We move all IO addressed (CCSR, localbus, PCI) above the 4G boundary
to allow for larger memory sizes.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The old PCI ATMU setup code would just mimic the PCI regions into the
ATMU registers. For simple memory maps in which all memory, MMIO, etc
space fit into 4G this works ok. However there are issues with we have
>4G of memory as we know can't access all of memory and we need to
ensure that PCICSRBAR (PEXCSRBAR on PCIe) isn't overlapping with
anything since we can't turn it off.
We first setup outbound windows based on what the board code setup
in the pci regions for MMIO and IO access. Next we place PCICSRBAR
below the MMIO window. After which we try to setup the inbound windows
to map as much of memory as possible.
On PCIe based controllers we are able to overmap the ATMU setup since
RX & TX links are separate but report the proper amount of inbound
address space to the region tracking to ensure there is no overlap.
On PCI based controllers we use as many inbound windows as available to
map as much of the memory as possible.
Additionally we changed all the CCSR register access to use proper IO
accessor functions. Also had to add CONFIG_SYS_CCSRBAR_PHYS to some
86xx platforms that didn't have it defined.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
apparently the ITX was missed last round.
Also make bootdelay consistent with other boards, so as to give on the
opportunity to fix mistakenly set bootcmd without having checked for an
bootdelay zero setting first.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
All in-tree boards that use this controller have CONFIG_NET_MULTI added
Also:
- changed CONFIG_DRIVER_CS8900 to CONFIG_CS8900
- changed CS8900_BASE to CONFIG_CS8900_BASE
- changed CS8900_BUS?? to CONFIG_CS8900_BUS??
- cleaned up line lengths
- modified VCMA9 command function that accesses the device
- removed MAC address initialization from lib_arm/board.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Tested-by: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
This chooses 4kB data size for both TFTP and NFS, as an example
about how to use support for IP fragments.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Add support for the DEKA Research and Development galaxy5200 board
The galaxy5200 is an Freescale mpc5200 based embedded industrial
control board.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Some boards have fallen out of sync by defining CONFIG_ENV_IS_EMBEDDED
manually. While it is useful to have this available to the build system,
let's do it automatically rather than forcing people to opt into it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Newer revisions of these boards have slightly larger flashes, so increase
the configured number of sectors so that U-Boot works on all revisions.
Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
linux mpc83xx_defconfig kernels are getting bigger, accommodate for
their growth by adjusting default load and fdt addresses.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
when using Linus' 83xx_defconfig, the mpc8377rdb would hang at boot
at either:
NET: Registered protocol family 16
or the
io scheduler cfq registered
message. Fixing up these DDR settings appears to fix the problem.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 9993e196da "mpc83xx: convert all
remaining boards over to 83XX_GENERIC_PCI" remapped pci windows on
tqm834x to make it more consistent with the other 83xx boards. During
that time however, the author failed to realize that FLASH_BASE was
occupying the same range as what PCI1_MEM_BASE was being assigned.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Tested-by: Wolfgang Denk <wd@denx.de>
This was introduced with the MPC8349EMDS board, and then copied to
a couple other boards by nature of being the reference implementation.
u-boot$git grep CONFIG_SYS_MID_FLASH_JUMP
include/configs/MPC8349EMDS.h:#define CONFIG_SYS_MID_FLASH_JUMP 0x7F000000
include/configs/sbc8349.h:#define CONFIG_SYS_MID_FLASH_JUMP 0x7F000000
include/configs/vme8349.h:#define CONFIG_SYS_MID_FLASH_JUMP 0x7F000000
u-boot$
It currently isn't used, so delete it before it spreads further.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Prior to this commit, to enable PCI, you had to go manually
edit the board config header, which isn't really user friendly.
This adds the typical PCI make targets to the toplevel Makefile
in accordance with what is being done with other boards.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
It is recommended to define the macro CONFIG_SYS_64BIT_VSPRINTF
for NAND specific warning removal, same is done in this patch
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
The name of the atmel nand driver in the kernel changed from at91_nand
to atmel_nand back in June 2008, but the at91-based boards config files
still refer to at91_nand. This patch updates them with the new name
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
This patch fixes the "chip_config" command for I2C bootstrap EEPROM
configuration. First it changes the I2C bootstrap EEPROM address to
0x54 as this is used on Arches (instead of 0x52 on Canyonlands/
Glacier). Additionally, the NAND bootstrap settings are removed
for Arches since Arches doesn't support NAND-booting.
Signed-off-by: Stefan Roese <sr@denx.de>
For some reason the MPC8544 enabled BEDBUG if PCI was enabled and that
got copied int the MPC8536, MPC8572 and P2020 DS boards. The BEDBUG
support has never been made to work completely on e500/85xx so we
just disable it to save space and match the other FSL 85xx boards.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It is recommended to define the macro CONFIG_SYS_64BIT_VSPRINTF
for NAND specific warning removal, same is done in this patch
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Embedd chip select configuration into struct for gpmc config
instead of having it completely separated as suggested by
Wolfgang Denk on
http://lists.denx.de/pipermail/u-boot/2009-May/052247.html
Signed-off-by: Matthias Ludwig <mludwig@ultratronik.de>
For some reason the AT91rm9200 lowlevel init writes to a bunch of
reserved or read-only addresses. All the boards seem to define the
value-to-be-written values as zero ... but they shouldn't actually
be writing *anything* there.
