Instead of trying to guess which operating modes need in-band
negotiation to be active and which ones don't, parse the available
information from the device tree. That will be correct in the cases we
can already guess, and more.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The Freescale TSEC can be a DSA master, and the ports of the attached
DSA switch can have different MAC addresses compared to the TSEC.
Nonetheless, the TSEC must receive the packets on behalf of those switch
ports. Therefore, implement the promiscuous mode method to allow DSA to
set this.
Note that the init_registers() function called from eth_ops :: start
overwrites this setting. There is no reason why the RCTRL register
should be zero-initialized, so just stop clearing it so that the setting
we applied in eth_ops :: set_promisc sticks.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The VSC8502 is a Microchip (formerly Microsemi, formerly Vitesse)
dual port, gigabit Ethernet copper PHY which supports the MII, GMII and
RGMII MAC-side interfaces.
Of these, I could only test RGMII, and my board needed RGMII delays to
be applied by software, so I am able to confirm that this patch handles
that properly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
sdhci:
- Fix emmc mini case with missing firmware interface
zynqmp:
- Restore JTAG interface if required
- Allow overriding board name
- Add support for DLC21
- Fix one fallthrought statement description
- Use config macro instead of name duplication
- Save multiboot to variable
firmware:
- Handle ipi_req errors better
- Use local buffer in case user doesn't need it instead of NULL/0 location
spi:
- gqsi: Fix write issue at low frequencies
net:
- gem: Disable broadcasts
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYZPDrwAKCRDKSWXLKUoM
IS9GAJ93T/uprhLcKWMb+284YMb2caWgOACfZ02nTlzvZKNNXVretJgZaHXqj1M=
=cwTL
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.01-rc3' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.01-rc3
sdhci:
- Fix emmc mini case with missing firmware interface
zynqmp:
- Restore JTAG interface if required
- Allow overriding board name
- Add support for DLC21
- Fix one fallthrought statement description
- Use config macro instead of name duplication
- Save multiboot to variable
firmware:
- Handle ipi_req errors better
- Use local buffer in case user doesn't need it instead of NULL/0 location
spi:
- gqsi: Fix write issue at low frequencies
net:
- gem: Disable broadcasts
Use moveconfig.py script to convert CONFIG_SYS_FMAN_FW_ADDR,
CONFIG_SYS_QE_FW_ADDR and CONFIG_SYS_QE_FMAN_FW_LENGTH to Kconfig and
move these entries to defconfigs.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The following warning is seen in macb.c in a 32-bit build:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Change to use dev_read_addr_index_ptr(), or cast with uintptr_t.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
As part of migrating to DM_GPIO and DM_PINCTRL, eventually we will
remove the asm/arch/gpio.h header. In preparation, clean up the various
files that include it.
Some files did not contain any GPIO code at all, so this header was
completely unused.
A few files contained only legacy platform-specific GPIO code for
setting up pin muxes. They were left unchanged, as that code will be
completely removed by the DM_PINCTRL migration.
The remaining files contain some combination of DM_GPIO and legacy GPIO
code. For those, switch to including asm/gpio.h (if it wasn't included
already). Right now, this header provides both sets of functions,
because ARCH_SUNXI selects GPIO_EXTRA_HEADER. This will still be the
right header to include once the DM_GPIO migration is complete and
GPIO_EXTRA_HEADER is no longer needed.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last ARCH_MX25 platform, remove those
references as well.
Cc: Matthias Weisser <weisserm@arcor.de>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
These functions can return errors, it's best to catch them and trigger
the driver unwind code path.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The two should be equivalent, but at the moment some platforms
(ls1021a-tsn.dts) use phy-mode only, which is not parsed.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Currently the init_phy function may overwrite the priv->interface
property, since it calls tsec_get_interface which tries to determine it
dynamically based on default register values in ECNTRL.
Let's do that only if phy-connection-type happens to not be defined in
the device tree.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The felix driver runs only on NXP LS1028A, which most definitely does
not support the parallel 10G interface, just USXGMII, and that only up
to 2.5Gbps (toned down from 10 Gbps via symbol replication).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The enetc driver runs only on NXP LS1028A, which most definitely does
not support the parallel 10G interface, just USXGMII, and that only up
to 2.5Gbps (toned down from 10 Gbps via symbol replication).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
After the discussion here:
https://lore.kernel.org/netdev/20210603143453.if7hgifupx5k433b@pali/
which resulted in this patch:
https://patchwork.kernel.org/project/netdevbpf/patch/20210704134325.24842-1-pali@kernel.org/
and many other discussions before it, notably:
https://patchwork.kernel.org/project/linux-arm-kernel/patch/1512016235-15909-1-git-send-email-Bhaskar.Upadhaya@nxp.com/
it became apparent that nobody really knows what "SGMII 2500" is.
Certainly, Freescale/NXP hardware engineers name this protocol
"SGMII 2500" in the reference manuals, but the PCS devices do not
support any "SGMII" specific features when operating at the speed of
2500 Mbps, no in-band autoneg and no speed change via symbol replication
. So that leaves a fixed speed of 2500 Mbps using a coding of 8b/10b
with a SERDES lane frequency of 3.125 GHz. In fact, "SGMII 2500 without
in-band autoneg and at a fixed speed" is indistinguishable from
"2500base-x without in-band autoneg", which is precisely what these NXP
devices support.
So it just appears that "SGMII 2500" is an unclear name with no clear
definition that stuck.
As such, in the Linux kernel, the drivers which use this SERDES protocol
use the 2500base-x phy-mode.
This patch converts U-Boot to use 2500base-x too, or at least, as much
as it can.
Note that I would have really liked to delete PHY_INTERFACE_MODE_SGMII_2500
completely, but the mvpp2 driver seems to even distinguish between SGMII
2500 and 2500base-X. Namely, it enables in-band autoneg for one but not
the other, and forces flow control for one but not the other. This goes
back to the idea that maybe 2500base-X is a fiber protocol and SGMII-2500
is an MII protocol (connects a MAC to a PHY such as Aquantia), but the
two are practically indistinguishable through everything except use case.
NXP devices can support both use cases through an identical configuration,
for example RX flow control can be unconditionally enabled in order to
support rate adaptation performed by an Aquantia PHY. At least I can
find no indication in online documents published by Cisco which would
point towards "SGMII-2500" being an actual standard with an actual
definition, so I cannot say "yes, NXP devices support it".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
To avoid a warning with W=1 about this function not having a previous
prototype, declare it as static, because it is not used outside of this
translation module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
NXP Legal insists that the following are not fine:
- Saying "NXP Semiconductors" instead of "NXP", since the company's
registered name is "NXP"
- Putting a "(c)" sign in the copyright string
- Putting a comma in the copyright string
The only accepted copyright string format is "Copyright <year-range> NXP".
