Add RAM auto-sizing, without this change memory size for all SKU is set
to 8GB and the system will crash on SKU with less memory as soon as the
non existent memory addresses are accessed.
Fixes: 2bc2f817ce ("board: toradex: add verdin imx8m plus support")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
With this call the following attributes get set to the device-tree
and are then accessible from linux in /proc/device-tree/
serial-number: The serial number that is stored in config-block
toradex,board-rev: The version of the module (e.g. V1.1A)
toradex,product-id: The SKU number of the module runnin
Fixes: commit 2bc2f817ce ("board: toradex: add verdin imx8m plus support")
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
With this call the following attributes get set to the device-tree
and are then accessible from linux in /proc/device-tree/
serial-number: The serial number that is stored in config-block
toradex,board-rev: The version of the module (e.g. V1.1A)
toradex,product-id: The SKU number of the module running
Fixes: commit 14d5aeff77 ("board: toradex: Add Verdin iMX8M Mini support")
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Enable the I2C bus and set a env variable for the reset GPIO of the touch
controller. This allows us to probe the panel in a script.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This adds support for the Kontron Electronics SoM SL i.MX8MM OSM-S
and the matching baseboard BL i.MX8MM OSM-S.
The SoM hardware complies to the Open Standard Module (OSM) 1.0
specification, size S (https://sget.org/standards/osm).
The existing board configuration for the non-OSM SoM is reused and
allows to detect the SoM variant at runtime.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Refactor the code a bit without any functional changes.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This adjusts the names of the boards and SoMs to the official naming
used by Kontron marketing. These changes also affect devicetree
names and compatibles. The same changes have been submitted to the
Linux kernel.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This sets an env variable 'som_type' from the board code. It can
later be used by environment scripts, e. g. to select the proper
devicetree for the board.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
These parameters are needed for stable performance on new hardware
with Nanya LPDDR4 chips.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The new stable configuration is missing the 100mt setpoint, remove
it before updating the config to make sure the changes are separated
cleanly.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Fix the spaces and alignment for easier tracking of changes and comparing
with configs generated by the tools.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Move the environment from the board header to a separate text file
and also drop those variables that are already set in env_default.h
from the Kconfig options.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
In case we boot from SD card or eMMC, we also want to load
the environment from the according boot device.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Nowadays detecting the SPI NOR as boot device from the ROMAPI is
fixed and works even if the SPI NOR is used as fallback boot device.
Therefore we don't need this workaround anymore.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The display isn't and won't be used in U-Boot. Also the display setup
is not yet supported in mainline Linux, so even for cases where the
U-Boot devicetree is passed to the kernel there is currently no use
for this configuration.
Selecting the proper configuration in the kernel FIT image automatically
depending on the detected hardware can be handled by a script in the
environment.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Move the environment from the board header to a separate text file
and also drop those variables that are already set in env_default.h
from the Kconfig options or are not needed anymore.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Instead of checking both, SPI NOR and MMC for loading U-Boot proper
and the environment, implement a way to detect the actual boot
device even if the BootROM doesn't report it and we can't rely
solely on the fuse settings, as by default we use MMC as primary
boot device and boot from SPI NOR via the secondary fallback device
(EEPROM Recovery Mode).
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Beside some rather unexciting sync of the DTs from the kernel tree, and
some Kconfig cleanup, there are some improvements for the ARMv5 Allwinner
family, to support boards with the F1C200s (64MB DRAM) better. We will
get actual board support as soon as the DTs have passed the Linux review
process.
There is also support for the X96 Mate TV Box, featuring the H616 SoC and
a full 4GB of DRAM.
Also we found the secret to enable SPI booting on the H616 (pin PC5 must
be pulled to GND), so the SPI boot support patch is now good to go.
Passed the gitlab CI, plus briefly tested on Pine64-LTS, LicheePi Nano,
X96 Mate and OrangePi Zero.
Check firmware_fdt_addr header to see if it
is a valid fdt blob.
Signed-off-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Since OpenSBI commit bf3ef53bb7f5 ("firmware: Enable FW_PIC by default"),
OpenSBI runs directly at the load address without any code movement.
This causes the SPL version of QEMU 'virt' U-Boot does not boot Linux
kernel anymore. In that case, OpenSBI is loaded and runs at 0x81000000,
and it creates a 512KiB PMP window from that address. When booting
the Linux kernel, moving kernel to its linking address 0x80200000
overlaps the PMP window, and a PMP access failure is raised.
Update SPL_OPENSBI_LOAD_ADDR to load OpenSBI to a safe address.
Reported-by: Yangjie Zhang <pyjmstr@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Yangjie Zhang <pyjmstr@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The X96 Mate TV box is a TV box with the Allwinner H616 SoC. It is
available with up to 4GB of DRAM and 64GB eMMC.
The DRAM chips require a different configuration when compared to the
OrangePi Zero2, we must not use read/write training and write leveling.
Add a defconfig for the box, so that we can easily build U-Boot for it.
We synced the .dts file already from the kernel tree.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Now that a single binary containing TPL/SPL correctly formatted for SPI
flashes and U-Boot proper, can be generated by binman, let's do it.
Also update the documentation to tell the user to use this newly
generated file instead of manually generating and flashing the binaries.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The offset of the SPL payload on Puma is different than for other
Rockchip devices in that it is stored at offset 256K instead of much
further away in the MMC.
Flashing one binary instead of two at different offsets is much more
user friendly so let's migrate to it by modifying the offset in the Puma
specific Device Tree.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Depending on the toolchain used to compile the SPL for Puma RK3399-Q7
module, the board does not boot because the resulting binary is too big
to fit in SRAM.
Let's add a TPL so that there's no need to fiddle with or hack the
defconfig to have a working bootloader.
This follows what's been done for the majority of other RK3399-based
boards.
See the original commit for the first migrations:
bdc0008011 "rockchip: rk3399: update defconfig for TPL"
Unfortunately, the offset in SPI-NOR for U-Boot proper needs to be
modified, since the move from SPL to TPL+SPL for idbloader.img (and the
"only the first 2KB per 4KB blocks are written" "hack" for rkspi format)
increased the size above 256KB. Let's move it to 512KB to, hopefully, be
safe.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Chances are when one boots U-Boot proper from a given storage medium,
they want the same medium to be used to load and store the environment.
This basically allows to have completely separate U-Boot (TPL/SPL/U-Boot
proper/environment) per storage medium which is convenient when working
with recovery from SD-Card as one would just need to insert a properly
configured SD-Card into the device to have access to their whole debug
setup.
No fallback mechanism is provided as to not dirty other storage medium
environment by mistake. However, since arch_env_get_location() is called
by env_init() which is part of the pre-relocation process, a valid,
non-ENVL_UNKNOWN, value shall be returned otherwise the relocation fails
with the following message:
initcall sequence 00000000002866c0 failed at call 0000000000256b34 (err=-19)
This valid, non-ENVL_UNKNOWN, value is ENVL_NOWHERE which requires to
always select CONFIG_ENV_IS_NOWHERE otherwise this work-around does not
work.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Automatically detect which MMC device (SD-Card or eMMC) was used to load
U-Boot proper and load the environment from that MMC device instead of
a hardcoded one.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
CONFIG_ENV_OFFSET is set in the defconfig to a different value already
so this isn't used. Let's remove it as to not confuse users.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
distroboot should try first on the same MMC medium as the one the SPL
loaded U-Boot proper from. This was the case when the introducing commit
was merged because the default order was eMMC first and then SD card.
