The EVM architecture for J721S2 is similar to that of J721E and J7200. It
is as follows,
+------------------------------------------------------+
| +-------------------------------------------+ |
| | | |
| | Add-on Card 1 Options | |
| | | |
| +-------------------------------------------+ |
| |
| |
| +-------------------+ |
| | | |
| | SOM | |
| +--------------+ | | |
| | | | | |
| | Add-on | +-------------------+ |
| | Card 2 | | Power Supply
| | Options | | |
| | | | |
| +--------------+ | <---
+------------------------------------------------------+
Common Processor Board
Common Processor board is the baseboard that contains most of the actual
connectors, power supply etc. The System on Module (SoM) is plugged on to
the common processor baord. Therefore, add support for peripherals brought
out in the common processor board.
Link to Common Processor Board: https://www.ti.com/lit/zip/sprr439
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
This adds initial support for the Toradex Verdin iMX8M Plus Quad 4GB WB
IT V1.0B module. They are strapped to boot from eFuses which are factory
fused to properly boot from their on-module eMMC. U-Boot supports
booting from the on-module eMMC only, SDP support is disabled for now
due to missing i.MX 8M Plus USB support.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet both on-module eQoS and FEC (requires PHY on carrier board)
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.
Boot:
U-Boot SPL 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
Quad die, dual rank failed, attempting dual die, single rank configuration.
Normal Boot
WDT: Started watchdog@30280000 with servicing (60s timeout)
Trying to boot from BOOTROM
Find img info 0x&48025a00, size 872
Need continue download 1024
Download 779264, Total size 780424
NOTICE: BL31: v2.2(release):rel_imx_5.4.70_2.3.2_rc1-5-g835a8f67b
NOTICE: BL31: Built : 16:52:37, Aug 26 2021
U-Boot 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
CPU: Freescale i.MX8MP[8] rev1.1 at 1200 MHz
Reset cause: POR
DRAM: 8 GiB
Core: 78 devices, 18 uclasses, devicetree: separate
WDT: Started watchdog@30280000 with servicing (60s timeout)
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Toradex Verdin iMX8M Plus Quad 4GB Wi-Fi / BT IT V1.0B, Serial# 06817281
Carrier: Toradex Verdin Development Board V1.1A, Serial# 10807609
Setting variant to wifi
Net: Hard-coding pdata->enetaddr
eth1: ethernet@30be0000, eth0: ethernet@30bf0000 [PRIME]
Hit any key to stop autoboot: 0
Verdin iMX8MP #
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add device tree files for suniv and
Lichee Pi Nano it is a board based on F1C100s.
dt-bindings/dts are synced with 5.16.0
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The Ten64 is a networking-oriented MiniITX board
using the NXP LS1088A SoC.
This patch provides the bare minimum to support
Ten64 boards under U-Boot for distroboot.
Some related drivers have not yet been submitted
and this basic support lacks some of the
opinionated defaults provided by our firmware
distribution.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Synchronize DH DHCOR DTs with Linux commit 25960cafa06e ("Linux 5.15.12").
There is no functional change to the resulting DTs. The eeprom0 alias is
now reinstated in SoM u-boot dtsi, the PHY reset GPIO is reinstated in AV96
u-boot dtsi.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This synchronizes the device trees with those that are in the
process of being upstreamed into Linux. This is mostly the
current state of the device trees on the asahilinux branch
with a few extra bits used by OpenBSD. This includes device
trees for machines that were still missing.
There are still some differences that will hopefully be resolved
soon.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEPVPGJshWBf4d9CyLd9zb2sjISdEFAmHYV8MACgkQd9zb2sjI
SdELkA/+LjyjJB1KI6/KLLg43zyFeeZX/SjQd5BUIx6EfaCgyTkuq2lzQnErGmbi
HoyMoNLpBxLIL27/5TXPzmKYAeOfKPxA/sXTTtx/l7PG8ncSZIoU0+utqjycdUsK
tSi7EdFzk7/kDDRkqqA7q9nxsPn/7GQNh/ZC9zstMXKaTO/TEb/sZWCMcvQ0MNoB
ynZKOCg5t60UkIYIRwZwC/OS/ssn86dovv/Aa/8D6qpL2AbS5DoCXHuAr8Dnz7fJ
q4rV7oLh7a+WHe/qC7R6ylYFIVVqY5JaIgbLDwuvk1z9o7txchMMQnGgllZ35sN9
LECD2iSDGjhPaHuGCvQwl3TWtIpvtdcP4sQTyJhsXNPxCG6HHvRz7xY4erUohR1I
LIddwCCHeCrBiaamXNbCzph2+JhfPSQ5ETCL9M6iBMxNUPunlCxjfjDzlT/pg11p
EO9PIPjRMR9QhxKtd3gZpyAqPuMBEmIwhDtHI6dL3DNOOsF44ObE4swnzS6qXIDn
jRZzFCC2f/Vyg11YnzFtV3A5eWwJahGDWAGAnnlg6Y8GCLlLmDJitcgA/rWSALko
T5fC8L8IFUx2RnHczyitJ/wqJl9FqOAnIaoB3Trpwp8gFQ15dQjbvoXldQnAjSS2
9bns3zOrx79EF4lbHhwNE9UDLm6OjK5vR3h4bGJvyZBmasVsA90=
=dLEg
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20220107' of https://source.denx.de/u-boot/custodians/u-boot-amlogic into next
- disable CONFIG_NET_RANDOM_ETHADDR when unnecessary on amlogic based configs
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
C.TOUCH 2.0 is a general purpose carrier board with capacitive
touch interface support.
10.1" OF is a capacitive touch 10.1" Open Frame panel solutions.
PX30.Core needs to mount on top of C.TOUCH 2.0 carrier with pluged
10.1" OF for creating complete PX30.Core C.TOUCH 2.0 10.1" Open Frame.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync the px30 devicetree files from linux-next tree.
commit <14ce8069f48b> ("lib/stackdepot: allow optional init and
stack_table allocation by kvmalloc() - fixup3")
Note, this path even sync rk3326 files as it depends on px30.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add an empty version of this file, so that we can at least build this
board when devicetrees are required.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an empty devicetree file for these boards. It seems to be possible to
obtain a real one from another bootloader called 'bolt' but I will leave
this to the maintainer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an empty file to prevent build errors when building with
CONFIG_OF_SEPARATE enabled.