This patch changes the copyright headers in the networking files that
were sent by me, or derived from code sent by me.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Make sure that the link status returned by phy_startup() is propagated
to the .start() method of struct eth_ops.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tested-by: Michael Walle <michael@walle.cc>
It is an unfortunate reality that some PHY settings done by U-Boot
persist even after the PHY is reset and taken over by Linux, and even
more unfortunate that Linux has come to depend on things being set in a
certain way.
For example, on the NXP LS1028A-RDB, the felix switch ports are
connected to a VSC8514 QSGMII PHY. Between the switch port PCS and the
PHY, the U-Boot drivers enable in-band auto-negotiation which makes the
copper-side negotiated speed and duplex be transmitted from the PHY to
the MAC automatically.
The PHY driver portion that does this is in vsc8514_config():
/* Enable Serdes Auto-negotiation */
phy_write(phydev, MDIO_DEVAD_NONE, PHY_EXT_PAGE_ACCESS,
PHY_EXT_PAGE_ACCESS_EXTENDED3);
val = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_VSC8514_MAC_SERDES_CON);
val = val | MIIM_VSC8574_MAC_SERDES_ANEG;
phy_write(phydev, MDIO_DEVAD_NONE, MIIM_VSC8514_MAC_SERDES_CON, val);
The point is that in-band autoneg should be turned on in both the PHY
and the MAC, or off in both the PHY and the MAC, otherwise the QSGMII
link will be broken.
And because phy_config() is currently called at .port_enable() time, the
result is that ports on which traffic has been sent in U-Boot will have
in-band autoneg enabled, and the rest won't.
It can be argued that the Linux kernel should not assume one way or
another and just reinitialize everything according to what it expects,
and that is completely fair. In fact, I've already started an attempt to
remove this dependency, although admittedly I am making slow progress at
it:
https://patchwork.kernel.org/project/netdevbpf/cover/20210212172341.3489046-1-olteanv@gmail.com/
Nonetheless, the sad reality is that NXP also has, apart from kernel
drivers, some user space networking (DPDK), and for some reason, the
expectation there is that somebody else initializes the PHYs. The kernel
can't do it because the device ownership doesn't belong to the kernel,
so what remains is for the bootloader to do it (especially since other
drivers generally call phy_config() at probe time). This is a really
weak guarantee that might break at any time, but apparently that is
enough for some.
Since initializing the ports and PHYs at probe time does not break
anything, we can just do that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tested-by: Michael Walle <michael@walle.cc>
No one is calling this function from outside felix_switch.c.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tested-by: Michael Walle <michael@walle.cc>
Non DM builds fail with the following error:
drivers/net/tsec.c:641:24: error: 'tsec_get_interface' defined but not used [-Werror=unused-function]
641 | static phy_interface_t tsec_get_interface(struct tsec_private *priv)
Fix that.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
The code under drivers/net is related to ethernet networking drivers, in
some fashion or another. Drop these from the top-level Makefile and
also move the phy rule into drivers/net/Makefile which is where it
belongs. Make the new rule for drivers/net check for the build-stage
relevant ETH symbol.
Fix up some Kconfig dependencies while we're here to mirror how the
Makefile logic now works.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Introduce ETH, Kconfig dependency changes, am43xx fix]
Signed-off-by: Tom Rini <trini@konsulko.com>
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support for boards supporting TFA boot separately in cortina
firmware. Please note, a weak function is defined to retrieve firmware
address values as CONFIG_CORTINA_FW_ADDR is now defined in defconfig and
can only have one possible value defined. This weak function will help
in overwrting the values to get proper addresses as per boot source.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Use moveconfig.py script to convert below defines to Kconfig and move
these entries to defconfigs.
CONFIG_CORTINA_FW_ADDR
CONFIG_CORTINA_FW_LENGTH
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
It is a pain to have to specify the value 10 in each call. Add a new
dectoul() function and update the code to use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is a pain to have to specify the value 16 in each call. Add a new
hextoul() function and update the code to use it.
Add a proper comment to simple_strtoul() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for xilinx multirate(MRMAC) ethernet driver.
This driver uses multichannel DMA(MCDMA) for data transfers of MRMAC.
Added support for 4 ports of MRMAC for speeds 10G and 25G.
MCDMA supports upto 16 channels but in this driver we have setup only
one channel which is enough.
Tested 10G and 25G on all 4 ports.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Since the SCBM SMMU is not only connected to the NETSEC
but also shared with the F_SDH30 (eMMC controller), that
should be initialized at board level instead of NETSEC.
Move the SMMU initialization code into board support
and call it from board_init().
Without this fix, if the NETSEC is disabled, the Linux
eMMC ADMA cause an error because SMMU is not initialized.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
The result of dpio_close() is actually taken into account.
Signed-off-by: Cosmin-Florin Aluchenesei <aluchenesei.cosmin-florin@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Change the reg variable to not be unsigned so that we not get into an
unsigned compared against 0.
Signed-off-by: Cosmin-Florin Aluchenesei <aluchenesei.cosmin-florin@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Define LOG_CATEGORY to allow filtering with log command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Define LOG_CATEGORY to allow filtering with log command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add a common empty ops: eqos_null_ops() to remove the duplicated empty
functions and reduce the driver size for stm32 and imx config.
This patch also aligns the prototype of ops 'eqos_stop_clks' with other
eqos ops by adding return value.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Use the generic ethernet phy which already manages the correct binding
for gpio reset, including the assert an deassert delays.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Since the commit commit 6a895d039b ("net: Update eQos driver and FEC
driver to use eth phy interfaces") the field phyaddr of driver private data
struct eqos_priv is no more used in eqos_start() for the phy_connect()
parameter.
