Make the conversion to driver model as it is mandatory.
Tested booting the Linux kernel from the SD card.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Make the conversion to driver model as it is mandatory.
Remove the SATA support for now as the i.MX53 support has not
been added yet.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. As this is the last ARCH_MPC8569 board, remove that support
as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Use CONFIG_IS_ENABLED() macro, which provides more convenient
way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs
for both SPL and U-Boot proper.
CONFIG_IS_ENABLED(DM_I2C) expands to:
- 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y',
- 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y',
- 0 otherwise.
All occurences were replaced automatically using these bash cmds:
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board has not been converted to CONFIG_DM_MMC by the deadline of
v2019.04, which is almost two years ago. In addition there are other DM
migrations it is also missing. Remove it.
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board has not been converted to CONFIG_DM_MMC by the deadline of
v2019.04, which is almost two years ago. In addition there are other DM
migrations it is also missing. Remove it.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Distro Boot requires a U-Boot-specific script named boot.scr or
boot.scr.uimg which contains boot commands to boot the system. The
boot.cmd is such a file. Use mkimage to generate boot.scr or
boot.scr.uimg from boot.cmd, and the command is:
mkimage -A arm -O linux -T script -C none -a 0 -e 0 -n "Distro Boot Script" -d boot.cmd boot.scr.uimg
The boot.cmd file is an example script and can be modified based on
needs. bootargs is set in this script and root uses the default value
"/dev/mmcblk1p2 rootwait rw" which can be changed by overriding mmcroot.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Distro Boot requires a U-Boot-specific script named boot.scr or
boot.scr.uimg which contains boot commands to boot the system. The
boot.cmd is such a file. Use mkimage to generate boot.scr or
boot.scr.uimg from boot.cmd, and the command is:
mkimage -A arm -O linux -T script -C none -a 0 -e 0 -n "Distro Boot Script" -d boot.cmd boot.scr.uimg
The boot.cmd file is an example script and can be modified based on
needs. bootargs is set in this script and root uses the default value "
/dev/mmcblk1p2 rootwait rw" which can be changed by overriding mmcroot.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
use CONFIG_TARGET_IMX8MN_DDR4_EVK for DDR4 EVK board, we will use
CONFIG_TARGET_IMX8MN_EVK for LPDDR4 EVK board.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
=9kN3
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next
Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
The current macro is a misnomer since it does not declare a device
directly. Instead, it declares driver_info record which U-Boot uses at
runtime to create a device.
The distinction seems somewhat minor most of the time, but is becomes
quite confusing when we actually want to declare a device, with
of-platdata. We are left trying to distinguish between a device which
isn't actually device, and a device that is (perhaps an 'instance'?)
It seems better to rename this macro to describe what it actually is. The
macros is not widely used, since boards should use devicetree to declare
devices.
Rename it to U_BOOT_DRVINFO(), which indicates clearly that this is
declaring a new driver_info record, not a device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Lower case should be used for function names. Update this driver and its
callers accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Typedefs should not be used in U-Boot and structs should be lower case.
Update the code to use struct ns16550 consistently.
Put a header guard on the file while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
After the conversion to device tree the board information becomes
redundant:
Model: Freescale i.MX6 Quad Plus SABRE Smart Device Board
Board: MX6-SabreSD
Remove the printing of the board information.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
Initialize variable 'i2caddress' in adjust_vdd() to zero
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Fix a bug that failed to read/write eeprom on ls1021atsn
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
LX2162 is LX2160 based SoC, it has same die as of LX2160
with different packaging.
LX2162A support 64-bit 2.9GT/s DDR4 memory, i2c, micro-click module,
microSD card, eMMC support, serial console, qspi nor flash, qsgmii,
sgmii, 25g, 40g, 50g network interface, one usb 3.0 and serdes
interface to support three PCIe gen3 interface.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
[Fixed whitespace errors]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When using cygwin64 "dd (coreutils) 8.26 Packaged by Cygwin (8.26-2)",
the last not 512bytes aligned data wat cut off and not burned into SD
card.
Saying the flash.bin size is 1085608 bytes, not 512bytes aligned. It only
burned 1085440 bytes, the leaving 168 bytes were not burnned and cause
boot issue.
