Add DEK blob encapsulation support for IMX8M through "dek_blob" command.
On ARMv8, u-boot runs in non-secure, thus cannot encapsulate a DEK blob
for encrypted boot.
The DEK blob is encapsulated by OP-TEE through a trusted application call.
U-boot sends and receives the DEK and the DEK blob binaries through OP-TEE
dynamic shared memory.
To enable the DEK blob encapsulation, add to the defconfig:
CONFIG_SECURE_BOOT=y
CONFIG_FAT_WRITE=y
CONFIG_CMD_DEKBLOB=y
Signed-off-by: Clement Faure <clement.faure@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add signature with crc32 value for all images in binman node for FIT
image in device tree. And, enable FIT signature checking for Stratix10
and Agilex ATF and VAB sdmmc boot.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Add support for iMX8MN LPDDR4 EVK board which uses 2GB LPDDR4 and
PCA9450B PMIC.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Trusted Firmware now adds the /reserved-memory subnode to the DT at
runtime[1], putting in the right values.
Drop our hard-coded version, as this might clash with the actual values
(which have also changed), and rely on TF-A to add the node.
[1] https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/7770
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Loading Trusted-Firmware's BL31 at 16KB into DRAM was originally a hack
to allow sharing more code with the other SoCs (which use this offset
in SRAM). However there is no longer a reason for that, as the
problematic macros have been properly separated there.
The latest (and hopefully final) TF-A code drop now changes the load
address to the beginning of DRAM, which is also more easily protected
by the Trustzone memory controller (code to be done).
Adjust the load address of BL31 now, to avoid any issues with
incompatible versions later on (the TF-A patches are about to be merged).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
There are several changes which happen in mainline kernel which should get
also to U-Boot. Here is the list of patches from the kernel:
- ARM: zynq: Fix leds subnode name for zc702/zybo-z7
- arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1
- arm64: dts: zynqmp: Fix u48 si5382 chip on zcu111
- arm64: dts: zynqmp: Wire up the DisplayPort subsystem
- arm64: dts: zynqmp: Add DisplayPort subsystem
- arm64: dts: zynqmp: Add DPDMA node
- arm64: dts: zynqmp: Enable phy driver for Sata on zcu102/zcu104/zcu106
- arm64: dts: zynqmp: Enable si5341 driver for zcu102/106/111
- arm64: dts: zynqmp: Add DT description for si5328 for zcu102/zcu106
- arm64: dts: zynqmp-zcu100-revC: correct interrupt flags
- arm64: dts: xilinx: align GPIO hog names with dtschema
- arm64: zynqmp: Add Xilinx AES node
- dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA
but also some other changes have been done.
- Using only one compatible string for adxl345 on zturn
- Remove Xilinx internal DP bindings
- Remove USB3.0 serdes configurations
- Remove SATA serdes configuration for zc1232
- Resort nvmem_firmware
- Update nand compatible string
- Aling power-domains property for sd0/1
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In zynqmp.dtsi file renamed "clk_sys" clock to "controller" and
"clk_flash" clock to "bus" as per upstreamed Arasan NAND driver.
This fixes NAND driver probe failure.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Update the following device tree properties for nand flash
- Set software ecc mode.
- Set bch as ecc algo.
- Set read block to 0.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
EMMC will have bus-width 8 and it is non-removable in general. These
are missing from dt node. Add bus-width and non-removable parameters
to emmc node.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add initial support for NanoPi M4B, a minor revision of
the original NanoPi M4.
Commit details of rk3399-nanopi-m4b.dts sync from Linux 5.12-rc4:
"arm64: dts: rockchip: Add NanoPi M4B board"
(sha1: c7b03115003f7f337ab165542cee37148cf30a8a)
Signed-off-by: Alexandre Vicenzi <alexandre.vicenzi@suse.com>
Reviewed-by: Kever Yang <kever.yang@rock-cihps.com>
NanoPi R4s is SBC base on Rockchip RK3399 hexa-core processor with
dual-Core Cortex-A72 and Mali-T864 GPU with 4GiB(LPDDR4) of RAM, SD card support,
including 2 gigabit ethernet(RTL8211E 1Gbps - RTL8111H 1Gbps) and 2 USB 3.0 port.
port.It also has two GPIO headers which allows further peripherals to be used.
The devicetree file is taken of the rk3399 nanopi4 Linux kernel [1].
[1] e7a0959082
Signed-off-by: xiaobo <peterwillcn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A commit from last year re-imported the DTS files form the upstream kernel.
By doing so the VDD_LOG regulator in the board's DTS was dropped.
Let's restore this, but move it into the u-boot overlay to prevent this
issue in the future.
Fixes: 167efc2c7a ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux")
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This brings the actual rk3368-lion devicetree files from Linux 5.10
instead of using something separate.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This is the state as of v5.10 + the recently added timer0 phandle
targetted at the 5.12 merge window.
With this the non-mainline nodes like the dmc move to a separate
rk3368-u-boot.dtsi that is included from the board-specific
-u-boot.dtsi files, similar to how rk3399 does this.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This patch makes use of the decompression mechanism implemented for mt7628
previously to reduce the total image size. Binman will be also removed.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The EPHY LEDs belongs to the built-in FE switch of MT7629, which is barely
used. These LED pins on reference boards are used as JTAG socket. So it's
a good idea to change the default state to JTAG, and this will make it
convenience for debugging.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The EK874 development kit from Silicon Linux is made of CAT874 (the main
board) and CAT875 (the sub board that goes on top of CAT874).
This patch adds the required board support to boot Si-Linux EK874 board
based on R8A774C0 SoC.
DTS files apart from r8a774c0-ek874-u-boot.dts and r8a774c0-u-boot.dtsi
have been imported from Linux kernel 5.11 commit f40ddce88593
("Linux 5.11").
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
The HiHope RZ/G2H board from HopeRun consists of main board
(HopeRun HiHope RZ/G2H main board) and sub board(HopeRun
HiHope RZ/G2H sub board). The HiHope RZ/G2H sub board sits
below the HiHope RZ/G2H main board.
This patch adds the required board support to boot HopeRun HiHope
RZ/G2H board.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
The HiHope RZ/G2N board from HopeRun consists of main board
(HopeRun HiHope RZ/G2N main board) and sub board(HopeRun
HiHope RZ/G2N sub board). The HiHope RZ/G2N sub board sits
below the HiHope RZ/G2N main board.
This patch adds the required board support to boot HopeRun HiHope
RZ/G2N board.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
The HiHope RZ/G2M board from HopeRun consists of main board
(HopeRun HiHope RZ/G2M main board) and sub board(HopeRun
HiHope RZ/G2M sub board). The HiHope RZ/G2M sub board sits
below the HiHope RZ/G2M main board.
This patch adds the required board support to boot HopeRun HiHope
RZ/G2M board.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
- stm32mp1_trusted_defconfig rely on SCMI support
- Remove the nand MTD configuration for NOR boot in stm32mp1 board
- STM32programmer update
- Bsec: manage clock when present in device tree
- stm32mp15: move bootdelay configuration in defconfig
- Update for stm32 dsi and dw_mipi_dsi
- STM32 MCU's cleanup
- Fix compilation issue depending on SYS_DCACHE_OFF and SYS_ICACHE_OFF flags
- Update stm32mp1 doc
-----BEGIN PGP SIGNATURE-----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=nIJc
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210312' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Add WATCHDOG_RESET() in MTD framework and STM32 QSPI driver
- stm32mp1_trusted_defconfig rely on SCMI support
- Remove the nand MTD configuration for NOR boot in stm32mp1 board
- STM32programmer update
- Bsec: manage clock when present in device tree
- stm32mp15: move bootdelay configuration in defconfig
- Update for stm32 dsi and dw_mipi_dsi
- STM32 MCU's cleanup
- Fix compilation issue depending on SYS_DCACHE_OFF and SYS_ICACHE_OFF flags
- Update stm32mp1 doc
Define in the RCC clock provider node which root clocks the driver
depends on. These are root oscillators, which may be present or
not, upon FDT content.
