Patches that added the Tegra210 pinctrl driver and renamed directories
arch/arm/cpu/tegra{$soc}-common -> arch/arm/mach-tegra/tegra-${soc}
crossed. Move the Tegra210 pinctrl driver to the correct location. This
wasn't detected since Tegra210 support is in the process of being added,
and isn't buildable yet.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
make the CPU clock selectable via Kconfig
this removes the sunxi specific CONFIG_CLK_FULL_SPEED defined in each
soc header and replaces it's use in board/sunxi/board.c with
CONFIG_SYS_CLK_FREQ from Kconfig which allows us to configure board
specific frequency on boot
Signed-off-by: Iain Paton <ipaton0@gmail.com>
[hdegoede@redhat.com s/CONFIG_SYS_CLK_FREQ/CONFIG_TIMER_CLK_FREQ/ for the
arch-timer clk speed on sun7i to fix mis-compile on sun7i]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
clock_set_pll1 would pick the next highest available cpu clock speed if
a value not in the pre defined table was selected. this potentially
results in overclocking the soc.
reverse the selection method so that we select the next lowest speed
and add the missing 912Mhz setting that's requested by sun7i which also
uses the sun4i clock code.
Signed-off-by: Iain Paton <ipaton0@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The usb0 / otg phy on sunxi boards has a bug where it wrongly detects a
high speed squelch on usb reset deassert when a lo speed device is plugged in.
The android kernel has a work around for this in the form of temporary
disabling the phy's squelch detection on reset deassert, this commit adds
the same workaround to the u-boot sunxi musb code, thereby fixing various usb
lo speed devices not working.
Tested with a (before non working) usb keyboard and a usb 2.4 GHz wireless
keyboard/mouse combo receiver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
BCM2835 (used on Raspberry Pi) and BCM2836 (used on Raspberry Pi 2)
are similar enough. One of the biggest differences is the ARM
processor. It is reasonable to collect the source files into a
single place, arch/arm/mach-bcm283x/.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
This option has a bool type, not hex.
Fix it and enable it if CONFIG_DM is on because Driver Model always
requires malloc memory. Devices are scanned twice, before/after
relocation. CONFIG_SYS_MALLOC_F should be enabled to use malloc
memory before relocation. As it is board-independent, handle it
globally.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Robert Baldyga <r.baldyga@samsung.com>
The default value of CONFIG_SYS_MALLOC_F_LEN is defined by ./Kconfig
as 0x400. Each defconfig or Kconfig need not repeat the same value.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Robert Baldyga <r.baldyga@samsung.com>
My main motivations for this commit are:
[1] Follow the arch/arm/Makefile style of Linux Kernel
[2] Maintain compiler options systematically
Currently, we give -march=* and -mtune=* options inconsistently:
Only some of the CPUs pass -march=* and -mtune=* options.
By collecting such options into the single place arch/arm/Makefile
we can tell which options are missing at a glance.
[3] Prepare for deprecating arch/*/cpu/*/config.mk
Note:
This commit just moves the compiler options so as not to change
the behavior at all. It does not care about the correctness of
the given options. Fox example, "-march=armv5te" might be better
than "-march=armv4" for ARM946EJS, but it is beyond the scope this
commit. Also, filling the missing -march=* and -tune=* is left
to follow-up patches.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Various files are needlessly rebuilt every time due to the version and
build time changing. As version.h is not actually needed, remove the
include.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Macpaul Lin <macpaul@andestech.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: York Sun <yorksun@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Philippe Reynes <tremyfr@yahoo.fr>
Cc: Eric Jarrige <eric.jarrige@armadeus.org>
Cc: "David Müller" <d.mueller@elsoft.ch>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Robert Baldyga <r.baldyga@samsung.com>
Cc: Torsten Koschorrek <koschorrek@synertronixx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Łukasz Majewski <l.majewski@samsung.com>
Add basic SECO MX6Q/uQ7 board support (Ethernet, UART, SD are supported).
It also adds a Kconfig skeleton to later add more SECO board (supporting
SoC and board variants).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Freescale boards are currently all defined in arch/arm/Kconfig, which
makes them hard to detect.
Moreover the MX6 SoC variant (Q, D, DL, S, SL) selection is currently
done via the SYS_EXTRA_OPTIONS option which marked as deprecated.
Move to a more standard way to select sub-architecture and board by
creating a Kconfig under arch/arm/cpu/armv7/mx6 and a new ARCH_MX6
option.
Existing MX6 board definitions should be moved in this new Kconfig in
choice menu, and new boards should be directly declared in this menu.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
RX51 has a secure logic which uses different parameters compared to
traditional implementation. So, make the generic secure acr write
over-ride-able by board file and refactor rx51 code to use this.
