Currently k2 spi boot is broken as the image header
is getting copied to an invalid memory location
CONFIG_SYS_TEXT_BASE - sizeof (struct image_size)
which maps to 0xc000000 - 0x40 = 0xbffffc0 being a reserved
location.
We cannot change the CONFIG_SYS_TEXT_BASE address as the single
stage boots like UART boot will need the address to be 0xc000000
hence override the spl_get_load_buffer to have image_header
address as CONFIG_SYS_TEXT_BASE aka 0xc000000
Signed-off-by: Keerthy <j-keerthy@ti.com>
Voltage regulator LTC3882 device has 0.5% voltage read error.
So for NXP SoC devices this generally equates to 2mV
Update set_voltage_to_LTC for below:
1.Add coorection of upto 2mV in voltage comparison
to take care of voltage read error of voltage regulator
2.Add loop max count kept as 100 to avoid infinte loop.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
ls1088ardb-pb and ls1088ardb both boards are ls1088a based soc,
board type detection is dynamic at boot time
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
I2C is used to access DDR SPD in the DDR initialization for SPL. In
i2c_write process, get_timer() will be called. In board_init_f for SPL,
timer_init() is not called before. The system counter is not enabled and
the counter frequency is not set to 12.5MHz in SPL. The parameters for
do_div() are zero too.
It could not be found until CONFIG_USE_PRIVATE_LIBGCC is enabled in
default. When CONFIG_USE_PRIVATE_LIBGCC is enabled, U-Boot will use its
own set of libgcc functions. As the parameters for do_div() are zero,
__div0 will be called. Then the processor will stay in an endless loop
after calling hang().
This patch will add timer_init() in board_init_f for SPL and fix a
series of issues it caused.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1012a2g5rdb/ls1012afrdm/ls1012afrwy_tfa_defconfig to be
loaded by trusted firmware
- define BOOTCOMMAND for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[YS: remove unnecessary braces]
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1012aqds_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Includes environment.h file in ls1012aqds.c Also, enables
pfe validation
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1012ardb_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- enable PFE validation for secure boot
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1043aqds_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1043ardb_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- FMAN and QE address changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1046aqds_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- FMAN address changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1046ardb_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- FMAN address changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
Signed-off-by: York Sun <york.sun@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Rock960 is a family of boards based on Rockchip RK3399 SoC from Vamrs.
It consists of Rock960 (Consumer Edition) and Ficus (Enterprise Edition)
96Boards.
Below are some of the key differences between both Rock960 and Ficus
boards:
1. Different host enable GPIO for USB
2. Different power and reset GPIO for PCI-E
3. No Ethernet port on Rock960
The common board support will be utilized by both boards. The device
tree has been organized in such a way that only the properties which
differ between both boards are placed in the board specific dts and
the reset of the nodes are placed in common dtsi file.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[Added instructions for SD card boot]
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
ax25-ae350 use CONFIG_OF_BOARD via a2 and CONFIG_SYS_SDRAM_BASE
to boot from ram which allow the board to override the fdt
address originally.
But after this patch
riscv: save hart ID and device tree passed by prior boot stage
It provide prior_stage_fdt_address which offer a temporary
memory address to keep the dtb address passing from loader(gdb)
to u-boot with a1.
So passing via a2 and CONFIG_SYS_SDRAM_BASE is redundant and
can be removed. And it also somehow may corrupted BBL if it
was be arranged in CONFIG_SYS_SDRAM_BASE.
In board_fdt_blob_setup()
When boting from ram:
prior_stage_fdt_address will be use to reserved dtb temporarily.
When booting from ROM:
dtb will be pre-burned in CONFIG_SYS_FDT_BASE, if it is flash base.
Or CONFIG_SYS_FDT_BASE maybe a memory map space (NOT RAM or ROM)
which is provided by HW.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
This patch adds S-mode defconfigs for QEMU virt machine so
that we can run u-boot in S-mode on QEMU using M-mode runtime
firmware (BBL or equivalent).
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
When u-boot runs in S-mode, the M-mode runtime firmware
(BBL or equivalent) uses memory range in 0x80000000 to
0x80200000. Due to this, we cannot use 0x80000000 as
SYS_TEXT_BASE when running in S-mode. Instead for S-mode,
we use 0x80200000 as SYS_TEXT_BASE.
Even Linux RISC-V kernel ignores/reserves memory range
0x80000000 to 0x80200000 because it runs in S-mode.
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Bundle DTBs for R8A7795, R8A7796 ULCB variants into single U-Boot
build and let U-Boot choose between them based on the CPU model.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Bundle DTBs for R8A7795, R8A7796, R8A77965 Salvator-X variants
into the single U-Boot build and let U-Boot choose between them
based on the CPU model.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Drop unused MSTP macros from Gen3 boards. These are no longer needed
as the boards are using clock framework to manipulate clock.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
A few Raspberry Pi specific changes this time:
- Allow 2nd MMC device
- Support RPi 3 Model A+
- Allow UUID to find filesystem
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=W6tE
-----END PGP SIGNATURE-----
Merge tag 'signed-rpi-next' of git://github.com/agraf/u-boot
Patch queue for rpi - 2018-12-03
A few Raspberry Pi specific changes this time:
- Allow 2nd MMC device
- Support RPi 3 Model A+
- Allow UUID to find filesystem
Add Raspberry Pi 3 Model A+ to list of models, the revision code is 0xE
according to the list on raspberrypi.org.
Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Replace various third party lists of Raspberry Pi revision codes in a
comment with the list on raspberrypi.org.
Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch switches MCR3000 board to the new DM watchdog.
The change in u-boot.lds is because MCR3000.o grows a bit
with this patch and doesn't fit anymore below env_offset on
some versions of GCC.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
OnRISC Baltos series uses SoM with tps65910 PMIC, so remove
"power/tps65217.h" header inclusion.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use DM for both MMC and USB subsystems and use dedicated DTS
for U-Boot configuration.
Disable SPL support for GPIO and remove EVMSK leftover for
DDR power control via GPIO.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Instead of "base + offset" define all registers right away
and access them later via direct defines.
Generate bit masks with "BIT" macro.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We do real CPU clock measurement with help of built-in
counters. Thus we may accommodate different real clock values
that appear in different FPA images instead of relying on
something hard-coded in the .dtb.
And while at it make make SDIO base address define
look similar to others with casting to "(void *)".
