sandbox_flattree enables QCOM_PMIC_GPIO which now depends on BUTTON. As
a result the button tests now get run, but fail because the ADC and GPIO
button drivers aren't enabled.
Enable them to run the tests for sandbox_flattree.
Reported-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The boot0/1 feature uses simple CRC8 to check (in SPL) if
SPI-NOR content is not corrupted, hence the need to enable
it.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This function is defined by bootstd so using it precludes using that
feature. Use the board_early_init_r() feature instead.
Nove the affected code into a new file, so that it is clear that
this relates to board init.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
After the re-sync with Linux kernel (v6.0) of the XEA DTS
(SHA1: 7d08ddd09b) the alias
for SPI bus, to which SPI-NOR memory is connected, has changed from
'spi3' to 'spi2'.
To be in sync with current u-boot's xea dts, the default bus number
(which allows running 'sf probe' without any extra parameters given)
has been adjusted.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
phyGATE-Tauri-L-iMX8MM is a Gateway based on the phycore-imx8mm SoM.
As a result, all the board code of the phycore-imx8mm is used.
Device tree synced with kernel v6.7.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Reviewed-by: Teresa Remmet <t.remmet@phytec.de>
There is a new eDPU revision that uses Marvell 88E6361 switch onboard.
We can rely on detecting the switch to enable and fixup the Linux DTS
so a single DTS can be used.
There is currently no support for the 88E6361 switch and thus no working
networking in U-Boot, so we disable both ports.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Enabled the default utilization of the NFS command across all Xilinx
platforms to facilitate the booting of images through the network
using the NFS protocol.
Fixes: 10de125707 ("disable NFS support by default")
Signed-off-by: Tejas Bhumkar <tejas.arvind.bhumkar@amd.com>
Link: https://lore.kernel.org/r/20240104045217.2966454-1-tejas.arvind.bhumkar@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support for the Variscite VAR-SOM-IMX93 evaluation kit. The SoM
consists of an NXP iMX93 dual A55 CPU. The SoM is mounted on a Variscite
Symphony SBC.
Signed-off-by: Mathieu Othacehe <m.othacehe@gmail.com>
Implement fdtdec_board_setup() auto-detection of ethernet PHY.
This uses properties of the hardware and pull resistor placement.
If GPIO1_16 RGMII_MDC is HIGH, then R530 (MX8MM eDM SBC) or
R390 (MX8MP eDM SBC) is populated. R530 or R390 is populated
only on boards with AR8031 PHY.
If GPIO1_16 RGMII_MDC is LOW, then the in-SoM pull down is the
dominant pull resistor. This is the case on boards with BCM54213PE
PHY.
In case AR8031 PHY is populated, the PHY MDIO address is 0, in
case BCM54213PE PHY is populated, the PHY MDIO address is 1, the
fdtdec_board_setup() is used to patch the correct address into
the U-Boot control DT.
Enable broadcom PHY support to support both PHYs.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
We do not have a need to share a single console with the evaluation
board and disabling this option reduces the complexity of configuring
the consoles. Disable CONSOLE_MUX
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Some of the regulators we need to successfully boot are fixed
regulators. Enable the driver to properly probe them.
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Francis Laniel <francis.laniel@amarulasolutions.com> says:
During 2021 summer, Sean Anderson wrote a contribution to add a new shell, based
on LIL, to U-Boot [1, 2].
While one of the goals of this contribution was to address the fact actual
U-Boot shell, which is based on Busybox hush, is old there was a discussion
about adding a new shell versus updating the actual one [3, 4].
So, in this series, with Harald Seiler, we updated the actual U-Boot shell to
reflect what is currently in Busybox source code.
Basically, this contribution is about taking a snapshot of Busybox shell/hush.c
file (as it exists in commit 37460f5da) and adapt it to suit U-Boot needs.
This contribution was written to be as backward-compatible as possible to avoid
breaking the existing.
So, the modern hush flavor offers the same as the actual, that is to say:
1. Variable expansion.
2. Instruction lists (;, && and ||).
3. If, then and else.
4. Loops (for, while and until).
No new features offered by Busybox hush were implemented (e.g. functions).
It is possible to change the parser at runtime using the "cli" command:
=> cli print
old
=> cli set modern
=> cli print
modern
=> cli set old
The default parser is the old one.