The check was therefore made only on whether we booted from SD card,
because otherwise the order was the expected one.
However, in commit b212ad24a6 ("rockchip: Fix MMC boot order"), the
order was swapped. Meaning our simple check is now useless.
Let's fix that by accounting for all scenarii: default boot_targets has
mmc0 first but booting from SD Card, mmc1 first but booting from eMMC.
Fixes: b212ad24a6 ("rockchip: Fix MMC boot order")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Specification
- Rockchip RK3399
- LPDDR3 4GB
- TF sd scard slot
- eMMC
- AP6255 for WiFi + BT
- Gigabit ethernet
- HDMI out
- 40 pin header
- USB 2.0 x 2
- USB 3.0 x 1
- USB 3.0 Type-C x 1 work in otg mode
- 12V DC Power supply
The dts file is sync from linux-next[0].
[0]:https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/tree/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
Signed-off-by: Andy Yan <andyshrk@163.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
CONFIG_SERIAL_TAG is not selectable for ARM64 machines. While
get_board_serial is weakly defined if ENV_VARS_UBOOT_RUNTIME_CONFIG is
defined, it is only called when CONFIG_SUPPORT_PASSING_ATAGS is defined,
which also is not selectable for ARM64 machines. Therefore this is dead
code so let's remove it.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The phycore_rk3288 board has a SPL size problem,
so remove phycore_init() function to stay within the limits.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
For some unknown reason GNU assembler version 2.31.1 (arm-linux-gnueabi-as
from Debian Buster) cannot compile following code from located in file
board/nokia/rx51/lowlevel_init.S:
kernoffs:
.word KERNEL_OFFSET - (. - CONFIG_SYS_TEXT_BASE)
when CONFIG_SYS_TEXT_BASE is set to 0x80008000. It throws strange compile
error which is even without line number:
AS board/nokia/rx51/lowlevel_init.o
{standard input}: Assembler messages:
{standard input}: Error: attempt to get value of unresolved symbol `L0'
make[2]: *** [scripts/Makefile.build:293: board/nokia/rx51/lowlevel_init.o] Error 1
I have no idea about this error and my experiments showed that ARM GNU
assembler is happy with negation of that number. So changing code to:
kernoffs:
.word . - CONFIG_SYS_TEXT_BASE - KERNEL_OFFSET
and then replacing mathematical addition by substraction of "kernoffs"
value (so calculation of address does not change) compiles assembler file
without any error now.
There should be not any functional change.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Support VBE OS requests / fixups
Minor error-handling tweaks to bootm command
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmNOjr4RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreakFQf/bLTFMI8noOMa9d6Yo1RTSOa9wNiomgzC
JGY7g8i7b6cARwQ+QuSncnO/EOpwjzBLWkohUK3UAktJu2LURBPJFR4qeP01F7iz
4Mn3ikYlr3vRxAPeckN7l1aqSWrY/tEXbUdXLxSn+COzjxCQG5aBU1jd/tVBqIAk
XgZ0NGVHOQe8XOPNxDP9+EYHw4kmqMSdWZmpkb1w+Jh5AIYMMDgn1ktiNmnWXllx
LM89JxR8FMUJzFP9XBRtYemje55tAUPlENthRip9Zj9touEBbBKjV5eY8YsjpMMU
Vt5rK33vKWE4mdNBjRmOoe9xkUv/pRclpaGUFBNswf2LGw7/lsHd2A==
=3P/S
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-18oct22' of https://source.denx.de/u-boot/custodians/u-boot-dm
Update uclass iterators to work better when devices fail to probe
Support VBE OS requests / fixups
Minor error-handling tweaks to bootm command
Fix the compilation issue when CONFIG_DEBUG_UART is activated
drivers/serial/serial_stm32.o: in function `debug_uart_init':
drivers/serial/serial_stm32.c:291: undefined reference to \
`board_debug_uart_init'
The board_debug_uart_init is needed for SPL boot, called in
cpu.c::mach_cpu_init(); it is defined in board/st/stm32mp1/spl.c.
But with the removal #ifdefs patch, the function debug_uart_init() is
always compiled even if not present in the final U-Boot image.
This patch adds a file to provided this function when DEBUG_UART and SPL
are activated.
Fixes: c8b2eef52b ("stm32mp15: tidy up #ifdefs in cpu.c")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add DT for DHCOR Testbench board, which is a testbench for testing of
DHCOR SoM during manufacturing. This is effectively a trimmed down
version of AV96 board with CSI-2 bridge, HDMI bridge, WiFi, Audio and
LEDs removed and used as GPIOs instead. Furthermore, the PMIC Buck3
is always configured from PMIC NVM to cater for both 1V8 and 3V3 SoM
variant.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
In case the regulator-always-on is present in regulator DT node,
the regulator is always reconfigured to the voltage set in DT on
probe, even if regulator_set_value() has been called before. Drop
the property from AV96 U-Boot DT and enable the regulator manually
in code, as the board already reconfigures the Buck3 regulator in
code per PMIC NVM content instead.
Fixes: 0adf10a87b ("ARM: dts: stm32: Configure Buck3 voltage per PMIC NVM on Avenger96")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
In a later patch sysinfo_get will be changed to return the device in cae
of an error. Set sysinfo to NULL on error to preserve previous behavior.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
There are a couple users of uclass_next_device return value that get the
first device by other means and use uclass_next_device assuming the
following device in the uclass is related to the first one.
Use uclass_next_device_err because the return value from
uclass_next_device will be removed in a later patch.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is a number of users that use uclass_first_device to access the
first and (assumed) only device in uclass.
Some check the return value of uclass_first_device and also that a
device was returned which is exactly what uclass_first_device_err does.
Some are not checking that a device was returned and can potentially
crash if no device exists in the uclass. Finally there is one that
returns NULL on error either way.
Convert all of these to use uclass_first_device_err instead, the return
value will be removed from uclass_first_device in a later patch.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The LS1043ARDB rev v7.0 board replace nand device MT29F4G08ABBDAH4-AITX:D
with MT29F4G08ABBFAH4-AIT:F. Reflecting this change in board_fix_fdt().
CPLD V3.0 is needed for nandboot as the nand device changed.
A new macro CPLD_CFG_RCW_SRC_NAND_4K(4Kpage) is added to distinguish from
CPLD_CFG_RCW_SRC_NAND(2Kpage) to support nandboot on rev v7.0 board.
Signed-off-by: Wei Lu <w.lu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Space key is indicated by two different bits. Some HW models indicate press
of space key only by the first bit. Qemu indicates it by both bits at the
same time, which is currently interpreted by u-boot as double key press.
Fix this issue by setting first bit when only second is set (to support HW
models which indicate press only by second bit) and always clearing second
bit before processing to not report double space key press.
Signed-off-by: Pali Rohár <pali@kernel.org>
Before this patch you could see in the log:
U-Boot SPL 2022.10-rc5 (Sep 29 2022 - 15:29:27 +0200)
PMUFW: v1.1
Loading new PMUFW cfg obj (32 bytes)
PMUFW: No permission to change config object
Loading new PMUFW cfg obj (2032 bytes)
where it is visible that permission is check before sending PMUFW
configuration (big size).
When this patch is applied it is visible that order is correct.
