The arm64 exception handling code is quite big, mostly due to
architectural alignment requirements. Each exception entry spans 32
instructions, which sounds generous, but is too small to fit all of the
save/branch/restore code in there. So at the moment we use only four
instructions, branching into shared save and restore routines.
To not leave the space for those remaining 28 instructions wasted, let's
split the save and restore routines and stuff them into the gaps.
This saves about 250 bytes of code, which is helpful for those tight
SPLs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Highlights this time:
- Many small fixes to improve spec compatibility (found by SCT)
- Almost enough to run with sandbox target
- GetTime() improvements
- Enable EFI_LOADER and HYP entry on ARMv7 with NONSEC=y
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=ePTT
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-07-25
Highlights this time:
- Many small fixes to improve spec compatibility (found by SCT)
- Almost enough to run with sandbox target
- GetTime() improvements
- Enable EFI_LOADER and HYP entry on ARMv7 with NONSEC=y
Another round of sorting Kconfig entries aplhabetically.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
The include/phy.h will start including dm.h, which pulls in
linux/compat.h after the attempted redefinition in
arch/arm/include/asm/armv8/mmu.h, so move this include to allow
redefinition.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
A new defconfig is introduced to support SPL boot from QSPI NOR
flash. This is to support falcon mode for faster booting into
Linux.
Signed-off-by: York Sun <york.sun@nxp.com>
Remove the old implementation in order to enable DM for sata.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Enable I-cache for SPL boot to boost performance. Earlier MMU was
enabled only for LS2080A and has since been dropped by commit
f539c8a4a7 ("armv8: ls2080a: Drop early MMU for SPL build").
Signed-off-by: York Sun <york.sun@nxp.com>
Some times gcc may generate data that is then used within code that may
be part of an efi runtime section. That data could be jump tables,
constants or strings.
In order to make sure we catch these, we need to ensure that gcc emits
them into a section that we can relocate together with all the other
efi runtime bits. This only works if the -ffunction-sections and
-fdata-sections flags are passed and the efi runtime functions are
in a section that starts with ".text".
Up to now we had all efi runtime bits in sections that did not
interfere with the normal section naming scheme, but this forces
us to do so. Hence we need to move the efi_loader text/data/rodata
sections before the global *(.text*) catch-all section.
With this patch in place, we should hopefully have an easier time
to extend the efi runtime functionality in the future.
Signed-off-by: Alexander Graf <agraf@suse.de>
[agraf: Fix x86_64 breakage]
The Allwinner A64 SoCs suffers from an arch timer implementation erratum,
where sometimes the lower 11 bits of the counter value erroneously
become all 0's or all 1's [1]. This leads to sudden jumps, both forwards and
backwards, with the latter one often showing weird behaviour.
Port the workaround proposed for Linux to U-Boot and activate it for all
A64 boards.
This fixes crashes when accessing MMC devices (SD cards), caused by a
recent change to actually use the counter value for timeout checks.
Fixes: 5ff8e54888 ("sunxi: improve throughput
in the sunxi_mmc driver")
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2018-May/576886.html
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Tested-by: Guillaume Gardet <guillaume.gardet@free.fr>
At the moment we have the workaround for the Freescale arch timer
erratum A-008585 merged into the generic timer_read_counter() routine.
Split those two up, so that we can add other errata workaround more
easily. Also add an explaining comment on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Tested-by: Guillaume Gardet <guillaume.gardet@free.fr>
cpu_cmd() is reading cpu number via simple_strtoul() which is always
unsigned type.
Platform code implementations are not expecting that nr can be negative
and there is not checking in the code for that too.
This patch is using u32 type for cpu number to make sure that platform
code get proper value range.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There should be return value check from zynqmp_mmio_read() in
zynqmp_mmio_rawwrite() to make sure that errors are propagated properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We currently handle the UEFI runtime reset / power off case handling via
a switch statement. Compilers (gcc in my case) may opt to handle these via
jump tables which they may conveniently put into .rodata which is not part
of the runtime section, so it will be unreachable when executed.
Fix this by just converting the switch statement into an if/else statement.
It produces smaller code that is faster and also correct because we no
longer refer .rodata from efi runtime code.
Reported-by: Andreas Färber <aferber@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
FRWY-LS1012A belongs to LS1012A family with features 2 1G SGMII PFE
MAC, Micro SD, USB 3.0, DDR, QuadSPI, Audio, UART.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
[yorks: rebase and fix SPDX tag]
[yorks: fix board/freescale/ls1012afrdm/Kconfig]
Reviewed-by: York Sun <york.sun@nxp.com>
PPA firmware and header address may vary depending upon different
boards, configure ppa firmware and header address in board specific
Kconfig.
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Existing EEMI version is to as 1.0 (available from xilinx v2018.1
version). Update required API version to match with EEMI API version.
