Commit graph

3691 commits

Author SHA1 Message Date
Kishon Vijay Abraham I
29171dcfaa mmc: omap_hsmmc: Fix incorrect bit operations for disabling a bit
omap_hsmmc driver uses "|" in a couple of places for disabling a bit.
While it's okay to use it in "mmc_reg_out" (since mmc_reg_out has a
_mask_ argument to take care of resetting a bit), it's incorrectly used
for resetting flags in "omap_hsmmc_send_cmd".

Fix it here by using "&= ~()" to reset a bit.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-01-19 15:49:23 -05:00
Kishon Vijay Abraham I
f0d53e88a6 mmc: omap_hsmmc: Add support for DMA (ADMA2)
The omap hsmmc host controller can have the ADMA2 feature. It brings better
read and write throughput.
On most SOC, the capability is read from the hl_hwinfo register. On OMAP3,
DMA support is compiled out.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-01-19 15:49:17 -05:00
Jean-Jacques Hiblot
f844d5f4e6 omap: Update the base address of the MMC controllers
Align the base address defined in header files with the base address used
in the DTS. This will facilitate the introduction of the DMA support.

Of all HSMMC users, only omap3 doesn't have the 0x100 reserved region at
the top. This region will be used to determine if the controller supports
DMA transfers

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-01-18 22:04:21 -05:00
Jean-Jacques Hiblot
741726ae4c Revert "omap_hsmmc: update struct hsmmc to accommodate omap3 from DT"
This reverts commit 46831c1a4c.
This reserved area at the beginning of struct hsmm, will be used later to
support ADMA

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-01-18 22:04:21 -05:00
Tom Rini
8e9801c283 Merge git://git.denx.de/u-boot-imx 2018-01-15 16:44:18 -05:00
Bryan O'Donoghue
aeae70fac5 arm: imx: hab: Define rvt_failsafe()
The hab_rvt_failsafe() callback according to the HABv4 documentation:

"This function provides a safe path when image authentication has failed
and all possible boot paths have been exhausted. It is intended for use by
post-ROM boot stage components, via the ROM Vector Table."

Once invoked the part will drop down to its BootROM USB recovery mode.
Should it be the case that the part is in secure boot mode - only an
appropriately signed binary will be accepted by the ROM and subsequently
executed.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-14 17:26:30 +01:00
Bryan O'Donoghue
07eefaf16e arm: imx: hab: Make imx_hab_is_enabled global
It will be helpful to boot commands to know if the HAB is enabled. Export
imx_hab_is_enabled() now to facilitate further work with this data-point in
a secure-boot context.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-14 17:26:30 +01:00
Bryan O'Donoghue
57f6548606 arm: imx: hab: Prefix authenticate_image with imx_hab
Tidy up the HAB namespace a bit by prefixing external functions with
imx_hab. All external facing functions past this point will be prefixed in
the same way to make the fact we are doing IMX HAB activities clear from
reading the code. authenticate_image() could mean anything
imx_hab_authenticate_image() is on the other hand very explicit.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-14 17:26:30 +01:00
Bryan O'Donoghue
1addedadc4 arm: imx: hab: Define rvt_check_target()
The hab_rvt_check_target() callback according to the HABv4 documentation:

"This function reports whether or not a given target region is allowed for
 either peripheral configuration or image loading in memory. It is intended
 for use by post-ROM boot stage components, via the ROM Vector Table, in
 order to avoid configuring security-sensitive peripherals, or loading
 images over sensitive memory regions or outside recognized memory devices
 in the address map."

It is a useful function to support as a precursor to calling into
authenticate_image() to validate the target memory region is good.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-14 17:26:30 +01:00
Bryan O'Donoghue
cd2d46003c arm: imx: hab: Add IVT header definitions
The various i.MX BootROMs containing the High Assurance Boot (HAB) block
rely on a data structure called the Image Vector Table (IVT) to describe to
the BootROM where to locate various data-structures used by HAB during
authentication.

This patch adds a definition of the IVT header for use in later patches,
where we will break the current incorrect dependence on fixed offsets in
favour of an IVT described parsing of incoming binaries.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-14 17:26:30 +01:00
Bryan O'Donoghue
c5800b2541 arm: imx: hab: Fix authenticate_image input parameters
u-boot command "hab_auth_img" tells a user that it takes

- addr - image hex address
- offset - hex offset of IVT in the image

but in fact the callback hab_auth_img makes to authenticate_image treats
the second 'offset' parameter as an image length.

Furthermore existing code requires the IVT header to be appended to the end
of the image which is not actually a requirement of HABv4.

This patch fixes this situation by

1: Adding a new parameter to hab_auth_img
   - addr   : image hex address
   - length : total length of the image
   - offset : offset of IVT from addr

2: Updates the existing call into authenticate_image() in
   arch/arm/mach-imx/spl.c:jump_to_image_no_args() to pass
   addr, length and IVT offset respectively.

This allows then hab_auth_img to actually operate the way it was specified
in the help text and should still allow existing code to work.

It has the added advantage that the IVT header doesn't have to be appended
to an image given to HAB - it can be prepended for example.

Note prepending the IVT is what u-boot will do when making an IVT for the
BootROM. It should be possible for u-boot properly authenticate images
made by mkimage via HAB.

This patch is the first step in making that happen subsequent patches will
focus on removing hard-coded offsets to the IVT, which again is not
mandated to live at the end of a .imx image.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-14 17:26:30 +01:00
Bryan O'Donoghue
08a81cad2f arm: imx: hab: Move CSF_PAD_SIZE to hab.h
CSF_PAD_SIZE should be defined in hab.h, move it to that location now.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-14 17:26:30 +01:00
Bryan O'Donoghue
191d8bd509 arm: imx: hab: Move IVT_SIZE to hab.h
The size of the IVT header should be defined in hab.h move it there now.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-14 17:26:30 +01:00
Bryan O'Donoghue
adbb051f08 arm: imx: hab: Make authenticate_image return int
Both usages of authenticate_image treat the result code as a simple binary.
The command line usage of authenticate_image directly returns the result
code of authenticate_image as a success/failure code.

Right now when calling hab_auth_img and test the result code in a shell a
passing hab_auth_img will appear to the shell as a fail.

The first step in fixing this behaviour is to fix-up the result code return
by authenticate_image() itself, subsequent patches fix the interpretation
of authenticate_image so that zero will return CMD_RET_SUCCESS and non-zero
will return CMD_RET_FAILURE.

The first step is fixing the return type in authenticate_image() so do that
now.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-14 17:26:30 +01:00
Stephen Warren
8163faf952 ARMv8: add optional Linux kernel image header
Allow placing a Linux kernel image header at the start of the U-Boot
binary. This is useful since the image header reports the amount of memory
(BSS and similar) that U-Boot needs to use, but that isn't part of the
binary size. This can be used by the code that loads U-Boot into memory to
determine where to load U-Boot, based on other users of memory.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2018-01-12 09:52:11 -07:00
Tom Rini
1a62f8597c Merge git://git.denx.de/u-boot-video 2018-01-11 13:43:36 -05:00
Tom Rini
6bf634223a Merge git://git.denx.de/u-boot-fsl-qoriq 2018-01-11 11:18:49 -05:00
Tom Rini
e38c66edae Merge git://git.denx.de/u-boot-usb 2018-01-11 11:18:29 -05:00
Hannes Schmelzer
3215192922 mach-omap2: add AM335x Display PLL register definition
Adds the register definition of the Display DPLL

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
2018-01-11 15:16:34 +01:00
Sumit Garg
1cabeb88eb ls1088ardb: Add SD Secure boot target support
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
[YS: run moveconfig.py -s]
Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-10 12:32:45 -08:00
Ahmed Mansour
44262327aa drivers/misc: Share qbman init between archs
This patch adds changes necessary to move functionality present in
PowerPC folders with ARM architectures that have DPAA1 QBMan hardware

- Create new board/freescale/common/fsl_portals.c to house shared
  device tree fixups for DPAA1 devices with ARM and PowerPC cores
- Add new header file to top includes directory to allow files in
  both architectures to grab the function prototypes
- Port inhibit_portals() from PowerPC to ARM. This function is used in
  setup to disable interrupts on all QMan and BMan portals. It is
  needed because the interrupts are enabled by default for all portals
  including unused/uninitialised portals. When the kernel attempts to
  go to deep sleep the unused portals prevent it from doing so

Signed-off-by: Ahmed Mansour <ahmed.mansour@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-10 12:28:47 -08:00
Yuantian Tang
1b76f3b8ab armv8: layerscape: sata: refine port register configuration
Sata registers PP2C and PP3C are used to control the configuration
of the PHY control OOB timing for the COMINIT/COMWAKE parameters
respectively. Calculate those parameters from port clock frequency.
Overwrite those registers with calculated values to get better OOB
timing.

Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-10 12:28:14 -08:00
Patrice Chotard
c8f787760e board: stm32f429-disco: switch to DM STM32 pinctrl and gpio driver
Use available DM stm32f7_gpio.c and pinctrl_stm32.c drivers
instead of board GPIO initialization.

Remove stm32_gpio.c which is no more used and migrate
structs stm32_gpio_regs and stm32_gpio_priv into
arch-stm32f4/gpio.h to not break compilation.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-01-10 08:05:46 -05:00
Patrice Chotard
4a56fd484a board: stm32f429-disco: switch to DM STM32 clock driver
Use available DM clk_stm32f.c driver instead of dedicated
mach-stm32/stm32f4/clock.c.

Migrate periph_clock defines from stm32_periph.h directly in
CLK driver. These periph_clock defines will be removed when STMMAC,
TIMER2 and SYSCFG drivers will support DM CLK.

Enable also CLK flag.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-01-10 08:05:46 -05:00
Patrice Chotard
2d18d72858 board: stm32f429-disco: switch to DM STM32 serial driver
Remove serial_stm32.c driver and uart init from board file,
use available DM serial_stm32x7.c driver compatible for
STM32F4/F7 and H7 SoCs.

The serial_stm32x7.c driver will be renamed later with a more
generic name as it's shared with all STM32 Socs.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-01-10 08:05:46 -05:00
Eddie Cai
bf2b72bef1 usb: rockchip: add the rockusb gadget
this patch implement rockusb protocol on the device side. this is based on
USB download gadget infrastructure. the rockusb function implements the rd,
wl, rid commands. it can work with rkdeveloptool

Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-01-10 11:11:05 +01:00
Elaine Zhang
538f67c332 rockchip: clk: bind reset driver
Bind rockchip reset to clock-controller with rockchip_reset_bind().

Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-01-09 11:13:32 +01:00
Stefan Agner
46718353b2 imx: initialize and use generic timer on i.MX 6UL/ULL
The i.MX 6UL/ULL feature a Cortex-A7 CPU which suppor the ARM
generic timer. This change makes use of the ARM generic timer in
U-Boot.

This is crucial to make the ARM generic timers usable in Linux since
timer_init() initalizes the system counter module, which is necessary
to use the generic timers CP15 registers.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-08 17:33:06 +01:00
Fabio Estevam
290e7cfdbf mx6ull: Handle the CONFIG_MX6ULL cases correctly
Since commit 051ba9e082 ("Kconfig: mx6ull: Deselect MX6UL from
CONFIG_MX6ULL") CONFIG_MX6ULL does not select CONFIG_MX6UL anymore, so
take this into consideration in all the checks for CONFIG_MX6UL.

This fixes a boot regression.

Reported-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Breno Lima <breno.lima@nxp.com>
Tested-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Tested-by: Jörg Krause <joerg.krause@embedded.rocks>
2018-01-04 16:29:04 +01:00
Eran Matityahu
af104ae5b8 imx: spl: Fix NAND bootmode detection
commit 20f1471416 ("imx: spl: Update NAND bootmode detection bit")
broke the NAND bootmode detection by checking if
BOOT_CFG1[7:4] == 0x8 for NAND boot mode.
This commit essentially reverts it, while using the IMX6_BMODE_*
macros that were introduced since.