U-Boot SPL 2022.10-rc5 (Sep 29 2022 - 15:47:08 +0200)
Loading new PMUFW cfg obj (2032 bytes)
PMUFW: v1.1
Loading new PMUFW cfg obj (32 bytes)
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/a0bf4f46d670023da4f848790eece6fff22090c2.1664962765.git.michal.simek@amd.com
Compiling with GCC-12 leads to an error:
+board/xilinx/common/board.c:479:37: error: the comparison will always
evaluate as 'true' for the address of 'mac_addr' will never be NULL
[-Werror=address]
+ 479 | if (!desc->mac_addr[i])
+ | ^
Remove the redundant check.
Fixes: a03b594738 ("xilinx: board: Add support for additional card detection")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Link: https://lore.kernel.org/r/20221008091317.52838-1-heinrich.schuchardt@canonical.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
In function ‘set_dfu_alt_info’ a comparison of a u8 value against
0 is done. Since it is always false, change the signature of this
function to use an `int` instead, which match the type used in caller:
`multi_boot()`.
Fix the following warning triggered with W=1:
board/xilinx/zynqmp/zynqmp.c:651:23:
warning: comparison is always false due to limited range of data type
[-Wtype-limits]
651 | if (multiboot < 0)
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20221004055254.26246-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
cpu-info.c defines print_cpuinfo(), but neglected to
include its declaration, causing the following sparse and
compile time warnings:
board/xilinx/common/cpu-info.c:10:5:
warning: no previous prototype for 'print_cpuinfo'
[-Wmissing-prototypes]
Include init.h, which includes the missing declaration.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20221004055053.26047-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
dram_init() can't modify global/static variables, so
move the mem_map setup later when bss is available.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
These boards are out of maintenance and can be removed.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This is not needed and we should avoid typedefs. Use the struct instead
and rename it to indicate that it really is a legacy struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
The situation is similar to commit bf6376642f ("board: ti: common:
board_detect: Fix EEPROM read quirk"). This is seen on a variant of
eeproms seen on some BeagleBone-AI64 which now has a mix of both 1 byte
addressing and 2 byte addressing eeproms.
Unlike the am335x (ti_i2c_eeprom_am_get) and dra7
(ti_i2c_eeprom_dra7_get) which use constant data structure which allows
us to do a complete read of the data, the
am6(ti_i2c_eeprom_am6_get) eeprom parse operation is dynamic.
This removes the option of being able to read the complete eeprom data
in one single shot.
Fortunately, on the I2C bus, we do see the following behavior: In 1
byte mode, if we attempt to read the first header data yet again, the
misbehaving 2 byte addressing device acts in constant addressing mode
which results in the header not matching up and follow on attempt at 2
byte addressing scheme grabs the correct data.
This costs us an extra ~3 milliseconds, which is a minor penalty
compared to the consistent image support we need to have.
Reported-by: Jason Kridner <jkridner@beagleboard.org>
Fixes: a58147c2db ("board: ti: common: board_detect: Do 1byte address checks first.")
Signed-off-by: Nishanth Menon <nm@ti.com>
Commit c0fce929564f("vexpress64: fvp: enable OF_CONTROL") added code to
consider a potential DTB address being passed in the x0 register, or
revert to the built-in DTB otherwise.
The former case was used when using the boot-wrapper, to which we sell
U-Boot as a Linux kernel. The latter was meant for TF-A, for which we
couldn't find an easy way to use the DTB it uses itself. We have some
quirk to filter for a valid DTB, as TF-A happens to pass a pointer to
some special devicetree blob in x0 as well.
Now the TF-A case is broken, when enabling proper emulation of secure
memory (-C bp.secure_memory=1). TF-A carves out some memory at the top
of the first DRAM bank for its own purposes, and configures the
TrustZone DRAM controller to make this region secure-only. U-Boot will
then hang when it tries to relocate itself exactly to the end of DRAM.
TF-A announces this by carving out that region of the /memory node, in
the DT it passes on to BL33 in x1, but we miss that so far.
Instead of repeating this carveout in our DT copy, let's try to look for
a DTB at the address x1 points to as well. This will let U-Boot pick up
the DTB provided by TF-A, which has the correct carveout in place,
avoiding the hang.
While we are at it, make the detection more robust: the length test (is
the DT larger than 256 bytes?) is too fragile, in fact the TF-A port for
a new FVP model already exceeds this. So we test x1 first, consider 0
an invalid address, and also require a /memory node to detect a valid DTB.
And for the records:
Some asking around revealed what is really going on with TF-A and that
ominous DTB pointer in x0: TF-A expects EDK-2 as its non-secure payload
(BL33), and there apparently was some long-standing ad-hoc boot protocol
defined just between the two: x0 would carry the MPIDR register value of
the boot CPU, and the hardware DTB address would be stored in x1.
Now the MPIDR of CPU 0 is typically 0, plus bit 31 set, which is defined
as RES1 in the ARMv7 and ARMv8 architectures. This gives 0x80000000,
which is the same value as the address of the beginning of DRAM (2GB).
And coincidentally TF-A put some DTB structure exactly there, for its
own purposes (passing it between stages). So U-Boot was trying to use
this DTB, which requires the quirk to check for its validity.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Peter Hoyes <peter.hoyes@arm.com>
- SPL fixes for STM32F7 MCUs
- Device tree alignement with kernelv6.0-rc4 for MCU's board
- Device tree alignement with kernelv6.0-rc3 for MPU's board
- Update DDR node for STM32MP15
- Cleanup config file for STM32MP1
- Update for cmd_stm32key command
- Fix compatible string to add partitions for STM32MP1
- Update for stm32programmer tool
-----BEGIN PGP SIGNATURE-----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=iA80
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220927' of https://source.denx.de/u-boot/custodians/u-boot-stm into next
- Increase SYS_MALLOC_F_LEN for STM32 MCU's board
- SPL fixes for STM32F7 MCUs
- Device tree alignement with kernelv6.0-rc4 for MCU's board
- Device tree alignement with kernelv6.0-rc3 for MPU's board
- Update DDR node for STM32MP15
- Cleanup config file for STM32MP1
- Update for cmd_stm32key command
- Fix compatible string to add partitions for STM32MP1
- Update for stm32programmer tool
xilinx:
- Add support for new Versal NET SOC
zynqmp:
- Use mdio bus for ethernet phy description
- Wire ethernet phy reset via i2c-gpio
versal:
- Config cleanup
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYzGwogAKCRDKSWXLKUoM
Ial4AJ9+4WHn0MV2X7gK1fyh4lUW7ggPhQCggsYlSoACgMgdji17SAPhCv/W3IA=
=BmA9
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2023.01-rc1-v2' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2023.01-rc1 (round 2)
xilinx:
- Add support for new Versal NET SOC
zynqmp:
- Use mdio bus for ethernet phy description
- Wire ethernet phy reset via i2c-gpio
versal:
- Config cleanup
Versal NET platform is based on Versal chip which is reusing a lot of IPs.
For more information about new IPs please take a look at DT which describe
currently supported devices.
The patch is adding architecture and board support with soc detection
algorithm. Generic setting should be very similar to Versal but it will
likely diverge in longer run.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/320206853dc370ce290a4e7b6d0bb26b05206021.1663589964.git.michal.simek@amd.com
Commit 37dc958947 ("global_data.h: Change ram_top type to phys_addr_t")
changed type of ram_top member from ulong to phys_addr_t but did not
changed types in board_get_usable_ram_top() function which returns value
for ram_top.