So update README dd command to add "conv=notrunc"
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Initialize variable 'i2caddress' in print_vdd() to zero
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
emc2305 is a common driver. It should not use platform specific
i2c address for slave device.
Pass chip_addr as agrument to emc2305_init() and set_fan_speed()
so that emc2305 driver can be used with different platforms.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
According to the reference manual of LS2088A, for a VDD voltage of
0.9V, the entry should be at 01000b.
Fixes: 4911948ec7 ("board/freescale,lsch3: Add entry for 0.9v")
Signed-off-by: Martin Kaistra <martin.kaistra@linutronix.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The board_eth_init() is only used by legacy ethernet driver framework,
so do not compile it when DM_ETH config has been selected.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The board_eth_init() is only used by legacy ethernet driver framework,
so do not compile it when DM_ETH config has been selected.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Move vsc7835 firmware uploading to board_early_init_r(), so that
the switch also can work in DM eTSEC driver.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Most likely these deprecated (removed) variables are not needed. Lets
remove the assignments completely from all spl.c files.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Oleksandr Zhadan and Michael Durrant
Reviewed-by: Simon Glass <sjg@chromium.org>
- Drop ifdef CONFIG_SYS_I2C to initialize
baudrate of i2c
- Drop warning of i2c_early_init_f as follows,
warning: implicit declaration of function 'i2c_early_init_f'; did you
mean 'arch_early_init_r'? [-Wimplicit-function-declaration]
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable secure system counter in board_early_init_f for udelay()
to fix a bug that always return 0 by timer_read_counter()
when boot from qspi(No TFA)
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
- Drop ifdef CONFIG_SYS_I2C to initialize
baudrate of i2c
- Drop warning of i2c_early_init_f as follows,
warning: implicit declaration of function 'i2c_early_init_f'; did you
mean 'arch_early_init_r'? [-Wimplicit-function-declaration]
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable secure system counter in board_early_init_f for udelay()
to fix a bug that always return 0 by timer_read_counter()
when boot from qspi(No TFA)
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support for SDHC adapter identification and configuration
during board init.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The eSDHC adapter card identification and multiplexing configuration
through FPGA had been implemented in both common mmc driver and
fsl_esdhc driver. However it is proper to move these code to board
files and do it during board initialization. The FPGA registers are
also board specific.
This patch is to move eSDHC adapter card identification and
multiplexing configuration from mmc driver to specific board files.
And the option CONFIG_FSL_ESDHC_ADAPTER_IDENT is no longer needed.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[Rebased, Removed T1040QDS change as board does not exist]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add xspi boot source to qixis command to let the soc boot from
flex-nor flash chip.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The correct setting for the RGMII ports on LS1012ARDB is to
enable delay on both Rx and Tx so the interface mode used should
be PHY_INTERFACE_MODE_RGMII_ID
Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Signed-off-by: Anji J <anji.jagarlmudi@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:
It's a **mistake** to use typedef for structures and pointers.
Besides, using typedef for structures is annoying when you try to make
headers self-contained.
Let's say you have the following function declaration in a header:
void foo(bd_t *bd);
This is not self-contained since bd_t is not defined.
To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>
#include <asm/u-boot.h>
void foo(bd_t *bd);
Then, the include direcective pulls in more bloat needlessly.
If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:
struct bd_info;
void foo(struct bd_info *bd);
Right, typedef'ing bd_t is a mistake.
I used coccinelle to generate this commit.
The semantic patch that makes this change is as follows:
<smpl>
@@
typedef bd_t;
@@
-bd_t
+struct bd_info
</smpl>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Quoting Ye Li from NXP:
"We have confirmed with PMIC team, 0x35 is used only on early chips
and not used any more. 0x25 is the final address."
Fix it by merging power_pca9450a_init and power_pca9450b_init into one
function power_pca9450_init.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Current codes assume the OPTEE address is at the end of first DRAM bank.
Adjust the process to allow OPTEE in the middle of first bank.
