The card detect pin was incorrectly using IRQ_TYPE_LEVEL_LOW
instead of GPIO_ACTIVE_LOW when reading the state of the CD pin.
Without this patch, MMC1 won't be detected.
This is the same patch submitted to linux-omap, but I was hoping
to get it applied to U-Boot without having to wait for the
linux adoption and then backporting.
Fixes: 5448ff33f2 ("ARM: DTS: Resync Logic PD SOM-LV 37xx
devkit with Linux 4.18-RC4")
Signed-off-by: Adam Ford <aford173@gmail.com>
Add device-tree files from linux 5.1-rc7 needed to complete support
for PocketBeagle.
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Transition to the IOPAD macros as used in Linux in which the pin mux
mode is specified using a dedicated parameter while also dropping the
related MUX_MODEx macros that are no longer needed. This transition
will allow us to keep both Linux and U-Boot DTS in sync more easily.
While at it also align the file name of the include file itself and
update any references accordingly.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
- at91sam9g20-taurus.dts: use labels
- cleanup taurus port to compile clean with
current mainline again. SPL has no serial
output anymore, so it fits into SRAM.
Signed-off-by: Heiko Schocher <hs@denx.de>
Switch from using the high priority DMSC transmit message queue used
by the secure R5 MCU island boot context to the low priority message
queue. While the change in priority is irrelevant for the current boot
architecture it however gives us access to a deeper message queue that
will allow us to buffer more messages. This is an important aspect when
sending several messages without requesting and waiting for a response
in a row which is a communication scheme used during core shutdown for
example. See AM654 TISCI User Guide for additional details.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
------------------------
- warp7 to DM
- kp_imx53 to DM
- Warnings in DT
- MX8QM support
- colibri-imx6ull to DM
- imx7d-pico to DM
- ocotp for MX8
-----BEGIN PGP SIGNATURE-----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=CzWQ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20190426' of git://git.denx.de/u-boot-imx
Porting to DM and i.MX8
------------------------
- warp7 to DM
- kp_imx53 to DM
- Warnings in DT
- MX8QM support
- colibri-imx6ull to DM
- imx7d-pico to DM
- ocotp for MX8
u-boot,dm-pre-reloc is required for SDMMC booted rk3399 boards and
which is U-Boot specific devicetrees binding.
Move it on global rk3399-u-boot.dtsi file and rest of the U-Boot
bindings will move it future based on the requirement.
This would help to sync the devicetrees from Linux whenever required
instead of adding specific nodes.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Sync rk3399-opp.dtsi from Linux.
Linux commit details about the rk3399-opp.dtsi sync:
"arm64: dts: rockchip: use SPDX-License-Identifier"
(sha1: 4ee99cebd486238ac433da823b95cc5f8d8a6905)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Booting this board failed as the initial console isn't found since
commit c402e81702 ("dts: arm: socfpga: merge gen5 devicetrees from linux")
The uart0 devicetree entry was missing "clock-frequency = <100000000>:"
since that commit
Fixes: c402e81702 ("dts: arm: socfpga: merge gen5 devicetrees from linux")
Reported-by: rafael mello <rafaelmello_3@hotmail.com>
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Add the device trees for
* vexpress_ca5x2_defconfig
* vexpress_ca9x4_defconfig
* vexpress_ca15_tc2_defconfig
as available in Linux 5.1 rc5.
We are using the vexpress_ca15_tc2_defconfig and vexpress_ca9x4_defconfig
for Travis testing via QEMU.
The UEFI base Embedded Base Boot Requirements Specification (EBBR) requires
that an embedded board either provides a device tree or an ACPI table.
All block devices are meant to be moved to the driver model. On ARM this
requires a device tree.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is Marvell's Kirkwood development board. It has the following
features
- 512M DDR2
- 2 PCI connectors
- 1 x1 PCI-e interface
- 1 Gigabit Ethernet Port
- 2 SATA Ports
- USB 2.0 Interface
- SDIO
- 128M NAND Flash
- 16M SPI Flash
It can be strapped to boot from SPI or NAND so there are two defconfigs
(one per boot media).
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The following Kirkwood dtb build targets are currently missing:
kirkwood-openrd-base.dtb
kirkwood-openrd-client.dtb
kirkwood-openrd-ultimate.dtb
This patch adds them to the Makefile to fix the build error.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This commit switches to DM USB for warp7 and warp7_bl33 defconfigs.
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This commit switches to DM SERIAL for warp7 and warp7_bl33 defconfigs.
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Fix compatible node to use regular Toradex notation.
Annotate device tree with standard Colibri pin muxing comments.
Use open-drain I2C pin muxings.
Alphabetically re-order iomuxc nodes.
Rename snvs-ad7879-int-grp touch interrupt node as per Linux device tree.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Add GPIO1_IO03__OSC32K_32K_OUT pin muxing.
While at it also fix indentation of pinfunc header file.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This patch enable convert DM MMC for imx7d-pico board and variant.
Before the DM conversion only usdhc3 was enabled and therefore it appeared
as MMC 0 to u-boot. After enabling MMC DM though usdhc3 defaults to MMC 2,
which left unattended would drive changes to existing pico-pi bootscripts and
environment variables that rely on mmc 0.
Setup the alias of mmc0 and usdhc3 so that existing pico-imx7d boot code will
work unmodified.
When converting to DM_MMC it is necessary that SPL initializes eMMC
by itself, so move the original eMMC initialization from U-Boot
proper to SPL.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Add support for lpuart1, lpuart2 and lpuart3.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This patch imports the Linux kernel base board imx7d-pico.dtsi,
pi board imx7d-pico-pi.dts and hobbit board imx7d-pico-hobbit.dts
from Linux v5.1-rc1.
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Migrate Ethernet FEC to using driver model.
Drop PHY_MICREL_KSZ90X1 which slipped in from Apalis iMX6.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Migrate USB to using driver model.
Add USBH_PEN GPIO regulator.
While at it also add alias e.g. as required for UMS.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Migrate MMC to using driver model.
Migrate USDHC to using pinctrl.
While at it also add GPIO1_IO03__OSC32K_32K_OUT pin muxing.
While at it also update copyright period.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
The implicit fallback mechanism for searching the whole MDIO bus for at
least one PHY has been gone with the following commit b882005a18
("drivers/net/fec: phy_init: remove redundant logic"). This lead to the
Ethernet driver erroring out as follows:
Net: Could not get PHY for FEC0: addr -19
eth-1: fec@400d1000
Colibri VFxx # dhcp
Could not get PHY for FEC0: addr -19
Could not get PHY for FEC0: addr -19
Could not get PHY for FEC0: addr -19
Could not get PHY for FEC0: addr -19
No ethernet found.
Could not get PHY for FEC0: addr -19
Colibri VFxx #
This commit adds an explicit PHY node which makes it work again.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This commit enables the support for K&P's HSC|DDC imx53 based boards.
It was also necessary to provide device tree description for regulators
to avoid board specific code definition.
The GPIO pin description responsible for VBUS control has been moved from
"hog" group to usbh1 dedicated one.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This code has been ported from Linux kernel - tag v5.1-rc2.
The difference from the kernel is the removal of:
fsl,usbmisc = <&usbmisc 1>;
fsl,usbphy = <&usbphy1>;
properties, which are not needed for correct u-boot operation (as PHY
setup is done in ehci-mx5.c file itself).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
In this commit the esdhc3 controller is enabled as well as it is remaped
to mmc0 to not break legacy code.
The pinctrl setup (e.g. 0x1e4) is the same as one from in-board file
definition.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
with u-boot,dm-spl added for imx8qx-pm node, and SPL_SIMPLE_BUS enabled,
the bind and probe code in board file could be removed.
Also we need to enlarge SYS_MALLOC_F_LEN to avoid calloc fail.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add support for MediaTek MT8516 SoC. This include the file
that will initialize the SoC after boot and its device tree.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The 'phy' reset of gmac device in kernel device tree is not generic
enough for u-boot to use, so we need to overwrite the 'resets' property
as needed. With this device tree fixup and poplar_defconfig changes,
Ethernet starts working on Poplar board.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
As U-boot stm32f clock driver doesn't support new
bindings for auxiliary clocks (clocks = <&rcc 1 ....>),
restore old bindings for usart1 to get console output.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Synchronize stm32h7 device tree with kernel v4.20.
