This converts the following to Kconfig:
CONFIG_SPL_RELOC_TEXT_BASE
CONFIG_SPL_RELOC_STACK
CONFIG_SPL_RELOC_MALLOC_ADDR
CONFIG_SPL_RELOC_MALLOC_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
Update the Kconfig entry to have the correct defaults for i.MX7
platforms, and move the existing large comment from imx7_spl.h to
doc/imx/common/imx7.txt so that it's not lost.
Signed-off-by: Tom Rini <trini@konsulko.com>
Update the Kconfig entry to have the correct defaults for i.MX6
platforms, and move the existing large comment from imx6_spl.h to
doc/imx/common/imx6.txt so that it's not lost.
Signed-off-by: Tom Rini <trini@konsulko.com>
A number of PowerPC platforms define this, for SPL. To move this to
Kconfig, it needs to be CONFIG_SPL_SYS_CCSR_DO_NOT_RELOCATE, so use
CONFIG_IS_ENABLED() to check for usage. A number of layerscape
platforms bring this logic from PowerPC, but only need a small part of
it, for the fman driver. Remove their unused portion at least.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_BSS_MAX_SIZE
CONFIG_SPL_MAX_FOOTPRINT
Note that the da850evm platforms were violating the "only use one" rule
here, and so now hard-code their BSS limit.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_PAD_TO
CONFIG_SPL_MAX_SIZE
CONFIG_TPL_PAD_TO
CONFIG_TPL_MAX_SIZE
Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the
existing places.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_FS_LOAD_ARGS_NAME
CONFIG_SPL_FS_LOAD_KERNEL_NAME
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_INIT_MINIMAL
CONFIG_SPL_FLUSH_IMAGE
CONFIG_SPL_SKIP_RELOCATE
Signed-off-by: Tom Rini <trini@konsulko.com>
This is only referenced in non-SPL_DM cases, of which there are
currently none. Remove this option and slightly re-organize the code is
there is now never an if/else at the start of spl_sata_load_image()
Signed-off-by: Tom Rini <trini@konsulko.com>
If the fitImage has some bad block in fit image area, the
offset must be recalulcated. This should be done always.
After implementing it in mxs now is possible to call the function
even for that platform.
Cc: Fabio Estevam <festevam@gmail.com>
Tested-By: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Booting of non-FIT images bypass our chain-of-trust boot flow,
these options should not be allowed when high security is set.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This matches what this support is called in the non-SPL case. The postfix
_SUPPORT is redundant as enabling Kconfig options implies support.
With this we can use CONFIG_IS_ENABLED() as needed.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for VPL, a new phase of U-Boot. This runs after TPL. It is
responsible for selecting which SPL binary to run, based on a
verified-boot process.
Signed-off-by: Simon Glass <sjg@chromium.org>
This was implemented in order to get dual-slot bootloader
partitions on the BeagleBone Black, whose MLO boots from
the first bootable partition: MLO chainloads u-boot in the
same way.
Signed-off-by: Jérôme Carretero <cJ-uboot@zougloub.eu>
Reviewed-by: Tom Rini <trini@konsulko.com>
Use the CONFIG macros to conditionally build the GPIO hogging support in
either the SPL or U-Boot, or both, depending on the configuration. Also
call the GPIO hog probe function in the common SPL board initialization
as an equivalent to adding it to the U-Boot init sequence functions.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A big part is the DM pinctrl driver, which allows us to get rid of quite
some custom pinmux code and make the whole port much more robust. Many
thanks to Samuel for that nice contribution! There are some more or less
cosmetic warnings about missing clocks right now, I will send the trivial
fixes for that later.
Another big chunk is the mkimage upgrade, which adds RISC-V and TOC0
(secure images) support. Both features are unused at the moment, but I
have an always-secure board that will use that once the DT lands in the
kernel.
On top of those big things we have some smaller fixes, improving the
I2C DM support, fixing some H6/H616 early clock setup and improving the
eMMC boot partition support.
The gitlab CI completed successfully, including the build test for all
161 sunxi boards. I also boot tested on a A64, A20, H3, H6, and F1C100
board. USB, SD card, eMMC, and Ethernet all work there (where applicable).
Platforms can overwrite the weak definition of spl_mmc_boot_mode() to
determine where to load U-Boot proper from.
For most of them this is a trivial decision based on Kconfig variables,
but it might be desirable the probe the actual device to answer this
question.
Pass the pointer to the mmc struct to that function, so implementations
can make use of that.
Compile-tested for all users changed.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Ley Foon Tan <ley.foon.tan@inte.com> (for SoCFPGA)
Acked-by: Lokesh Vutla <lokeshvutla@ti.com> (for OMAP and K3)
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a boot method for loading the next stage from the host. It is
mostly modeled off of spl_load_image_ext. I am not really sure why/how
spl_load_image_fat uses three different methods to load the image, but
the simple case seems to work OK for now.
To control the presence of this boot method, we add a config symbol.
While we're at it, we update the original semihosting config symbol.
I think semihosting has some advantages of other forms of JTAG boot.
Common other ways to boot from JTAG include:
- Implementing DDR initialization through JTAG (typically with dozens of
lines of TCL) and then loading U-Boot. The DDR initialization
typically uses hard-coded register writes, and is not easily adapted
to different boards. BOOT_DEVICE_SMH allows booting with SPL,
leveraging U-Boot's existing DDR initialization code. This is the
method used by NXP's CodeWarrior IDE on Layerscape processors (see
AN12270).
