Conver TI CPSW driver to use dev/ofnode api.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
[trini: Add <dm/ofnode.h> to provide the prototype to ofnode]
Signed-off-by: Tom Rini <trini@konsulko.com>
- Add support for Intel FSP-S and FSP-T in binman
- Correct priority selection for image loaders for SPL
- Add a size check for TPL
- Various small SPL/TPL bug fixes and changes
- SPI: Add support for memory-mapped flash
On i.MX7 in a sake of reducing the disturbances caused by a neighboring
cells in the FCB page in the NAND chip, a randomizer is enabled when
reading the FCB page by ROM bootloader.
Add API for setting BCH to specific layout (and restoring it back) used by
ROM bootloader to be able to burn it in a proper way to NAND using
nandbcb command.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Need to pass total 5 arguments for SIP HAB call on i.MX8MQ,
so update the interface to add new argument.
Signed-off-by: Ye Li <ye.li@nxp.com>
[agust: fixed imx8m-power-domain build]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Set gd->fb_base so it can be shown with bdinfo command.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The expire_now function was previously setting the watchdog timeout to
minimum and waiting for the watchdog to expire. However, this watchdog
also has bits to trigger immediate reset. Use those instead, like the
Linux imx2_wdt driver does.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
The Linux imx2_wdt driver uses a fsl,ext-reset-output boolean in the
device tree to specify whether the board design should use the external
reset instead of the internal reset. Use this boolean to determine which
mode to use rather than using external reset unconditionally.
For the legacy non-DM mode, the external reset is always used in order
to maintain the previous behavior.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Now AM65x CPSW2G driver will disable MAC TX internal delay for PHY
interface mode "rgmii-rxid" which is incorrect. Hence, fix it by keeping
default value (enabled) for MAC TX internal delay when "rgmii-rxid"
interface mode is selected.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Now TI CPSW driver will disable MAC TX internal delay for PHY interface
mode "rgmii-rxid" which is incorrect.
Hence, fix it by keeping default value (enabled) for MAC TX internal delay
when "rgmii-rxid" interface mode is selected.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
This patch adds support for standard Ethernet "max-speed" DT property to
allow PHY link speed limitation.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
According to TRMs the 10Mbps link speed is supported in RGMII only when
CPSW2G MAC SL is configured for External Control ("in band") mode
CPSW_SL_MACCTRL.EXT_EN(18) = 1.
Hence update cpsw_slave_update_link() to follow documentation.
[1] https://patchwork.kernel.org/patch/10285239/
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
At present the value of the timer base is used to determine whether the
timer has been set up or not. It is true that the timer is essentially
never exactly 0 when it is read. However 'time 0' may indicate the time
that the machine was reset so it is useful to be able to denote that.
Update the code to use a separate flag instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function can be called before the timer is set up. Make sure that the
init function is called so that it works correctly.
This is needed so that bootstage can work correctly in TPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
On x86 platforms the SPI flash can be mapped into memory so that the
contents can be read with normal memory accesses.
Add a new SPI method to find the location of the SPI flash in memory. This
differs from the existing device-tree "memory-map" mechanism in that the
location can be discovered at run-time.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
ARC fixes for v2020.01-rc2
The main change is move to DM_MMC of yet 2 another ARC boards:
AXS101 & IoTDK.
Among that we improve handling of stock-formatted SD-cards of high volume
on EM SDP as well as introduction of reset driver for HSDK which is required
for prepser reinitialization of some peripherals like USB etc.
Provide a better user interface for setting UEFI variables.
Bug fixes:
- ext4 file system not discovered on UEFI block device
- 'make tests' build error on 32bit systems
-----BEGIN PGP SIGNATURE-----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=f0m8
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-01-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-01-rc2
Provide a better user interface for setting UEFI variables.
Bug fixes:
- ext4 file system not discovered on UEFI block device
- 'make tests' build error on 32bit systems
Bootstage improvements for TPL, SPL
Various sandbox and dm improvements and fixes
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl24zDoRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZRiwf+Mf7oG//zjiZcHaPP6KOFb1CjwqLSuiaI
eCYB6GEZXuSpc8MjAw+baAfIw8MMFuaCfPsUQ5dDo391neK0sW9kkEsdcXnQBpB3
GdJYcewLN1UuJZovriGobIisGc0GQHh8gmRcVGWSKoEt+gAQauRtVYBIUPuS3JG+
ihZgYmVgICa+3tqavIbP2oZdXLuLAxR65mfiQHtiJwdCN3OOzyls2v0T0slQX9GV
ln6EvTk8OMIudBmkB7YiTmJF7AB+3PH/uBaiYyTKO9gtjLhnmCFvG5HxJTRFOKvU
F4oVWZJDEcqfZvYgWg8i5vgokMP41nzLfBr7j5ifUX1f3xwCHy/Tpw==
=S4XI
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-29oct19' of git://git.denx.de/u-boot-dm
- Fix for patman with email addresses containing commas
- Bootstage improvements for TPL, SPL
- Various sandbox and dm improvements and fixes
For some controllers PHYs can be optional. Handling NULL pointers without
crashing nor failing, makes it easy to handle optional PHYs.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Change the stack-allocated buffer for the identification command
to explicitly allocate page-aligned buffers. Even though the spec
seems to allow having admin queue commands on non page-aligned
buffers, it seems to not be possible on my i.MX8MQ board with a
a Silicon Power P34A80. Since all of the NVMe drivers I have seen
always do admin commands on a page-aligned buffer, which does work
on my system, it makes sense for us to do that as well.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It's possible that the data cache for the buffer still holds data
to be flushed to memory, since the buffer was probably used as stack
before. Thus we need to make sure to flush it also on reads, since
it's possible that the cache is automatically flused to memory after
the NVMe DMA transfer happened, thus overwriting the NVMe transfer's
data. Also add a missing dcache flush for the prp list.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Profiling the EHCI driver shows a significant performance problem in
ehci_submit_async(). Specifically, this function keeps enabling and
disabling async schedule back and forth for every single transaction.
However, enabling/disabling the async schedule does not take effect
immediatelly, but instead may take up to 1 mS (8 uFrames) to complete.
This impacts USB storage significantly, esp. since the recent reduction
of maximum transfer size to support more USB storage devices. This in
turn results in sharp increase in the number of ehci_submit_async()
calls. Since one USB storage BBB transfer does three such calls and
the maximum transfer size is 120 kiB, the overhead is 6 mS per 120 kiB,
which is unacceptable.
However, this overhead can be removed simply by keeping the async
schedule running. Specifically, the first transfer starts the async
schedule and then each and every subsequent transfer only adds a new
QH into that schedule, waits until the QH is completed and does NOT
disable the async schedule. The async schedule is stopped only by
shutting down the controller, which must happen before moving out
of U-Boot, otherwise the controller will corrupt memory.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Add weak callback to allow board specific behavior
- flush
- initiated
This patch prepare usage of DFU back end for communication with
STM32CubeProgrammer on stm32mp1 platform with stm32prog command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add a virtual DFU backend to allow board specific read and write
(for OTP update for example).
