The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Rename disk_partition_type_uuid to disk_partition_type_guid.
Provide function descriptions for the getter and setter.
Fixes: bcd645428c ("part: Add accessors for struct disk_partition type_uuid")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To avoid confusion document that timer_dev_priv.clock_rate and
timer_get_rate() yield the timer rate in hertz.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Drop unused macro. This was copied straight from the AM62x EVM but while
meant for a second region of DDR this is not even needed for the AM62x
EVM configurations and has meanwhile also been dropped there.
Note that on the Verdin AM62, we do auto-detect the amount of SDRAM.
While at it also update the comment noting that CFG_SYS_SDRAM_SIZE is
the maximum which is only used for such auto-detection.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
ti_mmc bootmethod uses a findfdt routine that is expected to be
implemented by all platforms.
Define a default findfdt based on configured DEFAULT_DEVICE_TREE option
for u-boot. This saves duplication across multiple boards and handles
architecture folder location changes centrally.
TI ARMV7 platforms will need to override default_device_tree_subarch
in the env file to point to the appropriate platform. Note: default
"omap" is used to cater to "most common" default.
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
ti_armv7_common does not make any more sense as it is used by armv7
and armv8 TI based platforms.
Reported-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Now that BOOTSTD is used by default, drop un-used header file
inclusion.
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Wrap the distro_boot options with CONFIG_DISTRO_DEFAULTS.
This is an intermediate step for us to switch over to
CONFIG_BOOTSTD_DEFAULTS and drop this section in follow on patches.
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Drop unused macro. This was meant for a second region of DDR which we
do not need for AM62x evm configurations.
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
'script' bootmethod that should be used with CONFIG_BOOTSTD.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
If mmc dev reports that the device is not present, there is no point in
proceeding further to attempt to load the files.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
spl_invoke_opensbi function is not returned to SPL. Thus, we need to
set __noreturn function attribute.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This platform is behind on migrations (it is the sole user of the oldest
legacy version of the USB gadget stack and is long overdue for
migration) and with Pali no longer being a maintainer, we remove this
platform.
Signed-off-by: Tom Rini <trini@konsulko.com>
After the merge of v2023.10-rc4 to next include/event.h needs to be
fully documented in order for documentation builds to complete. Rewords
two of the event_t descriptions to be docbook style and better match the
rest of this enum. Fix two typos (flag->flags) in other comments.
Signed-off-by: Tom Rini <trini@konsulko.com>
Drop use of the distro scripts and use standard boot instead.
We don't need to specify the mmc devices individually, since they are
used in order from 0 to 2, and standard boot uses that order anyway.
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide Sphinx documentation for all events.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a new event which handles this function. Convert existing use of
the function to use the new event instead.
Make sure that EVENT is enabled by affected boards, by selecting it from
the LAST_STAGE_INIT option. For x86, enable it by default since all boards
need it.
For controlcenterdc, inline the get_tpm() function and make sure the event
is not built in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the misc_init_f event instead, which is designed for this purpose.
All boards with CONFIG_VID already enable CONFIG_EVENT.
Signed-off-by: Simon Glass <sjg@chromium.org>
Convert this to use events instead of calling a function directly in the
init sequence.
Rename it to arch_fsp_init_f() to distinguish it from the one that happens
after relocation.
For FSPv2 nothing needs to be done here, so drop the empty function.
Signed-off-by: Simon Glass <sjg@chromium.org>
The new name makes it clearer that this is for a full spy, with access to
the context and the event data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move the manual-relocation code to the initcall file. Make sure to avoid
manually relocating event types. Only true function pointers should be
relocated.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the initcall list consists of a list of function pointers. Over
time the initcall lists will likely change to mostly emitting events,
since most of the calls are board- or arch-specific.
As a first step, allow an initcall to be an event type instead of a
function pointer. Add the required macro and update initcall_run_list() to
emit an event in that case, or ignore it if events are not enabled.
The bottom 8 bits of the function pointer are used to hold the event type,
with the rest being all ones. This should avoid any collision, since
initcalls should not be above 0xffffff00 in memory.
Convert misc_init_f over to use this mechanism.
Add comments to the initcall header file while we are here. Also fix up
the trace test to handle the change.
Signed-off-by: Simon Glass <sjg@chromium.org>
Somehow I do not see any inlining with initcalls now. I was sure I saw
it when this commit went in, but now it seems to make things worse.
This reverts commit 47870afab9.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current event spy is always passed the event context and the event.
The context is always NULL for a static spy. The event is not often used.
Introduce a 'simple' spy which takes no arguments. This allows us to drop
the adaptation code that many of these spy records use.
Update the event script to find these in the image.
Signed-off-by: Simon Glass <sjg@chromium.org>
Perform all the block device creation only once, after the driver itself
successfully bound. Do not do this in uclass post bind, as this might be
triggered multiple times. For example the ut_dm_host test triggers this
and triggers a memory leak that way, since there are now multiple block
devices created using the blk_create_devicef() .
To retain the old probe-on-boot behavior, set DM_FLAG_PROBE_AFTER_BIND
flag in uclass post_bind callback, so the driver model would probe the
driver at the right time.
Rename the function as well, to match similar functions in
other block-related subsystems, like the mmc one.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmTu+QMcHGV1Z2VuLmhy
aXN0ZXZAY29sbGFib3JhLmNvbQAKCRAesx4CDqwvyFqVB/9z5lV4zhqWYiQ+wNZL
Gxs3//DSS5iVHU+xaPRrYQT99Yn2/kfM2LeQ4REBOaOTP7IX2ewmOEro4OUViFuC
kt/WnHD0XzN+2o8akIdVC5YudgVcuX751SQtp5dqcbN6FylSH010+YIZTvaJoNQn
+Wny1ZZhpuNJJEPvLxE/eiJ3jFwvEAjC+jH328uQIeSLknPh93hGJOFc/02F0O2o
s96J1/VZ4qvvQKYw0sgNtGb/0Og7V0RLW27+RfwhH4XJvAIv/A6MioTyRaCS2h7H
tzj/hFXbzGtu+AqrEtMgNjzC7vAx+0266P/Zx/DOWKoWLDIYkWSLpYKLut0E6CUe
+fcB
=L/iw
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2023.10-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2023.10 cycle:
This feature set includes a new board sama5d29 Curiosity, and various
fixes and alignments for sam9x60 and sam9x60 curiosity board.