When OPTEE memory is removed from first bank, it may split the first bank
to two banks, adjust the MMU table for the split case,
Since the default CONFIG_NR_DRAM_BANKS is 4, it is enough, just enlarge
i.MX8MP evk to default to avoid issue.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Silvano di Ninno <silvano.dininno@nxp.com>
Tested-by: Silvano di Ninno <silvano.dininno@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In uMCTL2 Databook, for LPDDR4, it is recommended to set
this register to 1. This can avoid ddr bandwidth is lower
after booting with running for a while.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Jian Li <jian.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
1. set SCHED.rdwr_idle_gap=0
2. set SCHED.pageclose=1
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Jian Li <jian.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
DM, OF_CONTROL, DM_SPI and other driver model migration
deadlines are expired for this board.
Remove it.
Acked-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
There are a few remaining places where we say CONFIG_SECURE_BOOT rather
than CONFIG_IMX HAB. Update these instances.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Eddy Petrișor <eddy.petrisor@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Fixes: d714a75fd4 ("imx: replace CONFIG_SECURE_BOOT with CONFIG_IMX_HAB")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Xiaobo Xie <xiaobo.xie@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Poonam Aggrwal <poonam.aggrwal@nxp.com>
Patch-cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Timur Tabi <timur@tabi.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Po Liu <po.liu@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Naveen Burmi <naveen.burmi@nxp.com>
Patch-cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Poonam Aggrwal <poonam.aggrwal@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Patch-cc: Ashish Kumar <ashish.kumar@nxp.com>
Patch-cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
s/booot/boot/g
The first ase is booot instead of boot and second u-booot instead of
u-boot.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
We no need invoke the code, since spl framework could help
us do that.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Use spl_early_init to replace spl_init, spl_init will be invoked
in board_init_r, we only need use spl_early_init to setup malloc
and scan early dt.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
timer_init has been invoked in arch_cpu_init, no need to invoke
it again in board code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Drop useless getting ccm device, there is no need to explicted do this
in board code, and we not enable SPL CLK currently.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Add the required changes for compiling with DM_ETH on the PPC
DPAA platforms.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When building U-Boot we select the architecture via Kconfig and not ARCH
being passed in via the environment or make cmdline.
Cc: Po Liu <po.liu@nxp.com>
Cc: Qiang Zhao <qiang.zhao@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
- Add DM_ETH support for lx2160aqds, ls2080aqds, ls1088aqds
- QSI related fixes on ls1012a, ls2080a, ls1046a, ls1088a, ls1043a based
platforms
- Bug-fixes/updtaes related to ls1046afrwy, fsl-mc, msi-map property
Add support for selecting the appropriate DTS file depending on the
SERDES protocol used.
The fsl-ls2080a-qds DTS will be used by default if there isn't a DTS
file specifically made for the current SERDES protocol.
This patch adds the necessary DPMAC nodes (DPMAC 1-8) for
protocol 42 (0x2A) on SD#1.
Also, in case CONFIG_DM_ETH and CONFIG_MULTI_DTB_FIT are enabled
implement the board_fit_config_name_match() function in order to choose
the appropriate DTS.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In case CONFIG_DM_ETH is enabled, no hardcoding is necessary for DPAA2
Ethernet devices. Compile out any unnecessary setup when CONFIG_DM_ETH
is activated. Also, force the PCI devices to be enumerated at probe
time.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In case CONFIG_DM_ETH is enabled, no hardcoding is necessary for DPAA2
Ethernet devices. Compile out any unnecessary setup when CONFIG_DM_ETH
is activated. Also, force the PCI devices to be enumerated at probe
time.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support for selecting the appropriate DTS file depending on the
SERDES protocol used. The fsl-ls2088a-qds DTS will be used by default if
there isn't a DTS file specifically made for the current SERDES
protocol.
This patch adds support for the on-board ports (DPMAC 1,2 and 4,5) found
on the SERDES protocols 21(0x15) and 29(0x1d) for SD#1.
On the LS1088AQDS board EMDIO1 is used with two onboard RGMII PHYs
(Realtek RTL8211FD-CG), as well as 2 input/output connectors for
mezzanine cards. Configuration signals from the Qixis FPGA control the
routing of the external MDIOs.