Acked-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add the support of MTD partition for the MTD backend.
The expected dfu_alt_info for one alternate on the mtd device :
<name> part <part_id>
<name> partubi <part_id>
"partubi" also erase up to the end of the partition after write operation.
For example: dfu_alt_info = "spl part 1;u-boot part 2; UBI partubi 3"
U-Boot> dfu 0 mtd nand0
Acked-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add DFU backend for MTD device: allow to read
and write on all MTD device (NAND, SPI-NOR,
SPI-NAND,...)
For example :
> set dfu_alt_info "nand_raw raw 0x0 0x100000"
> dfu 0 mtd nand0
This MTD backend provides the same level than dfu nand
backend for NAND and dfu sf backend for SPI-NOR;
So it can replace booth of them but it also
add support of spi-nand.
> set dfu_alt_info "nand_raw raw 0x0 0x100000"
> dfu 0 mtd spi-nand0
The backend code is based on the "mtd" command
introduced by commit 5db66b3aee ("cmd: mtd:
add 'mtd' command")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch allows the DFU backend to indicate that that it can't
provide no more data to fill the DFU buffer, by setting b_left =0
without error, even if the size of received data is lower of the
expected total size indicated by get_medium_size.
For USB DFU stack point of view, it is acceptable:
the read length < requested size in DFU_UPLOAD and the
transaction is stopped.
That avoid infinite loop issue in dfu_read_buffer_fill because the
size for the DFU read is limited by get_medium_size = r_left
and the DFU stack expects that read is allowed up to this size.
This issue never occurs for current flash device (where chunk are
always completely read, and b_left will be never 0) but it is useful for
virtual partition when the backend only know the max size of this
alternate, the real size of the data are only known in the read
treatment.
PS: for file access on mmc, EOF is never reached as
dfu_get_medium_size_mmc returns the exact size of the file.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support of DFU for several interface/device
with one command.
The format for "dfu_alt_info" in this case is :
- <interface> <dev>'='alternate list (';' separated)
- each interface is separated by '&'
The previous behavior is always supported.
One example for NOR (bootloaders) + NAND (rootfs in UBI):
U-Boot> env set dfu_alt_info \
"sf 0:0:10000000:0=spl part 0 1;u-boot part 0 2; \
u-boot-env part 0 3&nand 0=UBI partubi 0,3"
U-Boot> dfu 0 list
DFU alt settings list:
dev: SF alt: 0 name: spl layout: RAW_ADDR
dev: SF alt: 1 name: ssbl layout: RAW_ADDR
dev: SF alt: 2 name: u-boot-env layout: RAW_ADDR
dev: NAND alt: 3 name: UBI layout: RAW_ADDR
U-Boot> dfu 0
$> dfu-util -l
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=3, name="UBI", serial="002700333338511934383330"
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=2, name="u-boot-env", serial="002700333338511934383330"
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=1, name="u-boot", serial="002700333338511934383330"
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=0, name="spl", serial="002700333338511934383330"
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Copy the partition support from NAND backend to SF,
support part and partubi option.
In case of ubi partition, erase the rest of the
partition as it is mandatory for UBI.
The added code is under compilation flag CONFIG_DFU_SF_PART
activated by default.
for example:
U-Boot> env set dfu_alt_info "spl part 0 1;\
u-boot part 0 2;u-boot-env part 0 3;UBI partubi 0 4"
U-Boot> dfu 0 sf 0:0:10000000:0
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Calling cache flush on invalid buffer, even with zero length might cause
an exception on certain platforms.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Add possibility to define a part of partition as a separate DFU entity.
This allows to have more than one items on the given partition.
The real use case for this option is TM2 board. It can use u-boot stored
as Linux kernel on the defined partition (as RAW data) and load the real
kernel from the same partition, but stored under the certain offset.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
This is needed to make Windows THOR flash tool happy, because it
starts sending data only when interrupt packet is received on the 3rd
endpoint.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
In combination with multiple partitions in NAND, this printf() ends up
being more noise than helpful. Change it to debug() instead.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Acked-by: Lukasz Majewski <lukma@denx.de>
Some boards don't populate clk/reset entries as these are are optional
as per binding documentation. Therefore, don't fail driver probe if
clk/reset entries are absent in DT.
This fixes fastboot failures seen due to enabling of CONFIG_CLK on AM57xx
Fixes: e8e683d33b ("board: ti: am57xx-idk: Configure the CDCE913 clock synthesizer")
Reported-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
_gpio_direction_output function currently calls gpio_set_value
with the wrong gpio number. gpio_set_value in the uclass driver
expects a different gpio number and the _gpio_direction_output
is currently providing the number specific to the bank.
Hence fix it by calling the _gpio_set_value function instead.
Reported-by: Faiz Abbas <faiz_abbas@ti.com>
Fixes: 8e51c0f254 ("dm: gpio: Add DM compatibility to GPIO driver for Davinci")
Signed-off-by: Keerthy <j-keerthy@ti.com>
- Add I2C clocks for i.MX6Q CCF driver
- Fix check in clk_set_default_parents()
- Managed API to get clock from device tree
- Fixes for core clock code (including sandbox regression tests)
The ext4 file system requires log2blksz to be set. So when setting the
block size on the block descriptor we should fill this field too.
This fixes a problem with EFI block devices providing ext4 partitions, cf.
https://lists.denx.de/pipermail/u-boot/2019-October/387702.html.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
A previous patch below adding DDR mode support was actually for i.MX
platforms. Now i.MX eSDHC driver is fsl_esdhc_imx.c. For QorIQ eSDHC,
it uses different process for DDR mode, and hasn't been supported.
Let's drop DDR support code for i.MX in fsl_esdhc driver.
0e1bf61 mmc: fsl_esdhc: Add support for DDR mode
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
U-boot prefers DM_MMC + BLK for MMC. Now eSDHC driver has already
support it, so let's force to use it.
- Drop non-BLK support for DM_MMC introduced by below patch.
66fa035 mmc: fsl_esdhc: fix probe issue without CONFIG_BLK enabled
- Support only DM_MMC + BLK (assuming BLK is always enabled for DM_MMC).
- Use DM_MMC instead of BLK for conditional compile.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Use log() insted of debug() for uclass_find_device_by_seq function,
since this print is very much and we can filter it out with log()
interface.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move #define to top of file as per docs:
Signed-off-by: Simon Glass <sjg@chromium.org>
This function assumes that the 'val' parameter has no masked bits set.
This is not defined by the function prototype though. Fix the function to
mask the value and update the documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
- bmips: various small fixes
- mtmips: add new drivers for clock, reset-controller and pinctrl
- mtmips: add support for high speed UART
- mtmips: update/enhance drivers for SPI and ethernet
- mtmips: add support for MMC
-----BEGIN PGP SIGNATURE-----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=6G/J
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2019-10-25' of git://git.denx.de/u-boot-mips
- bmips: add BCRM NAND support for BCM6368, BCM6328, BCM6362 and BCM63268 SoCs
- bmips: various small fixes
- mtmips: add new drivers for clock, reset-controller and pinctrl
- mtmips: add support for high speed UART
- mtmips: update/enhance drivers for SPI and ethernet
- mtmips: add support for MMC
The J721E DDR subsystem comprises DDR controller, DDR PHY and wrapper
logic to integrate these blocks in the device. The DDR subsystem is
used to provide an interface to external SDRAM devices which can be
utilized for storing program or data. Introduce support for the
DDR controller and DDR phy within the DDR subsystem.
