- Do not use irps54012 as device node which is not correct.
- Fix addresses of irps5401/u180 on zcu104 revisions.
- Remove clock-cells property. It is PMIC without any clock output.
- Define irps5401 nodes in zynqmp-e-a2197
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add label to GPIO lines controlling boot mode and POR EMIO pins so System
Controller can assert those lines on Versal.
Signed-off-by: Saeed Nowshadi <saeed.nowshadi@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Stack size has been introduced by commit a69814c815 ("arm64: zynqmp:
Set initrd_high to as high as possible") and commit 085201c246 ("arm64:
versal: Set initrd_high to as high as possible")
to support setting up initrd_high as high as possible.
The same change should happen for Zynq because the code is moved to xilinx
common location.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Offset value for CLKMGR_S10_PERPLL_BYPASS should be 0xb0, fix it.
Reported-by: Chee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
The Cubieboard is a single board computer containing a
Actions S700 SoC(with 4 ARMv8 Cortex-A53 cores).
This patch adds respective defconfig alongwith .dts(copied
from Linux v5.5-rc6 with hash "b3a987b0264d").
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This patch moves some of the config options from bubblegum_96_defconfig
to respective Kconfig files.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This patch adds basic support for Actions Semi based S700
SoC, which is driven by common owl framework.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Devices like uart and clk are needed to be enabled before relocation.
this patch adds u-boot.dtsi file that mark these device as dm-pre-reloc.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This patch adds .dtsi file(sync with Linux 5.5-rc6 with hash "b3a987b0264d")
and required binding for S700 SoC that is a 64-bit Quad-core ARM
Cortex-A53 cores.
It also provisions dts file to be built based on selected
platform(CONFIG_MACH_S900/S700).
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This patch converts S900 clock driver to something common that can
be used for other SoCs, for instance S700(few of clk registers are same).
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Devices like uart and clk are needed to be enabled before relocation.
This patch adds u-boot.dtsi file that mark these device as dm-pre-reloc.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Synchronize device tree bindings with v5.5-rc6 tag with commit id
"b3a987b0264d".
Also, it removes older clock binding defined for S900 along with undocumented
compatible string "actions,s900-serial" from serial driver and adapts clock
driver to cater to new bindings.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Now that memory maps(for both S700 and S900 SoCs) can be managed using
a common file, rename sysmap-s900 to sysmap-owl to reflect the same.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This commit adds common arch support for Actions Semi Owl
series SoCs and removes the Bubblegum96 board files.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Introduce arch_reserve_mmu to allow for architecture-specific reserve_mmu
routines. Also, define a weak nop stub for it.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As a preparation for turning reserve_mmu into an arch-specific variant,
introduce arm_reserve_mmu on ARM. It implements the default routine for
reserving memory for MMU TLB and needs to be weakly defined in order to allow
for machines to override it.
Without this decoupling, after introducing arch_reserve_mmu, there would be two
weak definitions for it, one in common/board_f.c and one in
arch/arm/lib/cache.c.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move the ARM-specific reserve_mmu definition from common/board_f.c
to arch/arm/lib/cache.c.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Split device tree for DHCOR Som and AV 96 board
- Update PLL4 setting in AV96 board
- Enable bootd, iminfo, imxtract on DHCOM
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl6jDmEACgkQ4rK92eCq
k3XwXQgAhCsdAF8qBa6qFqHY2APmfm1a3SLHUqEMEAh1y0R8bg3nSon3xDolGONB
9AIv4PVNjQyvG+8uJrdj/SLC1dKEYI1uU8gUPVau/V9yOR3purSa0RYg4gDRcs3T
8vwgGfp9kMwygOOVWdvd1YFnrDrtDF9OiF7i5ei7RhHRvMTThNa2Y1zeKI2z9svZ
XRNoED1/2G/ms4VOiRoxp5HhNH7akvG8VsZF9PhjEqsXtJoQ8uv7AMLOscnZHmh9
hol9voBValanfg3K2Hafubyq00ori51EvbhRJ10jDkXXkjgOflcHCVWIj4Ihq3oI
cQmUZ6eErS4uDYP4s7xvjE88Uxn0XA==
=uKKC
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200424' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Solve stm32mp15 pinctrl dts issue (patch conflict in branches master and next)
- Split device tree for DHCOR Som and AV 96 board
- Update PLL4 setting in AV96 board
- Enable bootd, iminfo, imxtract on DHCOM
The AV96 is in fact an assembly of DH Electronics DHCOR SoM on top
of an AV96 reference board. Split the DTs to reflect that and make
sure to DHCOR SoM can be reused on other boards easily.
It is also highly recommended to configure the board for the DHCOM
make stm32mp15_dhcom_basic_defconfig
make DEVICE_TREE=stm32mp15xx-dhcor-avenger96
as that permits reusing the board code for the DH components, like
accessing and reading out the ethernet MAC from EEPROM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Change-Id: I7db47280d4eb0d668eb4e006355240271154f97f
The PLL4 is supplying SDMMC12, SDMMC3 and SPDIF with 120 MHz and
FDCAN with 96 MHz. This isn't good for the SDMMC interfaces, which
can not easily divide the clock down to e.g. 50 MHz for high speed
SD and eMMC devices, so those devices end up running at 30 MHz as
that is 120 MHz / 4. Adjust the PLL4 settings such that both PLL4P
and PLL4R run at 100 MHz instead, which is easy to divide to 50MHz
for optimal operation of both SD and eMMC, SPDIF clock are not that
much slower and FDCAN is also unaffected.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Remove the unnecessary file stm32mp157-pinctrl.dtsi and
solve all issues introduced by the commit 8914831860 ("Merge branch
'next'") after a conflict on the patch applied in the next branch in
commit 1a4f57c895 ("ARM: dts: stm32mp1: DT alignment with Linux 5.6-rc1")
Need to reapplied on stm32mp15-pinctrl.dtsi the the 3 patches
applied previously on file "stm32mp157-pinctrl.dtsi" in v2020.04
- commit 4fdbe6487d ("ARM: dts: stm32: Add alternate pinmux for SDMMC1
direction pins")'
- commit 5fdcba6402 ("ARM: dts: stm32: Add alternate pinmux for SDMMC2
pins 4-7")'
- commit 955de51111 ("ARM: dts: stm32: Add alternate pinmux for ethernet
RGMII")'
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
- iproc_sdhci memory leak fix and enable R1B resp quirk
- more mmc cmds and several mmc updates from Heinirich
- Use bounce buffer for tmio sdhci
- Alignment check for tmio sdhci
This function is only relevant to the MMC driver so calling it
spl_boot_partition() might be confusing. Rename it to
spl_mmc_boot_partition() to make its purpose more clear (and bring
it in line with spl_mmc_boot_mode()).
