There are two same gmac node, remove one.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Update the tx_delay and rx_delay to match the timing for
rk3399-firefly board to improve the stability of gmac data
transfer.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
OLimex A64-OLinuXino is an open-source hardware board
using the Allwinner A64 SOC.
OLimex A64-OLinuXino has
- A64 Quad-core Cortex-A53 64bit
- 1GB or 2GB RAM DDR3L @ 672Mhz
- microSD slot and 4/8/16GB eMMC
- Debug TTL UART
- HDMI
- LCD
- IR receiver
- 5V DC power supply
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
NanoPi A64 is a new board of high performance with low cost
designed by FriendlyElec., using the Allwinner A64 SOC.
Nanopi A64 features
- Allwinner A64, 64-bit Quad-core Cortex-A53@648MHz to 1.152GHz, DVFS
- 1GB DDR3 RAM
- MicroSD
- Gigabit Ethernet (RTL8211E)
- Wi-Fi 802.11b/g/n
- IR receiver
- Audio In/Out
- Video In/Out
- Serial Debug Port
- microUSB 5V 2A DC power-supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
mmc using 150000000 as max-frequency like what rk3288 sets.
This can speed up the mmc read/write, the actual mmc clock is:
Before this patch: 37.125M
After this patch: 49.5M
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
add node for sdmmc in dts and rk3229-evb.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Device drivers like debug serial, dmc should be enabled before
relocation, so add u-boot.dtsi files to contain devices that
should be marked as dm-pre-reloc.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To use it with the DM timer driver in SPL and TPL, timer0 needs to be
marked as pre-reloc.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The RK3368-uQ7 (codenamed 'Lion') is a micro-Qseven (40mm x 70mm,
MXM-230 edge connector compatible with the Qseven specification)
form-factor system-on-module based on the octo-core Rockchip RK3368.
It is designed, supported and manufactured by Theobroma Systems.
It provides the following features:
- 8x Cortex-A53 (in 2 clusters of 4 cores each)
- (on-module) up to 4GB of DDR3 memory
- (on-module) SPI-NOR flash
- (on-module) eMMC
- Gigabit Ethernet (with an on-module KSZ9031 PHY)
- USB
- HDMI
- MIPI-DSI/single-channel LVDS (muxed on the 'LVDS-A' pin-group)
- various 'slow' interfaces (e.g. UART, SPI, I2C, I2S, ...)
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For full SPL support, including DRAM initialisation, we need a few
nodes from the DTS: this commit adds the DMC (DRAM controller) node,
the service_msch (memory scheduler) node and marks GRF, PMUGRF and CRU
as 'u-boot,dm-pre-reloc'. In addition to this, we also include the
dt-binding for the DMC to allow DTS files including this DTSI to refer
to the symbolic constants for the DDR3 bin and for the
memory-schedule.
Note that the DMC contains both the memory regions for the
(Designware) protocol controller as well as the DDR PHY.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We will to drop device security temporarily (until the ATF initialises
it fully) from the TPL/SPL stage: this requires access to some
registers in the SGRF.
This adds the sgrf node to the rk3368.dtsi, so we can then bind a
syscon device onto it and access its memory ranges.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Synced ohci0 and ehci0 nodes from Linux for sun50i-a64.dtsi
Here is the Linux last merge tag details:
Merge: 0e91f43d e5770b7
Author: Stephen Rothwell <sfr@canb.auug.org.au>
Date: Fri Jun 9 14:59:55 2017 +1000
Merge remote-tracking branch 'staging/staging-next'
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The node name for the power seq pin is mmc2@0 like the mmc2_pins_a one.
This makes the original node (mmc2_pins_a) scrapped out of the dtb and
result in a unusable eMMC if U-Boot didn't configured the pins to the
correct functions.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add the dts files to support deivce tree, update the configuration
files to support the device tree and driver model. The peripheral
clock and pins configuration are handled by the clock and the pinctrl
drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the dts files to support deivce tree, update the configuration
files to support the device tree and driver model. The peripheral
clock and pins configuration are handled by the clock and the pinctrl
drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update the configuration files to support the device tree and driver
model. The peripheral clock and pins configuration are handled by
the clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To support driver model and device tree, use the SPI-flash-based
AT45xxx DataFlash driver, DataFlash is a kind of SPI flash.
Instead of ATMEL_DATAFLASH_SPI DataFlash older driver that will
be removed in the future.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To support driver model and device tree, use the SPI-flash-based
AT45xxx DataFlash driver, DataFlash is a kind of SPI flash.
Instead of ATMEL_DATAFLASH_SPI DataFlash older driver that will
be removed in the future.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To support driver model and device tree, use the SPI-flash-based
AT45xxx DataFlash driver, DataFlash is a kind of SPI flash.
Instead of ATMEL_DATAFLASH_SPI DataFlash older driver that will
be removed in the future.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the dts files to support deivce tree, update the configuration
files to support the device tree and driver model. The peripheral
clock and pins configuration are handled by the clock and the pinctrl
drivers respectively.
Enable the early debug UART to debug problems when an ICE or other
debug mechanism is not available.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Import the RCar Gen3 DTS and headers from upstream Linux kernel v4.12-rc6,
commit 6f7da290413ba713f0cdd9ff1a2a9bb129ef4f6c . This includes both M3
and H3 ULCB and Salvator-X boards.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Not using board revision is causing confusion about which board is
supported and tested. Mark dts files exactly with board revision which
was tested. When new board revision arives it can be symlink if SW view
is the same. Also add -revX suffix to compatible string because user space
tools are parsing this string and can change behavior depends of board
revision.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Z-Turn board is a low cost development board based on the
Xilinx Zynq SoC. While it's powerful and quite versatile, it
so far lacked upstream support.