Now this variable is only initialized in eqos_probe_resources_stm32()
it can be removed.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Bind any subnode with name beginning by mdio, mdio0 for example,
and not only the "mdio" as namei of subnode.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Replace debug trace and printf to log macros:
- debug() replaced by dev_dbg() when device is available, this macro
indicate the device name since commit ceb70bb870 ("dm: Print device
name in dev_xxx like Linux")
- printf() replaced by log_notice() to allow dispatch to log backends.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The gpio reset and the assert or deassert delay are defined in generic
binding of the ethernet phy in Linux:
Documentation/devicetree/bindings/net/ethernet-phy.yaml
reset-gpios:
maxItems: 1
description:
The GPIO phandle and specifier for the PHY reset signal.
reset-assert-us:
description:
Delay after the reset was asserted in microseconds. If this
property is missing the delay will be skipped.
reset-deassert-us:
description:
Delay after the reset was deasserted in microseconds. If
this property is missing the delay will be skipped.
See also U-Boot: doc/device-tree-bindings/net/phy.txt
This patch adds the parsing of this common DT properties in the
u-class "eth_phy_generic", used by default in the associated driver
"eth_phy_generic_drv"
This parsing function eth_phy_of_to_plat can be reused by other
ethernet phy drivers for this uclass UCLASS_ETH_PHY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Use same type as eth_device->iobase and support addresses greater
than INT_MAX.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. As this is also the last in family remove the related
support as well.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
At present if ifname is exactly IFNAMSIZ characters then it will result
in an unterminated string. Fix this by using strlcpy() instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Coverity (CID: 316358)
Acked-by: Ramon Fried <rfried.dev@gmail.com>
The Microchip KSZ9477/KSZ9897/KSZ9567 7-Port Gigabit Ethernet Switches
support SGMII/RGMII/MII/RMII with register access via SPI, I2C, or MDIO.
This driver currently supports I2C register access but SPI or MDIO register
access can be easily added at a later time.
Tagging is not implemented and instead the active port is tracked to
avoid needing a tag to store port information.
This was tested with the imx8mm-venice-gw7901 board which has a
KSZ9897S switch with an IMX8MM FEC MAC master connected via RGMII_ID.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Enabling promiscuous mode is necessary if FEC is the master of a DSA
switch driver where each port has their own MAC address.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
If the FEC is connected to a fixed-link (upstream switch port for
example) the phy_of_node should be set to the fixed-link node
so that speed and other properties can be found properly.
In addition fix a typo in the debug string.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
When using uclass_get_device* to get the FEC device we need to use
device sequence instead of index into UCLASS_ETH. In systems where for
example a I2C based DSA switch exists it will probe before the FEC
master and its ports will be registered first and have the first
indexes yet the FEC's sequence comes from the device-tree alias.
Take for example the imx8mm-venice-gw7901 board which has an i2c based
DSA switch:
u-boot=> net list
eth1 : lan1 00:0d:8d:aa:00:2f
eth2 : lan2 00:0d:8d:aa:00:30
eth3 : lan3 00:0d:8d:aa:00:31
eth4 : lan4 00:0d:8d:aa:00:32
eth0 : ethernet@30be0000 00:0d:8d:aa:00:2e active
Thus in this case uclass_get_device(UCLASS_ETH, 0, &dev) returns lan1
which is wrong but uclass_get_device_seq(UCLASS_ETH, 0, &dev) returns
ethernet@30be000 which is correct.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the last
ARCH_T4160 platform, remove that support as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
the only ARCH_T1023 platform left, remove that support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These board has not been converted to CONFIG_DM_PCI by the deadline.
Remove them. As this is the last of the mcf547x_8x family of boards,
remove that support as well.
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove the define EQOS_DESCRIPTOR_ALIGN unused since the
commit 6f1e668d96 ("net: dwc_eth_qos: Pad descriptors to cacheline size")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Make sure that errors in the PHY driver .startup() method, such as no
link, are propagated and not ignored.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The RGMII spec supports optional in-band status reporting for the speed
and duplex negotiated on the copper side, and the ENETC driver enables
this feature by default.
However, this does not work when the PHY does not implement the in-band
reporting, or when there is a MAC-to-MAC connection described using a
fixed-link. In that case, it would be better to disable the feature in
the ENETC MAC and always force the speed and duplex to the values that
were negotiated and retrieved over MDIO once the autoneg is finished.
Since this works always, we just do it unconditionally and drop the
in-band code.
Note that because we need to wait for the autoneg to complete, we need
to move enetc_setup_mac_iface() after phy_startup() returns, and then
pass the phydev pointer all the way to enetc_init_rgmii().
The same considerations have led to a similar Linux driver patch as well:
https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git/commit/?id=c76a97218dcbb2cb7cec1404ace43ef96c87d874
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Given that even a fixed-link has an associated phy_device, there is no
reason to operate in a mode when dm_eth_phy_connect fails.
Remove the driver checks for a NULL priv->phy and just return -ENODEV
when that happens.
Copyright updated according to corporate requirements.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The SMC911x Ethernet MACs can be integrated using a 16 or 32-bit bus.
The driver needs to know about this choice, which is the reason for us
having a Kconfig symbol for that.
Now this bus width is already described using a devicetree property, and
since the driver is DM compliant and is using the DT now, we should query
this at runtime. We leave the Kconfig choice around, in case the DT is
missing this property.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The SMC911x Ethernet driver needs to know which accessor functions it
can use to access the MMIO registers. For that reason we have a Kconfig
choice between 16 and 32-bit bus width.
Since it's only those two options that we (and the Linux kernel)
support, and there does not seem to be any evidence of another bus
width anywhere, limit the Kconfig construct to a simple symbol.