New PMUFW version is required for operations with programmable logic.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP emulation platforms are no longer tested and supported that's why
remove macros and code around.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
microblaze:
- Align defconfig
zynq:
- Rework fpga initialization and cpuinfo handling
zynqmp:
- Add ZynqMP R5 support
- Wire and enable watchdog on zcu100-revC
- Setup MMU map for DDR at run time
- Show board info based on DT and cleanup IDENT_STRING
zynqmp tools:
- Add read partition support
- Add initial support for Xilinx bif format for boot.bin generation
mmc:
- Fix get_timer usage on 64bit cpus
- Add support for SD3.0 UHS mode
nand-zynq:
- Add support for 16bit buswidth
- Use address cycles from onfi params
scsi:
- convert ceva sata to UCLASS_AHCI
timer:
- Add Cadence TTC for ZynqMP r5
watchdog:
- Minor cadence driver cleanup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlr1ldMACgkQykllyylKDCHioACghoJw6+NqsZXl8zGWRP38yZ5K
mvgAnihfOQq125mpKPZmcc5yt6wVwYIU
=8ji9
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2018.07' of git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2018.07
microblaze:
- Align defconfig
zynq:
- Rework fpga initialization and cpuinfo handling
zynqmp:
- Add ZynqMP R5 support
- Wire and enable watchdog on zcu100-revC
- Setup MMU map for DDR at run time
- Show board info based on DT and cleanup IDENT_STRING
zynqmp tools:
- Add read partition support
- Add initial support for Xilinx bif format for boot.bin generation
mmc:
- Fix get_timer usage on 64bit cpus
- Add support for SD3.0 UHS mode
nand-zynq:
- Add support for 16bit buswidth
- Use address cycles from onfi params
scsi:
- convert ceva sata to UCLASS_AHCI
timer:
- Add Cadence TTC for ZynqMP r5
watchdog:
- Minor cadence driver cleanup
This patch fills the MMU map for DDR at run time based on information read
from Device Tree or automatically detected from static configuration.
The patch is needed because for systems which has for example 1GB of memory
but MMU map is 2GB there could be spurious accesses which was seen in past
when mapping is not fitting with actual memory installed.
Signed-off-by: Nitin Jain <nitin.jain@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mask HRESET_B after cleared the the RCW_SRC, because in the workaround
we override the RCW_SRC and if HRESET_B is issued after the override
then SoC cannot find valid RCW as the RCW_SRC was overwritten and
result in hang. So we need to mask HRESET_B in case user asserts it,
and the PORESET_B should be asserted which leads to resampling of
cfg_rcw_src pins and loading of correct RCW_SRC.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Enable support for multiple loadable images in SEC firmware FIT image.
Also add example "sec_firmware_ppa.its" file.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
JR3 was getting removed from device tree only if random number
generation was successful. However, if SEC firmware is present,
JR3 should be removed from device tree node irrespective of the
random seed generation as SEC firmware reserves it for it's use.
Not removing it in case of random number generation failure causes
the kernel to crash.
Random number generation was being called twice. This is not
required. If SEC firmware is running, SIP call can be made to the SEC
firmware to get the random number. This call itself would return
failure if function is not supported. Duplicate calling of random
number generation function has been removed.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TZASC controller configurations are similar. Put them in a macro and
avoid code duplication.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
SYS_ARCH_TIMER guards the usage of the ARM Generic Timer (aka arch
timer) in U-Boot.
At the moment it is mandatory for ARMv8 and used by a few ARMv7 boards.
Add a proper Kconfig symbol to express this dependency properly,
allowing certain board configuration to later disable arch timer in case
there are any problems with it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[tuomas: rebase + fix conflicts and resync with moveconfig & use select]
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
The default of DISTRO_DEFAULTS is messy. Using the 'imply' keyword
is equivalent and cleaner.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
EFI_RESET_PLATFORM_SPECIFIC is one of the values that can be used for the
EFI service ResetSystem. The missing definition is added. The value has to
handled in efi_reset_system().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
efi_reset_system_init provides the architecture or board specific
initialization of the EFI subsystem. Errors should be caught and
signalled by a return code.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
NXP layerscape platforms like ls1088a, ls2088a
uses MXC I2C Controller.
-Remove dependency of MX6 for the same.
Update related configs to use Kconfig file.
-Add SYS_I2C_MXC_I2C1,_I2C2,_I2C3,_I2C4 in Kconfig
-Add CONFIG_SYS_MXC_I2C1_SPEED,_I2C2_,_I2C3_,_I2C4_ in Kconfig
-Add CONFIG_SYS_MXC_I2C1_SLAVE,_I2C2_,_I2C3_,_I2C4_ in Kconfig
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
As of now newer pmufw is keeping old interfaces. That's why permit
u-boot to run on newer version. Recommended version will be setup later.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
1. Set AWCACHE0 attribute of PFE DDR and HDBUS master interfaces
to bufferable.