- Loading a bootloader into SDRAM, waiting for it to initialize DDR, and
then loading U-Boot. This is tricky, because the debugger must stop the
boot after the bootloader has completed its work. Trying to load
U-Boot too early can cause failure to boot. This is the method used by
Xilinx with its Zynq(MP) processors.
- Loading SPL with BOOT_DEVICE_RAM and breaking before SPL loads the
image to load U-Boot at the appropriate place. This can be a bit
tricky, because the load address is dependent on the header size. An
elf with symbols must also be used in order to stop at the appropriate
point. BOOT_DEVICE_SMH can be viewed as an extension of this process,
where SPL automatically stops and tells the host where to place the
image.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Add the support of image pre load in spl or tpl
when loading an image from ram.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Fix the help which should refer to TPL, not SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Suggested-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
When CONFIG_SPL_FIT is enabled we do not access U-Boot directly in
the image, since it is embedded in a FIT which is parsed at runtime.
Provide a CONFIG option to drop the symbols in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
These symbols are incorrect, meaning that binman cannot find the
associated entry. This leads to errors like:
binman: Section '/binman/simple-bin': Symbol '_binman_spl_prop_size'
in entry '/binman/simple-bin/u-boot-spl/u-boot-spl-nodtb':
Entry 'spl' not found in list (mkimage,u-boot-spl-nodtb,
u-boot-spl-bss-pad,u-boot-spl-dtb,u-boot-spl,u-boot-img,main-section)
Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
ymodem_read_fit() driver will end copying up to BUF_SIZE boundary even
when requested size of copy operation is less than that.
For example, if offset = 0, size = 1440B, ymodem_read_fit() ends up
copying 2KB from offset = 0, to destination buffer addr
This causes data corruption when malloc'd buffer is passed during UART
boot since commit 03f1f78a9b ("spl: fit: Prefer a malloc()'d buffer
for loading images")
With this, UART boot works again on K3 (AM654, J7, AM64) family of
devices.
Fixes: 03f1f78a9b ("spl: fit: Prefer a malloc()'d buffer for loading images")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Currently the names MMC1, MMC2 and MMC2_2 are output in the SPL. To
achieve more userbility here the name of the boot source can be returned.
E.g. for "MMC1" -> "eMMC" or "MMC2" -> "SD card".
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
At present we rely on the key blob being in the global_data fdt_blob
pointer. This is true in U-Boot but not with tools. For clarity, pass the
parameter around.
Signed-off-by: Simon Glass <sjg@chromium.org>
Falcon mode is very useful in improving boot speed. A question that
Falcon mode asks is "Where do I look for the kernel". With MMC boot
media, the correct answer is CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR.
The scope of this patch is to move this to Kconfig.
It is possible for a system to support Falcon mode from NOR but not
MMC. In that case, mmc_load_image_raw_os() would not be used. To
address this, conditionally compile mmc_load_image_raw_os() when
SPL_FALCON_BOOT_MMCSD, instead of SPL_OS_BOOT.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Move spl_start_uboot to its own guard in spl_mmc.c, rerun migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
- fdt_support: Add fdt_for_each_node_by_compatible() helper macro
(Marek)
- turris_omnia: Fixup SATA or PCIe nodes at runtime in DT blob (Pali)
- pci_mvebu: Add support for Kirkwood PCIe controllers (Pali)
- SPL: More verifications for kwbimage in SPL (Pali)
- mvebu: Remove comphy_update_map() (Pali)
- Minor misc stuff
Commit 9baab60b80 ("SPL: Add support for parsing board / BootROM specific
image types") added support for loading board specific image types.
This commit adds support for a new weak function spl_parse_board_header()
which is called after loading boot image. Board may implement this function
for checking if loaded board specific image is valid.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add parameter spl_boot_device to spl_parse_board_header(), which allows
the implementations to see from which device we are booting and do
boot-device-specific checks of the image header.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Factor out armv7m fragment to spl_perform_fixups(), which is an arch/board
specific function designed for this purpose.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
When, for various reasons, a bad FIT image is used where a loadable
image is marked as 0 length, attempt is made for a 0 length allocation and
read of 0 byte read operation.
Instead provide warning in log and skip attempting to do such a load.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
When building a system that has both TPL and SPL_OS_BOOT, code which
tests for CONFIG_SPL_OS_BOOT will be built and enabled in TPL, which is
not correct. While there is no CONFIG_TPL_OS_BOOT symbol at this time
(and likely will not ever be) we can use CONFIG_IS_ENABLED(OS_BOOT) in
these common paths to ensure we only compile these parts in the SPL
case.
Signed-off-by: Tom Rini <trini@konsulko.com>
Allow usage of the bootstage facilities in SPL.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make sure to (if applicable) flush the D-cache, invalidate I-cache,
and disable MMU and caches before jumping to OPTEE.
This fixes the SDP->SPL->OPTEE boot flow on iMX6Q and most likely on
some other ARM SoCs.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Add a host Kconfig for CRC32. With this we can use CONFIG_IS_ENABLED(CRC32)
directly in the host build, so drop the unnecessary indirection.
Add a few more conditions to SPL_CRC32 to avoid build failures as well as
TPL_CRC32. Also update hash.c to make crc32 optional and to actually take
notice of SPL_CRC32.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
cherry-picked from NXP code:
719d665a87c6: ("MLK-20467 imx8m: Fix issue for booting signed image through uuu")
which fixes secure boot on imx8m based boards. Problem was
that FIT header and so IVT header too, was loaded to
memallocated address. So the ivt header address coded
in IVT itself does not fit with the real position.