Unfortunately there are no build instructions in the U-Boot tree to enable
a real file to be created.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an empty version of this file, so that we can at least build this
board when devicetrees are required.
The real devicetree is created by the Xen project on-the-fly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sync these file, obtained from Linux v5.15.
Add a note for the maintainer, and SPDX lines where they are missing.
The added lines are:
SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
Note, this matches the text in those files, but is not the same as the
GPL-2.0 of some files.
[1] https://releases.linaro.org/android/reference-lcr/juno/7.1-17.05/
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Sync these files, obtained from Linux v5.15.
This adds a devicetree file for rpi_4 which was not there before.
Testing shows no change so far as I can see:
- boots to U-Boot prompt on rpi0, rpi2
- boots to distro on rpi3
- boots to distro on rpi4
I am assuming that syncing with Linux is safe, but the maintainer should
know for sure.
Signed-off-by: Simon Glass <sjg@chromium.org>
This uses QEMU virt which creates its own devicetree.
Add an empty version of this file, so that we can at least build this
board when devicetrees are required.
Tested-by: Heinrich Schuchardt <heinrich.schuchardt@canaonical.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
This uses QEMU virt which creates its own devicetree.
Add an empty version of this file, so that we can at least build this
board when devicetrees are required.
Tested-by: Heinrich Schuchardt <heinrich.schuchardt@canaonical.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
sdhci:
- Fix emmc mini case with missing firmware interface
zynqmp:
- Restore JTAG interface if required
- Allow overriding board name
- Add support for DLC21
- Fix one fallthrought statement description
- Use config macro instead of name duplication
- Save multiboot to variable
firmware:
- Handle ipi_req errors better
- Use local buffer in case user doesn't need it instead of NULL/0 location
spi:
- gqsi: Fix write issue at low frequencies
net:
- gem: Disable broadcasts
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYZPDrwAKCRDKSWXLKUoM
IS9GAJ93T/uprhLcKWMb+284YMb2caWgOACfZ02nTlzvZKNNXVretJgZaHXqj1M=
=cwTL
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.01-rc3' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.01-rc3
sdhci:
- Fix emmc mini case with missing firmware interface
zynqmp:
- Restore JTAG interface if required
- Allow overriding board name
- Add support for DLC21
- Fix one fallthrought statement description
- Use config macro instead of name duplication
- Save multiboot to variable
firmware:
- Handle ipi_req errors better
- Use local buffer in case user doesn't need it instead of NULL/0 location
spi:
- gqsi: Fix write issue at low frequencies
net:
- gem: Disable broadcasts
Samsung Galaxy A3, A5, A7 (2017) - middle class Samsung smartphones.
U-boot can be used as chain-loaded bootloader to gain control
on booting vanilla linux(and possibly others) kernels
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Samsung S9 SM-G9600 - Snapdragon SDM845 version of the phone,
for China \ Hong Kong markets.
Has unlockable bootloader, unlike SM-G960U (American market version),
which allows running u-boot as a chain-loaded bootloader.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Add preliminary device trees for the Apple M1 mini (2020) and
Apple M1 Macbook Pro 13" (2020). Device tree bindings for
the Apple M1 SoC are still being formalized and these device
trees will be synchronized with the Linux kernel as needed.
The device trees in this commit are based on the initial Apple
M1 device trees from Linux 5.13, nodes for dart, pcie, pinctrl,
pmgr, usb based on bindings on track for inclusion in Linux
5.15 and 5.16 and nodes for i2c, mailbox, nvme, pmu, spmi and
watchdog that don't have a proposed binding yet.
These device trees are provided as a reference only as U-Boot
uses the device tree passed by the m1n1 bootloader.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add code to build the eMMC variant of the Colibri iMX6ULL, i.e. the
'Colibri iMX6ULL 1GB' which has a eMMC instead of the raw NAND used
on other SKUs.
Related-to: ELB-4056, ELB-4057
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This adds support for the NanoPi R1S H5 board.
Allwinner H5 SoC
512MB DDR3 RAM
10/100/1000M Ethernet x 2
RTL8189ETV WiFi 802.11b/g/n
USB 2.0 host port (A)
MicroSD Slot
Reset button
Serial Debug Port
WAN - LAN - SYS LED
The dts file is taken from Linux 5.14 tag.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The Kontron SoM-Line i.MX8MM (N801x) by Kontron Electronics GmbH is a SoM
module with an i.MX8M-Mini SoC, 1/2/4 GB LPDDR4 RAM, SPI NOR, eMMC and PMIC.
The matching evaluation boards (Board-Line) have 2 Ethernets, USB 2.0, HDMI/LVDS,
SD card, CAN, RS485 and much more.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
This adds support for i.MX6UL/ULL-based evaluation kits with SoMs by
Kontron Electronics GmbH.
Currently there are the following SoM flavors (SoM-Line):
* N6310: SOM with i.MX6UL-2, 256MB RAM, 256MB SPI NAND
* N6311: SOM with i.MX6UL-2, 512MB RAM, 512MB SPI NAND
* N6411: SOM with i.MX6ULL, 512MB RAM, 512MB SPI NAND
And the according evaluation boards (Board-Line):
* N6310-S: Baseboard with SOM N6310, eMMC, display (optional), ...
* N6311-S: Baseboard with SOM N6311, eMMC, display (optional), ...
* N6411-S: Baseboard with SOM N6411, eMMC, display (optional), ...
Currently U-Boot describes i.MX6UL and i.MX6ULL through separate config
options at compile-time. Though the differences are so minor, that for
the scope of these SoMs we just use a single defconfig that is compatible
with both SoCs.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Currently imx8mm-cl-iot-gate_defconfig fails to produce a working boot
binary due to the lack of fip.bin:
" BINMAN all
Image 'main-section' is missing external blobs and is non-functional: blob-ext
Some images are invalid"
To make the build process more consistent with the other i.MX8M targets,
split the defconfig in two:
- imx8mm-cl-iot-gate_defconfig: standard defconfig that only
requires ATF / DDR firmware.