2. Set RD/WR QoS for PFE DDR and HDBUS AXI master interfaces.
3. Disable ECC detection for PFE.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.
This commit moves the header code:
include/libfdt.h -> include/linux/libfdt.h
include/libfdt_env.h -> include/linux/libfdt_env.h
and replaces include directives:
#include <libfdt.h> -> #include <linux/libfdt.h>
#include <libfdt_env.h> -> #include <linux/libfdt_env.h>
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch added Kconfig support for CONFIG_ZYNQ_SDHCI_MAX_FREQ
and enabled it in respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove dependency of SYS_HAS_SERDES for Layerscape Chasis 2 and
Layerscape Chasis 3.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The goal of this patch is to clean up the code related to choosing SPL
MMC boot mode.
The spl_boot_mode() now is called only in spl_mmc_load_image() function,
which is only compiled in if CONFIG_SPL_MMC_SUPPORT is enabled.
To achieve the goal, all per mach/arch implementations eligible for
unification has been replaced with one __weak implementation.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com> (For ZynqMP)
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlpxesoACgkQykllyylKDCFwngCfZfk2S+c9uJCLh1drA7a+J4Ch
G+MAnA/iRu6/Ihd5UMe4tMK8BU51h0GQ
=Ylul
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2018.03' of git://git.denx.de/u-boot-microblaze
Xilinx changes for v2018.03
- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes
There is no JTAG symbol in the "Boot mode" choice. JTAG_MODE was
probably intended.
No functional changes. Kconfig choices fall back on using the first
(visible) symbol in the choice as the default if the default symbol is
not visible.
Discovered in Kconfiglib (https://github.com/ulfalizer/Kconfiglib),
which prints the following warning:
warning: the default selection JTAG (undefined) of <choice> (defined at arch/arm/cpu/armv8/zynqmp/Kconfig:107) is not contained in the choice
I've added a corresponding warning to the C tools too, which is
currently in linux-next: https://patchwork.kernel.org/patch/9983667/
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move generic functions to common location psu_spl_init.c. Function
declarations are added to private header.
These changes are done in connection to the fact that still files from
HDF can be copied over and compilation should pass.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DDR less systems are possible for configuration like mini qspi
and making DDR region as normal memory may cause speculative
access which results u-boot hang if DDR is absent. So, this
patch fixes the issue by not making DDR memory region
entry into MMU table.
Future solution is to prepare MMU table per memory node in dts instead
of hard code DDR addresses.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
psu_init() returns int which wasn't declared and checked.
The patch is fixing function declarations and code to handle return
values properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Set the 8GB PCIe High area as device memory.
Also extend the DDR High area to cover the full 32GB range.
Signed-off-by: Anders Hedlund <anders.j.hedlund@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Adds a VID specific API in init_sequence_f and spl code flow
namely init_func_vid which is required to adjust core voltage.
VID specific code is required in spl, hence moving flag CONFIG_VID
out of spl flags.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Adds SERDES voltage and reset SERDES lanes API and makes
enable/disable DDR controller support 0.9V API common.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The DT spec demands a unit-address in a node name to match the "reg"
property in that node. Newer dtc versions will throw warnings if this is
not the case.
Remove the unit address from the config node name when U-Boot deals with
secure firmware FIT images.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The DT spec demands a unit-address in a node name to match the "reg"
property in that node. Newer dtc versions will throw warnings if this is
not the case.
Fix all occurences in various documentation files where this was not
observed, to not give bad examples to the reader.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The SP805-WDT module on LS1088A requires configuration of PMU's
PCTBENR register to enable watchdog counter decrement and reset
signal generation. The watchdog clock needs to be enabled first.
Signed-off-by: Zhang Ying-22455 <ying.zhang22455@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1012A-2G5RDB belongs to LS1012A family with features 2 2.5G SGMII
PFE MAC, SATA, USB 2.0/3.0, WiFi DDR, eMMC, QuadSPI, UART.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Align boards belonging to LS1012A, LS2080A SoC at one place.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Allow placing a Linux kernel image header at the start of the U-Boot
binary. This is useful since the image header reports the amount of memory
(BSS and similar) that U-Boot needs to use, but that isn't part of the
binary size. This can be used by the code that loads U-Boot into memory to
determine where to load U-Boot, based on other users of memory.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Compile-off mp.c and libfdt.c in case of SPL build. SPL size reduces
by approx 2k.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
855873: An eviction might overtake a cache clean operation
Workaround: The erratum can be avoided by upgrading cache clean by
address operations to cache clean and invalidate operations. For
Cortex-A53 r0p3 and later release, this can be achieved by setting
CPUACTLR.ENDCCASCI to 1.
