Commit graph

777 commits

Author SHA1 Message Date
Stephen Warren
39e3711839 tegra: Compulab TrimSlice board support
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07 14:07:19 +02:00
Stephen Warren
d5ebc937c9 tegra: Whistler board support
Whistler is a highly configurable Tegra evaluation and development board.
This change adds support for the following specific configuration:

E1120 motherboard
E1108 CPU board
E1116 PMU board

The motherboard configuration switches are set as follows:
SW1=0 SW2=0 SW3=5
S1/S2/S3/S4 all on, except S3 7/8 are off.

Other combinations of daugher boards may work to varying degrees, but will
likely require some SW adjustment.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-07-07 14:07:17 +02:00
Prabhakar Kushwaha
7530d341c7 powerpc/mpc85xx:Add BSC9131 RDB Support
BSC9131RDB is a Freescale reference design board for BSC9131 SoC. BSC9131 SOC
 is an integrated device that targets Femto base station market. It combines
 Power Architecture e500v2 and DSP StarCore SC3850 core technologies with
 MAPLE-B2F baseband acceleration processing elements

  BSC9131RDB Overview
   -----------------
     -1Gbyte DDR3 (on board DDR)
     -128Mbyte 2K page size NAND Flash
     -256 Kbit M24256 I2C EEPROM
     -128 Mbit SPI Flash memory
     -USB-ULPI
     -eTSEC1: Connected to RGMII PHY
     -eTSEC2: Connected to RGMII PHY
     -DUART interface: supports one UARTs up to 115200 bps for console display
Apart from the above it also consists various peripherals to support DSP
functionalities.

This patch adds support for mainly Power side functionalities and peripherals

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Akhil Goyal <Akhil.Goyal@freescale.com>
Signed-off-by: Rajan Srivastava <rajan.srivastava@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2012-07-06 17:30:29 -05:00
Holger Brunck
c67d2ff217 MAINTAINERS: cleanup for keymile boards
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-06-15 17:12:40 -05:00
Holger Brunck
0f2b721c80 powerpc/83xx: add kmcoge5ne board support
This board is a MPC8360 board. Two flashes are present
a NOR flash were u-boot and the u-boot environment is stored
and a NAND flash for the application code. This board has 512MB
SDRAM.

Additionaly we introduce a common km8360.h file and convert kmeter1 to
use this.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Christian Herzig <christian.herzig@keymile.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-06-15 17:12:40 -05:00
Nobuhiro Iwamatsu
bfc93fb47d sh: Add support for AP-SH4A-4A board
The AP-SH4A-4A board has SH7734, 64MB DDR2-SDRAM, USB,
Ethernet, and more.

This patch supports the following functions:
  - 64MB DDR2-SDRAM
  - 16MB NOR Flash memory
  - Serial console (SCIF)
  - Ethernet (SH-Ether with Gigabit)
  - I2C

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2012-05-28 09:12:54 +09:00
Nobuhiro Iwamatsu
8ca805e102 sh: Add support for r0p7734 board
The r0p7734 board has SH7734, 128MB DDR2-SDRAM, USB,
Ethernet, and more.

This patch supports the following functions:
- 128MB DDR2-SDRAM
- 32MB NOR Flash memory
- Serial console (SCIF)
- Ethernet (SH-Ether/SMSC)

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2012-05-28 09:12:53 +09:00
SRICHARAN R
2ca4a209a5 OMAP4/5: Change omap4_sdp, omap4_panda, omap5_evm maintainer
Signed-off-by: R Sricharan <r.sricharan@ti.com>
CC: Aneesh V <aneesh@ti.com>
CC: Tom Rini <trini@ti.com>
Acked-by: Aneesh V <aneesh@ti.com>
2012-05-15 08:31:41 +02:00
David Purdy
1d0f5fa11d kirkwood: add support for Cloud Engines Pogoplug E02
This patch adds support for Cloud Engines Pogoplug E02

Information regarding the CE Pogoplug E02 board can be found at:
http://archlinuxarm.org/platforms/armv5/pogoplug-v2-pinkgray

Signed-off-by: Dave Purdy <david.c.purdy@gmail.com>
Cc: prafulla@marvell.com
Cc: albert.u.boot@aribaud.net
2012-05-15 08:31:22 +02:00
Luka Perkov
e5841e1211 kirkwood: add NAS62x0 board support
Add support for new boards RaidSonic ICY BOX NAS6210 and NAS6220.

NAS6210 has 1 SATA and 1 eSATA port while NAS6220 has 2 SATA ports.

More information about the boards can be found here:

http://www.raidsonic.de/en/products/nas-systems.php?we_objectID=7036
http://www.raidsonic.de/en/products/nas-systems.php?we_objectID=7515

Signed-off-by: Luka Perkov <uboot@lukaperkov.net>
Signed-off-by: Gerald Kerma <dreagle@doukki.net>
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
2012-05-15 08:31:22 +02:00
Vladimir Zapolskiy
463ec1caa3 devkit3250: add Timll DevKit3250 board initial support
This change adds a basic support for Embest/Timll DevKit3250 board,
NOR and UART are the only supported peripherals for a moment. The board
doesn't require low-level init, because the initial SDRAM and GPIO
configuration is performed during kickstart bootloader execution.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
2012-05-15 08:31:22 +02:00
Macpaul Lin
b9725ae3f3 board/adp-ag102: add configuration of adp-ag102
board:
Add config file of board adp-ag102
Add adp-ag102 into boards.cfg
Add adp-ag102 into MAINTAINERS

doc:
add README of ag102

Signed-off-by: Macpaul Lin <macpaul@andestech.com>
2012-04-22 16:58:23 +08:00
Tom Rini
c8da405c85 OMAP: Move omap1510inn to Unmaintained / Orphaned
After removing omap1610inn for not building, move omap1510inn to
orphaned.  Also update boards.cfg to note it's part of the 'omap' SoC to
make sure the board is built more often and future breakage noticed
quicker.

Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
2012-04-16 14:47:58 +02:00
Tom Rini
76e2c169a5 OMAP: Remove omap1610inn-based boards
The CS_AUTOBOOT configurations have been broken for a long time.
Kshitij Gupta is no longer at TI making these broken and orphaned
boards, so remove.

Signed-off-by: Tom Rini <trini@ti.com>
2012-03-29 08:19:29 +02:00
Tom Rini
6c11dcd8c3 omap3_beagle: Change MAINTAINERS entry
Cc: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Dirk Behme<dirk.behme@gmail.com>
2012-02-27 21:19:24 +01:00
Tom Rini
fd7962e2c4 am335x_evm: Change MAINTAINERS entry
Signed-off-by: Tom Rini <trini@ti.com>
2012-02-27 21:19:24 +01:00
Wolfgang Denk
06576b2efc Merge branch 'master' of git://git.denx.de/u-boot-blackfin
* 'master' of git://git.denx.de/u-boot-blackfin:
  Blackfin: pata_bfin: fix printf warning
  Blackfin: bfin_nand: mark local func static
  linkage.h: move from blackfin to common includes
  Blackfin: br4: new board port
  Blackfin: add in/out le32 variants
  post: add blackfin to the post_time_ms list
  Blackfin: bf537-stamp: drop board reset workaround
  Blackfin: pr1: new board port
2012-02-13 23:13:22 +01:00
Dimitar Penev
051a5f30f1 Blackfin: br4: new board port
This adds support for the BR4 Appliance.  It is a quad channel ISDN BRI
board based on Blackfin BF537 CPU.

Signed-off-by: Dimitar Penev <dpn@switchfin.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-02-12 15:03:25 -05:00
Dimitar Penev
939b150ae5 Blackfin: pr1: new board port
This add support for the PR1 Appliance - Asterisk based ISDN PRI PBX.
This board is Blackfin BF537 based.  The schematics are not fully opened.

Signed-off-by: Dimitar Penev <dpn@switchfin.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-02-12 15:03:25 -05:00
Christian Riesch
9a3aae22ed arm, davinci: Add support for the Calimain board from OMICRON electronics
This patch adds support for the Calimain board from
OMICRON electronics GmbH. The board features a Texas Instruments AM1808
SoC, 128 MB DDR2 memory, and 64 MB NOR flash memory connected to CS2 and
CS3.

Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
2012-02-12 10:11:33 +01:00
Ilya Yanok
4ab779cba6 mcx: support for HTKW mcx board
This patch adds support for the HTKW mcx AM3517-based board.
Serial, Ethernet, NAND, MMC, RTC, EHCI USB host and both
NAND and MMC SPLs are supported.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <tom.rini@gmail.com>
Cc: Detlev Zundel <dzu@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2012-02-12 10:11:31 +01:00
Stefano Babic
1fdabedd0c ARM: omap3: Added Teejet mt_ventoux
The mt_ventoux board is a custom board using
the Technexion TAM3517 module.

The patch fixes also the mtdparts variable in the
TAM3517 common configuration file.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Ilya Yanok <yanok@emcraft.com>
CC: Igor Grinberg <grinberg@compulab.co.il>
CC: Tom Rini <tom.rini@gmail.com>
Cc: Detlev Zundel <dzu@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2012-02-12 10:11:31 +01:00
Chander Kashyap
0aee53bacc EXYNOS: Add SMDK5250 board support
SMDK5250 board is based on Samsungs EXYNOS5250 SoC.

Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-02-12 10:11:30 +01:00
HeungJun, Kim
89f95492ec ARMV7: Exynos4: Add support for TRATS board
This patch adds support for Samsung TRATS board

Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-02-12 10:11:29 +01:00
Stefan
bfacf4667a kirkwood: add support for D-Link DNS-325
This patch adds support for D-Link DNS-325 ShareCenter NAS.

Signed-off-by: Stefan Herbrechtsmeier <stefan@code.herbrechtsmeier.net>
Cc: prafulla@marvell.com
Cc: albert.u.boot@aribaud.net
2012-02-12 10:11:28 +01:00
Thomas Weber
8167af14d5 OMAP3: Add Corscience Tricorder board
Tricorder is a board which is very similar to the Devkit8000. It
is designed as a base platform for further medical devices.

www.corscience.de/en/medical-engineering/products/multiparameter/mp10-board.html

Signed-off-by: Thomas Weber <weber@corscience.de>
2012-02-12 10:11:23 +01:00
Stephen Warren
2996e2dcc0 tegra2: Add support for Compal Paz00 (Toshiba AC100)
The Toshiba AC100 (Compal code-name Paz00, aka Dynabook AZ) is a netbook
derived from the NVIDIA Tegra Harmony reference board. It ships with
Android, but is often repurposed to run Linux. This patch adds just enough
support to get a U-Boot serial console, and the ability access built-in
eMMC and the external SD slot.

v2:
* Rebased on latest HEAD, incorporated changes made to other board files.
* Moved board files from board/nvidia to board/compal.
* Switched to correct odmdata value. This required add the previous patch
  to fix U-Boot's interpretation of the odmdata RAM size field.
* Removed nvmem= from default Linux kernel command-line; no drivers use the
  reserved memory yet, so there's no point reserving it.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2012-02-12 10:11:22 +01:00
Peter Barada
86887f8ea1 ARMV7: Add support For Logic OMAP35x/DM37x modules
This patch adds basic support for OMAP35x/DM37x SOM LV/Torpedo
reference boards. It assumes U-boot is loaded to SDRAM with the
help of another small bootloader (x-load) running from SRAM.

