Remove CONFIG_BOOT_RETRY_TIME as it doesn't do much good and enable
CONFIG_HUSH_PARSER in xtfpga_defconfig.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.
I did not attempt to add more default values in and for now will leave
that to maintainers.
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable validation of boot.scr script prior to its execution dependent
on "secureboot" flag in environment. Enable fall back option to
qspi boot in case of secure boot.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Currently in LS1088A, XIP mode in QSPI works up to 16 MB
addresses. This patch enables QSPI support in XIP mode for
addresses above 16 MB as well.
Signed-off-by: Rajat Srivastava <rajat.srivastava@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Migrate the base and sub-options to Kconfig. Note that we only enable
this in the base sandbox config now.
Cc: Alexey Brodkin <alexey.brodkin@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
---
Is this driver still used anywhere? It's fishy that it's only enabled
in sandbox anymore.
config_fallbacks.h had some logic to automatically select
LIB_RAND if RANDOM_UUID or CMD_UUID were set if LIB_HW_RAND wasn't
already selected. By migrating LIB_HW_RAND to Kconfig, we can
remove this check from config_fallbacks.h and put it into Kconfig
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
[trini: Turn into a choice, add NET_RANDOM_ETHADDR]
Signed-off-by: Tom Rini <trini@konsulko.com>
Distro default configuration contains also dhcp and pxe setting which
can't working without enabling CONFIG_NET.
EFI is not required that's why it is not enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The motivation for moving MX28 selection to Kconfig is to be able
to better handle NAND MXS selection through Kconfig.
This selection method also aligns with the way other i.MX SoCs are
selected in U-Boot.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
The motivation for moving MX23 selection to Kconfig is to be able
to better handle NAND MXS selection through Kconfig.
This selection method also aligns with the way other i.MX SoCs are
selected in U-Boot.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Since CONFIG_MXC_UART is already in Kconfig, move this from
the header to imx6q_logic_defconfig
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
cmd/Makefile has:
ifdef CONFIG_FPGA
obj-$(CONFIG_CMD_FPGA) += fpga.o
endif
which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently
does nothing. Let's remove that Makefile conditional and instead express
this equivalent dependency in Kconfig, so a lot of redundant
# CONFIG_CMD_FPGA is not set
can be removed from board defconfigs that don't actually have an FPGA.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
These are declared in Kconfig, but some #defines have crept in.
CONFIG_FPGA
CONFIG_FPGA_ALTERA
CONFIG_FPGA_CYCLON2
CONFIG_FPGA_SOCFPGA
CONFIG_FPGA_XILINX
CONFIG_FPGA_ZYNQMPPL
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
fastboot tool is a convenient way to flash the eMMC, so
add support for it.
Examples of usages:
On the mx6sabresd:
=> fastboot 0
On the Linux PC connected via USB:
$ sudo fastboot getvar bootloader-version -i 0x0525
bootloader-version: U-Boot 2018.01-00550-g7517cfe
finished. total time: 0.000s
$ sudo fastboot reboot -i 0x0525
(this causes the mx6sabresd to reboot)
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
The initial implementation of mx6memcal reset the CPU after
running the memory calibration procedure because the generic
board has no information about which boot devices are available.
Now that we have SDP support in SPL, use it to allow a full
U-Boot to be uploaded (i.e. to use "mtest").
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
This patch just changes the order of configuration items in
mx6memcal_defconfig to match the Kconfig layout, making it easier
to track changes made using menuconfig.
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Validate the time at startup:
- in case rtc error add to kernel command line RTC_ERROR
- clamp date to 1-Jan-2036
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Modify configuration to support FIT. Set variable `confidx' from VPD,
in order to load the correct device tree. Modify/simplify U-Boot
environment to support loading FIT image.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Modify b450v3, b650v3 and b850v3 defconfigs to enable the network devices
found in these products.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Enable nand on mmc defconfig, so-that preparing nand
for writing/updating bootimage, Linux becomes easy.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
i.CoreM6 1.5 is an another i.CoreM6 QDL cpu modules which can be connected
to EDIMM starter kit design with eMMC and MIPI-CSI interfaces suitable for
Android and video capture application.
notable features:
CPU NXP i.MX6 S/DL/D/Q, Up to 4 x Cortex-A9@800MHz
Memory Up to 2 GB DDR3-1066
Video Interfaces Up to 1 Parallel Up to 2 LVDS HDMI 1.4
port 8 bit CSI INPUT MIPI-CSI INPUT
1 x 10/100 Ethernet interface, 2 x USB, 1 x PCIe, 1 x I2S etc
This patch adds support for Quad/Dual and DualLite/Solo SOM's on
MIPI starter kit with boot from SD and eMMC.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
When functions return an error it propagates up the stack to the point
where it is reported. Often the error code provides enough information
about the root cause of the error that this is obvious what went wrong.
However in some cases the error may be hard to trace. For example if a
driver uses several devices to perform an operation, it may not be
obvious which one failed.
Add a log_ret() macro to help with this. This can be used to wrap any
error-return value. The logging system will then output a log record when
the original error is generated, making it easy to trace the call stack
of the error.
This macro can significantly impact code size, so its use is controlled
by a Kconfig option, which is enabled for sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
After moving some USB gadget configs (USB_FUNCTIONS_*) to Kconfig it
turned out that following *_defconfig entries for RockChip are not
needed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlpxesoACgkQykllyylKDCFwngCfZfk2S+c9uJCLh1drA7a+J4Ch
G+MAnA/iRu6/Ihd5UMe4tMK8BU51h0GQ
=Ylul
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2018.03' of git://git.denx.de/u-boot-microblaze
Xilinx changes for v2018.03
- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes
This converts the following to Kconfig:
CONFIG_SYS_OMAP24_I2C_SLAVE
CONFIG_SYS_OMAP24_I2C_SPEED
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Paul Kocialkowski <contact@paulk.fr>
This converts the following to Kconfig:
CONFIG_SYS_DV_CLKMODE
CONFIG_SYS_DA850_PLL0_POSTDIV
CONFIG_SYS_DA850_PLL0_PLLDIV1
CONFIG_SYS_DA850_PLL0_PLLDIV2
CONFIG_SYS_DA850_PLL0_PLLDIV3
CONFIG_SYS_DA850_PLL0_PLLDIV4
CONFIG_SYS_DA850_PLL0_PLLDIV5
CONFIG_SYS_DA850_PLL0_PLLDIV6
CONFIG_SYS_DA850_PLL0_PLLDIV7
CONFIG_SYS_DA850_PLL1_POSTDIV
CONFIG_SYS_DA850_PLL1_PLLDIV1
CONFIG_SYS_DA850_PLL1_PLLDIV2
CONFIG_SYS_DA850_PLL1_PLLDIV3
Signed-off-by: Adam Ford <aford173@gmail.com>
This patch moved ethernet PHY configs of ZynqMP boards
to respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch moved ethernet PHY configs of Microblaze board to
respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch moved ethernet PHY configs of Zynq boards
to respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds new target which is called as mini configuration
with only emmc functionality and other required basic features enabled.
This will be used to run in system with small footprint and needs
emmc support.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds new target which is called as mini configuration
with only nand functionality and other required basic features enabled.