U-boot DT files and pinctrl bindings are updated,
useless nodes are removed and gpio compatible added.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In order to prepare and ease future DT synchronization with kernel
DT, migrate all U-boot specific nodes/properties/addons to
U-boot DT files.
As sdmmc is not yet supported on kernel side, sdmmc nodes
are located in eval-u-boot and disco-u-boot DT files.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In order to prepare and ease future DT synchronization with kernel
DT, migrate all U-boot specific nodes/properties/addons to
U-boot DT files.
Migrate also DT nodes which are not yet available on kernel DT side
as ethernet, ltdc and qspi nodes.
Fix ethernet_mii pins and add missing qspi_pins for stm32746g-eval
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Import Linux 5.1-rc1 DT from 9e98c678c2d6 ("Linux 5.1-rc1") for the
meson-g12a-u200 board, the meson-g12a.dtsi and the corresponding bindings.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcvW07AAoJEB6zHgIOrC/Iu4QH/1REDOTrsZPydd2yD/O81vPs
RiLC8wP2J4UmqtMcNTLyvxlYwrzqoR5J6SYdyBNU/+cLEp/gdzEI+rjsfSV2uRX1
Qb4Pk2FiI503JVjegxsbJqzASfiEP7rIg3HM5431xbhYH22MW2FH6le6yrtNxjBh
m1WFjQYX1bpbGb6zue8TgyLIeN1IqWuqnH9kUHixUEan+xrpEhN239LDFjdvGbvC
BvYyMtDddmMt4YDzNjgX36us993kylGZp6JijR3zgUao7I/JGVZAJrxw8MHDTnVy
UKv3VI9F5bGLSvzqTVL2MFU6XtJW26v+niGLhGzlUhb3TTKrdKOicm3VF7tO+JU=
=MamK
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2019.07-b' of git://git.denx.de/u-boot-atmel
Second set of u-boot-atmel features and fixes for 2019.07 cycle
The DK1 and DK2 boards use the USB Type-C controller STUSB1600.
This patch updates:
- the device tree to add the I2C node in the DT
- the board stm32mp1 to probe this I2C device and use this controller
to check cable detection.
- the DWC2 driver to support a new dt property
"u-boot,force-b-session-valid" which forces B session and
device mode; it is a workaround because the VBUS sensing and
ID detection isn't available with stusb1600.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Use the DWC2 device driver with DM_USB_GADGET support and
cleanup the USB support in STM32MP1 board.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- 16GB eMMC
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- USB 2.0 and 3.0 Host
- HDMI port
- S/PDIF port
- 5V/2A DC power supply
- Wi-Fi/BT via Fn-Link 6222B-SRB (RTL8222BS)
Linux commit details about the sun50i-h6-beelink-gs1.dts sync:
"arm64: dts: allwinner: h6: Introduce Beelink GS1 board"
(sha1: 089bee8dd119ba084dee6b17a2e1a53df4f30193)
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The SAMA5D2 ICP Board features the SAMA5D27 SoC,
together with QSPI Flash, Wilc3000 wireless device and
EtherCat support.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Merge qspi dts node from Linux.
Commit 0cb140d07fc75fb (arm64: dts: stratix10: Add QSPI support for Stratix10)
Add -u-boot.dtsi files for non Linux dts properties and
update properties for Uboot.
- add u-boot,dm-pre-reloc
- add alias for spi0
- change compatible for flash
- support quad read and quad write
- change maximum frequency to 100MHz
Tested on Stratix 10 SoC devkit.
SOCFPGA_STRATIX10 # sf probe 0:0
SF: Detected mt25qu02g with page size 256 Bytes, erase size 64 KiB, total 256 MiB
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
The stratix10 socdk ships with 4GB of memory. Modify the
device tree to represent this. Note that to access 4GB of
memory in Stratix 10, due to the IO space from 2GB to 4GB,
we use the fact that the DDR controller ignores upper address
bits outside of the configured DRAM's size. This means that
, the 4GB DRAM is mapped to memory every 4GB.
For an 8GB memory, you can either live with the 2GB IO space,
and loose access to that memory from the processor, or use
the same trick:
Loose 2GB of memory:
memory {
device_type = "memory";
/* 8GB */
/* first 2GB */
reg = <0 0x00000000 0 0x80000000>,
/* last 4GB */
<1 0x00000000 1 0x00000000>;
u-boot,dm-pre-reloc;
};
or to map it all:
memory {
device_type = "memory";
/* 8GB */
/* first 2GB */
reg = <0 0x00000000 0 0x80000000>,
/* next 6GB */
<2 0x80000000 1 0x80000000>;
u-boot,dm-pre-reloc;
};
Signed-off-by: Dalon Westergreen <dalon.westergreen@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
To clean up reset handling for socfpga gen5, port the DDR driver to DM
using UCLASS_RAM and implement proper reset handling.
This gets us rid of one ad-hoc call to socfpga_per_reset().
The gen5 driver is implemented in 2 distinct files. One of it (containing
the calibration training) is not touched much and is kept at using
hard coded addresses since the code grows even more otherwise.
SPL is changed from calling hard into the DDR driver code to just
probing UCLASS_RESET and UCLASS_RAM. It is happy after finding a RAM
driver after that.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
The SPL for socfpga gen5 currently takes all peripherals out of reset
unconditionally. To implement proper reset handling for peripherals,
the reset node has to be provided with the SPL dts.
In preparation to move the DDR driver to DM, the sdr node is required
in SPL, too.
This patch adds "u-boot,dm-pre-reloc" to U-Boot specific dtsi addon
files so that the reset manager and SDR driver correctly probe in SPL.
It centralizes these settings into a common file since in contrast to
boot-type specific nodes, "soc", "rst" and "sdr" are always needed.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This is again a sync to linux-next + pending patches in Dinh's tree at
commit 1c909b2dfe6a ("ARM: dts: socfpga: update more missing reset
properties")'
It adds missing peripheral reset properties to socfpga.dtsi and removes
U-Boot specific leftovers from socfpga_cyclone5_socrates.dts.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
fpga:
- Add support for external data in FIT
- Extend testing for external data case
- Inform user about a need to run post config on Zynq
arm:
- Tune zynq command functions
- Fix internal variable setting
arm64:
- Add support for zc39dr decoding
- Disable WDT for zcu100
- Small changes in reset_reason()
- Some DT changes (spi)
- Tune qspi-mini configuration
- Remove useless eeprom setting
- Fix two sdhci boot case
spi:
- Fix tap delay programming
clk:
- Enable i2c in SPL
net:
- Fix gem phydev handling
- Remove phy detection code from gem driver
general:
- Correct EXT_DTB usage for MULTI_DTB_FIT configuration
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAly262oACgkQykllyylKDCH44gCbBnuxUH6ZF0B7Leuee4te7C59
LmUAn14/bbtMt17zkMSADCjY9yGWF4au
=mWrW
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2019.07' of git://git.denx.de/u-boot-microblaze
Xilinx/FPGA changes for v2019.07
fpga:
- Add support for external data in FIT
- Extend testing for external data case
- Inform user about a need to run post config on Zynq
arm:
- Tune zynq command functions
- Fix internal variable setting
arm64:
- Add support for zc39dr decoding
- Disable WDT for zcu100
- Small changes in reset_reason()
- Some DT changes (spi)
- Tune qspi-mini configuration
- Remove useless eeprom setting
- Fix two sdhci boot case
spi:
- Fix tap delay programming
clk:
- Enable i2c in SPL
net:
- Fix gem phydev handling
- Remove phy detection code from gem driver
general:
- Correct EXT_DTB usage for MULTI_DTB_FIT configuration
Enable ahci node for BPI-M2-Berry, this would require since
we have DM_SCSI enabled on the respective SoC.
Unable to sync the same node from Linux, since the similar change
is still in Linux ML.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable ahci node for a20-wits-pro-a20-dkt, this would require since
we have DM_SCSI enabled on the respective SoC.
