Macro MVNETA_GMAC_FORCE_LINK_UP can be dropped from value assignment in
fixed link case, since it's value is written into the register later in
the function for link-down-to-link-up case. The value is written as
MVNETA_GMAC_FORCE_LINK_DOWN | MVNETA_GMAC_FORCE_LINK_PASS, and so the
macro definition can also be dropped.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Guard the code handling the fixed PHY case by
CONFIG_IS_ENABLED(PHY_FIXED).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Since this member is checked only at two places drop it and inline it's
usage.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Write PHY address just before enabling HW polling of the PHY.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Stop parsing fixed-link in the MAC driver. Instead support only PHY mode
and let the fixed PHY driver handle the fixed-link case.
Enable CONFIG_PHY_FIXED for mvneta boards that need it: Turris Omnia and
ESPRESSObin.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The CONFIG_* macros are reserved for Kconfig. This was probably done
when this driver was being imported from Linux. Rename the macro.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Drop checking for CONFIG_PHYLIB in mvneta, this is already done in
Kconfig.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Drop unnecessary space in mvneta_adjust_link().
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Use the bool type instead of int for status_change variable.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Drop one indentation level in the mvneta_adjust_link() function.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The `ret` variable in mvneta_probe() is unused if DM_GPIO is disabled.
Since the variable is used only once after assigning value, we can
inline the usage and drop the variable.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This MDIO bus is now handled by a proper mvmdio DM driver. Remove it
from mvneta.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
We don't need to remember PHY address anymore, because since using DM
MDIO for connecting PHY, the address is parsed by mdio-uclass from
the ofnode.
But the driver uses a special value of the address to signal fixed link
usage.
Drop phyaddr add fixed_link in driver private structure. This simplifies
code a little.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Use the modern DM MDIO API for connecting PHY in the mvneta driver.
This requires enabling MVMDIO driver in several config files.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
In mvneta_adjust_link() we need to set MII_SPEED bit only if PHY reports
the speed at 100Mbps.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Drop .of_to_plat() from the mvneta driver and parse the two properties
in .probe().
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This patchs adds the ethernet & MDIO driver for the MIPS Octeon II / III
SoC platform. Please note that these drivers are based on the 2013
U-Boot version from Marvell and make use of the platform supported
helper functions for the ethernet functionality, including stuff like
SFP handling.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The virtio PCI capabilities describe regions of memory that should be
mapped. Map those with dm_pci_map_bar() which will ensure they are valid
PCI regions.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Prepare for calls to `virtio_pci_map_capability()` failing by returning
NULL on error. If this happens, later accesses to the pointers would be
unsafe so cause the probe to fail if such an error occurs.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a mask parameter to control the lookup of the PCI region from which
the mapping can be made.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add mask parameter and reorder length parameter to match the other PCI
address conversion functions. Using PCI_REGION_TYPE as the mask gives
the old behaviour.
It's converted from a macro to an inline function as the length
parameter is now used twice, but should only be calculated once.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When converting addresses, apply a mask to the region flags during
lookup. This allows the caller to specify which flags are important and
which are not, for example to exclude system memory regions.
The behaviour of the function is changed such that they don't
preferentially search for a non-system memory region. However, system
memory regions are added after other regions in decode_regions() leading
to a similar outcome.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Evolve dm_pci_map_bar() to include an offset and length parameter. These
allow a portion of the memory to be mapped and range checks to be
applied.
Passing both the offset and length as zero results in the previous
behaviour and this is used to migrate the previous callers.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When converting between PCI bus and physical addresses, include a length
parameter that can be used to check that the entire range fits within
one of the PCI regions. This prevents an address being returned that
might be only partially valid for the range it is going to be used for.
Where the range check is not wanted, passing a length of 0 will have the
same behaviour as before this change.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When parsing the `ranges` DT node, check that both extremes of the
regions are addressable without overflow. This assumption can then be
safely made when processing the regions.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The flags parameter of dm_pci_map_bar() is used for PCI region flags
rather than memory mapping flags. Fix the type to match that of the
region flags and stop using the regions flags as memory mapping flags.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Read the virtio PCI capability out of the device configuration space to
a struct rather than accessing fields directly from the configuration
space as they are needed. This both makes access to the fields easier
and avoids re-reading fields.
Re-reading fields could result in time-of-check to time-of-use problems,
should the value in the configuration space change. The range check of
the `bar` field and the later call to `dm_pci_read_bar32()` is an
example of where this could happen.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Ensure the virtio PCI capabilities are contained within the bounds of
the device's configuration space. The expected size of the capability is
passed when searching for the capability to enforce this check.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Check that the common config is at least as large as the struct it is
expected to contain. Only then is it safe to cast the pointer and be
safe from out-of-bounds accesses.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Make sure virtio notifications are written within their allocated
buffer.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The device config is optional, so check it was present and mapped before
trying to use the pointer. Bounds violations are an error, not just a
warning, so bail if the checks fail.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The length of the device config was erroneously being taken from the
notify capability. Correct this by finding the length in the device
capability.
Fixes: 550435edf8 ("virtio: pci: Support non-legacy PCI transport device")
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a new config to control whether the driver for legacy virtio PCI
devices is included in the build. VIRTIO_PCI_LEGACY is included by
default when VIRTIO_PCI is selected, but it can also be independently
toggled.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
lib/charset.c is not optional for
EFI_APP || EFI_LOADER || UFS || UT_UNICODE.
These must select CONFIG_CHARSET.
Fixes: 726cd9836d ("efi: Make unicode printf available to the app")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add Nuvoton NPCM BMC Flash Interface Unit(FIU) SPI master
controller driver using SPI-MEM interface.
The FIU supports single, dual or quad communication interface.
The FIU controller driver provides flash access in UMA(User
Mode Access) mode by using an indirect address/data mechanism.
the dts node is followed upstream kernel dts name.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[Jagan: fixed the Kconfig, Makefile order]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add Macronix mx25u51245g flash entry, so this can be used on
SoCFPGA devices.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
[Jagan: updated commit head]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add ID for Winbond W25Q128JW device. This is a 128 Mbit QSPI NOR.