Tables 8-7 & 8-10 from IMX6DQRM say the NAND boot mode selection
is done when BOOT_CFG1[7] is 1, but BOOT_CFG1[6:4] is not
necessarily 0x0 in this case.
Actually, NAND boot mode is when 0x8 <= BOOT_CFG1[7:4] <= 0xf,
like it was in the code before.

Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Tim Harvey <tharvey@gateworks.com>
2018-01-03 14:01:38 +01:00
Fabio Estevam
4555c26142 imx: Add a common way for detecting NXP boards revision
NXP development boards based on i.MX6/i.MX7 contain the board
revision information stored in the fuses.

Introduce a common function that can be shared by different boards and
convert mx6sabreauto to use this new mechanism.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-12-29 11:18:59 +01:00
Tom Rini
eeab579aa8 Merge git://git.denx.de/u-boot-rockchip 2017-12-18 18:39:18 -05:00
Tom Rini
1a3fc354b5 Merge git://git.denx.de/u-boot-fsl-qoriq 2017-12-18 18:39:00 -05:00
Kever Yang
270288544e rockchip: update boot0 hook
Rockchip SoCs only need boot0 hook at SPL, and the U-Boot proper do not
need it.

The very beginning of U-Boot proper is different between armv7 and armv8:
armv7 start with ARM_VECTORS while armv8 start with 'b reset'.

Here is the map of very beginning for all cases:
armv7 SPL: TAG(overwrite 'b 1f')+'b reset' + ARM_VECTORS
armv7 U-Boot: ARM_VECTORS
armv8 SPL: TAG(overwrite 'b 1f')+'b reset' + Reserved_iram(rk3399)
armv8 U-Boot: 'b reset'

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-12-18 16:56:05 +01:00
Michal Simek
2d2af5d834 arm64: zynqmp: Add missing zynq_board_read_rom_ethaddr() prototype
Add missing zynq_board_read_rom_ethaddr() prototype reported by sparse.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
2017-12-14 20:08:44 +01:00
Wenbin song
a8f33034f2 armv8: ls1043a/ls2080a: check SoC by device ID
Check LS1043A/LS2080a by device ID without using personality ID to
determine revision number. This check applies to all various
personalities of the same SoC family.

Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-13 13:40:29 -08:00
Tuomas Tynkkynen
a72c618068 ARM: pxa: Remove unused ifdefs
These ifdefs are protecting #include statements for files that have
never existed. AFAICT this hardware.h has been copied from the kernel
and the ifdefs have never served a role in U-Boot, so delete them.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-12-12 21:34:10 -05:00
Tuomas Tynkkynen
b82e667f79 ata: Migrate CONFIG_LIBATA to Kconfig
This symbol enables some library code used by various SATA drivers,
so make this a non-user-visible symbol select'ed by the respective
drivers, and let moveconfig handle the rest.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-12-12 18:16:05 -05:00
Tuomas Tynkkynen
9fd95ef0d3 ata: Migrate CONFIG_SCSI_AHCI to Kconfig
And use 'imply' liberally.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-12-12 18:13:19 -05:00
Tom Rini
0c4d24823e Merge git://git.denx.de/u-boot-uniphier 2017-12-04 10:24:35 -05:00
Peng Fan
90351547ce armv8: mmu: fix page table mapping
To page mapping the lowest 2 bits needs to be 0x3.
If not fix this, the final lowest 3 bits for page mapping is 0x1
which is marked as reserved.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-04 10:23:52 -05:00
Neil Armstrong
c7be3e5a79 ARM: arch-meson: build memory banks using reported memory from registers
As discussed at [1], the Amlogic Meson GX SoCs can embed a BL31 firmware
and a secondary BL32 firmware.
Since mid-2017, the reserved memory address of the BL31 firmware was moved
and grown for security reasons.

But mainline U-Boot and Linux has the old address and size fixed.

These SoCs have a register interface to get the two firmware reserved
memory start and sizes.

This patch adds a dynamic reservation of the memory zones in the device tree bootmem
reserved memory zone used by the kernel in early boot.
To be complete, the memory zones are also added to the EFI reserved zones.

Depends on patchset "Add support for Amlogic GXL Based SBCs" at [2].

[1] http://lists.infradead.org/pipermail/linux-amlogic/2017-October/004860.html
[2] http://lists.infradead.org/pipermail/linux-amlogic/2017-November/005410.html

Changes since v1:
- switched the #if to if(IS_ENABLED()) to compile all code paths
- renamed function to meson_board_add_reserved_memory()
- added a mem.h header with comment
- updated all boards ft_board_setup()

Changes since RFC v2:
- reduced preprocessor load
- kept Odroid-C2 static memory mapping as exception

Changes since RFC v1:
- switch to fdt rsv mem table and efi reserve memory
- replaced in_le32 by readl()

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[trini: Fix warning on khadas-vim over missing <asm/arch/mem.h>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-12-04 10:17:29 -05:00
Neil Armstrong
6915b10331 ARM: arch-meson: add ethernet common init function
Introduce a generic common Ethernet Hardware init function
common to all Amlogic GX SoCs with support for the
Internal PHY enable for GXL SoCs.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2017-12-04 09:59:02 -05:00
Masahiro Yamada
6ae3900a86 mtd: nand: Rename nand.h into rawnand.h
This header was renamed to rawnand.h in Linux.

The following is the corresponding commit in Linux.

  commit d4092d76a4a4e57b65910899948a83cc8646c5a5
  Author: Boris Brezillon <boris.brezillon@free-electrons.com>
  Date:   Fri Aug 4 17:29:10 2017 +0200

      mtd: nand: Rename nand.h into rawnand.h

      We are planning to share more code between different NAND based
      devices (SPI NAND, OneNAND and raw NANDs), but before doing that
      we need to move the existing include/linux/mtd/nand.h file into
      include/linux/mtd/rawnand.h so we can later create a nand.h header
      containing all common structure and function prototypes.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-12-04 22:00:00 +09:00
Philipp Tomsich
4fc495e9e2 rockchip: clk: rk3128: fix DCLK_VOP_DIV_CON_MASK
The DCLK_VOP_DIV_CON_MASK should cover only bits 8 through 15.
Fix this to remove an "integer-overflow on shifted constant" warning.

Fixes: 9246d9e ("rockchip: rk3128: add clock driver")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-12-02 00:27:42 +01:00
Philipp Tomsich
cd401abcd5 rockchip: clk: rk3128: fix NANDC_PLL_SEL_MASK
The PLL selector field for NANDC is only 2 bits wide.
This fixes an 'int-overflow on shift' warning.

Fixes: 9246d9e ("rockchip: rk3128: add clock driver")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-12-02 00:27:31 +01:00
Kever Yang
e129c480e4 rockchip: rk3128: add pinctrl driver
Add rk3128 pinctrl driver and grf/iomux structure definition.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-30 22:55:26 +01:00
Kever Yang
9246d9e541 rockchip: rk3128: add clock driver
Add rk3128 clock driver and cru structure definition.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-30 22:55:26 +01:00
Patrice Chotard
014a953c4a stm32: migrate clock structs in include/stm32_rcc.h
In order to factorize code between STM32F4 and STM32F7
migrate all structs related to RCC clocks in include/stm32_rcc.h

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
2017-11-29 22:30:50 -05:00
Patrice Chotard
4e97e25723 clk: clk_stm32fx: add clock configuration for mmc usage
MMC block needs 48Mhz source clock, for that we choose
to select the SAI PLL.
Update also stm32_clock_get_rate() to retrieve the MMC
clock source needed in MMC driver.

STM32F4 uses a different RCC variant than STM32F7. For STM32F4
sdmmc clocks bit are located into dckcfgr register whereas there
are located into dckcfgr2 registers on STM32F7.
In both registers, bits CK48MSEL and SDMMC1SEL are located at
the same position.

Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
2017-11-29 22:30:50 -05:00
Patrice Chotard
c88c6a9e03 clk: stm32fx: migrate define from rcc.h to driver
STM32F4 doesn't get rcc.h file, to avoid compilation
issue, migrate RCC related defines from rcc.h to driver
file and remove rcc.h file.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
2017-11-29 22:30:50 -05:00
Patrice Chotard
d0a768b1c8 clk: stm32f7: retrieve PWR base address from DT
PWR IP is used to enable over-drive feature in
order to reach a higher frequency.
Get its base address from DT instead of hard-coded value

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
2017-11-29 22:30:50 -05:00
Tom Rini
b06c46de63 Xilinx changes for v2018.1
Zynq:
 - Add support for Syzygy and cc108 boards
 - Add support for mini u-boot configurations (cse)
 - dts updates
 - config/defconfig updates in connection to Kconfig changes
 - Fix psu_init handling
 
 ZynqMP:
 - SPL fixes
 - Remove slcr.c
 - Fixing r5 startup sequence
 - Add support for external pmufw
 - Add support for new ZynqMP chips
 - dts updates
 - Add support for zcu102 rev1.0 board
 
 Drivers:
 - nand: Support external timing setting and board init
 - ahci: Fix wording
 - axi_emac: Wait for bit, non processor mode, readl/write conversion
 - zynq_gem: Fix SGMII/PCS support
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iEYEABECAAYFAloeqWoACgkQykllyylKDCHO1wCggsSgQqOPdCo207FqI3yj2p0E
 MYkAoI1wKvQcjGJJY19YEC1r70Op8RNo
 =BqNN
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2018.01' of git://www.denx.de/git/u-boot-microblaze

Xilinx changes for v2018.1

Zynq:
- Add support for Syzygy and cc108 boards
- Add support for mini u-boot configurations (cse)
- dts updates
- config/defconfig updates in connection to Kconfig changes
- Fix psu_init handling

ZynqMP:
- SPL fixes
- Remove slcr.c
- Fixing r5 startup sequence
- Add support for external pmufw
- Add support for new ZynqMP chips
- dts updates
- Add support for zcu102 rev1.0 board

Drivers:
- nand: Support external timing setting and board init
- ahci: Fix wording
- axi_emac: Wait for bit, non processor mode, readl/write conversion
- zynq_gem: Fix SGMII/PCS support
2017-11-29 08:26:07 -05:00
Masahiro Yamada
ed3986ca30 bitops: collect BIT macros to include/linux/bitops.h
Same macros are defined in various places.  Collect them into
include/linux/bitops.h like Linux.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-11-29 00:28:57 +09:00
Michal Simek
494fffe70d arm64: zynqmp: Add support for CG/EG/EV device detection
Version string has unused fields 31:20 which can be used for exporting 9
bits from efuse IPDISABLE regs to recognize eg/cg/ev devices.

These efuse bits are setup for certain devices.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:01 +01:00
Siva Durga Prasad Paladugu
e042d36e17 arm64: zynqmp: Provide a Kconfig option to use specified memory for MMU table
This patch provides a Kconfig option to use specified
memory for MMU table using reserve_mmu platform specific
routine. Here we used TCM space for MMU table.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:08:56 +01:00
Michal Simek
62e950fad3 arm64: zynqmp: Remove slcr with mio status pin detection
This code is not used on this platform and it is not called.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:08:55 +01:00
Tom Rini
6e6cf015e7 Merge git://www.denx.de/git/u-boot-imx
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-27 07:22:11 -05:00
Fabio Estevam
e2162d709f imx: Remove boolean parameter from wdog powerdown function
imx_set_wdog_powerdown() is always used to disable the power down
enable bit, so remove the boolean parameter of the function.

It is also a bit strange to write a boolean value into registers,
so this new version makes explicit that we are writing 0.

While at it, rename it to imx_wdog_disable_powerdown().