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The function's name is misleading as one might think it is used
generally to select the boot-mode when in reality it is only used by the
MMC driver to find out in what way it should try reading U-Boot Proper
from a device (either using a filesystem, a raw sector/partition, or an
eMMC boot partition).
Rename it to spl_mmc_boot_mode() to make it more obvious what this
function is about.
Link: https://lists.denx.de/pipermail/u-boot/2020-April/405979.html
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update mvebu SPL boot selection mechanism for the move to driver model
usage by ensuring that the required driver support for SPI and MMC
booting is available in SPL when the respective boot method is
selected.
Previously, all mvebu boards selected a boot method (implicitly
MVEBU_SPL_BOOT_DEVICE_SPI for many) even if SPL booting wasn't used.
This changes mvebu boot method selection to depend on SPL usage which
resolves the issue with aarch64 boards which don't use SPL getting an
implicit boot device selection resulting in unmet dependencies. The
32-bit arm boards do use SPL, but I'm led to conclude that most aren't
intentionally using the MVEBU_SPL_BOOT_DEVICE selection since none have
SPL_DM_SPI enabled in their defconfig even though they still implicitly
select the SPI boot method.
This also results in the new addition of SPL_GPIO_SUPPORT to helios4.
The mainline dts for helios4 includes the cd-gpios entry for sdhci with
identical addresses as the clearfog dts. I don't have a helios4 board
to confirm, but based on the current source conclude that the board
itself is either wired to pull the signal low for eMMC, or the default
MMC boot isn't fully functional in mainline. In either case, as far as
I can tell, including the GPIO support will at least cause no
regression.
Tested on SolidRun ClearFog devices.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
- Further cleanups for 'make refcheckdocs'
- Another BTRFS fix.
- Support for automatic decompression of images with booti as well as
unlz4 command for manual decompression.
- fix SMBIOS info on Odroid-C2
- Fix video output on GXBB/GXL/GXM boards
- add USB gadget support for GXL/GXM boards
-----BEGIN PGP SIGNATURE-----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=1Ffl
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20200420' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- enable DM_RNG on meson boards
- fix SMBIOS info on Odroid-C2
- Fix video output on GXBB/GXL/GXM boards
- add USB gadget support for GXL/GXM boards
- Fix boot on am335x guardian board
- Increase OPSI speed on AM65x and J721E devices
- Use JTAD register for identifying K3 devices.
- Update TI entry in MAINTAINERS file.
Add the USB DWC2 node to u-boot specific dtsi files since Gadget
support is not (yet) available in upstream Linux yet.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add arch code to initialize USB Gadget mode using the DWC2 controller,
and using the previously added set_mode() phy functions.
[narmstrong: fixup board_usb_cleanup call to phy_meson_gxl_usb2_set_mode]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add set_mode function in the Amlogic GXL PHYs that will be called by
the arch code to switch PHYs from/to gadget mode.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add generic support for backplane kr modes currently available:
10gbase-kr, 40gbase-kr4. Remove platform generic fixups
(armv8/layerscape and powerpc) for ethernet interfaces specified
in device tree as supported backplane modes.
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch is to define esdhc_status_fixup function for ls1028a to disable
SDHC1/SDHC2 status in device tree node if not selected.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
JTAG ID register is defined by IEEE 1149.1 for device identification.
Use this JTAG ID register for identifying AM65x[0] and J721E[1] devices
instead of using SoC specific registers.
[0] http://www.ti.com/lit/ug/spruid7e/spruid7e.pdf
[1] http://www.ti.com/lit/ug/spruil1a/spruil1a.pdf
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Those two boards are supposed to be run with a single u-boot binary.
There are notable differences though - HSC uses DSA switch (which
phy_id == 0x0) and DCC (DP83848C).
After the commit 3bf135b6c3
("drivers: net: phy: Ignore PHY ID 0 during PHY probing") the PHY devices
with phy_id == 0 are not created in U-Boot anymore. This caused regression
on HSC.
To fix this problem - the fec's 'fixed-link' node has been introduced and
the phy_id is not assessed anymore. This approach works on both boards.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
During the conversion of this board to DM_REGULATOR, usb-mass-storage
was broken and started failing with the following error:
=> ums 0 mmc 2
UMS: LUN 0, dev 2, hwpart 0, sector 0x0, count 0xe90000
Error enabling VBUS supply
g_dnl_register: failed!, error: -38
g_dnl_register failed
Fix this by adding the relevant GPIO to the regulator node.
Fixes: 4ca99fe81a ("ARM: imx: dh-imx6: Enable DM regulator")
Signed-off-by: Harald Seiler <hws@denx.de>
Use DM_ETH instead of legacy networking. Add VIO as a fixed regulator
to the relevant device-trees and augment the FEC node with properties
for the reset GPIO.
It should be noted that the relevant properties for the reset GPIO
already exist in the PHY node (reset-gpios, reset-delay-us,
reset-post-delay-us) but U-Boot currently ignores those and only
supports the bus-level reset properties in the FEC node
(phy-reset-gpios, phy-reset-duration, phy-reset-post-delay).
Signed-off-by: Harald Seiler <hws@denx.de>
The detection of the revD1 version is based on the presence of the PMIC.
Currently revb1 device trees are used for mx6q/mx6dl variants, which
do not have the PMIC nodes.
This causes revD1 boards to be incorrectly be detected as revB1.
Fix this issue by using the revd1 device trees, so that the PMIC node can be
found and then the PMIC can be detected by reading its register ID.
Imported the revd1 device trees from mainline kernel version 5.7-rc1.
Reported-by: Heiko Schocher <hs@denx.de>
Reported-by: Derek Atkins <derek@ihtfp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Derek Atkins <derek@ihtfp.com>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Linux doesn't provide skeleton.dtsi file so let's remove its include and
provide #address-cells/size-cells = <1> that were defined in
skeleton.dtsi before.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Add support for i.MXRT by adding CONFIG_IMXRT in register structure and
adding .compatible = "fsl,imxrt-lcdif".
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
The device trees for TQMa6x SOM support variations in
- CPU type: imx6dl- or imx6q-
- MBa6 I2C bus access: -mba6a (i2c1) or -mba6b (i2c3)
(plus the respective common/module include trees)
- USBH1 is directly connected to a hub
- USBOTG is connected to a separate connector
and can act as host/device or full OTG port.
Signed-off-by: Michael Krummsdorf <michael.krummsdorf@ew.tq-group.com>
The i.MX6DP and i.MX6QP incorporate NoC interconnect logic
which needs to be configured in order to use external DDR memory.