Tested on W25Q128JWPIM part.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Vignesh R <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
To quote the author:
U-Boot provides a verified-boot feature based around FIT, but there is
no standard way of implementing it for a board. At present the various
required pieces must be built up separately, to produce a working
implementation. In particular, there is no built-in support for selecting
A/B boot or recovery mode.
This series introduces VPL, a verified program loader phase for U-Boot.
Its purpose is to run the verified-boot process and decide which SPL
binary should be run. It is critical that this decision happens before
SPL runs, since SPL sets up SDRAM and we need to be able to update the
SDRAM-init code in the field.
Adding VPL into the boot flow provides a standard place to implement
verified boot. This series includes the phase itself, some useful Kconfig
options and a sandbox_vpl build for sandbox. No verfied-boot support is
provided in this series.
Most of the patches in this series are fixes and improvements to docs and
various Kconfig conditions for SPL.
Add support for VPL, a new phase of U-Boot. This runs after TPL. It is
responsible for selecting which SPL binary to run, based on a
verified-boot process.
Signed-off-by: Simon Glass <sjg@chromium.org>
For most Kirkwood boards, the PHY page is already set to page 0
(in register 22) before phy_connect is invoked. But some board like
the Zyxel NSA310S (which uses the network chip MV88E1318S), the PHY page
is not set to page 0. There seems to be some bad data remained in
register 22 when the uclass MVGBE about to invoke phy_connect().
This patch enables the uclass MVGBE to always set the PHY page to 0
before phy_connect.
For reference, please see this discussion:
[RFC PATCH v2] arm: kirkwood: nsa310s: Use Marvell uclass mvgbe
and PHY driver for DM Ethernet.
https://lists.denx.de/pipermail/u-boot/2022-April/480946.html
This patch has been tested with the following Kirkwood boards:
NSA310S (88F6702, network chip MV88E1318S)
Sheevaplug (88F6281, network chip MV88E1318)
Pogo V4 (88F6192, network chip 88E1116R)
GF Home(88F6281, network chip 88E1116R)
Dreamplug (88F6281, network chip MV88E1318)
Dell Kace M300 (88F6282, network chip MV88E1318) - out of tree u-boot
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Data is written for each channel but is only tracked as having one
channel written. This resulted in a buffer overflow and corruption of
the allocator's metadata which caused further problems when the buffer
was later freed. This could be observed with sandbox unit tests.
Resolve the overflow by tracking the writes for each channel.
Fixes: f987177db9 ("dm: sound: Use the correct number of channels for sound")
Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The buffer is 512 bytes but read requests can be 800 bytes. Limit the
request to the size of the buffer.
Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
When copying the string in copy_to_unicode(), check for the null
terminator in each position, not just at the start, to avoid reading
beyond the end of the string.
Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
There are expecte to be bars 0 through 5, but the last of these was
missing leading to an read beyond the buffer. Add the missing element
with zero values.
Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This function is empty, drop it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Steven Lawrance <steven.lawrance@softathome.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The top level DT node of gpio-leds is not a LED itself, bind NOP uclass
driver to it, and bind different LED uclass driver to its subnodes which
represent the actual LEDs. This simplifies the probe() implementation
and fixes the bogus top-level not-an-LED in 'led list' command output:
```
=> led list
led Error -121 <--- This is removed/fixed by this patch
green:user0 off
```
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Steven Lawrance <steven.lawrance@softathome.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Since 2d1deaf88e ("led: gpio: Drop duplicate OF "label" property parsing"),
all LED nodes have some sort of label. Use device_is_compatible(..."leds-gpio")
to determine whether this is a top-level node, since it is only the top
level node which is compatible with "leds-gpio", the GPIO LEDs subnodes
are not.
Fixes: 2d1deaf88e ("led: gpio: Drop duplicate OF "label" property parsing")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Steven Lawrance <steven.lawrance@softathome.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Calling device_probe() from uclass .post_bind() callback has all kinds
of odd side-effects, e.g. device instances not being available just yet.
Make use of the DM_FLAG_PROBE_AFTER_BIND instead, mark device instances
which need to be probe()d in order to configure the LED default state
with this flag and let the DM core do the device_probe() at the right
time instead.
Fixes: 72675b063b ("led: Configure LED default-state on boot")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Steven Lawrance <steven.lawrance@softathome.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Introduce DM_FLAG_PROBE_AFTER_BIND flag, which can be set by driver or
uclass in .bind(), to indicate such driver instance should be probe()d
once binding of all devices is complete.
This is useful in case the driver determines that hardware initialization
is mandatory on boot, and such initialization happens only in probe().
This also solves the inability to call device_probe() from .bind().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Steven Lawrance <steven.lawrance@softathome.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
It looks quite weird that for non PPC platforms cpu driver for MPC83xx can
be selected. That's why define proper dependency.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Upstream Linux kernel uses for mpc8548-based PCIe controllers compatible
string "fsl,mpc8548-pcie". So change U-Boot fsl PCIe driver and all DTS
files to use "fsl,mpc8548-pcie" instead of "fsl,pcie-mpc8548" to be
compatible with Linux kernel.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
QorIQ pre-PBL BootROM scans first 24 SD card sectors (each with fixed 512
bytes length) for boot signature. Implement same redundancy behavior in
fsl_esdhc_spl driver to allow loading proper U-Boot when boot sector is not
the first one.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
According to Linux kernel DT schema nand-controller.yaml, using DT property
nand-ecc-algo=bch is the correct way for specifying BCH as ECC algorithm.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Initialize ECC configuration after nand_scan_ident() call and only in case
nand_scan_ident() have not done it. nand_scan_ident() fills ECC
configuration from device tree.
Fixes usage of NAND_ECC_SOFT_BCH when it is specified in device tree.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This allows boards to specify NAND settings via standard DT properties.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When env support is disabled then usage of env_get_f() generates linker
errors. So do not compile env_get_f() when env support is disabled (for
example when disabled only in SPL).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When CONFIG_LOGLEVEL is set to LOGL_DEBUG or higher then linker throws
error about undefined symbol mmc_mode_name(). So compile mmc_mode_name()
also when CONFIG_LOGLEVEL is set to LOGL_DEBUG or higher.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
If env is stored on SD card then U-Boot SPL automatically calls mmc_init()
before it is going to load proper U-Boot from SD card.