Right now, ahci enabled in -u-boot.dtsi and will remove once same
supported by Linux.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable ahci node for sun7i-a20-m5.dts, this would require since
we have DM_SCSI enabled on the respective SoC.
No need to send patch to Linux for this change, since this
dts is U-Boot specific.
Cc: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Sync sun7i-a20 dts(i) files from Linux 5.1-rc2
Linux commit details about the sun7i-a20* sync:
"ARM: dts: sun7i: bananapi: Add GPIO banks regulators"
(sha1: 09c6572290f018d73ec2e812e28bada34d41815f)
Here are U-Boot specific dts changes.
- s/uart0_pins_a/uart0_pb_pins for
sun7i-a20-ainol-aw1.dts
sun7i-a20-m5.dts
sun7i-a20-primo73.dts
sun7i-a20-yones-toptech-bd1078.dts
sunxi-itead-core-common.dtsi
- s/gmac_pins_mii_a/gmac_rgmii_pins for
sun7i-a20-m5.dts
- drop i2c0, i2c1 pins from
sunxi-itead-core-common.dtsi
- drop mmc0 pins from
sun7i-a20-primo73.dts
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Sync sun8i-r40 dts(i) files from Linux 5.1-rc2
Linux commit details about the sun8i-r40* sync:
"ARM: dts: sun8i: r40: bananapi-m2-ultra: Add Bluetooth device node"
(sha1: 1e5f1db4ccd8348a21da55bff82f4263000879ef)
Linux commit details about the sun8i-v40* sync:
"ARM: dts: sunxi: Fix I2C bus warnings"
(sha1: 0729b4af5753b65aa031f58c435da53dbbf56d19)
Cc: Pablo Sebastián Greco <pgreco@centosproject.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Define a label for flash node so that it can be
referenced easily as required.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
spi-flash compatible string is needed for reading tx and rx bus
widths, hence add this compatible string to flash node.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
add labels to rtc, pinctrl and watchdog node.
This makes it possible to reference the nodes
from board dts files.
Signed-off-by: Heiko Schocher <hs@denx.de>
-----------
- DM support in sata
- Toradex Board to DM
- wandboard to DM
- tbs2910 to DM
- GE boards to DM
- VHybrid boards to DM
- DM_VIDEO for i.MX
-----BEGIN PGP SIGNATURE-----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=KLsH
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20190415' of git://git.denx.de/u-boot-imx
Move to DM
-----------
- DM support in sata
- Toradex Board to DM
- wandboard to DM
- tbs2910 to DM
- GE boards to DM
- VHybrid boards to DM
- DM_VIDEO for i.MX
Usually the Linux dts changes were synced in specific tags in Allwinner,
to keep track for whats been synced so-far and plan for future syncs.
But this patch sync sun50i-h6* dts(i) files from Linux w/o any specific
tag since these dts(i) changes are required for new H6 boards support.
Linux commit details about the sun50i-h6* sync:
"arm64: dts: allwinner: h6: move MMC pinctrl to dtsi"
(sha1: 6ba2e45d57afdfd982d12f168edd6a79a65075d8)
Linux commit details about the sun8i-tcon-top.h sync:
"dt-bindings: display: sunxi-drm: Add TCON TOP description"
(sha1: 59a9c39544cd1e5952c2a33028d71aa8180648f8)
Part of the sync initiated by 'Clément Péron'.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Fix broken build:
Device Tree Source is not correctly specified.
Please define 'CONFIG_DEFAULT_DEVICE_TREE'
or build with 'DEVICE_TREE=<device_tree>' argument
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix broken build:
Device Tree Source is not correctly specified.
Please define 'CONFIG_DEFAULT_DEVICE_TREE'
or build with 'DEVICE_TREE=<device_tree>' argument
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Update device tree in preparation of further driver model migration:
Ethernet FEC, ESDHC aka MMC/SD card, I2C, NFC aka NAND flash controller,
USBH_PEN GPIO regulator.
Add iomux resp. pinctrl entries to be removed from proprietary platform
data: DSPI, ESDHC, FEC, I2C, NFC, UART, USBH_PEN GPIO.
Introduce a U-Boot specific device tree with some required
u-boot,dm-pre-reloc properties: soc, aips0, pinctrl_ddr and uart0 incl.
pinctrl.
While at it also update the MAINTAINERS file.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
... as preparation for additional driver model coonversions.
We use CONFIG_OF_EMBED here to keep u-boot.imx as final binary name. So we
maintain compatibility with the original TBS u-boot and available HOWTOs
for u-boot updates.
Signed-off-by: Soeren Moch <smoch@web.de>
This commit brings a separate file in which the U-Boot specific
properties (like 'dm-pre-reloc') are provided.
Such approach allows easy sync with upstream Linux kernel in the
future.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This commit provides update and renames the bk4r1.dts to vf610-bk4r1.dts
file with more on SoC HW description.
The pcm052.dts has been renamed to vf610-pcm052.dts as well.
Moreover, a new vf610-pcm052.drsi file has been introduced
to reuse the common code between devices based on Phytec's
pcm052 modules.
Ported from Linux kernel - v4.20 (tag)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch allows moving vf610 based boards to a device tree and model.
Ported from Linux kernel - v4.20 (tag)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This patch provides definitions necessary for VF610 DDR pad configurations.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
- ath79: small fixes, add support for QCA9563 SoC and AP152 reference board
- mscc: small fixes, add network support for JR2 and ServalT SoCs
- bmips: small fixes, enable more drivers for ARM specific BCM6858 and BCM63158 SoCs
- MIPS: fix redundant relocation of initrd images
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiQkHUH+J02LLC9InKPlOlyTyXBgFAlywtKQACgkQKPlOlyTy
XBgYbBAAlRLhN52f2vv9Hng/tfCAuZk7c9tJ+b/5i36ZoJNozeaiOBgwVl3eeEa9
v4SeKz4J+9FJLOSZkIPrCvX+HaACQn7Pqw/64h3JE8TEzfU5lgmV4Xk2dcXtkmEL
L5PTQoNMZDgQaeltLtN29yIW5lVxx0NUN9O0FLY5+R/ptXlCFaAGdgSuXH36boDR
/cvfLlaZPM/hA7l3wRUjWa17L8MNEon4+cqLkzDyTTihdHOdZA4P1O7ce/XffGQp
BAiSta4EztB1xs0oTAOEmUJp1v8Ae7yRuFoZaCp+Dgq+0WOTbxDW4J57fTaphES1
su3yoYjju+M/dUb/sWmOQNjeIchJPYWcpiOl9E8jQ/l2SaBJ6Oxmg7PxC3Ww0X2z
JdF6mcKeaDH3WYO20FeC6xb9Q9FN2yX4rcW/Yg46TdeJ3T2sj8A19ZCHoeAQRl0I
68SbAaDJw/K3fTBFPd9VyQQQawPbyhmpdQAOWtixNWBFIBbZpqI4o1DMJKJRoxqd
Ail++ysLUICB0XXg0rGI+dFusjcu9AAeRODc11dtGa0YBh2Y28JrJ4OuV14GYQhe
5J8BquRaDADA3iK/+3C6TUSQGhb5pFXTcsdNBC9zBPb/ePeMDfZxBcB2vCOnZDZ1
m0kR5qnsz4IH8/rCmJ5wmMBh6JuyPoCSdiTVuuU5CuCVGYbmJuE=
=NrV8
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2019-04-12' of git://git.denx.de/u-boot-mips
- mt76xx: add USB support, small fixes
- ath79: small fixes, add support for QCA9563 SoC and AP152 reference board
- mscc: small fixes, add network support for JR2 and ServalT SoCs
- bmips: small fixes, enable more drivers for ARM specific BCM6858 and BCM63158 SoCs
- MIPS: fix redundant relocation of initrd images
- Misc dts files sync'ed with Linux version (Chris)
- Orion watchdog fix (Chris)
- kwbimage changed to also support Marvell bin_hdr binary (Chris)
- Add DM support to enable CONFIG_BLK for sata_mv (Stefan)
- Enable BLK on multiple platforms (Stefan)
- Misc minor fixes to AXP theadorable board (Stefan)
- Correct logic for DM_SCSI + unconverted drivers check (stefan)
- Misc changes to kirkwood to enable DM_USB here (Chris)
- Change ahci_mvebu to enable usage on A38x (Baruch)
- Update the kirkwood entry in git-mailrc (Baruch)
- Misc minor improvements (turris, documentation) (Baruch)
- Enhance sata_mv to support Kirkwood as well (Michael)
- Add wdt command (Michael)
- Add Marvell integrated CPUs (MSYS) support with DB-XC3-24G4XG
board support (Chris)
Adds alias to set the pincontrol seq id.