This patch enables the SPL to configure the necessary registers
in accordance with the NXP engineering bulletin EB828.
Co-developed-by: Filip Brozović <fbrozovic@gmail.com>
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
LDO mode may be already enabled by the ROM and enabling it again
can cause U-Boot to hang.
Avoid this problem by only enabling LDO mode if it is initially disabled.
Reported-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
These PMC0 definitions are already defined in the beginning
of the file, so remove the duplication.
Reported-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
If gd->ram_top has been tuned using board_get_usable_ram_top(),
it must be taken into account when reserving arch lmb.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Simplify the arm relocation behavior and get gd directly form new_gd,
as it is already done in crt0_64.S:
ldr x18, [x18, #GD_NEW_GD] /* x18 <- gd->new_gd */
This patch avoid assumption on new GD location (new GD is below bd -
with #GD_SIZE offset).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This reverts the workaround introduced by the
commit 16fec9b0bc ("stm32mp1: remove the imply BOOTSTAGE")
As the bootstage alignment issue is now solved.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Update reference in files detected by
scripts/documentation-file-ref-check
doc/README.mxc_hab => doc/imx/habv4/*
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The Linux VPU bindings have changed and dropped the dmc register range.
Add it back in the meson-gx-u-boot.dtsi file until a proper canvas driver
is available.
Fixes: dd5f2351e9 ("arm64: dts: meson: sync dt and bindings from v5.6-rc2")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The libretech-ac u-boot.dtsi file is missing to enabled DT nodes changes
to enable Video output on U-Boot.
Fixes: 671b1db8f8 ("arm64: dts: meson-gx: vpu should be probed before relocation")
Reported-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
All ARCH_MESON boards have a hardware random number generator. So we should
enable building the RNG driver.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The LED labels do not match the silkscreen on the board, fix it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Activate ARCH_SUPPORT_TFABOOT and replace the arch stm32mp
specific config CONFIG_STM32MP1_TRUSTED by the generic CONFIG_TFABOOT
introduced by the commit 535d76a121 ("armv8: layerscape: Add TFABOOT
support").
This config CONFIG_TFABOOT is activated for the trusted boot chain,
when U-Boot is loaded by TF-A.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add DT entries, Kconfig entries and board-specific entries to configure
FMC2 bus and make KS8851-16MLL on that bus accessible to U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Define FMC2 base address, for use in board files, until there is an
actual FMC2 bus driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
- Misc enhancements to Clearfog, including board variant detection
(Joel)
- Misc enhancements to Turris Mox, including generalization of the
ARMADA37xx DDR size detection (Marek)
In case when ARM Trusted Firmware changes the default address of PCIe
regions (which can be done for devices with 4 GB RAM to maximize the
amount of RAM the device can use) we add code that looks at how ATF
changed the PCIe windows in the CPU Address Decoder and changes given
device-tree blob accordingly.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Currently on Armada-37xx the mem_map structure is statically defined to
map first 2 GB of memory as RAM region, and system registers and PCIe
region device region.
This is insufficient for when there is more RAM or when for example the
PCIe windows is mapped to another address by the CPU Address Decoder.
In the case when the board has 4 GB RAM, on some boards the ARM Trusted
Firmware can move the PCIe window to another address, in order to
maximize possible usable RAM.
Also the dram_init and dram_init_banksize looks for information in
device-tree, and therefore different device trees are needed for boards
with different RAM sizes.
Therefore we add code that looks at how the ARM Trusted Firmware has
configured the CPU Address Decoder windows, and then we update the
mem_map structure and compute gd->ram_size and gd->bd->bi_dram bank
base addresses and sizes accordingly.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Move Armada-8k specific DRAM init code into armada-8k specific
directory.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Commit e8e9715df2 requires the USB3 regulator node to have the
enable-active-high property for the regulator to work properly. The
GPIO_ACTIVE_HIGH constant is not enough anymore.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Fixes: e8e9715df2 ("regulator: fixed: Modify enable-active-high...")
Reviewed-by: Stefan Roese <sr@denx.de>
With recent changes to the mmc subsystem (chip detect code etc) update
the sdhci node of the Turris Mox device tree.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add a unique entry for ClearFog Base variant, reflected in the board
name and adjusted SerDes topology.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Using a consistent hardcoded MAC address from the DTS file causes
issues when using multiple devices on the same network segment.
Instead rely on environment configuration or random generation.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Update the RTC (Read Timing Control) values for PCIe memory wrappers
following an ERRATA (ERRATA# TDB). This means the PCIe accesses will
used slower memory Read Timing, to allow more efficient energy
consumption, in order to lower the minimum VDD of the memory. Will lead
to more robust memory when voltage drop occurs (VDDSEG)
The code is based on changes from Marvell's U-Boot, specifically:
20cd270407eb608a7c8dc4af19ae2b
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Sort the Armada series dts in the Makefile alphabetically
prior to adding new board support.
Signed-off-by: Josip Kelečić <josip.kelecic@sartura.hr>
Reviewed-by: Luka Kovacic <luka.kovacic@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
In 1 bit mode OSPI can work at upto 50MHz, this provides better write
performance. Therefore increase frequency from 40MHz to 50MHz
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
In 1 bit mode OSPI can work at upto 50MHz, this provides better write
performance. Therefore increase frequency from 40MHz to 50MHz
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
- As there is a requirement to store certain data, we need a persistent
storage in u-boot. Hence, we need to save env in NAND
- Add default Guardian environment variables
- Update partition table:
- Reserve some space for experimentation, this ensures proper
backwards compatibility
- Update defconfig accordingly
Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
This patch enables the guardian board to provide feedback
about the boot stage in headless mode. The on-board led
would behave in the following pattern
* U-boot -> GLOW LED
* Linux -> BLINK LED [HEART-BEAT PATTERN]
Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
Pull in changes that have been pending in our 'next' branch. This
includes:
- A large number of CI improvements including moving to gcc-9.2 for all
platforms.
- amlogic, xilinx, stm32, TI SoC updates
- USB and i2c subsystem updtaes
- Re-sync Kbuild/etc logic with v4.19 of the Linux kernel.
- RSA key handling improvements
Adding "u-boot,dm-pre-reloc" and enable CONFIG_SPL_CACHE
to enable cache driver in SPL.
This fixed error below in SPL:
cache controller driver NOT found!
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Update these 3 files from Linux:.
- socfpga_arria10.dtsi (Commit ID c1459a9d7e92)
- socfpga_arria10_socdk.dtsi (Commit ID d9b9f805ee2b)
- socfpga_arria10_socdk_sdmmc.dts (Commit ID 17808d445b6f)
Change in socfpga_arria10.dtsi:
- Add clkmgr label, so that can reference to it in u-boot.dtsi.