While at it, enable the OMAP3 specific errata code for 454179, 430973,
621766.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable the OMAP3 specific errata code for 454179, 430973, 621766
and while at it, remove legacy non-revision checked errata logic.
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update to existing recommendation for L2ACTLR configuration to prevent
system instability and optimize performance.
These apply to both OMAP5 and DRA7.
Reported-by: Vivek Chengalvala <vchengalvala@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch enables the workaround for ARM errata 798870 for OMAP5 /
DRA7 which says "If back-to-back speculative cache line fills (fill
A and fill B) are issued from the L1 data cache of a CPU to the
L2 cache, the second request (fill B) is then cancelled, and the
second request would have detected a hazard against a recent write or
eviction (write B) to the same cache line as fill B then the L2 logic
might deadlock."
An l2auxctlr accessor implementation for OMAP5 and DRA7 is introduced
here as well.
Signed-off-by: Praveen Rao <prao@ti.com>
Signed-off-by: Angela Stegmaier <angelabaker@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
omap_smc1 is now generic enough to remove duplicate
omap3_gp_romcode_call logic that omap3 introduced.
As part of this change, move to using the generic lowlevel_init.S for
omap3 as well.
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
set_pl310_ctrl_reg does use the Secure Monitor Call (SMC) to setup
PL310 control register, however, that is something that is generic
enough to be used for OMAP5 generation of processors as well. The only
difference being the service being invoked for the function.
So, convert the service to a macro and use a generic name (same as
that used in Linux for some consistency). While at that, also add a
data barrier which is necessary as per recommendation.
While at this, smc #0 is maintained as handcoded assembly thanks to
various gcc version eccentricities, discussion thread:
http://marc.info/?t=142542166800001&r=1&w=2
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
621766: Under a specific set of conditions, executing a sequence of
NEON or vfp load instructions can cause processor deadlock
Impacts: Every Cortex-A8 processors with revision lower than r2p1
Work around: Set L1NEON to 1
Based on ARM errata Document revision 20.0 (13 Nov 2010)
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
430973: Stale prediction on replaced inter working branch causes
Cortex-A8 to execute in the wrong ARM/Thumb state
Impacts: Every Cortex-A8 processors with revision lower than r2p1
Work around: Set IBE to 1
Based on ARM errata Document revision 20.0 (13 Nov 2010)
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
454179: Stale prediction may inhibit target address misprediction on
next predicted taken branch
Impacts: Every Cortex-A8 processors with revision lower than r2p1
Work around: Set IBE and disable branch size mispredict to 1
Also provide a hook for SoC specific handling to take place if needed.
Based on ARM errata Document revision 20.0 (13 Nov 2010)
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add workaround for Cortex-A15 ARM erratum 798870 which says
"If back-to-back speculative cache line fills (fill A and fill B) are
issued from the L1 data cache of a CPU to the L2 cache, the second
request (fill B) is then cancelled, and the second request would have
detected a hazard against a recent write or eviction (write B) to the
same cache line as fill B then the L2 logic might deadlock."
Implementations for SoC families such as Exynos, OMAP5/DRA7 etc
will be widely different.
Every SoC has slightly different manner of setting up access to L2ACLR
and similar registers since the Secure Monitor handling of Secure
Monitor Call(smc) is diverse. Hence an weak function is introduced
which may be overriden to implement SoC specific accessor implementation.
Based on ARM errata Document revision 18.0 (22 Nov 2013)
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Matt Porter <mporter@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Disable the warm reset and enable the cold reset for a more reliable
restart ('reset'). This is taken from the Linux kernel, see imx_src_init()
in arch/arm/mach-imx/src.c.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
While the Freescale ARMv8 board LS2085A will enter U-Boot both
on a master and a secondary (slave) CPU, this is not the common
behaviour on ARMv8 platforms. The norm is that U-Boot is entered
from the master CPU only, while the other CPUs are kept in
WFI (wait for interrupt) state.
The code determining which CPU we are running on is using the
MPIDR register, but the definition of that register varies with
platform to some extent, and handling multi-cluster platforms
(such as the Juno) will become cumbersome. It is better to only
enable the multiple entry code on machines that actually need
it and disable it by default.
Make the single entry default and add a special
ARMV8_MULTIENTRY KConfig option to be used by the
platforms that need multientry and set it for the LS2085A.
Delete all use of the CPU_RELEASE_ADDR from the Vexpress64
boards as it is just totally unused and misleading, and
make it conditional in the generic start.S code.
This makes the Juno platform start U-Boot properly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The way the PSCI DT update happens currently means we pull in
<asm/armv7.h> everywhere, including on ARMv8 and that in turn brings in
<asm/io.h> for some non-PSCI related things that header needs to deal
with.