This patch is to implement the workaround for this erratum.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds changes necessary to move functionality present in
PowerPC folders with ARM architectures that have DPAA1 QBMan hardware
- Create new board/freescale/common/fsl_portals.c to house shared
device tree fixups for DPAA1 devices with ARM and PowerPC cores
- Add new header file to top includes directory to allow files in
both architectures to grab the function prototypes
- Port inhibit_portals() from PowerPC to ARM. This function is used in
setup to disable interrupts on all QMan and BMan portals. It is
needed because the interrupts are enabled by default for all portals
including unused/uninitialised portals. When the kernel attempts to
go to deep sleep the unused portals prevent it from doing so
Signed-off-by: Ahmed Mansour <ahmed.mansour@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Sata registers PP2C and PP3C are used to control the configuration
of the PHY control OOB timing for the COMINIT/COMWAKE parameters
respectively. Calculate those parameters from port clock frequency.
Overwrite those registers with calculated values to get better OOB
timing.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Freescale (NXP) boards have lots of defconfig files per board.
I used "imply PANIC_HANG" for them.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Using "cpu_pos_mask()" function to detect the real online cpus,
and discard the needless cpu nodes on kernel dts.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Check LS1043A/LS2080a by device ID without using personality ID to
determine revision number. This check applies to all various
personalities of the same SoC family.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Validates PPA, MC, DPC, Bootscript, DPL and Kernel images in ESBC
phase using esbc_validate command.
Enable validation of boot.scr script prior to its execution dependent
on "secureboot" flag in environment
Add header address for PPA to be validated during ESBC phase for
LS1088A platform based on LAyerscape Chasis 3.
Moves sec_init prior to ppa_init as for validation of PPA sec must
be initialised before the PPA is initialised.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This is suplement for patch which handle below errata:
A-009007, A-009008, A-008997, A-009798
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Instruction prefetch feature is by default enabled during core
release. This patch add support of disabling instruction prefetch
by setting core mask in PPA. Here each core mask bit represents a
core and prefetch is disabled at the time of core release.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
To page mapping the lowest 2 bits needs to be 0x3.
If not fix this, the final lowest 3 bits for page mapping is 0x1
which is marked as reserved.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In the moment our exception entry code needs 34 instructions, so we
can't use put it directly into the table entry, which offers "only"
32 instructions there. Right now we just put an unconditional branch
there, then use a macro to place the 34 instructions *per entry* after
that. That effectivly doubles the size of our exception table, which
is quite a waste, given that we use it mostly for debugging purposes.
Since the register saving part is actually identical, let's just convert
that macro into a function, and "bl" into it directly from the exception
slot, of course after having saved at least the original LR.
This saves us about 950 bytes of code, which is quite a relief for some
tight SPLs, in particular the 64-bit Allwinner ones.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This modifies default value of config DEFINE_TCM_OCM_MMAP
to yes if CONFIG_MP is defined MP supports needs OCM and TCM
part of memory map.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch is adding external pmufw "Platform Management Unit firmware"
to boot.bin image. Boot.bin is a Xilinx format which bootrom is capable
to read and boot the system. pmufw is copied to the header data section
follows by u-boot-spl.bin. pmufw is consumed by PMU unit (Microblaze)
and SPL runs on a53-0.
This is generated command line when PMUFW_INIT_FILE is setup.
./tools/mkimage -T zynqmpimage -R ./"" -n
./"board/xilinx/zynqmp/pmufw.bin" -d spl/u-boot-spl.bin spl/boot.bin
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch provides a Kconfig option to use specified
memory for MMU table using reserve_mmu platform specific
routine. Here we used TCM space for MMU table.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch corrects the R5 release sequence by adding the
below steps.
1. Flush dcache to ensure that image loaded into memory.
2. Keep R5 reset just to ensure R5 in reset.
3. Disable caches before accessing TCM as with out this
A53 can do speculative and may result in ECC failures
if TCM's are not initialized. So, it is always better
to disable dcaches before accessing TCM and enable back.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reported-by: John Linn <linnj@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In
if (a || b)
else if (!a)
the constraint (!a) is always true if else is reached and
can be removed.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This is required in the case where U-Boot is typically loaded and run at
a particular address, but for some reason the RAM at that location is not
available, e.g. due to memory fragmentation loading other boot binaries or
firmware, splitting an SMP complex between various different OSs without
using e.g. the EL2 second-stage page tables to hide the memory asignments,
or due to known ECC failures.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Value provided in MC_MEM_SIZE_ENV_VAR is in hex. Use 16 as base
in simple_strtoul.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Enable support for loadables in SEC firmware FIT image. Currently
support is added for single loadable image.
Brief description of implementation:
Add two more address pointers (loadable_h, loadable_l) as arguments to
sec_firmware_init() api.
Create new api: sec_firmware_checks_copy_loadable() to check if loadables
node is present in SEC firmware FIT image. If present, verify loadable
image and copies it to secure DDR memory.
Populate address pointers with secure DDR memory addresses where loadable
is copied.
Example use-case could be trusted OS (tee.bin) as loadables node in SEC
firmware FIT image.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Use Kconfig to select QE-HDLC and USB pin-mux.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add jump_to_image_linux() for arm64. Add "noreturn" flag to
armv8_switch_to_el2(). Add hooks to fsl-layerscape to enable falcon
boot.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Tested-by: Łukasz Majewski <lukma@denx.de>
gd->ram_size is reduced in this function to reserve secure memory.