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Tim Harvey <tharvey@gateworks.com>
add hook function spl_load_simple_fit_fix_load()
which is called after fit image header is loaded.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The configuration CONFIG_OPTEE is defined 2 times:
1- in lib/optee/Kconfig for support of OPTEE images loaded by bootm command
2- in drivers/tee/optee/Kconfig for support of OP-TEE driver.
It is abnormal to have the same CONFIG define for 2 purpose;
and it is difficult to managed correctly their dependencies.
Moreover CONFIG_SPL_OPTEE is defined in common/spl/Kconfig
to manage OPTEE image load in SPL.
This definition causes an issue with the macro CONFIG_IS_ENABLED(OPTEE)
to test the availability of the OP-TEE driver.
This patch cleans the configuration dependency with:
- CONFIG_OPTEE_IMAGE (renamed) => support of OP-TEE image in U-Boot
- CONFIG_SPL_OPTEE_IMAGE (renamed) => support of OP-TEE image in SPL
- CONFIG_OPTEE (same) => support of OP-TEE driver in U-Boot
- CONFIG_OPTEE_LIB (new) => support of OP-TEE library
After this patch, the macro have the correct behavior:
- CONFIG_IS_ENABLED(OPTEE_IMAGE) => Load of OP-TEE image is supported
- CONFIG_IS_ENABLED(OPTEE) => OP-TEE driver is supported
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The current API is outdated as it requires a devicetree pointer.
Move these functions to use the ofnode API and update this globally. Add
some tests while we are here.
Correct the call in exynos_dsim_config_parse_dt() which is obviously
wrong.
Signed-off-by: Simon Glass <sjg@chromium.org>
Header file version.h does not use anything from timestamp.h. Including of
timestamp.h has side effect which cause recompiling object file at every
make run because timestamp.h changes at every run.
So remove timestamp.h from version.h and include timestamp.h in files
which needs it.
This change reduce recompilation time of final U-Boot binary when U-Boot
source files were not changed as less source files needs to be recompiled.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add in lib/acpi/acpi_table.c and test/dm/acpi.c, rework a few others]
Signed-off-by: Tom Rini <trini@konsulko.com>
All of these configs exist. Stick to using CONFIG_[ST]PL_HASH, and drop all
references to CONFIG_[ST]PL_HASH_SUPPORT. This means we need for
CHAIN_OF_TRUST to select SPL_HASH now.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[trini: Add TPL case, fix CHAIN_OF_TRUST, other tweaks]
Signed-off-by: Tom Rini <trini@konsulko.com>
Originally CONFIG_FIT_SHAxxx enabled specific SHA algos for and only
for hash_calculate() in common/image-fit.c. However, since commit
14f061dcb1 ("image: Drop IMAGE_ENABLE_SHAxxx"),
the correct selector was changed to CONFIG_SHAxxx.
The extra "_FIT_" variants are neither used, nor needed. Remove them.
One defconfig disables FIT_SHA256, which is now changed to 'SHA256'.
CMD_MVEBU_BUBT needs to select select SHA256 to avoid undefined
references to "sha256_*()". bubt.c needs sha256, so this selection is
correct. It is not clear why this problem did not manifest before.
Note that SHA selection in SPL is broken for this exact reason. There
is no corresponding SPL_SHAxxx. Fixing this is is beyond the scope of
this change.
Also note that we make CONFIG_FIT now imply SHA256, to make up for
FIT_SHA256 previously being a default y option.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[trini: Add imply SHA256 to FIT]
Signed-off-by: Tom Rini <trini@konsulko.com>
The code under drivers/net is related to ethernet networking drivers, in
some fashion or another. Drop these from the top-level Makefile and
also move the phy rule into drivers/net/Makefile which is where it
belongs. Make the new rule for drivers/net check for the build-stage
relevant ETH symbol.
Fix up some Kconfig dependencies while we're here to mirror how the
Makefile logic now works.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Introduce ETH, Kconfig dependency changes, am43xx fix]
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the power/ rules into drivers/power to avoid clutter in the Makefile
and drivers/Makefile files.
We must select SPL_POWER if SPL_POWER_DOMAIN is used, since the two are
currently independent and boards do not necessarily enable SPL_POWER.
Add a TPL_POWER as well, as that is used by one board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Rename this option so that CONFIG_IS_ENABLED can be used with it.
Oddly there is already an SPL_CACHE option. Drop it in favour of this one.
Drop the special SPL Makefile rule which is now superfluous.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Fixup some incorrect renames]
Signed-off-by: Tom Rini <trini@konsulko.com>
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that proper load and execution addresses are set in v1 kwbimage we
can use it for loading and booting U-Boot proper.
Use the new spl_parse_board_header() function to implement parsing the
kwbimage v1 header. Use information from this header to locate offset and
size of the U-Boot proper binary, instead of using the legacy U-Boot
header which is prepended to the U-Boot proper binary stored at fixed
offset. This has the advantage that we do not need to relay on legacy
U-Boot header anymore and therefore U-Boot proper binary can be stored at
any offset, as is the case when loading & booting U-Boot proper by
BootROM. The CONFIG_SYS_U_BOOT_OFFS option is therefore not used by SPL
code anymore.
