=> usb start
starting USB...
Bus usb@fd000000: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus usb@fd800000: USB EHCI 1.00
scanning bus usb@fd000000 for devices... cannot reset port 1!?
2 USB Device(s) found
scanning bus usb@fd800000 for devices... 4 USB Device(s) found
scanning usb for storage devices... 2 Storage Device(s) found
=> usb tree
USB device tree:
1 Hub (5 Gb/s, 0mA)
| U-Boot XHCI Host Controller
|
+-2 Mass Storage (5 Gb/s, 224mA)
SanDisk Dual Drive 04019c9b2e1a58f24ee318c3c123aa5
1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
+-2 Hub (480 Mb/s, 100mA)
| USB 2.0 Hub
|
+-3 Mass Storage (480 Mb/s, 500mA)
| JetFlash Mass Storage Device 19M7I4ZQFTSC08SU
|
+-4 Human Interface (12 Mb/s, 98mA)
Logitech USB Receiver
Co-developed-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Radxa Compute Module 3(CM3) IO board an application board from Radxa
and is compatible with Raspberry Pi CM4 IO form factor.
Radxa CM3 needs to mount on top of this IO board in order to create
complete Radxa CM3 IO board platform.
Add support for Radxa CM3 IO Board defconfig and -u-boot.dtsi
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add Radxa ROCK 3 Model A support. sync rk3308-rock-pi-s.dts from
Linux 6.2.0-rc7.
ROCK Pi S is RK3308 based SBC from radxa.com. ROCK Pi S has a,
- 256MB/512MB DDR3 RAM
- SD, NAND flash (optional on board 1/2/4/8Gb)
- 100MB ethernet, PoE (optional)
- Onboard 802.11 b/g/n wifi + Bluetooth 4.0 Module
- USB2.0 Type-A HOST x1
- USB3.0 Type-C OTG x1
- 26-pin expansion header
- USB Type-C DC 5V Power Supply
Linux commit commit for the same,
<2e04c25b1320> ("arm64: dts: rockchip: add ROCK Pi S DTS support")
Signed-off-by: Akash Gajjar <gajjar04akash@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add Radxa ROCK 3 Model A support. sync rk3568-rock-3a.dts from Linux 6.2.0-rc7
Board Specifications
- Rockchip RK3568
- 2/4/8GB LPDDR4 3200MT/s
- eMMC socket, SD card slot
- GbE LAN
- PCIe 3.0/2.0
- M.2 Connector
- 3.5mm Audio jack with mic
- HDMI 2.0, MIPI DSI/CSI
- USB 3.0 Host/OTG, USB 2.0 Host
- 40-pin GPIO expansion ports
- USB Type C PD 2.0, 9V/2A, 12V/2A, 15V/2A, 20V/2A
Refer Linux commit <22a442e6586c>
("arm64: dts: rockchip: add basic dts for the radxa rock3 model a")
Signed-off-by: Akash Gajjar <gajjar04akash@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
An external TPL binary is now expected to be provided using ROCKCHIP_TPL
when building RK3568 targets.
This reverts commit 31500e7bcf.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
CONFIG_RAM_PX30_DDR4 got renamed to CONFIG_RAM_ROCKCHIP_DDR4 in commit
26f92be07e ("ram: rockchip: Add common ddr type configs"). Since both
patchsets were merged unbeknownst to the other, the conflict wasn't
detected while testing each patchset individually and could only be
observed after a merge to master branch.
Fixes: c925be73a0 ("rockchip: add support for PX30 Ringneck SoM on Haikou Devkit")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Provide human-readable manufacturer and product names for the
FriendlyELEC NanoPi R4S.
Enable CONFIG_SYSINFO and CONFIG_SYSINFO_SMBIOS by default.
Signed-off-by: Christian Kohlschütter <christian@kohlschutter.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
All Nvidia boards use the same manufacturer, vendor ID and product ID
for the gadgets. Make them the defaults to remove some boilerplate from
the defconfigs.
Inspired by commit e02687bda9 ("sunxi: provide default USB gadget
setup") which did the same for Allwinner boards.
Tested-by: Thierry Reding <treding@nvidia.com> # T30 and T124
Signed-off-by: Maxim Schwalm <maxim.schwalm@gmail.com>
Signed-off-by: Tom <twarren@nvidia.com>
Replacing with dwc3-generic, no need USB_XHCI_DWC3 anymore.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This file was missed during the conversion process. Add the symbol to
defconfig.
Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adjust the initial stack pointer address to 0x10000000(256M)
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The current ae350-related defconfigs could also
support newer Andes CPU IP, so modify the names of CPU
from ax25 to andesv5, and board name from ax25-ae350 to ae350.
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Display information about CPU and board during start up.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Loading an image via TFTP is often interrupted when retrying more than
10 times, increase the number of retries so that it does not simply stop
the transfer.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
To reduce the code size, CONFIG_V5L2_CACHE was disabled since commit:
ca06444aac
Turing on does not significantly increase the size of u-boot-spl.bin,
so we enable it by default to improve performance.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Synology DS116 is a NAS based on Marvell Armada 385 SoC.
Board Specification:
- Marvel MV88F6820 Dual Core at 1.8GHz
- 1 GiB DDR3 RAM
- 8MB Macronix mx25l6405d SPI flash
- I2C
- 2x USB 3.0
- 1x GBE LAN port (PHY: Marvell 88E1510)
- 1x SATA (6 Gbps)
- 3x LED
- PIC16F1829 (connected to uart1)
- GPIO fan
- serial console
Note that this patch depends on the add-support for Thecus N2350 patch:
https://patchwork.ozlabs.org/project/uboot/patch/20230201231306.7010-1-mibodhi@gmail.com/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Sheevaplug board has 512K CONFIG_BOARD_SIZE_LIMIT. Recently, DM_SERIAL has
pushed the image size a few hundred bytes over that limit. So explicitly
deselect some configs that are unrelated to this board
(and gain back a bit over 2K).
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
- A fix for a long standing bug that has been exposed by commit
50128aeb0f ("cyclic: get rid of cyclic_init()") preventing 8xx boards
from booting since u-boot 2023.01
- A GPIO driver for powerpc 8xx chip
- Fixup for powerpc 8xx SPI driver
- A new powerpc 8xx board
- The two devices having that board.
This adds a new board from CS GROUP. The board is called
MCR3000_2G, and has a CPU board called CMPC885.
That CPU board is shared with another equipment that will
be added in a later patch.
That board stores Ethernet MAC addresses in an EEPROM which
is accessed using SPI bus.