Support has been added for generating the EFI capsules through
binman. Make changes in the EFI capsule update testing feature to
generate capsules through binman.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Some bootmeths support scanning a partition without a filesystem on it.
Add a flag to support this.
This will allow the ChromiumOS bootmeth to find kernel partition, which
are stored in a special format, without a filesystem.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some pytests create files in the persistent-data directory. It is useful
to be able to access these files in C tests. Add a function which can
locate a file given its leaf name, using the environment variable set
up in test/py/conftest.py
Signed-off-by: Simon Glass <sjg@chromium.org>
These should be in the header file for easy browsing, not in the source
code. Move them and add a missing Return on one of the functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
This field is only present when a CONFIG is set. To avoid annoying #ifdefs
in the source code, add an accessor. Update the only usage.
Note that the accessor is optional. It can be omitted if it is known that
the option is enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
This field is only present when a CONFIG is set. To avoid annoying #ifdefs
in the source code, add accessors. Update all code to use it.
Note that the accessor is optional. It can be omitted if it is known that
the option is enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
This field is only present when a CONFIG is set. To avoid annoying #ifdefs
in the source code, add accessors. Update all code to use it.
Note that the accessor is optional. It can be omitted if it is known that
the option is enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
The dev_ prefix is a hangover from the pre-driver model days. The device
is now a different thing, with driver model. Update the partition code to
just use 'desc', as is done with driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a command to read edit settings from CMOS RAM, using the cedit
definition to indicate which registers and bits are used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a command to write cedit settings to CMOS RAM so that it can be
preserved across a reboot. This uses a simple bit-encoding, where each
field has a 'bit position' and a 'bit length' in the schema.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a command to read cedit settings from environment variables so that
they can be restored as part of the environment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a command to write cedit settings to environment variables so that
they can be stored with 'saveenv'.
Signed-off-by: Simon Glass <sjg@chromium.org>
Support writing settings from an expo into a file in FDT format. It
consists of a single node with a two properties for each sceneitem,
one with tag ID chosen by the user and another for its text value.
Signed-off-by: Simon Glass <sjg@chromium.org>
Split out the code which prepares the cedit for use, so we can call it
from a test.
Add a log category while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Before adding more functions to this interface, create a new header for
the configuration editor.
Fix up the expo header guard while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some devices have limited DMA capabilities and require that the
buffers passed to them fit specific properties. Add new optional
callback which can be used at driver level to indicate whether a
buffer alignment is suitable for the device DMA or not. This is
a pass-through callback from block uclass to drivers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Some devices have limited DMA capabilities and require that the
buffers passed to them fit specific properties. Add new optional
callback which can be used at driver level to indicate whether a
buffer alignment is suitable for the device DMA or not, and
trigger use of generic bounce buffer implementation to help use
of unsuitable buffers at the expense of performance degradation.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Move the macro into blk-uclass.c , since it is only used there.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move part_create_block_devices() to blk uclass and unexpose
the function. This can now be internal to the block uclass.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This patch introduces EVT_DM_POST_INIT_R event type for handling hooks
after relocation.
Fixes: 55171aedda ("dm: Emit the arch_cpu_init_dm() even only before relocation")
Suggested-by: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Tested-by: Milan P. Stanić <mps@arvanta.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Roland Ruckerbauer <mail@ruabmbua.dev>
Tested-by: Roland Ruckerbauer <mail@ruabmbua.dev>
Fixed missing event name in event.c:
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds support for various new Tegra30 boards (ASUS, LG and HTC) and
has some other minor enhancements, such as enabling the poweroff command
on several Tegra210 and Tegra186 boards.
-----BEGIN PGP SIGNATURE-----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=Bzgn
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-2023.10-rc1' of https://source.denx.de/u-boot/custodians/u-boot-tegra
ARM: tegra: Changes for v2023.10-rc1
This adds support for various new Tegra30 boards (ASUS, LG and HTC) and
has some other minor enhancements, such as enabling the poweroff command
on several Tegra210 and Tegra186 boards.
Since ARMv5, the clz instruction allows for efficient implementation of
ffs/fls with builtins. Until ARMv7 (with Thumb-2), this instruction is
only available in ARM mode. LTO makes it difficult to force specific
functions to be in ARM mode, as it is effectively a form of very
aggressive inlining. To work around this, fls/ffs are implemented in
assembly for ARMv5 and ARMv6 when compiling U-Boot in Thumb mode.
Overall, this saves around 75 bytes per call.
This code is synced with v5.15 of the Linux kernel.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Display the STMicroelectronics logo with features VIDEO_LOGO and
SPLASH_SCREEN on STMicroelectronics boards.
With CONFIG_SYS_VENDOR = "st", the logo st.bmp is selected, loaded at the
address indicated by splashimage and centered with "splashpos=m,m".
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
board_get_usable_ram_top() returns a physical address that is stored in
gd->ram_top. The return type of the function should be phys_addr_t like the
current type of gd->ram_top.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
* Convert comments in part.h to Sphinx style.
* Create documentation page for the partition API.
* Add the partition API page to the API index page.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Improve the description of function board_get_usable_ram_top().
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
* provide a description for function lmb_is_reserved()
* improve the description of funciton lmb_is_reserved_flags()
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
- Assorted PCI-related fixes, add Apple Type-C PHY support, semihosting
updates, fix a FAT corner-case, update the help on the pxe cmd and
clean up the gpio uclass slightly.
The current gpio-uclass design uses name field in struct gpio_dev_priv as
an indicator that GPIO is claimed by consumer. This overloads the function
of name field and does not work well for named pins not configured as GPIO
pins.