To fix this, we rework the hook slightly. A good portion of
arch/arm/cpu/armv7/virt-dt.c is common looking and I hope that when PSCI
is needed on ARMv8 we can re-use this by and large. So rename the
current hook to psci_update_dt(), move the prototype to <asm/psci.h> and
add an #ifdef that will make re-use later easier.
Reported-by: York Sun <yorksun@freescale.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: York Sun <yorksun@freescale.com>
The 'nandecc sw' command selects a software-based error correction
algorithm. By default, this is OMAP_ECC_HAM1_CODE_SW but some
platforms use OMAP_ECC_BCH8_CODE_HW_DETECTION_SW as their
software-based correction algorithm. Allow a user to be specific e.g.
# nandecc sw <hamming|bch8>
where 'hamming' is still the default.
Note: we don't just use CONFIG_NAND_OMAP_ECCSCHEME as it might be set
to a hardware-based ECC scheme---a little strange when the user
has requested 'sw' ECC.
Signed-off-by: Ash Charles <ashcharles@gmail.com>
This patch extends OMAP3 support for AM/DM37xx and
introduces the AM3703-based Quipos Cairo board.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Reviewed-by: Simon Glass <sjg@chromium.org>
According to table 2-3 on page 87 of Marvell's latest PXA270
Specification Update Rev. I from 2010.04.19 [1] there exists a breed of
chips with a new CPU ID for PXA270M A1 stepping which our latest
Colibri PXA270 V2.4A modules actually have assembled. This patch helps
in correctly identifying those chips upon boot as well which then looks
as follows:
CPU: Marvell PXA27xM rev. A1
[1] http://www.marvell.com/application-processors/pxa-family/assets/pxa_27x_spec_update.pdf
Acked-by: Marek Vasut <marex@denx.de>
Currently in some cases SDRAM init requires global_data to be available
and soon this will not be available prior to board_init_f(). Adjust the
code paths in these cases to be correct. In some cases we had the SPL
stack be in DDR as we might have large stacks (due to Falcon Mode +
Environment). In these cases switch to CONFIG_SPL_STACK_R. In other
cases we had simply been setting CONFIG_SPL_STACK into SRAM. In these
cases we no longer need to (CONFIG_SYS_INIT_SP_ADDR is used and is also
in SRAM) so drop those lines.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested on Beagleboard, Beagleboard xM
Tested-by: Matt Porter <mporter@konsulko.com>
Tested on Beaglebone Black, AM43xx GP EVM, OMAP5 uEVM, OMAP4 Pandaboard
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This function has grown into something of a monster. Some boards are setting
up a console and DRAM here in SPL. This requires global_data which should be
set up in one place (crt0.S).
There is no need for SPL to use s_init() for anything since board_init_f()
is called immediately afterwards.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch incorporates a few fixes from Tom Warren <twarren@nvidia.com>.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add basic Xilinx ZynqMP arm64 support.
Serial and SD is supported.
It supports emulation platfrom ep108 and QEMU.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Since commit 3ff46cc42b ("arm: relocate the exception vectors") mx35
does not boot anymore.
Add a specific relocate_vectors macro that skips the vector relocation, as the
i.MX35 SoC does not provide RAM at the high vectors address (0xFFFF0000), and
(0x00000000) maps to ROM.
This allows mx35 to boot again.
Cc: Sebastian Priebe <sebastian.priebe@cadcon.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Since commit 3ff46cc42b ("arm: relocate the exception vectors") mx31
does not boot anymore.
Add a specific relocate_vectors macro that skips the vector relocation, as the
i.MX31 SoC does not provide RAM at the high vectors address (0xFFFF0000), and
(0x00000000) maps to ROM.
This allows mx31 to boot again.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
If CONFIG_ARMV7_PSCI is not defined and CONFIG_ARMV7_SECURE_BASE is defined,
smp_kicl_all_cpus may enable secondary cores and runs into secure_ram_addr(
_smp_pen), before code is relocated to secure ram.
So need relocation to secure ram before enable secondary cores.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
It was found that the L2 cache timings that we had before could cause
freezes and hangs. We should make things more robust with better
timings. Currently the production ChromeOS kernel applies these
timings, but it's nice to fixup firmware too (and upstream probably
won't take our kernel hacks).
This also provides a big cleanup of the L2 cache init code avoiding
some duplication. The way things used to work:
* low_power_start() was installed by the SPL (both at boot and resume
time) and left resident in iRAM for the kernel to use when bringing
up additional CPUs. It used configure_l2_ctlr() and
configure_l2_actlr() when it detected it was on an A15. This was
needed (despite the L2 cache registers being shared among all A15s)
because we might have been the first man in after the whole A15
cluster was shutdown.