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Since we now do advanced CPU identification in
generic ARC code there's no need to have per-board
hardcoded data.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Convert TPM fully to DM
Tidy up sandbox I2C emulation
Add a 'make qcheck' target for faster testing
A few other misc things
(dropped the final patch which breaks clang for some reason)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlwBjx8ACgkQfxc6PpAI
rebWEAf+PMc/M3X6cCKm+8P9xTNFv0gv234HVke1eTDG3eyZB6WQnJn5CS0LwyPj
JUfwk4xK0Sqev/sQ6RuzmxmPAgla6UrEFB355tiZRBtFsMgf8bfevOqbxVqMbZl/
bOe4YsFJ3sAgQDuhi2C5xzm2speGtaB8Qy8s1Zlv2sx3zEnLgRqVgeEVHzulZsk3
gAlWKN3ys6EueYnOladjrrvrfOX8SQKYbThI+ACy7suZbtasGRITwP/4fQoXtmOl
39e9WsiW6DBRW1sxNxpixrOS5trgWjOOFiKlY3GNWP+N34+9vYASwuBWwRWqfgXo
cmelT6AcGiPUbHyr4k0CJHKCJlSbaQ==
=p83K
-----END PGP SIGNATURE-----
Merge tag 'pull-30nov18' of git://git.denx.de/u-boot-dm
Fix sound on sandbox
Convert TPM fully to DM
Tidy up sandbox I2C emulation
Add a 'make qcheck' target for faster testing
A few other misc things
(dropped the final patch which breaks clang for some reason)
Some factory data is stored in the SPI NOR and needs to get extracted
from there into U-Boot environment variables.
This patch also includes a board-specific command "fd_write" to
provide some dummy / default values for this factory-data in the SPI
NOR flash. This should only be necessary for testing purposes though.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
For testing purpose use zcu102 which has SD at controller 1 and this can
be used for testing this mini configuration.
U-Boot 2018.11-00279-gdc482e7ee092 (Nov 30 2018 - 10:22:56 +0100)
Model: ZynqMP MINI EMMC1
Board: Xilinx ZynqMP
DRAM: 512 MiB
EL Level: EL3
MMC: sdhci@ff170000: 0
In: dcc
Out: dcc
Err: dcc
ZynqMP>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
For testing purpose use zcu100 which has SD at controller 0 and this can
be used for testing this mini configuration.
U-Boot 2018.11-00281-gc5d48466e76e (Nov 30 2018 - 10:41:05 +0100)
Model: ZynqMP MINI EMMC0
Board: Xilinx ZynqMP
DRAM: 512 MiB
EL Level: EL3
MMC: sdhci@ff160000: 0
In: dcc
Out: dcc
Err: dcc
ZynqMP>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
If only usb ethernet gadget is enabled it can start automatically.
If more gagdets are enabled usb ethernet gadget can be bind by
"bind /amba/usb1@ff9e0000/dwc3@fe300000 usb_ether" (on zcu100)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This configuration is useful when you want to run small u-boot and
perform DDR memory test to make sure that DDR is properly configured.
It is use for board bringup because alternative u-boot memory tests is
quite good.
Configuration is running out of OCM.
As is done for others mini configurations 0x80 bytes for variables is
enough and only default variables are stored there.
Alternative memtest is enabled and also 2GB of DDR via DTS files.
Configuration is enabling ZYNQMP_PSU_INIT_ENABLED and include psu_init()
from zcu102 for testing purpose.
In case of size issue this can be moved to SPL configuration as is done
for mini_qspi configuration but it is not a problem now.
Log:
U-Boot 2018.11-00268-gbd58b8ba8915 (Nov 29 2018 - 15:33:35 +0100)
Model: ZynqMP MINI
Board: Xilinx ZynqMP
DRAM: WARNING: Initializing TCM overwrites TCM content
2 GiB
EL Level: EL3
In: dcc
Out: dcc
Err: dcc
ZynqMP>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
At present many TPM calls assume there is only one TPM in the system and
look up this TPM themselves. This is inconsistent with driver model, which
expects all driver methods to have a device parameter. Update the code to
correct this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Wire up mini_qspi SPL with zcu102 for testing purpose.
Normally mini u-boot runs with FSBL/SPL for certain board.
Enabling SPL and configuration from zcu102 helps with testing.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This adds a general board file based on MT7623 SoCs from MediaTek.
As this u-boot is loaded by MTK proprietary preloader, there is no
low level initializtion codes.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a general board file based on MT7629 SoCs from MediaTek.
Apart from the generic parts (cpu) we add some low level init codes
and initialize the early clocks.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In legacy CONFIG_HARD_SPI initalizing spi_init code, which
was removed during dm conversion cleanup.
So remove the dead instances of CONFIG_HARD_SPI, and related
code.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
DM_SERIAL is selected by TARGET_CHILIBOARD, so there is no reason to
keep code that will not be built. Remove it.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch mostly enables DM drivers in board defconfig and all their
dependencies. Additionally we remove ethernet platform data, as all
details are in device-tree now.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now we have moved all the Amlogic board support to common generic board code,
we can move the identical board_init() and ft_board_setup() functions to
weak functions into the board-common mach-meson file.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
We are about to add support for the Amlogic AXG SoC. While very close to
the Gx SoC family, we will need to handle a few thing which are different
in this SoC. Rework the meson arch directory to prepare for this.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Rework the board SYS_BOARD, SYS_VENDOR and SYS_CONFIG_NAME setup by moving
the board Kconfig into the mach-meson Kconfig to make it easier to add
new boards for a SoC architecture and add a custom config header or custom
board handler for a platform.
This drops the board CONFIGs and the duplicate boards configs headers in
favor of a single meson64.h config header.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The nanopi-k2 and the odroid-c2 are similar enough to be supported
by the same u-boot board. This change use odroid-c2 u-boot board
for the nanopi-k2 as well. Dedicated defconfig are kept to customize
the names and device tree.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Khadas vim2 derive from amlogic s912 reference design (Q200).
This patch moves the khadas-vim2 board support to a generic Q200 board,
while keeping a dedicated defconfig to customize the names and device tree.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Khadas vim and the libretech aml-s905x-cc (aka Potato) derive
from amlogic s905x reference design (P212).
All the code in these board is a copy/paste from the p212, which is
tedious to maintain. This change use p212 u-boot board for all these
boards, while keeping a dedicated defconfig to customize the names
and device tree.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
We have a few things in the memory map now, so add documentation for this
to avoid confusion. Also note that it is possible to run all tests now.
Signed-off-by: Simon Glass <sjg@chromium.org>
If SYS_LONGHELP is disabled the following warning is generated:
board/xilinx/zynq/cmds.c:496:13: warning: ‘zynq_help_text’ defined but
not used [-Wunused-variable]
Normal way for fixing this is to guard the whole variable.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The VCU disable bit(8) in IP disable register of efuse
is valid only if PL powered up and hence PL powerup status
has to be considered while determining the CG part also.
This patch considers the PL powerup status and ignores the VCU
disable bit if PL not powered up.
This fixes the issue of "unknown" id for CG parts if PL not powered up
and VCU bit(8) is not set.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
QEMU specifies the location of Linux (supplied with the -kernel
argument) in the device tree using the riscv,kernel-start and
riscv,kernel-end properties. We currently rely on the SBI implementation
of BBL to run Linux and therefore embed Linux as payload in BBL. This
causes an issue, because BBL detects the kernel properties in the device
tree and ignores the Linux payload as a result.
