Hi,
There is a bug in the code of clearing the bss section for processor
i386.(File: cpu/i386/start.S)
In the code, bss_start addr (starting addr of bss section) is put into
the register %eax, but the code which clears the bss section refers to
the addr pointed by %edi.
This patch fixes this bug by putting bss_start into %edi register.
Signed-off-by: Mushtaq Khan <mushtaq_k@procsys.com>
current PHY initalization code (tftp timeouts all the time). This commit
temporarily disables PHY initalization sequence to make the networking
operational, until a fix is found.
Some device trees have a mac-address property, some have local-mac-address,
and some have both. To support all of these device trees, ftp_cpu_setup()
should write the MAC address to mac-address and local-mac-address, if they
exist.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
MPC5200B systems are incorrectly reported as MPC5200 in U-Boot start-up
message. Use PVR to distinguish between the two variants, and print proper CPU
information.
Signed-off-by: Grzegorz Wianecki <grzegorz.wianecki@gmail.com>
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* Cleaned up the CDS PCI Config Tables and added NULL entries to
the end
* Fixed PCIe LAWBAR assignemt to use the cpu-relative address
* Fixed 85xx PCI code to assign powar region sizes based on the
config values (rather than hard-coding them)
* Fixed the 8548 CDS PCI2 IO to once again have 0 as the base address
Signed-off-by: Andy Fleming <afleming@freescale.com>
This included some changes to common files:
* Add 8568 processor SVR to various places
* Add support for setting the qe bus-frequency value in the dts
* Add the 8568MDS target to the Makefile
Signed-off-by: Andy Fleming <afleming@freescale.com>
Define CFG_DDR_SDRAM_CLK_CNTL for the MPC8349E-mITX and MPC8349E-mITX-GP.
This allows ddr->sdram_clk_cntl to be properly initialized. This is necessary
on some ITX boards, notably those with a revision 3.1 CPU.
Also change spd_sdram() in cpu/mpc83xx/spd_sdram.c to not write anything into
ddr->sdram_clk_cntl if CFG_DDR_SDRAM_CLK_CNTL is not defined.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Michael Benedict <MBenedict@twacs.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Clarified that conversion is to DRAM clocks rather than platform clocks.
Made function static to spd_sdram.c.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Changed the code to read the registers and calculate the clock
rates, rather than using a "switch" statement.
Idea from Andrew Klossner <andrew@cesa.opbu.xerox.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
e500v2 and newer cores support 1G page sizes.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Enable single-bit error counter when memory was cleared by ddr controller.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Some device trees have a mac-address property, some have local-mac-address,
and some have both. To support all of these device trees, ftp_cpu_setup()
should write the MAC address to mac-address and local-mac-address, if they
exist.
Signed-off-by: Timur Tabi <timur@freescale.com>
* Cleaned up the TSR[WIS] clearing
* Cleaned up DMA initialization
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Recognize new SVR values, and add a few register definitions
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
The following patch fixes the e500 v2 core reset bug.
For e500 v2 core, a new reset control register is added to reset the
processor.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Remove the fixed TLB and LAW entry nubmer. Use actually TLB and LAW
entry number to control the loop. This can reduce the potential risk
for the 85xx processor increasing its TLB adn LAW entry number.
Signed-off-by: Swarthout Edward <swarthout@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Board code can now request the generic setup code rather than having to
copy-and-paste it for themselves. Boards should be converted to use this
once they're tested with it.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Rather than misleadingly define PVR_83xx as the specific type of 83xx
being built for, the PVR of each core revision is defined. checkcpu() now
prints the core that it detects, rather than aborting if it doesn't find
what it thinks it wants.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Some device trees have a mac-address property, some have local-mac-address,
and some have both. To support all of these device trees, ftp_cpu_setup()
should write the MAC address to mac-address and local-mac-address, if they
exist.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Now 405EZ ports also show upon bootup from which boot device
they are configured to boot:
U-Boot 1.2.0-gd3832e8f-dirty (Apr 18 2007 - 07:47:05)
CPU: AMCC PowerPC 405EZ Rev. A at 199.999 MHz (PLB=133, OPB=66, EBC=66 MHz)
Bootstrap Option E - Boot ROM Location EBC (32 bits)
16 kB I-Cache 16 kB D-Cache
Board: Acadia - AMCC PPC405EZ Evaluation Board
Signed-off-by: Stefan Roese <sr@denx.de>
Use "setter" functions instead of flags, cleaner and more flexible.