Note that to use both parser, you would need to set both
CONFIG_HUSH_MODERN_PARSER and CONFIG_HUSH_OLD_PARSER.
In terms of testing, new unit tests were added to ut to ensure the new behavior
is the same as the old one and it does not add regression.
Nonetheless, if old behavior was buggy and fixed upstream, the fix is then added
to U-Boot [5].
In sandbox, all of these tests pass smoothly:
=> printenv board
board=sandbox
=> ut hush
Running 20 hush tests
...
Failures: 0
=> cli set modern
=> ut hush
Running 20 hush tests
...
Failures: 0
Thanks to the effort of Harald Seiler, I was successful booting a board:
=> printenv fdtfile
fdtfile=amlogic/meson-gxl-s905x-libretech-cc.dtb
=> cli get
old
=> boot
...
root@lepotato:~#
root@lepotato:~# reboot
...
=> cli set modern
=> cli get
modern
=> printenv fdtfile
fdtfile=amlogic/meson-gxl-s905x-libretech-cc.dtb
=> boot
...
root@lepotato:~#
This contribution indeed adds a lot of code and there were concern about its
size [6, 7].
With regard to the amount of code added, the cli_hush_upstream.c is 13030 lines
long but it seems a smaller subset is really used:
gcc -D__U_BOOT__ -E common/cli_hush_upstream.c | wc -l
2870
Despite this, it is better to still have the whole upstream code for the sake of
easing maintenance.
With regard to memory size, I conducted some experiments for version 8 of this
series and for a subset of arm64 boards and found the worst case to be 4K [8].
Tom Rini conducted more research on this and also found the increase to be
acceptable [9].
If you want to review it - your review will really be appreciated - here are
some information regarding the commits:
* commits marked as "test:" deal with unit tests.
* commit "cli: Add Busybox upstream hush.c file." copies Busybox shell/hush.c
into U-Boot tree, this explain why this commit contains around 12000 additions.
* commit "cli: Port Busybox 2021 hush to U-Boot." modifies previously added file
to permit us to use this as new shell.
The really good idea of #include'ing Busybox code into a wrapper file to define
some particular functions while minimizing modifications to upstream code comes
from Harald Seiler.
* commit "cmd: Add new parser command" adds a new command which permits
selecting parser at runtime.
I am not really satisfied with the fact it calls cli_init() and cli_loop() each
time the parser is set, so your reviews would be welcomed.
* Other commits focus on enabling features we need (e.g. if).
The keymile board family is not compatible with modern hush parser.
Indeed, This boards used set_local_var() to store some variables as local shell.
They then used get_local_var() to retrieve the variables values.
Sadly, this two functions do not exist with CONFIG_HUSH_MODERN_PARSER.
A patch was proposed to use environment variables rather than local variables
but it does not tackle the problem, so complementary work is needed to make
this boards use CONFIG_HUSH_MODERN_PARSER.
Also, with CONFIG_HUSH_MODERN_PARSER, kirkwoord sheevaplug and phytec bk4r1 hit
their board limits, so better to stick with old hush.
Cc: Holger Brunck <holger.brunck@hitachienergy.com>
Link: https://marc.info/?l=u-boot&m=165541917618725&w=2
Signed-off-by: Francis Laniel <francis.laniel@amarulasolutions.com>
Enable MISC_INIT_R for ae350 to support CPU name detection
and re-sync the configs via make savedefconfig.
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
Apple machines do not have memory below 4G. Since U-Boot does
not support the SMBIOS 3 header structures this means we can't
support SMBIOS on these machines. Unfortunately the refactoring
of the SMBIOS code this cycle accidentally enabled it again.
Fixes: 53fab13a7b ("efi: Use the installed SMBIOS tables")
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass <sjg@chromium.org> says:
This series continues refactoring the bootm code to allow it to be used
with CONFIG_COMMAND disabled. The OS-handling code is refactored and
a new bootm_run() function is created to run through the bootm stages.
This completes the work.
A booti_go() function is created also, in case it proves useful, but at
last for now standard boot does not use this.