Introduce separate bitfield array as the claim indicator.
This unbreaks dual-purpose AF and GPIO operation on STM32MP since commit
2c38f7c318 ("pinctrl: pinctrl_stm32: Populate uc_priv->name[] with pinmux node's name")
where any pin which has already been configured as AF could no longer be
claimed as dual-purpose GPIO. This is important for pins like STM32 MMCI
st,cmd-gpios .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add fdtoverlay_addr_r and enable OF_LIBFDT_OVERLAY for the
use of DT overlay in RV1126.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Support booting ChromiumOS on ARM devices using FIT. Add an entry into the
boot implementation which does not require a command line. This can be
expanded over time as the bootm code is refactored.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some bootflows (such as EFI and ChromiumOS) delay reading the kernel until
it is needed to boot. This saves time when scanning and avoids needing to
allocate memory for something that may never be used.
To permit reading of these files, add a new 'bootflow read' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide an option to dump this information if available.
Move the funciion prototype to the common x86 header. Allow the command
line to be left out since 'bootflow info' show this itself and it is
not in the correct place in memory until the kernel is actually booted.
Fix a badly aligned heading while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some bootmeths need to store their own information related to the
bootflow, in addition to the generic information in struct bootflow.
Add a pointer for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to avoid using #ifdefs around header files and in the code. It
makes sense to collect the various functions used for loading images into
a single header which can be included by all architectures. The best place
for this is the arch-neutral bootm.h header, so use that.
Move some zimage functions into this bootm.h header.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the common include.
Drop everything from the config.h file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # Intel Edison
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use the common include.
Drop everything from the config.h file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # Intel Edison
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use the common include. Drop the unnecessary changes, since missing
stdio drivers will be ignored.
Drop everything from the config.h file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # Intel Edison
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use the common include along with some additions.
Drop everything from the config.h file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # Intel Edison
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[Drop common env from slimbootloader.env]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Use the common include along with some additions.
Drop everything from the config.h file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # Intel Edison
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use the common include. The existing environment includes "vga" but that
is not valid anymore, so let it use vidconsole
Drop everything from the config.h file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # Intel Edison
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use the common include.
Drop everything from the config.h file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # Intel Edison
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use the common include.
Drop everything from the config.h file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # Intel Edison
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use the common include.
Drop everything from the config.h file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # Intel Edison
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use the common include.
Drop everything from the config.h file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # Intel Edison
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use the common include and add some options specific to this board.
Drop everything from the config.h file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # Intel Edison
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Create a text-file version of x86-common.h which can be used by x86
boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # Intel Edison
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
No x86 board uses distro boot, so drop these settings.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # Intel Edison
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is not needed in this file anymore. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # Intel Edison
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This should be included by files that need it, not the config.h file.
Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # Intel Edison
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is only used in one file and the value is the same for both boards
which define it. Use the fixed value of 32KB and drop the CFG. This will
allow removal of the config.h files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # Intel Edison
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The 'environment' word is too long. We mostly use 'env' in U-Boot, so use
that as the name of the include directory too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # Intel Edison
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This name is a little confusing since it suggests that it sets up the
sibling block device. In fact it sets up a bootdev for it. Rename the
function to make this clearer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
When USB finds no devices it currently returns -EPERM which bootstd does
not understand. This causes other bootdevs of the same priority to be
skipped.
Fix this by returning the correct error code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
1. Convert all linker symbols to char[] type so that we can get the
corresponding address by calling array name 'var' or its address
'&var'. In this way, we can avoid some potential issues[1].
2. Remove unused symbol '_TEXT_BASE'. It has been abandoned and has
not been referenced by any source code.
3. Move '__data_end' to the arch x86's own sections header as it's
only used by x86 arch.
4. Remove some duplicate declared linker symbols. Now we use the
standard header file to declare them.
[1] This patch fixes the boot failure on MIPS target. Error log:
SPL: Image overlaps SPL
Fixes: 1b8a1be1a1 ("spl: spl_legacy: Fix spl_end address")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The VNBYTES() macro needs to have parentheses to prevent some (harmless)
macro expansion bugs. The VNBYTES() macro is used like this:
VID_TO_PIXEL(x) * VNBYTES(vid_priv->bpix)
The * operation is done before the / operation. It still ends up with
the same results, but it's not ideal.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add MM communication support using FF-A transport
This feature allows accessing MM partitions services through
EFI MM communication protocol. MM partitions such as StandAlonneMM
or smm-gateway secure partitions which reside in secure world.
An MM shared buffer and a door bell event are used to exchange
the data.
The data is used by EFI services such as GetVariable()/SetVariable()
and copied from the communication buffer to the MM shared buffer.
The secure partition is notified about availability of data in the
MM shared buffer by an FF-A message (door bell).
On such event, MM SP can read the data and updates the MM shared
buffer with the response data.
The response data is copied back to the communication buffer and
consumed by the EFI subsystem.
MM communication protocol supports FF-A 64-bit direct messaging.
We tested the FF-A MM communication on the Corstone-1000 platform.
We ran the UEFI SCT test suite containing EFI setVariable, getVariable and
getNextVariable tests which involve FF-A MM communication and all tests
are passing with the current changes.
We made the SCT test reports (part of the ACS results) public following the
latest Corstone-1000 platform software release. Please find the test
reports at [1].
[1]: https://gitlab.arm.com/arm-reference-solutions/arm-reference-solutions-test-report/-/tree/master/embedded-a/corstone1000/CORSTONE1000-2023.06/acs_results_fpga.zip
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Tested-by: Gowtham Suresh Kumar <gowtham.sureshkumar@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Emulate Secure World's FF-A ABIs and allow testing U-Boot FF-A support
Features of the sandbox FF-A support:
- Introduce an FF-A emulator
- Introduce an FF-A device driver for FF-A comms with emulated Secure World
- Provides test methods allowing to read the status of the inspected ABIs
The sandbox FF-A emulator supports only 64-bit direct messaging.