This patch adds basic support for the Z-Turn. It does however
for now miss enablement for MIO51 reset which means that USB
and ethernet don't work. For that either FSBL or SPL need to
be adjusted. The SPL part will follow later.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This will simplify dt overlay structure for the whole PL.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
This is shown as active high in the schematics[1], so fix it.
[1] https://patchwork.ozlabs.org/patch/777890/
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This property should be in the /chosen node, not /aliases.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Tested-by: Stephen Warren <swarren@nvidia.com>
Add this dts to enable debug uart releated devices
before relocation.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
When creating a EFI/GUID partition map for the RK3399-Q7 through
U-Boot, the partition entries should be places at a 1MB offset from
the start of the device to give us space for the environment (at 16KB
on SD/MMC devices), the SPL stage (at 32KB on SD/MMC devices) and the
image payload (at 256KB on SD/MMC devices).
This change sets this up through the u-boot,efi-partition-entries-offset
/config property in the RK3399-Q7 DTSI.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
As our SPL stage can grow quite large (80KB+ are not unusual) on the
RK3399-Q7, the default setting for the environment location (in
include/configs/rockchip-common.h) can overlap our SPL.
This change finally makes use of the 'u-boot,mmc-env-offset' DTS
property to override the environment location and put it at 16KB into
the device, which is right before the SPL (located at 32KB).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add regulator-init-microvolt for driver to init the regulator,
and the min output value is not 800000mV for the PWM2 io domain has
changed to VCC3V0 instead of VCC1V8 in rockchip evb, we need to
correct it with the value measured when PWM2 output HIGH.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
According to my test, some of firefly-rk3399 hang after dram init
when using ddr3-1333 config, while using ddr3-1600 config works
for all the board I have test.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The Identification Page (32 byte) is an additional page which can be written
and (later) permanently locked in Read-only mode.
phyCORE-RK3288 SoMs are using this page to describe the module variant.
This page also contains a MAC.
Our boards can be equipped with a different amount of EEPROMs. To make
this more transparent let's add an alias for the eeprom which stores the
module variant.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
FMC driver is now able to discover the bank number by
parsing bank subnodes.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use the same clocks macro than the one used by kernel DT.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Vikas MANOCHA <vikas.manocha@st.com>
Import Amlogic Meson DTS files from Linux kernel version 4.12
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It has been a while since ARM Trusted Firmware supported UniPhier SoC
family. U-Boot SPL was intended as a temporary loader that runs in
secure world. It is a maintenance headache to support two different
boot mechanisms. Secure firmware is realm of ARM Trusted Firmware
and now U-Boot only serves as a non-secure boot loader for UniPhier
ARMv8 SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This device tree is taken from mainline Linux kernel commit
7b7db5ab. Added is also a -u-boot.dtsi file with these additions:
- aliases for I2C and SPI devices are added, because i2cmux and
SPI flash doesn't work otherwise
- spi_flash node has been added so that the new DM API works
- the ATSHA204A node is added in the i2c@5 node
- "u-boot,dm-pre-reloc"s are added in needed nodes for SPL
build to work correctly
Signed-off-by: Marek Behun <marek.behun@nic.cz>
create mode 100644 arch/arm/dts/armada-385-turris-omnia-u-boot.dtsi
create mode 100644 arch/arm/dts/armada-385-turris-omnia.dts
Signed-off-by: Stefan Roese <sr@denx.de>
Many tegra boards have the console UART node disabled. With livetree this
prevents serial from working since it does not 'force' the console to be
bound. Updates the affected boards to fix this error.
The boards were checked with:
for b in $(grep tegra boards.cfg |grep -v integrator | \
awk '{print $7}' | sort); do
echo $b;
fdtgrep -c nvidia,tegra20-uart b/$b/u-boot.dtb |grep okay;
done
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Add aliases for mmc controller to get a fixed order with
emmc at index 0 and sdmmc at index 1.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use fixed regulator for sdmmc-pwren for sdmmc power.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The phyCORE-RK3288 is a SoM (System on Module) containing a RK3288 SoC.
The module can be connected to different carrier boards.
It can be also equipped with different RAM, SPI flash and eMMC variants.
The Rapid Development Kit option is using the following setup:
- 1 GB DDR3 RAM (2 Banks)
- 1x 4 KB EEPROM
- DP83867 Gigabit Ethernet PHY
- 16 MB SPI Flash
- 4 GB eMMC Flash
Add basic support for the PCM-947 carrier board, a RK3288 based development
board made by PHYTEC. This board works in a combination with
the phyCORE-RK3288 System on Module.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add fixed regulator for the port of typec0 and typec1 to control vbus
instead of gpio.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable dwc2 controller and add fixed regulator for dwc2 controller to
control vbus.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The driver changes gpio to fixed regulator to control vbus, so add
fixed regulator node in DTS for xhci driver.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable sdmmc device and add the spl boot device sequence.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Since the 'clock-freq-min-max' is deprecated, we use max-frequency.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Since the 'clock-freq-min-max' is deprecated, we use max-frequency.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Since the 'clock-freq-min-max' is deprecated, we use max-frequency.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The dts files are from kernel and with modify to adapt U-Boot.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add dmc node to enable sdram driver.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add a dmc node for sdram driver.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
gpio2 is used to detect lcd based on which pin mux is done in SPL.
gpio7 is used to enable vtt regulator. Enable these two gpio nodes
in SPL.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This port adds support for:
1) Serial
2) eMMC
3) USB
It has been tested with ARM TRUSTED FIRMWARE running u-boot as the
BL33 executable [see board's README]
eMMC has been tested for reading and booting the loader and linux
kernels as well as saving the u-boot environment.
USB has been tested with ASIX networking adapter and SanDisk 7.4GB
drive.
