Add SATA support on uDoo Board.
Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
In config_cmd_default.h, it will use CONFIG_SYS_NO_FLASH to decide
whether include CONFIG_CMD_FLASH and CONFIG_CMD_IMLS. So, move the
CONFIG_SYS_NO_FLASH to proper position, then we don't need to undef
these two commands.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
remove unneeded #undef for at91sam9x5ek board.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The last users of CONFIG_KGDB_SER_INDEX were removed more than 3 years
ago in commits 550650ddd0 and bf16500f79, either kgdb subsystem should
care about this parameter or it should be gone completely.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
This patch makes the following updates to the cm_t35 config file:
- Replace "ttyS" in default environment kernel bootargs with the new "ttyO"
notation.
- Remove "omapfb.debug=y" from default environment kernel bootargs.
- Define a minimal power-on delay for USB hub ports so that slow-to-power-on USB
sticks will have enough time to become responsive.
- Add support for bootz command
- ulpi_reset is not necessary and always fails with the following error message:
"ULPI: ulpi_reset: failed writing reset bit"
So, remove it.
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stefan Roese <sr@denx.de>
Pin 30 is connected to PHY's RESET# signal, so it must be
put to high. Otherwise PHY won't be found via MDIO interface.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
commit 16297cfb2a
Author: Mateusz Zalega <m.zalega@samsung.com>
Date: Fri Oct 4 19:22:26 2013 +0200
usb: new board-specific USB init interface
introduced a new parameter to the dfu command. Adapt the default environment
for the siemens boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Mateusz Zalega <m.zalega@samsung.com>
To make managing the environment easier, add DFUARGS to
CONFIG_EXTRA_ENV_SETTINGS. Then we set DFUARGS down in the DFU part of
the file, and include (or not) the NAND part, based on if NAND is set.
Signed-off-by: Tom Rini <trini@ti.com>
Add SPL U-Boot support to replace x-loader on the Compulab cm_t35
board. Currently only the 256MiB SDRAM board versions are supported.
Tested by booting via MMC and NAND.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
The memory size is autodetected and is passed to the Linux kernel
either via ATAGs or device-tree (dtb). So there is no need to
pass it via the bootargs.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>
Add SPL support for the Technexion TAO3530 SOM to replace
x-loader. Tested with the Thunder baseboard. Currently this is
only tested with the TAO3530 SOM revision (Ax/Bx).
Tested by booting via MMC and NAND.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>
Add support for TechNexion TAO3530 SoM
This patch has been posted quite a long time ago. I ported it to
the latest mainline U-Boot version. With some additional cleanup
and enhancements.
Signed-off-by: Tapani Utriainen <tapani@technexion.com>
CC: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>
With the current scenario SPL size is being overlapped with the public
stack and not allowing any OMAP4 device to boot. So the suggestion came
up was to move the TEXT_BASE down to non-HS limit. Fixing the same and
also moving the SRAM_SCRATCH_SPACE_ADDR up to the end of image
downloadable area.
Discussion on this can be seen here:
https://www.mail-archive.com/u-boot@lists.denx.de/msg127147.html
Tested on OMAP4460 PANDA.
Reported-by: Chao Xu <caesarxuchao@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
We want to test SPI flash code in the sandbox, so enable the new drivers and
the 'sf test' command.
This command is used to validate the sandbox SPI / SPI flash implementation,
so enable it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This allows us to put the SPI flash chip inside the SPI interface node,
with U-Boot finding the correct bus and chip select automatically.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for USB-A9263 board manufactured by Calao Systems
(http://www.calao-systems.com/).
Code is based on old U-Boot sources (2010.09) released by Calao.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
enable support for the siemens AT91SAM9G20 based board corvus.
Signed-off-by: Boris Schmidt <boris.schmidt@siemens.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
enable support for the siemens AT91SAM9G20 based boards taurus
and axm.
Signed-off-by: Roger Meier <r.meier@siemens.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Fixes this error message when USB is started.