This patch was originally written by Charles Frey who's
email address is not valid anymore as he left the company.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: FRANJOU Stephane <stephane.franjou@csgroup.eu>
Both U-boot and Linux kernel have grown over the last releases
and don't fit anymore in the 2M EPROM of the board.
So, rework the setup to allow storing the Linux kernel image
on the UBIFS NAND Flash.
Also add support to FIT images as this is what the Linux kernel
look like nowadays.
Also increase CFG_SYS_BOOTMAPSZ to 32Mbytes and define
CONFIG_SYS_BOOTM_LEN with the same value, otherwise it defaults
to 8M which is not sufficient anymore with nowadays Linux kernels.
And set the netmask to 255.255.255.0 as a class C address is used.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: FRANJOU Stephane <stephane.franjou@csgroup.eu>
as Tom suggested get rid of CFG_EXTRA_ENV_SETTINGS and
enable CONFIG_ENV_SOURCE_FILE and use text file
board/socrates/socrates.env
which contains the default environment. While at it,
cleanup the default Environment.
Signed-off-by: Heiko Schocher <hs@denx.de>
Suggested-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
As explained by Philippe Schenker, I was misinterpreting what happened
in the case where we do not set LMB_USE_MAX_REGIONS and so had
re-introduced the problem I was attempting to more widely resolve.
This reverts commit 007ae5d108.
Reported-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Drop use of the distro scripts and use standard boot instead.
Enable BOOTDEV_FULL just for convenience, although this does add quite a
bit to the size.
Signed-off-by: Simon Glass <sjg@chromium.org>
We need to support a basic set of filesystems for booting to work in most
cases. Add these in via a new option, letting the board disable them
individually (for space reasons) if desired.
This enables the filesystem commands as well as the actual functionality,
even though bootstd is quite happy to use ext4 without the ext4 command.
Further work would be needed to disintangle this and reduce code size.
Add several other options as well, providing sensible defaults.
We cannot enable this by default, since it expands the size of many
boards quite a lot.
Signed-off-by: Simon Glass <sjg@chromium.org>
am335x_evm_defconfig is used for BeagleBone Black, popular single board
computer with wide extension support. Enable CONFIG_CMD_EXTENSION by default
since extension detection is already implemented for am335x.
Also run make savedefconfig for am335x_evm_defconfig
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
setup MTD partitioning through mtdparts variable
and set it to:
mtdparts=fe0000000.nor:13312k(system1),13312k(system2),5120k(data),128k(env),128k(env-red),768k(u-boot)
and pass this to linux per kernel commandline.
Signed-off-by: Heiko Schocher <hs@denx.de>
convert socrates board to use MPC85XX_HAVE_RESET_VECTOR and
disable CONFIG_OF_BOARD and use common u-boot.dtsi for
creating u-boot-dtb.bin.
Signed-off-by: Heiko Schocher <hs@denx.de>
current mainline does not work on socrates board. To
get it back up working, there are some updates needed
in socrates_defconfig.
Signed-off-by: Heiko Schocher <hs@denx.de>
Fixes: 94633c36f9 ("net: Make DM_ETH be selected by NETDEVICE")
Fixes: 2f8a6db5d8 ("Finish conversion of CONFIG_SYS_CLK_FREQ to Kconfig")
The LMB code allows for picking a hard limit on the number of regions it
can know of, or to dynamically allocate these regions. The reason for
this choice is to allow for the compiler to perform a size optimization
in the common case. This optimization however, is very small, ranging
from 196 bytes to 15 bytes saved, or in some cases, being larger. Now
that we also have more regions covered by LMB (in order to protect
various parts of our self at run time), the default of 8 is also much
easier to hit and leads to non-obvious error messages (which imply that
an area is protected, not that we're out of areas to add to the list).
Switch to the dynamic use as the default.
Signed-off-by: Tom Rini <trini@konsulko.com>
Convert to DM_SERIAL and drop the iomux board file
level init as it's handled as part of the DM serial
layer instead.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This moves over the PMIC power init to DM and the associated i2c and
regulator bits.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add MV88E61XX DSA support:
- update dt to provide internal MDIO bus and port handles.
U-Boot requires a more restrictive subset of the dt bindings
required by Linux for the sake of simplifying code
- update defconfig to remove old driver and enable new one
- replace mv88e61xx_hw_reset weak override with board_phy_config support
for register configuration that is outside the scope of the DSA driver
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Enable I2C support on D3 Draak.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car device trees with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
The following script has been used for the synchronization:
$ for i in $(cd arch/arm/dts/ ; ls -1 r8a* | grep -v 'u-boot.dts' ; sed -n '/#include/ s@.*"\(.*\)"@\1@p' $(ls -1 r8a* | grep -v 'u-boot.dts')) ; do
if [ -e /linux-2.6/arch/arm64/boot/dts/renesas/$i ] ; then
cp /linux-2.6/arch/arm64/boot/dts/renesas/$i arch/arm/dts/ ;
elif [ -e /linux-2.6/arch/arm/boot/dts/$i ] ; then
cp /linux-2.6/arch/arm/boot/dts/$i arch/arm/dts/
else
echo "NOT FOUND: $i"
fi
done
$ git add $( ( cd arch/arm/dts/ ; ls -1 r8a* | grep -v 'u-boot.dts' ; sed -n '/#include/ s@.*"\(.*\)"@\1@p' $(ls -1 r8a* | grep -v 'u-boot.dts')) | tr " " "\n" | sed 's@^@arch/arm/dts/@g' )
Move the include/dt-bindings/{clk,clock}/versaclock.h header used by
the renesas boards to match Linux 6.1.y as well.
Keep arch/arm/dts/r8a774c0-u-boot.dtsi sdhi3 node as it is now used
by the arch/arm/dts/r8a774c0-cat874.dts board.
Pick s@spi-flash@flash@ change in arch/arm/dts/r8a779a0-falcon-u-boot.dts
from "ARM: dts: Synchronize R-Car V3U DTs with Linux 5.18.3" .
Adjust R8A77990 Ebisu CONFIG_SYS_MMC_ENV_DEV from 2 to 0 to reflect
the card enumeration in ebisu.dtsi /aliases DT node .
Adjust R8A7795 and R8A7796 ULCB CONFIG_SYS_MMC_ENV_DEV from 1 to 0 to
reflect the card enumeration in ulcb.dtsi /aliases DT node .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com> # r8a779a0-falcon-u-boot.dts
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> # r8a779a0-falcon-u-boot.dts
The imx8mn-beacon SOM has a QSPI part on it connected to the
FlexSPI controller. Add a defconfig option which supports
booting from the QSPI NOR flash instead of sd/mmc.