Also allow to compile U-Boot SPL without CONFIG_SPL_SPI_FLASH_SUPPORT,
CONFIG_SPL_MMC_SUPPORT or CONFIG_SPL_SATA_SUPPORT set. In this case
BootROM is used for loading and executing U-Boot proper. This reduces the
size of U-Boot's SPL image. By default these config options are enabled
and so BootROM loading is not used. In some cases BootROM reads from SPI
NOR at lower speed than U-Boot SPL. So people can decide whether they
want to have smaller SPL binary at the cost of slower boot.
Therefore dependency on CONFIG_SPL_DM_SPI, CONFIG_SPL_SPI_FLASH_SUPPORT,
CONFIG_SPL_SPI_LOAD, CONFIG_SPL_SPI_SUPPORT, CONFIG_SPL_DM_GPIO,
CONFIG_SPL_DM_MMC, CONFIG_SPL_GPIO_SUPPORT, CONFIG_SPL_LIBDISK_SUPPORT,
CONFIG_SPL_MMC_SUPPORT, CONFIG_SPL_SATA_SUPPORT and
CONFIG_SPL_LIBDISK_SUPPORT is changed from strict to related "imply"
(which can be selectivelly turned off and causes booting via BootROM).
Options CONFIG_SYS_SPI_U_BOOT_OFFS,
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR and
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_DATA_PART_OFFSET have to to be set to
zero as they define the location where kwbimage header starts. It is the
location where BootROM expects start of the kwbimage from which it reads,
parses and executes SPL part. The same applies to option
CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR, which has to be set to one.
Update all config files to set correct values of these options and set
CONFIG_SYS_U_BOOT_OFFS to the correct value - the offset where U-Boot
proper starts.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Platform specific BootROM may use its own image type for loading SPL or
U-Boot proper. In some cases it makes sense to not use BootROM supplied
code for booting U-Boot proper but rather to use U-Boot SPL for this,
e.g. when U-Boot SPL can load U-Boot proper faster than BootROM. In this
case it is required for platform board code to parse and load U-Boot in
BootROM specific image type.
This change adds support for parsing platform / board / BootROM specific
image types via weak function spl_parse_board_header() which is called
before marking boot image as a raw.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Some image types (e.g. kwbimage v1) store the offset to SPL binary and
offset to U-Boot proper binary in their headers. To avoid reading SPL
binary when loading U-Boot proper, add support for specifying offset in
struct spl_image_info, which defines the offset from the beginning of
the header and the beginning of the executable data.
Initial support is added only for SPI, MMC and SATA code. We can extend
it later if needed.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Rename this option so that CONFIG_IS_ENABLED can be used with it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
OP-TEE requires some particular setup, which is not needed for linux
or other payloads. Add a hook for platform-specific code to perform
any OP-TEE related configuration and initialization.
A weak function is used because it is symmetrical to other
spl_board_prepare_for_*() implementations. A solution to avoid the use
of weak functions would trivially apply to all these implementations.
However, re-designing this is beyond the scope of this patch.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
In general, Falcon mode means we're booting a linux kernel directly.
With FIT images, however, an OP-TEE secure kernel can be booted before
linux. Thus, if the next stage is an IH_OS_TEE, this isn't necessarily
a problem.
Of course, a general solution would involve mmc_load_image_raw_os()
only loading the binary, and leaving the decision of suitability to
someone else. However, a rework of the boot flow is beyond the scope
of this patch. Accept IH_OS_TEE as a valid OS value.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
It's possible that LOAD_FIT_FULL will have different values for TPL and
SPL, in which case just checking CONFIG_SPL_LOAD_FIT_FULL causes this to
be compiled in to the TPL even though functions and struct members it
depends on are not.
Use CONFIG_IS_ENABLED() to ensure the correct TPL/SPL variant is
checked.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If SPL fails to boot, try to provide an error code to indicate what is
wrong. For example, if a uclass is missing, this can return -EPFNOSUPPORT
(-96) which provides useful information.
Add a helper for accessing the image-loader name so we can drop the use
of #ifdefs in this code.