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-11-27 10:34:49 +01:00
Fabio Estevam
23ecca2cd8 mx6ull: Fix WDOG3 base address
i.MX6ULL has the same WDOG3 base address as i.MX6UL, so take this
into account in the base address definition.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-11-27 10:34:31 +01:00
Philipp Tomsich
8c2bb589e2 rockchip: pinctrl: rk3399: add support for I2C8
The RK3399 has a total of 9 I2C controllers.  To support these, the
enum in periph.h is extended and the mapping from the IRQ numbers to
the peripheral-ids is extended to ensure that pinctrl requests are
passed through to the function configuring the I2C pins.

For I2C8, the pinctrl is implemented and tested (on a RK3399-Q7) using
communication with the FAN53555 connected on I2C8.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
2017-11-26 00:39:08 +01:00
Andy Yan
b4d23f7643 rockchip: add support for enter to bootrom download mode
Rockchip bootrom will enter download mode if it returns from
spl/tpl with a non-zero value and couldn't find a valid image
in the backup partition.
This patch provide a method to instruct the system to back to
bootrom download mode by checking the BROM_DOWNLOAD_FLAG register.
As the bootrom download function relys on some modules such as
interrupts, so we need to back to bootrom as early as possbile
before the tpl/spl code override the interrupt configurations.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:23 +01:00
Andy Yan
e3067793c3 rockchip: make boot_mode related codes reused across all platforms
setup_boot_mode function use the same logic but different
mode register address across all the rockchip platforms,
so it's better to make this function reused across all the
platforms, and let the mode register address setting from
the config file.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:23 +01:00
Kever Yang
6ba54058ed rockchip: sysreset: merge into one common driver
Use a common driver for all Rockchip SOC instead of one for each SoC.
Use driver_data for reg offset.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:23 +01:00
Philipp Tomsich
b82bd1f8d4 rockchip: back-to-bootrom: allow passing a cmd to the bootrom
The BROM supports forcing it to enter download-mode, if an appropriate
result/cmd-word is returned to it.  There already is a series to
support this in review, so this prepares the (newly C-version) of the
back-to-bootrom code to accept a cmd to passed on to the BROM.

All the existing call-sites are adjusted to match the changed function
signature.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
2017-11-21 23:57:22 +01:00
Philipp Tomsich
ecfd71891a rockchip: back-to-bootrom: replace assembly-implementation with C-code
The back-to-bootrom implementation for Rockchip has always relied on
the stack-pointer being valid on entry, so there was little reason to
have this as an assembly implementation.

This provides a new C-only implementation of save_boot_params and
back_to_bootrom (relying on setjmp/longjmp) and removes the older
assembly-only implementation.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
2017-11-21 23:57:22 +01:00
Philipp Tomsich
b4806d6f1f arm: provide a PCS-compliant setjmp implementation
The previous setjmp-implementation (as a static inline function that
contained an 'asm volatile' sequence) was extremely fragile: (some
versions of) GCC optimised the set of registers.  One critical example
was the removal of 'r9' from the clobber list, if -ffixed-reg9 was
supplied.

To increase robustness and ensure PCS-compliant behaviour, the setjmp
and longjmp implementation are now in assembly and closely match what
one would expect to find in a libc implementation.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
2017-11-21 23:57:22 +01:00
Philipp Tomsich
7776cc011d arm: make save_boot_params_ret prototype visible for AArch64
The save_boot_params_ret() prototype (for those of us, that have a
valid SP on entry and can implement save_boot_params() in C), was
previously only defined for !defined(CONFIG_ARM64).

This moves the declaration to a common block to ensure the prototype
is available to everyone that might need it.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
2017-11-21 23:57:22 +01:00
Philipp Tomsich
b377d22264 rockchip: boot0 hook: support early return for RK3188/RK3066-style BROM
Some Rockchip BROM versions (e.g. the RK3188 and RK3066) first read 1KB data
from NAND into SRAM and executes it. Then, following a return to bootrom, the
BROM loads additional code to SRAM (not overwriting the first block read) and
reenters at the same address as the first time.

To support booting either a TPL (on the RK3066) or SPL (on the RK3188) using
this model of having to count entries, this commit adds code to the boot0
hook to track the number of entries and handle them accordingly.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
2017-11-21 23:57:22 +01:00
Philipp Tomsich
16d761e3dd bcm281xx: boot0 hook: adjust to unified boot0 semantics
This updates the BCM281xx boot0-hook to the updated boot0 semantics
by emitting _start and the vector table before the boot0 hook (as
was the case before).

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:22 +01:00
Philipp Tomsich
62269f02ab bcm235xx: boot0 hook: adjust to unified boot0 semantics
This updates the BCM235xx boot0-hook to the updated boot0 semantics
by emitting _start and the vector table before the boot0 hook (as
was the case before).

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

Version-changes: 5
- ran 'whitespace-cleanup'
2017-11-21 23:57:21 +01:00
Kever Yang
cee7470cd8 rockchip: boot0: align to 0x20 for armv7 '_start'
The '_start' is using as vector table base address, and will write
to VBAR register, so it needs to be aligned to 0x20 for armv7.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[Updated to current code base:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:21 +01:00
Philipp Tomsich
ef70a42f0f arm: boot0 hook: move boot0 hook before '_start'
The boot0 hook on ARM does not insert its payload before the vector
table. This is both a mismatch with thec comment above it and
contradict usage of the boot0 hook on ARM64.

To fix this (and unify the semantics for ARM and ARM64), we change the
boot0-hook semantics on ARM to match those on ARM64:
  (1) if a boot0-hook is present it is inserted at the start of
      the image
  (2) if a boot0-hook is present, emitting the ARM vector table
      (and the _start) symbol are suppressed in vectors.S and
      the boot0-hook has full control over where and when it
      wants to emit these

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:21 +01:00
Beniamino Galvani
456efb5127 odroid-c2: enable I2C
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
2017-11-20 10:11:44 +01:00
Beniamino Galvani
f8d9ca1833 i2c: add Amlogic Meson driver
Add a driver for the I2C controller available on Amlogic Meson SoCs.

Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
2017-11-20 10:11:34 +01:00
Martyn Welch
54d8d4942f arm: mx5: Add more register definitions
Add register definitions require for video configuration.

Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-11-20 09:58:31 +01:00
Martyn Welch
065a1ece7a pwm: imx: Enable PWM support on i.MX53
Add missing parts for i.MX53 PWM support

Acked-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2017-11-20 09:58:31 +01:00
Landheer-Cieslak, Ronald
48c7f77128 Add UART base addresses for additional UARTs
UARTs 1 through 5 were missing in the code - added.
Also pick the default according to the configuration setting for the
console index.

Signed-off-by: Ronald Landheer-Cieslak <ronaldlandheercieslak@eaton.com>
2017-11-17 10:53:45 -05:00
Stephen Warren
49e93875a6 arm64: support running at addr other than linked to
This is required in the case where U-Boot is typically loaded and run at
a particular address, but for some reason the RAM at that location is not
available, e.g. due to memory fragmentation loading other boot binaries or
firmware, splitting an SMP complex between various different OSs without
using e.g. the EL2 second-stage page tables to hide the memory asignments,
or due to known ECC failures.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2017-11-17 07:44:13 -05:00
Neil Armstrong
ea990816fe arm: meson: Add supplementary ethernet registers definitions
On Amlogic Meson GXL/GXM, supplementary ethernet configuration registers
were added to configure the internal RMII PHY interface.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2017-11-17 07:44:13 -05:00
Felix Brack
c07bf9bea7 am33xx: Add a function to query MPU voltage in uV
For the DM TPS65910 driver I'm working on, querying the MPU voltage
should return a value in uV. This value can then be used by the
regulator's standard function set_value to set the MPU voltage.

Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-11-17 07:43:32 -05:00
Lukasz Majewski
9c8979cdb7 imx7: Add include guards for include/asm/arch-mx7/sys_proto.h file
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-09 11:32:49 +01:00
Lukasz Majewski
e895e996ab imx5: Add include guards for include/asm/arch-mx5/sys_proto.h file
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-09 11:32:49 +01:00
Lukasz Majewski
90d0e38c1e imx6: Add include guards for include/asm/arch-mx6/sys_proto.h file
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-09 11:32:49 +01:00
Lukasz Majewski
ec1b26973c imx6: iomux: Add generic function to set RGMII IO voltage on IMX6 SoCs
This commit provides generic function to set the RGMII/HSIC IO voltage
level on iMX6 devices.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-09 11:32:49 +01:00
Patrice Chotard
e36591c350 spear: fix STMicroelectronics copyright
Uniformize STMicroelectronics copyrights headers for SPEAR
related code.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-11-06 09:51:01 -05:00
Patrice Chotard
1537d38619 stv0991: fix STMicroelectronics copyright
Uniformize STMicroelectronics copyrights headers for STV0991
related code.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-11-06 09:51:01 -05:00
Patrice Chotard
3bc599c956 stm32: fix STMicroelectronics copyright
Uniformize STMicroelectronics copyrights headers for STM32
related code.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-11-06 09:51:01 -05:00
Patrice Chotard
fb48bc448c sti: fix STMicroelectronics copyright
Uniformize all STMicroelectronics copyrights headers for STi
related code.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-11-06 09:51:01 -05:00
Fabio Estevam
e1f0715f64 wandboard: Add support for the MX6QP variant
Add support for the latest MX6QP wandboard variant.

Based on Richard Hu's work from Technexion's U-Boot tree.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-10-31 11:01:38 +01:00
Tom Rini
2d5e6b4aac Merge git://git.denx.de/u-boot-video 2017-10-29 10:11:08 -04:00
Tom Rini
bb3d9ed3a9 Merge git://git.denx.de/u-boot-fsl-qoriq 2017-10-27 21:59:10 -04:00
Sumit Garg
9b3f40ad09 armv8: sec_firmware: Add support for loadables in FIT
Enable support for loadables in SEC firmware FIT image. Currently
support is added for single loadable image.

Brief description of implementation:
  Add two more address pointers (loadable_h, loadable_l) as arguments to
  sec_firmware_init() api.
  Create new api: sec_firmware_checks_copy_loadable() to check if loadables
  node is present in SEC firmware FIT image. If present, verify loadable
  image and copies it to secure DDR memory.
  Populate address pointers with secure DDR memory addresses where loadable
  is copied.

Example use-case could be trusted OS (tee.bin) as loadables node in SEC
firmware FIT image.

Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-10-27 08:47:14 -07:00
Sumit Garg
9781d9ff5f armv8: layerscape: Allocate 66 MB DDR for secure memory
Change DDR allocated for secure memory from 2 MB to 66 MB. This
additional 64 MB secure memory is required for trusted OS running
in Trusted Execution Environment using ARMv8 TrustZone.

Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-10-27 08:47:14 -07:00
Vasily Khoruzhick
79f285ddeb sunxi: video: split out PLL configuration code
It will be reused in new DM LCD driver.

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
2017-10-27 09:39:19 +02:00
Quentin Schulz
c96f598be7 sunxi: clk: fix N formula for CPUX clocks
As explained in arch/arm/mach-sunxi/clock_sun8i_a83t.c, clk for CPU
clusters is computed as clk = 24*n. However, the current formula is clk
= 24*(n-1).

This results in a clock set to a frequency that isn't specified as
possible for CPUs.

Let's use the correct formula.

Fixes: f542948b1e ("sunxi: clk: add basic clocks for A83T")

Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-10-25 10:05:05 +02:00
Tom Rini
26f9184e09 Merge git://git.denx.de/u-boot-fsl-qoriq 2017-10-12 13:36:58 -04:00
Diego Dorta
e2000731ae mx6: sys_proto: Add prototypes for imx6_pcie_toggle() functions
When compiling with W=1 errors are observed:

drivers/pci/pcie_imx.c:517:12: warning: no previous prototype for ‘imx6_pcie_toggle_power’ [-Wmissing-prototypes] __weak int imx6_pcie_toggle_power(void)

drivers/pci/pcie_imx.c:528:12: warning: no previous prototype for ‘imx6_pcie_toggle_reset’ [-Wmissing-prototypes] __weak int imx6_pcie_toggle_reset(void)

Remove these warnings by adding the functions prototypes on arch-mx6/sys_proto.

Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
2017-10-12 18:00:18 +02:00
Diego Dorta
342b4b09b1 mx6: clock: Add a prototype for do_mx6_showclocks()
When compiling with W=1 the following warning is observed:

arch/arm/mach-imx/mx6/clock.c:1268:5: warning: no previous prototype for ‘do_mx6_showclocks’ [-Wmissing-prototypes] int do_mx6_showclocks(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])

Remove this warning by adding the function prototype into arch-mx6/clock.h file.

Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
2017-10-12 18:00:01 +02:00
Uri Mashiach
c5c6f37a04 imx: mx7: SPL support for i.MX7
Add configuration file and spl_boot_device function for the i.MX7 SPL.

Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
2017-10-12 17:31:16 +02:00
Uri Mashiach
258bad41ac imx: mx7: DDR controller configuration for the i.MX7 architecture
The configuration files imximage.cfg are used for the DDR controller
configuration.
Add DDR configuration function to replace the DDR controller
configuration in the imximage.cfg file. The function can be used for
DDR size detection.

Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
2017-10-12 17:31:16 +02:00
Uri Mashiach
8bf2d77806 imx: mx7: fix the CCM_ macros
The CCM_ macros use the CCM_BASE_ADDRESS macro, which doesn't exist.
Replace the CCM_BASE_ADDRESS macros with CCM_BASE_ADDR.

Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2017-10-12 17:31:16 +02:00
Diego Dorta
9f272573b7 imx: sys_proto: Add a prototype for board_mmc_get_env_dev()
When compiling with W=1 the following warning is observed:

board/freescale/mx6sabresd/mx6sabresd.c:266:5: warning:
no previous prototype for ‘board_mmc_get_env_dev’
[-Wmissing-prototypes] int board_mmc_get_env_dev(int devno)

Remove this warning by adding the function prototype into sys_proto.h file.

Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-10-12 17:31:16 +02:00
York Sun
fb97b8621e armv8: layerscape: Enable falcon boot
Add jump_to_image_linux() for arm64. Add "noreturn" flag to
armv8_switch_to_el2(). Add hooks to fsl-layerscape to enable falcon
boot.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Tested-by: Łukasz Majewski <lukma@denx.de>
2017-10-09 08:48:45 -07:00
zijun_hu
34f9a92583 ARMv8: make master CPU checking logic more clear
macro branch_if_master checks master CPU via (Aff3 & (Aff2:Aff1:Aff0))
it is simple but a little obscure.

fix by checking Affx fields within MPIDR_EL1 directly.

Signed-off-by: zijun_hu <zijun_hu@htc.com>
2017-10-08 16:19:56 -04:00
Maxime Ripard
8829076a5b arm: sunxi: Move spl_boot_device in a separate function
U-Boot itself might need to identify the boot device, for example to be
able to tell where to load the kernel from when several options are
possible.

Move the logic of spl_boot_device to a function that is compiled both for
the SPL and the main binary.

Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:06 +02:00
Maxime Ripard
3a61b080ac musb: sunxi: switch to the device model
The device model was implemented so far using a hook that needed to be
called from the board support, without DT support and only for the host.

Switch to probing both in peripheral and host mode through the DT.

Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:05 +02:00
Paul Burton
8f8e6304df arm: Use asm-generic/io.h
Convert the arm architecture to make use of the new asm-generic/io.h to
provide address mapping functions. As the generic implementations are
suitable for arm this is primarily a matter of removing code.

This has only been build-tested, feedback from architecture maintainers
is welcome.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-02 21:52:20 -04:00
Philipp Tomsich
3b4f87735d rockchip: bootrom: add definitions to retrieve BROM boot-source
The Rockchip BROM allows reading where it booted from from SRAM.
This adds the necessary definitions (as received from Kever) for
the location of this information in the RK3399's SRAM and naming
for the constants used.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-01 00:33:34 +02:00
Jagan Teki
a982d5156d armv7: rk3288: Move configure_l2ctlr to common
configure_l2ctlr will be shared between SPL and TPL so
move them into asm/arch/sys_proto.h

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:33 +02:00
Jagan Teki
d9a7dcf5b8 armv7: Move L2CTLR read/write to common
L2CTLR read/write functions are common to armv7 so, move
them in to include/asm/armv7.h and use them where ever it need.

Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Backed out the change to arch/arm/mach-tegra/cache.c:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:33 +02:00
Kever Yang
04e97e48d0 rockchip: rk3036: fix grf macro define
Some of macros definition are not correct, fix them according to TRM.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:32 +02:00
Kever Yang
0176399b79 rockchip: rk322x: add sdram driver
Add driver for rk322x to support sdram initialize in SPL.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:32 +02:00
David Wu
615514c16d rockchip: clk: Add rk3368 SARADC clock support
The clk_saradc is dividing from the 24M, clk_saradc=24MHz/(saradc_div_con+1).
SARADC integer divider control register is 8-bits width.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:30 +02:00
David Wu
2e4ce50d1a rockchip: clk: Add rv1108 SARADC clock support
The clk_saradc is dividing from the 24M, clk_saradc=24MHz/(saradc_div_con+1).
SARADC integer divider control register is 10-bits width.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01 00:33:29 +02:00
Sriram Dash
e45ff0ce63 armv8: fsl: ifc: Put IFC related code under CONFIG_FSL_IFC
IFC code is put under CONFIG_FSL_IFC

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-22 12:45:17 -07:00
Patrice Chotard
246771b184 board: Add stm32h7 SoC, discovery and evaluation boards support
This patch adds support for stm32h7 soc family, stm32h743
discovery and evaluation boards.

For more information about STM32H7 series, please visit:
http://www.st.com/en/microcontrollers/stm32h7-series.html

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-22 07:40:03 -04:00
Patrice Chotard
40d1a31e63 usb: dwc3: Add dwc3 glue driver support for STi
This patch adds the ST glue logic to manage the DWC3 HC
on STiH407 SoC family. It configures the internal glue
logic and syscfg registers.

Part of this code been extracted from kernel.org driver
(drivers/usb/dwc3/dwc3-st.c)

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-22 07:39:59 -04:00
Tom Rini
e884656c2c Merge git://www.denx.de/git/u-boot-imx 2017-09-20 12:32:34 -04:00
David Wu
4c94aacd62 rockchip: rk322x: Disable integrated macphy for saving power consuming
Unfortunately, the integrated macphy default is enabled, which will
increase power consuming, if we do not use this PHY. So let's disable
it at first, which will save power consuming. If we really use it, then
enable it in driver level.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18 20:40:33 +02:00
Eric Nelson
8590786acf imx: imx7d: remove CamelCase from ENET_xMHz macros
Update these macros to use all upper-case to avoid checkpatch
warnings:

	ENET_25MHz,
	ENET_50MHz,
	ENET_125MHz,

Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-09-18 17:15:28 +02:00
Stefan Agner
7d289d6239 imx: add macro to detect whether USB PHY is active
This macro allows to detect whether the USB PHY is active. This
is helpful to detect if the boot ROM has previously started the
USB serial downloader.

The idea is taken from the mfgtool support in the NXP U-Boot:
http://git.freescale.com/git/cgit.cgi/imx/uboot-imx.git/commit/?h=imx_v2016.03_4.1.15_2.0.0_ga&id=a352ed3c5184b95c4c9f7468f5fbb5f43de5e412

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
2017-09-18 16:51:36 +02:00
Suman Anna
2f9455c849 ARM: DRA7: Cleanup old pinctrl macros
Commit 6ae4c3efbd ("ARM: DRA7: Add pinctrl register definitions")
has added new macros for pinmux configuration in line with the kernel
definitions. Cleanup the old pinctrl macros from the common header
file so that they are not used by any new boards.

Signed-off-by: Suman Anna <s-anna@ti.com>
2017-09-14 21:32:56 -04:00
Vishal Mahaveer
ba39608147 ARM: DRA72x: Add support for detection of DRA71x SR 2.1
DRA71x processors are reduced pin and software compatible
derivative of DRA72 processors. Add support for detection
of SR2.1 version of DRA71x family of processors.

Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-12 18:02:29 -04:00
Masahiro Yamada
b27af39935 dma: import linux/dma-direction.h to consolidate enum dma_data_direction
Import include/linux/dma-direction.h from Linux 4.13-rc7 and delete
duplicated definitions of enum dma_data_direction.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2017-09-12 18:02:23 -04:00
Andy Yan
347e30e172 armv8: mmu: add space around operator
Add space around operator "+", make it
match the coding style.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-12 18:00:09 -04:00
Andy Yan
4f84cb980f armv8: mmu: remove unused macro definition
Macro VA_BITS and PTE_BLOCK_BITS are not used
in the code, so remove them.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-12 18:00:08 -04:00
Tom Rini
8a33cb8b6b Merge git://git.denx.de/u-boot-fsl-qoriq 2017-09-12 12:02:50 -04:00
Steve Kipisz
209742fa88 board: ti: am571x: Add 666MHz support for AM571x IDK
AM571x supports DDR running at 666MHz. Right now it is
clocked at 532MHz which is lower than what is supported.
In order to have maximum performance on AM571-IDK,
switch DDR to 666MHz.

Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-09-11 16:22:31 -04:00
Keerthy
c247605510 board: ti: dra76-evm: Add the pmic data
dra76-evm uses lp8736 and tps65917 pmic for powering on
various peripherals. Add data for these pmics and register
for dra76-evm.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11 16:19:40 -04:00
Praneeth Bajjuri
0f9e6aee9d arm: dra76: Add support for ES1.0 detection
dra76 family is a high-performance, infotainment application
device, based on OMAP architecture on a 28-nm technology.
This contains most of the subsystems, peripherals that are
available on dra74, dra72 family. This SoC mainly features
Subsystems:
- 2 x Cortex-A15 with max speed of 1.8GHz
- 2 X DSP
- 2 X Cortex-M4 IPU
- ISS
- CAL
- DSS
- VPE
- VIP
Connectivity peripherals:
- 1 USB3.0 and 3 USB2.0 subsystems
- 1 x SATA
- 2 x PCI Express Gen2
- 3-port Gigabit ethernet switch
- 2 x CAN
- MCAN

Adding CPU detection support for the dra76 ES1.0 soc
and update prcm, control module, dplls data.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11 16:19:38 -04:00
Lokesh Vutla
91d3e90668 arm: omap5+: Add board specific ldo powering
It is not necessary all omap5+ based uses the same PMIC
to poweron mmc. So add support for enabling mmc based on board.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11 16:19:35 -04:00
Hou Zhiqiang
c4787f4b23 armv8: ls1088a: fix the MMU table for pcie config space
The pcie config space of ls1088a is different from ls2080a.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:01:07 -07:00
Ran Wang
0e8a4264ec armv7: Add workaround for USB erratum A-009007
Rx Compliance tests may fail intermittently at high
jitter frequencies using default register values

Program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.bhagat@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:01:07 -07:00
Ran Wang
e10d114279 armv7: Add workaround for USB erratum A-008997
Low Frequency Periodic Singaling (LFPS) Peak-to-Peak Differential
Output Voltage Test Compliance fails using default transmitter settings

Change config of transmitter signal swings by setting register
PCSTXSWINGFULL to 0x47 to pass compliance tests.

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:01:06 -07:00
Ran Wang
c1853f6f73 armv7: Add workaround for USB erratum A-009798
The default setting for USB High Speed Squelch Threshold results
in a threshold close to or lower than 100mV. This leads to Receive
Compliance test failure for a 100mV threshold.

