Qualcomm PMICs include a "pon" function which handles two buttons, the
power button and "resin" button (usually volume down). Introduce a new
driver following upstream Linux DT to enable these and map them to Enter
and Down respectively to enable use in boot menus.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
priv->pid is uint32_t, but dev_read_addr() returns a uint64_t on arm64,
with the upper bits being used for error codes. Do error checking before
downcasting to u32 to prevent errors being silently ignored.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
devm_clk_get() returns an ERR_PTR on failure, not null. Fix the check to
avoid the board crashing when the clock isn't available.
Additionally, add the missing error handling for this function.
Fixes: 324df15a29 ("serial: qcom: add support for GENI serial driver")
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
commit 1b15483deb ("misc: add Qualcomm GENI SE QUP device driver")
introduced support for platform-specific oversampling values, necessary
to configure the UART clocks on all platforms at runtime. However it
relies in probing a parent device. Despite the DM_FLAG_PRE_RELOC flag,
this is not done consistently during boot.
Instead, take another approach by relying on ofnode_ helpers to read the
serial engine base address and do the read directly. This fixes early
UART on boards with a non-default oversampling rate.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The pinctrl and GPIO drivers are currently heavily incompatible with
upstream. Most Qualcomm pinctrl blocks feature "tiles" of pins, each at
it's own address. Introduce support for these by allowing the soc driver
to specify per-pin register offsets similarly to the Linux driver.
Adjust the GPIO driver to handle these too, and finally enable support
for all pins with the same numbering as used in Linux.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Drop the duplicated pinctrl-snapdragon driver from mach-ipq40xx and add
it to drivers/pinctrl/qcom.
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Move the Qualcomm pinctrl drivers out of mach-snapdragon and over to the
rest of the pinctrl drivers, adjust the drivers so that support for each
platform can be enabled/disabled individually and introduce platform
specific configuration options.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The RCG divider field takes a value of (2*h - 1) where h is the divisor.
This allows fractional dividers to be supported by calculating them at
compile time using a macro.
However, the clk_rcg_set_rate_mnd() function was also performing the
calculation. Clean this all up and consistently use the F() macro to
calculate these at compile time and properly support fractional divisors.
Additionally, improve clk_bcr_update() to timeout with a warning rather
than hanging the board, and make the freq_tbl struct and helpers common
so that they can be reused by future platforms.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
This property is needed on some platforms to ensure that only the
relevant bits are set in the M/N/D registers.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Currently, it isn't possible to build clock drivers for more than one
platform due to how the msm_enable() and msm_set_rate() callbacks are
implemented.
Extend qcom_clk_data to include function pointers for these and convert
all platforms to use them.
Previously, clock drivers relied on include/configs/<board.h> to include the
board specific sysmap header, however as most of the header contents are clock
driver related, import the contents directly into each clock driver and
remove the header. The only exception here is the dragonboard820c board file
which includes some pinctrl macros, those are also inlined.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
[caleb: remove additional sysmap-sdm845.h mention]
Many gate clocks can be enabled with a single register write, add support
for defining these simple gate clocks and add the ones found on SDM845.
While we're here, inline clk_init_uart() into msm_set_rate().
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Qualcomm's clock controller blocks actually do much more than it
says on the tin.. They provide clocks, resets and power domains.
Currently, U-Boot requires one to spawn 2 separate devices for
controlling clocks and resets, both spanning the same register space.
Refactor the code to make it work with just a single DT node, making
it compatible with upstream Linux bindings and dropping the dedicated
reset driver in favour of including it in the clock driver.
Heavily inspired by Renesas code for a similar hw block.
[caleb: moved drivers to clk/qcom, added reset driver and adjusted bind
logic. Imported qcom,gcc-ipq4019.h from Linux]
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
This driver is just a stub, but it's necessary to support the upcoming
reset driver changes.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Clock drivers don't belong here, move them to the right place and
declutter mach-snapdragon a bit.