This update binding is introduced in Linux kernel device tree by patch
"ARM: dts: stm32: move clocks/resets to SCMI resources for stm32mp15"
This patch is a preliminary step for SCMI support of stm32mp15
boards with trusted boot chain, based on TF-A or OP-TEE.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Commit 247bbeb74c ("ARM: dts: imx8m: increase off-on delay on the SD Vcc
regulator") caused the imx8mq-evk board to not be able to store the
environment variables in the SD card.
Remove the u-boot,off-on-delay-us property to fix the regression.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Add phy-reset-duration and phy-reset-post-delay to FEC node for PHY
reset, otherwise the PHY does not work correctly.
Signed-off-by: Ye Li <ye.li@nxp.com>
Make the conversion to driver model as it is mandatory.
Successfully tested booting Linux from the SD card.
Dropped splash screen support as this needs to be properly
converted to DM and tested.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Import the imx23-evk devicetree files from Linux kernel
version 5.11.
This is in preparation for converting the mx23evk_defconfig
target to driver model.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Make the conversion to driver model as it is mandatory.
Tested booting the Linux kernel from the SD card.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Import the imx51-babbage devicetree files from Linux kernel
version 5.11-rc7.
This is in preparation for converting the mx51evk_defconfig
target to driver model.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The micro SD card slot uses GPIO3_13 as card detect pin, so describe
it in the devicetree.
This was noticed when converting imx53-qsb board to driver model
in U-Boot as the micro SD card was not getting detected.
After this change it is possible to load the dtb and zImage
from the SD card and boot Linux.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Make the conversion to driver model as it is mandatory.
Remove the SATA support for now as the i.MX53 support has not
been added yet.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Import the imx53-qsb devicetree files from Linux kernel
version 5.11-rc7.
This is in preparation for converting the mx53loco_defconfig
target to driver model.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The RGMII link delays can be set on either MAC or PHY side. Set the
rgmii-id PHY mode for FEC and remove FEC_ENET_ENABLE_.XC_DELAY
setting, so that these definitions aren't used anymore throughout
the U-Boot.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
- Enable uefi related commands for STMicroelectronics STM32MP15 boards
- Remove duplicate uart nodes in stm32mp15 device tree
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAmA5DRwACgkQ4rK92eCq
k3WKtQf+Nk2N8XzhKgoz4dfg+A/uZ1ppKiuuYfHWitvw9OLrjGO61MnYOc6Dh7De
LchPExBYnatj3lxu3IEaaNUGJRujnt9n3W8JNQTGB81MI1TO2oITEhAyDqpMGtqt
pvr1NaoxhZM4B7n/HoQnVB+XtlP08w45SQiEXjjaO82hWRk45sAZ7WGFSs60iVck
ocqhrJ/2AraG98JQPxWfvdqr+24gl1Gt++KT/cdHS//IeYJJYuiCD3m9vOj8TatH
gDVbfR6tquZ5HLvKr/orRz3smaCuutWdHcDwcjs3kFK1rBHSYFZhG3qHQ3ZqNm+w
T/7JIqz4W366o7QZXXlCoi56w2tpug==
=f/Cg
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210226' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Add USB host boot support in stm32mp1 config
- Enable uefi related commands for STMicroelectronics STM32MP15 boards
- Remove duplicate uart nodes in stm32mp15 device tree
Remove duplicated uart nodes introduced with commit 62f95af92a
("ARM: dts: stm32mp1: DT alignment with Linux kernel v5.9-rc4"),
because the uart nodes wasn't correctly ordered in alphabetic order.
Only cosmetic: the generated device tree don't change.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The SPI NOR flash node name in main device tree for Turris Omnia is
called `spi-nor@0`.
Rename node spi-flash@0 in Turris Omnia's -u-boot.dtsi file to spi-nor@0
so that U-Boot does not try to probe the same SPI NOR device multiple
times.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
The commit 6337d53fdf ("arm: dts: sync am33xx with Linux 5.9-rc7")
synchronized the am33xx-clocks.dtsi file with Linux 5.9-rc7 with the
exception of two nodes. I think I was wrong and it is better to keep
the two files similar and possibly make changes to the *-u-boot.dtsi
files.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
The definition follows the DSA binding in kernel and describes the switch,
its ports and PHYs. The switch node has the same structure as in Linux
and this patch enables it (and relevant ports) for the LS1028A RDB board.
ENETC PF6 is the 2nd Eth controller linked to the switch on LS1028A, it is
not used in U-Boot and was disabled. Ethernet port aliases were also
added to better manage the multitude of ports available now.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Move gpio controller nodes from am33xx.dtsi to am33xx-l4.dtsi. Now both
files are more similar to those found in Linux 5.9-rc7. To be fully
operational as before it was also necessary to fix the am33xx-clock.dtsi
file. It too is now almost the same as the Linux kernel.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Since commit 6239cc8c4e ("arm: dts: k3-j7200: Sync Linux v5.11-rc6 dts
into U-Boot") ranges have been added to CPSW node which results in
U-Boot CPSW driver failing to acquire phy_gmii_sel register range and
thus failing to configure GMII mode correctly.
Fix this by deleting ranges in -u-boot-dtsi just like its done for other
K3 platforms.
Fixes: 6239cc8c4e ("arm: dts: k3-j7200: Sync Linux v5.11-rc6 dts into U-Boot")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
This board has not been converted to CONFIG_DM_MMC by the deadline of
v2019.04, which is almost two years ago. In addition there are other DM
migrations it is also missing. Remove it.
Cc: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Chris Packham <judge.packham@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmAmOowcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyGEpB/oD2ZQdqY/kfu0SlKE6
2Qor+MSwDA8yQlAKfiX2J3x0sAaGNkeUPQrWLxutACd34MJsjG41sr6uvLwu4E9f
bc91Gk1Xv/kmySi7JPfpctb01Bd1GVpzuHELIumGgYRkNSwAFFaXrqVPxr/9cN3t
dEcfbKX0p4qXUv/TDw3tE1D63dYPIJC3yX0/4n/n824AKeqRyTMVC34rjfEOoE/r
0w6YSxwQ8hlh23xwc2tyEMSKR4jNp8mAtQcl03Gi/6xiaqgH6lQ6ardSblr3qvjW
6Ev1nd3f9d8i0CzipbLH6PL4G31Ft+ZG/Z/z8wqA6w15h29wu7CfV8yC0aBV0g0/
N1ko
=7ddr
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2021.04-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel fixes for 2021.04 cycle:
This small PR includes just two fixes but very important: one revert in
the clk subsystem which fixes the boot on many old boards
(sama5d2_xplained, sama5d4_xplained), which currently crash at boot; and
one small fix related to debug serial on sama7g5ek board.
If the serial tx/rx are floating, it can happen that bogus characters
are detected on the line at boot time. This leads to U-boot accidentally
thinking someone pressed a key to stop autoboot, thus stopping booting process.
This can happen if the serial cable is not connected. There are hardware
pull-ups on the board connected to serial cable VBUS.
To solve this when the cable is not plugged, enable internal pull-ups as well
for the tx/rx lines.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
The Linux kernel v5.7-rc1 introduced the compatible "st,stm32mp15-hsotg".
See Linux kernel commit d49850110434 ("dt-bindings: usb: dwc2: add
support for STM32MP15 SoCs USB OTG HS and FS")
This patch updates the supported compatible in DWC2 driver,
removes the add-on done in U-Boot dtsi and keeps the compatible
defined in SOC dtsi arch/arm/dts/stm32mp151.dtsi:
usbotg_hs: usb-otg@49000000 {
compatible = "st,stm32mp15-hsotg", "snps,dwc2";
reg = <0x49000000 0x10000>;
...
};
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Use the ADC channel 1 to check the hardware revision of the board and
detect the N2 vs. N2+ and the C4 vs. HC4 variants. Each of them use
different dtb file, so adjust fdtfile environment variable to the
detected variant.
