Two variants of controllers are supported:
V1 (bitwise only) found in
i.MX21, i.MX27, i.MX31, i.MX51
V2 (byte operations) found in
i.MX25, i.MX35, i.MX50, i.MX53
Only tested on i.MX53 hardware but in both modes
(by modifying the device tree).
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Add Kconfig option WATCHDOG_RESET_DISABLE to disable watchdog reset
in imx_watchdog driver, so that the watchdog will not be fed in
u-boot if CONFIG_WATCHDOG_RESET_DISABLE is enabled.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Support watchdog driver for fsl-lsch2. It's disabled in default.
If you want to use it, please enable CONFIG_IMX_WATCHDOG.
Define CONFIG_WATCHDOG_TIMEOUT_MSECS to set watchdog timeout.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
The Denali NAND controller IP needs three clocks:
- clk: controller core clock
- clk_x: bus interface clock
- ecc_clk: clock at which ECC circuitry is run
Currently, only the first one (50MHz) is provided. The rest of the
two clock ports must be connected to the 200MHz clock line. Add this.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Based on Linux commit cf51e4b9c34407bf0c3d9b582b7837e047e1df47
Add the register read-back, commenting why this is necessary.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Based on Linux commit 1dfac31a5a63ac04a9b5fbc3f5105a586560f191
This commit improves the ->setup_data_interface() hook.
The denali_setup_data_interface() needs the frequency of clk_x
and the ratio of clk_x / clk.
The latter is currently hardcoded in the driver, like this:
#define DENALI_CLK_X_MULT 6
The IP datasheet requires that clk_x / clk be 4, 5, or 6. I just
chose 6 because it is the most defensive value, but it is not optimal.
By getting the clock rate of both "clk" and "clk_x", the driver can
compute the timing values more precisely.
To not break the existing platforms, the fallback value, 50 MHz is
provided. It is true for all upstreamed platforms.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Based on Linux commit 6f1fe97bec349a1fd6c5a8c7c5998d759fe721d5
Currently, denali_dt.c requires a single anonymous clock, but
the Denali User's Guide requires three clocks for this IP:
- clk: controller core clock
- clk_x: bus interface clock
- ecc_clk: clock at which ECC circuitry is run
This commit supports these named clocks to represent the real hardware.
For the backward compatibility, the driver still accepts a single clock
just as before. The clk_x_rate is taken from the clock driver again if
the named clock "clk_x" is available. This will happen only for future
DT, hence the existing DT files are not affected.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
At present it is possible to enable TrueType support but not include any
fonts. This results in a blank display. Select Nimbus as the default font
to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
commit 4f86a724e8 ("power: regulator: denied disable on always-on
regulator") throws an error when requested to disable an always-on
regulator. It is right that an always-on regulator should not be
attempted to be disabled. But at the same time regulator framework
should not return an error when such request is received. Instead
it should just return success without attempting to disable the
specified regulator. This is because the requesting driver will
not have the idea if the regulator is always-on or not. The
requesting driver will always try to enable/disable regulator as
per the required flow. So it is upto regulator framework to not
break such scenarios.
Fixes: 4f86a724e8 ("power: regulator: denied disable on always-on regulator")
Reported-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
When fixed-link phy is used subnode offset is used as phy address. This
number is bigger then space allocated for bus structure (allocated via
mdio_alloc).
bus->phymap[] array has PHY_MAX_ADDR size (32).
That's why writing bus->phymap[addr] where addr is < 0 or > PHY_MAX_ADDR
is causing write to memory which can caused full U-Boot crash.
The patch is checking if address is in correct range.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This commit prevents from re-configuring pins if those were configured
before relocation.
Some pins - like UART or DDR must be setup before relocation
(as they have 'u-boot,dm-pre-reloc' property set in DTS). Without this
change, those pins are re-configured after relocation (pre_reloc_only = 0,
so we do not "continue").
Such behavior may be a problem for DDR PAD configuration, as they might
be already leveled/tuned with original setup).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Enable 'fpga' command in u-boot. User will be able to use the FPGA
command to program the FPGA on Stratix10 SoC.
Signed-off-by: Ang, Chee Hong <chee.hong.ang@intel.com>
Add driver for the JZ47xx MSC controller.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add driver for the efuse block in the JZ47xx SOC.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The VCore III SoCs such as the Luton but also the Ocelot can remap an SPI
flash directly in memory. However, for writing in the flash the
communication has to be done by software.
Each of the signal used for the SPI are exposed in a single register. In
order to be able to use the soft-spi driver, the management of this pin
is done through this simple gpio driver.
Even if the main purpose of this driver is to be used by soft-spi, it can
still be used as a normal gpio driver but with limitation: for example
the first pin can't be used as output.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This driver supports the pin and gpio controller found in the Ocelot and
Luton SoCs.
The driver was inspired from the pinctrl driver in Linux, but was
simplified and was modified to allow supporting an other SoCs (Luton).
For Ocelot and Luton the controller is the same, only the pins to program
differ.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
[changed to only descend into mscc/ dependent on CONFIG_PINCTRL_MSCC]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
On some platforms, as the Ocelot ones, when wanting to control the CS
through software, it is not possible to do it through the GPIO
controller. Indeed, this signal is managed through a dedicated range of
registers inside the SoC..
By declaring the external_cs_manage function as weak, it is possible to
manage the CS at platform level and then using the appropriate registers.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This patch adds SiFive UART driver. The driver is 100% DM driver
and it determines input clock using clk framework.
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
RISC-V privileged architecture v1.10 defines a real-time counter,
exposed as a memory-mapped machine-mode register - mtime. mtime must
run at constant frequency, and the platform must provide a mechanism
for determining the timebase of mtime. The mtime register has a
64-bit precision on all RV32, RV64, and RV128 systems.
Different platform may have different implementation of the mtime
block hence an API riscv_get_time() is required by this driver for
platform codes to hide such implementation details. For example,
on some platforms mtime is provided by the CLINT module, while on
some other platforms a simple 'rdtime' can be used to get the timer
counter.
With this timer driver the U-Boot timer functionalities like delay
works correctly now.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
This adds a driver for RISC-V CPU. Note the driver will bind
a RISC-V timer driver if "timebase-frequency" property is
present in the device tree.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
+ Update the function syscon_node_to_regmap() to force bound on
syscon uclass and directly use the list of device from DM.
+ Remove the static list syscon_list.
This patch avoid issue (crash) when syscon_node_to_regmap() is called
before and after reallocation (list content is invalid).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
In some cases, UART is configured by early boot stage.
To be sure of the initial state of UART and to avoid
spurious chars on console, reset the serial block before
configuring it.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If OP-TEE core is compiled with support of REE FS and RPMB
at the same time (CFG_RPMB_FS ?= y; CFG_RPMB_FS ?= y), and persistent
storage API is used with TEE_STORAGE_PRIVATE storage id, it will
lead to TA panic.
E/TC:? 0 TA panicked with code 0xffff0009
.....
E/TC:? 0 Call stack:
E/TC:? 0 0x000000004002f2f8 TEE_OpenPersistentObject at
lib/libutee/tee_api_objects.c:422
In this particular case TEE_ERROR_STORAGE_NOT_AVAILABLE is more suitable
than TEE_ERROR_NOT_IMPLEMENTED, as it provides to a TA a possibility
to handle this error code [1].
>From GPD TEE Internal Core specification [2]:
TEE_ERROR_STORAGE_NOT_AVAILABLE - if the persistent object is stored in a
storage area which is currently inaccessible. It may be associated with
the device but unplugged, busy, or inaccessible for some other reason.
[1]: 94db01ef44/lib/libutee/tee_api_objects.c (L419)
[2]: https://globalplatform.org/wp-content/uploads/2018/06/GPD_TEE_Internal_Core_API_Specification_v1.1.2.50_PublicReview.pdf
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
When the device is in peripheral mode there is no
struct usb_bus_priv allocated pointer, as the uclass driver
("usb_dev_generic") doesn't call per_device_auto_alloc_size.
This results in writing to the internal SDRAM at
priv->desc_before_addr = true;
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
For USB3.0, the max packetsize for GET_DESCRIPTOR should be
sent as exponent value for 2. This means for 512, max packet
size should be filled with 9(2^9=512). Also, fill the USB
version field with 3.0 if speed is negotiated to Superspeed.
This fixes the issue of DFU gadget download failure with
superspeed. Without this patch, the max packet size is
overflowed to zero as the bMaxPacketsize is of u8 and hence
host is not able to detect this device.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable DM for USB peripheral in the musb-new driver.
Also make sure that the driver can be used in the SPL.
This implies that:
* the driver must work with and without the OF_CONTROL option. That
in turn, implies that the platform data can be passed in a struct
ti_musb_platdata or be read from the dtb
* usb.o is linked in the SPL if host support is enabled
Another change is that the driver does not fail to bind (and stop the boot
process) if one of the child driver does not bind. Reporting the error is
enough. This kind of error would appear if the port is configured in the
DTS but the driver is not activated in the config.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The set_phy_power() callback is part of struct omap_musb_board_data. This
structure is part of the platform data passed to the musb-new driver. This
does not really fit with the Driver Model, so allow not to use struct
omap_musb_board_data to turn the phy on or off.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some drivers might need to access common USB functions such as
usb_get_maximum_speed() or usb_get_dr_mode().