Put this feature behind a CONFIG_SHOW_ERRORS option to avoid increasing
the code size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Drop the _SUPPORT suffix so we can use CONFIG_IS_ENABLED() with this
option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Drop the _SUPPORT suffix so we can use CONFIG_IS_ENABLED() with this
option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
These option are named inconsistently with other SPL options, thus making
them incompatible with the CONFIG_IS_ENABLED() macro. Rename them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Factor out eMMC boot partition selection code into
default_spl_mmc_emmc_boot_partition() function and implement
weak spl_mmc_emmc_boot_partition(), so that architecture or
board code can override the eMMC boot partition selection.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Harald Seiler <hws@denx.de>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
When we do not have bootstage enabled, rather than include an empty
dummy function, we just don't reference it. This saves us space in some
tight builds. This also shows a few cases where show_boot_progress was
incorrectly guarded before.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
clk:
- Add driver for Xilinx Clocking Wizard IP
fdt:
- Also record architecture in /fit-images
net:
- Fix plat/priv data handling in axi emac
- Add support for 10G/25G speeds
pca953x:
- Add missing dependency on i2c
serial:
- Fix dependencies for DEBUG uart for pl010/pl011
- Add setconfig option for cadence serial driver
watchdog:
- Add cadence wdt expire now function
zynq:
- Update DT bindings to reflect the latest state and descriptions
zynqmp:
- Update DT bindings to reflect the latest state and descriptions
- SPL: Add support for ECC DRAM initialization
- Fix R5 core 1 handling logic
- Enable firmware driver for mini configurations
- Enable secure boot, regulators, wdt
- Add support xck devices and 67dr
- Add psu init for sm/smk-k26 SOMs
- Add handling for MMC seq number via mmc_get_env_dev()
- Handle reserved memory locations
- Add support for u-boot.itb generation for secure OS
- Handle BL32 handoffs for secure OS
- Add support for 64bit addresses for u-boot.its generation
- Change eeprom handling via nvmem aliases
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYN105QAKCRDKSWXLKUoM
IZiFAJ9CIiEpHiBbnAhA0VOMGoaXHGULywCdED/5dNgVtc1C7y4avzETbEyWzD4=
=CdMa
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.10' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.10
clk:
- Add driver for Xilinx Clocking Wizard IP
fdt:
- Also record architecture in /fit-images
net:
- Fix plat/priv data handling in axi emac
- Add support for 10G/25G speeds
pca953x:
- Add missing dependency on i2c
serial:
- Fix dependencies for DEBUG uart for pl010/pl011
- Add setconfig option for cadence serial driver
watchdog:
- Add cadence wdt expire now function
zynq:
- Update DT bindings to reflect the latest state and descriptions
zynqmp:
- Update DT bindings to reflect the latest state and descriptions
- SPL: Add support for ECC DRAM initialization
- Fix R5 core 1 handling logic
- Enable firmware driver for mini configurations
- Enable secure boot, regulators, wdt
- Add support xck devices and 67dr
- Add psu init for sm/smk-k26 SOMs
- Add handling for MMC seq number via mmc_get_env_dev()
- Handle reserved memory locations
- Add support for u-boot.itb generation for secure OS
- Handle BL32 handoffs for secure OS
- Add support for 64bit addresses for u-boot.its generation
- Change eeprom handling via nvmem aliases
On ARM64 secure OS can run as 64bit or 32bit that's why it is necessary to
record information about architecture that other code can read it and
properly pass it to TF-A and start in 64bit or 32bit mode.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
board_fit_image_post_process() passes only start and size of the image,
but type of the image is not passed. So pass fit and node_offset, to
derive information about image to be processed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Add defconfig and board support for HiFive Unmatched.
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
A lot of entries were using spaces instead of tab for alignment that's why
it is good to fix it to use the same style everywhere.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This has the uclass enforce calling detect() before other methods. This
allows drivers to cache information in detect() and perform (cheaper)
retrieval in the other accessors. This also modifies the only instance
where this sequencing was not followed.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This reverts commit 38d6b7ebda.
struct global_data contains a pointer to the bd_info structure. This
pointer was populated spl_set_bd() to a pre-allocated bd_info in the
".data" section. The referenced commit replaced this mechanism to one
that uses malloc(). That new mechanism is only used if SPL_ALLOC_BD=y.
which very few boards do.
The result is that (struct global_data)->bd is NULL in SPL on most
platforms. This breaks falcon mode, since arch_fixup_fdt() tries to
access (struct global_data)->bd and set the "/memory" node in the
devicetree. The result is that the "/memory" node contains garbage
values, causing linux to panic() as it sets up the page table.
Instead of trying to fix the mess, potentially causing other issues,
revert to the code that worked, while this change is reworked.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The 'firmware' property of a config node takes precedence over the
'kernel' property. 'standalone' is deprecated. However, give users a
couple of releases where 'standalone' still works, but warns loudly.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
U-Boot expects the FDT to be located right after the _end
linker symbol (see fdtdec.c: board_fdt_blob_setup())
The "basic" LOAD_FIT path is aware of this limitation, and relocates
the FDT at the expected location. Guessing the expected location
probably only works reliably on 32-bit arm, and it feels like a hack.
One proposal would be to pass the FDT address to u-boot
(e.g. using 'r2' on arm platforms).
The variable is named "fdt_hack" to remind future contributors that,
"hey! we should fix the underlying problem". However, that is beyond
the scope of this patch.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The information on the OS should be contained in the FIT, as the
self-explanatory "os" property of a node under /images. Hard-coding
this to U_BOOT might send us down the wrong path later in the boot
process.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The correct FDT to use is described by the "fdt" property of the
configuration node. When the fit_unamep argument to fit_image_load()
is "fdt", we get the "/images/fdt" node. This is incorrect, as it
ignores the "fdt" property of the config node, and in most cases,
the "/images/fdt" node doesn't exist.
Use NULL for the 'fit_unamep' argument. With NULL, fit_image_load()
uses the IH_TYPE_FLATDT value to read the config property "fdt",
which points to the correct FDT node(s).
fit_image_load() should probably be split into a function that reads
an image by name, and one that reads an image by config reference. I
don't make those decisions, I just point out the craziness.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit 4afc4f37c7 ("doc: FIT image: Clarify format and simplify
syntax") and delegated FPGA images to be added via the list of
"loadables" in lieu of the "fpga" property. Now actually implement
this in code.
Note that the "compatible" property is ignored for the time being, as
implementing "compatible" loading is beyond the scope of this change.
However, "u-boot,fpga-legacy" is accepted without warning.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Commit 4afc4f37c7 ("doc: FIT image: Clarify format and simplify
syntax") requires that FPGA images be referenced through the
"loadables" in the config node. This means that "fpga" properties in
config nodes are deprecated.