To de-couple these drivers from specific "target" platforms, add
additional config options to enable each clock driver gated behind a
common CLK_QCOM option and enable them by default for the respective
targets. This will make future work easier as we move towards a generic
Qualcomm target.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Set NAND chip ofnode and device so OF based partition parsing
can work.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://www.mail-archive.com/u-boot@lists.denx.de/msg499178.html
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
For DM case we can get the NAND chip's IO address from DT
so we don't need to rely on CFG_SYS_NAND_BASE.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://www.mail-archive.com/u-boot@lists.denx.de/msg499177.html
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
sys_proto.h no longer exists for K3 platform so drop it.
Include sizes.h to so SZ_16M is visible.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://www.mail-archive.com/u-boot@lists.denx.de/msg499176.html
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
The macro ELM_BASE is defined in mach/hardware.h and is
not visible at the omap_elm.h header file. Avoid using it
in omap_elm.h.
Reported-by: Hong Guan <hguan@ti.com>
Fixes: 7363cf0581 ("mtd: rawnand: omap_elm: u-boot driver model support")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/all/20231211114600.4414-3-rogerq@kernel.org
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
AM335x uses a special driver "am335x_spl_bch.c" as SPL
NAND loader. This driver expects 1 sector at a time ECC
and doesn't work well with multi-sector ECC that was implemented in
commit 04fcd25873 ("mtd: rawnand: omap_gpmc: Fix BCH6/16 HW based correction")
Additionally, the omap_elm driver does not support multi sector ECC and will
need more work and tests to get multi sector working correctly on all
platforms.
Switch back to 1 sector at a time read/ECC.
Fixes: 04fcd25873 ("mtd: rawnand: omap_gpmc: Fix BCH6/16 HW based correction")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Tested-by: Enrico Leto <enrico.leto@siemens.com>
Tested-by: Heiko Schocher <hs@denx.de>
Link: https://lore.kernel.org/all/20231211114600.4414-2-rogerq@kernel.org/
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
If the "mtd" parameter is NULL, the search will definitely yield a
negative result. In that case, it's better to exit immediately.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Link: https://lore.kernel.org/all/20231102113829.58852-1-dario.binacchi@amarulasolutions.com
Synchronize R-Car R8A77960 M3-W and R8A77961 M3-W+ clock tables with Linux 6.6.3,
commit bd3a9e5771a8b332f466d06f7c130a69cab0d526 .
Add ZG clock macro into rcar-gen3-cpg.h to cover the new clock type .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add properties to improve eye diagram which sometimes need adjust
some parameters of u2phy;
Add a property to tune disconnect threshold;
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
debug print delays reset of the driver. Finally I see
bunch of "rx error FFFF" errors in the screen. CI can
not handle many prints. While network works fine there
Reproduced with:
make CROSS_COMPILE=sh2-linux- r2dplus_defconfig all
qemu-system-sh4 -M r2d -nographic -serial null \
-serial mon:stdio -net user,tftp=`pwd` \
-net nic,model=rtl8139 -kernel ./u-boot.bin
Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
return value of smc911x_send is ignored, but on sucesseful
send we need return 0 and or error -ETIMEOUT, not opposite.
Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
u-boot-dfu-20240111
- Implement fastboot multi-response. This allows multi-line response and
most importantly, finally adds support for fastboot getvar all command.
- New 'fastboot oem console' command. Useful for debugging to send data
the u-boot shell via fastboot
- Console recording fixes
* make table_compute_checksum() arguments const
* remove duplicate function verify_checksum()
* enable setting processor family > 0xff
* set correct SMBIOS processor family value for RISC-V
* avoid importing ofnode.h in smbios.h
* provide a UEFI tool to dump SMBIOS table
-----BEGIN PGP SIGNATURE-----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=oHtG
-----END PGP SIGNATURE-----
Merge tag 'smbios-2024-04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request smbios-2024-04-rc1
* make table_compute_checksum() arguments const
* remove duplicate function verify_checksum()
* enable setting processor family > 0xff
* set correct SMBIOS processor family value for RISC-V
* avoid importing ofnode.h in smbios.h
* provide a UEFI tool to dump SMBIOS table
Use counterpart dev_read_* functions instead of fdt* ones. It fixes
checkpatch warnings like this:
WARNING: Use the livetree API (dev_read_...)