Register 0x54 of the Qixis FPGA controls the routing of the EMDIO1 one
of the 2 IO slots. As a consequence, a new node is added to
describe register 0x54 as a MDIO mux controlled with child nodes
describing all the IO slots as MDIO buses.
Also, in case CONFIG_DM_ETH and CONFIG_MULTI_DTB_FIT are enabled
implement the board_fit_config_name_match() function in order to choose
the appropriate DTS.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
In case CONFIG_DM_ETH and CONFIG_MULTI_DTB_FIT are enabled implement the
board_fit_config_name_match() function in order to choose the
appropriate DTS for the current SERDES protocol configuration.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In case CONFIG_DM_ETH is enabled, no hardcoding is necessary for DPAA2
Ethernet devices. Compile out any unnecessary setup when CONFIG_DM_ETH
is activated. Also, force the PCI devices to be enumerated at probe
time.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
This requires quite a few header-file additions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this uncommon header out of the common header.
Fix up some style problems in flash.h while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Previous patches allow UEFI secure variables to be stored in an RPMB
device using OPTEE. Add a config for the lx2160a hardware so the feature
gets at least compiled.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Remove superfluous differences to lx2160ardb_tfa_defconfig.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add code to check m4 partition booted or not, we will use this
to runtime set device tree file that passed to Linux Kernel.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Make sure that all devices that are powered up by SPL are powered down
before entering into the u-boot. Otherwise the subsystem/device will
never be powered down by SCFW, due to SPL and u-boot are in different
partitions.
Benefiting from power domain driver, this patch implements the function
"imx8_power_off_pd_devices" to power off all active devices.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
- Add DM model for P1010RDB
- Add I2C DM Model support for P1010RDB, T1042RDB, T2080, T4240RDB,
MPC8548CDS, T1024RDB, P4080, P3041DS, P2041RDB, P2020RDB, P1020RDB,
P5040DS
- Fix reference to READM.qe_firmware
Compile the legacy PCIe initialization reoutines for P1010RDB
boards only when DM_PCI is not enabled.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Use the `do_reset` implementation of `arch/arm/lib/reset.c` in SPL
instead. It is very close to what is done here, anyway, and plays
more nicely with the rest of U-Boot than adding a custom `do_reset`
implementation into board files.
`do_reset` from `arch/arm/lib/reset.c` calls `reset_cpu` with 0 as the
addr parameter while the boards are passing WDOG1_BASE_ADDR. This is
ok because the `reset_cpu` implementation uses WDOG1_BASE_ADDR by
default if 0 is passed in.
Co-Authored-by: Harald Seiler <hws@denx.de>
Signed-off-by: Claudius Heine <ch@denx.de>
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Add a module to configure the tamper and secure violation of
the SNVS using the SCU API.
The module also adds some commands:
- snvs_cfg: Configure the SNVS HP and LP registers
- snvs_dgo_cfg: Configure the SNVS DGO bloc if present (8QXP)
- tamper_pin_cfg: Change the configuration of the tamper pins
- snvs_clear_status: Allow to write to LPSR and LPTDSR to clear
status bits
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Franck LENORMAND <franck.lenormand@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Probe the FMan MACs based on the device tree while
retaining the legacy code/functionality.
One notable change introduced here is that, for DM_ETH,
the name of the interfaces is corrected to the fmX-macY
format, that avoids the referral to the MAC block names
which were incorrect for FMan v3 devices (i.e. DTSEC,
TGEC) and had weird formatting (i.e. FM1@DTSEC6, FM1@TGEC1).
The legacy code is left unchanged in this respect.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
mux changes in board file to enable lpuart1 and macro
define for lpuart1 used for mux changes in board configuation
register 13
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In case CONFIG_DM_ETH is enabled, no hardcoding is necessary for
DPAA2 Ethernet devices. Compile out any unnecessary setup when
CONFIG_DM_ETH is activated.
Also, force the PCI devices to be enumerated at probe time.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In case CONFIG_DM_ETH is enabled, no hardcoding is necessary for
DPAA2 Ethernet devices. Compile out any unnecessary setup when
CONFIG_DM_ETH is activated.