This will be used to run in system with small footprint and needs
nand support.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
BOOTCOMMAND is composed with distro_bootcmd but this variable is not
present. Enabling distro defaults setting is fixing it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There are two reasons for doing this change.
There is still !DM driver for xilinx soft gpio IP and especially it is
saving some space for memory constrained boards like cse (almost ~400B).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason to enable BLK by default for all boards which is just
increasing memory footprint for memory contrained boards like cse.
zc770s are also saving some space.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Ethernet cable is not connected for xm011 that's why disable all
ethernet related configurations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
It is good to see this string to make sure that u-boot which runs on the
board is the same which should run there.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
These are defined, but not referenced at all.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
zc770-xm011 is x8 width configuration. This FMC card has also x16
variant which requires different ps7_init configuration. This patch adds
it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The bcm283x family of SoCs have a GPIO controller that also acts as
pinctrl controller.
This patch introduces a new pinctrl driver that can actually properly mux
devices into their device tree defined pin states and is now the primary
owner of the gpio device. The previous GPIO driver gets moved into a
subdevice of the pinctrl driver, bound to the same OF node.
That way whenever a device asks for pinctrl support, it gets it
automatically from the pinctrl driver and GPIO support is still available
in the normal command line phase.
Signed-off-by: Alexander Graf <agraf@suse.de>
Add gmac config support for rk3229 evb.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable GMAC configs for evb-rk3328
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
If the Ethernet address is not set, the network can't work,
enable the random address config for default use.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Since 7e0ed13 ("Convert ARCH_OMAP2PLUS boards' CONFIG_SYS_TEXT_BASE to
Kconfig"), a default SYS_TEXT_BASE was set for all ARCH_OMAP2PLUS devices.
CONFIG_ISW_ENTRY_ADDR is used to set SYS_TEXT_BASE in qspi boot.
Simplify this by directly assigning SYS_TEXT_BASE in the defconfig.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Convert the R8A7791 Porter board to DM and DT. This implies mostly
enabling the necessary configuration options and plucking out the
ad-hoc configuration from the board file. Moreover, the pre-reloc
malloc size was increased to allow the clock driver to start up
early without running out of malloc space and the early stack was
moved further up in the DRAM to avoid rewriting U-Boot itself.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since the DTs are now in place, enable OF control so that they get
bundled into the U-Boot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Now that we have everything in place in the code, let's allow to build
multiple environments backend through Kconfig.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
fdt overlay support is useful for all sunxi boards, enable per default
and remove it from sunxi defconfigs.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Currently, socfpga_common.h does not allow configurations without
network support. This is because CONFIG_CMD_PXE is defined in this
file and distro mode has DHCP hard-coded as available.
Fix this by moving CONFIG_CMD_PXE and CONFIG_MENU to the defconfigs
and by making DHCP optional in BOOT_TARGET_DEVICES(func).
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Convert these configuration options to Kconfig, update board defconfigs
and drop them from whitelist.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Pull out u-boot extras into dtsi files to make synchronization of DTS
from Linux kernel as easy as a simple copy. All the U-Boot extras are
now in *-u-boot.dts* files instead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This converts the following to Kconfig:
CONFIG_SOC_DA8XX
CONFIG_SOC_DA850
CONFIG_DA850_LOWLEVEL
CONFIG_MACH_DAVINCI_DA850_EVM
CONFIG_SYS_DA850_PLL_INIT
CONFIG_SYS_DA850_DDR_INIT
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: David Lechner <david@lechnology.com>
[trini: Rework CONFIG_SYS_DA850_PLL_INIT so it's selected on SOC_DA8XX]
Signed-off-by: Tom Rini <trini@konsulko.com>
Migrate the following symbols to Kconfig:
CONFIG_FS_EXT4
CONFIG_EXT4_WRITE
The definitions in config_fallbacks.h can now be expressed in Kconfig.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
This converts the following to Kconfig:
CONFIG_USB_MUSB_HCD
CONFIG_USB_MUSB_UDC
CONFIG_USB_DAVINCI
CONFIG_USB_OMAP3
CONFIG_USB_DA8XX
CONFIG_USB_AM35X
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts the following to Kconfig:
CONFIG_USB_MUSB_OMAP2PLUS
CONFIG_USB_MUSB_AM35X
CONFIG_USB_MUSB_DSPS
CONFIG_USB_MUSB_PIO_ONLY
Signed-off-by: Adam Ford <aford173@gmail.com>
The SPL doesn't have much room, so in order to support OF_CONTROL
in SPL, we need the extra functionality of SPL_OF_PLATDATA.
Adding these features allows us to remove a small part of code without
losing the serial port during SPL.
Signed-off-by: Adam Ford <aford173@gmail.com>
The following config symbols are only defined once and never referenced
anywhere else:
CONFIG_CYRUS
CONFIG_IDS8313
CONFIG_MPC8308_P1M
CONFIG_MPC8308RDB
CONFIG_MPC8349EMDS
CONFIG_MPC8349ITXGP
CONFIG_SBC8349
CONFIG_SBC8548
CONFIG_SBC8641D
CONFIG_TQM834X
CONFIG_VE8313
CONFIG_XPEDITE5140
CONFIG_XPEDITE5200
CONFIG_XPEDITE550X
Most of them are config symbols named after the respective boards which
seems to have been a standard practice at some point.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Acked-by: Mario Six <mario.six@gdsys.cc>
Move system flags from defconfig to mach-stm32/Kconfig
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Now this driver is used across stm32f4, stm32f7 and stm32h7
SoCs family, give it a generic name.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
This adds support for '-machine virt' on AArch64. This is rather simple:
we just add TARGET_QEMU_ARM_xxBIT to select a few different Kconfig
symbols, provide the ARMv8 memory map from the board file and add a new
defconfig based on the 32-bit defconfig.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Tom Rini <trini@konsulko.com>
CONFIG_OF_EMBED in particular is needed to allow the Raspberry Pi
firmware to pass the DTB to U-Boot and on to the kernel.
Signed-off-by: Drew Moseley <drew.moseley@northern.tech>
As HSDK is a development board it is better to hang on panic instead of
reset the board when panic occurs. That way we preserve a state of HW
for possibility to do post-mortem debug via JTAG.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We dont need to keep copies of the properties that we are going to
fixup since we will be using the dtb provided by the firmware.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
The firmware that runs before u-boot modifies u-boot's device tree
adding the local-mac-address and local-bd-address properties for the
compatibles "qcom,wcnss-bt" and "qcom,wcnss-wlan".
This commit reads that firmware, retrieves the properties and fixups
the device tree that is passed to the kernel before booting.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
This commit adds support for 96Boards Dragonboard820C.
The board is based on APQ8086 Qualcomm Soc, complying with the
96Boards specification.
Features
- 4x Kyro CPU (64 bit) up to 2.15GHz
- USB2.0
- USB3.0
- ISP
- Qualcomm Hexagon DSP
- SD 3.0 (UHS-I)
- UFS 2.0
- Qualcomm Adreno 530 GPU
- GPS
- BT 4.2
- Wi-Fi 2.4GHz, 5GHz (802.11ac)
- PCIe 2.0
- MIPI-CSI, MIPI-DSI
- I2S
U-Boot boots chained from LK (LK implements the fastboot protocol) in
64-bit mode.