"ULPI: ulpi_reset: failed writing reset bit"
It is pointless to manually reset the ULPI as the USB Host
Reset and PHY RESET line should take care of that.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Fixes this error message when USB is started.
"ULPI: ulpi_reset: failed writing reset bit"
It is pointless to manually reset the ULPI as the USB Host
Reset and PHY RESET line should take care of that.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Roger Quadros <rogerq@ti.com>
arndale board is booted from mmc
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Inderpal Singh <inderpal.singh@linaro.org>
This patch adapts the s3c24x0 driver to the new i2c framework.
Config file is modified for all the boards that use the driver.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
CC: Heiko Schocher <hs@denx.de>
CC: Inderpal Singh <inderpal.singh@linaro.org>
CC: David Müller <d.mueller@elsoft.ch>
CC: Chander Kashyap <k.chander@samsung.com>
CC: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
MPC8349 has been using mpc85xx DDR driver through a symbolic link to
mpc85xx_ddr_gen2.c. After consolidating the drivers to a single set
under driver/ddr/fsl/, the link is replaced by referring driver
directly. We now can simply enable the macro and use the driver.
Other mpc83xx SoCs still use their own driver.
Signed-off-by: York Sun <yorksun@freescale.com>
Usually CONFIG_FSL_DDR_INTERACTIVE feature is used for debug.
we would not enable this by default to save the limited space of u-boot.
This avoid following compiling error:
section .bootpg loaded at [00000000effff000,00000000effff577] overlap ssection
.data loaded at [00000000efff31b8,00000000f00010c7]
u-boot: section .bootpg lma 0xeffff000 adjusted to 0xf00010c8
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
In new board P1010RDB-PB, the interrupt vector table is at
the start of memory. So if the start_address needs to be set
a proper value.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Enable FDT support for all Siemens AM335x boards. To support
newer Linux kernels with DT booting.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Lukas Stockmann <lukas.stockmann@siemens.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Heiko Schocher<hs@denx.de>
Add support for the 16 bits pca9555 i2c to gpio extender featured
by the SB-T335 baseboard.
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Add support for status LED. Use the STATUS_LED APIs for indicating a
boot progress.
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
This patch updates Tizen partions layout.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
In this patch variable names are used instead of hardcoded names
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch implements a custom spi_copy funtion to copy u-boot from SF
to RAM. This is faster then iROM spi_copy funtion as this runs spi at
50Mhz and also in WORD mode of operation.
Changed a printf in pinmux.c to debug just to avoid the compilation
error in SPL.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The koelsch board has R8A7791, 2GB DDR3-SDRAM, USB,
Quad SPI, Ethernet, and more.
This patch supports the following functions:
- DDR3-SDRAM
- SCIF
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
Trats2 config is updated to support DFU mode.
Malloc pool must be increased for DFU buffer allocation.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds support for USB and enables 'ums' command on Trats2 board.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
In config_cmd_default.h, it will use CONFIG_SYS_NO_FLASH to decide
whether include CONFIG_CMD_FLASH and CONFIG_CMD_IMLS. So, if the
CONFIG_SYS_NO_FLASH defined later than include/config_cmd_default.h,
These two commands will be included always.
So move CONFIG_SYS_NO_FLASH definition to proper position.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Enable Atmel sama5d3xek boart spl boot support, which can load u-boot
from SD card with FAT file system.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The PLLADIV2 bit is not defined in at91sam9261 SoC, so remove it.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The SPI section is already defined in this file (lines 268-288) so we can
remove the duplicate definitions. While at it, also fix one tiny whitespace
typo.
Signed-off-by: Luka Perkov <luka@openwrt.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add Ethernet and networking support on uDoo board (FEC +phy Micrel KSZ9031).
Ethernet speed is currently limited to 10/100Mbps.
Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
mx6sabre board has a m25p32 SPI NOR connected to ECSPI1 port.
Add support for it.
This patch allows the SPI NOR flash to be succesfully detected:
=> sf probe
SF: Detected M25P32 with page size 256 Bytes, erase size 64 KiB, total 4 MiB
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
OCOTP driver is currently selected via CONFIG_MXC_OCOTP option.