Signed-off-by: Adam Ford <aford173@gmail.com>
The introduction of CONFIG_FSL_QSPI_AHB_FULL_MAP as default in:
def88bce09 ("spi: fsl_qspi: Support to use full AHB space on i.MX")
broke the SPI NAND read access on the Kontron SL i.MX6UL/ULL boards.
Reading data from the flash returns garbage instead of the actual
content. Fix this for now by disabling the introduced option.
In the long run this should be fixed globally.
Fixes: def88bce09 ("spi: fsl_qspi: Support to use full AHB space on i.MX")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add the board support for the i.MX8MM Cloos PHG board.
This board uses a imx8mm-tqma8mqml SoM from TQ-Group.
imx8mm-phg.dts and imx8mm-tqma8mqml.dtsi are taken
directly from Linux 6.2-rc3.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
The i.MX 8M Mini SoC does incorporate an additional M-Core. To be able
to load it with a firmware, enable bootaux command as other Toradex
modules also have it enabled to be consistent.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Set i.MX auxiliary core memory base and size.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Update the distro config env memory layout for the Apalis iMX8 aka
QuadMax:
- kernel_comp_addr_r=0xf0000000 temporary area for uncompressing (ie FIT
images or Image.gz booted using booti)
- kernel_comp_size=0x08000000
- loadaddr=0x95400000 avoiding any reserved areas located before that
- fdt_addr_r = loadaddr + 128MB - allows for 128MB kernel
- scriptaddr = fdt_addr_r + 512KB - allows for 512KB fdt
- ramdisk_addr_r = scriptaddr + 512KB - allows for 512KB script
Basic idea of memory layout taken from commit fd5c7173ad
("imx8m{m,n}_venice: update env memory layout"). However, moved past
any reserved areas to avoid any kind of conflicts.
Note that for our regular BSP Layers and Reference Images for Yocto
Project an updated distro boot script is required (see
meta-toradex-bsp-common/recipes-bsp/u-boot/u-boot-distro-boot).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
There is no "apply" command enabled for "fdt".
Enable "apply" command to allow overlays to be applied.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Set the boot delay to one second.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This provides correct system prompt for U-Boot console.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Implement PCB version and SoC variant handling which automatically loads
the correct device tree for the Linux kernel.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
ODROID-N2L is a variant SBC in small form factor and some peripherals
are removed from ODROID-N2PLUS based on S922X SoC.
- On-board ethernet is removed
- On-board RTC is removed
- USB 3.0 hub is removed, so one USB 2.0 and one USB 3.0 host ports
are available
- Huge heatsink is replaced with 40x40mm heatsink, 5V active heatsink
is recommended or a tall passive sink is optional
- 3.5mm earjack is removed
- IR remote receiver is removed
- MIPI DSI port is added
It doesn't use the odroid-n2 board support since ADC revision
collides with Odroid-N2+ and since it doesn't have on-board ethernet
no need to load the MAC address from eFuses.
Link: https://lore.kernel.org/r/20230126-u-boot-odroid-n2l-v1-2-c60f695e0f6c@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Some Apple Silicon machines have a PCIe XHCI controller in additon
to the DWC3 controllers integrated on the SoC. On the Mac mini
the Type-A ports are handled by this PCIe controller. Enabling
it allows the use of these ports in U-Boot.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
J721S2 EVM used to store env on eMMC, since EVM and SK uses same
defconfig and there is no eMMC on SK, we need to keep env in an
interface which available on both EVM and SK. So, save env in FAT
partition of MMC SD Card.
Enable defconfigs relevant for storing env on FAT partition of MMC.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Enable configs for building multiple dtbs into a single fit image
and load the right dtb for next stage. Add k3-am68-sk-base-board
dtb along with evm dtb inside DTB FIT image. This helps to use same
defconfig for both EVM and SK
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Enable configs for building multiple dtbs into a single fit image
and load the right dtb for next stage. This will help to use same
defconfig for both EVM and SK.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
makefile:
- Add multi_dtb_fit dependency
clk:
- Handle error cases
microblaze:
- Disable falcon mode and cleanup code around
xilinx:
- Enable regular expression matching in board_fit_config_name_match()
- Fix FRU handling for 0xC1 format
- Fix Xilinx legacy format eeprom parsing
zynqmp:
- Some DT updates/cleanups
- Fix IDcode for xck24
- Remove empty mini config files
- Add support for k24
versal:
- Remove empty mini config files
versal_net:
- Setup timer when runs in EL3
- Build u-boot.elf for mini configurations
zynq-gem:
- Add support for new compatible strings
- Remove support for Avnet Ultrazedev SOM
- Handle SGMII with PCS phy
spi:
- Add support for gigadevice parts
misc:
- Remove CONFIG_TARGET_VENUS ifdef
- Add missing headers to remove sparse warnings
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCY9PmzwAKCRDKSWXLKUoM
IYWxAJwNgiXtFT17pBy+1M0JvSWgyvWF3QCfTQG2Krnw0+d65PF5A7UFTDL7SZM=
=cMrc
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2023.04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx chnages for v2023.04-rc1
makefile:
- Add multi_dtb_fit dependency
clk:
- Handle error cases
microblaze:
- Disable falcon mode and cleanup code around
xilinx:
- Enable regular expression matching in board_fit_config_name_match()
- Fix FRU handling for 0xC1 format
- Fix Xilinx legacy format eeprom parsing
zynqmp:
- Some DT updates/cleanups
- Fix IDcode for xck24
- Remove empty mini config files
- Add support for k24
versal:
- Remove empty mini config files
versal_net:
- Setup timer when runs in EL3
- Build u-boot.elf for mini configurations
zynq-gem:
- Add support for new compatible strings
- Remove support for Avnet Ultrazedev SOM
- Handle SGMII with PCS phy
spi:
- Add support for gigadevice parts
misc:
- Remove CONFIG_TARGET_VENUS ifdef
- Add missing headers to remove sparse warnings
U-Boot is composing u-boot.bin from u-boot-nodtb.bin with appended
dts/dt.dtb. It means U-Boot doesn't have DTB inside. When REMAKE_ELF is
enabled make will also create u-boot.elf which is recreated from
u-boot.bin. Below is build output for mini configuration how ELF is
recreated.