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add Arm FF-A support implementing Arm Firmware Framework for Armv8-A v1.0
The Firmware Framework for Arm A-profile processors (FF-A v1.0) [1]
describes interfaces (ABIs) that standardize communication
between the Secure World and Normal World leveraging TrustZone
technology.
This driver uses 64-bit registers as per SMCCCv1.2 spec and comes
on top of the SMCCC layer. The driver provides the FF-A ABIs needed for
querying the FF-A framework from the secure world.
The driver uses SMC32 calling convention which means using the first
32-bit data of the Xn registers.
All supported ABIs come with their 32-bit version except FFA_RXTX_MAP
which has 64-bit version supported.
Both 32-bit and 64-bit direct messaging are supported which allows both
32-bit and 64-bit clients to use the FF-A bus.
FF-A is a discoverable bus and similar to architecture features.
FF-A bus is discovered using ARM_SMCCC_FEATURES mechanism performed
by the PSCI driver.
Clients are able to probe then use the FF-A bus by calling the DM class
searching APIs (e.g: uclass_first_device).
The Secure World is considered as one entity to communicate with
using the FF-A bus. FF-A communication is handled by one device and
one instance (the bus). This FF-A driver takes care of all the
interactions between Normal world and Secure World.
The driver exports its operations to be used by upper layers.
Exported operations:
- ffa_partition_info_get
- ffa_sync_send_receive
- ffa_rxtx_unmap
Generic FF-A methods are implemented in the Uclass (arm-ffa-uclass.c).
Arm specific methods are implemented in the Arm driver (arm-ffa.c).
For more details please refer to the driver documentation [2].
[1]: https://developer.arm.com/documentation/den0077/latest/
[2]: doc/arch/arm64.ffa.rst
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
convert UUID string to little endian binary data
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
add support for x0-x17 registers used by the SMC calls
In SMCCC v1.2 [1] arguments are passed in registers x1-x17.
Results are returned in x0-x17.
This work is inspired from the following kernel commit:
arm64: smccc: Add support for SMCCCv1.2 extended input/output registers
[1]: https://documentation-service.arm.com/static/5f8edaeff86e16515cdbe4c6?token=
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
This adds initial support for the Toradex Verdin AM62 Quad 1GB WB IT
V1.0A module and subsequent V1.1 launch configuration SKUs. They are
strapped to boot from their on-module eMMC. U-Boot supports booting
from the on-module eMMC only, DFU support is disabled for now due to
missing AM62x USB support.
The device trees were taken straight from Linux v6.5-rc1.
Boot sequence is:
SYSFW ---> R5 SPL (both in tiboot3.bin) ---> ATF (TF-A) ---> OP-TEE
---> A53 SPL (part of tispl.bin) ---> U-boot proper (u-boot.img)
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
The recovery-firmware and OpenWrt-NAND do not yet have bootflow
/bootstd entrypoints, so add bootmenu entries to make them
accessible.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The default Ten64 MTD configuration reserves two ubifs partitions
for OpenWrt residing on NAND flash. Add the bootcmd for this system
into the default environment.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The recovery environment[1] on the Ten64 is a OpenWrt-
based ramdisk stored on the NAND intended to help with
system setup tasks.
Before the bootargs were not being set for the recovery
command, relying instead on the existing bootargs variable.
Ensure the bootargs are set correctly prior to booting recovery.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[1] https://ten64doc.traverse.com.au/software/recovery/
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Change the firmware on microSD path to "firmware/traverse/ten64"
as per EBBR section 4.2[1].
The Traverse firmware tools now locate the DPAA2 firmware
and configuration files under that path on the rescue
SD card image.
If a user then installs a standard Linux
distribution over the top of that sdcard, (in theory)
it will be left alone by distribution boot tooling.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[1] https://arm-software.github.io/ebbr/index.html#firmware-partition-filesystem
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The DPAA2 DPL (data plane layout) file was previously
being loaded into 0x80300000, and set to be applied
just before hand off to the kernel.
When a FIT image with a load_address of 0x80000000 was
booted with bootm, the DPL in memory was overwritten.
Move the DPL load to 0x8E000000 (196MiB away from 0x80000000,
and below the other typical load addr of 0x90000000).
Ideally in the future, the DPL lazyapply command
("fsl_mc lazyapply DPL $dpl_addr") should be set to
load the DPL contents into a memory area owned by U-Boot.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This patch adds general board files based on MT7988 SoCs.
MT7988 uses one mmc controller for booting from both SD and eMMC,
and the pins of mmc controller booting from SD are also shared with
one of spi controllers.
So two configs are need for these boot types:
1. mt7988_rfb_defconfig - SPI-NOR, SPI-NAND and eMMC
2. mt7988_sd_rfb_defconfig - SPI-NAND and SD
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Now we use fdtdec_setup_mem_size_base() to get DRAM base from fdt ram node
and update gd->ram_base. CFG_SYS_SDRAM_BASE is unused and will be removed.
Also, since mt7622 always passes fdt to linux kernel, there's no need to
assign value to gd->bd->bi_boot_params.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
* If an error occurs in efi_disk_add_dev(), don't leak resources.
* If calloc() fails while creating the file system protocol interface,
signal an error.
* Rename efi_simple_file_system() to efi_create_simple_file_system().
* Drop a little helpful debug message.
Fixes: 2a92080d8c ("efi_loader: add file/filesys support")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The macros are prefixed with DM_FLAG_, not DM_FLAGS_.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This brings PCI xHCI support to QEMU RISC-V and uses a usb keyboard
as one of the input devices.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit 66ffe57 ("riscv: qemu: detect and boot the kernel passed by QEMU")
added some logic to handle "riscv,kernel-start" in DT and stored the
address to an environment variable kernel_start.
However this "riscv,kernel-start" has never been an upstream DT binding.
The upstream QEMU never generates such a DT either. Presumably U-Boot
development was based on a downstream QEMU fork.