Work around this issue by clearing the kernel properties in the device
tree before booting Linux.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
QEMU embeds the location of the kernel image in the device tree. Store
this address in the environment as variable kernel_start. It is used in
the board-local distro boot command QEMU to boot the kernel with the
U-Boot device tree. The QEMU boot command is added as the first boot
target device.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
QEMU provides a device tree, which is passed to U-Boot using register
a1. We are now able to directly select the device tree with the
configuration CONFIG_OF_PRIOR_STAGE. Replace the hard-coded address in
qemu-riscv with it.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
This is now deprecated and no board is using it. Drop it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
This function is really just a call to uclass_get_device() and there is no
reason why the caller cannot do it. Update sandbox and snow accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
If we want to control which network interface is actually used, we have to
issue 'setenv ethrotate no'. If ethrotate is not set any interface may be
used.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The command to set environment variables is setenv.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use the correct function to get the uncached address to access the SoC
registers.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This is needed to set the LEDs automatically to a default state, as
configured in the dts.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Configure digital vs analog GPIOs as needed on this board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add entries for the pine64-lts and pinebook configs.
Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Update the README file to add r5 build support and system
firmware support.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Add initial defconfig support for AM65x
that runs on R5.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Add initial support for AM654 based EVM running on R5.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
This add the initial support of the broadcom reference
board bcm968580xref with a bcm6858 SoC.
This board has 512 MB of ram, 256 MB of flash (nand),
2 usb port, 1 uart, 4 ethernet ports (LAN), 1 ethernet port (WAN).
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Currently devices on the virtio bus is not automatically enumerated,
which means peripherals on the virtio bus are not discovered by their
drivers. This uses board_init() to do the virtio enumeration.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a Kconfig file in the board directory, so that some
board-specific options can be specified there.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With the virtio net and blk drivers, we can do more stuff with some
useful commands. Imply those in the board Kconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently devices on the virtio bus is not automatically enumerated,
which means peripherals on the virtio bus are not discovered by their
drivers. This uses board_init() to do the virtio enumeration.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
OrangePi Lite2 is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- AP6356S Wifi/BT
- USB 2.0, USB 3.0 Host, OTG
- HDMI port
- 5V/2A DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner A64 has a I2C controller, which is in the R_ MMIO zone and has
two groups of pinmuxes on PL bank, so it's called R_I2C.
Add support for this I2C controller and the pinmux which doesn't conflict
with RSB.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Acked-by: Jagan Teki <jagan@openedev.com>
board/freescale/mx8mq_evk/README has been introduced by mistake
in commit d0dd73974c ("imx: add i.MX8QXP MEK board support")
Remove it for now as this should be introduced when mx8mq_evk
support is in place.
Reported-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Networking support for all TI K2 boards converted to use DM model and
CONFIG_DM_ETH enabled in all corresponding defconfig files, hence drop
unused non DM K2 networking code.
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Real marketing name of the board was recently updated so
to accommodate that change renaming the board and all
related to it.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Banana Pi M2 Zero is a board by Sinovoip with Allwinner H2+ SoC, 16-bit
512MiB DDR3 memory, a MicroSD slot, two MicroUSB ports (one OTG and one
powering-only) and a miniHDMI port.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
[jagan: Fixed board MAINTAINERS file]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
At the moment we rely on the infamous get_ram_size() function to learn
the actual DRAM size in U-Boot proper. This function has two issues:
1) It only works if the DRAM size is a power of two. We start to see
boards which have 3GB of (usable) DRAM, so this does not fit anymore.
2) As U-Boot has no notion of reserved memory so far, it will happily
ride through the DRAM, possibly stepping on secure-only memory. This
could be a region of DRAM reserved for OP-TEE or some other secure
payload, for instance. It will most likely crash in that case.
As the SPL DRAM init routine has very accurate knowledge of the actual
DRAM size, lets propagate this wisdom to U-Boot proper.
We re-purpose a currently reserved word in our SPL header for that.
The SPL itself stores the detected DRAM size there, and bumps the SPL
header version number in that case. U-Boot proper checks for a valid
SPL header and a high enough version number, then uses the DRAM size
from there. If the SPL header field is not sufficient, we fall back to
the old DRAM scanning routine.
Part of the DRAM might be present and probed by SPL, but not accessible
by the CPU. They're restricted in the main U-Boot binary, when accessing
the DRAM size from SPL header.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
So far we have two users which want to look at the SPL header. We will
get more in the future.
Refactor the existing SPL header checks into a common function, to
simplify reusing the code.
Now that this is easy, add proper version checks to the DT name parsing.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
On Allwinner SoCs we use some free bytes at the beginning of the SPL image
to store various information. We have a version byte to allow updates,
but changing this always requires all tools to be updated as well.
Introduce the concept of semantic versioning [1] to the SPL header:
The major part of the version number only changes on incompatible
updates, a minor number bump indicates backward compatibility.
This patch just documents the major/minor split, adds some comments
to the header file and uses the versioning information for the existing
users.
[1] https://semver.org
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
The Pine A64 Plus/non-Plus model detection code is now built on all
64-bit ARM SoCs, even if the code cannot be triggered when H5/H6 is in
use.
Disable them when the board is Pine A64 by adding a Kconfig option that
is only selected on Pine A64.
On GCC 7.3.1 this makes the size of the function reduces 184 bytes, and
saves a 104 byte strstr() function, then makes SPL on H6 succeed to
build.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add an entry for the warp7_bl33_defconfig target.
This fixes the following warnings:
WARNING: no status info for 'warp7_bl33'
WARNING: no maintainers for 'warp7_bl33'
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Odroid HC2 board is based on Odroid XU4 board, like the Odroid HC1.
The linux kernel does not provide a hc2 DTB so the hc1 DTB is also used
for the Odroid HC2.
Resend because MUA changed whitespace.
Signed-off-by: Dirk Meul <dirk.meul@rwth-aachen.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The DM37 and OMAP35 SOM-LV SOM-LV products both support a NOR
flash part connected to CS2 in addition to the NAND part on CS0.
This patch setups the GPMC timings for the MT28 NOR Flash and
enables the CFI-Flash driver now that the CFI stuff is in Kconfig
Signed-off-by: Adam Ford <aford173@gmail.com>
When booting and CPU is detected from cpuid, we also need an environment
variable that will be used in boot commands to load the proper devicetree.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
In my haste to migrate SPL to DM, I copied the wrong name.
While it really doesn't matter, I'd prefer the name to match
the board, so am335x_mmc0 is now called omap3_logic_mmc0
Signed-off-by: Adam Ford <aford173@gmail.com>
With the new omap_serial driver, this patch uses this instead
from the former ns16550_serial driver. Even though the
omap_serial driver is essentially the same.