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The keystone platforms can use the generic DC3 driver. Removing the
keystone-spcecific xchi driver and add the configuration options to enable
the generic DWC3 driver on all K2 platforms.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
There don't appear to be any boards enabling CONFIG_USB_DA8XX,
and there is a newer version of the MUSB driver, so let's remove
the legacy version of it.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This patch removes CONFIG_USB_DAVINCI. It's a legacy option
that isn't defined anywhere, and there is a newer MUSB driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
When CONFIG_SPL_DM_USB was added, it was added defaulted on without
protection to ensure it didn't get set for non-DM SPL builds.
This leads to unexpected and confusing failures when building a DM based
U-Boot but with a non-DM SPL, as the defconfig is unlikely to have
CONFIG_SPL_DM_USB actively disabled.
Tweak the Kconfig to not enable this setting unless CONFIG_SPL_DM is set.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
The BITMAP related operations can now be moved to ./include/linux/bitmap.h
file to mimic the Linux kernel directory tree.
This change also allows to remove the lin_gadget_compat.h header file
(which is a legacy code only for composite U-boot layer).
It was also possible to remove #includes from several USB gadget drivers.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
Currently it's not possible to get filesize of downloaded images and
it's impossible to automate some tasks in scripts. So this patch adds
`filesize` environment variable with size (as hex number in bytes) of
the last successfully downloaded file via `sdp` command.
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
At present the 'beep' sound generates a waveform for only one channel even
if two are being used. This means that the beep is twice the frequency it
should be. Correct this by making it a parameter.
The fix in a previous commit was correct for sandbox but not for other
boards.
Fixes: 03f11e87a8 ("sound: Correct data output in sound_create_square_wave()")
Signed-off-by: Simon Glass <sjg@chromium.org>
At present these parameters are hard-coded in the sdl interface code.
Allow them to be specified by the driver instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update snow's device tree and config to use driver model for sound. Also
update the others as best we can.
Spring does not appear to have audio support in the kernel. The smdk5250
and smdk5420 boards use a wolfson codec which I cannot test with. So the
only boards that is tested and known to work are snow, pit and pi.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current ID enums start from 1 but there does not seem to be any reason
that they cannot start with 0. Adjust the code to avoid the +1 in
codec_init().
Signed-off-by: Simon Glass <sjg@chromium.org>
The current dev_read...() functions use s32 and u32 which are convenient
for device tree but not so useful for normal code, which often wants to
use normal integers for values.
Add a helper which supports returning an unsigned int. Also add signed
versions of the unsigned readers.
Signed-off-by: Simon Glass <sjg@chromium.org>
The sound driver pulls together the audio codec and i2s drivers in order
to actually make sounds. It supports setup() and play() methods. The
sound_find_codec_i2s() function allows locating the linked codec and i2s
devices. They can be referred to from uclass-private data.
Add a uclass and a test for sound.
Signed-off-by: Simon Glass <sjg@chromium.org>
The i2s bus is commonly used with audio codecs. It provides a way to
stream digital data sychronously in both directions. U-Boot only supports
audio output, so this uclass is very simple, with a single tx_data()
method.
Add a uclass and a test for i2s.
Signed-off-by: Simon Glass <sjg@chromium.org>
An audio codec provides a way to convert digital data to sound and vice
versa. Add a simple uclass which just supports setting the parameters for
the codec.
Signed-off-by: Simon Glass <sjg@chromium.org>
This structure contains information that is likely needed by any i2s
driver so it seems useful to attach it to the (forthcoming) i2c uclass.
For now, just rename it.
Signed-off-by: Simon Glass <sjg@chromium.org>
The U-Boot sound system provides basic support for beeping. At present it
does not use driver model, but it needs to be converted. Add an option to
enable driver model for sound. For now it is not connected to anything.
Future work will add drivers which use this option. It will then be
removed once everything is converted.
Signed-off-by: Simon Glass <sjg@chromium.org>
For snow the codec is at address 0x11 on the i2c bus, in 7-bit format.
The device tree and code are in 8-bit format (i.e. shifted left one bit).
Fix both. Fix pit in a similar way.
Signed-off-by: Simon Glass <sjg@chromium.org>
These are only used in two functions so can be made local.
Also change the first argument of max98095_do_init() to suit.
Signed-off-by: Simon Glass <sjg@chromium.org>
With driver model we want to do a minimal probe when the device is probed
and then set up the codec interface later when a sound is actully played.
Split this setup code out into its own function to help with this.
Signed-off-by: Simon Glass <sjg@chromium.org>
With driver model we want to do a minimal probe when the device is probed
and then set up the codec interface later when a sound is actully played.
Split this setup code out into its own function to help with this.
Signed-off-by: Simon Glass <sjg@chromium.org>
With driver model we cannot pass in the global struct, but instead want
to pass in the driver-private data. Split some of the code out of
wm8994_init() to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the driver-private data is global. To allow this code to be
used with driver model, change it to pass the data down to each function.
Use the name 'priv' consistently throughout.
Also rename max98095_update_bits() to max98095_bic_or() which is more
descriptive and shorter, thus breaking fewer lines with the parameter
addition.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the driver-private data is global. To allow this code to be
used with driver model, change it to pass the data down to each function.
Use the name 'priv' consistently throughout.
Also rename wm8994_update_bits() to wm8994_bic_or() which is more
descriptive and shorter, thus breaking fewer lines with the parameter
addition.
Signed-off-by: Simon Glass <sjg@chromium.org>
This struct is only used by the Samsung I2C driver and should move into
that driver. For now, rename it so it is clear that is driver-private
info.
Signed-off-by: Simon Glass <sjg@chromium.org>
Building U-Boot with CONFIG_PCI and CONFIG_DM_PCI enabled, but
CONFIG_SPL_PCI_SUPPORT disabled, results in following linker
error:
lib/built-in.o: In function `fdtdec_get_pci_bar32':
lib/fdtdec.c:305: undefined reference to `dm_pci_read_bar32'
fdtdec.c:305:(.text.fdtdec_get_pci_bar32+0x24): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `dm_pci_read_bar32'
This is because reference to dm_pci_read_bar32() remains in lib/fdtdec.c
while SPL build does not descend into drivers/pci directory in
drivers/Makefile if CONFIG_SPL_PCI_SUPPORT is not enabled.
Fix this by applying appropriate #define guards in lib/fdtdec.c.
It looks like ns16550.c has the same problem, so fixed that too.
To simplify this, CONFIG_SPL_PCI_SUPPORT is renamed to CONFIG_SPL_PCI
(enables use of CONFIG_IS_ENABLED() macro).
Suggested-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The function part_init() will only be built when we have both
CONFIG_PARTITIONS and CONFIG_HAVE_BLOCK_DEVICE set. Protect the call to
this function with both of these tests now.
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Vanessa Maegima <vanessa.maegima@nxp.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit f32a8007ef ("dm: i2c: Make i2c_get_chip_for_busnum() fail if the
chip is not detected") introduced a regression for the NVIDIA Jetson TX2.
For some reason the xfer callback of the tegra i2c driver doesn't support
probing the I2C devices with a 0-length message.
Fixing the regression by providing a dummy implementation of probe_chip()
that does nothing.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Add support for lx2160a SoC
-----BEGIN PGP SIGNATURE-----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=aT7d
-----END PGP SIGNATURE-----
Merge tag 'fsl-qoriq-for-v2019.01-rc2' of git://git.denx.de/u-boot-fsl-qoriq
Add TFA boot flow for some Layerscape platforms
Add support for lx2160a SoC
[trini: Add a bunch of missing MAINTAINERS entries]
Signed-off-by: Tom Rini <trini@konsulko.com>
- init DRAM for RK322x in SPL
- add FAN53555 PMIC/regulator driver
- update MicroCrystal RV3029 driver to Kconfig and sync from Linux
- add bootcount uclass and first DM-driver for bootcount
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcDiw9AAoJECaAFcEOcohNEa8H/RBWLbVQjHPXf6EjchXgVcSs
Gc+g2QmKZbN21XebfzBpCuZj62NROTWUcrPtor17yEBiMM1xPfe1vC7qtbkR6USj
VTt1JHeyGx3XafkkUpeps382YPfuaNqtabjwZaXlmeE4/VLbXQPE7x4tC4fdWus4
9K3OGQgRNFirn+RIZ7dQWtCby82PEC3cHkPc/n82cVHofcDsgKYK9mPpfcCn/gWF
A4Fa9cx4pjeaMrBHKjcByCiFmwYBPc97Hqzz64oHOdQP0g3h04ko+2w5DdwdeHVV
jKNcvkHESF4m1RGjrTbLEhy1f5UuOfcA1ise/cDX4pjXlBdwxHmvqT5vsE0MQzI=
=5sHL
-----END PGP SIGNATURE-----
Merge tag 'for-master-20181210' of git://git.denx.de/u-boot-rockchip
Improvements:
- init DRAM for RK322x in SPL
- add FAN53555 PMIC/regulator driver
- update MicroCrystal RV3029 driver to Kconfig and sync from Linux
- add bootcount uclass and first DM-driver for bootcount
This adds a driver for the FAN53555 family of regulators and wraps it
in a PMIC implementation.