No documented erratum justifies these accesses. It looks like maybe
some pre-release BDI-2000 setup code has been carried along by cargo
cult programming since at least late 2004 (per GIT history).
Here's a patch disabling what seems to be bogosity. Tested on a
csb337; there were no behavioral changes.
Signed-off-by: David Brownell <david-b@pacbell.net>
on RM9200ek
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch moves the load addresses for kernel, fdt and ramdisk to higher
addresses (>= 16MB). This enables booting of bigger kernel images (e.g.
lockdep enabled).
Signed-off-by: Stefan Roese <sr@denx.de>
This patch changes CONFIG_SYS_BOOTMAPSZ from 8MB to 16MB which is the
initial TLB on 40x PPC's in the Linux kernel. With this change even bigger
Linux kernels (> 8MB) can be booted.
This patch also sets CONFIG_SYS_BOOTM_LEN to 16MB (default 8MB) to enable
decompression of bigger images.
Signed-off-by: Stefan Roese <sr@denx.de>
Because twl4030 now has its own device files, move and rename
twl4030_mmc_config.
twl4030_mmc_config initializes the twl4030 power setting to
the mmc device. Because it is in the twl4030 power domain, move
it out of drivers/mmc/omap3_mmc.c and into drivers/power/twl4030.c.
The function was renamed to twl4030_power_mmc_init because all
the functions in this file are to have the format
twl4030_power_<device>_<action>
In this case the suffix is mmc_init so
device : mmc
action : init
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
Because twl4030 now has its own device files, move exiting
omap3 power_init_r to a new location.
power_init_r is the only function in board/omap3/common.
It initializes the twl4030 power for the board and enables
the led.
The power part of the the function is moved to twl4030_power_init in
drivers/power/twl4030.c The power compilation is conditional on the
existing config variable CONFIG_TWL4030_POWER.
The led part is moved to twl4030_led_init in the new file
drivers/misc/twl4030_led.c The led compilation is conditional on
the new config variable CONFIG_TWL4030_LED
The directory board/omap3/common was removed because power_init_r
was the only function in it.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
Commit 2b3f12c2 added support for configurable SMC Rx buffer length on
8xx systems. Enable this feature on TQM8xx* based boards.
This fixes the problem that pasting text in the middle of a line
(i. e. inserting in edit mode) did not work - only the first two
characters got inserted, the rest was lost.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The Zoom2 power reset button is on the top right side of the
main board. Press and hold for about to 8 seconds to completely
reset the board.
Some of the beta boards have a hardware problem that prevents
using this feature. If is difficult to further characterize the
boards that fail. So disable resetting for all beta boards.
The Zoom1 reset button is the red circle on the top right,
front of the board. Press and hold the button for 8 seconds to
completely reset the board.
After analyzing beagle, it was determined that other boards
that use the twl4030 for power managment can also make use
this function.
The resetting is done by the power management part of the twl4030.
Since there is no existing drivers/power, add one.
The compilation of power/twl4030.h is controlled by the config
variable CONFIG_TWL4030_POWER
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
DDR2 Auto-calibration needs to be disabled on the NAND booting PPC4xx
targets. Otherwise the configured fixed init values for some DDR2
controller registers (e.g. RQDC) are not initialized at all resulting
in a non working SDRAM.
Signed-off-by: Stefan Roese <sr@denx.de>
Board support for the Guntermann & Drunck CompactCenter and
DevCon-Center.
Based on the AMCC Canyonlands board support by Stefan Roese.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for the esd VME8349 board equipped with the
MPC8349. It's a VME PMC carrier board equipped with the Tundra
TSI148 VME-bridge.
Signed-off-by: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Up to this point in time, the sbc8349 board was storing the u-boot
image in flash 2x. One for the HRCW value at the beginning of
flash (0xff80_0000), and once close to the end of flash (0xfff8_0000)
for the actual image that got executed.
This moves the TEXT_BASE to be the beginning of flash, which makes
the second copy of the image redundant, and frees up the flash
from the end of the environment storage to the end of the flash
device itself.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Commit 7024aa14 was supposed to fix the #ifdef/#endif pairing in
include/configs/at91cap9adk.h, but did not cate all problems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch updates the support for EB+MCF-EV123 board and needs
the [PATCH 1/2 V3] new video driver for bus vcxk framebuffers
* remove the board framebuffer driver
* use the common bus_vcxk framebuffer driver
* adds bmp support
* adds splashimage support
* fix serveral cosmetical errors
Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
[agust@denx.de: fixed some style issues before applying]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This patch removes the "alterpll" command and replaces it with the now
ppc4xx standard "chip_config" command to configure the I2C bootstrap
EEPROM.