PSCI has been tested via the reset call (PSCI executes from DDR)
The firwmare upgrade process has been tested via TFTP and USB FAT
filesystem containing the fastboot.bin image in one of the partitions.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Add basic DT support for K2G ICE evm. Only minimal peripherals are
supported to allow console output and MMC boot.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Disable netcp by default like all other peripherals in the dtsi file.
Enable the peripheral explicitly in the board specific dts file.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Upstream Linux has the unit address being added to the various 66AK2Gx
boards dts. Therefore, update the dts to mimic this change.
Also remove memory node from the base K2G dtsi file.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adding the unit address to the memory node was causing the below error:
Warning (reg_format): "reg" property in /memory has invalid length
(8 bytes) (#address-cells == 2, #size-cells == 2)
Further debugging showed that this was due to the memory node added by
default to skeleton.dtsi which was being included in keystone-k2g.dtsi.
Adding a missing node was all that was needed to remove this deprecated
dtsi file from the SoC dtsi. With skeleton.dtsi removed the dtc compiler
no longer complained about including the unit address for the memory node.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
With U-boot runtime board detect for DTB selection a "default" dtb needs
to be created. This will be used temporarily until the "proper" dtb is
selected.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Introduce K2G evm specific dtsi file for U-boot specific configurations.
This will help seperate U-boot only configurations thus making it easier to
keep device tree files synced between U-boot and Linux.
For now only add nodes to allow i2c drivers to be probed early during
the boot process.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
With Davinci I2C switching to device model, K2E requires U-boot specific
device tree entries. This is only required for I2C 1 which is needed
extremely early during the boot process.
Fixes: 1743d040b1 ("ARM: keystone: Enable DM_I2C by default")
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
since commit: f8b7fff1d5 "serial: atmel_usart: Add clk support"
taurus board comes not up anymore. Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
since commit: f8b7fff1d5 "serial: atmel_usart: Add clk support"
smartweb board comes not up anymore. Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
Add initial device tree support for LD20 Global board.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add initial device tree support for LD11 Global board.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now that we can specify DT nodes that can be used in spl, mark
all necessary nodes as u-boot,dm-spl.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now that we can specify DT nodes that can be used in spl, mark
all necessary nodes as u-boot,dm-spl.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The topic-miamilite SoM contains a Zynq xc7z010 SoC, 1GB DDR3L RAM,
64MB dual-parallel QSPI NOR flash and clock sources.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
NanoPi NEO2 is designed and developed by FriendlyElec
using the Allwinner 64-bit H5 SOC.
NanoPi Neo2 key features
- Allwinner H5, Quad-core 64-bit Cortex-A53
- 512MB DDR3 RAM
- microSD slot
- 10/100/1000M Ethernet
- Serial Debug Port
- 5V 2A DC MicroUSB power-supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Orangepi Win/WinPlus is an open-source single-board computer
using the Allwinner A64 SOC.
A64 Orangepi Win/WinPlus has
- A64 Quad-core Cortex-A53 64bit
- 1GB(Win)/2GB(Win Plus) DDR3 SDRAM
- Debug TTL UART
- Four USB 2.0
- HDMI
- LCD
- Audio and MIC
- Wifi + BT
- IR receiver
- 5V DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Orangepi Zero Plus 2 is an open-source single-board computer
using the Allwinner h5 SOC.
H5 Orangepi Zero Plus 2 has
- Quad-core Cortex-A53
- 512MB DDR3
- micrSD slot and 8GB eMMC
- Debug TTL UART
- HDMI
- Wifi + BT
- OTG+power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Whistler is an ancient Tegra 2 reference board. I may have been the only
person who ever used it with upstream software, and I've just recycled
the board hardware. Hence, it makes sense to remove support from software.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
With Davinci I2C switching to device model, K2HK requires U-boot specific
device tree entries. This is only required for I2C 1 which is needed
extremely early during the boot process.
Fixes: 1743d040b1 ("ARM: keystone: Enable DM_I2C by default")
Reported-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
stm32x7.c driver is dedicated for STM32F7.
In kernel, "st,stm32-usart" and "st,stm32-uart" compatible
strings are dedicated for STM32F4.
To keep U-boot and kernel aligned, replace the serial compatible
string from "st,stm32-usart", "st,stm32-uart" to
"st,stm32f7-usart", "st,stm32f7-uart" specific for STM32F7.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Christophe KERELLO <christophe.kerello@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Acked-by: Vikas MANOCHA <vikas.manocha@st.com>
At present the interrupt does not work and the SPI bus runs much less
quickly than it should. Add settings to fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
NanoPi M1 Plus is designed and developed by FriendlyElec
for professionals, enterprise users, makers and hobbyists
using the Allwinner H3 SOC.
NanoPi M1 Plus key features
- Allwinner H3, Quad-core Cortex-A7@1.2GHz
- 1GB DDR3 RAM
- 8GB eMMC
- microSD slot
- 10/100/1000M Ethernet
- Serial Debug Port
- 5V 2A DC power-supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
This adds the DDR3-1866 timing via its own DTS and wires it up. This
(currently) is not the default timing for the RK3399-Q7 and should be
selected explicitly via the config (CONFIG_DEFAULT_DEVICE_TREE).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
This adds the DDR3-1333 timing via its own DTS and wires it up. This
is not the default timing for the RK3399-Q7 and should be selected
explicitly via the config (CONFIG_DEFAULT_DEVICE_TREE).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
To better support different RAM timings (DDR3-1333 and DDR3-1866 are
assembly options for the RK3399-Q7), this refactors the DTS support
and renames the default DTS variant from rk3399-puma to
rk3399-puma-ddr1600:
- changes the rk3399-puma DTS into a board-specific DTSI by removing
the inclusion of the DRAM timings
- adds a new rk3399-puma-ddr1600.dts, which includes the (new) common
board DTSI and the DDR3-1600 timing DTSI
- wires this up from arch/arm/dts/Makefile and configs/puma-rk3399_defconfig
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
The Linux DTS for the RK3399-Q7 has moved with the times... resync
against it to ensure a consistent configuration.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit enables HDMI output in the DTS by adding the necessary
nodes to vopl/vopb and by adding the HDMI node.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add basic support for rv1108 evb, whith this patch we
can boot into u-boot console.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
defines the spl-payload to 256k (0x40000)
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On the RK3399-Q7, the on-module USB3 hub is held in reset at boot-up
to save power and needs to be woken up using GPIO4A3.
