Enable USB PHY nodes on ASUS Transformers, Grouper, Enadevoru
and LG X3. This is not mandatory since driver will use default
values but preferable for new devices.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Since required drivers were merged, we can safely clean up the
board and switch to DM based driver with device tree support.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Since required drivers were merged, we can safely clean up the
board and switch to DM based driver with device tree support.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Since required drivers were merged, we can safely clean up the
board and switch to DM based driver with device tree support.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Since required drivers were merged, we can safely clean up the
board and switch to DM based driver with device tree support.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Call regulators_enable_boot_on on board init to set all regulators
with boot-on property in device tree. If regulator is not used by
any device in the device tree but is essential for the device to
work a regression will occur.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Instead of duplicating the I2C3 node and adding NVEC specific
properties, reuse the I2C3 node, extend it with NVEC specific properties
and drop properties that are not needed by NVEC. This results in a DTB
that is a bit cleaner and avoids accidentally using I2C3 and NVEC which
would have them fight over the same hardware resources.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Modify spi and usb aliases name.
Add dt-binding for usb phy define and fix usb phy reset error.
Add tpm/otpee and host_intf node.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Draco is a family of 3 boards: thuban, rastaban & etamin. Rename all
targets of the family adding the draco- prefix to increase readibility
and simplify future commits about concerning all boards of the family.
The name draco was initially used for the first target. It's deprecated
since a 2nd target was introduced. Unfortunately the draco target was
copied to the thuban target instead to be renamed. Remove it to save
unnecessary maintenance effort.
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
Reduce redundancy in code by using templates to generate the A72 boot
binaries (tispl.bin and u-boot.img) as well as R5 boot binary sysfw.itb
(for legacy boot following devices J721E and AM65x).
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Acked-by: Andrew Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
Add templates for FIT images used extensively across K3 boards with most
of the code common. This includes the FIT portions of:
- tispl.bin
- u-boot.img
- sysfw.itb (in case of legacy boot flow)
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Kernel dts import now provides bootph-all and bootph-pre-ram properties
for the properties we have been overriding so far. Drop the same.
While at this enable the DM and TIFS UARTs for programming pinmux
since they are marked reserved by board.dts
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Tested-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Kernel dts import now provides bootph-all and bootph-pre-ram properties
for the properties we have been overriding so far. Drop the same.
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Tested-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
k3-am62* SoC dtsi files now provide the following:
bootph-all: dmss secure_proxy_main dmsc k3_pds k3_clks k3_reset
main_pmx0 main_timer0 mcu_pmx0 wkup_conf chipid
bootph-pre-ram: secure_proxy_sa3 main_esm mcu_esm
Drop these from board r5 and u-boot.dtsi files as these are duplicate in
them now.
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Tested-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Sync with kernel v6.7-rc1 and sync up the u-boot dts files accordingly.
Tested-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
BCDMA can be used at SPL for OSPI boot and mem-to-mem DMA
so add "bootph-all" to BCDMA node.
Suggested-by: Nishanth Menon <nm@ti.com>
Fixes: 9a3f2b6798 ("arm: dts: k3-am625-verdin-wifi-dev-u-boot.dtsi: Fix DMA/Ethernet")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Change spl_enable_dcache so it also enable icache on SPL
initialization for the main domain part of the boot flow. This
improves bootloader booting time.
Link: https://lore.kernel.org/all/20231109140958.1093235-1-joao.goncalves@toradex.com/
Signed-off-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
Tested-by: Nishanth Menon <nm@ti.com>
main_timer0 is used by u-boot as the tick-timer. Add it to the soc
devices list so it an be enabled via the k3 power controller.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
BeagleBoard.org BeagleBone AI-64 is an open source hardware single
board computer based on the Texas Instruments TDA4VM SoC featuring
dual-core 2.0GHz Arm Cortex-A72 processor, C7x+MMA and 2 C66x
floating-point VLIW DSPs, 3x dual ARM Cortex-R5 co-processors,
2x 6-core Programmable Real-Time Unit and Industrial Communication
SubSystem, PowerVR Rogue 8XE GE8430 3D GPU. The board features 4GB
DDR4, USB3.0 Type-C, 2x USB SS Type-A, miniDisplayPort, 2x 4-lane
CSI, DSI, 16GB eMMC flash, 1G Ethernet, M.2 E-key for WiFi/BT, and
BeagleBone expansion headers.