* secondary_cores_configure() was called on at boot time and at resume
time. Strangely this called configure_l2_ctlr() but not
configure_l2_actlr() which was almost certainly wrong. Given that
we'll call both (see next bullet) later in the boot process it
didn't matter for normal boot, but I guess this is how L2 cache
settings got set on 5420/5800 (but not 5250?) at resume time.
* exynos5_set_l2cache_params() was called as part of cache enablement.
This should happen at boot time (normally in the SPL except for USB
boot where it happens in main U-Boot).
Note that the old code wasn't setting ECC/parity in the cache
enablement code but we happened to get it anyway because we'd call
secondary_cores_configure() at boot time. For resume time we'd get it
anyway when the 2nd A15 core came up.
Let's make this a whole lot simpler. Now we always set these
parameters in the same place for all boots and use the same code for
setting up secondary CPUs.
Intended net effects of this change (other than cleanup):
* Timings go from before:
data: 0 cycle setup, 3 cycles (0x2) latency
tag: 0 cycle setup, 3 cycles (0x2) latency
after:
data: 1 cycle setup, 4 cycles (0x3) latency
tag: 1 cycle setup, 4 cycles (0x3) latency
* L2ACTLR is properly initted on 5420/5800 in all cases.
One note is that we're still relying on luck to keep low_power_start()
working. The compiler is being nice and not storing anything on the
stack.
Another note is that on its own this patch won't help to fix cache
settings in an RW U-Boot update where we still have the RO SPL. The
plan for that is:
* Have RW U-Boot re-init the cache right before calling the kernel
(after it has turned the L2 cache off). This is why the functions
are in a header file instead of lowlevel_init.c.
* Have the kernel save the L2 cache settings of the boot CPU and apply
them to all other CPUs. We get a little lucky here because the old
code was using "|=" to modify the registers and all of the bits that
it's setting are also present in the new settings (!). That means
that when the 2nd CPU in the A15 cluster comes up it doesn't
actually mess up the settings of the 1st CPU in the A15 cluster. An
alternative option is to have the kernel write its own
low_power_start() code.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
On warm reset, all cores jump to the low_power_start function because iRAM
data is retained and because while executing iROM code all cores find
the jump flag 0x02020028 set. In low_power_start, cores check the reset
status and if true they clear the jump flag and jump back to 0x0.
The A7 cores do jump to 0x0 but consider following instructions as a Thumb
instructions which in turn makes them loop inside the iROM code instead of
jumping to power_down_core.
This issue is fixed by replacing the "mov pc" instruction with a "bx"
instruction which switches state along with the jump to make the execution
unit consider the branch target as an ARM instruction.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
When compiled SPL for Thumb secondary cores failed to boot
at the kernel boot up. Only one core came up out of 4.
This was happening because the code relocated to the
address 0x02073000 by the primary core was an ARM asm
code which was executed by the secondary cores as if it
was a thumb code.
This patch fixes the issue of secondary cores considering
relocated code as Thumb instructions and not ARM instructions
by jumping to the relocated with the help of "bx" ARM instruction.
"bx" instruction changes the 5th bit of CPSR which allows
execution unit to consider the following instructions as ARM
instructions.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch does 3 things:
1. Enables ECC by setting 21st bit of L2CTLR.
2. Restore data and tag RAM latencies to 3 cycles because iROM sets
0x3000400 L2CTLR value during switching.
3. Disable clean/evict push to external by setting 3rd bit of L2ACTLR.
We need to restore this here due to switching.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
L2 Auxiliary Control Register provides configuration
and control options for the L2 memory system. Bit 3
of L2ACTLR stands for clean/evict push to external.
Setting bit 3 disables clean/evict which is what
this patch intends to do.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
iROM logic provides undesired jump address for CPU2.
This patch adds a programmable susbstitute for a part of
iROM logic which wakes up cores and provides jump addresses.
This patch creates a logic to make all secondary cores jump
to a particular address which evades the possibility of CPU2
jumping to wrong address and create undesired results.
Logic of the workaround:
Step-1: iROM code checks value at address 0x2020028.
Step-2: If value is 0xc9cfcfcf, it jumps to the address (0x202000+CPUid*4),
else, it continues executing normally.
Step-3: Primary core puts secondary cores in WFE and store 0xc9cfcfcf in
0x2020028 and jump address (pointer to function low_power_start)
in (0x202000+CPUid*4).
Step-4: When secondary cores recieve event signal they jump to this address
and continue execution.
Signed-off-by: Kimoon Kim <kimoon.kim@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds code to shutdown secondary cores.