Change in socfpga_arria10-u-boot.dtsi:
- Add compatible and altr,sysmgr-syscon for uboot.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Move Uboot specific properties to *u-boot.dtsi files.
Preparation to sync Arria 10 device tree from Linux.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add and enable RTC-backed boot counter on ABB SECU1 platform.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
The FIT config node has reversed ATF and u-boot: ATF is set to 'firmware' but
u-boot is set to 'loadables'.
This script can work previously because spl fit driver wrongly appends fdt to
all loadable images. With the issue fixed in commit 9d15d1d1c2 ("Revert
"common: spl_fit: Default to IH_OS_U_BOOT if FIT_IMAGE_TINY enabled"") the
u-boot in 'loadables' does not have fdt appended and fails to work. So correct
the script by moving u-boot to 'firmware' and ATF to 'loadables'.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reported-by: Matt Porter <mporter@konsulko.com>
Tested-by: Matt Porter <mporter@konsulko.com>
- sync all Amlogic DT from Linux v5.6-rc2
- MMC clock fixups
- add support for Libre Computer AML-S905D-PC and AML-S912-PC
-----BEGIN PGP SIGNATURE-----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=PiOt
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20200406' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic into next
- clk: meson-g12a: missing break
- sync all Amlogic DT from Linux v5.6-rc2
- MMC clock fixups
- add support for Libre Computer AML-S905D-PC and AML-S912-PC
pd_dma_* nodes should be accessible during pre-relocation stage of
U-Boot proper for properly handling power domains.
This fixes the issue with permanent failing of invocation of
power_domain_get_by_index() in the common code of DM power domain
uclass (drivers/power/domain/power-domain-uclass.c).
Fixes: f0cc4eae9a ("core: device: use dev_power_domain_on")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
pd_dma_* nodes should be accessible during pre-relocation stage of
U-Boot proper for properly handling power domains.
This fixes the issue with permanent failing of invocation of
power_domain_get_by_index() in the common code of DM power domain
uclass (drivers/power/domain/power-domain-uclass.c).
Fixes: f0cc4eae9a ("core: device: use dev_power_domain_on")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
For non-SPL/TPL setups dm-spl, dm-tpl, dm-pre-proper, dm-pre-reloc are
handled equally, forcing the nodes with these properties
to be accessible and device being probed
before pre-relocation of U-Boot proper (drivers/core/util.c):
bool ofnode_pre_reloc(ofnode node)
{
/* for SPL and TPL the remaining nodes after the fdtgrep 1st pass
* had property dm-pre-reloc or u-boot,dm-spl/tpl.
* They are removed in final dtb (fdtgrep 2nd pass)
*/
return true;
if (ofnode_read_bool(node, "u-boot,dm-pre-reloc"))
return true;
if (ofnode_read_bool(node, "u-boot,dm-pre-proper"))
return true;
/*
* In regular builds individual spl and tpl handling both
* count as handled pre-relocation for later second init.
*/
if (ofnode_read_bool(node, "u-boot,dm-spl") ||
ofnode_read_bool(node, "u-boot,dm-tpl"))
return true;
return false;
}
Howewer, to avoid confusion in future, replace dm-spl
`%s/dm-spl/dm-pre-proper/g` properties to dm-pre-proper
to explicitly state that they are handled during pre-relocation
stage of U-Boot proper.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
For non-SPL/TPL setups dm-spl, dm-tpl, dm-pre-proper, dm-pre-reloc are
handled equally, forcing the nodes with these properties
to be accessible and device being probed
before pre-relocation of U-Boot proper (drivers/core/util.c):
bool ofnode_pre_reloc(ofnode node)
{
/* for SPL and TPL the remaining nodes after the fdtgrep 1st pass
* had property dm-pre-reloc or u-boot,dm-spl/tpl.
* They are removed in final dtb (fdtgrep 2nd pass)
*/
return true;
if (ofnode_read_bool(node, "u-boot,dm-pre-reloc"))
return true;
if (ofnode_read_bool(node, "u-boot,dm-pre-proper"))
return true;
/*
* In regular builds individual spl and tpl handling both
* count as handled pre-relocation for later second init.
*/
if (ofnode_read_bool(node, "u-boot,dm-spl") ||
ofnode_read_bool(node, "u-boot,dm-tpl"))
return true;
return false;
}
Howewer, to avoid confusion in future, replace dm-spl
`%s/dm-spl/dm-pre-proper/g` properties to dm-pre-proper
to explicitly state that they are handled during pre-relocation
stage of U-Boot proper.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Similar change was done in past by commit 3b644a3c2f
("arm64: zynqmp: Provide a config to not map DDR region in MMU table").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
If ATF doesn't exist generate u-boot.itb without it and let U-Boot run in
EL3. Still keep warning to let user know that ATF/BL31 is missing.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Delay required for clock propagation is tighly coupled with initialization
done in psu_init(). That's why call it also for u-boot proper with
CONFIG_ZYNQMP_PSU_INIT_ENABLED enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
board_early_init_f() is the right location where debug uart can be
configurated (after MIO initialization).
The patch is taking this call from SPL to also make it available for U-Boot
proper.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
I found this issue when was running py/test.py on zcu102 which is for me by
default setup to SD boot mode without any way to change boot mode.
Alternative software bootmode selection to JTAG is not working because JTAG
mode is 0 which also reset value for it. That's why saying SPL to take
u-boot.itb from RAM instead of SD in SD boot mode is not possible via
alternative bootmode selection.
That's why setup third boot mode to JTAG(BOOT_DEVICE_RAM) as final
fallback.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This information is shown already that's why there is no reason to print it
again via custom prints.
U-Boot SPL 2020.01-03080-ga6214d033bd0 (Mar 05 2020 - 09:59:05 +0100)
mmc boot
Trying to boot from MMC1
or
U-Boot SPL 2020.01-03080-ga6214d033bd0 (Mar 05 2020 - 10:49:46 +0100)
qspi boot
Trying to boot from SPI
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
With multi defconfig NOR flash information about NOR should be taken from
DT that's why there is no reason to specify address and sizes via fixed
config.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no real need to include full DT when only some nodes are enough to
use. It will save some space.
Retested with FSBL for initial SoC setup. SPL didn't work.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Users have option to overwrite default device tree
(CONFIG_DEFAULT_DEVICE_TREE) via environment variable DEVICE_TREE.
Feature has been added long time ago by commit 74de8c9a16
("dts/Makefile: Build the user specified dts") for a little bit different
reason.
But this variable can be also used for different purpose like choosing
proper configuration from FIT image in SPL.
And this is the functionality I would like to use on Xilinx Zynq devices
that current u-boot.img can be composed in the same way based on OF_LIST
and different configuration is taken based on platform specific SPL.