Signed-off-by: Peter Barada <peter.barada@logicpd.com>
Cc: Tom Rini <tom.rini@gmail.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2012-01-16 08:40:10 +01:00
Jason Liu
bc5833c49a i.mx: i.mx6q: add the initial support for i.mx6q Sabre Lite board
Add the initial support for Freescale i.MX6Q Sabre Lite board

Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Jason Liu <jason.hui@linaro.org>
CC: Eric Nelson <eric.nelson@boundarydevices.com>
2012-01-16 08:40:10 +01:00
Fabio Estevam
29f75a5ce5 mx28evk: Add initial support for MX28EVK board
Add initial support for Freescale MX28EVK board.

Tested boot via SD card and by loading a kernel via TFTP through
the FEC interface.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-01-16 08:40:09 +01:00
Stefan Kristiansson
f1f441afc4 openrisc: Add MAINTAINERS entry
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
2012-01-13 21:17:08 +01:00
Holger Brunck
f5a474bd7a powerpc/83xx/km: add support for 8321 based tuge1 board
This board is similar to our tuxx1 target. But on this board there
is only one application specific chip select configured.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-01-09 20:10:34 -06:00
Holger Brunck
5f2a44d5ea powerpc/83xx/km: merge tuxa and tuda1 boards to tuxx1
These boards are from a u-boot point of view identical. So collect
the two headerfiles to one, to decrease maintenance.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-01-09 20:10:33 -06:00
Thierry Reding
c91915e905 tegra2: Add Avionic Design Medcom support.
The Medcom is a 16:9 15" terminal that is used for patient infotainment
in hospitals.

Changes in v3:
  * Remove unused implementation of gpio_config_uart().
  * Implement MMC/SD card detection.
  * Drop board_mmc_getcd() which is now implemented by common Tegra2
    code.
  * Add MAINTAINERS entry.

Changes in v2:
  * No longer override the default CONFIG_SYS_TEXT_BASE setting.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2011-12-24 10:23:32 +01:00
Thierry Reding
4026aca6d6 tegra2: Add Avionic Design Plutux support.
The Plutux is a set-top box device based on the Tamonten processor
module. It can be connected to a display via an HDMI output.

Changes in v3:
  * Remove unused implementation of gpio_config_uart().
  * Implement MMC/SD card detection.
  * Drop board_mmc_getcd() which is now implemented by common Tegra2
    code.
  * Add MAINTAINERS entry.

Changes in v2:
  * No longer override the default CONFIG_SYS_TEXT_BASE setting.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2011-12-24 10:23:31 +01:00
Stefano Babic
92e30c07e0 ARM: omap3: add support to Technexion twister board
The twister board is a development board using
the TAM3517 SOM.

Support for NAND, 2 Ethernet (EMAC and SMC911),
USB (EHCI_OMAP).

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tapani Utrianen <tapani@technexion.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Sandeep Paulraj <s-paulraj@ti.com>
2011-12-24 10:23:29 +01:00
Wolfgang Denk
b96a661aea Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
  M28: Cleanup memsize.o OOT build
  i.MX28: Move SPL to arch/arm/cpu/arm926ejs/mx28
  M28: Fix typo
  M28: Document that units has to be set to sectors on SD bootcard
  i.mx: i.mx6q: add the initial support for i.mx6q ARM2 board
  i.mx: mxc_gpio: add the i.mx6q support
  i.mx: add the initial support for freescale i.MX6Q processor
  i.mx: introduce the armv7/imx-common folder
  S5PC2XX: Rename S5pc2XX to exynos
  tegra2: Don't use board pointer before it is set up
  tegra2: Remove unneeded 'dynamic ram size' message
  tegra2: Remove unused low-level Tegra2 UART code
  tegra2: Remove unneeded config option
  tegra2: Remove unneeded boot code
  tegra2: Enable instruction cache
  arm: Move CP15 init out of cpu_init_crit()
  tegra2: Simplify tegra_start() boot path
  tegra2: Add arch_cpu_init() to fire up Cortex-A9
  tegra2: Use new GPIO APIs in gpio_config_uart()
  tegra2: Add support for Ventana
  tegra2: Modify MMC driver to handle power and cd GPIOs
  tegra2: Move board_mmc_init into board files
2011-12-10 22:46:48 +01:00
Jason Liu
76d7f57449 i.mx: i.mx6q: add the initial support for i.mx6q ARM2 board
Add the initial support for Freescale i.MX6Q Armadillo2 board
Support: MMC boot from slot 0/1, debug UART(UART4), usdhc.

There is two MMC slots on the boards:
mmc dev 0 -> connect USDHC3 -> the lower slot on the board,
mmc dev 1 -> connect USDHC4 -> the upper slot on the board,

Signed-off-by: Jason Liu <jason.hui@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
2011-12-09 17:30:10 +01:00
Chander Kashyap
393cb36199 S5PC2XX: Rename S5pc2XX to exynos
As per new naming convention for Samsung SoC's, all Cortex-A9 and Cortex-A15
based SoC's will be classified under the name Exynos. Cortex-A9 and Cortex-A15
based SoC's will be sub-classified as Exynos4 and Exynos5 respectively.

In order to better adapt and reuse code across various upcoming Samsung Exynos
based boards, all uses of s5pc210 prefix/suffix/directory-names are renamed in
this patch. s5pc210 is renamed as exynos4210 and S5PC210/s5pc210 suffix/prefix
are renamed as exynos4/EXYNOS4.

Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2011-12-09 17:30:09 +01:00
Stephen Warren
d5ef19b9b3 tegra2: Add support for Ventana
Ventana is a board which is very similar to Seaboard. Support it by
re-using board/nvidia/seaboard/seaboard.c with minor run-time conditionals.

v5: Makefile: Use cmd_link_o_target, remove unused clean/distclean targets.
v6: Make gpio_config_uart_seaboard() static.
v7: Add MAINTAINERS entry for Ventana. Tom Warren doesn't have Ventana, so
    he asked me to add myself for this board.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2011-12-09 17:30:08 +01:00
Kyle Moffett
f8bbb4dad0 mpc85xx: Add board support for the eXMeritus HWW-1U-1A devices
The eXMeritus HWW-1U-1A unit is a DO-160-certified 13lb 1U chassis
with 3 independent TEMPEST zones.  Two independent P2020 computers may
be found inside each zone.  Complete hardware support is included.

High-level hardware overview:
  * DO-160 certified for passenger aircraft (noncritical)
  * TEMPEST ceritified for RED/BLACK separation
  * 3 zones per chassis, 2 computers per zone (total of 6)
  * Dual-core 1.066GHz P2020 per computer
  * One 2GB DDR2 SO-RDIMM module per computer (upgradable to 4GB)
  * Removable 80GB or 160GB Intel X18-M SSD per computer
  * Front-accessible dual-port E1000E per computer
  * Front-accessible serial console per computer
  * Front-accessible USB port per computer
  * Internal Gigabit crossover within each TEMPEST zone
  * Internal unidirectional fiber links across TEMPEST zones
  * Battery-backed DS1339 I2C RTC on each CPU.

Combined, each 13lb 1U chassis contains 12GB RAM, 12 cores @ 1.066GHz,
12 front-accessible Gigabit Ethernet ports and 960GB of solid-state
storage with a total power consumption of ~200W.

Additional notes:
  * SPD detection is only known to work with the DO-160-certified DIMMs

  * CPU reset is a little quirky due to hardware misfeature.  Proper
    support for the hardware reset mechanism has been left for a later
    patch series to address.

Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-12-09 08:40:12 -06:00
Wolfgang Denk
fb82fd7a32 MPC850: remove obsolete "rmu" Board
The "rmu" board has long been unmaintained, and is broken.
Remove it.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-12-08 20:51:39 +01:00
Wolfgang Denk
c53043b7f1 MPC7xx: remove obsolete "BAB7xx" board
The BAB7xx boards are almost deceased.  They cause build warnings, an
it's not worth the effort to fix these.  Remove the dead body.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Frank Gottschling <fgottschling@eltec.de>
2011-12-08 20:51:28 +01:00
Heiko Schocher
f7264c36cd arm, davinci: add support for am1808 based enbw_cmc board
- booting from NOR Flash with direct boot method
- POST support
- LOGBUF support

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Paulraj Sandeep <s-paulraj@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Christian Riesch <christian.riesch@omicron.at>
2011-12-06 23:59:37 +01:00
Marek Vasut
00c4acaa97 PXA: Drop CRADLE board
The board is unmaintained and maintainer doesn't respond.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Anatolij Gustschin <agust@denx.de>
2011-12-06 23:59:31 +01:00
Marek Vasut
f13eba66fd PXA: Drop CERF250 board
The board is unmaintained and maintainer doesn't respond.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Anatolij Gustschin <agust@denx.de>
2011-12-06 23:59:31 +01:00
Tim Schendekehl
14c3261497 Ethernut 5 board support
Add support for the Ethernut 5 open hardware design, based
on Atmel's AT91SAM9XE512 SoC.

V4
 - Fix several coding style issues.
 - Move machine type to config file.
 - Remove use of CONFIG_ATMEL_LEGACY.

Signed-off-by: Tim Schendekehl <tim.schendekehl@egnite.de>
2011-12-06 23:59:31 +01:00
Simon Guinot
5628fb75d1 ARM: add support for LaCie 2Big Network v2
This patch adds support for the LaCie 2Big Network v2 board, based on
the Marvell Kirkwood 6281 SoC.

Additional information is available at:
http://lacie-nas.org/doku.php?id=2big_network_v2

Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
2011-12-06 23:59:30 +01:00
Thomas Weber
e015edda7e OMAP3: Change devkit8000 maintainer
Signed-off-by: Thomas Weber <weber@corscience.de>
2011-12-06 22:12:21 +01:00
Nobuhiro Iwamatsu
6d1d5cf96e sh: Add support for ecovec board
The ecovec board has SH7724, 256MB DDR2-SDRAM, USB,
Ethernet, and more.

This patch supports the following functions:
	- 256MB DDR2-SDRAM
	- USB
	- I2C
	- Ethernet

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2011-12-02 13:46:22 +09:00
Wolfgang Denk
797449a16d Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx
* 'master' of git://git.denx.de/u-boot-ppc4xx:
  ppc4xx: Add Io64 board support
  ppc4xx: fix PMC440 painit command
  ppc4xx: remove invalid access to PCI_BRDGOPT2 register
  ppc4xx: use CONFIG_PCI_BOOTDELAY instead of private implementation
2011-12-02 00:03:08 +01:00
Dirk Eibach
255ef4d909 ppc4xx: Add Io64 board support
Board support for the Guntermann & Drunck Io64.

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2011-12-01 09:10:57 +01:00
Ira W. Snyder
9839709ea3 mpc85xx: support for Freescale COM Express P2020
This adds support for the Freescale COM Express P2020 board. This board
is similar to the P1_P2_RDB, but has some extra (as well as missing)
peripherals.

Unlike all other mpc85xx boards, it uses a watchdog timeout to reset.
Using the HRESET_REQ register does not work.