While these devices support a 'normal' and 'suspend' mode (controlled
via an external pin) to switch between two programmable voltages, this
incarnation of the driver assumes that the device is always operating
in 'normal' mode.
Only setting/reading the programmed voltage is supported at this time
and the following device functionality remains unsupported:
- switching the selected voltage (via a GPIO)
- disabling the voltage output via software-control
This matches the functionality of the Linux driver.
Tested on a RK3399-Q7 (with 'option 5' devices): setting voltages from
the U-Boot shell and verifying output voltages on the board.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
This implements a driver using a RTC-based backing store for the DM
bootcount implementation. The node configuring this feature will be
compatible with 'u-boot,bootcount-rtc' and the underlying RTC device
shall be reference through the property 'rtc'. An offset into the RTC
device's register space can be provided through the 'offset' property.
Tested on a RK3399-Q7 on a Flamingo carrier board using the SRAM area
of the carrier board's RV3029 RTC.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The original bootcount methods do not provide an interface to DM and
rely on a static configuration for I2C devices (e.g. bus, chip-addr,
etc. are configured through defines statically). On a modern system
that exposes multiple devices in a DTS-configurable way, this is less
than optimal and a interface to DM-based devices will be desirable.
This adds a simple driver that is DM-aware and configurable via DTS.
If ambiguous (i.e. multiple bootcount-devices are present) the
/chosen/u-boot,bootcount-device property can be used to select one
bootcount device.
Initially, this provides support for the following DM devices:
* RTC devices
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Patch for rk322x TPL is not merged, and only SPL is available now,
enable the sdram driver in SPL first. We should update back to TPL
after TPL is enabled for rk322x.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
To reset the DM after a new dtb is loaded, we need to call dm_uninit()
and then dm_init(). This fails however because gd->dm_root is not nullified
by dm_uninit().
Fixing it by setting gd->dm_root in dm_uninit().
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
It is currently not possible to include the support to remove devices in
the SPL. This is however needed by platforms that re-select their dtb after
DM is initialized; they need to remove all the previously bound devices
before triggering a scan of the new DT.
Add a Kconfig option to be able to include the support for device removal
in the SPL.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Seeries-changes:3
- update commit message
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Those driver are not DM drivers per se (not using the PMIC/regulator
framework) and are using the legacy I2C API. Make them compatible with
the DM_I2C API.
This impacts the following drivers:
- palmas (used by am57xx/dra7xx evms)
- tps65218 (used by am43xx evms)
- tps65217 and tps65910 (used by am335x evms and am335x boneblack vboot)
- twl4030 (used by omap3_logicpd)
- tps65217 (used by brppt1)
- twl6030
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This allows the driver to be used without OF_CONTROL.
AM335x support DM_SPL but does not use SPL_OF_CONTROL. Enabling DM_I2C in
SPL thus requires that the omap I2C can be passed platdata.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Move away from SoC specific headers to handle different register layout.
Instead use driver data to get appropriate register layouts like in the
kernel. While at it, perform some mostly cosmetic alignment/cleanup in
the functions being updated.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
If OF_CONTROL is not enabled and DM_SEQ_ALIAS is enabled, we must
assign an alias (requested sequence number) to devices that belongs to a
class with the DM_UC_FLAG_SEQ_ALIAS flag. Otherwise
uclass_find_device_by_seq() cannot be used to get/probe a device. In
particular i2c_get_chip_for_busnum() cannot be used.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
i2c_get_chip_for_busnum() really should check the presence of the chip on
the bus. Most of the users of this function assume that this is done.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This merges the CRC16-CCITT headers into u-boot/crc.h to prepare for
rolling CRC16 into the hash infrastructure. Given that CRC8, CRC32
and CRC32-C already have their prototypes in a single header file, it
seems a good idea to also include CRC16-CCITT in the same.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This syncs drivers/ddr/marvell/a38x/ with the mv_ddr-armada-18.09 branch
of https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell.git.
Specifically this syncs with commit 99d772547314 ("Bump mv_ddr to
release armada-18.09.2").
The complete log of changes is best obtained from the mv-ddr-marvell.git
repository but some relevant highlights are:
ddr3: add missing txsdll parameter
ddr3: fix tfaw timimg parameter
ddr3: fix trrd timimg parameter
merge ddr3 topology header file with mv_ddr_topology one
mv_ddr: a38x: fix zero memory size scrubbing issue
The upstream code is incorporated omitting the portions not relevant to
Armada-38x and DDR3. After that a semi-automated step is used to drop
unused features with unifdef
find drivers/ddr/marvell/a38x/ -name '*.[ch]' | \
xargs unifdef -m -UMV_DDR -UMV_DDR_ATF -UCONFIG_DDR4 \
-UCONFIG_APN806 -UCONFIG_MC_STATIC \
-UCONFIG_MC_STATIC_PRINT -UCONFIG_PHY_STATIC \
-UCONFIG_64BIT -UCONFIG_A3700 -UA3900 -UA80X0 \
-UA70X0
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
- bad usage of clrsetbits_le32
- bad pin definition for AXG Family
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dvG1
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20181207' of git://git.denx.de/u-boot-amlogic
Two fixes for the Amlogic Pinctrl driver :
- bad usage of clrsetbits_le32
- bad pin definition for AXG Family
Some boards feature a capacitance on LDO3's output that is too large,
causing inrush currents which as a result, shut down the AXP209. This
has been reported before, without knowing the actual cause.
A fix appeared to be done with
commit 0e6e34ac8d ("sunxi: Olimex A20 boards: Enable LDO3 and LDO4 regulators").
The description there is a bit misleading, the kernel does not hang
during AXP209 initialization, the PMIC shuts down, causing voltages to
drop and thus the whole system freezes.
While the AXP209 does have the ability to ramp up the voltage slowly, to
reduce these inrush currents, the voltage rate control (VRC) however is
not applicable when switching on the LDO3 output. Only when going from
an enabled lower voltage setting, to a higher voltage setting is the VRC
in effect.
To work around this problem, we set LDO3 to the lowest possible setting
of 0.7 V if it was not yet enabled, and then let the VRC (if enabled) do
its thing. It should be noted, that for some undocumented reason, there
is a short delay needed between setting the LDO3 voltage register and
enabling the power. One would expect that this delay ought to be just
after enabling the output power at 0.7 V, but this did not work.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
The AXP209 LDO3 regulator supports voltage rate control, or can set a
slew rate.
This allows for the power to gradually rise up to the desired voltage,
instead of spiking up as fast as possible. Reason to have this can be
to reduce the inrush currents for example.
There are 3 slopes to choose from, the default, 'none' is a voltage rise
of 0.0167 V/uS, a 1.6 mV/uS and a 0.8 mV/uS voltage rise.
In ideal world (where vendors follow the recommended design guidelines)
this setting should not be enabled by default. Unless of course AXP209
crashes instead of reporting overcurrent condition as it normally should
do in this case.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
The AXP209 has a few 'magisc-ish' values that are better served with
clear defines.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Use a define for the chip version mask on the axp209.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add support to handle USB3 PHYs present on AM57xx/DRA7xx SoCs. This is
needed to move AM57xx to DM_USB.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
syscon_regmap_lookup_by_phandle() can be used to get the regmap of a syscon
device from a reference in the DTS. It operates similarly to the linux
version of the namesake function.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The error is:
In file included from include/part.h:10:0,
from include/usb.h:18,
from include/linux/usb/gadget.h:22,
from drivers/usb/dwc3/ep0.c:20:
include/ide.h:62:14: error: unknown type name ‘uchar’
void ide_led(uchar led, uchar status);
Fixing it by including common.h that defines the uchar type.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The select_dr_mode operation is executed when the glue driver is probed.
The role of this optional function is to configure the operating mode
of the controller at the glue level.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This make the driver more generic. At this point this driver can replace
the dwc3-of-simple implementation.
Make the description in the Kconfig more generic too.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
UCLASS_USB_DEV_GENERIC was meant for USB devices connected to host
controllers, not gadget devices.
Adding a new UCLASS for gadget devices alone.
Also move the generic DM code for USB gadgets in a separate file for
clarity.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Those operations can be used for peripheral operation as well as host
operation.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
# Conflicts:
# drivers/usb/dwc3/core.c
# drivers/usb/host/xhci-dwc3.c
When DM_USB_GADGET the platform code for the USB device must be replaced by
calls to a USB device driver.
usb_gadget_initialize() probes the USB device driver.
usb_gadget_release() removes the USB device driver.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Using CONFIG_DM_USB for this purpose prevents using DM_USB for host and not
for device.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Add 2 functions to wrap the calls to board_usb_init() and
board_usb_cleanup().