SPL requires low level ps7_init_gpl configuration that's why different
boards require different SPL with fixed board_fit_config_name_match().
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Instead of symlink include origin file and just change model description.
Difference is not in DT but in ps7_init configurations which is taken based
on device tree name that's why the same DT can't be used.
Also update model and update comments to match configurations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Pinctrl is handled via firmare interface that's why move it there without
reg property and new compatible string.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
dtbs_check is showing warning around GIC compatible property as
interrupt-controller@f9010000: compatible: ['arm,gic-400', 'arm,cortex-a15-gic']
is not valid under any of the given schemas
Similar change has been done also by Linux kernel commit 5400cdc1410b
("ARM: dts: sunxi: Fix GIC compatible")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Node name should be <name>@<address> which is not how partitions are
described.
Issue was found by running dtbs_check as:
flash@0: 'partition@qspi-device-tree', 'partition@qspi-fsbl-uboot',
'partition@qspi-linux', 'partition@qspi-rootfs'
do not match any of the regexes: ...
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Sync DP subsystem with the latest state in Xilinx U-Boot repository.
This binding hasn't been approved in mainline Linux but it is much better
than ancient version which this patch removes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In kernel 5.4, support has been added for reading MTD devices via
the nvmem API.
For this the mtd devices are registered as read-only NVMEM providers
under sysfs with the same name as the flash partition label property.
So if flash partition label property of multiple flash devices are identical
then the second mtd device fails to get registered as a NVMEM provider.
This patch fixes the issue by having different label property for different
flashes.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add clock-cells and clock-output-names for sdhci0 and sdhci1.
These are needed for linux sdhci driver from 5.4 version onwards.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reset controller is handled via firmware that's why it should be the part
of firmware node. Origin solution hasn't been removed when above change was
applied by commit b07e97b4ba ("arm64: zynqmp: Use reset header in
zynqmp.dtsi").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Modify dts files to add 'no-1-8-v' property for all the ZynqMP boards.
User can remove this property to enable the UHS mode. This is to keep
the same speed (HS) modes across all the stages of the Linux Boot. Due
to power cycling limitation of some of the ZynqMP boards, some SD cards
don't get power cycled and are failing in Linux.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Sync zynqmp fpga manager with mainline.
Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
None name address should be aligned with address. DTC 1.5.1 is reporting
issues related to that.
arch/arm/boot/dts/zynq-zc770-xm010.dts:106.10-119.4: Warning
(spi_bus_reg): /amba/spi@e0007000/flash@0: SPI bus unit address format
error, expected "1"
arch/arm/boot/dts/zynq-zc770-xm013.dts:101.19-109.4: Warning
(spi_bus_reg): /amba/spi@e0006000/eeprom@0: SPI bus unit address format
error, expected "2"
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The same change has been done for Zynq by commit 1241c72b6db1
("ARM: dts: zynq: replace gpio-key,wakeup with wakeup-source property")
in mainline Linux kernel.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Most of the legacy "gpio-key,wakeup" boolean property is already
replaced with "wakeup-source". However few occurrences of old property
has popped up again, probably from the remnants in downstream trees.
Replace the legacy properties with the unified "wakeup-source"
property introduced in the Linux kernel commit 700a38b27eef
("Input: gpio_keys - switch to using generic device properties")
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The dtc has new checks for I2C and SPI buses.
Fix the warnings in node names and unit-addresses.
Warning from Linux kernel:
arch/arm/boot/dts/zynq-zc702.dts:187.13-190.6: Warning (i2c_bus_reg): /amba/i2c@e0004000/i2c-mux@74/i2c@7/hwmon@52: I2C bus unit address format error, expected "34"
arch/arm/boot/dts/zynq-zc702.dts:191.13-194.6: Warning (i2c_bus_reg): /amba/i2c@e0004000/i2c-mux@74/i2c@7/hwmon@53: I2C bus unit address format error, expected "35"
arch/arm/boot/dts/zynq-zc702.dts:195.13-198.6: Warning (i2c_bus_reg): /amba/i2c@e0004000/i2c-mux@74/i2c@7/hwmon@54: I2C bus unit address format error, expected "36"
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Multi boot register can be used for using different boot images and design
better boot strategy. Let EL3 SPL or U-Boot to read it and print it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for the Amlogic based libretech-pc platform.
This platform comes with 2 variant, based on the s905d or s912 SoC.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[narmstrong: update board/amlogic/q200/MAINTAINERS]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Sync the libretech-pc device tree from Linux v5.6-rc2
11a48a5a18c6 ("Linux 5.6-rc2")
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Sync the device tree and dt-bindings from Linux v5.6-rc2
11a48a5a18c6 ("Linux 5.6-rc2")
The only exception to this is the mmc pinctrl pin bias of gxl SoC family.
This is a fix which found its way to u-boot but not Linux yet.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The card-detect GPIO and any other GPIO access currently doesn't work in
U-Boot SPL on any STM32 platform and crashes the SPL. To work around this
problem on AV96 right before release, remove the cd-gpios from DT. This
patch must be reverted right after release, once the proper fix for the
GPIO driver, "gpio: stm32: support gpio ops in SPL", is applied.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
When generating the MAC address based on the boards serial number
the last digit was overwritten with the null termination. That way
boards with serial numbers close to each other would use the same
MAC address.
Signed-off-by: Jan-Christoph Tebbe <Jan-Christoph.Tebbe@ithinx.io>
The Jetson Nano Developer Kit is a Tegra X1-based development board. It
is similar to Jetson TX1 but it is not pin compatible. It features 4GB
of LPDDR4, a SPI NOR flash for early boot firmware and an SD card slot
used for storage.
HDMI 2.0 or DP 1.2 are available for display, four USB ports (3 USB 2.0
and 1 USB 3.0) can be used to attach a variety of peripherals and a PCI
Ethernet controller provides onboard network connectivity. NVMe support
has also been added. Env save is at the end of QSPI (4MB-8K).
A 40-pin header on the board can be used to extend the capabilities and
exposed interfaces of the Jetson Nano.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
According to the HW team, for some reason the normal clock select code
picks what appears to be a perfectly valid 375KHz SD card clock, based
on the CAR clock source and SDMMC1 controller register settings (CAR =
408MHz PLLP0 divided by 68 for 6MHz, then a SD Clock Control register
divisor of 16 = 375KHz). But the resulting SD card clock, as measured by
the HW team, is 700KHz, which is out-of-spec. So the WAR is to use the
values given in the TRM PLLP table to generate a 400KHz SD-clock (CAR
clock of 24.7MHz, SD Clock Control divisor of 62) only for SDMMC1 on
T210 when the requested clock is <= 400KHz. Note that as far as I can
tell, the other requests for clocks in the Tegra MMC driver result in
valid SD clocks.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
As per the T210 TRM, when running at 3.3v, the SDMMC1 tap/trim and
autocal values need to be set to condition the signals correctly before
talking to the SD-card. This is the same as what's being done in CBoot,
but it gets reset when the SDMMC1 HW is soft-reset during SD driver
init, so needs to be repeated here. Also set autocal and tap/trim for
SDMMC3, although no T210 boards use it for SD-card at this time.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Fix VI_I2C clock source type. Will be needed by VI_I2C driver.