If env is not stored on SD card then U-Boot SPL fails to read proper U-Boot
from SD card due to missing mmc_init() call.
So add missing mmc_init() call into fsl_esdhc_spl's mmc_boot() function.
It fixes booting from SD card on P2020 boards without env support in SPL.
mmc_init() returns early if card was already initialized, so there is no
issue with calling this function more times.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In pre-PBL header is stored size of code which BootROM copies from SD card
to L2/SRAM. This size has upper limit of L2 cache size. In most cases this
is size of U-Boot SPL or size of L2 cache.
Therefore this size in pre-PBL header cannot be used for determining size
of proper U-Boot.
So always use CONFIG_SYS_MMC_U_BOOT_SIZE for determining size of proper
U-Boot which stored on SD card.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Pre-PBL BootROMs (MPC8536E, MPC8569E, P2020, P1011, P1012, P1013, P1020,
P1021, P1022) require custom BOOT signature on sector 0 and MBR/DBR
signature is not required at all.
So add check for BOOT signature and remove check for MBR/DBR.
This allows U-Boot SPL to load proper U-Boot on pre-PBL BootROMs platforms
also from SD cards which do not have MBR/DBR signature on sector 0.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Use the spi_mem_default_supports_op() core helper in order to take into
account the buswidth specified by the user in device tree.
Fixes: 24c8ff4684 ("spi: Add Atmel QuadSPI driver")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
This commit allows the ATMEL_PIT_TIMER driver to be unselected in SPL and be
selected in u-boot proper. The SPL can use a different timer.
By having a separate Kconfig for ATMEL_TCB in SPL, the size of the SPL
decreases by 0.3 KBytes.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
This commit allows the ATMEL_TCB driver to be unselected in SPL and be
selected in u-boot proper. The SPL can use a different timer.
By having a separate Kconfig for ATMEL_TCB in SPL, the size of the SPL
decreases by 1 KByte.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
As removal of nds32 has been ack'd for the Linux kernel, remove support
here as well.
Cc: Rick Chen <rick@andestech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
To quote the author:
The bootflow feature provide a built-in way for U-Boot to automatically
boot an Operating System without custom scripting and other customisation.
This is called 'standard boot' since it provides a standard way for
U-Boot to boot a distro, without scripting.
It introduces the following concepts:
- bootdev - a device which can hold a distro
- bootmeth - a method to scan a bootdev to find bootflows (owned by
U-Boot)
- bootflow - a description of how to boot (owned by the distro)
This series provides an implementation of these, enabled to scan for
bootflows from MMC, USB and Ethernet. It supports the existing distro
boot as well as the EFI loader flow (bootefi/bootmgr). It works
similiarly to the existing script-based approach, but is native to
U-Boot.
With this we can boot on a Raspberry Pi 3 with just one command:
bootflow scan -lb
which means to scan, listing (-l) each bootflow and trying to boot each
one (-b). The final patch shows this.
With a standard way to identify boot devices, booting become easier. It
also should be possible to support U-Boot scripts, for backwards
compatibility only.
...
The design is described in these two documents:
https://drive.google.com/file/d/1ggW0KJpUOR__vBkj3l61L2dav4ZkNC12/view?usp=sharinghttps://drive.google.com/file/d/1kTrflO9vvGlKp-ZH_jlgb9TY3WYG6FF9/view?usp=sharing
Add a bootdev driver for USB host. It can use the distro boot mechanism to
locate a file, or any other available bootmeth.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a bootdev driver for MMC. It mostly just calls the bootdev helper
function.
Add a function to obtain the block device for an MMC controller.
Fix up the comment for mmc_get_blk_desc() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases two devices are related and the only way to tell is to
check that the names partially patch. Add a way to check this without
needing to create a new string for the comparison.
Fix the comment for device_find_child_by_namelen() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
It seems that namelen is more common in U-Boot. Rename this function to
fit in better. Also fix a bug where it breaks the operation of
uclass_get_by_name() and add a test.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reported-by: Tim Harvey <tharvey@gateworks.com>
Add support for the SARADC variant found on the AXG SoCs family.
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220424082159.757622-5-adeep@lexina.in
Update the clk-g12a-ao driver from "axg" to "g12a"
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220424082159.757622-3-adeep@lexina.in
Add minimal driver AO clocks on meson AXG family. Only ADC related clocks
are supported.
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220424082159.757622-2-adeep@lexina.in
Now that all the block device drivers have enable a probe hook, we will
call part_create_block_devices() to enumerate all the partitions and
create associated udevices when a block device is detected.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
ENOMEM is a more common error code for memory starvation.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
If dev_count_phandle_with_args returns 0 or another error, then pd will never
have been initialized by power_domain_get_by_index. Avoid comparing against
pd.dev in this situation.
Fixes: 3e4fcfa4bc ("power-domain: fix hang in endless loop on i.MX8")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
When usb3-phy label is found, PHY driver is called and serdes line is
initialized. This is preparation for serdes/psgtr driver to configure GT
lines based on description in DT.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add watchdog controller driver for NPCM7xx/npcm8xx
the wdt design of npcm750 and npcm845 is the same.
so the driver can work on npcm750 and npcm845.
about npcm845 wdt dtsi i will followed kernel dts name
to use nuvoton,npcm750-wdt.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
ATSHA204A uses bit-reversed checksum of standard CRC-16 with polynomial
x^16 + x^15 + x^2 + 1.
This ATSHA204A specific checksum can be calculated just by using common
U-Boot functions bitrev16() and crc16().
So replace custom driver CRC-16 implementation by common U-Boot functions.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
There are no users of the imx6_pcie_toggle_power and imx6_pcie_toggle_reset
weak overrides and as these functions are able to be handled now via dt
properties lets remove these.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
If vpcie-supply is defined by device-tree use that if
CONFIG_PCIE_IMX_POWER_GPIO is not defined.
Note that after this the following boards which define
CONFIG_PCIE_IMX_POWER_GPIO in their board header file as well as their
device-tree should be able to remove CONFIG_PCIE_IMX_PERST_GPIO without
consequence:
- mx6sabresd
- mx6sxsabresd
- novena
Note that the ge_bx50v3 board uses CONFIG_PCIE_IMX_POWER_GPIO and does
not have vpcie-supply defined in it's pcie node in the dt thus removing
CONFIG_PCIE_IMX_POWER_GPIO globally can't be done until that board adds
vpcie-supply.