This board has no NOR flash, and can only be booted via SD or SPI. This
procedure is documented in Freescale Document Number AN3659 "Booting
from On-Chip ROM (eSDHC or eSPI)." Some alternative documentation is
provided in Freescale Document Number P2020RM "P2020 QorIQ Integrated
Processor Reference Manual" (section 4.5).

Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 09:07:51 -06:00
Stelian Pop
762e63754b Fix Stelian's email address
Change my old email address which is no longer valid.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-11-27 19:44:21 +01:00
Wolfgang Denk
6005ed55a9 Orphan EVB64260_750CX board
The last maintainer (Eran Man) cannot be reached any more.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-11-16 21:58:21 +01:00
Wolfgang Denk
0c2dd9a05b Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
  arm, davinci: add DAVINCI_MMC_CLKID
  arm, davinci_emac: fix driver bug if more then 3 PHYs are detected
  arm, davinci: da850/dm365 lowlevel cleanup
  omap5: Add omap5_evm board build support.
  omap4/5: Add support for booting with CH.
  omap5: emif: Add emif/ddr configurations required for omap5 evm
  omap5: clocks: Add clocks support for omap5 platform.
  omap5: Add minimal support for omap5430.
  omap: Checkpatch fixes
  omap4: make omap4 code common for future reuse
  GCC4.6: Squash warnings in onenand_base.c
  GCC4.6: Fix common/usb.c on xscale
  OneNAND: Add simple OneNAND SPL
  PXA: vpac270: Enable the new generic MMC driver
  PXA: Cleanup serial_pxa
  PXA: Drop csb226 and innokom boards (unmaintained)
  m28evk: Fix comment about the number of RAM banks
  mx31: Fix checkpatch warnings in generic.c
  mx31: Use proper IO accessor for GPR register
  mx31: Remove duplicate definition for GPR register
  qong: Use generic function for configuring GPR register
  M28EVK: Enable USB HOST support
  iMX28: Add USB HOST driver
  iMX28: Add USB and USB PHY register definitions
  M28: Add memory detection into SPL
  iMX28: Fix ARM vector handling
  M28: Add doc/README.m28 documentation
  M28: Add MMC SPL
  iMX28: Add support for DENX M28EVK board
  iMX28: Add u-boot.sb target to Makefile
  iMX28: Add image header generator tool
  iMX28: Add driver for internal RTC
  iMX28: Add GPMI NAND driver
  iMX28: Add APBH DMA driver
  iMX28: Add SPI driver
  iMX28: Add GPIO control
  iMX28: Add I2C bus driver
  iMX28: Add PINMUX control
  FEC: Add support for iMX28 quirks
  iMX28: Add SSP MMC driver
  iMX28: Initial support for iMX28 CPU
  MX25: zmx25: GCC4.6 fix build warnings
  da850: add new config file for AM18xx
  BeagleBoard: config: Switch to ttyO2
  OMAP3: Change omap3_evm maintainer
  devkit8000: Fix NAND SPL on boards with 256MB NAND
  integrator: enable Vpp and disable flash protection
  integrator: add system controller header
  integrator: make flash writeable on boot
  integrator: use io-accessors for board init
  integrator: move text offset to config
  integrator: pass configs for core modules
  ARM: remove superfluous setting of arch_number in board specific code.
  SPL: Allow ARM926EJS to avoid compiling in the CPU support code
  integrator: do not test first part of the memory
  arm: a320: fix broken timer
  ARM: define CONFIG_MACH_TYPE for all ronetix boards
  dm646x: pass board revision info to kernel
  dm646x: add new configuration for dm6467T
  arm, davinci: Fix setting of the SDRAM configuration register
  arm, davinci: Remove the duplication of LPSC functions
  arm, davinci: Rename AM1808 lowlevel functions to DA850
  da8xxevm: fix build error
  ARM: re-add MACH_TYPE_XXXXXX for VCMA9 board and add CONFIG_MACH_TYPE
2011-11-16 20:24:41 +01:00
Sricharan
508a58fa8e omap5: Add minimal support for omap5430.
This patch adds the minimal support for OMAP5. The platform and machine
specific headers and sources updated for OMAP5430.

OMAP5430 is Texas Instrument's SOC based on ARM Cortex-A15 SMP architecture.
It's a dual core SOC with GIC used for interrupt handling and SCU for cache
coherency.

Also moved some part of code from the basic platform support that can be made
common for OMAP4/5. Rest is kept out seperately. The same approach is followed
for clocks and emif support in the subsequent patches.

Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15 22:25:50 +01:00
Marek Vasut
dd36d806fe PXA: Drop csb226 and innokom boards (unmaintained)
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Robert Schwebel <robert@schwebel.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-11-15 22:24:50 +01:00
Marek Vasut
fc10272856 iMX28: Add support for DENX M28EVK board
This contains support for the following components:
- DUART
- MMC
- Both FEC interfaces
- NAND
- I2C (RTC, EEPROM)
- SPI (FLASH)

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
2011-11-11 11:36:57 +01:00
Tom Rini
15fef52b9f OMAP3: Change omap3_evm maintainer
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-10 16:30:41 +01:00
Macpaul Lin
51b03637b8 adp-ag101p: add product into MAINTAINERS list
Add ADP-AG101P into MAINTAINERS list.
Add ADP-AG101P into boards.cfg.

Signed-off-by: Macpaul Lin <macpaul@andestech.com>
2011-11-10 10:46:54 +08:00
Michael Jones
84d7a0171f OMAP3: mvblx: Initial support for mvBlueLYNX-X
Add support for the MATRIX VISION mvBlueLYNX-X, an OMAP3-based
intelligent camera.

Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-04 13:54:33 -04:00
Heiko Schocher
4dd834906d arm, davinci: add cam_enc_4xx support
- DM368 SOC
- booting with spl not with UBL from TI
- before loading u-boot from NAND into RAM, test
  the RAM with the post memory test. If error
  is found, switch all LEDs on and halt system.
- SPI Flash
  Dataflash Typ: M25PE80
- Ethernet DM9161BI
- MMC
- USB

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03 22:56:25 +01:00
Helmut Raiger
4d86dd022e mx31: Add board support for HALE TT-01
This adds basic board support for TT-01 based on
the Bluetechnix i.MX31 SOM. Currently only NOR-Flash
boot is implemented.

Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Acked-by: Stefano Babic <sbabic@denx.de>
2011-11-03 22:56:20 +01:00
Stefano Babic
deb53483df MX35: add support for flea3 board
The flea3 board is a custom board by CarMediaLab used
in automotive.
Network (FEC), NOR, NAND and SPI are supported.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2011-11-03 22:56:20 +01:00
Rob Herring
37fc0ed268 ARM: Add Calxeda Highbank platform
Add basic support for Calxeda Highbank platform. Only minimal support with
serial and SATA are included.

Signed-off-by: Jason Hobbs <jason.hobbs@calxeda.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-10-27 21:56:37 +02:00
Chandan Nath
5289e83a8c ARM:AM33XX: Add support for TI AM335X EVM
This patch adds basic support for booting the board.
This patch adds support for the UART necessary to
get to the u-boot prompt.

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-10-27 21:56:36 +02:00
Jason Cooper
2e0c1c7d5c dreamplug: initial board support.
Copied wholeheartedly from board/Marvell/guruplug and modified to add support
for SPI NOR flash.

CONFIG_MACH_DREAMPLUG defined in include/configs/dreamplug.h until Linus's
kernel.org tree adds it to mach-types.h.  Once it trickles down, the definition
can be removed from include/configs/dreamplug.h.

Signed-off-by: Jason Cooper <u-boot@lakedaemon.net>
2011-10-27 21:56:32 +02:00
Wolfgang Denk
e877fabeb9 MPC85xx: remove broken "mpq101" board
The board stopped building some time ago, and the board maintainer
agrtees to drop it - see
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/112674

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
2011-10-23 17:00:47 +02:00
Macpaul Lin
5f1719c105 adp-ag101: add board adp-ag101 support
Add evaluation board "adp-ag101" configuration file adp-ag101.h.
Add adp-ag101.c board config and related settings.
Add board adp-ag101 into boards.cfg

Signed-off-by: Macpaul Lin <macpaul@andestech.com>
2011-10-22 00:54:25 +02:00
Xiangfu Liu
3c945542da MIPS: Jz4740: Add qi_lb60 board support
Add support for the qi_lb60 (a.k.a QI Ben NanoNote) clamshell device
from Qi hardware:

http://en.qi-hardware.com/wiki/Ben_NanoNote
http://en.qi-hardware.com/wiki/Main_Page
http://en.wikipedia.org/wiki/Qi_hardware

This Jz4740-based clamshell device does not use NOR flash to boot.
The initial bring-up assumes that U-Boot is directly loaded into SDRAM
using USB boot tool, and starts from 0x80100000.

About USB boot tool
-------------------

Jz4740 is one of the XBurst processors with USB boot functionality
supported.  The CPU can boot from a small ROM in the LSI, initialize
CPU and USB module, then wait for USB commands from the USB host.
We can send 8 KB binary data to the CPU cache using USB boot tool.

USB boot tool is available to the public at Ingenic website.  Also
there is an alternative Debian package named xburst-tools.

Signed-off-by: Xiangfu Liu <xiangfu@openmobilefree.net>
Acked-by: Daniel <zpxu@ingenic.cn>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
2011-10-12 23:28:49 +09:00
Paul Gortmaker
b30d41cad6 sbc82xx: delete support for obsolete SBC8240/SBC8260
The EST SBC8260 is over 10 years old, and the SBC8240 older than
that.  With the tiny amount of RAM (by today's standards), there
really isn't anyone interested in running the latest U-boot on
these EOL products anymore.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: jon.diekema@smiths-aerospace.com
2011-10-01 21:57:13 +02:00
Paul Gortmaker
2c32003a5e MAINTAINERS: delete stale entry for EOL Wind River boards
This e-mail address is no longer valid, and the boards are long
since EOL.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-01 21:56:47 +02:00
Marek Vasut
0ef4fc533a EfikaMX: Add imximage config for Efika SB
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
2011-09-30 22:01:06 +02:00
Fabio Estevam
419adbfbcb MX25: Add initial support for MX25PDK
Add the initial support for MX25PDK booting from SD card via internal boot.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-09-30 22:01:00 +02:00
Aneesh V
e1149a629a omap4: update maintainer for omap4 boards
Steve wants to transfer maintainership of OMAP4 boards
to me as he is not working on these boards lately.

