Buck regulator 1, 2 and 3 of TPS6594132 on j721e-sk is in 3 Phase
confguration, in-order to support this, add configuring 3 Phase buck
in tps65941 while driver probing.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Since TPS659412 and TPS659413 are both software compatible,
add a compatible string for the same inside tps65941.c.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
There are devices which cause a USB stall when trying to read strings.
Specifically Arduino Mega R3 stalls when trying to read the product
string.
The stall currently remains unhandled, and subsequent retries submit new
transfers on a stopped endpoint which ultimately cause a crash in
abort_td():
WARN halted endpoint, queueing URB anyway.
XHCI control transfer timed out, aborting...
Unexpected XHCI event TRB, skipping... (3affe040 00000000 13000000 02008401)
BUG at drivers/usb/host/xhci-ring.c:505/abort_td()!
BUG!
resetting ...
Linux seems to be able to recover from the stall by issuing a
TRB_RESET_EP command.
Introduce reset_ep() which issues a TRB_RESET_EP followed by setting the
transfer ring dequeue pointer via TRB_SET_DEQ. This allows to properly
recover from a USB stall error and continue communicating with the USB
device.
Signed-off-by: Stefan Agner <stefan@agner.ch>
The kernel devicetree has definitions for port and hub nodes as subnodes
to the USB devices. These subnodes don't contain all of the data required
to properly configure the dwc3. Check the parent nodes if the data is not
in the port/hub node.
Here's an example from the librem5 kernel dts file
&usb_dwc3_0 {
#address-cells = <1>;
#size-cells = <0>;
dr_mode = "otg";
snps,dis_u3_susphy_quirk;
status = "okay";
port@0 {
reg = <0>;
typec_hs: endpoint {
remote-endpoint = <&usb_con_hs>;
};
};
port@1 {
reg = <1>;
typec_ss: endpoint {
remote-endpoint = <&usb_con_ss>;
};
};
};
&usb_dwc3_1 {
dr_mode = "host";
status = "okay";
#address-cells = <1>;
#size-cells = <0>;
/* Microchip USB2642 */
hub@1 {
compatible = "usb424,2640";
reg = <1>;
#address-cells = <1>;
#size-cells = <0>;
mass-storage@1 {
compatible = "usb424,4041";
reg = <1>;
};
};
};
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Add phy and reset support for ceva sata IP. Phy and reset are optional
properties that's why detect if description is available. If not just
continue with operation.
This code was tested on Xilinx Kria SOM kv260-revA with sata connector
populated.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/eb3adf649be866aab19fc70ecc0fc8921545b1ac.1644226590.git.michal.simek@xilinx.com
Driver should be enabled by CONFIG_POWER_DOMAIN=y and
CONFIG_ZYNQMP_POWER_DOMAIN=y. Power domain driver doesn't have own DT node
but it uses zynqmp firmware DT node that's why there is a need to bind
driver when firmware node is found.
Driver itself is simple. It is sending pmufw config object overlay for
enabling access to device which is done in ...domain_request().
In ...domain_on() capabilities are passed and node is requested.
This should be bare minimum of required to get power domain driver working.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/f4b9433b91c0b18c375b061c7a4e29d428f70547.1644226055.git.michal.simek@xilinx.com
Some usb-nop-xceiv devices use a gpio take them out
of reset. Add a reset function to put them into that
state. This is similar to how Linux handles the
usb-nop-xceiv driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
When parsing the dfu_alt_info, check the number of arguments
and argument string strictly. If there is any garbage data
(which is not able to be parsed correctly) in dfu_alt_info,
that means something wrong and user may make a typo or mis-
understanding about the syntax. Since the dfu_alt_info is
used for updating the firmware, this mistake may lead to
brick the hardware.
Thus it should be checked strictly for making sure there
is no mistake.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
If dfu_alt_info has repeated spaces or tab (for indentation or
readability), the dfu fails to parse it. For example, if
dfu_alt_info="mtd nor1=image raw 100000 200000" (double spaces
after "raw"), the image entity start address is '0' and the size
'0x100000'. This is because the repeated space is not skipped.
Use space and tab as a separater and apply skip_spaces() to
skip redundant spaces and tabs.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Use strlcpy() instead of strcpy() to prevent copying the
entity name over the name buffer size.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
In the Linux implementation of adc-keys
(drivers/input/keyboard/adc-keys.c), `press-threshold-microvolt` is not
really interpreted as a threshold, but rather as the "nominal voltage"
of the button. When the voltage read from the ADC is closest to a
button's `press-threshold-microvolt`, the button is considered pressed.