Cc: Ian Ray <ian.ray@ge.com> (maintainer:GE BX50V3 BOARD)
Cc: Sebastian Reichel <sebastian.reichel@collabora.com> (maintainer:GE BX50V3 BOARD)
Cc: Fabio Estevam <festevam@gmail.com> (maintainer:MX6SABRESD BOARD)
Cc: Marek Vasut <marex@denx.de> (maintainer:NOVENA BOARD)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The i.MX8MP glue needs to be configured based on a couple of DT
properties, implement .glue_configure callback to parse those DT
properties and configure the glue accordingly.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Rename the select_dr_mode callback to glue_configure, the callback is
used for more than enforcing controller mode even on the TI chips, so
change the name to a more generic one. No functional change.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add trivial driver for i.MX8MP HSIOMIX handling. This is responsible
for enabling the GPCv2 power domains and clock for USB 3.0 and PCIe
in the correct order. Currently supported is the USB 3.0 part which
can be tested, PCIe support should be easy to add.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add i.MX8MP power domain handling into the driver. This is based on the
Linux GPCv2 driver state which is soon to be in Linux next.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Implement power_domain_get_by_name() convenience function which parses
DT property 'power-domain-names' and looks up power domain by matching
name.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Simon Glass <sjg@chromium.org>
This driver is the only SMCCC dependency in iMX8M U-Boot port. Rework
the driver based on Linux GPCv2 driver to directly control the GPCv2
block instead of using SMCCC calls. This way, U-Boot can operate the
i.MX8M power domains without depending on anything else.
This is losely based on Linux GPCv2 driver. The GPU, VPU, MIPI power
domains are not supported to save space, since they are not useful in
the bootloader. The only domains kept are ones for HSIO, PCIe, USB.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-defconfig
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The arch/arm/include/asm/arch-imx8m/power-domain.h is not included
anywhere except in drivers/power/domain/imx8m-power-domain.c, just
inline the content and drop the header. No functional change.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-defconfig
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
In case the power domain node structure is gpc@303a0000/pgc/power-domain@N,
do not bind power domain driver to the 'pgc' node, but rather descend into
it and only bind power domain drivers to power-domain@N subnodes. This way
we do not waste one useless driver instance associated with 'pgc' node.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-defconfig
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
In case the ops is not implemented, return 0 in the core right away.
This is better than having multiple copies of functions which just
return 0 in each power domain driver. Drop all those empty functions.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Simon Glass <sjg@chromium.org>
Add support for handling SFP TX disable for MVNETA in the same fashion as
to what MVPP2 is doing in order to enable using SFP-s.
This allows using ethernet on SFP only boards.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Allow device tree to provide ti,ddr-freq0 to be used as the initial DDR
frequency that is set for lpddr4 before initialization of the
controller. Make this optional and continue to use PLL bypass frequency
as is done currently if ti,ddr-freq0 is not provided.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
The k3-ddrss driver wants to configure the DDRSS_V2A_CTL_REG to reflect
the maximum possible SDRAM of 2 GB for AM64x (instead of the register's
default that says 8 GB, which the AM64x DDR controller wouldn't support).
The offset 0x20 was correct, but the register name DDRSS_V2A_R1_MAT_REG
was that of the next register at offset 0x24.
Signed-off-by: Dominic Rath <rath@ibv-augsburg.net>
The offset of the current read back register is the value of the gpio pin,
not the value written for the gpio output.
This patch fix it to avoid the other gpio output value controlled by the
same register being set incorrectly.
Fixes: 7ad889b0f3 ("gpio: Add Aspeed GPIO driver")
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
When every member of a linker list is aligned by the compiler, we can no
longer rely on the sizeof of the struct to determine the number of
entries.
For example, if the struct size is 0x90 but every entry is aligned to 0xa0
by the compiler, the linker list entries takes more space in memory and
the calculation of the number of entries is incorrect. For example, we may
see 0x12 entries when there are only 0x11.
This is a real problem. There may be a general solution, although I cannot
currently think of one. So far it only bites with OF_PLATDATA_RT which
creates a pointer to each entry of the 'struct udevice' linker_list. This
does not happen without that option, so it only affects SPL.
Work around it by manually calculating the aligned size of struct udevice,
then using that for the n_ent calculation.
Note: the alignment fix to linker list was here:
0b2fa98aa5 linker_lists: Fix alignment issue
Signed-off-by: Simon Glass <sjg@chromium.org>
At present if devres is enabled in U-Boot proper it is enabled in SPL.
We don't normally want it there, so disable it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Angus Ainslie <angus@akkea.ca>
The rk3288/RK3399 DT synced from Linux contains some different
compatible strings in the mipi node then origanal used in U-boot.
Allow both options to be backwards compatible and to be able
to handle recent rk3288.dtsi and rk3399.dtsi files.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The rk3288 DT synced from Linux contains some different
properties in the edp node then origanal used in U-boot.
Allow both options to be backwards compatible and to be able
to handle recent rk3288.dtsi files.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add driver supporting pin multiplexing on rk3066 platform.
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the clock driver for the rk3066 platform.
Derived from the rk3288 and rk3188 driver it
supports only a bare minimum to bring up the system
to reduce the TPL size for:
SDRAM clock configuration.
The boot devices NAND, EMMC, SDMMC, SPI.
A UART for the debug messages (fixed) at 115200n8.
A SARADC for the recovery button.
A TIMER for the delays (fixed).
There's support for two possible frequencies,
the safe 600MHz which will work with default pmic settings and
will be set to get away from the 24MHz default and
the maximum of 1.416Ghz, which boards can set if they
were able to get pmic support for it.
After the clock tree is set during the TPL probe
there's no parent update support.
In OF_REAL mode the drivers ns16550.c and dw-apb-timer.c
obtain the (fixed) clk_get_rate from the clock driver
instead of platdata.
The rk3066 cru node has a number of assigned-clocks properties
that call the .set_rate() function. Add them to the list so that
they return a 0 instead of -ENOENT.