Signed-off-by: Stefan Roese <sr@denx.de>
Kilauea has an AT24C02 EEPROM which has an 8 byte page. Without defining
CONFIG_SYS_EEPROM_PAGE_WRITE_BITS to 3 the "eeprom" command doesn't
work correctly.
Additionally the page write delay (CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS)
is set to a more defensive value of 10ms.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds a generic command for programming I2C bootstrap
eeproms on PPC4xx. An implementation for Canyonlands board is
included.
The command name is intentionally chosen not to be PPC4xx specific.
This way other CPU's/SoC's can implement a similar command under
the same name, perhaps with a different syntax.
Usage on Canyonlands:
=> chip_config
Available configurations (I2C address 0x52):
600-nor - NOR CPU: 600 PLB: 200 OPB: 100 EBC: 100
600-nand - NAND CPU: 600 PLB: 200 OPB: 100 EBC: 100
800-nor - NOR CPU: 800 PLB: 200 OPB: 100 EBC: 100
800-nand - NAND CPU: 800 PLB: 200 OPB: 100 EBC: 100
1000-nor - NOR CPU:1000 PLB: 200 OPB: 100 EBC: 100
1000-nand - NAND CPU:1000 PLB: 200 OPB: 100 EBC: 100
1066-nor - NOR CPU:1066 PLB: 266 OPB: 88 EBC: 88 ***
1066-nand - NAND CPU:1066 PLB: 266 OPB: 88 EBC: 88
=> chip_config 600-nor
Using configuration:
600-nor - NOR CPU: 600 PLB: 200 OPB: 100 EBC: 100
done (dump via 'i2c md 52 0.1 10')
Reset the board for the changes to take effect
Other 4xx boards will be migrated to use this command soon
as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
The XPedite1000 is an X-ES product thus it can be put in board/xes along
with other X-ES boards. Along with the move, the board was renamed to
XPedite1000 from XPedite1K to fit X-ES's standard naming convention.
Maintainership was also transfered to Peter Tyser.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The XPedite1000 only has 2 available ethernet ports:
ppc_4xx_eth2 (EMAC2) and ppc_4xx_eth3 (EMAC3)
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Previously an I2C EEPROM was used. The EEPROM had size, reliability,
and access issues which are resolved by storing the environment in
flash.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The XPedite1000 can be built with 4 total flashes:
- 512KB AMD socketed
- 16MB Intel soldered
- 2 x 32MB AMD MirrorBit flashes
Add support for the optional 2 32MB CFI-compliant AMD flashes
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
By default, the XPedite1000 comes installed with xMon, a proprietary
bootloader. xMon stores its MAC address in an onboard EEPROM. Rather
than requiring a non-standard location in the EEPROM to be reserved for
MAC addresses, store the MAC addresses in U-Boot's standard environment.
A U-Boot application or OS application can be used to migrate xMon MAC
addresses to U-Boot's environment if necessary.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Using the CFI flash driver will allow write access to the 16MB Intel
StrataFlash present on the XPedite1000. The 512KB socketed (non
CFI-compliant flash) will no longer be writable.
The mapping of the 16MB Strata flash was moved to 0xff000000 and the
512KB AMD socketed flash was moved to 0xfe000000.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds I2C support for mvBC-P and defines flash layout
matching the shipped product.
Signed-off-by: Andr Schwarz <andre.schwarz@matrix-vision.de>
All in-tree boards that use this controller have CONFIG_NET_MULTI added
Also:
- changed CONFIG_DRIVER_SMC911X* to CONFIG_SMC911X*
- cleaned up line lengths
- modified all boards that override weak function in this driver
- added
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Tested-by: Mike Frysinger <vapier@gentoo.org>
This is Marvell's 88F6281_A0 based reference design board
This patch is tested for-
1. Boot from DRAM/NAND flash/NFS
2. File transfer using tftp and loadb
3. NAND flash read/write/erase
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Use the MPC8572's eLBC to access 1 GB (or greater) onboard NAND flash
via the 'nand' command.
Previously, the XPedite5370's NAND chip selects were properly
configured, but NAND support was not enabled.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Increasing CONFIG_SYS_BOOTM_LEN from 8 MB to 16 MB is necessary to
support uncompressing images larger than 8 MB when using the bootm
command.
Note that recent Linux kernels for the 85xx and 86xx map greater than
16MB of memory on bootup, but we use 16MB to maintain compatibility with
older Linux kernels for now.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Buffered writes are possible on the XPedite5200 and XPedite5370 and greatly
improve NOR flash write speeds
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The p2020DS, MPC8536DS, MPC8572DS, MPC8544DS boards are capable of
swizzling the upper address bits of the NOR flash we boot out of which
creates the concept of "virtual" banks. This is useful in that we can
flash a test of image of u-boot and reset to one of the virtual banks
while still maintaining a working image in "bank 0".