Signed-off-by: Kevin Scholz <k-scholz@ti.com
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Added the following registers to the DDR configuration:
- ACIOCR0,
- ACIOCR3,
- V2H_CTL_REG,
- DX8SLxDQSCTL.
Modified enable_dqs_pd and disable_dqs_pd to only touch the associated
bit fields for pullup and pulldown registers (to preserve slew rate and
other bits in that same register). Also update the dts files in the same
patch to maintain git bisectability.
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Added training support for LPDDR4 and DDR3L DDRs. Also added/changed
some register configuration to support all 3 DDR types
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdspnqAAoJEB6zHgIOrC/Ixi4IAJEEiCZPu6Z3fbkFX/Um7vCX
eMTltJN8nz4oiSi3xdx3ejueqWdW3F8VuCkHb0j0bVAhMlUlVgwCzfd0cD+D2iwS
jkrgzASNAr+JeYKYEdWqqfaUxOCd2qfuBu9EXlpvKQLWLt+KRfsOsHWcgR4bf095
aGCihvd/fKhKYUvbf5cEQnsWa3UwtsKk4Web5MKjxXx3p0iVNlu4KLd/vDWfTios
X1NqiO5ZjXNrDxyG6Aj8lgDXlE5kfeKaN/aCJU1/0U2cXm8JRu2w2dv1P/e/kU+j
NHIGzICAG4Lk/4gQTeuohJxLyvj7K3i1H12ik9Qeh4H1/5fsyybyltGUo7H443s=
=JYe3
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2020.01-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features and fixes for 2020.01 cycle
This feature set includes Eugen's work on a new tiny flexcom driver and
eeprom mac retrieval for the sam9x60-ek board.
This patch adds a dts property cd-active-high for builtin-cd mode to make
it configurable instead of using hardcoded active-low.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch add support for mt7628-eth to isolate LAN/WAN ports mainly to
prevent LAN devices from getting IP address from WAN.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
When received a packet with an invalid length recorded in rx descriptor,
we should free this rx descriptor to allow us to continue to receive
following packets.
Without doing so, u-boot will stuck in a dead loop trying to process this
invalid rx descriptor.
This patch adds a call to mt7628_eth_free_pkt() after received an invalid
packet length.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The mt7628 has an embedded ethernet switch (5 phy ports + 1 cpu port).
Although in IOT mode only port0 is usable, the phy0 is still connected
to the switch, not the ethernet gmac directly.
This patch rewrites it and makes it optional. It can be turned on by adding
mediatek,poll-link-phy = <?> explicitly into the eth node. By default the
driver is switch mode with all 5 phy ports working without link detection.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch removes hardcoded gpio settings as they have been replaced by
pinctrl in dts, and also replaces regmap-based phy reset with a more
generic reset controller.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds slew rate calibration for mt76x8-usb-phy, removes code
which belongs to mt7620, and gets rid of using syscon and regmap by using
clock driver and reset controller.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds pinctrl support for mt7628, with a file for common pinmux
functions and a file for mt7628 which has additional support for pinconf.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Currently this driver uses a different way to implement the spi xfer,
by modifying some fields of two registers, which is incompatible with the
MTK's original SDK linux driver. This will cause the flash data being
damaged by the SDK driver.
This patch lets the mt7621_spi_set_cs() restore the original register
fields after cs deactivated.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The mt7621 spi controller supports continuous generic half-duplex spi
transaction. There is no need to cache xfer data at all.
To achieve this goal, the OPADDR register must be used as the first data
to be sent. And follows the eight generic DIDO registers. But one thing
different between OPADDR and DIDO registers is OPADDR has a reversed byte
order.
With this patch, any amount of data can be read/written in a single xfer
function call.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch lets the spi driver to use clock provided by the clk driver
since the new clk-mt7628 driver provides accurate sys clock frequency.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds a clock driver for MediaTek MT7628/7688 SoC.
It provides clock gate control as well as getting clock frequency for
CPU/SYS/XTAL and some peripherals.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds non-DM version for mtk hsuart driver and makes it
compatible with ns16550a driver in configuration.
This is needed in SPL with CONFIG_SPL_DM disabled for reducing size.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The current brcmnand driver is based on 4.18 linux kernel which uses
mtd_set_ooblayout to set ecc layout. But nand base code in u-boot is from
old kernel which does not use this new API and expect nand_chip.ecc.layout
structure to be set. This cause nand_scan_tail function running into a bug
check if the device has a different oob size than the default ones.
This patch ports the brcmstb_choose_ecc_layout function from kernel 4.6.7
that supports the ecc layout struture and replaces the mtd_set_ooblayout
method
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
This adds support for BCM6368, BCM6328, BCM6362 and BCM63268 SoCs.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add an entry for the Adesto AT25SL321 SPI NOR chip.
This SPI NOR chip is found in the Embedded Artist i.MX7ULP COM board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Most boards currently use SPI_FLASH_MTD only in U-Boot proper, not in
SPL. They often rely on hacks in the board header files to include
this option conditionally. To be able to fix this, we previously
introduced a separate option SPL_SPI_FLASH_MTD.
Therefore we can now adjust the Makefile and change the code in
sf_probe.c and sf_internal.h to use CONFIG_IS_ENABLED(SPI_FLASH_MTD).
We also need to move all occurences of CONFIG_SPI_FLASH_MTD from the
header files to the according defconfigs. The affected boards are
socfpga, aristainetos, cm_fx6, display5, ventana, rcar-gen2, dh_imx6
and da850evm.
We do this all in one patch to guarantee bisectibility.
This change was tested with buildman to make sure it does not
introduce any regressions by comparing the resulting binary sizes.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
n25q* and mt25q* (both 256Mb and 512Mb) flashes support Flag status
register that indicates various errors that may be encountered during
erase/write operations. Therefore add USE_FSR flag wherever missing.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
mt25q* flashes support stateless 4 byte addressing opcodes. Add entries
for the same. These flashes have bit 6 set in 5th byte of READ ID
response when compared to n25q* variants.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Per datasheets of n25q256* and n25q512* not all variants of n25q256* and
n25q512* support 4 Byte stateless addressing opcodes. Therefore drop
SPI_NOR_4B_OPCODES flag from these entries
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Disable and free clock when remove driver.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
U-Boot uses CONFIG_SPI_FLASH_USE_4K_SECTORS to enable 4K small sector
support. Use that instead of MTD_SPI_NOR_USE_4K_SECTORS.