The ADC min/max values for each variant are taken from the vendor code,
adjusted to the 12-bit ADC driver operation mode (vendor code use 10-bit
mode).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Device tree alignment with Linux kernel v5.11-rc2
- fix DCMI DMA features on stm32mp15 family
- Add alternate pinmux for FMC EBI bus
- Harmonize EHCI/OHCI DT nodes name on stm32mp15
- update sdmmc IP version for STM32MP15
- Add LP timer irqs on stm32mp151
- Add LP timer wakeup-source on stm32mp151
- enable HASH by default on stm32mp15
- enable CRC1 by default on stm32mp15
- enable CRYP by default on stm32mp15
- set bus-type in DCMI endpoint for stm32mp157c-ev1 board
- reorder spi4 within stm32mp15-pinctrl
- add STUSB1600 Type-C using I2C4 on stm32mp15xx-dkx
- fix mdma1 clients channel priority level on stm32mp151
- fix dmamux reg property on stm32mp151
- adjust USB OTG gadget fifo sizes in stm32mp151
- update stm32mp151 for remote proc synchronization support
- support child mfd cells for the stm32mp1 TAMP syscon
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The kilohertz unit abbreviation should read 'kHz'.
Note to STM32 team: modified files were generated, it may be worth
to fix STM32CubeMX tool.
Signed-off-by: Fabrice GIRARDOT <fabrice.girardot@flowbird.group>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Enable SATA support. Although not supported by the usual SATA pins on
the SMARC baseboard connector, SATA mode is supported on a PCIe lane.
This way one can use a mSATA card in a Mini PCI slot.
We need to invert the received data because in this mode the polarity of
the SerDes lane is swapped. Provide a fixup in board_early_init_f() for
the SPL. board_early_init_f() is then not common between SPL and u-boot
proper anymore, thus common.c is removed, as it just contained said
function.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Although this variant has two external network ports, they are not (yet)
supported by the bootloader because they are connected via an internal
network switch. Otherwise its the same as the other variants.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This variant has one network port connected via RGMII and doesn't have
any TSN capabilities out-of-the-box. Instead it has all four SerDes
lanes available for customer use.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The variants differ in their network configuration. Move the first two
network aliases to the proper variant device tree includes. This is in
prepartion for variant 1 and 2 support which has a different network
port mapping. The network aliases for the two internal ports will stay
in the common dtsi because they are present on all board variants.
This might leave a hole if there is no ethernet1 alias. This is
intended.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The Beacon EmbeddedWorks kit is based on the R8A774E1 SoC also
known as the RZ/G2H.
The kit consists of a SOM + Baseboard and supports microSD,
eMMC, Ethernet, a couple celular radios, two CAN interfaces,
Bluetooth and WiFi. It shares much of the same design as
the RZ/G2M and RZ/G2N dev kits.
Signed-off-by: Adam Ford <aford173@gmail.com>
The Beacon EmbeddedWorks kit is based on the R8A774B1 SoC also
known as the RZ/G2N.
The kit consists of a SOM + Baseboard and supports microSD,
eMMC, Ethernet, a couple celular radios, two CAN interfaces,
Bluetooth and WiFi. It shares much of the same design as
the RZ/G2M dev kit.
Signed-off-by: Adam Ford <aford173@gmail.com>
Sync all J7200 related v5.11-rc6 Linux kernel dts into U-Boot.
MCU R5F nodes are not yet added in Linux kernel yet but were added
in U-Boot. In order to avoid regressions, r5f nodes are kept intact.
These will be added in kernel in future.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Sync all J721e related v5.11-rc6 Linux kernel dts into U-Boot.
HBMC nodes are not yet added in Linux kernel yet but were added
in U-Boot. In order to avoid any regressions, hbmc nodes are kept
intact. These will be added in kernel in future.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
There's an issue with the base board in which the power cycle
circuit takes way longer to power down than expected by mmc core.
code. This prevents the card from enumerating in UHS modes.
Disable UHS modes for this board until a new board revision fixes
the issue.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Add the appropriate itapdly and clkbuf-sel values required for
some lower speed modes.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Add support for UHS modes by adding the regulators to power cycle
and voltage switch the card. Also add pinmuxes required for each
node
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Add support for regulators to power cycle and switch IO voltage to the
SD card. This enables support for UHS modes.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Update otap delay values to match with the latest Data Manual[1].
[1] https://www.ti.com/lit/gpn/dra829v
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Because of fundamental interface issues in am65x pg1, only the
initial sdhci1 node at 25 MHz was added in the u-boot.dtsi
from which both the base-board.dts and r5-base-board.dts
inherit the node. Move the node out to k3-am65-main.dtsi
where it belongs and add the board specific properties
in base-board.dts and r5-base-board.dts
This ensures dts compatibility with the kernel dts in the
base-board.dts and enables the SD card interface at 50 MHz
and High Speed mode
While we are here, also fix the main_mmc0_pins_default
property to be included and inherit from the base-board.dts
instead of the u-boot.dtsi
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
The K3 R5F remoteproc driver in U-Boot was upstreamed prior to the
equivalent remoteproc driver in the Linux kernel. Some of the DT
properties used in U-Boot got upstreamed using different names
in Linux kernel.
The modified property names include the R5F cluster mode configuration
property "lockstep-mode"; and three different individual R5F core config
properties - "atcm-enable", "btcm-enable" and "loczrama". The property
names were updated as follows:
lockstep-mode => ti,cluster-mode
atcm-enable => ti,atcm-enable
btcm-enable => ti,btcm-enable
loczrama => ti,loczrama
Update the K3 R5F remoteproc driver, the corresponding binding, and
all the existing usage in AM65x, J721E and J7200 dts files all at
once to use the new properties and to not break any bisectability.
Signed-off-by: Suman Anna <s-anna@ti.com>
DTS files apart from r8a774a1-hihope-rzg2m-u-boot.dts and
r8a774a1-u-boot.dtsi have been imported from linux 5.10
commit 2c85ebc57b3e1817 ("Linux 5.10").
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
1. Enable MTK SPI NOR controller driver on mt7622 & mt7629.
2. Enable quad mode for read and single mode for write.
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
- Espressobin: Disable slot when emmc is not present (Pali)
- DS414; config header cleanup (Phil)
- PCI: auto-config enhancement (Phil)
- pci_mvebu: Also map IO region (Phil)
- serial: a3720: Implement pending method for output direction (Pali)
- turris_mox: Enable a few commands (Marek)
- helios4 & ClearFog changes (Dennis)
- Plus some minor misc changes
Add CAxxxx Ethernet support for the Cortina Access
Presidio Engineering Board
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Tom Rini <trini@konsulko.com>
Move all aliases defintions into the main dts file
Add u-boot definiton to i2c0 based on clearfog
set spi1 status to okay
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
OrangePi Zero2 is SBC based on Allwinner H616 with 1 GiB of RAM, SD card
support, gigabit ethernet, micro HDMI, WIFI, Bluetooth and 1 USB 2.0
port. It also has two GPIO headers which allows further peripherals to
be used.
The devicetree file is taken from v3 of the OrangePi Zero2 Linux
submission [1], which it's not yet merged.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2021-January/632084.html
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This commit introduces H616 DTSI file and dt-bindings headers needed for
device tree files.
Files are taken from v3 Linux H616 support submission[1], as the
H616 .dtsi file is not merged upstream yet.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2021-January/632082.html
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
H616 is very similar to H6 so most of the infrastructure can be reused.
However, two big differences are that it doesn't have functional SRAM A2
which is usually used for TF-A and it doesn't have ARISC co-processor.
It also needs bigger SPL size - 48 KiB.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
dts file is taken from Linux 5.11-rc1 tag.
The Bluetooth controller of this device ships with a default address,
use the new CONFIG_FIXUP_BDADDR option to fix it up.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
[Updated OrangePi 3 DT, rebase and config update]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This commit adds support for Tanix TX6 TV box, based on H6. It's low end
H6 board, with 3 GiB of RAM, eMMC, fast ethernet, USB, IR and other
peripherals.