Avoid running this function again to further reduce memory size.
This fixes issue for SPL boot with PPA image loaded in which case
secure memory is incorrectly allocated due to repeated calling.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit 15eb1d43bf ("spl: reorder the assignment of board info to
global data") intended to move assignment of board info earlier,
into board_init_r(). However, function preload_console_init() is
called either from spl_board_init() or from board_init_f(). For the
latter case, the board info assignment is much earlier than proposed
board_init_r(). Create a new function to fill gd->bd and call this
function when needed.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Ravi Babu <ravibabu@ti.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This change is required due to trusted OS (OP-TEE) not being position
independent code, it requires compile time fixed base address.
To take care of this it is assumed that all layerscape armv8 platforms
has minimum 2G ddr in first region. So we can have fixed address
space (66 MB -> (2MB for PPA + 64MB for trusted OS)) allocated from
top of first 2G ddr region and compile trusted OS with this fixed
base address.
But one exception here is ls1012 where we have only 1G (rdb) or 512M
(frdm) ddr memory. For those we can have different fixed compile time
base addresses for trusted OS.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Rx Compliance tests may fail intermittently at high jitter
frequencies using default register values.
Program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
It is not necessary for every SoC to have 2 SATA controller.
So put SATA1, SATA2 code under respective defines.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
All these places seem to inherit the codes from the MMC driver where
a FIXME was put in the comment. However the correct operation after
read should be cache invalidate, not flush.
The underlying drivers should be responsible for the cache operation.
Remove these codes completely.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: York Sun <york.sun@nxp.com>
CCN-504 HPF registers were believed to be accessible only from EL3.
However, recent tests proved otherwise. Remove checking for exception
level to re-enable L3 cache flushing for all levels.
Signed-off-by: York Sun <york.sun@nxp.com>
Tested-by: Zhao Qiang <qiang.zhao@nxp.com>
In case high region memory doesn't have enough space for Management
Complex (MC), the return value should indicate a failure so the
caller can handle it accordingly.
Signed-off-by: York Sun <york.sun@nxp.com>
Reported-by: Ebony Zhu <ebony.zhu@nxp.com>
Rx Compliance tests may fail intermittently at high
jitter frequencies using default register values.
Program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.bhagat@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
Low Frequency Periodic Signaling(LFPS) Peak-to-Peak Differential
Output Voltage Test Compliance fails using default transmitter
settings
Change config of transmitter signal swings by setting register
PCSTXSWINGFULL to 0x47 to pass compliance tests.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
The default setting for USB High Speed Squelch Threshold results
in a threshold close to or lower than 100mV. This leads to Receiver
Compliance test failure for a 100mV threshold.
Shift the threshold from ~100mV towards ~130mV by setting SQRXTUNE
to 0x0 to pass USB High Speed Receiver Sensitivity Compliance test.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
USB High Speed (HS) EYE Height Adjustment
USB HS speed eye diagram fails with the default value at
many corners, particularly at a high temperature
Optimal eye at TXREFTUNE value to 0x9 is observed, change
set the same value.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds support for RGMII protocol
NXP's LDPAA2 support RGMII protocol. LS1088A is the
first Soc supporting both RGMII and SGMII.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch add support of LS1088AQDS platform.
The LS1088A QorIQTM Development System (QDS) is a high-performance
computing, evaluation, and development platform that supports the
LS1088A QorIQ Architecture processor.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1088A is an ARMv8 implementation. The LS1088ARDB is an evaluatoin
platform that supports the LS1088A family SoCs. This patch add basic
support of the platform.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
[YS: Disabled NAND in board header file]
Reviewed-by: York Sun <york.sun@nxp.com>
WIP: disable NAND for LS1088ARDB
According current code base, CONFIG_LS1012A should be
CONFIG_ARCH_LS1012A, or function fsl_fdt_disable(blob) will be
wrongly called to disable all dwc3 USB nodes on LS1012A, which
cause Linux USB function stop working at all.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2080 family has CCN-504 cache coherent interconnet. Other SoCs
in LSCH3 family may have differnt interconnect.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[YS: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Adds header address for PPA to be validated during ESBC phase for
ARCH_LS2088 and QSPI_BOOT. Moves sec_init prior to ppa_init(). It
must be initialized before the PPA.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[YS: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Unify memory map for Layerscape based platforms. This patch includes
changes in bootscript, bootscript header and PPA header addresses
change as per unified memory map.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Tested-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
CoreLink Cache Coherent Interconnect (CCI) provides full cache
coherency between two clusters of multi-core CPUs and I/O coherency
for devices and I/O masters.