This patch reconciles the behavior of button-adc with Linux's adc-keys
such that device trees can be synchronized with minimal modifications.
Signed-off-by: Peter Cai <peter@typeblog.net>
The ci_req->hw_buf can be NULL, test whether it is and if so,
avoid accessing it. Else, the system may crash.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Li Jun <jun.li@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
The imx8mm and imx8mn appear compatible with imx7d-usb
flags in the OTG driver. If the dr_mode is defined as
host or peripheral, the device appears to operate correctly,
however the auto host/peripheral detection results in an error.
The solution isn't just adding checks for imx8mm and imx8mn to
the check for imx7, because the USB clock needs to be running
to read from the USBNC_PHY_STATUS_OFFSET register or it will hang.
Marek requested that I not enable the clocks in ehci_usb_of_to_plat,
so I modified that function to return an unknown state if the
device tree does not explicitly state whether it is a host
or a peripheral.
When the driver probes, it looks to see if it's in the unknown
state, and only then will it read the register to auto-detect.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
This driver adds support for the keyboard on Apple Silicon laptops.
The controller for this keyboard sits on an SPI bus and uses an
Apple-specific HID over SPI protocol. The packets sent by this
controller for key presses and key releases are fairly simple and
are decoded directly by the code in this driver and converted into
standard Linux keycodes. The same controller handles the touchpad
found on these laptops. Packets for touchpad events are simply
ignored.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
Add a driver for the SPI controller integrated on Apple SoCs.
This is necessary to support the keyboard on Apple Silicon laopts
since their keyboard uses an Apple-specific HID over SPI protocol.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
Add a driver for the NVMe storage controller integrated on
Apple SoCs. This NVMe controller isn't PCI based and deviates
from the NVMe standard in its implementation of the command
submission queue and the integration of an NVMMU that needs
to be managed. This commit tweaks the core NVMe code to
support the linear command submission queue implemented by
this controller. But setting up the submission queue and
managing the NVMMU controller is handled by implementing
the driver ops that were added in an earlier commit.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Tested-on: firefly-rk3399
Tested-by: Mark Kettenis <kettenis@openbsd.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
The power management controller found on Apple SoCs als provides
a way to reset all devices within a power domain. This is needed
to cleanly shutdown the NVMe controller before we hand over
control to the OS.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add a function to disable the NVMe controller. This will be used
to let the driver for the NVMe storage integrated on Apple SoCs
shutdown the NVMe controller such we can shutdown the NVMe
IOP controller in a clean way afterwards before handing control
to the OS.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
The NVMe storage controller integrated on Apple SoCs deviates
from the NVMe standard in two aspects. It uses a "linear"
submission queue and it integrates an NVMMU that needs to be
programmed for each NVMe command. Introduce driver ops such
that we can set up the linear submission queue and program the
NVMMU in the driver for this strange beast.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
This mailbox driver provides a communication channel with the
Apple IOP controllers found on Apple SoCs. These IOP controllers
are used to implement various functions such as the System
Manegement Controller (SMC) and NVMe storage. It allows sending
and receiving a 96-bit message over a single channel.
The header file with the struct used for mailbox messages is taken
straight from Linux.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
Apple SoCs have an integrated NVMe controller that isn't connected
over a PCIe bus. In preparation for adding support for this NVMe
controller, split out the PCI support into its own file. This file
is selected through a new CONFIG_NVME_PCI Kconfig option, so do
a wholesale replacement of CONFIG_NVME with CONFIG_NVME_PCI.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
binman fit improvements
ACPI fixes and making MCFG available to ARM
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmIEGscRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZVkwf/RO9qLM/qtpcvtzFTciVFa/GQwd922abw
Anc4DYDBFTWfVymBTZT4Te0luTkZpqBV9cLEGw4XGYKGt+daVYB4cNKknKDOWqLI
adF7xHK2utT3OBlR7pL4d0Rvq0DAAFmyizkbi/CKHhrrpPkW8rPEiZlMwi+WQlTb
9Qv3deoVnRn3ivgw3AnTny+S52IFuI9pH4a34ASWfpOi3gGzICtIAnhVpRXdD+3A
TIhgK6XaGxBc0lVThsqc20FWfZ6rb4WyBRTRgbYivHn/fQxkynxBdSD6WU1ZdGH8
UZGjk5wBIkf+OyHjNQo/VEwoRHXR1k435+gsehUV8LvzytUykzP/FA==
=7Gel
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-8feb22-take3' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
patman snake-case conversion
binman fit improvements
ACPI fixes and making MCFG available to ARM
[trini: Update scripts/pylint.base]
Signed-off-by: Tom Rini <trini@konsulko.com>
Quite a few RISC-V emulators and ISS (including Spike) have host
transfer interface (HTIF) based console. This patch adds HTIF
based console driver for RISC-V platforms which depends totally
on DT node for HTIF register base address.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: Rick Chen <rick@andestech.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
if CONFIG_DM_STDIO is defined but SERIAL_PRESENT not,
gcc drops warnings for serial_stub_* functions
that they are defined but not used.
Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
nulldev_serial_input is static and not used in this file,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SCSI_AHCI_PLAT
CONFIG_SYS_SCSI_MAX_SCSI_ID
CONFIG_SYS_SCSI_MAX_LUN
CONFIG_SYS_SATA_MAX_DEVICE
Drop CONFIG_SCSI for everything except the sandbox build. We only need
one build for tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This is defined based on two other CONFIGs for all boards except sandbox
and durian.
For sandbox the value does not matter. For durian the value seems
excessive.
Drop the option completely, to simplify configuration and reduce the
number of things we need to convert to Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
At present all ahci drivers depend on AHCI except for DWC_AHCI. But no
boards enable that without also enabling AHCI:
/tools/moveconfig.py -f ~AHCI DWC_AHCI
0 matches
Group them together and sort them in order by Kconfig name (except for
AHCI_MVEBU which uses a different naming convention).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
No boards use this driver without CONFIG_BLK, so clean up the dead code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Move the SATA options inside an 'if SATA' part, so they are grouped.
Fix the 'Complient' typo while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
No boards currently use SATA without BLK:
./tools/moveconfig.py -f SATA ~BLK
0 matches
Make SATA depend on BLK to avoid any future confusion. Drop the dead code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This is not used in U-Boot and has not been converted to driver model.
Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_SYS_IDE_MAXBUS
CONFIG_SYS_IDE_MAXDEVICE
CONFIG_SYS_ATA_BASE_ADDR
CONFIG_SYS_ATA_STRIDE
CONFIG_SYS_ATA_DATA_OFFSET
CONFIG_SYS_ATA_REG_OFFSET
CONFIG_SYS_ATA_ALT_OFFSET
CONFIG_SYS_ATA_IDE0_OFFSET
CONFIG_SYS_ATA_IDE1_OFFSET
CONFIG_ATAPI
CONFIG_IDE_RESET
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
At present the IS_ENABLED() macro has extra brackets, making it possible
to write:
if IS_ENABLED(CONFIG_XXX)
but it is a bit confusing. Add the missing brackets.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Seems that we need the waterlevel setting not only for PIO mode as
without this at least the i.MX 8M Mini won't boot anymore when being
written by such a U-Boot. Corruption has also been observed both on
the i.MX 6 as well as i.MX 8M Mini when using ums on the eMMC. Fix
this by setting the watermark level again regardless of whether in
DMA or PIO mode.
Fixes: 41c6a22fc2 ("mmc: fsl_esdhc_imx: simplify esdhc_setup_data()")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
In some cases, a single SerDes instance can be shared between two different
processors, each using a separate link. In these cases, the SerDes
configuration is done in an earlier boot stage. Therefore, add support to
skip reconfiguring, if it is was already configured beforehand.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Add support for multilink configuration of Sierra PHY. Currently,
maximum two links are supported.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Add single link PCIe register configurations for no SSC and internal
SSC. Also, add missing PMA lane registers for external SSC.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
PIPE phy status is used to communicate the completion of several PHY
functions. Check if PHY is ready for operation while configured for
PIPE mode during startup.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Check if PMA cmn_ready is set indicating the startup process is complete.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Add PHY PCS common register configuration sequences for single link.
Update single link PCIe register sequence accordingly.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
No functional change. Rename some regmap variables as mentioned in Sierra
register description documentation.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Sierra driver currently supports single link configurations only. Prepare
driver to support multilink multiprotocol configurations along with
different SSC modes.
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Sierra has two PLLs, PLL_CMNLC and PLL_CMNLC1 and each of these PLLs has
two inputs, plllc_refclk (input from pll0_refclk) and refrcv (input from
pll1_refclk). Model PLL_CMNLC and PLL_CMNLC1 as a clock so that it's
possible to select one of these two inputs from device tree.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Add missing clk_disable_unprepare() in cdns_sierra_phy_remove().