DT file is taken from Linux 5.11-rc1 release.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Updated H6 DT files are based on Linux 5.11-rc1 release.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmAOkP8cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKedCACiDHgP71VKSOiYnEU4
vHD/ANmfMXqnsL71PpSdagnBRAl4vpm46CnD+Mq7RtchxGDNufX6tWJSI04Ci0bC
mfmIfVEjePOnuUayylJ55OlrtJVpBqJFPqxM6MFcIF7nRja1r5thV1jTLNu+b4sm
gg2sk1mC/531Lxbk8S7x+diPymNRArEm3IEw+xEqUhsNVQCKjOEcxi/BWIB2prR3
NxRSGdW3j4CKdBqt7uOL1bqApeQQ9m0/gm1tE3hMXUo09I7uXmb7U52aKb5cV8L+
8ZOlbav6yaPACe3p9npp4K0ByXMmYHjeo1NZW4cvAoKfzragdu0Cv7f0ssVCgrlR
p1e3
=xS6A
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.04-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.04 cycle
This feature set includes macb updates for all interfaces and new
sama7g5 variant support; micrel ksz9031 DLL support; a new board from
Giant based on Adafruit feather form factor which contains a SAMA5D27
SoC; several fixes regarding the NAND flash PMECC block; and pincontrol
drive strength support for pio4 controller.
Beacon EmbeddedWorks is releasing a devkit based on the i.MX8M
Nano SoC consisting of baseboard + SOM.
The kit is based on the same design as the Beacon dev kit with
the i.MX8M Mini.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
In order to support the QSPI chip on the SOM, the Flexspi bus
needs to be configured to talk with the SPI chip.
Resync the som device tree with 5.11-rc4
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
This patch converts the dart6ul ethernet support to DM_ETH and cleans
up the legacy ethernet code. The clean up, more specifically:
* moves the fec2 node and pin definition to the carrier board DTS
since the phy associated with it is on the carrier board and not on
the SoM;
* add the reset pin associated to each phy;
* separate the ethernet, mdio and reset pins of each fec so that they
are easier to reference;
* add clock properties to the phy nodes since they are connected to the
50Mhz ENET[12]_TX_CLK clock of the SoC;
* remove CONFIG_BOARD_EARLY_INIT_F since the function is now empty.
Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
Giant board is a tiny SBC based on the Adafruit Feather form factor,
created by groboards it contains a SAMA5D2 processor (SAMA5D27),
128 MB of RAM and a microSD card for storage.
Signed-off-by: Greg Gallagher <greg@embeddedgreg.com>
This adds support for the NanoPi R2S from FriendlyArm.
Rockchip RK3328 SoC
1GB DDR4 RAM
Gigabit Ethernet (WAN)
Gigabit Ethernet (USB3) (LAN)
USB 2.0 Host Port
MicroSD slot
Reset button
WAN - LAN - SYS LED
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
The rng is embedded in the SoC so enable it in the device tree
universally, the use of it can be controlled by enabling/disabling
at the device config level.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
SPI flash on this machine is located on bus 1, default to using bus 1
for SPI flash and stop aliasing it to bus 0. Formerly the alias spi1
pointed to &spi5, use an alias spi5 for this instead.
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Suggested-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
SPI flash on this board is located on bus 1, default to using bus 1 for
SPI flash on both rk3399-roc-pc and -mezzanine, and stop aliasing it to
bus 0.
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Suggested-by: Simon Glass <sjg@chromium.org>
Fixes: c4cea2bb ("rockchip: Enable building a SPI ROM image on bob")
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
AST2600 is the 7th generation of Aspeed SoC designated for
Interated Remote Management Processor.
AST2600 has significant performance improvement by integrating
1.2GHz dual-core ARM Cortex A7 (r0p5) CPU with FPU. Most of the
controllers are also improved with more features and better
performance than preceding AST24xx/AST25xx.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Set environment for Nand flash (U-boot 2020.04):
- add nand flash in the device tree
- add new default configuration file for G3 using parallel Nand
- set nand parameters in presidio_asic.h
Signed-off-by: Kate Liu <kate.liu@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Remove the leading "0x" from rpc node to fix the below dtc warning:
Warning (simple_bus_reg): Node /soc/rpc@0xee200000 simple-bus unit
address format error, expected "ee200000"
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Add binman node to device tree to generate the FIT image for u-boot
(u-boot.itb) and OS kernel (kernel.itb).
u-boot.itb contains arm trusted firmware (ATF), u-boot proper and
u-boot device tree for ATF u-boot flow.
kernel.itb contains Linux Image and Linux device tree.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
- Update MAINTAINERS emails for STI and STM32
- Activate OF_LIVE for ST stm32mp15 boards
- Switch to MCO2 for PHY 50 MHz clock for DHCOM boards
- Correction in stm32prog command on uart: always flush DFU on start command
- Update USB-C power detection algorithm on DK boards
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl/+yLkACgkQ4rK92eCq
k3X/Fgf/d/11WyQrVzvpr+nN+4Wl7J+ASmoUz0yKa6ri+lbvhLgh+JXbCRKgRPWu
vNnI07pSoX/QeaMpGBU8Ztg/Onb9/pvffz4WMk1411GoyCpDFuuK3cVSIoqkPfu+
XmgSX0u4BXtve1+ZdWfVBWXawUSEDMmGR3tmz1708c/s/oYpnVeRDcqiqzJ94cWE
yt+SpMPVqMUVQ/rAGkE8ToSMxX7FusEa7SvCg4U2ikoRWs3kPpr/73+tRWlmgGxL
sW8SXSKiOmFyheSBx3d2B9n00kDYTTrQmbW9hlMilZmji7CwZYxgTCMdX0x4DeFP
RDajT2Yju1JmeM+Z8+Ke2tupzvy6QA==
=oK8C
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210113' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Enable logging features for stm32mp15 boards
- Update MAINTAINERS emails for STI and STM32
- Activate OF_LIVE for ST stm32mp15 boards
- Switch to MCO2 for PHY 50 MHz clock for DHCOM boards
- Correction in stm32prog command on uart: always flush DFU on start command
- Update USB-C power detection algorithm on DK boards
A previous series already update STMicroelectronics emails maintainers
but some files have been omitted (Makefile, .dts, .dtsi and .rst files).
Update Patrick and my email address with the one dedicated to upstream
activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The LAN8710i PHY currently uses 50 MHz clock direct from PLL4P.
To permit PLL4P to run at faster frequency, use MCO2 as a divider.
The PLL4P runs at 100 MHz, supplies MCO2 which divides it by 2 to
50MHz, and supplies the PHY with 50 MHz via pin PG2. The feedback
clock are fed back in via pin PA1.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Change-Id: Ia9bf7119785d49b633a3ae761c3dc4a30b92628a
- DM support for OMAP PWM backlight
- USB host mode support for AM654
- Minor SPI fixes
- Add support k2g ice board with 1GHz silicon
- Fix GTC programming for K3 devices
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl/8S/0cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKFkB/9NBJq/+sgHZXRaMlAu
ULNwOPoNsQxHQGwF88B1lC+H8LJjM+2gJ8MfJdWvHNlcSdtJjbWk0aQL+5LKSlyz
G7l3BZ+AIYMOeTXay5mNUKnekXIr7c8tLoX8FH/Ih+bHFPt57qL0bbfznV66UCOp
/o/yM8daPa9Kx1vPEpT2dC9bYXLXeQv6R+RMxwoc4Bk+R3OK7zoZ3Wdx0q9HvBwj
iWHM49X2fBqqi5RS+ZI37AUzi8iysD3fOq0kWTJcCNaci8i8RZdzSyoaDuXhA63I
EZJ7v9fUkW/bwTONVE9n2BX4xF9X/6R7P46l9dQISXAxsOBwsNRQPt8Ro7mCoc4K
392o
=LIK7
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.04-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features for 2021.04 cycle
This feature set includes the new board SAMA7G5 EK, the new evaluation
kit for Microchip AT91 SAMA7G5 SoC . The current board support includes
two configurations for booting from eMMC (SDMMC0), SD-Card (SDMMC1), and
support for two Ethernet interfaces.
The previous version of am335x-fb.c contained the functionalities of two
drivers that this patch has split. It was a video type driver that used
the same registration compatible string that now registers a panel type
driver. The proof of this is that two compatible strings were referred
to within the same driver.
There are now two drivers, each with its own compatible string,
functions and API.
Furthermore, the panel driver, in addition to decoding the display
timings, is now also able to manage the backlight.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
There have been several changes to the am33xx.dtsi, so this patch
re-syncs it with Linux.
Let's add proper interconnect hierarchy for l4 interconnect instances
with the related ti-sysc interconnect module data as documented in
Documentation/devicetree/bindings/bus/ti-sysc.txt of the Linux kernel.