- imx8mm-cl-iot-gate-optee_defconfig: "more advanced" defconfig that
requires ATF / Optee / mbedtls / DDR firmware.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Import the initial dts queued for Linux 5.16.y
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Alpha sort the Amlogic dtb list (same as the kernel).
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add support for new home automation devices.
JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation controller with the following features:
- DIN Rail Mounting case
- Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 512Mb/1GB DDR3
- 8/16GB eMMC flash
- 1 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- 2 x gpio LEDS
- GPIO user Button
- 1 x 1-Wire
- 2 x RS-485
- 4 x dry contact digital GPIO inputs
- 3 x relay GPIO outputs
- DC source with a voltage of 9 to 56 V / Passive POE
JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation controller with the following features:
- Square plastic case
- Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 1GB DDR3
- 8/16GB eMMC flash
- 2 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- MicroSD 2.x/3.x/4.x DS/HS cards.
- 1 x gpio LED
- ADC user Button
- DC source 5V microUSB with serial console
Patches from:
- JetHub H1
https://lore.kernel.org/r/20210915085715.1134940-4-adeep@lexina.inhttps://git.kernel.org/amlogic/c/abfaae24ecf3e7f00508b60fa05e2b6789b8f607
- JetHub D1
https://lore.kernel.org/r/20210915085715.1134940-5-adeep@lexina.inhttps://git.kernel.org/amlogic/c/8e279fb2903990cc6296ec56b3b80b2f854b6c79
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: removed unused variable value]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Import Amlogic DT changes from Linux commit 7d2a07b76933 ("Linux 5.14"),
dt-bindings clock changes and new meson-g12b-gsking-x.dts,
meson-sm1-bananapi-m5 & odroid-hc4 boards.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Prepares for the addition of the IOT2050 board which is based on the TI
AM65x. The board comes in four variants, Basic and Advanced, each as
product generation 1 (SR1.0) and 2 (SR2.x), so there are separate dts
files needed. Furthermore, the SPL has its own device tree.
Based on original board support by Le Jin, Gao Nian and Chao Zeng.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
We have individual SOC symbols for each keystone 2 platform. Use the
existing CONFIG_ARCH_KEYSTONE rather than CONFIG_SOC_KEYSTONE to
encompass all of the keystone families.
Signed-off-by: Tom Rini <trini@konsulko.com>
vexpress_ca9x4 is seemingly the only board except for qemu_arm which
is able to run U-Boot correctly, using the `-M vexpress-a9` option to
QEMU. Building for qemu_arm and running qemu-system-arm with the `-M
virt` argument has a number of downsides, most importantly that it
only supports virtio storage drivers. This significantly reduces its
usefulness in testing memory card and Flash solutions, especially when
the tested images are from a third party source.
So therefore we reintroduce the vexpress_ca9x4 board in this commit,
with the explicit goal of using it with QEMU.
A number of differences to note from the original:
* Since the board was apparently unmaintained, I have now set myself
as the maintainer.
* The board has been converted to use the driver model, which was the
reason it was removed in the first place.
* The vexpress_ca15_tc2 and vexpress_ca5x2 boards, which were removed
in the same commit, are not necessary for the QEMU use case, and
have been omitted.
* An `mmc0` alias was introduced in the dts file. The mmc is not
detected correctly without this, now that it's based on the device
tree instead of the board's init function.
* A couple of other nodes were removed because they were problematic
when trying to run the UEFI bootmgr. Once again, the primary use
case here is QEMU, and these nodes are not needed for that to work.
* Unnecessary board init code has been removed, thanks to driver model
and device tree.
* `CONFIG_OF_EMBED` has been enabled. I know this goes against
recommended practice, but there doesn't seem to be any other way to
pass the dtb to U-Boot in the QEMU scenario. Using the -dtb argument
does not work, I suppose because U-Boot doesn't use the same
mechanics as the kernel when it's booting.
* Load addresses have been changed to fit QEMU use case.
People wanting to get a more detailed, yet somewhat isolated, diff
between this and the original, can run this command:
git diff c6c26a05b89f25a06e7562f8c2071b60fd0c9eac~1 -- \
$( git diff-tree --diff-filter=A -r --name-only HEAD~1 HEAD)
(Make sure to either check out this commit first, or replace HEAD with
the commit ID of this commit)
Signed-off-by: Kristian Amlie <kristian.amlie@northern.tech>
xilinx:
- Disable CONFIG_ARCH_FIXUP_FDT_MEMORY
- Print information about cpu via soc drivers and enable DISPLAY_CPUINFO
- Wire infrastructure for DTB_RESELECT and MULTI_DTB_FIT
zynq:
- Wire single QSPI
- Use power-source instead of io-standard properties
- Enable nor on zc770-xm012
zynqmp:
- Change handling around multi_boot()
- Setup offset for u-boot.itb in spi
- Generate run time dfu_alt_info for capsule update
- Use explicit values for enums (zynqmp_firmware.h)
- Enable RTC/SHA1/BUTTON/BUTTON_GPIO command
- Disable WDT driver by default
- Bind usb/scsi via preboot because of EFI
- DT updates/fixes
- Add soc driver
- Fix SPL SPI boot mode
versal:
- Add soc driver
sdhci:
- Update tap delay programming for zynq_sdhci driver
cmd:
- Fix RTC uclass handling in date command
- Update pwm help message
- Update reset help message
watchdog:
- Fix wwdt compilation
rtc:
- Deal with seq alias in rtc uclass
- Add zynqmp RTC driver
fdt:
- Add kernel-doc for fdt_fixup_memory_banks()
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYSilpgAKCRDKSWXLKUoM
Id2JAJ9jY19JiEpOd3vuRCT5CE/pzX4yDACeP8DiXDzSi5tLHwDWUCBobUTze2s=
=5lnj
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.10-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.10-rc3
xilinx:
- Disable CONFIG_ARCH_FIXUP_FDT_MEMORY
- Print information about cpu via soc drivers and enable DISPLAY_CPUINFO
- Wire infrastructure for DTB_RESELECT and MULTI_DTB_FIT
zynq:
- Wire single QSPI
- Use power-source instead of io-standard properties
- Enable nor on zc770-xm012
zynqmp:
- Change handling around multi_boot()
- Setup offset for u-boot.itb in spi
- Generate run time dfu_alt_info for capsule update
- Use explicit values for enums (zynqmp_firmware.h)
- Enable RTC/SHA1/BUTTON/BUTTON_GPIO command
- Disable WDT driver by default
- Bind usb/scsi via preboot because of EFI
- DT updates/fixes
- Add soc driver
- Fix SPL SPI boot mode
versal:
- Add soc driver
sdhci:
- Update tap delay programming for zynq_sdhci driver
cmd:
- Fix RTC uclass handling in date command
- Update pwm help message
- Update reset help message
watchdog:
- Fix wwdt compilation
rtc:
- Deal with seq alias in rtc uclass
- Add zynqmp RTC driver
fdt:
- Add kernel-doc for fdt_fixup_memory_banks()
Start of DTB should be 64bit aligned that's why also make sure that end is
also 64bit aligned. It is not required but it is nice thing to do.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add device tree for N5X.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Ley Foon Tan <lftan.linux@gmail.com>
Add i.MX8ULP EVK basic support, support SD/I2C/ENET/LPUART
Log as below: I would keep some debug info for now, and after we move
to be stable and production launch, we could drop that.