For STMFX gpio expander, force sequence number after
the last bank (GPIOZ) to avoid conflict between STM32MP and STMFX
gpio bank sequence number.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add adc related nodes. These nodes are used to detect the
current supplied by USB type-C power in port on DK1 and DK2
boards.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This patch synchronizes U-boot DT with kernel one
This is based on https://patchwork.kernel.org/cover/10797115/
This patch adds initial support of STM32MP157 discovery boards:
- Add support of stm32mp157a discovery1 board (part number: STM32MP157A-DK1).
This board embeds a STM32MP157a SOC with AC package (TFBGA361, 148 ios)
and 512MB of DDR3. Several connections are available on this boards:
4*USB2.0, 1*USB2.0 typeC, SDcard, RJ45, HDMI, Arduino connector, ...
- Add support of stm32mp157c discovery2 board (part number: STM32MP157C-DK2).
This board is a "super-set" of stm32mp157a-dk1. A display panel (otm8009a)
and Murata wifi/BT combo is added.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Updates the stm32mp157c devicetree to bind the U-Boot PSCI driver need for
power off command; TF-A for stm32mp15x supports PSCI 1.0.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Alignment with kernel driver name & binding
introduced by https://patchwork.kernel.org/cover/10761943/
to use the final marketing name = STPMIC1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Prepare file modification for kernel alignment and
rename driver to stpmic1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
As per recent TRM[1], PBIAS cell on dra7 devices supports
3.3v and not 3.0v as documented earlier.
Update PBIAS regulator max voltage and the voltage written
in the driver to reflect this.
[1] http://www.ti.com/lit/pdf/sprui30
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
With the memory mapping giving us some more avialable RAM, this
updates the da850-evm-u-boot.dtsi to include the serial port, SPI
and Flash nodes along with some dependent nodes in the SPL dtb.
This also removes the platform data initialization code for the
serial port and SPI Flash.
Signed-off-by: Adam Ford <aford173@gmail.com>
This patch adds dt node for DP83867 phy used on K2G ICE board and
also enable netcp device nodes for the board.
EVM hardware spec recommends to add 0.25 nsec delay in the tx
direction and 2.25 nsec delay in the rx direction for internal
delay in the clock path to be on the safer side.
The board straps RX_DV/RX_CTRL pin of on board DP83867 phy in mode
1. Unfortunately, the phy data manual disallows this. Add
ti,dp83867-rxctrl-strap-quirk in the phy node to allow software to
enable workaround suggested for this incorrect strap setting. This
ensures proper operation of this PHY.
The dts bindings are kept in sync with that from 4.14.y linux
kernel. This required the pinmux device related bindings to be
commented out to allow for compilation.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch removes the unused phy-mode property from the phy dt node. On
K2G, currently link-interface determines if phy is used or not and is
already set to use rgmii. So this is not needed. Besides phy-mode should
be added to slave interface configuration of the cpsw driver, not in the
phy node.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
There is no reason not to use the Linux "jedec,spi-nor" binding in U-Boot
dts files. This compatible has been added in sf_probe, let use it.
This patch switches to jedec,spi-nor when spi-flash is used in the DTS
and DTSI files, and removed spi-flash when jedec,spi-nor is already
present.
The x86 dts are switched in a separate commit since it depends on a change
in fdtdec.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Evgeniy Paltsev <paltsev@synopsys.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Patrick Delaunay <Patrick.delaunay@st.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Sync armada-385-db-88f6820-amc.dts with Linux. Retain the
u-boot,dm-pre-reloc and nand differences.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This board was added to u-boot first but the Linux maintainers requested
a more descriptive name. Rename the file to match the Linux usage and
update the board defconfig.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The DB-XC3-24G4XG is a switch development board from Marvell. It can
either use and external CPU card such as the db-88f6820-amc or the
internal CPU that is integrated into the switch.
Add support for running U-Boot on the internal CPU and enable the USB,
SPI and NAND peripherals. For now this needs the bin_hdr from the
Marvell U-Boot for this board.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable the hardware watchdog to guard against system lock ups when
running in the SPL or U-Boot. Stop the watchdog just before booting so
that the OS can re-enable it if needed.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Bring in the Armada 370/XP dts/dtsi files from Linux. As U-Boot hasn't
got the new NAND driver the updating binding has not been included.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Add DT node for MCU NAVSS its components to get DMA working on AM654
SoC.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Texas Instruments' System Control Interface (TI-SCI) Message Protocol
abstracts management of NAVSS resources, like PSI-L pairing and
unpairing, UDMAP tx/rx/flow configuration and Rings.
This patch adds support for requesting and configuring such resources
from TI-SCI firmware.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Import Linux 5.0 DT from 1c163f4c7b3f ("Linux 5.0") for the
meson-gxl-s805x-libretech-ac board and the corresponding changes
in meson-gxl.dtsi.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This adds *-u-boot.dtsi files for p200 and p201 boards
These are just copies of arch/arm/dts/meson-gxbb-odroidc2-u-boot.dtsi
Signed-off-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This adds the device trees for p200 and p201 boards.
Synced from kernel 5.0.0
Commit: a667cb7a94d4 ("Merge branch 'akpm' (patches from Andrew)")
Signed-off-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The E2 Alt board has two USB ports, add missing DT nodes to make the
USB available.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Synchronize R-Car Gen3 device trees with Linux 5.0,
commit 1c163f4c7b3f621efff9b28a47abb36f7378d783 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Synchronize R-Car Gen2 device trees with Linux 5.0,
commit 1c163f4c7b3f621efff9b28a47abb36f7378d783 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The GARDENA smart Gateway boards are equipped with an Atmel / Microchip
AT91SAM9G25 SoC and with 128 MiB of RAM and 256 MiB of NAND storage.
This patch adds support for this board including SPL support. Therefore
the AT91Boostrap is not needed on this platform any more.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This makes it possible to reference the watchdog DT node via "&watchdog"
from board dts files.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Migrate the following options to CONFIG_DM:
CONFIG_DM_GPIO
CONFIG_DM_MMC
CONFIG_DM_ETH
CONFIG_DM_SERIAL
CONFIG_DM_USB
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
After the commit: "eth: dm: fec: Add gpio phy reset binding"
SHA1: efd0b79106
The FEC ETH driver switched to PHY GPIO reset performed with data defined
in DTS.
For the HSC|DDC boards the GPIO reset signal is active low and hence the
wrong DTS description must be changed (otherwise the reset for ETH is not
properly setup).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Activate I2C7 on Alt to allow access to the PMIC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
An ADATA 16GB Industrial MLC card has so much capacitance on the Vcc
pin that the usual toggling of regulator to power the card off and on
is insufficient. When the card is calibrated into UHS SDR104 mode, it
will remain in that mode across the power cycle and subsequent attempt
to communicate with the card will fail.
The test with this card is to insert it into an SDHI slot and perform
"mmc dev 0 ; mmc dev 0", where the second "mmc dev 0" will fail.
Fix this problem by increasing the off-on delay from 0 to 20 mS.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since commit 27cb7300ff ("Ensure device tree DTS is compiled"),
build succeeds irrespective of the correctness of Makefile.
In fact, you can compile any defconfig without adding any entry in
arch/*/dts/Makefile.
As a result, a lot of wrong code have been merged unnoticed.