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Instead of having separate structure members for each input clock, add
an array for the input clocks within "struct cdns_sierra_phy". This is
in preparation for adding more input clocks required for supporting
additional clock combination.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
No functional change. Group devm_reset_control_get() and
devm_reset_control_get_optional() to a separate function.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
No functional change. Group all devm_clk_get_optional() to a
separate function.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Cadence Sierra PHY driver registers PHY using devm_phy_create()
for all sub-nodes of Sierra device tree node. However Sierra device
tree node can have sub-nodes for the various clocks in addtion to the
PHY. Use devm_phy_create() only for nodes with name "phy" (or "link"
for old device tree) which represent the actual PHY.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Commit 39b823381d ("phy: cadence: Add driver for Sierra PHY")
de-asserts PHY_RESET even before the configurations are loaded in
phy_init(). However PHY_RESET should be de-asserted only after
all the configurations has been initialized, instead of de-asserting
in probe. Fix it here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
The driver enables IPU support. Basically enables the clocks,
timers, watchdog timers and bare minimal MMU and supports
loading the firmware from mmc.
Signed-off-by: Keerthy <j-keerthy@ti.com>
[Amjad: fix compile warnings]
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Add remoteproc resource handling helpers. These functions
are primarily to parse the resource table and to handle
different types of resources. Carveout, devmem, trace &
vring resources are handled.
Signed-off-by: Keerthy <j-keerthy@ti.com>
[Amjad: fix redefinition of "struct resource_table" and compile warnings ]
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Add a reset driver to bring IPs out of reset.
Signed-off-by: Keerthy <j-keerthy@ti.com>
[Amjad: reset_ops structure member "free" has been renamed to "rfree",
use the latter instead]
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
There is a 4 bit VARIANT number inside the JTAGID register that TI
increments any time a new variant for a chip is produced. Each
family of TI's SoCs uses a different versioning scheme based off
that VARIANT number.
CC: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
In Multi DDR subystems with interleaving support, the following needs to
configured,
- interleaving granular size and region
- EMIFs to be enabled
- EMIFs with ecc to be enabled
- EMIF separated or interleaved
- number of cycles of unsuccessful EMIF arbitration to wait before
arbitrating for a different EMIF port, by default set to 3
Add support for configuring all the above by using a MSMC device
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
The current driver only supports single instance of DRR subsystem. Add
support for probing multiple instances of DDR subsystem.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Add a pointer to ddr instance int the lpddr4_privatedata_s structure for
supporting mutliple instances of DDR in the drivers.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
The clock composite is required when using the clock framework. So
select it automatically.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
When regulator consumer attempts to set enabled DVS regulator voltage,
the driver aborts with "Only DVS bucks can be changed when enabled".
In case the regulator is already set to specified voltage, do nothing
instead of failing outright.
When regulator consumer attempts to set enables regulator which cannot
be controlled because it is already always enabled, the driver aborts
with -EINVAL. Again, do nothing in such case and return 0, because the
request is really fulfilled, the regulator is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Initial support for Fairchild's 8 bit I2C gpio expander FXL6408.
The CONFIG_FXL6408_GPIO define enables support for such devices.
Based on: https://patchwork.kernel.org/patch/9148419/
Signed-off-by: Oleksandr Suvorov <cryosay@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
After acking the requested frequency, should wait the ack bit clear
by DDR controller and check the DFS interrupt for next request polling.
Otherwise, the next polling of request bit will get previous value
that DDR controller have not cleared it, so a wrong request frequency
is used.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On i.MX8ULP, The dram config timing need to be saved into sram for
ddr retention when APD enter PD mode, so add this support on i.MX8ULP.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Spi memory operation interface is added to zynq qspi
driver to provide an high-level interface to execute
qspi controller specific memory operations by avoiding
spi_mem_exec_op() from spi-mem framework.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220131052240.23403-5-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add a check afer baudrate calculation to see if the resultant value
falls within the range, else set it to default baudrate value.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220131052240.23403-4-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Read only one byte at a time from txbuf as txbuf may not be
aligned and accessing more than a byte at a time may cause
alignment issues. This fixes the issue of data abort exception
while writing to flash device.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220131052240.23403-3-ashok.reddy.soma@xilinx.com
This patch typecasts and accesses rx buf properly as
an unaligned rxbuf, typecasting with u16 and accessing
it causes data abort exception and this patch fixes it.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220131052240.23403-2-ashok.reddy.soma@xilinx.com
In case fastboot over Ethernet, am65_cpsw_stop() is not called unless
DM_FLAG_OS_PREPARE is set. Without call to am65_cpsw_stop(), DMA
resources are not released thus leading to failures in kernel.
Fix this by adding DM_FLAG_OS_PREPARE flag to am65_cpsw_nuss_port
driver.