Reported-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Use dev_err() when reporting reason for erase/write failures so that
users can be made aware of the reason for failure.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
To allow SPI_FLASH_MTD being enabled separately in SPL we add a new
option. The only user currently is the stm32mp15_basic board.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
SPI_SUNXI driver is fully dm-aware and the Allwinner
architecture kconfig would have logic to enable the
DM_SPI. So, select default spi sunxi driver for
sunxi architecture.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
DM_SPI_FLASH should require spi flash interface code for dm
version, so imply SPI_FLASH core by default if any board
enabled DM_SPI_FLASH.
This overcome the explicit enablement of CONFIG_SPI_FLASH on
respective boards when DM_SPI_FLASH being used.
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
We need distinguish the following two situations in various SPI APIs:
- given chip select num is invalid
- given chip select num is valid, but no device is attached
Currently -ENODEV is returned for both cases.
For the first case, it's more reasonable to return -EINVAL instead of
-ENODEV for invalid chip select numbers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # SoPine
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
If an SPI controller driver does not implement ops->cs_info, that
probably means any chip select number could be valid, hence let's
return 0 for spi_cs_info().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # SoPine
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add is25wp256, chip to spi-nor id table.
Tested on SiFive FU540 board.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
1) CONFIG_SPI_FLASH is not just a legacy code, but it has common
core code which handle both dm and non-dm spi flash code. So
fix the info text to make it clear globally.
2) Since it's flash core it shouldn't depends on legacy SPI,
so remove the 'depends on SPI'
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The ULP has two USB controllers. These two controllers have similar NC
registers layout as i.MX7D. But OTG0 uses UTMI PHY simliar as i.MX6, not
the integrated PHY on i.MX7D. The OTG1 needs off-chip HSIC PHY or ULPI PHY
to work.
This patch only supports OTG0 with UTMI PHY.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
This fixes the issues with calculation of controller indexes in
ehci_usb_bind() for iMX7, as USB controllers on iMX7 SoCs aren't
placed next to each other, and their addresses incremented by 0x10000.
Example of USB nodes for iMX7S/D:
usbotg1: usb@30b10000 {
compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
reg = <0x30b10000 0x200>;
^^^^^^^^^^
....
usbotg2: usb@30b20000 {
compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
reg = <0x30b20000 0x200>;
^^^^^^^^^^
....
usbh: usb@30b30000 {
compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
reg = <0x30b30000 0x200>;
^^^^^^^^^^
....
Which was leading to usb enumeration issues:
Colibri iMX7 # usb start
starting USB...
Bus usb@30b10000: USB EHCI 1.00
Bus usb@30b20000: probe failed, error -22
scanning bus usb@30b10000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Fixes: 501547cec1("usb: ehci-mx6: Fix bus enumeration for DM case")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This patch adds manual relocation for Modular Exponentiation if
CONFIG_NEEDS_MANUAL_RELOC is enabled.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for gpio driver for pmc gpio.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for gpio driver for versal platform
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Fix error debug messages to be more accurate and aligned with debug message
style in the whole file.
And do not initialize ret variable because it is initialized later on and
it is just additional step.
Fixes: 1327d1678b ("firmware: zynqmp: Add zynqmp-power support")
Reported-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Function should report error when called in EL3 context. Also report it as
error instead 0 (success).
Reported-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Remove macros which use PM_SIP_SVC offset and convert invoke_smc() to
xilinx_pm_request() which do calculation with PM_SIP_SVC already.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
versal_pm_request() and invoke_smc() are almost the same. Only one
difference is that versal_pm_request is adding PM_SIP_SVC offset to api_id.
The patch is moving platform implementation to firmware driver code for
synchronization.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
The Microchip Flexcom is just a wrapper which embeds a SPI controller,
an I2C controller and an USART.
Only one function can be used at a time and is chosen at boot time according
to the device tree.
The bindings are kept as in Linux.
The driver registers to MISC_UCLASS.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
There is no proper power domain support for the keystone platforms.
However we need to turn off the USB domains before jumping to linux or it
fail to boot (observed with k2e and k2l platforms).
This can be done in the PHY driver as it is dedicated only to the keystone
platforms and matches the required on/off sequence.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The mode selection for the DWC3 is kind of obsolete. The driver does not
have to be host only or gadget only. This choice is confusing.
All the remaining callers of dwc3_uboot_init() explicitly set dr_mode
before calling the function, so none rely on a default behavior.
Remove the choice menu and keep only the USB_DWC3_GADGET option. Enable it
by default if USB_GADGET and USB_DWC3 are enabled.
It must be disabled for the evb-rk3328 as it uses DWC2 for the gadget and
DWC3 for the host.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a new function that read quirk and configuration information from the
DT. The goal is to allow platforms using their own version of DWC3 driver
to migrate to the generic DWC3 driver.
The function is adapted from the function dwc3_get_properties() in the
linux dwc3 driver introduced in commit c5ac6116db35d.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
There is no need to fail if the maximum speed is not specified.
If the speed is not specified, do the same as linux and assume super speed.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Currently the host driver used by dwc3-generic is "xhci-dwc3". This is
a functional driver but it doesn't use the dwc3 core and, in particular,
it lacks some bits that may be important.
For example on the k2 platforms, it is important that the phy are properly
suspended when the USB is not used anymore. The dwc3 core also has a
partial support for quirks.
The new driver can be used as a drop-in replacement for "xhci-dwc3".
In terms of implementation, it may seem strange that 2 private structures
dwc3_generic_host_priv and dwc3_generic_priv) are used. The reason for this
is simply that the xhci layer expects a struct xhci_ctrl at the beginning
of the private data and it seemed wasteful to include it also for the
peripheral case.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
No one is actually implementing those functions.
We could remove calls to these altogether, but it does not really hurt to
keep the empty inlined version at the moment and it satisfies a symmetry
with the gadget mode.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The xhci.h header file is currently located under drivers/usb/xhci
Move it to the include/usb folder to make it available to drivers that
are not under drivers/usb/xhci
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This allow the phy to enter idle and then suspend.
the K2 platforms require the PHY to be suspended before the USB domain
clock can be turned off.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
AM654/J721e has HyperBus Memory Controller that supports HyperFlash and
HyperRAM devices. It provides a memory mapped interface to interact with
these devices. Add a driver to support the same.
Driver calibrates the controller, setups up for MMIO access and probes
HyperFlash child node.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Make use of CONFIG_SYS_MONITOR_BASE only when available to avoid build
error when CONFIG_SYS_MONITOR_BASE is not defined.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add Support for UFS Host Controller Interface (UFSHCI) for communicating
with Universal Flash Storage (UFS) devices. The steps to initialize the
host controller interface are the following:
- Initiate the Host Controller Initialization process by writing to the
Host controller enable register.
- Configure the Host Controller base address registers by allocating a
host memory space and related data structures.
- Unipro link startup procedure
- Check for connected device
- Configure UFS host controller to process requests
Also register this host controller as a SCSI host controller.