Signed-off-by: Adam Ford <aford173@gmail.com>
With the DM_USB working for USB host features, encapsulate the
USB gadget initialization in a precomiler check. If DM is enabled,
we don't need to manually initialize the MUSB driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
The default timings are assumming an OMAP36 / AM37 / DM37, but
the OMAP35 controller is a bit slower, so DDR may operate out of
spec when under stress. This patch checks the processor type and
sets the DDR timings according to processor type.
Fixes: 5ad4212ce0 ("ARM: DTS: Add Logic PD OMAP35/DM37 SOM-LV
and OMAP35 Torpedo")
Signed-off-by: Adam Ford <aford173@gmail.com>
I2C bus 0 was not initialized correctly. There is an offset between i2c
index and the structure number of pad info. So i2c bus 0 can be in an
inconsistent state.
This problem become visible on B{4,6}50v3 with the CPUC HW watchdog enabled.
Sometimes when the CPUC HW watchdog interrupted the boot process, U-Boot was
not able to read VPD from I2C/EEPROM and the system failed to boot up again,
because a device connected to that bus was stuck in data transfer state (from
previous boot attempt) and there was no method to recover (struct
mxc_i2c_bus::idle_bus_fn was not set) courtesy of incorrect initialization.
Signed-off-by: Dan Cimpoca <dan.I.cimpoca@ge.com>
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
The b{4,6}50v3 kernel framebuffer console requires a modeline otherwise
the LVDS panel shows garbage.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
Use Video PLL to provide 65MHz for all displays.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
While using ./scripts/get_maintainer.pl I detect that the Maintainer name
and address for bx50v3 boards are not valid.
The new maintainer for GE bx50v3 products must be Ian Ray.
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
The explicit arch specific build symbol allows to group supported
boards, generalize common config options and it will serve as
a dependency for platform only drivers.
Two related board defconfigs are resynced after the change.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
When referring to the MSTPSR register, it contains the clock
status of SYS, RT, SECURE, and controlling SMSTPCR using this
value has the problem of being affected by the RT and SECURE
status.This patch changes the reference register to SMSTPCR.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
GSX clock force supply code is unnecessary at U-Boot,
because GSX clock control is supported at the kernel driver.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
This code is unnecessary, because these registers are set by the
initial program loader (IPL).
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
This patch adds new zynqmp command "zynqmp tcminit mode" to
initialize TCM. TCM needs to be initialized before accessing
to avoid ECC errors. This new command helps to perform
the same. It also makes tcm_init() as global and uses it for
doing the TCM initialization.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Xilinx is introducing Versal, an adaptive compute acceleration platform
(ACAP), built on 7nm FinFET process technology. Versal ACAPs combine
Scalar Processing Engines, Adaptable Hardware Engines, and Intelligent
Engines with leading-edge memory and interfacing technologies to deliver
powerful heterogeneous acceleration for any application. The Versal AI
Core series has five devices, offering 128 to 400 AI Engines. The series
includes dual-core Arm Cortex™-A72 application processors, dual-core Arm
Cortex-R5 real-time processors, 256KB of on-chip memory with ECC, more
than 1,900 DSP engines optimized for high-precision floating point with
low latency.
The patch is adding necessary infrastructure in place without enabling
platform which is done in separate patch.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Xilinx DLC20 has I2C0 with EEPROM(1KB), UART1, GPIO, SD0 (EMMC 4GB),
USB0 device, ENET0, QSPI (16MB) and DDR(two of 256MB each).
Boards have mix of Winbond/ST QSPIs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add Menlosystems M53 board, based on the M53 SoM.
This board has Ethernet, USB host, USB gadget, UART and LCD on it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
More fixes and improvements for ARC here:
Fixes (this time included for real):
* Take care of global uninitialized variables
They used to be put right after .bss section and were never
zeroed as they should be. Now merged with normal .bss
Improvements:
* Print more verbose CPU info for boards built on real silicon
* Add support for SD-card detection on all ARC boards
* Quite a few fixes for IoT DK
- Support reset by command
- Print of CPU freq on boot
- Link for eFlash etc
So now we may detect MMC/SD-card existence and
instead of completely misleading message on missing card:
------------------------>8-----------------------
Loading Environment from FAT... Card did not respond to voltage select!
------------------------>8-----------------------
we now get very clear one:
------------------------>8-----------------------
Loading Environment from FAT... MMC: no card present
------------------------>8-----------------------
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Since gd->cpu_clk is a global item we may once populate it from .dtb
ans use it then in other places like for printing CPU info etc.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
ARC IDENTITY register only encodes major architecture
type and version while for a particular board/silicon we
may know better which template was used and so we may identify
CPU more precise, which exactly we do here.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Till now we have had cases where we had one phy device per dpmac.
Now, with the upcoming products (LX2160AQDS), we have cases, where there
are sometimes two phy devices for one dpmac. One phy for TX lanes and
one phy for RX lanes. to handle such cases, add the support for multiple
phys in ethernet driver. The ethernet link is up if all the phy devices
connected to one dpmac report link up. also the link capabilities are
limited by the weakest phy device.
i.e. say if there are two phys for one dpmac. one operates at 10G without
autoneg and other operate at 1G with autoneg. Then the ethernet interface
will operate at 1G without autoneg.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Sandbox SPL/TPL support
Various dm-related improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlu9RL4RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYd8gf+NYAGhpiEZZ5vc3DB4Xdn2okgakbbg0QQ
/b0Lr9xQsKgZthK0rvPlH2dXxf+ViAm1iHTy8KBCFi0SHNder48Zui9uTrX0NRq8
pLZGyJPXPYbiyc4pQTEJpTth4iShcphRVio0no4sLpNQqO4aQrialSLa9fnwd9Ra
1l9mF91aaYw6cG+/ejg3UR1LfsDdQ5bjubt0Fw0wGX9UvQOAz5gz5+a17wrz6+Gx
L0gzvyfbuLUhbWB36DXikrL14DAFys2uV9aHJ5zEd53l+F7ZHWsupCO0OtN66cV7
KpPKoYG7vhLqBXKpyrW20T+BPeSyDKmDQE6wbpECmEDOvKzvW67O/w==
=Bfjm
-----END PGP SIGNATURE-----
Merge tag 'dm-9oct18' of git://git.denx.de/u-boot-dm
Test improvements to tidy up output and drop duplicate tests
Sandbox SPL/TPL support
Various dm-related improvements
The interruption support had be removed for ARM architecture and
the function get_timer_masked() is no more used except in some
the timer.c files.
This patch clean each timer.c which implement this function and
remove the associated prototype in u-boot-arm.h
For timer.c, I don't verify if the weak version of get_timer
(in lib/time.c) can be used
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The interruption support had be removed for ARM architecture and
the function udelay_masked() is no more used except in some timer.c
files and have the same content than udelay() or __udelay().