Reported-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
If we just use fdtdec_get_addr_size_fixed to get "reg" it will use
64bit address cell to get the base address.
soc {
#address-cells = <1>;
#size-cells = <1>;
compatible ="SiFive,FU500-soc", "fu500-soc", "sifive-soc", "simple-bus";
ranges;
L28: axidma@30010000 {
#dma-cells = <1>;
compatible = "xlnx,axi-dma-1.00.a";
axistream-connected = <&L27>;
axistream-control-connected = <&L27>;
clocks = <&L1>;
interrupt-parent = <&L6>;
interrupts = <32 33>;
reg = <0x30010000 0x4000>;
fdtdec_get_addr_size_fixed: reg: addr=3001000000004000
We should get the base address through its parent's address-cells and
size-cells settings. So we should use fdtdec_get_addr_size_auto_parent()
to get correct base address.
After applying this patch, we can get the correct base address of dma by
replacing fdtdec_get_addr_size_fixed() with
fdtdec_get_addr_size_auto_parent().
fdtdec_get_addr_size_auto_parent:
na=1, ns=1, fdtdec_get_addr_size_fixed: reg: addr=30010000
Signed-off-by: Greentime Hu <greentime.hu@sifive.com>
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Link: https://lore.kernel.org/r/20220120084128.1892101-1-andy.chiu@sifive.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Populate mtd->dev with flash_info->dev which allows to get
full mtd information using the "mtd list" command.
Before, "mtd list" command returns :
List of MTD devices:
* nor0
- type: NOR flash
- block size: 0x40000 bytes
- min I/O: 0x1 bytes
- 0x000000000000-0x000004000000 : "nor0"
After this patch we get for example:
List of MTD devices:
* nor0
- device: flash@0
- parent: spi@40430000
- driver: cfi_flash
- path: /soc/spi@40430000/flash@0
- type: NOR flash
- block size: 0x40000 bytes
- min I/O: 0x1 bytes
- 0x000000000000-0x000004000000 : "nor0"
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Now that all in-tree boards have been converted to the compatible
strings from Linux, delete the support for the ad-hoc "pcf2127-rtc" one.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Allow this driver to be used by boards which inherit their device trees
from Linux. Compatibility is temporarily retained with the old
compatible string which is U-Boot specific, and will be removed after a
few changes.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This seems to be very similar to the already existing PCA9547, save for
the fact that it supports 0.8V and doesn't support 5V. In fact, it is so
similar to the PCA9547 that the NXP LS1028A-RDB board has been driving
this chip using a "nxp,pca9547" compatible string.
Create a new compatible for the PCA9847 (which is the same as in Linux)
and define the same operating parameters for it as for PCA9547.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
The current fixup of LX2160A PCIe nodes is based on non-production
rev1 silicon, and in Linux the nodes have been updated for rev2
silicon, so update the searching compatible string to match the
kernel changes. And for compatibility with the rev1 nodes, move
forward the board specific fixup.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Now that the sunxi_gpio driver handles pull-up/down via the driver
model, pin configuration does not need a platform-specific function.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Tested-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This, along with gpio_flags_xlate(), allows the GPIO driver to handle
pull-up/down flags provided by consumer drivers or in the device tree.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This adds a compatible string for the Allwinner Sun4i-A10 I2C
controller. Without this, boards based on the R8 and A13 (at a
minimum) fail to boot.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Akash Gajjar <gajjar04akash@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The driver for SPI0 on Allwinner H6 SoCs did not use the correct define
SUN50I_GPC_SPI0 for the pin function, but one for a different Allwinner
SoC series.
Fix the conditionals to use the correct define for H6 SoCs. This matches
the conditional logic in the SPL spi driver.
Tested by probing the spi-flash on a pine64_h64-model-b board with
adapted device-tree (disable mmc2, enable spi0).
Signed-off-by: Daniel Wagenknecht <dwagenk@mailbox.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
For printing phys_addr_t we should use %pa to avoid warning like:
drivers/bootcount/bootcount_syscon.c:110:17: note: in expansion of macro ‘dev_err’
110 | dev_err(dev, "%s: Unsupported register size: %d\n", __func__,
| ^~~~~~~
seen for sandbox_defconfig with CONFIG_PHYS_64BIT=y.
Cf. commit 1eebd14b79 ("vsprintf: Add modifier for phys_addr_t")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Align the DFU MTD backend for the UBI partitions with the mtd command write
behavior when the option .dontskipff is not used: don't write the empty
pages (full of 0xFF); it is not required for UBI, see [1] for details.
This patch avoids the "free space fixup" procedure in the kernel [2]
and allows to program a UBIFS volume generated by mkfs.ubifs without the
option -F, --space-fixup.