cat arch/arm/dts/versal-net-mini.dtb > dts/dt.dtb
cat u-boot-nodtb.bin dts/dt.dtb > u-boot-dtb.bin
cp dts/dt.dtb u-boot.dtb
cp u-boot-dtb.bin u-boot.bin
aarch64-linux-gnu-objcopy -I binary -B aarch64 -O elf64-littleaarch64
u-boot.bin u-boot-elf.o
aarch64-linux-gnu-ld.bfd u-boot-elf.o -o u-boot.elf -EL -T u-boot-elf.lds
--defsym="_start"=0xBBF00000 -Ttext=0xBBF00000
It is useful to have u-boot.elf present because Xilinx XSDB debugger can
load ELF file and user doesn't need to specify loading address for
u-boot.bin.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/ca550c5c4bf908e757a49a83fdfab0e7100de45e.1674121617.git.michal.simek@amd.com
Drop falcon mode configs from microblaze-generic_defconfig, so that a
defconfig build will still boot into u-boot proper.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20230125164157.1638680-3-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
For Kirkwood boards, it is necessary to have early malloc in DRAM area
when Driver Model for Serial is enabled. This patch removes individual
board settings for early malloc in various Kirkwood boards, and uses the
Kirkwood commonly defined settings in arch/arm/mach-kirkwood/Kconfig.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This contains some fixes, and the first bunch of some clean up patches
to get rid of legacy GPIO and PMIC code.
Highlight is the DM AXP PMIC driver, which is required to convert some
drivers over to use DM regulators, and also is required to get rid
of some less optimal PMIC setup code in Trusted Firmware. This isn't
enabled by any defconfig yet, but can be enabled manually and works. For
the full glory some patches are still missing, and this requires more
testing, which would be simpler if the core code is upstream.
The commit eaf6ea6a1d ("Migrate CUSTOM_SYS_INIT_SP_ADDR to Kconfig using
system-constants.h") moved custom init stack pointer address to Kconfig
which ends up in situation that xilinx_versal_mini_qspi.h is not
needed anymore. That's why remove the file and move defconfigs directly to
xilinx_versal_mini.h configuration.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/2d7276ab8d4cb1d245b64287fb59c79325513f22.1674041200.git.michal.simek@amd.com
The commit eaf6ea6a1d ("Migrate CUSTOM_SYS_INIT_SP_ADDR to Kconfig using
system-constants.h") moved custom init stack pointer address to Kconfig
which ends up in situation that xilinx_zynqmp_mini_emmc/qspi.h are not
needed anymore. That's why remove files and move defconfigs directly to
xilinx_zynqmp_mini.h configuration.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/61ae40cf63aabd08adb386c870d3392b0b606fc9.1674040373.git.michal.simek@amd.com
Add a bootdev for SPI flash so that these devices can be used with
standard boot. It only supports loading a script.
Add a special case for the label, since we want to use "spi", not
"spi_flash".
Enable the new bootdev on sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
This bootdev is disabled at present since it messes with the tests. Now
that there is a way to disable networking at runtime, enable the driver.
This allows running tests with it if necessary.
Signed-off-by: Simon Glass <sjg@chromium.org>
For legacy reasons we were defining the card detect GPIO for all sunxi
boards in each board's defconfig.
There is actually no need for a card-detect check in the SPL code (which
consequently has been removed already), and also in U-Boot proper we
have DM code to query the CD GPIO name from the device tree.
That means we don't have any user of that information left, so can
remove the definitions from the defconfigs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
The SoC .dtsi originally submitted for the Allwinner F1C100s had the
wrong compatible string for the watchdog, which broke U-Boot's reset
functionality. To quickly fix this, we disable CONFIG_SYSRESET in
cfcf1952c1 ("sunxi: f1c100s: Drop SYSRESET to enable reset
functionality"), so that U-Boot's hardcoded reset driver could take over.
After this was properly fixed in the devicetree, we reverted that patch
in 92373de041 ("Revert "sunxi: f1c100s: Drop SYSRESET to enable reset
functionality"), however this line sneaked back in with d0ee7f295d
("Convert CONFIG_SYS_PBSIZE to Kconfig"), so during a Kconfig update.
Remove this line (again), to use the proper reset driver.
Fixes: d0ee7f295d ("Convert CONFIG_SYS_PBSIZE to Kconfig")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
This reverts commit 1cfba53ca4.
Since commit 1cfba53ca4 ("config: tools only: add VIDEO to build
bmp_logo") the build of tools-only_defconfig fails:
| /bin/sh: line 1: tools/bmp_logo: No such file or directory
This has been noticed in OpenEmbedded and Debian [1].
Revert it for now.
[1] https://lists.denx.de/pipermail/u-boot/2023-January/504758.html
Signed-off-by: Fabio Estevam <festevam@denx.de>
This adds initial support for the Hardkernel Odroid Go Ultra.
The Odroid Go Ultra is a portable gaming device with the following
characteristics:
- Amlogic S922X SoC
- RK817 & RK818 PMICs
- 2GiB LPDDR4
- On board 16GiB eMMC
- Micro SD Card slot
- 5inch 854×480 MIPI-DSI TFT LCD
- Earphone stereo jack, 0.5Watt 8Ω Mono speaker
- Li-Polymer 3.7V/4000mAh Battery
- USB-A 2.0 Host Connector
- x16 GPIO Input Buttons
- 2x ADC Analog Joysticks
- USB-C Port for USB2 Device and Charging
The following are not yet handled:
- Battery RK818 Gauge and Charging
- 5inch 854×480 MIPI-DSI TFT LCD
Link: https://lore.kernel.org/r/20230119-u-boot-odroid-go-ultra-v1-2-f96bab9db396@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
With CONFIG_DM_USB_GADGET=y, we no longer need any board_usb_*() logic
because:
* the dwc2 driver is DM compatible, and handles its own clock enabling
* the dwc3-meson-gxl glue drivers handles "force mode switching"
Remove all mach-meson gx & axg usb code and enable CONFIG_DM_USB_GADGET.
Note: Only configs having both CONFIG_USB_DWC3_MESON_GXL=y *and*
USB_GADGET_DWC2_OTG=y have been updated.