This patch update each timer.c implementing this function and
remove the associated prototype in u-boot-arm.h.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Push generic defines of gpio.h out of mach-davinci to drivers/gpio
now that non-davinci architectures are beginning to use this IP.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Fix calimain build]
Signed-off-by: Tom Rini <trini@konsulko.com>
The uinitrd fixup logic should be executed after the FDT /chosen
node has been properly populated by fdt_initrd()
Signed-off-by: Nicholas Faustini <nicholas.faustini@azcomtech.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This adds platform code for the Khadas VIM2 board based on a
Meson GXM (S912) SoC with the Meson GXM configuration.
This initial submission supports UART, MMC/SDCard and Ethernet.
USB is partially supported.
All the code is from Neil Armstrong! I just rebased the code, do
some cleanup and tested on my board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Loic Devulder <ldevulder@suse.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
There are plenty of existing drivers that have macros like ETH_ALEN
defined in their own source files. Now that we imported the kernel's
if_ether.h to U-Boot we can reduce some duplication.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch add SPL DM support for da8xxevm boards
with SPL serial, SPI drivers supported via platdata.
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850evm
Rather than passing a hardcoded maxsize to the generic get_ram_size()
function use the i.MX 7 specific imx_ddr_size() function, which extracts
the memory size at runtime by reading the DDR controller registers.
This is a purely cosmetic change as the generic get_ram_size() function
already took care of properly automatically detecting 256MB, 512MB or 1GB
modules.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
USB OTG2 port is connected to the USB host connector.
Add support for it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
At present this function uses pixels but it seems more useful for it to
position in terms of characters on the screen. This also matches the
comment to the function. Update this.
Unfortunately there is one user of this function (at91). Have a crack at
fixing this, since I cannot test it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
With there now being four device tree files, and 4 separate
defconfig files, the code necessary to determine which board is
being used is no longer necessary as the corresponding pin-muxing
and board names are determined by the device tree.
Signed-off-by: Adam Ford <aford173@gmail.com>
With the device trees doing most of the work of pin-muxing and
DM doing much of the peripheral initialization, this creates
new defconfig files for each of the Logic PD variants with
proper register settings/pin-muxing.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Update MAINTAINERS entry]
Signed-off-by: Tom Rini <trini@konsulko.com>
The DesignWare ARC IoT Development Kit is a versatile platform
that includes the necessary hardware and software to accelerate
software development and debugging of sensor fusion,
voice recognition and face detection designs.
More information is avaialble here [1] and here [2].
The board is based on real silicon with
ARC EM9D-based Data Fusion IP Subsystem.
It sports a rich set of I/O including
* DW USB OTG
* DW MobileStorage (used for micro SD-card)
* GPIO
* multiple serial interface including DW APB UART
* ADC, PWM and eFlash, SRAM and SPI Flash memory
* Real-Time Clock (RTC)
* Bluetooth module with worldwide regulatory compliance
(FCC, IC, CE, ETSI, TELEC)
* On-board 9-axis sensor (gyro, accelerometer and compass)
Extensible with Arduino, Pmod, mikroBUS connectors and a 2x18
extension header.
One of the most interesting features for developers is built-in
Digilent USB JTAG probe so only micro-USB cable is needed!
[1] https://www.synopsys.com/dw/ipdir.php?ds=arc_iot_development_kit
[2] https://www.synopsys.com/dw/doc.php/ds/cc/iot_dev_kit.pdf
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This adds QEMU RISC-V 'virt' board target support, with the hope of
helping people easily test U-Boot on RISC-V.
The QEMU virt machine models a generic RISC-V virtual machine with
support for the VirtIO standard networking and block storage devices.
It has CLINT, PLIC, 16550A UART devices in addition to VirtIO and
it also uses device-tree to pass configuration information to guest
software. It implements RISC-V privileged architecture spec v1.10.
Both 32-bit and 64-bit builds are supported. Support is pretty much
preliminary, only booting to U-Boot shell with the UART driver on
a single core. Booting Linux is not supported yet.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Since the mach_id is not used by RISC-V, remove it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
The serial# environment variable needs to be
defined so it will be used by fastboot as serial
for the endpoint descriptor.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
LS1043A, LS1046A, LS1088A, LS2088A.
Switch to driver model for SATA on LS1021A and LS1043A.
Add support for LS1012AFRWY rev C board.
Enable SMMU for LS1043A.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XRFI
-----END PGP SIGNATURE-----
Merge tag 'fsl-qoriq-for-v2018.11-rc1' of git://git.denx.de/u-boot-fsl-qoriq
Switch to driver model for eSDHC on Layerscape SoCs including LS1021A,
LS1043A, LS1046A, LS1088A, LS2088A.
Switch to driver model for SATA on LS1021A and LS1043A.
Add support for LS1012AFRWY rev C board.
Enable SMMU for LS1043A.
With DM_MMC working for both SPL and U-Boot, this patch removes
the legacy style of initializing the MMC driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
With the pinctrl function enabled and the device tree setting up
the pins we want to use, this patch removes the manual pinmuxing
except for that which is not done by the device tree and minimal
pins necessary for SPL (like serial, GPMC, and MMC)
Signed-off-by: Adam Ford <aford173@gmail.com>
Call the PDA detection mechanism at boot time so we can have
the pda environment variable ready for use.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Call the PDA detection mechanism at boot time so we can have
the pda environment variable ready for use.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Call the PDA detection mechanism at boot time so we can have
the pda environment variable ready for use.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Call the PDA detection mechanism at boot time so we can have
the pda environment variable ready for use.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Call the PDA detection mechanism at boot time so we can have
the pda environment variable ready for use.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
This adds the support for PDA detection as common code for
Atmel boards.
Using the one wire interface over GPIO , an EEPROM memory is read
and compared to preprogrammed values for PDA screens TM4300, TM7000
and TM7000B.
Once the PDA is detected, an environment variable is set accordingly.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add command to query information from and write text to on-screen
display (OSD) devices.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add device tree for T2080QDS board and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Update board README for device tree usage.
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Reuse the existing ICID setup code done for LS1046A smmu enablement
and add the equivalent setup for LS1043A chips.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The iommu-map property in the fsl-mc node is updated by
valid stream-ids by u-boot. This patch is to fixup this
property for LS208x and LS1088.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1012AFRWY supports three board revisions.
Revision A and B board are collectively identified as revA/B,
Revision C board is identifies as revC.
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
[York S: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Modify the zynqmp_pmufw_version() routine to return PMUFW version so
that it can be reused wherever required. Get PMUFW version from PMU
only once at bootup and later just return stored value.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
On beaglebone black, it can so happen that PHY address
is not latched correctly on reset and board boots with
PHY responding to a different address than that
programmed in device-tree. For example, see this report:
https://groups.google.com/d/msg/beagleboard/9mctrG26Mc8/1FuI_i5KW10J
Workaround this by fixing up device-tree passed to kernel
by using the PHY address detected in hardware.
Beaglebone itself uses only one ethernet port and its DT
currently uses phy_id (obsoleted). But the function has
been written to handle multiple ports and phy_id as well
as phy-handle to make the function more generically useful.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable USB gadget support using DWC2 driver
Populate board_usb_init() to initialize clocks,
phy, reset and data needed for DWC2 IP.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The Gardena Smart-Gateway boards have a MT7688 SoC with 128 MiB of RAM
and 8 MiB of flash (SPI NOR) and additional 128MiB SPI NAND storage.