Given that there are likely FIT images which use "fpga", let's not
break those right away. Print a warning message that such use is
deprecated, and give users a couple of releases to update their
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The FPGA loading code in spl_simple_fit_read() can easily be separated
from the rest of the logic. It is split into two functions instead of
one because spl_fit_upload_fpga() is used in a subsequent patch.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
spl_load_fit_image() will try to load an image at the address given
in the "load" property. Absent such property, it uses
image_info->load_addr
Correct use of this is demonstrated in spl_fit_append_fdt(), which
resets the 'load_addr' before each spl_load_fit_image() call.
On the other hand loading "loadables" loop in spl_load_simple_fit()
completely ignores this. It re-uses the same structure, but doesn't
reset load_addr. If loadable [i] does not have a "load" property, its
load address defaults to load_addr, which still contains the address
of loadable [i - 1].
A simple solution is to treat NULL as an invalid load address. The
caller can set load_addr = 0 to request an abort if the "load"
property is absent.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a weak nand_get_mtd function for nand drivers to provide mtd info
and use this to set pagesize such that reading of non page-aligned
elements can succeed.
The spl_load_simple_fit already handles block block access so all we
need to do is provide the nand writesize as the block length.
Further cleanup of the drivers which use nand_spl_loaders.c such as
am335x_spl_bch.c, atmel_nand.c, and nand_spl_simple.c could be done
using info from mtd_info instead of statically defined details.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
commit 9f6a14c47f ("spl: fit: nand: fix fit loading in case of bad blocks")
added support for adjusting the image offset to account for bad blocks.
However this requires nand_spl_adjust_offset() which requires fully defined
specifics of the NAND chip being used may not be avialable.
Allow skipping this support for drivers or configs which don't specify
the NAND chip details statically with defines.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In preparation to add SiFive Unmatched board support, let's rename
the existing fu540 board to unleashed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The _SUPPORT suffix is from an earlier time and interferes with use of
the CONFIG_IS_ENABLED() macro. Rename the option to drop the suffix.
Tidy up the TODO that prompted this.
Signed-off-by: Simon Glass <sjg@chromium.org>
We have two separate places that need to figure out the bootstage ID to
use. Put this code in a function so that the logic is in one place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some systems (e.g. x86 APL) run SPL from read-only memory. The device
instances created by dtoc are therefore not writeable. To make things work
we would need to copy the devices to read/write memory.
To avoid this, add an option to use a separate runtime struct for devices,
just as is done for drivers. This can be used to hold information that
changes at runtime, avoiding the need for a copy.
Also add a Kconfig option for read-only SPL, which selects this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this casts addresses to pointers so cannot work with sandbox.
Update the code to use map_sysmem() instead.
As part of this change, the existing load_ptr is renamed to src_ptr since
it is not a pointer to load_addr. It is confusing to use a similar name
for something that is not actually related. For the alignment code,
ALIGN() is used instead of open-coded alignment. Add a comment to the line
that casts away a const.
Use a (new) load_ptr variable to access memory at address load_addr.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is printed twice but we only need one message, since there is very
little processing in between them. Drop the second one, since all branches
of the switch() already have output. Update the U-Boot message to include
the phase being jumped to.
Signed-off-by: Simon Glass <sjg@chromium.org>
When a FIT config specifies a devicetree, we should load it, no
questions asked. In the case of the "simple" FIT loading path, a
difficulty arises in selecting the load address of the FDT.
The default FDT location is right after the "kernel" or "firmware"
image. However, if that is an OP-TEE image, then the FDT may end up in
secure DRAM, and not be accessible to normal world kernels.
Although the best solution is to be more careful about the FDT
address, a viable workaround is to only append the FDT after a u-boot
or Linux image. This is identical to the previous logic, except that
FDT loading is extended to IH_OS_LINUX images.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Use the IS_ENABLED() macro to control code flow, instead of the
caveman approach of sprinkling #ifdefs. Code size is not affected, as
the linker garbage-collects unused functions. However, readability is
improved significantly.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The configuration node a sub node under "/configurations", which
describes the components to load from "/images". We only need to
locate this node once.
However, for each component, spl_fit_get_image_name() would parse the
FIT image, looking for the correct node. Such work duplication is not
necessary. Instead, once the node is found, cache it, and re-use it.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a desired configuration is not found, conf_node will have a
negative value. Thus the for loop will start at the root "/" node of
the image, print the "/description" property, and stop.
It appears the intent of the loop was to print the names of the
subnodes under "/configurations". We would need the offset to the
"/configurations" node, which is abstracted by fit_find_config_node().
This change agrees that abstracting the node offset is the correct
design, and we shouldn't be parsing the configurations manually. Thus
the loop in spl_fit_get_image_name() is useless. Remove it.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Several loose arguments describe the FIT image. They are thus related,
and it makes sense to pass them together, in a structure. Examples
include the FIT blob pointer, offset to FDT nodes, and the offset to
external data.
Use a spl_fit_info structure to group these parameters.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The logical steps in spl_load_simple_fit() are difficult to follow.
I think the long comments, ifdefs, and ungodly number of variables
seriously affect the readability. In particular, it violates section 6
of the coding style, paragraphs (3), and (4).
The purpose of this patch is to improve the situation by
- Factoring out initialization and parsing to separate functions
- Reduce the number of variables by using a context structure
This change introduces no functional changes.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The size is derived from the FIT image itself. Any alignment
requirements are machine-specific and known by the board code. Thus
the total length can be derived from the FIT image and knowledge of
the platform. The 'length' argument is redundant. Remove it.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CC: Matt Porter <mporter@konsulko.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
It is useful to know the TEXT_BASE value for the image being loaded in
TPL/SPL. Add a new spl_get_image_text_base() function to handle this.