U-Boot SPL 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800)
Normal Boot
upower_init: soc_id=48
upower_init: version:11.11.6
upower_init: start uPower RAM service
user_upwr_rdy_callb: soc=b
user_upwr_rdy_callb: RAM version:12.6
Turn on switches ok
Turn on memories ok
Clear DDR retention ok
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F0 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
complete
De-Skew PLL is locked and ready
WDT: Not found!
Trying to boot from BOOTROM
image offset 0x8000, pagesize 0x200, ivt offset 0x0
Load image from 0x3a800 by ROM_API
NOTICE: BL31: v2.4(release):imx_5.10.35_2.0.0_imx8ulp_er-10-gf37e59b94
NOTICE: BL31: Built : 01:56:58, Jun 29 2021
NOTICE: upower_init: start uPower RAM service
NOTICE: user_upwr_rdy_callb: soc=b
NOTICE: user_upwr_rdy_callb: RAM version:12.6
U-Boot 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800)
CPU: Freescale i.MX8ULP rev1.0 at 744 MHz
Reset cause: POR
Boot mode: Single boot
Model: FSL i.MX8ULP EVK
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 2
Loading Environment from MMC... ***
Warning - bad CRC, using default environment
In: serial@293a0000
Out: serial@293a0000
Err: serial@293a0000
Net:
Warning: ethernet@29950000 (eth0) using random MAC address -
96:35:88:62:e0:44
eth0: ethernet@29950000
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Make the conversion to driver model as it is mandatory.
Successfully tested booting Linux from the SD card.
Dropped support for networking and splash screen as these need
to be properly converted to DM and tested.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC
Do the following to add support for it:
- add dts
- add PMIC config
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
This device tree is imported from Linux 5.13.1 and enabled via the
am335x board file and the am335x evm defconfig.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Add device tree kirkwood-nsa310s.dts for Zyxel NSA310S board to
convert to Driver Model.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add the device tree for Akebi96. Akebi96 is a 96boards certified
development board based on UniPhier LD20.
( https://www.96boards.org/product/akebi96/ )
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
The Gateworks GW7901 is an ARM based single board computer (SBC)
featuring:
- i.MX8M Mini SoC
- LPDDR4 DRAM
- eMMC FLASH
- SPI FRAM
- Gateworks System Controller (GSC)
- Atmel ATECC Crypto Authentication
- USB 2.0
- Microchip GbE Switch
- Multiple multi-protocol RS232/RS485/RS422 Serial ports
- onboard 802.11ac WiFi / BT
- microSD socket
- miniPCIe socket with PCIe, USB 2.0 and dual SIM sockets
- Wide range DC power input
- 802.3at PoE
To add support for this board:
- add dts from Linux (accepted for v5.14)
- add SPL PMIC config
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
ZeroPi is a new board of high performance with low cost
designed by FriendlyElec., using the Allwinner H3 SOC.
ZeroPi features
- Allwinner H3, Quad-core Cortex-A7@1.2GHz
- 256MB/512MB DDR3 RAM
- microsd slot
- 10/100/1000Mbps Ethernet
- Debug Serial Port
- DC 5V/2A power-supply
Signed-off-by: Yu-Tung Chang <mtwget@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add basic support for running U-Boot on the Embedded Artists LPC3250
Developer's Kit v2 board by launching U-Boot from the board's s1l loader
(which comes pre-installed on the board).
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Add device trees for 96boards EE DeveloperBox and basement SynQuacer
SoC dtsi. These files are imported from EDK2
commit 83d38b0b4c0f240d4488c600bbe87cea391f3922
as-is (except for the changes #include path and some macros).
And add U-Boot specific changes in synquacer-sc2a11-developerbox-u-boot.dtsi
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Add board code for the R8A779A0 V3U Falcon board.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
--
Marek: - various small rebase fixes and clean ups
The EXPU1 design is a new 40G capable ethernet service unit card for
Hitachi-Powergrids wired-com product lines.
The base SoC is same as for already added SELI8 card, consequently the
already added u-boot support for SELI8 is reused.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
[Fixed new line error at EOF]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support for Storopack's SMEGW01 board, which is an
IoT gateway based on the i.MX7D SoC.
Based on the original U-Boot work done by Phytec.
Signed-off-by: Fabio Estevam <festevam@denx.de>
A simple prototyping board with one microSD port, one Ethernet port,
2 USB ports, I2C, SPI, GPIO, and UART interfaces.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Cc: Stefano Babic <sbabic@denx.de>
Board designed for quick prototyping and has one microSD port,
2 Ethernet ports, 2 USB ports, I2C, SPI, CAN, RS-485, GPIO,
UART interfaces, and 2 RGB LEDs.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Cc: Stefano Babic <sbabic@denx.de>
The patch contains several DT files for SOM platform.