So change ulong to phys_addr_t type also in board_get_usable_ram_top()
signature and implementations.
Fixes: 37dc958947 ("global_data.h: Change ram_top type to phys_addr_t")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds general board files based on MT7981 SoCs.
MT7981 uses one mmc controller for booting from both SD and eMMC, and the
pins of mmc controller are also shared with spi controller.
So three configs are need for these boot types:
1. mt7981_rfb_defconfig - SPI-NOR and SPI-NAND
2. mt7981_emmc_rfb_defconfig - eMMC only
3. mt7981_sd_rfb_defconfig - SD only
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Add general board files based on MT7986 SoCs.
MT7986 uses one mmc controller for booting from both SD and eMMC.
Both MT7986A and MT7986B use the same pins for spi controller.
Configs for various boot types:
1. mt7986_rfb_defconfig - SPI-NOR and SPI-NAND for MT7986A/B
2. mt7986a_bpir3_emmc_defconfig - eMMC for MT7986A only
3. mt7986a_bpir3_sd_defconfig - SD for MT7986A only
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Current compatible string used to update SPI NAND and SPI NOR devices
can lead to a wrong partitions update (for example, SPI NAND partitions
added to SPI NOR node in the device tree). To avoid this wrong behavior,
use jedec,spi-nor compatible string for SPI NOR devices and spi-nand
compatible string for SPI NAND devices.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmMoEdgcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyNvEB/4nEeiBx7Lo1gK+79PJ
9kCUngglHRu3/+FJMpcOp+2b6sSW1IZs8qGBMAMFSRoFElrLMMbVEgBR0ZfJCl3c
It0xN9Buhe8muwtAdE8Amr4PddUEynzglVPpFUFfir6ZqFAcedmN6iuh+K82r7Be
7s/8tRb2hVp//TpkEntf2yxrYnyeW4qiXyUxbUhaUyyhkM3RBXySuY4qnaaLp3NY
R9rsIY5j3kA2QylebEamlXI+KDvszrGbkUOUUrlwkygQNR/GmAYQPlY1TdBwk0wE
U1CO8zQYaL3OY998lU32pMVClmwyXbn2i7KAyMm3TEgrfpjQsLTS2BK+w+RBdMGL
XGnt
=lRvM
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2023.01-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2023.01 cycle:
This feature set includes the important update on PIO4 pinctrl driver
that solves a long time mismatch between Linux and U-boot, related on
the unification of pinctrl and gpio driver support, now respecting the
pinctrl bindings ABI; and also support for pinctrl subnodes. The feature
set also adds support for PDA screen detection for sam9x60_curiosity
board , one fix for SD-Card reinsertion and one fix for sam9x60 clocks.
Call the PDA detection mechanism at boot time so that we can
have the pda environment variable ready for use.
Signed-off-by: Durai Manickam KR <durai.manickamkr@microchip.com>
Adjust the DRAM timing settings for this board per ones provided
by hardware department. The change is applied to the LPDDR4 MR11
register CA ODT configuration, from RZQ/6 to RZQ/3, which fixes
stability issues on subset of boards. The DDR PHY PIE block has
been updated accordingly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This code part is broken, remove it.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
This code part is broken, remove it.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
- Annotate boot devices available in spl_board_boot_device().
- Drop SD3_BOOT/MMC3_BOOT not available for boot on Verdin iMX8M Mini.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Prepare for optional job ring driver model. Sec may be initialized based
on the job ring information processed from the device tree.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Commit 99c7cc58e1 ("ddr: imx: Add i.MX9 DDR controller driver")
contains an inobvious side-effect which renders all systems using
DRAM controller at 3732 MT/s unbootable. The change is located in
ddrphy_init_set_dfi_clk(), where the switch case statement entry
3732 changed to entry 3733, so any board with DDR calibration data
for 3732 MT/s operations needs to be updated to 3733 MT/s to match
the change.
Since there is currently only one such board, update the board instead
of handling both 3732 and 3733 options in the driver. It is likely the
NXP MX8MP RPA update will follow and use the later value too.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The GW73xx-C revision and onward replaced the 5-port PCIe switch with a
4-port (dropping PCIe to one of the miniPCIe sockets) due to part
availability. This moved the PCI bus of the GbE eth1 device. Use a fixup
to adjust the dt accordingly so that local-mac-address assigned from dt
works on new revision boards.
While we are at it, rename 'blob' to 'fdt' for clarity.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
This commit adds board support for i.MXRT1170-EVK from NXP. This board
is an evaluation kit provided by NXP for i.MXRT117x processor family.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
It seems that waiting only 10 ms after releasing LAN switch from reset
is not enough for the strapping pins to latch the requested values.
P6_MODE[0] is latched to 0 instead of 1.
Increasing the delay to 50 ms fixes this issue.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Globally replace all occurances of WATCHDOG_RESET() with schedule(),
which handles the HW_WATCHDOG functionality and the cyclic
infrastructure.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
Currently Makefile produces final mpc85xx image when SPL is not used in
custom file u-boot-with-dtb.bin. It is quite confusing name as build
process produce also intermediate file standard file u-boot-dtb.bin (which
is just intermediate and not bootable). Other platforms use u-boot.bin
(UBOOT_BIN) as standard name for final bootable raw image.
So change Makefile rules and binman to produce final bootable file for
mpc85xx also into file u-boot.bin. There is just need for mpc85xx to not
define default rule for u-boot.bin then instruct binman (via DTS file) to
store final image into u-boot.bin (instead of u-boot-with-dtb.bin) and
finally rename target u-boot-with-dtb.bin to u-boot.bin.
With this change are also removed custom Makefile hacks for mpc85xx that it
produced non-standard output file. And also updated documentation.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
We currently have an if_type (interface type) and a uclass id. These are
closely related and we don't need to have both.
Drop the if_type values and use the uclass ones instead.
Maintain the existing, subtle, one-way conversion between UCLASS_USB and
UCLASS_MASS_STORAGE for now, and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
If kernel image in uImage or zImage format is not detected by
lowlevel_init.S code then do not clear memory location where image was
expected. If image is not detected then this memory region is unknown.
So do not unconditionally clear it.
Signed-off-by: Pali Rohár <pali@kernel.org>
The SPI and NAND board variants never went into production.
Drop those board variants.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
This patch adds a fixup function related to a PCIe FLR (Function Level
Reset) problem on the NIC23 PCIe board. This function is imported from
the Marvell Octeon 2013 U-Boot version as a (nearly) verbatim copy. It
uses the newly introduced cyclic infrastructure, so that this function
gets called every 100us, which is needed to detect this FLR issue.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Code supports board detection based on information available in EEPROM in
legacy or FRU format. But this is not enough for emulation and simulation
systems which are lacking these identification EEPROMs. But SOC itself has
normally registers for SOC identification. Based on them it is possible to
compose detected name. That's why prepare infrastructure in common location
for SOC platform detection which is called before board platform detection.
SOC platform detection shouldn't detect real silicon and should fallback to
current existing mechanism to identify boards based on EEPROMs.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/329a8da338927b082e26a958bf69bb18af072420.1662460837.git.michal.simek@amd.com
The commit ce39ee28ec ("zynqmp: Do not place u-boot to reserved memory
location") adds functionality for ZynqMP to read reserved memory node and
do not place U-Boot to reserved location. This functionality is generic
across all Xilinx SOCs that's why move it to common location to be used by
all Xilinx SOCs.