This board family can be indentified by the BBONEAI-64-B0 in the
at24 eeprom:
[aa 55 33 ee 01 37 00 10 2e 00 42 42 4f 4e 45 41 |.U3..7....BBONEA|]
[49 2d 36 34 2d 42 30 2d 00 00 42 30 30 30 37 38 |I-64-B0-..B00078|]
Baseline of the devicetree is from v6.6-rc1
https://beagleboard.org/ai-64https://git.beagleboard.org/beagleboard/beaglebone-ai-64
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Move the omap3 beagle to the beagle vendor folder representing
BeagleBoard.org platforms.
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Move beagleplay support away from ti/am62x to it's own beagle vendor
folder.
This forms the starting point for new beagle platforms added under it's
own board vendor folder.
As part of this create all the associated files with a bare minimum
beagleplay.c file.
Suggested-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
[trini: Update k3-binman.dtsi to use full path to scheme.yaml now]
Signed-off-by: Tom Rini <trini@konsulko.com>
With the upcoming folder separation, there is no further need to depend
on am625-binman.dtsi. Duplicate the existing definitions to u-boot.dtsi
and r5.dts as appropriate.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Commit 5019170970 ("arch: arm: mach-k3: j721e: add support for UDA
FS") introduced basic UDA FS support, however, we can Take approach
similar to commit 0f1c1e8b36 ("arm: mach-k3: am625: Add support for
UDA FS"). While boot partition support with EMMC boot is useful, it is
constrained by the size of boot hardware partition itself.
In the case of K3 devices, tispl images can contain OP-TEE images that
can substantially vary in size and the u-boot image itself can vary over
time as we enable various features.
So use the CSD information in the case of EMMC_BOOT configuration being
enabled to pick boot partition or UDA FS mode operation to pick.
If EMMC_BOOT is disabled, then depend on filesystem configuration to
pick data from UDA.
Signed-off-by: Nishanth Menon <nm@ti.com>
Enable SOC_K3_J721E_J7200 when board is J7200 EVM - this allows us to
differentiate J7200 platform cleanly in board independent codebase.
Signed-off-by: Nishanth Menon <nm@ti.com>
J7200 shares quite a few characteristics with J721E. However a few sets
are different. Introduce a Kconfig to differentiate the two to allow for
new boards to be introduced in a seamless manner.
Signed-off-by: Nishanth Menon <nm@ti.com>
This file is used to emulate customer keys on TI development board
ecosystems, move it out of board/ directory and into mach-k3. And
change the relative paths to absolute paths in the binman paths.
While at it, drop the reference in verdin-binman file which is
redundant.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Manorit Chawdhry <m-chawdhry@ti.com>
This file is common for all of K3, move it out of board/ directory and
into mach-k3. And change the relative paths to absolute paths in the
binman paths.
While at it, drop the reference in verdin-binman file which is
redundant.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Andrew Davis <afd@ti.com>
SYSFW is only ever loaded by the R5 core, move the code into that
directory. While here also move the related Kconfig symbols.
Signed-off-by: Andrew Davis <afd@ti.com>
The kconfig option SPL means this build supports SPL but not that
this build is SPL, nor that this build is the SPL running on R5.
For options that are for R5 SPL use CPU_V7R.
Signed-off-by: Andrew Davis <afd@ti.com>
This makes it clear these are only to be used by the R5 builds of SPL.
And this will be used to later more cleanly split the two builds.
Signed-off-by: Andrew Davis <afd@ti.com>
Currently each set of board targets from a vendor is selected inside
the board directory for that vendor. This has the problem of multiple
targets, one from each vendor, being selectable at the same time.