#54: FILE: drivers/pinctrl/exynos/pinctrl-exynos.c:137:
pinvals[idx] = fdtdec_get_int(fdt, node,
and also makes it possible to avoid using the global data pointer in the
driver.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Pull some variables declared in exynos_pinctrl_set_state() into its
loop, to reduce their scope. Style commit, no functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
All pin related dt properties (pin-function, pin-pud and pin-drv) are
handled in a very similar way. Get rid of that code duplication by
extracting the corresponding data knowledge into an actual data
structure (array), and then just iterating over it.
No functional change, it's a refactoring commit.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Get rid of hard-coded register offsets and widths. Instead provide a way
for pinctrl drivers to specify different pin bank register offsets and
widths. This in turn makes it possible to add support for new SoCs that
have registers with offset/width values different than generic ones
already available in pinctrl-exynos driver.
Offset constants (now unused in pinctrl-exynos.c) are moved to
pinctrl-exynos7420 driver, which is the single user of those constants.
The design of this patch follows Linux kernel pinctrl-exynos driver
design, in terms of added data structures and types. This patch doesn't
add support for any new SoCs and shouldn't introduce any functional
changes.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rework pin_to_bank_base() function to obtain bank data structure by bank
name instead of getting bank base address by pin name, and rename it to
get_bank() to reflect this change. This in turn leads to the extraction
of parse_pin(), so the caller has to use it before calling get_bank().
No functional change. This is a refactoring commit which prepares
pinctrl driver code for handling different sizes of register fields,
which will be added next.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Next commits are going to re-design the pin_to_bank_base() function and
its usage in a way that the pin parsing code will be called separately.
Extract it into a separate function first, as a refactoring commit.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Currently u-boot fastboot can only send one message back to host,
so if there is a need to print more than one line messages must be
kept sending until all the required data is obtained. This behavior
can be adjusted using multiresponce ability (getting multiple lines
of response) proposed in this patch.
Signed-off-by: Ion Agorria <ion@agorria.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20240105072212.6615-2-clamor95@gmail.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
The SMBIOS specification requires to set the processor family in the type 4
(Processor Information) table to specific values depending only on the
bitness of the system (0x200 for RV32 and 0x201 for RV64).
With this patch dmidecode shows
Handle 0x0004, DMI type 4, 48 bytes
Processor Information
Socket Designation: Not Specified
Type: Central Processor
Family: RV64
for qemu-riscv64_smode_defconfig.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The existence of devices should be checked in the bind method and not in
the probe method. Adjust the RISC-V Zkr RNG driver accordingly.
Use ENOENT (and not ENODEV) to signal that the device is not available.
Fixes: ceec977ba1 ("rng: Provide a RNG based on the RISC-V Zkr ISA extension")
Reported-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
In different parts of our code we assume that the first RNG device is the
one to be used. Therefore it is preferable to detect the availability of
the RNDR register already in the bind method.
For signaling the non-existence of a device the driver model requires using
ENOENT (and not ENODEV).
Fixes: 31565bb0aa ("driver: rng: Add DM_RNG interface for ARMv8.5 RNDR registers")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Invoke write_acpi_tables() via EVT_LAST_STAGE_INIT on QEMU except on X86.
X86 calls write_acpi_tables() in write_tables().
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move the code related to copying tables from QEMU to a separate code
module.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
We have two implementations of write_acpi_tables(). One for writing ACPI
tables based on ACPI_WRITER() entries another based on copying tables from
QEMU.
Create a symbol CONFIG_QFW_ACPI that signifies copying ACPI tables from
QEMU and use it consistently.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver is currently responsible for enabling the clock gating
feature of SiFive pre core's private L2 cache.
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add a basic implementation of the ARM SMMU. This driver is intended for
use on Qualcomm platforms where the SMMU has been configured by a previous
bootloader, cannot be turned off, and doesn't support BYPASS streams.
It keeps all existing stream mappings and only creates new ones for stream
ids that aren't already configured.
This driver is necessary to support peripherals that perform DMA which
weren't configured by the previous stage bootloader (for example USB).
It works by allocating a context bank using identity mapping (as U-Boot
doesn't use virtual addresses).
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Add an optional iommu callback to be invoked before a device probes.