Thanks for the original work from Mattijs at [1]
[1] https://lore.kernel.org/all/20221024-meson-dm-usb-v1-2-2ab077a503b9@baylibre.com/
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20230117-u-boot-usb-gxl-otg-dm-v1-2-2853f6d75b06@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
patman fix for checkpatch
binman optional entries, improved support for ELF symbols
trace improvements
minor fdt refactoring
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmPIpV4RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZuqwgA0UpYQEX6/MegzHSCIx3AMT4rCF1Ytitr
LS4Cbvj1Q09Rt9jriW7wAV5AobVPwGf2L5SVcnWv2I9+MmypDIXEe8HIrt2fRFu9
bzn/2GOzXczuXqPFa/CWOUwjvCzTb8Sl9NtRszrP5NvOzuN15x00ZUYaXFO7fgsB
zZMzOKxemwjdtLaox+x+VIJ95HMDEkYrWTAqTPg74CNVSjRbbLNqNq0zqkHB8SnH
ubgphtIKYItTeIXcfIa9V4LeQp0ZitkzSfAibX+nIPCMPg9jbG9MrQQ+VvSZDjnM
y8wa8gFj47Ek+gGNFXMHIpO6tBd83uHRgtf2x+zhcovLELYnZ6fDGw==
=1K6m
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-18jan23' of https://source.denx.de/u-boot/custodians/u-boot-dm
convert rockchip to use binman
patman fix for checkpatch
binman optional entries, improved support for ELF symbols
trace improvements
minor fdt refactoring
Enable the sysreset based poweroff command. It invokes PSCI.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This boards uses SPL_FIT so does not need to support loading a raw image.
Drop it to avoid binman trying to insert a symbol which has no value.
Signed-off-by: Simon Glass <sjg@chromium.org>
The fdt_path_offset() function is slow since it must scan the tree.
This substantial overhead now applies to all boards.
The original code may not be ideal but it is fit for purpose and is only
needed on a few boards.
Reverting this reduces time to set up driver model by about 30ms.
Before revert:
Accumulated time:
47,170 dm_r
53,237 dm_spl
572,986 dm_f
Accumulated time:
44,598 dm_r
50,347 dm_spl
549,133 dm_f
This reverts commit 26f981f295.
Signed-off-by: Simon Glass <sjg@chromium.org>
This board is useful for benchmarking overall U-Boot performance. Enable
the bootstage feature so we get a report.
Since this returns to the boot rom before finishing executing
board_init_r() in SPL, add a few bootstage calls so that we can collect
timing from TPL.
For the stash region, use a portion of SRAM, 64KB below the stack top.
This allows the TPL image to be up to nearly 120KB (it is typically about
64KB). SPL normally runs from SDRAM at 0, so can use the same stash
region.
Signed-off-by: Simon Glass <sjg@chromium.org>
To quote the author:
So far standard boot lacks a boot menu, although it is possible to create
a rudimentary one using the existing 'bootmenu' command.
Even then, this text-based menu offer only basic functionality and does
not take full advantage of the displays which are common on many devices.
This series provides a 'bootflow menu' command which allows the user to
select from the available bootflows. An attempt is made to show the name
of the available operating systems, by reading more information into the
bootflow. A logo can be read also, where supported, so that this can be
presented to the user when an option is highlighted.
Full use is made of TrueType fonts, if enabled. For cases where only a
serial console is available, it falls back to a simple text-based menu.
All of this is implementing using a new 'expo' construct, a collection of
scenes (like menu screens) which can be navigated by the user to view
information and select options. This is fairly general and should be able
to cope with a wider array of use cases, with less hacking of the menu
code, such as is currently needed for CMD_BOOTEFI_BOOTMGR.
Of course it would be possible to enhance the existing menu rather than
creating a new setup. Instead it seems better to make the existing menu
use expo, if code space permits. It avoids the event-loop problem and
should be more extensible, given its loosely coupled components and use of
IDs instead of pointers. Further motivation is provided in the
documentation.
For now the CLI keypress-decoding code is split out to be used by the new
menu. The key codes defined by menu.h are reused also.
This is of course just a starting point. Some ideas for future work are
included in the documentation.
With CONFIG_DM_USB_GADGET=y, we no longer need any board_usb_*() logic
because:
* the dwc2 driver is DM compatible, and handles its own clock enabling
* the dwc3-meson-g12a glue drivers handles "force mode switching"
Remove all mach-meson/g12a usb code and enable CONFIG_DM_USB_GADGET.
Note: Only configs having both CONFIG_USB_DWC3_MESON_G12A=y *and*
USB_GADGET_DWC2_OTG=y have been updated.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20221024-meson-dm-usb-v1-2-2ab077a503b9@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add a test which checks that two operating systems can be displayed in a
menu, allowing one to be selected.
Enable a few things on snow so that the unit tests build.
Signed-off-by: Simon Glass <sjg@chromium.org>
An expo is a way of presenting and collecting information from the
user. It consists of a collection of 'scenes' of which only one is
presented at a time. An expo is typically used to show a boot menu
and allow settings to be changed.
One created, the same expo can be automatically presented in graphical
form using a vidconsole, or in text form on a serial console.
Add an initial implementation of the expo itself. Supports for scenes
and objects is provided later.
Signed-off-by: Simon Glass <sjg@chromium.org>
The mmc command is useful for testing mmc disk images in sandbox, so
enable it. We also need to enable legacy images so that we can run tests
which use them.
Disable it for a few avb tests since MMC is not implemented there yet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for starting timer by setting up time stamp generator
registers. This is done only for EL3 i.e. mini U-Boot case.
For other cases, it will be done TF-A.
Add COUNTER_FREQUENCY and IOU_SWITCH_DIVISOR0 to Kconfig so that they
can be tuned as required.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/fcd8b0dc4b45a11f5e753afff42f84738ac813da.1673336645.git.michal.simek@amd.com
The Pinephone Pro is another device by PINE64. It's closely related
to the Pinebook Pro of which this initial support is derived from.
Specification:
- A variant of the Rockchip RK3399
- A 6 inch 720*1440 DSI display
- Front and rear cameras
- Type-C interface with alt mode display (DP 1.2) and PD charging
- 4GB LPDDR4 RAM
- 128GB eMMC
- mSD card slot
- An AP6255 module for 802.11ac WiFi and Bluetooth 5
- Quectel EG25-G 4G/LTE modem
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Neural Compute Module 2(Neu2) IO board is an industrial form factor
IO board from Edgeble AI.
General features:
- microSD slot
- MIPI DSI connector
- 2x USB Host
- 1x USB OTG
- Ethernet
- mini PCIe
- Onboard PoE
- RS485, RS232, CAN
- Micro Phone array
- Speaker
- RTC battery slot
- 40-pin expansion
Neu2 needs to mount on top of this IO board in order to create complete
Edgeble Neural Compute Module 2(Neu2) IO platform.
Add support for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
We have common ddr types in rockchip or in general. So use
the common ddr type names instead of per Rockchip SoC to
avoid confusion.