Remove the old OCOTP related options, as they are not used anymore.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
CONFIG_SYS_NS16550_CLK specifies the rate of the clock 16x the baud
rate. The SMSC FDC37M81x datasheet states that a divider of 1 results in
a UART at 115200 baud, thus the x16 clock rate is 115200 * 16.
Previously the divider was left at 0 which led to a rate of 38400 baud
regardless of CONFIG_BAUDRATE or the baudrate environment variable.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Add the default RCW(SerDes 0x66_0x16) and PBI configure file for
T2080QDS board, so we can use PBL tool to generate the ramboot
image to support boot from NAND/SPI/SD.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
The T2080QDS is a high-performance computing evaluation, development and
test platform supporting the T2080 QorIQ Power Architecture processor.
T2080QDS feature overview
Processor:
- T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
Memory:
- Single memory controller capable of supporting DDR3 and DDR3-LV devices
- Two DDR3 DIMMs up to 4GB, Dual rank @ 2133MT/s and ECC support
Ethernet interfaces:
- Two 1Gbps RGMII on-board ports
- Four 10Gbps XFI on-board cages
- 1Gbps/2.5Gbps SGMII Riser card
- 10Gbps XAUI Riser card
Accelerator:
- DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
SerDes:
- 16 lanes up to 10.3125GHz
- Supports Aurora debug, PEX, SATA, SGMII, sRIO, HiGig, XFI and XAUI
IFC:
- 128MB NOR Flash, 512MB NAND Flash, PromJet debug port and FPGA
eSPI:
- Three SPI flash (16MB N25Q128A + 16MB EN25S64 + 512KB SST25WF040)
USB:
- Two USB2.0 ports with internal PHY (one Type-A + one micro Type-AB)
PCIE:
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
SATA:
- Two SATA 2.0 ports on-board
SRIO:
- Two Serial RapidIO 2.0 ports up to 5 GHz
eSDHC:
- Supports SD/SDHC/SDXC/eMMC Card
I2C:
- Four I2C controllers.
UART:
- Dual 4-pins UART serial ports
System Logic:
- QIXIS-II FPGA system controll
Debug Features:
- Support Legacy, COP/JTAG, Aurora, Event and EVT
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: removed Makefile blank line at EOF,
fix conflicts with moving DDR driver]
Acked-by: York Sun <yorksun@freescale.com>
Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs.
The similar DDR controllers will be used for ARM-based SoCs.
Signed-off-by: York Sun <yorksun@freescale.com>
The default partition table matches the .dts files for these boards in
Linux. This allows these partitions to be used by name with U-Boot's
"nand" command.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Commit 69434e4c deleted spieval board support
but it missed to clean up include/configs/spieval.h file.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Sandbox uses an emulated memory map which is quite small. We don't need the
CONFIG_PHYS_64BIT option since we can address memory with a 32-bit offset
into our ram_buf.
Adjust the phys_addr_t and phys_size_t types accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Hung-ying Tyan <tyanh@chromium.org>
This patch adds new CONFIG_NAND_OMAP_ECCSCHEME, replacing other distributed
CONFIG_xx used for selecting NAND ecc-schemes.
This patch aims at solving following issues.
1) Currently ecc-scheme is tied to SoC platform, which prevents user to select
other ecc-schemes also supported in hardware. like;
- most of OMAP3 SoC platforms use only 1-bit Hamming ecc-scheme, inspite
the fact that they can use higher ecc-schemes like 8-bit ecc-schemes with
software based error detection (OMAP_ECC_BCH4_CODE_HW_DETECTION_SW).
- most of AM33xx SoC plaforms use 8-bit BCH ecc-scheme for now, but hardware
supports BCH16 ecc-scheme also.
2) Different platforms use different CONFIG_xx to select ecc-schemes, which
adds confusion for user while migrating platforms.