This is cmdd (part d of CMDLINE refactoring)
It depends on dm/bootstda-working
which depends on dm/cmdc-working
It is useful for sandbox to build as much code as possible. Enable
support for booting various other operating systems. Add the missing
cache functions.
These operating systems do not actually boot on sandbox, of course.
Signed-off-by: Simon Glass <sjg@chromium.org>
Disable CONFIG_SPL_LOAD_FIT_APPLY_OVERLAY, this is not required nor used
on verdin am62, disable it to save precious binary size.
Update defconfig using savedefconfig, this adds CONFIG_OF_LIBFDT_OVERLAY
explicitly.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This change configures Toradex Colibri iMX8X SoM USB
hub to bypass mode, and brings out of the reset state.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
-----BEGIN PGP SIGNATURE-----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=aBS6
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-next-20231220' of https://source.denx.de/u-boot/custodians/u-boot-amlogic into next
- Add support for new GXL MDIO mux, with driver and Linux DT sync from v6.4
Since implementation of pinctrl driver for T20 Paz00 can switch
to device tree pinmux setup along with remove of board pinmux
and some minor device tree and defconfig tweaks.
Tested-by: Agneli <poczt@protonmail.ch> # Toshiba AC100 T20
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Julien Masson <jmasson@baylibre.com> says:
This patch series add the support for the MediaTek MT8365 EVK Board [1].
Most of the code have been copied/adapted from Linux tag v6.7-rc2.
For now we only enable/test these features:
Boot, UART, Watchdog and MMC.
[trini: This includes two clocks not listed in the Linux binding, which
needs resyncing later]
This adds support for the MT8365 EVK board with the following
features enabled/tested: Boot, UART, Watchdog and MMC.
Signed-off-by: Julien Masson <jmasson@baylibre.com>
Sync Amlogic GXBB, GXL & GXM DTs from Linux v6.4, and also
switch to GXL MDIO MUX driver to adapt to DT change,
Most of the changes are only cosmetic or doesn't concern U-Boot,
the most important change for U-Boot is the GXL mdio mux compatible
switch to amlogic,gxl-mdio-mux.
Link: https://lore.kernel.org/r/20231213-u-boot-gxl-mdio-mux-v2-2-c56bb02a75ea@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Migrate to the new environment format and drop most of the config.h.
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
MicroBlaze V is new AMD/Xilinx soft-core 32bit RISC-V processor IP.
It is hardware compatible with classic MicroBlaze processor.
The patch contains initial wiring and configuration for initial HW design
with memory, cpu, interrupt controller, timers and uartlite console
(interrupt controller is listed but U-Boot is not using it).
Provided DT is just describing one configuration and should be taken only
as example.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Import DRAM timings generated by the DDR tool 3.31 which introduce assorted
tweaks to the DRAM controller settings. Furthermore, enable DBI to improve
noise resilience of the DRAM bus by reducing the number of bit changes on
the bus.
Reduce the DRAM rate to 3600 MTps to remove all remaining correctable errors
reported by EDAC . It is not entirely clear why the slightly faster setting
does produce sporadic correctable errors, while this one does not, but this
could be related to simpler PLL setting at 3600 MTps.
Enable inline ECC which is necessary to detect ECC errors and collect
statistics by the EDAC driver in Linux. This reduces the DRAM size by
64 MiB for each 512 MiB of DRAM, so for a 4 GiB device the available
DRAM size becomes 3.5 GiB and for 2 GiB device the available DRAM size
becomes 1.8 GiB.
Signed-off-by: Marek Vasut <marex@denx.de>
Display the STMicroelectronics logo with features VIDEO_LOGO and
SPLASH_SCREEN on stm32f469-disco board.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support to Orise Tech OTM8009A display on stm32f469-disco board.
It was necessary to retrieve the framebuffer address from the device tree
because the address returned by the video-uclass driver pointed to a memory
area that was not usable.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Import DRAM timings generated by the DDR tool 3.31 which introduce assorted
tweaks to the DRAM controller settings. Furthermore, enable DBI to improve
noise resilience of the DRAM bus by reducing the number of bit changes on
the bus.
Reduce the DRAM rate to 3600 MTps to remove all remaining correctable errors
reported by EDAC . It is not entirely clear why the slightly faster setting
does produce sporadic correctable errors, while this one does not, but this
could be related to simpler PLL setting at 3600 MTps.