This is a preparatory work for DM support for UDC drivers (DM_USB_GADGET).
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
This patch adds code missing when CONFIG_DEBUG_UART_OMAP is enabled as
early debugging UART. The code is basically copied from the ns16550
driver.
Signed-off-by: Felix Brack <fb@ltec.ch>
Due to gpio holes management, stm32_pinctrl_get_gpio_dev() must
be updated.
stm32_pinctrl_get_gpio_dev() returns from a given pin selectors
the corresponding bank gpio device and the gpio_offset inside this
gpio bank.
Update also all functions which makes usage of stm32_pinctrl_get_gpio_dev.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In some STM32 SoC packages, GPIO bank has not always 16 gpios.
Several cases can occur, gpio hole can be located at the beginning,
middle or end of the gpio bank or a combination of these 3
configurations.
For that, gpio bindings offer the gpio-ranges DT property which
described the gpio bank mapping.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Move gpio_dev list filling outside probe() to speed-up U-boot
boot sequence execution. This list is populated only when needed.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This adds channels support for dma controllers that have multiple channels
which can transfer data to/from different devices (enet, usb...).
DMA channle API:
dma_get_by_index()
dma_get_by_name()
dma_request()
dma_free()
dma_enable()
dma_disable()
dma_prepare_rcv_buf()
dma_receive()
dma_send()
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[grygorii.strashko@ti.com: drop unused dma_get_by_index_platdata(),
add metadata to send/receive ops, add dma_prepare_rcv_buf(),
minor clean up]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move dma_ops to a separate header file, following other uclass
implementations. While doing so, this patch also improves dma_ops
documentation.
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
The pin number (first and last) in the bank definition is missing the
pin base offset shifting. This is causing a miscalculation when
retrieving the register and pin offsets in the GPIO driver causing the
'gpio' command to drive the wrong pins / GPIOs in the second GPIO chip
(the AO bank is driven correctly because the shifting is already 0).
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Protect configuration registers with a hardware spinlock.
If a hwspinlock is defined in the device-tree node used it
to be sure that none of the others processors on the SoC could
change the configuration at the same time.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Implement hardware spinlock support for STM32MP1.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add hardware spinlock in the list of the clocks.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This is uclass for Hardware Spinlocks.
It implements two mandatory operations: lock and unlock
and one optional relax operation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
In commit e5e06b65ad ("clk: Allow clock defaults to be set also
during re-reloc state") the earlier guard against setting clock
defaults in pre-reloc state was removed. While it is easy to filter
'assigned-clocks' properties for SPL using CONFIG_OF_SPL_REMOVE_PROPS,
no such mechanism exists for the pre-reloc stage of the full U-Boot.
With the default defconfig for the RK3399-Q7 (which filter the
'assigned-clocks' property for the DTS used by SPL anyway), this
caused a pause during startup of the full U-Boot stage that lasted for
almost 10s (due to the CPU not having been clocked up yet).
This reintroduces the guard from commit f4fcba5c5b ("clk: Allow
clock defaults to be set also during re-reloc state") and extends it
to only apply outside of a TPL/SPL build: i.e. clk_set_defaults will
now run in pre-reloc state for SPL, but only after reloc for the full
U-Boot.
References: commit f4fcba5c5b ("clk: implement clk_set_defaults()")
References: commit e5e06b65ad ("clk: Allow clock defaults to be set
also during re-reloc state")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add ahci compatible support for ls2080a soc.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
[YS: add fallthrough comment]
Reviewed-by: York Sun <york.sun@nxp.com>
Add ahci compatible support for ls1088a soc.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Adds TFABOOT support and allows to pick QE firmware
on basis of boot source.
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[YS: remove line continuation in quoted string]
Reviewed-by: York Sun <york.sun@nxp.com>
Adds TFABOOT support and allows to pick FMAN firmware
on basis of boot source.
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[YS: fix checkpatch issues]
Reviewed-by: York Sun <york.sun@nxp.com>
IFC driver changes to implement the chipselect mappings at run time.
Defines init_early_memctl_regs and init_final_memctl_regs with
chipselect dynamic mapping for nor and nand boot.
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[YS: fix checkpatch issues]
Reviewed-by: York Sun <york.sun@nxp.com>
Sometimes enumeration fails (about 1 in 50 times on my custom board).
The underlying reason is probably electrical but Linux does not have
the problem.
Comparing the Linux / u-boot implementations shows that Linux
retries the error case whereas u-boot aborts early.
Removing the early abort in u-boot fixes the problem.
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
tpm improvements to clear up v1/v2 support
buildman toolchain fixes
New serial options to set/get config
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlwIe0gRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreY02wgAjK9U1ADmoNi4xWgtq83EerxOGTq68BRD
CfnUDgI+FQHNv/LxdZ8lZ2lgGG1xXZ8mdeHWghllHoLEnwMQ3LxfDRnpkyC6VBE9
LvZF4F7BhTnGsKImlloQ5oMhKI4sDKjqRkRL3D633x5dq9Z571obAyGwLMo67vv6
U8iv1mRMr6au46pLvH25DF6h5LuM7TBSJVDlzmFmmD++r/YDroTJfo07qdo8sNqS
0hDPjgp3uqf1mX2cbNHk56a3DmO9fL6Gcvdv0LHGQvRyfQ36TY+cEcDU2y2p+tl+
t1LFamfZvalix9AyJegr3qGMOb9B20ar89EItXzH9J+ahnlZmEat+w==
=VAMW
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5dec18' of git://git.denx.de/u-boot-dm
Minor sandbox enhancements / fixes
tpm improvements to clear up v1/v2 support
buildman toolchain fixes
New serial options to set/get config
SPI flash based MTD devs can be registered/unregistered at any time
through the sf probe command or the spi_flash_free() function.
This commit does not try to fix the root cause as it would probably
require rewriting most of the code and have an mtd_info object
instance per spi_flash object (not to mention that the the spi-flash
layer is likely to be replaced by a spi-nor layer ported from Linux).
Instead, we try to be as safe as can be by checking the code returned
by del_mtd_device() and complain loudly when there's nothing we can
do about the deregistration failure. When that happens we also reset
sf_mtd_info.priv to NULL, and check for NULL pointer in the mtd hooks
so that -ENODEV is returned instead of hitting a NULL pointer
dereference exception when the MTD instance is later accessed by a user.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
The DM implementation of spi_flash_free() does not unregister the MTD
device before removing the spi dev object. This leads to a use-after-free
bug when the MTD device is later accessed by a MTD user (observed when
attaching the device to UBI after env_sf_load() has called
spi_flash_free()).
Implement ->remove() and call spi_flash_mtd_unregister() from there.
Fixes: 9fe6d8716e ("mtd, spi: Add MTD layer driver")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
MTD partition creation code is a bit tricky. It tries to figure out
when things have changed (either MTD dev list or mtdparts/mtdids vars)
and when that happens it first deletes all the partitions that had been
previously created and then creates the new ones based on the new
mtdparts/mtdids values.
But before deleting the old partitions, it ensures that none of the
currently registered parts are being used and bails out when that's
not the case. So, we end up in a situation where, if at least one MTD
dev has one of its partitions used by someone (UBI for instance), the
partitions update logic no longer works for other devs.
Rework the code to relax the logic and allow updates of MTD parts on
devices that are not being used (we still refuse to updates parts on
devices who have at least one of their partitions used by someone).
Fixes: 5db66b3aee ("cmd: mtd: add 'mtd' command")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
The mtdparts variable might contain partition definitions for several
MTD devices. Each partition layout is separated by a ';', so let's
make sure we don't pick a wrong name when mtdparts is malformed.
Fixes: 5db66b3aee ("cmd: mtd: add 'mtd' command")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
The local mtd_name[] variable is limited in size. Return an error if
the name passed in mtdparts does not fit in this local var.
Fixes: 5db66b3aee ("cmd: mtd: add 'mtd' command")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
strstr() does not guarantee that the string we're searching for is
placed at the beginning. Use strncmp() instead.
Fixes: 5db66b3aee ("cmd: mtd: add 'mtd' command")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
The environment is not guaranteed to contain a valid mtdids variable
when called from mtd_search_alternate_name(). Call get_mtdids() instead
of env_get("mtdids").
Fixes: ff4afa8a98 ("mtd: uboot: search for an equivalent MTD name with the mtdids")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
spi_flash_mtd_register() can be called several times and each time it
will register the same mtd_info instance like if it was a new one.
The MTD ID allocation gets crazy when that happens, so let's track the
status of the sf_mtd_info object to avoid that.
Fixes: 9fe6d8716e ("mtd, spi: Add MTD layer driver")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
If we don't do that, partitions might still be exposed while the
underlying device is gone.
Fixes: 2a74930da5 ("mtd: mtdpart: implement proper partition handling")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
Updates to the MTD device list should trigger a new parsing of the
mtdids/mtdparts vars even if those vars haven't changed.