Make use of this in the x86 SPL handler, instead of having the logic
there.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is useful to be able to figure out which phase we are loading next and
which phase we came from. Add some functions to handle this as well as
returning the name of a phase. This allows messages like "Booting to x"
where x is the next phase.
At present, TPL says 'Jumping to U-Boot' at the end, when in fact it is
jumping to SPL. This is confusing, so use the new functions to correct
this.
Tests for this will come with an upcoming minor SPL test refactor.
Signed-off-by: Simon Glass <sjg@chromium.org>
This commit add an option TPL_BOOTCOUNT_LIMIT to
use bootcount on TPL.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
H616 supports and needs bigger SPL than 32 KiB, mostly due to big DRAM
driver and need for PMIC configuration, which pulls several drivers which
are not needed otherwise.
spl_mmc_get_uboot_raw_sector() will now compare pre-configured size with
that, reported in SPL header. If size in header is bigger, it will use
that value instead.
In the process of function rework, also add missing function argument.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
It turns out that there are at least 2 other SoCs which have basically
the same memory map, similar clocks and other features as H6. It's very
likely that we'll see more such SoCs in the future. In order to ease
porting to new SoCs and lower ifdef clutter, introduce common symbol for
them.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When the hash check fails on a loadable image, the SPL/TPL simply
jump to the next one. This commit changes this behaviour, when the
hash check fails on a loadable image, the function spl_load_simple_fit
stops and report an error.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_HANDOFF is used in u-boot proper to locate handoff info from SPL
during pre-relocation init (in setup_spl_handoff). Add explicit dependency
on CONFIG_SPL, to fix the following build error when CONFIG_HANDOFF &&
!CONFIG_SPL:
common/board_f.c: In function ‘setup_spl_handoff’:
common/board_f.c:283:4: error: ‘gd_t {aka struct global_data}’
has no member named ‘spl_handoff’
gd->spl_handoff = bloblist_find(BLOBLISTT_SPL_HANDOFF,
^~
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This uses up space in the SPL binary but it always starts as zero. Also
some boards cannot support data in TPL (e.g. Intel Apollo Lake).
Use malloc() to allocate this structure instead, by moving the init a
little later, after malloc() is inited. Make this function optional since
it pulls in malloc().
This reduces the TPL binary size on coral by about 64 bytes
Signed-off-by: Simon Glass <sjg@chromium.org>
Fit images were loaded to a buffer provided by spl_get_load_buffer().
This may work when the FIT image is small and fits between the start
of DRAM and SYS_TEXT_BASE.
One problem with this approach is that the location of the buffer may
be manipulated by changing the 'size' field of the FIT. A maliciously
crafted FIT image could place the buffer over executable code and be
able to take control of SPL. This is unacceptable for secure boot of
signed FIT images.
Another problem is with larger FIT images, usually containing one or
more linux kernels. In such cases the buffer be be large enough so as
to start before DRAM (Figure I). Trying to load an image in this case
has undefined behavior.
For example, on stm32mp1, the MMC controller hits a RX overrun error,
and aborts loading.
_________________
| FIT Image |
| |
/===================\ /=====================\
|| DRAM || | DRAM |
|| || | |
||_________________|| SYS_TEXT_BASE | ___________________ |
| | || FIT Image ||
| | || ||
| _________________ | SYS_SPL_MALLOC_START || _________________ ||
|| malloc() data || ||| malloc() data |||
||_________________|| |||_________________|||
| | ||___________________||
| | | |
Figure I Figure II
One possibility that was analyzed was to remove the negative offset,
such that the buffer starts at SYS_TEXT_BASE. This is not a proper
solution because on a number of platforms, the malloc buffer() is
placed at a fixed address, usually after SYS_TEXT_BASE. A large
enough FIT image could cause the malloc()'d data to be overwritten
(Figure II) when loading.
/======================\
| DRAM |
| |
| | CONFIG_SYS_TEXT_BASE
| |
| |
| ____________________ | CONFIG_SYS_SPL_MALLOC_START
|| malloc() data ||
|| ||
|| __________________ ||
||| FIT Image |||
||| |||
||| |||
Figure III
The solution proposed here is to replace the ad-hoc heuristics of
spl_get_load_buffer() with malloc(). This provides two advantages:
* Bounds checking of the buffer region
* Guarantees the buffer does not conflict with other memory
The first problem is solved by constraining the buffer such that it
will not overlap currently executing code. This eliminates the chance
of a malicious FIT being able to replace the executing SPL code prior
to signature checking.
The second problem is solved in conjunction with increasing
CONFIG_SYS_SPL_MALLOC_SIZE. Since the SPL malloc() region is
carefully crafted on a per-platform basis, the chances of memory
conflicts are virtually eliminated.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
bl2_to_bl31_params_mem is just an implementation detail of the SPL ATF
support and is not needed anywhere else. Move it from the header to the
actual module.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Move the actual implementation of the bl2_plat_get_bl31_params() to its
own function. The weak function will just call the default
implementation. This has the advantage that board code can still call
the original implementation if it just want to modify minor things.