Taken from Linux Kernel v5.2 (drivers/scsi/ufs/ufshcd.c) and ported to
U-boot.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Some SCSI devices like UFS use DMA for executing scsi commands and hence
need to know the direction of transfer of the dma. Add a dma_dir element
to the command structure to facilitate this.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
The UFS SCSI device LUNs are observed to return failure the first time a
unit ready inquiry is sent and pass on the second try. Send this
inquiry 3 times to make sure device is ready.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Add max_bytes_per_req to scsi_platdata to enable the host driver to limit
the number of bytes that can be read/written per request.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
With no non-DM driver using scsi_read()/_write() APIs, remove
the legacy implementations.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
[trini: Reorder slightly and mark scsi_read/write behind BLK test to
avoid warnings]
Signed-off-by: Tom Rini <trini@konsulko.com>
Make sure that the clock self-assignment works by having a clock of
clk-sbox be configured automatically when clk-sbox is probed.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This fixes the case where assigned-clocks is used to define a clock
defaults inside this same clock's node. This is used sometimes to setup a
default parents and/or rate for a clock.
example:
muxed_clock: muxed_clock {
clocks = <&clk_provider 0>, <&clk_provider 1>;
#clock-cells = <0>;
assigned-clocks = <&muxed_clock>;
assigned-clock-parents = <&clk_provider 1>;
};
It doesn't work in u-boot because the assigned-clocks are setup *before*
the clock is probed. (clk_set_parent() will likely crash or fail if called
before the device probe function)
Making it work by handling "assigned-clocks" in 2 steps: first before the
clk device is probed, and then after the clk device is probed.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a few more clocks the clk_sandbox clock provider and get them using
the managed API.
Make sure they are released when the device is removed.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add devm_clk_get(), devm_clk_get_optional() to get clocks from the
device-tree. The clocks is automatically released and the data structure
freed when the device is unbound.
Also add devm_clk_put() to release the clock and free the data structure
manually.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This change adds support for I2C clock modeled in CCF. This code intention
is to only enable those clocks in the I2C driver with default settings.
For that reason the "busy" versions of clocks reuse the generic approach
and would need to be updated when one wants to adjust the I2C clock
frequency in U-Boot.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
According to the documentation in clk.h, clk_set_parent() return the new
rate of the clock or a negative error code.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Correct the name of the define used CONFIG_IS_ENABLED which is
not aligned with Kconfig name: CONFIG_$(SPL_)PINCONF_RECURSIVE.
The recursive calls is conditional only for UCLASS_PINCONFIG
"pinconfig" driver.
It is always needed to call pinctrl_post_bind for UCLASS_PINCTRL
"pinctrl", the test CONFIG_IS_ENABLED(PINCONF_RECURSIVE) need to
be removed for this driver.
This correct a regression introduced because the same patch is
applied twice times in u-boot-dm branch:
- commit e878b53a79 ("dm: pinctrl: introduce PINCONF_RECURSIVE
option")
- commit c20851b3d8 ("dm: pinctrl: introduce PINCONF_RECURSIVE
option")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
- add HDMI/CVBS display support for Amlogic G12A SoCs and SEI510 board
- add support for Amlogic A311D based Khadas VIM3
- add support for Amlogic S905X3 based SEI610 board, targeting Android support like SEI510
-----BEGIN PGP SIGNATURE-----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=g/kq
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20191018' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- document alternative libretech-cc installation methods, including upstream TF-A and opensource tools
- add HDMI/CVBS display support for Amlogic G12A SoCs and SEI510 board
- add support for Amlogic A311D based Khadas VIM3
- add support for Amlogic S905X3 based SEI610 board, targeting Android support like SEI510
Based on the 54ecb8f7028c ("Linux 5.4-rc1") Everything-Else power domain
driver for Amlogic SoCs.
This driver handles the VPU Power domain and other domains from the
Everything-Else part of the SM1 and G12A SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The SM1 clock controller is almost identical to the G12A and
so far the differences don't matter.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Finally add the Amlogic G12A SoC compatible for the VPU driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Synchronize the Amlogic Meson Video driver back with the latest
DRM misc tree, adding G12A platform support, from the latest commit:
528a25d040bc ("drm: meson: use match data to detect vpu compatibility")
The sync includes the following changes from Linux adapted to U-Boot:
- Add support for VIC alternate timings
- Switch PLL to 5.94GHz base for 297Mhz pixel clock
- Add registers for G12A SoC
- Add G12A Support for VPP setup
- Add G12A Support for VIU setup
- Add G12A support for OSD1 Plane
- Add G12A support for plane handling in CRTC driver
- Add G12A support for CVBS Encoder
- Add G12A Video Clock setup
- Add G12A support for the DW-HDMI Glue
- fix G12A HDMI PLL settings for 4K60 1000/1001 variations
- fix primary plane disabling
- fix G12A primary plane disabling
- mask value when writing bits relaxed
- crtc: drv: vpp: viu: venc: use proper macros instead of magic constants
- global clean-up
- add macro used to enable HDMI PLL
- venc: set the correct macrovision max amplitude value
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Remove getting and enabling the node power domain since it's now handled
by the dm core directly.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Add necessary clock support to set up clock for the VPU and
HDMI support.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Add Amlogic G12A support for the gx-pwrc driver, aligned on the
Linux v5.2 driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This patch adds a DM based driver model for gpio controller present in
FU540-C000 SoC on HiFive Unleashed A00 board. This SoC has one GPIO
bank and 16 GPIO lines in total, out of which GPIO0 to GPIO9 and
GPIO15 are routed to the J1 header on the board.
This implementation is ported from linux based gpio driver submitted
for review by Wesley W. Terpstra <wesley@sifive.com> and/or Atish Patra
<atish.patra@wdc.com> (many thanks !!). The linux driver can be referred
here [1]
[1]: https://lkml.org/lkml/2018/10/9/1103
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
ubi enhancements for 2020.01
- provide a way for skipping crc checks ported from linux, and add an
U-Boot command to set this flag on already installed systems.
- fix redundand environment management
It might be interesting, if "skip_check" is set or not, so lets print
this flag in ubi_dump_vol_info() as well.
hs: fix typo in commit message
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Quentin Schulz <quentin.schulz@bootlin.com>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Some users of static UBI volumes implement their own integrity check,
thus making the volume CRC check done at open time useless. For
instance, this is the case when one use the ubiblock + dm-verity +
squashfs combination, where dm-verity already checks integrity of the
block device but this time at the block granularity instead of verifying
the whole volume.
Skipping this test drastically improves the boot-time.
Adapted to U-Boot by Stefan Roese.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Quentin Schulz <quentin.schulz@bootlin.com>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
At present the 'Index' column of 'dm tree' assumes there is
two digits, this patch increase it to 3 digits.
It also aligns output of 'dm uclass', assuming the same 3 digits index.
The boards with CONFIG_PINCTRL_FULL activated have one pinconfig
by pin configuration, so they can have more than 100 devices
pinconfig (for example with stm32mp157c-ev1 board we have
106 pinconfig node).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the Linux pinctrl binding, the pin configuration nodes don't need to
be direct children of the pin controller device (may be grandchildren for
example). This behavior is managed with the pinconfig u-class which
recursively bind all the sub-node of the pin controller.