Also, force the PCI devices to be enumerated at probe time.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move GIC redistributor tables initialization to CPU setup function.
This patch introduces a GIC redistributor tables init function, and
moves the function of reserving memory for GIC redistributor tables
to soc.c and adds a argument for the memory size to reserve, BTW
rename the function so that it is more readable.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
As the lower 16bit of the redistributor pending table is reserved
for describing the memory attributes, we must give a 64KB aligned
address to the GIC LPI initialization function.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Program the GIC redistributor tables only when succeeded to reserve memory
for them, otherwise kernel will lose the chance to program them using
allocated memory.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The WRLVL_START values are optimized for old DDR MTA18ASF1G72AZ.
Update DDR struct to set new WRLVL_START values so that the new DIMM
MTA18ADF2G72AZ get optimized and the old DIMM still works.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support for backplane kr on t208xqds: remove board specific fixups
on t208xqds for ethernet interfaces specified in device tree as
supported backplane modes.
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support for backplane kr on lx2160aqds: remove board specific fixups
on lx2160aqds for ethernet interfaces specified in device tree as
supported backplane modes.
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support for backplane kr on ls1046aqds: remove board specific fixups
on ls1046aqds for ethernet interfaces specified in device tree as
supported backplane modes.
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch is to define esdhc_status_fixup function for ls1028a to disable
SDHC1/SDHC2 status in device tree node if not selected.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
If the board is configured without CONFIG_GIC_V3_ITS, an error occurs:
board/freescale/lx2160a/lx2160a.c: In function ‘ft_board_setup’:
board/freescale/lx2160a/lx2160a.c:673:6: error: unused variable
‘gic_lpi_base’ [-Werror=unused-variable]
673 | u64 gic_lpi_base;
| ^~~~~~~~~~~~
Let's define the variable as __maybe_unused.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Adjust DRAM size in case BL32 secure payload is loaded (OP-TEE/Trusty),
so during MMU initialization U-Boot won't touch this mem area.
BL32 is loaded to the end of DRAM, bl32 payload size is read from
rom_pointer[1]. This relates to the issue described in
59efa6b52b("imx8m: Fix MMU table issue for OPTEE memory").
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
After triggering a "reboot" command in Linux the following
hang in SPL is observed:
U-Boot SPL 2020.04 (Apr 15 2020 - 10:49:29 -0300)
Normal Boot
WDT: Not found!
Trying to boot from MMC2_2
spl: mmc init failed with error: -70
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
This error happens because the CMD_ERR bit is set in the IRQ status
register after booting from Linux.
To ensure a fresh start, force the VMMC supply to get unpowered first.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
mx6ul_evk uses DM_ETH, so there is no need to have board code
to setup the FEC IOMUX and to register the network ports via the
old board_eth_init() method.
Remove these FEC related pieces of code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Update reference in files detected by
scripts/documentation-file-ref-check
doc/README.<board> => board/<board>/README
Files moved in board directory in
commit 702e6014f1 ("doc: cleanup - move board
READMEs into respective board directories")'
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Update reference in many files detected by
scripts/documentation-file-ref-check
README.imx8image => imx/mkimage/imx8image.txt
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Update reference in many files detected by
scripts/documentation-file-ref-check
README.imximage => imx/mkimage/imximage.txt
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add config to enable the PFE and ETH support.
Also change the pfe secure boot header address.
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1046A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1043A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The SDHC1_DAT4 signal could be routes to SDHC1_VS or SDHC1
adapter slot for SDHC1 usage. When SDHC1 is selected in RCW,
do not force to route it to SDHC1 adapter slot if find it
has already been configued for SDHC1_VS.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Set VID to 800 mV for Rev1 and set VID as per switch settings
for Rev2.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Program GIC LPI configuration table:
1. Redistributor PROCBASER configuration table (which
is common for all redistributors)
2. Redistributor pending table (PENDBASER), for all the
available redistributors.
Signed-off-by: Manish Tomar <manish.tomar@nxp.com>
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Update "board_fix_fdt" with correct counter value "i".
This will fix the issue while fetching the "reg_names"
resource from fdt after fixup.