The respective ddr type names will use on the associated
ddr SoC driver as these drivers are built per SoC at a time.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable efuse support which allows reading of the cpuid#, serial#
and also generates a unique mac address from the board's serial.
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This enables MMC support, which is available
on Condor board, by default.
Signed-off-by: Andrey Dolnikov <andrey.dolnikov@cogentembedded.com>
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Since R-Car Gen3 already enables position independent build, also set
CONFIG_TEXT_BASE=0x0 to finalize the switch. This is possible since
534f0fbd65 ("arm64: Fix relocation of env_addr if POSITION_INDEPENDENT=y")
fixed current env_get_char() crash with CONFIG_TEXT_BASE=0x0 .
This change permits us to start U-Boot from any location in DRAM instead
of specific TEXT_BASE.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Since R-Car Gen3 already enables position independent build, also set
CONFIG_TEXT_BASE=0x0 to finalize the switch. This is possible since
534f0fbd65 ("arm64: Fix relocation of env_addr if POSITION_INDEPENDENT=y")
fixed current env_get_char() crash with CONFIG_TEXT_BASE=0x0 .
This change permits us to start U-Boot from any location in DRAM instead
of specific TEXT_BASE.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Enable LTO (link time optimization) to improve optimization
and reduce code size by cca. 30 kiB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Enable LTO (link time optimization) to improve optimization
and reduce code size by cca. 29 kiB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Enable LTO (link time optimization) to improve optimization
and reduce code size by cca. 34 kiB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Enable LTO (link time optimization) to improve optimization
and reduce code size by cca. 32 kiB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Enable LTO (link time optimization) to improve optimization
and reduce code size by cca. 32 kiB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Enable LTO (link time optimization) to improve optimization
and reduce code size by cca. 31 kiB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Add calibration support for stm32-adc
Linux kernel v6.1 DT synchronization for stm32mp151.dtsi
stm32mp157a-dk1-scmi-u-boot.dtsi update
Add support of OP-TEE and STM32MP13x in bsec driver
ECDSA various fixes for stm32mp
-----BEGIN PGP SIGNATURE-----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=SNID
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20230113' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add driver to manage onboard hub supplies
Add calibration support for stm32-adc
Linux kernel v6.1 DT synchronization for stm32mp151.dtsi
stm32mp157a-dk1-scmi-u-boot.dtsi update
Add support of OP-TEE and STM32MP13x in bsec driver
ECDSA various fixes for stm32mp
This commit adds configs required for using dcp_rng driver in imx6ull
defconfig files.
Signed-off-by: Kshitiz Varshney <kshitiz.varshney@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Activate the command stm32key with CONFIG_CMD_STM32KEY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Activate the command fuse to access on STM32MP13x OTP with
the BSEC driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Activate the USB onboard HUB driver, that is used to enable the HUB supply
on STM32MP15 EVAL, DK1 and DK2 boards.
This avoids marking the 3v3 corresponding regulator as always-on.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
CONFIG_SPL_TARGET should specify additional SPL make target. But
u-boot-with-spl.bin is final U-Boot binary, not SPL binary in some custom
format. Moreover u-boot-with-spl.bin is already set in CONFIG_BUILD_TARGET,
so make will build it by default.
Signed-off-by: Pali Rohár <pali@kernel.org>
It was temporary disabled due to problem with boot.
Issue was fixed in
commit f5ed6c9ccf ("uart: sdm845: Fix debug UART pinmux")
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
We're currently using CONFIG_BOOTCOMMAND to run custom boot scripts to
jump into linux. While this works, let's begin the transition to more
distribution friendly jumps to linux by enabling distro_bootcmd.
Convert the custom bootcmd to a distro_bootcmd
Signed-off-by: Judith Mendez <jm@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Texas Instruments has begun enabling security setting on the SoCs they
produce to instruct ROM and TIFS to begin protecting the Security
Management Subsystem (SMS) from other binaries we load into the chip by
default.
One way ROM does this is by enabling firewalls to protect the OCSRAM
region it's using during bootup. Only after TIFS has started (and had
time to disable the OCSRAM firewall region) will we have write access to
the region.
This means we will need to move the stack & heap from OCSRAM to HSM RAM
and reduce the size of BSS and the SPL to allow it to fit properly.
Signed-off-by: Bryan Brattlof <bb@ti.com>
In its current form, the am62a's wakeup SPL is fairly small, however
this will not remain as more boot modes are eventually added. To protect
us from overflowing our ~256k of HSM SRAM, add limits and check during
the wakeup SPL build.
Signed-off-by: Bryan Brattlof <bb@ti.com>
TI boards use a custom (though faily common to TI boards) mechanism for
booting Linux. We would like to use the "distroboot" approach.
Enable distroboot as a further option to use for booting on am625 should
the existing options fail.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
In f422c4bec the configuration option to support s28hs512t SPI flashes
was changed from CONFIG_SPI_FLASH_S28HS512T to CONFIG_SPI_FLASH_S28HX_T
to support the wider family. Follow this change in the AM62x EVM
configurations.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Activate by default CONFIG_ENV_MMC_USE_DT as "u-boot,mmc-env-partition"
should be always use in STMicroelectronics boards device tree to locate
the environment for mmc backend. The 2 defines:
CONFIG_ENV_OFFSET=0x280000
CONFIG_ENV_OFFSET_REDUND=0x2C0000
are only valid for spi-nor and not for SD-Card or eMMC.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
For some newer SoCs like RK3568, the Rockchip has not released
any DDR drivers yet so idbloader needs to create manually using
DDR binaries offered by rkbin. This indeed no requirement to
enable TPL in the U-Boot source code.
If we mark TPL disabled and mark BINMAN enabled by default then
there would be an issue of binman_init failure during board
relocation. This is true as binman failed to find the top-level
node like u-boot-tpl here.
Here is the boot issue observed in Radxa-CM3 RK3566 board,
U-Boot 2023.01-rc4-00057-gac2505d463-dirty (Jan 04 2023 - 23:44:18 +0530)
Model: Radxa Compute Module 3(CM3) IO Board
DRAM: 2 GiB
binman_init failed:-2
initcall sequence 000000007ffd2008 failed at call 0000000000a18cac (err=-2)
### ERROR ### Please RESET the board ###
This might be fixed via binman node in rockchip-u-boot.dtsi however
disable BINMAN_FDT for evb-rk3568 defconfig for now as we are at the
end of the release cycle.