- *CONFIG_NAND_OMAP_ELM* which enables ELM hardware engine, selects only
8-bit BCH ecc-scheme with h/w based error-correction (OMAP_ECC_BCH8_CODE_HW)
whereas ELM hardware engine supports other ecc-schemes also like; BCH4,
and BCH16 (in future).
- *CONFIG_NAND_OMAP_BCH8* selects 8-bit BCH ecc-scheme with s/w based error
correction (OMAP_ECC_BCH8_CODE_HW_DETECTION_SW).
- *CONFIG_SPL_NAND_SOFTECC* selects 1-bit Hamming ecc-scheme using s/w library
Thus adding new *CONFIG_NAND_OMAP_ECCSCHEME* de-couples ecc-scheme dependency
on SoC platform and NAND driver. And user can select ecc-scheme independently
foreach board.
However, selection some hardware based ecc-schemes (OMAP_ECC_BCHx_CODE_HW) still
depends on presence of ELM hardware engine on SoC. (Refer doc/README.nand)
Signed-off-by: Pekon Gupta <pekon@ti.com>
ELM hardware engine which is used for ECC error detection, is present on all
latest OMAP SoC (like OMAP4xxx, OMAP5xxx, DRA7xxx, AM33xx, AM43xx). Thus ELM
driver should be moved to common drivers/mtd/nand/ folder so that all SoC
having on-chip ELM hardware engine can re-use it.
This patch has following changes:
- mv arch/arm/include/asm/arch-am33xx/elm.h arch/arm/include/asm/omap_elm.h
- mv arch/arm/cpu/armv7/am33xx/elm.c drivers/mtd/nand/omap_elm.c
- update Makefiles
- update #include <asm/elm.h>
- add CONFIG_NAND_OMAP_ELM to compile driver/mtd/nand/omap_elm.c
and include in all board configs using AM33xx SoC platform.
Signed-off-by: Pekon Gupta <pekon@ti.com>
nand_ecclayout is present in mtd.h at Linux.
Move this structure to mtd.h to comply with Linux.
Also, increase the ecc placement locations to 640 to suport device having
writesize/oobsize of 8KB/640B. This means that the maximum oobsize has gone
up to 640 bytes and consequently the maximum ecc placement locations have
also gone up to 640.
Changes from Prabhabkar's version (squashed into one patch to preserve
bisectability):
- Added _LARGE to MTD_MAX_*_ENTRIES
This makes the names match current Linux source, and resolves
a conflict between
http://patchwork.ozlabs.org/patch/280488/
and
http://patchwork.ozlabs.org/patch/284513/
The former was posted first and is closer to matching Linux, but
unlike Linux it does not add _LARGE to the names. The second adds
_LARGE to one of the names, and depends on it in a subsequent patch
(http://patchwork.ozlabs.org/patch/284512/).
- Made max oobfree/eccpos configurable, and used this on tricorder,
alpr, ASH405, T4160QDS, and T4240QDS (these boards failed to build
for me without doing so, due to a size increase).
On tricorder SPL, this saves 2576 bytes (and makes the SPL build
again) versus the new default of 640 eccpos and 32 oobfree, and
saves 336 bytes versus the old default of 128 eccpos and 8 oobfree.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
CC: Vipin Kumar <vipin.kumar@st.com>
[scottwood@freescale.com: changes as described above]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Cc: Stefan Roese <sr@denx.de>
Cc: York Sun <yorksun@freescale.com>
Cc: Tom Rini <trini@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Since commit c2dd0d455 and 45bf05854 introduced
the new cache maintainance framework to ARM,
CONFIG_L2_OFF has not been used at all.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The physical base address of the NOR flash is 0x1e000000
on the Malta boards. The hardware also maps the first 4MiB
of the flash into the 0x1fc00000-0x1fffffff range.
Currently, U-Boot uses the mapped address to access the
flash, which does not work in recent qemu versions.
Since commit a427338b222b43197c2776cbc996936df0302f51
(mips_malta: correct reading MIPS revision at 0x1fc00010)
writing to the mapped address space causes a CPU exception.