This patch add new config option SYS_FSL_HAS_CCI400 and moves
existing register space definaton of CCI-400 bus to fsl_immap to be
shared. CONFIG_SYS_CCI400_ADDR is replaced with SYS_CCI400_OFFSET
in Kconfig.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[YS: revised commit message, squashed patches for armv8 and armv7]
Reviewed-by: York Sun <york.sun@nxp.com>
kASLR support in kernel requires a random number to be passed via
chosen/kaslr-seed propert. sec_firmware generates this random seed
which can then be passed in the device tree node.
sec_firmware reserves JR3 for it's own usage. Node for JR3 is
removed from device-tree.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
With SPL_LDSCRIPT moved to Kconfig (and this being a 'string' config
node), all the lingering definitions in header files will cause
warnings/errors due to the redefinition of the configuration item.
As we don't want to pollute the defconfig files (and values should
usually be identical for entire architectures), the defaults are moved
into Kconfig. Kconfig will always pick the first default that
matches, so please keep these values at the end of each file (to allow
any board-specific Kconfig, which will be included earlier) to
override with an unconditional default setting.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To fully support DM timer in SPL and TPL, we need a few things cleaned
up and normalised:
- inclusion of the uclass and drivers should be an all-or-nothing
decision for each stage and under control of $(SPL_TPL_)TIMER
instead of having the two-level configuration with TIMER and
$(SPL_TPL_)TIMER_SUPPORT
- when $(SPL_TPL_)TIMER is enabled, the ARMv8 generic timer code can
not be compiled in
This normalises configuration to $(SPL_TPL_)TIMER and moves the config
options to drivers/timer/Kconfig (and cleans up the collateral damage
to some defconfigs that had SPL_TIMER_SUPPORT enabled).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
TPL builds today don't need to call into firmware or set up the MMU
(if this changes, it should be controlled through a config option
whether to include this or not), but include the needed support code
for this anyway. By moving these unused low-level functions into
seperate function-sections, the linker can garbage-collect the unused
sections.
Note that (if DM support is enabled), there will be a call to the
cache-flushing code from alloc_priv(...) in drivers/core/device.c.
This then add 52 bytes of binary size (an increase from 20589 to 20641
bytes) compared to completely removing this code.
Even for a feature-rich TPL (including DM support as for the RK3368),
this equates to a size difference of significantly more than 10% in
TPL binary size.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_CMD_PCI
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
It is derived from Platform clock instead of Platform PLL frequency.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
There is a need to include psu_init also in mini u-boot configuration
that's why handle psu_init via Kconfig property.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
For some mini platforms there could be a need to include psu_init.
That's why move it to board file instead of spl only file.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch removes ifdef around mmio read and write rotuines
and make them a single routine by checking the current el.
This patch helps to remove ifdef around invoke_smc as well.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
TCM on ZynqMP needs to be intialized in a sequence
and this patch provides a global routine to perform
this as per requirement.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch provides an option to include OCM and TCM memory
into MMU table with corresponding memory attributes.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The duplicate definitions for IH_ARCH_ARM and IH_ARCH_ARM64 are removed.
The definitions in <image.h> are used.
According to this modification, the comparison between os arch and cpu
arch is done in C programming instead of ASM programming.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As part of preparation for nand DM conversion the new API has been
introduced to remove direct access to nand_info array. So, use it here
instead of accessing to nand_info array directly.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
The 'mode' parameter is actually a flag to determine whether to display
a list of devices found during the scan. Rename it to reflect this, add a
function comment and adjust callers to use a boolean.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This actually works on snapdragon.. not sure why we weren't using it.
Fixes reboot/poweroff when using UEFI.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
If PMUFW version is not v0.3 then panic.
ZynqMP switch to CCF based clock driver which requires
PMUFW to be present at certain version.
This patch ensure that you use correct and tested PMUFW
binary.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define routines of mmio write and read functionalities
for zynqmp platform.
Also do not call SMC from SPL because SPL is running before ATF in EL3
that's why SMCs can't be called because there is nothing to call.
zynqmp_mmio*() are doing direct read/write accesses and this patch does
the same. PMUFW is up and running at this time and there is a way to talk
to pmufw via IPI but there is no reason to implement IPI stuff in SPL if
we need just simple read for getting clock driver to work.
Also make invoke_smc as global so that it can be reused in
multile places where ever possible.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Silicon v1 didn't support SD boot mode with level shifter.
Because system can't boot any error message is not shown
that's why comment is just a record if someone tries to debug it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The boot_device argument to spl_boot_mode was massively added without
actually modifying the existing functions.
This commit actually makes use of the handed value, which is the same.
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When enabling both SDHCI controllers, spl_mmc.c would actually choose
device sdhci0 even if booted from sdhci1 (boot_device). This is because
spl_mmc_get_device_index(boot_device) expects BOOT_DEVICE_MMC2[_2] in
order to return index 1 instead of 0.
The #if defined(...) statement is copied from board/xilinx/zynqmp/zynqmp.c
So the key to properly enabling both controllers as boot sources is
defining both CONFIG_ZYNQ_SDHCI0 and CONFIG_ZYNQ_SDHCI1 in your board's
include/configs/*.h.