This patch also includes 2 targets. One is the target that can be
programmed into the SPI NOR flash and a 2nd target "xxx-ram" is
added to support loading and booting via an already running U-Boot
version. This allows easy development and testing without the
need to flash the image each time.
Signed-off-by: Stefan Roese <sr@denx.de>
[fixed and regenerated defconfig files]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The LinkIt Smart 7688 modules have a MT7688 SoC with 128 MiB of RAM
and 32 MiB of flash (SPI NOR).
This patch also includes 2 targets. One is the target that can be
programmed into the SPI NOR flash and a 2nd target "xxx-ram" is
added to support loading and booting via an already running U-Boot
version. This allows easy development and testing without the
need to flash the image each time.
Signed-off-by: Stefan Roese <sr@denx.de>
[fixed and regenerated defconfig files]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
If PCIe Mox module is connected we want to have PCIe node enabled
in U-Boot's device tree.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
The macro name CONFIG_WDT_ARMADA_3720 is called CONFIG_WDT_ARMADA_37XX
instead. Fix this so that watchdog really is enabled in board_init.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
This adds a new defconfig which pre-selects the PICO-Hobbit baseboard
allowing a completely non-interactive boot process.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This adds a new defconfig which pre-selects the PICO-Pi baseboard
allowing a completely non-interactive boot process.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Drop the macro as it is defined in sh7723.h already.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Falcon mode allows the SPL to load and jump directly to the kernel,
without loading U-Boot proper.
Add detailed step by step on how to use Falcon mode on pico-imx6ul.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Falcon mode boots the kernel directly from SPL, without loading
the full U-Boot.
As pico-imx6ul does not have a GPIO for selecting Falcon versus normal
mode, enter in Falcon mode when the customer selects the
CONFIG_SPL_OS_BOOT option in menuconfig.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The serverip part is provided from DHCP server with
'option root-path "192.168.3.1:/srv/tftp/rootfs";' parameter in dhcpd.conf
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The quotes around ${bootargs} were missing as we elaborate those variables
twice - once when we "setenv" the command and secondly when we "run" it.
Without quotes we have just empty string in the second call.
Moreover there is an issue with line breaks - as the original commands
got truncated.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The 'dhcp' command is more versatile as it allows working with the DHCP
server to obtain serverip, ipaddress and other network parameters.
The configuration necessary to obtain the serverip (dhcpd.conf):
option option-150 code 150 = ip-address;
and in the subnet definition:
option option-150 192.168.X.Y;
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The 'rootpath' can be provided by DHCP server. Removing this line prevents
from overwriting it.
To do that on the DHCP server side (isc-dhcp-server) modify dhcpd.conf
and add 'option root-path "192.168.X.Y:/srv/tftp/rootfs";'
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The new config skips the boot menu which asks which board is in
use. This is useful to allow direct booting of image without user
iteration.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Update the README file to take into accound the switch to SPL.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Currently only the module with 256MB of RAM is supported.
Add support for the 512MB of RAM variant as well.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
There are two versions of imx6ul pico SOMs: one with 256MB and another
one with 512MB of RAM.
Convert to SPL so that both versions can be supported. This patch
doesn't rework the clock initialization to avoid changing the behavior
in this same patch, so it will be cleaned up in future.
Currently only the 256MB is tested/supported.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
DM_I2C_COMPAT is somehow being enabled outside of Kconfig, so
this explicitly undefines it in the header file, and brackets
the I2C initialization around an #ifdef to not manually
initialize the I2C controller when the DM_I2C is enabled.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
With DM_MMC now available, this patch enables DM_MMC for the
omapl138_lcdk in U-Boot and keeps the older style for SPL.
Signed-off-by: Peter Howard <phoward@gme.net.au>
Signed-off-by: Adam Ford <aford173@gmail.com>
The OF_CONTROL and OF_PLATDATA are not really useful without DM.
This patch supports DM_SPL, but it requires manual references
both Serial and MMC.
Signed-off-by: Adam Ford <aford173@gmail.com>
The DA850-EVM supports booting from NAND when used with the
UI expander board. da850evm_nand will create an ais file
that can be burned to NAND and booted while storing the env in
NAND along with some partitions tables for storing kernel,
dtb and rootfs in NAND.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add initial support for AM654 based EVM running on A53. Enable
4GB of DDR available on the EVM so that kernel DTB file
can be updated accordingly.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[Andreas: Added 4GB ddr support]
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
This patch enables DM_SERIAL for the pandora board. Verified that
the default kernel can still be booted with this.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Add support for loading U-Boot on the Broadcom 7260 SoC. This port
assumes Broadcom's BOLT bootloader is acting as the second stage
bootloader, and U-Boot is acting as the third stage bootloader, loaded
as an ELF program by BOLT.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
In int-ll64.h, we always use the following typedefs:
typedef unsigned int u32;
typedef unsigned long uintptr_t;
typedef unsigned long long u64;
This does not need to match to the compiler's <inttypes.h>.
Do not include it.
The use of PRI* makes the code super-ugly. You can simply use
"l" for printing uintptr_t, "ll" for u64, and no modifier for u32.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Update the README file to take into accound the switch to SPL.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
QEMU 3.0 introduced additional memory-mapped regions for PCI-E ECAM and
MMIO. Thus we need to add them to our MMU map or U-Boot will crash with
a Synchronous Abort during PCI-E probing when it tries to access the
unmapped ECAM memory area.
Reported-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Tested-by: Jonathan Gray <jsg@jsg.id.au>
Without this patch the Ethernet PHY on the p212 board does not get
fully configured.
When this happens Ethernet does not function.
The similar libretech-cc and khadas-vim boards have this code already.
That's why the Ethernet on these boards do work.
Signed-off-by: Jasper Kcoding <jasperkcoding@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Add an entry for mx7dsabresd_qspi_defconfig to avoid the following
warnings:
WARNING: no status info for 'mx7dsabresd_qspi'
WARNING: no maintainers for 'mx7dsabresd_qspi'
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
This commit adds support for the Toradex Colibri iMX7D 1GB Computer
on Module. The module is very similar to the Colibri iMX7D 512MB
but uses eMMC instead of raw NAND. This patch introduces a new
board specific Kconfig symbol to select between the two flash
options.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Convert the codes and configurations to enable DM drivers in u-boot for
modules: i2c, PMIC, regulator, USB, Ethernet, SD/MMC, GPIO and QSPI
This patch does not change SPL, so it still uses non-DM driver for
UART, GPIO and SD/MMC.
Signed-off-by: Ye Li <ye.li@nxp.com>
On iMX7D SabreSD board, the QSPI has pins conflict with EPDC (default).