For detailed build instructions see readme.txt in the board directory.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
LS1012A-2G5RDB belongs to LS1012A family with features 2 2.5G SGMII
PFE MAC, SATA, USB 2.0/3.0, WiFi DDR, eMMC, QuadSPI, UART.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This adds SH_ETHER to drivers/net/Kconfig and convert to Kconfig.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Enable CONFIG_B53_SWITCH, define the CPU/management port number (8) and
enable all 5 ports of the switch to be usable.
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Some distributions like Fedora expect U-Boot to select a proper
devicetree. Since there are several variants of the cm-fx6 module
featuring different SoC variants and the module can be paired with
several baseboards, it is not viable to hardcode a filename.
Instead, follow the lead of other i.MX6 based devices and try to
determine the devicetree to use with the help of the board name
and the SoC variant exported by the board code, before calling the
distro bootcommand.
For now, only for the Utilite Pro a proper devicetree filename is
known but further variants of the Utilite Computer or other devices
based on the cm-fx6 module may be added in the future.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
To support QSPI DM driver
- Add spi0 alias for qspi node. Which is used for bus number 0.
- Modify the n25q256a@0 compatible property to "spi-flash".
- Modify spi4 (gpio_spi) node to spi5
- Define DM SPI/QSPI related config to enable QSPI
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable I2C/MMC/GPIO/REGUALTOR/PMIC/USB DM drivers.
There are some dependency, such as when DM MMC enabled, USB compile error.
Also the i.MX I2C MMC DM driver does not support legacy GPIO interface.
So enable them all together.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Add nx25-ae250 default configuration for RISC-V
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Signed-off-by: Greentime Hu <green.hu@gmail.com>
The am335x_hs_evm runs into size constraint problems at times with
various toolchains as changes come in due to the config have a large
number of options in SPL (to showcase what is possible) while also
having rather constrained binary limits. Gain some of this room back by
lowering the loglevel, disabling HW partition support and switching over
to the tiny FIT image support.
Cc: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
---
I'd really appreciate a run-time test of this patch if at all possible
as I'm a little worried about TINY_FIT being incompatible with all of
the security options. Thanks!
The changes in the MMC stack have increased its footprint up to the point
were its breaks the generation of the SPL for this platform.
Fix this by reducing the loglevel.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Peter Howard <phoward@gme.net.au>
builds are broken because the size of the binary exceeds the limit.
Make some space by removing support for hardware partitioning as those
boards don't have any eMMC.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
a64-olinuxino has 8GiB eMMC, enable it.
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The CONFIG_SYS_DPAA_QBMAN define is used by DPAA1 freescale SOCs to
add device tree fixups that allow deep sleep in Linux. The define was
placed in header files included by a number of boards, but was not
explicitly documented in any of the Kconfigs. A description was added
to the drivers/networking menuconfig and default selection for
current SOCs that have this part
Signed-off-by: Ahmed Mansour <ahmed.mansour@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Configure AM57xx EVMs for the exact PHY part that is
present on the various boards. This makes U-Boot apply
configurations needed for this PHY like centering the
FLP timing.
For configurations to take effect, DM_ETH needs to be
enabled. Do that too.
Tested on BeagleBoard x15 and AM571x IDK.
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This board offers :
_ STM32F469NIH6 microcontroller featuring 2 Mbytes of Flash memory
and 324 Kbytes of RAM in BGA216 package
_ On-board ST-LINK/V2-1 SWD debugger, supporting USB reenumeration capability:
_ Mbed-enabled (mbed.org)
_ USB functions: USB virtual COM port, mass storage, debug port
_ 4 inches 800x480 pixel TFT color LCD with MIPI DSI interface and capacitive
touch screen
_ SAI Audio DAC, with a stereo headphone output jack
_ 3 MEMS microphones
_ MicroSD card connector
_ I2C extension connector
_ 4Mx32bit SDRAM
_ 128-Mbit Quad-SPI NOR Flash
_ Reset and wake-up buttons
_ 4 color user LEDs
_ USB OTG FS with Micro-AB connector
_ Three power supply options:
_ Expansion connectors and Arduino™ UNO V3 connectors
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Use available DM stm32f7_gpio.c and pinctrl_stm32.c drivers
instead of board GPIO initialization.
Remove stm32_gpio.c which is no more used and migrate
structs stm32_gpio_regs and stm32_gpio_priv into
arch-stm32f4/gpio.h to not break compilation.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Use available DM clk_stm32f.c driver instead of dedicated
mach-stm32/stm32f4/clock.c.
Migrate periph_clock defines from stm32_periph.h directly in
CLK driver. These periph_clock defines will be removed when STMMAC,
TIMER2 and SYSCFG drivers will support DM CLK.
Enable also CLK flag.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Remove serial_stm32.c driver and uart init from board file,
use available DM serial_stm32x7.c driver compatible for
STM32F4/F7 and H7 SoCs.
The serial_stm32x7.c driver will be renamed later with a more
generic name as it's shared with all STM32 Socs.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This allows to support rcc MFD driver.
By enabling all these flags, we need to increase malloc area to avoid
crash during early stage.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Use available DM stm32_sdram.c driver instead of board
SDRAM initialization.
For that, enable OF_CONTROL, OF_EMBED and STM32_SDRAM flags.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
this patch enable rockusb support on rk3288 based device.
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Libre Computer Board ALL-H3-CC from Libre Technology is a Raspberry
Pi B+ form factor single board computer based on the Allwinner H3 SoC.
The board has 1GB DDR3 SDRAM, provided by 4 2Gb chips. The mounting holes
and connectors are in the exact same position as on the Raspberry Pi B+.
Raspberry Pi B+ like peripherals supported on this board include:
- Power input through micro-USB connector (without USB OTG)
- Native 100 Mbps ethernet using the internal PHY, as opposed to
USB-based on the RPi
- 4x USB 2.0 host ports, directly connected to the SoC, as opposed to
being connected through a USB 2.0 hub on the RPi
- TV and audio output on a 3.5mm TRRS jack
- HDMI output
- Micro-SD card slot
- Standard RPi B+ GPIO header, with the standard peripherals routed to
the same pins.
* 5V, 3.3V power, and ground
* I2C0 on the H3 is routed to I2C1 pins on the RPi header
* I2C1 on the H3 is routed to I2C0 pins on the RPi header
* UART1 on the H3 is routed to UART0 pins on the RPi header
* SPI0 on the H3 is routed to SPI0 pins on the RPi header,
with GPIO pin PA17 replacing the missing Chip Select 1
* I2S1 on the H3 is routed to PCM pins on the RPi header
- Additional peripherals from the H3 are available on different pins.
These include I2S0, JTAG, PWM1, SPDIF, SPI1, and UART3
In addition, there are a number of new features:
- Console UART header
- Consumer IR receiver
- Camera interface (not compatible with RPi)
- Onboard microphone
- eMMC expansion module port
- Heatsink mounting holes
This patch adds defconfig and dts files for this board. The dts file is
the same as the one submitted for inclusion in Linux, with some minor
revisions to match the dtsi file and old EMAC bindings in U-boot.
Since the OTG controller is wired to a USB host port, and the H3 has
proper USB hosts to handle host mode, the MUSB driver is not enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
I did not enable SDMA when I added sdhci-cadence support because LD20
boards are equipped with a large amount memory beyond 32 bit address
range, but SDMA does not support the 64bit address. U-Boot relocates
itself to the end of effectively available RAM. This would make the
MMC enumeration fail because the buffer for EXT_CSD allocated in the
stack would go too high, then SDMA would fail to transfer data.