Due to the exception, U-Boot hangs during boot when it tries
to detect the CFI flash chip.
Use the correct physical address for the MALTA_FLASH_BASE
constant to fix the problem. In order to avoid relocation
problems, also update the CONFIG_SYS_{TEXT,MONITOR}_BASE
constants.
The change makes it possible to start U-Boot on a Malta
board emulated with Qemu 1.6.1 and 1.7.0-rc0. It also
works on older versions (tested with 1.1.1, 1.2.2, 1.4.2,
1.5.3).
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
T1042RDB_PI is Freescale Reference Design Board supporting the T1042
QorIQ Power Architecture™ processor. T1042 is a reduced personality
of T1040 SoC without Integrated 8-port Gigabit. The board is designed
with low power features targeted for Printing Image Market.
T1042RDB_PI is similar to T1040RDB board with few differences like
it has video interface, supports T1042 personality
T1042RDB_PI board Overview
-----------------------
- Four e5500 cores, each with a private 256 KB L2 cache
- 256 KB shared L3 CoreNet platform cache (CPC)
- Interconnect CoreNet platform
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving
support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
for the following functions:
- Packet parsing, classification, and distribution
- Queue management for scheduling, packet sequencing, and congestion
management
- Cryptography Acceleration
- RegEx Pattern Matching Acceleration
- IEEE Std 1588 support
- Hardware buffer management for buffer allocation and deallocation
- Ethernet interfaces
- Two on-board RGMII 10/100/1G ethernet ports.
- SERDES Connections, 8 lanes supporting:
— PCI
— SATA 2.0
- DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and
Interleaving
-IFC/Local Bus
- NAND flash: 1GB 8-bit NAND flash
- NOR: 128MB 16-bit NOR Flash
- Ethernet
- Two on-board RGMII 10/100/1G ethernet ports.
- PHY #0 remains powered up during deep-sleep
- CPLD
- Clocks
- System and DDR clock (SYSCLK, “DDRCLK”)
- SERDES clocks
- Video
- DIU supports video at up to 1280x1024x32bpp
- HDMI connector
- Power Supplies
- USB
- Supports two USB 2.0 ports with integrated PHYs
- Two type A ports with 5V@1.5A per port.
- SDHC
- SDHC/SDXC connector
- SPI
- On-board 64MB SPI flash
- I2C
- Device connected: EEPROM, thermal monitor, VID controller, RTC
- Other IO
- Two Serial ports
- ProfiBus port
- Four I2C ports
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Use a default RCW of protocol 0x66.
A PBI configure file which uses CPC as 256KB SRAM. It can be used by
PBL tool on T1040 to build a pbl boot image.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
There is no real benefit in adding the board name into U-boot's prompt, so
remove the custom CONFIG_SYS_PROMPT definitions so that the standard "=> "
prompt is used across FSL boards.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
- add zync i2c driver to new multibus/multiadpater support
- adapted all config files, which uses this driver
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Michal Simek <michal.simek@xilinx.com>
- add omap24xx driver to new multibus/multiadpater support
- adapted all config files, which uses this driver
Tested on the am335x based siemens boards rut, dxr2 and pxm2
posted here:
http://patchwork.ozlabs.org/patch/263211/
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Tom Rini <trini@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Michael Jones <michael.jones@matrix-vision.de>
Cc: Raphael Assenat <raph@8d.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stefano Babic <sbabic@denx.de>
This updates to new I2C framwwork on sh_i2c.
And this also updates boards(kzm9g and ecovec) that using sh_i2c.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
- dxr2: define unused pins as input
- do not enable RTC32K OSC on dxr2 board
- update default environment
- add splashpos=m,m to default environment, so splash screen is always
centered.
- adapt environment for bootcount feature
- add altbootcmd to default environment
- rut: SPL add early reset pulse for eth-phy, maXTouch and display
- rut: display timing aenderungen
- siemens boards: adapt for background color = white
- add boutcount feature for the siemens boards
store the bootcount in the environment, as we have no softreset
save registers on this hardware. Use therefore the CONFIG_BOOTCOUNT_ENV
bootcount driver.