Carrier card is sck-kv (KV260) revA/B. SMK-K26 is description for starter
kit which doesn't have EMMC populated. And SM-K26 is full som with EMMC.
Files are divided in this way to make sure that SOM can be plugged to
different carrier card and all peripherals on SOM (or defined by a spec) can
be used by U-Boot. Full DT for SOM+CC can be merged together as overlays.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds the dtsi/dts files needed to support the Marvell
Octeon TX2 CN913x DB. This is only the base port with not all
interfaces supported fully.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
AM642 StarterKit (SK) board is a low cost, small form factor board
designed for TI’s AM642 SoC. It supports the following interfaces:
* 2 GB LPDDR4 RAM
* x2 Gigabit Ethernet interfaces capable of working in switch and MAC mode
* x1 USB 3.0 Type-A port
* x1 UHS-1 capable µSD card slot
* 2.4/5 GHz WLAN + Bluetooth 4.2 through WL1837
* 512 Mbit OSPI flash
* x2 UART through UART-USB bridge
* XDS110 for onboard JTAG debug using USB
* Temperature sensors, user push buttons and LEDs
* 40-pin Raspberry Pi compatible GPIO header
* 24-pin header for peripherals in MCU island (I2C, UART, SPI, IO)
* 54-pin header for Programmable Realtime Unit (PRU) IO pins
* Interface for remote automation. Includes:
* power measurement and reset control
* boot mode change
Add basic support for AM642 SK.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The AM642 EValuation Module (EVM) is a board that provides access to
various peripherals available on the AM642 SoC, such as PCIe, USB 2.0,
CPSW Ethernet, ADC, and more.
Add basic support.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Supported peripherals: Ethernet, eMMC, Serial.
U-Boot SPL 2021.04-00911-g5fa1e2ffeb-dirty (Apr 23 2021 - 09:11:14
+0200)
Normal Boot
Trying to boot from MMC2
U-Boot 2021.04-00911-g5fa1e2ffeb-dirty (Apr 23 2021 - 09:11:14 +0200)
CPU: Freescale i.MX8MQ rev2.1 at 1000 MHz
Reset cause: POR
Model: Ronetix iMX8M-CM SoM
DRAM: 1 GiB
WDT: Started with servicing (60s timeout)
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Net:
Warning: ethernet@30be0000 (eth0) using random MAC address -
42:0d:e7:78:da:53
eth0: ethernet@30be0000
Hit any key to stop autoboot: 0
u-boot=>
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Engicam C.TOUCH 2.0 is an EDIMM compliant general purpose Carrier
board.
Genaral features:
- Ethernet 10/100
- Wifi/BT
- USB Type A/OTG
- Audio Out
- CAN
- LVDS panel connector
i.Core MX8M Mini is an EDIMM SoM based on NXP i.MX8M Mini from Engicam.
i.Core MX8M Mini needs to mount on top of this Carrier board for
creating complete i.Core MX8M Mini C.TOUCH 2.0 board.
Linux dts commit details:
commit <a142252061ff> ("arm64: dts: imx8mm: Add Engicam i.Core MX8M Mini
C.TOUCH 2.0")
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Engicam EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board.
Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Mini PCIe
- MIPI CSI
- 2x CAN
- Audio Out
i.Core MX8M Mini is an EDIMM SoM based on NXP i.MX8M Mini from Engicam.
i.Core MX8M Mini needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Mini EDIMM2.2 Starter Kit.
Linux dts commit details:
commit <051c08eea682> ("arm64: dts: imx8mm: Add Engicam i.Core MX8M Mini
EDIMM2.2 Starter Kit")
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This patch adds the dtsi/dts files needed to support the Marvell
Octeon TX2 CN9130 CRB. This is only the base port with not all
interfaces supported fully.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the i.MX6SX based UDOO Neo dts files from Linux 5.12-rc1
and sync the i.MX6SX pinfunc.h
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The SELI8 design is a new tdm service unit card for Hitachi-Powergrids
XMC and FOX product lines.
It is based on NXP LS1021 SoC and it provides following interfaces:
- IFC interface for NOR, NAND and external FPGA's
- 1 x RGMII ETH for debug purposes
- 2 x SGMII ETH for management communication via back-plane
- 1 x uQE HDLC for management communication via back-plane
- 1 x I2C for peripheral devices
- 1 x SPI for peripheral devices
- 1 x UART for debug logging
It is foreseen that the design will be later re-used for another XMC and
FOX service cards with similar SoC requirements.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Matteo Ghidoni <matteo.ghidoni@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
It's an old bringup board with out upstream Linux or L4T support
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add Engicam i.Core STM32MP1 SoM
Add FIP header support for STM32programmer
Update uart number when no serial device found for STM32MP1
Remove board_check_usb_power function when ADC flag is not set
Update SPL size limitation for STM32MP1
Set soc_type, soc_pkg, soc_rev env variables for STM32MP1
-----BEGIN PGP SIGNATURE-----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=4VxR
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210409' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add rt-thread art-pi board support based on STM32H750 SoC
Add Engicam i.Core STM32MP1 SoM
Add FIP header support for STM32programmer
Update uart number when no serial device found for STM32MP1
Remove board_check_usb_power function when ADC flag is not set
Update SPL size limitation for STM32MP1
Set soc_type, soc_pkg, soc_rev env variables for STM32MP1
7" OF is a capacitive touch 7" Open Frame panel solutions with
- 7" AUO B101AW03 LVDS panel
- EDT, FT5526 Touch
MicroGEA STM32MP1 is a STM32MP157A based Micro SoM.
MicroDev 2.0 is a general purpose miniature carrier board with CAN,
LTE and LVDS panel interfaces.
MicroGEA STM32MP1 needs to mount on top of MicroDev 2.0 board with
pluged 7" OF for creating complete MicroGEA STM32MP1 MicroDev 2.0
7" Open Frame Solution board.
Linux dts commit details:
commit <1d278204cbaa> ("ARM: dts: stm32: Add Engicam MicroGEA STM32MP1
MicroDev 2.0 7" OF")
Add support for it.