Fixes: 5db66b3aee ("cmd: mtd: add 'mtd' command")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
We need to parse mtdparts/mtids again everytime a device has been
added/removed from the MTD list, but there's currently no way to know
when such an update has been done.
Add an ->updated field to the idr struct that we set to true every time
a device is added/removed and expose a function returning the value
of this field and resetting it to false.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
New callback will supply necessary information, for example,
to ACPI SPCR table.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cache the value of the reg-io-width property for the future use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
New callback will give a necessary information to fill up ACPI SPCR table,
for example. Maybe used later for other purposes.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Change ADR_SPACE_SYSTEM_IO to SERIAL_ADDRESS_SPACE_IO to fix build error:
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases it would be good to know the settings, such as parity,
of current serial console. One example might be an ACPI SPCR table
to generate using these parameters.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Don't disable regulator which are tagged as "regulator-always-on" in DT.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jack Mitchell <jack@embed.me.uk>
Tested-by: Jack Mitchell <jack@embed.me.uk>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Richard Röjfors <richard@puffinpack.se>
Tested-by: Richard Röjfors <richard@puffinpack.se>
Reviewed-by: Felix Brack <fb@ltec.ch>
Tested-by: Felix Brack <fb@ltec.ch>
This functions allow us to get and remap I/O addresses by name, which is useful when there are multiple reg addresses indexed by reg-names property.
This is needed in bmips dma/eth patch series, but can also be used on many
other drivers.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We should not have exported functions in a driver. The i8042_disable()
function is used to disable the keyboard. Provide a remove() method
instead, which is the standard way of disabling a device.
We could potentially add a method to flush input but that does not seem
necessary.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present there are no users of the 64-byte v2 context. The v1 context is
only 16 bytes long and currently an error is raised if too much data is
returned from the EC.
Update the code to limit the size to 16 bytes.
Signed-off-by: Simon Glass <sjg@chromium.org>
If U-Boot is started from SPL or TPL, then those earlier phases deal with
the reset cause. On real hardware this cause may be lost once it is read.
Emulate that behaviour in sandbox by reporting a warm reset when a
previous phase has run since start-up.
Signed-off-by: Simon Glass <sjg@chromium.org>
We cannot be sure that the interface name takes up the full length of the
space available to it. Use strcpy() instead of memcpy() in this case. This
corrects a valgrind warning.
Signed-off-by: Simon Glass <sjg@chromium.org>
The macros used to set the direction of the GPIO pins are misused,
resulting in a wrong behavior when trying to read the GPIO input level
from U-Boot.
A better macro is also used when setting the output direction.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Drop BMP_ALIGN_CENTER define in lcd.c and video_bmp.c as it is
already defined by splash.h. Include splash.h in bmp code.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
According to SD Specifications Part 1 Physical Layer Simplified Specification
Version 6.00 August 29, 2018, section 4.3.10 (Switch Function Command) and
section 5.6 (SCR register), SD cards version 1.00 and 1.01 do not support the
SD CMD 6.
Currently, U-Boot will issue CMD 6 unconditionally in sd_set_card_speed()
while configuring the bus for selected frequency. This will make SD cards
version 1.00 and 1.01 time out and thus fail detection altogether.
Fix this by not sending CMD 6 on such cards. Tested on Matsushita Electric
Industrial Co., Ltd. Japan RP-SD008B / Victor 8MB SD card, CU-SD008, which
is correctly detected with this patch as:
Device: sd@ee160000
Manufacturer ID: 1
OEM: 5041
Name: S008B
Bus Speed: 25000000
Mode : SD Legacy
Rd Block Len: 512
SD version 1.0
High Capacity: No
Capacity: 6.5 MiB
Bus Width: 4-bit
Erase Group Size: 512 Bytes
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
This reverts commit 6f57c34473 since it
does not seem to work at least on rk3399.
The Rockchip Technical Reference Manual (TRM) for the rk3399 says the baud
rate prescaler register is readable only when USR[0] is zero. Since this
bit is defined as "reserved" in the socfpga cylcone5 TRM, let's rather
drop this than making the ns16550 debug uart more platform specific.
Reported-by: Roosen Henri <Henri.Roosen@ginzinger.com>
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com
This release is fully packed with lots of glorious improvements in UEFI
land again!
- Make PE images more standards compliant
- Improve sandbox support
- Improve correctness
- Fix RISC-V execution on virt model
- Honor board defined top of ram (fixes a few boards)
- Imply DM USB access when distro boot is available
- Code cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6o9t
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-12-03
This release is fully packed with lots of glorious improvements in UEFI
land again!
- Make PE images more standards compliant
- Improve sandbox support
- Improve correctness
- Fix RISC-V execution on virt model
- Honor board defined top of ram (fixes a few boards)
- Imply DM USB access when distro boot is available
- Code cleanups
At present line_length is always calculated in video_post_probe(). But
some hardware may use a different line length, e.g. with a 1366-wide
display.
Allow the driver to set this value if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This patch adds a DM driver for the MPC8xx watchdog.
Basically, the watchdog is enabled by default from the start and
SYPCR register has to be writen once to set the timeout and/or
deactivate the watchdog. Once written, it cannot be written again.
It means that wdt_stop() can be called before wdt_start() to stop the
watchdog, but cannot be called if wdt_start() has been called.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
After this change the m41t62.c can be used with RTC subsystem (i.e. date
command) which uses device model (DM).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This change facilitates the conversion of m41t62 RTC driver to device
model (DM).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch moves the RTC M41T62 config define to Kconfig.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch throws an error if 64-bit support is expected
but DMA hardware is not capable of 64-bit support. It also
prints a debug message if DMA is capable of 64-bit but not
using it.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
This patch adds 64-bit addressing support for zynq gem.
This means it can perform send and receive operations on
64-bit address buffers.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
This patch modifies the meson clock driver to use syscon/regmap like
the Linux kernel does, as it is needed if we want to share the same
DTS files.
DTS files are synchronized from Linux 4.19.
Signed-off-by: Loic Devulder <ldevulder@suse.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Add support for the HS400 mode to SDHI driver. This uses the up-tune
mechanism from already supported HS200 tuning.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Move the tap_pos variable, which is the HS200/HS400/SDR104 calibration
offset, into private data, so it can be passed around. This is done in
preparation for the HS400 mode, which needs to adjust this value.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Filter out HS400 support on SoCs where HS400 is not supported yet.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Reorder the tmio_sd_set_clk_rate() function such that it handles all
of the clock requiests correctly. Specifically, before this patch,
clock request with (mmc->clock == 0 && mmc->clk_disable) could leave
the clock enabled, as the function would exit on if (!mmc->clock)
condition on top and will not handle the mmc->clk_disable at all.
Rather than band-aid fixing just that particular problem, reorder
the entire function to make it easier to understand and verify that
all the cases are covered. The function has three sections now:
First, if mmc->clock != 0, we calculate divider for the SD block.
Second, if mmc->clock != 0 and SD block clock are enabled and
current divider is not equal to the new divider, then
stop the clock and update the divider.
Third, if mmc->clk_disable is set, disable the clock, otherwise
enable the clock. This happens independently of divider
update now.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
The TMIO core has a feature where it can automatically disable clock output
when the bus is not in use. While this is useful, it also interferes with
switching the bus to 1.8V and other background tasks of the SD/MMC cards,
which require clock to be enabled.
This patch respects the mmc->clk_disable and only disables the clock when
the MMC core requests it. Otherwise the clock are continuously generated
on the bus.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
The TMIO core has a quirk where divider == 1 must not be set in DDR modes.
Handle this by setting divider to 2, as suggested in the documentation.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Switch the driver to using clk_get_rate()/clk_set_rate() instead of
caching the mclk frequency in it's private data. This is required on
the SDHI variant of the controller, where the upstream mclk need to
be adjusted when using UHS modes.
Platforms which do not support clock framework or do not support it
in eg. SPL default to 100 MHz clock.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
---
V2: - Fix build on certain platforms using SPL without clock framework
V3: - Turn clk_get_rate into a callback and fill it as needed on both
renesas and socionext platforms
Add HS400 properties parsing support to mmc_of_parse().
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
The SDHI clock must be configured differently for HS200/HS400/SDR104
modes. Add support for reconfiguring the SDHI clock settings into the
clock driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The USB storage driver does not compile when CONFIG_BLK is set,
but DM_USB is not set, as we're missing the DM device links for
CONFIG_BLK enabled code paths.
So far it looks like nobody fell into this trap, because no board
enabled CONFIG_BLK and CONFIG_USB_STORAGE while not enabling
CONFIG_DM_USB, but we should still reflect that dependency properly
in Kconfig so that implicit enabling of CONFIG_USB_STORAGE works.
Signed-off-by: Alexander Graf <agraf@suse.de>
When an operating system started via bootefi tries to reset or power off
this is done by calling the EFI runtime ResetSystem(). On most ARMv8 system
the actual reset relies on PSCI. Depending on whether the PSCI firmware
resides the hypervisor (EL2) or in the secure monitor (EL3) either an HVC
or an SMC command has to be issued.