Enable inline ECC which is necessary to detect ECC errors and collect
statistics by the EDAC driver in Linux. This reduces the DRAM size by
64 MiB for each 512 MiB of DRAM, so for a 4 GiB device the available
DRAM size becomes 3.5 GiB .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable CAAM in U-Boot to make crypto available early in the boot process.
This has a side-effect that in case an older kernel version contains a
broken CAAM initialization timeout code, initialization in bootloader
will help that old kernel version function correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable CAAM in U-Boot to make crypto available early in the boot process.
This has a side-effect that in case an older kernel version contains a
broken CAAM initialization timeout code, initialization in bootloader
will help that old kernel version function correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
- Add TPM support for venice boards
- Add networking support for imx93-evk
- Enable TCP, IPv6, wget for DHCOM and Data Modul boards
- Enable fastboot support for Toradex boards
- Allow pico-imx7d to boot from SD
- Enable fastboot for beacon imx8m beacon boards, disabled
SYS_CONSOLE_IS_IN_ENV
- Fix mxsboot to prevent NAND blocks being reported as bad
- Add imx8mm PWM clock support
- Several devicetree syncs with the kernel
- Add support for i.MX8MP Polyhex Debix Model A SBC
- Reworked ddr_load_train_firmware() to get a 50ms boot time improvement
Enable support for TCP protocol, wget, and IPv6 on this platform.
The former two allow users download payload into the U-Boot from
a web server, which may be more convenient or easier to set up
than TFTP server. The later is enabled to future proof the IP
stack on this platform.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable support for TCP protocol, wget, and IPv6 on this platform.
The former two allow users download payload into the U-Boot from
a web server, which may be more convenient or easier to set up
than TFTP server. The later is enabled to future proof the IP
stack on this platform.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable support for TCP protocol, wget, and IPv6 on this platform.
The former two allow users download payload into the U-Boot from
a web server, which may be more convenient or easier to set up
than TFTP server. The later is enabled to future proof the IP
stack on this platform.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add basic sandbox support for 'booti' so we can start to boot the test
ARMbian image. This is helpful in checking that it is parsed correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add fastboot support for Apalis iMX6, Colibri iMX6, Colibri iMX6ULL and
Colibri iMX7 boards. Remove CONFIG_FASTBOOT_BUF_SIZE from
colibri_imx7_emmc_defconfig to get the default value of 0x7000000 instead
of 0x10000000, to make it consistent with the other boards.
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Auto-starting the WDT can cause false reboots when the user
is not intentionally trying to use the WDT, so leave it off until
it is requested.
Signed-off-by: Adam Ford <aford173@gmail.com>
The hardware only supports a specific console port, so remove the
option to change the console location in the environment.
Signed-off-by: Adam Ford <aford173@gmail.com>
Auto-starting the WDT can cause false reboots when the user
is not intentionally trying to use the WDT, so leave it off until
it is requested.
Signed-off-by: Adam Ford <aford173@gmail.com>
The hardware only supports a specific console port, so remove the
option to change the console location in the environment.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Currently, the imx8mp_evk uses the non-DM code to initialize the PMIC.
Convert to DM_PMIC, which is the recommended way to access the PMIC.
While at it, fix multi-line comments style.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Sync the devicetree files used in the kernel for the imx8mm-phyboard-polis
with the corresponding devicetree files in U-Boot.
Replaced phycore-imx8mm.dts with kernel dts imx8mm-phyboard-polis-rdk.dts
Synced with kernel 6.5.0-rc1 commit
e752a4f9589c (arm64: dts: freescale: imx8mm-phyboard: Add I2C4 pinmuxing)
Signed-off-by: Cem Tenruh <c.tenruh@phytec.de>
Add support for the Polyhex Debix Model A SBC board.
It is an industrial grade single board computer based on
NXP's i.MX 8M Plus.
Currently supported interfaces are:
- Serial console
- Micro SD
- eQOS and FEC Ethernet
imx8mp-debix-model-a.dts is taken from Linux 6.3.