Recent SDHCI-compatible controllers support ADMA, but unfortunately
U-Boot does not support ADMA.
In the previous commit, I hided the DRAM area that exceeds the 32 bit
address range. Now, I can enable CONFIG_MMC_SDHCI_SDMA.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Enable CONFIG_CMD_PART item, as default environment requires it
and complains this command in unknown.
Signed-off-by: Andrey Zhizhikin <andrey.z@gmail.com>
The current default environment of the cm_fx6 is not suitable for
booting modern distributions.
Instead of extending the custom environment, let's use the distro
boot command, which has been developed for precisely this use case.
If the distro boot command fails, fall back to the old behavior
(except for USB drives where the old behaviour is completely covered
by the distro boot command). That way it is still possible to create
"rescue SD cards" for old installations (e.g. if one messes up the
on-flash environment).
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The Rockchip-released ATF for the Firefly apparently (i.e. Kever
reported this) does not tolerate a FDT being passed as the platform
parameter and will run into a hard stop.
To work around this limitation in the ATF parameter handling, we
enable SPL_ATF_NO_PLATFORM_PARAM (which will force passing NULL for
the platform parameters).
Note that this only affects this platform, as the ATF releases for the
RK3368 and RK3399 have always either ignored the platform parameter
(i.e. before the FDT-based parameters were supported) or support
receiving a pointer to a FDT.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This is a virtual "board" that uses configuration files and
Kconfig to define the memory layout used by a real board during
the board bring-up process.
It generates an SPL image that can be loaded using imx_usb or
SB_LOADER.exe.
When run, it will generate a set of calibration constants for
use in either or both a DCD configuration file for boards that
use u-boot.imx or struct mx6_mmdc_calibration for boards that
boot via SPL.
In essence, it is a configurable, open-source variant of the
Freescale ddr-stress tool.
https://community.nxp.com/docs/DOC-105652
File mx6memcal_defconfig configures the board for use with
mx6sabresd or mx6qsabreauto.
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Commit b6251db8c3 ("Kconfig: Introduce USE_BOOTCOMMAND and migrate
BOOTCOMMAND") removed CONFIG_BOOTCOMMAND option from
include/configs/am335x_evm.h file. But that option wasn't added to
defconfig files for BeagleBone Black board.
Because of this we can't boot Linux from SD card using just
"run bootcmd", getting next error:
** File not found /boot/undefined **
That's because "fdtfile" variable has "undefined" value by default, and
"bootcmd" doesn't call "run findfdt" command, which assigns "fdtfile" to
correct device tree file for current board name (obtained from EEPROM).
So we are forced to either call "run findfdt" command manually, or
assign manually "fdtfile=am335x-boneblack.dtb" (e.g. in uEnv.txt file).
Bring back CONFIG_BOOTCOMMAND to BBB defconfigs so that we can boot
Linux rootfs from SD card automatically without any addition actions.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
This commit updates the configuration files needed to support OF_CONTROL
on the OMAP3 EVM baseboard.
Additionally:
- CONFIG_SYS_THUMB_BUILD is enabled
- CONFIG_SPL_ENV_SUPPORT is enabled
Tested using GCC 7.2.0 [--with-float=hard --with-mode=thumb].
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
In commit 6e6cf015e7 ("Merge
git://www.denx.de/git/u-boot-imx") the line defining spl_sd
configuration for wandboard was removed, which resulted in no SPL
target being built.
Add it back.
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Currently the MX6SL option is selected via CONFIG_SYS_EXTRA_OPTIONS,
but it is better to select it directly via Kconfig.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Currently only imx6sx-sdb.dtb is loaded, but if revA board is used the
correct dtb is imx6sx-sdb-reva.dtb, so make this possible.
While at it, remove an extra 'mmc dev'.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
NXP development boards based on i.MX6/i.MX7 contain the board
revision information stored in the fuses.
Introduce a common function that can be shared by different boards and
convert mx6sabreauto to use this new mechanism.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Commit 5248930ebf ("dm: imx: cm_fx6: Enable more driver model support")
enabled driver model support for USB. But it missed to enable driver
model support for keyboards. As a result, USB keyboards do no longer
work.
Fix this by enabling driver model support for keyboards.
Fixes: 5248930ebf ("dm: imx: cm_fx6: Enable more driver model support")
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In order to provide a consistent user experience for imx board users,
remove the custom CONFIG_BOOTDELAY values from defconfig files, so that
all boards can use the default two second delay.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Freescale (NXP) boards have lots of defconfig files per board.
I used "imply PANIC_HANG" for them.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Now FASTBOOT_FLASH is auto select for sunxi platform,
so drop explicit addition.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
fpga:
- Enable loading bitstream via fit image for !xilinx platforms
zynq:
- Fix SPL SD boot mode
zynqmp:
- Not not reset in panic
- Do not use simple allocator because of fat changes
- Various dt chagnes
- modeboot variable setup
- Fix fpga loading on automotive devices
- Fix coverity issues
test:
- Fix env test for !hush case - Stephen's patch
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlo3tMgACgkQykllyylKDCFQvQCfeFgaC/95gx9orLrHxpDx7s46
wwYAmwSoXn6hc9bEzgKIppQHblzfqGU6
=mscK
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2018.01-rc2-v2' of git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2018.01-rc2-v2
fpga:
- Enable loading bitstream via fit image for !xilinx platforms
zynq:
- Fix SPL SD boot mode
zynqmp:
- Not not reset in panic
- Do not use simple allocator because of fat changes
- Various dt chagnes
- modeboot variable setup
- Fix fpga loading on automotive devices
- Fix coverity issues
test:
- Fix env test for !hush case - Stephen's patch
Enable SPL_FIT_GENERATOR with path for it.
With this patch you can get u-boot.itb for rk3399-firefly with:
> make u-boot.itb
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Only rk3399 atf need ROCKCHIP_SPL_RESERVE_IRAM. This commit updates
its default setting to 0 so that other SoCs do not need to define it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Dont use 4K sector erase by default, Disabling this
would use 64K sector erase and decreases erase time.
Also disabled by the fact that UBIFS and JFFS2 won't work
with 4K sector erase.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enabling all spi flashes because some of these boards can have different
flashes compared to public version.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This was caused by: "fs/fat: Reduce stack usage"
(sha1:2460098cffacd18729262e3ed36656e6943783ed) which converted
fat code to use malloc. But simple malloc is not freeing space
that's why full malloc implementation is needed.
Malloc space is added to RAM.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is fixing two issues:
1. Insufficient stack size for fat fs buffers
2. Insufficient space in malloc area
Tested on zc702 and zc706.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Include common config_distro_defaults.h and config_distro_bootcmd.h
for u-boot enviroments to support automatical distro boot which
scan boot.scr from external storage devices(e.g. SD and USB)
and execute autoboot script.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Include common config_distro_defaults.h and config_distro_bootcmd.h
for u-boot enviroments to support automatical distro boot which
scan boot.scr from external storage devices(e.g. SD and USB)
and execute autoboot script.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The SPL-OS partition is 0x20000, so let's make
CONFIG_CMD_SPL_WRITE_SIZE same size. This should allow for better
falcon mode operation.