When U-boot comes up, all secondary cores appear powered on,
which is undesirable and causes side effects while
initializing these cores in kernel.
Secondary core power down happens in following steps:
Step-1: After Exynos power-on, primary core starts executing first.
Step-2: In iROM code every core has to check 2 flags i.e.
addresses 0x02020028 & 0x02020004.
Step-3: Initially 0x02020028 is 0 for all cores and 0x02020004 has a
jump address for primary core and 0 for all secondary cores.
Step-4: Therefore, primary core follows normal iROM execution and jumps
to BL1 eventually, whereas all secondary cores enter WFE.
Step-5: When primary core comes into function secondary_cores_configure,
it puts pointer to function power_down_core into 0x02020004
and provides DSB and SEV for all cores so that they may come out
of WFE and jump to power_down_core function.
Step-6: And ultimately because of power_down_core all
secondary cores shut-down.
Signed-off-by: Kimoon Kim <kimoon.kim@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
ED Mini V2 is based on Orion 5x which boots at fixed
address 0xFFFF0000 in NOR Flash. Place SPL there, and
switch U-Boot from .bin to .img format, stored in
NOR Flash at 0xFFF90000.
Note: this patch was tested on HW and works, i.e.
it boots U-Boot properly, but SPL console output
currently does not appear, due to GD being trashed
by arch/arm/lib/spl.c. This trashing is soon to be
removed, and then ED Mini V2 SPL console output will
become visible.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Porter is an entry level development board based on R-Car M2 SoC (R8A7791)
This commit supports the following peripherals:
- SCIF, I2C, Ethernet, QSPI, SD, USB Host
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Lager board has two SDHI port as SDHI0 and SDHI2.
This adds GPIO configuration and initialization function of SDHI, and
enables MMC command.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Alt board has two SDHI port.
This adds GPIO configuration and initialization function of SDHI, and
enables MMC command.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Chan-Taek Park <c-park@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
This is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Po-Yu Chuang <ratbert@faraday-tech.com>
Acked-by: Marek Vasut <marex@denx.de>
These are still non-generic boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Greg Ungerer <greg.ungerer@opengear.com>
Acked-by: Marek Vasut <marex@denx.de>
This is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Lei Wen <leiwen@marvell.com>
Acked-by: Marek Vasut <marex@denx.de>
This is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Matthias Weisser <weisserm@arcor.de>
Acked-by: Marek Vasut <marex@denx.de>
Now CONFIG_SPL_BUILD is not defined in Kconfig, so
"!depends on SPL_BUILD" and "if !SPL_BUILD" are redundant.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
When Kconfig for U-boot was examined, one of the biggest issues was
how to support multiple images (Normal, SPL, TPL). There were
actually two options, "single .config" and "multiple .config".
After some discussions and thought experiments, I chose the latter,
i.e. to create ".config", "spl/.config", "tpl/.config" for Normal,
SPL, TPL, respectively.
It is true that the "multiple .config" strategy provided us the
maximum flexibility and helped to avoid duplicating CONFIGs among
Normal, SPL, TPL, but I have noticed some fatal problems:
[1] It is impossible to share CONFIG options across the images.
If you change the configuration of Main image, you often have to
adjust some SPL configurations correspondingly. Currently, we
cannot handle the dependencies between them. It means one of the
biggest advantages of Kconfig is lost.
[2] It is too painful to change both ".config" and "spl/.config".
Sunxi guys started to work around this problem by creating a new
configuration target. Commit cbdd9a9737 (sunxi: kconfig: Add
%_felconfig rule to enable FEL build of sunxi platforms.) added
"make *_felconfig" to enable CONFIG_SPL_FEL on both images.
Changing the configuration of multiple images in one command is a
generic demand. The current implementation cannot propose any
good solution about this.
[3] Kconfig files are getting ugly and difficult to understand.
Commit b724bd7d63 (dm: Kconfig: Move CONFIG_SYS_MALLOC_F_LEN to
Kconfig) has sprinkled "if !SPL_BUILD" over the Kconfig files.
[4] The build system got more complicated than it should be.
To adjust Linux-originated Kconfig to U-Boot, the helper script
"scripts/multiconfig.sh" was introduced. Writing a complicated
text processor is a shell script sometimes caused problems.
Now I believe the "single .config" will serve us better. With it,
all the problems above would go away. Instead, we will have to add
some CONFIG_SPL_* (and CONFIG_TPL_*) options such as CONFIG_SPL_DM,
but we will not have much. Anyway, this is what we do now in
scripts/Makefile.spl.
I admit my mistake with my apology and this commit switches to the
single .config configuration.