- change spi mode from 3 to 0 for the lcd init
- add gpio pin for lcd reset with state 0 and add mdelay
- siemens boards: use own USB id's
- add dfu serial and device number for siemens boards
Add for the siemens boards the possibility to define in dfu mode,
the iSerialNumber and the bcdDevice fields in the USB Device
descriptor.
- fix upgrade mechanism based on bootcount
Correct location of saveenv and remove not active variable.
Add CONFIG_BOOT_RETRY_TIME and CONFIG_RESET_TO_RETRY to
reboot board in case of empty kernel partition. Without
these defines an empty kernel partition leads to an
abort of boot process and one remains in u-boot prompt.
- general cleanup of dxr2, pxm2 and rut boards
all:
* Remove net boot from bootcmd
Ping can cause a crash on boards without ethernet phy.
net_nfs command is used only for development
* Add reset at the end of bootcmd
In order to have an immediate reset of the boot when bootcmd
fails, add reset at the end of bootcmd.
rut:
* add nand_img_size
dxr2:
* update nand_img_size
* ddr3 timings updated with iocontrol property that can be
modified via eeprom. New default parameters from software
leveling with draco ES2.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Pascal Bach <pascal.bach@siemens.com>
Signed-off-by: Roger Meier <r.meier@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matthias Michel <matthias.michel@siemens.com>
Cc: Tom Rini <trini@ti.com>
Use scf0403 driver to add scf0403x LCD support for cm-t35 and cm-t3730
boards.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
The MPC824x processors have long reached EOL, and the PN62 board has
not seen any board-specific updates for more than a decade. It is now
causing build issues. Instead of wasting time on things nobody is
interested in any more, we rather drop this board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
cc: Tom Rini <trini@ti.com>
Some am33xx boards may not use the RTC block for bootcount (as it may
not be wired up for the board) and use some other facility. So add
another symbol for the bootcount driver for the IP block.
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Switch to using the generic gpio_led driver instead of the private to
cm_t35 board led implementation.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
As
http://www.denx.de/wiki/view/U-Boot/DesignPrinciples#2_Keep_it_Fast
states:
"Initialize devices only when they are needed within U-Boot"
enable the RTC32K OSC only, if CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC is
enabled. Enable this in ti_am335x_common.h, so all boards in mainline
should work as before.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Conflicts:
arch/arm/cpu/arm926ejs/mxs/Makefile
board/compulab/cm_t35/Makefile
board/corscience/tricorder/Makefile
board/ppcag/bg0900/Makefile
drivers/bootcount/Makefile
include/configs/omap4_common.h
include/configs/pdnb3.h
Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:
board/compulab/common/Makefile
board/udoo/Makefile
include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.
include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.
Note: 'git show' will also list two files just because
they are new:
include/configs/am335x_igep0033.h
include/configs/omap3_igep00x0.h
The memsize environment variable must contain the
memory size in bytes on the Malta board. Otherwise
Linux will use wrong memory size which causes a kernel
panic.
Define CONFIG_MEMSIZE_IN_BYTES in malta.h to avoid
that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Allow the environment to be stored in the monitor flash of a Malta
board. The environment is stored in the final 128KB of the flash, which
both leaves the majority of the flash available for U-boot code and also
matches the location which YAMON uses.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
This is actually required in order for a Linux kernel to boot
successfully on a physical Malta board. Without enabling the RTC, a
Malta Linux kernel will get stuck in its estimate_frequencies function
on boot.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
These will now be detected at runtime, allowing a single U-boot
configuration to function correctly with different bitstreams. Without
this you may need to re-configure, re-build and re-flash U-boot to your
Malta if you flash a new bitstream with a different cache configuration
to your old bitstream.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
This model of the pcnet is used in current Malta boards, at least in the
Malta-R rev 3. Enable support for it.
The Malta also has the ethernet controller PROM containing its MAC
address, so enable support for that in order to read that MAC address.