This simplifies the code and allows a later rework to be much easier.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
clk:
- Add driver for Xilinx Clocking Wizard IP
fdt:
- Also record architecture in /fit-images
net:
- Fix plat/priv data handling in axi emac
- Add support for 10G/25G speeds
pca953x:
- Add missing dependency on i2c
serial:
- Fix dependencies for DEBUG uart for pl010/pl011
- Add setconfig option for cadence serial driver
watchdog:
- Add cadence wdt expire now function
zynq:
- Update DT bindings to reflect the latest state and descriptions
zynqmp:
- Update DT bindings to reflect the latest state and descriptions
- SPL: Add support for ECC DRAM initialization
- Fix R5 core 1 handling logic
- Enable firmware driver for mini configurations
- Enable secure boot, regulators, wdt
- Add support xck devices and 67dr
- Add psu init for sm/smk-k26 SOMs
- Add handling for MMC seq number via mmc_get_env_dev()
- Handle reserved memory locations
- Add support for u-boot.itb generation for secure OS
- Handle BL32 handoffs for secure OS
- Add support for 64bit addresses for u-boot.its generation
- Change eeprom handling via nvmem aliases
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYN105QAKCRDKSWXLKUoM
IZiFAJ9CIiEpHiBbnAhA0VOMGoaXHGULywCdED/5dNgVtc1C7y4avzETbEyWzD4=
=CdMa
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.10' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.10
clk:
- Add driver for Xilinx Clocking Wizard IP
fdt:
- Also record architecture in /fit-images
net:
- Fix plat/priv data handling in axi emac
- Add support for 10G/25G speeds
pca953x:
- Add missing dependency on i2c
serial:
- Fix dependencies for DEBUG uart for pl010/pl011
- Add setconfig option for cadence serial driver
watchdog:
- Add cadence wdt expire now function
zynq:
- Update DT bindings to reflect the latest state and descriptions
zynqmp:
- Update DT bindings to reflect the latest state and descriptions
- SPL: Add support for ECC DRAM initialization
- Fix R5 core 1 handling logic
- Enable firmware driver for mini configurations
- Enable secure boot, regulators, wdt
- Add support xck devices and 67dr
- Add psu init for sm/smk-k26 SOMs
- Add handling for MMC seq number via mmc_get_env_dev()
- Handle reserved memory locations
- Add support for u-boot.itb generation for secure OS
- Handle BL32 handoffs for secure OS
- Add support for 64bit addresses for u-boot.its generation
- Change eeprom handling via nvmem aliases
Add support for 10G/25G (XXV) high speed ethernet. This Makes use of
the exiting AXI DMA, similar to 1G.
Signed-off-by: Alessandro Temil <atemil@waymo.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There are lot of accesses to priv data in of_to_plat(), which is incorrect.
Create a platform data structure and use it in of_to_plat(), then copy all
platform data to priv data in probe.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
clean up octeontx_smi_probe by using the live-tree API.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Commit 4f0278dac5 ("net: sun8i-emac: Lower MDIO frequency") leads to
network failure on the OrangePi PC.
=> dhcp
sun8i_emac_eth_start: Timeout
According to the commit message the change of the MDIO frequency is only
required for external PHYs.
Fixes: 4f0278dac5 ("net: sun8i-emac: Lower MDIO frequency")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add SynQuacer's NETSEC GbE controller driver.
Since this driver will load the firmware from SPI NOR flash,
this depends on CONFIG_SYNQUACER_SPI=y.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Revert some changes of commit 3a97da12ee ("net: dwc_eth_qos: add dwc
eqos for imx support") that were probably added by mistake.
One of these changes can lead to received data corruption (enabling
FUP and FEP bits). Another causes invalid register rxq_ctrl0 settings
for some platforms. And another makes some writes at unknown memory
location.
Fixes: 3a97da12ee ("net: dwc_eth_qos: add dwc eqos for imx support")
Signed-off-by: Daniil Stas <daniil.stas@posteo.net>
Cc: Ye Li <ye.li@nxp.com>
Cc: Fugang Duan <fugang.duan@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Disabling clk_ck clock leads to link up status loss in phy, which
leads to auto-negotiation restart before each network command
execution.
This issue is especially big for PXE boot protocol because of
auto-negotiation restarts before each configuration filename trial.
To avoid this issue don't disable clk_ck clock after it was enabled.
Signed-off-by: Daniil Stas <daniil.stas@posteo.net>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
commit f1bcad22dd ("net: e1000: add support for writing to EEPROM")
adds support for storing hwaddr in EEPROM however i210 devices do not
support this and thus results in errors such as:
Warning: e1000#0 failed to set MAC address'
Check if a flash device is present and if not return -ENOSYS indicating
this is not supported.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Current tsec adapter sets adapter gigabit capabilities by default, and in
reality this must not always be the case.
It is possible that tsec adapter is used for 100Mbps connection, and in
this case setting 1000Mbps capabilities can lead to some side effects such
longer autoneg process.
In our ls102x designs this problem leads to long autoneg times (> 4 sec)
in case board rgmii link is 100Mbps capable only.
Limiting the rgmii link capabilities provides faster and smoother
link establishment.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Read Linux PPFE firmware from flash partition and pass it to Linux through
FDT entry. So that we can avoid placing PPFE firmware in Linux rootfs.
(FDT may increase at max by 64KB)
Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Signed-off-by: Anji J <anji.jagarlmudi@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Since 291da96b8e ("clk: Allow clock defaults to be set during re-reloc
state for SPL only") it has been impossible to set clock defaults before
relocation. This is annoying on boards without SPL, since there is no way
to set clock defaults before U-Boot proper. In particular, the aisram rate
must be changed before relocation on the K210, since U-Boot will hang if we
try and change the rate while we are using aisram.
To get around this, extend the stage parameter to allow force setting
defaults, even if they would be otherwise postponed for later. A device
tree property was decided against because of the concerns in the original
commit thread about the overhead of repeatedly parsing the device tree.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When using bootefi to boot a EFI binary, u-boot is supposed to
provide networking service for EFI application. Currently, 'pfe stop'
command is called from bootcmd before running bootefi. As a result
network stops working for EFI applications and console is flooded with
"Rx pkt not on expected port" messages.
Implement board_quiesce_devices() for ls1012a boards and call
pfe_command_stop() from it instead of calling 'pfe stop' from
*_bootcmd and bootcmd.
Tested-by: Anji Jagarlmudi <anji.jagarlmudi@nxp.com>
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
[Fixed checkpatch space error]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Removed call of ofnode_translate_address() after ofnode_read_resource
in luton_switch.c:luton_probe(); it is unnecessary since
the commit feb7ac457c ("dm: core: Add address translation in
fdt_get_resource").
Fixes: feb7ac457c ("dm: core: Add address translation in fdt_get_resource")
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reported-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
With the last user of this driver removed, remove the driver.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Until now the mvpp2 driver used an extra 'phy-speed'
DT property in order to differentiate between the
SGMII and SGMII @2.5GHz. As there is a dedicated
PHY_INTERFACE_MODE_SGMII_2500 flag to mark the latter
start using it and drop the custom flag.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Tested-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Currently, there are 2 valid cases for interface, PHY
and mdio relation:
- If an interface has PHY handler, it'll call
mdio_mii_bus_get_from_phy(), which will register
MDIO bus.
- If we want to use fixed-link for an interface,
PHY handle is not defined in the DTS, and no
MDIO is registered.