I am going to revert that commit, and lots of hidden issues have
come to light:
[1] Typos
armada-3720-uDPU.dts, sun8i-a83t-tbs-a711.dts
use the extension ".dts" instead of ".dtb"
[2] DTB is associated to undefined CONFIG option
For example, mx6sllevk_defconfig defines CONFIG_MX6SLL, but
associates its device tree to CONFIG_MX6SL, which is undefined.
[3] Lots of entries are missing
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
[trini: add imx6ul pico dtbs]
Signed-off-by: Tom Rini <trini@konsulko.com>
- Enable network interface on clearfog_gt_8k (Baruch)
- Fix dreamplug boot by adding an spi0 alias to the DT (Chris)
- Fix / enhance Marvell ddr3 setup / parameters (Chris)
- Change CONFIG_SYS_MALLOC_F_LEN to 0x2000 on db-88f6820-amc (Chris)
- Enable SPL_FLASH_BAR on db-88f6820-amc (Chris)
- Use correct pcie controller name in Armada-38x dts files (Chris)
- Disable d-cache on Kirkwood platforms as currently needed (Chris)
- Add a more descriptive comment to pci_mvebu.c (Stefan)
- Update Marvell maintainers entry (Stefan)
When armada-385.dtsi was sync'd from Linux the name of the node
describing the pcie controller was changed from pcie-controller to pcie.
Some of the boards that include armada-385.dtsi were missed in the
update retaining the old name. This updates the affected boards.
Reported-by: Влад Мао <vlaomao@gmail.com>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The conversion to DM_SPI managed to break accessing the environment on
dreamplug. This is because the environment code relies on being to able
to select the SPI device based on the sequence number. Add an alias so
that the spi0 bus gets sequence number 0.
Reported-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: Stefan Roese <sr@denx.de>
Syscon register is required in dts to select correct
PHY interface.
Fix error below:
Net: Failed to get syscon: -2
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
spba-bus has a few nodes under it including the UART1 and
some ESPI buses. In order to use them in SPL, the
u-boot,dm-spl flag needs to be added to the spba-bus@2000000
container.
Signed-off-by: Adam Ford <aford173@gmail.com>
Import the device tree files from kernel 5.0-rc6 in preparation
for driver model conversion.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Just add spaces around '=' sign for clarity.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add startup time to LDO regulators of S2MPS11 PMIC on Odroid XU3/XU4/HC1
family of boards to be sure the voltage is proper before relying on the
regulator.
The datasheet for all the S2MPS1x family is inconsistent here and does
not specify unambiguously the value of ramp delay for LDO. It mentions
30 mV/us in one timing diagram but then omits it completely in LDO
regulator characteristics table (it is specified for bucks).
However the vendor kernels for Galaxy S5 and Odroid XU3 use values of 12
mV/us or 24 mV/us.
Without the ramp delay value the consumers do not wait for voltage
settle after changing it. Although the proper value of ramp delay for
LDOs is unknown, it seems safer to use at least some value from
reference kernel than to leave it unset.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The ADC block requires VDD supply to be on so provide one.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
v2019.01 commit cbff9f80ce ("ARM: dts: rmobile: Sync Gen3 DTs with
Linux 4.19.6") made the sdhi/usb nodes available in r8a77965.dtsi.
Hence, remove the SDHI/USB nodes from r8a77965-u-boot.dtsi. This is
equivalent to partially reverting below v2019.01 commits:
- f529bc551b ("ARM: dts: rmobile: Extract USB nodes on M3N")
- 830b94f768 ("ARM: dts: rmobile: Extract SDHI nodes on M3N")
Duplicating the nodes from <soc>.dtsi to <soc>-u-boot.dtsi is obviously:
- not needed if no U-boot-specific changes are needed in those nodes.
- potentially dangerous/error-prone, since the duplicated properties
override the properties originally defined in <soc>.dtsi. One
possible consequence is that <soc>.dtsi is getting an update from
Linux, while <soc>-u-boot.dtsi stays unchanged. In this situation,
the obsolete property values from <soc>-u-boot.dtsi will take
precedence masking some of the <soc>.dtsi updates, potentially
leading to all kind of obscure issues.
Below is the dtdiff of r8a77965-salvator-x-u-boot.dtb (the only "user"
of r8a77965-u-boot.dtsi) before and after the patch (slightly
reformatted to avoid 'git am/apply' issues and to reduce the width).
What below output means is there is already a mismatch in some of
SDHI/USB nodes between r8a77965.dtsi and r8a77965-u-boot.dtsi. Since no
U-Boot customization is needed in SDHI/USB DT nodes, get rid of them in
r8a77965-u-boot.dtsi.
$> dtdiff before-r8a77965-salvator-x-u-boot.dtb \
after-r8a77965-salvator-x-u-boot.dtb
--- /dev/fd/63 2019-03-09 12:57:40.877963983 +0100
+++ /dev/fd/62 2019-03-09 12:57:40.877963983 +0100
@@ -1471,7 +1471,7 @@
bus-width = <0x4>;
cd-gpios = <0x51 0xc 0x1>;
clocks = <0x6 0x1 0x13a>;
- compatible = "renesas,sdhi-r8a77965";
+ compatible = "renesas,sdhi-r8a77965", "renesas,rcar-gen3-sdhi";
interrupts = <0x0 0xa5 0x4>;
max-frequency = <0xc65d400>;
pinctrl-0 = <0x4d>;
@@ -1492,7 +1492,7 @@
sd@ee120000 {
clocks = <0x6 0x1 0x139>;
- compatible = "renesas,sdhi-r8a77965";
+ compatible = "renesas,sdhi-r8a77965", "renesas,rcar-gen3-sdhi";
interrupts = <0x0 0xa6 0x4>;
max-frequency = <0xbebc200>;
power-domains = <0x1 0x20>;
@@ -1504,7 +1504,7 @@
sd@ee140000 {
bus-width = <0x8>;
clocks = <0x6 0x1 0x138>;
- compatible = "renesas,sdhi-r8a77965";
+ compatible = "renesas,sdhi-r8a77965", "renesas,rcar-gen3-sdhi";
fixed-emmc-driver-type = <0x1>;
interrupts = <0x0 0xa7 0x4>;
max-frequency = <0xbebc200>;
@@ -1526,7 +1526,7 @@
bus-width = <0x4>;
cd-gpios = <0x5a 0xf 0x1>;
clocks = <0x6 0x1 0x137>;
- compatible = "renesas,sdhi-r8a77965";
+ compatible = "renesas,sdhi-r8a77965", "renesas,rcar-gen3-sdhi";
interrupts = <0x0 0xa8 0x4>;
max-frequency = <0xc65d400>;
pinctrl-0 = <0x56>;
@@ -1868,14 +1868,14 @@
usb-phy@ee0a0200 {
#phy-cells = <0x0>;
- clocks = <0x6 0x1 0x2be>;
+ clocks = <0x6 0x1 0x2bf>;
compatible = "renesas,usb2-phy-r8a77965", "renesas,rcar-gen3-usb2-phy";
phandle = <0x47>;
pinctrl-0 = <0x4c>;
pinctrl-names = "default";
power-domains = <0x1 0x20>;
reg = <0x0 0xee0a0200 0x0 0x700>;
- resets = <0x6 0x2be>;
+ resets = <0x6 0x2bf>;
status = "okay";
};
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
U-Boot currently uses Gen2 QSPI in 1-bit mode, enforce it until
we can do better using the new SPI NOR framework.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch enables UMS on the nyan devices like the nyan-big.
A patch like this has been sent in by Stephen Warren some time ago for
other tegra devices: commit e6607cffef.
But the nyan devices never received that functionality.
Signed-off-by: Tristan Bastian <tristan-c.bastian@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Internal keyboard of nyan-big is only working when cold booting by pressing [reload/refresh]+[power] button.
With this patch keyboard is working by only pressing [power] button.
Signed-off-by: Tristan Bastian <tristan-c.bastian@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
- Switch to using the omap3-u-boot.dtsi file for needed properties.
- Remove a few SPL features to free up more SRAM space.
- Switch CONFIG_SYS_TEXT_BASE to the normal default, we don't need to
worry about X-Loader at this point anymore.