With l4 interconnect hierarchy and ti-sysc interconnect target module
data in place, we can simply move all the related child devices to their
proper location and enable probing using ti-sysc.
The am33xx-clock.dtsi file is the same as that of the Linux kernel,
except for the reg property of the node l4-wkup-clkctrl@0.
As for the am33xx.dtsi file, all the devices with drivers not yet
implemented and those I was able to test with this patch have been moved
to am33xx-l4.dtsi. In case of any regressions, problem devices can be
reverted by moving them back and removing the related interconnect
target module node.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Update the ddr settings to use the DDR reg config tool rev 0.5.0.
This enables 4266MTs DDR configuration.
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Kevin Scholz <k-scholz@ti.com>
The sequence number assigned for USB subsystem in a uclass is dependent on
the order of occurrence in the device tree. If the dr_mode of USB3SS0
controller is varied then the sequence number of USB3SS1 controller also
changes. If aliases are added then sequence numbers are assigned using the
alias number. This makes the sequence number of USB3SS1 controller
independent of USB3SS0 controller's dr_mode.
Therefore, add aliases to fix the sequence number assigned to the USB
subsystems.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
PineCube is an IP camera development kit released by Pine64.
It comes with the following compoents:
- A mainboard with Sochip S3 SoC, a 16MByte SPI Flash, AXP209 PMIC,
a power-only microUSB connector, a USB Type-A connector, a 10/100Mbps
Ethernet port and FPC connectors for camera and daughter board.
- An OV5640-based camera module which is connected to the parallel CSI
bus of the mainboard.
- A daughterboard with several buttons, a SD slot, some IR LEDs, a
microphone and a speaker connector.
As the device tree is synchronized in a previous commit, just add it to
Makefile, create a new MAINTAINER item and provide a defconfig.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Import the Beelink GT-King/Pro and supporting meson-g12b-w400.dtsi file
from Linux 5.10.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Import the WeTek Core2 and supporting meson-gx-p23x-q20x.dtsi files
from Linux 5.10.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add support for the Amlogic based libretech cc version 2.
As version 1, it is based on the s905x SoC.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[narmstrong: Fixed libretech-cc.rst bullet points]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Sync the libretech cc v2 device tree from Linux v5.10-rc1
commit 3650b228f83a ("Linux 5.10-rc1")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
SPI flash on this machine is located on bus 1, default to using bus 1
for SPI flash and stop aliasing it to bus 0.
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Suggested-by: Simon Glass <sjg@chromium.org>
Fixes: c4cea2bb ("rockchip: Enable building a SPI ROM image on bob")
TXC line is directly connected from the SoC to the KSZ9131 PHY. There
is a transient state on this signal, before configuring it to RGMII,
which leads to packet transmit being blocked.
Keeping a pull-up when muxing this pin as function A (G0_TXCK) fixes
the issue.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Add node for flx1 i2c1 subnode (and alias to bus 0)
This bus has two eeprom devices connected.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Enable sdmmc0 on this board. A non-removable eMMC is connected on this
block.
Configure pincontrol accordingly.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
SDMMC1 requires clock specification with assigned-clocks, such that
the PMC will know which parent to assign and the initial start-up frequency.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Get rid of software defined MCK and switch to PMC bindings
for IPs currently present in device tree.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
arm64:
- DT updates
microblaze:
- Add support for NOR device support
spi:
- Fix unaligned data write issue
nand:
- Minor code change
xilinx:
- Fru fix in limit calculation
- Fill git repo link for all Xilinx boards
video:
- Add support for seps525 spi display
tools:
- Minor Vitis file support
cmd/common
- Minor code indentation fixes
serial:
- Uartlite debug uart initialization fix
-----BEGIN PGP SIGNATURE-----
iFsEABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX/ROlgAKCRDKSWXLKUoM
IRC5AIkBzg4Sz8fQgdCiOK89k7tdFKMAnA9SYhgm4TSCzffZCJwnm78QoGAC
=4FnY
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.04
arm64:
- DT updates
microblaze:
- Add support for NOR device support
spi:
- Fix unaligned data write issue
nand:
- Minor code change
xilinx:
- Fru fix in limit calculation
- Fill git repo link for all Xilinx boards
video:
- Add support for seps525 spi display
tools:
- Minor Vitis file support
cmd/common
- Minor code indentation fixes
serial:
- Uartlite debug uart initialization fix
The GPIO hog flags are ignored by gpiolib-of.c now, set the flags to 0.
Since GPIO_ACTIVE_HIGH is defined as 0, this change only increases the
correctness of the DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The GPIO hog flags are ignored by gpiolib-of.c now, set the flags to 0.
Due to a change in gpiolib-of.c, setting flags to GPIO_ACTIVE_LOW and
using output-low DT property leads to the GPIO being set high instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This patch add ethernet node gem1 to zcu1285 RevB.
GMII to RGMII converter sits between MAC and external
phy connected over GMII to MAC and RGMMI to external phy
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch add ethernet node gem1 to zcu1275 RevB.
GMII to RGMII converter sits between MAC and external
phy connected over GMII to MAC and RGMMI to external phy.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
For correct spi bus detection the spi0 alias is needed in the DT.
Otherwise this error will ocurr in U-Boot:
Invalid bus 0 (err=-19)
Failed to initialize SPI flash at 0:0 (error -19)
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dennis Gilmore <dgilmore@redhat.com>
Tested-by: Dennis Gilmore <dgilmore@redhat.com>
Add some missing "u-boot,dm-pre-reloc;" properties to UART0, SPI
controller and SPI NOR flash node to enable usage in SPL. Otherwise
these devices will not be available.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dennis Gilmore <dgilmore@redhat.com>
Tested-by: Dennis Gilmore <dgilmore@redhat.com>
The dart6ul has an i2c eeprom at 0x50 which contains, among other
things, the manufacturing/revision/options info of the SoM. This patch
replaces the current checkboard() implementation with a more
exhaustive one based on the content of the eeprom.
Since this code uses the new driver model, some changes were also
required in the DTS to make the nodes related to i2c available before
relocation.
This code was inspired from the supported u-boot code from Variscite
which can be found here:
https://github.com/varigit/uboot-imx/tree/imx_v2018.03_4.14.78_1.0.0_ga_var02
New output example:
Board: PN: VSM-6UL-705B, Assy: AS1812142257, Date: 2019 Feb 17
Storage: eMMC, Wifi: yes, DDR: 1024 MiB, Rev: 2.4G
Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The eeprom at address 0x50 is a BR24G04NUX-3TTR. It has a
4Kbit (512x8) capacity, change the compatible string to reflect this
fact.
Also, add an alias to easily refer to this eeprom with
fdt_path_offset() which will be in another commit.
Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The current PHY rework does the following things:
1. Configure 125MHz clock
2. Setup the TX clock delay (RX is enabled by default),
3. Setup reserved bits to avoid voltage peak
The clock delays are nowadays already configured by the
PHY driver (in ar803x_delay_config). The code for that
can simply be dropped. The clock speed can also be
configured by the PHY driver by adding the device tree
property "qca,clk-out-frequency".
What is left is setting up the undocumented reserved bits
to avoid the voltage peak problem. I slightly improved its
documentation while updating the board's PHY rework code.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
i.MX8M series provide support for high speed grades in their
usdhc controllers, which has eMMC and SDHC connected to them.
Enable this support across the entire i.MX8M family by providing quirks
to usdhc controllers designated by storage media connected to them.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Some SD Card controller and power circuitry has increased capacitance,
which keeps the internal logic remains powered after regulator is switch
off. This is generally the case when card is switched to SD104 mode,
where a power cycle should be performed. In case if the card internal
logic remains powered, it causes a subsequent failure of mode
transition, effectively leading to failed enumeration.
Introduce a delay of 20 msec in order to provide a possibility for
internal card circuitry to drain voltages and perform a power cycle
correctly.
Similar fix is done in commit c49d0ac38a ("ARM: dts: rmobile: Increase
off-on delay on the SD Vcc regulator") targeted Renesas SOCs.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
There have been some updates to the device tree since 5.6.