Signed-off-by: Michael Walle <michael@walle.cc>
There is no need to have the storage available globally. This is also a
preparation for LOAD_IMAGE_V2 support. That will introduce a similar
generator function which also has its own storage.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Michal Simek <michal.simek@xilinx.com>
This commit add the support of signature check for config node
in spl/tpl when the function spl_load_simple_fit is used.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This uclass is intended to provide a way to obtain information about a
U-Boot board. But the concept of a U-Boot 'board' is the whole system,
not just one circuit board, meaning that 'board' is something of a
misnomer for this uclass.
In addition, the name 'board' is a bit overused in U-Boot and we want to
use the same uclass to provide SMBIOS information.
The obvious name is 'system' but that is so vague as to be meaningless.
Use 'sysinfo' instead, since this uclass is aimed at providing information
on the system.
Rename everything accordingly.
Note: Due to the patch delta caused by the symbol renames, this patch
shows some renamed files as being deleted in one place and created in
another.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
SPL is creating fit-images DT node when loadables are recorded in selected
configuration. Entries which are created are using entry-point and
load-addr property names. But there shouldn't be a need to use non standard
properties because entry/load are standard FIT properties. But using
standard FIT properties enables option to use generic FIT functions to
descrease SPL size. Here is result for ZynqMP virt configuration:
xilinx_zynqmp_virt: spl/u-boot-spl:all -82 spl/u-boot-spl:rodata -22 spl/u-boot-spl:text -60
The patch causes change in run time fit image record.
Before:
fit-images {
uboot {
os = "u-boot";
type = "firmware";
size = <0xfd520>;
entry-point = <0x8000000>;
load-addr = <0x8000000>;
};
};
After:
fit-images {
uboot {
os = "u-boot";
type = "firmware";
size = <0xfd520>;
entry = <0x8000000>;
load = <0x8000000>;
};
};
Replacing calling fdt_getprop_u32() by fit_image_get_entry/load() also
enables support for reading entry/load properties recorded in 64bit format.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The sandbox is built with the SDL2 library with invokes the X11 library
which in turn calls getc(). But getc() in glibc is defined as
int getc(FILE *)
This does not match our definition.
int getc(void)
The sandbox crashes when called with parameter -l.
Rename our library symbol getc() to getchar().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_{SPL,TPL}_SIZE_LIMIT are defined as hex (SPL_SIZE_LIMIT was
converted in b51882d0 ("spl: Convert CONFIG_SPL_SIZE_LIMIT to hex"), but
there are still places that reference integer values. Change those to hex
as well. Also, update the Makefile to check for 0x0 instead of 0.
This also fixes the following build error when CONFIG_SPL_SIZE_LIMIT
is set by menuconfig to 0x0:
...
spl/u-boot-spl.bin exceeds file size limit:
limit: 0 bytes
actual: 0x80f0 bytes
excess: 0x80f0 bytes
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some boards, specifically 64-bit Allwinner boards (sun50i), are
extremely limited on SPL size. One strategy that was used to make space
was to remove the FIT "os" property parsing code, because it uses a
rather large lookup table.
However, this forces the legacy FIT parsing code path, which requires
the "firmware" entry in the FIT to reference the U-Boot binary, even if
U-Boot is not the next binary in the boot sequence (for example, on
sun50i boards, ATF is run first).
This prevents the same FIT image from being used with a SPL with
CONFIG_SPL_FIT_IMAGE_TINY=n and CONFIG_SPL_ATF=y, because the boot
method selection code looks at `spl_image.os`, which is only set from
the "firmware" entry's "os" property.
To be able to use CONFIG_SPL_ATF=y, the "firmware" entry in the FIT
must be ATF, and U-Boot must be a loadable. For this to work, we need to
parse the "os" property just enough to tell U-Boot from other images, so
we can find it in the loadables list to append the FDT, and so we don't
try to append the FDT to ATF (which could clobber adjacent firmware).
So add the minimal code necessary to distinguish U-Boot/non-U-Boot
loadables with CONFIG_SPL_FIT_IMAGE_TINY=y. This adds about 300 bytes,
much less than the 7400 bytes added by CONFIG_SPL_FIT_IMAGE_TINY=n.
Acked-by: Patrick Wildt <patrick@blueri.se>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This reverts commit eb39d8ba5f.
The commit breaks booting of fitImage by SPL, the system simply hangs.
This is because on arm32, the fitImage and all of its content can be
aligned to 4 bytes and U-Boot expects just that.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Reuben Dowle <reuben.dowle@4rf.com>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Marek Vasut <marex@denx.de>
ATF support was all the time based on FIT image support but this dependency
is not recorded anywhere.
For !SPL_FIT && SPL_ATF there is compilation error:
common/spl/spl.c: In function 'board_init_r':
common/spl/spl.c:689:26: error: 'struct spl_image_info' has no member named 'fdt_addr'
689 | spl_fixup_fdt(spl_image.fdt_addr);
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch does sed 's/SPL_FPGA_SUPPORT/SPL_FPGA/g' but also fixing Makefile
and zynqmp.c to simplify if/endif logic in zynqmp.c.
This change is mostly done to be able to use CONFIG_IS_ENABLED macro and
obj-$(CONFIG_$(SPL_)FPGA) in Makefile. For them symbols need to be in sync.
And removing one line from Topic Miami boards which is not needed because
symbol is not enabled via Kconfig.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
usb_init() may be called multiple times for fetching multiple images
from SPL. Skip reinitializing USB if its already been done
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Create a new API spl_usb_load() that takes the filename as a parameter
instead of taking the default U-boot PAYLOAD_NAME
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