To use QSPI, users have to rework the board (de-populate R388-R391, R396-R399
populate R392-R395, R299, R300). So we add new DTS file and new defconfig
dedicated for QSPI.
Other changes to support the DM QSPI:
- Add QSPI node and alias spi0.
- Modify spi4 (spi-gpio) node and add alias spi5 for it to avoid req
conflict
- Add EPDC node in imx7d.dtsi and disable it in imx7d-sdb-qspi.dts to
align with kernel and also present the conflict.
- Add -u-boot.dtsi to modify compatible string of mx25l51245g@0 to
"spi-flash"
- Remove iomux settings of qspi in board codes which is not needed
for DM driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
To support DM QSPI driver:
- Add -u-boot.dtsi to modify n25q256a@0 and n25q256a@1 compatible string
to "spi-flash" and add "num-cs" property.
- Enable DM SPI and DM SPI FLASH configurations
- Remove iomux settings of qspi1 in board codes which is not needed
for DM driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
To support DM QSPI driver
- Add spi0 and spi1 alias for qspi1 and qspi2.
- Add -u-boot.dtsi to modify n25q256a@0 and n25q256a@1 compatible string
to "spi-flash" and add "num-cs" property.
- Enable DM SPI/QSPI relavent configurations
- Remove iomux settings of qspi2 in board codes which is not needed
for DM driver.
- Add sf default settings. So running "sf probe" can detect the flash
Signed-off-by: Ye Li <ye.li@nxp.com>
Update the HiKey board instructions based on the latest source
available. These instructions are derived from the ATF platform doc.
While updating the instructions, some comments on ATF issue has been
removed since it is fixed in latest ATF source.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The reset is already handled by the designware driver using
information from device tree.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
When MUSB is operating in peripheral mode, probe registering
musb core using musb_register which intern return int value
for validation. so there is no scope to preserve struct musb
pointer but the same can be used in .remove musb_stop.
So fix this by return musb_register with struct musb pointer.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Purna Chandra Mandal <purna.mandal@microchip.com>
Tested-by: Chen-Yu Tsai <wens@csie.org> # A33-OlinuXino
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
variables buf from board_mmc_init, and ret from misc_init_r
were unused on the functions, so remove it.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The da850evm with its UI expander board can boot XIP boot from
NOR flash. This adds the instructions to the readme. file.
Signed-off-by: Adam Ford <aford173@gmail.com>
Currently building U-Boot as the coreboot payload requires user
to change the build configuration for a specific board during
menuconfig process. This uses the board's native device tree
to configure the hardware. For example, the device tree provides
PCI address range for the PCI host controller and U-Boot will
re-program all PCI devices' BAR to be within this range. In order
to make sure we don't mess up the hardware, we should guarantee
the range matches what coreboot programs the chipset.
But we really should make the coreboot payload support easier.
Just like EFI payload, we can create a generic coreboot payload
for all x86 boards as well. The payload is configured to include
as many generic drivers as possible. All stuff that touches low
level initialization are not allowed as such is the coreboot's
responsibility. Platform specific drivers (like gpio, spi, etc)
are not included.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Change the way MAC address fixup is done:
1. Stop using LK handed device-tree and calculate
the MAC address our own.
2. Allow overriding the generated MACS with environment variables:
"wlanaddr" and "btaddr".
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Commit 1473b12ad0 ("lib: fdtdec: Update ram_base to store ram start
adddress") brings regression on STM32F7 which can't boot.
Use fdtdec_setup_mem_size_base() to setup memory base and size.
Use fdtdec_setup_memory_banksize() to setup memory bank base and size.
Reported-by: Mark Olsson <mark@markolsson.se>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Cc: Mark Olsson <mark@markolsson.se>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Use gd->bd->bi_dram[0].start initialized from DT instead of using
hardcoded CONFIG_SYS_SDRAM_BASE from config file.
Remove unused CONFIG_SYS_RAM_BASE and CONFIG_SYS_SDRAM_BASE defines.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Move ns_dev[] from header file to C file to avoid compiling warning
when header file is included by others.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: rewrite commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Add infrastructure for ICID setup and device tree fixup on ARM
platforms. This include basic ICID setup for several devices.
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Initialize the led with the default state defined in device tree
in board_init and solve issue with test for led default state.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Initialize the led with the default state defined in device tree.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add an initial MAINTAINERS file based on author of the code.
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This add the initial support of the broadcom reference
board bcm968380gerg with a bcm68380 SoC.
This board has 512 MB of RAM, 128 MB of flash (nand),
2 USB port, 1 UART, 4 ethernet ports and BCM43217 (wifi).
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The only platform left for the AU1x00 SoCs was the pb1x00 platform, an
apparent clone of the dbau1x00 platform. As pb1x00 had no listed
maintainer I am assuming that it is also orphaned. Remove this platform
and then remove the unused SoC support.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This platform has been marked as orphan since June of 2016 and should
have been removed some time ago. Do so now.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add command "boot_bank X" to switch the boot bank to either 1 or 2.
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This is a series of line cards for Allied Telesis's SBx8100 chassis
switch. The CPU block is common to the SBx81GP24 and SBx81GT24 cards
cards collectively referred to as SBx81LIFXCAT in u-boot.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Move the gdsys Controlcenter DC specific build time kwbimage.cfg
generation code into the mach-mvebu/ directory to be shared by all 32bit
mvebu platforms.
Remove board specific kwbimage.cfg files, and use the generated one
instead. These files are all identical, with two exceptions. Clearfog
and Helios4 use the sdio boot device, whereas all others use spi. Update
the defconfigs for the exceptional boards to generate the same
kwbimage.cfg as before.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Use MVEBU_SPL_BOOT_DEVICE_* to select between SPI and MMC, instead of
board specific symbols. This commit enables the boot device selection
menu to all mvebu platforms, but it is only effective on Turris Omnia
and gdsys Controlcenter DC platforms. A following commit will enable
boot selection for other platforms.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Use generic mvebu Kconfig symbols like all other mvebu boards.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
u-boot-spl.bin and u-boot-spl-dtb.bin are identical when building the
turris_omnia_defconfig. This commit makes Turris Omnia consistent with
all other mvebu boards.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Avnet Ultra96 is rebranded Xilinx zcu100 revC/D. Add new defconfig files
and point to origin internal board name.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This issue is reported by kconfiglib:
warning: style: quotes recommended around default value for string
symbol XILINX_MICROBLAZE0_HW_VER (defined at
board/xilinx/microblaze-generic/Kconfig:37)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This commit adjusts the autoboot.cmd file to use ${mmcbootdev} instead of
hardcoded value 0.
This is necessary to allow booting this board from the SD card.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The "Beaglebone Enhanced" by Sancloud is based on the Beaglebone Black,
but with the following differences:
* Gigabit capable PHY
* Extra USB hub, optional i2c control
* lps3331ap barometer connected over i2c
* MPU6050 6 axis MEMS accelerometer/gyro connected over i2c
* 1GiB DDR3 RAM
* RTL8723 Wifi/Bluetooth connected over USB
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Reviewed-by: Tom Rini <trini@konsulko.com>
That's a set of prety minor changes and fixes for ARC.