Signed-off-by: Vikas Singh <vikas.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
As there is only one mx31pdk config file and with upcoming updates to
the Kconfig parsing logic, rather than have an entry in
board/freescale/mx31pdk/Kconfig, move this single setting to the
defconfig file.
Cc: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Magnus Lilja <lilja.magnus@gmail.com>
This fixes the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This fixes the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Instead of resetting the ethernet phy through functions in imx8mq_evk.c, let the
driver reset the phy via dts description adding a reset duration of 10 ms
following atheros 8031's datasheet recommendation.
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Convert imx6sabresd ethernet to driver model to fix the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This should help keeping the screen black when booting the kernel.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Convert imx6sabresd PCI to driver model to fix the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_PCI Please update
the board to use CONFIG_DM_PCI before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
After the conversion the following commands were used for testing:
=> pci enum
PCI: Failed autoconfig bar 10
PCI: Failed autoconfig bar 10
=> pci 1
Scanning PCI devices on bus 1
BusDevFun VendorId DeviceId Device Class Sub-Class
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Currently there are two targets for the i.MX6SX SabreSD board:
mx6sxsabresd_defconfig and mx6sxsabresd_spl_defconfig.
This brings additional maintainance effort without a clear
advantage.
Keep only the mx6sxsabresd_defconfig one and remove
mx6sxsabresd_spl_defconfig to keep it simpler.
Also remove the SPL related code from the board file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Inside Kconfig we must not use the CONFIG_ prefix with the imply statement.
Fixes: 28e3c39e53 ("board: freescale: ls1012a2g5rdb: enable network
support on ls1012a2g5rdb")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1021A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1012A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support of "qixis_reset emmc" command for lx2160a based platforms
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Fix loop in board_fix_fdt that erroneously increments the counter
in all cases whereas the counter should be incremented only if a
matching string has been found.
Fixes: 5d535aa40b ("board: fsl: lx2160a: implement board_fix_fdt")
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Currently LS1028A board code uses arch_misc_init to set up the board mux
on QDS. Move this code to misc_init_r. This is consistent with LS gen 2
and T series SoCs/boards.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The arch_misc_init function is empty on LS108x SoCs/boards, remove it.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The arch_misc_init function is empty on LS2 SoCs/boards, remove it.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Currently LX2 board code uses arch_misc_init to set up the board mux on
RDB and QDS. Move this code to misc_init_r. This is consistent with LS
gen 2 and T series SoCs/boards.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The dts node of the DSPI controller in kernel is spi instead of dspi,
it is not correct if use "/soc/dspi@" to fix up the status of the dts
in kernel, so, modify it to "/soc/spi@".
The DSPI2 and I2C5 are muxed, and the status of DSPI2 node in kernel dts
default value is okay, So set the status of DSPI2 node in kernel dts to
disabled if it is muxed as I2C5.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Passes on the primary address used by u-boot to Linux. The code does a DT
fix-up for ENETC PFs and sets the primary MAC address in IERB. The address
in IERB is restored on ENETC PCI functions at FLR.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
detail_board_ddr_info() is not used anywhere, so simply remove it.
This function is only used by Layerscape, not by i.MX.
This was detected by the following sparse warning:
board/freescale/imx8qxp_mek/imx8qxp_mek.c:115:6: warning: no previous
prototype for ‘detail_board_ddr_info’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
detail_board_ddr_info() is not used anywhere, so simply remove it.
This function is only used by Layerscape, not by i.MX.
This was detected by the following sparse warning:
board/freescale/imx8qm_mek/imx8qm_mek.c:102:6: warning: no previous
prototype for ‘detail_board_ddr_info’ [-Wmissing-prototypes]
Include fdt_support.h header file to fix the following sparse warning:
board/freescale/imx8qm_mek/imx8qm_mek.c:116:5: warning: no previous
prototype for ‘ft_board_setup’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Include fdt_support.h header file to fix the following sparse warning:
board/freescale/imx8qxp_mek/imx8qxp_mek.c:129:5: warning: no previous
prototype for ‘ft_board_setup’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Functions spl_dram_init() and power_init_board() are used only in
the scope of this file, so make them static to fix the following sparse
warnings:
board/freescale/imx8mm_evk/spl.c:40:6: warning: no previous prototype
for ‘spl_dram_init’ [-Wmissing-prototypes]
board/freescale/imx8mm_evk/spl.c:85:5: warning: no previous prototype
for ‘power_init_board’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Add sys_proto.h header file to fix the following sparse warning:
board/freescale/imx8mm_evk/imx8mm_evk.c:59:5: warning: no previous
prototype for ‘board_mmc_get_env_dev’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
The imx8mm doesn't require the hdmi firmware.