The MTD DFU backend implements this behavior introduced on DFU NAND
backend by the commit 13cb7cc9e8 ("dfu: Add option to skip empty pages
when flashing UBI images to NAND") and also supported by the command nand
by CONFIG_CMD_NAND_TRIMFFS and by commit c9494866df ("cmd_nand: add nand
write.trimffs command").
[1] http://www.linux-mtd.infradead.org/doc/ubi.html#L_flasher_algo
[2] http://www.linux-mtd.infradead.org/faq/ubifs.html#L_free_space_fixup
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Initially it is set to dev_seq but update to the last bus number is
missing. Fix it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Having U-Boot look up the passed partition name even though an alias
exists is unexpected, leading to warning messages (when the alias name
doesn't exist as a real partition name) or the use of the wrong
partition.
Change part_get_info_by_name_or_alias() to consider real partitions
names only if no alias of the same name exists, allowing to use aliases
to override the configuration for existing partition names.
Also change one use of strcpy() to strlcpy().
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
In DFU v1.1 specification [1] the DFU_UPLOAD (Short Frame)
is handled only in dfuUPLOADIDLE state:
- Figure A.1 Interface state transition diagram
- the state description in chapter A.2
A.2.3 State 2 dfuIDLE
on Receipt of the DFU_UPLOAD request,and bitCanUpload = 1
the Next State is dfuUPLOADIDLE
A.2.10 State 9 dfuUPLOAD-IDLE
When the length of the data transferred by the device in response
to a DFU_UPLOAD request is less than wLength. (Short frame)
the Next State is dfuIDLE
In current code, when an UPLOAD is completely performed after the first
request (for example with wLength=200 and data read = 9), the DFU state
stay at dfuUPLOADIDLE until receiving a DFU_UPLOAD or a DFU_ABORT request
even it is unnecessary as the previous DFU_UPLOAD request already reached
the EOF.
This patch proposes to finish the DFU uploading (don't go to dfuUPLOADIDLE)
and completes the control-read operation (go to DFU_STATE_dfuIDLE) when
the first UPLOAD response has a short frame as an end of file (EOF)
indicator even if it is not explicitly allowed in the DFU specification
but this seems logical.
[1] https://www.usb.org/sites/default/files/DFU_1.1.pdf
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
In case CONFIG_FASTBOOT_FLASH_MMC_DEV == 0, compile-time condition
is not met and fastboot_set_reboot_flag() fails.
Fixes: a362ce214f ("fastboot: Implement generic fastboot_set_reboot_flag")
Signed-off-by: Roman Stratiienko <r.stratiienko@gmail.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
binman support for bintools (binary tools)
minor tools improvements in preparation for FDT signing
various minor fixes and improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmHyEeYRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYYlgf8C7tQVklXz9ZHhxVrFaPHWwgmBzEZJSrc
7SWhDX9yBrAYBUk8Q4OMnJz6nXW8Rz5Td9GfBNWcJag1HjJqno4BxkqwGk2tshgj
GIY0D1cGfKJzB4E6/rK/ETwmX4KVUyEf7S2IdJ0oydkn9t7OwDkUX5WtGXo70E7q
ZJGYlX5NQCVBRAF9NYDuyVFljrPzAiyT58VCtXY3q63C7PmRYvag8r56ug+8lkk3
9EbOTcwETqq9SbT1vucyBxwbUmoKhb2BF32jEcIhozowIM3GNsSpkdzQCUnylqfa
LYI/p0oVTKLfFRBRvQjLgdB/OQP8MLkby8A++Db2OW49mBXhn/5JWA==
=PdpE
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-26jan22' of https://source.denx.de/u-boot/custodians/u-boot-dm
acpi refactoring to allow non-x86 use
binman support for bintools (binary tools)
minor tools improvements in preparation for FDT signing
various minor fixes and improvements
Add support for CDC ACM using the new UDC and gadget API. This protocol
can be used for serial over USB data transfer and is widely supported
by various OS (GNU/Linux, MS-Windows, OSX...). The usual purpose of
such link is to access device debug console and can be useful for
products not exposing regular UART to the user.
A default stdio device named 'usbacm' is created, and can be used
to redirect console to USB link over CDC ACM:
> setenv stdin usbacm; setenv stdout usbacm
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
This commit converts i.MX28's EHCI USB host driver to driver model
(DM_USB). It is a straightforward conversion (to reuse as much code
as possible), based on ehci-mx5.c code.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Those functions will be re-used when the ehci MXS driver (for imx28)
will be converted to also support CONFIG_DM_USB.
No functional changes introduced - only cosmetic changes (u32 type)
and alignment to pass checkpatch.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This function is going to be reused with the CONFIG_DM_USB enabled in
the imx28 mxs USB ehci driver.