But for some binding (when pin configuration is only children of pin
controller) that is not necessary. U-Boot can save memory and reduce
the number of pinconf instance when this feature is deactivated
(for arch stm32mp for example for SPL).
This patch allows to control this feature with a new option
CONFIG_PINCONF_RECURSIVE when it is possible for each individual
pin controller device.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fixed CONFIG_IF_ENABLED() condition, added __maybe_unused:
Signed-off-by: Simon Glass <sjg@chromium.org>
The power domain associated with a device is enabled when probing,
but currently the domain remains enabled when the device is removed.
Some boards started to disable power domains for selected devices
via custom board_quiesce_devices(), but it doesn't work in many
cases, i. e. because devices still can be accessed later in
.remove() callback on behalf of dm_remove_devices_flags().
Utilize the DM core to power off the device power domain, but add a
device flag to be able to selectively let the power domain enabled
after device removal. This might be required for devices that must
remain enabled when booting OS, i. e. serial console for debug
output, etc.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add dev_power_domain_off() api to disable all the power-domains
corresponding to a device
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable DM_FLAG_DEFAULT_PD_CTRL_OFF for arm64 remote core so that
pd can be enabled after loading the image.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In some remoteproc cases, enabling the power domain of the core will
start running the core. In such cases image should be loaded before
enabling the power domain. But the current DM framework enables the
power-domain by default during probe. This is causing the remotecore
to start and crash as there is no valid image loaded.
In order to avoid this introduce a DM flag that doesn't allow for
enabling/disabling the power-domain by DM framework.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Skip not associated gpio phandle let register the other gpios on a group.
We need anyway to send out a warning to the user to fix their uboot-board.dtsi.
Thhe handle id can be found inside the decompiled dtb
dtc -I dtb -O dts -o devicetree.dts spl/u-boot-spl.dtb
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When multiple power domains attached to a device, need power on
them all, so use dev_power_domain_on to do that.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add this new API to power on multiple domains attached
to a device.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Changed to static inline and added a condition into C file:
Signed-off-by: Simon Glass <sjg@chromium.org>
When CONFIG_OF_PRIOR_STAGE is enabled, this workaround was needed
before device_bind_common assigned request numbers sequentially in the
absence of aliases.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
For CONFIG_OF_PRIOR_STAGE, in the absence of a device tree alias for a
given device, use the next request number for that type of device.
This allows aliases to be used when they're available, while still
allowing unaliased devices to be probed.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
The reset function sets the pin to 0 then 1 but if the pin is marked
ACTIVE_LOW in the DT it gets inverted and leaves the TPM in reset.
Let the gpio driver take care of the reset polarity.
Signed-off-by: Kayla Theil <kayla.theil@mixed-mode.de>
In the Linux pinctrl binding, the pin configuration nodes don't need to
be direct children of the pin controller device (may be grandchildren for
example). This behavior is managed with the pinconfig u-class which
recursively bind all the sub-node of the pin controller.
But for some binding (when pin configuration is only children of pin
controller) that is not necessary. U-Boot can save memory and reduce
the number of pinconf instance when this feature is deactivated
(for arch stm32mp for example for SPL).
This patch allows to control this feature with a new option
CONFIG_PINCONF_RECURSIVE when it is possible for each individual
pin controller device.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
-------------------
Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/597498628
- logicpd pinmux
- i.MX7ULP: imx_ddr_size
- fixes Toradex i.MX6/i.MX7
- pico-imx7d
- tpc70 converted to DM
- New Board: meerkat96
- add HAB version command
- i.MX8 :
imx8: Jump from alias to OCRAM address at SPL init
imx8qm/qxp: Set SPL TEXT base to OCRAM base
-----BEGIN PGP SIGNATURE-----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=J8jd
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20191014' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20191014
-------------------
Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/597498628
- logicpd pinmux
- i.MX7ULP: imx_ddr_size
- fixes Toradex i.MX6/i.MX7
- pico-imx7d
- tpc70 converted to DM
- New Board: meerkat96
- add HAB version command
- i.MX8 :
imx8: Jump from alias to OCRAM address at SPL init
imx8qm/qxp: Set SPL TEXT base to OCRAM base
- Add sdhci driver for Broadcom iProc platform
- Add a driver callback for power-cycle for mmc
- Implement host_power_cycle callback for stm32_sdmmc2
- spl: dm_mmc: Initialize only the required mmc device
Support for Raydium RM68200 720p dsi 2dl video mode panel.
This rm68200 panel driver is based on the Linux Kernel driver from
drivers/gpu/drm/panel/panel-raydium-rm68200.c.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Add a Synopsys Designware MIPI DSI host bridge driver, based on the
Rockchip version from rockchip/dw-mipi-dsi.c with phy & bridge APIs.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Display Serial Interface (DSI) host can usefully be modelled
as their own uclass.
DSI defines a serial bus and a communication protocol
between the host and the device (panel, bridge).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Mipi_display.c contains a set of dsi helpers.
This file is a copy of file drm_mipi_dsi.c (linux kernel).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Add support for CDCE913/925/937/949 family of devices. These are modular
PLL-based low cost, high performance, programmable clock synthesizers,
multipliers and dividers. They generate up to 9 output clocks from a
single input frequency. The initial version of the driver does not
support programming of the PLLs, and thus they run in the bypass mode
only. The code is loosely based on the linux kernel cdce9xx driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Power-domain is enabled by default in device_probe. am654 mmc driver
is enabling power-domain again in probe. As the second call is
redundant, drop power_domain_on from probe.
Tested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Regulator should not be enabled at probe time if regulator-boot-on
property is not in the dt node.
"enable-active-high" property is only used to indicate the GPIO
polarity.
See kernel documentation :
- Documentation/devicetree/bindings/regulator/fixed-regulator.yaml
- Documentation/devicetree/bindings/regulator/gpio-regulator.yaml
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In 32bits mode upper bits need to be set to 0, otherwise controller will
try to DMA into not existing memory and stops with error.
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Oleksandr Rybalko <ray@ddteam.net>
The driver provides PHY for USB2, USB3.0, PCIe and SATA, and now
we just enable PCIe. As for the other functionalities will be
added gradually in upcoming days.
This is adapted from the Linux version.
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
This adds PCIe controller support for MT7623.
This is adapted from the Linux version.
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
The Broadcom ARM implementations do not yet have a clock framework so
one can use a fixed clock as the root clock of the hsspi block. The
fixed clock does not have an "enable" routine, since it's always
enabled. So when we hit this issue, getting an ENOSYS return, do not
bail but continue initialization.
Similarly the block might already have been out of reset, say, when
we are booting from a SPI device. So if the reset signal is not configured
in the device tree, do not bail out and instead skip deasserting the reset.
Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Make the driver compatible with both big and little endian SOCs.
Replace big-endian calls with their raw equivalents, expect for
writing the command to FIFO. That still has to be in big-endian
format.
Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This IP exists in both MIPS and ARM cores, so we also
allow to use this driver on bcm6858 and bcm63158.
Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Certain SoCs with K3 architecture have integrated a C66 Corepac DSP
subsystem and an advanced C71 DSPs. Introduce a remoteproc driver
that that does take care of loading an elf to any of the specified
DSPs and start it.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
SoCs with K3 architecture have an integrated Arm Cortex-R5F subsystem
that is comprised of dual-core Arm Cortex-R5F processor cores. This R5
subsytem can be configured at boot time to be either run in a LockStep
mode or in an Asymmetric Multi Processing (AMP) fashion in Split-mode.
This subsystem has each Tightly-Coupled Memory (TCM) internal memories
for each core split between two banks - TCMA and TCMB.
Add a remoteproc driver to support this subsystem to be able to load
and boot the R5 cores primarily in LockStep mode or split mode.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Power domain for the remote cores needs to be handled in a right
sequence as mandated by the spec. Introduce tisci helper apis
that can control power-domains of remote cores. TISCI clients
can use this api and control the remote cores power domain instead
of hooking it to power-domain layer.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Introduce rproc_elf_get_boot_addr() that returns the entry point of
the elf file. This api auto detects the 64/32 bit elf file and returns
the boot addr accordingly.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Introduce a common remoteproc elf loader and checker functions that
automatically detects the 64 bit elf file or 32 bit elf file and
loads/checks the sections accordingly.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
The current rproc-elf-loader supports loading of only 32 bit elf files.
Introduce support for loading of 64 bit elf files in rproc-elf-loader.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
rproc_elf32_load_image() rely on user to send a valid address for elf loading.
Instead do a sanity check on the address passed by user. This will help
all rproc elf users to not call sanity_check explicitly before calling
elf_loading.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Introduce a new parameter "size" that accepts size of the region to
remoteproc ops callback device_to_virt(). This can enforce more checks
on the region that device_to_virt() is dealing with.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Fabien Dessenne <fabien.dessenne@st.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Add a field to the PCI emulator per-device data which records which device
is being emulated. This is useful when the emulator needs to check the
device for something.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: rebase the patch against u-boot-x86/master to get it applied cleanly]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
For the correct power cycle sequence with stm32_sdmmc2, the write of the
power cycle value in PWRCTL field of SDMMC_POWER register is now done in
stm32_sdmmc2_host_power_cycle() and no more in stm32_sdmmc2_pwrcycle().
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Some MMC peripherals require specific power cycle sequence, where some
registers need to be written between the regulator is turned off and then
back on. This is the case for the MMC IP embedded in STM32MP1 SoC.
In STM32MP157 reference manual [1], the power cycle sequence is:
1. Reset the SDMMC with the RCC.SDMMCxRST register bit. This will reset
the SDMMC to the reset state and the CPSM and DPSM to the Idle state.
2. Disable the Vcc power to the card.
3. Set the SDMMC in power-cycle state. This will make that the
SDMMC_D[7:0], SDMMC_CMD and SDMMC_CK are driven low, to prevent the card
from being supplied through the signal lines.
4. After minimum 1ms enable the Vcc power to the card.
5. After the power ramp period set the SDMMC to the power-off state for
minimum 1ms. The SDMMC_D[7:0], SDMMC_CMD and SDMMC_CK are set to
drive “1”.
6. After the 1ms delay set the SDMMC to power-on state in which the
SDMMC_CK clock will be enabled.
7. After 74 SDMMC_CK cycles the first command can be sent to the card.
The step 3. cannot be handled by the current framework implementation.
A new callback (host_power_cycle) is created, and called in
mmc_power_cycle(), after mmc_power_off().
The incorrect power cycle sequence has shown some boot failures on
STM32MP1 with some SD-cards, especially on cold boots when the input
frequency is low (<= 25MHz).
Those failures are no more seen with this correct power cycle sequence.
[1] https://www.st.com/resource/en/reference_manual/DM00327659.pdf
Signed-off-by: Yann Gautier <yann.gautier@st.com>
In SPL, all the available mmc devices gets initialized during boot.
This might not work in cases where clocks are not available for
certain mmc devices(other than boot device) and the support for
enabling device might not be ready.
Texas Instruments' K3 J721E device having a central system controller
(dmsc) is one such example falling in this category. Below is the
sequence for the failing scenario:
- ROM comes up in SD mode and loads SPL by just initialing SD card.
- SPL loads dmsc firmware from SD Card.
Since ROM has enabled SD, SPL need not enable the SD, just need
to re initialize the card. But SPL is trying to initialize other MMC
instances which are in disabled state. Since dmsc firmware is not yet
available, devices cannot be enabled. So in SPL, initialize only the
mmc device that is needed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
- Rename existing FSP code to fsp1
- Add fsp2 directory in preparation to support FSP 2.0
- Various x86 platform codes update
- Various bug fixes and updates in dm core, sandbox and spl
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdnCy/AAoJEB6zHgIOrC/Izp4IAJVDE0oyOYcwBoCsAqa8zvMJ
/G815T1TGyc6674TQ+Px47t+1O9InClag576E1ttKVSZHnTqH9AW1aGdVqYFgmwu
bbk7a/N2bSYc1ZruiH1YMzwVMTmwaIvn9cvNeBMkQ0cXBP6R7m9DsupaTG9mNsll
7wNFF6gZCOXQEOL6hgxerxr6UM2xaQMpSqfYhfYfmHyU0S86Cr1J7dORL1MHhZ4/
WLVuxCPpgeTwiZ0i9TerC0eH0agPQ2dmtDPAQFn+RihVS29YNDTaR+a4XVKJJ6hs
Y/77d0JYmPSY5JgYLAdjqx+GQKKqy9kpdHJz+sXCiolDdYHmG3c+4zQzrLzkH+k=
=Y0qG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2020.01-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features and fixes for 2020.01 cycle
The feature set includes support for two new boards from Microchip AT91:
The sama5d27_wlsom1_ek , an evaluation kit which includes the SAMA5D2
SOC packaged in a 256 MB LPDDR2 SIP, on a SOM including wireless, which
is placed on evaluation kit with sd-card, ethernet, LCD, Camera sensor,
QSPI, etc
The sam9x60ek, an evaluation kit for the new SoC based on ARM926j , the
SAM9X60 . The evaluation kit includes NAND flash, QSPI, Ethernet, Audio,
Camera sensor connector, etc.
The full support for sam9x60ek will come at a later time. There are
still missing bits regarding the clock support and power management
controller.
The major corrections in this pull request are:
Fixes for the SetVariable() boot service.
Device path node for NVMe drives.
Disable CONFIG_CMD_NVEDIT by default.
-----BEGIN PGP SIGNATURE-----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=nzgb
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-01-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-01-rc1
The major corrections in this pull request are:
Fixes for the SetVariable() boot service.
Device path node for NVMe drives.
Disable CONFIG_CMD_NVEDIT by default.
For NXP SoCs we have to set pinmux configuration ASAP (ideally
before relocation) to get serial console working. Without this we miss
almost the half of output (U-boot version, CPU defails, Reset cause,
DRAM details etc.).
To achieve this we need to force appropriate pinctrl drivers to get
probed before relocation.