Update also the fw version.
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
With commit 0d52bab462 ("mx7dsabre: Enable DM_ETH")
Device Tree has been update and change pfuze3000 node
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
This function related to timer and most of the timer functions are in
time.h, so move this function there.
Signed-off-by: Simon Glass <sjg@chromium.org>
These three clock functions don't use driver model and should be migrated.
In the meantime, create a new file to hold them.
Signed-off-by: Simon Glass <sjg@chromium.org>
These functions relate to setting up the device tree for booting the OS.
The fdt_support.h header file supports similar functions, so move these
there.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is an init function so move it out of the common header. Avoid using
the typedef so that we don't have to include the global_data header file.
Also tidy up the function style in comments while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Currently the following SPL hang is observed:
U-Boot SPL 2020.01-rc5-00079-g797eee36a1 (Jan 06 2020 - 11:24:09 -0300)
Trying to boot from MMC1
Card did not respond to voltage select!
spl: mmc init failed with error: -95
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
Fix it by moving the eSDHC2 initialization to SPL.
While at it, since this board uses DM_MMC all the esdhc board
code can be removed to make the code simpler.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
All platforms currently use the "MCFTMR" DMA timer rather than the PIT
timer, so drop the MCFPIT code.
Cc: Huan Wang <alison.wang@nxp.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Cc: Wolfgang Wegner <w.wegner@astro-kom.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Add board_mmc_get_env_dev, otherwise,
Loading Environment from MMC...
MMC Device 0 not found
*** Warning - No MMC card found, using default environment
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When pmic_get() is used with DM the first parameter must be
the complete node name plus the unit address, so fix it
accordingly.
Reported-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
When pmic_get() is used with DM the first parameter must be
the complete node name plus the unit address, so fix it
accordingly.
Reported-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
When pmic_get() is used with DM the first parameter must be
the complete node name plus the unit address, so fix it
accordingly.
Reported-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The DDR firmware binaries are not part of the U-Boot source code, so
we should look for them in the build directory, where they need to be
copied to before building U-Boot.
The ATF binary is already fetched from the build directory, but the
README files for the i.MX8M EVKs claim that it needs to be copied to
the source directory (which is still true for in-tree builds, but not
in general). Therefore we also fix the READMEs to use the build
directory as the correct location for all additional binary files.
Sined-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Bring in the following merges:
commit 8fbbec12f7
Merge: 87f69f467a63618e71e8
Author: Tom Rini <trini@konsulko.com>
Date: Fri Jan 3 09:48:47 2020 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq into next
- updates and fixes on ls1028a, lx2, ls1046a, MC-DPSPARSER support
commit 87f69f467a
Merge: c0912f9bbf4466b99703
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 24 08:18:19 2019 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx into next
- Enable DM driver on ppc/km boards
- Enable DM_USB for some of NXP powerpc platforms: P5040, T4240, T208x,
T104x, P4080, P2041, P2020, P1020, P3041
- Some updates in mpc85xx-ddr driver, km boards
commit c0912f9bbf
Merge: 533c9f5714a1d6dc3f84
Author: Tom Rini <trini@konsulko.com>
Date: Wed Dec 18 07:20:19 2019 -0500
Merge branch 'next' of https://gitlab.denx.de/u-boot/custodians/u-boot-x86 into next
- Various x86 common codes updated for TPL/SPL
- I2C designware driver updated for PCI
- ICH SPI driver updated to support Apollo Lake
- Add Intel FSP2 base support
- Intel Apollo Lake platform specific drivers support
- Add a new board Google Chromebook Coral
commit 533c9f5714
Merge: 553cb06887033e18b47b
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 17 07:53:08 2019 -0500
Merge tag '20191217-for-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c into next
i2c: for next
- misc: i2c_eeprom:
Add partition support and add ability to query size
of eeprom device and partitions
- i2c common:
add support for offset overflow in to address and add
sandbox tests for it.