Also added use of INTERNAL_ID macro in two places, needed to keep
the id returned to 8 bits.
Signed-off-by: Tom Warren <twarren@nvidia.com>
T210 CBoot is now doing the full pinmux and GPIO init, based on the DTB
tables. Remove pinmux/GPIO init tables & code from all T210-based builds
below:
p2371-2180 aka TX1
p2371-0000
e2220-1170
p2571
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
This commit removes the programming sequence that enables PLLE and UPHY
PLL hardware power sequencers. Per TRM, boot software should enable PLLE
and UPHY PLLs in software controlled power-on state and should power
down PLL before jumping into kernel or the next stage boot software.
Adds call to board_cleanup_before_linux to facilitate this.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
This adds to the DT the I2C controllers that connect to the board ID EEPROM,
etc. With this change, you can now probe all I2C devices on a TX1 board.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Enable pre console buffer for rk3399 platform.
This would help to capture the console messages prior to
the console being initialised. Enabling this would help
to capture all the console messages on video output source
like HDMI. So we can find the full console messages of
U-Boot proper on HDMI display when enabled it for RK3399
platform boards.
Buffer address used for pre console is 0x0f200000 which is
ram base plus 240MiB. right now the Allwinner SoC is using
similar computation.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
VOP display endpoint pipeline configuration differs
between rk3288 vs rk3399.
These VOP pipeline configuration depends on how the
different display interfaces connected in sequence to
IN and OUT ports like for,
RK3288:
vopb_out: port {
#address-cells = <1>;
#size-cells = <0>;
vopb_out_edp: endpoint@0 {
reg = <0>;
remote-endpoint = <&edp_in_vopb>;
};
vopb_out_hdmi: endpoint@1 {
reg = <1>;
remote-endpoint = <&hdmi_in_vopb>;
};
vopb_out_lvds: endpoint@2 {
reg = <2>;
remote-endpoint = <&lvds_in_vopb>;
};
vopb_out_mipi: endpoint@3 {
reg = <3>;
remote-endpoint = <&mipi_in_vopb>;
};
};
RK3399:
vopb_out: port {
#address-cells = <1>;
#size-cells = <0>;
vopb_out_edp: endpoint@0 {
reg = <0>;
remote-endpoint = <&edp_in_vopb>;
};
vopb_out_mipi: endpoint@1 {
reg = <1>;
remote-endpoint = <&mipi_in_vopb>;
};
vopb_out_hdmi: endpoint@2 {
reg = <2>;
remote-endpoint = <&hdmi_in_vopb>;
};
vopb_out_mipi1: endpoint@3 {
reg = <3>;
remote-endpoint = <&mipi1_in_vopb>;
};
vopb_out_dp: endpoint@4 {
reg = <4>;
remote-endpoint = <&dp_in_vopb>;
};
};
here, HDMI interface has endpoint 1 in rk3288 and 2 in rk3399.
The rockchip vop driver often depends on this determined endpoint
number and stored in vop_mode. So based on this vop_mode the bpp
and pin polarity would configure on detected display interface.
Since, the existing driver using rk3288 vop mode settings enabling
the same will result wrong display interface configuration for rk3399.
Add the patch for fixing these vop modes for rk3399.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
compatibility with stm32mp15_dhcom_basic_defconfig
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl6EiK0ACgkQ4rK92eCq
k3V6DggAhU7jE5MGs9A7En+YpANXbJ4tl56IZIjdzPzEjA2G3yuBv/DLci/w27aF
eaP83ayI/ZrVtevEBFomP0JRrzQc9r/ot+USVugGsoAigLbzJc5uba42FGn09Olh
uKkst0Fb7uPRzZQNwRc7hTKVSLvT11c0oPQyhhJM2djPDTETDry+RPnEFQ41SEUt
bNILmj0VRzikzbe5RXFWWYMUWBrt22pG2LLhog+WSRSpqrWM2zES64NnwAXxD/mR
YIQFZIZ6eWW2Otp+qzenkg5ZWIMVWRyUBAP5e0auKRE8TGWAXgBcoFRTRLf7oA/P
yr3TTBMWiPdqdXNe3MYzAiTpm7jrtg==
=RALH
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200401' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Fix device tree of Avenger96 board from Arrow Electronics and add
compatibility with stm32mp15_dhcom_basic_defconfig
The core and vdd PMIC buck regulators were misconfigured, which caused
instability of the board and malfunction of high-speed interfaces, like
the RGMII. Configure the PMIC correctly to repair these problems. Also,
model the missing Enpirion EP53A8LQI on the DHCOR SoM as a fixed regulator.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
The AV96 RGMII uses different pinmux for ETH_RGMII_TXD0, ETH_RGMII_RXD2
and ETH_RGMII_TX_CTL. Use the correct pinmux to make ethernet operational.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Add another mux option for DWMAC RGMII, this is used on AV96 board.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
The board has an EEPROM on the same I2C bus as PMIC, at address 0x53.
The EEPROM contains the board MAC address.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Change-Id: I340a0675c11e4599968b2e3ef0515fb8da8d7b42
Use DT /aliases node to establish a stable phandle to the configuration
EEPROM. This permits the configuration EEPROM to be moved e.g. to a
different address or a different bus. Adjust the board code to handle
new phandle lookup.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
The DH Electronics DHCOR SOM has QSPI NOR on the SoM itself, add it
into the DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Change-Id: Ia7c454c496f50e3fc4851ec1154f3641c416e98e
The eMMC uses different pinmux for the top four data lines, use such
a pinmux, otherwise it takes a very long time until the test for 8bit
operation times out. And this is the correct pinmux per schematic too.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Add another mux option for SDMMC2 pins 4..7, this is used on AV96 board.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
The SD uses different pinmux for the D123DIRline, use such a pinmux,
otherwise there is a pinmux collision on the AV96. Add missing SD
voltage regulator switch and enable SDR104 operation.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Add another mux option for SDMMC1 direction pins, in particular
SDMMC1_D123DIR, this is used on AV96 board.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
The sdmmc1_dir_pins_a: sdmmc1-dir-0 layout changed in commit 35a54d41d9
("ARM: dts: stm32mp1: sync device tree with v5.2-rc4") such that pins{};
became pins1{};pins2{};, however the SPL extras were not updated to reflect
that change. Fix this.