Shift the threshold from ~100mV towards ~130mV by setting SQRXTUNE
to 0x0 to pass USB High Speed Receiver Sensitivity Compliance test.

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:01:06 -07:00
Ran Wang
83fa71189a armv7: Add workaround for USB erratum A-009008
USB High Speed (HS) EYE Height Adjustment
USB HS speed eye diagram fails with the default value at
many corners, particularly at a high temperature

Optimal eye at TXREFTUNE value to 0x9 is observed, change
set the same value.

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:01:06 -07:00
Ran Wang
15d59b5316 armv8: Add workaround for USB erratum A-009007
Rx Compliance tests may fail intermittently at high
jitter frequencies using default register values.

Program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.bhagat@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:01:06 -07:00
Ran Wang
9d1cd910f7 armv8: Add workaround for USB erratum A-008997
Low Frequency Periodic Signaling(LFPS) Peak-to-Peak Differential
Output Voltage Test Compliance fails using default transmitter
settings

Change config of transmitter signal swings by setting register
PCSTXSWINGFULL to 0x47 to pass compliance tests.

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:01:06 -07:00
Ran Wang
2a8a353958 armv8: Add workaround for USB erratum A-009798
The default setting for USB High Speed Squelch Threshold results
in a threshold close to or lower than 100mV. This leads to Receiver
Compliance test failure for a 100mV threshold.

Shift the threshold from ~100mV towards ~130mV by setting SQRXTUNE
to 0x0 to pass USB High Speed Receiver Sensitivity Compliance test.

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:01:06 -07:00
Ran Wang
2ab1553f08 armv8: Add workaround for USB erratum A-009008
USB High Speed (HS) EYE Height Adjustment
USB HS speed eye diagram fails with the default value at
many corners, particularly at a high temperature

Optimal eye at TXREFTUNE value to 0x9 is observed, change
set the same value.

Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:01:06 -07:00
Ran Wang
9a609a8800 armv8: Add scfg_clrsetbits_32(), scfg_clrbits_32()
Some erratum patch might need it to program registers.

Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:01:05 -07:00
Ashish Kumar
17d066fc5d armv8: fsl-layerscape: Support to add RGMII for ls1088aqds
This patch adds support for RGMII protocol

NXP's LDPAA2 support RGMII protocol. LS1088A is the
first Soc supporting both RGMII and SGMII.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:01:05 -07:00
Ashish Kumar
6d9b82d085 armv8: ls1088a: Add NXP LS1088A SoC support
LS1088A is compliant with the Layerscape Chassis Generation 3 with
eight ARM v8 Cortex-A53 cores in 2 cluster, CCI-400, one 64-bit DDR4
SDRAM memory controller with ECC, Data path acceleration architecture
2.0 (DPAA2), Ethernet interfaces (SGMIIs, RGMIIs, QSGMIIs, XFIs),
QSPI, IFC, PCIe, SATA, USB, SDXC, DUARTs etc.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
[YS: Revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:00:13 -07:00
Suresh Gupta
22c51855bf armv8: fsl-layerscape: Fix final MMU table for QSPI and IFC
For QSPI and IFC addresses execution shouldn't be allowed
when u-boot running from DDR. Revise the MMU final table
to enforce execute-never bits.

Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:00:13 -07:00
Udit Agarwal
15e7c681e1 LS2080ARDB: QSPI boot: Secure Boot image validation
Adds header address for PPA to be validated during ESBC phase for
ARCH_LS2088 and QSPI_BOOT. Moves sec_init prior to ppa_init(). It
must be initialized before the PPA.

Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[YS: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 07:55:36 -07:00
Sumit Garg
06fb06f66c SECURE_BOOT: Unify memory map for Layerscape based platforms
Unify memory map for Layerscape based platforms. This patch includes
changes in bootscript, bootscript header and PPA header addresses
change as per unified memory map.

Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Tested-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 07:55:36 -07:00
Ashish Kumar
63b2316c5c fsl-layerscape: Consolidate registers space defination for CCI-400 bus
CoreLink Cache Coherent Interconnect (CCI) provides full cache
coherency between two clusters of multi-core CPUs and I/O coherency
for devices and I/O masters.

This patch add new config option SYS_FSL_HAS_CCI400 and moves
existing register space definaton of CCI-400 bus to fsl_immap to be
shared. CONFIG_SYS_CCI400_ADDR is replaced with SYS_CCI400_OFFSET
in Kconfig.

Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[YS: revised commit message, squashed patches for armv8 and armv7]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 07:55:36 -07:00
Wadim Egorov
40d4f79b81 rockchip: rk3288: Add reset reason detection
Sometimes it's helpful to know the reset reason caused in the SoC.
Add reset reason detection for the RK3288 SoC.
This will set an environment variable which represents the reset reason.

Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-05 11:04:35 +02:00
Adam Ford
fc760cc6e8 Convert CONFIG_SYS_I2C_BUS_MAX to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_I2C_BUS_MAX

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Fix AM43XX drop AM44XX]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-09-01 20:44:30 -04:00
Adam Ford
ac1d8ac871 Configs: Migrate I2C_BUS_MAX to CONFIG_SYS_I2C_BUS_MAX
For consistency with other platforms and in preparation of Kconfig
migration, let's change Several TI platforms that use I2C_BUS_MAX
to CONFIG_SYS_I2C_BUS_MAX

Signed-off-by: Adam Ford <aford173@gmail.com>
2017-09-01 17:56:20 -04:00
Tom Rini
0b6e5b2c48 Merge git://git.denx.de/u-boot-sunxi 2017-09-01 13:30:19 -04:00
Dave Prue
6ff005cf19 sunxi: Fix CONFIG_SUNXI_GMAC references
SUNXI_GMAC was still used to configure the code where as the
same has been renamed and moved to Kconfig in below commit
"sunxi: Move SUNXI_GMAC to Kconfig"
(sha1: 4d43d065db)

Signed-off-by: Dave Prue <dave@prue.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
[Tweek commit message, config_whitelist.txt, build-whitelist.sh]
Signed-off-by: Jagan Teki <jagan@openedev.com>
2017-09-01 20:48:27 +05:30
Tom Rini
6aee2ab68c Merge git://git.denx.de/u-boot-imx
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	configs/imx6qdl_icore_mmc_defconfig
	configs/imx6qdl_icore_rqs_defconfig
2017-09-01 10:40:59 -04:00
Maxime Ripard
de9b1771c3 mmc: sunxi: Support new mode
Almost all of the newer Allwinner SoCs have a new operating mode for the
eMMC clocks that needs to be enabled in both the clock and the MMC
controller.

Details about that mode are sparse, and the name itself (new mode vs old
mode) doesn't give much details, but it seems that the it changes the
sampling of the MMC clock. One side effect is also that it divides the
parent clock rate by 2.

Add support for it through a Kconfig option.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-08-28 22:36:44 +05:30
Breno Lima
3aa4b703b4 imx: imx6: Move gpr_init() function to soc.c
Since the gpr_init() function is common for boards using MX6S, MX6DL, MX6D,
MX6Q and MX6QP processors move it to the soc.c file.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-08-28 09:48:53 +02:00
Ruchika Gupta
a797f274d7 ARMv8/sec_firmware : Update chosen/kaslr-seed with random number
kASLR support in kernel requires a random number to be passed via
chosen/kaslr-seed propert. sec_firmware generates this random seed
which can then be passed in the device tree node.

sec_firmware reserves JR3 for it's own usage. Node for JR3 is
removed from device-tree.

Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
2017-08-26 14:56:11 -04:00
Stefan Agner
3bd1642d4d imx: fix USB boot mode detection for i.MX 6UL and 6ULL
Add the reserved boot mode used in the bmode command for i.MX 6UL
and 6ULL as introduced in commit 3fd9579085 ("imx: mx6ull: fix USB
bmode for i.MX 6UL and 6ULL").

Also replace BMODE_UART with BMODE_RESERVED, which is more appropriate.
Commit 96aac843b6 ("imx: Use IMX6_BMODE_* macros instead of numericals")
added macros for boot modes, in the process the reserved boot mode got
named BMODE_UART. We use the reserved boot mode in the bmode command to
let the boot ROM enter serial downloader recovery mode. But this is only
a side effect, the actual boot mode is reserved...

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2017-08-25 13:31:31 +02:00
Stefano Babic
7c09cbf68b imx: fix licensing in i.MX files
Some files for i.MX do not yet have the SPDX ID to reference the correct
license.

Signed-off-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Wolfgang Denk <wd@denx.de>
2017-08-23 10:45:45 +02:00
Kever Yang
a80b3b0378 rockchip: rk322x: update MACRO for mmc clksel reg
The description for eMMC/SDIO/SDMMC src is not correct,
update the CRU_CLKSEL11_CON value definition according to TRM.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-18 17:52:47 +02:00
Tom Rini
ceff355a5f Merge git://git.denx.de/u-boot-sunxi
Update A20-OLinuXino-Lime2-eMMC_defconfig to include CONFIG_SCSI

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-16 18:12:40 -04:00
Tom Rini
470135be27 Merge git://www.denx.de/git/u-boot-imx
Update pfla02 for setenv changes and PHYLIB/etc migration to Kconfig.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-16 18:12:00 -04:00
Anatolij Gustschin
557b9b7250 imx6: use SION macro in SDn_CMD mux mode bitfield arguments
Select SION by appropriate macro instead of constant.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-08-16 11:36:05 +02:00
Tom Rini
c1b62ba9ca Merge branch 'master' of git://git.denx.de/u-boot-rockchip 2017-08-14 10:40:01 -04:00
Patrice Chotard
bc5d038445 stm32f1: remove stm32f1 support
A few years ago STM32F1 SoCs support has been added :
0144caf22c  gpio: stm32: add stm32f1 support
2d18ef2364  ARMv7M: add STM32F1 support

But neither STM32F1 dedicated defconfig nor board was
associated to these commits.

Got confirmation from Tom Rini and Matt Porter to remove
all this code [1]

[1] http://u-boot.10912.n7.nabble.com/Remove-STM32F1-support-td301603.html

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-08-13 15:17:37 -04:00
Nishanth Menon
0459bc30b6 ARM: OMAP5: Enable support for AVS0 for OMAP5 production devices
OMAP5432 did go into production with AVS class0 registers which were
mutually exclusive from AVS Class 1.5 registers.

Most OMAP5-uEVM boards use the pre-production Class1.5 which has
production efuse registers set to 0. However on production devices,
these are set to valid data.

scale_vcore logic is already smart enough to detect this and use the
"Nominal voltage" on devices that do not have efuse registers populated.

On a test production device populated as follows:
MPU OPP_NOM:
=> md.l 0x04A0021C4 1
4a0021c4: 03a003e9                               ....
(0x3e9 = 1.01v) vs nom voltage of 1.06v
MPU OPP_HIGH:
=> md.l 0x04A0021C8 1
4a0021c8: 03400485                               ..@.

MM OPP_NOM:
=> md.l 0x04A0021A4 1
4a0021a4: 038003d4                               ....
(0x3d4 = 980mV) vs nom voltage of 1.025v
MM OPP_OD:
=> md.l 0x04A0021A8 1
4a0021a8: 03600403                               ..`.

CORE OPP_NOM:
=> md.l 0x04A0021D8 1
4a0021d8: 000003cf                               ....
(0x3cf = 975mV) vs nom voltage of 1.040v

Since the efuse values are'nt currently used, we do not regress on
existing pre-production samples (they continue to use nominal voltage).

But on boards that do have production samples populated, we can leverage
the optimal voltages necessary for proper operation.

Tested on:
a) 720-2644-001 OMAP5UEVM with production sample.
b) 750-2628-222(A) UEVM5432G-02 with pre-production sample.