Signed-off-by: Adam Ford <aford173@gmail.com>
Use 'imply' here liberally to avoid the combinatorial explosion of
defconfig changes in the PowerPC boards.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Add bits to support yet another board, the R8A77995 D3 Draak.
The DT file is from Linux 4.15-rc1 , commit
b35334447513c14a4dd55a67c269a743d4a4824b .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add bits to support yet another board, the R8A77970 V3M Eagle.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The TBS Tablet sports an LVDS display, an eMMC, an external SD, USB devices
and USB OTG.
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable all logging features on sandbox so that the tests can be run.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We cannot use sandbox memory at 0 since other things use memory at that
address. Move it up out of the way.
Note that the pre-console buffer is currently disabled with sandbox, but
this change will avoid confusion if it is manually enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
The A33-OLinuXino defconfig was using the default CONS_INDEX value for
A33, which actually points to the R_UART, which is routed to the GPIO
header without proper pull-ups or diodes. The board has a separate
header for UART0, which are routed to pins PB0 and PB1. This header
is properly marked and is likely the first pins any user would try
to get a console.
Fix CONS_INDEX in the defconfig so the console appears on UART0.
Fixes: ca5c37026b ("sunxi: Add support for A33-OLinuXino board")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
>From revision J the board uses new phy chip LAN8710. Compared
with RTL8201, RA17 pin is TXERR. It has pullup which causes phy
not to work. To fix this PA17 is muxed with GMAC function. This
makes the pin output-low.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Adds config CONFIG_FSL_LS_PPA and CONFIG_FSL_CAAM in
LS2080AQDS and LS2080ARDB secure boot defconfig.
Removes CONFIG_FIT, as with CONFIG_FSL_LS_PPA enabled,
CONFIG_FIT is selected.
Removes CONFIG_SPL_RSA as in NOR boot SPL boot is not done.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add the secure boot defconfigs for QSPI boot on LS1088ARDB
and LS1088AQDS platforms.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Unset USE_BOOTCOMMAND for all ls1088 defconfig files to fix
redefinition error. USE_BOOTCOMMAND was introduced in commit
b6251db8c3 ("Kconfig: Introduce USE_BOOTCOMMAND and migrate
BOOTCOMMAND").
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Odroid HC1 board is based on Odroid XU4 board, but it has no HDMI,
no eMMC, no build-in USB3.0 hub, no extension port pins, and no GPIO
button. USB3.0 ports are used for build-in JMicron USB to SATA bridge
and Gigabit R8152 ethernet chips. HC1 uses only passive cooling.
This patch also updates Odroid's ADCmax array and reduces ADC tolerance
to 1% to ensure that XU4 and HC1 revisions are properly detected.
I've tested this with XU3, XU3-lite, XU4 and HC1 boards. In case of my test
boards I got following values from ADC register: 372, 370, 1281 and 1313.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
[primary] Check MMC 0:1 for /extlinux/extlinux.conf and boot
[fallback 1] Check MMC 0:1 zImage and run mmcbootz
[fallback 2] Check MMC 0:1 uImage and run mmcboot
[fallback 3] Check NAND partitions and run nandboot
If 'extlinux.conf' is not found on MMC 0, the previous boot behavior is
followed.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
As discussed at [1], the Amlogic Meson GX SoCs can embed a BL31 firmware
and a secondary BL32 firmware.
Since mid-2017, the reserved memory address of the BL31 firmware was moved
and grown for security reasons.
But mainline U-Boot and Linux has the old address and size fixed.
These SoCs have a register interface to get the two firmware reserved
memory start and sizes.
This patch adds a dynamic reservation of the memory zones in the device tree bootmem
reserved memory zone used by the kernel in early boot.
To be complete, the memory zones are also added to the EFI reserved zones.
Depends on patchset "Add support for Amlogic GXL Based SBCs" at [2].
[1] http://lists.infradead.org/pipermail/linux-amlogic/2017-October/004860.html
[2] http://lists.infradead.org/pipermail/linux-amlogic/2017-November/005410.html
Changes since v1:
- switched the #if to if(IS_ENABLED()) to compile all code paths
- renamed function to meson_board_add_reserved_memory()
- added a mem.h header with comment
- updated all boards ft_board_setup()
Changes since RFC v2:
- reduced preprocessor load
- kept Odroid-C2 static memory mapping as exception
Changes since RFC v1:
- switch to fdt rsv mem table and efi reserve memory
- replaced in_le32 by readl()
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[trini: Fix warning on khadas-vim over missing <asm/arch/mem.h>
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds platform code for the Khadas VIM board based on a
Meson GXL (S905X) SoC with the Meson GXL configuration.
This initial submission supports UART, MMC/SDCard and Ethernet with the
Internal RMII PHY.
The meson-gxl-s905x-khadas-vim.dts is synchronised from the linux 4.13
stable tree as of 4.13.8.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This adds platform code for the Libre Computer CC "Le Potato" board based on a
Meson GXL (S905X) SoC with the Meson GXL configuration.
This initial submission supports UART, MMC/SDCard and Ethernet with the
Internal RMII PHY.
The meson-gxl-s905x-libretech-cc.dts is synchronised from the linux 4.13
stable tree as of 4.13.8.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Enable board config for evb-rk3128.
Serial output and eMMC works in this version.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Rework the ULCB CPLD driver and make it into a sysreset driver,
since that is what the ULCB CPLD driver is mostly for.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Adjust VGA rom address to 0xfffb0000 so that u-boot.rom image
can be built again.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
This board is based on the Atmel sama5d3 eval boards.
Supporting the following features:
- Boot from NAND Flash
- Ethernet
- FIT
- SPL
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
This board is based on the Atmel 9x5 eval board.
Supporting the following features:
- Boot from NAND Flash
- Ethernet
- FIT
- SPL
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
Add the SAMA5D2 PTC EK board and remove the SAMA5D2 PTC ENGI board
which was a prototype.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
This allows to add rcc MFD support to stm32f746-disco board
This rcc MFD driver manages clock and reset for STM32 SoCs family
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
atcspi200 is Andestech spi ip which is embedded in
AE3XX and AE250 platforms. So rename as atcspi200
will be more reasonable to be used in different
platforms.
Signed-off-by: Rick Chen <rick@andestech.com>
ATCPIT100 is Andestech timer IP which is embeded
in AE3XX and AE250 boards. So rename AE3XX to
ATCPIT100 will be more make sence.