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
MicroDev 2.0 is a general purpose miniature carrier board with CAN,
LTE and LVDS panel interfaces.
Genaral features:
- Ethernet 10/100
- USB Type A
- Audio Out
- microSD
- LVDS panel connector
- Wifi/BT (option)
- UMTS LTE with sim connector (option)
MicroGEA STM32MP1 is a STM32MP157A based Micro SoM.
MicroGEA STM32MP1 needs to mount on top of this MicroDev 2.0 board
for creating complete MicroGEA STM32MP1 MicroDev 2.0 Carrier board.
Linux dts commit details:
commit <f838dae7afd0> ("ARM: dts: stm32: Add Engicam MicroGEA STM32MP1
MicroDev 2.0 board")
Add support for it.
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Engicam C.TOUCH 2.0 is an EDIMM compliant general purpose Carrier
board.
Genaral features:
- Ethernet 10/100
- Wifi/BT
- USB Type A/OTG
- Audio Out
- CAN
- LVDS panel connector
i.Core STM32MP1 is an EDIMM SoM based on STM32MP157A from Engicam.
i.Core STM32MP1 needs to mount on top of this Carrier board for
creating complete i.Core STM32MP1 C.TOUCH 2.0 board.
Linux dts commit details:
commit <6ca2898df59f> ("ARM: dts: stm32: Add Engicam i.Core STM32MP1
C.TOUCH 2.0")
Add support for it.
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Engicam EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board.
Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Mini PCIe
- MIPI CSI
- 2x CAN
- Audio Out
i.Core STM32MP1 is an EDIMM SoM based on STM32MP157A from Engicam.
i.Core STM32MP1 needs to mount on top of this Evaluation board for
creating complete i.Core STM32MP1 EDIMM2.2 Starter Kit.
Linux dts commit details:
commit <adc0496104b6> ("ARM: dts: stm32: Add Engicam i.Core STM32MP1
EDIMM2.2 Starter Kit")
Add support for it.
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This patchset has following changes:
- introduce stm32h750.dtsi to support stm32h750 value line
- add pin groups for usart3/uart4/spi1/sdmmc2
- add stm32h750i-art-pi.dtb (arch/arm/boot/dts/Makefile)
- add stm32h750i-art-pi.dts to support art-pi board
- add stm32h750i-art-pi-u-boot.dtsi to support art-pi board (u-boot)
art-pi board component:
- 8MiB qspi flash
- 16MiB spi flash
- 32MiB sdram
- ap6212 wifi&bt&fm
the detail board information can be found at:
https://art-pi.gitee.io/website/
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the dts file for the Olimex Olinuxino from the linux kernel, and enable
its use in this machine's defconfig.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Import the iMX6 based marsboard and riotboard. dts files from Linux 5.12-rc1
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Import the iMX53 based usbarmory dts files from Linux 5.12-rc1
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Andrej Rosano <andrej@inversepath.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add support for iMX8MN LPDDR4 EVK board which uses 2GB LPDDR4 and
PCA9450B PMIC.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add initial support for NanoPi M4B, a minor revision of
the original NanoPi M4.
Commit details of rk3399-nanopi-m4b.dts sync from Linux 5.12-rc4:
"arm64: dts: rockchip: Add NanoPi M4B board"
(sha1: c7b03115003f7f337ab165542cee37148cf30a8a)
Signed-off-by: Alexandre Vicenzi <alexandre.vicenzi@suse.com>
Reviewed-by: Kever Yang <kever.yang@rock-cihps.com>
NanoPi R4s is SBC base on Rockchip RK3399 hexa-core processor with
dual-Core Cortex-A72 and Mali-T864 GPU with 4GiB(LPDDR4) of RAM, SD card support,
including 2 gigabit ethernet(RTL8211E 1Gbps - RTL8111H 1Gbps) and 2 USB 3.0 port.
port.It also has two GPIO headers which allows further peripherals to be used.
The devicetree file is taken of the rk3399 nanopi4 Linux kernel [1].
[1] e7a0959082
Signed-off-by: xiaobo <peterwillcn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This brings the actual rk3368-lion devicetree files from Linux 5.10
instead of using something separate.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The EK874 development kit from Silicon Linux is made of CAT874 (the main
board) and CAT875 (the sub board that goes on top of CAT874).
This patch adds the required board support to boot Si-Linux EK874 board
based on R8A774C0 SoC.
DTS files apart from r8a774c0-ek874-u-boot.dts and r8a774c0-u-boot.dtsi
have been imported from Linux kernel 5.11 commit f40ddce88593
("Linux 5.11").
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
The HiHope RZ/G2H board from HopeRun consists of main board
(HopeRun HiHope RZ/G2H main board) and sub board(HopeRun
HiHope RZ/G2H sub board). The HiHope RZ/G2H sub board sits
below the HiHope RZ/G2H main board.
This patch adds the required board support to boot HopeRun HiHope
RZ/G2H board.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
The HiHope RZ/G2N board from HopeRun consists of main board
(HopeRun HiHope RZ/G2N main board) and sub board(HopeRun
HiHope RZ/G2N sub board). The HiHope RZ/G2N sub board sits
below the HiHope RZ/G2N main board.
This patch adds the required board support to boot HopeRun HiHope
RZ/G2N board.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
The HiHope RZ/G2M board from HopeRun consists of main board
(HopeRun HiHope RZ/G2M main board) and sub board(HopeRun
HiHope RZ/G2M sub board). The HiHope RZ/G2M sub board sits
below the HiHope RZ/G2M main board.
This patch adds the required board support to boot HopeRun HiHope
RZ/G2M board.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Make the conversion to driver model as it is mandatory.
Successfully tested booting Linux from the SD card.
Dropped splash screen support as this needs to be properly
converted to DM and tested.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Make the conversion to driver model as it is mandatory.
Tested booting the Linux kernel from the SD card.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Make the conversion to driver model as it is mandatory.
Remove the SATA support for now as the i.MX53 support has not
been added yet.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
This board has not been converted to CONFIG_DM_MMC by the deadline of
v2019.04, which is almost two years ago. In addition there are other DM
migrations it is also missing. Remove it.