No functional changes introduced.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
When building sandbox_defconfig with CONFIG_DM_VIDEO=n a link time error
occurs:
in function `sandbox_serial_pending':
drivers/serial/sandbox.c:101: undefined reference to `video_sync_all'
video_sync_all() is only defined if we have CONFIG_DM_VIDEO=y.
Calling this function in a serial driver looks quite hackish
but at least let's add the missing build constraint.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For whatever reason, usb_setup_ehci_gadget removes and probes USB device
0. However, not all systems have a device 0. Use the first device
instead.
The device probed should probably have something to do with the
controller (as specified by e.g. ums <controller> or fastboot
<controller>). In fact, I find it odd that we probe the USB device in
the first place, because this is just to set up the gadget itself.
Presumably, the controller should be probed by usb_gadget_initialize
somehow.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present this list is used to collect items within the DSDT and SSDT
tables. It is useful for it to collect the whole tables as well, so there
is a list of what was created and which write created each one.
Refactor the code accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the new ACPI writer to write the ACPI tables. At present this is all
done in one monolithic function. Future work will split this out.
Unfortunately the QFW write_acpi_tables() function conflicts with the
'writer' version, so disable that for sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to record the start of an ACPI table so that offsets from
that point can be easily calculated.
Add this to the context and set it before calling the writer method.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this option is missing a header file, a function prototype and
the qfw driver needs a header included.
Fix these problems so we can enable this option on sandbox. This will
increase the build coverage.
Signed-off-by: Simon Glass <sjg@chromium.org>
Register 0x43c in its low 24 bits contains PCI class code.
Update code to set all 24 bits of PCI class code and not only upper 16 bits
of PCI class code.
Use standard U-Boot macro (PCI_CLASS_BRIDGE_PCI << 8) for constructing all
24-bits of PCI class for PCI bridge Normal decode.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Roman Bacik <roman.bacik@broadcom.com>
The write operation in misc_ops already takes a "const void *" buffer,
but misc_write() takes a mutable "void *". There's no reason for this,
so make misc_write() consistent with the standard write() prototype.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use moveconfig.py script to convert define CONFIG_SYS_MAX_FLASH_BANKS
and CONFIG_SYS_MAX_FLASH_BANKS_DETECT to Kconfig and move these entries
to defconfigs.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
[trini: Re-switch to IS_ENABLED check in spi-nor-core.c, re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
Prepare migration to Kconfig.
CONFIG_SYS_MAX_FLASH_BANKS_DETECT becomes boolean and
CONFIG_SYS_MAX_FLASH_BANKS define the MAX size, also used
for detection when CONFIG_SYS_MAX_FLASH_BANKS_DETECT=y
(CFI_MAX_FLASH_BANKS = CONFIG_SYS_MAX_FLASH_BANKS).
CONFIG_SYS_MAX_FLASH_BANKS become mandatory when
CONFIG_SYS_MAX_FLASH_BANKS_DETECT is activated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Replace CONFIG_SYS_MAX_FLASH_BANKS by CFI_FLASH_BANKS to prepare
Kconfig migration and avoid to redefine CONFIG_SYS_MAX_FLASH_BANKS
in cfi_flash.h.
After this patch CONFIG_SYS_MAX_FLASH_BANKS should be never used in
the cfi code: use CFI_MAX_FLASH_BANKS for struct size or CFI_FLASH_BANKS
for number of CFI banks which can be dynamic.
This patch modify all the files which include mtd/cfi_flash.h.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
- fdt_support: Add fdt_for_each_node_by_compatible() helper macro
(Marek)
- turris_omnia: Fixup SATA or PCIe nodes at runtime in DT blob (Pali)
- pci_mvebu: Add support for Kirkwood PCIe controllers (Pali)
- SPL: More verifications for kwbimage in SPL (Pali)
- mvebu: Remove comphy_update_map() (Pali)
- Minor misc stuff
This weak function is not used anymore, so completely remove it.
Private struct comphy_map is not used by any board code anymore, so move it
into private driver header file comphy_core.h.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Placing Unicode control codes <U+0080><U+0093> in the middle of a comment
does not make much sense. Let's get rid of all Unicode in
drivers/ram/octeon/octeon3_lmc.c.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add parameter spl_boot_device to spl_parse_board_header(), which allows
the implementations to see from which device we are booting and do
boot-device-specific checks of the image header.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Kirkwood uses macros KW_DEFADR_PCI_MEM and KW_DEFADR_PCI_IO for base
address of PCIe mappings. Size of PCIe windows is not defined in any macro
yet, so export them in new KW_DEFADR_PCI_MEM_SIZE and KW_DEFADR_PCI_IO_SIZE
macros.