Note that this is not a negated reset-signal (due to a level shifter
being needed for this signal anyway), but a negated enable-signal:
to enable, we need to output LOW (i.e. 0)... so we mark this as an
ACTIVE_LOW signal.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With the validation done for DDR3-1866 (i.e. 933 MHz bus clock), we
can now add the timings (rk3399-sdram-ddr3-1866.dtsi) for boards built
with the DDR3-1866 option.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
PX5 EVB is designed by Rockchip for automotive field
with integrated CVBS (TP2825) / MIPI DSI / CSI / LVDS
HDMI video input/output interface, audio codec ES8396,
WIFI / BT (on RTL8723BS), Gsensor BMA250E and light&proximity
sensor STK3410.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The GeekBox is a TV box from GeekBuying, based on an MXM3 module.
The module can be used with base boards such as the GeekBox Landingship.
This adds basic support to chain-load U-Boot from Rockchip's miniloader.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sheep board is designed by Rockchip as a EVB for rk3368.
Currently it is able to boot a linux kernel and system
to console with the miniloader run as fist level loader.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
The RK3368 is an octa-core Cortex-A53 SoC from Rockchip.
This adds basic support to chain-load U-Boot from Rockchip's
miniloader.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the LDO's nodes that taken from Linux Kernel.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Change the nodes relevant to mmc/sd for using DM.
compatible are also changed to each SoCs.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Orangepi Prime is an open-source single-board computer
using the Allwinner h5 SOC.
H5 Orangepi Prime has
- Quad-core Cortex-A53
- 2GB DDR3
- Debug TTL UART
- 1000M/100M Ethernet RJ45
- Three USB 2.0
- HDMI
- Audio and MIC
- Wifi + BT
- IR receiver
- HDMI
- Wifi + BT
Boot from MMC:
-------------
U-Boot SPL 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE: BL3-1: Running on H5 (1718) in SRAM A2 (@0x44000)
NOTICE: Configuring SPC Controller
NOTICE: BL3-1: v1.0(debug):aa75c8d
NOTICE: BL3-1: Built : 18:28:27, May 24 2017
INFO: BL3-1: Initializing runtime services
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9
U-Boot 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14 +0000) Allwinner Technology
CPU: Allwinner H5 (SUN50I)
Model: OrangePi Prime
DRAM: 2 GiB
MMC: SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: phy interface7
eth0: ethernet@1c30000
starting USB...
USB0: USB EHCI 1.00
USB1: USB OHCI 1.0
scanning bus 0 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner H5 SoC is pin-compatible to the H3 SoC,
but uses Cortex-A53 cores instead.
So move the shared cpu based and peripherals nodes into
sun50i-h5.dtsi so, that it can shared among the sun50i-h5
board dts files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
BPI-M64 is a 64-bit quad-core mini single board computer
using the Allwinner A64 SOC.
BPI-M64 features
- 1.2 Ghz Quad-Core ARM Cortex A53
- 2GB DDR3 SDRAM with 733MHz
- MicroSD/eMMC(8GB)
- 10/100/1000Mbps ethernet (Realtek RTL8211E/D)
- Wifi + BT
- IR receiver
- Audio In/Out
- Video In/Out
- 5V 2A DC power-supply
For dts file,
Sync with Linux commit 4879b7ae("Merge tag 'dmaengine-4.12-rc1'").
Boot from MMC:
-------------
U-Boot SPL 2017.05-00667-g85dd258-dirty (May 29 2017 - 13:07:31)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE: BL3-1: Running on A64/H64 (1689) in SRAM A2 (@0x44000)
NOTICE: Configuring SPC Controller
NOTICE: BL3-1: v1.0(debug):aa75c8d
NOTICE: BL3-1: Built : 18:28:27, May 24 2017
NOTICE: Configuring AXP PMIC
NOTICE: PMIC: setup successful
INFO: BL3-1: Initializing runtime services
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9
U-Boot 2017.05-00667-g85dd258-dirty (May 29 2017 - 13:07:31 +0000) Allwinner Technology
CPU: Allwinner A64 (SUN50I)
Model: BananaPi-M64
DRAM: 2 GiB
MMC: SUNXI SD/MMC: 0, SUNXI SD/MMC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: No ethernet found.
starting USB...
No controllers found
Hit any key to stop autoboot: 0
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Linux device tree for the Allwinner A64 SoC has changed a lot since
the U-Boot version was merged.
Let's replace the current DT with a exact copy of the Linux one as of:
commit c6778ff813d2ca3e3c8733c87dc8b6831a64578b
Merge: 0ff4c01 3c0e3abd
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Tue May 9 10:07:33 2017 -0700
This is the DT used in Linux 4.12-rc1.
Since U-Boot has an Ethernet driver (while Linux does not yet), we
provide the required DT nodes for it in an ...-u-boot.dtsi file, to both
mark them as U-Boot specific and to allow easier upgrading once Linux gets
the driver and its own binding later.
Compared to the existing Ethernet DT nodes we just slightly tweak the clock
and reset nodes in there to match the new bindings used by Linux for those.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
This patch enables the mvpp2 port 0 usage on the Armada 7k DB by setting
the correct PHY type (KR / SFI) for the COMPHY driver and enabling the
ethernet0 device node in the dts.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Start to populate the device tree of the Armada 37xx with the pincontrol
configuration used on the board providing a dts.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Add the nodes for the two pin controller present in the Armada 37xx SoCs.