Data based on OMAP5432 Technical reference Manual SWPU282AF (May
2012-Revised Aug 2016)

NOTE: All collaterals on OMAP5432 silicon itself seems to have been
removed from ti.com, though EVM details are still available:
http://www.ti.com/tool/OMAP5432-EVM

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-08-13 15:17:35 -04:00
Nishanth Menon
5796b66651 ARM: OMAP5: Remove OPP_LOW Definitions for ES2.0
ES2.0 descopes OPP_LOW definition. So remove it from macros defined.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-08-13 15:17:35 -04:00
Kever Yang
bf82e200a9 rockchip: rk3288: fix EMMC_DIV_MASK definition in header
It should be '<<' instead of '<' for _MASK definition, fix it.

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-13 17:15:08 +02:00
Philipp Tomsich
403e9cbcd5 rockchip: rk3368: add DRAM controller driver with DRAM initialisation
This adds a DRAM controller driver for the RK3368 and places it in
drivers/ram/rockchip (where the other DM-enabled DRAM controller
drivers for rockchip devices should also be moved eventually).

At this stage, only the following feature-set is supported:
 - DDR3
 - 32-bit configuration (i.e. fully populated)
 - dual-rank (i.e. no auto-detection of ranks)
 - DDR3-1600K speed-bin

This driver expects to run from a TPL stage that will later return to
the RK3368 BROM.  It communicates with later stages through the
os_reg2 in the pmugrf (i.e. using the same mechanism as Rockchip's DDR
init code).

Unlike other DMC drivers for RK32xx and RK33xx parts, the required
timings are calculated within the driver based on a target frequency
and a DDR3 speed-bin (only the DDR3-1600K speed-bin is support at this
time).

The RK3368 also has the DDRC0_CON0 (DDR ch. 0, control-register 0)
register for controlling the operation of its (single-channel) DRAM
controller in the GRF block.  This provides for selecting DDR3, mobile
DDR modes, and control low-power operation.
As part of this change, DDRC0_CON0 is also added to the GRF structure
definition (at offset 0x600).

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-13 17:12:33 +02:00
Philipp Tomsich
793f2fd2dc net: gmac_rockchip: Add support for the RK3368 GMAC
The GMAC in the RK3368 once again is identical to the incarnation in
the RK3288 and the RK3399, except for where some of the configuration
and control registers are located in the GRF.

This adds the RK3368-specific logic necessary to reuse this driver.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-08-13 17:12:33 +02:00
Philipp Tomsich
df0ae00041 rockchip: clk: rk3368: add support for GMAC (SLCK_MAC) clock
To enable the GMAC on the RK3368, we need to set up the clocking
appropriately to generate a tx_clk for the MAC.

This adds an implementation that implements the use of the <&ext_gmac>
clock (i.e. an external 125MHz clock for RGMII provided by the PHY).
This is the clock setup used by the boards currently supported by
U-Boot (i.e. Geekbox, Sheep and RK3368-uQ7).

This includes the change from commit
 - rockchip: clk: rk3368: define GMAC_MUX_SEL_EXTCLK

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-13 17:12:32 +02:00
Philipp Tomsich
f5a432959a rockchip: clk: rk3368: implement MMC/SD clock reparenting
The original clock support for MMC/SD cards on the RK3368 suffered
from a tendency to select a divider less-or-equal to the the one
giving the requested clock-rate: this can lead to higher-than-expected
(or rather: higher than supported) clock rates for the MMC/SD
communiction.

This change rewrites the MMC/SD clock generation to:
 * always generate a clock less-than-or-equal to the requested clock
 * support reparenting among the CPLL, GPLL and OSC24M parents to
   generate the highest clock that does not exceed the requested rate

In addition to this, the Linux DTS uses HCLK_MMC/HCLK_SDMMC instead of
SCLK_MMC/SCLK_SDMMC: to match this (and to ensure that clock setup
always works), we adjust the driver appropriately.

This includes the changes from:
 - rockchip: clk: rk3368: convert MMC_PLL_SEL_* definitions to shifted-value form

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-13 17:12:32 +02:00
Philipp Tomsich
05c57e12d1 rockchip: clk: rk3368: define DMA1_SRST_REQ and DMA2_SRST_REQ
On he RK3368, we need to temporarily disable security on the DMA
engines during TPL and SPL to allow the MMC host to DMA into DRAM.  To
do so, we need to reset the two DMA engines, which in turn requires
the DMA1_SRST_REQ and DMA2_SRST_REQ constants to refer to the
appropriate bits in the CRU.

As the ATF correctly initialises security (and only leaves EL3 after
doing so), this can not pose a security issue.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-13 17:12:32 +02:00
Philipp Tomsich
a49773d6cf rockchip: pinctrl: rk3368: move IOMUX bit-definitions to pinctrl driver
There is no real reason to keep the bit-definitions for the IOMUX in
the grf header file (which defines the register layout of the GRF block):
these should only be used by our pinctrl driver (with the possible
exception of early debug-init code in TPL/SPL).

This moves the relevant definitions from the grf_rk3368.h header
into the pinctrl driver pinctrl_rk3368.c.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-13 17:12:24 +02:00
Philipp Tomsich
c1828cf7ab rockchip: rk3368: grf: use shifted-constants
The RK3368 GRF header was still defines with a shifted-mask but with
non-shifted function selectors for the IOMUX defines.  As the RK3368
support is still fresh enough to allow a quick change, we do this now
before having more code use this.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-13 17:12:23 +02:00
Philipp Tomsich
525a8c8f2c rockchip: rk3368: pmugrf: add definitions for os_reg[0..3]
On the RK3368 we use a TPL-stage similar to Rockchip's DDR init
(i.e. it initialises DRAM, leaves some info for the next stage and
returns to the BootROM).  To allow compatibility with Rockchip's DDR
init code, we use the same register os_reg2 in pmugrf for passing
this info (i.e. DRAM size and configuration) between stages.

This change adds the definitions for os_reg[0] through os_reg[3] to
the pmugrf structure for the RK3368.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-13 17:12:22 +02:00
Philipp Tomsich
225d30b708 spl: add a 'return to bootrom' boot method
Some devices (e.g. the RK3368) have only limited SRAM, but provide
support for loading the next boot stage after our SPL performs basic
setup (e.g. DRAM).

For target systems like these, we add a boot device BOOTROM that will
invoke a board-specific hook to return to the bootrom (if supported).

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-13 17:12:19 +02:00
Tom Rini
7f513e8196 Merge git://git.denx.de/u-boot-fsl-qoriq 2017-08-11 07:10:18 -04:00
Icenowy Zheng
39858b12cc sunxi: add PRCM secure switch register definition
Some new Allwinner SoCs' PRCM has a secure switch register, which
controls the access to some clock and power registers in PRCM block.

Add the definition of this register and its bits in the PRCM header
file.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-08-11 15:49:39 +05:30
Rajesh Bhagat
a8ecb39e9e config: ls1012aqds: Enable USB EHCI support for ls1012aqds
Signed-off-by: Rajat Srivastava <rajat.srivastava@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: yinbo.zhu <yinbo.zhu@nxp.com>
[YS: Revise subject, remove commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-08-09 09:57:32 -07:00
Suji Velupillai
c89782dcac net: move Broadcom SF2 driver to Kconfig
move to Kconfig:
	CONFIG_BCM_SF2_ETH
	CONFIG_BCM_SF2_ETH_DEFAULT_PORT
	CONFIG_BCM_SF2_ETH_GMAC

Also modified defconfigs of all platforms that use these configs.

Signed-off-by: Suji Velupillai <suji.velupillai@broadcom.com>
Tested-by: Suji Velupillai <suji.velupillai@broadcom.com>
Reviewed-by: JD Zheng <jiandong.zheng@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Steve Rae <steve.rae@raedomain.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-08-07 15:18:30 -05:00
Tom Rini
fe84c48eeb Xilinx changes for v2017.09
Zynq:
 - Add Z-Turn board support
 
 fpga:
 - Remove intermediate buffer from code
 
 Zynqmp:
 - dts cleanup
 - change psu_init handling
 - Add options to get silicon version
 - Fix time handling
 - Map OCM/TCM via MMU
 - Add new clock driver
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iEYEABECAAYFAlmBs2kACgkQykllyylKDCFUGgCgmfop8Ki5+6QI7XQRP7u8nhjw
 KakAn1sYIRDFQ34AoxmiYa6RTmjepLMv
 =1Gh3
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2017.09' of git://www.denx.de/git/u-boot-microblaze

Xilinx changes for v2017.09

Zynq:
- Add Z-Turn board support

fpga:
- Remove intermediate buffer from code

Zynqmp:
- dts cleanup
- change psu_init handling
- Add options to get silicon version
- Fix time handling
- Map OCM/TCM via MMU
- Add new clock driver
2017-08-04 07:23:32 -04:00
Tom Rini
ec7483e34e Merge git://git.denx.de/u-boot-fsl-qoriq
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	include/configs/ls1046aqds.h
	include/configs/ls1046ardb.h
2017-08-02 10:52:26 -04:00
Siva Durga Prasad Paladugu
74ba69db35 arm64: zynqmp: Make chip_id routine to handle based on el.
Modify chip_id() routine such that to handle based on
the current el. Also make it available even if FPGA is
not enabled in system such it can be used always.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-08-02 09:11:52 +02:00
Siva Durga Prasad Paladugu
f52bf5a3dd arm64: zynqmp: Make chip_id a global routine()
This patch makes chip_id() as a global routine so that
it can be used in other places as required.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-08-02 09:11:52 +02:00
Siva Durga Prasad Paladugu
db3123b40d arm64: zynqmp: Modify chip_id routine to get either idcode or version
This patch modifies the chip_id routine to get either idcode or
silicon version based on the argument received.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-08-02 09:11:52 +02:00
Siva Durga Prasad Paladugu
4b5b0fcd21 arm64: zynqmp: Dont write to system timestamp generator
Remove incorrect code of writing to system timestamp
counter registers. This register writes does nothing
and can be removed.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-08-02 09:11:52 +02:00
Siva Durga Prasad Paladugu
a076789efe arm64: zynqmp: Define a way to intialize TCM
TCM on ZynqMP needs to be intialized in a sequence
and this patch provides a global routine to perform
this as per requirement.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-08-02 09:11:52 +02:00
Santan Kumar
ec8a7d7743 soc/fsl-layerscape: Update SVR number for LS2081A and LS2041A
Update SVR as per the SOC document.
 -LS2081A: 0x870919 -> 0x870918
 -LS2041A: 0x870915 -> 0x870914

Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-08-01 08:28:56 -07:00
Alison Wang
020b3ce8ae armv8: Remove duplicate definition for IH_ARCH_ARM and IH_ARCH_ARM64
The duplicate definitions for IH_ARCH_ARM and IH_ARCH_ARM64 are removed.
The definitions in <image.h> are used.

According to this modification, the comparison between os arch and cpu
arch is done in C programming instead of ASM programming.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-08-01 08:28:56 -07:00
Tom Rini
211aaf309c Merge git://git.denx.de/u-boot-usb 2017-07-29 11:43:51 -04:00
Bin Meng
cbb89ed026 configs: Remove CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS in all boards
Now that EHCD does not use CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS,
remove it in all boards' config files.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
2017-07-28 23:34:24 +02:00
Simon Glass
000f15fa15 dm: tegra: Convert clock_decode_periph_id() to support livetree
Adjust this to take a device as a parameter instead of a node.

Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Tested-by: Stephen Warren <swarren@nvidia.com>
2017-07-28 12:02:47 -06:00
Simon Glass
be7890927a dm: tegra: Convert USB setup to livetree
Adjust this code to support a live device tree. This should be implemented
as a PHY driver but that is left as an exercise for the maintainer.

Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
2017-07-28 12:02:47 -06:00
Simon Glass
66de3eee79 tegra: tegra124: Add a PMC syscon driver
The PMC can be modelled as a syscon peripheral. Add a driver for this
so that it can be accessed by drivers when needed. Enable it for tegra124
boards.

Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Tested-by: Stephen Warren <swarren@nvidia.com>
2017-07-28 12:02:47 -06:00
Philipp Tomsich
01106571ad rockchip: clk: rk3399: remove unused fields from priv-structures
This removes the unused 'rate' field from both rk3399_pmuclk_priv and
rk3399_clk_priv. I didn't bother to check where this came from (i.e.
what the historical context of these was), but only verified that
these are indeed unused across all code-paths.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-07-27 14:59:02 +02:00
Philipp Tomsich
80c83e8190 rockchip: clk: rk3368: remove unused fields from rk3368_clk_priv
The rk3368_clk_priv has two unused fields: rate, has_bwadj. This
removes them as there's no need for either (i.e. has_bwadj is always
true for the RK3368, according to its TRM).

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-07-27 14:59:02 +02:00
Philipp Tomsich
700f3108d3 rockchip: spl: make boot0 hook TPL safe
When building for a TPL/SPL setup (e.g. on the RK3368), we need the
TPL stage to have the extra space for for the 'Rockchip SPL name'
(i.e. 'RK33' word).  Yet, the SPL will start execution at its first
word (i.e. the first word in the SPL binary needs to be a valid
instruction).  To make things a bit more involved, CONFIG_SPL_BUILD
is defined both for the SPL and the TPL stage.

To avoid having to explicitly test for the first stage (TPL, if and
only if TPL and SPL are built, SPL otherwise), this commit modifies
the sequence to repeat the 'b reset' (instead of reserving 4 bytes
of undefined space) at the start of the boot0 hook: if overwritten
(and execution starts at the second word), the first instruction is
still a 'b reset'... if not overwritten, we start on a 'b reset' as
well.

This solution wouldn't even require the check whether we are in the
SPL/TPL build (i.e. CONFIG_SPL_BUILD), but we leave this check in for
documentation purposes.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-07-27 14:59:02 +02:00
Kever Yang
06f4e36baf rockchip: pwm: add mask for config setting
Use mask to clear old setting before direct set the new config,
or else there it will mess up the config when it's not the same
with default value.

Fixes: 3851059 rockchip: Setup default PWM flags
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-07-27 14:59:01 +02:00
Philipp Tomsich
cb91173a7f rockchip: timer: make register sizes explicit
We are about to reuse the rockchip timer (header file) for 64bit ARMv8
chips, so it seems a good time to make the register sizes explicit by
changing from 'unsigned int' to 'u32'.

Reorders the header-includes in rk_timer.c to ensure that 'u32' is
definded before it is used by 'asm/arch/timer.h'.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-07-27 14:59:00 +02:00
Patrice Chotard
9242ece12b ram: stm32: migrate fmc defines in driver file
Migrate all FMC defines from arch/arm/include/asm/arch-stm32f7/fmc.h
to drivers/ram/stm32_sdram.c

This will avoid to add an additionnal arch-stm32xx/fmc.h file when
a new stm32 family soc will be introduced.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-07-26 11:29:07 -04:00
Patrice Chotard
81d0128d2b clk: stm32f7: remove clock_get()
All drivers which was using clock_get() are now using
clk_get_rate() from clock framework, now it's safe to
remove clock_get().

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Vikas MANOCHA <vikas.manocha@st.com>
2017-07-26 11:28:08 -04:00
Patrice Chotard
b9e86511d1 clk: stm32f7: cleanup clocks unused definitions
clean the code by removing unused enums, structs and
defines related to clocks

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Vikas MANOCHA <vikas.manocha@st.com>
2017-07-26 11:26:54 -04:00
Patrice Chotard
288f17e648 clk: stm32f7: add clock .get_rate() callback
Add clock framework .get_rate callback.
This step will allow to convert all drivers which was using
proprietary clock_get() to use clock framework .get_rate().

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Vikas MANOCHA <vikas.manocha@st.com>
2017-07-26 11:26:53 -04:00
Patrice Chotard
704e954cee clk: stm32f7: add static for configure_clocks()
Also remove its declaration from stm32.h which
is no more needed.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Vikas MANOCHA <vikas.manocha@st.com>
2017-07-26 11:26:53 -04:00
Beniamino Galvani
2009a8d03f pinctrl: meson: add GPIO support
This commit adds GPIO support to the Amlogic Meson pin controller
driver, based on code from Linux kernel.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
2017-07-26 11:26:48 -04:00
Andrew F. Davis
03750231a8 arm: mach-omap2: Factor out common FDT fixup suport
Some of the fixups currently done for OMAP5 class boards are common to
other OMAP family devices, move these to fdt-common.c.

Signed-off-by: Andrew F. Davis <afd@ti.com>
2017-07-22 22:22:43 -04:00
Stefano Babic
552a848e4f imx: reorganize IMX code as other SOCs
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.

This change is also coherent with the structure in kernel.

Signed-off-by: Stefano Babic <sbabic@denx.de>

CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Akshay Bhat <akshaybhat@timesys.com>
CC: Ken Lin <Ken.Lin@advantech.com.tw>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Heiko Schocher <hs@denx.de>
CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
CC: Christian Gmeiner <christian.gmeiner@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Patrick Bruenn <p.bruenn@beckhoff.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: "Eric Bénard" <eric@eukrea.com>
CC: Jagan Teki <jagan@amarulasolutions.com>
CC: Ye Li <ye.li@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Adrian Alonso <adrian.alonso@nxp.com>
CC: Alison Wang <b18965@freescale.com>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Martin Donnelly <martin.donnelly@ge.com>
CC: Marcin Niestroj <m.niestroj@grinn-global.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Adam Ford <aford173@gmail.com>
CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
CC: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Soeren Moch <smoch@web.de>
CC: Richard Hu <richard.hu@technexion.com>
CC: Wig Cheng <wig.cheng@technexion.com>
CC: Vanessa Maegima <vanessa.maegima@nxp.com>
CC: Max Krummenacher <max.krummenacher@toradex.com>
CC: Stefan Agner <stefan.agner@toradex.com>
CC: Markus Niebel <Markus.Niebel@tq-group.com>
CC: Breno Lima <breno.lima@nxp.com>
CC: Francesco Montefoschi <francesco.montefoschi@udoo.org>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Scott Wood <oss@buserror.net>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Simon Glass <sjg@chromium.org>
CC: "Andrew F. Davis" <afd@ti.com>
CC: "Łukasz Majewski" <l.majewski@samsung.com>
CC: Patrice Chotard <patrice.chotard@st.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stephen Warren <swarren@nvidia.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: "Álvaro Fernández Rojas" <noltari@gmail.com>
CC: York Sun <york.sun@nxp.com>
CC: Xiaoliang Yang <xiaoliang.yang@nxp.com>
CC: Chen-Yu Tsai <wens@csie.org>
CC: George McCollister <george.mccollister@gmail.com>
CC: Sven Ebenfeld <sven.ebenfeld@gmail.com>
CC: Filip Brozovic <fbrozovic@gmail.com>
CC: Petr Kulhavy <brain@jikos.cz>
CC: Eric Nelson <eric@nelint.com>
CC: Bai Ping <ping.bai@nxp.com>
CC: Anson Huang <Anson.Huang@nxp.com>
CC: Sanchayan Maity <maitysanchayan@gmail.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Patrick Delaunay <patrick.delaunay@st.com>
CC: Gary Bisson <gary.bisson@boundarydevices.com>
CC: Alexander Graf <agraf@suse.de>
CC: u-boot@lists.denx.de
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2017-07-12 10:17:44 +02:00
Tom Rini
8d3a25685e Merge git://git.denx.de/u-boot-dm 2017-07-11 20:28:46 -04:00
Tom Rini
d43ef73bf2 Merge branch 'master' of git://git.denx.de/u-boot-rockchip 2017-07-11 14:21:50 -04:00
Simon Glass
fedb428c5b Convert CONFIG_SCSI to Kconfig
This converts the following to Kconfig:
   CONFIG_SCSI

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-07-11 10:08:19 -06:00
Sjoerd Simons
2454b719fb rockchip: rk3288: Add pinctrl support for the gmac ethernet interface
Add support for the gmac ethernet interface to pinctrl. This hardcodes
the setup to match that of the firefly and Radxa Rock2 boards, using the
RGMII phy mode for gmac interface and GPIO4B0 as the phy reset GPIO.

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-07-11 15:23:38 +02:00
eric.gao@rock-chips.com
e3ef41df48 rockchip: pwm: fix the register layout for the PWM controller
According to rk3288 spec, the pwm register order is:
    PWM_PWM0_CNT,
    PWM_PWM0_PERIOD_HPR,
    PWM_PWM0_DUTY_LPR,
    PWM_PWM0_CTRL
but the source code's order is:
  struct rk3288_pwm {
    u32 cnt;
    u32 duty_lpr;
    u32 period_hpr;
    u32 ctrl;
  };

So, correct it here. It is the same as RK3399.

Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Edited the commit message:
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-07-11 12:13:47 +02:00
Kever Yang
168eef7ada rockchip: rk322x: add basic soc support
Enable soc support for SPL and U-boot skeleton.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-07-11 12:13:46 +02:00
Kever Yang
5cc9d31a79 rockchip: rk322x: add pinctrl driver
Add init pinctrl driver support for:
- i2c;
- spi;
- uart;
- pwm;
- emmc/sdmmc;

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-07-11 12:13:46 +02:00
Kever Yang
045029cbd1 rockchip: rk322x: add clock driver
Add clock driver init support for:
- cpu, bus clock init;
- emmc, sdmmc clock;
- ddr clock;

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Fixed format specified (%x -> %p) in clk_rk322x.c:
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-07-11 12:13:45 +02:00
Kever Yang
cc89369fb0 rockchip: rk3368: add sdram driver for U-Boot
Add sdram driver in U-Boot for get the correct sdram size from
sys_reg, so that U-Boot can co-work with Rockchip loader or SPL
to get different dram capability and then tell the kernel.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-07-11 12:13:45 +02:00
Kever Yang
7805cdf494 rockchip: use common sdram function
Replace the sdram_init() in board init and rockchip_sdram_size() in
sdram driver for all the Rockchip SoCs which enable CONFIG_RAM.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Make dram_init() in rk3036-board.c conditional on CONFIG_RAM:
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-07-11 12:13:44 +02:00
Kever Yang
6d1970fa8a rockchip: add sdram_common for common functions
There are some functions like sdram_size_mb can be re-used for
different rockchip SoCs, just put them into common file.
Add board_get_usable_ram_top() for ram_top init base on
SDRAM_MAX_SIZE.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Added SDRAM_MAX_SIZE definition for RK3036:
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

fixup: 3036 fix for sdram_common
2017-07-11 12:13:44 +02:00
Jorge Ramirez-Ortiz
d754254f20 ARM64: poplar: hi3798cv200: u-boot support for Poplar 96Boards
This port adds support for:
        1) Serial
        2) eMMC
        3) USB

It has been tested with ARM TRUSTED FIRMWARE running u-boot as the
BL33 executable [see board's README]

eMMC has been tested for reading and booting the loader and linux
kernels as well as saving the u-boot environment.

USB has been tested with ASIX networking adapter and SanDisk 7.4GB
drive.

PSCI has been tested via the reset call (PSCI executes from DDR)

The firwmare upgrade process has been tested via TFTP and USB FAT
filesystem containing the fastboot.bin image in one of the partitions.

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
2017-07-10 14:26:03 -04:00
Tom Rini
de8203653f ti816x: Enable ethernet support
The ti816x SoC revision of the ethernet IP block is handled by the
"davinci_emac" driver, rather than the "cpsw" driver as done by later
members of the family.  Enable the relevant plumbing.

Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-28 11:43:39 -04:00
Tom Rini
821560fd8e Merge git://www.denx.de/git/u-boot-imx
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	include/configs/imx6qdl_icore_rqs.h
	include/configs/imx6ul_geam.h
	include/configs/imx6ul_isiot.h
2017-06-27 09:32:37 -04:00
Tom Rini
784667d7f9 Xilinx changes for v2017.07
ZynqMP:
 - config cleanup
 - SD LS mode support
 - psu_init* cleanup
 - unmap OCM
 - Support for SMC
 
 Zynq:
 - add ddrc to Kconfig
 - add topic-miamilite board support
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iEYEABECAAYFAllJNGcACgkQykllyylKDCEBrACdE1X8RroAQZQ3cN3yEXp/OQ3V
 D+gAn1PAUvy3zT8UDiJcF1rCxptvlKlv
 =4ans
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2017.07' of git://www.denx.de/git/u-boot-microblaze

Xilinx changes for v2017.07

ZynqMP:
- config cleanup
- SD LS mode support
- psu_init* cleanup
- unmap OCM
- Support for SMC

Zynq:
- add ddrc to Kconfig
- add topic-miamilite board support
2017-06-21 07:57:37 -04:00
Michal Simek
fb4000e871 arm64: zynqmp: Check pmufw version
If PMUFW version is not v0.3 then panic.
ZynqMP switch to CCF based clock driver which requires
PMUFW to be present at certain version.
This patch ensure that you use correct and tested PMUFW
binary.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-06-20 16:42:13 +02:00
Siva Durga Prasad Paladugu
e0752bc184 arm64: zynqmp: Define routines for mmio write and read
Define routines of mmio write and read functionalities
for zynqmp platform.

Also do not call SMC from SPL because SPL is running before ATF in EL3
that's why SMCs can't be called because there is nothing to call.
zynqmp_mmio*() are doing direct read/write accesses and this patch does
the same. PMUFW is up and running at this time and there is a way to talk
to pmufw via IPI but there is no reason to implement IPI stuff in SPL if
we need just simple read for getting clock driver to work.

Also make invoke_smc as global so that it can be reused in
multile places where ever possible.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-06-20 16:42:06 +02:00
Tom Rini
ebba9d1daf Merge branch 'master' of git://git.denx.de/u-boot-sunxi 2017-06-19 08:08:40 -04:00
Semen Protsenko
fa24eca1f2 omap: Add routine for setting fastboot variables
This patch reuses new option, which allows us to expose variables
from environment to "fastboot getvar" command. Those variables must be
of "fastboot.%s" format.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
2017-06-12 08:36:21 -04:00
Tom Rini
8cb3ce64f9 Merge git://git.denx.de/u-boot-dm 2017-06-10 18:01:22 -04:00
Tom Rini
d2e1ee686a Merge branch 'master' of git://git.denx.de/u-boot-video 2017-06-10 09:48:09 -04:00
Semen Protsenko
00bbe96eba arm: omap: Unify get_device_type() function
Refactor OMAP3/4/5 code so that we have only one get_device_type()
function for all platforms.

Details:
 - Add ctrl variable for AM33xx and OMAP3 platforms (like it's done for
   OMAP4/5), so we can obtain status register in common way
 - For now ctrl structure for AM33xx/OMAP3 contains only status register
   address
 - Run hw_data_init() in order to assign ctrl to proper structure
 - Remove DEVICE_MASK and DEVICE_GP definitions as they are not used
   (DEVICE_TYPE_MASK and GP_DEVICE are used instead)
 - Guard structs in omap_common.h with #ifdefs, because otherwise
   including omap_common.h on non-omap4/5 board files breaks compilation

Buildman script was run for all OMAP boards. Result output:
    arm: (for 38/616 boards)
        all +352.5
        bss -1.4
        data +3.5
        rodata +300.0
        spl/u-boot-spl:all +284.7
        spl/u-boot-spl:data +2.2
        spl/u-boot-spl:rodata +252.0
        spl/u-boot-spl:text +30.5
        text +50.4
    (no errors to report)

Tested on AM57x EVM and BeagleBoard xM.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Rework the guards as to not break TI81xx]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-09 20:34:53 -04:00
Simon Glass
b223c1aead rockchip: rk3288: Convert clock driver to use shifted masks
Shifted masks are the standard approach with rockchip since it allows
use of the mask without shifting it each time. Update the definitions and
the driver to match.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-09 13:45:33 -06:00
Simon Glass
46864cc8e8 tegra: Init clocks even when SPL did not run
At present early clock init happens in SPL. If SPL did not run (because
for example U-Boot is chain-loaded from another boot loader) then the
clocks are not set as U-Boot expects.

Add a function to detect this and call the early clock init in U-Boot
proper.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-09 13:39:32 -06:00
Vikas Manocha
c6d9e9dbc3 SPL: Add XIP booting support
Enable support for XIP (execute in place) of U-Boot or kernel image. There is
no need to copy image from flash to ram if flash supports execute in place.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Alexandru Gagniuc <alex.g@adaptrum.com>
2017-06-09 11:23:59 -04:00
Jernej Skrabec
b98efa1db3 sunxi: video: Add support for CSC and TVE to DE2 driver
Extend DE2 driver with support for TVE driver, which will be added in
next commit. TVE unit expects data to be in YUV format, so CSC support
is also added here.

Note that HDMI driver has higher priority, so TV out is not probed if
HDMI monitor is detected.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-06-09 15:30:47 +02:00
Jernej Skrabec
a8191dfec0 sunxi: Add base address for TV encoder
This commit adds TVE base address for Allwinner H3 and H5 SoCs.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-06-09 15:30:28 +02:00
Icenowy Zheng
f6457ce578 sunxi: Add selective DRAM type and timing
DRAM chip varies, and one code cannot satisfy all DRAMs.

Add options to select a timing set.

Currently only DDR3-1333 (the original set) is added into it.

Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2017-06-08 22:37:55 +05:30
Icenowy Zheng
f43a009959 sunxi: Rename bus-width related macros in H3 DRAM code
The DesignWare DRAM controller used by H3 and newer SoCs use a bit to
identify whether the DRAM is half-width.

As H3 itself come with 32-bit DRAM, the two modes of the bit used to be
named "MCTL_CR_32BIT" and "MCTL_CR_16BIT", but for SoCs with 16-bit DRAM
they're really 8-bit and 16-bit.

Rename the bit's macro, and also rename the variable name in
dram_sun8i_h3.c.

This commit do not add 16-bit DRAM controller support, but the support
will be introduced in next commit.

Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2017-06-08 22:37:55 +05:30
Icenowy Zheng
9934aba427 sunxi: makes an invisible option for H3-like DRAM controllers
Allwinner SoCs after H3 (e.g. A64, H5, R40, V3s) uses a H3-like
DesignWare DRAM controller, which do not have official free DRAM
initialization code, but can use modified dram_sun8i_h3.c.

Add a invisible option for easier DRAM initialization code reuse.

Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2017-06-08 22:37:55 +05:30
Philipp Tomsich
ca562b630e rockchip: video: rk3399: add HDMI TX support on the RK3399
This commit enables the RK3399 HDMI TX, which is very similar to the
one found on the RK3288.  As requested by Simon, this splits the HDMI
driver into a SOC-specific portion (rk3399_hdmi.c, rk3288_hdmi.c) and
a common portion (rk_hdmi.c).

Note that the I2C communication for reading the EDID works well with
the default settings, but does not with the alternate settings used on
the RK3288... this configuration aspect is reflected by the driverdata
for the RK3399 driver.

Having some sort of DTS-based configuration for the regulator
dependencies would be nice for the future, but for now we simply use
lists of regulator names (also via driverdata) that we probe.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-06-07 21:30:50 -06:00
Philipp Tomsich
cc75afc5d7 rockchip: video: rk3399: enable HDMI output (from the rk_vop) for the RK3399
This commit adds a driver for the RK3399 VOPs capable and all the
necessary plumbing to feed the HDMI encoder. For the VOP-big, this
correctly tracks the ability to feed 10bit RGB data to the encoder.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-06-07 21:30:49 -06:00
Philipp Tomsich
d46d40474a rockchip: video: refactor rk_vop and split RK3288-specific code off
To prepare for adding the RK3399 VOP driver (which shares most of its
registers and config logic with the RK3228 VOP), this change refactors
the driver and splits the RK3288-specific driver off.

The changes in detail are:
- introduces a data-structure for chip-specific drivers to register
  features/callbacks with the common driver: at this time, this is
  limited to a callback for setting the pin polarities (between the
  VOP and the encoder modules) and a flag to signal 10bit RGB
  capability
- refactors the probing of regulators into a helper function that
  can take a list of regulator names to probe and autoset
- moves the priv data-structure into a (common) header file to be
  used by the chip-specific drivers to provide base addresses to
  the common driver
- uses a callback into the chip-specific driver to set pin polarities
  (replacing the direct register accesses previously used)
- splits enabling the output (towards an encoder) into a separate
  help function withint the common driver

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-06-07 21:30:49 -06:00
Romain Perier
fefe9d06bd rockchip: rk3288: grf: Fix shift for RK3288_TXCLK_DLY_ENA_GMAC_ENABLE
RK3288_TXCLK_DLY_ENA_GMAC_ENABLE, in GRF_SOC_CON3, is supposed to be bit
0xe and not 0xf. Otherwise, it is RGMII RX clock delayline enable and
introduces random delays and data lose.

This commit fixes the issue by replacing RK3288_TXCLK_DLY_ENA_GMAC_ENABLE
with the right shift.

Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-06-07 21:30:48 -06:00
Andy Yan
bae2f282a9 rockchip: clk: Add rv1108 clock driver
Add clock driver support for Rockchip rv1108 soc

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-06-07 07:29:25 -06:00
Andy Yan
09aa7c468c rockchip: pinctrl: Add rv1108 pinctrl driver
Add pinctrl support for Rockchip rv1108 soc

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-06-07 07:29:24 -06:00
Kever Yang
077eb31514 rockchip: pinctrl: rk3328: do not set io routing
In rk3328, some function pin may have more than one choice, and muxed
with more than one IO, for example, the UART2 controller IO,
TX and RX, have 3 choice(setting in com_iomux):
- M0 which mux with GPIO1A0/GPIO1A1
- M1 which mux with GPIO2A0/GPIO2A1
- usb2phy which mux with USB2.0 DP/DM pin.

We should not decide which group to use in pinctrl driver,
for it may be different in different board, it should goes to board
file, and the pinctrl file should setting correct iomux depends on
the com_iomux value.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-06-07 07:29:21 -06:00
Kever Yang
6f0c123713 rockchip: pinctrl: move rk3328 grf reg definition in header file
Move GRF register bit definition into GRF header file, remove
'GRF_' prefix and add 'GPIOmXn_' as prefix for bit meaning.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-06-07 07:29:21 -06:00
Kever Yang
3c421f6fa9 rockchip: rk3036: clean mask definition for grf reg
U-Boot prefer to use MASKs with SHIFT embeded, clean the Macro
definition in grf header file and pinctrl driver.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-06-07 07:29:21 -06:00
Kever Yang
1960b01034 rockchip: clock: rk3036: some fix according TRM
- hclk/pclk_div range should use '<=' instead of '<'
- use GPLL for pd_bus clock source
- pd_bus HCLK/PCLK clock rate should not bigger than ACLK

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-06-07 07:29:20 -06:00
Kever Yang
37943aaeea rockchip: rk3036: clean mask definition for cru reg
Embeded the shift in mask MACRO definition in cru header file
and clock driver.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-06-07 07:29:20 -06:00
Andy Yan
27600a5837 rockchip: rk3368: Add pinctrl driver
Add driver to support iomux setup for the most commonly
used peripherals on rk3368.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-06-07 07:29:19 -06:00