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The serial_rockchip.c driver converts platdata to the data structure
used in the ns16550.c file and then calls the function
ns16550_serial_probe().
When compiled with OF_REAL the serial_rockchip.c driver returns
now -ENODEV when probed and does no harm.
The config ROCKCHIP_SERIAL is currently depends on SPL_OF_PLATDATA.
Allow serial port use for both SPL and TPL by removing this
dependency and SPL_BUILD restriction.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Rockchip serial driver depends on an enabled NS16550 driver,
so add select SYS_NS16550 to config ROCKCHIP_SERIAL.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When a defconfig for rk3288 is compiled it gives the warning:
rockchip_rk3288_uart: Missing .compatible in
./drivers/serial/serial_rockchip.c
: WARNING: the driver rockchip_rk3288_uart
was not found in the driver list
Fix by renaming U_BOOT_DRIVER name of serial_rockchip.c
to rockchip_uart. Add rk3288 serial support with
a DM_DRIVER_ALIAS define.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Rockchip uart DT nodes have "snps,dw-apb-uart" as
fall back string. The driver ns16550.c has CONFIG_IS_ENABLED(OF_REAL)
as condition to of_match and does not copy dtplat data.
For TPL/SPL the driver serial_rockchip.c
is used. Move driver alias to correct driver.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The ns16550.c driver has the following conditions for .of_match:
CONFIG_IS_ENABLED(OF_REAL)
For Rockchip SoCs with TPL/SPL and platform data that need serial
support the serial_rockchip.c driver was made. It copies this data
and then calls ns16550_serial_probe(). With the addition of yet an other
SoC type this driver is in need for a little restyle.
Simplify struct rockchip_uart_plat and add extra SoCs with
DM_DRIVER_ALIAS(). Return -ENODEV when the ns16550.c driver
probe function is available.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Rockchip SoCs rk3066/rk3188 have MMC DT nodes
with as compatible string "rockchip,rk2928-dw-mshc".
Add OF_PLATDATA support to the existing driver with
help of a DM_DRIVER_ALIAS.
This type needs a permanent enabled fifo.
The other Rockchip SoCs always have the property
"u-boot,spl-fifo-mode" in the MMC DT nodes,
because MMC to SRAM can't do DMA.
Make this property a requirement for MMC OF_PLATDATA
structures. The property "fifo-mode" must be added
for all other compile modes.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The document rockchip-dw-mshc.yaml decribes a maximum of 4 clocks.
In the rockchip_dw_mmc driver the clock name in use was "fixed"
to "ciu" with index 1, but later reverted back to index 0.
The clock drivers can handle both, but the calling driver
should submit correct data as a standard practice.
Fix the "ciu" clock index by setting it back to 1.
clock-names:
minItems: 2
items:
- const: biu
- const: ciu
- const: ciu-drive
- const: ciu-sample
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The line with .of_to_plat in the U_BOOT_DRIVER structure
of dw-apb-timer.c is not aligned with the rest.
Add an extra TAB to fix the whitespace.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Rockchip rk3066 SoC has 3 dw-apb-timer nodes.
U-boot is compiled with OF_PLATDATA TPL/SPL options,
so add OF_PLATDATA support for the dw-apb-timer.
Also change driver name to be able to compile with
U-boot scripts. No reset OF_PLATDATA support was added,
because the rk3066 nodes don't need/have them.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the HCLK_OTG, HCLK_SFC, and SCLK_SFC clocks to px30_clk_enable.
Without this change U-Boot reports an error of "Enable
clock-controller@ff2b0000 failed" on boot when using the SFC or USB in
U-Boot.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add missing include for dm/device_compat.h. Without this include the
SFC driver fails to compile because dev_err and dev_dbg are not
defined.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Mirroring commit 97ab802aa3 ("adc: meson-saradc: add support for
getting reference voltage value") for meson-saradc, this adds support
for getting the "vref-supply" regulator and register it as the ADC's
reference voltage regulator, so clients can translate sampled ADC values
to voltage.
Signed-off-by: Peter Cai <peter@typeblog.net>
Reviewed-by: John Keeping <john@metanate.com>
Tested-by: John Keeping <john@metanate.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@vrull.eu>
Cc: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A pointer can not be negative. Use macro IS_ERR_OR_NULL() for checking.
Signed-off-by: Haolin Li <li.haolin@qq.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
- DM9000 DM support
- tftp server bug fix
- mdio ofnode support functions
- Various phy fixes and improvements.
[trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c
drivers/net/phy/phy.c include/phy.h]
It seems like there was some merge error when first cleaning up and
sharing this function. We have both an inline version of the function
in include/tables_csum.h and a non-inline version in lib/tables_csum.c.
Rework things so that we only have the non-inline version (due to number
of calls, we should not inline this).
Fixes: 1befb38b86 ("x86: Move table csum into separate file")
Fixes: 2b445e4d31 ("x86: Move table csum into separate header")
Cc: Alexander Graf <agraf@csgraf.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds an implementation of puts for DM. The implementation is not as
clean as for the non-DM puts because we have to handle non-nul-terminated
string. We also handle short writes (though these are probably very
unusual).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This adds a test to ensure that puts is equivalent to putc called in a
loop. We don't verify the contents of the message to avoid having to
record console output a second time (though that could be added in the
future). The globals are initialized to non-zero values to avoid a
warning; in particular, the character count is off-by-one (but we always
make relative measurements).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This implements puts for sandbox. It is fairly straightforward, except
that we break out the shared color printing functionality into its own
function.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A string like "test\n" would be broken up into the following sequence of
prints by _serial_puts:
puts("test\n")
putc('\r')
Although functionally this is the same as \r\n, it is not the standard
sequence and caused tests to fail. Fix this by excluding the '\n' from
the initial print. The above string will now be broken up like
puts("test")
puts("\r\n")
Since we may now need to call ops->puts twice (with the associated retry
logic), break that part of the function off into a helper.
Fixes: 7a76347189 ("serial: dm: Add support for puts")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
In case the DT LED subnode contains "default-state" property set to
either "on" or "off", probe the LED driver and configure the LED state
automatically.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Steven Lawrance <steven.lawrance@softathome.com>
[trini: Update the relevant test now that we have support]
Signed-off-by: Tom Rini <trini@konsulko.com>
The OF "label" property parsing is now handled in LED core,
drop the duplicate implementation from this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Steven Lawrance <steven.lawrance@softathome.com>
The OF "label" property parsing is now handled in LED core,
drop the duplicate implementation from this driver.