There is a third case, for some boards (with switch),
the MDIO is used for switch configuration, but the interface
itself uses fixed link. This patch allows this option by
checking if fixed-link subnode is defined, in this case,
MDIO bus is registers, but the PHY address is set to
PHY_MAX_ADDR for this interface, so this interface will
not try to access the PHY later on.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Ben Peled <bpeled@marvell.com>
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Ben Peled <bpeled@marvell.com>
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
GMII_SPEED should be enabled for 2.5G speed
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Yan Markman <ymarkman@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Because the mvpp2 driver now relies on the PHYLIB and
the external MDIO driver, configuring low level
SMI bus settings is redundant.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
1. Differ between Port1 RGMII and SFI modes in Netcomplex config.
2. Remove XPCS config from SFI mode.
Port1 doesn't XPCS domain, XPCS config should be removed.
Access to Port1 XPCS can cause stall.
3. Add Port1 MPCS configurations.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
When the PHY interface is set as TXID & RXID, the delays should be taken from DT,
but first they should not be hardcoded since the PHY driver will set them.
Fixes: 798424e857 ("net: designware: add Amlogic Meson8b & later glue driver")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Currently driver may end up caching disabled port ID as active
interface. Fix this by bailing out earlier in case port is marked
disabled in the DT.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
CPSW NUSS IP on K3 SoCs can have more than one external port (upto 8)
Therefore increase AM65_CPSW_CPSWNU_MAX_PORTS to 9 (8 ext + 1 Root port)
as preparation to allow any one of the 8 ports to be used as ethernet
interface in U-Boot.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
If we fail to probe for whatever reason, we cannot unregister/free the
MII bus unless we registered it with fec_get_miibus. This fixes FECs
sharing an MDIO bus from destroying it, preventing the other FEC from
using it.
Fixes: 6a895d039b ("net: Update eQos driver and FEC driver to use eth phy interfaces")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
If a phy is disabled, don't use it. This matches Linux's behavior.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
binman FMAP improvements
minor test improvements and fixes
minor dm improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmCKoLERHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYCpgf/ROfOg76k18PdWcQTZr10CnU0iqTaOyYx
129hvb4n4bx4Q7Zr/HrWT6y7vvD01NOiNCwSX8qdF7S1bqs2/2AM+Yk/vLimXVOg
UDGXGRABkbHQFVMzBUSmlmQvKoG5G6AhS6/5/F7q4jj+QCVMGarves7G7ImhFOFw
6WKeNGv6FWX4UPSxm0TDJETiIqURNZOsu2vU9DmkR/b1eY13/qf/9J4zzEP1DaJt
7PrKmyblRhPlMsi59EjNyEQOnY/A17en8Ik3Zt336tLPELlczRc4Xp8HslQsy2i3
o457il6x8kl828oVwm3Sx4R/UvM8+qE1jWRcPA7vWrxCy3+AqDcTfQ==
=tiPD
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-29apr21' of https://source.denx.de/u-boot/custodians/u-boot-dm
buildman environment fix
binman FMAP improvements
minor test improvements and fixes
minor dm improvements
Today of_address_to_resource() is called only in
ofnode_read_resource() for livetree support and
fdt_get_resource() is called when livetree is not supported.
The fdt_get_resource() doesn't do the address translation
so when it is required, but the address translation is done
by ofnode_read_resource() caller, for example in
drivers/firmware/scmi/smt.c::scmi_dt_get_smt_buffer() {
...
ret = ofnode_read_resource(args.node, 0, &resource);
if (ret)
return ret;
faddr = cpu_to_fdt32(resource.start);
paddr = ofnode_translate_address(args.node, &faddr);
...
The both behavior should be aligned and the address translation
must be called in fdt_get_resource() and removed for each caller.
Fixes: a44810123f ("dm: core: Add dev_read_resource() to read device resources")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
The commit 6c993815bb ("net: phy: xilinx: Be compatible with live OF
tree") change driver behavior to while loop which wasn't correct because
the driver was looping over again and again. The reason was that
ofnode_valid() is taking 0 as correct value.
Fix it by changing while loop to ofnode_for_each_subnode() which is only
loop over available nodes.
Fixes: 6c993815bb ("net: phy: xilinx: Be compatible with live OF tree")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The dw_eth_pdata is not accessible from the mdio device, it gets the mdio bus plat
leading to random sleeps (-10174464 on Odroid-HC4).
This moves the dw_mdio_reset function to a common one taking the ethernet
device as parameter and use it from the dw_mdio_reset and dm_mdio variant functions.
Fixes: 5160b4567c ("net: designware: add DM_MDIO support")
Reported-by: Mark Kettenis <mark.kettenis@xs4all.nl>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Commit eb5a2b6710 ("net: sun8i-emac: Determine pinmux based on SoC,
not EMAC type") switched the pinmux setup over to look at
CONFIG_MACH_SUN* symbols, to find the appropriate mux value.
Unfortunately this patch missed to check for the H5, which is
pin-compatible to the H3, but uses a different Kconfig symbol (because
it has ARMv8 vs. ARMv7 cores).
Replace the pure SUN8I_H3 symbol with the joint SUNXI_H3_H5 one, which is
there to cover the peripherals common to both SoCs.
Also explicitly list each supported SoC, and have an error message in the
fallback case, to avoid those problems in the future.
This fixes Ethernet support on all H5 boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Samuel Holland <samuel@sholland.org> # Orange Pi PC2
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Sometimes no traffic was getting out on the ports, the root cause was
a wrong configuration of the Serdes6G, which is used on jr2 pcb111.
This patch fixes this issue by applying the correct configuration.
Fixes: 5e1d417bec ("net: Add MSCC Jaguar2 network driver.")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Make sure to reset the switch core at probe time.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
To squash that nasty warning message and make better use of the newly
gained OF_CONTROL feature, let's convert the calxedagmac driver to the
"new" driver model.
The conversion is pretty straight forward, mostly just adjusting the
use of the involved data structures.
The only actual change is the required split of the receive routine into
a receive and free_pkt part.
Also this allows us to get rid of the hardcoded platform information and
explicit init calls.
This also uses the opportunity to wrap the code decoding the MMIO
register base address, to make it safe for using PHYS_64BIT later.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The fdt node offset is apparently not set properly when probed
causing no MDIO busses to be found. Fix this by obtaining the
offset.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Revert a change that occured between the Marvell SDK-10.1.1.0
and SDK-10.3.1.1 which broke QSMII phy support.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
At present the tsec driver uses a non-standard DT bindings to get
its <reg> base / size. The upstream Linux kernel seems to require
the <reg> base / size to be put under a subnode of the eTSEC node
with a name prefix "queue-group". This is not documented in the
kernel DT bindings, but it looks every dtsi file that contains the
eTSEC node was written like this.