For instance you can select both TARGET_AM654_A53_EVM and
TARGET_IOT2050_A53 in the same build.
To fix this we need to move the target board choice to a common location
for each parent SoC selection. Do this in arch/arm/mach-k3.
Signed-off-by: Andrew Davis <afd@ti.com>
Currently each set of board targets from a vendor is selected inside
the board directory for that vendor. This has the problem of multiple
targets, one from each vendor, being selectable at the same time.
For instance you can select both TARGET_AM654_A53_EVM and
TARGET_IOT2050_A53 in the same build.
To fix this we need to move the target board choice to a common location
for each parent SoC selection. Do this in arch/arm/mach-k3.
Signed-off-by: Andrew Davis <afd@ti.com>
Currently each set of board targets from a vendor is selected inside
the board directory for that vendor. This has the problem of multiple
targets, one from each vendor, being selectable at the same time.
For instance you can select both TARGET_AM654_A53_EVM and
TARGET_IOT2050_A53 in the same build.
To fix this we need to move the target board choice to a common location
for each parent SoC selection. Do this in arch/arm/mach-k3.
Signed-off-by: Andrew Davis <afd@ti.com>
Currently each set of board targets from a vendor is selected inside
the board directory for that vendor. This has the problem of multiple
targets, one from each vendor, being selectable at the same time.
For instance you can select both TARGET_AM654_A53_EVM and
TARGET_IOT2050_A53 in the same build.
To fix this we need to move the target board choice to a common location
for each parent SoC selection. Do this in arch/arm/mach-k3.
Signed-off-by: Andrew Davis <afd@ti.com>
Currently each set of board targets from a vendor is selected inside
the board directory for that vendor. This has the problem of multiple
targets, one from each vendor, being selectable at the same time.
For instance you can select both TARGET_AM654_A53_EVM and
TARGET_IOT2050_A53 in the same build.
To fix this we need to move the target board choice to a common location
for each parent SoC selection. Do this in arch/arm/mach-k3.
Signed-off-by: Andrew Davis <afd@ti.com>
Currently each set of board targets from a vendor is selected inside
the board directory for that vendor. This has the problem of multiple
targets, one from each vendor, being selectable at the same time.
For instance you can select both TARGET_AM654_A53_EVM and
TARGET_IOT2050_A53 in the same build.
To fix this we need to move the target board choice to a common location
for each parent SoC selection. Do this in arch/arm/mach-k3.
Signed-off-by: Andrew Davis <afd@ti.com>
This reverts commit 6cdf6b7a34. This is
part of a series trying to make use of the arm64 hardware features for
tracking dirty pages. Unfortunately this series causes problems for the
AC5/AC5X SoCs. Having exhausted other options the consensus seems to be
reverting this series is the best course of action.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
This reverts commit 836b8d4b20. This is
part of a series trying to make use of the arm64 hardware features for
tracking dirty pages. Unfortunately this series causes problems for the
AC5/AC5X SoCs. Having exhausted other options the consensus seems to be
reverting this series is the best course of action.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
This reverts commit c1da6fdb5c. This is
part of a series trying to make use of the arm64 hardware features for
tracking dirty pages. Unfortunately this series causes problems for the
AC5/AC5X SoCs. Having exhausted other options the consensus seems to be
reverting this series is the best course of action.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
This fixes a regression in the eMMC fast boot mode case where the buffer
was missing 464 bytes.
The code figures out how many bytes must at least be fetched to honor
the current read, rounds that up to the ss->pagesize [which is a no-op
in the USB download case because that has ->pagesize==1], fetches that
many bytes, but then recorded the original upper bound as the new end of
the valid data. However, this did not take into account the rounding up
to the ss->pagesize. Fix this by recording the actual bytes downloaded.