CC: Steve Sakoman <steve@sakoman.com>
CC: Sandeep Paulraj <s-paulraj@ti.com>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
CC: Wolfgang Denk <wd@denx.de>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30 22:00:55 +02:00
Albert ARIBAUD
0ca8eb7137 ARM: remove broken "ixdp425" and "ixpdg425" boards
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Stefan Roese <sr@denx.de>
2011-09-27 08:58:04 +02:00
Wolfgang Denk
5df092d781 ARM: remove broken "shannon" board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Rolf Offermanns <rof@sysgo.de>
2011-09-07 21:46:40 +02:00
Wolfgang Denk
9c62815bf7 ARM: remove broken "modnet50" board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Thomas Elste <info@elste.org>
2011-09-07 21:46:40 +02:00
Wolfgang Denk
3d57573986 ARM: remove broken "lart" board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Alex Züpke <azu@sysgo.de>
2011-09-07 21:46:40 +02:00
Wolfgang Denk
c1f8750f9f ARM: remove broken "impa7" board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Marius Gröger <mag@sysgo.de>
2011-09-07 21:46:40 +02:00
Wolfgang Denk
2c650e2010 ARM: remove broken "gcplus" board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: George G. Davis <gdavis@mvista.com>
2011-09-07 21:46:40 +02:00
Wolfgang Denk
c8f63b415f ARM: remove broken "ep7312" board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Marius Gröger <mag@sysgo.de>
2011-09-07 21:46:39 +02:00
Wolfgang Denk
fc5e5ceec4 ARM: remove broken "dnp1110" board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Alex Züpke <azu@sysgo.de>
2011-09-07 21:46:39 +02:00
Linus Walleij
0789dc14d2 MAINTAINERS: fix integrator and versatile
- Take maintainership of the integratorcp board
- Remove the double entry for the versatile board
  it has two variants but only one board folder

Cc: Philippe Robin <philippe.robin@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-09-04 23:24:18 +02:00
Chander Kashyap
b9a1ef219e ARMV7: Add support for Samsung ORIGEN board
Origen board is based upon S5PV310 SoC which is similiar to
S5PC210 SoC.

Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2011-09-04 11:36:15 +02:00
Wolfgang Denk
b550834458 ARM: remove broken "at91cap9adk" board
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stelian Pop <stelian.pop@leadtechdesign.com>
2011-09-04 11:36:14 +02:00
Wolfgang Denk
ad218a868b ARM: remove broken "smdk2400" board
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Gary Jennejohn <garyj@denx.de>
2011-09-04 11:36:14 +02:00
Wolfgang Denk
5dcf53696f ARM: remove broken "B2" board
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andrea Scian <andrea.scian@dave-tech.it>
2011-09-04 11:36:13 +02:00
Wolfgang Denk
be28857072 ARM: remove broken "armadillo" board
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Rowel Atienza <rowel@diwalabs.com>
2011-09-04 11:36:13 +02:00
Wolfgang Denk
c91e90db8c ARM: remove broken "assabet" board
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: George G. Davis <gdavis@mvista.com>
2011-09-04 11:36:13 +02:00
Phil Edworthy
7fbeb6422d sh: Add Renesas rsk7264 board
The rsk7264 (also know as rsk2+sh7264) is an SH2A based board
with 64MB NAND flash and 64MB SDRAM. It is very similar to the
rsk7203 board.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2011-08-22 13:16:08 +09:00
Albert ARIBAUD
fa82f871c8 Convert ISO-8859 files to UTF-8
There was a mix of UTF-8 and ISO-8859 files in the U-Boot source
tree, which could cause issues with the patchwork review system.
This commit converts all ISO-8859 files to UTF-8.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-08-04 23:34:02 +02:00
Ajay Bhargav
26749582d5 Armada100: Add Board Support for Marvell GuruPlug-Display
This patch adds basic board support with DRAM and UART functionality

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
Acked-by: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com>
2011-08-04 19:00:32 +02:00
Andreas Bießmann
ad7a1785f7 avr32: add grasshopper (ICnova AP7000) board
The grasshopper board is a neat avr32 evaluation kit produced by In-Circuit
GmbH.
See http://www.ic-board.de/product_info.php?info=p75_ICnova-AP7000-Base.html
for detailed information about this device.

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2011-08-03 13:00:56 +02:00
Niklaus Giger
1103cf2f5c Removed obsolete Netstal boards
Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
2011-07-28 21:45:34 +02:00
Linus Walleij
b9af6d3d82 MAINTAINERS: integrator+versatile boards
- Take maintainership of the unlisted integratorap board
- Orphan the boards maintained by Peter Pearse, as he has retired
  from ARM

Cc: Philippe Robin <philippe.robin@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-07-28 16:50:37 +02:00
Matthias Weisser
39f0023e81 imx: Add support for zmx25 board
zmx25 is a board based on imx25 SoC, 64 Megs of LPDDR, 32 Megs of NOR flash, an
optional NAND flash.

Signed-off-by: Matthias Weisser <weisserm@arcor.de>
2011-07-14 15:41:24 +02:00
Torsten Koschorrek
81d668ea90 ARM: Update maintainer of board scb9328
Signed-off-by: Torsten Koschorrek <koschorrek@synertronixx.de>
2011-07-14 15:41:24 +02:00
Roy Zang
3f7f6b8592 powerpc/85xx: Add basic support for P1023RDS board
The P1023RDS board is the reference board for the P1023 SoC.

Add support for booting it from NOR or NAND, with fixed 2G of DDR, PCIe,
UART, I2C, etc.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-11 13:24:20 -05:00
Andre Schwarz
7fb3e7a2d6 mpc83xx: Add support for MergerBox board
Includes board config file, documentation, maintainer and boards.cfg
entries, and board specific files in vendor dir.

Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-07-06 19:09:27 -05:00
Simon Guinot
79642098a8 Add support for Network Space v2 and parents
This patch add support for the Network Space v2 board and parents, based
on the Marvell Kirkwood 6281 SoC. This include Network Space (Max) v2
and Internet Space v2.

Additional information is available at:
http://lacie-nas.org/doku.php?id=network_space_v2

Signed-off-by: Simon Guinot <sguinot@lacie.com>
2011-07-04 10:55:28 +02:00
Valentin Longchamp
01fa4e8cde arm/km: add support for portl2 board
This adds support for the keymile Kirkwood BEC portl2 board. This board
relies on the km_arm (km_kirkwood) BEC.

The egiga driver is configured for a 100M full-duplex, A/N off connnection
to the backplane. This board has always ethernet present, because it is
connected to the marvell switch similar to mgcoge3un. The reset_phy
functionality is also the same to mgcoge3un.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Heiko Schocher <hs@denx.de>
2011-07-04 10:55:28 +02:00
Holger Brunck
83b40c3146 arm/km: replace suenx targets with km_kirkwood
suen3 and suen8 were in first HW version quite different, but
now they are from a u-boot point of view similar. So these
two boards can use the same header file. Other keymile boards
differ only in the usage of the PCI interface. Therefore
a target km_kirkwood_pci was introduced. All targets use
the same header file.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Heiko Schocher <hs@denx.de>
2011-07-04 10:55:28 +02:00
Fabio Estevam
47c3e074ad MX53: Add initial support for MX53ARD
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-07-04 10:55:26 +02:00
Wolfgang Denk
9623c158f6 Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
  run arm_pci_init after relocation
  IXP42x PCI rewrite
  update/fix PDNB3 board
  update/fix IXDP425 / IXDPG425 boards
  add dvlhost (dLAN 200 AV Wireless G) board
  IXP NPE: add support for fixed-speed MII ports
  update/fix AcTux4 board
  update/fix AcTux3 board
  update/fix AcTux2 board
  update/fix AcTux1 board
  use -ffunction-sections / --gc-sections on IXP42x
  support CONFIG_SYS_LDSCRIPT on ARM
  fix "depend" target in npe directory
  Fix IXP code to work after relocation was added
  trigger hardware watchdog in IXP42x serial driver
  add support for IXP42x Rev. B1 and newer
  add XScale sub architecture (IXP/PXA) to maintainer list

Conflicts:
	arch/arm/lib/board.c

Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-06-23 15:37:33 +02:00
Michael Schwingen
10c9787e68 add dvlhost (dLAN 200 AV Wireless G) board
Signed-off-by: Michael Schwingen <michael@schwingen.org>
2011-06-23 08:25:18 +02:00
Michael Schwingen
c3dc3dfb7e add XScale sub architecture (IXP/PXA) to maintainer list
Signed-off-by: Michael Schwingen <michael@schwingen.org>
2011-06-23 08:24:55 +02:00
Wolfgang Denk
566e5cf451 ARM: drop unsupported 'trab' board
The 'trab' board configuration is broken, and there is nobody who is
interested and willing to fix it.  Drop it.

This includes support for VFD displays which have always been used by
this board only.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-06-22 20:00:51 +02:00
Ryan Mallon
b8d41dda22 Add support for Bluewater Systems Snapper 9260/9G20 modules
Add support for Bluewater Systems AT91 based Snapper 9260 and 9G20
single board computer modules. Includes NAND flash and Ethernet
support.

Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
2011-06-21 22:26:21 +02:00
Wolfgang Denk
1a0787d3c4 Merge branch 'master' of /home/wd/git/u-boot/custodians
* 'master' of /home/wd/git/u-boot/custodians:
  SMDKV310: Fix incorrect conditional compilation for MIU linear mapping
  SMDKV310: CPU fequency and mmc_pre_ratio modified
  armv7: Add support for ST-Ericsson U8500 href platform
  I2C: Add driver for ST-Ericsson U8500 i2c
  armv7: Add ST-Ericsson u8500 arch
  Kirkwood: boards cleanup for deprecated CONFIG_CMD_AUTOSCRIPT
  ARMV7: Vexpress: Add missing MMC header
  arm/km: update mgcoge3un board support
  mvgbe: enable configurability of PORT_SERIAL_CONTROL_VALUE
  arm/km: rename mgcoge2un to mgcoge3un
  arm/km: add second serial interface for kirkwood
  arm/km: disable ls (through jffs2 support)
  arm/km: introduce bootcount env variable and clean km_arm
  arm/km: move CONFIG_EXTRA_ENV_SETTINGS from board to km_arm file
  arm/km: remove CONFIG_SYS_KWD_CONFIG from keymile-common.h
  ARMV7: MMC SPL Boot support for SMDKV310 board
  ARMV7: Add support for Samsung SMDKV310 Board
  S5PC2XX: clock: support pwm clock for evt1 (cpu revision 1)
  S5P: add set_mmc_clk for external clock control
  S5PC2XX: Support the cpu revision
  S5P:SROM config code moved to s5p-common directory
  Add _end for the end of u-boot image for SMDK6400
  MMC S5P: Fix typo
  S5P: GPIO Macro Values Corrected.
  SMDK2410: various cleanup/code style fixes
  SMDK2410: use the CFI driver (and remove the old one)
  SMDK2410: remove unneeded config.mk
  SMDK2410: activate ARM relocation feature
  BeagleBoard: fixed typo in typecast
  mvsata: issue hard reset on initialization
  VCMA9: use ARM relocation feature to fix build error
  MX31: drop warnings due to missing prototype for mxc_watchdog_reset()
  MX5: drop config.mk from efikamx board
  MX31: Make get_reset_cause() static and drop unreachable code
  MX53: Remove CONFIG_SYS_BOOTMAPSZ from mx53 config files.
  MX53: Handle silicon revision 2.1 case
  mx5: board: code clean up for checkboard code
  MX51: vision2: Fix build for vision2 board.
  MX51: vision: Let video mode struct be independant of watchdog.
  MX53: Add initial support for MX53SMD board.
  MX53: support for freescale MX53LOCO board
  mx5: Fix CONFIG_OF_LIBFDT redefined warning
  mx5: Remove unnecessary CONFIG_SYS_BOOTMAPSZ definition
  mx31pdk: Clean up mx31pdk.h file
2011-06-01 22:04:29 +02:00
Marek Vasut
9f084b1e04 Move wepep250,delta,xsengine to scrapyard
Drop wepep250 board from MAINTAINERS and add all these three boards to
doc/README.scrapyard

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2011-06-01 21:53:57 +02:00
Valentin Longchamp
68d6963c44 arm/km: rename mgcoge2un to mgcoge3un
The mgcoge2un target was only an intermediate step to mgcoge3un.
For this reason the mgcoge2un support was moved to mgcoge3un,
because it isn't needed to support both targets.