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mark explicitly bss sections to not be loaded at
run time.
The similar patch was done in past by:
"Fix linker scripts: add NOLOAD atribute to .bss/.sbss sections"
(sha1: 64134f0112)
The problem is related to latest toolchain added to Xilinx
v2017.1 design tools where jtag loader is trying to access
ununitialized memory.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for calling poweroff in case of psci is wired.
Based on the same solution as is used for reset.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Move all logic in to fwcall.c as other ARMs implement poweroff
via PMIC]
Signed-off-by: Tom Rini <trini@konsulko.com>
The declarations should not be in common.h. Move them to the arch-specific
headers.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Fixup thinko defined(FSL_LSCH3) -> defined(CONFIG_FSL_LSCH3)]
Signed-off-by: Tom Rini <trini@konsulko.com>
Loading PPA in SPL puts the rest of U-Boot (including RAM version
loaded later) in EL2 with MMU and cache enabled. Once PPA is loaded,
PSCI is available.
Signed-off-by: York Sun <york.sun@nxp.com>
When U-Boot boots from EL2, skip some lowlevel init code requiring
EL3, including CCI-400/CCN-504, trust zone, GIC, etc. These
initialization tasks are carried out before U-Boot runs. This applies
to the RAM version image used for SPL boot if PPA is loaded first.
Signed-off-by: York Sun <york.sun@nxp.com>
Add CONFIG_NAND_BOOT config flag to organise
NAND_BOOT specific code in config flag like
-nand-boot specfic errata errata_rcw_src()
-CONFIG_SYS_NAND_U_BOOT_DST,etc
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
These two functions have an of_ prefix which conflicts with naming used
in of_addr. Rename them:
fdt_read_number
fdt_support_bus_default_count_cells
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch is to adjust the memory mapping for FLash/SD card on
LS1043AQDS and LS1043ARDB, such as PPA firmware load address, FMAN
firmware load address, QE firmware load address, U-Boot start address
on serial flash and environment address.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2081ARDB board is similar to LS2080ARDB board with few differences
It hosts LS2081A SoC
Default boot source is QSPI-boot
It does not have IFC interface
RTC and QSPI flash device are different
It provides QIXIS access via I2C
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The QorIQ LS2081A SoC has eight 64-bit ARM v8 Cortex A72 cores and
is built on layerscape architecture. It is 40-pin derivative of
LS2084A (non-AIOP personality of LS2088A). So feature-wise it is
same as LS2084A. LS2041A is a 4-core personality of LS2081A.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QSPI-boot is supported on LS2088ARDB RevF board with LS2088A SoC.
LS2088ARDB RevF Board has limitation that QIXIS can not be accessed.
CONFIG_FSL_QIXIS is not enabled.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The SMPEN bit is located in the cpuectlr_el1 register and not the
cpuactlr_el1 register. Adjust the comment accordingly and also fix
a spelling error.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
CC: Mingkai Hu <mingkai.hu@nxp.com>
CC: Gong Qianyu <Qianyu.Gong@nxp.com>
CC: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
CC: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
CC: York Sun <york.sun@nxp.com>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>
At present there is not operation to invalidate a cache range. This seems
to be needed to fill out the cache operations. Add an implementation based
on the flush operation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
PSCI can be used on both multiple and single core socs. Current
implementation only allows PSCI to work on multiple core socs.
This patch removes this restriction so that PSCI can work on
single core socs as well.
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add Kconfig option to support loading PPA header from eMMC/SD and
NAND Flash.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Tested-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Imports ARM SMC Calling Convention code from Linux 4.11-rc6.
The files have been copied as follows:
[Linux] [U-Boot]
arch/arm/kernel/smccc-call.S -> arch/arm/cpu/armv7/smccc-call.S
arch/arm64/kernel/smccc-call.S -> arch/arm/cpu/armv8/smccc-call.S
arch/arm/include/asm/opcodes* -> arch/arm/include/asm/opcodes*
include/linux/arm-smccc.h -> include/linux/arm-smccc.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Current sysclk fixing would fix all clocks with 'fixed-clock' compatible.
This patch is to fix sysclk by path to avoid any incorrect fixing.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Number of TZASC instances may vary across NXP SoCs.
So put TZASC configuration under instance specific defines.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
- Add SD secure boot target for ls1043ardb.
- Implement FSL_LSCH2 specific spl_board_init() to setup CAAM stream
ID and corresponding stream ID in SMMU.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size as
header is appended to u-boot image. So header will also be copied
from SD to DDR.
- CONFIG_MAX_SPL_SIZE is limited to 90KB. SPL is copied to OCRAM
(128K) where 32K are reserved for use by boot ROM and 6K for secure
boto header.
- Error messages during SPL boot are limited to error code numbers
instead of strings to reduce the size of SPL image.
Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Define bootscript and its header addresses for QSPI target
Also add PPA header address in Kconfig
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The header address of PPA defined in Kconfig.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This function name shadows a global name but is in fact different. This
is very confusing. Rename it to help with the following refactoring.
Signed-off-by: Simon Glass <sjg@chromium.org>
spl_mmc.c calls mmc_initialize(). This symbol is provided in
drivers/mmc/mmc.c when CONFIG_GENERIC_MMC is enabled.
The sunxi Kconfig case is an oddball because it redefines
SPL_MMC_SUPPORT.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
[trini: Update arch/arm/cpu/armv8/zynqmp/Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
By making dram_init_banksize() return an error code we can drop the
wrapper. Adjust this and clean up all implementations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
At present we cannot use this function as an init sequence call without a
wrapper, since it returns the RAM size. Adjust it to set the RAM size in
global_data instead, and return 0 on success.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
It looks like only cm5200 and tqm8xx use this feature, so we don't really
need it in generic code. Drop it and have the users access gd->board_type
directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
USB requires 100MHz clock. On LS1012A, a dedicated 100MHz is provided
instead of SYSCLK (125MHz). Skipping checking SYSCLK for FDT fixup.
Signed-off-by: Yingxi Yu <yingxi.yu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The LS2088A series SoCs has different physical memory map address and
CCSR registers address against LS2080A series SoCs.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This i2c errata only applies to LS2080A and its variants, namely
LS2080A, LS2085A and LS2088A.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
SerDes information is not necessary to be present in RCWSR29 register.
It may vary from SoC to SoC.
So Avoid RCWSR28 register hard-coding.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
MAC number used per QSGMII is not fixed. It may wary from SoC to SoC.
So move QSGMII wriop_init_dpmac() to SoC file.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Erratum A009635 is valid only for LS2080A SoC and its
personality. Add SoC svr check.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Read DMA operations causes CRC error on armv8 chassis 2 platforms
due to the erratum A-010635.
In order to support sata on these platforms, ECC needs to be disabled.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In early MMU table, DDR has to be mapped as device memory to avoid
speculative access. After DDR is initialized, it needs to be updated
to normal memory to allow code execution. To simplify the code,
dram_init() is moved into a common file as a weak function.
Signed-off-by: York Sun <york.sun@nxp.com>
Function mmu_change_region_attr() is added to change existing mapping
with updated PXN, UXN and memory type. This is a break-before-make
process during which the mapping becomes fault (invalid) before final
attributres are set.
Signed-off-by: York Sun <york.sun@nxp.com>
Early MMU improves performance especially on emulators. However, the
early MMU is left enabled after the first stage of SPL boot. Instead
of flushing D-cache and dealing with re-enabling MMU for the second
stage U-Boot, disabling it for SPL build simplifies the process. The
performance penalty is unnoticeable on the real hardware. As of now,
SPL boot is not supported by existing emulators. So this should have
no impact on emulators.
Signed-off-by: York Sun <york.sun@nxp.com>
This patch follows the break-before-make process when making changes
to MMU table. MMU is disabled before changing TTBR to avoid any
potential race condition.
Signed-off-by: York Sun <york.sun@nxp.com>
Update mapping with actual DDR size. Non-existing memory should not
be mapped as "normal" memory to avoid speculative access.
Signed-off-by: York Sun <york.sun@nxp.com>
For ARMv8 Layerscape SoCs, secure memory and MC memorey are reserved
at the end of DDR. DDR is spit into two or three banks. This patch
reverts commit aabd7ddb and simplifies the calculation of reserved
memory, and moves the code into common SoC file. Secure memory is
carved out first. DDR bank size is reduced. Reserved memory is then
allocated on the top of available memory. U-Boot still has access
to reserved memory as data transferring is needed. Device tree is
fixed with reduced memory size to hide the reserved memory from OS.
The same region is reserved for efi_loader.
Signed-off-by: York Sun <york.sun@nxp.com>
This moves all of the current ARM errata from various header files and in to
Kconfig. This allows for a minor amount of cleanup as we had some instances
where both a general common header file was enabling errata as well as the
board config. We now just select these once at the higher level in Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
IFC IP clock is always a constant divisor of platform clock
pre-defined per SoC. Clock control register (CCR) used in
current implementation governs IFC IP output clock.
Update sys_info->freq_localbus to represent IFC input clock with
value constant divisor of platform clock.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This feature seems to be sometimes misunderstood. The intention is:
[1] Bring the slaves into the U-Boot proper image, not SPL (unless
you have a special reason to do otherwise).
[2] The operation must be done in a board (SoC) specific manner
since how to wake the slaves from the Boot ROM is SoC specific.
[3] The slaves must enter U-Boot proper after U-Boot relocates
itself because the "cpu-release-addr" property points to the
relocated memory area.
[2] is already explained in the help. We can make [1] even clearer
by mentioning "U-Boot proper" instead of "U-Boot". [3] is missing,
so I am adding it to the list. Instead, "before the master CPU
jumps to the kernel" is a matter of course, so removed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