Fixes: 4b4472438f ("imx: spl_imx_romapi: avoid tricky use of spl_load_simple_fit() to get full FIT size")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Aligning addresses and sizes causes overhead which is unnecessary when we
are not loading from block devices. Remove bl_len when it is not needed.
For example, on iot2050 we save 144 bytes with this patch (once the rest of
this series is applied):
add/remove: 0/0 grow/shrink: 0/3 up/down: 0/-144 (-144)
Function old new delta
spl_load_simple_fit 920 904 -16
load_simple_fit 496 444 -52
spl_spi_load_image 384 308 -76
Total: Before=87431, After=87287, chg -0.16%
We use panic() instead of BUILD_BUG_ON in spl_set_bl_len because we still
need to be able to compile it for things like mmc_load_image_raw_sector,
even if that function will not be used.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For filesystems, filename serves the same purpose as priv. However,
spl_load_fit_image also uses it to determine whether to use a DMA-aligned
buffer. This is beneficial for FAT, which uses a bounce-buffer if the
destination is not DMA-aligned. However, this is unnecessary now that
filesystems set bl_len to ARCH_DMA_MINALIGN instead. With this done, we can
remove filename entirely.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Simplify things a bit for callers of spl_load_info->read by refactoring it
to use units of bytes instead of bl_len. This generally simplifies the
logic, as MMC is the only loader which actually works in sectors. It will
also allow further refactoring to remove the special-case handling of
filename. spl_load_legacy_img already works in units of bytes (oops) so it
doesn't need to be changed.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove NULL assignments to fields in spl_load_info when .load doesn't
reference these fields. This can result in more efficient code. filename
must stay even if it is unused, since load_simple_fit uses it.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Several AT91 boards are quite close to their SPL size limit. For example,
sama5d27_wlsom1_ek_mmc is just 173 bytes short of its limit and doesn't
even fit with older GCCs.
All AT91 processors should have thumb support. Enable SYS_THUMB_BUILD. This
shrinks SPL by around 30%.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Add initial support for STM32MP2 SoCs family.
SoCs information are available here :
https://www.st.com/content/st_com/en/campaigns/microprocessor-stm32mp2.html
Migrate all MP1 related code into stm32mp1/ directory
Create stm32mp2 directory dedicated for STM32MP2 SoCs.
Common code to MP1, MP13 and MP25 is kept into
arch/arm/mach-stm32/mach-stm32mp directory :
- boot_params.c
- bsec
- cmd_stm32key
- cmd_stm32prog
- dram_init.c
- syscon.c
- ecdsa_romapi.c
For STM32MP2, it also :
- adds memory region description needed for ARMv8 MMU.
- enables early data cache before relocation.
During the transition before/after relocation, the MMU, initially setup
at the beginning of DDR, must be setup again at a correct address after
relocation. This is done in enables_caches() by disabling cache, force
arch.tlb_fillptr to NULL which will force the MMU to be setup again but
with a new value for gd->arch.tlb_addr. gd->arch.tlb_addr has been
updated after relocation in arm_reserve_mmu().
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add STM32MP257F Evaluation board support. It embeds a STM32MP257FAI SoC,
with 4GB of DDR4, TSN switch (2+1 ports), 2*USB typeA, 1*USB2 typeC,
SNOR OctoSPI, mini PCIe, STPMIC2 for power distribution ...
Sync device tree with kernel v6.6-rc1.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
When building with AARCH64 defconfig, we got warnings, fix them.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Limit DDR usage under 4GB boundary on STM32MP regardless of
memory size declared in device tree.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
When building with AARCH64 defconfig, we got warnings for debug
message
- format '%x' expects argument of type 'unsigned int',
but argument 3 has type 'size_t' {aka 'long unsigned int'}).