The PIXIS FPGA exposes registers on LBC which we can use to determine
which "bank" we are booting out of (as well as setting which bank to
boot out of).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8641HPCN board is capable of swizzling the upper address bit of
the NOR flash we boot out of which creates the concept of "virtual"
banks. This is useful in that we can flash a test of image of u-boot
and reset to one of the virtual banks while still maintaining a
working image in "bank 0".
The PIXIS FPGA exposes registers on LBC which we can use to determine
which "bank" we are booting out of (as well as setting which bank to
boot out of).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
A large number of boards (all AT91 based) duplicated the ROUND()
macro in their board specific config files. Add the definition to
include/common.h and clean up the board config files.
Signed-off-by: Wolfgang Denk <wd@denx.de>
We have always mapped at least 16M in the kernel and we have seen cases
with new kernel features that a kernel image needs more than 8M of
memory.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CONFIG_SYS_MALLOC_LEN is defined in the board config, and
the keymile-common.h, which collects common options used
by all keymile-boards. This results in a compile error
when compiling the kmeter1 board. So remove this define
in the board config file.
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch adds the possibility to call a board specific
i2c bus reset routine for the fsl_i2c bus driver, and adds
this option for the keymile kmeter1 board.
The deblock sequence for this board is implemented and
tested in the following way:
CR = 0x20 (release SDA and SCL pin)
CR = 0xa0 (start read)
dummy read
dummy read
if 2. dummy read == 0x00
3. dummy read
CR = 0x80 (SDA and SCL now 1 SR = 0x86)
CR = 0x00 (Modul reset SR=0x81)
CR = 0x80 (SDA and SCL = 1, SR = 0x81)
Signed-off-by: Heiko Schocher <hs@denx.de>
- CONFIG_SYS_MAX_I2C_BUS changed to 1
We use only one I2C hardwarecontroller on this boards, so
change the CONFIG_SYS_MAX_I2C_BUS to 1.
- common: dont print errormsg if second IVM Block lacks.
- 82xx, mgcoge: fix double mtdpart entry in environment
- 82xx, mgcoge: activate on second Flash the second bank.
- common: CONFIG_ENV_SIZE 0x4000 for all keymile boards
- common: Change malloc size to 1MByte for all Keymile boards
We need a bigger malloc area for the environment support (128k)
on some Keymile boards (kmeter1) and the upcoming UBI support.
Change it to 1MB for all Keymile boards to be on the save side.
Also define CONFIG_SYS_64BIT_VSPRINTF which is needed for
UBI/UBIFS support.
- Add UBI support to all Keymile boards
- change manner of writing "/localbus/ranges" node
instead of writting the complete "/localbus/ranges" node
before booting Linux, only update the ranges entries
which gets dynamical detected (size of flashes).
This is needed, because keymile adds in the DTS
"/localbus/ranges" node entries, which u-boot must
not overwrite/delete.
- kmeter, mgcoge: define 2 seperate regions needed for the Intel P30 chips
The Intel P30 chip has 2 non-identical chips on
one die, so we need to define 2 seperate regions
that are scanned by physmap_of independantly.
- kmeter1: Add MTD concat support to Keymile boards
- 82xx, mgcoge: add "unlock=yes" to default environment
- added CONFIG_MTD_DEVICE to get in sync with mainline code
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Commit 2419169f removed support for legacy NAND and disk on chip but
missed to update the code for a few boards. This patch fixes the
resulting build issues.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch adds a SATA harddisk driver for the canyonlands.
This patch is kernel driver's porting.
This patch corresponded to not cmd_scsi but cmd_sata.
This patch divided an unused member with ifndef __U_BOOT__ in the structure.
[environment variable, boot script]
setenv bootargs root=/dev/sda7 rw
setenv bootargs ${bootargs} console=ttyS0,115200
ext2load sata 0:2 0x400000 /canyonlands/uImage
ext2load sata 0:2 0x800000 /canyonlands/canyonlands.dtb
fdt addr 0x800000 0x4000
bootm 0x400000 - 0x800000
If you drive SATA-2 disk on Canyonlands, you must change parts from
PI2PCIE212 to PI2PCIE2212 on U25. We confirmed to boot by using
following disks:
1.Vendor: Fujitsu Type: MHW2040BS
2.Vendor: Fujitsu Type: MHW2060BK
3.Vendor: HAGIWARA SYS-COM:HFD25S-032GT
4.Vendor: WesternDigital Type: WD3200BJKT (CONFIG_LBA48 required)
5.Vendor: WesternDigital Type: WD3200BEVT (CONFIG_LBA48 required)
6.Vendor: Hitachi Type: HTS543232L9A300 (CONFIG_LBA48 required)
7.Vendor: Seagate Type: ST31000333AS (CONFIG_LBA48 required)
8.Vendor: Transcend Type: TS32GSSD25S-M
9.Vendor: MTRON Type: MSD-SATA1525-016
Signed-off-by: Kazuaki Ichinohe <kazuichi at fsi.co.jp>
While the 1.0 and 1.2 spin of the bf533-stamp boards can handle the higher
SCLK speeds just fine, the 1.1 spin cannot due to the bugs introduced with
the shortened SDRAM traces. So lower the SCLK speed down to a value that
all three can handle.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Commit 8d2effea added a warning for configurations that use NAND
without defining the (then necessary) CONFIG_SYS_64BIT_VSPRINTF but
failed to fix the affected boards.