- A few related updates to SPL options as part of switching to DM SPL.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
With the generic omap3-u-boot.dtsi file available, this patch
increased the memory of the various incarnations of the omap3_logic
board, and points their respective u-boot.dtsi files to the newly
created generic one, and removes the PLATDATA from the board file.
These are all done at once because the're all utilizing the same
omap3logic.c board file.
Signed-off-by: Adam Ford <aford173@gmail.com>
Create generic omap3-u-boot.dtsi file that omap3 based boards
can include to generate device tree in SPL for booting MLO.
Credit should go to Tom Rini.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
This commit converts the brxre1 board to DM,
for this we have todo following things:
- add a devicetree-file for this board
- drop all obsolete settings from board header-file
- use dm_i2c_xxx calls for read/write to the resetcontroller
- request gpios before operate them
Serues-cc: trini@konsulko.com
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
LX2160AQDS is a development board that supports LX2160A
family SoCs. This patch add base support for this board.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[PK: Sqaush patch for "secure boot defconfig" & add maintainer]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
As the H5 is pin compatible with the H3, vendors tend to upgrade their
existing H3 products with an H5 SoC swap. This is the case with the
Bananapi M2+ H5.
Add the following to support it:
- device tree file: synced from Linux v5.0-rc1,
- defconfig: copy of bananapi_m2_plus_h3_defconfig with only SoC
family and default device tree file name changed
- MAINTAINERS entry
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
As of commit aa8fee415f46 ("ARM: dts: sun8i: h3: Split out
non-SoC-specific parts of Bananapi M2 Plus") in the Linux kernel, the
device tree for the Bananapi M2+ has been split into a common dtsi file,
and an SoC-specific board device tree file that includes both the shared
dtsi file and the soc dtsi file. This was done to support both the H3
and H5 variants of the same board. This is similar to what was done for
the Libre Computer ALL-H3-CC in U-boot commit d7b17f1c24 ("sunxi: Split
out common board design for ALL-H3-CC device tree").
The newly split files are directly synced from Linux tag v5.0-rc1.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Update all the dts[i] files for imx6[q|qp|dl] sabre[auto|sd] to the ones
from kernel v4.20 (commit 8fe28cb58bcb2).
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
This allows us to keep the basic dts[i] files up-to-date with
the ones in kernel, but at the same time allowing the u-boot
to add its own properties to the existing nodes.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
As per the zc1275 design x1 mode is enabled so changing the
spi-rx-bus-width property to x1.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The idle-states binding documentation[1] mentions that the
'entry-method' property is required on 64-bit platforms and must be
set to "psci".
Linux commit a13f18f59d26 ("Documentation: arm: Fix typo in the idle-states
bindings examples") attempted to fix this earlier but clearly more is
needed.
Linux docs:
Documentation/devicetree/bindings/arm/idle-states.txt (see
idle-states node)
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds reset-on-timeout to FPD WDT which will trigger an
interrupt to PMU when watchdog expiry happens and PMU takes the
necessary action. If this property is not enabled, reason will not be
known when watchdog expiry happens.
This patch also modifies the default timeout to 60 seconds. Reason is
that if u-boot enables WDT, it will set the timeout to 10 seconds and
this is not enough to boot till Linux and start the WDT application in
Linux. 60 seconds is the maximum safest value to boot till Linux and
start the WDT application.
Users need to change this timeout value to fit their needs.
Signed-off-by: Mounika Grace Akula <mounika.grace.akula@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Replace the current value of the model property by a more accurate
description of each board (which includes the manufacturer), as some
of the boards had the same value ("Xilinx Zynq")
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Both boards are made by Avnet, Inc. So add an additional
value to the compatible property
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Import liteSOM and liteboard dts files from Linux v4.20. They will
be used after transition to driver model and device-tree based boot.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
CONFIG_PCA953X is not needed because of PCA953X is integrated in gpio
subsystem already. That's why also remove CMD_PCA953X which is only for
this driver.
zcu102/zcu104-revC/zcu106/zcu111 contain links to eeprom which stores MAC address.
DM_I2C is not enabled for the whole SoC because it increase size for
mini configurations and there is no I2C symbol present to setup
dependencies.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Boards have only one controller enabled that's why move to DM_I2C is
easy.
Add also i2c alias for not to be shown as i2c bus -1 because alias
doesn't exist.
Config file points to MAC stored in eeprom but it is not listed that's
why I have added 24c08 part.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This patch adds new mini target for versal.
This configuration is very minimal in size which runs
from OCM. It contains support for mtest which can be
used for running DDR memory tests.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds mini eMMC configuration which has only
emmc0 and emmc1 functionalities and can run from small
amount of memory. This is required for memory constraint
devices.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The PCIe slot PERST signal is active low. Fix the gpio signal
description in the dts.
This happened to work because the pcie_dw_mvebu driver sets the reset
gpio level to 1 (high) to release the reset. The following commit will
fix that.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Common sound support
buildman environment support
of-platdata documentation improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlxf7igRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYKfggApQiL0Gv6NdGAQN+zfpjKY5a2QyjKsAxa
KLm3q8XyXIQXufMWOEPoW1iWm0iixpIFgChy8ff3m/OPDzsx99UXDTyvjitsSxtQ
5tFu8K78nUZT6OOE3HNhhlyW/xK442oKBzGt4MUt3kUZOELsCNuftgbJUWksHuO3
6pPrgt36E0uRGbUA4ioYCU336viJRPOOCdqb8hHViEihFj/IEv5T82RdE5y97YxG
dT7BZxjPkBH5ZN1uD/tdxG1k6IZBagZiYoDAsYp4YqNwmVsm5sLrZ9QVSf7EcH/y
qX8butZesiMd7xm7RROlrIImh7fb36N3zsoRiUWZDo1Al3IRkmZyVA==
=tdut
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-10feb19' of git://git.denx.de/u-boot-dm
Samsung sound patches (applied for Samsung maintainer)
Common sound support
buildman environment support
of-platdata documentation improvements
Update the flashmap so that this board can be started over USB A-A. It
is slightly different from snow.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Update the spring settings to use this codec, which is what it actually
shipped with.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
This add the initial support of the broadcom reference
board bcm963158 with a bcm63158 SoC.
This board has 1 GB of ram, 512 MB of flash (nand),
2 usb port, 1 uart, 4 ethernet ports (LAN), 1 ethernet port (WAN).
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
This add the initial support of the broadcom bcm63158 SoC family,
only the cpu, dram and uart are supported.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
- Add st,digbypass on clk_hse node (needed for board rev.C)
- MLAHB/AHB max frequency increased from 200 to 209MHz, with:
- PLL3P set to 208.8MHz for MCU sub-system
- PLL3Q set to 24.57MHz for 48kHz SAI/SPI2S
- PLL3R set to 11.29MHz for 44.1kHz SAI/SPI2S
- PLL4P set to 99MHz for SDMMC and SPDIFRX
- PLL4Q set to 74.25MHz for EVAL board
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
commit fdce9d35dc ("arm: dts: am33xx: Sync dts with Linux 4.20.0")
did remove the "u-boot,dm-spl" flag from the 'ocp' bus which was
introduced with
commit 19aa4ac09d ("dts: am33xx: add u-boot, dm-spl to ocp bus")
Due to this all boards having CONFIG_SPL_OF_CONTROL enabled are broken
because they cannot bind/probe the boot-media interface during SPL
stage.
This commit introduces the 'am33xx-u-boot.dtsi' which is included with
the auto include mechanism. The am33xx-u-boot-dtsi adds the important
"u-boot,dm-pre-reloc" to the 'ocp bus' (the root bus of almost all
peripherals, at least the bootable ones).
The peripherials (mmc, spi, ...) needed during SPL stage need to be
equipped with the 'u-boot,dm-pre-reloc' in their responsible dts file.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
With the new DM_VIDEO support in the Armada XP LCD driver, this patch
adds the needed DT node for the LCD controller to the theadorable dts
file. This DT property is not added to the Armada XP dtsi files, as this
LCD feature is pretty unusual for this SoC and I personally know of no
other board that uses this controller.