Initially the node was named gpio1 using the same name that for the
register range in the datasheet. However renaming it pinctr_nb (nb for
North Bridge) makes more sens.
Minor changes for U-Boot because of the slightly different dts version
done by Stefan Roese.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Update the NanoPi Neo device tree file to use the NanoPi dtsi.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
NanoPi M1 is a board based on Allwinner H3 CPU.
This commit adds the support for this platform with:
- an include device tree which enables UART, LEDs, GPIO key switch,
1 USB host ports and the SD-card as a dtsi file.
- a device tree specific to this board that enables the
2 additional USB ports
- a defconfig file for minimal support
- a section in MAINTAINERS (add myself)
Synchronized with the kernel device tree, from commits:
sun8i-nanopi.dtsi: 85d2913614d9ab899d23b7ab7d22d23cf45bd1de
sun8i-h3-nanopi-m1.dts: 10efbf5f16336b7540ad6a16aa1cb0b26bab033b
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
LS2081ARDB board is similar to LS2080ARDB board with few differences
It hosts LS2081A SoC
Default boot source is QSPI-boot
It does not have IFC interface
RTC and QSPI flash device are different
It provides QIXIS access via I2C
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QSPI-boot is supported on LS2088ARDB RevF board with LS2088A SoC.
LS2088ARDB RevF Board has limitation that QIXIS can not be accessed.
CONFIG_FSL_QIXIS is not enabled.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
SDIO is not supported in u-boot, there is no point in enabling mmc3.
For this purpose, add u-boot specific dtsi that this will be included
automatically while building the dtb.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Sync with Linux commit 308ac756("Merge tag 'gpio-v4.11-3'").
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefan Agner <stefan.agner@toradex.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Add dts config for mipi display, include vop, mipi controller, panel, backlight
. And Enable rk808 for lcd_3v3 in another patch.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Set ethernet mac address in late init for Tinker Board,
prevents getting a random mac address each boot.
Read mac address from eeprom, first 6 bytes from m24c08@50.
Same as /etc/init.d/rockchip.sh on Tinker OS.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Firefly-rk3399 is a bord from T-Firefly, you can find detail about
it here:
http://en.t-firefly.com/en/firenow/Firefly_RK3399/
This patch add basic node for the board and make it able to bring
up.
Peripheral/interfaces on board:
- usb hub which connect to ehci controller;
- UART2 debug
- eMMC
- PCIe
- USB 3.0 HOST, type-C port
- sdio, sd-card
- HDMI
- Ethernet
- OPTICAL
- WiFi/BT
- MIPI CSI/DSI
- IR
- EDP/DP
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The kernel dts has update a lot since the first time we commit rk3399.dtsi,
sync with kernel for further development.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
The pwm3 on evb-rk3399 is used for pwm regulator, need to invert
the polarity to make it work correctly.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
With the validation done for DDR3-1600 (i.e. 800 MHz bus clock), we
add the timings (rk3399-sdram-ddr3-1600.dtsi) and change rk3399-puma.dts
to use these by default.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
Drop blank line at end of file:
Signed-off-by: Simon Glass <sjg@chromium.org>
The DDR3-1333 timings for the RK3399-Q7 (Puma) has some unintended
left-over comments in them. This change cleans the file up.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch also removes all the excessive code for NS16550 intiailization
as the device tree can do that now. This also adds DM_I2C and DM_MMC
since the overlying drivers have the built-in support already. The
corresponding include/config/omap3_logic.h also reduced in size
due to the new device tree support.
Signed-off-by: Adam Ford <aford173@gmail.com>
Changes in V2:
Retain Auto-detect ability between SOM-LV and Torpedo
Split this off from the device sub submissions
Previous commit has this combined with SOM-LV. This commit has only
the Torpedo Device Tree.
The device trees were sync'd with 4.9.y stable with two changes:
disable mmc2 and stdout-path = &uart1. Both of those two changes
will be submitted to the linux-omap list
Signed-off-by: Adam Ford <aford173@gmail.com>
Changes in V2:
Split device tree from other board
This adds the device tree. Previous commit added both boards at the
same time.
Signed-off-by: Adam Ford <aford173@gmail.com>
Changes in V2:
Split the SOM-LV from Torpedo
Some OMAP3 devices support an SMSC ethernet PHY connected to the GPMC bus.
This copies this device tree from Linux 4.9.y stable
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Many OMAP3 boards use a TWL4030 PMIC. This brings in the related
device tree information for common TWL4030 and TWL4030 with OMAP3.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Add device tree support to allow for CONFIG_OF_CONTROL in OMAP3630 boards.
DM3730 can use this same device tree.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Add device tree support to allow for CONFIG_OF_CONTROL in OMAP3 boards.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
This is needed to probe devices under that bus such as the SATA PHY.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree source files of at91sam9263ek boards are copied from
the Linux v4.10, do the changes as below.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC, pioD, pioE) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Add the "u-boot,dm-pre-reloc" property for the dbgu node are used
in board_init_f stage.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree source files of at91sam9rlek boards are copied from
the Linux v4.10, do the changes as below.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC, pioD) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Add the "u-boot,dm-pre-reloc" property for the dbgu node are used
in board_init_f stage.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree source files of at91sam9g20ek and at91sam9260ek
boards are copied from the Linux v4.10, do the changes below.
- Fix the build error for the usb0 node.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC ...) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Add the "u-boot,dm-pre-reloc" property for the dbgu node are used
in board_init_f stage.