Signed-off-by: Tom Rini <trini@konsulko.com>
The OF "label" property parsing is now handled in LED core,
drop the duplicate implementation from this driver.
Signed-off-by: Tom Rini <trini@konsulko.com>
The OF "label" property parsing is now handled in LED core,
drop the duplicate implementation from this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Steven Lawrance <steven.lawrance@softathome.com>
The OF "label" property parsing is now handled in LED core,
drop the duplicate implementation from this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Steven Lawrance <steven.lawrance@softathome.com>
The OF "label" property parsing is now handled in LED core,
drop the duplicate implementation from this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Steven Lawrance <steven.lawrance@softathome.com>
The OF "label" property parsing is now handled in LED core,
drop the duplicate implementation from this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Steven Lawrance <steven.lawrance@softathome.com>
Every driver in drivers/led/ currently does some form of "label" OF
property parsing in its bind() callback. Move this label parsing to
LED core, since this "label" OF property is a generic property. This
permits code deduplication in subseuqent patches.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Steven Lawrance <steven.lawrance@softathome.com>
Callers of function atsha204a_crc16() expect to return value in host cpu
endianity. So remove cpu_to_le16() conversion.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
It is possible for power domain IDs to be great than 31. If this
happens, the PTCMD and PTSTAT registers must overflow into adjacent
corresponding PTCMD_H and PTSTAT_H registers for each. Update the driver
to account for this.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Add Kconfig entry for the DM9000 MAC.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Add support for U-Boot DM and DT probing.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Instead of reading out the entire FIFO and possibly overwriting U-Boot
memory, read out one packet per recv call, pass it to U-Boot network
stack, and repeat.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Split network handling functions into non-DM specific parts and
common code in preparation for conversion to DM.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Pass private data into IO accessors and use the base addresses of
IO and DATA window from the private data instead of using the hard
coded macros DM9000_IO/DM9000_DATA. Currently both the DM9000_IO
and DM9000_DATA are assigned to the respecive private data fields
for the non-DM case backward compatibility.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Dispose of dm9000.h because none of the function prototypes declared in
it are called anywhere in the codebase. Staticize dm9000_read_srom_word()
because it is now called only from within the dm9000 driver. Drop
dm9000_write_srom_word() because it is no longer used.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Allocate driver private data dynamically in its init function and drop
the static driver private data variable. Pass the dynamic private data
throughout the driver. This is done in preparation for DM conversion.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Rename board_info structure to dm9000_priv to make it clear what this
structure really contains, the driver private data. No functional change.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Reorder the driver functions to get rid of forward declarations.
Staticize whatever is possible. No functional change.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Fix checkpatch errors and warnings. No functional change.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Remove volatile keyword usage from arrays, they are not really volatile
in any way, so this keyword is misused here. No functional change.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Rework DM9000_DMP_PACKET() into dm9000_dump_packet() function,
this brings better type checking. No functional change.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Drop unused function dump_regs() because it is unused.
No functional change.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Rename variables to lowercase to be consistent with coding style.
No functional change.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Use standard debug() macro to print debug messages instead of
reinventing driver-specific macro again. No functional change.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Make accessor names lowercase to be consistent with coding style.
No functional change.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Change type of private struct member mdio_base from void * to
phys_addr_t. This allows us to drop 2 casts.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Fix registration of 24M and 32k clock, those got applied or rebased
incorrectly, so fill in the correct code.
Fixes: 7a2c3be95a ("clk: imx8mp: Fill in DWC3 USB, USB PHY, HSIOMIX clock")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
In Linux IMX and IMXRT use the device tree to hold the anatop address.
The anatop is used in clock drivers as it controls the internal PLLs
This will move the macro from asm/arch-imxrt to the device tree.
This presumably should also be done with the other IMX boards as well.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Add compatible string for i.MX8MP, which permits i.MX8MP to use
HS400ES mode, just like all the other i.MX8M.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Haibo Chen <haibo.chen@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The i.MX8M Mini and i.MX8M Plus flexspi IPs are compatible with one
another, however the linux kernel DT uses separate compatible string
for each SoC. Add the missing i.MX8MP compatible into this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add driver for the NXP TJA1100 and TJA1101 PHYs. These PHYs are special
BroadRReach 100BaseT1 PHYs used in automotive.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This macro currently supports only one parameter. Based on Linux iopoll,
let's extend read_poll_timeout common API to allow multiple variable
parameters.
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
This driver supports NXP C45 TJA11XX PHYs, but there're also other NXP
TJA11XX PHYs. Let's rename functions in this driver to be c45 variant
specific, so further drivers can be introduced adding support for NXP
TJA11XX PHYs.
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Separe dm implementation from non dm implementation of pwm-imx
driver using CONFIG_DM_PWM
Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
Move pwm_imx_get_parms, pwm_id_to_reg functions into pwm-imx.c
and drop off pwm-imx-util.c
Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
This commit adds the possibility to choose the compatible
"regulator-fixed-clock" in devicetree.
This is a special case of regulator-fixed where a clock has to
be used to switch the regulator on and off.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
- According to S400 API, the fuse bank 25 (Testconfig2) is able to
access. Add it into driver's mapping table.
- According to FSB words list, the reserved 48 words are ahead of
the bank 5 and bank 6. Fix the wrong position.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since latest S400 firmware has supported to read OEM SRK Hash, add
it to the driver's table
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add initial support for i.MX8MP USB PHY, i.MX8MP USB is similar to
the i.MX8MQ, except for clock and power domain design customization.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
Add clock tables required to bring up DWC3 USB, USB PHY and HSIOMIX domain.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Re-factor the imx8m[nmpq] rate tables into the common pll1416x clock
driver.
43cdaa1567ad3 ("clk: imx8mm: Move 1443X/1416X PLL clock structure to common place")
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm-beacon
This is a DM clock driver based off the imx8mm u-boot driver and the linux
kernel driver.
All of the PLLs and clocks are initialized so the subsystems below are
functional and tested.