It is not so difficult to do that:
- Remove unnecessary processings from scripts/multiconfig.sh
This file will remain for a while to support the current defconfig
format. It will be removed after more cleanups are done.
- Adjust some makefiles and Kconfigs
- Add some entries to include/config_uncmd_spl.h and the new file
scripts/Makefile.uncmd_spl. Some CONFIG options that are not
supported on SPL must be disabled because one .config is shared
between SPL and U-Boot proper going forward. I know this is not
a beautiful solution and I think we can do better, but let's see
how much we will have to describe them.
- update doc/README.kconfig
More cleaning up patches will follow this.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is true that malloc is necessary for Driver Model before
relocation, but there is no good reason to reserve the malloc
space more than enough. The default value 0x400 works well.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The RCPM FSM may not be reset after power-on, for example,
in the cases of cold boot and wakeup from deep sleep.
It causes cache coherency problem and may block deep sleep.
Therefore, reset them if they are not be reset.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LS1021A's PCIe1 region begins 0x40_00000000; PCIe2 begins
0x48_00000000. In order to access PCIe device, we must create
TLB to map the 40bit physical address to 32bit virtual address.
This patch will enable MMU after DDR is available and creates MMU
table in DRAM to map all 4G space; then, re-use the reserved space
to map PCIe region. The following the mapping layout.
VA mapping:
------- <---- 0GB
| |
| |
|-------| <---- 0x24000000
|///////| ===> 192MB VA map for PCIe1 with offset 0x40_0000_0000
|-------| <---- 0x300000000
| |
|-------| <---- 0x34000000
|///////| ===> 192MB VA map for PCIe2 with offset 0x48_0000_0000
|-------| <---- 0x40000000
| |
|-------| <---- 0x80000000 DDR0 space start
|\\\\\\\|
|\\\\\\\| ===> 2GB VA map for 2GB DDR0 Memory space
|\\\\\\\|
------- <---- 4GB DDR0 space end
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Upgrade Manage Complex (MC) flib API to 0.5.2. Rename directory
fsl_mc to fsl-mc. Change the fsl-mc node in Linux device tree
from "fsl,dprcr" to "fsl-mc". Print MC version info when
appropriate.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
FSL-LSCH3 platforms can have multiple DDR clocks. LS2085A has one clock for
general DDR controlers, and another clock for DP-DDR. DDR driver needs to
change to support multiple clocks.
Signed-off-by: York Sun <yorksun@freescale.com>
This patch adds the fdt-fixup logic for the clock frequency of the
NS16550A related device tree nodes.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Flushing L3 cache in CCN-504 requries d-cache to be disabled. Using
assembly function to guarantee stack is not used before flushing is
completed. Timeout is needed for simualtor on which CCN-504 is not
implemented. Return value can be checked for timeout situation.
Change bootm.c to disable dcache instead of simply flushing, required
by flushing L3.
Signed-off-by: York Sun <yorksun@freescale.com>
U-Boot should only add "enable-method" and "cpu-release-address"
properties to the "cpu" node of the online cores.
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
According to hardware implementation, a single outer shareable global
coherence group is defined. Inner shareable has not bee enabled.
Signed-off-by: York Sun <yorksun@freescale.com>
This patch ensures that the TZPC (BP147) and TZASC-400 programming
happens for LS2085A SoC only when the desired config flags are
enabled and ensures that the TZPC programming is done to allow Non-secure
(NS) + secure (S) transactions only for DCGF registers.
The TZASC component is not present on LS2085A-Rev1, so the TZASC-400
config flag is turned OFF for now.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
USB doesn't seem to work yet; the controller detects the on-board Hub/
Ethernet device but can't read the descriptors from it. I haven't
investigated yet.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
The bcm2835 and bcm2836 are essentially identical, except:
- The CPU is an ARM1176 v.s. a quad-core Cortex-A7.
- The physical address of many IO controllers has moved.
Rather than introducing a whole new bcm2836 value for $(SOC) or $(ARCH),
update the existing bcm2835 code to handle the minor differences, and
plumb it into the ARMv7 CPU architecture.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Move
arch/arm/cpu/arm926ejs/kirkwood/* -> arch/arm/mach-kirkwood/*
Note:
Perhaps, can we merge arch/arm/mach-kirkwood and
arch/arm/mvebu-common into arch/arm/mach-mvebu, like Linux?
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
The self-bias circuit is used by the bandgap during startup.
Once the bandgap has stabilized, the self-bias circuit should
be disabled for best noise performance of analog blocks.
Also this bit should be disabled before the chip enters STOP mode or
when ever the regular bandgap is disabled.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ranjani Vaidyanathan <Ranjani.Vaidyanathan@freescale.com>
So that the CONFIG_SPL_FEL option is not needed anymore. And the regular
SPL binary, generated by the default u-boot build, is now also bootable
over USB in the FEL mode. The SPL still can boot from the SD card too.