Cc: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Chris Packham <judge.packham@gmail.com>
Although this variant has two external network ports, they are not (yet)
supported by the bootloader because they are connected via an internal
network switch. Otherwise its the same as the other variants.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This variant has one network port connected via RGMII and doesn't have
any TSN capabilities out-of-the-box. Instead it has all four SerDes
lanes available for customer use.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The Beacon EmbeddedWorks kit is based on the R8A774E1 SoC also
known as the RZ/G2H.
The kit consists of a SOM + Baseboard and supports microSD,
eMMC, Ethernet, a couple celular radios, two CAN interfaces,
Bluetooth and WiFi. It shares much of the same design as
the RZ/G2M and RZ/G2N dev kits.
Signed-off-by: Adam Ford <aford173@gmail.com>
The Beacon EmbeddedWorks kit is based on the R8A774B1 SoC also
known as the RZ/G2N.
The kit consists of a SOM + Baseboard and supports microSD,
eMMC, Ethernet, a couple celular radios, two CAN interfaces,
Bluetooth and WiFi. It shares much of the same design as
the RZ/G2M dev kit.
Signed-off-by: Adam Ford <aford173@gmail.com>
OrangePi Zero2 is SBC based on Allwinner H616 with 1 GiB of RAM, SD card
support, gigabit ethernet, micro HDMI, WIFI, Bluetooth and 1 USB 2.0
port. It also has two GPIO headers which allows further peripherals to
be used.
The devicetree file is taken from v3 of the OrangePi Zero2 Linux
submission [1], which it's not yet merged.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2021-January/632084.html
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
dts file is taken from Linux 5.11-rc1 tag.
The Bluetooth controller of this device ships with a default address,
use the new CONFIG_FIXUP_BDADDR option to fix it up.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
[Updated OrangePi 3 DT, rebase and config update]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This commit adds support for Tanix TX6 TV box, based on H6. It's low end
H6 board, with 3 GiB of RAM, eMMC, fast ethernet, USB, IR and other
peripherals.
DT file is taken from Linux 5.11-rc1 release.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmAOkP8cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKedCACiDHgP71VKSOiYnEU4
vHD/ANmfMXqnsL71PpSdagnBRAl4vpm46CnD+Mq7RtchxGDNufX6tWJSI04Ci0bC
mfmIfVEjePOnuUayylJ55OlrtJVpBqJFPqxM6MFcIF7nRja1r5thV1jTLNu+b4sm
gg2sk1mC/531Lxbk8S7x+diPymNRArEm3IEw+xEqUhsNVQCKjOEcxi/BWIB2prR3
NxRSGdW3j4CKdBqt7uOL1bqApeQQ9m0/gm1tE3hMXUo09I7uXmb7U52aKb5cV8L+
8ZOlbav6yaPACe3p9npp4K0ByXMmYHjeo1NZW4cvAoKfzragdu0Cv7f0ssVCgrlR
p1e3
=xS6A
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.04-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.04 cycle
This feature set includes macb updates for all interfaces and new
sama7g5 variant support; micrel ksz9031 DLL support; a new board from
Giant based on Adafruit feather form factor which contains a SAMA5D27
SoC; several fixes regarding the NAND flash PMECC block; and pincontrol
drive strength support for pio4 controller.
Beacon EmbeddedWorks is releasing a devkit based on the i.MX8M
Nano SoC consisting of baseboard + SOM.
The kit is based on the same design as the Beacon dev kit with
the i.MX8M Mini.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Giant board is a tiny SBC based on the Adafruit Feather form factor,
created by groboards it contains a SAMA5D2 processor (SAMA5D27),
128 MB of RAM and a microSD card for storage.
Signed-off-by: Greg Gallagher <greg@embeddedgreg.com>
This adds support for the NanoPi R2S from FriendlyArm.
Rockchip RK3328 SoC
1GB DDR4 RAM
Gigabit Ethernet (WAN)
Gigabit Ethernet (USB3) (LAN)
USB 2.0 Host Port
MicroSD slot
Reset button
WAN - LAN - SYS LED
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
AST2600 is the 7th generation of Aspeed SoC designated for
Interated Remote Management Processor.
AST2600 has significant performance improvement by integrating
1.2GHz dual-core ARM Cortex A7 (r0p5) CPU with FPU. Most of the
controllers are also improved with more features and better
performance than preceding AST24xx/AST25xx.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl/8S/0cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKFkB/9NBJq/+sgHZXRaMlAu
ULNwOPoNsQxHQGwF88B1lC+H8LJjM+2gJ8MfJdWvHNlcSdtJjbWk0aQL+5LKSlyz
G7l3BZ+AIYMOeTXay5mNUKnekXIr7c8tLoX8FH/Ih+bHFPt57qL0bbfznV66UCOp
/o/yM8daPa9Kx1vPEpT2dC9bYXLXeQv6R+RMxwoc4Bk+R3OK7zoZ3Wdx0q9HvBwj
iWHM49X2fBqqi5RS+ZI37AUzi8iysD3fOq0kWTJcCNaci8i8RZdzSyoaDuXhA63I
EZJ7v9fUkW/bwTONVE9n2BX4xF9X/6R7P46l9dQISXAxsOBwsNRQPt8Ro7mCoc4K
392o
=LIK7
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.04-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features for 2021.04 cycle
This feature set includes the new board SAMA7G5 EK, the new evaluation
kit for Microchip AT91 SAMA7G5 SoC . The current board support includes
two configurations for booting from eMMC (SDMMC0), SD-Card (SDMMC1), and
support for two Ethernet interfaces.
PineCube is an IP camera development kit released by Pine64.
It comes with the following compoents:
- A mainboard with Sochip S3 SoC, a 16MByte SPI Flash, AXP209 PMIC,
a power-only microUSB connector, a USB Type-A connector, a 10/100Mbps
Ethernet port and FPC connectors for camera and daughter board.
- An OV5640-based camera module which is connected to the parallel CSI
bus of the mainboard.