Signed-off-by: rick <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Stop using the old ad-hoc SH I2C driver and use the new RCar IIC
driver instead. The SH I2C driver should be deprecated and removed
eventually.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Mark the PRR as u-boot,dm-pre-reloc in all Gen3 board DTs as it is
needed very early and turn on the CONFIG_SYSCON to allow the PRR
driver to bind as a syscon uclass.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This command is useless on Salvator-X as it is reading DRAM info from
SPD. We have no SPD on Salvator-X.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable the Micrel KSZ90x1 driver on ULCB, since the board is populated
with KSZ9031 and without this driver, the PHY cannot be operated.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Zynq:
- Add support for Syzygy and cc108 boards
- Add support for mini u-boot configurations (cse)
- dts updates
- config/defconfig updates in connection to Kconfig changes
- Fix psu_init handling
ZynqMP:
- SPL fixes
- Remove slcr.c
- Fixing r5 startup sequence
- Add support for external pmufw
- Add support for new ZynqMP chips
- dts updates
- Add support for zcu102 rev1.0 board
Drivers:
- nand: Support external timing setting and board init
- ahci: Fix wording
- axi_emac: Wait for bit, non processor mode, readl/write conversion
- zynq_gem: Fix SGMII/PCS support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAloeqWoACgkQykllyylKDCHO1wCggsSgQqOPdCo207FqI3yj2p0E
MYkAoI1wKvQcjGJJY19YEC1r70Op8RNo
=BqNN
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2018.01' of git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2018.1
Zynq:
- Add support for Syzygy and cc108 boards
- Add support for mini u-boot configurations (cse)
- dts updates
- config/defconfig updates in connection to Kconfig changes
- Fix psu_init handling
ZynqMP:
- SPL fixes
- Remove slcr.c
- Fixing r5 startup sequence
- Add support for external pmufw
- Add support for new ZynqMP chips
- dts updates
- Add support for zcu102 rev1.0 board
Drivers:
- nand: Support external timing setting and board init
- ahci: Fix wording
- axi_emac: Wait for bit, non processor mode, readl/write conversion
- zynq_gem: Fix SGMII/PCS support
These boards are on the boundary of "u-boot-nodtb.bin exceeds file
size limit" error.
Reduce the log-level to save memory footprint.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add configuration files/dtses for mini u-boot configurations which runs
out of OCM.
ram top is calculated from 0 that's why +#define CONFIG_SYS_SDRAM_BASE
0xfffc0000
+#define CONFIG_SYS_SDRAM_SIZE 0x40000
was hardcoded.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
cc108 board is wiring uart via PL which is good platform for SPL fpga
support.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the Zynq-based SYZYGY Hub board from Opal Kelly. The board
contains a Xilinx Zynq xc7z012s SoC, 1GB DDR3 RAM, and supports
booting from SD.
Signed-off-by: Tom McLeod <tom.mcleod@opalkelly.com>
Cc: Michal Simek <monstr@monstr.eu>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This option prevents booting on am335x_evm at least along with most
likely other platforms.
Fixes: 337bbb6297 ("spl: fit: add SPL_FIT_IMAGE_TINY config to reduce code-size")
Signed-off-by: Tom Rini <trini@konsulko.com>
Add new board names for existing board support
imx6q - icore and icore_rqs boards
imx6ul - geam6ul and isiot boards
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
mx6sxsabresd can run different kernel versions, such as NXP 4.1 or mainline.
Currently the rootfs location is passed via mmcblk number and the
problem with this approach is that the mmcblk number for the SD
card changes depending on the kernel version.
In order to avoid such issue, use the UUID method to specify the
rootfs location.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
The boot (and fallback/emergency boot) concept for the RK3399-Q7
differs from Rockchip's reference platforms.
On the RK3399-Q7, some of this functionality is present in the
bootloader itself (and configurable); some is backed in hardware by
the Qseven BIOS_DISABLE signal to invoke the final stages of fallbacks
(i.e. either an external boot bypassing on-module memories or falling
back to the BROM for USB recovery).
In summary: the ADC-based boot_mode check does not apply for the
RK3399-Q7 and we therefore disable it (in this commit) by setting
CONFIG_BOOT_MODE_REG to 0.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This tracks the SPL changes for ATF for the RK3368-uQ7:
* renames ATF_SUPPORT to ATF
* drops CONFIG_SPL_ATF_TEXT_BASE (now dynamically retrieved from
the .itb file)
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This defconfig update makes use of the new features:
* CONFIG_ROCKCHIP_SPL_RESERVE_IRAM is now set to 0, as there is no
overlap between the M0 firmware and the ATF (we load this to DRAM
and relocate it to its final location within the ATF)
* tracks the ATF_SUPPORT -> ATF renaming
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This tracks the SPL changes for ATF for the Firefly:
* renames ATF_SUPPORT to ATF
* drops CONFIG_SPL_ATF_TEXT_BASE
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently the MX6QDL option is selected via CONFIG_SYS_EXTRA_OPTIONS,
but it is better to select it directly via Kconfig.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Create board support for GE PPD, based on mx53loco.
Use mx53ppd_defconfig make target to configure for this board.
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Command run setup_emmc will create gpt partitions for mmc 0 device
based on patitions variable.
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Currently the rootfs location is passed via mmcblk number and using
the UUID method to specify the rootfs location is a better approach
working even if mmcblk number for the eMMC changes depending on the
kernel versions.
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
We first introduce CONFIG_USE_BOOTCOMMAND, similar to
CONFIG_USE_BOOTARGS. We then migrate CONFIG_BOOTCOMMAND for most
CONFIG_DISTRO_DEFAULT users. In some cases platforms have a complex
scheme around this usage, and these have been defered for the moment so
that platform maintainers can work on a migration plan.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
This patch adds support for the Internal RMII Ethernet PHY on the
Amlogic P212 Reference Board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This adds platform code for the Amlogic P212 reference board based on a
Meson GXL (S905X) SoC with the Meson GXL configuration.
This initial submission only supports UART and MMC/SDCard, support for the
internal Ethernet PHY in Work In Progress.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Beniamino Galvani <b.galvani@gmail.com>
The production variant of the SPI flash used by the clearfog
devices are based on winbond chips. Additionally enable
SPI_FLASH_BAR since some variants will have 16MB of flash
that requires this to be enabled.
Remove the default speed and mode; these values are taken from the
device tree when CONFIG_DM_SPI_FLASH is enabled.
Add default bus, so that 'sf' detects the SPI flash by default.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: remove speed/mode; add bus; move winbond to defconfig]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable the driver by default for the clearfog boards since the external
port is configured for XHCI.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: split from the SoC setup patch]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable DISTRO_DEFAULTS for
mvebu_db_armada8k_defconfig
mvebu_mcbin-88f8040_defconfig
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Distro boot support gives flexibility to run distro RFS like Ubuntu
being deployed from SD card or SATA drive. If it fails to detect
external storage, fall back to qspi/sd boot.
Enable this by default in RDB's defconfig by selecting
CONFIG_DISTRO_DEFAULTS
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Zhang Ying <zhangying@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The motivation for moving MX25 selection to Kconfig is to be
able to better handle MX25 specific errata, so that an errata option
can be selected at SoC level instead of board level.
This selection method also aligns with the way other i.MX SoCs are
selected in U-Boot.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Use default value 0x4000 for SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR instead
of define a new one.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
We move all instances of CONFIG_MTDIDS_DEFAULT and
CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files.
There's a few cases here where we need to expand upon what was in the
header file.
Tested-by: Adam Ford <aford173@gmail.com> #omap3_logic
Signed-off-by: Tom Rini <trini@konsulko.com>
The RK3368-uQ7 uses a KSZ9031 PHY on-module. Enable PHY_MICREL_KSZ90X1
in the associated defconfig.
References: da3b9e7f ("Move PHY_MICREL and PHY_MICREL_KSZ90X1 to Kconfig")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The RK3368-uQ7 uses a KSZ9031 PHY on-module. Enable PHY_MICREL_KSZ90X1
in the associated defconfig (this somehow got lost with da3b9e7f).