On zynq platform this is also fixing issue where U-Boot was placed to
locating which was reserved already which ends up with error message
"ERROR: reserving fdt memory region failed (addr=30000000 size=10000000
flags=4)" which is shown when bdinfo is called.
Tested on vck190, zcu102, zc706 and kc705 to cover all platforms.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/b0817807912f7c7af6a8e1cf9ee04e5ab5de5f6a.1661430188.git.michal.simek@amd.com
The commit 53b406369e ("DFU: Check the number of arguments and argument
string strictly") added strict control over string that 0:1 partition
definition is not valid anymore that's why use only device number without
partition ID. Device is specified by 2nd parameter and partition by 3rd.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/840eca944f4f2abeeb63b5d724f9ba5fe9a9213b.1660055571.git.michal.simek@amd.com
$fdt_addr is mandatory for systems which provides DTB in HW (e.g. ROM) and
wishes to pass that DTB to Linux.
Turris Mox contains DTB binary in SPI NOR memory at "dtb" partition which
starts at offset 0x7f0000 and is 0x10000 bytes long.
Armada 3700 CPU does not allow mapping SPI NOR memory into physical address
space like on other architectures and therefore set $fdt_addr variable to
memory range in RAM and loads this DTB binary from SPI NOR in misc_init_r()
function.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
When rescue mode was activated reset also bootdelay env variable to its
default value. This will ensure that reset button works and starts rescue
mode also in the case when user changed bootdelay env variable to -1 (which
has meaning to not start autoboot).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Store serial number from atsha cryptochip into the serial# env variable.
U-Boot automatically puts content of this variable into the root device
tree property serial-number when booting Linux kernel. Refactor turris
atsha code and from turris_atsha_otp_get_serial_number() function returns
directly string suitable for printing or storing into device tree. Because
during different boot stages is env storage read-only, it is not possible
to always store serial number into env storage. So introduce a new function
turris_atsha_otp_init_serial_number() which is called at later stage and
which ensures that serial number is correctly stored into env.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The user provided key address was not flushed in struct aes because of
the flushing location in the function.
Signed-off-by: Janne Ylalehto <ylalehto@gmail.com>
Link: https://lore.kernel.org/r/20220816124525.19671-1-ylalehto@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
- remove test on CONFIG_DM_REGULATOR in stm32mp1 board
and enable CONFIG_DM_REGULATOR for stm32f769-disco
- handle ck_usbo_48m clock provided by USBPHYC to fix the command 'usb start'
after alignment with Linux kernel v5.19 DT (clocks = <&usbphyc>)
- Fix SYS_HZ_CLOCK value for stih410-b2260 board
- Switch STMM32MP15x DHSOM to FMC2 EBI driver
- Remove hwlocks from pinctrl in STM32MP15x to avoid issue with kernel
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAmMZoW4ACgkQ4rK92eCq
k3W2MAgAsmy2aSlMYo/AGlJ/KCrZuk6OirNHtdOdacvbcdUUbpkNpBSjdkrRm2If
VUnY1utIIJe6gFgnBUxXJ3RF5FZuhkdawc6V25HtDp6H3WamzJknKs5Vc4TlKp59
hZCOto7/+G/cd2XLdCKFUBl+new1pdDPsEm56+57DeZ7QGAQRX35PUQ5+HBjQJ/N
n/wJgS6wkEdIQLLwmCVxbHUkC+pRotTza5F2A0qZJgYPMcMpVFYKtzIa4GbWB5YS
MKGHbM8f3C8RLPQaHHTRycoA2Yor1I52B4Oi7605c5zHQr9pjrgtWsernDzkIhsB
ThYHSYQBUBTY4HBfzFwzCkVGqqLWNg==
=PMFY
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220907' of https://source.denx.de/u-boot/custodians/u-boot-stm
- simplify the STM32MP15x package parsing code
- remove test on CONFIG_DM_REGULATOR in stm32mp1 board
and enable CONFIG_DM_REGULATOR for stm32f769-disco
- handle ck_usbo_48m clock provided by USBPHYC to fix the command 'usb start'
after alignment with Linux kernel v5.19 DT (clocks = <&usbphyc>)
- Fix SYS_HZ_CLOCK value for stih410-b2260 board
- Switch STMM32MP15x DHSOM to FMC2 EBI driver
- Remove hwlocks from pinctrl in STM32MP15x to avoid issue with kernel
CPLD in load_default mode ignores watchdog reset signal. It does not reset
board when watchdog triggers reset signal.
Detect load_default mode by GPIO7 - LOAD_DEFAULT_N and delete watchdog
max6370 node from device to prevent registering driver for non-working
watchdog.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Perform long overdue conversion of ad-hoc FMC2 EBI bus initialization
to upstream FMC2 EBI driver. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The tests on CONFIG_DM_REGULATOR, added to avoid compilation issues, can
now be removed, they are no more needed since the commit 16cc5ad0b4
("power: regulator: add dummy helper").
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
P1/P2 RDB boards have external max6370 watchdog connected to CPLD and this
watchdog is not deactivated on board reset. So if it is active during board
reset, it can trigger another reset when CPU is booting U-Boot. To prevent
possible infinite reset loop caused by external watchdog, turn it off
before reset.
Do it via a new board_reset_prepare() callback which is called from
do_reset() function before any reset sequence.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
CPLD's system reset register is buggy and requires workaround in U-Boot.
So use this kind of board reset only when there is no other reset option.
Introduce a new board_reset_last() callback which is last-stage
board-specific reset and implement CPLD's system reset in this new
board_reset_last() callback instead of board_reset() callback.
Fixes: 20fb58fc5a ("board: freescale: p1_p2_rdb_pc: Implement board_reset()")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
If watchdog timer was already set to non-disabled value then it means that
watchdog timer was already activated, has already expired and caused CPU
reset. If this happened then due to CPLD firmware bug, writing to wd_cfg
register has no effect and therefore it is not possible to reactivate
watchdog timer again. Watchdog starts working again after CPU reset via
non-watchdog method.
Implement this workaround (reset CPU when it was reset by watchdog) to make
watchdog usable again. Watchdog timer logic on these P1/P2 RDB boards is
connected to CPLD, not to SoC itself.
Note that reset does not occur immediately after calling do_reset(), but
after few ms later as real reset is done by CPLD. So it is normal that
function do_reset() returns. Therefore hangs after calling do_reset() to
prevent CPU execution of the rest U-Boot code.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
CPLD's system reset register on P1/P2 RDB boards is not autocleared after
flipping it. If this register is set to one in 100ms after reset starts
then CPLD triggers another CPU reset.
This means that trying to reset board via CPLD system reset register cause
reboot loop. To prevent this reboot loop, the only workaround is to try to
clear CPLD's system reset register as early as possible. U-Boot is already
doing it in its board_early_init_f() function, which seems to be enough as
register is cleared prior CPLD triggers another reset.
But board_early_init_f() is not called from SPL and therefore usage of SPL
can cause reboot loop.
To prevent reboot loop when using SPL, call board_early_init_f() function
in SPL too. For accessing CPLD memory space it is needed to have CPLD entry
in TLB.
With this change it is possible to trigger board reset via CPLD's system
reset register on P2020 RDB board.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In both the Freescale DDR controller and the SPD spec, bank address bits
are stored as the number of bank address bits minus 2. For example, if a
chip had 8 banks (3 total bank address bits), the value of
bank_addr_bits would be 1. This is rather surprising for users
configuring their memory manually, since they can't set bank_addr_bits
to the actual number of bank address bits. Rectify this.