This commit updates the tsec driver to handle this case.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
dev_remap_addr() eventually calls dev_read_addr_index(), while
pdata->iobase holds the return value of dev_read_addr() that calls
dev_read_addr_index() too. Such duplication can be avoided by using
map_physmem() directly.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The DSA sandbox driver is used for unit testing the DSA class code.
It implements a simple 2 port switch plus 1 CPU port, and uses a
very simple tag to identify the ports.
The DSA sandbox device is connected via CPU port to a regular Ethernet
sandbox device, called 'dsa-test-eth, managed by the existing eth
sandbox driver. The 'dsa-test-eth' is not intended for testing the
eth class code however, but it is used to emulate traffic through the
'lan0' and 'lan1' front pannel switch ports. To achieve this the dsa
sandbox driver registers a tx handler for the 'dsa-test-eth' device.
The switch ports, labeled as 'lan0' and 'lan1', are also registered
as eth devices by the dsa class code this time. So pinging through
these switch ports is as easy as:
=> setenv ethact lan0
=> ping 1.2.3.5
Unit tests for the dsa class code were also added. The 'dsa_probe'
test exercises most API functions from dsa.h. The 'dsa' unit test
simply exercises ARP/ICMP traffic through the two switch ports,
including tag injection and extraction, with the help of the dsa
sandbox driver.
I took care to minimize the impact on the existing eth unit tests,
though some adjustments needed to be made with the addition of
extra eth interfaces used by the dsa unit tests. The additional eth
interfaces also require MAC addresses, these have been added to the
sandbox default environment.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-Id: <20210216224804.3355044-5-olteanv@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Now that the fixed phy driver has been fully adapted to OF APIs,
and dm_eth_phy_connect() already can handle the fixed phy, call
dm_eth_phy_connect() directly in the DM tsec driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210216224804.3355044-4-olteanv@gmail.com>
[bmeng: split from "net: mdio: teach dm_eth_phy_connect to connect to fixed PHY"]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Update fixedphy_probe() to support the old DT binding.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The printf statement doesn't end with a newline. Add it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The PHY driver ops should be made static.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Simplify the logic of phy_connect_fixed() by using the new API
ofnode_phy_is_fixed_link(), which brings additional bonus of
supporting the old DT bindings.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
At present phy_connect_gmii2rgmii() is implemented using a DM API
dev_of_offset() hence it cannot support a non-DM configuration.
Remove the non-DM version prototype of phy_connect_gmii2rgmii()
and make the driver depend on CONFIG_DM_ETH.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Following the same updates that were done to the fixed phy driver,
use ofnode_ APIs instead of fdt_ APIs so that the Xilinx PHY driver
can support live DT.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In drivers/net/phy/Kconfig, CONFIG_PHY_FIXED already depends on
CONFIG_DM_ETH, so the function prototype definition when
CONFIG_DM_ETH=n does nothing, so it can be dropped. It is also
never reachable, since the whole function is already under #ifdef
CONFIG_PHY_FIXED (which again, as I said, depends on CONFIG_DM_ETH=y).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210216224804.3355044-3-olteanv@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
On systems that use CONFIG_OF_LIVE, the "ofnode" type is defined
as const struct device_node *np, while on the flat DT systems it
is defined as a long of_offset into gd->fdt_blob.
It is desirable that the fixed PHY driver uses the higher-level
ofnode abstraction instead of parsing gd->fdt_blob directly,
because that enables it to work on live OF systems.
The fixed PHY driver has used a nasty hack since its introduction in
commit db40c1aa1c ("drivers/net/phy: add fixed-phy /
fixed-link support"),
which is to pass the long gd->fdt_blob offset inside int phydev->addr
(a value that normally holds the MDIO bus address at which the PHY
responds). Even ignoring the fact that the types were already
mismatched leading to a potential truncation (flat OF offset was
supposed to be a long and not an int), we really cannot extend this
hack any longer, because there's no way an int will hold the other
representation of ofnode, the struct device_node *np.
So we unfortunately need to do the right thing, which is to use the
framework introduced by Grygorii Strashko in
commit eef0b8a930 ("net: phy: add ofnode node to struct phy_device").
This will populate phydev->node for the fixed PHY.
Note that phydev->node will not be valid in the probe function, since
that is called synchronously from phy_device_create and we really have
no way of passing the ofnode directly through the phy_device_create API.
So we do what other drivers do too: we move the OF parsing logic from
the .probe to the .config method of the PHY driver. The new function
will be called at phy_config() time.
I do believe I've converted all the possible call paths for creating
a PHY with PHY_FIXED_ID, so there is really no reason to maintain
compatibility with the old logic of retrieving a flat OF tree offset
from phydev->addr. We just pass 0 to phydev->addr now.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20210216224804.3355044-2-olteanv@gmail.com>
[bmeng: keep fixedphy_probe(); update mdio-uclass.c to handle fixed phy]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
These boards have not been converted to CONFIG_DM_MMC by the deadline.
Remove them. As the P5020 is the last ARCH_P5020 platform, remove that
support as well.
Cc: Andy Fleming <afleming@gmail.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. It is also the only ARCH_T2081 board so remove that support
as well.
Cc: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds a proper glue driver for the Designware DWMAC ethernet MAC IP
found in the Amlogic Meson8, GXBB, GXL, GXM, G12A, G12B & SM1 SoCs.
This is aimed to replace the static ethernet link setup found on the board
init code for the Amlogic SoC based boards.
Tested on a libretech-cc (S905x Internal RMII 10/100 PHY) and Khadas VIM3 (A113d
with external 10/100/1000 RGMII PHY) to cover the most extreme setups.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Amlogic G12A & compatible SoCs embeds a mux to either communicate with
the external PHY or the internal 10/100 PHY.
This adds support for this mux as a MDIO MUX device.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add support for DM_MDIO to connect to PHY and expose a MDIO device for the
internal MDIO bus in order to dynamically connect to MDIO PHYs with DT
with eventual MDIO muxes in between.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add support for MMIO register MDIO muxes based on the Linux mdio-mux-mmioreg driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The code was trying to disable PCS auto-negotiation when a fixed-link node
is present and enable it otherwise. However, the PCS registers were being
written before the PCSSEL bit was set in the network configuration
register, and it appears that in this state, PCS register writes are
ignored. The result is that the intended change only took effect on the
second network operation that was performed, since at that time PCSSEL is
already enabled.