This patch also enables CONFIG_BMP_16BPP/24BPP/32BPP, as the "old" bmp
command supported these BMP files.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
This adds initial support for micro-DPU (uDPU) board which is based on Armada-3720 SoC.
micro-DPU is the single-port FTTdp "distribution point unit" made by Methode Electronics
which offers complete modularity with replaceable SFP modules both for uplink and downlink
(G.hn over twisted-pair, G.hn over coax, 1G and 2.5G Ethernet over Cat-5e cable).
On-board features:
- 512 MiB DDR3
- 2 x 2.5G SFP via HSGMII SERDES interface to the A3720 SoC
- USB 2.0 Type-C connector
- 4GB eMMC
- ETSI TS 101548 reverse powering via twisted pair (RJ45) or coax (F Type)
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Luis Torres <luis.torres@methode.com>
Cc: Scott Roberts <scott.roberts@telus.com>
Cc: Paul Arola <paul.arola@telus.com>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Now that the PCIe driver supports DM and DT parsing, enable the PCIe DT
nodes that are used by this board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: VlaoMao <vlaomao@gmail.com>
This patch sync's the PCIe DT nodes with the recent Linux v4.20 version.
This change makes it easier to reference specific PCIe nodes in the
board dts files to e.g. enable a PCIe port as this is now necessary with
the new DM PCI driver for these platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: VlaoMao <vlaomao@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
* support for Chromebook Bob
* full pinctrl driver using DTS properties
* documentation improvements
* I2S support for some Rockchip SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcVG0IAAoJECaAFcEOcohNKVAIAJd3DN/qudcVQdkuvAGK6WIk
Umxkm6rxHwur7oU+wxvK1p1l/0YTFBeCfo15quH1DkSc/WIUnmBlLmDvqpGVmPmh
ydZNE9ZChn0OKRIaM6pKJr+3p155cQDe6Mgg2j/5CnNx28KxT+vu7EqZbZvbQPag
wcZEK6Z6E5jMVHVn2lbLgmsBPmY7ksX168IqpvzTxIj0a4J3n0DcJUnO4RBBS0Q2
PGEvFhTvigVWs6r6GL0gLn3VwnQX30xQlIuKKORPcdhjk97cJcS4+bRxdTENTKD9
j3+pgyl1n04O8sPONZS7pH3fvJwtC6SwnoxTYxGrvjedw1LxbyHG3cqcGDg/TJ8=
=ik3X
-----END PGP SIGNATURE-----
Merge tag 'for-master-20190201' of git://git.denx.de/u-boot-rockchip
u-boot-rockchip changes for 2019.04-rc1:
* support for Chromebook Bob
* full pinctrl driver using DTS properties
* documentation improvements
* I2S support for some Rockchip SoCs
Add some U-Boot-specific settings. These should really go in the
*u-boot.dtsi file, but it seems that rk3399 does not use that yet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This memory is used on Bob. Add settings for this, taken from coreboot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This file has changed upstream, with some additions and changes. Move the
U-Boot version towards this.
Some USB changes seem to be incompatible with how the bindings work on
rockchip in U-Boot. Testing is needed to make sure that USB still works
correct, and adjust the code (not device tree) if not.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Bring in these files from Linux v4.20.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
To match the iomux setting of uart2 at SPL, correct the uart2
default pin configuration, if not changed, the evb-rk3229 can't
output the log message.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This adds support for the ASUS C201, a RK3288-based clamshell
device. The device tree comes from linus's linux tree at
3f16503b7d2274ac8cbab11163047ac0b4c66cfe. The SDRAM parameters
are for 4GB Samsung LPDDR3, decoded from coreboot's
src/mainboard/google/veyron/sdram_inf/sdram-lpddr3-samsung-4GB.inc
Signed-off-by: Marty E. Plummer <hanetzer@startmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Like on rk3399-puma we want to continue booting the fill U-Boot from
the same device as the SPL stage.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Jerry uses a max98090 audio codec and the internal SoC I2S peripheral.
Enable sound support and add the required device-tree pieces.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Although not required, it doesn't hurt to explicitly map the USB ports to
a USB controller. Without this, the port number will be derived from the
binding order of the peripheral devices.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This USB port is mainly used for RNDIS and DFU. To be able to use it with
DM_USB and DM_USB_GADGET, we need to provide a dr_mode value in the DTS.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
add u-boot specific am335x-shc-u-boot.dtsi file,
in which we add u-boot specific adaptions.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
add DTS from linux tree commit
"47bfa6d9dc8c060bf56554a465c9031e286d2f80"
change for U-Boot:
switch to SPDX-license identifier.
Signed-off-by: Heiko Schocher <hs@denx.de>
There's no reliable way to reuse the hhi entry from the vpu as is done
in the linux kernel, so we duplicate it here.
We will be able to sync against kernel DTS in the future when the VPU
gets based on the clock framework rather than the HHI reg.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The hdmi_5v regulator must be enabled to provide power to the physical HDMI
PHY and enables the HDMI 5V presence loopback for the monitor.
Fixes: b409f625a6d5 ("ARM64: dts: meson-gx: Add HDMI_5V regulator on selected boards")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
[backport of linux commit e1f2163deac059ad39f07aba9e314ebe605d5a7a]
Flag the appropriate nodes with u-boot,dm-pre-reloc
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Like other Allwinner A64 boards, pinebook also need altering
auto-numbering of mmc2 to mmc1 which is available in common
sunxi dsti file, sunxi-u-boot.dtsi
Pinebook has a separate sun50i-a64-pinebook-u-boot.dtsi which
takes more precedence for u-boot.dtsi inclusion and it eventually
failed to include the sunxi-u-boot.dtsi.
So, this patch add support to include the sunxi-u-boot.dtsi in the
sun50i-a64-pinebook-u-boot.dtsi
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com> # Pinebook
Environment and fastboot mmc devices are configured based on the number
of mmc slots defined on particular board configs, MMC_SUNXI_SLOT_EXTRA.
If MMC_SUNXI_SLOT_EXTRA is more than 1, the default env and fastboot
mmc devices is mmc1 by assuming mmc0 is SD and mmc1 is emmc device.
But with DM_MMC the mmc devices are numbered as per the dts node
enablement. If there is a chance of having enabling all mmc nodes
in dts say mmc0, mmc1, mmc2 then the default env and fastboot devices
will failed to assign proper emmc device since mmc2 is emmc in most
of the Allwinner platforms.
So, we need to alter the auto-numbering by aliasing mmc2 to mmc1 since
aliases take precedence over auto-numbering.
If the dts enables mmc0, mmc1, mmc2, then all the nodes will probe
sequentially and auto-numbered as it is. but when aliases mmc1 with mmc2
the resulting number should be that mmc0 is till mmc0, mmc2 become mmc1
and mmc2 become mmc1
Without aliases of mmc1 = &mmc2;
-------------------------------
MMC: mmc@1c0f000: 0, mmc@1c10000: 1, mmc@1c11000: 2
With aliases of mmc1 = &mmc2;
----------------------------
MMC: Device 'mmc@1c11000': seq 1 is in use by 'mmc@1c10000'
mmc@1c0f000: 0, mmc@1c10000: 2, mmc@1c11000: 1
Loading Environment from FAT... OK
Some platforms like A20 has mmc0...mmc3, but there is no usecases now
for enabling all mmc controllers in any of A20 board dts files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The i.MX6 SOM and development kits have undergone significant
updates and changes over the past few months. This re-sync's
the U-Boot with Logic PD's BSP.
Signed-off-by: Adam Ford <aford173@gmail.com>
This patch sets up an alias for mmc0 to usdhc3.
Before the DM conversion only usdhc3 was enabled and therefore it appeared
as MMC 0 to u-boot. After enabling MMC DM though usdhc3 defaults to MMC 2,
which left unattended would drive changes to existing warp7 bootscripts and
environment variables that rely on mmc 0.