References: da3b9e7f ("Move PHY_MICREL and PHY_MICREL_KSZ90X1 to Kconfig")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable UMS and DFU, so that the eMMC can be accessed via the
USB gadget port on the board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Commit 001cdbbb32 ("imx: mx6slevk: enable more DM drivers") breaks
MMC support in U-Boot proper on the mx6slevk_spl_defconfig target:
U-Boot SPL 2017.09-00396-g6ca43a5 (Oct 01 2017 - 16:20:18)
Trying to boot from MMC1
U-Boot 2017.09-00396-g6ca43a5 (Oct 01 2017 - 16:20:18 -0300)
CPU: Freescale i.MX6SL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 33C
Reset cause: POR
Board: MX6SLEVK
I2C: ready
DRAM: 1 GiB
MMC: FSL_SDHC: 0
MMC Device 1 not found
*** Warning - No MMC card found, using default environment
As mx6slevk_spl_defconfig does not use CONFIG_DM_MMC and its
board file does not register the mmc controller for U-Boot proper,
let's fix this by adding CONFIG_DM_MMC=y and device tree support.
While at it, add more DM drivers, so that it becomes closer to
mx6slevk_defconfig.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
When CONFIG_DM_MMC=y, CONFIG_BLK should be selected, otherwise the
SD/eMMC card cannot be used.
Also, select CONFIG_DM_USB=y when CONFIG_USB=y to avoid build failure.
Tested on mx6slevk, mx7dsabresd and mx6ullevk.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Adam Ford <aford173@gmail.com>
Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
With latest codes on mainstream master, Intel Galileo board does not
boot unfortunately. Git biset leads to b383d6c0 "bootstage: Convert
to use malloc()".
Disable bootstage support to make it boot again. The root cause needs
to be investigated however.
Fixes: b383d6c0 ("bootstage: Convert to use malloc()")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
The Banana Pi M2-Magic is a small board with an Allwinner A33, an eMMC, a
wifi chip and some pin headers. Enable support for it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner SPI flash SPL boot support is guarded by the SPL_SPI_SUNXI
symbol. But despite its generic name, the actual only use case for this
is to provide SPI flash support to the SPL, which requires
CONFIG_SPL_SPI_FLASH_SUPPORT to be defined.
Select this symbol from the SPL_SPI_SUNXI Kconfig definition. This
avoids doing this explicitly in the defconfig, and fixes SPI booting on
the Pine64 SoPine (and -LTS version) and the OrangePi Win board (both with
SPI flash).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Remove hardcoded ftd file name from environment variables.
Use CONFIG_DEFAULT_FDT_FILE macro instead.
Signed-off-by: Michal Oleszczyk <m.oleszczyk@grinn-global.com>
I thought commit d37d31849c ("ARM: uniphier: enable DWC3 xHCI
driver") enabled CONFIG_USB_DWC3_UNIPHIER, but CONFIG_USB_XHCI_DWC3
was missing in uniphier_v7_defconfig. Re-add.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We add the various SMC91XX symbols to drivers/net/Kconfig and then this
converts the following to Kconfig:
CONFIG_SMC911X
CONFIG_SMC911X_BASE
CONFIG_SMC911X_16_BIT
CONFIG_SMC911X_32_BIT
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Apply to the rest of the tree, re-squash old and new patch]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_NAND_MXC
CONFIG_NAND_OMAP_GPMC
CONFIG_NAND_OMAP_GPMC_PREFETCH
CONFIG_NAND_OMAP_ELM
CONFIG_SPL_NAND_AM33XX_BCH
CONFIG_SPL_NAND_SIMPLE
CONFIG_SYS_NAND_BUSWIDTH_16BIT
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Finish migration of CONFIG_SPL_NAND_SIMPLE, fix some build issues,
add CONFIG_NAND_MXC so we can do CONFIG_SYS_NAND_BUSWIDTH_16BIT]
Signed-off-by: Tom Rini <trini@konsulko.com>
I've missed to add the ACPI resume support to this x86 build target.
This patch adds the ACPI resume support enabling S3 suspend /
resume.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Up to now we depended on an exported variable to build u-boot.rom.
We should be able to specify it in the configuration file, too.
With this patch this becomes possible using the new Kconfig option
CONFIG_BUILD_ROM.
This option depends on CONFIG_X86 and is selected in
qemu-x86_defconfig and qemu-x86_64_defconfig.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Adjust VGA rom address to 0xfffb0000 so that u-boot.rom image
can be built again.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This is the second batch of amazing improvements for efi_loader in 2017.11:
- New self tests to verify our own code
- A few bug fixes
- colored text support
- event and SNP improvements, should get us close to iPXE working
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=PiNi
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2017-10-13
This is the second batch of amazing improvements for efi_loader in 2017.11:
- New self tests to verify our own code
- A few bug fixes
- colored text support
- event and SNP improvements, should get us close to iPXE working
Add support for the DHCOM i.MX6 PDK board. This board has:
- FEC ethernet
- EHCI USB host
- 3x SDMMC
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
mx6slevk can run different kernel versions, such as NXP 4.1 or mainline.
Currently the rootfs location is passed via mmcblk number and the
problem with this approach is that the mmcblk number for the SD
card changes depending on the kernel version.
In order to avoid such issue, use the UUID method to specify the
rootfs location.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Latest wandboard hardware revision is revd1, which brings the following
new features:
- PFUZE100 PMIC
- AR8035 Ethernet PHY
- Upgrade Wifi/BT chip to BCM4339/BCM43430.
The detection mechanism is to probe the PMIC and when it is
found, then the revision of the board is revd1.
As the detection is done via PMIC, we need to print the board version
at a later stage via CONFIG_DISPLAY_BOARDINFO_LATE and also need
to disable CONFIG_DISPLAY_BOARDINFO, which is done much earlier.
Make the necessary adjustments for the AR8035 PHY to work on revd1.
Based on Richard Hu's work from Technexion's U-Boot tree.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Fix for finding mmc devices on i.MX6Q icore boards
added in below comment
"icorem6: Fix to find MMC devices"
(sha1: a2b137b38d)
which is reverted in during u-boot-imx merge
" Merge git://git.denx.de/u-boot-imx"
(sha1: 6aee2ab68c)
This patch, is recreated to fix merge conflict.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
CONFIG_CMD_BOOTZ symbol does not work in board config file
anymore, so fix this by moving it to Kconfig.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This rework the board to use the generic filesystem commands instead
of forcing the use of FAT for the boot files.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
With CONFIG_DISPLAY_CPUINFO=y we get a "Reset cause" line, which
brings important information of the reboot cause.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
The option is specified in Kconfig, but still a few config header files
are overriding the choice by #undef'ing it. Re-sync the option with
moveconfig to rid of the #undefs.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:
../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {
Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Due to a conflict with recent Primary Protected Application (PPA),
PPA cannot be loaded for SPL stage, falcon boot is not enabled by
default. With compatible PPA image, to enable falcon boot, activate
these Kconfig options in defconfig
CONFIG_SPL_FIT=y
CONFIG_SPL_FSL_LS_PPA=y
CONFIG_SPL_GZIP=y
CONFIG_SPL_LOAD_FIT=y
CONFIG_SPL_OS_BOOT=y
CONFIG_SPL_OF_LIBFDT=y
Because environment variables are not avaiable during SPL stage for
SD boot, set "boot_os=y" as default.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_CMD_BOOTZ symbol does not work in board config file
anymore, so fix this by moving it to Kconfig.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The setexpr command is useful for scripting, lets enable it for all
x86 based theadorable platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This board builds an U-Boot binary that is bootable with QEMU's 'virt'
machine on ARM. The minimal QEMU command line is:
qemu-system-arm -machine virt,highmem=off -bios u-boot.bin
(Note that the 'highmem=off' parameter to the 'virt' machine is required for
PCI to work in U-Boot.) This command line enables the following:
- u-boot.bin loaded and executing in the emulated flash at address 0x0
- A generated device tree blob placed at the start of RAM
- A freely configurable amount of RAM, described by the DTB
- A PL011 serial port, discoverable via the DTB
- An ARMv7 architected timer
- PSCI for rebooting the system
- A generic ECAM-based PCI host controller, discoverable via the DTB
Additionally, QEMU allows plugging a bunch of useful peripherals to the PCI bus.