- format '%lx' expects argument of type 'long unsigned int',
but argument 2 has type 'phys_addr_t' {aka 'long long unsigned
int'}
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
In case there is no RAM driver retrieve RAM size from DT as fallback.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This fixes the following compilation error in ARM64:
arch/arm/mach-stm32mp/dram_init.c: In function ‘board_get_usable_ram_top’:
arch/arm/mach-stm32mp/dram_init.c:59:45: error: ‘DCACHE_DEFAULT_OPTION’ undeclared (first use in this function)
59 | mmu_set_region_dcache_behaviour(reg, size, DCACHE_DEFAULT_OPTION);
| ^~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The sysreset uclass unconditionally provides a definition of the
reset_cpu() function. So does the exynos soc code. Fix the build with
SYSRESET enabled by omitting the function from the soc code in that
case. The code still needs to be kept around for use in SPL.
This commit was inspired by commit 6e19dc84c1 ("sunxi: Avoid duplicate
reset_cpu with SYSRESET enabled").
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
arch/arm/include/asm/arch/gpio.h relies on definitions from cpu.h.
Include it explicitly in gpio.h. Otherwise next build error may occur:
In file included from ./arch/arm/include/asm/gpio.h:7,
from include/cros_ec.h:14,
from board/samsung/common/board.c:8:
./arch/arm/include/asm/arch/gpio.h:1357:4:
error: 'EXYNOS4_GPIO_PART1_BASE' undeclared here
(not in a function); did you mean 'EXYNOS4_GPIO_MAX_PORT'?
1357 | { EXYNOS4_GPIO_PART1_BASE, EXYNOS4_GPIO_MAX_PORT_PART_1 },
| ^~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
samsung_get_base_swreset() is called in soc.c, but corresponding header
with its prototype is not included. Fix this to avoid possible build
errors.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The H616 SoC family has support for several types of DRAM: DDR3,
LPDDR3, DDR4 and LPDDR4.
At the moment, the driver only supports DDR3 and LPDDR3 memory.
Let's extend the driver to support the LPDDR4 memory. This type
of memory widely used in device with T507(-H) SoC and new orangepi
zero3 with H618.
The compatibility with T507 is not yet complete, because there
is difference in the phy_init array.
The LPDDR4-2133 timings correspond to DRAM Rayson RS1G32LO4D2BDS-53BT
found on the NOR SPI from the Orangepi Zero 3 4GB.
Signed-off-by: Mikhail Kalashnikov <iuncuim@gmail.com>
Tested-by: Piotr Oniszczuk <piotr.oniszczuk@gmail.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
The original H616 DDR3 ODT configuration code wrote board specific values
into a sequence of paired registers.
For LPDDR3 support we needed to special-case one group of registers,
because for that DRAM type we need to write 0 into the lower register of
each pair. That already made the code less readable.
LPDDR4 support will make things even messier, so let's refactor that
code now: We allow to write different values into the lower and upper
half of each pair. The masking is moved into a macro, and use in each
write statement.
The effect is not as obvious yet, as we don't need the full flexibility at
the moment, but the motivation will become clearer with LPDDR4 support.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Mikhail Kalashnikov <iuncuim@gmail.com>
On boards using the AXP313 PMIC, the DRAM rail is often not setup
correctly at reset time, so we have to program the PMIC very early in
the SPL, before running the DRAM initialisation.
Add a simple AXP313 PMIC driver that knows about DCDC2(CPU) and
DCDC3(DRAM), so that we can bump up the voltage before the DRAM init.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The MMC controller driver is (and ought to be) the only user of these
register definitions. Put them in a header next to the driver to remove
the dependency on a specific ARM platform's headers.
Due to the sunxi_mmc_init() prototype, the file was not renamed. None of
the register definitions were changed.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
To quote the author:
Since commit [1], Ethernet is broken on TI AM62 and AM64 platforms.
The commit [1] is not the culprit. It just unearths the problem by fixing
the error check in k3-udma.c. This issue was silently being ignored earlier
due to wrong error check. [NULL instead of FDT_ADDR_T_NONE].
Fix the issue by adding the necessary register spaces for the u-boot K3-UDMA
driver for AM62 and AM64 platforms.