We add the BootROM init file for the mgcoge3un memphis RAM.

We also move the suen3 and suen8 boards into the correct category
in the MAINTAINERS file.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
2011-05-31 19:45:59 +02:00
Chander Kashyap
e21185bae6 ARMV7: Add support for Samsung SMDKV310 Board
SMDKV310 board is based on Samsung S5PV310 SOC. This SOC is very much
similar to S5PC210.

Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2011-05-26 19:33:44 +09:00
Fabio Estevam
860b32ee50 MX53: Add initial support for MX53SMD board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-05-23 08:36:46 +02:00
Jason Liu
938080dc4b MX53: support for freescale MX53LOCO board
This patch add initial support for freescale MX53LOCO board.
Network(FEC),SD/MMC,UART have been supported by this patch

Signed-off-by: Jason Liu <jason.hui@linaro.org>
2011-05-23 08:36:46 +02:00
Holger Brunck
489337f513 powerpc/km82xx: add mgcoge3ne and remove mgcoge2ne support
This patch adds support for the MPC8247 based board mgcoge3ne.
Additionaly mgcoge2ne board supprot was removed, because due
to the mgcoge3ne, this board is obsolete and not longer
maintained.
The board is similar to mgcoge. The difference is that
a NUMONYX flash is used and a different SDRAM (256MB).
Also introduce CONFIG_KM_82XX to collect ppc82xx common
settings and remove staticness from the common set_pin function.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
2011-05-10 22:48:50 +02:00
Heiko Schocher
4074296b1c powerpc, 83xx: add kmsupx5 board support
The Keymile SUPx5 board series is based on a PBEC8321 but
contains an additional PBUS FPGA (LPXF) on local bus CS2.

Signed-off-by: Thomas Reufer <thomas.reufer@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
2011-04-30 00:44:53 +02:00
Heiko Schocher
af895e4527 ppc: add support for ppc based board mgcoge2ne
The mgcoge2 board from keymile deploys two different processors.
An ARM based Kirkwood for the "unit" part of the SW and a PPC for
the "ne" part of the SW. Therefore in Linux and U-Boot the names
for the board are mgcoge2un and mgcoge2ne. This patch adds the
mgcoge2ne part of the board. The ppc part of mgboge2 is quite
similar to mgcoge, therefore a generic header km82xx-common.h
was introduced to collect all similiarities. Currently the only
difference is that mgcoge2ne has a 64 MB numonyx NOR flash with
a single die. The mgcoge has a dual die flash 2*32MB from spansion.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
2011-04-30 00:44:47 +02:00
Heiko Schocher
effe5e8cda arm: add support of Kirkwood based board SUEN8
The Kirwood based SUEN8 board from Keymile is at this stage
the same than the suen3 board. This patch adds the board
support for the suen8.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
2011-04-30 00:44:44 +02:00
Heiko Schocher
331a30dc5b arm: add support for kirkwood based mgcoge2un board
This board is similar to keymile suen3.

Signed-off-by: Clive Stubbings <clive.stubbings@xentech.co.uk>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
2011-04-30 00:44:39 +02:00
Heiko Schocher
dc6033ecf1 mpc832x: add support for mpc8321 based tuda1 board
This board is similar to suvd3 board. So most initialisation topics
are taken from suvd3 (UART1, Ethernet, piggy PHY, flash, ram) only the
application specific chip selects differ.

Signed-off-by: Lukas Roggli <lukas.roggli@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
2011-04-30 00:44:37 +02:00
Heiko Schocher
9a276bb093 mpc832x: add support for mpc8321 based tuxa1 board
This board is similar to suvd3 board. So most initialisation topics
are taken from suvd3 (UART1, Ethernet, piggy PHY, flash, ram) only the
application specific chip selects differ.

Signed-off-by: Lukas Roggli <lukas.roggli@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
2011-04-30 00:44:35 +02:00
Heiko Schocher
62ddcf05e7 mpc832x: add support for the mpc8321 based suvd3 board
- serial console on UART1
- Ethernet RMII over UCC4
- PHY SMSC LAN8700
- 64MB Flash
- 128 MB DDR2 RAM
- I2C
- bootcount

This board is similiar to the kmeter1 (8360) board,
so common config options are extracted into the
include/configs/km83xx-common.h file.

Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
2011-04-30 00:44:29 +02:00
Luca Ceresoli
fb6e1f1b9d ARMV7: OMAP3: Add support for Comelit DIG297 board
Board support for the DIG297 board manufactured by Comelit Group SpA.
It is a custom board based on the BeagleBoard <http://beagleboard.org/> by
Texas Instruments.

The board support is based on the BeagleBoard implementation.

Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-04-27 19:38:10 +02:00
Albert ARIBAUD
57b4bce996 Replace obsolete e-mail address
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-04-27 19:38:09 +02:00
Igor Grinberg
31dd52f74d OMAP3: CM-T35: update MAINTAINERS file
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-04-27 19:38:06 +02:00
Srinath
915162daaa ARMV7: AM3517/05: Add support for CraneBoard.
It is a low cost reference design based on Sitara AM3517 SoC from Texas Instruments
Please refer to <www.craneboard.org> for more details.

Signed-off-by: Srinath <srinath@mistralsolutions.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-04-27 19:38:06 +02:00
Fabio Estevam
73e5476e1e MAINTAINERS: fix email address case
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-04-13 22:40:51 +02:00
Graeme Russ
b3acbb221d x86: Update MAINTAINERS and delete README files
The README files are totally out-of-date to the point where they do more
harm than good

Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
2011-04-13 19:43:30 +10:00
Mike Frysinger
7577aab8a6 Blackfin: bf506f-ezkit: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08 00:44:26 -04:00
Chong Huang
dbb6d366e3 Blackfin: bf525-ucr2: new board port
Signed-off-by: Chong Huang <chuang@ucrobotics.com>
Signed-off-by: Haitao Zhang <minipanda@linuxrobot.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08 00:44:26 -04:00
Andreas Schallenberg
2fc32deab5 Blackfin: dnp5370: new board port
Info about the hardware can be found here:
	http://www.dilnetpc.com/dnp0086.htm

Signed-off-by: Andreas Schallenberg <Andreas.Schallenberg@3alitydigital.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08 00:44:26 -04:00
Daniel Schwierzeck
b38a569901 MIPS: Purple: Remove Purple support
The Purple SoC and eval board are not actively maintained since years.
This patch removes the support completely as aggreed with Wolfgang Denk.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
2011-04-02 22:07:12 +09:00
Lei Wen
ea4bc120db Pantheon: Add Board Support for Marvell dkb board
DKB is a Development Board for PANTHEON TD/TTC(pxa920/pxa910) with
* Processor upto 806Mhz
* LPDDR1/2
* x8/x16 SLC/MLC NAND
* Footprints for eMMC & MMC x8 card

With Peripherals:
* Parallel LCD I/F
* Audio codecs (88PM8607)
* MIPI CSI-2 camera
* Marvell 88W8787 802.11n/BT module
* Marvell 2G/3G RF
* Dual analog mics & speakers, headset jack, LED, ambient
* USB2.0 HS host, OTG (mini AB)
* GPIO, GPIO expander with DIP switches for easier selection
* UART serial over USB, CIR

This patch adds basic board support with DRAM and UART functionality

Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2011-02-21 08:30:55 +01:00
Tom Warren
ee4bbbcb65 arm: Tegra2: Add support for NVIDIA Seaboard board
Signed-off-by: Tom Warren <twarren@nvidia.com>
2011-02-21 08:30:55 +01:00
Tom Warren
efc05ae131 arm: Tegra2: Add support for NVIDIA Harmony board
Signed-off-by: Tom Warren <twarren@nvidia.com>
2011-02-21 08:30:55 +01:00
Wolfgang Denk
fced09ae38 Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx 2011-02-09 20:50:26 +01:00
Dirk Eibach
2da0fc0d0f ppc4xx: Add DLVision-10G board support
Board support for the Guntermann & Drunck DLVision-10G.
Adds support for multiple FPGAs per board for gdsys 405ep
architecture.
Adds support for dual link osd hardware for gdsys 405ep.

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2011-02-07 11:13:16 +01:00
Wolfgang Denk
4bfa18fb99 Merge branch 'master' of git://git.denx.de/u-boot-sh 2011-02-04 20:38:27 +01:00
Wolfgang Denk
be9db564de Merge branch 'master' of /home/wd/git/u-boot/custodians 2011-02-02 21:57:19 +01:00
Yoshihiro Shimoda
c9cb009560 change email address in MAINTAINERS
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
2011-02-02 21:30:43 +01:00
Yoshihiro Shimoda
9274b7b2ea change email address in MAINTAINERS
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2011-02-02 16:38:42 +09:00
Yoshihiro Shimoda
8e9c897b21 sh: add support for sh7757lcr board
The R0P7757LC0030RL board has SH7757, 256MB DDR3-SDRAM, SPI ROM,
Ethernet, and more.

This patch supports the following functions:
 - 256MB DDR3-SDRAM
 - SPI ROM
 - Ethernet

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2011-02-02 16:38:41 +09:00
Minkyu Kang
9e40808c3f armv7: add support for s5pc210 universal board
This patch adds support for Samsung s5pc210 universal board

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2011-02-02 00:54:45 +01:00
Mike Rapoport
36b4e2dddd OMAP3: add CM-T35 board
This patch adds support for CM-T35 board

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-02-02 00:54:43 +01:00
Stefano Babic
eae4988b45 Add support for Freescale's mx35pdk board.
The patch adds suupport for the Freescale's mx35pdk board
(known as well as mx35_3stack).

The board boots from the NOR flash. Following devices
are supported:
 - two ethernet devices (FEC and SMC911x on debug board)
 - I2C
 - PMIC (MC13892) via I2C interface
 - UART
 - NOR flash (64MB)
 - NAND flash (2GB)
 - basic access to mc9sdz60 registers via I2C interface

Signed-off-by: Stefano Babic <sbabic@denx.de>
2011-02-02 00:54:43 +01:00
Marek Vasut
d59140170a iMX5: EfikaMX: Preliminary board support
Supported:
MMC
IDE
PMIC
SPI flash
LEDs

I can boot the kernel supplied by freescale/genesi with this from MMC card
and/or PATA disk.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2011-02-02 00:54:42 +01:00
Liu Hui-R64343
94391fbcee MX5:MX53: add initial support for MX53EVK board
Add initial support for MX53EVK board support.
FEC, SD/MMC, UART, I2C, have been supported.

Signed-off-by: Jason Liu <r64343@freescale.com>
2011-02-02 00:54:42 +01:00
Alex Dubov
a14a94469c mpq101: initial support for Mercury Computer Systems MPQ101 board
Mpq101 is a RapidIO development board in AMC form factor, featuring MPC8548
processor, 512MB of hardwired DDR2 RAM, 128MB of hardwired NAND flash
memory, real time clock and additional serial EEPROM on i2c bus (enabled).
USB controller is available, but not presently enabled.