There is at least one example of this kind of mistake already, in
board/freescale/t102xrdb/ddr.c. The documented MT40A512M8HX has two bank
address bits, but bank_addr_bits was set to 2, implying 4 bank address
bits. Such a value is reserved in BA_BITS_CS, but I suspect the
controller simply ignores the top bit, making this kind of mistake
harmless, if misleading.
Fixes: e8a7f1c32b ("powerpc/t1023rdb: Add T1023 RDB board support")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Depending on the boot source, set different CLI prompts. This will help
the user to figure out in which mode the bootloader was started. There
are two special modes: failsafe and SDHC boot.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
During startup the SPL will print where the u-boot proper is read from.
Instead of using the default names, provide more user friendly names.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The board is able to boot from the following source:
- user-updateble SPI flash
- write-protected part of the same SPI flash
- eMMC
- SD card
Implement the needed function hooks to support all of these boot
sources.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Commit 6aa4fe3912 ("dm: core: Rename and fix uclass_get_by_name_len()")
changed uclass_get_device_by_name() to an exact match when previously it
behaved as a prefix match.
The roc-cc code relied on this prefix match by only specifying part of
the device name. Fix this by using the full name including the address.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
As the Renesas Reduced Pin Count Interface may be locked by TF-A, it is
disabled by default[1]. When unlocked, TF-A passes a DT fragment to
enable it, which is applied to the U-Boot DT[2].
Unlike the memory layout, the RPC-IF enablement is not propagated to
subsequent software. Hence e.g. Linux cannot know if the RPC-IF is
locked or not, and will lock-up when trying to access the RPC-IF when
locked.
Fix this by checking if the RPC-IF is enabled in the TF-A DT fragment, and
setting the status of the RPC-IF device node in the target DT, if
present, to "okay". Do this only when a "flash" subnode is found, to
avoid errors in subsequent software when the RPC-IF is not intended to
be used.
Note that this requires the status of the RPC-IF node to be set to
"disabled" in the target DT, just like in the U-Boot DT.
[1] commit 3d5f45c95c ("ARM: dts: rmobile: Disable RPC HF by
default")
[2] commit 361377dbdb ("ARM: rmobile: Merge prior-stage firmware
DT fragment into U-Boot DT on Gen3")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable d-cache early in SPL right after DRAM is started up.
This reduces U-Boot proper load time by 650ms when loaded
from SPI NOR.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Philip Oberfichtner <pro@denx.de>
There are three different kinds of EEPROM possibly present on boards.
1. 1byte address. For those we should avoid 2byte address in order
not to rewrite the data. Second byte of the address can potentially
be interpreted as the data to write.
2. 2byte address with defined behaviour. When we try to use 1byte
address they just return "FF FF FF FF ... FF"
3. 2byte address with undefined behaviour (for instance, 24LC32AI).
When we try to use 1byte address, then their internal read
pointer is changed to some value. Subsequential reads may be
broken.
To gracefully handle both case #1 and case #3 we read all required
data from EEPROM at once (about 80 bytes). So either all the data is
valid or we fallback to 2byte address.
Cc: Nishanth Menon <nm@ti.com>
Fixes: a58147c2db ("board: ti: common: board_detect: Do 1byte address checks first.")
Reference: https://lore.kernel.org/all/CAJs94Ebdd4foOjhGFu9Bop0v=B1US9neDLxfhgcY23ukgLzFOQ@mail.gmail.com/
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Acked-by: Nishanth Menon <nm@ti.com>
For USB3 host controller to detect devices on the bus it is required to
enable a PMIC GPIO: usb_vbus_boost_pin. So enable that during board
specific initialization.
And since this PMIC GPIO parsing is quite u-boot specific, so add a
DT override to qcs404-evb-uboot.dtsi to represent usb_vbus_boost_pin.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Use the new mvebu GPIO driver and convert all the function calls to the
former kirkwood GPIO driver. This means that we are now using the LED
uclass and the regulator uclass. Unfortunately, the GPIO LED doesn't
offer a blinking method. Thus we are now stuck with solid on and off
states, which makes debugging a bit harder. Also, there is no GPIO fan
driver for now.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
If something is wrong with the environment, we cannot rely on a proper
u-boot operation anymore. In fact, it is possible, that we never reach
misc_init_r() with a broken environment.
Also don't enable the netconsole by environment settings. This way the
user don't have to reconfigure the environment. Instead the network
console is only enabled when the push button is pressed during boot.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
The board code needs this to be set. Otherwise, the recovery mechanism
doesn't work. Therefore, select this option automatically with the
board.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Cleanup the included header files in the board code. These are all
leftovers from earlier days.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
This is not needed. The user can force setting the variables with
"setenv -f".
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
- Add distro boot to board include file and deconfig file
- Miscellaneous changes:
- Remove Gerald from maintainer list (email bounced)
- Add CONFIG_SUPPORT_PASSING_ATAGS and friends to support legacy
kernel method of booting (e.g. OpenWrt) with appended DTB.
- Add CONFIG_UBIFS_SILENCE_MSG to reduce binary size.
Note that this patch is depended on the following patch:
https://patchwork.ozlabs.org/project/uboot/patch/20220807192709.21717-1-pali@kernel.org/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
mbus driver is initialized from arch_cpu_init() callback which is called
before relocation. This driver stores lot of functions and structure
pointers into global variables, so it is data position dependent.
Therefore after relocations all pointers are invalid and driver does not
work anymore as all pointers referes to the old memory, which overlaps with
CONFIG_SYS_LOAD_ADDR and ${loadaddr}.
For example U-Boot fuse command crashes if loadaddr memory is cleared or
rewritten by some image loaded by U-Boot load command.
mw.w ${loadaddr} 0x0 10000
fuse read 0 1 2
Fix this issue by removing of all mbus global variables in which are stored
pointers to structures or functions which changes during relocation. And
replace it by direct function calls (not via pointers). With this change
fuse command finally works.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Stefan Roese <sr@denx.de>
When Mox SFP module is connected after Topaz or Peridot module then port DT
node already contains "sfp" label. But Mox SFP module can be connected also
without Topaz or Peridot module in which case it is connected directly into
he eth1 DT node, which is without any label. So add "sfp" label into eth1
DT node in this case.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
There are already more MCU firmware versions for Turris Omnia in
production, so display git commit (version) of the MCU firmware during
U-Boot startup. It will help to identify what version of MCU firmware is
Turris Omnia using.
MCU firmware for Turris Omnia is open source and available at website:
https://gitlab.nic.cz/turris/hw/omnia_hw_ctrl
It can be updated from running system via i2c bus with this tool:
https://gitlab.nic.cz/turris/omnia-mcutool
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
SPI0 CS0 Flash is mapped to address range 0xD4000000 - 0xD7FFFFFF by BootROM.
Proper U-Boot removes this direct mapping. So it is available only in SPL.
This applies for all 32-bit Armada BootROMs. SPL mvebu code is used only on
32-bit Armada SoCs. So move env_sf_get_env_addr() function from Turris
Omnia board to common SPL mvebu code and add proper checks for SPI0 CS0.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The kmtegr1 board is out of maintenance and can be removed. As it is the
only board in the tree using MPC8309 the support for this CPU is dropped
completely.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
This board is missing migration to CONFIG_DM, which had a deadline of
v2020.01, which is now more than 2 years passed due. Remove it.