These properties will eventually make it into the SoC DTSi files [2] after
which these can be dropped from k3-*-u-boot.dtsi files.
[1] - 5fecea171de3dd ("treewide: use dev_read_addr_*_ptr() where appropriate")
[2] - https://lore.kernel.org/linux-arm-kernel/20230810174356.3322583-1-vigneshr@ti.com/
Update main_bcdma and main_pktdma nodes for native configuration in the
absence of DM services.
Drop duplicate main_pktdma node in k3-am642-sk-u-boot.dtsi.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Update main_bcdma and main_pktdma nodes for native configuration in the
absence of DM services.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Add support for a semihosting fallback on 32-bit ARM. The assembly is
lightly adapted from the irq return code, except there is no offset
since lr already points to the correct instruction. The C side is mostly
like ARM64, except we have fewer cases to deal with.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
U-Boot runs in supervisor mode. On ARMv6 and lower, software interrupts
are taken in supervisor mode. When entering an interrupt, the link
register is set to the address of the next instruction. However, if we
are already in supervisor mode, this clobbers the link register. The
debugger can't help us, since by the time it notices we've taken a
software interrupt, the link register is already gone. Work around this
by moving the return address to another register.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
When we take a software interrupt, we are already in supervisor mode.
get_bad_stack assumes we are not in supervisor mode so it can clobber
the stack pointer. This causes us to have an invalid stack once that
macro finishes. Revert back to the get_bad_stack_swi macro which was
previously removed.
Fixes: 41623c91b0 ("arm: move exception handling out of start.S files")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
_ Fix compilation issue when SYS_DCACHE_OFF and/or SYS_DCACHE_SYS are enabled
_ Fix issue following DT sync with kernel 6.3 for stm32mp15xx-ev1 and DHSOM SoM
_ Enable TCP, IPv6, wget on DH STM32MP15 DHSOM
_ Limit u-boot.itb size to 0x160000 bytes on DH STM32MP15 DHSOM
_ Read auth stats and boot_partition from tamp
- Fix some issues Coverity has reported, update MAINTAINERS file,
another bootstd fix, typo fix in error message, gitignore fix and
update TI's URL in many places.
Keep track of the re-entries with help of the lr register.
This binary can be re-used and called from various BROM functions.
Only when it's called from the part that handles SPI, NAND or EMMC
hardware it needs to early return to BROM ones.
In download mode when it handles data on USB OTG and UART0
this section must be skipped.
Unlike newer Rockchip SoC models the rk3066 BROM code does not have built-in
support to enter download mode on return to BROM. This binary must check
the boot mode register for the BOOT_BROM_DOWNLOAD flag and reset if it's set.
It then returns to BROM to the end of the function that reads boot blocks.
From there the BROM code goes into a download mode and waits for data
on USB OTG and UART0.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Provide configuration to read cpuid and generate a persistent
MAC address in ethaddr
Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
RV1126 fails to boot on 2024.01-rc1.
Commit 9e644284ab ("dm: core: Report bootph-pre-ram/sram node as
pre-reloc after relocation") changed the behaviour of bootph-pre-ram, to
limit nodes to spl phase. This caused rv1126 boards to fail to boot with
the current dts.
This patch updates the pmu/grf nodes to bootph-all tags as they are
needed in all phases. This fixes the boot issue on rv1126 boards.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Obtain from TAMP backup register information about image authorization
status and partition id used for booting. Store this info in
environmental variables ("boot_auth" and "boot_part" correspondingly).
Image authorization supported values:
0x0 - No authentication done
0x1 - Authentication done and failed
0x2 - Authentication done and succeeded
These values are stored to TAMP backup register by Trusted Firmware-A [1].
Testing:
STM32MP> print boot_part
boot_part=1
STM32MP> print boot_auth
boot_auth=2
[1] https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git/commit/?h=refs/heads/integration&id=ab2b325c1ab895e626d4e11a9f26b9e7c968f8d8
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The patch fixed by this commit renders ST STM32MP15xx EV1 board and
all DHSOM SoM based boards unbootable from SPI NOR. Fix the damage
by updating -u-boot.dtsi to match the stm32mp15-pinctrl.dtsi update.