A bunch of system registers need to be saved/restored in order to ensure
that the IRQ handler still works in the BROM FEL code after getting
control back from the SPL. This is done in the sunxi code instead of
abusing ifdefs in 'start.S'.
The decision whether to load the main u-boot binary from the SD card or
return to the FEL code in the BROM is done at runtime.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
[hdegoede@redhat.com: Since we now restore various regs before returning to
the FEL BROM code we can drop the sunxi specific #ifdefs in start.S]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Make sunxi's FEL code fit with the normal U-Boot boot sequence instead of
creating its own. There are some #ifdefs required in start.S. Future work
will hopefully remove these.
This series is available at u-boot-dm, branch sunxi-working.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The link register value can be required on some boards (e.g. FEL mode on
sunxi) so use a branch instruction to jump to save_boot_params() instead
of a branch link.
This requires a branch back to save_boot_params_ret so adjust the users
to deal with this. For exynos just drop the function since it doesn't
do anything.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Move the dram helper functions to a separate C file, rather then having them
as inline helpers in dram.h. This saves 144 bytes in the .text segment for
sun6i builds.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
KS2 ddr3 initialization uses ddr3_size global variable before u-boot
relocation. Even if the variable is not being used after relocation,
writing to it corrupts relocation table.
This patch removes the global ddr3_size variable and uses local one
instead.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
When EMAC is in the boot order, the boot ROM sets OPP50 and the
MAC clock is set to /2. SPL needs to change it to /5 for Ethernet
to generate the correct txclk. This patch sets it correctly.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
The value in SDRAM_REF_CTRL controls the delay time between
the initial rising edge of DDR_RESETn to rising edge of DDR_CKE
(JEDEC specs this as 500us). In order to achieve this, SDRAM_REF_CTRL
should be written with a value corresponding to 500us delay before
starting DDR initialization sequence, and configure proper
value at the end of sequence.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
DDR3 timing and latency paramenters were not configured
correctly for 666MHz. Fixing the timing and latency values
according to Data sheet.
This fixes the random crashes seen on DRA72-evm.
Signed-off-by: Angela Stegmaier <angelabaker@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Since we have src, div and pre-div mask bits defined corresponding
to peripherals, calculation of clock specific to I2C appears
redundant and confusing. Using clk_bit_info struct we can write
calculations generic to all peripherals which makes code easy to
understand and free from peripheral specific exceptions.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
We have assumed and kept mask bits for divider and pre-divider
as 0xf and 0xff, respectively. But these mask bits change from
one peripheral to another, and hence, need to be specified in
accordance with the peripherals.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Replacing SoC and peripheral specific function calls with generic
clock_get_periph_rate calls to get the peripheral clocks.
Also, removing dead code of peripheral and SoC specific function
implementations which was used earlier for fetching peripheral clocks.
This code is not being used anymore because of the introduction
of generic clock_get_periph_rate function.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
exynos5_get_periph_rate function reads incorrect div for
SDMMC2 & 3. It also reads prediv and does division only for
SDMMC0 & 2 when actually various other peripherals need that.
Adding changes to fix these mistakes in periph rate calculation.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
We planned to fetch peripheral rate through one generic API per
peripheral. These generic peripheral functions are in turn
expected to fetch apt values from a function refactored as
per SoC versions. This patch adds support for fetching peripheral
rates for Exynos5420 and Exynos5800.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Moving exynos5420_get_pll_clk function definition up in the
code to keep it together with rest of SoC_get_pll_clk functions.
This makes code more legible and also removes the need of
declaration when called before the position of definition in
code. Also, renaming exynos5420_get_pll_clk to
exynos542x_get_pll_clk because it is being used for both Exynos
5420 and 5800.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Apparently, members of clk_bit_info array do not map correctly
to the members of enum periph_id. This mapping got broken after
we changed periph_id(s) to reflect interrupt number instead of
their position in a sequence. This patch intends to fix above
mentioned issue.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Exynos5420 has different registers with other exynos5 SoCs to control
usb device phy, so need separated function to enable exynos5420 usb
device phy.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The most exynos used the "Ratio + 1" as div value.
And value at register is "Ratio".
So if want to set exact value, it needs to subtract one.