This patch covers the non-PPC boards that were missed in the previous
patch (commit 170c1972).
Signed-off-by: Wolfgang Denk <wd@denx.de>
This is Marvell's 88F6281_A0 based custom board developed
for wireless access point product
This patch is tested for-
1. Boot from DRAM/SPI flash/NFS
2. File transfer using tftp and loadb
3. SPI flash read/write/erase
4. Booting Linux kernel and RFS from SPI flash
5. Boot from USB supported
Reviewed-by: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Reference:
http://plugcomputer.org/http://openplug.org/plugwiki/index.php/Das_U-boot_plug_support
This patch is tested for-
1. Boot from DRAM/NAND flash
2. File transfer using tftp
3. NAND flash read/write/erase
4. Linux kernel and RFS Boot from NAND
5. Enabled USB PHY init for kernel need
6. Boot from USB supported
Note: to boot Kirkwood kernel with USB support,
you should add "usb start" in the boot sequence
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Commit 8d2effea added a warning for configurations that use NAND
without defining the (then necessary) CONFIG_SYS_64BIT_VSPRINTF but
failed to fix the affected boards.
Signed-off-by: Wolfgang Denk <wd@denx.de>
So far the console API uses the following naming convention:
======Extract======
typedef struct device_t;
int device_register (device_t * dev);
int devices_init (void);
int device_deregister(char *devname);
struct list_head* device_get_list(void);
device_t* device_get_by_name(char* name);
device_t* device_clone(device_t *dev);
=======
which is too generic and confusing.
Instead of using device_XX and device_t we change this
into stdio_XX and stdio_dev
This will also allow to add later a generic device mechanism in order
to have support for multiple devices and driver instances.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Edited commit message.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch simply converts the board to the hwconfig infrastructure.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
fdt_fixup_esdhc() will either disable or enable eSDHC nodes, and
also will fixup clock-frequency property.
Plus, since DR USB and eSDHC are mutually exclusive, we should
only configure the eSDHC if asked through hwconfig.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds support for eSDHC on MPC837XERDB boards. The WP
switch doesn't seem to work on RDB boards though, the WP pin is
always asserted (can see the pin state when it's in GPIO mode).
FSL DR USB and FSL eSDHC are mutually exclusive because of pins
multiplexing, so user should specify 'esdhc' or 'dr_usb' options
in the hwconfig environment variable to choose between the
devices.
p.s.
Now we're very close to a monitor len limit (196 bytes left using
gcc-4.2.0), so also increase the monitor len by one sector (64 KB).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Saving the environment leads to overwriting u-boot itself,
bricking boards. Increase u-boot's image size so the environment
base address doesn't end up overlapping u-boot text.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
When enabling NAND support for a board, one must also define
CONFIG_SYS_64BIT_VSPRINTF because this is needed in nand_util.c
for correct output.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Dave Liu <daveliu@freescale.com>
Cc: Ron Madrid <ron_madrid@sbcglobal.net>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Remove individual CPU specific DSPI driver.
Add required feature for the common DSPI driver in cpu_init and
in platform configuration file.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Update serial boot DRAM's Internal RAM, vector table and DRAM in
start.S, serial flash's read status command over SPI and NOR
flash.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Remove dead code that was obviously a left-over from copy & paste.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
When enabling NAND support for a board, one must also define
CONFIG_SYS_64BIT_VSPRINTF because this is needed in nand_util.c
for correct output.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a
faster clock speed: 266/133MHz.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.
The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES.
On the board you can find 2 USART, USB high speed,
a 480*272 LG lcd, ethernet, gpio/joystick/buttons.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
ESPT-Giga is SH7763-based reference board.
Board support is relatively sparse, presently supporting serial,
gigabit ethernet, USB host, and MTD.
More information (in Japanese) available at:
http://www.cente.jp/product/cente_hard/ESPT-Giga.html
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The KSEG1ADDR macro used to be necessary for the RTL8139 Ethernet
driver, but the code that used that macro was removed over a year
ago, so board configuration files no longer need to define it.
The _IO_BASE macro is also automatically defined to 0 if it isn't
already set, so there's no need to define that macro either in the
board configuration files.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Acked-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Add support for the Phytec phyCORE-MPC5200B-tiny.
Code originally from Pengutronix.de.
Created CONFIG_SYS_ATA_CS_ON_TIMER01 define for when IDE CS is on
Timer 0/1
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
The cm-bf561 module can easily hook up to the EXT-BF5xx-USB-ETH2 extender
board, so add a simple example of how to do that in the board config.
Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The latest blackstamp boards can only run the SPI flash at 15MHz before
they start to crap out, so lower the max speeds accordingly. The new SPI
flash also has different sector requirements, so update the environment
sizes as well.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch fixes 2 problems with FDT EBC mappings on Canyonlands.
First, NAND EBC mapping was missing, making Linux NAND driver
unusable on this board. Second, NOR remapping code assumed that
NOR is always on CS0, however when booting from NAND NOR is on CS3.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Currently, when booting from NAND using nand_spl, in the beginning the default
environment is used until later in boot process the dynamic environment is read
out. This way environment variables that must be interpreted early, like the
baudrate or "silent", cannot be modified dynamically and remain at their
default values. Fix this problem by reading out main and redundand (if used)
copies of the environment in the nand_spl code.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The BF537-STAMP Blackfin board had a driver for working with NAND devices
that are simply memory mapped. Since there is nothing Blackfin specific
about this, generalize the driver a bit so that everyone can leverage it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This sets CONFIG_SYS_HZ to 1000 as required, and completely rewrites
timer code, which is now both correct and much smaller. Unused
functions like udelay_masked() have been removed as no driver uses
them, even the ones that are not currently active for this board.
mtu.h is copied literally from the kernel sources.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The evaluation kit has both Nand and OneNand, both drivers are there
and the two configurations only select a different default for the
jffs partition. This adds the OneNand driver and cleans up storage.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
There is only one public release of the Nomadik chip, so the ifdef
in reset code as well as a define in the config file are not needed
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
This is an error in my side in the initial submission: nobody
calls it ""nmdk8815", it's "nomadik hardware kit", nhk8815, instead.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
This patch adds support for esd gmbh MEESC board.
The MEESC is based on an Atmel AT91SAM9263 SoC.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
Add support for Freescale's i.MX31 PDK board (a.k.a. 3 stack board).
This patch assumes that some other program performs the actual
NAND boot.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Acked-by: Fabio Estevam <fabioestevam@yahoo.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Initial support for Extreme Engineering Solutions XPedite5170 -
a MPC8640-based 3U VPX single board computer with a PMC/XMC
site.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
DMA support is now enabled via the CONFIG_FSL_DMA define instead of the
previous CONFIG_DDR_ECC
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We want the outbound PCI memory map to end at the 4G boundary so we
can maximize the amount of space available for inbound mappings if
we have large amounts of memory.
This matches the device tree setup in the kernel for the 36-bit physical
configs for the platforms that have one (MPC8641 HPCN & MPC8572 DS).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
UART hardware on i.MX27 is the same as on the i.MX31 so we just
need to provide the driver with correct address of the registers.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
this will allow you to store use it for the env and to boot directly U-Boot from
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The PM9261 board is based on the AT91SAM9261-EK board.
Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9261.html
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
move PSRAM init to pm9263.c
this will allow us after to make the nor lowlevel_init generic
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The SPI flash define is named CONFIG_SF_DEFAULT_SPEED, not
CONFIG_SF_DEFAULT_HZ, so fix the typos in the Blackfin boards.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The latest version of U-Boot got a bit fatter in the BSS section which
caused overflows in the RAM region, so increase the monitor size.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The SPI flash layer is much stricter about sector usage than the eeprom
layer we used to use, so update the env settings to better match the
sector alignment of the flashes we use.
Signed-off-by: Vivi Li <vivi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
All drivers need to be converted to CONFIG_NET_MULTI.
This patch converts the dm9000 driver.
Signed-off-by: Thomas Smits <ts.smits@gmail.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Added CONFIG_NET_MULTI to all Davinci boards
Removed all calls to Davinci network driver from board code
Added cpu_eth_init() to cpu/arm926ejs/cpu.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
All the Blackfin linker scripts were duplicated across the board dirs with
no difference save from the semi-often used ENV_IS_EMBEDDED option. So
unify all of them in the lib_blackfin/ dir and for the few boards that
need to embedded the environment directly, add a LDS_BOARD_TEXT define for
them to customize via their board config file. This is much simpler than
forcing them to duplicate the rest of the linker script.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The BF51xF parts have an internal SST SPI flash, so make sure the driver is
enabled by default so we can access it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Blackfin port was using asm/blackfin-config-{pre,post}.h to setup
common Blackfin board defines. The common method now is to use config.h,
so convert blackfin-config-post.h to that. Rename the still Blackfin
specific blackfin-config-pre.h to config-pre.h so the naming conventions
at least line up.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Allow boards to easily override the root= and default bootcmd, allow
people to tweak the file used in default bootcmds at runtime via one env
var, and add a stock nandboot command.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Newer Blackfin parts can an on-chip ROM that can boot LDRs over SPI flashes,
so add a new 'spibootldr' command to take advantage of it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
On MPC8569MDS board, UCC6 and UCC8 can be configured to work at SGMII mode via
UEM on PB board. Since MPC8569 supports up to 4 Gigabit Ethernet ports, we
disable UEC6 and UEC8 by default.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch supports UCC working at RMII mode on PIB board, fixup fdt blob to
support rmii in kernel. It also changes the name of enable_mpc8569mds_qe_mdio to
enalbe_mpc8569mds_qe_uec which is more accurate.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The patch adds support for P2020DS reference platform.