Fixes: 08002ffd08 ("ARM: dts: stm32mp: alignment with v6.3")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
While 23e20b2fa6 ("arm: stm32mp: Fix compilation issue when
SYS_DCACHE_OFF and/or SYS_DCACHE_SYS are enabled") tried fixing
this issue, fix it really by adding #if checks for SYS_ICACHE_OFF
and SYS_DCACHE_OFF.
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
QuartzPro64 is a Rockchip RK3588 based SBC by Pine64.
UART and boot over SD/eMMC/RJ45 are tested to work.
Linux commits from next-20231013:
8152d3d070a9 ("arm64: dts: rockchip: Add QuartzPro64 SBC device tree")
Signed-off-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Cc: Eugen Hristev <eugen.hristev@collabora.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Ondrej Jirman <megi@xff.cz>
The migration deadline for moving to DM_SCSI was v2023.04. A further
reminder was sent out in August 2023 to the remaining platforms that had
not migrated already, and that a few more over the line (or configs
deleted).
With this commit we:
- Rename CONFIG_DM_SCSI to CONFIG_SCSI.
- Remove all of the non-DM SCSI code. This includes removing other
legacy symbols and code and removes some legacy non-DM AHCI code.
- Some platforms that had previously been DM_SCSI=y && SCSI=n are now
fully migrated to DM_SCSI as a few corner cases in the code assumed
DM_SCSI=y meant SCSI=y.
Signed-off-by: Tom Rini <trini@konsulko.com>
The include <asm/arch/cpu.h> references values in <asm/arch/omap3.h> and
so include it directly here rather than rely on indirect inclusion.
Signed-off-by: Tom Rini <trini@konsulko.com>
Xilinx is using standard mtd partition layout for quite a long time. It is
used for testing purpose on evaluation boards.
Also #address/size-cells shouldn't be present without nodes which should
use them that's why move them from zynq-7000.dtsi to nand/nor nodes
directly.
The patch was tested on zc706 and zedboard(with also increasing max
frequency and rx bus width).
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/4c3348981bba32d3892194420d78fe8621c47534.1698837725.git.michal.simek@amd.com
SMMU is disabled by default and not all masters can be enabled at the same
time because of limited number of entries. That's why comment all iommu
properties but keep them for reference in DT. In XEN case they should be
added back and Xen should have SMMU enabled by default.
Also add IDs for DP and DPDMA.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/e868c27c52ded5d8ef25f75ba394b1ab3b31b80a.1698825657.git.michal.simek@amd.com
Mini U-Boot is running out of OCM and it's only purpose is to program non
volatile memories. There are different configurations which ospi/qspi can
be that's why describe them via DT.
DT binding is already approved that's why there is no reason not to add it.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/a99a8d72201a782fc811715942dea97fb5ab583b.1698329087.git.michal.simek@amd.com
Mini U-Boot is running out of OCM and it's only purpose is to program non
volatile memories. There are different configurations which ospi/qspi can
be that's why describe them via DT.
DT binding is already approved that's why there is no reason not to add it.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/9518ab1c4299a45e800b8611172edd78c9243132.1698329087.git.michal.simek@amd.com
Mini U-Boot is running out of OCM and it's only purpose is to program non
volatile memories. There are different configurations which qspi can be
that's why describe them via DT.
DT binding is already approved that's why there is no reason not to add it.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/e7d31a9d9c4a76e171eefc619f31fabd0831a614.1698329087.git.michal.simek@amd.com
Mini U-Boot is running out of OCM and it's only purpose is to program non
volatile memories. There are different configurations which qspi can be
that's why describe them via DT.
DT binding is already approved that's why there is no reason not to add it.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/28b3cdd7e91b2b4c3c36d0bf65aa5bac042f248c.1698329087.git.michal.simek@amd.com