- Add the clk pinctrl of the mmc0 node.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree source files of at91sam9m10g45ek boards are copied
from the Linux v4.10, do the changes as below.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC, pioD, pioE) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Add the "u-boot,dm-pre-reloc" property to determine which nodes
are used by the board_init_f stage.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree source files of at91sam9n12ek boards are copied from
the Linux v4.10, do the changes as below.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC, pioD) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Change the compatible of the spi flash to "spi-flash".
- Add the spi0 aliases.
- Fix the pinctrl-names of mmc0 node.
- Add the "u-boot,dm-pre-reloc" property to determine which nodes
are used by the board_init_f stage.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree source files of at91sam9x5ek board are copied from
the Linux v4.10, do the changes below.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC ...) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Add the "u-boot,dm-pre-reloc" property to determine which nodes
are used by the board_init_f stage.
- Change the compatible of the spi flash to "spi-flash".
- Add the spi0 aliases.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Move existing configuration from header file to defconfig or dts as
appropriate.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Align PHY selectors register with Armada-CP-110 functional SPEC
update all relevant device trees with this change.
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
UTMI_PHY_TO_USB_HOST was used in USB3 UTMI dts node only, but there will
be USB2 UTMI dts node for some SoCs that have got USB2 controller, so rename
TO_USB_HOST to TO_USB3_HOST to distinguish TO_USB2_HOST in later on patches.
Signed-off-by: zachary <zhangzg@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Use correct naming as done in the latest Marvell U-Boot version as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add NAND to CP master device tree. Add armada-7040-db-nand
device tree for the board configured with NAND boot device.
Add comment about boot device ID to armada-7040-db DTS.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Sync the default configuration of Armada-8040-DB with
Marvell u-boot-2015 standard configuration "A" for the same board.
The standard configuration "A" enables 2 PCIe slots on CP0
and 3 PCIe slots on CP1.
This is the main configuration used for u-boot and Linux tests.
This patch also re-arranges the DTS file entries by grouping
all nodes related to CP0 and CP1.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Enable I2C0 and I2C1 which is needed to enable usage of DM I2C.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add aliases for I2C nodes required for the DM framework to probe the
davinci-i2c driver.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add I2C nodes to the 66AK2Gx dtsi.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Remove unnecessary apb and ahb nodes and just override necessary
nodes/values.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for clocks needed by MACs to ast2500 clock driver.
The clocks are D2-PLL, which is used by both MACs and PCLK_MAC1 and
PCLK_MAC2 for MAC1 and MAC2 respectively.
The rate of D2-PLL is hardcoded to 250MHz -- the value used in Aspeed
SDK. It is not entirely clear from the datasheet how this clock is used
by MACs, so not clear if the rate would ever need to be different. So,
for now, hardcoding it is probably safer.
The rate of PCLK_MAC{1,2} is chosen based on MAC speed selected through
hardware strapping.
So, the network driver would only need to enable these clocks, no need
to configure the rate.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add Reset Driver configuration to ast2500 SoC Device Tree and bindings
for various reset signals
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch is required for correct SPL device tree creation by fdtgrep
as fdtgrep looks for u-boot,dm-pre-reloc property of the node to include
it in the spl device tree.
Not adding it in these subnodes ignores the pin muxing of peripherals
which is almost always in the subnodes.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This board support stm32f7 family device stm32f769-I with 2MB internal Flash &
512KB RAM.
STM32F769 lines offer the performance of the Cortex-M7 core (with double
precision floating point unit) running up to 216 MHz.
To compile for stm32f769 board, use same defconfig as stm32f746-disco,
the only difference is to pass "DEVICE_TREE=stm32f769-disco".
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
Actually the sdram memory on stm32f746 discovery board is micron part
MT48LC_4M32_B2B5_6A. This patch does the modification required in the
device tree node & driver for the same.
Also we are passing here all the timing parameters in terms of clock
cycles, so no need to convert time(ns or ms) to cycles.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
All discovery boards have one user button & one user LED. Here we are
just reading the button status & switching ON the user LED.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
Also created alias for gpios for stm32f7 discovery board. Based on these
aliases, it would be possible to get gpio devices by sequence.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
This patch also removes the sdram/fmc clock enable from board specific
code.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
Fixes the following problem:
zynq-uboot> run dfu_ram
Setting bus to 1
g_dnl_register: failed!, error: -19
The cause appears to be that the USB framework is looking for a usbotg aliases,
so add the alias to point to our USB device.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for the Terasic DE10-Nano board. The board
is based on the DE0-Nano-Soc board but adds a larger FPGA
and an HDMI output.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Reviewed-by: Dinh Nguyen <dinguyen@kernel.org>
Lichee Pi Zero is a development board with a V3s SoC, which features
64MiB DRAM co-packaged within the SoC, a TF slot, a SPI NOR slot (not
soldered in production batch), a 40-pin RGB LCD connector and some extra
pins available as 2.54mm pins or stamp holes.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As we have now V3s support in board code, the V3s DTSI file should also
be added.
Add also some CCU include headers to satisfy the DTSI file.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
- Use - instead of @ for OPP tables
- Add input-delay properties to Cadence eMMC nodes
- Restore full license text because code-diff is annoying
- Fix NAND compatible strings
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Bananapi M2 Ultra is the first publicly available development board
featuring the R40 SoC.
This patch add barebone dtsi/dts files for the R40 and Bananapi M2 Ultra,
as well as a defconfig for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
For using mipi display, we need to enable lcd3v3
which supplied by rk808,so enable rk808 first.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
To enable mipi display, we need to enable pmic
rk808 first for lcd3v3 power,which use i2c0 to
communicate with soc. So enable i2c0.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
The RK3399-Q7 (Puma) DTS should (of course) be dual-licensed.
This updates the licensing info in the rk3399-puma.dts.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Somehow 43b5c78d8d ("rockchip: cosmetic: Sort RK3288 boards") moved
the rock board in between some rk3288 board, probably as a result of
rebasing.