Setup the alias of mmc0 and usdhc3 so that existing warp7 boot code will
work unmodified.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
This patch imports the Linux kernel warp7 dts as at upstream kernel commit
cf76c364a1e1.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
As pointed out by Lucas WDOD1_WDOG_ANY should be WDOG1_WDOG_ANY. Once
corrected we can import the latest kernel DTS unmodified.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reported-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
These nodes are required by CX9020 when build with CONFIG_DM_MMC=y
They are copied from Linux 4.20
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Introduce u-boot dtsi for i.MX8QXP MEK board.
we do not introduce a common dtsi for SoC, because different board
has different requirement on which needs to be enabled in SPL DM.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In preparation of adding CONFIG_DM_MMC support use separate device
trees for raw NAND and eMMC devices.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Port for the PHYTEC phyBOARD-i.MX6UL-Segin single board computer. Based on
the PHYTEC phyCORE-i.MX6UL SOM (PCL063).
CPU: Freescale i.MX6UL rev1.2 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 44C
Reset cause: POR
Board: PHYTEC phyCORE-i.MX6UL
I2C: ready
DRAM: 256 MiB
NAND: 512 MiB
MMC: FSL_SDHC: 0
In: serial
Out: serial
Err: serial
Net: FEC0
Working:
- Eth0
- i2C
- MMC/SD
- NAND
- UART (1 & 5)
- USB (host & otg)
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
As Poplar supports running TF-A with OP-TEE as BL32
payload, add op-tee node in DT, which enables usage of
OP-TEE driver (which provides an interface for requesting services
from OP-TEE).
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
It adds missing pinctrl headers, updates clock header and sync up Poplar
device tree with kernel 4.20 release.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
* Add pinctrl node for TLMM and add mux request for uart node.
* Rename uart to the actual board uart port.
* Fix indentendation of sdhc2 node.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
The miamiplus contains a speedgrade-2 device, which may run the CPU at 800MHz.
Change the PLL setting to 800MHz, and adapt the setpoints in the devicetree.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patches renames sd nodes in dts to be in line with
kernel. This patch also modifies the references for the same
in code.
It checks mmc first to have no time penalty for new DT node names based
on left-to-right expression evaluation.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This is a range of stackable network switches. The SoC is Armada-385 and
there are a number of variants with differing network port
configurations. The DP variants are intended for a harsher operating
environment so they use a different i2c mux and fit industrial-temp
parts.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The memory area [0x4000000-0x4200000[ is occupied by the PSCI firmware. Any
attempt to access it from U-Boot leads to an immediate crash.
So let's make the same memory reservation as the vendor device tree.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
DTC issues a warning because #address-cells and #size-cells properties
are not set in the mdio node.
Also add ethernet1 alias.
Also add RTC node.
Also fix USB3 regulator startup delay time.
Also fix PCI Express SERDES speed to 5 GHz (this is only cosmetic, the
speed value is not used byt the comphy driver for PCI Express, but
should be 5 GHz nonetheless).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Check if Mox modules are connected in supported mode, then configure
the MDIO addresses of switch modules.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Sync the Armada-38x device tree files with Linux 4.20-rc5. The changes
not taken are new compatible strings for the uart and nand flash
controller. The nand binding is best updated if/when the mtd/nand
infrastructure is updated.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Update all A80 devicetree dtsi and dtsi files from
Linux-v4.18-rc3 with below commits.
arch/arm/boot/dts/sun9i-a80*:
commit 190e3138f9577885691540dca59c2f07540bde04
Merge: cafc87023b0d a7affb13b271
Author: Arnd Bergmann <arnd@arndb.de>
Date: Tue Mar 27 14:58:00 2018 +0200
Merge tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
include/dt-bindings/*/sun9i-a80-*:
commit 783ab76ae553abc23f80ef7511052d055697531b
Author: Chen-Yu Tsai <wens@csie.org>
Date: Sat Jan 28 20:22:36 2017 +0800
clk: sunxi-ng: Add A80 Display Engine CCU
Note: sun9i-a80-cx-a99.dts is updated only uart0, since the same
dts is not available in Linux.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Emlid Neutis N5 is a SoM based on Allwinner H5, has a WiFi & BT
module, DDR3 RAM and eMMC.
- add neutis-devboard target to dtb makefile
- add dtsi file for Neutis N5 needs
- add config file for Neutis N5 Dev board
Signed-off-by: Aleksandr Aleksandrov <aleksandr.aleksandrov@emlid.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: update proper commit head]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Remove aliases property name warning while compilation:
Warning (alias_paths): /aliases: aliases property name must
include only lowercase and '-'
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls2088ardb_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- remove EL3 specific erratas for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This adds device tree for OMAP3 IGEP based boards and the DM_MMC driver.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add MMC nodes for HiKey board based on HI6220 SoC. There are three MMC
controllers in this SoC, first one used for eMMC, second one used
for SD card and third one is not used by u-boot.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The SDMMC reset is missing from DT, so the reset manager cannot unreset
the SDMMC. Add the missing DT reset entry.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
This patch sets VDD_LOG to 950 mV on RK3399-Q7.
This is required to address stability issues on Puma
in heavy-load use-cases.
Reported-by: Assaf Agmon <assaf@r-go.io>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch eliminates the non-standard entries "rockchip,pwm_id"
and "rockchip,pwm_voltage". They are neither documented nor
read out by any driver.
Additionally it introduces the entry regulator-init-microvolt
and sets it to 900 mV, which is the default target value
for VDD_LOG.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This file is in sync with v4.20-next tree:
e4dda4f5a4df "x86/kaslr, ACPI/NUMA: avoid including asm/kaslr.h on arm64"
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This node is in sync with v4.20-next tree:
e4dda4f5a4df "x86/kaslr, ACPI/NUMA: avoid including asm/kaslr.h on arm64"
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Currently, the DWC3 USB node is out of sync because the bindings
for the UniPhier DWC3 PHY diverged between Linux and U-Boot.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Under U-boot, the WiFi SDIO Module should be disabled and the
eMMC modules should be enabled, so this patch adds an s400-u-boot.dtsi
include file specific for U-Boot that will be included by the build system.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Add the initial support for Elgin R1 board, which is based on the
RV1108 SoC and has the following features currently supported in
U-Boot:
- UART
- eMMC
- USB
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This is a sync with kernel mainline dts.
The U-Boot eMMC does not need to care about the power for Rockchip
SoCs, because if the board is using eMMC, the power will default on
(for bootrom), so the 'vmmc', 'vqmmc' is only useful for SD in U-Boot.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
vcc5v0_host and usbhub_enable share gpio4 RK_PA3,
which is a problem during probing (the second probe
will trigger a -EBUSY, when trying to get the gpio handle).
An analysis of the situation shows, that both regulators
are actually describing the same supply.
This patch removes the (currenlty not successful probing)
regulator vcc5v0_host from the DTS and adds the pinctrl-*
setting to usbhub_enable.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Phiilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Commit 4687919684 ("serial: Remove DM_FLAG_PRE_RELOC flag in various
drivers") essentially drops flag DM_FLAG_PRE_RELOC from serial_pl01x
driver for Poplar platform, because the platform falls into the
following strategy category made by the commit.
Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Before the commit lands, Poplar platform works by statically declaring
pl011 serial device via U_BOOT_DEVICE() with DM_FLAG_PRE_RELOC flag set
in the driver. But since Poplar also supports device configuration from
device tree, the commit practically drops the flag for Poplar, and hence
breaks the platform from booting.
This patch changes platform code and device tree to initiate pl011
serial device from device tree rather than static declaration, so that
above strategy about DM_FLAG_PRE_RELOC applies to Poplar, and therefore
the reported boot failure gets fixed.
Reported-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Fixes: 4687919684 ("serial: Remove DM_FLAG_PRE_RELOC flag in various drivers")
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Tested-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
USB1 can be used by the romboot on all am4372 platforms to download a
firmware (SPL in our case).
It makes sense to enable USB1 in the SPL to download u-boot.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This file is used to override the values found in am4372.dtsi
Use it to fix the "compatible" options for the controllers used
to support the USB (parent bus and syscons).
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update snow's device tree and config to use driver model for sound. Also
update the others as best we can.
Spring does not appear to have audio support in the kernel. The smdk5250
and smdk5420 boards use a wolfson codec which I cannot test with. So the
only boards that is tested and known to work are snow, pit and pi.
Signed-off-by: Simon Glass <sjg@chromium.org>