It also fixes the problem noted by Timur Tabi that the ethernet MAC
addresses were all being set incorrectly to the same MAC address.
Driver for the Atmel MCI controller (MMC interface) for AT32AP CPUs.
The AT91 ARM-based CPUs use basically the same hardware, so it should
be possible to share this driver, but no effort has been made so far.
Hardware documentation can be found in the AT32AP7000 data sheet,
which can be downloaded from
http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Implement functions for configuring the mmci pins, as well as
functions for getting the clock rate of the mmci controller.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Implement functions for configuring the macb0 and macb1 pins, as
well as functions for getting the clock rate of the various
busses the macb ethernet controllers are connected to.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Relocate the u-boot image into SDRAM like everyone else does. This
means that we can handle much larger .data and .bss than we used to.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Rewrite the resource management code (i.e. I/O memory, clock gating,
gpio) so it doesn't depend on any global state. This is necessary
because this code is heavily used before relocation to RAM, so we
can't write to any global variables.
As an added bonus, this makes u-boot's memory footprint a bit smaller,
although some functionality has been left out; all clocks are enabled
all the time, and there's no checking for gpio line conflicts.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Split the avr32 initialization code into a function to run before
relocation, board_init_f and a function to run after relocation,
board_init_r. For now, board_init_f simply calls board_init_r
at the end.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
There are a few bugs in the cpu/mpc83xx/spd_sdram.c
the first bug is that the picos_to_clk routine introduces a huge
rounding error in 83xx.
the second bug is that the mode register write recovery field is
tWR-1, not tWR >> 1.
This patch fixes changes the i2c_init(...) function to use the function
get_OPB_freq() rather than calculating the OPB speed by
sysInfo.freqPLB/sysInfo.pllOpbDiv. The get_OPB_freq() function is
specific per processor. The prior method was not and so was calculating
the wrong speed for some PPC4xx processors.
Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Move the 8641HPCN's PIXIS code to the new directory
board/freescale/common/ as it will be shared by
future boards not in the same processor family.
Write a "pixis_reset" command that utilizes the FPGA
reset sequencer to support alternate soft-reset options
such as using the "alternate" flash bank, enabling
the watch dog, or choosing different CPU frequencies.
Add documentation for the pixis_reset to README.mpc8641hpcn.
Signed-off-by: Haiying Wang <haiying.wang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Fix a bug in the auto calibration routine. This driver now runs
more reliable with the tested modules. It's also tested with
167MHz PLB frequency (667MHz DDR2 frequency) on the Katmai.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds some 4xx GPIO functions. It also moves some of the
common code and defines into a common 4xx GPIO header file.
Signed-off-by: Stefan Roese <sr@denx.de>
Prevent false interrupt from hanging Linux as MSR[EE] is set
to enable interrupts by changing the PIC out of the default
pass through mode into mixed mode.
Signed-off-by: Haiying Wang <haiying.wang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Without this patch, I am unable to get to the prompt on rev 2 silicon.
Only set ddrioovcr for rev1.
Signed-off-by: Ed Swarthout<ed.swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
This patch adds support for the new AMCC 405EZ PPC. It is in
preparation for the AMCC Acadia board support.
Please note that this Acadia/405EZ support is still in a beta stage.
Still lot's of cleanup needed but we need a preliminary release now.
Signed-off-by: Stefan Roese <sr@denx.de>
timer support
interrupt controller support
flash support
ethernet support
cache support
board information support
env support
booting image support
adding support for Xilinx ML401
