bit safe, as it assumes a
"long" to be 32-bit. Beside the fact that the resulting uint64_t
isn't bigger than "long" on 64-bit architectures and thus combining two
counters makes no sense, we get all kind of weird results when we try
to OR in the high value shifted by _32_ bits.
So let's avoid that function at all and provide a straight forward
get_ticks() implementation for ARMv8, which also is in line with ARMv7.
This fixes occasional immediate time-out expiration issues I see on the
Pine64 board. The root cause of this needs to be investigated, but this
fix looks like the right thing anyway.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Cover-Letter: Fixes several spelling errors for the words "resetting",
"extended", "occur", and "multiple".
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
SPL_MMC_SUPPORT defined in rockchip top level Kconfig instead of
inside rk3288 and default to disable if ROCKCHIP_SPL_BACK_TO_BROM
defined.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since we implement the dram capacity auto detect, we don't
need to set the channel number and sdram-channel in dts.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Add support for rk3288 dram capacity auto detect, support DDR3 and
LPDDR3, DDR2 is not supported.
The program will automatically detect:
- channel number
- rank number
- column address number
- row address number
The dts file do not need to describe those info after apply this patch.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Simon Glass <sjg@chromium.org>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
The Clock Multiplier in rk3399 EMMC programmable clock generator
is broken, we can remove its support from SoC GRF register.
Without this patch, rk3399 emmc driver is not work after below patch
applied:
6dffdbc mmc: sdhci: Add the programmable clock mode support
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
This function is called from outside the driver. It should be placed into
common SoC code. Move it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This function is called from outside the driver. It should be placed into
common SoC code. Move it.
Also rename the driver symbol to be more consistent with the other rockchip
clock drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This function is called from outside the driver. It should be placed into
common SoC code. Move it.
Also rename the driver symbol to be more consistent with the other rockchip
clock drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Mostly by adding MACH_SUN50I to some existing #ifdefs enable support
for the the HCI0 USB host controller on the A64.
Fix up some minor 64-bit hiccups on the way.
Add the bare minimum DT bits to the A64 .dtsi and enable the controllers
and the PHY on the Pine64.
This is limited to the first USB controller at the moment, which is
connected to the lower USB socket on the Pine64 board.
[Andre: remove unneeded defines, enable OHCI, add commit message]
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The A80 has SID e-fuses. Like other newer SoCs, the actual e-fuses
are at an offset of 0x200 within the SID address space.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The sun8i-emac driver works fine with the A64 Ethernet IP, but we are
missing an alias entry to trigger the driver instantiation by U-Boot.
Add the line to point U-Boot to the Ethernet DT node.
This enables TFTP boot on the Pine64.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
CONFIG_SUNXI -> CONFIG_ARCH_SUNXI
and removed CONFIG_SUNIX from config_whitelist.txt
Cc: Simon Glass <sjg@chromium.org>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This is a cleaned up version set_pll() from Allwinner's boot0 source
(bootloader/basic_loader/bsp/bsp_for_a80/common/common.c).
[wens@csie.org: Added commit message; style cleanup]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Since the A80 has many cores which we intend to use in SMP fashion,
we should set the SMP bit for the boot CPU.
[wens@csie.org: Added commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
On sun9i, the GTBUS manages transaction priority and bandwidth
for multiple read ports when accessing DRAM. The initialisation
mirrors the settings from Allwinner's boot0 for now, even though
this may not be optimal for all applications (e.g. headless
systems might want to give priority to IO modules).
Adding a common callout to gtbus_init() from the SPL clock init
with a weakly defined implementation in sunxi/clock.c to fallback
to for platforms that don't require this.
[wens@csie.org: Moved gtbus_sun9i.c to arch/arm/mach-sunxi/; style cleanup]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This adds DRAM initialisation code for sun9i, which calculates the
appropriate timings based on timing information for the supplied
DDR3 bin and the clock speeds used.
With this DRAM setup, we have verified DDR3 clocks of up to 792MHz
(i.e. DDR3-1600) on the A80-Q7 using a dual-channel configuration.
[wens@csie.org: Moved dram_sun9i.c to arch/arm/mach-sunxi/; style cleanup]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[hdegoede@redhat.com: Drop some huge non-documenting #if 0 ... #endif blocks]
[hdegoede@redhat.com: Fix checkpatch warnings]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add the LD11 SoC data and adjuts the printf() format because this is
a 64-bit SoC. Otherwise, 16-digits pointer addresses would break
the log format.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Do not hard-code the number of DX blocks because it is a different
value for LD11 SoC.
Move the macro NR_DATX8_PER_DDRPHY to ddrphy-training.c since it
is the last user.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The DDR PHY register view of LD11 is slightly different from that
of LD4/Pro4/sLD8, but it will be possible to share the register
macros (and I want to re-use as much code as possible). Change
the code in the more flexible form.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The USB boot without the stand-by MPU is available on ES3 or later
of LD11 SoC, but the code in this if-conditional block must not be
run when booting from USB. Check if the boot device is USB, and
skip the code in the case.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
