Commit graph

1095 commits

Author SHA1 Message Date
Philipp Tomsich
7e0e5c552f rockchip: spi: only wait for completion, if transmitting
The logic in the main transmit loop took a bit of reading the TRM to
fully understand (due to silent assumptions based in internal logic):
the "wait until idle" at the end of each iteration through the loop is
required for the transmit-path as each clearing of the ENA register
(to update run-length in the CTRLR1 register) will implicitly flush
the FIFOs... transmisson can therefore not overlap loop iterations.

This change adds a comment to clarify the reason/need for waiting
until the controller becomes idle and wraps the entire check into an
'if (out)' to make it clear that this is required for transfers with a
transmit-component only (for transfers having a receive-component,
completion of the transmit-side is trivially ensured by having
received the correct number of bytes).

The change does not increase execution time measurably in any of my
tests.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-05-01 00:00:04 +02:00
Philipp Tomsich
b6101e906f rockchip: spi: consistently use false/true with rkspi_enable_chip
While rkspi_enable_chip is called with true/false everywhere else in
the file, one call site uses '0' to denot 'false'.
This change this one parameter to 'false' and effects consistency.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-05-01 00:00:04 +02:00
Philipp Tomsich
e647decdd9 rockchip: spi: fix off-by-one in chunk size computation
The maximum transfer length (in a single transaction) for the Rockchip
SPI controller is 64Kframes (i.e. 0x10000 frames) of 8bit or 16bit
frames and is encoded as (num_frames - 1) in CTRLR1.  The existing
code subtracted the "minus 1" twice for a maximum transfer length of
0xffff (64K - 1) frames.

While this is not strictly an error (the existing code is correct, but
leads to a bit of head-scrating), fix this off-by-one situation.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-05-01 00:00:04 +02:00
Philipp Tomsich
0e661b6df0 rockchip: spi: remove unused code and fields in priv
Even though the priv-structure and the claim-bus function contain
logic for 16bit frames and for unidirectional transfer modes, neither
of these is used anywhere in the driver.

This removes the unused (as in "has no effect") logic and fields.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-05-01 00:00:04 +02:00
Philipp Tomsich
f92cf0adca rockchip: spi: add debug message for delay in CS toggle
In analysing delays introduced for large SPI reads, the absence of any
indication when a delay was inserted (to ensure the CS toggling is
observed by devices) became apparent.

Add an additional debug-only debug message to record the insertion and
duration of any delay (note that the debug-message will cause a delay
on-top of the delay-duration).

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-05-01 00:00:04 +02:00
Tom Rini
b4fde1633e Merge branch 'master' of git://git.denx.de/u-boot-socfpga
- Various stratix10, gen5 updates
2019-04-21 18:59:30 -04:00
Simon Goldschmidt
ac7e14ae0d spi: cadence_qspi: add reset handling
This adds reset handling to the cadence qspi driver.

For backwards compatibility, only a warning is printed when failing to
get reset handles.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-04-17 22:20:17 +02:00
Tom Rini
36c97c4db7 Merge branch 'master' of git://git.denx.de/u-boot-spi
- drop non-DM code from ti_qspi
- support spi-mem for ti_qspi
2019-04-17 09:21:32 -04:00
Vignesh Raghavendra
4c96c61216 spi: ti_qspi: Convert to spi-mem ops
Convert driver to use  spi-mem ops in order to support accelerated MMIO
flash interface in generic way and for better performance.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-17 17:43:54 +05:30
Vignesh Raghavendra
61ae9782ef spi: ti_qspi: Drop non DM code
Now that all boards using TI QSPI have moved to DM and DT, drop non DM
code completely.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[jagan: update MIGRATION.txt, rebase config_whitelist.txt]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-17 17:43:19 +05:30
Siva Durga Prasad Paladugu
1a474381b6 spi: zynqmp_gqspi: Fix tap delay values at 100MHz and 150MHz
This patch fixes the tap delay values to be set at 100MHz and 150MHz
as per TRM by fixing the if condition to use <= instead of <.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-04-16 11:51:34 +02:00
Tom Rini
216800acf1 Merge branch 'master' of git://git.denx.de/u-boot-spi
Conflicts:
	arch/arm/dts/armada-385-amc.dts
	arch/arm/dts/armada-xp-theadorable.dts
	arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-14 00:03:06 -04:00
Christophe Kerello
321d153238 spi: stm32_qspi: move to exec_op
We are facing issues in the driver since SPI NOR framework has moved
on SPI MEM framework, and SPI NAND framework is not running properly
with the current driver.

To be able to solve issues met on SPI NOR Flashes and to be able to
support SPI NAND Flashes, the driver has been reworked. We are now using
exec_op ops instead of using xfer ops.

Thanks to this rework, the driver has been successfully tested with:
 - mx66l51235l SPI NOR Flash on stm32f746 SOC
 - n25q128a SPI NOR Flash on stm32f769 SOC
 - mx66l51235l SPI NOR Flash on stm32mp1 SOC
 - mt29f2g01abagd SPI NAND Flash on stm32mp1 SOC

Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Tested-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
2019-04-12 16:09:13 +02:00
Patrick Delaunay
b0cc1b846f dm: spi: Read default speed and mode values from DT
This patch update the behavior introduced by
commit 96907c0fe5 ("dm: spi: Read default speed and mode values from DT")

In case of DT boot, don't read default speed and mode for SPI from
CONFIG_* but instead read from DT node. This will make sure that boards
with multiple SPI/QSPI controllers can be probed at different
bus frequencies and SPI modes.

Remove also use in boards of the value speed=0 (no more supported)
for ENV in SPI by using CONFIG_ENV_SPI_MAX_HZ=0.

DT values will be always used when available (full DM support of
SPI slave with available DT node) even if speed and mode are requested;
for example in splash screen support (in splash_sf_read_raw)
or in SPL boot (in spl_spi_load_image).
The caller of spi_get_bus_and_cs() no more need to force speed=0.

But the current behavior don't change if the SPI slave is not
present (device with generic driver is created automatically)
or if platdata is used (CONFIG_OF_PLATDATA).

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-12 11:54:50 +05:30
Jared Bents
40264c0ca8 spi: fsl_dspi fix to stop extra transmissions
Update to prevent a byte of zeros being transmitted between
each byte in the tx buffer when providing both a tx buffer
and a rx buffer.

Signed-off-by: Jared Bents <jared.bents@rockwellcollins.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-12 11:24:24 +05:30
Bernhard Messerklinger
567a3eb795 spi: spi-mem: Check if exec_op function is set before calling it
Add check if exec_op is set before calling it.
At the moment it is called unconditionally, which leads to a crash if it
is not set correctly.

Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-12 11:17:39 +05:30
Ley Foon Tan
7eece32812 spi: cadence_qspi: Add quad write support
Use quad write if SPI_TX_QUAD flag is set.

Tested quad write on Stratix 10 SoC board (Micron
serial NOR flash, mt25qu02g)

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2019-04-12 10:54:03 +05:30
Jagan Teki
a51cd54eff spi: Rename sun4i_spi.c into spi-sunxi.c
Now the same SPI controller driver is reusable in all Allwinner
SoC variants, so rename the existing sun4i_spi.c into spi-sunxi.c
which eventually look like a common sunxi driver.

Also update the function, variable, structure names in driver from
sun4i into sunxi.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-03-04 18:08:56 +05:30
Jagan Teki
903e7cf37c spi: sun4i: Driver cleanup
- drop unused macros.
- use base instead of base_addr, for better code readability
- move .probe and .ofdata_to_platdata functions in required
  places to add platdata support in future.
- use sentinel sun4i_spi_ids.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-03-04 18:08:56 +05:30
Jagan Teki
853f4511e9 spi: sun4: Add A31 spi controller support
The usual SPI transmission protocol in Allwinner A10 and A31
controllers share similar context with minimal changes in register
offsets along with few additional register bits on A31.

So, add A31 spi controller support in existing sun4i_spi with A31
specific register offsets and bits.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-03-04 18:08:56 +05:30
Jagan Teki
8d71a19edd spi: sun4i: Add CLK support
Add CLK support to enable AHB and MOD SPI clocks on sun4i_spi driver.

Clock disablement could be done while releasing the bus transfer, but
the existing code doesn't disable the clocks it only taken care of clock
enablement globally in probe.

So to make a proper clock handling, the clocks should enable it in claim
and disable it in release.

This patch would also do that change, by enable and disable clock in
proper order.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
2019-03-04 18:08:56 +05:30
Jagan Teki
178fbd243d spi: sun4i: Support fifo_depth via drvdata
Support fifo_depth via drvdata instead of macro definition, this would
eventually reduce another macro definition for new SPI controller fifo
depth support addition.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
2019-03-04 18:08:56 +05:30
Jagan Teki
8d9bf46847 spi: sun4i: Access registers and bits via enum offsets
Allwinner support two different SPI controllers one for A10 and
another for A31 with minimal changes in register offsets and
respective register bits, but the logic for accessing the SPI
master via SPI slave remains nearly similar.

Add enum offsets for register set and register bits, so-that
it can access both classes of SPI controllers.

Assign same control register for global, transfer and fifo control
registers to make the same code compatible with A31 SPI controller.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Stefan Mavrodiev <stefan@olimex.com> # A20-SOM204
2019-03-04 18:08:56 +05:30
Jagan Teki
8cbf09ba1c spi: sun4i: Simplify reg writes using set/clrbits_le32
Update the existing register writes using setbits_le32 and
clrbits_le32 in required places.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-03-04 18:08:56 +05:30
Jagan Teki
6cb6aa602b spi: sun4i: Poll for rxfifo to be filled up
To drain rx fifo the fifo need to poll for how much data has
been filled up in rx fifo.

To achieve this, the current code is using wait_for_bit logic
on control register with exchange burst mode mask, which is not
a proper way of waiting for fifo filled up.

So, add code for polling rxfifo to be filled up using fifo
status register.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
2019-03-04 18:08:56 +05:30
Horatiu.Vultur@microchip.com
1b77de4476 spi: designware: Change include order
With current order of include files, the file designware_spi.c
can't see that the struct global_data has the member
board_type when CONFIG_BOARD_TYPES is defined. By not seeing this
then all the members are shifted in the struct global_data.
So when the driver is trying to read from device tree blob, it
would pass the wrong address to the function 'fdtdev_get_int'.
This will make to use the default frequency 500000.

The fix consists of changing the order of include files in
designware_spi.c to include first common.h file.

Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2019-03-04 17:56:26 +05:30
David Rivshin
b8b88e6aff spi: omap3: fix set_wordlen() reading from incorrect address for CHCONF
_omap3_spi_set_wordlen() indexed the regs->channel[] array with the
old wordlen (instead of the chipselect number) when reading the current
CHCONF register value. This meant it read from the wrong memory location,
modified that value, and then wrote it back to the correct CHCONF
register. The end result is that most slave configuration settings would
be lost, such as clock divisor, clock/chipselect polarities, etc.

Fixes: 77b8d04854 ("spi: omap3: Convert to driver model")
Signed-off-by: David Rivshin <drivshin@allworx.com>
2019-02-28 14:21:46 -05:00
Michal Simek
f3976cc61f spi: zynqmp_gqspi: Enable versal compatible string
Trivial patch.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-02-14 14:31:09 +01:00
Vignesh R
6d82517836 configs: Don't use SPI_FLASH_BAR as default
Now that new SPI NOR layer uses stateless 4 byte opcodes by default,
don't enable SPI_FLASH_BAR. For SPI controllers that cannot support
4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c,
renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to
not break functionality.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07 15:33:22 +05:30
Vignesh R
c4e8862308 mtd: spi: Switch to new SPI NOR framework
Switch spi_flash_* interfaces to call into new SPI NOR framework via MTD
layer. Fix up sf_dataflash to work in legacy way. And update sandbox to
use new interfaces/definitions

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07 15:33:21 +05:30
Vignesh R
6430eea639 spi: Add non DM version of SPI_MEM
Add non DM version of SPI_MEM to support easy migration to new SPI NOR
framework. This can be removed once DM_SPI conversion is complete.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07 15:33:21 +05:30
Vignesh R
76094485e4 spi: spi-mem: Claim SPI bus before spi mem access
It is necessary to call spi_claim_bus() before starting any SPI
transactions and this restriction would also apply when calling spi-mem
operations. Therefore claim and release bus before requesting transfer
via exec_op.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07 15:33:21 +05:30
Vignesh R
12563f768e spi: spi-mem: Extend spi_mem_adjust_op_size() to honor max xfer size
Extend spi_mem_adjust_op_size() to take spi->max_write_size and
spi->max_read_size into account.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07 15:33:21 +05:30
Vignesh R
6d373e523f spi: spi-mem: Allow use of spi_mem_exec_op for all SPI modes
SPI controllers support all types of SPI modes including dual/quad bus
widths. Therefore remove constraint wrt SPI mode from spi-mem layer.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07 15:33:21 +05:30
Ye Li
65a106e36f spi: mxc_spi: Fix build warning on ARM64 platforms
When building mxc_spi driver on ARM64 platforms, get below build warnings.
Fix it in this patch.

In file included from include/common.h:48:0,
 from drivers/spi/mxc_spi.c:9:
 drivers/spi/mxc_spi.c: In function ‘spi_xchg_single’:
drivers/spi/mxc_spi.c:232:21: warning: cast from pointer to integer of
different size [-Wpointer-to-int-cast]
 _func_, bitlen, (u32)dout, (u32)din);
 ^
 include/log.h:135:26: note: in definition of macro ‘debug_cond’
printf(pr_fmt(fmt), ##args); \
 ^~~~
 drivers/spi/mxc_spi.c:231:2: note: in expansion of macro ‘debug’
debug("%s: bitlen %d dout 0x%x din 0x%x\n",
 ^~~~~
 drivers/spi/mxc_spi.c:232:32: warning: cast from pointer to integer of
different size [-Wpointer-to-int-cast]
 _func_, bitlen, (u32)dout, (u32)din);
 ^
 include/log.h:135:26: note: in definition of macro ‘debug_cond’
printf(pr_fmt(fmt), ##args); \
 ^~~~
 drivers/spi/mxc_spi.c:231:2: note: in expansion of macro ‘debug’
debug("%s: bitlen %d dout 0x%x din 0x%x\n",
 ^~~~~

Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-01-28 20:35:47 +01:00
Lars Povlsen
fd6e0b0525 mips: spi: mscc: Add fast bitbang SPI driver
This patch add a new SPI driver for MSCC SOCs that does not sport the
designware SPI hardware controller.

Performance gain: 7.664 seconds vs. 17.633 for 1 Mbyte write.

Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-01-16 13:56:43 +01:00
Stefan Mavrodiev
5c1a87de58 spi: sun4i: Add rx_buf NULL pointer check
Current driver doesn't check if the destination pointer is NULL.
This cause the data from the FIFO to be stored inside the internal
SDRAM ( address 0 ).

The patch add simple check if the destination pointer is NULL.

Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Jagan Teki <jagan@openedev.com>
[jagan: fix commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-01-02 00:54:05 +05:30
Gregory CLEMENT
bea91b0c9b DW SPI: Allow to overload the management of the external CS
On some platforms, as the Ocelot ones, when wanting to control the CS
through software, it is not possible to do it through the GPIO
controller. Indeed, this signal is managed through a dedicated range of
registers inside the SoC..

By declaring the external_cs_manage function as weak, it is possible to
manage the CS at platform level and then using the appropriate registers.

Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
2018-12-19 15:23:01 +01:00
Tom Rini
9450ab2ba8 Merge branch 'master' of git://git.denx.de/u-boot-spi
- Various MTD fixes from Boris
- Zap various unused / legacy paths.
- pxa3xx NAND update from Miquel

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-12-05 15:06:24 -05:00
Christophe Leroy
fb0204e48b spi, mpc8xx: migrate to DM_SPI
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
2018-12-03 10:44:10 -05:00
Simon Goldschmidt
2a3a99932b spi: cadence_qspi: use "cdns,qspi-nor" as compatible
Linux uses "cdns,qspi-nor" as compatible string for the cadence
qspi driver, so change driver, docs and all device trees.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2018-11-29 12:45:15 +01:00
Christophe Leroy
f34d0315e9 spi: mpc8xx: Migrate to DM_SPI
Drop non-dm code and migrate into DM_SPI.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[jagan: Move config menu in DM_SPI area]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-11-27 21:06:53 +05:30
Jagan Teki
e2cae51472 spi: Remove unused spi_init
Remove spi_init definition which never used on
respective code since from many years.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-11-27 21:06:53 +05:30
Jagan Teki
3ae6030cf9 dm: platform_data: spi: s/pl022_spi.h/spi_pl022.h
Rename platform_data include file as spi_pl022.h from pl022_spi.h,
this is generic notation used for spi platdata include files.

Acked-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-11-27 21:06:46 +05:30
Jagan Teki
e6f76d555e spi: pl022: Drop unnecessary include files
This patch can drop unnecessary include files in
pl022_spi driver.