Cc: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that we are about to enable DM_ETH by default, remove legacy code.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Now that we are about to enable DM_ETH by default, remove legacy code.
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that we are about to enable DM_ETH by default, remove legacy code.
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that we are about to enable DM_ETH by default, remove legacy code.
Cc: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This platform needs to be converted to use DM_ETH as the deadline is 2
years passed due. Disable networking support for now.
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
As this driver has been converted to DM_ETH and the migration deadline
is 2 years passed, remove the legacy code and callers.
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
There is some code here for the legacy non-DM_ETH case, add a guard
around it.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have been orphaned for some time and are behind on various
DM migrations. Remove them.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The *aqds* platforms have not been migrated to be able to enable
CONFIG_DM_ETH with CONFIG_FMAN_ENET. Disable CONFIG_FMAN_ENET on these
platforms.
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: Pramod Kumar <pramod.kumar_1@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board is behind on several mandatory DM migrations and is missing
OF_CONTROL support that makes other conversions impossible. Remove it.
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board is behind on several mandatory DM migrations and is missing
OF_CONTROL support that makes other conversions impossible. Remove it.
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board is behind on several mandatory DM migrations and is missing
OF_CONTROL support that makes other conversions impossible. Remove it.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Uri Mashiach <uri.mashiach@compulab.co.il>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board is not converted to use CONFIG_DM, well passed the migration
deadline. Remove it.
Cc: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To ease maintenance, let's keep only the main mx28evk_defconfig
and remove the other variants that have not been migrated to DM.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
pcm051_rev3_defconfig config (Phytec Wega board) has been dropped in
64efd11d ("arm: Remove pcm051 board")
due to expired migration deadlines. Here, pcm051_rev3_defconfig support is
reintroduced.
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some of config options are board specific and should be set in into their
default values automatically. So move them from defconfig file to Kconfig
definitions to ensure that possible user custom defconfig files would have
these required options also enabled.
Signed-off-by: Pali Rohár <pali@kernel.org>
Now when board starup code does not copy image to CONFIG_SYS_TEXT_BASE
address there is no need to calculate all addresses from base address at
runtime. The only address which needs to be calculated is attached kernel
image address which can be simplified at compile time without need to know
CONFIG_SYS_TEXT_BASE address or relocation address at the runtime.
Signed-off-by: Pali Rohár <pali@kernel.org>
Expression (r + (r0 - r1)) produce same result as (r - (r1 - r0)). So it
does not matter which one is called. Always call the first option and
remove second one.
Signed-off-by: Pali Rohár <pali@kernel.org>
Switch from custom board specific fixup/copy code to U-Boot generic
position independent code provided by config option POSITION_INDEPENDENT.
This also slightly decrease size of u-boot.bin binary (by 52 bytes). Note
that option POSITION_INDEPENDENT increase size but not more than custom
board fixup/copy code which is being deleted (as it is not needed anymore).
Signed-off-by: Pali Rohár <pali@kernel.org>
Prior starting copy of kernel image to target location, invalidate also
zImage magic header. This ensures that on target location would be image
with valid header only in the case valid header was also in the source
location and copy from source to target finished successfully. Copy is
always skipped when kernel image in source location is invalid.
Add also comment to the code which explain what is the code doing.
Fixes: cc434fccba ("Nokia RX-51: Add support for booting kernel in zImage format")
Signed-off-by: Pali Rohár <pali@kernel.org>
My professional e-mail will change and the BayLibre one will
bounce after mid-september of 2022.
This updates the MAINTAINERS files and adds an entry in the
.mailmap file.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
The LS1043ARDB rev v7.0 board replaces the AQR105 PHY on MAC9 with an
AQR113C PHY. The address of the PHY on the MDIO bus changes from 0x1 to
0x8. Enable CONFIG_OF_BOARD_FIXUP and update both u-boot and Linux device
trees to reflect this change.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
caam driver model enabled in spl for secure boot.
fsl_rsa_mod_exp driver enabled in spl for validating uboot image.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
This driver has not been converted to DM_ETH. The migration deadline
passed 2 years ago.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: David Feng <fenghua@phytium.com.cn>
Cc: Liviu Dudau <liviu.dudau@foss.arm.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
This board is behind on several mandatory DM migrations and is missing
OF_CONTROL support that makes other conversions impossible. Remove it.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This board is behind on several mandatory DM migrations and is missing
OF_CONTROL support that makes other conversions impossible. Remove it.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Heiko Schocher <hs@denx.de>
To reduce code duplication, let the stm32 based DH boards use the common
code for setting up their MAC addresses.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
To reduce code duplication, let the imx8 based DH boards use the common
code for setting up their MAC addresses.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
To reduce code duplication, let the imx6 based DH boards use the common
code for setting up their MAC addresses.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
This is a starting point for unifying duplicate code in the DH board
files. The functions for setting up MAC addresses are very similar for
the i.MX6, i.MX8 and stm32mp1 based boards.
All pre-existing implementations follow the same logic:
(1) Check if ethaddr is already set in the environment
(2) If not, try to get it from a board specific location (e.g. fuse)
(3) If not, try to get it from eeprom
After this commit, (1) and (3) are implemented as common functions,
ready to be used by board specific files.
Furthermore there is an implementation of (2) for imx based boards.
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
The booting flow is SPL -> OpenSBI -> U-Boot.
The boot hart may change after OpenSBI and may not always be hart0,
so wrap the related branch instruction with M-MODE.
Current DTB setup for XIP is not valid.
There is no chance for CONFIG_SYS_FDT_BASE, the DTB address used
in XIP mode, to be returned. Fix this.
Fixes: 2e8d2f8843 ("riscv: Remove OF_PRIOR_STAGE from RISC-V boards")
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Update mv88e61xx_hw_reset() to use the DM_GPIO API to toggle the reset
line for the linkstreet switch.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Replace code that accessed the GPIO registers directly with code that
makes use of the LED_GPIO driver.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Linux kernel DTS files renamed spi-nor@0 node to flash@0 which effectively
broke U-Boot to boot new Linux kernel versions correctly.
So remove hardcoded spi-nor device tree path from Turris Omnia board code
and replace it by searching for mtd node by compatible string.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Sometimes fixup_mtd_partitions() prints during booting kernel error
"Failed fixing SPI NOR partitions!" because it does not have enough space
for creating all paritions nodes. So increase fdt size.
Fixes: 92f36c8e74 ("arm: mvebu: turris_omnia: fixup MTD partitions in Linux' DTB")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Behún <kabel@kernel.org>
All partitions are created by fixup_mtd_partitions() function, so they do
not have to exist just for their removal need.
Fixes: 92f36c8e74 ("arm: mvebu: turris_omnia: fixup MTD partitions in Linux' DTB")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Behún <kabel@kernel.org>
New Turris Omnia HW board revision requires that software controls
peripheral reset signals, namely PERST# signals on mPCIe slots, ethernet
phy reset and lan switch reset. Those pins are connected to MCU controlled
by MCU i2c API as GPIOs. On new HW board revision those pins stay in reset
after board reset and software has to release these peripherals from reset
manually. MCU announce this requirement by FEAT_PERIPH_MCU bit in
CMD_GET_FEATURES command.
On older HW board revisions when FEAT_PERIPH_MCU is not announced, all
those reset signals are automatically released after board finish reset.