This fixes booting from SD1 X9 slot on the AV96 board.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Fixes: 35a54d41d9 ("ARM: dts: stm32mp1: sync device tree with v5.2-rc4")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Add save_boot_params() to save reset status value from bootrom.
Bootrom will clear the status register in reset manager and stores the
reset status value in shared memory. Bootrom stores shared data at last
2KB of onchip RAM.
This function save reset status provided by bootrom to rst_mgr_status.
More information about reset status register value can be found in reset
manager register description.
When running in debugger without bootrom, r0 to r3 are random values.
So, skip save the value when r0 is not bootrom shared data address.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Configure RX and TX bus-width values to use flexspi in octal I/O mode.
If bus-widths are not specified, then single I/O mode is set by default.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Configure RX and TX bus-width values to use flexspi in octal I/O mode.
If bus-widths are not specified, then single I/O mode is set by default.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
lx2160a-qds has 2 micron "mt35xu512aba" flashes of size 64M each
connected on A0 and B1 i.e on CS0 and CS3. Since flashes are connected
on different buses, only one flash can be probed at a time.
Add fspi node properties aligned with LX2160A-RDB fspi properties.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1046A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1043A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Select BOARD_LATE_INIT config so that many board works can be done
in late init stage.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add IIC3 node from mainline Linux DT. This will be further updated in
subsequent DT sync, however adding this node for now is sufficient and
minimal change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since commit 79030a4861 ("rockchip: Add Single boot image
(with binman, pad_cat)") the following boot regression is seen:
U-Boot 2020.04-rc3-00050-gd16e18ca6c-dirty (Mar 09 2020 - 11:40:07 -0300)
Model: Elgin RV1108 R1 board
DRAM: 128 MiB
initcall sequence 67fd12a0 failed at call 6000b927 (err=-22)
This happens because the above commit missed to include the
"rockchip-u-boot.dtsi" for rv1108, so include this file
like it done for other Rockchip SoC dtsi's.
Fixes: 79030a4861 ("rockchip: Add Single boot image (with binman, pad_cat)")
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to make the console pins more robust to noise, activate
the pullups and increase its drive strength.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This parameter "st,phy-cal" becomes optional and when it is
absent the built-in PHY calibration is done.
It is the case in the helper dtsi file "stm32mp15-ddr.dtsi"
except if DDR_PHY_CAL_SKIP is defined.
This patch also impact the ddr interactive mode
- the registers of the param 'phy.cal' are initialized to 0 when
"st,phy-cal" is not present in device tree (default behavior when
DDR_PHY_CAL_SKIP is not activated)
- the info 'cal' field can be use to change the calibration behavior
- cal=1 => use param phy.cal to initialize the PHY, built-in training
is skipped
- cal=0 => param phy.cal is absent, built-in training is used (default)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Need to increase the LPDDR2/LPDDR3 the voltage vdd2_ddr: buck2
form 1.2V to 1.25V for 32bits configuration.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
This commit manages diversity for STM32M15x SOCs with:
- dedicated files to support all STM32MP15 SOCs family.
The differences between those SOCs are:
-STM32MP151 [1]: common file.
-STM32MP153 [2]: STM32MP151 + CANs + a second CortexA7-CPU.
-STM32MP157 [3]: STM32MP153 + DSI + GPU.
- new files to manage security diversity on STM32MP15x SOCs.
On STM32MP15xY, "Y" gives information:
-Y = A means no cryp IP and no secure boot.
-Y = C means cryp IP + secure boot.
- stm32mp157 pinctrl files to better manage package diversity.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
This path allows to set the cntfrq register of targeted cpu.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
The STM32MP1 series is available in 3 different lines which are pin-to-pin
compatible:
- STM32MP157: Dual Cortex-A7 cores, Cortex-M4 core @ 209 MHz,
3D GPU, DSI display interface and CAN FD
- STM32MP153: Dual Cortex-A7 cores, Cortex-M4 core @ 209 MHz
and CAN FD
- STM32MP151: Single Cortex-A7 core, Cortex-M4 core @ 209 MHz
Each line comes with a security option (cryptography & secure boot)
& a Cortex-A frequency option :
- A : Cortex-A7 @ 650 MHz
- C : Secure Boot + HW Crypto + Cortex-A7 @ 650 MHz
- D : Cortex-A7 @ 800 MHz
- F : Secure Boot + HW Crypto + Cortex-A7 @ 800 MHz
This patch adds the support of STM32MP15xD and STM32MP15xF in U-Boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Update the kernel device tree for STM32MP15x product lines according
the used soc and its part number, when CONFIG_OF_SYSTEM_SETUP is activated:
- STM32MP15XA hasn't Crypto (cryp1/2)
- STM32M151 and STM32M153 hasn't 3D GPU and DSI host
- STM32M151 hasn't CAN FD and has single A7
For example:
FDT: cpu 1 node remove for STM32MP151AAA Rev.B
FDT: can@4400e000 node disabled for STM32MP151AAA Rev.B
FDT: gpu@59000000 node disabled for STM32MP151AAA Rev.B
FDT: dsi@5a000000 node disabled for STM32MP151AAA Rev.B
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Add a function get_soc_name to get a string with the full name
of the SOC "STM32MP15xxx Rev.x"
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Add the SMC code and operation for trace on errors.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Add BSEC lock access (read / write) at 0xC0000000 offset of misc driver.
The write access only available for Trusted boot mode, based on new
SMC STM32_SMC_WRLOCK_OTP.
With the fuse command, the permanent lock status is accessed with
0x10000000 offset (0xC0000000 - 0x8000000 for OTP sense/program
divided by u32 size), for example:
Read lock status of fuse 57 (0x39)
STM32MP> fuse sense 0 0x10000039 1
Sensing bank 0:
Word 0x10000039: 00000000
Set permanent lock of fuse 57 (0x39)
STM32MP> fuse prog 0 0x10000039 1
Sensing bank 0:
Word 0x10000039: 00000000
WARNING: the OTP lock is updated only after reboot
WARING: Programming lock or fuses is an irreversible operation!
This may brick your system.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Remove the test offs < 0 , as offs is unsigned.