Now we drop all codes in commit 66ffe57, except that BOARD_LATE_INIT
is kept for later use.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As it is only called in common/console.c
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # qemu-x86_64
ROCK 5A is a Rockchip RK3588S based SBC (Single Board Computer) by Radxa.
There are tree variants depending on the DRAM size : 4G, 8G and 16G.
Specifications:
Rockchip Rk3588S SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
4/8/16GB memory LPDDR4x
Mali G610MC4 GPU
MIPI CSI 2 multiple lanes connector
4-lane MIPI DSI connector
Audio – 3.5mm earphone jack
eMMC module connector
uSD slot (up to 128GB)
2x USB 2.0, 2x USB 3.0
2x micro HDMI 2.1 ports, one up to 8Kp60, the other up to 4Kp60
Gigabit Ethernet RJ45 with optional PoE support
40-pin IO header including UART, SPI, I2C and 5V DC power in
USB PD over USB Type-C
Size: 85mm x 56mm (Raspberry Pi 4 form factor)
Kernel commits:
d1824cf95799 ("arm64: dts: rockchip: Add rock-5a board")
991f136c9f8d ("arm64: dts: rockchip: Update sdhci alias for rock-5a")
304c8a759953 ("arm64: dts: rockchip: Remove empty line from rock-5a")
cda0c2ea65a0 ("arm64: dts: rockchip: Fix RX delay for ethernet phy on rk3588s-rock5a")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 Quartz64 Model A is a single-board computer based on the
Rockchip RK3566 SoC. The board features USB3, SATA, PCIe, HDMI, USB2.0,
CSI, DSI, eDP, eMMC, SD, and an e-paper parallel port, as well as a
20 pin GPIO header.
Features tested on a Quartz64-A 8GB v2.0 2021-04-27:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- Resync some of the K3 DTS files with the kernel, and pull in some
required related updates to keep drivers in sync with the dts files
now. Bring in some incremental fixes on top of one of the series I
applied recently as well as updating the iot2050 platform. Also do a
few small updates to the K2 platforms.
- Enable pcie support for rk3568;
- Add boards:
rk3399: Radxa ROCK 4SE;
rk3328: Orange Pi R1 Plus, Orange Pi R1 Plus LTS
rk3568: FriendlyARM NanoPi R5S/R5C, Hardkernel ODROID-M1
rk3588: Edgeble Neu6B
- support OP-TEE with binman;
- support Winbond SPI flash;
- rk3588 usbdp phy support;
- dts and config updates for different boards;
Move to using .env file for setting up environment variables for K2x_evm.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is more complex than it needs to be and makes converting these
boards over to plain text env files more difficult. Remove setting
mtdparts as the DTS already contain the partitions. While here also
drop the conflicting definitions from the K2 defconfigs.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Similar to get_fdt_mmc make get_overlays_mmc look at /boot/dtb/* path
for overlay files.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
All K3 SoCs use same set of args to load kernel for MMC. So move this to
common place to avoid duplication.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
The common env bits now come via ti_armv7_common.env, include it.
Furthermore restore the board-specific boot targets and their ordering
that is now enforced k3-wide differently. Finally, enable
CONFIG_LEGACY_IMAGE_FORMAT explicitly which got lost while turning
FIT_SIGNATURE on by default for k3 devices.
Fixes: 53873974 ("include: armv7: Enable distroboot across all configs")
Fixes: 4ae1a247 ("env: Make common bootcmd across all k3 devices")
Fixes: 86fab110 ("Kconfig: Enable FIT_SIGNATURE if ARM64")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Hardkernel ODROID-M1 is a single board computer with a RK3568B2 SoC,
a slightly modified version of the RK3568 SoC.
Features tested on a ODROID-M1 8GB v1.0 2022-06-13:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe/AHCI
- SATA port
- USB host
Device tree is imported from linux v6.4.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The standard boot path expects the kernel_comp_addr_r and kernel_comp_size
variables for booting compressed kernel images. Define them using the previous
kernel_addr_c value (likely initially meant for this purpose) and usual size.
This was tested on the PX30 EVB to successfully boot compressed Linux kernel
images.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add dev_read_addr_size_index_ptr function with the same functionality as
dev_read_addr_size_index, but instead a return pointer is given.
Use map_sysmem() function as cast for the return.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This adds a new USBDP combo PHY with Samsung IP block driver.
The PHY is a combo between USB 3.0 and DisplayPort alt mode.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
[eugen.hristev@collabora.com: ported to 2023.07, clean-up]
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The EFI doesn't allow removal of handles, unless all hosted protocols
are cleanly removed. Our efi_delete_handle() is a bit intrusive.
Although it does try to delete protocols before removing a handle,
it doesn't care if that fails. Instead it only returns an error if the
handle is invalid. On top of that none of the callers of that function
check the return code.
So let's rewrite this in a way that fits the EFI spec better. Instead
of forcing the handle removal, gracefully uninstall all the handle
protocols. According to the EFI spec when the last protocol is removed
the handle will be deleted. Also switch all the callers and check the
return code. Some callers can't do anything useful apart from reporting
an error. The disk related functions on the other hand, can prevent a
medium that is being used by EFI from removal.
The only function that doesn't check the result is efi_delete_image().
But that function needs a bigger rework anyway, so we can clean it up in
the future
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The structure icmp6_ra_prefix_info needs to be packed because it is read
from a network stream.
Signed-off-by: Ehsan Mohandesi <emohandesi@linux.microsoft.com>
Reviewed-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Since commit 56670d6fb8 ("disk: part: use common api to lookup part
driver") part_get_info_by_name_type() ignores the part_type parameter
used to restrict the partition table type.
omap_mmc_get_part_size() and part_get_info_by_name() are the only
consumers.
omap_mmc_get_part_size() calls with part_type = PART_TYPE_EFI because at
the time of implementation a speed up could be gained by passing the
partition table type. After 5 years experience without this restriction
it looks safe to keep it that way.
part_get_info_by_name() uses PART_TYPE_ALL.
Move the logic of part_get_info_by_name_type() to part_get_info_by_name()
and replace the function in omap_mmc_get_part_size().