The current implementation always uses SMC. This results in crashes on
systems where the PSCI firmware is implemented in the hypervisor, e.g.
qemu-arm64_defconfig.
The logic to decide which call is needed based on the device tree is
already implemented in the PSCI firmware driver. During the EFI runtime
the device driver model is not available. But we can minimize code
duplication by merging the EFI runtime reset and poweroff code with
the PSCI firmware driver.
As the same HVC/SMC problem is also evident for the ARMv8 do_poweroff
and reset_misc routines let's move them into the same code module.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Variable 'days' must be defined as signed int. Otherwise the conversion
fails for some dates, e.g. 2004-08-25. Cf function rtc_time64_to_tm() in
the Linux kernel source.
Fixes: 992c1db455 "drivers: rtc: resolve year 2038 problem in rtc_to_tm"
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Convert TPM fully to DM
Tidy up sandbox I2C emulation
Add a 'make qcheck' target for faster testing
A few other misc things
(dropped the final patch which breaks clang for some reason)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlwBjx8ACgkQfxc6PpAI
rebWEAf+PMc/M3X6cCKm+8P9xTNFv0gv234HVke1eTDG3eyZB6WQnJn5CS0LwyPj
JUfwk4xK0Sqev/sQ6RuzmxmPAgla6UrEFB355tiZRBtFsMgf8bfevOqbxVqMbZl/
bOe4YsFJ3sAgQDuhi2C5xzm2speGtaB8Qy8s1Zlv2sx3zEnLgRqVgeEVHzulZsk3
gAlWKN3ys6EueYnOladjrrvrfOX8SQKYbThI+ACy7suZbtasGRITwP/4fQoXtmOl
39e9WsiW6DBRW1sxNxpixrOS5trgWjOOFiKlY3GNWP+N34+9vYASwuBWwRWqfgXo
cmelT6AcGiPUbHyr4k0CJHKCJlSbaQ==
=p83K
-----END PGP SIGNATURE-----
Merge tag 'pull-30nov18' of git://git.denx.de/u-boot-dm
Fix sound on sandbox
Convert TPM fully to DM
Tidy up sandbox I2C emulation
Add a 'make qcheck' target for faster testing
A few other misc things
(dropped the final patch which breaks clang for some reason)
This patch sets the PLL of CPU cluster B (BPLL) to 600 MHz.
This decreases the boot time of Linux 4.19 by about 8%.
The 600 MHz are inspired by the 600 MHz used for LPLL initialization
(came in with commit 9f636a249c).
Tested on RK3399-Q7 on Haikou base board.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The "Flamingo" carrier-board for the RK3399-Q7 has a RV3029 populated
and the application will use the off-module RV3029 RTC including the
battery backed SRAM.
To support this use case, this commit includes the following changes:
* updates the rv3029 driver to use DM
* implements the read8/write8 operations
This syncs the implementation with the Linux code (based on 4.17),
porting the trickle-charger support from there (with improvements to
avoid unnecessary EEPROM updates) and adheres to the Linux DTS
binding.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
The MicroCrystal RV3029 driver didn't have a Kconfig entry and was not used
anywhere. Add it to Kconfig to make it selectable.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Make adjustments to the rv1108 clock driver in order to align it
with the internal Rockchip version.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
There was an incorrect check when looping and finding the first
fast enough frequency in the freq_rang table. The code did
actually return the first that was either exactly correct or
too slow.
Signed-off-by: Richard Röjfors <richard@puffinpack.se>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
There was a copy and paste error where the data
enable setting was written to the version register.
Signed-off-by: Richard Röjfors <richard@puffinpack.se>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Currently the else part of ofnode_get_addr_index function
does not fetch addresses based on the index but rather just
returns the base address. Fix that.
Signed-off-by: Keerthy <j-keerthy@ti.com>
At present these functions are not accessible outside the TPM library, but
in some cases we need to call them. Export them in the header file and add
a define for the SHA1 digest size.
Also adjust tpm_open() to call tpm_close() first so that the TPM is in a
known state before opening (e.g. by a previous phase of U-Boot).
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this value is hard-coded in the function that generates a
square wave. Since sample rates vary between different hardware, it makes
more sense to have this as a parameter.
Update the function and its users.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function currently outputs twice as much data as it should and
overwrites its buffer as a result. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some RTC chips have child drivers, e.g. to provide access to their
non-volatile RAM. Scan for these when binding.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sandbox i2c works using emulation drivers which are currently children of
the i2c device:
rtc_0: rtc@43 {
reg = <0x43>;
compatible = "sandbox-rtc";
emul {
compatible = "sandbox,i2c-rtc";
};
};
In this case the emulation device is attached to i2c bus on address 0x43
and provides the Real-Time-Clock (RTC) functionality.
However this is not ideal, since every device on an I2C bus has a child
device. This is only really the case for sandbox, but we want to avoid
special-case code for sandbox.
A better approach seems to be to add a separate node on the bus, an
'emulation parent'. This can be given a bogus address (such as 0xff) and
hides all the emulators away. Then we can use a phandle to point from the
device to the correct emualtor, and only on sandbox. The code to find an
emulator does not interfere with normal i2c operation.
Add a new UCLASS_I2C_EMUL_PARENT uclass which allows finding an emulator
given a bus, and finding a bus given an emulator. This will be used in a
follow-on patch.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add two functions which can find a child device by uclass or by name.
The first is useful with Multi-Function-Devices (MFDs) to find one of a
particular type. The second is useful when only the name is known.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function may be useful to code outside of the code driver-model
implementation. Export it and add a test.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is a newline missing from quite a few printf() strings in these pmic
files. Fix them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Linux uses "cdns,qspi-nor" as compatible string for the cadence
qspi driver, so change driver, docs and all device trees.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
As a preparation for merging the socfpga gen5 devicetree files
from Linux, this patch makes the dwapb gpio driver work correctly
without the 'bank-name' property on the gpio-controller nodes.
This property is not present in the Linux drivers and thus is not
present in the Linux devicetrees. It is only used to access pins
via bank name.
This fallback is necessary since without it, the driver will
return an error code which will lead to an error in U-Boot
startup.
The bank names will still be added to the default board device
trees in follow-up patch, but other boards using this driver and
not including the bank name should also work with the socfpga.dtsi
without adding the bank-name property.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This patch adds a DDR3 driver for MT7629 SoC.
Signed-off-by: Wu Zou <wu.zou@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Many SoCs from MediaTek have a high-speed uart. This UART is compatible
with the ns16550 in legacy mode. It has extra registers for high-speed
mode which can reach a maximum baudrate at 921600.
However this UART will no longer be compatible if it's in high-speed mode.
Some BootROM of MediaTek's SoCs will change the UART into high-speed mode
and the U-Boot must use this driver to initialize the UART.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Tested-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a power domain driver for the Mediatek SCPSYS unit.
The System Control Processor System (SCPSYS) has several power
management related tasks in the system. The tasks include thermal
measurement, dynamic voltage frequency scaling (DVFS), interrupt
filter and lowlevel sleep control. The System Power Manager (SPM)
inside the SCPSYS is for the MTCMOS power domain control.
For now this driver only adds power domain support.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds pinctrl support for MT7623 SoC. And most of the
structures are used to hold the hardware configuration for each
pin.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds pinctrl support for MT7629 SoC. The IO core found on
the SoC has the registers for pinctrl, pinconf and gpio mixed up in
the same register range. Hence the driver also implements the gpio
functionality through UCLASS_GPIO.
This also creates a common file as there might be other chips that use
the same binding and driver, then being a little more abstract could
help in the long run.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds a common driver for the Mediatek SoC integrated
watchdog.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds clock source and clock event for the timer found
on the Mediatek SoCs.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds a driver for MT7623 clock blocks.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds clock modules for MediaTek SoCs:
- Shared part: a common driver which contains the general operations
for plls, muxes, dividers and gates so that we can reuse it in future.
- Specific SoC part: the group of structures used to hold the hardware
configuration for each SoC.
We take MT7629 as an example to demonstrate how to implement driver if
any other MediaTek chips would like to use it.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Drop non-dm code and migrate into DM_SPI.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[jagan: Move config menu in DM_SPI area]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Rename platform_data include file as spi_pl022.h from pl022_spi.h,
this is generic notation used for spi platdata include files.
Acked-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This patch can drop unnecessary include files in
pl022_spi driver.
Acked-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
pl022 spi driver support both OF_CONTROL and PLATDATA, this
patch is trying to simplify the code that differentiating
platdata vs of_control.
- Move OF_CONTROL code at one place
- Handle clock setup code directly in pl022_spi_ofdata_to_platdata
Acked-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This allows to disable the USB driver model in SPL because it checks
the CONFIG_SPL_DM_USB variable for SPL builds. Nothing changes for
regular non-SPL builds.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
Common USB code is built whenever USB is enabled (in non-SPL builds).