The following ones are supported by both U-Boot and Linux:
- To add a Serial ATA disk via an Intel ICH9 AHCI controller, pass e.g.:
-drive if=none,file=disk.img,id=mydisk -device ich9-ahci,id=ahci -device ide-drive,drive=mydisk,bus=ahci.0
- To add an Intel E1000 network adapter, pass e.g.:
-net nic,model=e1000 -net user
- To add an EHCI-compliant USB host controller, pass e.g.:
-device usb-ehci,id=ehci
- To add a NVMe disk, pass e.g.:
-drive if=none,file=disk.img,id=mydisk -device nvme,drive=mydisk,serial=foo
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
CONFIG_FIT_EMBED might be confused with CONFIG_OF_EMBED, rename it
MULTI_DTB_FIT as it is able to get a DTB from a FIT image containing
multiple DTBs. Also move the option to the Kconfig dedicated to the DTS
options and create a README for this feature.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The EFI selftest has been broken by a patch on efi-next.
We should enable CONFIG_CMD_BOOTEFI_SELFTEST on
qemu-x86_defconfig and qemu-x86_64_defconfig by default
to catch this type of problem in the Travis CI tests.
These systems typically have abundant memory so that
enabling this option should not pose a problem.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
While this came in with a default value of 6 I am lowering this to 4.
The MTD/UBI code has a large number of error messages that we include
now. In addition, "normally" warning messages are not included so this
feels like a more natural level to have.
Signed-off-by: Tom Rini <trini@konsulko.com>
When we import code from Linux, with regular re-sync planned, we want
to use printk() and pr_*(). U-Boot does not support them in a clean
way. So, people end up with local macros, or compat headers here and
there, then we occasionally see build errors of definition conflicts.
We have include/linux/compat.h, but putting all sorts of unrelated
things into a single header is just a temporal workaround. Hence this
patch, to find the best home for all printk variants. If you want to
use printk() and friends, please include <linux/printk.h>. This header
is self-contained, and pulls in only a few headers.
When I was testing this clean-up, I noticed the image size exceeded
its platform limit on some boards. This is because all pr_*() that
were previously defined as no-op in include/linux/mtd/mtd.h (unless
CONFIG_MTD_DEBUG is set), are now enabled.
To make such boards happy, this commit also implements CONFIG_LOGLEVEL.
The concept is similar to the kernel parameter "loglevel". (Actually,
the Kconfig help message was taken from kernel-paremeter.txt of Linux)
Messages with a loglevel smaller than console loglevel will be printed.
The difference is the loglevel is build-time determined. To save the
image size, lower priority pr_*() are compiled out. I set the default
of CONFIG_LOGLEVEL to 6, i.e. pr_notice and higher priority messages
are compiled in.
I adjusted CONFIG_LOGLEVEL to avoid build error for some boards.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Add in SPL_LOGLEVEL that is the same as LOGLEVEL]
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable pinconf since it's now implemented and used in the DTs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Banana Pi M1 Plus is an open-source single-board computer
that adds more connectivity to the classic board using
Allwinner A20 SOC.
Bananapi M1-Plus features:
- A20 Dual-core 1.0GHz
- 1 GB DDR3 SDRAM
- MicroSD
- 10/100/1000 Ethernet RJ45
- WiFi b/g/n
- 5V DC Micro USB power-supply
For dts file,
Sync with Linux commit f92ca09("Merge branch 'akpm/master'").
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
As we have already DRAM initialization code for V3s SoC, we can
defaultly enable SPL now on Lichee Pi Zero.
Add CONFIG_SPL in Lichee Pi Zero defconfig.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Set CONFIG_MMC_SUNXI_SLOT_EXTRA=2 to enable the eMMC controller to
access eMMC on the board.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The upstream (Linux) device tree file for the Bananapi M3 follows the
convention of using the well known brand name, instead of the vendor
name, for naming. The file was recently added to upstream in commit
359b5a1e1c2d ("ARM: sun8i: a83t: Add device tree for Sinovoip Bananapi
BPI-M3")
Rename the device tree file in U-boot to match.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The current code, if there's both an eMMC and an MMC slot available on the
board, will swap the MMC indices based on whether we booted from the eMMC
or the MMC. This way, the MMC we're supposed to boot on will always have
the index 0.
However, this causes various issues, for example when using other
components that base their behaviour on the MMC index, such as fastboot.
Let's remove that hack, and take the opposite approach. The MMC will always
have the same index, but the bootcmd will pick the same device than the one
we booted from. This is done through the introduction of the mmc_bootdev
environment variable that will be filled by the board code based on the
boot device informations we can get from the SoC.
In order to not introduce regressions, we also need to adjust the fastboot
MMC device and the environment device in order to set it to the eMMC, over
the MMC, like it used to be the case.
Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
From rev.J A20-OLinuXino-MICRO has eMMC option. For now this is
only 4GB, but in the future size may increase.
The dts file is the same from mainline kernel.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
CONFIG_RANDOM_UUID is used by the GPT command to generate random UUID when
none are provided.
Move that option to Kconfig.
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fastboot need a bunch of options to be operating properly, such as the
g_dnl gadget, the fastboot command, and some options that make sense. Since
fastboot is now part of Kconfig, make sure we have them right.
That will also reduce the boilerplate in the defconfigs.
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A good number of our boards have USB_GADGET enabled. Imply it so that all
the boards can benefit from it, and remove some boilerplate from our
defconfigs.
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
All the Allwinner boards use the same manufacturer, VID and PID for the
gadgets. Make them the defaults to remove some boilerplate from our
defconfigs.
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The usb_ether gadget duplicates the USB settings for the manufacturer,
product ID and vendor ID.
Make sure we use the common option so that we can expect a single VID/PID
couple for a single device.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The g_dnl USB settings for the vendor ID, product ID and manufacturer are
actually common settings that can and should be shared by all the gadgets.
Make them common by renaming them, and convert all the users.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
We need to select an interface for the usb_ether gadget, and they haven't
been converted to Kconfig yet. Add a choice to make sure we have an option
selected, and convert all the users.
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The USB Ethernet gadget option has not yet been moved to Kconfig, let's
deal with that.
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
While the USB Ethernet device address is already defined in Kconfig, the
host address isn't. Convert it.
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The RK3399-Q7 requires DM regulator support in SPL, so we can use the
regulator framework to reenable the eMMC and SPI, if these had been
turned of by the BIOS_DISABLE signal.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add defconfig for rk8xx and regulator and i2c controller.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