Additional board information is available at:
http://www.mc.com/products/boards/ensemble_mpq101_rapidio_powerquicc_iii.aspx

Environment is configured to precede the actual u-boot image so that it's
located at the beginning of flash erase block (made necessary by the recent
changes to the embedded environment handling). This is achieved by means of
custom ld script.

Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-26 23:44:00 -06:00
Heiko Schocher
466f0137e8 mpc5200, digsy_mtc: add support for rev5 board version
difference to previous board version:
- M29W128GH flash from Numonyx
- SDRAM ISSI IS45S16800 (Option A2 105°C)
- rev5 uses RTC RV-3029-C2
- update cs0 and cs1 baseaddr and length
  depending on the detected flash size.
- added Werner Pfister <Pfister_Werner@intercontrol.de>
  as maintainer for the digsy board variants
- As the M29W128GH needs a special flash_cmd_reset()
  document that in the new file doc/README.cfi.
- move "#endif /* CONFIG_CMD_IDE */" to the right place
- remove LOWBOOT config option for digsy_mtc and digsy_mtc_rev5
  boards
- change doc/README.cfi as Stefan Roese suggested

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
cc: Wolfgang Denk <hs@denx.de>
cc: Stefan Roese <sr@denx.de>
cc: Werner Pfister <Pfister_Werner@intercontrol.de>
cc: Detlev Zundel <dzu@denx.de>
2011-01-18 23:34:26 +01:00
Holger Brunck
1514579fbf ppc, 8xx: remove obsolete km8xx boards from keymile
The MPC852 based mgsuvd and kmsupx4 boards from keymile
were initially ported but later on not developed further. So
the respective files were removed to avoid unneeded merging
and maintenance.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher<hs@denx.de>
2011-01-18 23:30:16 +01:00
Paul Gortmaker
f2cdf461b6 MPC8xxx: Update maintainer entry for Wind River sbc8xxx boards
I've probably got the best chance of getting access to these
boards in order to test things, and since Joe's e-mail is
bouncing, update the MAINTAINERS entry to reflect this.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:17 -06:00
Kumar Gala
d761fa6205 powerpc/85xx: Removed support for ATUM8548 board
The ATUM8548 board is no longer maintained and thus we are removing
support for it.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:17 -06:00
Nobuhiro Iwamatsu
6b7c0f5ebf sh: Add support shmin board
This adds support for the SHMIN SH7706 board(T-SH7706LAN).
The CPU of this board is SH7706.
There are SDRAM of 32M byte, Flash memory of 512K byte, Serial,
10Base Ether and MMC.

http://web.kyoto-inet.or.jp/people/takagaki/T-SH7706/T-SH7706.htm

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2011-01-11 21:03:25 +09:00
Mike Frysinger
3474741c8d MAINTAINERS: sort Blackfin entries
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-01-09 21:06:48 +01:00
Simon Kagstrom
2f3845199f MAINTAINERS: Transfer openrd_base maintainership to Prafulla Wadaskar
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
2010-12-16 23:03:08 +01:00
Prafulla Wadaskar
c291e2fc41 Armada100: Add Board Support for Marvell Aspenite-DB
Aspenite is a Development Board for ASPEN/ARMADA168(88AP168) with
	* Processor upto 1.2GHz
        * Parallel 1Gb x8 DDR2-1066 MHz
        * 16 Mb x16 NOR, 4Gb x8 SLC NAND, footprint for SPI NOR
        * Footprints for eMMC/eSD NAND & MMC x8 card
        * 4-in-1 card reader (xD, MMC/SD/MS Pro), CF True IDE socket
        * SEAF memory board, subset of PISMO2
    With Peripherals:
        * 4.3” WVGA 24-bit LCD
        * Audio codecs (AC97 & I2S), TSI
        * VGA camera
        * Video in via 3 RCA jacks, and HDMI type C out
        * Marvell 88W8688 802.11bg/BT module
        * GPS RF IC
        * Dual analog mics & speakers, headset jack, LED, ambient light sensor
        * USB2.0 HS host  (A), OTG (micro AB)
        * FE PHY, PCIE Mini Card  slot
        * GPIO, GPIO expander with DIP switches for easier selection UART serial over USB, CIR

This patch adds basic board support with DRAM and UART functionality
The patch is tested for boot from DRAM using XDB

Signed-off-by: Mahavir Jain <mjain@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2010-12-16 23:03:05 +01:00
Wolfgang Denk
006915fbb0 Merge branch 'master' of ../master into next 2010-12-16 23:00:53 +01:00
Heiko Schocher
98e6956702 mpc52xx: add support for tqm52xx based board charon
- serial console in PSC1
- 128MiB DRAM
- 32MiB Flash
- FEC Ethernet
- 2 I2C busses
- FPGA on CS3
- IDE
- VGA SMI501

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-12-16 22:58:59 +01:00
Reinhard Meyer
d55c5c3f81 AT91: add TOP9000 support
Adds support for the EMK TOP9000 CPU Module which is
based on ATMELs ARM926EJS AT91SAM9XE SoC.

Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-12-07 16:36:41 +01:00
Stefano Babic
649a33e434 Davinci: add support for the ea20 board
This board uses the OMAP-L138 SOM stacked on a
custom baseboard. It supports SPI Flash, Ethernet
with RMII.

Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-30 11:47:45 -05:00
Sughosh Ganu
48571ff005 Add board support for hawkboard
The patch adds basic board support for TI's OMAP-L138 based
Hawkboard. This board is pretty similar to the da850 EVM. Support for
nand and network access is added in this version.

The following bootup procedure is used.

At reset, the Rom Boot Loader(RBL), initialises the ddr and the nand
controllers and copies the second stage bootloader(nand_spl) to
RAM. The secondary bootloader then copies u-boot from a predefined
location in the nand flash to the RAM, and passes control to the
u-boot image.

Three config options are supported
* hawkboard_config - Used to create the u-boot.bin. Tftp the
 u-boot.bin image to the RAM from u-boot, and flash to the nand flash
 at address 0xe0000.

* hawkboard_nand_config - Used to generate the secondary
 bootloader(nand_spl) image. This creates an elf file u-boot-spl
 under nand_spl/. Create an AIS signed image using this file, and
 flash it to the nand flash at address 0x20000. The ais file should
 fit in one block.

* hawkboard_uart_config - This is same as the first image, but with
 the TEXT_BASE as expected by the RBL(0xc1080000). Create the AIS

Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-30 11:25:01 -05:00
Wolfgang Denk
93b1140090 ERIC: drop unsupported board configuration
The ERIC board appears to be unmaintained for more than 9 years. The
environment location has probably never been correct, and has been
definitely broken since for at least a year.  Drop it.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Swen Anderson <sand@peppercon.de>
Acked-by: Stefan Roese <sr@denx.de>
2010-11-26 22:08:17 +01:00
Eric Cooper
38041db740 Seagate FreeAgent DockStar support
start with sheevaplug configuration
add modifications by Alexander Holler <holler@ahsoftware.de>
    change RAM definitions to one bank (128 MB)
    change ident string and prompt
define MTD partitions and default environment variables
add support for LEDs

Signed-off-by: Eric Cooper <ecc@cmu.edu>
2010-11-26 21:12:52 +01:00
Dirk Eibach
a605ea7e83 ppc4xx: Add Io and IoCon 405EP board support
Board support for the Guntermann & Drunck CATCenter Io.
Board support for the Guntermann & Drunck IoCon.

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2010-10-25 17:07:46 +02:00
John Schmoller
bfe18815e8 XPedite5500 board support
Initial support for Extreme Engineering Solutions XPedite5500 -
a P2020-based PMC/XMC single board computer.

Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-22 03:04:41 -05:00
Peter Tyser
c00ac259f6 xes: Make X-ES board names more generic
Some U-Boot images for X-ES boards support multiple products in the same
family.  For example, the XPedite5370, XPedite5371, and XPedite5372 are
similar enough that one U-Boot image can work on all 3 cards.  To make it
clear that a U-Boot image can work on boards of the same family, rename
the boards with the least significant digit of 'x'.

While we're at it, change the board config file and make targets to be
lowercase.

Also change the default uImage and fdt filenames to "board.uImage" and
"board.dtb" to be more generic.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-22 02:17:23 -05:00
Wolfgang Denk
b18815752f Merge branch 'master' of git://git.denx.de/u-boot-arm 2010-10-20 00:10:07 +02:00
Kristoffer Ericson
80bf2bb501 Add support for HP Jornada flashrom boards
This patch adds support for the HP Jornada flashboards
that were made in 2008. Older flashroms should work if
memory registers are adjusted.

Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>

Adpted for TEXT_BASE -> CONFIG_SYS_TEXT_BASE rename.
Removed now redundant board/jornada/config.mk file.
Removed unused empty jornada_init() function to silence
"jornada.c:35: warning: 'jornada_init' defined but not used"

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-19 23:44:22 +02:00
Marek Vasut
c6d64c7cb1 PXA: Add missing MAINTAINERS entries
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2010-10-19 22:47:18 +02:00
Marek Vasut
10da95a13a PXA: Balloon3 board support
The following hardware is currently supported:
- UART
- USB Host
- FPGA

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2010-10-19 22:47:15 +02:00
Marek Vasut
f905432c04 PXA: Voipac270 improvements
128MB NOR module support.
Define __io to get harddrive working.
Fix saving of environment into OneNAND.
Boot from harddrive when possible.
Add missing MAINTAINERS entry.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2010-10-19 22:47:13 +02:00
Marek Vasut
6375dadab3 PXA: Add initial Palm LifeDrive support
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2010-10-19 22:47:09 +02:00
Marek Vasut
aaa2a2fc9b PXA: Palm Tungsten|C Support
This patch adds support for the Palm Tungsten|C PXA255 board. The support
includes:
- LCD
- MMC
- UART
- NOR

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
2010-10-19 22:47:02 +02:00
Andreas Bießmann
99fa97e955 at91rm9200ek: convert to at91
This patch removes some functionality from at91rm9200ek board but the
remaining functionality does now work with newer at91 code and
arm-relocation.

Currently missing features are:
 - dataflash booting (due to missing HW for testing)
 - MMC/SD-Card
 - first stage bootloader support is completely removed (not needed for
   NOR)

Cause this board was (some days ago) reference for all at91rm9200 based
boards this should be a good starting point to convert all remaining
at91rm9200 borads to at91 code. Aside from that this is a good base to
get some drivers between at91sam/at91rm/avr32 merged.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-10-19 15:11:46 +02:00
Wolfgang Denk
333d86d15a NC650/CP850: remove code for yet another corpse
The NC650 / CP850 boards have long been unmaintained and left broken.
As obviously nobody is interested in that code any more, we may as
well remove it.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-19 14:56:57 +02:00
Enric Balletbo i Serra
9c3c78870f MAINTAINERS: Fix alphabetical order in ARM subsection
I'm noticed that IGEP maintainer isn't in the correct place within
the ARM subsection: it's supposed to be in alphabetical order by
maintainer. This patch fix this.

Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
2010-10-18 22:25:03 +02:00
Enric Balletbo i Serra
1a832dc4f8 OMAP3: Add support for the OMAP3 IGEP module.
The IGEP module is a low-power, high performance production-ready
system-on-module (SOM) based on TI's OMAP3 family.The IGEP module
solution based upon TI OMAP3 provides a low-power/low-cost platform
for a variety of consumer/industrial/medical devices.

Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-10-17 20:14:42 +02:00
Enric Balletbo i Serra
8a3f6bb6fb OMAP3: Add support for the IGEP v2 board.
The IGEP v2 board is a low-cost, fan-less and industrial temperature
range single board computer that unleashes laptop-like performance and
expandability without the bulk, expense, or noise of typical desktop
machines. Its architecture shares much in common with other OMAP3 boards.

Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Steve Sakoman <steve.sakoman@linaro.org>
Tested-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-10-17 20:14:40 +02:00
Wolfgang Denk
e1b4c57096 Merge branch 'master' of git://git.denx.de/u-boot-arm 2010-10-13 20:59:47 +02:00
Matt Waddel
b80e41ac54 ARMV7: Versatile Express Coretile CortexA9x4 support
Adds support for the ARM quad-core Cortex-A9 processor

This system includes a motherboard(Versatile Express), daughterboard
(Coretile), and SOC(Cortex-A9 quad core).  The serial port, ethernet,
and flash systems work with these additions.  The naming convention
is:
   SOC -> CortexA9 quad core = ca9x4
   daughterboard -> Coretile = ct
   motherboard -> Versatile Express = vxp
This gives ca9x4_ct_vxp.c as the board support file.

Signed-off-by: Matt Waddel <matt.waddel@linaro.org>
2010-10-13 09:59:39 +02:00
Sergei Poselenov
9531a2388c A4M072: Added support for the board.
This patch provides support for the A4M072 board with the following features:
 UART
 NOR flash
 FEC Ethernet
 External SRAM
 I2C EEPROM
 CompactFlash cards on IDE/ATA port
 USB Host
 PCI initialization

The 7-segment LED indicator is not yet supported.

Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
2010-10-12 22:44:33 +02:00
Wolfgang Denk
e67f462864 Merge branch 'master' of git://git.denx.de/u-boot-imx 2010-10-11 10:19:04 +02:00
Stefano Babic
f8f8acd724 MX51: Support for TTECH vision2 board
The patch adds support for TTECH vision2 board.
The board has 512MB RAM, SDHC slot and 4MB SPI
device from StMicron.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-10-07 10:14:04 +02:00
Wolfgang Denk
dff07e18e5 CCM: remove code for yet another corpse
The CCM board has long reached EOL, and support for it is no longer
relevant in current versions of U-Boot.  Remove it.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-06 22:22:26 +02:00
Wolfgang Denk
544d97e9aa PCU_E: remove code for yet another corpse
The PCU_E board has long reached EOL, and support for it is no longer
relevant in current versions of U-Boot.  Remove it.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-06 22:22:24 +02:00
Wolfgang Denk
d628866474 Merge branch 'master' of git://git.denx.de/u-boot-blackfin 2010-10-05 14:42:32 +02:00
Tirumala Marri
d0e6665a24 APM821xx: Add bluestone board support
Add support code for bluestone board wth APM821XX processor based.
This patch includes early board init, misc init, configure EBC,
initializes UIC, MAKEALL, board.cfg and MAINTAINERS file.

Signed-off-by: Tirumala R Marri <tmarri@apm.com
Signed-off-by: Stefan Roese <sr@denx.de>
2010-10-04 11:17:38 +02:00
Wojtek Skulski
3bbed7f88a Blackfin: blackvme: new board port
The board includes:
 * ADSP-BF561 rev. 0.5
 * 32-bit SDRAM (2 * MT48LC16M16A2TG or MT48LC32M16A2TG)
 * Gigabit Ether AX88180 (ASIX) + 88E1111 rev. B2 (Marvell)
 * SPI  boot flash on PF2 (M25P64 8MB, or M25P128 16 MB)
 * FPGA boot flash on PF3 (M25P64 8MB, or M25P128 16 MB)
 * Spartan6-LX150 (memory-mapped; both PPIs also connected)
 * See http://www.skutek.com/

Signed-off-by: Wojtek Skulski <skulski@pas.rochester.edu>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02 16:00:40 -04:00
Peter Meerwald
063993299f Blackfin: bct-brettl2: new board port
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02 16:00:39 -04:00
Mike Frysinger
581e97df38 Blackfin: bf527-sdp: new board port
Support for the Blackfin System Development Platform (SDP) base module.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02 16:00:39 -04:00
Ilya Yanok
bc8f8c2614 mpc8308_p1m: support for MPC8308 P1M board
This patch provides support for MPC8308 P1M board with the following
set of features:
 Dual UART is supported
 NOR flash is supported
 Both TSEC Ethernet controllers are supported
 PCI Express initialization is supported
 Both I2C controllers are supported

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2010-09-23 21:14:17 +02:00
Stefano Babic
ec99d98341 MX51: Update responsible for mx51evk
Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-09-09 19:55:22 +02:00
Matthias Weisser
18a056a18f ARM: Add support for jadecpu board based on MB86R01 SoC
This patch adds support for the jadecpu board using the
MB86R01 'Jade' SoC from Fujitsu.

Signed-off-by: Matthias Weisser <weisserm@arcor.de>
2010-08-10 23:14:35 +02:00
Wolfgang Denk
0fe247b973 Drop support for GTH board
The board maintainer states:

    The GTH board is obsolete and has not been manufactured for
    several years.
    To my knowledge, no recent U-Boot build has been tested on that
    card.

So drop support for this board.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Thomas Lange <thomas@corelatus.se>
Acked-by: Thomas Lange<thomas@corelatus.se>
2010-07-17 20:47:08 +02:00
Wolfgang Denk
b6c208ab1e Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2010-07-16 23:15:01 +02:00
Timur Tabi
c59e1b4d07 powerpc: add support for the Freescale P1022DS reference board
Specifics:

1) 36-bit only
2) Booting from NOR flash only
3) Environment stored in NOR flash only
4) No SPI support
5) No DIU support

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-16 10:55:10 -05:00
Wolfgang Denk
93502a5e0a Merge branch 'master' of ../master 2010-07-15 22:48:46 +02:00
Wolfgang Denk
d6f324d03d Merge branch 'next' of git://git.denx.de/u-boot-nios 2010-07-14 22:07:41 +02:00
Wolfgang Denk
e1e3cf7c79 Merge branch 'master' of git://git.denx.de/u-boot-mpc83xx 2010-07-14 22:05:31 +02:00
Michael Hennerich
37aac2d30c Blackfin: bf527-ad7160-eval: new board support
Support the new AD7160 eval board.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-07-13 17:50:52 -04:00
Thomas Chou
a3c09f66b2 nios2: remove EP1C20, EP1S10, EP1S40 boards
The example configuration files of nios2-generic board can generated
binary to run on the EP1C20, EP1S10, and EP1S40 boards. So the three
boards can be removed.

With nios2-generic approach, the fpga parameter header file can
be generated from hardware designs using tools. Porting u-boot for
nios2 boards is simplified. Vendors can supply their fpga parameter
file or patches to add a new nios2-generic board instance. There is
no need to include other boards support for nios2 in the u-boot
mainline.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
2010-07-12 11:40:12 -04:00
Heiko Schocher
4e43b2e861 83xx: add support for ve8313 board
This patch add support for the ve8313 board based on
Freescale MPC8313 CPU.

- serial console on UART 1
- 128 MB DDR RAM
- 32 MB NOR Flash
- 16 MB NAND Flash
- Ethernet MII Mode over on TSEC0
- micrel ksz804 phy
- Hardware WDT MAX824

changes since v1
- Environment size = sector size
- use red. environment
- add comments from Kim Phillips
  - add MAKEALL, MAINTAINERS entry
  - Codingstyle issues fixed
  - inserted original Copyrights
  - PCI subsys vendor ID changed from 0x1057 (Motorola)
    to 0x1957 (Freescale)

changes since v2
- add comments from Wolfgang Denk
  - fix Codingstyle and some comments
  - reworked WDT reset (just toggling the WD_TRIG pin)
  - Environment size now 16KiB
  - fixed RAMBOOT version
  - fixed CONFIG_SYS_LOAD_ADDR
  - renamed CONFIG_TSEC1_NAME to TSEC1

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2010-07-09 16:10:44 -05:00
Ilya Yanok
5fb17030d5 MPC8308RDB: minimal support for devboard from Freescale
This patch provides support for MPC8308RDB development board from
Freescale with a minimal set of features:
 Dual UART is supported
 NOR flash is supported
 Both TSEC Ethernet controllers are supported
 PCI Express initialization is supported

The following features are enabled in configuration but not fully tested:
 I2C (used to get the board revision)
 I2C-connected RTC
 VSC7385 switch

There is one (hopefully) minor issue: on soft reset the board sometimes
resets twice. I've not managed to find the fix for this problem yet.
As a workaround instruction cache can be disabled.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2010-07-09 16:10:36 -05:00
Steve Sakoman
c57cca255c ARMV7: Add support for TI OMAP4 Panda
OMAP4 Panda is a reference board based on OMAP4430, an ARMV7 Cortex A9 CPU

This patch adds basic support for booting the board. It includes i2c and mmc
support. It assumes U-boot is loaded to SDRAM with the help of another small
bootloader (x-load) running from SRAM. U-boot currently relies on x-load for
clock, mux, and SDRAM initialization

Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-07-05 20:00:22 -04:00
Steve Sakoman
3e76d62a66 ARMV7: Add support for TI OMAP4430 SDP
OMAP4430 SDP is a reference board based on OMAP4430, an ARMV7 Cortex A9 CPU

This patch adds basic support for booting the board. It includes i2c and mmc
support. It assumes U-boot is loaded to SDRAM with the help of another small
bootloader (x-load) running from SRAM. U-boot currently relies on x-load for
clock, mux, and SDRAM initialization

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-07-05 20:00:15 -04:00
Steve Sakoman
f56348af5d ARM: Rename arch/arm/cpu/arm_cortexa8 to armv7
The purpose of this patch is to prepare for adding the OMAP4 architecture, which is Cortex A9

Cortex A8 and A9 both belong to the armv7 architecture, hence the name change.

The two architectures are similar enough that substantial code can be shared.

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-07-05 19:59:55 -04:00
Stefan Roese
273ed0370d ppc4xx: Add T3COPR board support (PPC460GT based)
This patch adds support for the T3CORP board, based on the
AppliedMicro (APM) PPC460GT.

Signed-off-by: Stefan Roese <sr@denx.de>
2010-07-01 10:26:30 +02:00
Guennadi Liakhovetski
b8c4eea56b remove myself as a maintainer of several ARM boards
Since I haven't been actively maintaining these boards for a long while,
keeping myself as their maintainer makes no sense.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
2010-06-22 22:58:00 +02:00
Wolfgang Denk
cecda170e7 Merge branch 'master' of git://git.denx.de/u-boot-marvell 2010-06-17 22:22:06 +02:00
Wolfgang Denk
530135dcac Merge branch 'master' of git://git.denx.de/u-boot-ti
Conflicts:
	CONFLICT (rename/add): Rename
	board/davinci/da830evm/Makefile->board/ti/tnetv107xevm/Makefile
	in 89b765c7f6.
	board/ti/tnetv107xevm/Makefile added in HEAD
But files were identical, so no problem.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-06-17 21:59:57 +02:00
Wolfgang Denk
399b09331f Merge branch 'master' of git://git.denx.de/u-boot-arm 2010-06-17 21:06:16 +02:00
Albert Aribaud
ce9c227cc7 Add support for the LaCie ED Mini V2 board
This patch adds support for the LaCie ED Mini V2 product
which is based on the Marvell Orion5x SoC.

Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
2010-06-17 19:38:21 +05:30
Minkyu Kang
c474a8ebb8 s5pc1xx: Add support for Samsung Goni board
This patch adds support for the Samsung Goni board (S5PC110 SoC)

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2010-06-14 18:15:20 -05:00
Sudhakar Rajashekhara
89b765c7f6 TI: DaVinci: Add board specific code for da850 EVM
Provides initial support for TI OMAP-L138/DA850 SoC devices on
a Logic PD EVM board.

Provides:
Initial boot and configuration.
Support for i2c.
UART support (console).

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-06-10 12:04:42 -04:00
Vaibhav Hiremath
ed01e45cfa AM35x: Add support for AM3517EVM
This patch adds basic support for the AM3517EVM.
It includes:
	- Board files (.c and .h)
	- Default configuration file
	- Updates for Makefile

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-06-08 10:07:18 -05:00
Cyril Chemparathy
5cc48f7e55 TI: TNETV107X EVM initial support
TNETV107X is a Texas Instruments SoC based on an ARM1176 core, and with a
bunch on on-chip integrated peripherals.  This patch adds support for the
TNETV107X EVM board.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-06-08 10:07:17 -05:00
Vaibhav Hiremath
3d9f0ffdda AM35x: Add support for AM3517EVM
This patch adds basic support for the AM3517EVM.
It includes:
	- Board files (.c and .h)
	- Default configuration file
	- Updates for Makefile

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-06-07 15:20:43 -04:00
Cyril Chemparathy
04cbc19fed TI: TNETV107X EVM initial support
TNETV107X is a Texas Instruments SoC based on an ARM1176 core, and with a
bunch on on-chip integrated peripherals.  This patch adds support for the
TNETV107X EVM board.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-06-07 14:13:36 -04:00
Asen Dimov
b5d289fc29 add new board pm9g45
Add the new board PM9G45 from Ronetix GmbH.
* AT91SAM9G45 MCU at 400Mhz.
* 128MB DDR2 SDRAM
* 256MB NAND
* 10/100 MBits Ethernet DP83848
* Serial number chip DS2401

The board is made as SODIMM200 module.
For more info www.ronatix.at or info@ronetix.at.

Signed-off-by: Asen Dimov <dimov@ronetix.at>
2010-06-06 08:36:28 -05:00
Thomas Chou
1117cbf2ad nios: remove nios-32 arch
The nios-32 arch is obsolete and broken. So it is removed.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
2010-05-28 10:56:04 -04:00
Wolfgang Denk
900a1fe8c8 Merge branch 'master' of git://git.denx.de/u-boot-arm 2010-05-04 22:49:15 +02:00
Siddarth Gore
16b76705d3 Marvell GuruPlug Board Support
GuruPlug Standard: 1 Gb Ethernet, 2 USB 2.0
GuruPlug Plus: 2 Gb Ethernet, 2 USB 2.0, 1 eSATA, 1 uSD slot

References:
http://www.globalscaletechnologies.com/t-guruplugdetails.aspx
http://plugcomputer.org

This patch is for GuruPlug Plus, but it supports Standard version
as well.

Signed-off-by: Siddarth Gore <gores@marvell.com>
2010-04-30 05:23:24 -05:00
Heiko Schocher
bbe310922f arm, i.mx27: add support for magnesium board from projectiondesign
This patch adds support for the magnesium board from
projectiondesign. This board uses i.MX27 SoC and has
8MB NOR flash, 128MB NAND flash, FEC ethernet controller
integrated into i.MX27. As this port is based on
the imx27lite port, common config options are collected
in include/configs/imx27lite-common.h

Signed-off-by: Heiko Schocher <hs@denx.de>
2010-04-30 05:23:23 -05:00
Stefan Roese
029faf3e85 ppc4xx: Add support for ICON board (PPC440SPe)
This patch adds support for the Mosaix Technologies, Inc. ICON board,
based on the AppliedMicro (AMCC) PPC440SPe. It's equipped with an SODIMM
(512MB standard) and 64MByte of NOR FLASH.

Support for the onboard SM502 will be added later.

Signed-off-by: Stefan Roese <sr@denx.de>
2010-04-29 10:16:20 +02:00
Wolfgang Denk
8e98f5f70b Merge branch 'master' of git://git.denx.de/u-boot-mpc5xxx 2010-04-27 23:02:12 +02:00
Thomas Chou
8cbb0ddd7e nios2: add nios2-generic board
This is a generic approach to port u-boot for nios2 boards.
You may find the usage of this approach on the nioswiki,
http://nioswiki.com/DasUBoot

A fpga parameter file, which contains base address information
and drivers declaration, is generated from Altera's hardware system
description sopc file using tools.

The example fpga parameter file is compatible with EP1C20, EP1S10
and EP1S40 boards. So these boards can be removed after this commit.
Though epcs controller is removed to cut the dependency of altera_spi
driver.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
2010-04-24 18:21:23 -04:00
Anatolij Gustschin
a3921eefa1 mpc5121: add support for PDM360NG board
PDM360NG is a MPC5121E based board by ifm ecomatic gmbh.

Signed-off-by: Michael Weiss <michael.weiss@ifm.com>
Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2010-04-24 22:56:37 +02:00
Wolfgang Denk
fd4e49c189 Merge branch 'master' of git://git.denx.de/u-boot-blackfin 2010-04-10 23:59:39 +02:00
Andre Schwarz
1f2463d764 Add initial support for Matrix Vision mvSMR board based on MPC5200B.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
2010-04-10 00:06:05 +02:00
Brent Kandetzki
3f1a5c1655 Blackfin: IP04: new board port
A low cost 4 port IP-PBX board.

Signed-off-by: Brent Kandetzki <BrentK@teleco.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-04-07 01:11:17 -04:00
Minkyu Kang
2ca551dd7a MAINTAINERS: sort the list of ARM Maintainers by last name
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2010-04-03 15:24:25 -05:00
Vipin KUMAR
c937c42431 SPEAr : Adding maintainer name for spear SoCs
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
2010-04-03 15:24:25 -05:00
Wolfgang Wegner
9d79e5758c add ASTRO MCF5373L board
This patch adds support for ASTRO board(s) based on MCF5373L.

Signed-off-by: Wolfgang Wegner <w.wegner@astro-kom.de>
2010-03-24 11:08:28 -05:00
Detlev Zundel
fd428c05c8 mpc5xxx: Remove all references to MGT5100
We do not support a processor that never reached a real customer.

Signed-off-by: Detlev Zundel <dzu@denx.de>
2010-03-21 22:44:42 +01:00
Detlev Zundel
9c9cbe78dc mpc82xx: Remove SL8245 board and the now orpahned sk98lin network driver.
This code has compile problems and the company does not even exist any
more.  So we take the liberty to drop support for it.

Signed-off-by: Detlev Zundel <dzu@denx.de>
CC: Wolfgang Denk <wd@denx.de>
CC: Ben Warren <biggerbadderben@gmail.com>
2010-03-12 09:49:23 +01:00
Heiko Schocher
67fa8c25f5 arm: add support for the suen3 board from keymile
Add support for the ARM part of the mgcoge2, named suen3.
This board is based on the Marvell Kirkwood (88F6281) SoC.
As there come more board variants, common config options
are collected in include/configs/km_arm.h. Also, this board
use common code for all keymile boards, which is stored in
board/keymile/common/common.c

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Heiko Schocher <hs@denx.de>
2010-03-07 12:36:36 -06:00
John Rigby
6895d4510a Add support for KARO TX25 board
This is an i.MX25 base board with only NAND
so it uses nand_spl to boot.

Signed-off-by: John Rigby <jcrigby@gmail.com>

Tune configuration, add support for (redundant) environment in NAND.
Signed-off-by: Wolfgang Denk <wd@denx.de>

Acked-by: Wolfgang Denk <wd@denx.de>
CC: Fred Fan <fanyefeng@gmail.com>
CC: Tom <Tom.Rix@windriver.com>
2010-03-07 12:36:36 -06:00
Stefano Babic
c5fb70c911 Add initial support for Freescale mx51evk board
The patch adds initial support for the Freescale mx51evk board.
Network (FEC) and SD controller (fsl_esdhc) are supported.

Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Fred Fan <fanyefeng@gmail.com>
2010-03-07 12:36:36 -06:00
Jens Scharsig
77e7273c40 new board (eb_cpux9k2)
* new board (eb_cpux9k2)
 * support for EB+CPUx9K2 board by BuS Elektronik GmbH & Co. KG
 * select via make eb_cpux9k2_config
 * this also demonstrates, how to use boards with AT91RM9200 cpu
   in at91 arch tree

Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
2010-02-12 12:36:04 -06:00
Matthias Kaehlcke
cf3c142ee4 Add support for EDB93xx boards
Added support for the following EDB93xx boards:

EDB9301
EDB9302
EDB9302A
EDB9307
EDB9307A
EDB93012
EDB9315
EDB9315A

Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
2010-02-12 12:31:54 -06:00
Daniel Gorsulowski
44d8025622 at91: Add esd gmbh OTC570 board support
This patch adds support for esd gmbh OTC570 board.
The OTC570 is based on an Atmel AT91SAM9263 SoC.

Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
2010-02-12 12:31:53 -06:00
Wolfgang Denk
d0750bc9e5 EXBITGEN: drop support for unmaintained board
The EXBITGEN board has not been maintained for a long time; it has
build problems, but no hardware is available any more for testing.

Drop support for this board.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
2010-02-03 20:01:16 +01:00
Alessandro Rubini
b9e6957ca1 MAINTAINERS: fix nhk8815 board name
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
2010-01-19 00:32:53 +01:00
Harald Krapfenbauer
2aeda2d054 Blackfin: tcm-bf518: new board port
Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-01-17 09:17:27 -05:00
Michael Hennerich
10eafa10be Blackfin: add support for BF527-EZKIT v2.1
The new board revision has a different LCD.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-01-17 09:17:27 -05:00
Valentin Yakovenkov
446707c90f Blackfin: bf561-acvilon: new board port
Signed-off-by: Valentin Yakovenkov <yakovenkov@niistt.ru>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-01-17 09:17:26 -05:00
Reinhard Arlt
1dee9be683 mpc83xx: Add support for MPC8349 esd caddy2
The caddy2 is a variant of the already supported vme8349. So we just
add the differences to this board port. To better support those two
boards we switched from fixed SDRAM configuration to usage of
spd_sdram(). This is done by providing a board specific SPD EEPROM
routine with different values for both boards.

Signed-off-by: Reinhard Arlt <reinhard.arlt@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>

changed to use mkconfig -t option instead, plus misc codingstyle fixes.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2010-01-07 18:34:31 -06:00
Wolfgang Denk
2a49bf3149 Merge branch 'master' into next
Conflicts:
	board/esd/plu405/plu405.c
	drivers/rtc/ftrtc010.c

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-12-05 02:11:59 +01:00