Fix the order of register writes so that PCS registers are only written to
after the PCS is enabled.
Fixes: 26e62cc971 ("net: gem: Disable PCS autonegotiation in case of fixed-link")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When copying to a u32 field we should use sizeof(u32) and not
sizeof(*u32) in memcpy.
On 64bit systems like cortina_presidio-asic-emmc_defconfig using
sizeof(*u32) leads to a buffer overrun.
Fixes: febe13b438 ("net: cortina_ni: Add eth support for Cortina Access CAxxxx SoCs")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
qspi:
- Support for dual/quad mode
- Fix speed handling
clk:
- Add clock enable function for zynq/zynqmp/versal
gem:
- Enable clock for Versal
- Fix error path
- Fix mdio deregistration path
fpga:
- Fix buffer alignment for ZynqMP
xilinx:
- Fix reset reason clearing in ZynqMP
- Show silicon version in SPL for Zynq/ZynqMP
- Fix DTB selection for ZynqMP
- Rename zc1275 to zcu1275 to match DT name
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYDUezQAKCRDKSWXLKUoM
IbtgAJ9jZ+BOtwFaHR19TENC2DsHTINnnwCfSDn3fU0OFJRI0HD7pRxXr4xrb3M=
=Kr8x
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.04-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.04-rc3
qspi:
- Support for dual/quad mode
- Fix speed handling
clk:
- Add clock enable function for zynq/zynqmp/versal
gem:
- Enable clock for Versal
- Fix error path
- Fix mdio deregistration path
fpga:
- Fix buffer alignment for ZynqMP
xilinx:
- Fix reset reason clearing in ZynqMP
- Show silicon version in SPL for Zynq/ZynqMP
- Fix DTB selection for ZynqMP
- Rename zc1275 to zcu1275 to match DT name
Enable rx clock along with tx clock for versal platform. Use compatible
data to enable/disable clocks in the driver.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
A lot of Xilinx drivers are checking -ENOSYS which means that clock driver
doesn't have enable function. Remove this checking from drivers and create
dummy enable function as was done for clk_fixed_rate driver by
commit 6bf6d81c11 ("clk: fixed_rate: add dummy enable() function").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This driver is used for the Ethernet switch integrated into LS1028A NXP.
Felix on LS1028A has 4 front panel ports and two internal ports, I/O
to/from the switch is done through an ENETC Ethernet interface.
The 4 front panel ports are available as Ethernet interfaces and can be
used with the typical network commands like tftp.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
DSA stands for Distributed Switch Architecture and it covers switches that
are connected to the CPU through an Ethernet link and generally use frame
tags to pass information about the source/destination ports to/from CPU.
Front panel ports are presented as regular ethernet devices in U-Boot and
they are expected to support the typical networking commands.
DSA switches may be cascaded, DSA class code does not currently support
this.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
The DSA (Distributed Switch Architecture) implementation has made a
design decision when it got introduced to the Linux kernel in 2008.
That was to hide away from the user the CPU-facing Ethernet MAC, since
it does not make sense to register it as a struct net_device (UCLASS_ETH
udevice for U-Boot), because that would never be beneficial for a user:
they would not be able to use it for traffic, since conceptually, a
packet delivered to the CPU port should loop back into the system.
Nonetheless, DSA has had numerous growing pains due to the lack of a
struct net_device for the CPU port, but so far it has overcome them.
It is unlikely at this stage of maturity that this aspect of it will
change.
We would like U-Boot to present the same information as Linux, to be at
parity in terms of number of interfaces, so that ethNaddr environment
variables could directly be associated between U-Boot and Linux.
Therefore, we would implicitly like U-Boot to hide the CPU port from the
user as well.
But the paradox is that DSA still needs a struct phy_device to inform
the driver of the parameters of the link that it should configure the
CPU port to. The problem is that the phy_device is typically returned
via a call to phy_connect, which needs an udevice to attach the PHY to,
and to search its ofnode for the 'fixed-link' property. But we don't
have an udevice to present for the CPU port.
Since 99% of DSA setups are MAC-to-MAC connections between the switch
and the host Ethernet controller, the struct phy_device is going to be a
fixed PHY. This simplifies things quite a bit. In U-Boot, a fixed PHY
does not need an MDIO bus, and does not need an attached dev either.
Basically, the phy_connect call doesn't do any connection, it just
creates the fixed PHY.
The proposal of this patch is to introduce a new fixed_phy_create
function which will take a single argument: the ofnode that holds this:
port@4 {
reg = <4>;
phy-mode = "internal";
fixed-link {
speed = <2500>;
full-duplex;
};
};
and probe a fixed PHY driver using the information from this ofnode.
DSA will probably be the only user of this function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Unlike the Linux fixed PHY driver, the one in U-Boot does not attempt to
emulate the clause 22 register set of a gigabit copper PHY driver
through the swphy framework. Therefore, the limitation of being unable
to support speeds higher than gigabit in fixed-link does not apply to
the U-Boot fixed PHY driver. This makes the fixed-link U-Boot
implementation more similar to the one from phylink, which can work with
any valid link speed.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
At present this function does not accept a size for the FIT. This means
that it must be read from the FIT itself, introducing potential security
risk. Update the function to include a size parameter, which can be
invalid, in which case fit_check_format() calculates it.
For now no callers pass the size, but this can be updated later.
Also adjust the return value to an error code so that all the different
types of problems can be distinguished by the user.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Bruce Monroe <bruce.monroe@intel.com>
Reported-by: Arie Haenel <arie.haenel@intel.com>
Reported-by: Julien Lenoir <julien.lenoir@intel.com>
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well. Remove it.
As this is the last SH4A board, remove that support as well.
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well. Remove it.
Patch-cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Patch-cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
If probe fails, the mdio bus isn't unregistered. Fix it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Current MDIO wait time is too long, which introduce long delay when
PHY negotiation register checking. Reduce it to 10us
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fugang Duan <Fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
We have encountered circumstances when a board design does not include
pull-up resistors on the external MDIO buses which are not used. This
leads to the MDIO data line not being pulled-up, thus the MDIO controller
will always see the line as busy.
Without a timeout in the MDIO bus driver, the execution is stuck in an
infinite loop when any access is initiated on that external bus.