Fixes: 05713d5707 ("rockchip: generate u-boot-rockchip.bin with binman
for ARM64 boards")
Cc: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmO2mnEcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyBAOB/4y7e9y0jdKSWDwMdZj
enXK/U/GREFyuiSdadil0aJl9WfayjwZkh7uHSTj4pi9ApNivfoqsL7WZYpJxhRD
WlpNhs3TZ70i8CgKUosdzcpquAQZUZhg6iV5DCObrK6yNJRGOXLIwMOd+vw/Xz6/
YTGqzivEDMBuH/9HLuC0m+26PEpff8nenNEjC2k8ssG26ojLz7oCQh2HoHcSgNRc
HkEYlFJ/Le8kM8Ak2F3ebmsfgMTnFrRVwV1BsZa5vO0BrMYgJCORsl7Cnfcw6/2N
LEHG7kwlSorJeETn/gkLiZ+NyqzU+oFH0jGRZ5Ciqg1qcCO3k9yBMgWQzd7nTL6C
5oZA
=Ocdd
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2023.04-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2023.04 cycle:
This feature set includes the new DM-based NAND flash driver (old non-DM
driver is still kept for backwards compatibility), and the move to DM
NAND flash driver for sam9x60ek board. Feature set also includes
devicetree alignment for sama7g5 with Linux, devicetree alignment on USB
with Linux for all boards (sama5, sam9x60), chip id for sama7g5, minor
configs and tweaks.
Due to the part shortage, the AR8031 PHY was replaced with a
Micrel KSZ9131. Enabling both config options keeps backward
compatibility with either platform, and both appear to be
auto-detected.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Video out on RK3288 boards has been broken since from few
releases due to the adding of reset support on vop but
missed enabling DM_RESET on associated boards.
This patch fixes those RK3288 boards.
Cc: Simon Glass <sjg@chromium.org>
Cc: Lin Huang <hl@rock-chips.com>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
Fixes: <9749d2ea29e1> ("rockchip: video: vop: Add reset support")
Reported-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove init of UART-clock and UART-reset in arch_cpu_init(). Add DEBUG_UART
to s5p4418_nanopi2_defconfig.
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
Switch off SCSI related config options to get rid of the board
removal warning. We don't use this interface. Also disable UBIFS
to decrease the image size, as this is also not used.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
Support Holtek HT1380/HT1381 Serial Timekeeper Chip. It provides seconds
, minutes, hours, day of the week, date, month and year information.
Datasheet:
https://www.holtek.com.tw/documents/10179/11842/ht1380_1v130.pdf
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
All uniphier v7 SoCs have cortex-a9 and use cortex-a9 global timer
in a simple implementation. Now DM_TIMER of it is available
on 35751c7f3f ("timer: sti: convert sti-timer to arm a9 global timer"),
so let's switch to it.
The old driver reads the lower 32bits of counter field
and sets the prescaler as 50 with PERIPHCLK(=50MHz),
so the global timer works as a 32-bit 1MHz timer.
The DM_TIMER uses the whole 64bits with no prescaler,
so the global timer works as a 64-bit PERIPHCLK timer.
CONFIG_SYS_HZ_CLOCK is set as the default PERIPHCLK frequency,
if there is no 'clocks' property in devicetree.
Signed-off-by: Dai Okamura <okamura.dai@socionext.com>
In 96699f097a ("powerpc: mpc85xx: Use binman to embed dtb inside
U-Boot") we introduce CONFIG_MPC85XX_HAVE_RESET_VECTOR and do so via
Kconfig. However, much later in de47ff5363 ("Convert
CONFIG_SYS_MPC85XX_NO_RESETVEC to Kconfig") I converted the symbol that
is the inverse of this to Kconfig. This should have included a
dependency on the first symbol as they are logically opposite.
The dependency being missing lead to some platforms being broken at
runtime due to discarding the require reset vector.
Fixes: de47ff5363 ("Convert CONFIG_SYS_MPC85XX_NO_RESETVEC to Kconfig")
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Pali Rohár <pali@kernel.org>
When converting CONFIG_SDCARD and CONFIG_SPIFLASH to Kconfig, one set of
uses wasn't converted correctly. Allow for the case where platforms
don't rely on "PBL" to boot but instead use other mechanisms. See the
link below for more details.
Link: https://lore.kernel.org/all/20220802091338.f4g45ldhc7qbg6hm@pali/
Fixes: d433c74eec ("Convert CONFIG_SDCARD et al to Kconfig")
Tested-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
As of 2f41ade79e ("linker: Modify linker scripts to be more generic")
we can use the same linker script for SPL and TPL and not have to make
use of #undef tricks. Remove these last remnants.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_TEGRA_ENABLE_UARTA
CONFIG_TEGRA_ENABLE_UARTB
CONFIG_TEGRA_ENABLE_UARTC
CONFIG_TEGRA_ENABLE_UARTD
CONFIG_TEGRA_SPI
CONFIG_TEGRA_UARTA_GPU
CONFIG_TEGRA_UARTA_SDIO1
CONFIG_TEGRA_VDD_CORE_TPS62361B_SET3
CONFIG_TEGRA_VDD_CORE_TPS62366A_SET1
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_MONITOR_IS_IN_RAM
As part of this, reword some of the documentation slightly to reflect
that this is in Kconfig and not a define now.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_GATEWAYIP
CONFIG_HOSTNAME
CONFIG_IPADDR
CONFIG_NETMASK
CONFIG_ROOTPATH
CONFIG_SERVERIP
CONFIG_UBOOTPATH
To do this, we introduce a CONFIG_USE_ form of each of the above and
change include/env_default.h to test for that to be set before setting a
value. Further, we don't want to stringify the IP address related values
as they are now properly strings via Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_FLASH_SPANSION_S29WS_N
CONFIG_FLASH_VERIFY
CONFIG_FSL_FM_10GEC_REGULAR_NOTATION
CONFIG_FSL_ISBC_KEY_EXT
CONFIG_FSL_TRUST_ARCH_v1
CONFIG_FSL_SDHC_V2_3
CONFIG_MAX_DSP_CPUS
CONFIG_MIU_2BIT_INTERLEAVED
CONFIG_SERIAL_BOOT
CONFIG_SPI_BOOTING
CONFIG_X86EMU_RAW_IO
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_DM9000_BYTE_SWAPPED
CONFIG_DM9000_NO_SROM
CONFIG_DM9000_USE_16BIT
CONFIG_DM9000_DEBUG
CONFIG_MXC_GPT_HCLK
CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable the UEFI capsule update functionality on the RockPi4B and
RockPi4C boards. Support is being enabled for updating the idbloader
and u-boot firmware images residing on GPT partitioned uSD card
storage device.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The GPT table is taking the first 34 sectors, which amounts to 0x4400
bytes. Saving the environment below this address in storage will corrupt
the GPT table.