The USB uclass is built whenever (SPL_)DM_USB is enabled. Both need to
be independent from CMD_USB.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
This allows building the SPL without driver model for USB. Since
CONFIG_SPL_DM_USB is enabled if and only if CONFIG_DM_USB was enabled
before, this patch does not change the build behaviour.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
This patch adds a minimal clock driver for the Amlogic AXG SoC to handle
the basic gates and PLLs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
We are about to add support for the Amlogic AXG SoC. While very close to
the Gx SoC family, we will need to handle a few thing which are different
in this SoC. Rework the meson arch directory to prepare for this.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This debug print was not designed to be active in non-debug mode.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This adds support for the Amlogic AXG SoC pinctrl and GPIO controller
using a specific set of pinctrl functions which differs from the GX SoCs.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Meson pinctrl needs generic pinctrl, rather than depending on it
select it
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
In preparation of supporting the new Amlogix AGX SoCs, we need to move
the Amlogic GX pinmux functions out of the common code to be able to
add a different set of SoC specific pinmux functions for AXG.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
At present these subsystems are only supported in U-Boot proper but it is
sometimes necessary to support them in SPL, or even TPL. Update the
Kconfig and Makefile to support this. Also adjust GPIO so that it can be
used in TPL if required.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for disabling subpage write support via
CONFIG_SYS_NAND_NO_SUBPAGE_WRITE.
Currently the Linux Arasan driver does not support subpage writes and in
case of running UBI and accessing the same UBI volume from both U-Boot
and Linux it is required to have the same subpage write configuration
else the location of the UBI headers (EC + VID) will be misaligned
(subpage vs page) and incompatible. Hence the need for disabling
subpage write support in the U-Boot Arasan NAND driver.
Signed-off-by: Martin Lund <malu@gomspace.com>
Acked-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds MT7629 qspi driver for accessing SPI NOR flash.
Signed-off-by: Guochun Mao <guochun.mao@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Amlogic Meson SoCs embeds a Flash oriented SPI Controller name SPIFC.
This driver, ported from the Linux meson-spi-spifc driver, add support
for this controller on the Amlogic Meson GX SoCs in U-Boot.
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Some boards have the EMAC TX/RX lanes wired with a different length with
the clock lane, which can be workarounded by setting a TX/RX delay in
the EMAC.
This kind of delays are already defined in the newest device tree
binding of dwmac-sun8i, which has already entered linux-next.
Add support for setting these delays.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Using new mode improves stability of eMMC and SD cards. Without
it SPL fails to load u-boot from SD on Pinebook.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Reviewed-by: Jagan Teki <jagan@openedev.com>
Comment in Linux driver says that clock needs to be doubled only
if we use DDR modes, moreover divider has to be set accordingly.
U-boot driver doesn't declare support for any DDR modes and doesn't
set internal clock divider in CLKCR, so it doubles clock
unconditionally when new mode is used.
Some cards can't handle that and as result SPL fails to load u-boot.
Fixes: de9b1771c3 ("mmc: sunxi: Support new mode")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Allwinner A64 has new mode but doesn't have a mode switch in CCM,
and CCM_MMC_CTRL_MODE_SEL_NEW is not defined, so compilation fails
if MMC_SUNXI_HAS_NEW_MODE is enabled
Introduce new MMC_SUNXI_HAS_MODE_SWITCH option to be able to ifdef usage
of CCM_MMC_CTRL_MODE_SEL_NEW
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
[jagan: update commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
The initial layout for such NAND chips was the following:
+----------------------------------------------------------------------------+
| 1024 (data) | 30 (ECC) | 1024 (data) | 30 (ECC) | 32 (free OOB) | 30 (ECC) |
+----------------------------------------------------------------------------+
This layout has a weakness: reading empty pages trigger ECC errors
(this is expected), but the hardware ECC engine tries to correct the
data anyway and creates itself bitflips, hence bitflips are detected
in erased pages while actually there are none in the NAND chip.
Two solutions have been found at the same time. One was to enlarge the
free OOB area to 64 bytes, changing the layout to be:
+----------------------------------------------------------------------------+
| 1024 (data) | 30 (ECC) | 1024 (data) | 30 (ECC) | 64 (free OOB) | 30 (ECC) |
+----------------------------------------------------------------------------+
^^
The very big drawbacks of this solution are:
1/ It prevents booting from NAND.
2/ The current Linux driver (marvell_nand) does not have such problem
because it already re-reads possible empty pages in raw mode before
checking for bitflips. Using different layouts in U-Boot and Linux
would simply not work.
As this driver does support raw reads now and uses it to check for
empty pages, let's forget about this broken hack and return to the
initial layout with only 32 free OOB bytes.
Fixes: ac56a3b30c ("mtd: nand: pxa3xx: add support for 2KB 8-bit flash")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
This only applies on BCH path.
When an empty page is read, it triggers an uncorrectable error. While
this is expected, the ECC engine might produce itself bitflips in the
read data under certain layouts. To overcome this situation, always
re-read the entire page in raw mode and check for the whole page to be
empty.
Also report the right number of bitflips if there are any.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Raw read support is added by editing a few code sections:
->handle_data_pio() includes the ECC bytes that are not consumed
anymore by the ECC engine.
->prepare_set_command() is changed so that the ECC bytes are
requested as part of the data I/O length.
->drain_fifo() shall also avoid checking the R/B pin too often
when in raw mode.
->read_page_raw()/->read_oob_raw() are written from scratch.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
It is useful to obtain the block-protect setting of the SPI flash, so we
know whether it is fully open or (perhaps partially) write-protected. Add
a method for this. Update the sandbox driver to process this operation and
add a test.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present these functions return 0 on success. For some devices we want
to know how many bytes were transferred. It seems useful to adjust the API
to be more like the POSIX read() and write() functions.
Update these two methods, a test and all users.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
It is useful to be able to invert the colours in some cases so that the
text matches the background colour. Add a parameter to the function to
support this.
It is strange that function takes a private data structure from another
driver as an argument. It seems better to pass the device and have the
function internally work out how to find its required information.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is not normally useful, so change the code to avoid writing out every
data package. This can be enabled with #define DEBUG.
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds new commands to the EC related to setting and clearing events
as well as controlling power-related settings.
Signed-off-by: Simon Glass <sjg@chromium.org>
The LPC driver expects its buffer to be word-aligned. Add the required
flag to the uclass driver to ensure this.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is no advantage to using a u8 for function parameters. It forces
the compiler to mask values and can increase code size. Also the command
enum has been extended to 16 bits. Update the functions to use uint
instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
When the device tree is missing a correct spi slave description below
the bus (compatible "spi-flash" or spi-max-frequency are missing),
the 'set_speed' callback can be called with 'speed' == 0 Hz.
At least with cadence qspi, this leads to a division by zero.
Prevent this by initializing speed to 100 kHz in this case (same
fallback value as is done in 'dm_spi_claim_bus') and issue a warning
to console.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With drivers that have prefix names that are quite long (like
'versatile_') it is useful to have a wider column for the driver's
name when dumping the device driver tree.
Also update the tests to take into account the wider output format.
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As the PCIe specification recommend reading the Vendor ID register
to determine if a Function is present, read the Vendor ID of a
non-existent Function must not result in system error, so we'd better
make the first CFG read to Vendor ID instead of Header Type register
in the PCIe enumeration.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
clk81 divider is 0 based (meaning that 0 value in the register means
divide by 1). Fix clk81 rate calculation for this.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add two functions to ADC uclass's:
- adc_raw_to_uV() to ease ADC raw value conversion to microvolts
- adc_channel_mask() to get channels on consumer side
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds GPIO support for the Mediatek MT7621 SoC, tested on
MT7688 (Gardena smart-gateway). The driver is loosly based on the
Linux kernel version.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
[fixed checkpatch.pl warnings: Prefer 'unsigned int' to bare use of 'unsigned']
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds watchdog support for the Mediatek MT7621 SoC. The driver
is loosly based on the Linux kernel version.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
[fixed merge conflict in drivers/watchdog/Kconfig]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The terminal escape sequence ESC [ <x> ; <y> H is used to set the cursor
position. According to the ECMA 48 standard the upper left corner in the
escape sequences is [1, 1]. The video uclass uses [0, 0] as upper left
corner.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix compiler warning
drivers/misc/fs_loader.c:193:9: warning: format ‘%d’ expects
argument of type ‘int’, but argument 5 has type ‘size_t
{aka long unsigned int}’ [-Wformat=]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Instead of two staged ofnode_to_offset followed by
device_get_global_by_of_offset approach, direcly use the
device_get_global_by_ofnode to fetch the device.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add possibility to update the serial parity used.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
K3 based AM654 devices has DDR memory subsystem that comprises
Synopys DDR controller, Synopsis DDR phy and wrapper logic to
intergrate these blocks into the device. This DDR subsystem
provides an interface to external SDRAM devices. Adding support
for the initialization of the external SDRAM devices by
configuring the DDRSS registers and using the buitin PHY
routines.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: James Doublesin <doublesin@ti.com>
Change static array to const when it is useful to save memory
(move stm32f7_setup=0x18 from .data to .rodata section)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add get_pin_mux ops support to display the pin muxing
description of the sandbox_pins[]
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds gpio get_function ops support.