So move it back to its original position above all rk3288 boards.
Fixes: 43b5c78d8d ("rockchip: cosmetic: Sort RK3288 boards")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Disable the OC test on MCVEVK as the old PHY version does not provide
this information. This fixes the USB OTG operation.
Signed-off-by: Marek Vasut <marex@denx.de>
With the port C enabled, we can read the GPI input state of:
* the DIP switches (USER_DIPSW_HPS[3:0]/HPS_GPI[7:4])
* the push buttons (USER_PB_HPS[3:0]/HPS_GPI[11:8])
Signed-off-by: Georges Savoundararadj <savoundg@gmail.com>
Signed-off by: Sid-Ali Teir <git.syedelec@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Marek Vasut <marex@denx.de>
As a prerequisite for adding a Meson GX MMC driver update the
Meson GXBB / Odroid-C2 device tree in Uboot with the latest
version from Linux.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Add the device tree file for sama5d4ek board.
The dts file is copied from Linux-4.4, do the following changes.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compilation warning.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Add the device tree files for sama5d4 Xplained board.
The dts files are copied from Linux-4.4, do the following changes.
- add reg property for pinctrl node.
- move the gpio nodes(pioA, pioB, pioC ...) from the pinctrl child's
nodes to its slibling nodes.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Add the device tree file for sama5d3 Xplained board.
The dts files are copied from the Linux-4.9, do changes as below.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compile warning.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Add the device tree files for sama5d3xek board.
The dts files are copied from Linux-4.9, do the changes as below.
- add reg property for the pinctrl node.
- move the gpio nodes (pioA, pioB, pioC ...) as the pinctrl's
slibling nodes.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compile warning.
- add spi0 node aliases.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Logic PD has an i.MX6Q system on module (SOM) with a development kit. The
SOM has a built-in microSD socket, DDR and NAND flash. The development kit
has an SMSC Ethernet PHY, serial debug port and a variety of peripherals.
This have been verified to boot the i.MX6Q version over either SD
on the development kit or NAND built into the SOM. Items in the dtsi file
are specific to the SOM itself. Items in the dts file are in the baseboard.
Future versions of the SOM will come out supporting the same basebord and
potentially future base boards will come out supporting the same SOM.
Signed-off-by: Adam Ford <aford173@gmail.com>
The Sunchip CX-A99 is a board used in some media players. It features:
An Allwinner A80 ARM SoC (4 * Cortex-A7 + 4 * Cortex-A15 cores)
2 GiB or 4 GiB DDR3 DRAM
AXP808 PMIC
16 GB or 32 GB eMMC
SDIO Wifi/Bluetooth/FM module
SD card slot
1 USB 3.0 connector
2 USB 2.0 connectors
SATA connector
UART connector (internally) for serial console
Ethernet connector (10/100/1000 Mbit/s)
HDMI connector
Composite video and analog audio connector
S/PDIF connector
IR remote control receiver
This patch adds a defconfig for the board. The DRAM settings are as found
in the vendor sys_config.fex file.
It has a preliminary device tree for use until a device tree is accepted
upstream, after which it can be replaced by the upstream version.
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
[squash commits, and edited new meanful commit message]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
commit 56b0730157f70dc23d6caff9e7ceb8b377b96b9f upstream.
On the A80, mmc1 is available on pingroup G. Designs mostly use this
to connect to an SDIO WiFi chip.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Those DT will be part of 4.10, sync them so we can have our own config.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Add support for the NanoPi NEO Air H3 board from friendlyarm.com . This
board contains WiFi, Bluetooth, 8GB eMMC storage and 512 MB DDR3 ram.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[Rebase on master]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add the i2c-gpio nodes for fuelgauge and max77693.
There are i2c8 and i2c9.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The OrangePi PC 2 is a typical SBC with the 64-bit Allwinner H5 SoC.
Add a (64-bit only) defconfig defining the required options to build
the U-Boot proper.
Create a new .dts file for it by including the (32-bit) H3 SoC .dtsi
and changing the differing components accordingly.
This is a preliminary device tree mostly for U-Boot's own sake, it
is expected to be updated once the official DT gets accepted upstream.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[squash the commits, update the commit message]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
MiQi is rk3288 based development board with 1 or 2 GB SDRAM, 16 GB eMMC,
micro SD card interface, 4 USB 2.0 ports, HDMI, gigabit Ethernet and
expansion ports.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Eddie Cai <eddie.cai.linux@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Sort rk3288 boards in alphabetical order.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Eddie Cai <eddie.cai.linux@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The (shared) rk3399.dtsi had defined the 'rockchip,vbus-gpio'
properties for each USB 3.0 controller.
As the GPIO usage will vary (e.g. one of those GPIOs shuts down one of
the regulators on the RK3399-Q7) between boards, we move this from the
shared dtsi into the device tree file for the EVB board which these
GPIO definitions match.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
The RK3399-Q7 is a system-on-module featuring the Rockchip RK3399
in a Qseven-compatible form-factor.
These changes add a device-tree describing the board and its
interfaces for basic functionality (e.g. GbE, SPI, eMMC, SD-card).
This includes the following changes from the original development:
* dts: rk3399-puma: include DTS for RK3399-Q7 SoM in the Makefile
* dts: rk3399-puma: add gmac for the RK3399-Q7
This change enables the Gigabit Ethernet support on the RK3399-Q7.
* dts: rk3399-puma: use serial0 for stdout
* dts: rk3399-puma: prepare the sdmmc node for SPL booting
* dts: rk3399-puma: enable spi1 and spi5, add /spi1/spiflash
The RK3399-Q7 (Puma) unsually (this is a build-time option for
customised boards) has an on-module SPI-flash connected to SPI1.
As of today, this is a Winbond W25Q32DW (32MBit) device.