Signed-off-by: Gilles Talis <gilles.talis@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Currently, building imx8qm_dmsse20a1_defconfig leads to the following
warning:
aarch64-linux-ld.bfd: invalid origin for memory region .sdram
Fix it by using the same SPL memory layout as done in the imx8mq_evk.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Oliver Graute <oliver.graute@kococonnector.com>
In case of A/B update systems there should be an option to load the same
binary/binaries to different location and they should work.
Before this patch boot.bin with U-Boot SPL can be added to whatever 32k
offset in SPI and SPL finds u-boot.itb at CONFIG_SYS_SPI_U_BOOT_OFFS
offset. In case of A/B update systems that means that SPL is at different
locations but it still points to the same u-boot.itb which is not correct.
That's why include multiboot value to offset calculation to be able to
point to image from the same base.
It doesn't affect any current system which starts from 0 offset.
This patch also change Kria defconfig which uses A/B setup. Partition
A starts at multiboot 64, partition B at multiboot 496.
And also print message about used SPI offset which is useful for all cases.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/93903a53ad9358ae69991558b787f574797effbe.1699619666.git.michal.simek@amd.com
Enable the initial kria SOM specific configurations like pinctrl,
pinconf etc. Also add the environment file.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20231109042407.6123-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Commit 68dcbdd594 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset
Signed-off-by: Fabio Estevam <festevam@denx.de>
On an early revision of the imx8mp-evk that I have access to,
the MAC addresses fuses are not programmed, causing failure to bring
the Ethernet interfaces.
Fix this problema by selecting CONFIG_NET_RANDOM_ETHADDR so that
random MAC addresses are assigned and the Ethernet ports become
functional out of the box.
Signed-off-by: Fabio Estevam <festevam@denx.de>
USB host interface is not working on some Apalis Toradex carrier
boards with Apalis iMX8 SoM. This is due to USBH_EN pin, which
powers USB peripherals, having a strong pull-down on some boards,
and a weak pull-down on the others. This USBH_EN pin is left
unconfigured, which means it is in its default state at cold boot:
input with a strong pull-up. As a result, carrier boards with a
weak pull-down have this signal high enough to trigger power
delivery to USB peripherals, and opposite - boards with strong
pull-down on USBH_EN have this signal below the threshold needed
to trigger USB power delivery.
This change configures the USBH_EN pin as gpio hog, fixing this
issue for all Apalis carrier boards regardless of pull-down
resistor value.
Also, update apalis-imx8_defconfig via savedefconfig.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
- StarFive: Add StarFive watchdog driver
- VisionFive2: Support device tree overlay for VisionFive2 board
- Andes: Fix PLIC-SW setting
- RISC-V: Fix NVMe support by implying NVME_PCI for QEMU
- RISC-V: Fix binman for 64 bit format load address
Enable GETOPT so that 'bdinfo' command with getopt() support can be
tested in CI.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Since commit b96640cbfb ("ARM: meson: g12a: switch dwc2 otg to DM")
and commit e327e2affd ("ARM: meson: switch AXG & GX dwc2 otg to DM")
Amlogic boards now requires DM_USB_GADGET to have USB Gadget to work.
Add it to the boards configs as returned by:
$ grep -L DM_USB_GADGET $(grep -l CONFIG_USB_GADGET $(grep -l MESON configs/*))
Fixes: b96640cbfb ("ARM: meson: g12a: switch dwc2 otg to DM")
Fixes: e327e2affd ("ARM: meson: switch AXG & GX dwc2 otg to DM")
Link: https://lore.kernel.org/r/20231206-u-boot-m2s-fix-usb-gadget-v1-1-1c4c66cd10f3@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
The OrangePi Zero 3 is a small development board featuring the Allwinner
H618 SoC, shipping with up to 4GB of DRAM, Gigabit Ethernet, a micro-HDMI
connector and two USB sockets.
The board uses LPDDR4 DRAM and an X-Powers AXP313a PMIC, support for
which was recently added to U-Boot.
Add a defconfig file selecting the right drivers and DRAM options.
Since the .dts file was synced from the Linux kernel repo already, we
just need to add one line to the Makefile to actually build the .dtb.
The DRAM parameters were derived from the values found in the BSP DRAM
drivers on the SPI NOR flash.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mikhail Kalashnikov <iuncuim@gmail.com>
Tested-by: Bob McChesney <bob@electricworry.net>
Tested-by: Stephen Graf <stephen.graf@gmail.com>
The original H616 devices released about three years ago were typically
paired with an X-Powers AXP305 PMIC. Newer devices uses the smaller
AXP313, and there seem to be far more systems with this PMIC around now.