This can be used to configure the IOMMU in preparation for the device
(e.g. by allocating a context bank)
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The dev_pci_iommu_enable() function is only available when CONFIG_PCI is
enabled, replace the runtime check with a preprocessor one to fix
compilation with pci disabled.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
These files include <common.h> twice. Start by removing the second
inclusion of the file.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to make it easier to move on to dropping common.h from code
directly, remove common.h inclusion from the rest of the header file
which had been including it.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
We need to include <config.h> directly when a file needs to have
something such as CFG_SYS_SDRAM_SIZE referenced as this file is not
automatically globally included and is most commonly indirectly included
via common.h. Remove most cases of arm including config.h directly, but
add it where needed. This includes a few board-specific fixes.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
In general terms, we -include include/linux/kconfig.h and so normal
U-Boot code does not need to also #include it. However, for code which
is shared with userspace we may need to add it so that either our full
config is available or so that macros such as CONFIG_IS_ENABLED() can be
evaluated. In this case make sure that we guard these includes with a
test for USE_HOSTCC so that it clear as to why we're doing this.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
-----BEGIN PGP SIGNATURE-----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=aBS6
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-next-20231220' of https://source.denx.de/u-boot/custodians/u-boot-amlogic into next
- Add support for new GXL MDIO mux, with driver and Linux DT sync from v6.4
Move all existing pinmux and funcmux code into a dedicated folder in
pinctrl to simplify further maintenance.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The existing pinctrl driver available for Tegra SOC is well
designed, but it lacks DM support. Let's add a DM compatible
overlay, which allows use of the device tree, along with preserving
backward compatibility with all existing setups and the ability
to use it in SPL board configuration stage.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The driver currently hard-codes the max freqency for the sdhci
controllers. If the controller is unable to operate at the max
frequency, the mmc card will not be available on the first scan.
Subsequent scans will eventually find a working combination.
Fix this by allowing the driver to check for the max-frequency
property and default to the original value if it doesn't exist.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
UCLASS_PMIC may have GPIO children without exposed fdt node,
in this case if requesting fails, check if uclass is PMIC.
Restrict build for supported devices only to save those precious
bytes on devices with no spare memory.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
MAXIM Semiconductor's PMIC, MAX77663 has 8 GPIO pins and 3 GPIO-like
pins. It also supports interrupts from these pins.
Add GPIO driver for these pins to control via GPIO APIs.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Julien Masson <jmasson@baylibre.com> says:
This patch series add the support for the MediaTek MT8365 EVK Board [1].
Most of the code have been copied/adapted from Linux tag v6.7-rc2.
For now we only enable/test these features:
Boot, UART, Watchdog and MMC.
[trini: This includes two clocks not listed in the Linux binding, which
needs resyncing later]
This patch adds clock driver support for MediaTek MT8365 SoC.
The changes are based on the Linux source code tag v6.7-rc2.
clk-mt8365.c has been written based on these kernel files:
- clk-mt8365.c (a96cbb146a9736f501fe66ebda6a9018735e5e8a)
- clk-mt8365-apmixedsys.c (65c9ad77cbc0eed78db94d80041aba675cfbdfa9)
And adapted following the clk attributes supported by U-Boot.
Signed-off-by: Julien Masson <jmasson@baylibre.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
The block count limit on MMC based devices should be set according to
CONFIG_SYS_MMC_MAX_BLK_COUNT instead of hardcoding value.
Signed-off-by: Julien Masson <jmasson@baylibre.com>
Change optee driver service enumeration to not enumerate (and
allocate a zero sized shared memory buffer) when OP-TEE
reports that there is no service to enumerate.
This change fixes an existing issue that occurs when the such zero
sized shared memory buffer allocated from malloc() has a physical
address of offset 0 of a physical 4kB page. In such case, OP-TEE
secure world refuses to register the zero-sized shared memory
area and makes U-Boot optee service enumeration to fail.
Fixes: 94ccfb78a4 ("drivers: tee: optee: discover OP-TEE services")
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Change optee probe function to only warn when service enumeration
sequence fails instead of reporting an optee driver probe failure.
Indeed U-Boot can still use OP-TEE even if some OP-TEE services are
not discovered.
Fixes: 94ccfb78a4 ("drivers: tee: optee: discover OP-TEE services")
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
DSP core is going into abnormal state when load callback is called
after starting of DSP core.