Fixes: 56670d6fb8 ("disk: part: use common api to lookup part driver")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit 62649165cb ("lib: sparse: Make CHUNK_TYPE_RAW buffer aligned")
fixed cache alignment for systems with a D-CACHE.
However it introduced some performance regressions [1] on system
flashing huge images, such as Android.
On AM62x SK EVM, we also observe such performance penalty:
Sending sparse 'super' 1/2 (768793 KB) OKAY [ 23.954s]
Writing 'super' OKAY [ 75.926s]
Sending sparse 'super' 2/2 (629819 KB) OKAY [ 19.641s]
Writing 'super' OKAY [ 62.849s]
Finished. Total time: 182.474s
The reason for this is that we use an arbitrary small buffer
(info->blksz * 100) for transferring.
Fix it by using a bigger buffer (info->blksz * FASTBOOT_MAX_BLK_WRITE)
as suggested in the original's patch review [2].
With this patch, performance impact is mitigated:
Sending sparse 'super' 1/2 (768793 KB) OKAY [ 23.912s]
Writing 'super' OKAY [ 15.780s]
Sending sparse 'super' 2/2 (629819 KB) OKAY [ 19.581s]
Writing 'super' OKAY [ 17.192s]
Finished. Total time: 76.569s
[1] https://lore.kernel.org/r/20221118121323.4009193-1-gary.bisson@boundarydevices.com
[2] https://lore.kernel.org/r/all/43e4c17c-4483-ec8e-f843-9b4c5569bd18@seco.com/
Fixes: 62649165cb ("lib: sparse: Make CHUNK_TYPE_RAW buffer aligned")
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
This reverts commit d927d1a808, reversing
changes made to c07ad9520c.
These changes do not pass CI currently.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add MM communication support using FF-A transport
This feature allows accessing MM partitions services through
EFI MM communication protocol. MM partitions such as StandAlonneMM
or smm-gateway secure partitions which reside in secure world.
An MM shared buffer and a door bell event are used to exchange
the data.
The data is used by EFI services such as GetVariable()/SetVariable()
and copied from the communication buffer to the MM shared buffer.
The secure partition is notified about availability of data in the
MM shared buffer by an FF-A message (door bell).
On such event, MM SP can read the data and updates the MM shared
buffer with the response data.
The response data is copied back to the communication buffer and
consumed by the EFI subsystem.
MM communication protocol supports FF-A 64-bit direct messaging.
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Tested-by: Gowtham Suresh Kumar <gowtham.sureshkumar@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Emulate Secure World's FF-A ABIs and allow testing U-Boot FF-A support
Features of the sandbox FF-A support:
- Introduce an FF-A emulator
- Introduce an FF-A device driver for FF-A comms with emulated Secure World
- Provides test methods allowing to read the status of the inspected ABIs
The sandbox FF-A emulator supports only 64-bit direct messaging.
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add Arm FF-A support implementing Arm Firmware Framework for Armv8-A v1.0
The Firmware Framework for Arm A-profile processors (FF-A v1.0) [1]
describes interfaces (ABIs) that standardize communication
between the Secure World and Normal World leveraging TrustZone
technology.
This driver uses 64-bit registers as per SMCCCv1.2 spec and comes
on top of the SMCCC layer. The driver provides the FF-A ABIs needed for
querying the FF-A framework from the secure world.
The driver uses SMC32 calling convention which means using the first
32-bit data of the Xn registers.
All supported ABIs come with their 32-bit version except FFA_RXTX_MAP
which has 64-bit version supported.
Both 32-bit and 64-bit direct messaging are supported which allows both
32-bit and 64-bit clients to use the FF-A bus.
FF-A is a discoverable bus and similar to architecture features.
FF-A bus is discovered using ARM_SMCCC_FEATURES mechanism performed
by the PSCI driver.
Clients are able to probe then use the FF-A bus by calling the DM class
searching APIs (e.g: uclass_first_device).
The Secure World is considered as one entity to communicate with
using the FF-A bus. FF-A communication is handled by one device and
one instance (the bus). This FF-A driver takes care of all the
interactions between Normal world and Secure World.
The driver exports its operations to be used by upper layers.
Exported operations:
- ffa_partition_info_get
- ffa_sync_send_receive
- ffa_rxtx_unmap
Generic FF-A methods are implemented in the Uclass (arm-ffa-uclass.c).
Arm specific methods are implemented in the Arm driver (arm-ffa.c).
For more details please refer to the driver documentation [2].
[1]: https://developer.arm.com/documentation/den0077/latest/
[2]: doc/arch/arm64.ffa.rst
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
convert UUID string to little endian binary data
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
add support for x0-x17 registers used by the SMC calls
In SMCCC v1.2 [1] arguments are passed in registers x1-x17.
Results are returned in x0-x17.
This work is inspired from the following kernel commit:
arm64: smccc: Add support for SMCCCv1.2 extended input/output registers
[1]: https://documentation-service.arm.com/static/5f8edaeff86e16515cdbe4c6?token=
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
- Actually merge the assorted K3 platform improvements that were
supposed to be in commit 247aa5a191 ("Merge branch
'2023-07-21-assorted-TI-platform-updates'")
The clock id needs to be changed to be consistent with Linux.
Signed-off-by: Xingyu Wu <xingyu.wu@starfivetech.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Reviewed-by: Torsten Duwe <duwe@suse.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Since K3 devices are moving towards distroboot, remove duplicates and
add it in common file to import from.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
[trini: Add am65x_evm to this patch]
Signed-off-by: Tom Rini <trini@konsulko.com>
Since get_fdt_mmc is common, factor it out into mmc.env and remove
it from each platform env file along with changing the directory path to
reflect the standards. Use it in mmcloados but keep loadfdt
defined in case it is still used by some external uEnv.txt script.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
In Linux the ARM64 DTSs are stored in vendor directories to help organize
the files and prevent naming collisions. The deployed DTBs will mirror
this and so the vendor prefix should be added to the variable used to
locate these files.