Acked-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-11-27 21:06:37 +05:30
Jagan Teki
3deb1f731d spi: pl022: Simplify platdata code
pl022 spi driver support both OF_CONTROL and PLATDATA, this
patch is trying to simplify the code that differentiating
platdata vs of_control.
- Move OF_CONTROL code at one place
- Handle clock setup code directly in pl022_spi_ofdata_to_platdata

Acked-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-11-27 21:06:19 +05:30
Guochun Mao
052cafd2a5 spi: mtk_qspi: add qspi driver for MT7629 SoC
This patch adds MT7629 qspi driver for accessing SPI NOR flash.

Signed-off-by: Guochun Mao <guochun.mao@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-11-24 14:41:12 +05:30
Neil Armstrong
9d26506a9c spi: Add Amlogic Meson SPI Flash Controller driver
The Amlogic Meson SoCs embeds a Flash oriented SPI Controller name SPIFC.
This driver, ported from the Linux meson-spi-spifc driver, add support
for this controller on the Amlogic Meson GX SoCs in U-Boot.

Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2018-11-24 14:41:12 +05:30
Simon Goldschmidt
12bfb2e05f dm: spi: prevent setting a speed of 0 Hz
When the device tree is missing a correct spi slave description below
the bus (compatible "spi-flash" or spi-max-frequency are missing),
the 'set_speed' callback can be called with 'speed' == 0 Hz.
At least with cadence qspi, this leads to a division by zero.

Prevent this by initializing speed to 100 kHz in this case (same
fallback value as is done in 'dm_spi_claim_bus') and issue a warning
to console.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-11-20 19:14:22 -07:00
Michal Simek
ec48b6c991 arm64: versal: Add support for new Xilinx Versal ACAPs
Xilinx is introducing Versal, an adaptive compute acceleration platform
(ACAP), built on 7nm FinFET process technology. Versal ACAPs combine
Scalar Processing Engines, Adaptable Hardware Engines, and Intelligent
Engines with leading-edge memory and interfacing technologies to deliver
powerful heterogeneous acceleration for any application. The Versal AI
Core series has five devices, offering 128 to 400 AI Engines. The series
includes dual-core Arm Cortex™-A72 application processors, dual-core Arm
Cortex-R5 real-time processors, 256KB of on-chip memory with ECC, more
than 1,900 DSP engines optimized for high-precision floating point with
low latency.

The patch is adding necessary infrastructure in place without enabling
platform which is done in separate patch.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-10-16 16:53:21 +02:00
Tom Rini
e6cd05e502 Merge branch 'master' of git://git.denx.de/u-boot-spi 2018-10-12 11:54:13 -04:00
Jagan Teki
ba3c22bf18 spi: davinci: Add platdata support
Davanci spi driver has DM support already, this patch
add support for platdata so-that SPL can use it for
low foot-print.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Adam Ford <aford173@gmail.com>
2018-10-10 11:35:06 +05:30
Simon Glass
5e24a2ef8b dm: spi: Add logging of some return values
When SPI flash operations fail it is helpful to be able to see the error
codes and where they are generated. Add logging to capture this
information for read operations.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Simon Glass
c3aed5db59 sandbox: spi: Add more logging
Add logging to aid debugging features in these drivers. Also drop some
code in sandbox_spi_xfer() which is not used.

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-10-09 04:40:27 -06:00
Stefan Roese
5eee9dee41 spi: Add SPI driver for MT76xx SoCs
This patch adds the SPI driver for the MediaTek MT7688 SoC (and
derivates). Its been tested on the LinkIt Smart 7688 and the Gardena
Smart Gateway with and SPI NOR on CS0 and on the Gardena Smart
Gateway additionally with an SPI NAND on CS1.

Note that the SPI controller only supports a max transfer size of 32
bytes. This driver implementes a workaround to enable bigger xfer
sizes to speed up the transfer especially for the SPI NAND support.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Piotr Dymacz <pepe2k@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-10-04 18:27:28 +05:30
Tom Rini
592cd5defd Merge branch 'master' of git://git.denx.de/u-boot-spi
This is the PR for SPI-NAND changes along with few spi changes.

[trini: Re-sync changes for ls1012afrwy_qspi*_defconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-10-02 17:01:46 -04:00
Marek Vasut
b3bec25256 spi: sh_qspi: Add DM support to SH QSPI driver
Add DM support to the SH QSPI driver while retaining non-DM support.
The later is required as this driver is used in SPL which has a size
limitation of 16 kiB.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
[jagan: use proper commit head]
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-10-02 22:14:59 +05:30
Ashish Kumar
4ccb2f2115 driver/spi: fsl_qspi: Remove non-DM stuff
Convert fsl_qspi.c to complete DM mode.

Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Tested-by: Rajat Srivastava <rajat.srivastava@nxp.com>
Tested-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-10-02 22:13:58 +05:30
Ley Foon Tan
6ac5909f51 spi: designware_spi: Add reset ctrl to driver
Add code to reset all reset signals as in SPI DT node. A reset property
is an optional feature, so only print out a warning and do not fail if a
reset property is not present.

If a reset property is discovered, then use it to deassert, thus
bringing the IP out of reset.

Release reset when _remove().

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-10-02 22:13:58 +05:30
Quentin Schulz
8a4791fa08 spi: add support for ARM PL022 SPI controller
This adds support for the ARM PL022 SPI controller for the standard
variant (0x00041022) which has a 16bit wide and 8 locations deep TX/RX
FIFO.

A few parts were borrowed from the Linux kernel driver.

Cc: Armando Visconti <armando.visconti@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
2018-09-25 21:49:18 -04:00
Boris Brezillon
d13f5b254a spi: Extend the core to ease integration of SPI memory controllers
Some controllers are exposing high-level interfaces to access various
kind of SPI memories. Unfortunately they do not fit in the current
spi_controller model and usually have drivers placed in
drivers/mtd/spi-nor which are only supporting SPI NORs and not SPI
memories in general.

This is an attempt at defining a SPI memory interface which works for
all kinds of SPI memories (NORs, NANDs, SRAMs).

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
2018-09-20 20:10:49 +05:30
Stefan Mavrodiev
7f25d81797 arm: sunxi: Allwinner A10 SPI driver
Add spi driver for sun4i, sun5i and sun7i SoCs. The driver is
adapted from mailine kernel.

Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-08-03 11:14:08 +05:30
Chris Packham
4f4dde0a62 spi: kirkwood: add orion-spi compatible string
This matches the compatible string used by the Linux kernel. This will
allow u-boot to use the same device tree files.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
[jagan: use armada instead of orion on .data]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-08-03 11:14:02 +05:30
Jagan Teki
f5ff46f6e5 spi: kirkwood: Get drvdata in .ofdata_to_platdata
Get the is_errata_50mhz_ac in .ofdata_to_platdata, and
reuse it in .set_mode this can eventually initialized
dt code at once and adding room to add platdata.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-08-03 11:09:53 +05:30
Christophe Kerello
d68b6ad138 spi: stm32_qspi: rework mode management
This patch solves quad read issue with Macronix/Micron spi nor.

Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-07-23 14:33:21 -04:00
Christophe Kerello
ceff933e1e spi: stm32_qspi: assign functional operation mode in _stm32_qspi_gen_ccr
This patch assigns the functional operation mode in _stm32_qspi_gen_ccr
function.

Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-07-23 14:33:21 -04:00
Siva Durga Prasad Paladugu
22cca1730e spi: zynqmp_gqspi: Add support for ZynqMP qspi driver
This patch adds qspi driver support for ZynqMP SoC. This
driver is responsible for communicating with qspi flash
devices.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
[jagan: removed GQSPI_MIO_NUM_ macros]
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-07-16 14:01:47 +05:30
Vipul Kumar
6e9d9fcb4c spi: xilinx_spi: convert to livetree
Update the xilinx spi driver to support a live tree.

Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-07-16 14:01:20 +05:30
Vipul Kumar
83ce646943 spi: xilinx_spi: Added support to read JEDEC-id twice at the boot time
This patch is for the startup block issue in the spi controller.
SPI clock is passing through STARTUP block to FLASH. STARTUP block
don't provide clock as soon as QSPI provides command. So, first
command fails.

This patch added support to read JEDEC id in xilinx_spi_xfer ().

Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-07-16 14:01:20 +05:30
Vipul Kumar
0c0de58f7b spi: xilinx_spi: Modify transfer logic xilinx_spi_xfer() function
This patch modify xilinx_spi_xfer() function and add rxfifo() and
txfifo() functions to add the modularity so that these functions
can be used by other functions within the same file.

This patch also added support to read fifo_size from dts.

Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-07-16 14:01:20 +05:30
Michal Simek
4e7c1a2651 spi: xilinx: Read reg base address from DTS file
This patch added support to read register base address from DTS file.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-07-16 14:01:20 +05:30
Ley Foon Tan
8b71e46cea spi: cadence_qspi: Fix warning cast from pointer to integer of different size
Use "%p" to print cmdbuf.

Compilation warning as below:

  CC      spl/drivers/spi/cadence_qspi_apb.o
  LD      spl/lib/built-in.o
drivers/spi/cadence_qspi_apb.c: In function ‘cadence_qspi_apb_indirect_write_setup’:
drivers/spi/cadence_qspi_apb.c:696:18: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
          cmdlen, (unsigned int)cmdbuf);

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
2018-07-12 09:22:11 +02:00
Ley Foon Tan
9bd39dd8e5 spi: cadence_qspi: Fix compilation warning
Use "%zu" for size_t data type.

Compilation warning as below:

In file included from include/linux/bug.h:7:0,
                 from include/common.h:26,
                 from drivers/spi/cadence_qspi.c:8:
drivers/spi/cadence_qspi.c: In function ‘cadence_spi_xfer’:
drivers/spi/cadence_qspi.c:211:8: warning: format ‘%d’ expects argument of type ‘int’, but argument 3 has type ‘size_t {aka long unsigned int}’ [-Wformat=]
  debug("%s: len=%d [bytes]\n", __func__, data_bytes);
        ^
include/linux/printk.h:37:21: note: in definition of macro ‘pr_fmt’
 #define pr_fmt(fmt) fmt
                     ^~~
include/log.h:142:2: note: in expansion of macro ‘debug_cond’
  debug_cond(_DEBUG, fmt, ##args)
  ^~~~~~~~~~
drivers/spi/cadence_qspi.c:211:2: note: in expansion of macro ‘debug’
  debug("%s: len=%d [bytes]\n", __func__, data_bytes);

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
2018-07-12 09:22:11 +02:00
Thomas Fitzsimmons
894c3ad27f board: arm: Add support for Broadcom BCM7445
Add support for loading U-Boot on the Broadcom 7445 SoC.  This port
assumes Broadcom's BOLT bootloader is acting as the second stage
bootloader, and U-Boot is acting as the third stage bootloader, loaded
as an ELF program by BOLT.

Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
2018-07-10 16:55:57 -04:00
Hannes Schmelzer
c0eaffa039 spi: omap3: fix claim/release bus within DM
The claim/release bus function must not reset the whole SPI core because
settings regarding wordlen, clock-frequency and so on made by
set_wordlen, set_mode, set_speed get lost with this action. Resulting in
a non-functional SPI.

Without DM the failure didn't came up since after the spi_reset within
claim bus all the setup (wordlen, mode, ...) was called, in DM they are
called by the spi uclass.

We change now the things as following for having a working SPI instance
in DM:

- move the spi_reset(...) to the probe call in DM for having a known
hardware state after probe. Without DM we don't have a probe call, so we
issue the reset as before during the claim_bus call.

- in release bus we just reset the modulctrl to the reset-value (spi-
slave)

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-06-28 19:54:10 +05:30
Hannes Schmelzer
9cddf70ead spi: omap3: fix set_speed and set_mode dm callbacks
commit 8480792287
("spi: omap3: Skip set_mode, set_speed from claim") did break SPI
support on my AM335x board.

The named commit:

- ignored the responsible arguments (speed, mode)
The set speed/mode function must use the supplied function arguments to
work properly. With this commit we take those arguments and transfer
them to the priv-data.

- used wrong udevice pointer for getting priv data
the udevice-pointer within function argument is already the spi-bus
device, so it is wrong looking here for some parent (ocp-bus in this
case) and getting priv-pointer from there.

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-06-25 15:35:15 +05:30
Hannes Schmelzer
b1d2b529b4 spi: omap3: pre-initialize bus-speed with max. slave-speed
Otherwise the frequency is zero and the clock divider cannot be setup by
'omap3_spi_set_speed' function.

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-06-25 15:35:01 +05:30
Michael Trimarchi
34ad749141 spi: mxc_spi: Fix chipselect on DM_SPI driver uclass
CS GPIO activation low/high is determinated by the device tree
so we don't need to take in accoung in cs_activate and cs_deactivate

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-06-25 15:23:06 +05:30
Michael Trimarchi
618e8e20c2 spi: mxc: Fix compilation problem of DM_SPI class driver
drivers/spi/mxc_spi.c:507: undefined reference to `dev_get_addr'
linux-ld.bfd: BFD (GNU Binutils) 2.29.1 assertion fail elf32-arm.c:9509

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-06-25 14:18:41 +05:30
Vipul Kumar
240cd7566e spi: zynq_qspi: Fixed incorrect return value error
This patch replaced "return 0" with "return status" to fix the
incorrect return value error reported by the coverity.

Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
[jagan: rebased on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-06-25 14:13:57 +05:30
Ley Foon Tan
6c353674bd spi: cadence_qspi: Change to use devfdt_get_addr_index()
Change to use devfdt_get_addr_index() function to get fdt address.

Original code has compilation warning below:

drivers/spi/cadence_qspi.c: In function ‘cadence_spi_ofdata_to_platdata’:
drivers/spi/cadence_qspi.c:297:18: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
  plat->regbase = (void *)data[0];
                  ^
drivers/spi/cadence_qspi.c:298:18: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
  plat->ahbbase = (void *)data[2];
                  ^
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-06-04 23:30:04 +05:30
Tom Rini
2a046ff5e9 Merge branch 'master' of git://git.denx.de/u-boot-mips 2018-06-01 16:46:39 -04:00
Álvaro Fernández Rojas
46689a94b2 spi: bcm63xx_hsspi: convert to use live dt
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-06-01 15:56:02 +02:00
Álvaro Fernández Rojas
85e1ddbaf0 spi: bcm63xx_spi: convert to use live dt
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-06-01 15:56:02 +02:00
Tom Rini
8ada17dde8 Merge branch 'master' of git://git.denx.de/u-boot-spi
- Fix a conflict in drivers/spi/atcspi200_spi.c related to the riscv
  tree fixing a warning.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-30 14:51:37 -04:00
Rick Chen
6083cf3883 spi: atcspi200: Fix compiler warning
Fix warning as below when compile in 64-bit.

warning: format '%u' expects argument of type
'unsigned int', but argument 6 has type 'size_t
{aka long unsigned int}

Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
2018-05-29 14:45:03 +08:00
Heinrich Schuchardt
4bcd88a2d8 spi: fsl_qspi: remove superfluous assignment
In

	void *rx_addr = NULL;
	rx_add = A;

the first assignment has no effect. Remove it.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-05-16 19:19:24 +05:30
Heinrich Schuchardt
266580612f spi: lpc32xx: simplify logical expression
A & A & B == A & B

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-05-16 19:19:06 +05:30
Heinrich Schuchardt
8fad5e0b11 spi: atcspi200: avoid NULL dereference
For SPI_XFER_BEGIN | SPI_XFER_END the code sets data_out = NULL.
In the debug statement we should not dereference this value.
As we do not transfer any data the debug statement is not needed in this
case anyway.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-05-16 19:18:41 +05:30
Patrice Chotard
5e46123bf3 spi: stm32_qspi: Add reset support
In some situation, QSPI controller is already configured by an early
boot stage, adding reset support will insure that QSPI controller is
started from a pristine state.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-05-16 18:41:21 +05:30
Patrice Chotard
2a6ca73691 spi: stm32_qspi: Use dev_read_xxx API
Use dev_read_xxx() instead of old manner fdt_xxx() API

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-05-16 18:41:21 +05:30
Christophe Kerello
495f3b2ae5 spi: stm32_qspi: Add chip select management
Quad-SPI interface is able to manage 2 spi nor devices.
FSEL bit selects the flash memory to be addressed in single flash mode.

Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-05-16 18:41:21 +05:30
Christophe Kerello
76afe56a44 spi: stm32_qspi: Add st, stm32f469-qspi compatible string
Add "st,stm32f469-qspi" compatible which is used on kernel side.
This will be necessary when DT will be synchronised from kernel.

Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-05-16 18:41:21 +05:30
Christophe Kerello
09e1772067 spi: stm32_qspi: Align reg-names with kernel 4.12 RC1
Align qspi bindings following kernel dt-bindings
Documentation/devicetree/bindings/mtd/stm32-quadspi.txt
from kernel v4.12-rc1.

Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-05-16 18:41:21 +05:30
Patrice Chotard
8c4592d278 spi: stm32_qspi: Sort include files alphabetically
Sort include files by alphabetical order

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-05-16 18:41:21 +05:30
Patrick Delaunay
936abadac8 spi: stm32_qspi: Solve issue detected by checkpatch
Fix parameters function alingemnt
Fix variable declaration

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-05-16 18:41:21 +05:30
Patrice Chotard
12e7c91a0b spi: stm32_qspi: Remove CONFIG_CLK flag
As all platforms which uses this driver have CONFIG_CLK flag
enable in their defconfig, we can remove it from driver code.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-05-16 18:41:21 +05:30
Marek Behún
dbbd5bdd27 spi: mvebu_a3700_spi: Use Armada 37xx clk driver for SPI clock frequency
Since now we have driver for clocks on Armada 37xx, use it to determine
SQF clock frequency for the SPI driver.

Also change the default config files for Armada 37xx devices so that
the clock driver is enabled by default, otherwise the SPI driver cannot
be enabled.

Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-14 10:00:15 +02:00
Rajat Srivastava
1f55356411 spi: fsl_qspi: Introduce is_controller_busy function
Some SoCs have different endianness of QSPI IP if compared
to endianness of core. The function is_controller_busy()
checks if the QSPI controller is busy or not, considering
the endianness of the QSPI IP.

Signed-off-by: Rajat Srivastava <rajat.srivastava@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-05-09 09:17:51 -05:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Tom Rini
d024236e5a Remove unnecessary instances of DECLARE_GLOBAL_DATA_PTR
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-27 14:54:48 -04:00
Adam Ford
f1b1f77060 Convert CONFIG_SPI to Kconfig
This converts the following to Kconfig:
   CONFIG_SPI

This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver.  For now, just update
the CONFIG tests.  This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.

Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-27 14:54:11 -04:00
Eugeniy Paltsev
9b14ac5cc2 spi: dw: invert wait condition in dw_spi_xfer
While switching to readl_poll_timeout macros from custom code
the waiting condition was accidently inverted, so it was pure
luck that this code works at least in some conditions.

Fix that by inverting exit condition for readl_poll_timeout.

Fixes: c6b4f031d9 ("DW SPI: fix tx data loss on FIFO flush")

Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-04-23 11:16:41 +05:30
Marek Vasut
ea5512eb09 spi: sh_qspi: Make use of the 32byte FIFO
The QSPI controller on RCar Gen2 has 32byte FIFO. Instead of doing
the SPI transmission 1 byte at time, if there is a 32byte chunk of
data to be transferred, fill the FIFO completely and then transfer
the data to/from the FIFO. This increases the SPI NOR access speed
significantly.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2018-04-11 23:19:51 +02:00
Marek Vasut
9573db654d spi: sh_qspi: Replace ad hoc waiting with wait_for_bit
Replace the ad-hoc endless loops with wait_for_bit() with
reasonable timeout. Note that the loops had internal 10uS
delays, although there is no reason for those on this HW,
so they are dropped.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2018-04-11 23:19:51 +02:00
Marek Vasut
1182264952 spi: sh_qspi: Drop SPBDCR wait
Waiting for SPBDCR == 1 is not required and is covered by the
subsequent wait for SPSR_SPRFF, so drop this.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2018-04-11 23:19:51 +02:00
Marek Vasut
0e6fa20b14 spi: sh_qspi: Replace data types with short ones
Just replace unsigned {char,short,long} with u{8,16,32},
no functional change.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2018-04-11 23:19:50 +02:00
Marek Vasut
fbebea27e1 mtd: spi: Add Renesas RPC SPI-flash driver
Add driver for the RPC block in SPI-flash mode. This driver allows
access to a SPI NOR flash attached to the RPC block and does not
support RPC in Hyperflash mode. Note that this block is extremely
selective when communicating with the SPI NOR.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-04-11 23:12:01 +02:00
Tom Rini
e80fa2c2c0 Revert "spi: atmel: Drop non-dm code"
As we aren't quite able to convert some platforms with a very small size
limit in SPL yet, we need to revert this for now.

This reverts commit 7b09477873.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-07 09:19:00 -04:00
Tom Rini
5270df2836 Revert "spi: atmel: Drop atmel_spi.h"
As we aren't quite able to convert some platforms with a very small size
limit in SPL yet, we need to revert this for now.

This reverts commit 37434db29b.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-07 09:18:26 -04:00
Christophe Leroy
18f8d4c60d powercp: mpc8xx: move commproc.h
include/commproc.h is dedicated to the 8xx, rename it cpm_8xx.h and
move it into arch/powerpc/include/asm

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
2018-04-06 16:30:37 -04:00
Christophe Leroy
ee1e600c13 powerpc: mpc8xx: Change CONFIG_8xx to CONFIG_MPC8xx
CONFIG_8xx doesn't mean much outside of arch/powerpc/
This patch renames it CONFIG_MPC8xx just like CONFIG_MPC85xx etc ...
It also renames 8xx_immap.h to immap_8xx.h to be consistent with
other file names.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
2018-04-06 16:30:37 -04:00
Jagan Teki
89d4fc153b spi: atmel: default y if DM_SPI && ARCH_AT91
ATMEL_SPI is now fully converted to driver-model and
respective boards switch to DM_SPI as well,
so make default y for ARCH_AT91

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Wenyou Yang <wenyouya@gmail.com>
2018-04-06 16:11:09 -04:00
Jagan Teki
37434db29b spi: atmel: Drop atmel_spi.h
atmel_spi.h has register offsets, and atmel_spi_slave
structure, move it into .c file for better readability
and drop atmel_spi.h

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Wenyou Yang <wenyouya@gmail.com>
2018-04-06 16:11:09 -04:00
Jagan Teki
7b09477873 spi: atmel: Drop non-dm code
All board configs are now enabled DM_SPI for SPL and
U-Boot proper, so now its time to drop non-dm code.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Wenyou Yang <wenyouya@gmail.com>
2018-04-06 16:11:09 -04:00
Jagan Teki
9bf48e2ee8 spi: atmel: Add ifdef for DM_GPIO code
Few boards are configuring gpio directly from board instead
using drivers/gpio so add ifdef for DM_GPIO to compatible
for both the cases.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Wenyou Yang <wenyouya@gmail.com>
2018-04-06 16:11:09 -04:00
Sjoerd Simons
63018a3edd omap3: spi: Correct ti, pindir-d0-out-d1-in parsing
The ti,pindir-d0-out-d1-in property is not expected to have a value
according to the device-tree binding, so treat it as a boolean not a
uint property.

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-03-23 23:03:29 +05:30
Eugeniy Paltsev
4b5f6c52e7 DW SPI: use 32 bit access instead of 16 and 32 bit mix
Current DW SPI driver uses 32 bit access for some registers and
16 bit access for others. So if DW SPI IP is connected via bus
which doesn't support 16 bit access we will get bus error.

Fix that by switching to 32 bit access only instead of 16 and 32 bit mix

Additional Documentation to Support this Change:
The DW_apb_ssi databook states:
"All registers in the DW_apb_ssi are addressed at 32-bit boundaries
to remain consistent with the AHB bus. Where the physical size of
any register is less than 32-bits wide, the upper unused bits of
the 32-bit boundary are reserved. Writing to these bits has no
effect; reading from these bits returns 0." [1]

[1] Section 6.1 of dw_apb_ssi.pdf (version 3.22a)

Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-03-22 23:01:35 +05:30
Eugeniy Paltsev
bcdcb3e61e DW SPI: add option to use external gpio for chip select
DW SPI internal chip select management has limitation:
it hold CS line in active state only when the FIFO is not
empty. If the FIFO freed before we add new data the SPI transaction will
be broken.

So add option to use external gpio for chip select. Gpio can be added
via device tree using standard gpio bindings.

Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-03-22 23:01:35 +05:30
Eugeniy Paltsev
d3d8aaec74 DW SPI: refactor poll_transfer functions
There is no sense in waiting for RX data in dw_reader function:
there is no chance that RX data will appear in RX FIFO if
RX FIFO is empty after previous TX write in dw_writer function.
So get rid of this waiting. After that we can get rid of dw_reader
return value and make it returning void. After that we can get rid
of dw_reader return value check in poll_transfer function.

With these changes we're getting closer to Linux DW SPI driver.

Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-03-22 23:01:35 +05:30
Eugeniy Paltsev
fc282c7bcb DW SPI: fix transmit only mode
In current implementation we get -ETIMEDOUT error when we try to use
transmit only mode (SPI_TMOD_TO)
This happens because in transmit only mode input FIFO never gets any data
which breaks our logic in dw_reader(): we are waiting until RX data will be
ready in dw_reader, but this newer happens, so we return with error.

Fix that by using SPI_TMOD_TR instead of SPI_TMOD_TO which allows to use
RX FIFO.

Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-03-22 23:01:35 +05:30
Eugeniy Paltsev
c6b4f031d9 DW SPI: fix tx data loss on FIFO flush
In current implementation if some data still exists in Tx FIFO it
can be silently flushed, i.e. dropped on disabling of the controller,
which happens when writing 0 to DW_SPI_SSIENR (it happens in the
beginning of new transfer)

So add wait for current transmit operation to complete to be sure
that current transmit operation is finished before new one.

Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-03-22 23:01:35 +05:30
Tom Rini
3fa9bc7969 Merge git://git.denx.de/u-boot-spi 2018-03-15 08:27:27 -04:00
Jagan Teki
b2b41d2777 spi: omap3: Fix redeclared error
omap3_spi_set_speed|mode redeclared bus symbol, fix the same.

error:
drivers/spi/omap3_spi.c: In function ‘omap3_spi_set_speed’:
drivers/spi/omap3_spi.c:650:18: error: ‘bus’ redeclared as different kind of symbol
  struct udevice *bus = dev->parent;

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-03-14 23:19:31 +05:30
Patrice Chotard
aa5e3e22f4 board: stm32: switch to DM STM32 timer
Use available DM stm32_timer driver instead of dedicated
mach-stm32/stm32fx/timer.c.

Remove all defines or files previously used for timer usage in
arch/arm/include/asm/arch-stm32fx and in arch/arm/mach-stm32/stm32fx

Enable DM STM32_TIMER for STM32F4/F7 and H7.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-03-13 21:45:37 -04:00
Jagan Teki
8480792287 spi: omap3: Skip set_mode, set_speed from claim
set_mode, set_seed functions has separate function pointers
in dm_spi_ops, so use them in relevent one instead of
calling from claim_bus.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-03-13 19:50:10 +05:30
Jagan Teki
15927aef02 spi: atcspi200: Drop non-dm code
Boards adp-ae3xx_defconfig, nx25-ae250_defconfig
already enabled DM_SPI, so non-dm code make no use
of it hence droped.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-03-13 19:50:10 +05:30
Tuomas Tynkkynen
fbca0e66cc spi: Migrate CONFIG_CF_SPI to Kconfig
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-02-13 23:01:44 -05:00
Tuomas Tynkkynen
4a942f49b8 spi: Migrate CONFIG_KIRKWOOD_SPI to Kconfig
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-02-13 23:01:44 -05:00
Tuomas Tynkkynen
2c4b096b4c spi: Migrate CONFIG_LPC32XX_SSP to Kconfig
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-02-13 23:01:44 -05:00
Tuomas Tynkkynen
bbdf38698e spi: Migrate CONFIG_MPC8XXX_SPI to Kconfig
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-02-13 23:01:44 -05:00
Tuomas Tynkkynen
60e5456291 spi: Migrate CONFIG_MXC_SPI to Kconfig
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-02-13 23:01:44 -05:00
Tuomas Tynkkynen
7b819b569e spi: Migrate CONFIG_MXS_SPI to Kconfig
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-02-13 23:00:53 -05:00
Tuomas Tynkkynen
a5dfabea19 spi: Migrate CONFIG_SH_QSPI to Kconfig
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-02-13 23:00:47 -05:00
Tuomas Tynkkynen
95d3877a58 spi: Migrate CONFIG_SH_SPI to Kconfig
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-02-13 23:00:29 -05:00
Heinrich Schuchardt
923837e159 atcspi200: avoid possible NULL dereference
Check if ns before and not after dereferencing it.

Indicated by cppcheck.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2018-02-07 22:06:18 -05:00
Tom Rini
1d12a7c8cd Merge git://git.denx.de/u-boot-spi 2018-01-26 07:46:34 -05:00
Eugeniy Paltsev
58c125b9e2 DW SPI: Get clock value from Device Tree
Add option to set spi controller clock frequency via device tree
using standard clock bindings.

Define dw_spi_get_clk function as 'weak' as some targets
(like SOCFPGA_GEN5 and SOCFPGA_ARRIA10) don't use standard clock API
and implement dw_spi_get_clk their own way in their clock manager.

Get rid of clock_manager.h include as we don't use
cm_get_spi_controller_clk_hz function anymore. (we use redefined
dw_spi_get_clk in SOCFPGA clock managers instead)

Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-01-26 11:26:16 +05:30
Vignesh R
aaa21d3ffc spi: cadence_qspi_apb: Make flash writes 32 bit aligned
Make flash writes 32 bit aligned by using bounce buffers to deal with
non 32 bit aligned buffers.
This is required because as per TI K2G TRM[1], the external master is
only permitted to issue 32-bit data interface writes until the last word
of an indirect transfer. Otherwise indirect writes is known to fail
sometimes.

[1] http://www.ti.com/lit/ug/spruhy8g/spruhy8g.pdf

Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Reviewed-by: Jason Rush <jarush@gmail.com>
Acked-by: Jason Rush <jarush@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-01-24 12:11:36 +05:30
Vignesh R
a743e2ba38 Revert "spi: cadence_qspi_apb: Use 32 bit indirect write transaction when possible"
This reverts commit 57897c13de.

Using bounce_buf.c to handle non-DMA alignment problems is bad as
bounce_buf.c does cache manipulations which is not required. Therefore
revert this patch in favour of local bounce buffer solution in the next
patch.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Reviewed-by: Jason Rush <jarush@gmail.com>
Acked-by: Jason Rush <jarush@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-01-24 12:11:36 +05:30
Goldschmidt Simon
948ad4f075 Revert "spi: cadence_qspi_apb: Use 32 bit indirect read transaction when possible"
This reverts commit b63b46313e.

This commit changed cadence_qspi_apb to use bouncebuf.c, which invalidates
the data cache after reading. This is meant for dma transfers only and
breaks the cadence_qspi driver which copies via cpu only: data that is
copied by the cpu is in cache only and the cache invalidation at the end
throws away this data.

Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jason Rush <jarush@gmail.com>
Acked-by: Jason Rush <jarush@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-01-24 12:11:36 +05:30
Jason Rush
15a70a5da3 spi: cadence_spi: Sync DT bindings with Linux
Adopt the Linux DT bindings. This also fixes an issue
with the indaddrtrig register on the Cadence QSPI
device being programmed with the wrong value for the
socfpga arch.

Tested on TI K2G platform:
Tested-by: Vignesh R <vigneshr@ti.com>

Tested on a socfpga-cyclonev board:
Tested-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>

Signed-off-by: Jason Rush <jarush@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Acked-by: Marek Vasut <marex@denx.de>
2018-01-24 12:07:50 +05:30
Chris Packham
df16881cea spi: kirkwood_spi: implement workaround for FE-9144572
Erratum NO. FE-9144572: The device SPI interface supports frequencies of
up to 50 MHz.  However, due to this erratum, when the device core clock
is 250 MHz and the SPI interfaces is configured for 50MHz SPI clock and
CPOL=CPHA=1 there might occur data corruption on reads from the SPI
device.

Implement the workaround by setting the TMISO_SAMPLE value to 0x2
in the timing1 register.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-01-24 12:04:08 +05:30
Mario Six
24fc1ec2ee spi: spi-uclass: Fix style violations
Remove a superfluous newline, and reduce the scope of a variable.

Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-01-24 12:04:08 +05:30
Mario Six
184fa1c8da spi: Remove spi_setup_slave_fdt
A previous patch removed the spi_flash_probe_fdt function, which
contained the last call of the spi_setup_slave_fdt function, which is
now equally obsolete.

This patch removes the function.

Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-01-24 12:04:07 +05:30
Mario Six
c5b88f29ba spi: Remove obsolete spi_base_setup_slave_fdt
0efc024 ("spi_flash: Add spi_flash_probe_fdt() to locate SPI by FDT
node") added a helper function spi_base_setup_slave_fdt to to set up a
SPI slave from a given FDT blob. The only user was the exynos SPI
driver.

But commit 73186c9 ("dm: exynos: Convert SPI to driver model") removed
the use of this function, hence rendering it obsolete.

Remove this function, as well as the CONFIG_OF_SPI option, which guarded
only this function.

Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-01-24 12:04:07 +05:30
Mario Six
547bcc3d18 spi: Fix style violation and improve code
This patch fixes a printf specifier style violation, reduces the scope
of a variable, and turns a void pointer that is used with pointer
arithmetic into a u8 pointer.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-01-24 12:04:07 +05:30
Álvaro Fernández Rojas
29cc4368ad dm: spi: add BCM63xx HSSPI driver
This driver is a simplified version of linux/drivers/spi/spi-bcm63xx-hsspi.c

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-01-24 12:04:06 +05:30
Álvaro Fernández Rojas
5ac07d2969 dm: spi: add BCM63xx SPI driver
This driver is a simplified version of linux/drivers/spi/spi-bcm63xx.c

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-01-24 12:03:43 +05:30
Álvaro Fernández Rojas
48263504c8 wait_bit: use wait_for_bit_le32 and remove wait_for_bit
wait_for_bit callers use the 32 bit LE version

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-01-24 12:03:43 +05:30
Adam Ford
26410c1517 Convert CONFIG_DAVINCI_SPI to Kconfig
This converts the following to Kconfig:
   CONFIG_DAVINCI_SPI

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-01-22 16:43:30 -05:00
Peng Fan
afe8e1b033 spi: fsl_qspi: support i.MX6UL/6ULLL/7D
The QSPI module on i.MX7D is modified from i.MX6SX. The module used on
i.MX6UL/6ULL is reused from i.MX7D. They share same tx buffer size.

The endianness is not set at qspi driver initialization. So if we don't
boot from QSPI, we will get wrong endianness when accessing from AHB
address directly.

Add the compatible entry for 6ul/7d.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2018-01-12 14:28:04 +01:00
Rick Chen
6720e4ae7a cosmetic: atcspi200: Rename function name as atcspi200
Integrate function and struct name from ae3xx to
atcspi200 will be more reasonable.

Signed-off-by: Rick Chen <rick@andestech.com>
2017-11-30 09:45:21 +08:00
Rick Chen
41bbb8b333 spi: nds_ae3xx: Rename nds_ae3xx_spi as atcspi200_spi
atcspi200 is Andestech spi ip which is embedded in
AE3XX and AE250 platforms. So rename as atcspi200
will be more reasonable to be used in different
platforms.

Signed-off-by: Rick Chen <rick@andestech.com>
2017-11-30 09:44:09 +08:00
Heinrich Schuchardt
11f12c17d7 rockchip: spi: the symbol for Hertz is Hz
fix typo

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-21 23:57:23 +01:00
Heinrich Schuchardt
042de609ed omap3: spi: the symbol for Hertz is Hz
fix typo

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2017-11-20 20:18:40 -05:00
Bin Meng
ab20107468 spi: ich: Lock down controller settings if required
Some Intel FSP (like Braswell) does SPI lock-down during the call
to fsp_notify(INIT_PHASE_BOOT). But before SPI lock-down is done,
it's bootloader's responsibility to configure the SPI controller's
opcode registers properly otherwise SPI controller driver doesn't
know how to communicate with the SPI flash device.

Rather than passively doing the opcode configuration, let's add a
simple DTS property "intel,spi-lock-down" and let the driver call
the opcode configuration function if required by such FSP.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-27 15:13:47 +08:00
Tuomas Tynkkynen
95688de311 spi: Drop CONFIG_ATMEL_DATAFLASH_SPI
Last user of this option went away in commit:

fdc7718999 ("board: usb_a9263: Update to support DT and DM")

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
2017-10-16 09:42:51 -04:00
Masahiro Yamada
9b643e312d treewide: replace with error() with pr_err()
U-Boot widely uses error() as a bit noisier variant of printf().

This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:

  # define __compiletime_error(message) __attribute__((error(message)))

This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux.  (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)

Let's convert error() into now treewide-available pr_err().

Done with the help of Coccinelle, excluing tools/ directory.

The semantic patch I used is as follows:

// <smpl>
@@@@
-error
+pr_err
 (...)
// </smpl>

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-04 11:59:44 -04:00
Adam Ford
ab0ac27242 spi: davinci_spi: Add da830-spi support for DM
The DM support is already in the driver, so add
da830-spi to the compatible list.

Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
2017-09-29 10:52:20 -04:00
Suresh Gupta
1050998728 spi: fsl_qspi: Copy 16 byte aligned data in TX FIFO
In some of the QSPI controller version, there must be atleast
128bit data available in TX FIFO for any pop operation otherwise
error bit will be set. The code will not make any behavior change
for previous controller as the transfer data size in ipcr register
is still the same.

Patch is tested on LS1046A which do not require 16 bytes aligned and
LS1088A which require 16 bytes aligned data in TX FIFO

Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Anupam Kumar <anupam.kumar_1@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-09-25 15:45:15 +05:30
Suresh Gupta
1c631da459 spi: fsl_qspi: Add controller busy check before new spi operation
It is recommended to check either controller is free to take
new spi action. The IP_ACC and AHB_ACC bits indicates that
the controller is busy in IP or AHB mode respectively.
And the BUSY bit indicates that controller is currently
busy handling a transaction to an external flash device

Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-09-25 12:49:56 +05:30
Peng Fan
994266bdff spi: mxc_spi: support driver model
Add driver model support for mxc spi driver.
Most functions are restructured to be reused by DM and non-DM.
Tested on mx6slevk/mx6qsabresd board.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-09-25 12:47:59 +05:30
rick
7155cd2e6e nds32: spi: Support spi dm driver.
Support spi driver and can detect MX25U1635E flash on AE3XX board.

Verification:

sf probe 0:0 50000000 0
spi_flash_std_probe(sf_Probr.c)
	spi_flash_probe_slave(sf_Probr.c)
	SF: Detected mx25u1635e with page size 256 Bytes, erase size 4 KiB, total 2 MiB
	NDS32 # sf test 0x100000 0x1000
	SPI flash test:
	0 erase: 34 ticks, 117 KiB/s 0.936 Mbps
	1 check: 15 ticks, 266 KiB/s 2.128 Mbps
	2 write: 21 ticks, 190 KiB/s 1.520 Mbps
	3 read: 11 ticks, 363 KiB/s 2.904 Mbps
	Test passed
	0 erase: 34 ticks, 117 KiB/s 0.936 Mbps
	1 check: 15 ticks, 266 KiB/s 2.128 Mbps
	2 write: 21 ticks, 190 KiB/s 1.520 Mbps
	3 read: 11 ticks, 363 KiB/s 2.904 Mbps

Signed-off-by: rick <rick@andestech.com>
2017-09-21 10:30:22 +08:00
Philipp Tomsich
d27c273908 rockchip: spi: Convert to livetree
Update the Rockchip SPI driver to support a live device tree.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18 20:40:35 +02:00
Bin Meng
d2ca80c3d7 x86: ich-spi: Clear atomic preop only when SPI settings are not locked
The atomic preop register can only be written when SPI settings are
not locked, otherwise it's read-only.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-09-02 23:35:55 +08:00
Bin Meng
52dd56ba84 x86: ich-spi: Remove useless assignment in ich_spi_xfer()
In ich_spi_xfer() when the driver presets control fields, control
variable gets assigned twice. Apparently only the last assignment
takes effect. Remove the other one.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-09-02 23:35:55 +08:00
Bin Meng
b42711f90c x86: ich-spi: Move opcode registers configuration to another routine
At present the ICH SPI opcode registers configuration is done in the
ich_spi_remove() routine, a little bit weird but that's how current.
Linux MTD driver works. This changes to move the opcode registers
configuration to a separate routine ich_spi_config_opcode() which
might be called by U-Boot itself as well.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-08-24 11:00:47 +08:00
Bin Meng
3e79141684 x86: ich-spi: Don't read cached lock status
At present the ICH SPI controller driver reads the controller lock
status from its register in the probe routine and saves the lock
status to a member of priv. Later the driver uses the cached status
from priv to judge whether the controller setting is locked and do
different setup.

But such logic is only valid when there is only the SPI controller
driver that touches the SPI hardware. In fact the lock status change
can be trigged outside the driver, eg: during the fsp_notify() call
when Intel FSP is used.

This changes the driver to read the lock status every time when an
SPI transfer is initiated instead of reading the cached one.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-08-24 11:00:47 +08:00
Bin Meng
7d82978927 x86: ich-spi: Remove unnecessary assignment in ich_init_controller()
There is no need to do another assignment to ich7_spi.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-08-24 11:00:47 +08:00
Bin Meng
94bc9177ca x86: ich-spi: Remove spi_write_protect_region()
This routine is not called anywhere.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-08-24 11:00:47 +08:00
Tom Rini
c1b62ba9ca Merge branch 'master' of git://git.denx.de/u-boot-rockchip 2017-08-14 10:40:01 -04:00
Philipp Tomsich
d16120a6de rockchip: spi: enable support for the rk_spi driver for the RK3368
For the RK3368, we can reuse the SPI driver (although we'll have to
eventually investigate whether it can be merged with the
designware_spi.c driver) also used for the RK3288 and RK3399.
This adds the necessary compatible string to support the RK3368.

Note that the assumption that GPLL will be clocked at 594MHz is not
true for the RK3368, but this will not lead to incorrect functioning
(just to a lower-than-expected SPI operating frequency): this has been
documented in the driver, so it doesn't cause any headaches when
someone next needs to touch the clock code of this driver.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-08-13 17:12:34 +02:00
Adam Ford
a41e3e1480 OMAP3_SPI: Kconfig: move OMAP3_SPI out of DM_SPI section.
The OMAP3_SPI driver can work with or without DM_SPI.  Moving this
outside of the #if DM_SPI section allows us to include it on boards
that don't support DM_SPI yet.

Signed-off-by: Adam Ford <aford173@gmail.com>
2017-08-12 19:17:20 -04:00
Tom Rini
ec7483e34e Merge git://git.denx.de/u-boot-fsl-qoriq
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	include/configs/ls1046aqds.h
	include/configs/ls1046ardb.h
2017-08-02 10:52:26 -04:00
Alexander Stein
4df24f2c40 spi: fsl_qspi: Pet watchdog even more
Pet the watchdog once upon each command call (qspi_xfer) and during
each loop iteration in several commands.

This fixes a watchdog reset especially during erase command.

Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-08-01 08:28:56 -07:00
Simon Glass
28a3e5a864 dm: tegra: spi: Convert to livetree
Update the tegra114 spi driver to support a live device tree.

Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Tested-by: Stephen Warren <swarren@nvidia.com>
2017-07-28 12:02:47 -06:00
Simon Glass
000f15fa15 dm: tegra: Convert clock_decode_periph_id() to support livetree
Adjust this to take a device as a parameter instead of a node.

Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Tested-by: Stephen Warren <swarren@nvidia.com>
2017-07-28 12:02:47 -06:00
Patrice Chotard
541cd6e54e spi: stm32_qspi: add clk_get_rate() support
Replace proprietary clock_get() by clk_get_rate()
The stm32_qspi is now "generic" and can be used
by other STM32 SoCs.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Vikas MANOCHA <vikas.manocha@st.com>
2017-07-26 11:28:08 -04:00
Stefano Babic
552a848e4f imx: reorganize IMX code as other SOCs
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.

This change is also coherent with the structure in kernel.

Signed-off-by: Stefano Babic <sbabic@denx.de>

CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Akshay Bhat <akshaybhat@timesys.com>
CC: Ken Lin <Ken.Lin@advantech.com.tw>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Heiko Schocher <hs@denx.de>
CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
CC: Christian Gmeiner <christian.gmeiner@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Patrick Bruenn <p.bruenn@beckhoff.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: "Eric Bénard" <eric@eukrea.com>
CC: Jagan Teki <jagan@amarulasolutions.com>
CC: Ye Li <ye.li@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Adrian Alonso <adrian.alonso@nxp.com>
CC: Alison Wang <b18965@freescale.com>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Martin Donnelly <martin.donnelly@ge.com>
CC: Marcin Niestroj <m.niestroj@grinn-global.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Adam Ford <aford173@gmail.com>
CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
CC: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Soeren Moch <smoch@web.de>
CC: Richard Hu <richard.hu@technexion.com>
CC: Wig Cheng <wig.cheng@technexion.com>
CC: Vanessa Maegima <vanessa.maegima@nxp.com>
CC: Max Krummenacher <max.krummenacher@toradex.com>
CC: Stefan Agner <stefan.agner@toradex.com>
CC: Markus Niebel <Markus.Niebel@tq-group.com>
CC: Breno Lima <breno.lima@nxp.com>
CC: Francesco Montefoschi <francesco.montefoschi@udoo.org>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Scott Wood <oss@buserror.net>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Simon Glass <sjg@chromium.org>
CC: "Andrew F. Davis" <afd@ti.com>
CC: "Łukasz Majewski" <l.majewski@samsung.com>
CC: Patrice Chotard <patrice.chotard@st.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stephen Warren <swarren@nvidia.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: "Álvaro Fernández Rojas" <noltari@gmail.com>
CC: York Sun <york.sun@nxp.com>
CC: Xiaoliang Yang <xiaoliang.yang@nxp.com>
CC: Chen-Yu Tsai <wens@csie.org>
CC: George McCollister <george.mccollister@gmail.com>
CC: Sven Ebenfeld <sven.ebenfeld@gmail.com>
CC: Filip Brozovic <fbrozovic@gmail.com>
CC: Petr Kulhavy <brain@jikos.cz>
CC: Eric Nelson <eric@nelint.com>
CC: Bai Ping <ping.bai@nxp.com>
CC: Anson Huang <Anson.Huang@nxp.com>
CC: Sanchayan Maity <maitysanchayan@gmail.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Patrick Delaunay <patrick.delaunay@st.com>
CC: Gary Bisson <gary.bisson@boundarydevices.com>
CC: Alexander Graf <agraf@suse.de>
CC: u-boot@lists.denx.de
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2017-07-12 10:17:44 +02:00
Philipp Tomsich
6c65577ce6 rockchip: spi: dm: convert fdt_get to dev_read
With the new dev_read functions available, we can convert the rockchip
architecture-specific drivers and common drivers used by these devices
over to the dev_read family of calls.

This change covers the rk_spi.c (SPI driver) used in Rockchip devices.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-07-11 12:13:43 +02:00
Christophe Leroy
f88c431b8a powerpc, 8xx: move SPI driver to drivers/spi/
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
2017-07-08 15:56:03 -04:00
Andy Shevchenko
daab59ac05 avr32: Retire AVR32 for good
AVR32 is gone. It's already more than two years for no support in Buildroot,
even longer there is no support in GCC (last version is heavily patched 4.2.4).

Linux kernel v4.12 got rid of it (and v4.11 didn't build successfully).

There is no good point to keep this support in U-Boot either.

Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2017-07-06 16:17:19 -04:00
Simon Glass
4a7b9ee15e tegra: spi: Wait a little after setting the clocks
For devices that need a delay between SPI transactions we seem to need an
additional delay before the first one if the CPU is running at full speed.
Add this, under control of the existing setting. At present it will only
be enabled with the Chrome OS EC.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-09 13:39:33 -06:00
Simon Glass
279e26f5a3 dm: spi: Convert uclass to livetree
Update the SPI uclass to support a live device tree. Also adjust
spi_slave_ofdata_to_platdata() to accept a device instead of a blob and
offset.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-01 07:03:16 -06:00
Simon Glass
150c5afe5b dm: gpio: Add live tree support
Add support for requesting GPIOs with a live device tree.

This involves adjusting the function signature for the legacy function
gpio_request_by_name_nodev(), so fix up all callers.

Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes to stm32f746-disco.c:
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-01 07:03:10 -06:00
Simon Glass
da409ccc4a dm: core: Replace of_offset with accessor (part 2)
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-01 07:03:04 -06:00
Simon Glass
4af0d7e870 dm: Fix up inclusion of common.h
It is good practice to include common.h as the first header. This ensures
that required features like the DECLARE_GLOBAL_DATA_PTR macro,
configuration options and common types are available.

Fix up some files which currently don't do this. This is necessary because
driver model will soon start using global data and configuration in the
dm/read.h header file, included via dm.h. The gd->fdt_blob value will be
used to access the device tree and CONFIG options will be used to
determine whether to support inline functions in the header file.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-01 07:03:03 -06:00
Simon Glass
a821c4af79 dm: Rename dev_addr..() functions
These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.

In the end we will have:

   1. dev_read_addr...()    - works on devices, supports flat/live tree
   2. devfdt_get_addr...()  - current functions, flat tree only
   3. of_get_address() etc. - new functions, live tree only

All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.

Note this involves changing some dead code - the imx_lpi2c.c file.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-01 07:03:01 -06:00
Peng Fan
41eb8ff5ea spi: kconfig: add soft spi Kconfig entry
Add the Kconfig entry for SOFT_SPI which uses gpio to simulate the
SPI signals. We use it for accessing 74x164 on some i.MX boards.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Stefano Babic <sbabic@denx.de>
2017-05-18 11:24:34 +02:00
Stefan Roese
4759dffe23 spi: ich: Configure SPI BIOS parameters for Linux upon U-Boot exit
This patch adds a remove function to the Intel ICH SPI driver, that will
be called upon U-Boot exit, directly before the OS (Linux) is started.
This function takes care of configuring the BIOS registers in the SPI
controller (similar to what a "standard" BIOS or coreboot does), so that
the Linux MTD device driver is able to correctly read/write to the SPI
NOR chip. Without this, the chip is not detected at all.

Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Jagan Teki <jteki@openedev.com>
2017-05-17 17:13:06 +08:00
Tom Rini
25eaa28801 omap: spi: Drop CONFIG_OMAP3_SPI_D0_D1_SWAPPED support
This particular quirk is not enabled in any config files today.  It does
however exist and is handled correctly in device trees and via
CONFIG_DM_SPI.  So we drop the symbol now and add a comment to indicate
that any (new) boards that require this quirk need to enable DM_SPI
instead.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-15 10:40:01 -04:00
Jakob Unterwurzacher
cdeb4d780a rockchip: spi: enable support for the rk_spi driver for the RK3399
The existing Rockchip SPI (rk_spi.c) driver also matches the hardware
block found in the RK3399.  This has been confirmed both with SPI NOR
flashes and general SPI transfers on the RK3399-Q7 for SPI1 and SPI5.

This change adds the 'rockchip,rk3399-spi' string to its compatible
list to allow reuse of the existing driver.

X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
2017-05-10 13:37:21 -06:00
Philipp Tomsich
9fc354e246 rockchip: spi: rewrite rkspi_set_clk for a more conservative baudrate setting
The baudrate in rkspi was calculated by using an integer division
(which implicitly discarded any fractional result), then rounding to
an even number and finally clamping to 0xfffe using a bitwise AND
operator.  This introduced two issues:
1) for very small baudrates (overflowing the 0xfffe range), the
   bitwise-AND generates rather random-looking (wildly varying)
   actual output bitrates
2) for higher baudrates, the calculation tends to 'err towards a
   higher baudrate' with the actual error increasing as the dividers
   become very small. E.g., with a 99MHz input clock, a request
   for a 20MBit baudrate (99/20 = 4.95), a 24.75 MBit would be use
   (which amounts to a 23.75% error)... for a 34 MBit request this
   would be an actual outbout of 49.5 Mbit (i.e. a 45% error).

This change rewrites the divider selection (i.e. baudrate calculation)
by making sure that
a) for the normal case: the largest representable baudrate below the
   requested rate will be chosen;
b) for the denormal case (i.e. when the divider can no longer be
   represented), the lowest representable baudrate is chosen.

Even though the denormal case (b) may be of little concern in real
world applications (even with a 198MHz input clock, this will only
happen at below approx. 3kHz/3kBit), our board-verification team kept
complaining.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
2017-05-10 13:37:21 -06:00
Philipp Tomsich
bd37671434 rockchip: spi: rk_spi: dynamically select an module input rate
The original clock/bitrate selection code for the rk_spi driver was a
bit limited, as it always selected a 99MHz input clock rate (which
would allow for a maximum bitrate of 49.5MBit/s), but returned -EINVAL
if a bitrate higher than 48MHz was requested.

To give us better control over the bitrate (i.e. add more operating
points, especially at "higher" bitrate---such as above 9MBit/s), we
try to choose 4x the maximum frequency (clamped to 50MBit) from the
DTS instead of 99MHz... for most use-cases this will yield a frequency
of 198MHz, but is flexible to go beyond this in future configurations.

This also rewrites the check to allow frequencies of up to half the
SPI module rate as bitrates and then clamps to whatever the DTS allows
as a maximum (board-specific) frequency and does away with the -EINVAL
when trying to select a bitrate (for cases that exceeded the hard
limit) and instead consistently clamps to the lower of the hard limit,
the soft limit for the SPI bus (from the DTS) or the soft limit for
the SPI slave device.

This replaces
  "rockchip: spi: rk_spi: select 198MHz input to the SPI module for the RK3399"
  "rockchip: spi: rk_spi: improve clocking code for the RK3399"
from earlier versions of this series.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-05-10 13:37:21 -06:00
Vikas Manocha
890bafd752 stm32f7: use clock driver to enable qspi controller clock
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
2017-05-08 11:38:41 -04:00
Suniel Mahesh
2f54205829 drivers: spi: Remove duplicate .probe method
.probe method has been assigned twice when declaring
a driver with U_BOOT_DRIVER(). Removed one of them.
Here is the last commit which had the duplicate entry:
"spi: omap3: Convert to driver model"
(sha1: 77b8d04854)

Signed-off-by: Suniel Mahesh <suniel.spartan@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-05-03 11:52:16 +05:30
Moritz Fischer
ac6991fb5f zynq: spi: Honour the activation / deactivation delay
This is not currently implemented. Add support for this so that the
Chrome OS EC can be used reliably.

Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Acked-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-05-03 11:03:04 +05:30
Wenyou Yang
61a77ce1d5 spi: atmel: check GPIO validity before using cs_gpios
Before using the cs_gpio, check if the GPIO is valid or not.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-05-03 10:58:54 +05:30
Tom Rini
ea3310e8aa Blackfin: Remove
The architecture is currently unmaintained, remove.

Cc: Benjamin Matthews <mben12@gmail.com>
Cc: Chong Huang <chuang@ucrobotics.com>
Cc: Dimitar Penev <dpn@switchfin.org>
Cc: Haitao Zhang <hzhang@ucrobotics.com>
Cc: I-SYST Micromodule <support@i-syst.com>
Cc: M.Hasewinkel (MHA) <info@ssv-embedded.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Martin Strubel <strubel@section5.ch>
Cc: Peter Meerwald <devel@bct-electronic.com>
Cc: Sonic Zhang <sonic.adi@gmail.com>
Cc: Valentin Yakovenkov <yakovenkov@niistt.ru>
Cc: Wojtek Skulski <info@skutek.com>
Cc: Wojtek Skulski <skulski@pas.rochester.edu>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-05 13:52:01 -04:00
Stefan Roese
706865afe5 dm: core: Add flags parameter to device_remove()
This patch adds the flags parameter to device_remove() and changes all
calls to this function to provide the default value of DM_REMOVE_NORMAL
for "normal" device removal.

This is in preparation for the driver specific pre-OS (e.g. DMA
cancelling) remove support.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
2017-04-04 20:15:10 -06:00
Suresh Gupta
38a5c57ac5 spi: fsl_qspi: Add support for single chip select
SOC’s like LS1012A has only one chip select signal for QSPI flash.
Avoid scanning other flash.

Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-03-28 09:10:12 -07:00
Jean-Jacques Hiblot
b06a381a69 drivers: ti_qspi: use syscon to get the address ctrl_mod_mmap register
We used to get the address of the optionnal ctrl_mod_mmap register as the
third memory range of the "reg" property. the linux driver moved to use a
syscon instead. In order to keep the DTS as close as possible to that of
linux, we move to using a syscon as well.

If SYSCON is not supported, the driver reverts to the old way of getting
the address from the 3rd memory range

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2017-03-22 07:27:19 -06:00
Simon Glass
e160f7d430 dm: core: Replace of_offset with accessor
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-02-08 06:12:14 -07:00
Michael Kurz
d4363baada ARM: SPI: stm32: add stm32f746 qspi driver
This patch adds support for the QSPI IP found in stm32f7 devices.

Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
2017-01-28 14:04:50 -05:00
Jagan Teki
68e7999ba9 spi: Zap cf_qspi driver and related code
Dropped becuase
- driver not used any board.
- no dm conversion.

Cc: Angelo Dureghello <angelo@sysam.it>
Cc: Richard Retanubun <richardretanubun@ruggedcom.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Acked-by: Angelo Dureghello <angelo@sysam.it>
2017-01-15 18:29:04 +01:00
Jagan Teki
ee86e0d2fe spi: Zap ep93xx_spi driver and related code
Dropped becuase
- driver and related configs not used any board.
- no dm conversion.

Cc: Heiko Schocher <hs@denx.de>
Cc: Sergey Kostanbaev <sergey.kostanbaev@gmail.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
2017-01-13 22:47:14 +01:00
Vignesh R
b63b46313e spi: cadence_qspi_apb: Use 32 bit indirect read transaction when possible
According to Section 11.15.4.9.1 Indirect Read Controller of K2G SoC
TRM SPRUHY8D[1], the external master is only permitted to issue 32-bit
data interface reads until the last word of an indirect transfer
So, make sure that QSPI indirect reads are 32 bit sized except for the
final read. If the rxbuf is unaligned then use bounce buffer, so that
readsl() can be used instead of readsb() to avoid non 32-bit accesses.

[1]www.ti.com/lit/ug/spruhy8d/spruhy8d.pdf

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-01-04 16:38:35 +01:00
Vignesh R
57897c13de spi: cadence_qspi_apb: Use 32 bit indirect write transaction when possible
According to Section 11.15.4.9.2 Indirect Write Controller of K2G SoC
TRM SPRUHY8D[1], the external master is only permitted to issue 32-bit
data interface writes until the last word of an indirect transfer
otherwise indirect writes is known to fails sometimes. So, make sure
that QSPI indirect writes are 32 bit sized except for the last write. If
the txbuf is unaligned then use bounce buffer to avoid data aborts.

So, now that the driver uses bounce_buffer, enable CONFIG_BOUNCE_BUFFER
for all boards that use Cadence QSPI driver.

[1]www.ti.com/lit/ug/spruhy8d/spruhy8d.pdf

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-01-04 16:38:12 +01:00
Jagan Teki
cb71c6d854 spi: Zap armada100_spi.c and env
armada100_spi.c and related env is zapping becuase
of "no DM conversion".

Cc: Ajay Bhargav <ajay.bhargav@einfochips.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
2016-12-21 12:18:47 +01:00
Jagan Teki
353f6a770f spi: Zap mpc52xx_spi.c, config and related code
armada100_spi.c, related config options and related codes
are zapping becuase of "no DM conversion".

Cc: Werner Pfister <Pfister_Werner@intercontrol.de>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-21 12:14:37 +01:00
Phil Edworthy
6d72810c66 spi: cadence_qspi: Move DT prop code to match layout
Move the code to read the "sram-size" property into the other code
that reads properties from the node, rather than the SF subnode.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:28 +01:00
Phil Edworthy
22e63ff3a2 spi: cadence_qspi: Fix CS timings
The Cadence QSPI controller has specified overheads for the various CS
times that are in addition to those programmed in to the Device Delay
register. The overheads are different for the delays.

In addition, the existing code does not handle the case when the delay
is less than a SCLK period.

This change accurately calculates the additional delays in Ref clocks.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:27 +01:00
Phil Edworthy
3c56953219 spi: cadence_qspi: Remove returns from end of void functions
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:27 +01:00
Phil Edworthy
7d403f284c spi: cadence_qspi: Use spi mode at the point it is needed
Instead of extracting mode settings and passing them as separate
args to another function, just pass the SPI mode as an arg.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:27 +01:00
Phil Edworthy
7e76c4b08a spi: cadence_qspi: Clean up the #define names
A lot of the #defines are for single bits in a register, where the
name has _MASK on the end. Since this can be used for both a mask
and the value, remove _MASK from them.

Whilst doing so, also remove the unnecessary brackets around the
constants.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:27 +01:00
Phil Edworthy
db37cc9c39 spi: cadence_qspi: Use #define for bits instead of bit shifts
Most of the code already uses #defines for the bit value, rather
than the shift required to get the value. This changes the remaining
code over.

Whislt at it, fix the names of the "Rd Data Capture" register defs.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:27 +01:00
Phil Edworthy
0ceb4d9e9a spi: cadence_qspi: Better debug information on the SPI clock rate
Show what the output clock rate actually is.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:27 +01:00
Phil Edworthy
32068c42a7 spi: cadence_qspi: Fix baud rate calculation
With the existing code, when the requested SPI clock rate is near
to the lowest that can be achieved by the hardware (max divider
of the ref clock is 32), the generated clock rate is wrong.
For example, with a 50MHz ref clock, when asked for anything less
than a 1.5MHz SPI clock, the code sets up the divider to generate
25MHz.

This change fixes the calculation.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:27 +01:00
Phil Edworthy
cc80a897e4 spi: cadence_qspi: Fix clearing of pol/pha bits
Or'ing together bit positions is clearly wrong.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:57:27 +01:00
Simon Glass
1b7c28f514 spi: Add error checking for invalid bus widths
At present an invalid bus width prints a message but does not return an
error. This is the opposite of the correct behaviour. Adjust it to avoid
code bloat in the common case, and avoid hard-to-debug failure in the
uncommon case.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-12-15 16:38:30 +01:00
Nishanth Menon
3891a54f47 ARM: DRA7x/AM57xx: Get rid of CONFIG_AM57XX
CONFIG_AM57XX is just an unnecessary macro that is redundant given So,
remove the same instead of spreading through out the u-boot source
code and getting in the way to maintain common code for DRA7x family.

Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-03 13:21:11 -05:00
Simon Glass
28f9885875 spi: Add a debug() on bind failure
This is an uncommon error but we may as well have a debug() message when
it happens.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-11-25 17:59:30 -07:00
Simon Glass
b42524744d rockchip: spi: Honour the deactivation delay
This is not currently implemented. Add support for this so that the Chrome
OS EC can be used on jerry.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-11-25 17:59:30 -07:00
Simon Glass
6e019c4f28 rockchip: spi: Add support for of-platdata
Allow this driver to be used with of-platdata on rk3288.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-11-25 17:59:30 -07:00
Simon Glass
71634f289d spi: Add of-platdata support to SPI and SPI flash
Some boards may want to use these subsystems with of-platdata in SPL. Add
support for this by avoiding any device tree access in this case.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-11-25 17:59:30 -07:00
Chris Packham
ebfa18cb3d spi: kirkwood_spi: implement mvebu_spi_set_mode()
Set the appropriate bits in the interface config register based
on the SPI_ mode flags.

Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
2016-11-18 13:04:52 +05:30
Vignesh R
948b8bbd5f spi: ti_qspi: Fix baudrate divider calculation
Fix the divider calculation logic to choose a value so that the
resulting baudrate is either equal to or closest possible baudrate less
than the requested value. While at that, cleanup ti_spi_set_speed().

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2016-11-13 15:54:37 -05:00
Wenyou Yang
0eafd4b776 dm: at91: Add driver model support for the spi driver
Add driver model support while retaining the existing legacy code.
This allows the driver to support boards that have converted to
driver model as well as those that have not.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
2016-10-28 18:37:15 +02:00
Simon Glass
df87e6b1b8 libfdt: Sync fdt_for_each_subnode() with upstream
The signature for this macro has changed. Bring in the upstream version and
adjust U-Boot's usages to suit.

Signed-off-by: Simon Glass <sjg@chromium.org>
Update to drivers/power/pmic/palmas.c:
Signed-off-by: Keerthy <j-keerthy@ti.com>

Change-Id: I6cc9021339bfe686f9df21d61a1095ca2b3776e8
2016-10-13 14:10:32 -06:00
Tom Rini
711b534120 Merge git://git.denx.de/u-boot-fsl-qoriq
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	include/configs/ls1021aqds.h
	include/configs/ls1021atwr.h
2016-10-12 08:29:42 -04:00
Robert P. J. Day
fc0b5948e0 Various, accumulated typos collected from around the tree.
Fix various misspellings of:

 * deprecated
 * partition
 * preceding,preceded
 * preparation
 * its versus it's
 * export
 * existing
 * scenario
 * redundant
 * remaining
 * value
 * architecture

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2016-10-06 20:57:40 -04:00
York Sun
3c6b1767c2 spi: fsl_qspi: Preserve endianness of QSPI MCR
The endianness can be changed by RCW + PBI sequence. It may have
other than power on reset value.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Yuan Yao <yao.yuan@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-10-06 14:28:32 -07:00
Stefan Roese
3fda4ef395 spi: Add driver for Marvell Armada 3700 SoC
The SPI IP core in the Marvell Armada 3700 is similar to the one in the
other Armada SoCs. But the differences are big enough that it makes
sense to introduce a new driver instead of cluttering the old
kirkwood driver with #ifdef's.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-09-27 17:29:52 +02:00
Masahiro Yamada
1221ce459d treewide: replace #include <asm/errno.h> with <linux/errno.h>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content.  (both just wrap <asm-generic/errno.h>)

Replace all include directives for <asm/errno.h> with <linux/errno.h>.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-23 17:55:42 -04:00
Tom Rini
19d051a2b7 Merge branch 'master' of git://git.denx.de/u-boot-spi 2016-09-22 11:36:45 -04:00
Jagan Teki
21b1dd18f1 spi: Kconfig: Move FSL_QSPI entry to non-dm place
Since FSL_QSPI driver still supporting non-dm code
better to move the Kconfig from DM undefined place.

Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-09-22 14:16:28 +05:30
Michal Simek
5f647c2284 spi: zynq: Use variable to remove u32 to u64 conversions
Current code generates warning when it is compiled for arm64:
Warnings:
In file included from drivers/spi/zynq_spi.c:14:0:
drivers/spi/zynq_spi.c: In function ‘zynq_spi_init_hw’:
drivers/spi/zynq_spi.c:95:9: warning: large integer implicitly truncated
to unsigned type [-Woverflow]
  writel(~ZYNQ_SPI_ENR_SPI_EN_MASK, &regs->enr);
         ^
./arch/arm/include/asm/io.h:146:34: note: in definition of macro
‘writel’
 #define writel(v,c) ({ u32 __v = v; __iowmb(); __arch_putl(__v,c); __v;
})
                                  ^
drivers/spi/zynq_spi.c: In function ‘zynq_spi_release_bus’:
drivers/spi/zynq_spi.c:177:9: warning: large integer implicitly
truncated to unsigned type [-Woverflow]
  writel(~ZYNQ_SPI_ENR_SPI_EN_MASK, &regs->enr);
         ^
./arch/arm/include/asm/io.h:146:34: note: in definition of macro
‘writel’
 #define writel(v,c) ({ u32 __v = v; __iowmb(); __arch_putl(__v,c); __v;
})
                                  ^
This patch is using one variable to do conversion via u32 variable.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-09-22 07:33:20 +02:00
Jagan Teki
08fe9c294f spi: Use mode for rx mode flags
Make rx mode flags as generic to spi, earlier mode_rx is
maintained separately because of some flash specific code.

Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-09-22 01:02:28 +05:30
Vignesh R
28b69f6488 spi: ti_qspi: Remove unnecessary udelay for AM437x
This udelay() was added as an HACK and is no longer required. All
read/write/erase operations work fine even without this delay. Hence,
remove the udelay() call.

Tested read/write/erase operation on AM437x SK. Also tested QSPI Boot.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-09-22 00:58:26 +05:30
Vignesh R
260368507a spi: ti_qspi: use 128 bit transfer mode when writing to flash
TI QSPI has four 32 bit data registers which can be used to transfer 16
bytes of data at once. The register group QSPI_SPI_DATA_REG_3,
QSPI_SPI_DATA_REG_2, QSPI_SPI_DATA_REG_1 and QSPI_SPI_DATA_REG is
treated as a single 128-bit word for shifting data in and out. The bit
at QSPI_SPI_DATA_REG_3[31] position is the first bit to be shifted out
in case of 128 bit transfer mode. Therefore the first byte to be written
to flash should be at QSPI_SPI_DATA_REG_3[31-25] position.
Instead of writing 1 byte at a time when interacting with SPI NOR flash,
make use of all the four registers so that 16 bytes can be transferred
in one go.

With this patch, the flash write speed increases from ~250KBs/ to
~650KB/s on DRA74 EVM.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-09-22 00:58:26 +05:30
Lad, Prabhakar
d2998286fc spi: zynq_spi: Fix infinite looping while xfer
During spi transfer, for example:
sspi 1:1.0 8 ff

the rx_len values will  be:
rx_len = 0
rx_len = 4294967295

This caused a busy looping during xfer, this patch fixes it
by adding a check while reading the rx fifo

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-09-22 00:58:26 +05:30
Stephen Warren
4832c7f5f7 spi: tegra: fix hang in set_mode()
In tegra20_slink.c, the set_mode() function may be executed before the
SPI bus is claimed the first time, and hence the clocks to the SPI
controller may not be running. If so, any register read/write at this
time will hang the CPU. Fix this by ensuring the clock is running as soon
as the driver is probed. This is observed on the Tegra30 Beaver board.

Apply the same clock initialization fix to all other Tegra SPI drivers so
that if set_mode() is ever implemented there, the same bug will not appear.
Note that tegra114_spi.c already operates in this fashion.

The clock manipulation code is copied from claim_bus() to probe() rather
than moved. This ensures that any calls to set_speed() take effect; the
clock can't be set once during probe and left unchanged.

Fixes: 5cb1b7b395 ("spi: tegra20: Add support for mode selection")
Cc: Mirza Krak <mirza.krak@hostmobility.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-08-25 15:35:03 -07:00
Chin Liang See
5405817a6e spi: cadence_qspi_apb: Ensure baudrate doesn't exceed max value
Ensuring the baudrate divisor value doesn't exceed the max value
in the calculation.It will be capped at max value to ensure the
correct value being written into the register.

Example of the existing bug is when calculated div = 16. After and
with the mask, the value written to register is actually 0 (register
field for baudrate divisor). With this fix, the value written is now
15 which is max value for baudrate divisor.

Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jteki@openedev.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
2016-08-07 21:54:21 +02:00
Yunhui Cui
04e5c6d9cc driver: spi: fsl-qspi: remove compile Warnings
Warnins log:
drivers/spi/fsl_qspi.c: In function ‘qspi_ahb_read’:
drivers/spi/fsl_qspi.c:400:16: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
  memcpy(rxbuf, (u8 *)(priv->cur_amba_base + priv->sf_addr), len);

Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-08-02 09:45:13 -07:00
Vignesh R
a6f56ad1ee spi: ti_qspi: dra7xx: Add support to use 76.8MHz clock
According to AM572x DM SPRS953A, QSPI bus speed can be 76.8MHz, update
the driver to use the same.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
2016-07-30 00:15:00 +05:30
Vignesh R
fee3b6af90 spi: ti_qspi: Remove delay in read path for dra7xx
As per commit b545a98f5d ("spi: ti_qspi: Add delay
for successful bulk erase) says its added to meet bulk erase timing
constraints. But bulk erase is a cmd to flash and delay in read path
does not make sense. Morever, testing on DRA74/DRA72 evm has shown that
this delay is no longer required.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
2016-07-30 00:15:00 +05:30
Vignesh R
c595a28530 spi: ti_qspi: Fix compiler warning when DEBUG macro is set
clk_div is uninitialized at the beginning of ti_spi_set_speed(), move
debug() print after clk_div calculation to avoid compiler warning and to
have proper value of clk_div printed during debugging.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
2016-07-30 00:15:00 +05:30
Vignesh R
69eeefaa06 spi: ti_qspi: Fix failure on multiple READ_ID cmd
Populating QSPI_RD_SNGL bit(0x1) in priv->cmd means that value
QSPI_INVAL (0x4) is not written to CMD field of QSPI_SPI_CMD_REG in
ti_qspi_cs_deactivate(). Therefore CS is never deactivated between
successive READ ID which results in sf probe to fail.
Fix this by not populating priv->cmd with QSPI_RD_SNGL and OR it wih
priv->cmd as required (similar to the convention followed in the
driver).

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
2016-07-30 00:15:00 +05:30
Simon Glass
911954859d dm: Use dm_scan_fdt_dev() directly where possible
Quite a few places have a bind() method which just calls dm_scan_fdt_dev().
We may as well call dm_scan_fdt_dev() directly. Update the code to do this.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-27 14:15:54 -06:00
Simon Glass
2e3f1ff63f dm: Convert users from dm_scan_fdt_node() to dm_scan_fdt_dev()
This new function is more convenient for callers, and handles pre-relocation
situations automatically.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-27 14:15:07 -06:00
Vignesh R
96907c0fe5 dm: spi: Read default speed and mode values from DT
In case of DT boot, don't read default speed and mode for SPI from
CONFIG_*, instead read from DT node. This will make sure that boards
with multiple SPI/QSPI controllers can be probed at different
bus frequencies and SPI modes.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:34 +05:30
Vignesh R
2372e14f19 spi: cadence_quadspi: Enable QUAD mode based on DT data
Instead of relying on CONFIG_SPI_FLASH_QUAD to be defined to enable QUAD
mode, make use of mode_rx field of dm_spi_slave_platdata to determine
whether to enable or disable QUAD mode. This is necessary to support
muliple SPI controllers where one of them may not support QUAD mode.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:33 +05:30
Vignesh R
dac3bf20fb spi: cadence_qspi_apb: Support 32 bit AHB address
AHB address can be as long as 32 bit, hence remove the
CQSPI_REG_INDIRECTRDSTARTADDR mask. Since AHB address is passed from DT
and read as u32 value, it anyway does not make sense to mask upper bits.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:32 +05:30
Vignesh R
192bb756dc spi: davinci_spi: Convert to driver to adapt to DM
Convert davinci_spi driver so that it complies with SPI DM framework.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:30 +05:30
Anatolij Gustschin
c8864d7209 spi: spi-uclass: fix typo in debug output
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-06 12:40:32 +05:30
Praneeth Bajjuri
8dfd6e2129 driver: qspi: correct QSPI disable CS reset value
Correcting QSPI disable/unselect CS reset value.
CTRL_CORE_CONTROL_IO_2: QSPI_MEMMAPPED_CS[10:8]

This is not causing any issue, but its better
to untouch the reserved bits.

Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
2016-07-01 17:42:53 -04:00
Stephen Warren
135aa95002 clk: convert API to match reset/mailbox style
The following changes are made to the clock API:
* The concept of "clocks" and "peripheral clocks" are unified; each clock
  provider now implements a single set of clocks. This provides a simpler
  conceptual interface to clients, and better aligns with device tree
  clock bindings.
* Clocks are now identified with a single "struct clk", rather than
  requiring clients to store the clock provider device and clock identity
  values separately. For simple clock consumers, this isolates clients
  from internal details of the clock API.
* clk.h is split so it only contains the client/consumer API, whereas
  clk-uclass.h contains the provider API. This aligns with the recently
  added reset and mailbox APIs.
* clk_ops .of_xlate(), .request(), and .free() are added so providers
  can customize these operations if needed. This also aligns with the
  recently added reset and mailbox APIs.
* clk_disable() is added.
* All users of the current clock APIs are updated.
* Sandbox clock tests are updated to exercise clock lookup via DT, and
  clock enable/disable.
* rkclk_get_clk() is removed and replaced with standard APIs.

Buildman shows no clock-related errors for any board for which buildman
can download a toolchain.

test/py passes for sandbox (which invokes the dm clk test amongst
others).

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-06-19 17:05:55 -06:00
Purna Chandra Mandal
e19b900457 spi: pic32_spi: add SPI master driver for PIC32 SoC.
This driver implements SPI protocol in master mode to communicate
with the SPI device connected on SPI bus. It handles /CS explicitly
by controlling respective pin as gpio ('cs-gpios' property in dt node)
and uses PIO mode for SPI transaction. It is configurable based
on driver-model only.

Cc: Jagan Teki <jteki@openedev.com>
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-06-10 12:31:12 +02:00
Tom Rini
fc15b9beed Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2016-05-24 13:42:03 -04:00
Tom Rini
d7d0003112 Merge branch 'master' of git://git.denx.de/u-boot-mips 2016-05-23 11:51:37 -04:00
Martin Hejnfelt
5f89a15e16 omap3: Fix SPI registers on am33xx and am43xx
When the base registers are read from device tree the base is not
0x48030100 as the driver expects, but 0x48030000, resulting in
non functioning SPI. To deal with this, use same idea as how this
is done in the linux kernel (drivers/spi/spi-omap2-mcspi.c) and
add a structure with a field that is used to shift the registers
on these systems.

v2: Fixed commit subject line to correct cpu

Signed-off-by: Martin Hejnfelt <mh@newtec.dk>
2016-05-23 11:50:22 -04:00
Wills Wang
5fabf2e7da ath79: spi: Remove the explicit pinctrl setting
The correct pinctrl is handled automatically so we don't need to do it in
the driver.

Signed-off-by: Wills Wang <wills.wang@live.com>
2016-05-21 01:36:37 +02:00
Wills Wang
b85dc46072 drivers: spi: add spi support for QCA/Atheros ath79 SOCs
This patch add a compatible spi driver for ath79 series SOC.

Signed-off-by: Wills Wang <wills.wang@live.com>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-05-21 01:25:50 +02:00
Yuan Yao
febffe8dd1 spi: fsl_qspi: Enable Spansion S25FS-S family flashes
The flash type of LS2085AQDS QSPI is S25FS256S. It has special write
any device register command and read any device register command.
This patch enable support for those commands.

Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-18 08:51:16 -07:00
Yuan Yao
4e14741833 spi: fsl_qspi: Assign AMBA mem according CS num in dts
QSPI controller automatic enable the chipselect signal according the
dest AMBA memory address. Now we distribute the AMBA memory zone
averagely to every chipselect slave device according chipselect
numbers got from dts node.

Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-18 08:51:06 -07:00
Yuan Yao
bf9bffa978 spi: fsl_qspi: Fix issues on arm64
The address value and size value get from dts "reg" property have
type of u64 on arm64. If we assign those values to "u32" variables,
driver can't work correctly. Converting the type of those variables
to fdt_xxx_t.

Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-18 08:50:48 -07:00
Peng Fan
7a3eff4ce9 dm: spi: introduce dm api
Introduce dm_spi_claim_bus, dm_spi_release_bus and dm_spi_xfer
Convert spi_claim_bus, spi_release_bus and spi_xfer to use
the new API.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jagan Teki <jteki@openedev.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Peng Fan
102412c415 dm: spi: soft_spi: switch to use linux compatible string
1. Support compatible string "spi-gpio" which is used by Linux
   Linux use different bindings, so use UBOOT_COMPAT and
   LINUX_COMPAT to differentiate them.
2. Introduce SPI_MASTER_NO_RX and SPI_MASTER_NO_TX to handle
   no rx or no tx case.
3. Tested on i.MX6 UltraLite board with 74LV595 spi-gpio chip.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Peng Fan
b6d54d5273 dm: spi: soft_spi bug fix
When doing xfer, should use device->parent, but not device
When doing bit xfer, should use "!!(tmpdout & 0x80)", but not
"(tmpdout & 0x80)"

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Marek Vasut
5a824c493a mtd: cqspi: Simplify indirect read code
The indirect read code is a pile of nastiness. This patch replaces
the whole unmaintainable indirect read implementation with the one
from upcoming Linux CQSPI driver, which went through multiple rounds
of thorough review and testing. All the patch does is it plucks out
duplicate ad-hoc code distributed across the driver and replaces it
with more compact code doing exactly the same thing. There is no
speed change of the read operation.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Jagan Teki <jteki@openedev.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vignesh R <vigneshr@ti.com>
2016-05-06 18:41:49 +02:00
Marek Vasut
26da6353e1 mtd: cqspi: Simplify indirect write code
The indirect write code is buggy pile of nastiness which fails horribly
when the system runs fast enough to saturate the controller. The failure
results in some pages (256B) not being written to the flash. This can be
observed on systems which run with Dcache enabled and L2 cache enabled,
like the Altera SoCFPGA.

This patch replaces the whole unmaintainable indirect write implementation
with the one from upcoming Linux CQSPI driver, which went through multiple
rounds of thorough review and testing. While this makes the patch look
terrifying and violates all best-practices of software development, all
the patch does is it plucks out duplicate ad-hoc code distributed across
the driver and replaces it with more compact code doing exactly the same
thing.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Jagan Teki <jteki@openedev.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vignesh R <vigneshr@ti.com>
2016-05-06 18:41:49 +02:00
Stefan Roese
9fc56631a4 spi: kirkwood_spi: Add support for multiple chip-selects on MVEBU
Currently only chip-select 0 is supported by the kirkwood SPI driver.
The Armada XP / 38x SoCs also use this driver and support multiple chip
selects. This patch adds support for multiple CS on MVEBU.

The register definitions are restructured a bit with this patch. Grouping
them to the corresponding registers.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-04-06 15:38:56 +02:00
Stefan Roese
951f1b5f37 spi: kirkwood_spi.c: Add compatible match ID for Armada 375
This enables this driver for the Marvell Armada 375 SoC.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviwer-by: Jagan Teki <jteki@openedev.com>
2016-04-04 11:21:27 +02:00
Jagan Teki
41bccb8142 spi: omap3: Fix multiple definition of 'priv'
Global definition of priv seems no-sense to use it
for non-dm case and pass the pointer to functions
which are common to both dm and non-dm.

So, fix this by removing omap3_spi_slave from non-dm
and make visible to omap3_spi_priv for both dm and non-dm.

Cc: Christophe Ricard <christophe-h.ricard@st.com>
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-03-15 14:50:09 -04:00
Jagan Teki
77b8d04854 spi: omap3: Convert to driver model
After this conversion the driver will able to support both dm and non-dm
and code is more extensible like we can remove the non-dm part simply
without touching anycode if all the boards which are using this driver
become dm driven.

Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Christophe Ricard <christophe-h.ricard@st.com>
Tested-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
[Set priv->wordlen, Add Kconfig entry and file credit for dm conversion]
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
2016-03-14 22:46:28 +05:30
Jagan Teki
03661d85f0 spi: omap3: Make local functions as static
Attach static on local defined functions.

Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
2016-03-14 22:46:28 +05:30
Jagan Teki
682c172350 spi: omap3: Move headers code inside the driver
Header file have macro's and register definition and some unneeded
function proto types which becomes tunned further in future patches
and entire driver code resides in one file for more readability.

Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
[Fixes on code styles, Remove omap3_spi_txrx|write|read in header]
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
2016-03-14 22:46:16 +05:30
Lokesh Vutla
e6601df8ac dm: ti_qspi: Fix conversion of address to a pointer
TI QSPI driver directly typecasts fdt_addr_t to a pointer. This is
not strictly correct, as it gives a build warning when fdt_addr_t is u64.
So, use map_physmem for a proper typecasts.