Kirkwood arch code already maps mbus windows for io and mem, so avoid
calling mvebu_mbus_add_window_by_id() function which would try to do
duplicate window mapping.
Kirkwood PCIe controllers already use "marvell,kirkwood-pcie" DT compatible
string, so mark pci_mvebu.c driver as compatible for it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add macro fdt_for_each_node_by_compatible() to allow iterating over
fdt nodes by compatible string.
Convert various usages of
off = fdt_node_offset_by_compatible(fdt, start, compat);
while (off > 0) {
code();
off = fdt_node_offset_by_compatible(fdt, off, compat);
}
and similar, to
fdt_for_each_node_by_compatible(off, fdt, start, compat)
code();
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYeg7sQAKCRDKSWXLKUoM
IVhJAKCAiNx/joEeFBJ0XgThtJzFhCjdMwCfYKY9Ewz4L0n2I56lDgR3UJroct0=
=HtB+
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.04-rc1
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
Power domain driver sends PM fragment to PMUFW. It is sent for every node
which is listed in DT. But some nodes could be already enabled but driver
is not capable to find it out. That's why it blinly sents request for every
listed IP. When PMUFW response by XST_PM_ALREADY_CONFIGURED error code
there is no need to show any error message because node is already enabled.
That's why cover this case with message when DEBUG is enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/8c15ef0b68cf191f693d3d010f70ac24cfd8171f.1642163135.git.michal.simek@xilinx.com
The clock delay of the RMII/RGMII interface is controlled by SCU340~35C.
These values are obtained by measurement and experiments so we simply
use macro to define them.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add support of the MAC controller of Aspeed AST2600 SOC. The MAC
controller is the same with AST2500, except it has stand-alone MDIO
hardware block.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add support for DM_MDIO to connect to PHY. For the systems that have a
stand-alone MDIO hardware block, enable CONFIG_DM_MDIO to use driver
model for MDIO devices.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This commit adds SD/MMC clocks, and provides .set/get_rate callbacks
for SD/MMC device present on Actions OWL S700 SoCs.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This commit introduces get/set_rate callbacks, these are dummy at
the moment, and can be used to get/set clock for various devices
based on the clk id.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Changes to the am33xx device (33e9021a) trees have been merged in from
the upstream linux kernel which now means the device tree uses the new
pins format (as of 5.10) where the confinguration can be stores as a
separate configuration value and pin mux mode which are then OR'd
together.
This patch adds support for the new format to u-boot so that
pinctrl-cells is now respected when reading in pinctrl-single,pins
Signed-off-by: Anthony Bagwell <anthony.bagwell@hivehome.com>
Fix fastboot flash bug.
If the downloading file size is equal to the partition size, "fastboot
flash" can't work, at least in sunxi platform, because used an
uninitalized point: ep->desc.
This patch also fixed 'data abort' bug in am335x platform.
Reproduce: fastboot flash loader1 spl/sunxi-spl.bin.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Currently the pxa3xx driver does not set the udevice in the mtd_info
struct and this prevents the mtd from parsing the partitions via DTS
like for SPI-NOR.
So simply set the mtd->dev to the driver udevice.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
- Let am335x_evm use the CPSW or PRUSS ethernet.
- Implement timer_get_boot_us in the omap timer driver
- gpmc bitflip, QSPI clock calculation on am437x, da8xx_gpio bugfixes
- Assorted K3 updates
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmHlNOccHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyL0JB/4+sKNWPMgOYvP2uLCC
euRGomhxJ5WmxJVDtJeBIRg0YKSkwnE8JwIN2qqGu15xJnNX9Ck5qnIMPbiZ/io9
ocW5Z/4C4rfJX/OzD6FtmbMNsvG/umVmZkjRU3ryRXKGyNVpVjLQ2EEECaJfk1WZ
Nd/J6/Jo8nafb1x4OeY+F6+xwZAuj7Mrun9SsDSyrIvmEqSnaQNioj+lStkauL51
NwQgBxZBQmbdCgF7Ooy6rYlXZBR6r/rgWB9n3RP8emDCwfCMul9HOMT432oKNbhW
bGrcMu9AWv/pgzXogxSzYbEdTAnoVEODtU1suCa8LV6KJPEG693gARnRm/KjvPHa
FfsK
=39IY
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.04-b' of https://source.denx.de/u-boot/custodians/u-boot-at91
Second set of u-boot-at91 features for the 2022.04 cycle:
This small feature set includes few changes for sama7g5 and sama7g5ek:
turn blue led on at boot, changes required for the Rev4 of the board,
better sync with the Linux DT with regards to the new DT nodes.