Suggested-by: Ryan Eatmon <reatmon@ti.com>
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
Add method to reserve video framebuffer information using blob,
received from previous stage.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Non-HS boards can use FIT images so include the env var commands
for these unconditionally.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
axi_emac:
- Change return value if RX packet is not ready
cadence_qspi:
- Enable flash reset for Versal NET
dt:
- Various DT syncups with Linux kernel
- SOM - reserved pmufw memory location
fpga:
- Add load event
mtd:
- Add missing dependency for FLASH_CFI_MTD
spi/nand:
- Minor cleanup in Xilinx drivers
versal-net:
- Prioritize boot device in boot_targets
- Wire mini ospi/qspi/emmc configurations
watchdog:
- Use new versal-wwdt property
xilinx:
- fix sparse warnings in various places ps7_init*
- add missing headers
- consolidate code around zynqmp_mmio_read/write
- switch to amd.com email
zynqmp_clk:
- Add handling for gem rx/tsu clocks
zynq_gem:
- Configure mdio clock at run time
zynq:
- Enable fdt overlay support
zynq_sdhci:
- Call dll reset only for ZynqMP SOCs
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZLqHzgAKCRDKSWXLKUoM
IcdEAKCSgy0lMxb1c0adCjpkQR9x63oKbQCdGiioU+W+0moznHdI7+W2UptNt3w=
=Uzn8
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2023.10-rc1-v2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2023.10-rc1 v2
axi_emac:
- Change return value if RX packet is not ready
cadence_qspi:
- Enable flash reset for Versal NET
dt:
- Various DT syncups with Linux kernel
- SOM - reserved pmufw memory location
fpga:
- Add load event
mtd:
- Add missing dependency for FLASH_CFI_MTD
spi/nand:
- Minor cleanup in Xilinx drivers
versal-net:
- Prioritize boot device in boot_targets
- Wire mini ospi/qspi/emmc configurations
watchdog:
- Use new versal-wwdt property
xilinx:
- fix sparse warnings in various places ps7_init*
- add missing headers
- consolidate code around zynqmp_mmio_read/write
- switch to amd.com email
zynqmp_clk:
- Add handling for gem rx/tsu clocks
zynq_gem:
- Configure mdio clock at run time
zynq:
- Enable fdt overlay support
zynq_sdhci:
- Call dll reset only for ZynqMP SOCs
This enables implementing custom logic after a bitstream was loaded
into the fpga.
Signed-off-by: Christian Taedcke <christian.taedcke@weidmueller.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Link: https://lore.kernel.org/r/20230720072724.11516-1-christian.taedcke-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Currently xspi0 is used for all spi boot modes, it means it will use "sf
probe 0 0 0" for all spi's irrespective of which node it is wired.
Get boot sequence from dev_seq() and update boot command for xspi
dynamically.
As a result bootcmd for spi is updated as below when two instances of spi
are present in DT node.
bootcmd_xspi0=devnum_xspi=0; run xspi_boot
bootcmd_xspi1=devnum_xspi=1; run xspi_boot
xspi_boot=sf probe $devnum_xspi:0 0 0 && sf read $scriptaddr
$script_offset_f $script_size_f && echo XSPI: Trying to boot script at
${scriptaddr} && source ${scriptaddr}; echo XSPI: SCRIPT FAILED:
continuing...;
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230614093058.30438-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The behaviour of dev_read_addr_size() is surprising as it does not
handle #address-cells and #size-cells but instead hardcodes the values
based on sizeof(fdt_addr_t).
This is different from dev_read_addr_size_index() and
dev_read_addr_size_name() both of which do read the cell sizes from the
device tree.
Since dev_read_addr_size() is only used by a single driver and this
driver is broken when CONFIG_FDT_64BIT does not match the address size
in the device tree, fix the function to behave like all of the other
similarly named functions. Drop the property name argument as the only
caller passes "reg" and this is the expected property name matching the
other similarly named functions.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # chromebook_jerry
Tested-by: Simon Glass <sjg@chromium.org> # chromebook_bob
With gcc-13.1 we get a warning about enum vs int here, so correct the
declaration to match the implementation.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On devices with multiple USB mass storage devices errors like
Path /../USB(0x0,0x0)/USB(0x1,0x0)/Ctrl(0x0)
already installed.
are seen. This is due to creating non-unique device paths. To uniquely
identify devices we must provide path nodes for all devices on the path
from the root device.
Add support for generating device path nodes for all uclasses.
Reported-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
A previous patch is removing the last consumer of efi_remove_protocol().
Switch that to static and treat it as an internal API in order to force
users install and remove protocols with the appropriate EFI functions.
It's worth noting that we still have files using efi_add_protocol(). We
should convert all these to efi_install_multiple_protocol_interfaces()
and treat efi_add_protocol() in a similar manner
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
If a tuning command times out, the card could still be processing it,
which will cause problems for recovery. The eMMC specification section
6.6 Data transfer mode (cont’d) claims that CMD12 can be used to stop
CMD21:
"
The relationship between the various data transfer modes is summarized (see Figure 27):
- All data read commands can be aborted any time by the stop command (CMD12).
The data transfer will terminate and the Device will return to the Transfer State.
The read commands are: ... send tuning block (CMD21) ....
"
Add a function that does that.
Based on Linux commit [1] and [2].
[1] e711f0309109 ("mmc: mmc: Introduce mmc_abort_tuning()")
[2] 21adc2e45f4e ("mmc: Improve function name when aborting a tuning
cmd")
Reviewed-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Update commit message, quote relevant part of the specification.
Rename to mmc_send_stop_transmission().
Remove tuning opcode check, this is controller driver specific.
Deduplicate part of mmc_read_blocks() using this function.]
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Adds part_driver_get_type() API which can be used to force a specific
driver to be used when getting partition information instead of relying
on auto detection.