- A daughterboard with several buttons, a SD slot, some IR LEDs, a
microphone and a speaker connector.
As the device tree is synchronized in a previous commit, just add it to
Makefile, create a new MAINTAINER item and provide a defconfig.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Import the Beelink GT-King/Pro and supporting meson-g12b-w400.dtsi file
from Linux 5.10.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Import the WeTek Core2 and supporting meson-gx-p23x-q20x.dtsi files
from Linux 5.10.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Sync the libretech cc v2 device tree from Linux v5.10-rc1
commit 3650b228f83a ("Linux 5.10-rc1")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Introduce initial hierarchy of device trees for Apalis iMX8X
System on Module.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Removed aristainetos2, 2b, 2b-csl. This boards have been
recalled and destroyed.
Adapt board code to remove stuff not needed anymore.
Fix checkpatch warning, remove fdt_high and initrd_high
from default environment.
Signed-off-by: Heiko Schocher <hs@denx.de>
zu remove
Add DT for DH PicoITX unit, which is a bare-bones carrier board for
the DHCOM. The board has ethernet port, USB, CAN, LEDs and a custom
board-to-board expansion connector.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Import updated device trees from Linux tag v5.9. This picks up new
hardware (PinePhone, PineTab); and it drops the U-Boot specific DTSI
files for the Pinebook and the Teres-I, since the ANX6345 bridge is
now supported upstream.
A couple of headers needed updates for recently-added hardware support.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
GE B1x5v2 patient monitor series is similar to the CARESCAPE Monitor
series (GE Bx50). It consists of a carrier PCB used in combination
with a Congatec QMX6 SoM. This adds U-Boot support using device model
everywhere and SPL for memory initialization.
Proper configuration is provided as 'ge_b1x5v2_defconfig' and the
combined image u-boot-with-spi.imx can be flashed directly to 1024
byte offset to /dev/mtdblock0. Alternatively SPL and u-boot.imx can
be loaded separately via USB-OTG using e.g. imx_usb.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
- New PX30 board: Engicam PX30.Core;
- Fix USB HID support for rock960;
- Remove host endianness dependency for rockchip mkimage;
- dts update for rk3288-tinker;
- Enable console MUX for some ROCKPi boards;
- Add config-based ddr selection for px30;
PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
C.TOUCH 2.0 is a general purpose carrier board with capacitive
touch interface support.
PX30.Core needs to mount on top of this Carrier board for creating
complete PX30.Core C.TOUCH 2.0 board.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board from Engicam.
PX30.Core needs to mount on top of this Evaluation board for
creating complete PX30.Core EDIMM2.2 Starter Kit.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
common:
- Add support for 64bit loadables from SPL
xilinx:
- Update documentation and record ownership
- Enable eeprom board detection based legacy and fru formats
- Add support for FRU format
microblaze:
- Optimize low level ASM code
- Enable SPI/I2C
- Enable distro boot
zynq:
- Add support for Zturn V5
zynqmp:
- Improve silicon detection code
- Enable several kconfig options
- Align DT with the latest state
- Enabling security commands
- Enable and support FPGA loading from SPL
- Optimize xilinx_pm_request() calling
versal:
- Some DTs/Kconfig/defconfig alignments
- Add binding header for clock and power
zynq-sdhci:
- Add support for tap delay programming
zynq-spi/zynq-qspi:
- Use clock framework for getting clocks
xilinx-spi:
- Fix some code issues (unused variables)
serial:
- Check return value from clock functions in pl01x
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX5rH/QAKCRDKSWXLKUoM
IRPAAJ9SvHR3w1qTc5W+Q5CWBUH5wJbNYQCaA4PpqZCdvyu1+nF5luL6JHhbDgw=
=hOd7
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01-v2' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.01-v2
common:
- Add support for 64bit loadables from SPL
xilinx:
- Update documentation and record ownership
- Enable eeprom board detection based legacy and fru formats
- Add support for FRU format
microblaze:
- Optimize low level ASM code
- Enable SPI/I2C
- Enable distro boot
zynq:
- Add support for Zturn V5
zynqmp:
- Improve silicon detection code
- Enable several kconfig options
- Align DT with the latest state
- Enabling security commands
- Enable and support FPGA loading from SPL
- Optimize xilinx_pm_request() calling
versal:
- Some DTs/Kconfig/defconfig alignments
- Add binding header for clock and power
zynq-sdhci:
- Add support for tap delay programming
zynq-spi/zynq-qspi:
- Use clock framework for getting clocks
xilinx-spi:
- Fix some code issues (unused variables)
serial:
- Check return value from clock functions in pl01x
Adding Z-turn board V5 to resolve the change between:
"Z-TURNBOARD_schematic.pdf" schematics state version 1 to 4 has Atheros AR8035
"Z-Turn_Board_sch_V15_20160303.pdf" schematics state version 5 has Micrel KSZ9031
At this time the S25FL128SAGNFI003 doesn't work because of bug:
*** Warning - spi_flash_probe_bus_cs() failed, using default environment
zynq-zturn was checked on V5 board, same error.
Maybe Z-turn board have the same problem (board with W25Q128BVFIG).
Signed-off-by: Alexandre GRIVEAUX <agriveaux@deutnet.info>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add basic support for the Kontron SMARC-sAL28 board. This includes just
the bare minimum to be able to bring up the board and boot linux.
For now, the Single and Dual PHY variant is supported. Other variants
will fall back to the basic variant.
In particular, there is no watchdog support for now. This means that you
have to disable the default watchdog, otherwise you'll end up in the
recovery bootloader. See the board README for details.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Import armada-3720-espressobin-emmc.dts from Linux, but use sdhc1 for
emmc, since our dtsi is still based on downstream and sdhc0 is used for
the sd card.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Add initial U-Boot support for the iEi Puzzle-M801 board based on the
Marvell Armada 88F8040 SoC.
Currently supported hardware:
1x USB 3.0
4x Gigabit Ethernet
2x SFP+ (with NXP PCA9555 and NXP PCA9544)
1x SATA 3.0
1x M.2 type B
1x RJ45 UART
1x SPI flash
1x EPSON RX8010 RTC
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