The SPI5 controller is routed to the Q7 edge connector and provides
general-purpose SPI connectivity for customer base-boards.
With some minor improvements on integration into our outbound tree
- explicitly modelled the SPI flash as 'spiflash' under spi0
[dts: rk3399-puma: explicitly model spi-flash under spi1]
- renamed the aliases to spi0 and spi1 to allow easier use of
commands and legacy (SPL) infrastructure... i.e. the controllers
will be 0 and 1 for 'sf probe', 'sspi', etc.
[dts: rk3399-puma: rename aliases to number spi as 0 and 1 for commands]
* dts: rk3399-puma: include SPI in the spl-boot-order property
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
For the initial validation of the RK3399-Q7 (Puma), the DDR3 has been
clocked at 666MHz (i.e. DDR3-1333) using the same (safe) settings as
used in Rockchip's MiniLoader.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
The Rock is a RK3188 based single board computer by Radxa.
Currently it still relies on the proprietary DDR init and
cannot use the generic SPL, but at least is able to boot
a linux kernel and system up to a regular login prompt.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fix sort order in defconfig, enable CONFIG_SPL_TINY_MEMSET:
Signed-off-by: Simon Glass <sjg@chromium.org>
firefly have a usb host. add dts node to provide power supply
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This change adds the gmac node (i.e. the GMAC Ethernet controller) as
defined in the Linux DTS.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
This includes Marvell mvpp2 patches with the ethernet support for the
ARMv8 Armada 7k/8k platforms. The ethernet patches are all acked by Joe
and he is okay with me pushing them via the Marvell tree.
Change the buck8's min-microvolt to 750000.
Whent thor protocol is used, board_usb_init() should be tried to set to
750000. But it was returned -EINVAL, because '750000' too lower than
2850000. (thor command doesn't work fine because of this problem.)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Trats has the i2c gpio for fuel-gaugge.
This patch s for preparing to use the fuel-gauge.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds board support for the Toradex Apalis TK1 a computer on
module which can be used on different carrier boards.
The module consists of a Tegra TK1 SoC, a PMIC solution, 2 GB of DDR3L
RAM, a bunch of level shifters, an eMMC, a TMP451 temperature sensor
chip, an I210 gigabit Ethernet controller and a SGTL5000 audio codec.
Furthermore, there is a Kinetis MK20DN512 companion micro controller for
analogue, CAN and resistive touch functionality.
For the sake of ease of use we do not distinguish between different
carrier boards for now as the base module features are deemed
sufficient enough for regular booting.
The following functionality is working so far:
- eMMC boot, environment storage and Toradex factory config block
- Gigabit Ethernet
- MMC/SD cards (both MMC1 as well as SD1 slot)
- USB client/host (dual role OTG port as client e.g. for DFU/UMS or host,
other two ports as host)
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The default configuration for the COMPHY-0 port should be 1G, as its
used as 1G SGMII connection. This change is necessary to get the
MAC2 port (SGMII) working on this DB.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit adds the description of the PPv2.2 hardware block for the
Marvell Armada 7K and Armada 8K processors, and their corresponding Armada
7040 and 8040 Development boards.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The gdsys ControlCenter Digital board is based on a Marvell Armada 38x
SOC.
It boots from SPI-Flash but can be configured to boot from SD-card for
factory programming and testing.
On board peripherals include:
- 2 x GbE
- Xilinx Kintex-7 FPGA connected via PCIe
- mSATA
- USB3 host
- Atmel TPM
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Initial DTS file for Marvell ESPRESSOBin comunity board
based on Armada-3720 SoC.
The Marvell ESPRESSOBin is a tiny board made by Globalscale
and available on KickStarter site. It has dual core Armv8
Marvell SoC (Armada-3720) with 512MB/1GB/2GB DDR3 RAM,
mini-PCIe 2.0 slot, single SATA-3 port, USB 2.0 and USB 3.0
interfaces, Gigabit Ethernet switch with 3 ports, micro-SD
socket and two 46-pin GPIO connectors.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add pin control nodes for North and South bridges to
Armada-37xx DT
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Added A8040 dts file for community board MACCHIATIBin.
The patch includes the following features:
AP - Serial console (connected to onboard FTDI usb to serial)
CP0 - PCIe x4, SATA, I2C and 10G KR
(connected to Marvell 3310 10G copper / SFP+ phy)
CP1 - Boot SPI, USB3 host, 2xSATA, 10G KR
(connected to Marvell 3310 10G copper / SFP+ phy),
SGMII connected to onboard 1512 1Gbps copper phy,
and additional SGMII connected to SFP
(default 1Gbps can be configured to 2.5Gbps).
Network interface naming -
egiga0 - CP0 KR
egiga1 - CP1 KR
egiga2 - CP1 RJ45 1Gbps connector (recommended for TFTP boot)
egiga3 - CP1 SFP default 1Gbps and can be modified to 2.5Gbps
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The gdsys ControlCenter Digital board is based on a Marvell Armada 38x
SOC.
It boots from SPI-Flash but can be configured to boot from SD-card for
factory programming and testing.
On board peripherals include:
- 2 x GbE
- Xilinx Kintex-7 FPGA connected via PCIe
- mSATA
- USB3 host
- Atmel TPM
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Initial DTS file for Marvell ESPRESSOBin comunity board
based on Armada-3720 SoC.
The Marvell ESPRESSOBin is a tiny board made by Globalscale
and available on KickStarter site. It has dual core Armv8
Marvell SoC (Armada-3720) with 512MB/1GB/2GB DDR3 RAM,
mini-PCIe 2.0 slot, single SATA-3 port, USB 2.0 and USB 3.0
interfaces, Gigabit Ethernet switch with 3 ports, micro-SD
socket and two 46-pin GPIO connectors.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add pin control nodes for North and South bridges to
Armada-37xx DT
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