1) USB host and peripheral
2) ECSPI
3) UART
4) I2C all busses
5) USDHC for eMMC support
6) USB storage
7) GPIO
8) DRAM
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Acked-by: Sean Anderson <seanga2@gmail.com>
The mxs_nand_spl driver can support to read from page unaligned offset,
so don't need to set bl_len to ask spl_load_simple_fit to handle
the page unaligned access.
Actually spl_load_simple_fit has two parts of reading:
spl_simple_fit_read and spl_load_fit_image.
The spl_load_fit_image can handle the page unaligned offset,
but the spl_simple_fit_read can't do it. spl_simple_fit_read requires
the FIT location at page aligned offset.
Hence, remove the nand_get_mtd overwrite function from mxs_nand_spl
to use page unaligned read by driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
Tested-by: Tim Harvey <tharvey@gateworks.com> #gw_ventana
Introduce pwm_dm_imx_get_parms, dm version of pwm_imx_get_parms.
This function get clock rate using clk dm api
Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
Get and enable ipg/per pwms clocks using dm api into imx_pwm_of_to_plat
and imx_pwm_probe driver function
Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com>
Add a driver for the Gateworks System Controller used on Gateworks boards
which provides a boot watchdog, power control, temperature monitor,
and voltage ADCs.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add entry for 3732 MT/s mode of operation of the LPDDR4, in
which case the DDR PLL has to be configured in 933 MHz mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add DT compatible string for PCA9450C PMIC. This is a variant of the
PCA9450 PMIC with 6 A dual-phase buck regulator and 3 A buck regulator,
and is software-wise compatible with the PCA9450B. This variant of the
PCA9450 is designed for use as companion PMIC for i.MX8MP.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The correct compatible string for i.MX8MP variant of DWC EQoS MAC
is "nxp,imx8mp-dwmac-eqos", use it. Drop the two current users of
the current wrong compatible string to avoid breaking them.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
i.MX8(QM/QXP) - added support for JR driver model.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
added device tree support for job ring driver.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In case mtd_info's dev field is not populated (raw nand's case),
use the flash_node new field which reference the DT flash node where
can be found "partitions" node with "fixed-partitions" compatible.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Farhan Ali <farhan.ali@broadcom.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Marek Behun <marek.behun@nic.cz>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Wolfgang Denk <wd@denx.de>
Currently, add_mtd_partitions_of() can be used only if dev field of
mtd_info struct is populated. It's the case, for example, for a spi nor
flash, which has a DT compatible "jedec,spi-nor" and an associated
device. mtd->dev is populated in spi_nor_scan().
But in case of a raw nand node, mtd_info's dev field can't be populated
as flash node has no compatible, so no associated device.
add_mtd_partitions_of() can't be used to parse "partitions" subnode.
To remove this constraint, add an ofnode field in mtd_info struct
which reference the DT flash node. This new field is populated by
nand_scan_tail(). This new field will be used by add_mtd_partitions_of()
to parse the flash node for "partitions" defined in DT.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Farhan Ali <farhan.ali@broadcom.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Marek Behun <marek.behun@nic.cz>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Wolfgang Denk <wd@denx.de>
When probing the LEDs, a default brightness is set based on settings
from the U-Boot device tree, i.e. the 'default-brightness' property
of the LED nodes. If that property is not present, the default
maximum brightness is set.
This should make sure the LED controller's registers affecting the
brightness are correctly initialized and should give a consistent
behaviour.
Signed-off-by: Paul HENRYS <paul.henrys_ext@softathome.com>
Add a driver which allows to use of LEDs connected
to PWM (Linux compatible).
MAINTAINERS: add i.vozvakhov as a maintainer of leds-pwm
C(required during new functionality adding).
Signed-off-by: Ivan Vozvakhov <i.vozvakhov@corp.mail.ru>
In U-Boot, the discovery of TA based on its UUID on the TEE bus is
not supported.
This patch only binds the driver associated to the new supported
OP-TEE TA = TA_HWRNG when this driver is enable.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add driver for OP-TEE based Random Number Generator on ARM SoCs
where hardware entropy sources are not accessible to normal world
and the RNG service is provided by a HWRNG Trusted Application (TA).
This driver is based on the linux driver: char/hw_random/optee-rng.c
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Documentation:
* Describe how enable DM_SERIAL for a board
UEFI
* Preparatory patches for better integration of DM and UEFI
* Use sysreset after capsule updates instead of do_reset
* Allow to disable persisting non-volatile variables
-----BEGIN PGP SIGNATURE-----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=SxkC
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-07-rc1' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-07-rc1
Documentation:
* Describe how enable DM_SERIAL for a board
UEFI
* Preparatory patches for better integration of DM and UEFI
* Use sysreset after capsule updates instead of do_reset
* Allow to disable persisting non-volatile variables
When gpio_request_by_name allocates a gpio output it by default will
de-assert the gpio which for phy-reset will take the PHY out of reset.
As this occurs before eth_phy_reset is called to assert the reset
line it can cause undesired affects if reset timings are not properly
met.
Configure the gpio with GPIOD_IS_OUT_ACTIVE so that reset is kept active
(reset asserted) to avoid this.
Cc: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
When gpio_request_by_name allocates a gpio output it by default will
de-assert the gpio which for phy-reset will take the PHY out of reset.
As this occurs before fec_gpio_reset is called to assert the reset
line it can cause undesired affects if reset timings are not properly
met.
Configure the gpio with GPIOD_IS_OUT_ACTIVE so that reset is kept active
(reset asserted) to avoid this.
Cc: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm-beacon
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Currently we require PHY interface mode to be known when
finding/creating the PHY - the functions
* phy_connect_phy_id()
* phy_device_create()
* create_phy_by_mask()
* search_for_existing_phy()
* get_phy_device_by_mask()
* phy_find_by_mask()
all require the interface parameter, but the only thing done with it is
that it is assigned to phydev->interface.
This makes it impossible to find a PHY device without overwriting the
set mode.
Since the interface mode is not used during .probe() and should be used
at first in .config(), drop the interface parameter from these
functions. Make the default value of phydev->interface (in
phy_device_create()) to be PHY_INTERFACE_MODE_NA. Move the interface
parameter to phy_connect_dev(), where it should be.