Add a timeout in the driver so that we are protected in this
circumstance. This is similar to what is being done in the Linux
xgmac_mdio driver.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
priv->iobase was declared as phys_addr_t which is now a 64-bit
address. In a 32-bit build, this causes the following warning
seen when building ftmac100.c:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Cast priv->iobase with uintptr_t.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The pinmux choice for the RMII/RGMII pins the EMAC is connected to is
not dependent on the EMAC IP, but on the SoC it is integrated in.
Deriving the pinmux from the DT compatible string (as we do at the
moment) will thus cause problems with certain EMAC IP / SoC combinations.
To avoid this exact issue with the H616, let's use our Kconfig MACH
symbols to choose the correct pinmux setup.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
At the moment we only consider the EPHY register for those SoCs were
we actually have an internal PHY to configure. However even other SoCs
have this register, an expect the EPHY select bit to be cleared for
proper operation with an external PHY.
Rework sun8i_emac_set_syscon_ephy() to be called regardless of the EMAC
model, and clear the H3_EPHY_SELECT bit if no internal PHY is used.
We get away without it so far because SoCs like the A64 clear this bit
on reset, but we need to explicitly clear it on the H616, for instance.
The Linux driver does so as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
The phydev structure has a PHY OF node pointer in it, use that OF node
first when looking up PHY OF node properties, since that is likely the
correct PHY OF node pointer. If the pointer is not valid, which is the
case e.g. on legacy DTs, fall back to parsing MAC ethernet-phy subnode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Add phy driver support for MACs embedded inside Cortina Access SoCs
Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Tom Rini <trini@konsulko.com>
CC: Aaron Tseng <aaron.tseng@cortina-access.com>
Moved out PHY specific code out of Cortina NI Ethernet driver
and into a Cortina Access PHY interface driver
Add some missing address translations from virtual address in local DRAM
to physical address, which is needed for the DMA transactions to work
correctly.
This issue was detected while testing the e1000 driver on the MIPS
Octeon III platform, which needs address translation.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Using (dm_)pci_virt_to_mem() is incorrect to translate the virtual
address in local DRAM to a physical address. The correct macro here
is virt_to_phys() so switch to using this macro.
As virt_to_bus() is now not used any more, this patch also removes
both definitions (DM and non-DM).
This issue was detected while testing the e1000 driver on the MIPS
Octeon III platform, which needs address translation.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
bus_to_phys() is defined but not referenced at all. This patch removes
it completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
So far all GBit users of the sun8i-emac driver were using the "rgmii"
PHY mode, even though this turns out to be wrong. It just worked because
the PHY driver doesn't do the proper setup (yet).
In fact for most boards the "rgmii-id" or "rgmii-txid" PHY modes are the
correct ones.
To allow the DTs to describe the phy-mode correctly, and to stay
compatible with Linux, at least allow those other RGMII modes in the
driver.
This avoids breakage if mainline DTs will be synced with U-Boot.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmAOkP8cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKedCACiDHgP71VKSOiYnEU4
vHD/ANmfMXqnsL71PpSdagnBRAl4vpm46CnD+Mq7RtchxGDNufX6tWJSI04Ci0bC
mfmIfVEjePOnuUayylJ55OlrtJVpBqJFPqxM6MFcIF7nRja1r5thV1jTLNu+b4sm
gg2sk1mC/531Lxbk8S7x+diPymNRArEm3IEw+xEqUhsNVQCKjOEcxi/BWIB2prR3
NxRSGdW3j4CKdBqt7uOL1bqApeQQ9m0/gm1tE3hMXUo09I7uXmb7U52aKb5cV8L+
8ZOlbav6yaPACe3p9npp4K0ByXMmYHjeo1NZW4cvAoKfzragdu0Cv7f0ssVCgrlR
p1e3
=xS6A
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.04-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.04 cycle
This feature set includes macb updates for all interfaces and new
sama7g5 variant support; micrel ksz9031 DLL support; a new board from
Giant based on Adafruit feather form factor which contains a SAMA5D27
SoC; several fixes regarding the NAND flash PMECC block; and pincontrol
drive strength support for pio4 controller.
This patch adds ethernet driver for MediaTek MT7620 SoC.
The MT7620 SoC has a built-in ethernet (Frame Engine) and a built-in
7-port switch and two xMII interfaces (can be MII/RMII/RGMII).
The port 0-3 of the switch connects to intergrited FE PHYs. Port 4 can be
configured to connect to either the intergrited FE PHY, or the xMII.
Port 5 always connects to the xMII. Port 6 is the CPU port.
This driver supports MT7530 giga switch connects to port 5.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Take into account all RGMII interface types. Depending on it
the RGMII PHY's timings are setup.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
clk_set_rate() returns the set rate in case of success and a
negative number in case of failure. Consider failure only the
negative numbers.
Fixes: 3ef64444de ("dm: net: macb: Implement link speed change callback")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Different implementation of USER IO register needs different
mapping for bit fields of this register. Add implementation
for this and, since clken is part of USER IO and it needs to
be activated based on per SoC capabilities, add caps in
macb_config where clken specific information needs to be filled.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
The DWMAC4 IP has the possibility to skip up to 7 AXI bus width size words
after the descriptor. Use this to pad the descriptors to cacheline size and
remove the need for noncached memory altogether. Moreover, this lets Tegra
use the generic cache flush / invalidate operations.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
A sporadic condition occurs when the "bad packet" error is triggered
repeatedly, which results in "bad packet" messages scrolling on the
console during transfer. To avoid triggering this, reset the internal
RXFC count on the first occurance of the "bad packet", which forces
the code to re-read the RX packet count from the MAC, and prevents
any additional "bad packet" messages if there are no more packets in
the MAC. Also print better debug information if this condition occurs.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Tom Rini <trini@konsulko.com>
Implement programming MAC address to the hardware also for device model
configuration.
Fixes: b565b18a29 ("board: ge: bx50v3: Enable DM for PCI and ethernet")
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Read phy address from device tree and use it to find the phy device
if not found then search in the range of 0 to 31.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Enable 32-bit or 64-bit DMA in the macb driver based on the macb
hardware compatibility and it is configured with structure macb_config
in the driver.
The Microchip PolarFire SoC Memory Protection Unit(MPU) gives the 64-bit
DMA access with the GEM, the MPU transactions on the AXI bus is 64-bit
not 32-bit So 64-bit DMA is enabled for the Microchip PolarFire SoC GEM.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Add a return value to bb_miiphy_init and use it directly in the
post-relocation init sequence, rather than using a wrapper stub.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In non-secure mode (EL2), MAC driver calls the SMC/PSCI services
provided by ATF to setup the PHY interface.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