Among them:
* Improvement in CREG GPIO driver used on ARC dev boards
that allow us to re-use the driver for SPI's chip select
* Enable SPI-flsh on AXS10x boards which allows to update
U-Boot binary that gets loaded by boot-ROM
* Fix accommodating always utilized unaligned access by
GCC for ARC starting from 8.1.0
After talking with Albert, mark these boards as orphaned as he no longer
has one.
Cc: Albert ARIBAUD <albert-u-boot@aribaud.net>
Cc: Vagrant Cascadian <vagrant@debian.org>
Cc: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Update the MAINTAINERS file to list Otavio Salvador as the maintainer
for this board.
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Tom Rini <trini@konsulko.com>
OrangePi One Plus is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211
- USB 2.0 Host, OTG
- HDMI port
- 5V/2A DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Pine H64 is a SBC with Allwinner H6 SoC produced by Pine64. It features
1GiB/2GiB/4GiB(3GiB usable) DRAM, two USB 2.0 ports, one USB 3.0 port
and a mPCIE slot.
Add support for it.
The device tree is from Linux next-20180720.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The Allwinner H6 SoC has 3 MMC controllers like the ones in A64, with
the MMC2 come with the capability to do crypto by EMCE.
Add MMC support for H6. EMCE support is not added yet.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
H6 has different SRAM A2 address, so the ATF load address is also
different.
Add judgment code to sunxi 64-bit FIT generation script. It will judge
the SoC by the device tree's name.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Since U-Boot tools are being built anyways it's much nicer
to use them instead of relying on some of them bein installed
on build host (which might easily not be the case).
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
AXS10x boards have preloader that reads SPI flash pages and searches
special image header to fetch and load binary.
Add tool, make target (bsp-generate) to generate
update script and u-boot binary image with header for preloader.
Also add script to default environment to apply updates.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Highlights this time:
- Many small fixes to improve spec compatibility (found by SCT)
- Almost enough to run with sandbox target
- GetTime() improvements
- Enable EFI_LOADER and HYP entry on ARMv7 with NONSEC=y
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=ePTT
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-07-25
Highlights this time:
- Many small fixes to improve spec compatibility (found by SCT)
- Almost enough to run with sandbox target
- GetTime() improvements
- Enable EFI_LOADER and HYP entry on ARMv7 with NONSEC=y
A new defconfig is introduced to support SPL boot from QSPI NOR
flash. This is to support falcon mode for faster booting into
Linux.
Signed-off-by: York Sun <york.sun@nxp.com>
This patch updates the copyright claim for the issues reported by
legal review.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Some times gcc may generate data that is then used within code that may
be part of an efi runtime section. That data could be jump tables,
constants or strings.
In order to make sure we catch these, we need to ensure that gcc emits
them into a section that we can relocate together with all the other
efi runtime bits. This only works if the -ffunction-sections and
-fdata-sections flags are passed and the efi runtime functions are
in a section that starts with ".text".
Up to now we had all efi runtime bits in sections that did not
interfere with the normal section naming scheme, but this forces
us to do so. Hence we need to move the efi_loader text/data/rodata
sections before the global *(.text*) catch-all section.
With this patch in place, we should hopefully have an easier time
to extend the efi runtime functionality in the future.
Signed-off-by: Alexander Graf <agraf@suse.de>
[agraf: Fix x86_64 breakage]
Add 'const' (also 'static' in some places) to struct node_info
arrays to save memory footprint.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The previous e-mail pointing to Vaibhav Hiremath <hvaibhav@ti.com>
is bouncing and has for some time. This updates it to myself and I
work for Logic PD the manufacturer of the AM3517-SOM and EVM
Signed-off-by: Adam Ford <aford173@gmail.com>
The m5253evbe board has been marked as orphan since June of 2014 and
should have been dropped a while ago. Do so now.
Signed-off-by: Tom Rini <trini@konsulko.com>
Since the vast majority of i.MX6 boards are migrating to SPL,
this patch converts im6q_logic to SPL and enables the SDP for
loading SPL and u-boot.img over USB. The Falcon mode only
supports NAND flash as of now due to limited space/RAM, but
all i.MX6D/Q SOM's from Logic PD have internal NAND from which
to boot.
Signed-off-by: Adam Ford <aford173@gmail.com>
This reverts commit a637fe6f27.
The DDR DRAM calibration was enhanced by write leveling correction code.
It can be used with T-topology now.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
Our default config already has the secure mode supported, so the
manual step is not required anymore.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The DFU allows a more user friendly use as the details where the
bootloader is installed are abstracted.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The addrmap5 value is the same for the 512MB and 1GB variants,
so there is no need to override it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Falcon mode boots the kernel directly from SPL, without loading
the full U-Boot.
As pico-imx7d does not have a GPIO for selecting Falcon versus
normal mode, enter in Falcon mode when the customer selects
the CONFIG_SPL_OS_BOOT option in menuconfig.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Convert pico-imx7d to SPL support.
There are two variants of pico-imx7d SOMs:
- One with 512MB of RAM
- One with 1GB of RAM
The 512MB module contains two Hynix H5TC2G63GFR-PBA.
The 1GB module contains two Hynix H5TC4G63GFR-PBA.
The RAM size is determined in runtime by reading GPIO1_12.
While at it, also add USB Serial Download mode support as it
is very helpful for loading SPL and u-boot.img via imx_usb_loader.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This makes sure that all Colibri iMX7 modules work with the
same timing. The changes are:
- Disable ODT on read (JEDEC standard JESD79-3F says in chapter
5.2.3 ODT during Reads: "As the DDR3 SDRAM can not terminate
and drive at the same time, RTT must be disabled at least half
a clock cycle..." and also MX7D SABRESD is disabling it)
This alone fixed memory issues for two Colibri iMX7 1GB modules
which showed issues before
- Make sure tRFC(min) is at least 260ns
- Make sure tRC is >50.625ns
- tRP needs to be >13.125ns, we can lower from 18.75ns to 15ns
- tFAW is not relevant, leave at reset
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Device trees from vanilla Linux do not specify a i.MX 7 specific
compatible string. Make sure to set partitions also when booting
upstream Linux.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Fix an invalid usage of the gpr_init function for the imx6ul
architecture
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
i.MX7 does not support BMODE due to the erratum e10574 ("Watchdog:
A watchdog timeout or software trigger will not reset the SOC"), so
remove its support.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Previously we had just made broad assumptions with which of our
boards had an eMMC or not even though this is a manufacturing time
assembly option. This takes the guessing away and actually checks for
the existence of an eMMC and sets up the has_emmc environment variable.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
The HB2 boards as well as rev 1.5 soms support eMMC
booting as well as SDHC. Add the infrastructure to support
booting these devices.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