DDR3 interface uses hard-coded initialization rather than SPD
for now and was tested at 667Mhz. Some PIXIS register
definitions and associated code sections need to be fixed.
TSEC1/2/3, NOR flash, MAC/SYS ID EEPROM, PCIE1/2/3 are all
tested under u-boot.
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Travis Wheatley <Travis.Wheatley@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds NAND support to the MPC5121ADS board. Please
note that the image size increased since NAND support didn't
fit in the current image size (256k).
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
The CPCI750 can be built as CPCI host or adapter/target board. This patch
adds support for runtime detection of those variants.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
This patch adds CONFIGs for enabling USB in mpc8536ds and also
adds usb_phy_type in CONFIG_EXTRA_ENV_SETTINGS. Also revamps its
Copyright.
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
This patch adds CONFIGs for enabling USB in mpc8315erdb and also
adds usb_phy_type in CONFIG_EXTRA_ENV_SETTINGS. Also revamps its
Copyright.
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Use the standard lowercase "x" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Use the standard lowercase "xx" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Move needed definitions (register descriptions etc.) from
include/mpc512x.h into include/asm-ppc/immap_512x.h.
Instead of using a #define'd register offset, use a function that
provides the PATA controller's base address.
All the rest of include/mpc512x.h are register offset definitions
which can be eliminated by proper use of C structures.
There are only a few register offsets remaining that are needed in
cpu/mpc512x/start.S; for these we provide cpu/mpc512x/asm-offsets.h
which is intended as a temporary workaround only. In a later patch
this file will be removed, too, and then auto-generated from the
respective C structs.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
We rename the board so we use a consistent name in U-Boot and in
Linux. Also, we use this opportunity to move the board into the
Freecale vendor directory.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
The kernel stores address<->symbol names in it so things can be decoded at
runtime. Do it in U-Boot, and we get nice symbol decoding when crashing.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
By changing the cmd_mtdparts to only use the MTD infrastructure and
not the direct interface to the CFI NOR FLASH driver we now need
to add the MTD infrastructure to all boards using those mtdparts
commands. This patch adds those components:
CONFIG_MTD_DEVICE (for all FLASH types)
plus
CONFIG_FLASH_CFI_MTD (for NOR FLASH)
To all board maintainers: Please test this on your platforms and
report any problems/issues found. Thanks.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Ron Madrid <info@sheldoninst.com>
Cc: Georg Schardt <schardt@team-ctech.de>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Martin Krause <martin.krause@tqs.de>
Cc: Gary Jennejohn <garyj@denx.de>
Cc: Ricardo Ribalda <ricardo.ribalda@uam.es>
Enable the function and interface clocks for banks 2,3,5 and 6.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
With other OMAP3 boards we recently switched to CPU and Board
info API. From parallel merge, this is missing for Zoom2.
Enable it for Zoom2, too.
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Acked-by: Tom Rix <Tom.Rix@windriver.com>
Zoom2 serial is in general supplied by one of the 4 UARTS on the debug board.
The default serial is from the USB connector on left side of the debug board.
The USB connector will produce 2 of the 4 UARTS. On your host pick the first
enumeration.
The details of the setting of the serial gpmc setup are not available.
The values were provided by another party.
The serial port set up is the same with Zoom1.
Baud rate 115200, 8 bit data, no parity, 1 stop bit, no flow.
The kernel bootargs are
console=ttyS3,115200n8
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Also enable display of 'E'mpty sectors in "flinfo" output.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Also reserve more space for U-Boot as it will probably grow soon.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Initial U-Boot support for the DaVinci DM355 EVM. This is a board
from Spectrum Digital. Board docs include schematic and firmware
for its microcontroller:
http://c6000.spectrumdigital.com/evmdm355/revd/
Most of the DM355 chip is fully documented by TI, the most notable
exception being the MPEG/JPEG coprocessor (programmable using codecs
available at no cost from TI), which is omitted from its DM335 sibling:
http://focus.ti.com/docs/prod/folders/print/tms320dm355.html
This version can boot from the on-board DM9000 Ethernet chip, after
being loaded (from NAND, MMC/SD, or UART). In the near future, NAND
and USB support could be added ... NAND support is being held back
until the support for the 4-bit ECC hardware is ready.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The current configuration doesn't define default
bootfile; leading to this warning at execution:
OMAP3_EVM # dhcp
...
...
DHCP client bound to address 192.168.1.11
*** Warning: no boot file name; using 'AC18BE16.img'
TFTP from server 0.0.0.0; our IP address is 192.168.1.11;
sending through gateway 192.168.1.1
Filename 'AC18BE16.img'.