Change all occurrences treewide. In occurrences where we don't call
phy_connect_dev() for some reason (they only configure the PHY without
connecting it to an ethernet controller), set
phydev->interface = value from phy_find_by_mask call.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
The bcmgenet and sun8i_emac drivers call phy_connect(), which finds /
creates the PHY and also connects it to the eth device via
phy_connect_dev(), then set some phydev members (bcmgenet only), and
then call phy_connect_dev() explicitly again.
Drop the second phy_connect_dev(), since it is unnecesary.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Use phydev->is_c45 instead of is_10g_interface(phydev->interface) to
determine whether clause 45 protocol should be used.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
We want to be able to have phydev->interface uninitialized during
->probe(). We should assume that phydev->interface is initialized only
before ->config().
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Rename constant PHY_INTERFACE_MODE_NONE to PHY_INTERFACE_MODE_NA to make
it compatible with Linux' naming.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Rename constant PHY_INTERFACE_MODE_COUNT to PHY_INTERFACE_MODE_MAX to
make it compatible with Linux' naming.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Add helpers ofnode_read_phy_mode() and dev_read_phy_mode() to parse the
"phy-mode" / "phy-connection-type" property. Add corresponding UT test.
Use them treewide.
This allows us to inline the phy_get_interface_by_name() into
ofnode_read_phy_mode(), since the former is not used anymore.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
The "phy-interface-type" property should be "phy-connection-type".
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Use the new dm_mdio_read/write/reset() wrappers treewide, instead of
always getting and dereferencing MDIO operations structure pointer.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Add helpers ofnode_get_phy_node() and dev_get_phy_node() and use it in
net/mdio-uclass.c function dm_eth_connect_phy_handle(). Also add
corresponding UT test.
This is useful because other part's of U-Boot may want to get PHY ofnode
without connecting a PHY.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The type of the return value of phy_read() and phy_read_mmd() is int.
Change the variable to not be unsigned so that we not get into an
unsigned compared against 0.
Signed-off-by: Haolin Li <li.haolin@qq.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
A DM_ETH driver may use phy_connect() towards a PHY address on an MDIO
bus which is not specified in the device tree, as evidenced by:
pfe_eth_probe
-> pfe_phy_configure
-> phy_connect
When this happens, the PHY will have an invalid OF node.
When ar803x_config() runs, it silently fails at ar803x_of_init(), and
therefore, fails to run the rest of the initialization.
This makes MII_BMCR contain what it had after BMCR_RESET (0x8000) has
been written into it by phy_reset(). Since BMCR_RESET is volatile and
self-clearing, the MII_BMCR ends up having a value of 0x0. The further
configuration of this register, which is supposed to be handled by
genphy_config_aneg() lower in ar803x_config(), never gets a chance to
run due to this early error from ar803x_of_init().
As a result of having MII_BMCR as 0, the following symptom appears:
=> setenv ethact pfe_eth0
=> setenv ipaddr 10.0.0.1
=> ping 10.0.0.2
pfe_eth0 Waiting for PHY auto negotiation to complete......... TIMEOUT !
Could not initialize PHY pfe_eth0
Manually writing 0x1140 into register 0 of the PHY makes the connection
work, but it is rather desirable that the port works without any manual
intervention.
Fixes: fe6293a809 ("phy: atheros: add device tree bindings and config")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
A DM_ETH driver may use phy_connect() towards a PHY address on an MDIO
bus which is not specified in the device tree, as evidenced by:
pfe_eth_probe
-> pfe_phy_configure
-> phy_connect
When this happens, the PHY will have an invalid OF node.
The dp83867_config() method has extra initialization steps which are
bypassed when the PHY lacks an OF node, which is undesirable because it
will lead to broken networking. Allow the rest of the code to run.
Fixes: 085445ca41 ("net: phy: ti: Allow the driver to be more configurable")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
With dm-tag feature, any U-Boot subsystem is allowed to associate
arbitrary number of data with a particular udevice. This can been
see as expanding "struct udevice" without modifying the definition.
As a first user, UEFI subsystem makes use of tags to associate
an efi_disk object with a block device.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Every time an ide bus/port is scanned and a new device is detected,
we want to call device_probe() as it will give us a chance to run
additional post-processings for some purposes.
In particular, support for creating partitions on a device will be added.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Every time a sata bus/port is scanned and a new device is detected,
we want to call device_probe() as it will give us a chance to run
additional post-processings for some purposes.
In particular, support for creating partitions on a device will be added.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Every time a nvme bus/port is scanned and a new device is detected,
we want to call device_probe() as it will give us a chance to run
additional post-processings for some purposes.
In particular, support for creating partitions on a device will be added.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Every time a mmc bus/port is scanned and a new device is detected,
we want to call device_probe() as it will give us a chance to run
additional post-processings for some purposes.
In particular, support for creating partitions on a device will be added.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Every time a scsi bus/port is scanned and a new block device is detected,
we want to call device_probe() as it will give us a chance to run
additional post-processings for some purposes.
In particular, support for creating partitions on a device will be added.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Take as reference Linux kernel code:
drivers/gpio/gpio-pca953x.c
Signed-off-by: Luca Ellero <l.ellero@asem.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use the CONFIG macros to conditionally build the GPIO hogging support in
either the SPL or U-Boot, or both, depending on the configuration. Also
call the GPIO hog probe function in the common SPL board initialization
as an equivalent to adding it to the U-Boot init sequence functions.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for the upstream gpio-line-names property already described
in the common GPIO binding document[1]. The ability to search for a line
name allows boards to lift the implementation of common GPIO behaviours
away from specific line indexes on a GPIO controller.
[1] 3c35bfee83/dtschema/schemas/gpio/gpio.yaml (L17)
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
This is a little tricky since SoCFPGA has code to determine this as
runtime. Introduce a guard variable for platforms to select if they
have a static value to use. Then for ARCH_SOCFPGA, call
cm_get_qspi_controller_clk_hz() and otherwise continue the previous
behavior.
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CONS_SCIF0
CONFIG_CONS_SCIF1
CONFIG_CONS_SCIF2
CONFIG_CONS_SCIF4
CONFIG_CONS_SCIFA0
Signed-off-by: Tom Rini <trini@konsulko.com>