Value at register ("Ratio") = div - 1
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
r8a7794 uses ARM SoC of CA7 base. If we want to use dcache on CA7, we
need to enable SMP bit of Auxiliary Control Register.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
SILK is an entry level development board based on R-Car E2 SoC (R8A7794)
This commit supports the following peripherals:
- SCIF, I2C, Ethernet, QSPI, MMC, USB Host
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Tom Rini <trini@ti.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
When booting in JTAG mode, there is no way to use soft break-points, and
no way of knowing when SPL has finished executing (so the user can issue
a 'halt' command to load u-boot.bin for example)
Add a debug output and simple loop to stop execution at the completion of
the SPL initialisation as a pseudo break-point when booting in JTAG mode
Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
Section 4.1.2 of Freescale Application Note AN4199 describes the
configuration required to operate the mx28 from a 5V source without a
battery.
This patch changes the behaviour of the dropout control of the DC-DC
converter (refer to section 11.12.9 of the mx28 Application Processor
Reference Manual - Document Number: MCIMX28RM, Rev 2, 08/2013) to the
following:
- Always use 4P2 Linear Regulator if CONFIG_SYS_MXS_VDD5V_ONLY is defined
- Switch between 4P2 Linear Regulator and Battery, using whichever has
the highest voltage if CONFIG_SYS_MXS_VDD5V_ONLY isnot set (this is
the same as the pre-patch behaviour)
Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
Signed-off-by: Damien Gotfroi <dgotfroi@greenwatch.be>
It is difficult to track down fail to boot issues in the mxs SPL.
Implement the following to make it easier:
- Add debug outputs to allow tracing of SPL progress in order to track
where failure to boot occurs. DEUBUG and CONFIG_SPL_SERIAL_SUPPORT must
be defined to enable debug output in SPL
- Add TODO comments where it is not clear if the code is doing what it
is meant to be doing, even tough the board boots properly (these comments
refer to existing code, not to any code added by this patch)
Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
Should use AIPS3 configuration address 0x0227C000 to set AIPS3,
not the AIPS3 base address.
Additional, replace AIPS1_BASE_ADDR to AIPS3_ARB_BASE_ADDR to align with
AIPS1 and AIPS2, and resolve the AIPS3_ARB_BASE_ADDR undefine problem.
Signed-off-by: Ye.Li <B37916@freescale.com>
As the at91cap9adk board is removed by commit: b5508344
(ARM: remove broken "at91cap9adk" board), so the at91cap9
code is not used anymore, and also the document for
at91cap9 can not be found on www.atmel.com, so remove the
at91cap9 related code.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
Some SoC need to redirect the saic to aic to make the interrupt to
work, here add a weak function to be replaced by real function.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
This patch adds SPL support to the Marvell Armada-XP. With this addition
the bin_hdr integration is not needed any more. The SPL will first
initialize the serdes/PHY and the call the DDR setup and training code
now integrated into mainline U-Boot.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Luka Perkov <luka.perkov@sartura.hr>
Checking if the pointer is NULL would be easier to know the tail
of the boot_device_table[] array.
For clarification, add the /* sentinel */ comment.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The return value of get_boot_mode_sel() is used as the index of
the boot_device_table[] array. Its type should be "int" rather
than "u32".
Use only the iterator "i" for the loop in do_pinmon().
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
To use I2C controllers on PH1-sLD8, the bit 10 (SCL0/SDA0)
and bit 11 (SCL1/SDA1) of IECTRL register must be set.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
It is true that unused functions are removed from the ELF image
by the compiler's garbage collection but relying on it too much
does not look nice.
Currently, the build is taking more than it should.
Refactor the makefiles to compile only files that are really needed.
CONFIG_SOC_INIT and CONFIG_DRAM_INIT are no longer needed by the
optimization.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Since commit 0365ffcc0b (generic-board: show model name in
board_init_f() too), checkboard() is invoked only when
show_board_info() fails to get the model name from Device Tree.
It never happens because UniPhier SoCs now only work with
CONFIG_OF_CONTROL and all the root nodes of UniPhier device trees
have the "model" property.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Since commit 0365ffcc0b (generic-board: show model name in
board_init_f() too), the support card information has not been
displayed because check_support_card() is invoked only when
show_board_info() fails to get the model name from Device Tree.
This commit adds misc_init_f() function to call check_support_card()
from there.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Now init functions called from board_postclk_init() and dram_init()
are only necessary for SPL.
Move them to spl_board_init() for clean-up.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Currently, I/O pin settings are not necessary for SPL.
The board_early_init_f() seems a suitable place to call pin_init().
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
It turns out that the device_mode_data is rsb specific, rather then slave
specific, so integrate the rsb_set_device_mode() call into rsb_init().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This patch adds basic constructs in the ARMv8 u-boot code
to handle and apply Cortex-A57 specific erratas.
As and example, the framework showcases how erratas 833069, 826974
and 828024 can be handled and applied.
Later on this framework can be extended to include other
erratas.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