This also includes some clocks, and makes it easier to keep
board device tree files in sync with Linux
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Fixed wrong PHY Interface Mode
As per kernel commit 0672d22a1924 ("ARM: dts: imx: Fix the AR803X phy-mode)
the correct phy-mode should be "rgmii-id", so fix it accordingly
to fix the Ethernet regression.
This problem has been exposed by commit:
commit 13114f38e2
Fix the phy-mode accordingly to fix the regression.
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Since linux commit 2e6cde96873253fd9eb0f20afd8ffd18278cff75 ("arm64:
dts: ls1028a: make the eMMC and SD card controllers use fixed indices")
mmc0 is the eMMC and mmc1 is the SD card. Also swap it in u-boot to
avoid any confusion by the user and to be aligned with linux.
Signed-off-by: Michael Walle <michael@walle.cc>
For the proper reboot Odroid-C4 board requires to switch TFLASH_VDD_EN
pin to the high impedance mode, otherwise the board is stuck in the
middle of loading early stages of the bootloader from SD card.
This can be achieved by using the OPEN_DRAIN flag instead if the
ACTIVE_HIGH, what will leave the pin in input to achieve high state (pin
has the pull-up) and solve the issue.
Suggested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This adds SoC-specific compatible strings to all users of the designware
spi device. This will allow for the correct driver to be selected for each
device. Where it is publicly documented, a compatible string for the
specific device version has also been added. Devices without
publicly-documented device versions include MSCC SoCs, and Arc Socs. All
compatible strings except those for SoCFPGAs and some of the versioned
strings have been taken from Linux.
Since SSI_MAX_XFER_SIZE is determined at runtime, this is not strictly
necessary. However, it is a good cleanup and brings things closer to Linux.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl/TlVUcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyK8eB/9mIJCgCiDue2ytkUg+
fyJHHtHf+rFIbvLiR+iVy/2rXlsjfXwNVyJTswJOCucit0cf+F7fh6vi/AnOoDnE
Zezj9ngm+25fvffQjt0T74V2w+GhT5OXqR7ctpIcrmKun2UTujSA9NQqRaLFDI9x
RQlUXsCzLypFZRXvyOCo34Nz7MZ1QvIAKxEJyYb7ft/qnbtILDr0p54xxjlK5B/W
s+MP05qaRmup9rk33JwfLmeyjTmDBuri0rBh/2XKFtszJBm5CdgXJEqNY+22JzJF
xlqfobmdPn77+JH36B/KJgDmrrL05vv+RyvOPoBNzm6BEKtlflcSf9NnTKlSud4y
w/50
=r687
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2021.01-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel fixes for 2021.01 cycle
This set includes very important fixes for: MMC booting on several
boards, drive strength on sam9x60ek mmc lines, compile issues for
timer.c old driver, removal of unwanted access to sam9x60 bit for
oscillator bypass mode, and eeproms read on sama5d2_icp.
The correct compatible for this eeproms is microchip,24aa02e48
The previous compatible string was working up to U-boot 2020.04.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Tested-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Add label to pcie nodes in dts so that these nodes
are easy to refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add label to pcie nodes in dts so that these nodes
are easy to refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add label to pcie nodes in dts so that these nodes
are easy to refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add label to pcie nodes in dts so that these nodes
are easy to refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add label to pcie nodes in dts so that these nodes
are easy to refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add label to pcie nodes in dts so that these nodes
are easy to refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add label to pcie nodes in dts so that these nodes
are easy to refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
- Update ARM STI and ARM STM STM32MP Arch maintainers emails
- Enable internal pull-ups for SDMMC1 on DHCOM SoM
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl/Q5aAACgkQ4rK92eCq
k3XuqAgAifJcb3NxKmWa4eFDbZpWZ1R8h6FPp6vlmvyC4C3otRHEe5WrYCsAeqy1
Gs311dtdluc4y5Ltmf54OcN7ICfLsSiOvye85f5myhPj1v4d1F1Z70X0FDo/o9hE
7TEZfWBQtNjXI4F23+vaDT4jCvUZV1LR6Lab/zLLw1/uLUxxS799kcFiWgHLuEoH
8Cv0JbgzLuuVk5lyLJ+DFZOcntwWu5+Qm+l5eS46armbKphMFh5KPJ9PG81eJE3N
zsCpavEs4nuQl7wGF8HPfDWxz5Xef6ip3A4Owh92t3WQWKxp1bSUKqDeKZTkhIyS
LSJKe9CQ9+zCS3m3Utoi1pVt1EbFrQ==
=cgbE
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20201209' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Manage CONFIG_ENV_EXT4_DEVICE_AND_PART in stm32mp1 board
- Update ARM STI and ARM STM STM32MP Arch maintainers emails
- Enable internal pull-ups for SDMMC1 on DHCOM SoM
Add USB OTG ID pin mux and switch the USB OTG port
from peripheral to OTG mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The DH DRC02 board has an on-board microSD slot,
add DT properties to enable the slot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The STM32MP1 DHCOM SoM can be built with either bus voltage level shifter
or without one on the SDMMC1 interface. Because the SDMMC1 interface is
limited to 50 MHz and hence SD high-speed anyway, disable the SD feedback
clock to permit operation of the same U-Boot image on both SoM with and
without voltage level shifter.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The default state of SD bus and clock line is logical HI. SD card IO is
open-drain and pulls the bus lines LO. Always enable the SD bus pull ups
to guarantee this behavior on DHCOM SoM. Note that on SoMs with SD bus
voltage level shifter, the pull ups are built into the level shifter,
however that has no negative impact.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
To simplify setup, configuration and compilation of u-boot, define emmc
node for all Espressobin boards. Espressobin boards without populated emmc
works correctly, just detection and initialization of emmc obviously fails.
Code for emmc is extracted from commit f1a43c84a9 ("arm64: dts: a3720:
add support for espressobin with populated emmc").
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Gérald Kerma <gerald@gk2.net>
Introduce initial hierarchy of device trees for Apalis iMX8X
System on Module.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
The used PMIC has been changed from RHOM BD71837 to NXP PCA9450A.
Adjust the device tree accordingly.
Remove the old ADC node as the ADC has been changed and has no longer
a separate power rail.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reduce vital product data size to match the latest specification.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Removed aristainetos2, 2b, 2b-csl. This boards have been
recalled and destroyed.
Adapt board code to remove stuff not needed anymore.
Fix checkpatch warning, remove fdt_high and initrd_high
from default environment.
Signed-off-by: Heiko Schocher <hs@denx.de>
zu remove
Align the pin setup for sdhci0 with linux kernel.
This means to have slew rate enable and high drive strength.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Use the reset function to handle the hold boot bit in RCC
with device tree handle with MCU_HOLD_BOOT identifier.
This generic reset allows to remove the two specific properties:
- st,syscfg-holdboot
- st,syscfg-tz
This patch prepares alignment with kernel device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Fabien DESSENNE <fabien.dessenne@st.com>
Cc: Arnaud POULIQUEN <arnaud.pouliquen@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The QSPI CS2 is not used on DHCOM, remove the pinmux and flash@1.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The uSD slot card-detect GPIO is connected to PG1, fix it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Add DT for DH PicoITX unit, which is a bare-bones carrier board for
the DHCOM. The board has ethernet port, USB, CAN, LEDs and a custom
board-to-board expansion connector.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Commit 4b2be78ab6 ("time: Fix get_ticks being non-monotonic")
puts in evidence that get_ticks is called before timer initialization.
Fix it by initializing timer before relocation.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Device tree alignment with kernel v5.10-rc1.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Since kernel v4.8-rc1, commit 05b23ebc2bd9 ("ARM: dts: armv7-m: remove skeleton.dtsi include"),
skeleton.dtsi file is no more included.
This synchronization is needed to avoid to get 2 memory node
in DTB file if, in DTS file, memory node is declared with the correct
syntax as following:
memory@90000000 {
device_type = "memory";
reg = <0x90000000 0x800000>;
};
Then in DTB, we will have the 2 memory nodes, which is incorrect and
cause misbehavior during DT parsing by U-boot:
memory {
device_type = "memory";
reg = <0x00 0x00>;
};
memory@90000000 {
device_type = "memory";
reg = <0x90000000 0x800000>;
};
Issue found when synchronizing MCU's STM32 DT from kernel v5.10-rc1.