commit 553cb06887
Merge: f39abbbc53b4f98b3b16
Author: Tom Rini <trini@konsulko.com>
Date: Thu Dec 12 08:18:59 2019 -0500
Merge tag 'dm-next-13dec19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm into next
buildman improvements including toolchain environment feature
sandbox unicode support in serial
Following the README instructions leads to a non-booting
U-Boot:
U-Boot SPL 2020.01-rc3-00070-g9a0cbae22a (Nov 25 2019 - 13:08:24 -0300)
PMIC: PFUZE100 ID=0x10
DDRINFO: start DRAM init
DDRINFO:ddrphy calibration done
DDRINFO: ddrmix config done
Normal Boot
Trying to boot from MMC2
(It hangs here)
Use the "imx_4.19.35_1.0.0" ATF branch instead, which
fixes such problem and allow the boot to complete again.
Suggested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Currently the following hang is observed when booting a imx6sx-sdb
board:
U-Boot 2020.01-rc5-00004-g643366bcd5 (Dec 19 2019 - 14:56:23 -0300)
CPU: Freescale i.MX6SX rev1.0 996 MHz (running at 792 MHz)
CPU: Extended Commercial temperature grade (-20C to 105C) at 32C
Reset cause: POR
Model: Freescale i.MX6 SoloX SDB RevB Board
Board: MX6SX SABRE SDB revA
DRAM: 1 GiB
initcall sequence bffd8514 failed at call 87804cc0 (err=-19)
### ERROR ### Please RESET the board ###
When pmic_get() is used with DM the first parameter must be
the complete node name plus the unit address.
Fix the pmic_get() parameter to fix the boot regression.
Tested on a imx6sx-sdb and imx6q-sabresd boards.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Enable DP_PWR signal to power the DP to HDMI converter cable.
Signed-off-by: Wen He <wen.he_1@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Current implementation to get board version through GPIO is
broken due to endianness issue hence it is not working for rev B
board.
Fix it to make it work for Rev A as well as Rev B boards
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
At present if CONFIG_SPL_GPIO_SUPPORT is enabled then the GPIO uclass
is included in SPL/TPL without any control for boards. Some boards may
want to disable this to reduce code size where GPIOs are not needed in
SPL or TPL.
Add a new Kconfig option to permit this. Default it to 'y' so that
existing boards work correctly.
Change existing uses of CONFIG_DM_GPIO to CONFIG_IS_ENABLED(DM_GPIO) to
preserve the current behaviour. Also update the 74x164 GPIO driver since
it cannot build with SPL.
This allows us to remove the hacks in config_uncmd_spl.h and
Makefile.uncmd_spl (eventually those files should be removed).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add more clarity by changing the Kconfig entry name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
These functions do not use driver model but are still used. Move them to a
new eeprom.h header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function can be dropped when all boards use driver model for PCI. For
now, move it into init.h with a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
A number of board function belong in init.h with the others. Move them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move these two functions into the irq_funcs.h header file. Also move
interrupt_handler_t as this is used by the irq_install_handler() function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions belong in cpu_func.h since they do not use driver model.
Move them over. Don't bother adding comments since these functions should
be deleted.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present this function sits in its own file but it does not really
justify it. There are similar string functions in vsprintf.h, so move it
there. Also add the missing function comment.
Use the vsprintf.h include file explicitly where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Drop inclusion of crc.h in common.h and use the correct header directly
instead.
With this we can drop the conflicting definition in fw_env.h and rely on
the crc.h header, which is already included.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The board_mmc_init() defined in board files is actually
doing same thing with the cpu_mmc_init() defined in
arch/arm/cpu/armv7/ls102xa/cpu.c. So drop it.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
We can only configure and set the environment in SPL when we have a
particular environment location set that is not "nowhere" like it is in
SECURE_BOOT designs. Update the code to reflect that.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