This patch solves the warnings when compiling with W=1
on stm32mp1 board:
In function ‘stm32mp_bsec_read’:
arch/arm/mach-stm32mp/bsec.c:368:11: warning:
comparison of unsigned expression < 0 is always false [-Wtype-limits]
368 | if (offs < 0 || (offs % 4) || (size % 4))
| ^
In function ‘stm32mp_bsec_write’:
arch/arm/mach-stm32mp/bsec.c:405:11: warning:
comparison of unsigned expression < 0 is always false [-Wtype-limits]
405 | if (offs < 0 || (offs % 4) || (size % 4))
| ^
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Some config symbols are found in *almost* every _defconfig file for
Allwinner boards, because those options are actually a platform choice,
and not a per-board decision.
Some of these options are older, some have recently been added.
Move those options to be set for all Allwinner boards in their
respective Kconfig files.
The rationales are as follows:
- NR_DRAM_BANKS: All Allwinner SoC map DRAM at one contiguous region of
address space only, starting at 1 GB. So it's always one bank.
- SPL_{DOS,EFI}_PARTITION: The Allwinner SPL does only support raw MMC
accesses, we don't care about filesystems or partitions in there, so
there is no need to define those symbols at all.
- USE_PREBOOT: We start USB early when a keyboard is configured, using the
preboot env variable, so we need to set this variable.
- SYS_RELOC_GD_ENV_ADDR: We don't specify any ENV_ADDR, so need this
symbol to be set (according to 8d8ee47e03).
- SYS_USB_EVENT_POLL_VIA_INT_QUEUE: According to commit eab9433aa5,
specifying this reduces the latency of the USB keyboard handling, so
this was formerly enabled in config headers for all Allwinner boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The Allwinner H6 SoC uses a quite different memory map, also changes the
clocks quite a bit. This requires some changes to the SPL SPI routine,
which hardcodes these values so far.
Using the just introduced helper functions to determine base address
and SPI controller generation, we can cover some of these differences
easily.
The clock setup is different, so requires some explicit code changes
there (reset and clock gate in one register at a different address).
Also we need to change the pinmux function to use a different set of
pins that the H6 uses for SPI0.
Eventually we can enable the H6 to use SPI booting in Kconfig.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Now that we can easily select an SoC specific SPI0 base address, adding
support for the Allwinner R40 is fairly trivial:
We set the base address, add this SoC to the ones that use PC23 and
enable it in Kconfig.
This allows booting from SPI flash on R40 boards.
Tested on a Bananapi M2 Berry with SPI flash connected to the header pins.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
So far we were using the CONFIG_SUNXI_GEN_SUN6I symbol to select between
the two SPI controller generations used on Allwinner SoCs. This is a
convenience symbol to roughly differentiate between "older" and "newer"
generation of SoCs.
The H6 SoCs is the newest SoC so far, but is sufficiently different to
not define this symbol. However it is using a SPI controller compatible
to the "new gen" SoCs.
To prepare for H6 support, we replace the check for this single symbol
with an explicit function, which can later be extended.
For now we just return CONFIG_SUNXI_GEN_SUN6I in there, so this does not
create a functional change.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
So far on all supported Allwinner SoCs we find the old generation SPI
controller always at address 0x1c05000, and the new generation one at
0x1c68000. However the Allwinner R40 SoC has a new generation SPI at
the old address, and the H6 uses a completely different address.
So split off the base address from the respective SPI registers, by
changing the #defines to just contain offsets.
The base address is provided by a function, so it can easily be extended
later when support for those SoCs materialises.
This does not change the code size (since the toolchain is clever enough
to optimise this properly), also does not bring any functional change at
this point.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Using memcpy() for some MMIO access is generally frowned upon and might
break things on some platforms. Allwinner H3, which fails to boot, being
an example here.
Moreover, fields being accessed are naturally aligned and warnings
produced by GCC have been quiesced for some time already by:
53dc8ae ("gcc-9: silence 'address-of-packed-member' warning")
That said, it should be okay to revert this commit.
This reverts commit 9bd34a69a4.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
K3 J721E:
* OSPI boot support
* Support for loading remote cores in R5 SPL
* PMIC ESM Support
* Minor fixes for R5F and C7x remoteproc drivers
K3 AM654:
* Update AVS class 0 voltages.
* Add I2C nodes
DRA7xx/AM57xx:
* Fixed Android boot on AM57xx
AM33/AM43/Davinci:
* switch to driver model for the net and mdio driver for baltos
* Add DM/DTS support for omap video driver
* Enable fastboot on am335x-evm
As there is only one linker script to use in this case, rather than use
the BOARDDIR variable hard-code the path.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Suggested-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
As there is only one machine under mach-orion5x, having a Kconfig entry
for SPL_LDSCRIPT is not helpful, move this to the defconfig file.
Suggested-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
The A72 U-Boot code supports early load and boot of a number of
remote processors including the C66_0 and C66_1 DSPs. The current
code supports only loading into the DDR regions which were already
given the appropriate memory attributes. The C66 DSPs also have L1
and L2 internal memory regions that can behave as normal-memories.
Add a new entry to the J721E MMU table covering these regions with
the appropriate memory attributes to allow the A72 U-Boot code to
support loading directly into these memory regions.
Signed-off-by: Suman Anna <s-anna@ti.com>
Add a separate function for printing sysfw version so that it can be
called independently of k3_sysfw_loader.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The binman-option BINMAN_FDT is introduced by this commit:
commit 3c10dc95bd ("binman: Add a library to access binman entries")
BINMAN_FDT being selected when BINMAN=y that resulting in mt7623
and mt7622 are unable to boot. The root cause of this issue is commit:
commit cbd2fba1ec ("arm: MediaTek: add basic support for MT7629 boards")
select BINMAN=y in all mediatek SoCs, and others mediatek SoCs not
expect to use BINMAN_FDT.
This patch remove BINMAN=y option when ARCH_MEDIATEK=y and
move this to the specify SoCs part config.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Correct the dependency for STM32 ETZPC protection, linked to SOC
STM32MP identified by CONFIG_STM32MP15x and not linked to
CONFIG_TARGET_STM32MP1 (no more existing).
This patch fix an issue introduced by commit 846254888e ("stm32mp1:
split board and SOC support for STM32MP15x family").
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Instead of resetting the ethernet phy through functions in imx8mq_evk.c, let the
driver reset the phy via dts description adding a reset duration of 10 ms
following atheros 8031's datasheet recommendation.
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
The FEC in the i.MX8MM doesn't support this feature. So don't pretend one
can use it.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Let pinctrl configuration for eMMC node (usdhc1) also be
accessible in SPL.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
The current implementation in arch/arm/mach-imx/cpu.c uses non-DM
code to retrieve the core clock frequency. As the root clock is not
listed we currently get:
CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz
Fix this by adding the missing entry, which results in:
CPU: Freescale i.MX8MMQ rev1.0 at 1200 MHz
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Before DM_VIDEO conversion this board used 24bpp
display configuration, so use it again.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