While technically the table ends at 0x4400, some tools (e.g. bmaptool)
are rounding everything to the logical block size (0x1000), so it is
safer to make it point to 0x5000 so that the environment could still
persist when flashing a sparse image with bmaptool or similar tools.
Obviously, the default 0x4000 environment size does not work anymore, so
let's set it to 0x3000 so it does fill the gap between the GPT table
(rounded to 0x1000) and the start of the idbloader.img.
Fixes: 56f580d3eb ("rockchip: dts: rk3399-puma: put environment (in MMC/SD configurations) before SPL")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
this patch add USB mass storage function and Rockusb function for
Radxa ROCK Pi 4 series.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This patch enables the following:
1) use preboot configuration to enable usb devices.
2) Enable USB configs so keyboards and other USB devices work,
update the number of ports of the usb root hub.
- with this addition the updated USB device Tree:
1 Hub (12 Mb/s, 0mA)
U-Boot Root Hub
1 Hub (12 Mb/s, 0mA)
| U-Boot Root Hub
|
+-2 Hub (12 Mb/s, 100mA)
USB 2.0 Hub [MTT]
1 Hub (5 Gb/s, 0mA)
U-Boot XHCI Host Controller
3) enable crypto RNG support.
4) Change SPI speed and frequency:
- increase the maximum SPI slave device speed,
SPI flash max frequency for the environment from 10Mhz to 30MHz.
- performance stats for speed update from 10MHz to 30MHz:
with 10Mhz speed update:
=> sf update 0x300000 0x800000 0x400000
4194304 bytes written, 0 bytes skipped in 36.819s, speed 119837 B/s
with 30Mhz speed update:
=> sf update 0x300000 0x800000 0x400000
4194304 bytes written, 0 bytes skipped in 20.319s, speed 220752 B/s
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Da Xue <da.xue@libretech.co>
Signed-off-by: dsx724 <da@lessconfused.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
add CONFIG_OF_LIBFDT_OVERLAY=y to support fdt overlays.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This cleans up each board's defconfig, and fixes the serial console on
some Olimex board. Also we lose another legacy config variable.
The rest are minor cleanups, that actually shouldn't change anything
in the build.
Passed the gitlab CI, plus briefly tested on Pine64-LTS, LicheePi Nano,
and BananaPi M1.
At present U-Boot no longer builds as a complete rom for som-db5800-som-6867.
BINMAN .binman_stamp
Wrote map file './rom.map' to show errors
binman: Section '/binman/rom': contents size 0x80302c (8400940) exceeds section size 0x800000 (8388608)
Checking rom.map we see 'intel-vga' section is overlapped with
other sections:
<none> fff00000 0009f7c8 u-boot-with-ucode-ptr
<none> fff90000 00010000 intel-vga
<none> fff9f7c8 00001aae u-boot-dtb-with-ucode
Let's adjust CONFIG_TEXT_BASE to allow more space for U-Boot codes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present U-Boot no longer builds as a complete rom for all the
configs of dfi-bt700.
BINMAN .binman_stamp
Wrote map file './rom.map' to show errors
binman: Section '/binman/rom': contents size 0x80e836 (8448054) exceeds section size 0x800000 (8388608)
Checking rom.map we see 'intel-vga' section is overlapped with
other sections:
<none> fff00000 000aac90 u-boot-with-ucode-ptr
<none> fffa0000 00010000 intel-vga
<none> fffaac90 00001df0 u-boot-dtb-with-ucode
<none> fffaca80 00019800 u-boot-ucode
Let's adjust CONFIG_TEXT_BASE to allow more space for U-Boot codes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
At present U-Boot no longer builds as a complete rom for all the
configs of conga-qeval20-qa3-e3845.
BINMAN .binman_stamp
Wrote map file './rom.map' to show errors
binman: Section '/binman/rom': contents size 0x80b680 (8435328) exceeds section size 0x800000 (8388608)
Checking rom.map we see 'intel-vga' section is overlapped with
other sections:
<none> fff00000 000a7cb0 u-boot-with-ucode-ptr
<none> fffa0000 00010000 intel-vga
<none> fffa7cb0 00001c1a u-boot-dtb-with-ucode
<none> fffa98d0 00019800 u-boot-ucode
Let's adjust CONFIG_TEXT_BASE to allow more space for U-Boot codes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present U-Boot no longer builds as a complete rom for minnowmax.
BINMAN .binman_stamp
Wrote map file './rom.map' to show errors
binman: Section '/binman/rom': contents size 0x803146 (8401222) exceeds section size 0x800000 (8388608)
Checking rom.map we see 'fdtmap' section is overlapped with
'intel-vga' section:
<none> fffa1390 00019800 u-boot-ucode
<none> fffb0000 00010000 intel-vga
<none> fffbab90 00000539 fdtmap
Let's adjust CONFIG_TEXT_BASE to allow more space for U-Boot codes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present U-Boot no longer builds as a complete rom for bayleybay.
BINMAN .binman_stamp
Wrote map file './rom.map' to show errors
binman: Section '/binman/rom': contents size 0x814706 (8472326) exceeds section size 0x800000 (8388608)
Checking rom.map we see 'fdtmap' section is overlapped with
'intel-vga' and 'intel-fsp' sections:
<none> fffa2150 0002a000 u-boot-ucode
<none> fffb0000 00010000 intel-vga
<none> fffc0000 00038000 intel-fsp
<none> fffcc150 00000539 fdtmap
Let's adjust CONFIG_TEXT_BASE to allow more space for U-Boot codes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
On this board CONFIG_CONS_INDEX needs to be 1 unlike other sun5i
boards. Since this is the default, remove to bogus setting.
Fixes: 7095f86418 ("sunxi: Convert CONS_INDEX to Kconfig")
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Commit 08574ed339 ("Convert CONFIG_SYS_MONITOR_LEN to Kconfig") moved
the definition of said config variable from the common sunxi header to
*every board's* defconfig.
This is a platform choice, not board specific, so remove the variable
from there, instead set the one value for all Allwinner boards in
Kconfig.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Use like the other boards a text file for the environment.
As this is the last user of keymile-common.h we can now remove this
file completely.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
Use already present common.env file and add a powerpc specific env
so that we can move all the environment defines to text files.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
Replace MTDPARTS_DEFAULT in the config include file by
CONFIG_MTDPARTS_DEFAULT in defconfig to complete the Kconfig migration.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