DHCP is a very useful feature to have available for many networks,
enable support for it also.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
This patch adds support for running on Malta boards using coreFPGA6
core cards, including support for the msc01 system controller used
with them. The system controller is detected at runtime allowing one
U-boot binary to run on a Malta with either.
Due to the PCI I/O base differing between Maltas using gt64120 & msc01
system controllers, the UART setup is modified slightly. A second UART
is added so that there is one pointing at the correct address for each
system controller. The Malta board then defines its own
default_serial_console function to select the correct one at runtime.
The incorrect UART will simply not function.
Tested on:
- A coreFPGA6 Malta running interAptiv and proAptiv bitstreams, both
with and without an L2 cache.
- QEMU.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
This is in preparation for adapting this board to function correctly on
a physical MIPS Malta board. The board is moved into an "imgtec" vendor
directory at the same time in order to ready us for any other boards
supported by Imagination in the future.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
UMS init was implemented in trats board file but mostly it comprises
common code. Due to that it has been moved to common/ums.c to avoid
code duplication in the future.
Changes:
- move ums initialization code from trats to common/ums.c
- remove unused CONFIG_USB_GADGET_MASS_STORAGE from trats.h
Changes v2:
- move this patch at the top of code cleanups patches
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Commit 1b0757e deleted the EP88x entry from boards.cfg file.
But it missed to remove include/configs/EP88x.h and board/ep88x/.
This commit removes them and adds EP88x to README.scrapyard.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
The malloc space is to small to boot, the current uboot 2013.10-rcX,
This will fix the startup problems by increasing the mallog space to 4MiB.
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Since more functions are enabled, the eb_cpux9k2_ram target does not boot.
This patch changed the TEXT_BASE, that the code fits between TEXT_BASE and ram end.
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Get rid of too many ifdeffery in usb ohci driver
Add following two configuration for USB clock selecting
- CONFIG_USB_ATMEL_CLK_SEL_PLLB: using PLLB as usb ohci input clock
- CONFIG_USB_ATMEL_CLK_SEL_UPLL: using UPLL as usb ohci input clock
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add usb host support for at91sam9n12ek board.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The definitions for CONFIG_SYS_PROMPT are varied with little reason other
than to display the board name. Over half the definitions are "==> ", so
make this the default. The rest of the boards remain unchanged to avoid
breaking any external scripts expecting a certain prompt.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
This reverts commit 178b8e15ad.
Patch was merged too fast, without checking that another patch
is fixing the reported issue globally - reverted.
Signed-off--by: Stefano Babic <sbabic@denx.de>
rdaddr was missing which is a common location for loading ramdisks to.
loadaddr was higher than it needs to be, so use the same value other TI
platforms use.
Signed-off-by: Tom Rini <trini@ti.com>
Turn on GPIO commands for cm-t35 and cm-t3730.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Current default bootdelay of 10 seconds is too long.
Reduce default bootdelay to 3 seconds.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
UART booting is supported on this SoC, but via UART3 rather than UART1.
Because of this we must change the board to use UART3 for all console
access (only one UART is exposed on this board and a slight HW mod is
required to switch UARTs).
Signed-off-by: Minal Shah <minal.shah@ti.com>
[trini: Make apply to mainline, reword commit]
Signed-off-by: Tom Rini <trini@ti.com>
With changes to increase the size of the device tree (required to move
more data out of the kernel and into DT), loading the args at the old
address leads to us overwriting things later on. To correct this, load
the args file to where we load the device tree anyhow. This is also
safe for non-DT booting as in either case we use r2 to pass in the
location of things.
Signed-off-by: Tom Rini <trini@ti.com>
Increase the tested memory region for mtest and define
CONFIG_SYS_MEMTEST_SCRATCH for CONFIG_SYS_ALT_MEMTEST
Signed-off-by: Thomas Weber <thomas.weber@corscience.de>
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
Silent u-boot and no bootdelay
Signed-off-by: Thomas Weber <thomas.weber@corscience.de>
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