This function reports the state of a gpio.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add get_pin_muxing() ops to obtain the pin muxing description
a given pin index.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add get_pin_name ops to obtain a pin name given a
pin index of a specified pin-controller.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add get_pins_count ops to obtain the number of pins
owns by a pin-controller.
On STM32 SoCs bindings, each pin-controller owns
several gpio banks. Each GPIO bank can own up to 16 pins.
To obtain the total pins count, walk through each sub-nodes
(ie GPIO banks) and sum each GPIO banks pins number. For that
in probe() we build a list with each GPIO device reference found.
This list will also be used with future get_pin_muxing and get_pin_name
ops to speed up and optimize walk through all GPIO banks.
As this code is common to all STM32 SoCs, this code is put
under SPL_BUILD compilation flag to avoid to increase SPL code size
for STM32F7 which is limited to 32Ko.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Similarly to uclass_first_device_err(), add uclass_next_device_err()
which returns an error if there are no next devices in that uclass.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add pinctrl_get_pin_name() and pinctrl_get_pins_count() methods
to obtain pin's name and pin's muxing given a pin reference.
This will be used by the new pinmux command.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add get_pin_muxing() which allows to display the muxing
of a given pin belonging to a pin-controller.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Testing and analysis shows that at the moment LPC32xx NAND SLC driver
can not get PL080 DMA backbone support in SPL build, because SPL NAND
loaders operate with subpage (ECC step to be precisely) reads, and
this is not supported in the NAND SLC + DMA + hardware ECC calculation
bundle.
The change removes a cautious build time warning and explicitly
disables DMA flavour of the driver for SPL builds, to reduce the
amound of #ifdef sections the code blocks are minimally reorganized.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Build option CONFIG_SYS_MAX_NAND_CHIPS is used by NXP LPC32xx NAND MLC
driver only, as a preparation for potential removal or replacement of
the option the change predefines CONFIG_SYS_MAX_NAND_CHIPS to 1, same
value is used by the single user Work Microwave Work 92105 board, thus
it will be safe now to remove the option as a board specific one.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
The pca953x_gpio driver uses default value of polarity inversion
register. For some devices like PCA9557 and MAX7310, their polarity
inversion register default value is 0xf0. So for high 4 ports, when
reading their values, the values are inverted as the actual level.
This patch clears the polarity inversion register to 0 at init, so
that the port read and write values are aligned.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The earlier commit f4fcba5c5b ("clk: implement clk_set_defaults()")
which introduced the functionality for setting clock defaults such as
rates and parents will skip the processing when executing in a re-reloc
state. This for example can prevent the assigning of clock parents
when running in SPL code. Go ahead and remove this limitation.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Convert the Watchdog driver for AT91SAM9x processors to support
the driver model and device tree. Changes "CONFIG_AT91SAM9_WATCHDOG"
to new "CONFIG_WDT_AT91" Kconfig option.
Signed-off-by: Prasanthi Chellakumar <prasanthi.chellakumar@microchip.com>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If _debug_uart_putc() is called before _debug_uart_init(), the
ns16550 debug uart driver hangs in a tight loop waiting for the
tx FIFO to get empty.
As this can happen via a printf sneaking in before the port calls
debug_uart_init(), let's rather ignore characters before the debug
uart is initialized.
This is done by reading the baudrate divisor and aborting if is zero.
Tested on socfpga_cyclone5_socrates.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Use the uclass_foreach_dev() macro instead of the open coded version.
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver provides support for Sandbox implementation of virtio
transport driver which is used for testing purpose only.
Two drivers are provided. The 2nd one is a driver that lacks the
'notify' op.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For v1.0 compliant device, it always assumes the member 'num_buffers'
exists in the struct virtio_net_hdr while the legacy driver only
presented 'num_buffers' when VIRTIO_NET_F_MRG_RXBUF was negotiated.
Without that feature the structure was 2 bytes shorter.
Update the driver to support the non-legacy device.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
By default QEMU creates legacy PCI transport devices, but we can
ask QEMU to create non-legacy one if we pass additional device
property/value pairs in the command line:
-device virtio-blk-pci,disable-legacy=true,disable-modern=false
This adds a new driver driver to support non-legacy (modern) device
mode. Previous driver/file name is changed accordingly.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add test cases to cover the two newly added PCI APIs:
dm_pci_find_next_capability() & dm_pci_find_next_ext_capability().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This introduces two new APIs dm_pci_find_next_capability() and
dm_pci_find_next_ext_capability() to get PCI capability address
and PCI express extended capability address for a given PCI device
starting from a given offset.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a transport driver that implements UCLASS_VIRTIO for
virtio over pci, which is commonly used on x86.
It only supports the legacy interface of the pci transport, which
is the default device that QEMU emulates.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds virtio block device driver support.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a new block interface type for VirtIO block devices.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
blk_next_free_devnum() can be helpful in some cases. Make it
a public API.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
part_init() is currently called in every DM BLK driver, either
in its bind() or probe() method. However we can use the BLK
uclass driver's post_probe() method to do it automatically.
Update all DM BLK drivers to adopt this change.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently the sandbox block driver uses priv_auto_alloc_size for
the driver data, however that's only available after the device
probe phase. In order to make it accessible in an earlier phase,
switch to use platdata_auto_alloc_size instead.
This patch is the prerequisite for the follow up patch of DM BLK
driver changes to work with Sandbox.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds virtio net device driver support.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
VirtIO can use various different buses and virtio devices are
commonly implemented as PCI devices. But virtual environments
without PCI support (a common situation in embedded devices
models) might use simple memory mapped device (“virtio-mmio”)
instead of the PCI device.
This adds a transport driver that implements UCLASS_VIRTIO for
virtio over mmio.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds support for managing virtual queue/ring, the channel
for high performance I/O between host and guest.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a new virtio uclass driver for “virtio” [1] family of
devices that are are found in virtual environments like QEMU,
yet by design they look like physical devices to the guest.
The uclass driver provides child_pre_probe() and child_post_probe()
methods to do some common operations for virtio device drivers like
device and driver supported feature negotiation, etc.
[1] http://docs.oasis-open.org/virtio/virtio/v1.0/virtio-v1.0.pdf
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some buses need to set up their child devices after they are probed.
Support a common child_post_probe() method for the uclass.
With this change, the two APIs uclass_pre_probe_device() and
uclass_post_probe_device() become symmetric.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for switching the endianness of regmap accesses via the
"little-endian", "big-endian", and "native-endian" boolean properties in
the device tree.
The default endianness is native endianness.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
It is useful to be able to treat the different ranges of a regmap
separately to be able to use distinct offset for them, but this is
currently not implemented in the regmap API.
To preserve backwards compatibility, add regmap_read_range and
regmap_write_range functions that take an additional parameter
'range_num' that identifies the range to operate on.
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The regmap functions currently assume that all register map accesses
have a data width of 32 bits, but there are maps that have different
widths.
To rectify this, implement the regmap_raw_read and regmap_raw_write
functions from the Linux kernel API that specify the width of a desired
read or write operation on a regmap.
Implement the regmap_read and regmap_write functions using these raw
functions in a backwards-compatible manner.
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add some debug output in cases where the initialization of a regmap
fails.
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Both fdtdec_get_addr_size_fixed and of_address_to_resource can fail with
an error, which is not currently checked during regmap initialization.
Since the indentation depth is already quite deep, extract a new
'init_range' method to do the initialization.
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
A newly created property is currently not freed if a name could not be
allocated. This patch fixes the resulting memory leak in the error
patch.
Reported-by: Coverity (CID: 184085)
Fixes: e369e58df7 ("core: Add functions to set properties in live-tree")
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Add a driver for gdsys IHS (Integrated Hardware Systems) FPGAs, which
supports initialization of the FPGA, as well as information gathering.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
This patch adds a driver for the bus associated with a IHS FPGA.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Makefile entries should be sorted.
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
ofnode_read_simple_addr_cells may fail and return a negative error code.
Check for this when initializing regmaps.
Also check if both_len is zero, since this is perfectly possible, and
would lead to a division-by-zero further down the line.
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Document the regmap_alloc() function.
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Commit f2006808f0: ("dm: core: parse chosen node") added a logic
to parse the chosen node during dm_scan_fdt_node(), but unfortunately
it missed adding the same logic in dm_scan_fdt_live(). This mirrors
the logic in the livetree version.
The weird thing is that commit f2006808f0 did update the test case
to test such logic, but even if I reset to that commit, the test case
still fails, and I have no idea how it could pass.
With this fix, the following 2 test cases now pass:
Test: dm_test_bus_children: bus.c
test/dm/bus.c:112, dm_test_bus_children(): num_devices ==
list_count_items(&uc->dev_head): Expected 7, got 6
Test: dm_test_fdt: test-fdt.c
test/dm/test-fdt.c:184, dm_test_fdt(): num_devices ==
list_count_items(&uc->dev_head): Expected 7, got 6
Fixes: f2006808f0 ("dm: core: parse chosen node")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