Signed-off-by: Joshua Watt <JPEWhacker@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is is sometimes desired to be able to skip decrementing the number of
tries remaining in an Android A/B boot, and instead just check which
slot will be tried later. This can commonly be be the case for platforms
that want to A/B u-boot itself, but are required to boot from a FAT MBR
partition. In these cases, u-boot must do an early check that the MBR
points to the correct A/B boot partition, and if not rewrite the MBR to
point to the correct one and reboot. Decrementing the try count in this
case is not desired because it means that each u-boot might constantly
ping-pong overwriting the MBR and rebooting until all the retries are
used up.
Signed-off-by: Joshua Watt <JPEWhacker@gmail.com>
Fix it to 'boot' in the header, as it is in the source file.
Signed-off-by: Julien Delbergue <j.delbergue.foss@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When video is set up in SPL, U-Boot proper needs to use the correct
parameters so it can write to the display.
Put these in a bloblist so they are available to U-Boot proper.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is useful to see the base of the malloc region. This is visible when
debugging but not in normal usage.
Add it to the global data so that it can be shown.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Nikhil M Jain <n-jain1@ti.com>
Some devices have multiple partition types available on the same media.
It is sometimes useful to see these to check that everything is working
correctly.
Provide a way to manually set the partition-table type, avoiding the
auto-detection process.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is always zero in the source tree, so drop it.
While we are here, add a comment to _X86EMU_env since the symbol is
actually defined twice, which can cause confusion when building.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some Linux parameters can be set automatically by U-Boot, if it knows the
device being used. For example, since U-Boot knows the serial console
being used, it can add parameters for earlycon and console.
Add support for this.
Note that this is an experimental feature and we will see how useful it
turns out to be. It is very handy for ChromeOS, since otherwise it is very
difficult to manually determine the UART address or port number,
particularly in a script.
Provide an example of how this is used with ChromeOS.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Drop use of the distro boot script and use standard boot instead.
Moving to a text-based environment would be desirable also, but requires
additional work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a bootflow command to update the command line more easily. This allows
changing a particular parameter rather than editing a very long strings.
It is also easier to handle with scripting.
The new 'bootflow cmdline' command allows getting and setting single
parameters.
Fix up the example output while we are here, since there are a few new
items.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Linux command line consists of a number of words with optional values.
At present U-Boot allows this to be changed using the bootargs environment
variable.
But this is quite painful, since the command line can be very long.
Add a function which can adjust a single field in the command line, so
that it is easier to make changes before booting.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
On x86 boards Linux uses a block of binary data to provide information
about the command line, memory map, etc. Provide a way to store this in
the bootflow so it can be passed on to the OS.
No attempt is made to generalise the code, since other archs don't need
this information. The field is present always, though, to avoid needing
accessors or #ifdefs when building code on other archs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The "bootargs" environment variable is used to set the command-line
arguments to pass to the OS. Use this same mechanism with bootstd as well.
When the variable is updated, it is written to the current bootflow. When
the current bootflow is updated, the environment variable is updated too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some operating systems have a command line which can be adjusted before
booting. Store this in the bootflow so it can be controlled within
U-Boot.
Fix up the example output while we are here, since there are a few new
items.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It seems better to call this a 'bootdev' since this is name used in the
documentation. The older 'Bootdevice' name is no-longer used and may cause
confusion with the 'bootdevice' environment variable.
Update throughout to use bootdev.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Rename and move bootorder and bootoption apis from cmd to lib
for re-use between eficonfig and bootmgr
Fix 'unexpected indentation' when 'make htmldocs' after functions
are moved
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add a new 'cedit' command which allows editing configuration using an
expo. The configuration items appear as menus on the display.
This is extremely basic, only supporting menus and not providing any way
to load or save the configuration.
Signed-off-by: Simon Glass <sjg@chromium.org>
The only way to create an expo at present is by calling the functions to
create each object. It is useful to have more data-driven approach, where
the objects can be specified in a suitable file format and created from
that. This makes testing easier as well.
Add support for describing an expo in a devicetree node. This allows more
complex tests to be set up, as well as providing an easier format for
users. It also provides a better basis for the upcoming configuration
editor.
Signed-off-by: Simon Glass <sjg@chromium.org>
In 'popup' mode, the expo allows moving around the objects in a scene.
When 'enter' is pressed on a menu, it opens and the user can move around
the items in the menu.
Implement this using keypress handles and actions.
Signed-off-by: Simon Glass <sjg@chromium.org>
When a popup menu is closed it shows only the selected item. When it is
open it shows a background and all items, with a highlight that can be
moved between the items.
Add the drawing logic for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we only support a single menu, so all that can be pointed to
is the current menu item. Rename this action so that we can also add
an action for pointing to an object. This will allow cycling through
the objects in a scene.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present only a single menu is supported. All items are shown and a
pointer object points to the current item.
Add support for multiple menus, one of which is highlighted, indicated
by the highlight_id property in the scene.
The highlighted menu item has a SCENEOF_POINT flag, indicating that it
is currently pointed to.
The popup menu is normally closed, in which case it shows only the
current menu item. When it is opened, it shows all items, allowing the
user to select one.
Rather than requiring the menu item to have a description, require it to
have a label. Use the label (only) for the popup menu.
With this, most of the drawing and layout logic is complete.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is a pain to manually set the fonts of all objects to be consistent.
Some spacing settings are also better set globally than by manually
positioning each object.
Add a 'theme' to the expo, to hold this information. For now it includes
only the font size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide a way to set the full dimensions of objects, i.e. including the
width and height.
For menus, calculate the bounding box of all objects in the menu. Set all
labels to be the same size, so that highlighting works correct, once
implemented.
Signed-off-by: Simon Glass <sjg@chromium.org>
We currently have just a 'hide' property for each object. In preparation
for adding more properties, convert the struct to use a flags value,
instead of individual booleans. This is more extensible.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present objects only have a position so it is not possible to determine
the amount of space they take up on the display.
Add width and height properties, using a struct to keep all the dimensions
together.
For now this is not used. Future work will set up these new properties.
Signed-off-by: Simon Glass <sjg@chromium.org>