Reload of firmware needs core to be stopped first, followed by
load.
So avoid loading of firmware, when core is started.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Port the mdio-mux-meson-gxl.c Linux driver introduced in [1],
and adapt it to U-Boot.
This driver is needed to boot U-Boot with Linux DT since v6.4,
since it switched the MDIO mux from the mmio to a proper GXL driver.
[1] 9a24e1ff4326 ("net: mdio: add amlogic gxl mdio mux support")
Link: https://lore.kernel.org/r/20231213-u-boot-gxl-mdio-mux-v2-1-c56bb02a75ea@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add timer driver in Starfive SoC. It is an timer that outside
of CPU core and inside Starfive SoC.
Signed-off-by: Kuan Lim Lee <kuanlim.lee@starfivetech.com>
Signed-off-by: Wei Liang Lim <weiliang.lim@starfivetech.com>
Changes for v2:
- correct driver name, comment, variable
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The main thing in here is Igor's conversion of soc_clk_dump to a clk_ops
member. There's also a write-protect feature for nuvoton clocks.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
-----BEGIN PGP SIGNATURE-----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=z+Sl
-----END PGP SIGNATURE-----
Merge tag 'clk-2024.01-next' of https://source.denx.de/u-boot/custodians/u-boot-clk into next
clock patches for u-boot/next
The main thing in here is Igor's conversion of soc_clk_dump to a clk_ops
member. There's also a write-protect feature for nuvoton clocks.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Assign ccf_clk_ops to .ops of clk_ccf driver so that it can act as an
clk provider. Also add "#clock-cells=<1>" to its device tree node.
Add "i2c_root" to clk_test in the device tree and driver for testing.
Get "i2c_root" clock in CCF unit tests and add tests for it.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20231111-enable_count-v3-2-08a821892fa9@outlook.com
Add a flag to set ahb/apb/fiu/spi clock divider as read-only
The spi clock setting is related to booting flash, it is setup by early
bootloader.
It just protects the clock source and can't modify it in uboot.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20231114090004.3746024-1-JJLIU0@nuvoton.com
Switch to using new dump operation in clock provider drivers instead of
overriding soc_clk_dump.
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Igor Prusov <ivprusov@sberdevices.ru>
Link: https://lore.kernel.org/r/20231109105516.24892-8-ivprusov@sberdevices.ru
It's possible for composite clocks to have a divider that does not
implement set_rate() operation. For example, sandbox_clk_composite()
registers composite clock with a divider that only has get_rate().
Currently clk_composite_set_rate() only checks thate rate_ops are
present, so for sandbox it will cause NULL dereference during
clk_set_rate().
This patch adds rate_ops->set_rate check tp clk_composite_set_rate().
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20231205232334.2931-2-ivprusov@salutedevices.com
For some gate clocks and fixed clocks without a parent, calling
clk_register will print an useless error message indicating that parent
is missing. Fix that by gaurding log_xxx() with an if-statement.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Suggested-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20230807-clk-fix-v2-1-0b688e21fb4e@outlook.com
Add support to Orise Tech OTM8009A display on stm32f469-disco board.
It was necessary to retrieve the framebuffer address from the device tree
because the address returned by the video-uclass driver pointed to a memory
area that was not usable.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Set pllsaidivr only if the PLLSAIR output frequency is an exact multiple
of the pixel clock rate. Otherwise, we search through all combinations
of pllsaidivr * pllsair and use the one which gives the rate closest to
requested one.
Fixes: 5e993508cb ("clk: clk_stm32f: Add set_rate for LTDC clock")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The value to be written to the register must be appropriately shifted,
as is correctly done in other parts of the code.
Fixes: 5e993508cb ("clk: clk_stm32f: Add set_rate for LTDC clock")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add PLL settings for DDR 3600 MTps . This is very similar to 3200 MTps
PLL setting, except the divider is not 9 but 8 .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The new MX8M DDR tool 3.31 now generates a programming file which uses
data rate 3734 instead of 3733 or 3732 . Handle another rounding option .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
We are not iterating CQSPI_REG_RETRY, we are waiting 'timeout' ms, since
day 1.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