Remove the default AXP305 selection for the H616 SoC from the Kconfig,
and move the PMIC selection into the board defconfig files instead.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The OrangePi Zero 2 has a USB VBUS regulator, controlled by pin PC16.
This is correctly described in the DT, but the patches for supporting
this are still pending.
Meanwhile add our good old CONFIG_USB1_VBUS_PIN to the defconfig file,
to enable power on the USB port and allow using a USB flash drive, for
instance.
Fixes: 6acc5fa581 ("sunxi: H616: enable USB support for H616 boards")
Reported-by: Mikhail Kalashnikov <iuncuim@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
To quote the author:
"Scmi" command will be re-introduced per Michal's request.
The functionality is the same as I put it in my patch set of adding
SCMI base protocol support, but made some tweak to make UT, "ut dm
scmi_cmd," more flexible and tolerable when enabling/disabling a specific
SCMI protocol for test purpose.
Each commit may have some change history inherited from the preceding
patch series.
Test
====
The patch series was tested on the following platforms:
* sandbox
In this test, "scmi" command is tested against different sub-commands.
Please note that scmi command is for debug purpose and is not intended
in production system.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
Since required drivers were merged, we can safely clean up the
board and switch to DM based driver with device tree support.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Since required drivers were merged, we can safely clean up the
board and switch to DM based driver with device tree support.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Since required drivers were merged, we can safely clean up the
board and switch to DM based driver with device tree support.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Since required drivers were merged, we can safely clean up the
board and switch to DM based driver with device tree support.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
As correct default SYS_CONFIG_NAME value is now set in
board/samsung/axy17lte/Kconfig (in commit "board: samsung: Fix
SYS_CONFIG_NAME configs in axy17lte Kconfig"), the SYS_CONFIG_NAME
option can be safely removed from all a*y17lte defconfigs. That removal
doesn't change resulting .config files.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
None of these platforms enabled a networking devices, and disabled
CMD_NET. Given that we used to gate network support on CMD_NET rather
than NET, we disable CONFIG_NET on these platforms now.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The initcall sequence fails at arch_misc_init. Disable misc init until
driver model and DT are clean.
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
These targets use NAND FLASH only. Maybe some MMC definitions were added by
trying MMC for the etamin target evaluation and were not removed.
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
Draco is a family of 3 boards: thuban, rastaban & etamin. Rename all
targets of the family adding the draco- prefix to increase readibility
and simplify future commits about concerning all boards of the family.
The name draco was initially used for the first target. It's deprecated
since a 2nd target was introduced. Unfortunately the draco target was
copied to the thuban target instead to be renamed. Remove it to save
unnecessary maintenance effort.
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
Move beagleplay support away from ti/am62x to it's own beagle vendor
folder.
This forms the starting point for new beagle platforms added under it's
own board vendor folder.
As part of this create all the associated files with a bare minimum
beagleplay.c file.
Suggested-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
[trini: Update k3-binman.dtsi to use full path to scheme.yaml now]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add am62x_beagleplay_* defconfig customized for the configuration of
BeaglePlay and drop the config fragments.
This is in preparation for dropping the dependency on ti vendor folder
entirely.
Signed-off-by: Nishanth Menon <nm@ti.com>
Switch to using bootstd. Note with this change, we will stop using
distro_bootcmd and instead depend entirely on bootflow method of
starting the system up.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Kernel commit 1b77265626a4 ("arm64: dts: ti: k3-j7200-mcu-wakeup: Add
HyperBus node") was merged to kernel without its dependent patch [1].
Similar fix is needed in U-Boot, and hbmc currently breaks boot. Till
this gets fixed in U-Boot, disable the config by default so that the
hbmc probe that happens in board/ti/j721e/evm.c will not take place
and lead to boot failure.
This is similar to the approach in commit 5b2671594b ("configs:
j721e: Remove HBMC_AM654 config"), introduced to j7200 evm platform.
[1] https://lore.kernel.org/all/20230424184810.29453-1-afd@ti.com/
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