Fixes: cd69e8ef9b ("colibri-imx6ull: migrate pinctrl and regulators to dtb/dm")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
On, i.MX8MQ, the PLL config must be done when ddrmix
isolation is released. So move the dram pll init after
iso config done. For other i.MX8M SOC, either init pll
before or after isolation is ok.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Refine the ddr init driver to make it more reusable for different
DDR type(LPDDR4, DDR4 & DDR3L). So we can reduce some redundant
code.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update the ddrc Qos setting for B1 to align with B0's setting.
Correct the initial clock for dram_pll. This setting will be
overwrite before ddr phy training. Although there is no impact
on the dram init, we still need to correct it to eliminate
confusion.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Tested-by: Robby Cai <robby.cai@nxp.com>
Since the parameter of dram_pll_init is changed, update to use new.
Also remove non-existed header file.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The write data size can be overwritten by writing to the IDATSZ
field of IPCR register. Since the driver always updates the IDATSZ
in page program operation. Set the LUT data size to 0 to align
the codes with iMX.
Signed-off-by: Ye Li <ye.li@nxp.com>
On latest iMX platforms like iMX7D/iMX6UL/iMX8MQ, the QSPI controller
is updated to have TDH field in FLSHCR register. According to reference
manual, this TDH must be set to 1 when DDR_EN is set. Otherwise, the TX
DDR delay logic won't be enabled.
Another issue in DDR mode is the MCR register will be overwritten in
every read/write/erase operation. This causes DDR_EN been cleared while
TDH=1, then no clk2x output for TX data shift and all operations will
fail.
Signed-off-by: Ye Li <ye.li@nxp.com>
With CONFIG_SPL_OF_CONTROL, the device tree will be padded to
end of the u-boot-spl-nodtb.bin, however we also put
the ddr firmware file to this location, so need to adapt
the code with SPL OF and align to 4 bytes to ease copy firmware.
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add support for the reset controller that's used on the i.MX7D
and i.MX8MQ. This will be needed to be able to assert the PCIe
reset pins. Bindings taken from Linux, driver implementation
mostly taken from Linux and adjusted to U-Boot infrastructure.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add support for the power domain controller that's used on the
i.MX8MQ. This will be needed to be able to power on the PCIe
controller. Bindings taken from Linux, driver implementation
taken from the i.MX8 power domain controller and adjusted for
the i.MX8M SoC.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
After this patch the mxs_gpio.c DM/DTS driver can be used at early SPL to
read states of gpio pins (and for example alter the boot flow).
It was necessary to adjust its name to 'fsl_imx_2{38}_gpio' to match
requirements for SPL_OF_PLATDATA usage.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This change replaces printf() with debug() for the notification about
commands timeouts.
This is done on purpose (also other drivers use such approach - dw_mmc.c,
mvebu_mmc.c), as the mmc core code (mmc.c) uses timeouts to assess if one
is using sd card or eMMC device.
In such situation timeout is a some kind of a "normal" behavior and there
shall not be any output to the console.
There is no impact on boot time for boards using this driver (even in SPL)
when two extra timeouts are returned (no SD card present, only eMMC
available).
Boot time tested with grabserial:
sudo grabserial -b 115200 -d /dev/ttyUSB1 -e 30 -t -m "^U-Boot SPL*"
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch converts the mxsmmc driver to support DM/DTS.
Moreover, it is also possible to use it in early SPL with
SPL_OF_PLATDATA enabled.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
After this patch the mxs_spi.c DM/DTS driver can be used at early SPL to
read payload from SPI-NOR memories.
It was necessary to adjust its name to 'fsl_imx_2{38}_spi' to match
requirements for SPL_OF_PLATDATA usage.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Without this change the DM/DTS version of mxs_spi driver doesn't reset the
SPI IP block in probe.
As a result this driver (when used solely on U-Boot proper) relies on reset
performed by mxs spi driver in SPL.
In the use case where eMMC is used in SPL as a boot primary device, the
mxs_reset_block() is not called at all and DM/DTS aware SPI driver in
U-Boot proper is malfunctioning.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This change initializes proper member of struct driver -
platdata_auto_alloc_size instead of priv_auto_alloc_size, which is setup
twice.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Add sc_pm_is_partition_started to check whether a partition
has been started. This will be used to detect M4 partition booted up or
not, then we could choose which dtb to use. If M4 is up, we need
use dtb, such as imx8qm-mek-rpmsg.dtb.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX7 and i.MX8M use mxc uart driver, so let's make the SoC could
use MXC_UART kconfig.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
fdtdec_get_addr_size could not parse addr/size correctly is
using address-cells 2 and size-cells 2 on an ARM32 SoC.
So switch to use devfdt_get_addr_size_index.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With new mailbox driver PMUFW configuration object can be loaded via the
same interface and there is no need to have pmu_ipc.c completely.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
U-Boot running in EL3 can't use SMC that's why there is a need to talk to
PMUFW directly via mailbox. The same logic is applied to all functions
which need to talk to PMUFW that's why move this logic to separate function
to avoid code duplication.
Also SMC request ID can be composed from PM_SIP_SVC offset that's why
ZYNQMP_SIP_SVC_GET_API_VERSION macro can be removed completely.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use the new function from firmware version to get the firmware version.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
New firmware header to place firmware specific macro and function
declarations. The patch also moves the macros defining PM operations as
well as some helper macros.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Implements the function to get PMU Firmware version using the mailbox
driver or smc call based on if running SPL or not. Additionally gets
version as part of the ZynqMP Firmware driver probing
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
zynqmp-power driver for ZynqMP to handle the communication with the PMU
firmware. Firmware driver just probes subnodes and power driver handles
communication with PMU using the IPI mailbox driver.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP mailbox driver implementing IPI communication with PMU. This would
allow U-Boot SPL to communicate with PMUFW to request privileged
operations.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The following patch allows the mailbox node in DT to host subnodes with
mailbox definitions. If the client phandle to the mailbox is not the
mailbox driver node, just checks parents as well.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Check if request and free operations are present prior calling to the
functions.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch assings the phynode pointer to the phydev node as it is needed
later in the corresponding phy driver to read phy properties from DT.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch fixes zynq_gpio_direction() to call driver specific
zynq_gpio_set_value function rather than top level gpio_set_value.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Phy setup should be done before dwc3 soft core reset as it is done
in linux & this fixes unreliable detection of usb cable on host side.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The zynq_sdhci drivers depends on DM_MMC in Kconfig so no need to check for
DM_MMC in the driver so this patch removes it.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for gmiitorgmii converter.
This converter sits between the MAC and the external phy
MAC <==> GMII2RGMII <==> RGMII_PHY.
The ethernet driver probes this bridge and this bridge driver
probes real phy driver and invokes the real phy functionalities
as requested. This bridge just needs to be configured based on
real phy negotiated speed and duplex.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch define init routine for generic phy driver and registers it
using phy_register as this generic phy driver also needs to be relocated
incase of manual reloc.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch removes check for Versal platform
in gem driver as it now supports clock setting
through clock framework.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