Load address: 0x82000000
Loading: *
TFTP error: 'File not found' (1)
Signed-off-by: Sanjeev Premi <premi@ti.com>
This updates the optional (non-default!) NAND support for the
DaVinci DM6446 EVM:
- include MTD partitioning, defaulting to what Linux uses
- use a flash-based BBT, which among other things speeds bootup
This matches code that's now queued for mainline Linux, and might
even merge in an upcoming 2.6.30-rc; and the MTIDS are set up so
that the U-Boot $mtdparts environment variable can be passed as-is
on the kernel command line as a cmdlinepart override.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Move the clock-rate dumping code into the cpu/.../davinci area
where it should have been, enabled by CONFIG_DISPLAY_CPUINFO,
updating the format and showing the DSP clock (where relevant).
Switch boards to use the cpuinfo() hook for this stuff.
Remove a few now-obsolete PLL #defines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
actually the timer init use the interrupt_init as init callback
which make the interrupt and timer implementation difficult to follow
so now rename it as int timer_init(void) and use interrupt_init for interrupt
btw also remane the corresponding file to the functionnality implemented
as ixp arch implement two timer - one based on interrupt - so all the timer
related code is moved to timer.c
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Split out DaVinci DM6446-specific bits from more generic bits:
- Add a CONFIG_SOC_DM644X. All current boards use DM6446 chips;
DM6443 and DM6441 chips differ in available peripherals.
- Move most DM644X-specific bits from psc.c to a new dm644x.c file,
which is conditionally built. It provides device-specific setup.
Plus minor coding style and comment updates with respect to the PSC.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This patch adds another build target for the AMCC Sequoia PPC440EPx
eval board. This RAM-booting version is targeted for boards without
NOR FLASH (NAND booting) which need a possibility to initially
program their NAND FLASH. Using a JTAG debugger (e.g. BDI2000/3000)
configured to setup the SDRAM, this debugger can load this RAM-
booting image to the target address in SDRAM (in this case 0x1000000)
and start it there. Then U-Boot's standard NAND commands can be
used to program the NAND FLASH (e.g. "nand write ...").
Here the commands to load and start this image from the BDI2000:
440EPX>reset halt
440EPX>load 0x1000000 /tftpboot/sequoia/u-boot.bin
440EPX>go 0x1000000
Please note that this image automatically scans for an already
initialized SDRAM TLB (detected by EPN=0). This TLB will not be
cleared. This TLB doesn't need to be TLB #0, this RAM-booting
version will detect it and preserve it. So booting via BDI2000
will work and booting with a complete different TLB init via
U-Boot works as well.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes the cpld binary bitstream that is
used by esd's cpld command on DP405 boards.
Because u-boot with an external cpld bitstream may not
take more space in flash than before the u-boot binary is
shrinked a little bit. Some unused featues have been
removed therefore.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes the cpld binary bitstream that is
used by esd's cpld command on VOM405 boards.
Because u-boot with an external cpld bitstream may not
take more space in flash than before the u-boot binary is
shrinked a little bit.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes the cpld binary bitstream that is
used by esd's cpld command on PMC405 boards.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes the cpld binary bitstream that is
used by esd's cpld command on CMS700 boards.
Because u-boot with an external cpld bitstream may not
take more space in flash than before the u-boot binary is
shrinked a little bit. Some unused featues have been
removed therefore.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
The individual i2c commands imd, imm, inm, imw, icrc32, iprobe, iloop,
and isdram are no longer available so all references to them have been
updated to the new form of "i2c <cmd>".
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
The following individual I2C commands have been removed: imd, imm, inm,
imw, icrc32, iprobe, iloop, isdram.
The functionality of the individual commands is still available via
the 'i2c' command.
This change only has an impact on those boards which did not have
CONFIG_I2C_CMD_TREE defined.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Add standard CONFIG_SYS_I2C_SPEED define for the mpc7448hpc2 so that
it can use the common 'i2c speed' command. Note that the I2C controller
utilized by the mpc7448hpc2 has a fixed speed and cannot be changed
dynamically.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Yu Liu <Yu.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Increase the size of malloc to 512KB because MPC8569MDS needs more memory for
malloc to support up to eight Ethernet interfaces.
- Move Environment address out of uboot thus the saved environment variables
will not be erased after u-boot is re-programmed.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove "saveenv" from "update" definition: the environment is outside
the U-Boot image on TQM85xx and therefor not affected by updates.
Also "beautify" code a bit (vertical alignment).
Signed-off-by: Wolfgang Denk <wd@denx.de>
Old TQM85xx boards had 'M' type Spansion Flashes from the S29GLxxxM
series while new boards have 'N' type Flashes from the S29GLxxxN
series, which have bigger sectors: 2 x 128 instead of 2 x 64 KB.
We now change the configuration to the new flash types for all
boards; this also works on old boards - we just waste two flash
sectors for the environment which could be smaller there.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The SYS_CLK_IN of MPC8569MDS is 66.66MHz,
The DDR_CLK_IN is same with SYS_CLK_IN in 8569 processor.
so, change the SYS_CLK_IN from 66MHz to 66.66MHz.
Signed-off-by: Dave Liu <daveliu@freescale.com>