This is inspired by commit 167efe01bc ("dm: ns16550: Use an address
instead of a pointer for the uart base")

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
2016-03-12 19:55:42 +05:30
Christophe Ricard
674f3609aa spi: spi-uclass: Set slave wordlen with SPI_DEFAULT_WORDLEN
In some case wordlen may not be set. Use SPI_DEFAULT_WORDLEN as default.

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-02-23 16:14:46 +05:30
Christophe Ricard
3963919e5b spi: omap3: Remove unused variable irqstatus in omap3_spi_txrx
Remove unused variable irqstatus in omap3_spi_txrx

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-02-23 16:14:46 +05:30
Mugunthan V N
518b0afc33 spi: ti_qspi: compile out spi_flash_copy_mmap when CONFIG_DMA is defined
When CONFIG_DMA is defined the default spi_flash_copy_mmap() can
handle dma memory copy, so compile out spi_flash_copy_mmap() from
ti_qspi driver when CONFIG_DMA config is defined.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-02-23 16:14:46 +05:30
Bin Meng
3e389d8ba6 dm: pch: Rename get_sbase op to get_spi_base
Spell out 'sbase' to 'spi_base' so that it looks clearer.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2016-02-05 12:47:21 +08:00
Bin Meng
6e670b5c4d spi: ich: Change PCHV_ to ICHV_
The ICH SPI controller supports two variants, one of which is ICH7
compatible and the other is ICH9 compatible. Change 'pch_version'
to 'ich_version' to better match its original name.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Tested-by: Simon Glass <sjg@chromium.org>
2016-02-05 12:47:20 +08:00
Bin Meng
1f9eb59d27 spi: ich: Use compatible strings to distinguish controller version
At present ich spi driver gets the controller version information via
pch, but this can be simply retrieved via spi node's compatible string.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Tested-by: Simon Glass <sjg@chromium.org>
2016-02-05 12:47:20 +08:00
Bin Meng
9eb4339ba4 spi: ich: Some clean up
This cleans up the ich spi driver a little bit:
- Remove struct ich_spi_slave that is not referenced anywhere
- Remove ending period in some comments
- Move struct ich_spi_platdata and struct ich_spi_priv to ich.h
- Add #ifndef _ICH_H_ .. in ich.h

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-02-05 12:47:20 +08:00
Tom Rini
cd85bec36d Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2016-01-27 15:05:36 -05:00
Gong Qianyu
940d2b89bf spi: fsl_qspi: Fix qspi_op_rdsr memcpy issue
In current driver, we always copy 4 bytes to the dest memory.
Actually the dest memory may be shorter than 4 bytes.
Add an argument to indicate the dest memory length.
Avoid writing memory outside of the bounds.

Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:28:31 -08:00
Gong Qianyu
5207014deb spi: fsl_qspi: Fix qspi_op_rdid memcpy issue
In current driver everytime we memcpy 4 bytes to the dest memory
regardless of the remaining length.
This patch adds checking the remaining length before memcpy.
If the length is shorter than 4 bytes, memcpy the actual length of data
to the dest memory.

Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:28:04 -08:00
Gong Qianyu
c2a4cb17b4 spi: fsl_qspi: fix compile warning for 64-bit platform
This patch fixes the following compile warning:
drivers/spi/fsl_qspi.c: In function 'fsl_qspi_probe':
drivers/spi/fsl_qspi.c:937:15:
  warning: cast to pointer from integer of different size
					 [-Wint-to-pointer-cast]
  priv->regs = (struct fsl_qspi_regs *)plat->reg_base;
               ^
Just make the cast explicit.

Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:27:49 -08:00
Simon Glass
f2b85ab5e6 dm: x86: spi: Convert ICH SPI driver to driver model PCI API
At present this SPI driver works by searching the PCI buses for its
peripheral. It also uses the legacy PCI API.

In addition the driver has code to determine the type of Intel PCH that is
used (version 7 or version 9). Now that we have proper PCH drivers we can
use those to obtain the information we need.

While the device tree has a node for the SPI peripheral it is not in the
right place. It should be on the PCI bus as a sub-peripheral of the LPC
device.

Update the device tree files to show the SPI controller within the PCH, so
that PCI access works as expected.

This patch includes Bin's fix-up patch from here:

   https://patchwork.ozlabs.org/patch/569478/

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-24 12:07:17 +08:00
Simon Glass
fffe25db04 spi: ich: Separate out the read/write trace from normal debugging
The trace is seldom useful for basic debugging. Allow it to be enabled
separately so that it is easier to see the more important init and error
debug messages.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-24 12:07:17 +08:00
Simon Glass
90a28470fc rockchip: spi: Remove the explicit pinctrl setting
The correct pinctrl is handled automatically so we don't need to do it in
the driver. The exception is when we want to use a different chip select
(other than 0). But this isn't used at present.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:36 -07:00
Simon Glass
e15af8e2cd rockchip: spi: Correct chip-enable code
At present there is an incorrect call to rkspi_enable_chip(). It should
be disabling the chip, not enabling it. Correct this and ensure that the
chip is disabled when releasing the bus.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:36 -07:00
Simon Glass
183a3a0f67 rockchip: spi: Implement the delays
Some devices need delays before and after activiation. Implement these
features in the SPI driver so that we will be able to enable the Chrome
OS EC.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:36 -07:00
Simon Glass
2b9fe111ec rockchip: spi: Correct the bus init code
Two of the init values are created locally so cannot be out of range.
The masking is unnecessary and in one case is incorrect. Fix it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:35 -07:00
Simon Glass
28a943c110 rockchip: spi: Remember the last speed to avoid re-setting it
Rather than changing the clock to the same value on every transaction,
remember the last value and don't adjust the clock unless it is necessary.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:35 -07:00
Simon Glass
6d97786b4c rockchip: spi: Avoid setting the pinctrl twice
If full pinctrl is enabled we don't need to manually set the pinctrl in the
driver. It will happen automatically. Adjust the code to suit - we will
still use manual mode in SPL.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:34 -07:00
Simon Glass
71037d1ca0 rockchip: spi: Update the driver to use the new clock ID
We can use the new clk_get_by_index() function to get the correct clock.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:34 -07:00
Vignesh R
74d49bfde3 spi: ti_qspi: Use 4-byte opcode for mmap read
ti-qspi driver currently uses 3-byte addressing mode(and opcodes) for
memory-mapped read. This restricts maximum addressable flash size to
16MB.
Enable the 4-byte addressing(and use 4-byte opcode) for memory-mapped
read to allow access to addresses above 16MB.

Signed-off-by: Ravi Babu <ravibabu@ti.com>
[vigneshr@ti.com: Re-word commit description]
Signed-off-by: Vignesh R <vigneshr@ti.com>
2016-01-20 10:19:33 -05:00
Tom Rini
22bd03a6a2 spi: rk_spi: Fix debug format warning
We need to use %lx not %x to describe a fdt_addr_t

Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-01-19 08:31:46 -05:00
Tom Rini
5b8031ccb4 Add more SPDX-License-Identifier tags
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously.  Convert all of these to the correct SPDX-License-Identifier
tag.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-01-19 08:31:21 -05:00
Stefan Roese
9985bdb1ce spi: kirkwood_spi.c: Add driver model support
This patch adds driver model support to the kirkwood SPI driver. Which
is also used on the MVEBU SoC's, now being converted to DM. Non-DM
support is still available for the "older" platforms using this
driver, like kirkwood.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jagan Teki <jteki@openedev.com>
Cc: Simon Glass <sjg@chromium.org>
2016-01-14 14:08:59 +01:00
Stefan Roese
18dd3b2221 spi: kirkwood_spi.c: Prepare for driver model support
This patch prepares the Kirkwood SPI driver, also used on the MVEBU board
(Armada XP / 38x), for the conversion to driver model.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jagan Teki <jteki@openedev.com>
Cc: Simon Glass <sjg@chromium.org>
2016-01-14 14:08:59 +01:00
Mugunthan V N
106f813907 drivers: spi: ti_qspi: convert driver to adopt device driver model
adopt ti_qspi driver to device driver model

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-01-13 18:47:27 +05:30
Mugunthan V N
f8e2f92d41 spi: Add support for dual and quad mode
spi bus can support dual and quad wire data transfers for tx and
rx. So defining dual and quad modes for both tx and rx. Also add
support to parse bus width used for spi tx and rx transfers.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13 18:47:27 +05:30
Mugunthan V N
223091443c drivers: spi: ti_qspi: prepare driver for DM conversion
Prepare driver for DM conversion.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-01-13 18:47:27 +05:30
Mugunthan V N
9c42558afb drivers: spi:ti_qspi: change ti_qspi_slave to ti_qspi_priv for driver model conversion
Changing the ti_qspi_priv structure and its instance names from
to priv for driver mode conversion.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-01-13 18:47:27 +05:30
Mugunthan V N
ec712f490d drivers: spi: ti_qspi: do not hard code chip select for memory map configuration
To enable memory map in dra7xx, specific chip select must be
written to control module register. But this hard coded to chip
select 1, fixing it by writing the specific chip select value to
control module register.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-01-13 18:47:27 +05:30
Jagan Teki
91292e0bee spi: Rename op_mode_rx to mode_rx
Since spi rx mode macro's are renamed to simple and
meaninfull, this patch will rename the respective
structure members.

Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13 18:47:26 +05:30
Jagan Teki
e5961f0706 spi: Rename SPI_OPM_RX_* to SPI_RX_*
SPI_OPM_RX_AS 	- SPI_RX_SLOW
SPI_OPM_RX_AF	- SPI_RX_FAST
SPI_OPM_RX_DOUT	- SPI_RX_DUAL
SPI_OPM_RX_QOF	- SPI_RX_QUAD

Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13 18:47:26 +05:30
Jagan Teki
cdf3393814 spi: Rename SPI_TX_BP|QPP to SPI_TX_BYTE|QUAD
Since SPI_TX_* are spi_slave{} members so use spi protocol
notation instead spi flash programming, like

SPI_TX_BP  => SPI_TX_BYTE
SPI_TX_QPP => SPI_TX_QUAD

Cc: Simon Glass <sjg@chromium.org>
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13 18:47:25 +05:30
Jagan Teki
095a41d3c2 spi: Use mode instead of op_mode_tx
Used mode member from spi_slave{} instead of op_mode_tx.

Cc: Simon Glass <sjg@chromium.org>
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13 18:47:25 +05:30
Gong Qianyu
8770413f38 spi: fsl_qspi: fix an error of using GENMASK
This commit fixes the change of below commit
"spi: fsl_qspi: Use GENMASK"
(sha1 :bad490a24212c068c5b718b9189f47ea4075d078)

Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-01-07 20:29:33 +05:30
Nathan Rossi
04a44d3671 spi: zynq_qspi: Add configuration to disable LQSPI feature
When the Zynq Boot ROM code loads the payload from QSPI it uses the
LQSPI feature of the QSPI device, however it does not clean up its
configuration before handing over to the payload which leaves the device
confgured to by-pass the standard non-linear operating mode.

This ensures the Linear QSPI mode is disabled before re-enabling the
device.

Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Cc: Jagan Teki <jteki@openedev.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-12-18 13:15:57 +01:00
Alexander Stein
beedbc2ea0 fsl_qspi: Pet the watchdog while reading/writing
When reading a large blob. e.g. a linux kernel (several MiBs) a watchdog
timeout might occur meanwhile. So pet the watchdog while operating on
the flash.

Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-15 08:57:33 +08:00
Michal Simek
76de51a6da spi: xilinx: Add new compatible strings
Add xlnx,xps-spi-2.00.a/b which is compatible string
listed in the Linux kernel.
Remove origin one which has no real background.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-12-11 22:12:24 +05:30
Michal Simek
8e4920e53e spi: Kconfig: Fix correct target name for ZynqMP
ZynqMP is using different symbol.
Use correct one.

Reviewed-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-12-11 22:12:23 +05:30
Michal Simek
23ef5aea84 spi: zynq_spi: Add cadence compatible string
Extend compatible list table for cdns,spi-r1p6 compatible string.

Reviewed-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-12-11 22:12:23 +05:30
Jagan Teki
cd337da21e spi: ti_qspi: Fix SPI_3WIRE checking using mode
SPI_3WIRE is spi mode not spi flags, so this patch fixed
the spi-3wire checking throgh mode instead of flags.

Cc: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-12-11 22:12:23 +05:30
Jagan Teki
379b49d82e spi: Get spi-3wire from dts
spi-3wire is used when SI/SO signals shared so get
the same from dts node and assign to mode on slave
plat->mode.

Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-12-11 22:12:23 +05:30
Simon Glass
24b852a7a2 Move console definitions into a new console.h file
The console includes a global variable and several functions that are only
used by a small subset of U-Boot files. Before adding more functions, move
the definitions into their own header file.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-11-19 20:27:50 -07:00
Tom Rini
9ef671c9d4 Merge branch 'master' of git://git.denx.de/u-boot-spi 2015-11-19 13:27:26 -05:00
Michal Simek
281f1566b8 dm: spi: Add support for all targets which requires MANUAL_RELOC
It is follow up patch based on
"dm: Add support for all targets which requires MANUAL_RELOC"
(sha1: 484fdf5ba0)
to update function pointers for DM.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-11-19 13:10:16 +01:00
Thomas Chou
7313e21a1e altera_spi: change ioremap to map_physmem
Change ioremap() to map_physmem(), as it is more used in u-boot.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
2015-11-18 21:18:30 +08:00
Vignesh R
857db48e5f spi: ti_qspi: Add dummy readl for bus sync
Add dummy readl after invalidating cmd field of QSPI_CMD_REG to ensure
bus sync. Without this device's CS is not deactivated reliably leading
to failure to enumerate flash or failure to set quad enable bit on
Macronix flash present on am437x-sk and am437x-idk evms.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-11-17 23:43:29 +05:30
Tom Warren
4e675ff244 Tegra: T210: Add QSPI driver
This is the normal Tegra SPI driver modified to work with the
QSPI controller in Tegra210. It does not do 2x/4x transfers
or any other QSPI protocol.

Signed-off-by: Yen Lin <yelin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-11-12 09:21:07 -07:00
Thomas Chou
ddf34c2606 spi: altera_spi: minor clean up
- Remove the penultimate comma in of_match ids

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-11-06 09:14:12 +08:00
Chin Liang See
4e609b6cb1 spi: cadence_qspi: Ensure check for max frequency in place
Ensure the intended SCLK frequency not exceeding the maximum
frequency. If that happen, SCLK will set to maximum frequency.

Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vikas Manocha <vikas.manocha@st.com>
Cc: Jagannadh Teki <jteki@openedev.com>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
2015-11-05 02:34:15 +01:00
Chin Liang See
040f4ba742 spi: cadence_qspi: Fix fdt read of spi-max-frequency
Fix the fdt read for spi-max-frequency as it's contained
in the child node. Current state of code is always
returning default value.

Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vikas Manocha <vikas.manocha@st.com>
Cc: Jagannadh Teki <jteki@openedev.com>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
2015-11-05 02:34:15 +01:00
Chin Liang See
98fbd71d7a spi: cadence_qspi: Ensure spi_calibration is run when sclk change
Ensuring spi_calibration is run when there is a change of sclk
frequency. This will ensure the qspi flash access works for high
sclk frequency

Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vikas Manocha <vikas.manocha@st.com>
Cc: Jagannadh Teki <jteki@openedev.com>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-11-05 02:34:15 +01:00
Tom Rini
446d37c1ac Merge branch 'master' of git://git.denx.de/u-boot-spi 2015-10-28 16:56:43 -04:00
Jagan Teki
bef87adf95 spi: altera_spi: Minor cleanup
- Moved macro definitions to top
- Give tab space to CONFIG_ALTERA_SPI_IDLE_VAL value
- Re-arrange header includes ascending order

Acked-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-28 13:54:09 +05:30
Jagan Teki
9c63d44e92 spi: altera_spi: Use BIT macro
Replace numerical bit shift with BIT macro
in altera_spi

:%s/(1 << nr)/BIT(nr)/g
where nr = 0, 1, 2 .... 31

Cc: Marek Vasut <marex@denx.de>
Acked-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-28 13:53:58 +05:30
Tom Rini
2431492aef Merge git://git.denx.de/u-boot-dm 2015-10-27 19:08:19 -04:00
Jagan Teki
d2436301c5 spi: xilinx_spi: Use GENMASK
Replace numeric mask hexcodes with GENMASK macro
in xilinx_spi

Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-27 23:21:43 +05:30
Jagan Teki
76538ec648 spi: tegra: Use GENMASK
Replace numeric mask hexcodes with GENMASK macro
in tegra*.c

Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-27 23:21:43 +05:30
Jagan Teki
0ebc0ec620 spi: omap3_spi: Use GENMASK
Replace numeric mask hexcodes with GENMASK macro
in omap3_spi

Cc: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-27 23:21:43 +05:30
Jagan Teki
bad490a242 spi: fsl_qspi: Use GENMASK
Replace numeric mask hexcodes with GENMASK macro
in fsl_qspi

Cc: York Sun <yorksun@freescale.com>
Cc: Haikun Wang <Haikun.Wang@freescale.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-27 23:21:43 +05:30
Jagan Teki
95e77d904e spi: designware_spi: Use GENMASK
Replace numeric mask hexcodes with GENMASK macro
in designware_spi

Cc: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-27 23:21:43 +05:30
Jagan Teki
a9d3b78023 spi: atmel_spi: Use GENMASK
Replace numeric mask hexcodes with GENMASK macro
in atmel_spi

Cc: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-27 23:21:42 +05:30
Jagan Teki
5ea392d43b spi: xilinx_spi: Use BIT macro
Replace numerical bit shift with BIT macro
in xilinx_spi

:%s/(1 << nr)/BIT(nr)/g
where nr = 0, 1, 2 .... 31

Cc: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-27 23:21:42 +05:30
Jagan Teki
847720c4e1 spi: ti_qspi: Use BIT macro
Replace numerical bit shift with BIT macro
in ti_qspi

:%s/(1 << nr)/BIT(nr)/g
where nr = 0, 1, 2 .... 31

Reviewed-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-27 23:21:33 +05:30
Jagan Teki
f692248f90 spi: tegra: Use BIT macro
Replace numerical bit shift with BIT macro
in tegra*.c

:%s/(1 << nr)/BIT(nr)/g
where nr = 0, 1, 2 .... 31

Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Tom Warren <twarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-27 23:21:28 +05:30
Jagan Teki
ccaa948501 spi: sh_qspi: Use BIT macro
Replace numerical bit shift with BIT macro
in sh_qspi

:%s/(1 << nr)/BIT(nr)/g
where nr = 0, 1, 2 .... 31

Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-27 23:21:28 +05:30
Jagan Teki
3e1b4dcf1c spi: omap3_spi: Use BIT macro
Replace numerical bit shift with BIT macro
in omap3_spi

:%s/(1 << nr)/BIT(nr)/g
where nr = 0, 1, 2 .... 31

Cc: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-27 23:21:28 +05:30
Jagan Teki
a048d4bbb1 spi: mpc8xxx_spi: Use BIT macro
Replace numerical bit shift with BIT macro
in mpc8xxx_spi

:%s/(1 << nr)/BIT(nr)/g
where nr = 0, 1, 2 .... 31

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-27 23:21:28 +05:30
Jagan Teki
69fd4c386c spi: ich: Use BIT macro
Replace numerical bit shift with BIT macro
in ich

:%s/(1 << nr)/BIT(nr)/g
where nr = 0, 1, 2 .... 31

Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-27 23:21:16 +05:30
Jagan Teki
29e6abd94b spi: fsl: Use BIT macro
Replace numerical bit shift with BIT macro
in fsl_*spi.c

:%s/(1 << nr)/BIT(nr)/g
where nr = 0, 1, 2 .... 31

Cc: York Sun <yorksun@freescale.com>
Cc: Haikun Wang <Haikun.Wang@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-27 23:19:29 +05:30
Jagan Teki
431a9f0286 spi: designware_spi: Use BIT macro
Replace numerical bit shift with BIT macro
in designware_spi

:%s/(1 << nr)/BIT(nr)/g
where nr = 0, 1, 2 .... 31

Cc: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-27 23:19:29 +05:30
Jagan Teki
b7e83b087c spi: cadence_qspi_apb: Use BIT macro
Replace numerical bit shift with BIT macro
in cadence_qspi_apb

:%s/(1 << nr)/BIT(nr)/g
where nr = 0, 1, 2 .... 31

Cc: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-27 23:19:29 +05:30
Jagan Teki
c0d1ea4acd spi: bfin_spi6xx: Use BIT macro
Replace numerical bit shift with BIT macro
in bfin_spi6xx

:%s/(1 << nr)/BIT(nr)/g
where nr = 0, 1, 2 .... 31

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-27 23:19:29 +05:30
Jagan Teki
a48c4eb6a7 spi: atmel_spi: Use BIT macro
Replace numerical bit shift with BIT macro
in atmel_spi

:%s/(1 << nr)/BIT(nr)/g
where nr = 0, 1, 2 .... 31

Cc: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-27 23:19:29 +05:30
Jagan Teki
9cf2ffb3c3 spi: zynq_[q]spi: Use GENMASK macro
GENMASK macro used on zynq_spi.c and zynq_qspi.c

GENMASK is used to create a contiguous bitmask([hi:lo]).
Ex: (0x7 << 3) => GENMASK(5, 3)

Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-27 23:19:15 +05:30
Jagan Teki
736b4df15d spi: zynq_[q]spi: Use BIT macro
Used BIT macro on zynq_spi.c and zynq_qspi.c

:%s/(1 << nr)/BIT(nr)/g
where nr = 0, 1, 2 .... 31

Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-27 23:18:48 +05:30
Jagan Teki
e5e0d68f27 spi: zynq_qspi: Minor cleanups
- Use __func__ on debug
- Removed unnecessary comment
- Fix function name in debug as zynq_qspi_xfer instead of spi_xfer

Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-25 20:17:03 +05:30
Jagan Teki
86e99b9861 spi: zynq_spi: Remove unneeded headers
- Removed unneeded inclusion of header files
- Add "Xilinx" on license text

Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-25 20:17:03 +05:30
Jagan Teki
2775e91835 spi: zynq_qspi: Fix to configure CPOL, CPHA mask
priv->mode is initialized when .set_speed triggers
with mode value, so checking mode for configuring
CPOL, CPHA using priv->mode is invalid hence use
mode from .set_speed argument, and at the end
priv->mode will initialized with mode.

This patch also replaces formatting string to use
speed instead of mode in .set_speed ops.

Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-25 20:17:03 +05:30
Jagan Teki
191269987c spi: zynq_spi: Store cs value into private data
Store cs value into private data and use it while activating
chipselect instead of passing through function.

Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-25 20:17:02 +05:30
Jagan Teki
dda6241a1d spi: zynq_spi: Rename baudrate divisor mask name
Rename ZYNQ_SPI_CR_BRD_MASK to ZYNQ_SPI_CR_BAUD_MASK
for more readable.

Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-25 20:17:02 +05:30
Jagan Teki
46ab8a6a13 spi: zynq_spi: Add config reg shift named macros
Update the numerical values for baudrate and chipselect
with config reg shift named macro's

Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-25 20:17:02 +05:30
Jagan Teki
78a025ace8 spi: Kconfig: Add Zynq QSPI controller entry
Add Zynq QSPI controller Kconfig entry.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
2015-10-25 20:17:02 +05:30
Jagan Teki
46d0a9913c spi: Add zynq qspi controller driver
Added zynq qspi controller driver for Xilinx Zynq APSOC,
this driver is driver-model driven with devicetree support.

=> sf probe
SF: Detected S25FL128S_64K with page size 256 Bytes, erase size 64 KiB, total 16 MiB
=> mw.b 0x100 0xCC 0x1000000
=> sf update 0x100 0x0 0x1000000
device 0 whole chip
16777216 bytes written, 0 bytes skipped in 59.842s, speed 289262 B/s
=> sf read 0x3000000 0x0 0x1000000
device 0 whole chip
SF: 16777216 bytes @ 0x0 Read: OK
=> cmp.b 0x3000000 0x100 0x1000000
Total of 16777216 byte(s) were the same

Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Jagan Teki <jteki@openedev.com>
2015-10-25 20:17:01 +05:30
Simon Glass
bcbe3d1579 dm: Rename dev_get_parentdata() to dev_get_parent_priv()
The current name is inconsistent with other driver model data access
functions. Rename it and fix up all users.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
2015-10-23 09:42:28 -06:00
Thomas Chou
15a56f9cb7 spi : convert altera_spi to driver model
Convert altera_spi to driver model

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-10-23 07:36:56 +08:00
George McCollister
5ac98cb9bd x86: spi: Add support for Wildcat Point
Add the Wildcat Point ID so Broadwell U based boards can use SPI.

Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-10-21 07:46:27 -06:00
Mirza Krak
5cb1b7b395 spi: tegra20: Add support for mode selection
Respect the mode passed in set_mode ops.

Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-10-11 16:43:06 +05:30
Jagan Teki
a22bba81e4 spi: zynq_spi: Fix to configure CPOL, CPHA mask
priv->mode is initialized when .set_speed triggers
with mode value, so checking mode for configuring
CPOL, CPHA using priv->mode is invalid hence use
mode from .set_speed argument, and at the end
priv->mode will initialized with mode.

This patch also replaces formatting string to use
speed instead of mode in .set_speed ops.

Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-11 16:43:06 +05:30
Jagan Teki
d5f60737db spi: xilinx_spi: Fix to configure CPOL, CPHA mask
priv->mode is initialized when .set_speed triggers
with mode value, so checking mode for configuring
CPOL, CPHA using priv->mode is invalid hence use
mode from .set_speed argument, and at the end
priv->mode will initialized with mode.

This patch also replaces formatting string to use
speed instead of mode in .set_speed ops.

Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-11 16:43:06 +05:30
Heiko Schocher
92a3188d7d bitops: introduce BIT() definition
introduce BIT() definition, used in at91_udc gadget
driver.

Signed-off-by: Heiko Schocher <hs@denx.de>
[remove all other occurrences of BIT(x) definition]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
2015-09-11 17:15:32 -04:00
Simon Glass
cf92e05c01 Move ALLOC_CACHE_ALIGN_BUFFER() to the new memalign.h header
Now that we have a new header file for cache-aligned allocation, we should
move the stack-based allocation macro there also.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-09-11 17:15:20 -04:00
Simon Glass
1b2fd5bf4e rockchip: Add SPI driver
Add a SPI driver for the Rockchip RK3288, using driver model. It should work
for other Rockchip SoCs also.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-09-02 21:28:24 -06:00
Simon Glass
4e9838c102 dm: Use dev_get_addr() where possible
This is a convenient way for a driver to get the hardware address of a
device, when regmap or syscon are not being used. Change existing callers
to use it as an example to others.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
2015-08-31 07:57:26 -06:00
Tom Rini
952bd79b53 Merge branch 'master' of git://git.denx.de/u-boot-spi 2015-08-18 08:25:24 -04:00
Vignesh R
8ddd9c485f spi: ti_qspi: Use DMA to read from qspi flash
ti_qspi uses memory map mode for faster read. Enabling DMA will increase
read speed by 3x @48MHz on DRA74 EVM.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-08-17 23:29:15 +05:30
vishalm@ti.com
a39cfe717c ti: qspi: set flash quad bit based on quad support flag
Update op_mode_rx flag based on CONFIG_QSPI_QUAD_SUPPORT flag,
instead of platform.

Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-08-17 23:29:14 +05:30
Thomas Abraham
77b55e8cfc ARM: exynos: move SoC sources to mach-exynos
Move arch/arm/cpu/armv7/exynos/* to arch/arm/mach-exynos/* to allow
reuse of existing code for ARMv8 based Exynos platforms.

Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-08-17 13:06:52 +09:00
Nikita Kiryanov
2ff97625cb spi: omap3_spi: add am43xx support to omap3_spi
Add support for AM43XX to the omap3_spi driver.

Cc: Jagan Teki <jteki@openedev.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-08-12 20:48:02 -04:00
York Sun
fdb9f349be lib/fdtdec: Fix compiling warning caused by changing fdt_addr_t type
fdt_addr_t is changed to phys_addr_t. The format in debug should be updated
to %pa to match the type.

Signed-off-by: York Sun <yorksun@freescale.com>
CC: Simon Glass <sjg@chromium.org>
2015-08-06 07:31:13 -06:00
Simon Glass
c7d50e7fb9 exynos: spi: Convert the timeout to debug()
Since the timeout is reported through normal channels, and is sometimes
expected (e.g. if the bus is being probed for a non-existent device),
don't display the message in the driver.

In general, drivers should not write to the console as this limits their
usefulness in error conditions.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-08-05 21:06:14 -06:00
Michal Simek
80fd9792f5 spi: zynq_spi: Simplify debug macro
Trivial fix.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-07-28 11:56:28 +02:00
Michal Simek
40b383fa84 spi: Fix zynq SPI binding
Zynq is using Cadence IP where binding is documented in the Linux kernel
and there is no reason to use different binding.
Synchronize it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-07-28 11:56:22 +02:00
Simon Glass
6f849c3012 dm: spi: Make local functions static
Several functions in this file should be marked as static. Update them.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-07-21 17:39:27 -06:00
Haikun Wang
b1d9e46a0b fdt: armv8: Fix build warnings on armv8
Fix below build warnings on armv8,
drivers/spi/fsl_dspi.c: In function ‘fsl_dspi_ofdata_to_platdata’:
drivers/spi/fsl_dspi.c:667:2:
warning: format ‘%x’ expects argument of type ‘unsigned int’,
	but argument 2 has type ‘fdt_addr_t’ [-Wformat=]
debug("DSPI: regs=0x%x, max-frequency=%d, endianess=%s, num-cs=%d\n",
		    ^
lib/fdtdec.c: In function ‘fdtdec_get_addr_size’:
lib/fdtdec.c:105:4:
warning: format ‘%lx’ expects argument of type ‘long unsigned int’,
but argument 3 has type ‘fdt_size_t’ [-Wformat=]
debug("addr=%08lx, size=%08lx\n",
			    ^

Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-07-20 07:21:47 -06:00
Tom Rini
605e15db2b Merge git://git.denx.de/u-boot-x86 2015-07-15 10:41:20 -04:00
Simon Glass
5078792807 dm: spi: Correct BIOS protection logic for ICH9
The logic is incorrect and currently has no effect. Fix it so that we can
write to SPI flash, since by default it is write-protected.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Andrew Bradford <andrew.bradford@kodakalaris.com>
2015-07-14 18:03:19 -06:00
Simon Glass
e1e332c8f2 dm: spi: Correct status register access width
The status register on ICH9 is a single byte, so use byte access when
writing to it, to avoid updating the control register also.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-07-14 18:03:19 -06:00
Simon Glass
5d4a757ca5 dm: spi: Correct minor nits in ICH driver
Tidy up three minor problems in this file.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-07-14 18:03:15 -06:00
Vikas Manocha
70bb2b1415 spi: cadence_qspi: support FIFO width other than 4 bytes
This patch makes the code compatible with FIFO depths other than 4
bytes. It also simplify read/write FIFO loops.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
2015-07-03 13:50:53 +05:30
Vikas Manocha
90a2f71711 spi: cadence_qspi: get sram size from device tree
sram size could be different on different socs, e.g. on stv0991 it is 256 while
on altera platform it is 128. It is better to receive it from device tree.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
2015-07-03 13:50:53 +05:30
Vikas Manocha
c0535c0ef0 spi: cadence_qspi: move the sram partition in init
There is no need to re-configure sram partition for every read/write for
better full use of sram for read or write. This patch divides the half
sram for read & half for write once at initialization.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
2015-07-03 13:50:53 +05:30
Angelo Dureghello
8aa5f1d971 spi: cf_qspi: fix clamp macro type check compilation warnings
Fix compilation warnings for redefined 'clamp' macro and non-uniform
clamp macro types.

Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
2015-07-01 22:58:50 +05:30
Jagan Teki
4495830c58 spi: Kconfig: Add TEGRA20_SLINK entry
Added TEGRA20_SLINK entry on Kconfig with help description.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
2015-07-01 21:39:05 +05:30
Jagan Teki
2f3e6f8cc1 spi: Kconfig: Add TEGRA20_SFLASH entry
Added TEGRA20_SFLASH entry on Kconfig with help description.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
2015-07-01 21:39:05 +05:30
Jagan Teki
5bf9a2d3dd spi: Kconfig: Add TEGRA114_SPI entry
Added TEGRA114_SPI entry on Kconfig with help description.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
2015-07-01 21:39:05 +05:30
Jagan Teki
456360102c spi: Kconfig: Add ICH_SPI entry
Added ICH_SPI entry on Kconfig with help description.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-07-01 21:39:05 +05:30
Jagan Teki
c354eee8d0 spi: Kconfig: Add EXYNOS_SPI entry
Added EXYNOS_SPI entry on Kconfig with help description.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-07-01 21:39:05 +05:30
Jagan Teki
91c22d046c spi: Kconfig: Add FSL_QSPI entry
Added FSL_QSPI entry on Kconfig with help description.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Peng Fan <Peng.Fan@freescale.com>
Cc: Haikun Wang <haikun.wang@freescale.com>
2015-07-01 21:39:04 +05:30
Jagan Teki
3debffa704 spi: Kconfig: Add FSL_ESPI entry
Added FSL_ESPI entry on Kconfig with help description.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Haikun Wang <haikun.wang@freescale.com>
2015-07-01 21:39:04 +05:30
Jagan Teki
94ea308d75 spi: Kconfig: Add FSL_DSPI entry
Added FSL_DSPI entry on Kconfig with help description.

Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Haikun Wang <haikun.wang@freescale.com>
2015-07-01 21:39:04 +05:30