When using fdtdec_setup_mem_size_base() or fdtdec_setup_memory_banksize()
API, first above memory node is found (with reg = <0x00 0x00>), so
gd->ram_size, gd->ram_base, gd->bd->bi_dram[bank].start and
gd->bd->bi_dram[bank].size are all set to 0 which avoid boards to boot.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
This commit imports device tree files that are related to Allwinner V3
series from Linux commit 3650b228f83a ("Linux 5.10-rc1").
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Import updated device trees from Linux tag v5.9. This picks up new
hardware (PinePhone, PineTab); and it drops the U-Boot specific DTSI
files for the Pinebook and the Teres-I, since the ANX6345 bridge is
now supported upstream.
A couple of headers needed updates for recently-added hardware support.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Commit c4cea2bbf9 ("rockchip: Enable building a SPI ROM image on bob")
added an alias spi1 referring to spi@ff1d0000, however there was already
an alias spi0 referring to the same node in rockpro64's u-boot.dtsi, and
having both aliases present broke booting from SPI flash for this board.
Remove the spi0 alias, set the default bus for SPI flash to 1, and
enable support for numbered aliases in SPL so that it uses the same bus
numbering as U-Boot proper. This fixes booting from U-Boot in SPI flash
on the rockpro64 board.
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Suggested-by: Simon Glass <sjg@chromium.org>
Fixes: c4cea2bbf9 ("rockchip: Enable building a SPI ROM image on bob")
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
In order to enable the Amlogic SM1 MMC controller fix, we need to add a u-boot specific
MMC controller compatible.
This adds a new meson-sm1-u-boot.dtsi and reworks the other -u-boot.dtsi
to use this for SM1 based boards.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
- Add a new SMBIOS parser and enable it when booting from coreboot
- Fix up various driver names to avoid dtoc warnings
- Fully enable ACPI support on Google Chromebook Coral
- Add a way to set SMBIOS properties using the devicetree
- Update existing boards to use devicetree for SMBIOS using a new
default sysinfo driver
Add settings and enable the default sysinfo driver so that these can come
from the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add settings and enable the default sysinfo driver so that these can come
from the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add settings and enable the default sysinfo driver so that these can come
from the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add settings and enable the default sysinfo driver so that these can come
from the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
---------------------
- new boards : GE (new B1x5v2), phytec phyCORE-i.MX8MM
- converted doc to reST
- fixes for verdin-imx8mm (Toradex)
- fixes for i.MX thermal driver
- mx7ulp: Align the PLL_USB frequency
- mx53: primary/secondary bmode
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/741465284
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCX6QsVQ8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76Z29ACfRdzFocIVEOFNm8v5yA1C/FU9q9sAn1kEAot5
vkm2yvDQ7+9vl5G7+ZRn
=rCCX
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20201105' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx for 2021.1
---------------------
- new boards : GE (new B1x5v2), phytec phyCORE-i.MX8MM
- converted doc to reST
- fixes for verdin-imx8mm (Toradex)
- fixes for i.MX thermal driver
- mx7ulp: Align the PLL_USB frequency
- mx53: primary/secondary bmode
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/741465284
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl+frmwcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyP/tCACuq3aixxpR1qzb/Tk6
MnE/Io9ehtq8WfY2M8ks5RK+K5Ezaukh9Edg7YW8j0mvoBZUQ35at8UXanr8XkEx
vk51AkwmTJeckjZ7I8D9m/AIyAU4lVCB/HJp3KRcTdu39bSy+beudg7uinlmvoHP
GSqmGArU58pbHrHi1xVgf8PIbCd52mVPvDu+ghxjKOTPl87WlRCjxelPuMxjLEQ2
8KUuxuXad82S7oRFQz/TDkokf+d8AZVAbOXWqxAnHWNml+qXLWn/oohSQ5+QsYRY
3K2cJFvI3cmAcr9usOX268u0wGd9kDYnQtfym2M8ul70S3pesqUsoiSET9vXq3zL
yu8a
=QSvy
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2021.01-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel fixes for 2021.01 cycle:
This specific feature set includes the patches for DT required to fix
the warnings for newer DTC version (1.6.0+), i2c and spi bus unit
address.
w+arch/arm/dts/.at91sam9260ek.dtb.pre.tmp:119.21-123.7: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/mtd_dataflash@0: SPI bus unit address format error, expected "1"
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
w+arch/arm/dts/.at91sam9260ek.dtb.pre.tmp:119.21-123.7: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/mtd_dataflash@0: SPI bus unit address format error, expected "1"
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
w+arch/arm/dts/sama5d3xmb.dtsi:64.25-83.7: Warning (i2c_bus_reg): /ahb/apb/i2c@f0018000/camera@0x30: I2C bus unit address format error, expected "30"
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
w+arch/arm/dts/.at91sam9g45-gurnard.dtb.pre.tmp:118.21-122.7: Warning (spi_bus_reg): /ahb/apb/spi@fffa4000/mtd_dataflash@0: SPI bus unit address format error, expected "1"
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
w+arch/arm/dts/.at91sam9g25ek.dtb.pre.tmp:28.25-47.7: Warning (i2c_bus_reg): /ahb/apb/i2c@f8010000/camera@0x30: I2C bus unit address format error, expected "30"
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
w+arch/arm/dts/at91sam9g20ek_common.dtsi:100.21-104.7: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/mtd_dataflash@0: SPI bus unit address format error, expected "1"
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
w+arch/arm/dts/.at91sam9g20-taurus.dtb.pre.tmp:79.18-83.4: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/mtd_dataflash@0: SPI bus unit address format error, expected "1"
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
w+arch/arm/dts/.at91sam9261ek.dtb.pre.tmp:124.15-144.7: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/tsc2046@0: SPI bus unit address format error, expected "2"
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
w+arch/arm/dts/.at91-vinco.dtb.pre.tmp:131.18-134.7: Warning (i2c_bus_reg): /ahb/apb/i2c@f8024000/rtc@64: I2C bus unit address format error, expected "32"
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
GE B1x5v2 patient monitor series is similar to the CARESCAPE Monitor
series (GE Bx50). It consists of a carrier PCB used in combination
with a Congatec QMX6 SoM. This adds U-Boot support using device model
everywhere and SPL for memory initialization.
Proper configuration is provided as 'ge_b1x5v2_defconfig' and the
combined image u-boot-with-spi.imx can be flashed directly to 1024
byte offset to /dev/mtdblock0. Alternatively SPL and u-boot.imx can
be loaded separately via USB-OTG using e.g. imx_usb.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
- New PX30 board: Engicam PX30.Core;
- Fix USB HID support for rock960;
- Remove host endianness dependency for rockchip mkimage;
- dts update for rk3288-tinker;
- Enable console MUX for some ROCKPi boards;
- Add config-based ddr selection for px30;
PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
C.TOUCH 2.0 is a general purpose carrier board with capacitive
touch interface support.
PX30.Core needs to mount on top of this Carrier board for creating
complete PX30.Core C.TOUCH 2.0 board.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Engicam C.TOUCH 2.0 is an EDIMM compliant general purpose
carrier board with capacitive touch interface.
Genaral features:
- TFT 10.1" industrial, 1280x800 LVDS display
- Ethernet 10/100
- Wifi/BT
- USB Type A/OTG
- Audio Out
- CAN
- LVDS panel connector
SOM's like PX30.Core needs to mount on top of this Carrier board
for creating complete PX30.Core C.TOUCH 2.0 board.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board from Engicam.
PX30.Core needs to mount on top of this Evaluation board for
creating complete PX30.Core EDIMM2.2 Starter Kit.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
General features:
- Rockchip PX30
- Up to 2GB DDR4
- eMMC 4 GB expandible
- rest of PX30 features
PX30.Core needs to mount on top of Engicam baseboards for creating
complete platform boards.
Possible baseboards are,
- EDIMM2.2
- C.TOUCH 2.0
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Engicam EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board.
Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Mini PCIe
- MIPI CSI
- 2x CAN
- Audio Out
SOM's like PX30.Core needs to mount on top of this Evaluation board
for creating complete PX30.Core EDIMM2.2 Starter Kit.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add chosen node in -u-boot.dtsi for ROCK-Pi N8 board.
This will help to get serial out messages.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
The property reg-shift with the same value is present in the base
device tree already. Remove unnecessary node from rk3288-tinker.dts.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The I2C EEPROM is present on Tinker Board S as well. Move the i2c node
to the shared, U-Boot specific rk3288-tinker-u-boot.dtsi device tree.
Cc: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- Armada 8k: Add NAND support via PXA3xx NAND driver (Baruch)
- Armada 8k: Use ATF serdes init instead of the "old" U-Boot version
(Baruch)
- Minor update to Octeon TX/TX2 defconfig (Stefan)
common:
- Add support for 64bit loadables from SPL
xilinx:
- Update documentation and record ownership
- Enable eeprom board detection based legacy and fru formats
- Add support for FRU format
microblaze:
- Optimize low level ASM code
- Enable SPI/I2C
- Enable distro boot
zynq:
- Add support for Zturn V5
zynqmp:
- Improve silicon detection code
- Enable several kconfig options
- Align DT with the latest state
- Enabling security commands
- Enable and support FPGA loading from SPL
- Optimize xilinx_pm_request() calling
versal:
- Some DTs/Kconfig/defconfig alignments
- Add binding header for clock and power
zynq-sdhci:
- Add support for tap delay programming
zynq-spi/zynq-qspi:
- Use clock framework for getting clocks
xilinx-spi:
- Fix some code issues (unused variables)
serial:
- Check return value from clock functions in pl01x
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX5rH/QAKCRDKSWXLKUoM
IRPAAJ9SvHR3w1qTc5W+Q5CWBUH5wJbNYQCaA4PpqZCdvyu1+nF5luL6JHhbDgw=
=hOd7
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01-v2' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.01-v2
common:
- Add support for 64bit loadables from SPL
xilinx:
- Update documentation and record ownership
- Enable eeprom board detection based legacy and fru formats
- Add support for FRU format
microblaze:
- Optimize low level ASM code
- Enable SPI/I2C
- Enable distro boot
zynq:
- Add support for Zturn V5
zynqmp:
- Improve silicon detection code
- Enable several kconfig options
- Align DT with the latest state
- Enabling security commands
- Enable and support FPGA loading from SPL
- Optimize xilinx_pm_request() calling
versal:
- Some DTs/Kconfig/defconfig alignments
- Add binding header for clock and power
zynq-sdhci:
- Add support for tap delay programming
zynq-spi/zynq-qspi:
- Use clock framework for getting clocks
xilinx-spi:
- Fix some code issues (unused variables)
serial:
- Check return value from clock functions in pl01x
Align node properties to kernel dts node.
The change of compatible property does not affect any currently
supported board.
Keep U-Boot specific nand-enable-arbiter, and num-cs for compatibility
with the current driver.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Align node properties to kernel dts node.
Keep U-Boot specific nand-enable-arbiter, and num-cs for compatibility
with the current driver.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Shmuel Hazan <shmuel.h@siklu.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
For zynqmp qspi, frequencies up to 40MHz will work irrespective
of feedback clock enabled or disabled. If we want higher than
40Mhz the feedback clock should be enabled.
With spi-max-frequency 108MHz it is not working when the feedback
clock is disabled. Change it to 40MHz so that it works irrespective
of feedback clock enabled or disabled.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Acked-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mini u-boot eMMC dt parameters are not in sync with full u-boot dt.
Frequency for eMMC is fixed to 25Mhz. Due to this, mmc multi-block write
commands are failing. Increase frequency to 200Mhz to fix this issue.
Add bus-width = <8>, non-removable and disable-wp properties to the node
as this is eMMC.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Adding Z-turn board V5 to resolve the change between:
"Z-TURNBOARD_schematic.pdf" schematics state version 1 to 4 has Atheros AR8035
"Z-Turn_Board_sch_V15_20160303.pdf" schematics state version 5 has Micrel KSZ9031
At this time the S25FL128SAGNFI003 doesn't work because of bug:
*** Warning - spi_flash_probe_bus_cs() failed, using default environment
zynq-zturn was checked on V5 board, same error.
Maybe Z-turn board have the same problem (board with W25Q128BVFIG).
Signed-off-by: Alexandre GRIVEAUX <agriveaux@deutnet.info>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add basic support for the Kontron SMARC-sAL28 board. This includes just
the bare minimum to be able to bring up the board and boot linux.
For now, the Single and Dual PHY variant is supported. Other variants
will fall back to the basic variant.
In particular, there is no watchdog support for now. This means that you
have to disable the default watchdog, otherwise you'll end up in the
recovery bootloader. See the board README for details.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The System Control Unit (SCU) controller of Aspeed
SoCs provides the reset control for each peripheral.
This patch refactors the reset method to leverage
the SCU reset control. Thus the driver dependency
on watchdog including dedicated WDT API and reset
flag encoding can be eliminated.
The Kconfig description is also updated accordingly.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Since we now have the driver for Qualcomm PRNG HW, lets use it and add the necessary clocks and nodes.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Lets add the necessary DTS node and pinctrl properties for newly added MDIO driver.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Since we have SPI driver for IPQ40xx QUP SPI controller, lets add the necessary nodes, pinctrl and clocks.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
As the ownership is now Hitachi Power Grids, change the license string
and adapt the compatible string in DTS files. For kmeter1.dts we
change it to "keymile,KMETER1" for now, as this is then compliant with
what is submitted to the linux kernel. All other boards don't have
a upstreamed version in linux mainline.
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
CC: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
CC: Heiko Schocher <hs@denx.de>
CC: Marek Vasut <marex@denx.de>
CC: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Allwinner sun50i SoCs contain an OpenRISC 1000 CPU that functions as a
System Control Processor, or SCP. ARM Trusted Firmware (ATF)
communicates with the SCP over SCPI to implement the PSCI system
suspend, shutdown and reset functionality. Currently, SCP firmware is
optional; the system will boot and run without it, but system suspend
will be unavailable.
Since all communication with the SCP is mediated by ATF, the only thing
U-Boot needs to do is load the firmware into SRAM. The SCP firmware
occupies the last 16KiB of SRAM A2, immediately following ATF.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Since commit d879616e9e ("spl: fit: simplify logic for FDT loading for
non-OS boots"), the SPL looks at the "os" properties of FIT images to
determine where to append the FDT.
The "os" property of the "firmware" image also determines how to execute
the next stage of the boot process, as in 1d3790905d ("spl: atf:
introduce spl_invoke_atf and make bl31_entry private"). For this reason,
the next stage must be specified in "firmware", not in "loadables".
To support this additional functionality, and to properly model the boot
process, where ATF runs before U-Boot, add the "os" properties and swap
the firmware/loadable images in the FIT image.
Since this description was copied as an example in commit 70248d6a2916
("binman: Support generating FITs with multiple dtbs"), update those
examples as well for correctness and consistency.
Acked-by: Patrick Wildt <patrick@blueri.se>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This consolidates the SoC-specific part at the top of the file to avoid
cluttering it up with preprocessor conditions.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Prior to commit 7f7f8aca8257 ("sunxi: Convert 64-bit boards to use
binman"), if the BL31 environment variable was not defined, the firmware
would be loaded from a file "bl31.bin" in the current directory. Restore
that behavior by providing that as the default filename in case no entry
arg is provided, which will be the case if the environment variable is
unset.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Nodes should have a blank line separating them from sibling nodes and
properties. Add the necessary lines.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Use slow clock CCF compatible DT bindings. This will not break
the above functionality as the SoC is not booting with current
PMC bindings.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
- fsl_esdhc_imx cleanup
- not send cm13 if send_status is 0.
- Add reinit API
- Add mmc HS400 for fsl_esdhc
- Several cleanup for fsl_esdhc
- Add ADMA2 for sdhci
Import armada-3720-espressobin-emmc.dts from Linux, but use sdhc1 for
emmc, since our dtsi is still based on downstream and sdhc0 is used for
the sd card.
Signed-off-by: Andre Heider <a.heider@gmail.com>