Detect FEAT_PERIPH_MCU bit in board_fix_fdt() and ft_board_setup()
functions and insert into device tree blob pcie "reset-gpios" and eth phy
"phy-reset-gpios" properties with corresponding MCU gpio definitions.
PCIe and eth PHY drivers then automatically release resets during device
initialization. Both U-Boot and Linux kernel drivers support those device
tree reset properties.
Initialization of lan switch on new HW board revision is more complicated.
Switch strapping pins are shared with switch RGMII pins. And strapping pins
must be in specific configuration after releasing switch reset. Due to pin
sharing, it is first required to switch A385 side of switch pins into GPIO
mode, set strapping configuration, release switch from reset and after that
switch A385 pins back to RGMII mode.
Because this complicated setup is not supported by switch DSA drivers and
cannot be expressed easily in device tree, implement it manually in SPL
function spl_board_init(). So in proper U-Boot and OS/kernel would be lan
switch initialized and be in same configuration like it was on old HW board
revisions (where reset sequence did those steps at hardware level).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Behún <kabel@kernel.org>
Different Turris Omnia HW board revisions contains different MCU.
Show type in show_board_info() to easily identify which MCU is populated.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Behún <kabel@kernel.org>
A large number of files include <flash.h> as it used to be how various
SPI flash related functions were found, or for other reasons entirely.
In order to migrate some further CONFIG symbols to Kconfig we need to
not include flash.h in cases where we don't have a NOR flash of some
sort enabled. Furthermore, in cases where we are in common code and it
doesn't make sense to try and further refactor the code itself in to new
files we need to guard this inclusion.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FLASH_ERASE_TOUT
CONFIG_SYS_FLASH_LOCK_TOUT
CONFIG_SYS_FLASH_UNLOCK_TOUT
CONFIG_SYS_FLASH_WRITE_TOUT
In practice, for two m68k platforms we move to hard-coding with a
comment the timeout values, rather than try and make convoluted Kconfig
logic. We add options for the write and erase options to the pic32
flash driver, as this driver does make use of them. Everywhere else
these are unreferenced values.
Signed-off-by: Tom Rini <trini@konsulko.com>
All platforms today define CONFIG_SYS_DDR_RAW_TIMING, so drop the code
for this option being unset.
Cc: Qiang Zhao <qiang.zhao@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This is the only platform defining and using CONFIG_SYS_MEM_SIZE, switch
to using CONFIG_SYS_SDRAM_SIZE for consistency.
Cc: Paul Burton <paul.burton@mips.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a number of CONFIG_SYS_xxx_SIZE options to describe the amount
main memory available. Rework CONFIG_SYS_DDR_SIZE, which described a
size in number of MiB to use CONFIG_SYS_SDRAM_SIZE which is most often
used as a number of bytes. Use shifts of this option when required.
Signed-off-by: Tom Rini <trini@konsulko.com>
Since commit 103c5f1806 ("mmc: Rename MMC_SUPPORT to MMC"),
SPL_MMC_SUPPORT is named SPL_MMC, so let's fix the ifdef.
Fixes: fbc6b14143 ("imx: imx8mp_rsb3720a1: convert to DM_SERIAL")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
On some boards upper 4 bits of i2c boot input data (register 0) are
inverted. Information which bits are inverted is stored in register 2.
So invert read input data back according to register 2 prior processing
them. This fixes printing "rom_loc: value" line during booting.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
U-Boot for initial L2 SRAM uses L2 memory-mapping mode and not L2 with
locked lines. P2020 reference manual about L2 memory-mapping mode says:
Accesses to memory-mapped SRAM are cacheable only in the corresponding
e500 L1 caches.
So there is no need to set Caching-Inhibit I-bit for second part of initial
L2 SRAM mapping in TLB entry. Remove it. First part of initial L2 SRAM
mapping already does not have I-bit set.
For more details see also:
https://lore.kernel.org/u-boot/20220508150844.qqxg452rs4wtf5bs@pali/
Signed-off-by: Pali Rohár <pali@kernel.org>
This driver registers GPIO controller and allows U-Boot to control GPIO
pins on MCU which is connected to Turris Omnia via i2c.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
start of test for fdt command
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmLgRtERHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYXFwgAlALOMj3bwwsIAXNa5j/hPb3j/ecIqXgn
ocyxN+U5eSb2Ju5Jc9QmSeUMnGrii9+PW9j0JApdHrbUgBI2Sx+zwqMTIfA+BS05
4xXZgk5jOT+we2489FjgFcplv+dIuVlsB/Zo6zTbZyjkobfilYsZEGYHJ/CYNaIH
n7EmZeby1cXL7DMCxT39d3hD43XSX8cqQ1IIiF9DgtHQYs2Ff8dFcbWArSdgLX3o
Eob2Qj/GjScg87zjZcsgZajWJMHUfMeD5ZiKN2fR0T/wOdO1WtzFoF2Mt8KZcW1j
BD1shgBCMSSl5EgRG1BQZw4Sa92W2IBlbJ9tfIh8qnWOzEBzOs/M6w==
=lsO4
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-26jul22' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm.git
minor dm- and fdt-related fixes
start of test for fdt command
Set ARM clock to OD frequency 1.7Ghz, since we have set PMIC VDD_SOC
to Overdrive voltage 0.9V
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since iMX9 uses S401 which shares the API with iMX8ULP. So move S400
MU driver and API to a common place and selected by CONFIG_IMX_SENTINEL
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update this feature so that it works on sandbox, using a basic identity
mapping. This allows us to run the 'ut addrmap' test.
Also fix up the test to use the correct macros to access the linker
list, so that the 'ut addrmap' command actually works.
Signed-off-by: Simon Glass <sjg@chromium.org>
Store a set of supported bitstream types in xilinx_desc structure.
It will be used to determine whether an FPGA image is able to be
loaded with a given driver.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Tested-by: Ricardo Salveti <ricardo@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-4-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
UUID is already recorded when FRU is parsed but it is not copied to local
structures and exported to variable that's why simply add it.
Data is saved in binary format but there must be conversion to string for
exporting it to variable and string should be in uuid format too.
One way how to use it directly is to setup pxeuuid based on it. For
example via preboot with "setenv pxeuuid ${board_uuid}"
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/1dfa4b4220a508abc05351da2119880811b77612.1658413156.git.michal.simek@amd.com
With commit ce39ee28ec ("zynqmp: Do not place u-boot to reserved memory
location"), the function board_get_usable_ram_top() is allocating
MMU_SECTION_SIZE of about 2MB using lmb_alloc(). But we dont have this
much memory in case of mini U-Boot.
Keep these functions which use lmb under CONFIG_LMB so that they are
compiled and used only when LMB is enabled.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/75e52def75f573e554a6b177a78504c128cb0c4a.1657183534.git.michal.simek@amd.com
The first AM6x device was the AM654x, but being the first we named it
just AM6, since more devices have come out with this same prefix we
should switch it to the normal convention of using the full name of the
first compatibility device the series. This makes what device we are
talking about more clear and matches all the K3 devices added since.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is no longer needed as the SA2UL can now be shared with Linux.
Leave the SA2UL DT node enabled.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for Qualcomm QCS404 SoC based evaluation board.
Features:
- Qualcomm Snapdragon QCS404 SoC
- 1GiB RAM
- 8GiB eMMC, uSD slot
U-boot is chain loaded by ABL in 64-bit mode as part of boot.img.
For detailed build and boot instructions, refer to
doc/board/qualcomm/qcs404.rst.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
